237108_36 GTH 844m 844 237108
User Manual: GTH-844
Open the PDF directly: View PDF 
.
Page Count: 67
| Download | |
| Open PDF In Browser | View PDF |
Operator's Manual GTH-844 with Maintenance Information Third Edition Sixth Printing Part No. 237108 Operator's Manual Third Edition • Sixth Printing Front Matter Contents Introduction ........................................................... 1 Symbol and Hazard Pictorials Definitions ............. 5 General Safety ...................................................... 7 Work Area Safety .................................................. 9 Legend ................................................................ 17 Controls ............................................................... 18 Inspections .......................................................... 22 Operating Instructions ......................................... 33 Transport and Lifting Instructions ....................... 44 Maintenance ....................................................... 47 Attachments ........................................................ 51 Specifications ...................................................... 63 Load Charts ........................................................ 64 Copyright © 2012 by Terex Corporation Third Edition: Sixth Printing, January 2015 Genie is a registered trademark of Terex South Dakota, Inc. in the U.S.A. and many other countries. “GTH” is a trademark of Terex South Dakota, Inc. Complies with ANSI/ITSDF B56.6, CSA B335 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Introduction Introduction About this manual Intended Use Genie appreciates your choice of our machine for your application. Our number one priority is user safety, which is best achieved by our joint efforts. This book is an operation and daily maintenance manual for the user or operator of a Genie machine. A variable reach rough terrain forklift truck is defined as a wheeled type truck with a pivoting boom, which may be equipped with various attachments for picking, transporting and placing loads with the established load range charts. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, contact Genie. Bulletin Distribution and Compliance Product Identification The machine serial number is located on the serial label. Serial label (located inside fork frame) (models with quick attach frame) Serial label (located inside riser) Use of this product in any other way is prohibited and contrary to its intended use. Safety of product users is of paramount importance to Genie. Various bulletins are used by Genie to communicate important safety and product information to dealers and machine owners. The information contained in the bulletins is tied to specific machines using the machine model and serial number. Distribution of bulletins is based on the most current owner on record along with their associated dealer, so it is important to register your machine and keep your contact information up to date. Serial number stamp Part No. 237108 To ensure safety of personnel and the reliable continued operation of your machine, be sure to comply with the action indicated in a respective bulletin. GTH-844 1 Operator's Manual Third Edition • Sixth Printing Introduction Contacting the Manufacturer At times it may be necessary to contact Genie. When you do, be ready to supply the model number and serial number of your machine, along with your name and contact information. At minimum, Genie should be contacted for: Accident reporting Danger Questions regarding product applications and safety Failure to obey the instructions and safety rules in this manual will result in death or serious injury. Standards and regulatory compliance information Current owner updates, such as changes in machine ownership or changes in your contact information. See Transfer of Ownership, below. Do Not Operate Unless: You learn and practice the principles of safe Transfer of Machine Ownership machine operation contained in this operator’s manual. Taking a few minutes to update owner information will ensure that you receive important safety, maintenance and operating information that applies to your machine. 1 Avoid hazardous situations. Know and understand the safety rules before going on to the next section. Please register your machine by visiting us on the web at www.genielift.com or by calling us toll free at 1-800-536-1800. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. 5 Only use the machine as it was intended. You read, understand and obey the manufacturer’s instructions and safety rules—safety and operator’s manuals and machine decals. You read, understand and obey employer’s safety rules and worksite regulations. You read, understand and obey all applicable governmental regulations. You are properly trained to safely operate the machine. 2 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Introduction Hazard Classification Standards Decals on this machine use symbols, color coding and signal words to identify the following: Many aspects of rough terrain forklift operation and testing are discussed in standards published by the American National Standards Institute and the Industrial Truck Standards Development Foundation. These standards are updated on a regular basis with addenda. It is recommended that you purchase and refer to the following standards. Safety alert symbol—used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER WARNING CAUTION NOTICE Part No. 237108 Indicates a hazardous situation which, if not avoided, will result in death or serious injury. ANSI/ITSDF B56.6 - Rough Terrain Forklift Trucks Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CSA B335 - Safety Standard for Lift Trucks The ANSI standard can be downloaded from www.ITSDF.org The CSA standard can be downloaded from www.csa.ca Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Indicates a property damage message. GTH-844 3 Operator's Manual Third Edition • Sixth Printing Introduction Safety Sign Maintenance Replace any missing or damaged safety signs. Keep operator safety in mind at all times. Use mild soap and water to clean safety signs. Do not use solvent-based cleaners because they may damage the safety sign material. 4 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions Electrocution hazard Maintain required clearance Crush hazard No people under load Read the operator’s manual Injection hazard Use a piece of cardboard or paper to search for leaks Maintain required clearance Crush hazard Always wear seat belt Tip-over hazard Tip-over hazard Crush hazard Keep away from moving parts Crush hazard Keep away from moving parts Burn hazard Do not loosen cap until cool. Explosion / Burn hazard No smoking. No open flame. Burn hazard Allow surfaces to cool Crush hazard Keep away from moving parts Only trained maintenance personnel should access compartments Part No. 237108 GTH-844 5 Operator's Manual Third Edition • Sixth Printing Symbol and Hazard Pictorials Definitions Explosion / Burn hazard No smoking. No open flame. Refer to load charts and manual. Sway operation 6 Keep load low GTH-844 Fall hazard Only use an approved work platform Part No. 237108 Third Edition • Sixth Printing Operator's Manual General Safety General Safety 214418 214418 237599 215268 237970 214419 82558 214419 237599 97602 237601 237605 82558 215268 237598 214418 237598 237970 237598 97667 214418 237971 97667 237605 28175 237601 28175 1262614 97602 1262614 237971 Part No. 237108 GTH-844 237970 237598 7 Operator's Manual Third Edition • Sixth Printing General Safety 215648 237721 215646 215647 215646 215644 215647 133031 237721 237726 237722 82560 215648 237720 215646 237720 215644 237720 237726 215646 133031 82473 215645 82560 237722 82473 1262615 1262615 215645 8 GTH-844 215644 237720 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Work Area Safety Work Area Safety Overturning Hazards Using the appropriate load chart for the machine configuration, confirm that the load is within the rated capacity of the machine. Do not exceed the rated load. Do not attempt to jump free of the machine during a tip-over. The ROPS (Roll Over Protective Structure) is designed to protect you. If the telehandler starts to tip over: - Do not jump - Brace yourself and stay in the seat The load center on the fork (if equipped) must be equal to or less than the load center indicated on the load chart. If the load center is further from the fork face than shown on the load chart, refer to the Load Chart section of this manual. - Keep your seat belt fastened - Hold on firmly All loads shown on the load chart are based on the machine being on firm, level ground, the frame being level, the forks being positioned evenly on the carriage, the load being centered on the forks, the tires being properly sized and properly inflated, and the telehandler being in good operating condition. If using accessories, read, understand and obey the decals, instructions and manuals with the accessory. - Lean away from the point of impact Do not raise the boom unless the machine is level. The machine level indicator should be at zero degrees. Do not level the machine using the frame sway control unless the boom angle indicator is at zero degrees or less. Do not raise the load unless the ground can support all forces imposed by the machine. Do not use the sway control to position an elevated load. Do not lower a load without retracting the boom first. Do not operate the machine if the load chart is missing. Do not exceed the rated capacity for each configuration. Part No. 237108 GTH-844 9 Operator's Manual Third Edition • Sixth Printing Work Area Safety Traveling on Slopes Hazards Do not raise a load and then drive to position it. When driving, keep the boom at or below horizontal and keep the load close to the ground. When driving, keep the boom at or below horizontal and keep the load close to the ground. Operate the machine at speeds that will keep the load under control. Start and stop movements smoothly. Do not raise a load unless the load is properly positioned or secured on the forks or approved attachment. Do not operate the machine in strong or gusty winds. Do not increase the surface area of the carriage or load. Increasing the area exposed to the