HP OmniBook 300, 425, 430, And 530 PC Service Manual, 5965 0244 300

User Manual: 300

Open the PDF directly: View PDF PDF.
Page Count: 86

DownloadHP OmniBook 300, 425, 430, And 530 PC Service Manual, 5965-0244 300
Open PDF In BrowserView PDF
Service Manual

HP OmniBook 300, 425, 430, 530

For other Service and User Manuals, go to www.ManualDepot.com

Notice
In a continuing effort to improve the quality of our products,
technical and environmental information in this document is
subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to
this material, including, but not limited to, the implied warranties
of merchantability and fitness for a particular purpose. HewlettPackard shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished by
Hewlett-Packard.
As an ENERGY STAR partner, HP has determined that these
products meet the ENERGY STAR guidelines for energy
efficiency.
All Certifications may not be completed at product introduction.
Please check with your HP reseller for certification status.
This equipment is subject to FCC rules. It will comply with the
appropriate FCC rules before final delivery to the buyer.
ENERGY STAR is a service mark of the U.S. Environmental
Protection Agency. IBM and OS/2 are registered trademarks of
International Business Machines Corporation. Pentium and the
Intel Inside logo are registered trademarks of Intel Corporation.
LapLink Remote Access is a trademark of Traveling Software,
Inc. Microsoft, MS-DOS, and Windows are registered
trademarks, and the Genuine Microsoft Products logo is a
trademark of Microsoft Corporation in the United States of
America and in other countries.
 Hewlett-Packard Company 1996.
All Rights Reserved. Reproduction, adaptation, or translation
without prior written permission is prohibited except as allowed
under copyright laws.
Printed in U.S.A.
5965-0244

Table of Contents
Table of Figures .........................................................................................................................iv
Introduction .................................................................................................................................v
Product Overview........................................................................................................................1
Product Features .....................................................................................................................2
OmniBook 300, 425, and 430 ...............................................................................................2
OmniBook 530 .....................................................................................................................3
Product Comparisons...............................................................................................................4
Product at a Glance .................................................................................................................6
Troubleshooting...........................................................................................................................9
OmniBook Self-Test...............................................................................................................10
Loop Back Connectors........................................................................................................10
Troubleshooting Flowchart .....................................................................................................12
Main Troubleshooting Flowchart .........................................................................................13
Power Source Problems .....................................................................................................15
Boot-Up Problems ..............................................................................................................18
Display Problems ...............................................................................................................19
Hard Disk Problems............................................................................................................20
Memory Problems ..............................................................................................................23
Power Management Problems............................................................................................25
Pop-Out Mouse Problems...................................................................................................28
Floppy Drive Problems .......................................................................................................32
Parallel Port Problems........................................................................................................35
Serial Port Problems ..........................................................................................................37
PCMCIA Problems .............................................................................................................39
IR Port Problems ................................................................................................................43
Hardware Repair .......................................................................................................................45
Battery (End User Replaceable).............................................................................................46
Memory (End User Replaceable) ...........................................................................................48
Hard Disk Drive/Flash Card and System ROM (End User Replaceable).................................50
Mouse (End User Replaceable)..............................................................................................52
Small Parts (End User Replaceable) ......................................................................................53
Battery Door .......................................................................................................................53
Battery Door Latch..............................................................................................................53
Blank Modem Door.............................................................................................................53
Memory Door .....................................................................................................................53
I/O Door .............................................................................................................................53
Rubber Feet .......................................................................................................................53
PCMCIA Card Tray.............................................................................................................53
Display (HP Authorized Service Providers Only)....................................................................54
Keyboard (HP Authorized Service Providers Only) ................................................................62
Logic PCA Board (HP Authorized Service Providers Only).....................................................63
Paw Carrier (Paw Active) (HP Authorized Service Providers Only) ........................................65
Other Components (HP Authorized Service Providers Only)..................................................66
Appendix A - Technical and Resource Specifications ................................................................67
Mass Storage Specifications ..................................................................................................67
Card Services and Socket Services Version Matrix................................................................67
Memory Map..........................................................................................................................68
Upper Memory Block Space...................................................................................................68
DOS Conventional Memory ...................................................................................................68
Appendix B - Power On Self Test Codes ...................................................................................69
Beep Codes ...........................................................................................................................69
Display Codes........................................................................................................................70
Appendix C - Password Policy...................................................................................................75

ii

Appendix D - Part Numbers.......................................................................................................77

iii

Table of Figures
Figure 1 - OmniBook 300, 425, and 430 Features .......................................................................2
Figure 2 - OmniBook 530 Features..............................................................................................3
Figure 3 - Serial Loop Back Connector ......................................................................................11
Figure 4 - Parallel Loop Back Connector ...................................................................................11
Figure 5 - OmniBook Memory Modules .....................................................................................48
Figure 6 - Removing the Memory Module..................................................................................49
Figure 7 - Removing Card Slot Tray ..........................................................................................51
Figure 8 - Removing the Mouse ................................................................................................52
Figure 9 - Outer Bottom Case Components ...............................................................................54
Figure 10 - Backplane Standoffs................................................................................................55
Figure 11 - Bottom Case Tabs...................................................................................................55
Figure 12 - Bottom Case Prying Locations.................................................................................56
Figure 13 - I/O Port Prying Location ..........................................................................................56
Figure 14 - Disconnecting Display Cable ...................................................................................57
Figure 15 - Keyboard Flex Cables .............................................................................................58
Figure 16 - Display Grounding Eyelets.......................................................................................58
Figure 17 - Display Cable Probe Position ..................................................................................60
Figure 18 - Reconnecting Display Cable....................................................................................60
Figure 19 - I/O Port Eyelets (all present)....................................................................................61
Figure 20 - I/O Port Eyelets (two matched sets).........................................................................61
Figure 21 - I/O Port Eyelets (only one matched set)...................................................................61
Figure 22 - I/O Port Eyelets (no eyelet in position one) ..............................................................61
Figure 23 - Logic Board PCA Removal......................................................................................63
Figure 24 - Paw Carrier Removal ..............................................................................................65

iv

Introduction
This document provides reference information for the HP OmniBook 300, HP OmniBook 425,
HP OmniBook 430, and HP OmniBook 530. It is intended to be used by HP-qualified service
personnel to help with the installation, servicing, and repair of these HP OmniBook PCs.
It is a self-paced guide designed to train you to install, configure, and repair the OmniBook
Notebook PC. You can follow it without having any equipment available.
The following table lists additional sources where supplementary information can be obtained:

v

Resource
HP External Web
HP-MCD Internal Web

Number/Address
http://hpcc998.external.hp.com/mcd/
http://webmcd.cv.hp.com

HP MCD Service
Engineer

svc-eng_mcd@om.cv.hp.com

Comments
No usage restriction
Restricted to HP internet
access only
Email address for service
related questions and
issues

Part 1

Product Overview
• Product Features
• Product Comparisons
• Product at a Glance

Product Features
OmniBook 300, 425, and 430

Figure 1 - OmniBook 300, 425, and 430 Features

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

2

Latch
Display
Keyboard
Card slot A
Card-eject levers
On/Off key
Mouse
Mouse-eject button
Display contrast buttons
Speaker

11.
12.
13.
14.
15.
16.
17.
18.
19.
20.

AC adapter socket
Serial port connector
Parallel port connector
Infrared port
System slots (C and D)
Memory-expansion slot
Modem port
Battery compartment
Security ring
Reset button

OmniBook 530

Figure 2 - OmniBook 530 Features

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Latch
Display
Keyboard
Card slots
Card-eject levers
On/Off key
Mouse
Mouse-eject button
Display contrast buttons
Speaker
AC adapter socket

12.
13.
14.
15.
16.
17.
18.
19.
20.
21.