wind will decrease machine stability. Use extreme care and slow speeds while driving the machine in the travel position across uneven terrain, steep grades, debris, unstable or slippery surfaces and near holes and drop-offs. Do not alter or disable machine components that in any way affect safety and stability. Do not replace items critical to machine stability with items of different weight or specification. Do not replace factory-installed tires with tires of different specification or ply rating, unless approved by the factory. When the machine is loaded, always travel with the load uphill. When the machine is unloaded, travel with the forks or attachment downhill. On steep terrain, drive only up and down a hill, and always keep the machine in gear. Do not turn across the slope when the machine is traveling up or down a slope. Limit travel path and speed according to the condition of the ground surface, traction, slope, location of personnel and any other factors which may create a hazard. Never drive the machine unless the mast and equipment are in their proper travel position. Whether a machine will tip over during dynamic machine operation involves many factors that need to be considered. Among these are pavement/ground conditions, stability and slope, as well as machine equipment, operator skill, load position, tire inflation, machine speed, etc. Additionally, tip-over of a machine is dependent in large part upon operator inputs such as the speed and smoothness of the operation, as well as the position of the attachment and its load. Construction sites and roads will frequently change slope from place to place, can be hard and soft, and change due to construction activities and weather. Operators should be properly trained and use their best judgment and experience to take the necessary precautions to prevent a tip-over. Operators must assess the job site variables and avoid exceeding the machine's (or operator's) capabilities for terrain and conditions. 10 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Work Area Safety Fall Hazards Collision Hazards Always wear a seat belt when operating the machine. Keep people, equipment and material out of the work area. Do not operate the machine while people are under or near an elevated boom, whether it is loaded or unloaded. Always remain completely inside the cab when operating the machine. When getting in and out of the cab, face the machine, use the steps and handrails provided and always maintain three-point contact. Do not put the transmission into gear unless the brake is applied and personnel and bystanders are clear of the machine and load. Do not use the steering wheel or any other controls as handrails. Do not drive the machine if visibility is obstructed. Do not allow riders on the machine or forks. Do not lift personnel with this machine unless it is equipped with an approved work platform. See Work Platform section. Do not raise the boom unless the brake is applied. Do not operate, without fenders, in conditions where loose debris could hit the operator or accumulate on the cab windows. Do not operate the machine with a faulty back-up alarm. The back-up alarm should sound when the machine is in reverse. Do not operate the machine in low light conditions. An optional work and road light package is available. Operators must comply with employer, job site and governmental rules regarding use of personal protective equipment. Do not drive the machine directly up to anyone. Always make sure that mirrors and cab glass are clean and do not obstruct the operators view of the travel path or load. Part No. 237108 GTH-844 11 Operator's Manual Third Edition • Sixth Printing Work Area Safety Falling Object Hazards Bodily Injury Hazards Operate the machine at speeds that will keep the load under control. Start and stop movements smoothly. Always adjust the seat and fasten the seat belt before starting the engine. Keep people, equipment and material out of the work area. Do not operate the machine while people are under or near an elevated boom, whether it is loaded or unloaded. Do not operate the machine with a hydraulic oil or air leak. An air leak or hydraulic leak can penetrate and/or burn skin. Relieve pressure before disconnecting hydraulic lines. Keep away from leaks and pin holes. Use a piece of cardboard or paper to search for leaks. Do not use your hand. Be sure the load is secure before lifting it. Always make sure the quick attach pin is inserted and secured. Fluid injected into skin must be surgically removed within a few hours by a doctor familiar with this type of injury or gangrene will result. Stay clear of belts and fans when the engine is running. Always operate the machine in a well-ventilated area to avoid carbon monoxide poisoning. Improper contact with components under any cover will cause serious injury. Only trained maintenance personnel should access compartments. Access by the operator is only advised when performing a pre-operation inspection. All compartments must remain closed and secured during operation. Keep body parts, such as hand, fingers and arms, away from moving components. Always use provided latches and handles for opening and closing doors and covers. 12 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Work Area Safety Damaged Machine Hazards Component Damage Hazards Do not use a damaged or malfunctioning machine. Conduct a thorough pre-operation inspection of the machine and test all functions before each work shift. Immediately tag and remove from service a damaged or malfunctioning machine. Be sure all maintenance has been performed as specified in this manual and the appropriate Genie service manual. Do not use any battery or charger greater than 12V to jump-start the engine. Do not use the machine as a ground for welding. Do not steer the front tires on dry pavement when the axle differential lock is activated. Do not lock the axle differential when the machine is moving. For machines equipped with solid tires, do not operate continuously for longer than one hour without allowing the tires to cool down for 30 minutes. Be sure all decals are in place and legible. Be sure the operator's and safety manuals are complete, legible and in the storage container located in the cab. Do not attempt to start the machine by towing or pushing. Do not attempt to use the forks or attachments for prying wedged or frozen loads free. Do not push or pull objects or loads with the forks, attachment or boom. Part No. 237108 GTH-844 13 Operator's Manual Third Edition • Sixth Printing Work Area Safety Crush Hazards Burn Hazards Keep clear of moving parts during machine operation and make sure personnel and bystanders are kept clear of moving parts during operation. Allow hot surfaces to cool before touching or servicing. Set the parking brake, put the transmission in neutral and lower the carriage or the attachment to the ground before leaving the machine. Keep clear of elevated components. Support components before performing service. Keep clear of moving parts during machine operation and make sure personnel and bystanders are kept clear of moving parts during operation. Explosion and Fire Hazards Do not start the engine if you smell or detect liquid petroleum gas (LPG), gasoline, diesel fuel or other explosive substances. Do not refuel the machine with the engine running. Refuel the machine and charge the battery only in an open, well-ventilated area away from sparks, flames and lighted tobacco. Do not operate the machine in hazardous locations or locations where potentially flammable or explosive gases or particles may be present. Do not spray ether into engines equipped with glow plugs or air intake grid heaters. 14 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Work Area Safety Electrocution Hazards This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Obey all local and governmental regulations regarding required clearance from electrical power lines. At a minimum, the required clearance contained in the chart below must be followed. Always contact the electrical power line owner. The electrical power shall be disconnected or the power lines moved or insulated before machine operations begin. Allow for boom and attachment movement, electrical line sway or sag, and beware of strong or gusty winds. Keep away from the machine if it contacts energized power lines. Personnel on the ground or in the cab must not touch or operate the machine until energized power lines are shut off. Do not operate the machine during lightning or storms. Line Voltage Required Clearance 0 to 50KV 10 ft >50 to 200KV 15 ft 4.60 m >200 to 350KV 20 ft 6.10 m >350 to 500KV 25 ft 7.62 m >500 to 750KV 35 ft 10.67 m >750 to 1000KV 45 ft 13.72 m over 1000kV 3.05 m see below For power lines over 1000kV, the minimum clearance distance must be established by the utility owner or operator or by a registered professional engineer who is a qualified person with respect to electrical power transmission and distribution. Do not use the machine as a ground for welding. Part No. 237108 GTH-844 15 Operator's Manual Third Edition • Sixth Printing Work Area Safety Battery Safety Employer's Responsibilities Burn Hazards Batteries contain acid. Always wear protective clothing and eye wear when working with batteries. Employers are responsible for providing a safe work environment and for complying with local and national governmental regulations. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. Explosion Hazards Keep sparks, flames and lighted tobacco away from batteries. Batteries emit explosive gas. Electrocution Hazard Avoid contact with electrical terminals. 16 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Legend Legend 1 2 3 4 5 18 6 7 17 8 16 9 15 10 14 13 12 11 1 2 3 4 5 6 7 8 9 Interior rear view mirror Left to right level indicator Steering wheel Control handle Front to rear level indicator Boom angle indicator Boom Cab Hydraulic oil level gauge (under cover) Part No. 237108 10 11 12 13 14 15 16 17 18 GTH-844 Engine (on opposite side of machine) Fuse panel Forks Exterior rear view mirror Seat belt Seat Brake pedal Accelerator pedal Transmission control lever 17 Operator's Manual Third Edition • Sixth Printing Controls Controls 1 2 3 4 5 22 21 6 20 7 19 8 18 9 17 16 10 15 11 14 13 12 Control Panel 1 2 3 4 5 6 7 8 9 10 11 18 Steering wheel Horn button Heater and air conditioning controls (if equipped) Turn signal lever (if equipped) 12V power port, 10A maximum Steer select switch Parking brake switch Ignition switch Load charts Control handle Auxiliary hydraulics switch (if equipped) 12 13 14 15 16 17 18 19 20 21 22 GTH-844 Accelerator pedal Brake pedal Tilt steering pedal Axle differential lock pedal Windshield washer/wiper switch (if equipped) Skylight washer/wiper switch (if equipped) Lights switch (if equipped) Transmission control lever Not used Not used Instrument panel Part No. 237108 Third Edition • Sixth Printing Operator's Manual Controls 1 Steering wheel 8 Turn the steering wheel to the right to turn the front wheels to the right. Turn the steering wheel to the left to turn the front wheels to the left. 2 Turn the key to the left to turn on the accessories. Turn the key to the on position and hold until the glow plug light on the instrument panel turns off. Turn the key to the start position to start the engine. Horn button 9 Press this button and the horn will sound. Release the button and the horn will stop. 3 Heater and air conditioning controls (if equipped) 4 Turn signal lever (if equipped) 12V power port, 10A maximum 6 Steer select switch Push down the right side of the rocker switch to select four-wheel steer. Push the rocker switch to the middle position to select two-wheel steer. Push down the left side of the rocker switch to select crab steer. 7 Pull the control handle back and the boom will raise. Push the control handle forward and the boom will lower. Push the control handle to the right and the boom will extend. Pull the control handle to the left and the boom will retract. Hold down the red thumb switch and pull the control handle back and the forks will tilt up. Hold down the red thumb switch and push the control handle forward and the forks will tilt down. Hold the white finger switch and push the control handle to the right and the machine will sway to the right. Hold the white finger switch and pull the control handle to the left and the machine sway to the left. 11 Auxiliary hydraulics switch (if equipped) Push the left side of the auxiliary hydraulics button and the carriage will swing or rotate to the left. Push the right side of the auxiliary hydraulics button and the carriage will swing or rotate to the right. Parking brake switch Push the top of the rocker switch to turn the parking brake on. The light will be on when the parking brake is on. Push the bottom of the rocker switch to turn the parking brake off. The light will be off when the parking brake is off. Part No. 237108 Load charts 10 Control handle (single) Move the lever up to activate the left turn signal. Move the lever down to activate the right turn signal. Turn the lever to turn on the hazard lights. 5 Ignition switch 12 Accelerator pedal GTH-844 19 Operator's Manual Third Edition • Sixth Printing Controls 13 Brake pedal 18 Lights switch (if equipped) 14 Tilt steering pedal Push the right side of the rocker switch to turn the road lights or the work lights on. Push the left side of the rocker switch to turn the road lights or the work lights off. Push and hold the tilt steering pedal to release the steering column. Move the steering wheel to desired position and release the pedal. 19 Transmission control lever 15 Axle differential lock pedal Move the transmission control lever toward you and move it up for forward gear. Move the lever toward you and move it down for reverse gear. Move the lever to the center position for neutral. Turn the lever clockwise to shift to a lower speed. Turn the lever counterclockwise to shift to a higher speed. Push and hold the axle differential lock pedal to lock the axle differential. Release the pedal to unlock the axle differential. 16 Windshield washer/wiper switch (if equipped) Push the right side of the rocker switch to turn the wiper on. Push and hold the right side of the rocker switch to turn the washer on. Release the switch to turn the washer off. Push the left side of the rocker switch to turn the wiper off. 20 Not used 21 Not used 22 Instrument panel 17 Skylight washer/wiper switch (if equipped) Push the right side of the rocker switch to turn the wiper on. Push and hold the right side of the rocker switch to turn the washer on. Release the switch to turn the washer off. Push the left side of the rocker switch to turn the wiper off. 20 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Controls 1 2 3 15 10 5 25 4 5 20 25 RPM x100 0 30 24 6 23 7 22 8 ! 21 9 ! 10 20 19 18 17 16 14 15 13 12 11 Instrument Panel 1 2 3 4 5 6 7 8 9 10 11 12 13 Fuel level gauge with low fuel indicator light Turn signal indicator lights Tachometer Lights indicator light Engine coolant temperature gauge Engine emissions regeneration disabled indicator light Engine emissions regeneration indicator light Engine emissions system temperature Urea level low indicator light (if equipped) Battery voltage low indicator light Engine oil pressure low indicator light Check engine indicator light Engine stop indicator light Part No. 237108 14 15 16 17 18 19 20 21 22 Four-wheel steer indicator light Two-wheel steer indicator light Crab steer indicator light Brake pressure low indicator light Rear wheels centered indicator light (if equipped) Transmission oil pressure low indicator light Transmission oil temperature high indicator light Not used Hydraulic oil temperature indicator light (if equipped) 23 Not used 24 Glow plug indicator light 25 Engine hour meter and fault code display GTH-844 21 Operator's Manual Third Edition • Sixth Printing Inspections Inspections Pre-operation Inspection Fundamentals It is the responsibility of the operator to perform a pre-operation inspection and routine maintenance. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. The pre-operation inspection is a visual inspection performed by the operator prior to each work shift. The inspection is designed to discover if anything is apparently wrong with a machine before the operator performs the function tests. The pre-operation inspection also serves to determine if routine maintenance procedures are required. Only routine maintenance items specified in this manual may be performed by the operator. Refer to the list on the next page and check each of the items. Know and understand the pre-operation inspection before going on to the next section. 3 Always perform function tests prior to use. 4 Inspect the workplace. 5 Only use the machine as it was intended. If damage or any unauthorized variation from factory delivered condition is discovered, the machine must be tagged and removed from service. Repairs to the machine may only be made by a qualified service technician, according to the manufacturer’s specifications. After repairs are completed, the operator must perform a pre-operation inspection again before going on to the function tests. Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer’s specifications and the requirements listed in the responsibilities manual. 22 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Inspections Limit switches Pre-operation Inspection Steer and axle sensors Be sure that the operator’s and safety manuals are complete, legible and in the storage container located in the cab. Be sure that all decals are legible and in place. See Inspections section. Lights, alarms and beacons (if equipped) Pins, nuts, bolts and other fasteners Check entire machine for: Cracks in welds or structural components Check for hydraulic oil leaks and proper oil level. Add oil if needed. See Maintenance section. Dents or damage to machine Excessive rust, corrosion or oxidation Check for battery fluid leaks and proper fluid level. Add distilled water if needed. See Maintenance section. Check the transmission oil level. Add oil if needed. See Maintenance section. Be sure that all structural and other critical components are present and all associated fasteners and pins are in place and properly tightened. Check for engine oil leaks and proper oil level. Add oil if needed. See Maintenance section. Be sure the windshield and windows (if equipped) are clean and free of obstructions that might limit visibility. Air-filled tires models: Check for proper tire pressure. Add air if needed. See Maintenance section. After you complete your inspection, be sure that all guards, screens and compartment covers are in place and secured. Check the following components or areas for damage, improperly installed or missing parts and unauthorized modifications: Electrical components, wiring and electrical cables Hydraulic hoses, fittings, cylinders and manifolds Fuel and hydraulic tanks Drive motors and drive hubs Boom wear pads Tires and wheels Engine and related components Part No. 237108 GTH-844 23 Operator's Manual Third Edition • Sixth Printing Inspections Function Test Fundamentals The function tests are designed to discover any malfunctions before the machine is put into service. The operator must follow the step-by-step instructions to test all machine functions. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. A malfunctioning machine must never be used. If malfunctions are discovered, the machine must be tagged and removed from service. Repairs to the machine may only be made by a qualified service technician, according to the manufacturer’s specifications. After repairs are completed, the operator must perform a pre-operation inspection and function tests again before putting the machine into service. 3 Always perform function tests prior to use. Know and understand the function tests before going on to the next section. 4 Inspect the workplace. 5 Only use the machine as it was intended. 24 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Inspections Function Tests 1 Select a test area that is firm, level and free of obstruction. Be sure there is no load on the forks or attachment. 2 Enter the cab and sit on the seat. 3 Adjust the seat and steering column, if needed. 4 Fasten the seat belt. 5 Adjust the mirrors, if required. 6 Be sure the parking brake is on and the transmission control is in neutral. 