Serial port connector
Parallel port connector
VGA output connector
System slots
Memory-expansion slot
Modem port
Battery compartment
Security ring
Infrared port
Reset button

3

Product Comparisons
Size Closed
Weight
Processor
Clock Speed
Display
VGA-out Support
Battery

OmniBook 300

OmniBook 425

OmniBook 430

OmniBook 530

16.3 x 28.2 x 3.6 cm
(6.4 x 11.1 x 1.4 in)
1.31 kg (2.888 lb)
w/flash
1.36 kg (2.998) w/hdd
386SXLV
20 MHz
640 x 480 VGA
9-inch diagonal LCD
16 shades of gray
none

16.3 x 28.2 x 3.6 cm
(6.4 x 11.1 x 1.4 in)
1.31 kg (2.888 lb)
w/flash
1.36 kg (2.998) w/hdd
486SLC/e
25 MHz
640 x 480 VGA
9-inch diagonal LCD
16 shades of gray
none

16.3 x 28.2 x 3.6 cm
(6.4 x 11.1 x 1.4 in)
1.36 kg (2.998 lb)

16.3 x 28.2 x 3.6 cm
(6.4 x 11.1 x 1.4 in)
1.36 kg (2.998 lb)

486SLC/e
25 MHz
640 x 480 VGA
9-inch diagonal LCD

Intel 486SX
33 MHz
640 x 480 VGA
9-inch diagonal LCD

none

4.8 Vdc nickel-metalhydride rechargeable
1.5 V alkaline AA (flash
version only)
5 hours w/hdd
9 hours w/flash
100 to 240 Vac (50 to
60 Hz) input
12 Vdc output
less than 1.5 hours
w/ac adapter
0 to 40 C (32 to 104 F)

4.8 Vdc nickel-metalhydride rechargeable
1.5 V alkaline AA (flash
version only)
4.5 hours w/hdd
8 hours w/flash
100 to 240 Vac (50 to
60 Hz) input
12 Vdc output
less than 1.5 hours
w/ac adapter
0 to 40 C (32 to 104 F)

4.8 Vdc nickel-metalhydride rechargeable
1.5 V lithium AA

640 x 480, 16 or 256
colors
800 x 600, 16 colors
4.8 Vdc nickel-metalhydride rechargeable

0 to 55 C (32 to 131 F)

©

4.5 hours

4 hours

100 to 240 Vac (50 to
60 Hz) input
12 Vdc output
less than 1.5 hours
w/ac adapter
0 to 40 C (32 to 104 F)

100 to 240 Vac (50 to
60 Hz) input
12 Vdc output
less than 1.5 hours
w/ac adapter
0 to 40 C (32 to 104 F)

0 to 55 C (32 to 131 F)

0 to 55 C (32 to 131 F)

0 to 55 C (32 to 131 F)

90% relative humidity at
40 C (104 F) maximum

90% relative humidity at
40 C (104 F) maximum

90% relative humidity at
40 C (104 F) maximum

90% relative humidity at
40 C (104 F) maximum

40-MB hard disk
10-MB flash disk
2 MB RAM

40-MB hard disk
10-MB flash disk
2 MB RAM

130-MB hard disk

Memory
Expansion
Available
Input/Output

2-MB, 4-MB

2-MB, 4-MB

105-MB hard disk
40-MB hard disk
2 MB RAM on 40MB version
4 MB RAM on 105MB version
2-MB, 4-MB

9-pin, 115K baud,
RS-232 port
25-pin parallel port
115K baud,
bidirectional infrared
port
Communication port
for optional
fax/modem

9-pin, 115K baud,
RS-232 port
25-pin parallel port
115K baud,
bidirectional infrared
port
Communication port
for optional
fax/modem

9-pin, 115K baud,
RS-232 port
25-pin parallel port
115K baud,
bidirectional infrared
port
Communication port
for optional
fax/modem

9-pin, 115K baud,
RS-232 port
25-pin parallel port
115K baud,
bidirectional infrared
port
Communication port
for optional
fax/modem

Keyboard and
Mouse

85 keys
Industry-standard, fullsized key spacing
Embedded numeric
keypad
9 Fn keys
Built-in pop-up mouse
PCMCIA, Type II,
Version 2.0 card slots
Two slots available with

85 keys
Industry-standard, fullsized key spacing
Embedded numeric
keypad
12 Fn keys
Built-in pop-up mouse
PCMCIA, Type II,
Version 2.0 card slots
Two slots available with

85 keys
Industry-standard, fullsized key spacing
Embedded numeric
keypad
12 Fn keys
Built-in pop-up mouse
PCMCIA, Type II,
Version 2.0 card slots
One slot available with

85 keys
Industry-standard, fullsized key spacing
Embedded numeric
keypad
12 Fn keys
Built-in pop-up mouse
Two PCMCIA Type II
slots (one Type III slot)
Optional floppy disk

Battery Life
AC Adapter
Recharge Time
Operating
Temperature
Storage
Temperature (with
data retention)
Operating and
Storage Humidity
Mass Storage
Available
Memory

Expandability

4

4 MB RAM

4-MB, 8-MB

Pre-installed
Software

OmniBook 300

OmniBook 425

OmniBook 430

OmniBook 530

the flash disk version
One slot available with
the hard disk version
©
MS Windows 3.1*
©
MS DOS 5.0*
MS Word 2.0*
MS Excel 4.0*
LapLink Remote
™
Access
Phone Book
Appointment Book
HP Financial Calculator

the flash disk version
One slot available with
the hard disk version
©
MS Windows 3.1*
©
MS DOS 5.0*
MS Word 2.0*
MS Excel 4.0*
LapLink Remote
™
Access
Phone Book
Appointment Book
HP Financial Calculator

the hard disk version

drive

©

MS Windows 3.1
©
MS DOS 6.2
LapLink Remote
™
Access
Phone Book
Appointment Book
HP Financial Calculator

©

MS Windows 3.11
©
MS DOS 6.2
LapLink Remote
™
Access
Phone Book
Appointment Book
HP Financial Calculator

*(Note: All components not included can be installed from a retail copy. License for full Microsoft Word, Microsoft Excel, MSDOS, and Microsoft Windows is included with purchase.)

5

Product at a Glance

14

28

14
29
27

17
32

35

11

13
16

33

16

5
10
6
2

1

9

18
2

1

1
1

2
2

15

13

7
2

2

13
24

2

12
2

2

26
5

2
30

2
23

13

4
3

6

19
20

8

2
31

21

22

34
25

6

10

Description
Part Number
OB300 OB425 OB430 OB530
Standoff
0380-4060
Screw M2x4.6mm (T6)
0515-2396
Mouse
5061-4390
Arm Eject Mouse Spring
F1030-00016
Pivot Door Spring
F1030-00026
Spring Card Eject
F1030-00029
Mouse Latch Spring
F1030-00030
Mylar Mouse Shield
F1030-20001
Door Battery
Door Battery (10 pack)
F1030-60912
Door Battery (silver)
F1052-40012
10 Pivot Door
Pivot Door (PCMCIA) A
F1030-40013
Pivot Door (PCMCIA) B
F1030-40014
Pivot Door (PCMCIA) Left
F1052-40007
11 Door Modem Blank
F1030-40016
12 Door RAM
F1030-40017
13 Rubber Foot
F1030-40018
14 Hinge Cap
F1030-40019
15 Mouse Button Latch
F1030-40021
16 Battery Door Latch
F1030-40025
17 Security Latch
F1030-40033
18 Eject Button A
F1030-40044
19 Eject Button B
F1030-40045
20 Eject Arm Left
F1030-40046
21 Eject Arm Right
F1030-40047
22 Paw Carrier Srvc Assy
F1030-60901
23 Arm Eject Mouse
F1030-40050
24 Door I/O
F1030-60908
25 Pivot Bracket
F1030-60909
26 Bottom Case
Bottom Case
F1030-60910
Bottom Case (silver)
F1052-60908
27 Top Case
Top Case
F1030-60911
Top Case (silver)
F1052-60907
28 LCD Display Assy (new)
F1030-60904
29 Keyboard
Keyboard USA
F1030-80013
Keyboard German
F1030-80031
Keyboard Spanish
F1030-80032
Keyboard French
F1030-80033
Keyboard International English
F1030-80057
30 Logic PCA
Logic PCA (new)
F1030-60907
Logic PCA (new)
F1033-60907
Logic PCA (new)
F1052-60906
Logic PCA (exchange)
F1052-69008
31 System ROM
System ROM (ABA) - US English
F1033-60908
System ROM (ABB) Int. English
F1033-60909
System ROM (ABD) German
F1033-60910
System ROM (ABF) French
F1033-60911
System ROM (ABE Spanish)
F1033-60912
System ROM (ABA) US English
F1037-60903
System ROM (ABB) Int. English
F1037-60904
System ROM (ABD) German
F1037-60905
System ROM (ABE) Spanish
F1037-60906
System ROM (ABF) French
F1037-60907
32 Battery Pack
F1045-60901
33 Hard Drive Tray
F1065-60029
34 Flash Tray
F1030-60923
35 Mass Storage
5 MB Flash Disk Card
F1012-60902
10 MB Flash Disk Card
F1013-60901
20 MB Flash Disk Card
F1014-60901
40 MB Hard Drive (DOS/Win/PIM)
F1035-60901
40 MB Hard Drive (unprogrammed)
F1050-60901
105 MB Hard Drive (DOS/Win/PIM)
F1037-60908
105 MB Hard Drive (Word/Excel)
F1037-60909
105 MB Hard Drive (unprogrammed)
F1039-60901
130 MB Hard Drive (unprogrammed)
F1057-60901
130 MB Hard Drive (programmed)
F1052-60909
Note, this is a partial parts list. For a complete parts list, please refer to Appendix D or the current Product
Support Plan.
1
2
3
4
5
6
7
8
9

7

Part 2

Troubleshooting
• OmniBook Self Test
• Troubleshooting Flowchart

OmniBook Self-Test
The OmniBook Self-Test provides on-board hardware and firmware diagnostics. To operate the
self-test, perform the following steps:
1.
2.
3.
4.
5.

Save all files and close all applications: The OmniBook is reset at the end of the self-test.
Turn the OmniBook OFF.
Press and hold the [Esc] key and press [ON]. You will hear a short three-tone beep.
Self Test will initialize and start.
To run a test:
Highlight the test name and press [ENTER].
Highlight the test name and press [Ctrl][ENTER] to run a longer
and more extensive version of a test--not available for all tests.
The test runs and its results are reported.
6. To run several tests in a continuous loop:
Highlight one or more using [ space bar ] and press [ENTER].
Each test runs and its results are reported.
Press [Backspace] to stop the loop.
7. To exit the self-test, press [Esc].
Interpretation of test results
A result of “OK” on any test indicates that the test did not find problems while the unit was
operating in its current state. A “BAD” result indicates that the test found a problem while the
unit was operating in its current state. A “BAD” result should always be confirmed by running the
test in a loop for several iterations or running the long version of the test. Further inspection of
the unit to rule out configuration or installation conflicts is necessary prior to diagnosing the unit
as needing repair.
Any test that is halted by [Backspace] is shown as “aborted” and no results are displayed.
The OmniBook will not enter sleep mode while the self-test is executing.

Loop Back Connectors
In order to run the RS232 serial port or parallel port self-test, a loop back connector is needed.
The loop back may be placed on either the OmniBook port or at the end of the corresponding
cable. This feature is also helpful in diagnosing a defective serial or parallel cable.
Loop back connectors may be purchased or can easily be constructed. The following illustrations
identify the correct pin-out configurations for the serial and parallel loop back connectors.

10

Figure 3 - Serial Loop Back Connector

Figure 4 - Parallel Loop Back Connector

11

Troubleshooting Flowchart
The following series of flowcharts is intended as a guide for troubleshooting the OmniBook 300,
425, 430, and 530. Each technician should still rely on personal experience and supplemental
knowledge when diagnosing a problem.
These tips should be kept in mind when referencing the troubleshooting flowcharts:
•
•
•

12

Use the Main Troubleshooting Flowchart to isolate the problem to a particular area.
Use the additional individual troubleshooting flowcharts to narrow down the problem to a
specific component or item.
Always use supplemental information resources, including the Product Support Plan, Service
Notes, and the World Wide Web, to aid in diagnosing problem areas.

Main Troubleshooting Flowchart

START
No

See Hard
Disk
flowchart

No

See
Memory
flowchart

See DOS or
Windows?
Get user
information:
Name
Telephone number
Unit serial number
Repair history

Yes

Memory OK? (No
memory errors)

Yes
Eliminate all
obvious physical
problems?

No

Isolate damage.
Refer to repair
process

Yes
No
Hard disk
operates OK?

Yes
No
OB unit's power
light comes on?

Unit has at least 11/2 hours battery
life?

No
Single beep
during boot-up?

See Bootup
flowchart

No

See Power
Management
flowchart

Yes

Pop-out mouse
works correctly?

Yes
See
something in
display?

Yes

See Power
Source
flowchart

Yes

See Hard
Disk
flowchart

No
See Mouse
flowchart

No
See Display
flowchart

Yes

External floppy
drive operates
correctly?

No

See Floppy
Drive
flowchart

Yes
A

13

Main Troubleshooting Flowchart (continued)

A

Parallel port
operates correctly?

No

See Parallel
Port flowchart

Yes

Serial port
operates
correctly?

No

See Serial
Port
flowchart

Yes

External VGA
operates correctly?

No

See Serial
Port
flowchart

Yes

PCMCIA cards
operate correctly?

Infrared port
operates correctly?

Yes

14

No
See PCMCIA
flowchart

No
See IR
flowchart

If you still have
a problem, it's
in software or in
a part of the
unit not covered
by these
flowcharts.

Power Source Problems

Start: No power
lamp, or low battery
life

Yes

Battery in
Omnibook?

No

Turn Omnibook off

Remove and reinsert
battery

Yes

HP ac adapter
and cable?

Connect OB to ac adapter, plug
adapter into wall socket

No

Done

Turn on Omnibook

Yes

Light on
continuously (not
intermittent)?

See power
light?

No

Try different
power socket

B
A

15

Power Source Problems (continued)

A

Yes

B

Light on
continuously (not
intermittent)?

Try different
power socket

No

Recheck cables,
connections:
ac adapter to
Yes

Ambient
temperature within
specification?

Yes

No

No
Yes

Light still
intermittent?

No
Done: Power
source problem
Done

Done: Bring
temperature within
specifications

Done: Suspect bad
ac adapter, cable, or
connector

Ensure power
coming from
wall socket
Ensure battery
installed
correctly

Go to Power
Management
Problems
flowchart

C

16

See power
light?

Power Source Problems (continued)

C

Can you
substitute known
good ac adapter?

Yes

Yes

See steady
power light?

No

No

Yes
Done: Original ac
adapter or cable
bad

Can you
substitute known
good OB?

Yes

Yes

Done: Suspect
original OB base
unit bad

See steady
power light?

No

Ac adapter
warm?

No

No

Done: Suspect bad
ac adapter or cable

17

Boot-Up Problems

Start: Problems during
bootup

Press Ctrl Alt
Del to get a
clean boot

Multiple beeps

Hear
single or multiple
beeps during
boot?

Single beeps

Yes

See
Windows or DOS
prompt in
display?

Done

Yes

Yes

OB
support utility
disk available?

No

No

OB
support utility
disk available?

No

Suspect software
problem: locate OB
support utility disk and
call back

Insert OB
support utility
disk and reboot

Yes
Done

18

See prompt to
enter time and
date?

No

Done: Suspect bad
Omnibook base unit

Display Problems

Start:
Power light on, but no
display

Physical
inspection of
display

Adjust brightness
and contrast
controls

Yes

Done

See anything in
display?

No

Go to Boot-Up
Problems
flowchart

19

Hard Disk Problems

Start: Hard disk fails to boot
up to DOS or Windows; or
other hard disk problems

See
anything in
drive C:?

Yes

Yes

Yes

Noisy?

No

HP hard
disk?
No

No

Insert hard disk in C:

Done
Speech: Need hard disk to
boot correctly

Yes

See "Nonsystem disk"?

No

Done: Hard
disk bad

Done
Suspect corrupt files
on hard disk

Insert hard disk containing
system files

Boot from OB
companion disk in
drive A:

Done

Do
SCANDISK C:

Yes

A

20

Soft checking
OK?

No

B

Hard Disk Problems (continued)

A

B

Do hard checking.
Save logs.
Let SCANDISK repair errors.

Do hard checking.
Save logs.
Let SCANDISK repair errors.