7 Start the engine. See Starting the Engine in the Operating Instructions section. Test the Dual Control Handles (if equipped) 11 Using the boom control handle, momentarily raise the boom, extend the boom, retract the boom and lower the boom. Result: All functions should operate smoothly. 12 Using the tilt and sway control handle, momentarily tilt the forks up and tilt the forks down. Result: All functions should operate smoothly. 13 Using the tilt and sway control handle, momentarily sway the machine to the right and to the left. Result: All functions should operate smoothly. Test the Single Control Handle (if equipped) 8 Using the control handle, momentarily raise the boom, extend the boom, retract the boom and lower the boom. Result: All functions should operate smoothly. 9 Using the control handle and the red thumb switch, momentarily tilt the forks up and tilt the forks down. Result: All functions should operate smoothly. 10 Using the control handle and the white finger switch, momentarily sway the machine to the right and to the left. Result: The frame level function should operate smoothly. Part No. 237108 GTH-844 25 Operator's Manual Third Edition • Sixth Printing Inspections Test the Steering 14 Push the right side of the steer selector switch to select four-wheel steer. The four-wheel steer indicator light on the instrument panel will be on. 20 Push the left side of the steer selector switch to select crab steer. The crab steer indicator light on the instrument panel will be on. 21 Check the steering operation by turning the steering wheel approximately ¼ turn in each direction. 15 Check the steering operation by turning the steering wheel approximately ¼ turn in each direction. Result: The front wheels should turn in the same direction as the steering wheel. The rear wheels should turn in the opposite direction. 16 Straighten the wheels. Test the Transmission and Brakes 22 Be sure the boom is fully lowered and retracted. 23 Step on the brake pedal. Push the bottom of the parking brake switch to turn it off. 17 Push the steer selector switch to the middle position to select two-wheel steer. The two-wheel steer indicator light on the instrument panel will be on. 18 Check the steering operation by turning the steering wheel approximately ¼ turn in each direction. Result: The front wheels should turn in the same direction as the steering wheel. The rear wheels should not turn. 19 Straighten the wheels. Result: The front wheels and the rear wheels should turn in the same direction as the steering wheel. 24 Move the transmission control lever to forward. Slowly let up on the brake pedal. As soon as the machine starts to move, push the brake pedal. Result: The machine should move forward, and then come to an abrupt stop. 25 Move the transmission control lever to reverse. Slowly let up on the brake pedal. As soon as the machine starts to move, push the brake pedal. Result: The machine should move in reverse, and then come to an abrupt stop. The back-up alarm should sound when the transmission control lever is in reverse. 26 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Inspections 26 Move the transmission control lever to neutral. Test the Lights (if equipped) 27 Push the top of the parking brake switch. Result: The red parking brake indicator light should come on, indicating the parking brake is on. 28 Move the transmission control lever forward, and then in reverse. Result: The machine should not move. 35 Verify that all lights are functional. Test the 2-speed Transmission (if equipped) 36 Retract and lower the boom to the stowed position. 37 Drive the machine forward. Rotate the control lever to shift the transmission to second gear. Test the Drive and Sway Cutout Result: The machine should shift to second gear. 29 Raise the boom to 55°. Do not extend the boom. 30 Step on the brake pedal. 38 Rotate the control lever to shift the transmission to third gear. 31 Push the bottom of the parking brake switch. The parking brake is off when the indicator light is off. 39 Result: The transmission should not shift to third gear. 32 Put the transmission control lever in forward. Slowly let up on the brake pedal. Result: The drive function should not operate. 33 Put the transmission control lever in neutral. 34 Push the top of the parking brake switch. Slowly sway the machine to the left and to the right. Result: The sway function should not operate. Part No. 237108 GTH-844 27 Operator's Manual Third Edition • Sixth Printing Inspections Workplace Inspection Checklist Be aware of and avoid the following hazardous situations: drop-offs or holes bumps, floor obstructions or debris Do Not Operate Unless: sloped surfaces You learn and practice the principles of safe unstable or slippery surfaces machine operation contained in this operator’s manual. overhead obstructions and high voltage conductors 1 Avoid hazardous situations. hazardous locations 2 Always perform a pre-operation inspection. inadequate surface support to withstand all load forces imposed by the machine 3 Always perform function tests prior to use. wind and weather conditions 4 Inspect the workplace. the presence of unauthorized personnel Know and understand the workplace inspection before going on to the next section. other possible unsafe conditions 5 Only use the machine as it was intended. Workplace Inspection Fundamentals The workplace inspection helps the operator determine if the workplace is suitable for safe machine operation. It should be performed by the operator prior to moving the machine to the workplace. It is the operator’s responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine. 28 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Inspections Inspection for Decals with Words Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No. Decal Description Qty Part No. Decal Description Qty 219703 Cosmetic – Genie GTH-844, Small 1 219626 Label – Genie Logo 1 220271 Label – Boom Lettering 1 236083 Cosmetic – Genie GTH-844 2 237598 Warning – Crush Hazard, Moving Machine 3 28159 Label – Diesel 1 237599 Warning – Bodily Injury Hazard 1 28175 Warning – Compartment Access 1 237600 Notice – Axle Differential Lock 1 82366 Label – Chevron Rando 1 237601 Danger – Explosion/Burn Hazard 1 82558 Warning – Skin Injection Hazard 1 237605 Warning – Burn Hazard, Hot Parts 1 97602 Warning – Explosion Hazard 1 237606 Label – Single Controller 1 97667 Warning – Burn Hazard 1 237684 1 114090 Label – Transmission Control 1 Label - Load Chart, Standard Carriage 114115 Label – Steer Model Selector 1 237863 Label – Angle Indicator 1 133206 Label – Emergency Exit 1 237970 Warning – Crush Hazard, Tires 3 237971 Danger – Explosion/Burn Hazard, Fueling 1 826345 Label – Ultra Low Sulfur Fuel Only (diesel models) 1 822590 Label – 2-speed Transmission 1 160482 Label – Transport and Lifting 1 214418 Danger/Warning – 2 Decal Combination 3 214419 Danger/Warning – 6 Decal Combination 1 215267 Label – Product Registration 1 1253091 Label – Key Ignition 1 Warning – Fall Hazard, Work Platform 1 1257919 Label – Load Chart, Quick Attach Lifting Point 1 215384 Label – FOPS/ROPS 1 1257994 Cosmetic – Genie 1 215652 Label – Dual Controller 1 1261896 Label – Load Chart, Swing 1 216208 Label - LED Chart 1 1262614 Warning – Tip-over, Swing Carriage 2 219648 Label – Load Chart, Rotate Carriage 1 215268 Part No. 237108 GTH-844 29 Operator's Manual Third Edition • Sixth Printing Inspections 1253091 load chart set 214418 133206 214419 215652 237606 114090 822590 215384 114115 237600 216208 237599 236083 97602 237605 237601 82558 215268 237598 214418 237598 219703 237970 1257994 214418 97667 28175 236083 82366 220271 Serial Label 215267 237598 160482 826345 28159 237971 237970 1262614 Shading indicates decal is hidden from view, i.e. under covers 30 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Inspections Inspection for Decals with Symbols Part No. Decal Description Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No. Decal Description Qty 219703 Cosmetic – Genie GTH-844, Small 1 220271 Label – Boom Lettering 1 236083 Cosmetic – Genie GTH-844 2 237606 Label – Single Controller 1 237720 Label – Crush Hazard, Moving Machine 3 Qty 237721 Label – Bodily Injury Hazard 1 Label – Diesel 1 237722 Label – Explosion/Burn Hazard 1 82473 Label – Compartment Access 1 237726 Label – Skin Injection Hazard 1 Label – Burn Hazard, Hot Components 1 82560 133031 Label – Burn Hazard 1 237863 Label – Angle Indicator 1 237684 Label - Load Chart, Standard Carriage 1 822590 Label – 2-speed Transmission 1 28159 114090 Label – Transmission Control 1 114115 Label – Steer Model Selector 1 133206 Label – Emergency Exit 1 160482 Label – Transport and Lifting 1 215644 Label – Crush Hazard, Tires 1253091 Label – Key Ignition 1 3 1257919 Label – Load Chart, Quick Attach Lifting Point 1 215645 Label – Explosion/Burn Hazard 1 1257994 Cosmetic – Genie 1 215646 Label – 2 Decal Combination 3 1261896 Label – Load Chart, Swing 1 215647 Label – 6 Decal Combination 1 1262615 Label – Tip-over, Swing Carriage 2 215648 Label – Fall Hazard 1 215652 Label – Dual Controller 1 219648 Label – Load Chart, Rotate Carriage 1 Part No. 237108 GTH-844 31 Operator's Manual Third Edition • Sixth Printing Inspections 1253091 load chart set 215646 133206 215652 237606 114090 822590 215647 1253091 A 114115 237721 236083 237726 237722 82560 215648 237720 215646 237720 219703 215644 215646 1257994 133031 82473 236083 Serial Label 220271 237720 160482 215645 28159 215644 1262615 Shading indicates decal is hidden from view, i.e. under covers 32 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Operating Instructions Fundamentals The Operating Instructions section provides instructions for each aspect of machine operation. It is the operator’s responsibility to follow all the safety rules and instructions in the operator’s, safety and responsibilities manuals. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator’s manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. 