Yes

Boot from OB companion
disk in drive A:

No

Space available on
hard disk within
spec?

Do SCANDISK C:

Done: Hard
disk bad
Boot from drive C:

Yes

Boots without
errors?

Do CHKDSK C:

No

Yes

No
Number of bad
sectors out of
spec?
Suspect software problem

Done: Hard
disk bad

Done

Go to Boot-Up
Problems
flowchart

Boot from OB companion
disk in drive A:

Do
SCANDISK C: /AUTOFIX

C

21

Hard Disk Problems (continued)

C

Remove disk from
drive A:

Boot from drive C:

Yes

DOS and Windows
boot OK?

No

Give customer general data
recovery hints

Done

Yes

Is
customer willing
to reformat hard
disk?

No

Boot from drive A:
Done: Customer must
purchase another
hard disk
Back up hard disk to A:

Reformat hard disk

Reload image

Done

22

Memory Problems

Start: Problem with
plug-in memory

Yes

No

Intermittent
problem?

End current
session.

Run short OB
memory self-test

Yes

Memory
self-test OK?

Exit software
and turn off OB

No

Remove OB
battery,
disconnect ac
adapter

Run long OB
memory self-test

Yes

Memory
self-test
OK?

Run different
software to
eliminate
potential
software

Yes

Remove and
examine
memory module

No

Done: Suspect bad
memory module
Yes

Memory
appears OK
now?

Done: Suspect
memory module
problem

Module
appropriate and
compatible?

No

With memory
module
removed,
replace battery,
attach ac
adapter

No

Done

A

Done: Memory
inappropriate for
this model OB

23

Memory Problems (continued)

A

Power up OB
(memory module
removed)

Yes

Memory
problem
disappears?

No

Run short OB
memory self-test
(without memory
module)

Done: Suspect bad
memory module

Yes

Memory
self-test OK?

No

Run long OB
memory self-test
(without memory
module)

Yes

Done: Suspect
memory module bad

24

Memory
self-test OK?

No

Done: Suspect OB
base unit bad

Power Management Problems

Start: Low
battery life
Yes

Physical
inspection:
HP battery?
Contacts dirty?
Physically OK?

Done: Suspect
software problem
Yes

Yes

Ac adapter
attached to OB
and wall?

No

See OB
power icon?

No

Is
Windows
running?

No

Start Windows
Attach ac adapter

Yes
Yes

Has unit
recharged
sufficiently?

OB
Power icon in
Control Panel?

No
Yes

Power Mgmnt
icon in OB Tools?

Recharge sufficiently

Yes

Yes

Power on
during
recharge?

No

1-1/2
hours per
charge?

No

No
Speech:
Standard or Off
means
processor
always on; uses
more power

No

Ensure power on
Done

Yes

DOS
or Windows
running?

Enable OB
power
management

No

Start DOS or
Windows
A

Done

25

Power Management Problems (continued)

A

Yes

Yes

Ambient
temperature in
spec?

"Bad/no
battery"
message?

Yes

Ensure ac
adapter plugged
into OB and wall

No

Charging circuitry
may be defective

No

Yes

"Bad/no
battery"
message?

Done: Replace
battery or use OB on
ac power only

PCMCIA cards
installed?

No

Yes
Speech: PCMCIA
cards can use
power even when
not on

No

Speech: DOS
games, TSR's,
other software
can reduce
battery life

Remove PCMCIA
cards, recharge
battery

Yes

Get
1-1/2 hours
battery life?

3rd-party
software
installed?

Disable 3rd-party
software and
recharge battery
No

Done
B

26

No

Bring ambient
temperature
within
specification,
recharge battery

Clean boot:
Ctrl Alt Del, press
F4 during boot

Yes

Does
battery indicator
reach full charge?

No

Power Management Problems (continued)

B

Yes

No

Get 1-1/2 hours
battery life?

Use MSD to
determine what
TSR's are
running

Done

Disable TSR's

Yes

Done

Get 1-1/2 hours
battery life?

No

Done: Suspect bad
or old battery

27

Pop-Out Mouse Problems

Start: OB popout
mouse problem

Eliminate
obvious physical
problems

Yes

See
Windows?

No
Start
Windows
running

Yes

Is
mouse OB
popout mouse?

No

Disable other
mouse

Enable OB
popout mouse

Yes

Yes

A

28

See mouse
pointer?

No

Done: Suspect
software problem
(Windows problem)

Does mouse
pointer move?

B

Pop-Out Mouse Problems (continued)

A

Yes

Reaches all 4
corners of
screen?
Yes

Yes

Is mouse jittery,
intermittent?

No

Can you
calibrate
mouse?

No

No

Done: Mouse
should be OK

Suspect bad
mouse

C

29

Pop-Out Mouse Problems (continued)

B

Suspect software
configuration
problem

Yes

Setup shows
correct mouse
driver?

No

Check for
correct OB
mouse driver
Configure Setup
for correct OB
mouse driver
Yes

Mouse driver
OK?

No

Look at mouse in
Windows Control
Panel

Yes

Mouse
moves?

No

Done: Replace with known
good version of correct
OB mouse driver
Yes

See OB punch
button?

Done: Mouse
OK

No

Set Control Panel
for OB punch
button mouse
Suspect bad
mouse
Yes

OB mouse
works OK?

No

Done

Exit Windows,
run Setup from
DOS command
line

30

C

Pop-Out Mouse Problems (continued)

C

Run OB
diagnostic
program

Yes

Yes

OB mouse
operates
correctly?

No

Suspect mouse
works in known
good OB?

Yes

Does mouse
pass all tests?

Boot normally to
Windows

Can you put
suspect mouse in
known good OB?

Yes

Clean boot:
Ctrl Alt Del,
press F5 when
starting

No

Put known good
OB mouse in
suspect base
unit

No

Remove mouse
from OB base
unit, examine
mouse, and
reinsert

Yes

Known good
mouse works?

No

No
Suspect bad
mouse.

Run OB
diagnostic
program

Done: Suspect
software problem
Yes

Does mouse
pass all tests?

No

Replace mouse.
Have customer
call back if
problem not
solved.

Done
Done: Suspect bad
OB base unit

Done

31

Floppy Drive Problems

Start: External
floppy disk drive
problem

External
FDD is HP
device?

Yes

Yes

Cable is
correct one?

No

No

Done

Locate and
attach correct
cable

Eliminate
obvious physical
problems:
Cable OK?
Pins not bent?
Cable connected
and solidly in
connectors?

Yes

Drive works
OK?

Done

Yes

Yes

A

32

Has drive ever
worked?

Inserts, ejects
known good disk
cleanly?

No

No

B

Done: Suspect bad
or damaged drive

No

Floppy Drive Problems (continued)

A
Clean boot:
Ctrl Alt Del, press
F5 during boot

Yes

Drive works
OK?

No

Done
Run short selftest twice

Yes
With original OB
turned on,
connect good
drive and cable

Can
you swap with known
good drive and
cable?

No

Yes

Suspect software
problem (proceed
to B)
Yes

Good drive
works OK?

Original drive
works OK?

Suspect software
problem

No

Done: Suspect
bad drive

No

With known good
OB turned on,
connect original
drive and cable

Yes

Drive passes
self-test OK?

With known good
OB turned on,
connect original
drive and cable

No
Yes

Original drive or
cable bad

Original OB base
unit bad

Original drive
works OK?

No

Suspect software
problem

33

Floppy Drive Problems (continued)

B

Clean boot:
Ctrl Alt Del,
press F5 during
boot
Yes
Run OB disk
self-test:
Put empty,
known good
disk, formatted
for DOS, in
drive. Press
Enter.

No

Boot from drive
A: with OB
companion disk

Yes

Boots OK?

Insert blank,
formatted floppy
disk, do
long-term disk
self-test

Repeat disk
self-test

Yes

Done: If long-term self-test
works but floppy drive still has
problem, suspect runtime
environment software problem

34

Disk self-test
OK?

Long-term
self-test OK?

Change diskette,
run self-test
again

No

Yes

No

Self-test
OK?

Suspect bad
floppy diskette;
replace floppy
with known good
one

Done: Suspect
bad floppy drive

No

Parallel Port Problems

Start: Problem with
parallel port
Use PRN
command to
print a file
Yes

No

Problem with
Laplink Remote?

Yes

Prints file
OK?

No

Other printer
available?

No

Troubleshoot
Laplink Remote
Done: Parallel
port OK
Yes
Physical
inspection:
Cable
connected?
Cable pins OK?

Attach OB and
use PRN
command to
print file on
different printer

Clean boot:
Ctrl Alt Del,
press F5 during
boot

Yes

Exit to DOS

See
Windows?

Yes

No
Done: Suspect bad
printer or cable

Prints file
OK?

No

Run OB self-test
diagnostics:
CDIAG or
OBTEST,
depending on
unit

A

35

Parallel Port Problems (continued)

A

Yes

Self-test
OK?

Reconfirm:
Printer plugged
in?
On?
On line?

Done: Bad OB
base unit

Attach printer to
desktop PC

Clean boot to
DOS on desktop
PC:
Ctrl Alt Del,
press F5 during
boot

Yes

Done: Suspect
original OB bad

36

PRN prints
file OK?

No

No

Done: Suspect bad
printer or cable

Serial Port Problems

Start: Problem with
serial port

Yes

Problem with
Laplink Remote?

No

Troubleshoot
Laplink Remote

Install loopback
connector

Physical
inspection:
Cable
connected?
Bent pins?
Cable appears
OK?

Run OB self-test
procedure

Yes

Self-test
OK?

Connected to
what?
Modem?
Printer?
Other?

No

Done: Serial port
OK
Yes
Done: Suspect bad
serial port in OB
base unit

Loopback
connector
available?

No

A

37

Serial Port Problems (continued)

A

Ensure proper
default serial
port
configuration

Yes

No

Serial port
works OK?

Done
Yes

Can you
eliminate all
potential software
conflicts?

No

Eliminate
software
conflicts

Yes

No

Serial port
works OK?

Done

Yes

Done: Suspect
original device or
cable bad

38

Plug another
device and cable
into serial ports

Serial port
works OK?

No

Done: Suspect bad
OB base unit serial
port

PCMCIA Problems

Start: PCMCIA card
problem

Determine type of
card

Yes

Known issue
with this card?

No

Seek additional
information on
card

Yes

Yes

Has card ever
worked?

Has any software been
loaded or modified
since card worked?

No

No

Remove card
(with power on or
off)

Visually inspect
card:
Connectors bent?
Damaged?
Wet?
Suspect software
configuration
problem
Yes

Inspection
reveals
problems?

No

Reinsert card
Done: Suspect bad
PCMCIA card
B
A

39

PCMCIA Problems (continued)

A

B

Clean boot:
Ctrl Alt Del, press
F5 during boot

Press Ctrl Alt Del

Run OB self-test
Yes

Yes

Self-test
OK?

See Windows
display?

No
Exit to DOS
prompt
Yes

See DOS
prompt?

Suspect bad card

Done: Return card
to HP

HP card?

No

Done: Contact card
vendor

Remove card and
run CARDINFO

Interpret
CARDINFO
results

C

40

No

Exit to DOS
prompt

Done: Software
configuration or setup
problem

Yes

No

PCMCIA Problems (continued)

C

Yes

No

Hardware
problem?

Done: Suspect bad
OB base unit

Yes

Check CONFIG.SYS
and AUTOEXEC.BAT

Software
problem?

No

Insert card in top
slot

Run CARDINFO
Done

Insert same card
in bottom slot
Yes

Hardware
problem in both
slots?

No

Suspect bad card

Yes

Card is HP
device?

Run CARDINFO

No

Interpret results

Done: Contact
card vendor
Done: Replace
card

D

41

PCMCIA Problems (continued)

D

Yes

Hardware
problem in one
slot only?

Done: Suspect bad
OB base unit

No

Yes

Software
problem in both
slots?

Yes

Seek further
information consult with
Technical
Support

42

Done: Suspect software
configuration problem

No

Software
problem in one
slot only?

No

Done

IR Port Problems

Start: Problem with
infrared (IR) port

Yes

Problem with
Laplink Remote?

Clean boot:
Ctrl Alt Del,
press F5 during
boot

No

Troubleshoot
Laplink Remote
Run OB self-test

Physical
inspection:
IR port not
covered?
Painted over?
Obscured?

Run IR self-test
in proper
environment

Yes
Ensure
operating
distance within
specification (1
meter or less)

IR self-test
OK?

Done: Suspect
software problem

No

Move OB to
different desk,
room

Run IR self-test
in proper
environment

Ensure
operating
environment OK:
Not next to
bright or
oscillating light?
Yes

Done: Suspect no
problem or software
problem

IR self-test
OK?

No

Done: Suspect bad
OB base unit

43

Part 3

Hardware Repair
• Battery
• Memory
• Hard Disk Drive/Flash Card and
System ROM
• Mouse
• Small Parts
• Display
• Keyboard
• Logic PCA Board
• Paw Carrier
• Other Components
CAUTION:

Always provide proper grounding when performing any of the
following repairs. An electrostatic discharge may cause irreparable
damage to the OmniBook and its components

Battery
(End User Replaceable)
All of the monochrome OmniBook models use the same HP Nickel-Metal-Hydride (NiMH)
Battery Pack, part number F1045A (service replacement part number F1045-60901). However,
for some models, 1.5 V AA batteries can be used in place of the NiMH battery pack. The
following table lists all of the monochrome OmniBooks and the batteries that can be used safely
in each model.

Flash Disk
Version

Hard Disk
Version

WARNING:

OmniBook 300
• NiMH Battery
Pack
• AA Alkaline
• AA Lithium
• NiMH Battery
Pack
• AA Lithium

OmniBook 425
• NiMH Battery
Pack
• AA Alkaline
• AA Lithium
• NiMH Battery
Pack
• AA Lithium

OmniBook 430
not applicable

OmniBook 530
not applicable

• NiMH Battery
Pack
• AA Lithium

• NiMH Battery
Pack

Do not mutilate, puncture, or dispose of batteries in fire. The batteries can
burst or explode, releasing hazardous chemicals.
A nickel-metal-hydride rechargeable battery pack must be recycled or
disposed of properly. Recycle or discard used size-AA batteries according
to the manufacturer’s instructions.

Required Equipment
• none
Removal Procedure
1. Release the two latches on the battery cover on the bottom case, then remove the cover.
Refer to the below illustration.
2. Do one of the following to remove the battery:
• If an OmniBook battery pack is installed, lift it out by its tab.
• If AA batteries are installed in place of the OmniBook battery pack, lift each out
individually.

46

Replacement Procedure
1. To replace the battery, do one of the following:
• To replace the OmniBook battery pack, insert the rounded side of the pack into the
compartment first. It is not possible to fully insert the battery pack incorrectly.
• To replace AA batteries, orient them as shown by the symbols in the battery
compartment.
2. Replace and latch the battery cover.

47

Memory
(End User Replaceable)
The OmniBook 530 uses a unique memory module that is not compatible with the OmniBook
300, 425, or 430. The table below summarizes the compatibility of the memory modules for
each OmniBook model.
Memory
Module
2-MB
4-MB
4-MB
8-MB

Accessory
Number
F1041A
F1042A
F1054A
F1055B

Service Replacement

OB 300

OB 425

OB 430

OB 530

F1041-60901
F1038-60901
F1054-60901
F1055-60002

The following illustration provides a visual representation of the physical differences between the
memory module for the OmniBook 300, 425, and 430 and the memory module for the OmniBook
530.

OmniBook 300, 425, and 430

OmniBook 530

Figure 5 - OmniBook Memory Modules

48

Required Equipment
• Probe (or similar device) for the OmniBook 300, 425, and 430 only

CAUTION:

To avoid damage due to electrostatic discharge, handle the memory module
by the edges only.

Removal Procedure
1. Remove the battery and ac adapter from the OmniBook.
2. Slide the memory door off (see below illustration).

Figure 6 - Removing the Memory Module

3. Perform the appropriate action for the corresponding OmniBook:
• OmniBook 300, 425, or 430 -- Use a probe or similar device to pull on the small post
located on the front edge of the memory module.
• OmniBook 530 -- Flip out the plastic tab on the memory module and pull the module
out.