5 Only use the machine as it was intended. Part No. 237108 A variable reach rough terrain forklift truck is defined as a wheeled type truck designated primarily as a fork truck with a pivoted boom, which may be equipped with attachments for lifting material. Using it for any other use is unsafe and dangerous. Only trained and authorized personnel should be permitted to operate a machine. If more than one operator is expected to use a machine at different times in the same work shift, they must all be qualified operators and are all expected to follow all safety rules and instructions in the operator’s, safety and responsibilities manuals. That means every new operator should perform a pre-operation inspection, function tests, and a workplace inspection before using the machine. GTH-844 33 Operator's Manual Third Edition • Sixth Printing Operating Instructions Parking Brake Steer Select Use the parking brake switch to apply the parking brake before raising the boom or leaving the machine. Always position all wheels in line with the machine before switching the steering mode. Push the top of the rocker switch to turn the parking brake on. Do not realign the wheels while driving. Steer selector switch Push the bottom of the switch to turn the parking brake off. Brake Pedal Use the brake pedal to control the machine speed and to stop the machine motion. Push and hold the brake pedal to stop the machine. Push and release the brake pedal to control the machine speed. Emergency Exit (if equipped) Rotate each retaining lever and push out the window. Starting the Engine 1 Be sure the parking brake is set and the transmission control lever is in the neutral position. 2 Insert the key in the ignition switch. 3 Turn the key until the engine starts. If the engine fails to start after 30 seconds of cranking, determine the cause and repair any malfunction. Wait 120 seconds before trying to start again. 34 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Transmission Control Models with 3-speed transmission Use the transmission control lever to control the speed and direction of machine travel. Step on the service brake pedal before putting the transmission into gear. To drive forward, move the transmission control lever toward you and move it up. To drive in reverse, move the transmission control lever toward you and move it down. To return to neutral, move the transmission control lever to the center position. Come to a complete stop before shifting the transmission from forward to reverse. The transmission control lever must be in 1st or 2nd gear only. Forward / 1st gear: Low speed / high torque Forward / 2nd gear: Medium speed / medium torque Forward / 3rd gear: High speed / low torque The transmission control lever also controls the transmission speed. To choose a lower speed, rotate the control lever clockwise. To choose a higher speed, rotate the control lever counterclockwise. Part No. 237108 GTH-844 35 Operator's Manual Third Edition • Sixth Printing Operating Instructions Frame Sway Control Models with 2-speed transmission Before raising the boom, the machine must be level. 1 Check the left to right level indicator. The left to right level indicator should be 0 degrees before raising the boom. 2 If the machine is not level, use the frame sway control function to level the machine. Only use the frame sway control function if the boom angle indicator is at 0 degrees or less. Come to a complete stop before shifting the transmission from forward to reverse. The transmission control lever must be in 1st or 2nd gear only. See Controller Movements section. Transporting a Load Forward / 1st gear: Low speed / high torque Center the load on the forks. Position the load so that it is completely against the back of the fork frame. Forward / 2nd gear: Medium speed / medium torque Axle Differential Lock Use the axle differential lock switch to lock the axle differential and gain added traction in certain types of terrain such as sand, mud or snow. Come to a complete stop before activating the axle differential lock. Do not lock the axle when the machine is moving. The load should be kept as low to the ground as possible while traveling. Always move a loaded machine with the boom angle indicator at 0 degrees or less. Tilt the forks back slightly to help keep the load secure. Always bring the machine to a complete stop before applying the parking brake. Step on the pedal and hold it to activate the axle differential lock. Release the pedal to release the differential lock. 36 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Raising and Placing a Load The load chart in the cab shows the operating limits of a properly maintained and operated machine. To use the load chart, the operator must know the weight of the load, its load center and how far out and up it is to be placed. This machine has more than one load chart. Be sure you are using the load chart that corresponds to the attachment on the machine. If you determine that the weight of the load cannot be placed at the height and angle you want, these options can be used: 1 Move the machine closer to the loading or pick point so that the weight of the load will meet the load chart specifications. 2 Divide the load into smaller pieces so that each piece meets the load chart specifications. 3 Obtain a larger machine capable of handling the load within specifications. Placing the load 1 Travel to the desired work site and carefully stop the machine. 2 Put the transmission in neutral. 3 Apply the parking brake. 4 Level the frame, if the left to right level indicator or the front to back level indicator is not at 0 degrees. 5 Gradually move the controller to raise and extend the boom to the required height. Part No. 237108 GTH-844 37 Operator's Manual Third Edition • Sixth Printing Operating Instructions 6 Gradually move the controller to lower and extend the boom into final position. Lower the load until the weight is completely off the forks. Do not apply a downward force with the forks. 7 Gradually move the controller to raise and retract the boom. This will bring the forks out of the load. 38 8 GTH-844 When the forks are clear of the load and the structure, the boom can be lowered and retracted. Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Controller movements – Single Control Handle Control handle only Control handle with red thumb switch (A) Control handle with white finger switch (B) Controller movements - Dual Control Handle Boom control handle Part No. 237108 Tilt and sway control handle GTH-844 39 Operator's Manual Third Edition • Sixth Printing Operating Instructions Rear Axle Lock If the boom is raised above 55°, the transmission will shift to neutral and the frame sway function will not operate. Boom and fork functions continue to operate. To unlock the rear axle and to operate the frame sway function, lower the boom. When the boom is at or below 0°, the frame sway function will operate. 40 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Quick Attach Instructions Remove the quick attach lock pin. Tilt the forks forward to pivot the quick attach connector back. Position the boom so that the quick attach pin on the boom is below and centered between the hooks on the attachment. a a b c d e Raise the boom until the pin is secured in the hooks on the attachment. b c d e quick attach pin quick attach lock pin quick attach lock lever quick attach connector attachment hooks Engine Condition Indicator Tilt the forks back to pivot the quick attach into the attachment. If the engine diagnostic display indicates an engine fault, contact service personnel. Insert the quick attach lock pin all the way through the attachment and be sure the quick attach lock lever is secured in the notch on the pin. Part No. 237108 GTH-844 41 Operator's Manual Third Edition • Sixth Printing Operating Instructions After Each Use 1 2 To jump start the machine Select a safe parking location—firm level surface, clear of obstruction and traffic. Retract and lower the boom to the stowed position. 1 Connect the positive (+) jumper cable to the positive (+) post of the discharged battery. 2 Connect the other end of the same jumper cable to the positive (+) post of the booster battery. 3 Move the transmission control lever to neutral. 4 Set the parking brake. 3 5 Turn the key switch to the off position and remove the key to secure from unauthorized use. Connect one end of the second jumper cable to the negative (-) post of the booster battery. 4 Make the final cable connection to the engine block or the furthest ground point away from the battery. 5 Start the engine. Jump Starting the Machine Jump starting at the battery or battery replacement is required when the battery is discharged to the point where the battery will not crank the starter. Never jump start the machine directly to the starter or the starter solenoid. Serious injury or death could result from the machine moving forward or backward. To avoid personal injury when jump starting with another machine, be certain that the machines are not touching. Never jump start a frozen battery as it will explode. Keep sparks and flames away from the battery. Lead acid batteries generate explosive gases when charging. Wear safety glasses when working near batteries. The booster battery must be 12V. The machine used for jump starting must have a negative ground electrical system. 42 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Operating Instructions Driving on a slope Additionally, tip over of a machine is dependent in large part upon operator inputs such as the speed and smoothness of the operation as well as the position of the attachment and its load. When the machine is loaded, always travel with the load uphill. When the machine is unloaded, travel with the forks or attachment downhill. Construction sites and roads will frequently change slope from place to place, can be hard and soft, and change due to the construction activities and weather. On steep terrain, drive only up and down hill, and always keep the machine in gear. Do not turn across slope when machine is traveling up or down a slope. To avoid overspeeding the engine and transmission when driving down slopes, downshift to a lower gear and use the service brake as necessary to maintain a slow speed. Operators should be properly trained and use their best judgment and experience to take the necessary precautions to prevent tip over. Operators must assess the jobsite variables and avoid exceeding the machine's (or operator's) capabilities for terrain and conditions. Limit travel path and speed according to the condition of the ground surface, traction, slope, location of personnel and any other factors which may create a hazard. Never drive the machine unless the mast and equipment are in their proper travel position. Whether a machine will tip over during dynamic machine operation involves many variables that need to be considered. Among these are pavement/ground conditions, stability and slope, as well as machine equipment, operator skill, load position, tire inflation, machine speed, etc. Part No. 237108 GTH-844 43 Operator's Manual Third Edition • Sixth Printing Transport and Lifting Instructions Transport and Lifting Instructions Before loading for transport, make sure the deck, ramps and machine tires are free of mud, snow and ice. Failure to do so could cause the machine to slide. Be sure the vehicle capacity, loading surfaces Observe and Obey: Genie provides this securement information as a recommendation. Drivers are solely responsible for making sure machines are properly secured and the correct trailer is selected pursuant to US Department of Transportation regulations, other localized regulations, and their company policy. and chains or straps are sufficient to withstand the machine weight. Genie telehandlers are very heavy relative to their size. See the serial label for the machine weight. See the Inspections section for the serial label location. Genie customers needing to containerize any lift or Genie product should source a qualified freight forwarder with expertise in preparing, loading and securing construction and lifting equipment for international shipment. Only qualified operators should move the machine on or off the truck. The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded. 44 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Transport and Lifting Instructions Securing to Truck or Trailer for Transit Turn the key switch to the off position and remove the key before transporting. Inspect the entire machine for loose or unsecured items. Securing the Chassis Use chains of ample load capacity. Use a minimum of 6 chains. There are 6 tie down points on the chassis, two in the front and two on each side of the machine. Be sure the door and the door windows are latched and secured (if equipped). Fully lower the forks or attachment onto the truck bed. Secure the forks or attachment with a suitable strap or chain to prevent movement. Prior to loading, level the telehandler and retract the boom. Adjust the rigging to prevent damage to the chains. Use a spotter to load and unload the telehandler. Keep the boom as low as possible when loading and unloading. Set the parking brake. 44 in / 1.1 m 102 in / 2.6 m Part No. 237108 GTH-844 45 Operator's Manual Third Edition • Sixth Printing Transport and Lifting Instructions Lifting Instructions Fully lower and retract the boom. Determine the center of gravity of your machine using the picture on this page. Remove all loose items on the machine. Observe and Obey: Only qualified riggers should rig the machine. Only certified crane operators should lift the Attach the rigging only to the designated lifting points on the machine. Adjust the rigging to prevent damage to the machine and to keep the machine level. machine and only in accordance with the applicable crane regulations. Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight. See the serial label for the machine weight. 44 in / 1.1 m 102 in / 2.6 m 46 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Maintenance Maintenance Check the Engine Oil Level Observe and Obey: Maintaining the proper engine oil level is essential to good engine performance and service life. Operating the machine with an improper oil level can damage engine components. Only routine maintenance items specified in Note: Check the oil level with the engine off. this manual shall be performed by the operator. 1 Scheduled maintenance inspections shall be completed by qualified service technicians, according to the manufacturer’s specifications and the requirements specified in the responsibilities manual. Check the oil level dipstick. Add oil as needed. Perkins 1104D-E44T Engine Oil type 15W-40 Perkins 854E-E34TA Engine Oil type API CJ-4 15W-40 Low Ash Oil Deutz TCD 3.6 L4 Tier 3 Engine Maintenance Symbols Legend Oil type The following symbols have been used in this manual to help communicate the intent of the instructions. When one or more of the symbols appear at the beginning of a maintenance procedure, it conveys the meaning below. 15W-40 Deutz TCD 3.6 L4 Tier 4i Engine Oil type API CJ-4 15W-40 Low Ash Oil Indicates that tools will be required to perform this procedure. Indicates that new parts will be required to perform this procedure. Indicates that a cold engine is required before performing this procedure. Part No. 237108 GTH-844 47 Operator's Manual Third Edition • Sixth Printing Maintenance Diesel Fuel Requirements Check the Hydraulic Oil Level Satisfactory engine performance is dependent on the use of a good quality fuel. The use of a good quality fuel will give the following result: long engine life and acceptable exhaust emissions levels. Maintaining the hydraulic oil at the proper level is essential to machine operation. Improper hydraulic oil levels can damage hydraulic components. Daily checks allow the inspector to identify changes in oil level that might indicate the presence of hydraulic system problems. Minimum diesel fuel requirements for each engine are listed below. Perkins 1104D-E44T Engine Fuel Type Low Sulfur Diesel (LSD) 1 Be sure that the engine is off, the frame is level and the boom is in the stowed position. 2 Visually inspect the sight gauge located on the side of the hydraulic oil tank. Perkins 854E-E34TA Engine Fuel Type Deutz TCD 3.6 L4 Tier 3 Engine Fuel Type 3 48 Add oil as needed. Do not overfill. Low Sulfur Diesel (LSD) Deutz TCD 3.6 L4 Tier 4i Engine Fuel Type Result: The hydraulic oil level should be halfway in the sight gauge. Ultra Low Sulfur Diesel (ULSD) Hydraulic oil specifications Ultra Low Sulfur Diesel (ULSD) Hydraulic oil type GTH-844 Chevron Rando HD equivalent Part No. 237108 Third Edition • Sixth Printing Operator's Manual Maintenance Check the Engine Coolant Level – Liquid Cooled Models Check the Batteries Proper battery condition is essential to good machine performance and operational safety. Improper fluid levels or damaged cables and connections can result in component damage and hazardous conditions. Electrocution hazard. Contact with hot or live circuits may result in death or serious injury. Remove all rings, watches and other jewelry. Bodily injury hazard. Batteries contain acid. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. 1 Put on protective clothing and eye wear. 2 Be sure that the battery cable connections are tight and free of corrosion. 3 Be sure that the battery hold-down brackets are in place and secure. Maintaining the engine coolant at the proper level is essential to engine service life. Improper coolant level will affect the engine’s cooling capability and damage engine components. Daily checks will allow the inspector to identify changes in coolant level that might indicate cooling system problems. Perkins Engines: 1 Check the fluid level in the radiator. Result: The fluid level should be at the bottom of the filler neck. Bodily Injury Hazard. Fluids in the radiator are under pressure and extremely hot. Use caution when removing cap and adding fluids. Deutz Engines: Note: Adding terminal protectors and a corrosion preventative sealant will help eliminate the corrosion on the battery terminals and cables. 1 Check the fluid level in the sight glass located on the radiator expansion tank. Result: The fluid level should be at the half way mark of the sight glass when the engine is cold. Coolant Specification Perkins and Deutz engines Part No. 237108 GTH-844 Extended Life Coolant (ELC) 49 Operator's Manual Third Edition • Sixth Printing Maintenance Check the Tire Pressure Scheduled Maintenance Maintenance performed quarterly, annually and every two years must be completed by a person trained and qualified to perform maintenance on this machine according to the procedures found in the service manual for this machine. Tip-over hazard. An over-inflated tire can explode which may compromise machine stability and cause the machine to tip over. Tip-over hazard. The use of temporary flat tire repair products may lead to tire failure which could compromise machine stability and cause the machine to tip over. Machines that have been out of service for more than three months must receive the quarterly inspection before they are put back into service. Bodily injury hazard. An over-inflated tire can explode and may cause death or serious injury. Note: This procedure does not need to be performed on machines equipped with foam-filled tires. 