Replacement Procedure
1. Insert the memory module into the slot. (It is not possible to completely insert the memory if
it is upside down.)
• OmniBook 300, 425, 430 -- the small post on the board faces the bottom surface of the
OmniBook.
• OmniBook 530 – the plastic tab on the board faces the bottom surface of the
OmniBook.
2. Press in the module until it seats fully.
3. Replace the slot cover.
4. Replace the battery and press reset.

49

Hard Disk Drive/Flash Card and System ROM
(End User Replaceable)
The Hard Disk Drives for the OmniBook 300, 425, 430, and 530 can be reimaged if necessary.
If the software is corrupted, or otherwise damaged, on the hard drive, it can be reformatted and
the software reloaded. Also, if the hard drive fails and must be replaced, a blank hard drive can
be ordered and the appropriate software loaded. The below procedures indicate the proper
actions necessary for reloading software on each OmniBook model.
For the OmniBook 300 and 425:
1. Place the hard drive into the OmniBook.
2. Reformat the hard drive.
3. Run OBSETUP /F from the System ROM to reload the software onto the hard drive.
For the OmniBook 430:
1. Place the hard drive into the OmniBook.
2. Reboot and press Alt then D to boot from the System ROM.
3. Reformat the hard drive.
4. Reload the software image from a set of OmniBook 430 Recovery Disks. The Recovery
Disks are available on the HP Internal WW Web at
http://webmcd.cv.hp.com/prodsupp/archive/.
For the OmniBook 530:
1. Place the hard drive into the OmniBook.
2. Boot from the Companion Disk or other bootable floppy disk.
3. Reformat the hard drive.
4. Reload the software image from a set of OmniBook 530 Recovery Disks. The Recovery
Disks are available on the HP Internal WW Web at
http://webmcd.cv.hp.com/prodsupp/archive/.

50

Required Equipment
• none
Removal Procedure
1. Exit all applications, including Windows.
2. Turn the OmniBook off and remove the battery and ac adapter.
3. Turn the OmniBook over, release the two latches on the bottom of the tray, and pull out the
tray. See below illustration.

Figure 7 - Removing Card Slot Tray
4. Lift the Hard Disk, Flash Card, or System ROM out of the tray.
Replacement Procedure
1. Reverse the above steps to replace the Hard Disk, Flash Card, or System ROM.
2. Replace the battery and ac adapter.
3. Press reset.

51

Mouse
(End User Replaceable)
Required Equipment
• none
Removal Procedure
1. Press the mouse-eject button to eject the mouse.
2. Pull the mouse firmly away from the OmniBook (see below illustration). The entire mouse
assembly will pull free.

Figure 8 - Removing the Mouse

Replacement Procedure
1. Place the end of the mouse “stick” into the mouse housing.
2. Slide the mouse into the slot and firmly push the mouse until it is completely flush with the
side of the OmniBook.

52

Small Parts
(End User Replaceable)
The following small parts are all end user replaceable.

Battery Door
Push the two battery door latches away from the battery door. Remove the battery door by lifting
up at the notch in the bottom case. Place the battery door, tab side first, over the battery
compartment. Slide the two battery latches in place to secure the door.

Battery Door Latch
Once the battery door is removed (see above), the battery door latches will slide out of the
bottom case. To replace, align the sides of the latches with the groves in the slots. Press firmly
into place.

Blank Modem Door
Use a flat-blade screwdriver or similar device to press the small latch on the bottom of the blank
modem door. Pull the door free of the bottom case. To replace, simply reinsert the door into the
modem slot and press firmly.

Memory Door
Use a flat-blade screwdriver or similar device to pry the memory door from the bottom case.
Replace by aligning the edges of the door with the slots on the bottom case. Press firmly into
place.

I/O Door
To remove the I/O door, open it fully. Flex the middle of the door until the side pins clear the
holes in the back case. Reverse to replace.

Rubber Feet
Place a probe or similar device between the rubber foot and the plastic of the bottom case. Pry
upward to pop the foot out. To replace, firmly press the foot into the hole.

PCMCIA Card Tray
Slide the two tray latches toward each other. Pull the tray out of the card slot. If present,
remove the PCMCIA card from the tray. To replace the tray, insert into the appropriate card slot.
Slide the two latches away from each other to secure the tray.

53

Display
(HP Authorized Service Providers Only)
Required Equipment
• Appropriate ESD station
• Torx #6 screwdriver
• 5mm Hexdriver
• Two small flat tip screwdrivers (or similar prying devices)
• Probe
Removal Procedure
1. Remove the battery, ac adapter, mass storage, system card (if applicable), memory module
(if installed), modem (if installed), mouse, and any installed PCMCIA accessory cards.
2. Remove the four Rubber Feet and seven Screws from the bottom case (see below
illustration).

Door - Battery
Screw
M2x4.6mm(T6)
(Qty 6)
Battery

Rubber Foot
(Qty 4)

Figure 9 - Outer Bottom Case Components

54

3. Remove the I/O Door and the four standoffs located on the I/O backplane (see figure below).

Figure 10 - Backplane Standoffs

4. Two flat tip screwdrivers, or similar prying devices, are needed to remove the Top Case and
Display Assemblies. Four plastic tabs hold the Top Case and Bottom Case together. Two
tabs are located in each PCMCIA slot (see below illustration). Note, the screws seen in the
PCMCIA slot do not need to be removed.

Figure 11 - Bottom Case Tabs

55

Place a prying device at a tab location between the metal and plastic of the Bottom Case
(see figure below, left). Place another prying device in the PCMCIA eject button (see figure
below, right). To release the tab, simultaneously twist prying device A while lifting on prying
device B. Use caution with this maneuver, as the plastic tabs can break off the Bottom
Case. If this occurs, the Bottom Case must be replaced.

Prying device “A”

Prying device “B”

Figure 12 - Bottom Case Prying Locations

5. Perform step four for each of the four tabs.
6. Once the Bottom Case tabs are released, the Bottom Case and Top Case are being held
together only by the display cable and the two keyboard cables. Do not allow the Top
Case and Bottom Case to separate at this point. The display cable and keyboard
cables will be damaged if they are not properly disconnected.
7. Use a prying device to increase the separation of the Top Case and Bottom Case (see figure
below). Do not separate the Top Case and Bottom Case more than 1 cm. A separation
greater than 1 cm will damage the keyboard flex cables by pulling them out of the
zero-force insertion connectors. The intent is to be able to view the display cable, located
to the left of the ac adapter socket.

Display Cable

Figure 13 - I/O Port Prying Location

56

8. With the separation increased slightly, the display cable can be disconnected using a probe.
Use caution to keep the OmniBook on a level surface. With the Top Case partially
separated, small internal parts may dislodge when the OmniBook is tilted at a sharp
angle. Place the probe at the base of the display cable connector between the two rows of
pins. Use a rocking motion to lift the cable from the connector. See the below illustration for
proper placement of the probe.

Figure 14 - Disconnecting Display
Cable
9. With the display cable removed, the Top Case and Bottom Case can be opened partially to
gain access to the keyboard flex cables (see below illustration). Do not open the unit
completely as this will damage the keyboard flex cables by pulling them out of the
zero-force insertion connectors. Open the zero-force insertion connectors and remove
the keyboard flex cables. The Top Case can now be removed completely from the Bottom
Case.

57

Figure 15 - Keyboard Flex Cables
10. To separate the Keyboard from the Display, five grounding eyelets must be removed from
the display posts (see below illustration). Use caution when removing the grounding
eyelets, as they can be broken off easily. If this happens, the assembly must be
replaced. To prevent the eyelets from breaking, bend the grounding eyelet tabs at the
farthest point from the eyelet.

Proper Tab Bend

Figure 16 - Display Grounding Eyelets
58

11. To remove the Display from the Top Case, the display cable and two grounding cables must
be guided through the holes in the Top Case.
Replacement Procedure
1. Guide the display posts, display cable and two grounding cables on the Display through the
holes in the Top Case.
2. Replace the grounding eyelets over the display posts (see Figure 16). Use caution when
replacing the grounding eyelets, as they can be broken off easily. If this happens, the
assembly must be replaced.
3. Press the Display and Top Case firmly at each display post to snap the assembly in place.
4. Position the Top Case and Display Assembly over the Bottom Case and insert the two
keyboard flex cables into the zero-force insertion connectors. Ensure the connectors are
fully closed. Once the keyboard flex cables are secured in the connectors, do not
allow them to be pulled out. This will damage the cables.