1 Check each tire with an air pressure gauge. Add air as needed. Tire pressure 50 62 psi 4.3 bar GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments Attachments Work Platform Hazards Always perform a pre-operation inspection of the platform, per the manufacturer’s instructions, prior to use. Work Area Safety If damage or any unauthorized variation from factory delivered condition is discovered, the platform must be tagged and removed from service. The telehandler shall not be used to lift people unless there is no other practical option. If a telehandler must be used to lift people, the following precautions for the protection of occupants shall be taken. Do not modify the platform without written approval by Genie and the platform manufacturer. Use only a Genie approved personnel work platform which complies with the design requirements of ANSI/ITSDF B56.6. Do not lift personnel with a telehandler unless it is equipped with an approved work platform. The user or employer and the operator shall further investigate, and comply with, all applicable jobsite, local, state, provincial, or federal rules, regulations, and standards related to the use of the telehandler with a work platform. Do not use the telehandler with a work platform attached for any purpose other than positioning personnel with their tools, materials and equipment. Provide overhead protection as required by the operating conditions. Platform Occupant Fall Protection Personal fall protection equipment (PFPE) is required for all occupants of the work platform. Read, understand and obey all warnings and instructions provided with the attachment that is approved for elevating personnel. Occupants must wear a safety belt or harness in accordance with governmental regulations. Attach the lanyard to the anchor provided in the platform. The operator and the platform occupants must be instructed regarding the specific hazards associated with using the telehandler with the work platform, and utilize all means, including those provided by the user or employer, to avoid them. All PFPE must comply with applicable governmental regulations, and must be inspected and used in accordance with the PFPE manufacturer’s instructions. Part No. 237108 GTH-844 51 Operator's Manual Third Edition • Sixth Printing Attachments Do not place or attach overhanging loads to any part of this machine or platform. Occupying the Platform Do not place ladders or scaffolds in the platform or against any part of this machine. Do not carry materials directly on platform railing unless approved by Genie. Be certain that materials and tools are protected from falling out of the platform. Be aware of crushing hazards when grasping the platform guard rail. During movement of the platform, occupants must keep all body parts inside the platform railing. Do not sit, stand or climb on the platform guard rails. Maintain a firm footing on the platform floor at all times. Do not tie the boom or platform to adjacent structures. Do not place loads outside the platform perimeter. Do not transport tools and materials unless they are evenly distributed and can be safely handled by person(s) in the platform. Keep the platform floor clear of debris. Never use ladders, boxes, steps, planks or similar items on the platform to provide additional reach. Be certain that required personnel fall protection devices, such as guard rails and full body harness with lanyard, are in place and properly used. Do not enter or exit the platform unless the machine is in the stowed position and the platform is at ground level. Occupants shall not climb on any part of the telehandler in attempting to enter and exit the platform. Use the hand rails to maintain balance while the platform is in motion. Do not increase the surface area of the platform or the load. Increasing the area exposed to the wind will decrease machine stability. Do not climb down from the platform when raised. 52 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments Telehandler Operation Lifting Personnel Be certain that the platform is securely attached to the telehandler, lifting carriage and forks. Occupants, equipment and materials shall not exceed the maximum platform capacity. Distribute loads evenly on the platform floor. Be certain that the lifting carriage and forks are secured to prevent them from pivoting freely. Do not drive the telehandler when occupants are in the platform. The combined weight of the platform, load, and personnel shall not exceed one-third of the capacity at the related load center position (24 inches / 60 cm) as indicated on the load charts of the telehandler on which the platform is used. Always fully lower the platform and have occupants leave the platform before driving the telehandler. Be certain that the path of platform travel is clear of hazards such as storage racks, scaffolds, overhead obstructions, and electrical wires. Before elevating personnel, the area shall be marked to warn of work by elevated personnel. Do not level the machine with the frame sway function when the platform is occupied. Prior to lifting personnel, platform occupants and telehandler operator must establish a means of communication for positioning of the platform. Be sure that operators of other overhead and floor level machines are aware of the machine’s presence. Be certain that the platform is horizontal before lifting, and do not tilt the platform forward or backward when the occupied platform is elevated. When equipped, always lower the stabilizers prior to raising personnel. Part No. 237108 GTH-844 53 Operator's Manual Third Edition • Sixth Printing Attachments Keep bystanders away while operating. Do not place boom or platform against any structure to steady the platform or to support the structure. Operating Instructions Do not use the controls to free a platform that is caught, snagged or otherwise prevented from normal motion by an adjacent structure. All personnel must be removed from the platform before attempting to free the platform using the controls. Read, understand and obey all jobsite, local, state, federal and provincial rules, standards and regulations as they pertain to the use of a telehandler mounted personnel work platform (In the USA and Canada, reference ANSI/ITSDF B56.6 and CSA B335). Check the work area for overhead obstructions or other possible hazards. Preparation and Setup If the personnel work platform is equipped with safety instructions, make sure a copy is placed in the cab as well as in the work platform, if it is equipped with a manual holder. Cordon off the area to warn of work by elevated personnel. Keep the area under the platform free of personnel. Be certain that the path of platform travel is clear of hazards, such as storage racks, scaffolds, overhead obstructions, and electrical wires. Do not allow personnel or bystanders to tamper with or operate the machine from the cab when occupants are in the platform except in an emergency or when directed by the occupants. Be sure the telehandler is on a firm level surface capable of supporting all forces imposed by the machine. Without personnel in the platform, perform a simulated lift with the designated signal person on the ground as a spotter, to assure adequate telehandler range and attachment clearances and that the telehandler lifting mechanism is operating smoothly. Always lift and lower personnel smoothly and with caution, and only at their request. 54 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments Installing and securing the platform Lifting and lowering the platform Set the parking brake and place the transmission into neutral. Center the platform on the telehandler. If equipped with stabilizers: Lower the stabilizers. Properly secure the platform to the telehandler according to the manufacturer’s instructions. Be sure that the forks supporting the platform are secured to prevent them from pivoting forward. If mounted to a rotating attachment, center the rotation of the attachment and then deactivate its rotation capability. Level the platform, both side to side (frame sway function) and front to rear (attachment tilt function). Only allow personnel to enter and exit the platform when it is at ground level. Establish and maintain a means of communication with the occupants. Only move the platform at the request of a single designated occupant. Never tilt the platform forward or backward, or attempt to level the machine when the platform is occupied. Sound the horn to alert occupants prior to lifting or lowering the platform. Entering, occupying and exiting the platform Move the platform slowly, smoothly and with caution. Use three-point contact when entering or exiting a work platform. Only enter and exit the platform when it is at ground level. Only enter and exit the platform at the designated entry and exit locations. Keep hands and feet clear of all controls other than those in use. When the platform is occupied, the telehandler operator must remain seated in the cab with the occupants in direct line of sight. Close and secure the entry point gate or railing before signaling to be lifted. Attach PFPE to the designated lanyard anchor. Occupants should use the guardrail to help stabilize themselves during movement. Be aware of crushing hazards when grasping the platform guardrail. Part No. 237108 GTH-844 55 Operator's Manual Third Edition • Sixth Printing Attachments Suspended Load Hazards Overturning Hazards Work Area Safety Do not lift a suspended load without the proper and legible load capacity chart for the attachment/telehandler combination you are using. General Safety Do not lift a suspended load without first understanding the local, state, federal, or provincial rules, standards and regulations related to the activity. In the USA requirements are set forth in ANSI/ITSDF B56.6 and OSHA 29 CFR 1926.1400-1442. Additional rules, standard and regulations may apply. Additional training may be required. Do not permit the load to swing freely. Always properly tether loads to restrict movement. In addition to ground personnel, the two chassis tie-down points in the front of the machine can be used to help externally stabilize the load. Always cross the tethers to opposite sides of the load to minimize load movement. Driving across grades, sudden starts, stops, and turns can cause the load to swing and create a hazard if not externally stabilized. If a telehandler must be used to transport a suspended load, the following precautions for the protection of the operator shall be taken. Read, understand and obey all warnings and instructions provided with the attachment that is approved for suspending loads. Only properly designed, tested and approved attachments, designated lifting points, and lifting accessories should be used to support a suspended load. The telehandler load charts are designed for loads where the load center is stationary. As a suspended load moves, the load center can change. As a result, extreme caution in transporting and lifting, or placing, the load must be observed to minimize the potential for the load to move. Keep the boom retracted as much as practical. Do not lift suspended loads when wind speeds can cause an unsafe situation. 56 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments All movements of the load must be accomplished gradually and at the slowest practical speed to prevent the load from swinging. Keep the heavy part of the load closest to the attachment. Do not leave the telehandler unattended with a suspended load. Keep the boom and load as low as practical while maintaining visibility in the direction of travel. Do not exceed walking speed (2 mph / 3.2 km/h) with a suspended load. Never drag or pull a load sideways. Only lift a load vertically; do not pull a load horizontally as it could cause excessive swinging of the load. Start, travel, turn and stop slowly to prevent the load from becoming unstable or swinging. The weight of all rigging (slings, shackles etc.) must be included as part of the load. Do not use any controls to re-position the load when traveling. Come to a gradual and complete stop before attempting to re-position the load. Identify the proper lifting points of the load, taking into consideration the center of gravity and load stability. Do not attempt to cross inclines as the load center will move towards the tipping line, thereby reducing stability. Do not attempt to use the telehandler frame-leveling to compensate for a swinging load or to adjust the load after it has been raised. Only climb or descend inclines with extreme care as the load center will move towards the tipping line, thereby reducing stability Do not try to move fixed or obstructed loads. Do not park on a slope. Fall Hazards Do not lift or suspend personnel. Part No. 237108 GTH-844 57 Operator's Manual Third Edition • Sixth Printing Attachments Collision Hazards Lifting a Suspended Load Be sure that the load is clear of any adjacent obstacles before lifting. Verify that landing point is level and can safely support the load. When visibility is or could be obstructed, near or at the load placement, the operator shall use alternative or additional means to safely lift the load, such as a qualified signal person. Properly secure the attachment to the telehandler Signal persons must remain in constant communication (verbal or hand) and be in visual contact with the operator at all times. Level the frame on the telehandler. Rig the load as outlined in OSHA 29 CFR 1926.1401, 1926.1404, 1926.1425, keeping the heaviest part of the load as close to the attachment as practical. Tether the load to restrict movement. Crush Hazards Ask a signal person to assist with lifting the load if visibility will be obstructed at the point of operation. Never allow the signal person to come between the suspended load and another object (such as the telehandler itself). Make sure that the signal person remains in constant communication and is in visual contact at all times. Falling Object Hazards With the boom retracted as far as practical, slowly and gradually raise the boom and load, making sure to keep the load and boom as low to the ground as practical. Do not raise the load into the fall zone shown. Be sure that all boom and attachment movements are performed as slow as practical to avoid swinging of the load. Do not operate the machine while people are under the load or in the fall zone. Do not suspend loads using slings or chains from the forks or fork carriage. Avoid lifting double tiered loads. 58 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments Traveling Placing the Load Be sure that the path of travel is level and capable of supporting the telehandler with its load. Ask a signal person to assist with placing the load if visibility will be obstructed at the point of operation. Keep the boom, and load, as low as practical while maintaining visibility in the direction of travel. Ask a signal person to assist with your travel if visibility will be obstructed in the direction of travel. Crush or Collision Hazard. Make sure that the signal person remains in constant communication and be in visual contact at all times. Only make adjustments to the load after bringing the telehandler to a complete stop. Start, stop, travel and turn slowly to prevent the load from becoming unstable or swinging. Do not travel faster than walking speed (<2 mph / 3.2 km/h). Part No. 237108 Make sure that the signal person remains in constant communication and be in visual contact at all times. Come to a complete stop near the landing point. If equipped with stabilizers: Lower the stabilizers. Set the parking brake and place the transmission into neutral. Slowly, and gradually, place the load over the landing point and lower the load until it is safely supported. Once the load has been landed, continue to lower the boom until the rigging and tethers can be removed. GTH-844 59 Operator's Manual Third Edition • Sixth Printing Attachments Signal Person (from 1926.1419) Per OSHA CFR 1926.1419, a signal person is required when: The point of operation, meaning the load travel or the area near or at load placement, is not in full view of the operator. When the equipment is traveling, the view in the direction of travel is obstructed. Due to site specific safety concerns, either the operator or the person handling the load determines that it is necessary. Signal persons must remain in constant communication (verbal or hand) and be in visual contact with the operator at all times. When using hand signals, follow the requirements set forth in OSHA CFR 1926.1419-1926.1422. The hand signal chart below may be used in place of the Standard Method in Appendix A of Subpart CC of Part OSHA CFR 1926. 60 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Attachments STOP. With arm extended horizontally to the side, palm down, arm is swung back and forth. EMERGENCY STOP. With both arms extended horizontally to the side, palms down, arms are swung back and forth. HOIST. With upper arm extended to the side, forearm and index finger pointing straight up, hand and finger make small circles. RAISE BOOM. With arm extended horizontally to the side, thumb points up with other fingers closed. SWING. With arm extended horizontally, index finger points in direction that boom is to swing. RETRACT TELESCOPING BOOM. With hands to the front at waist level, thumbs point at each other with other fingers closed. RAISE THE BOOM AND LOWER THE LOAD. With arm extended horizontally to the side and thumb pointing up, fingers open and close while load movement is desired. DOG EVERYTHING. Hands held together at waist level. LOWER. With arm and index finger pointing down, hand and finger make small circles. LOWER BOOM. With arm extended horizontally to the side, thumb points down with other fingers closed. EXTENDED TELESCOPING BOOM. With hands to the front at waist level, thumbs point outward with other fingers closed. TRAVEL/TOWER TRAVEL. With all fingers pointing up, arm is extended horizontally out and back to make a pushing motion in the direction of travel. LOWER THE BOOM AND RAISE THE LOAD. With arm extended horizontally to the side and thumb pointing down, fingers open and close while load movement is desired. MOVE SLOWLY. A hand is placed in front of the hand that is giving the action signal. Part No. 237108 GTH-844 61 Operator's Manual Third Edition • Sixth Printing Attachments Suspended Load Hazards Rigger Requirements (from OSHA CFR 1926.404) When employees are engaged in hooking, unhooking, or guiding the load, or in the initial connection of a load to a component or structure and are within the fall zone, all of the following criteria must be met: The materials being hoisted must be rigged to prevent unintentional displacement. Only approved lifting accessories should be used. Hooks with self-closing latches or their equivalent must be used. Exception: "J" hooks are permitted to be used for setting wooden trusses. The materials must be rigged by a qualified rigger. 62 GTH-844 Part No. 237108 Third Edition • Sixth Printing Operator's Manual Specifications Specifications GTH-844 Tire size 13 x 24, 12 ply Height, stowed 7 ft 10 in 2.39 m Length, stowed, without forks 20 ft 3 in 6.17 m Turning radius (outside), 2 wheel steer 21 ft 9 in Width, standard tires 7 ft 11 in 2.41 m Turning radius (outside), 4 wheel steer 13 ft 9 in 11 ft 4 in 3.45 m Frame leveling (each side) 1 ft 3 in 38 cm Fuel tank capacity 1 ft 5 in 43 cm Maximum grade Weight 22,600 lbs 10251 kg Working fork height, maximum 43 ft 10 in 13.36 m Wheelbase Ground clearance, center Ground clearance, axle 6.63 m 4.19 m 10 degrees 35 gal 132.5 liter 50% Horn sound level, manufacturer's rating 113 dB 107 dB Horizontal reach, maximum 28 ft 2 in 8.59 m Backup alarm sound level, manufacturer's rating Reach at maximum height 2 ft 1 in 64 cm Floor loading information Lift capacity, maximum height with 24 in / 61 cm load center 6000 lbs 2722 kg Lift capacity, maximum reach with 24 in / 61 cm load center 2000 lbs 907 kg Maximum lift capacity 8000 lbs 3629 kg Tire load maximum Occupied floor pressure 15,100 lbs 6849 kg 184 psf 8.8 kPa Drive speed, maximum, Deutz engines 3-speed transmission 15 mph 24.1 km/h 2-speed transmission 6 mph 10.5 km/h Drive speed, maximum, Perkins 854 engines 3-speed transmission 16 mph 25.7 km/h 2-speed transmission 6 mph 10.5 km/h Drive speed, maximum, Perkins 1104 engines 3-speed transmission 14 mph 22.5 km/h 2-speed transmission 5.5 mph 9.7 km/h Part No. 237108 GTH-844 63 Operator's Manual Third Edition • Sixth Printing Load Charts Load Charts GTH-844 Standard Carriage GTH-844 Quick Attach Lifting Point 35 ft 45 ft 10.7 m 13.7 m 30 ft 9.1 m 0 ft 0m 10 ft 3.0 m 20 ft 6.1 m 70° 60° 40 ft 12.2 m D 50° < 2 mph / 3.2 km/h B 40° <15 ft <4.5 m 30 ft 9.1 m C A 30° 20 ft 6.1 m 8000 lbs / 3629 kg 4000 lbs / 1814 kg 6000 lbs / 2722 kg 0° 0 ft 0m 3000 lbs / 1361 kg 10° 10 ft 3.0 m 1600 lbs / 726 kg 20° -8° -5 ft 1.5 m 35 ft 30 ft 10.7 m 9.1 m GTH-844 Rotate Carriage 0 ft 0m GTH-844 Swing Carriage GTH-844 64 10 ft 3.0 m 20 ft 6.1 m GTH-844 Part No. 237108 Operator's Manual Third Edition • Sixth Printing Part No. 237108 California Proposition 65 Warning www.genielift.com Distributed By: The exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Kristin.Johnson Create Date : 2015:01:21 11:33:28-08:00 Modify Date : 2015:05:27 08:43:25-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2015:05:27 08:43:25-07:00 Producer : Acrobat Distiller 10.1.12 (Windows) Format : application/pdf Title : Microsoft Word - 237108_36 GTH-844.docm Creator : Kristin.Johnson Document ID : uuid:d277f660-1a5e-41d1-ac6a-1fed77081617 Instance ID : uuid:6aed274f-4137-4876-82f4-16e8a9c549e0 Page Count : 67EXIF Metadata provided by EXIF.tools