59

5. To reconnect the display cable, position a probe in the cable as shown in the below
illustration.

Figure 17 - Display Cable Probe Position

6. Use the probe to connect the display cable into the connector as shown below. Use caution
to keep the OmniBook on a level surface. With the Top Case partially separated,
small internal parts may dislodge when the OmniBook is tilted at a sharp angle.

Figure 18 - Reconnecting Display Cable

7. With the display cable reconnected, the I/O grounding eyelets must be slid into place. Use
caution when positioning the I/O grounding eyelets as they can be broken off easily.
It is acceptable to reassemble the OmniBook with certain I/O grounding eyelets broken if
there is at least one eyelet in each of the four positions AND at least two matched sets
remaining. See Figure 19, Figure 20, Figure 21, and Figure 22 for examples.

60

Acceptable to reassemble
All eyelets are present.

Figure 19 - I/O Port Eyelets (all present)

Acceptable to reassemble
There are two matched sets
and at least one eyelet in
each position.
Figure 20 - I/O Port Eyelets (two matched sets)

Not acceptable to
reassemble
There is only one matched set.

Figure 21 - I/O Port Eyelets (only one matched set)

Not acceptable to
reassemble
There are two matched set, but
no eyelet in position one.
Figure 22 - I/O Port Eyelets (no eyelet in position one)

8. Open the display and firmly press the Top Case and Bottom Case together around the entire
parameter of the OmniBook. This will lock the tabs of the two cases.
9. Replace the seven screws and four standoffs and the remainder of the components.

61

Keyboard
(HP Authorized Service Providers Only)
Required Equipment
• Appropriate ESD station
• Torx #6 screwdriver
• Two small flat tip screwdrivers (or similar prying devices)
• Probe
Removal Procedure
1. Follow the Display Removal Procedure to separate the Display and Top Case from the
Bottom Case.
2. Once the Display is removed, the Keyboard must now be separated from the Top Case.
Hold the Top Case and Keyboard Assembly exactly as shown in the below illustration.
Top Case and
Keyboard
Assembly
(upside down)

Keyboard
(upside down)

Backside of the
Top Case icon
panel.

Figure - Keyboard Removal Hand Placement
3. Apply even upward pressure with the fingers of the left hand. At the same time use the tip of
the thumb of the right hand to twist the backside of the Top Case icon panel inward and
toward the keyboard. There will be a slight bending in the plastic of the Top Case. This is
normal and will not damage the assembly.
Replacement Procedure
1. To replace the Keyboard, snap it into the Top Case. Ensure the entire perimeter of the
Keyboard is securely snapped into place.
2. Follow the Display Replacement Procedure to replace the Display and remaining
components.

62

Logic PCA Board
(HP Authorized Service Providers Only)
Required Equipment
• Appropriate ESD station
• Torx #6 screwdriver
• Two small flat tip screwdrivers (or similar prying devices)
• Probe
Removal Procedure
1. Follow the Display Removal Procedure to separate the Display and Top Case Assembly from
the Bottom Case.
2. Remove the Eject Arms (both right and left) and Mouse Button Latch and Spring (see below
illustration). Note, the Mouse Latch Spring is very small and can be misplaced easily.
Screw
M2x4.6mm(T6)
(Qty 5)

Eject Arm
Right
Mouse
Button
Latch

Eject Arm Left
Mouse
Latch
Spring

Logic PCA

Paw Carrier
Flex Cable Slot
Eject Arm
Spring
Eject Button A

Eject Button B
Eject Arm
Spring
Figure 23 - Logic Board PCA Removal

63

3. The Eject Buttons and Springs do not need to be removed to gain access to the Logic Board.
However, because they can be dislodged easily, setting them aside is recommended.
4. Remove the Paw Carrier Flex Cable from the zero-force insertion slot.
5. Remove the five (5) screws from the Logic Board (see previous illustration).
6. The Logic Board can now be lifted from the Bottom Case.
Replacement Procedure
1. To replace the Logic Board, reverse the steps in the Removal Procedure. Ensure the Paw
Carrier flex cable is positioned properly – the end of the cable should be folded along the
holes in the cable. This folded portion then needs to be placed between the posts and
guided on the bottom case.
2. Follow the Display Replacement Procedure to replace the Display and remaining
components.

64

Paw Carrier (Paw Active)
(HP Authorized Service Providers Only)
Required Equipment
• Appropriate ESD station
• Torx #6 screwdriver
• Two small flat tip screwdrivers (or similar prying devices)
• Probe
Removal Procedure
1. Follow the Logic Board PCA Removal Procedure.
2. Remove the Mylar Mouse Shield. Refer to the below illustration for location of components.
3. The Mouse Eject Arm and Eject Arm Spring may be removed at this point for convenience.
4. Gently bend the Pivot Bracket Tabs upward. Take caution not to break these tabs. If this
occurs the Bottom Case must be replaced.
5. Remove the Pivot Bracket.
6. Lift the Paw Carrier from the plastic posts holding it in place.
Mylar Mouse
Shield
Pivot Bracket

Paw Carrier
Pivot Bracket
Tabs (Qty 2)
Mouse Eject
Arm

Bottom Case

Eject Arm
Spring

Figure 24 - Paw Carrier Removal

Replacement Procedure
1. To replace the Paw Carrier, reverse the steps in the Removal Procedure.
2. Follow the Logic Board PCA Replacement Procedure to replace the Logic Board and
remaining components.

65

Other Components
(HP Authorized Service Providers Only)
The below table list additional replaceable components and the disassembly procedure(s)
necessary to gain access to each.
Component
Top Case

Disassembly
Procedure(s)
Display
Keyboard

Bottom Case

Display
Logic PCA Board
Paw Carrier

Mouse Button Latch
Mouse Latch Spring

Display

Mylar Mouse Shield
Pivot Bracket

Display
Logic PCA Board

Eject Buttons (A&B)
Eject Arms (L&R)
Eject Arm Spring

Display

Pivot Doors (A&B)
Pivot Door Spring

Display

Hinge Cap

Display

Security Latch

Display

66

Equipment
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe
Torx #6 screwdriver
5mm hexdriver
Two flat tip screwdrivers
Probe

Special Notes

The Hinge Caps
simply slide off of the
ends of the Display.
Use a probe to
remove the Security
Latch from the
Bottom Case.

Appendix A - Technical and Resource
Specifications
Mass Storage Specifications

Average seek
Track to Track
seek
Average Latency
Rotational speed
Data transfer
rate
Buffer to disc
Buffer to host
Buffer size
Spindle start
time

40MB

105MB

131MB

< 19 ms
5 ms

19 ms
6 ms

19ms
6 ms

Flash Disk
Cards (Typical)
2-3 ms
NA

6.67 ms
4503 rev/m

6.72 ms
4464 rev/m

6.72 ms
4464 rev/m

NA
NA

13-21 Mbits /sec
4.5 Mbytes /sec

11.4 - 19.2 Mbits/sec
4 Mbytes /sec

11.4 - 19.2 Mbits/sec
4 Mbytes/sec

2.5 MBytes/sec
6.0 MBytes/sec

32 Kbytes static
RAM
1 sec typical
3 sec maximum

31 Kbytes

31 Kbytes

NA

<2 sec maximum

<2 sec maximum

NA

Card Services and Socket Services Version Matrix
Card Services
Socket Services

OB300
Card BIOS 1.0
1.01a

OB425
Card BIOS 1.0
1.08

OB430
Card BIOS 1.0
1.14

OB530
2.1
2.1

67

Memory Map
300/425

430

SYSTEM BIOS

F
VGA BIOS
E

D

C

B

A

ROM
DOS

430

SYSTEM BIOS

VGA BIOS
UMB SPACE

PCMCIA

PCMCIA
UMB SPACE
VGA RAM
UMB
SPACE

VGA RAM

Upper Memory Block Space
UMB Space Available

OB300/425
64k

OB430
64k + 32k

OB530
112k contiguous

DOS Conventional Memory
Windows DOS Box
(with LapLink Remote)
Exit Windows (with out
LapLink Remote)

68

OB300
315 KB

OB425
315

OB430
505

OB530
404

435 KB

435

533

437

Appendix B - Power On Self Test Codes
Beep Codes
Beep Codes are used to identify a Power On Self Test (POST) error that
occurs when the screen is not available. Once the screen is operational,
diagnostic messages are reported to the screen. There are beep codes for
both fatal and nonfatal system board errors.
The codes are shown as x-y-z where 2-2-1 represents 2 beeps - pause - 2
beeps - pause - 1 beep.

Fatal Errors

Non-Fatal Errors

1-1-1
1-1-3
1-1-4
1-2-1
1-2-2
1-2-3
1-3-1
1-3-2
1-3-3
1-3-4
1-4-1
1-4-2
2-1-1
2-1-2
2-1-3
2-1-4
2-2-1
2-2-2
2-2-3
2-2-4
2-3-1
2-3-2
2-3-3
2-3-4
2-4-1
2-4-2
2-4-3
2-4-4
3-1-1
3-1-2
3-1-3
3-1-4
3-2-4
3-3-4
3-4-1
3-4-2
3-4-3

4-2-1
4-2-2
4-2-3
4-2-4
4-3-1
4-3-3
4-3-4
4-4-1
4-4-2
4-4-3

CPU failure
CMOS failure
BIOS Checksum failure
8253 timer failure
DMA setup failure
DMA page register failure
RAM refresh not verified
SMI RAM bad
Low 64K RAM failure
Low 64K RAM even/odd failure
Low 64K RAM address line failure
Low 64K RAM parity error
Low 64K RAM bit 0 error
Low 64K RAM bit 1 error
Low 64K RAM bit 2 error
Low 64K RAM bit 3 error
Low 64K RAM bit 4 error
Low 64K RAM bit 5 error
Low 64K RAM bit 6 error
Low 64K RAM bit 7 error
Low 64K RAM bit 8 error
Low 64K RAM bit 9 error
Low 64K RAM bit 10 error
Low 64K RAM bit 11 error
Low 64K RAM bit 12 error
Low 64K RAM bit 13 error
Low 64K RAM bit 14 error
Low 64K RAM bit 15 error
DMA #2 register error
DMA #1 register error
8259 #1 error
8259 #2 error
8042 KB controller error
Video initialization error
Video retrace failure
Video ROM-scan in progress
Video ROM-scan error

8253 timer tick test
Shutdown/Restart sequence
Gate A20 failure
Unexpected virtual mode interrupt
RAM test in progress
8253 timer channel 2 test
Time of day clock test
Serial port test
Parallel port test
Math coprocessor test

69

Display Codes
There are a number of Power On Self Test (POST) tests that are performed after the Beep Code
tests. Failure of one or more of these tests will result in a displayed failure code (such as 0240).
It is extremely important not to interpret a failure code immediately as a hardware failure. The
failure should be confirmed with a clean boot. A clean boot is defined as pressing the reset
button after removing all accessories (including memory cards, external floppy drive, modems,
PCMCIA cards, and printers) and providing a reliable power source.
The following list explains a number of POST Display Codes. Note, not all codes are available
on all models of the OmniBook.
No Error; Self-Test
Routine Passed

0000h

test passed

80x86 Microprocessor
Error

000fh

MPU failed self test

BIOS ROM Checksum
Errors

0010h

errors relating to the BIOS rom
checksums

0011h
Real Time Clock Errors

0110h
0120h

011X where X = bad register
RTC clock tick error

CMOS Errors

0240h
0241h
0280h
0282h

CMOS power bad
CMOS checksum bad
HP checksum bad
EISA checksum bad

error code 0281 was previously used

8041 Errors

0301h
0302h
0303h
0305h
0306h
0307h
0308h
0311h
0312h
0341h
0342h
0342h
00343h
00344h
00345h
00346h
0350h
0351h

70

did not read 0AAH command
did not respond to 0AAH command
bad Response to 0AAH command
did not respond when setting keyclick
volume
did not read 0C0H command
did not respond to 0C0H command
keyboard fuse is open
did not read 060H command
did not read data for 060H command
did not read kbd interface test cmd
did not respond to kbd intrf test
add 1-4 to this to get
kbd clock line stuck low
kbd clock line stuck high
kbd data line stuck low
kbd clock line stuck high
no ACK from kbd test
bad ACK from kbd test

0352h
0353h
0354h

kbd not connected
no response from kbd test
kbd test failed

error codes 0304, 0313-0314, 0321-0323, 0331-033C were
previously used

AUX Self Test Errors

03E0h
03E1h
03E2h
03E3h
03E4h
03E5h
03E6h
03E7h
03E8h
03E9h
03EAh
03EBh
03ECh

Protected-Mode Switch
Error

0401h

send enable-aux cmd to 8042 cmd
byte failed
8042 failed to accept write-auxdevice cmd
write-aux-device cmd not sent by
8042
reset-aux cmd not accepted by 8042
8042 failed to send aux-interface-test
no reply for aux-interface-test cmd
from 8042
aux device clock line stuck low
aux device clock line stuck high
aux device data line stuck low
aux device data line stuck high
no reply for aux-reset cmd from aux
aux failed to perform reset
send default cmd to 8042 cmd byte
failed
failed to switch to protected mode

error code 0500 was previously used

0503h

no serial port

0505h
0543h

bad serial port
no parallel port

Keyboard Device
Errors

0600h

kbd has keys stuck
06XXh where XX = the scan code of
the stuck key

System Speed Test
Errors

0702h

timer failed to interrupt

0703h
0704h
0707h
0708h

CPU clock too slow in SLOW speed
CPU clock too fast in SLOW speed
CPU clock too slow in FAST speed
CPU clock too fast in FAST speed

Serial and Parallel Test
Errors

error codes 0700-0701, 0705-0706, 0709-070C were
previously used

Timer Chip Errors

EISA Init Errors

1100h
1200h
1201h

failed timer test
110Xh where X = failed timer #
no refresh tick
refresh signal stuck low

13XY

X = slot number where error occurred

71

1300h
1301h
1302h
1303h

1304h
1305h

Memory Configuration
(POST) Errors

2000h

bad port or wrong memory board

2001h
2002h
2003h

bad port or wrong board type
port reports null or no SIMMs
can't mix single and double density
SIMM parts
physical SIMM config. invalid 20X5h
X = the memory bank the checking
routine stopped at - banks are
numbered 0, 1, 2, or 3
bad memory controller

2005h

2006H
DMA Errors

Y = error type
error code displayed if fdc is not
configured properly
error code if board is not ready
error code if cmos says slot is empty
but a card is present in the slot
error code if cmos says slot does not
have board with readable id but can
read board id
error code if cmos id and board id do
not match
error code if incomplete configuration
bit is set

21XYh

213Xh

22XYh

0010h

DMA controller errors
XY= 0001 bbbb = register bbbb of
controller 01 failed write/read test
XY= 0010 bbbb = register bbbb of
controller 02 failed write/read test
DMA status register errors
X=0 => Controller 1's status register
failed
X=1 => Controller 2's status register
failed
DMA Page register errors
XY= 0001 abbb = channel bbb of
page register bad
bit a
0 = ISA (0xxh) register
1 = EISA (4xxh) register
DMA page mask

error codes 3000-3010 were previously used

Real-Mode (0-1Mb)
RAM Errors

4000h

4XYZ - the interpretation of this error
code is machine dependent

error codes 5000-5FFF were previously used

RAM Address Line
Independence, Parity,
& IO_CHK Errors

6100h

6200h

72

errors relating to the address
independence test of ram
XX = xxxx bbbb = address line
bbbb is bad (no. 0 to 19)
errors relating to the RAM parity 620X

6300h

BIOS and Memory
Shadow-RAM Errors

8259 Interrupt
Functionality Errors

test (low 640k).
x = 64k bank no. with problem (i.e.
6204 = bank 4 is bad = address
range 40000h to 4ffffh)
I/O channel check came active during
write read test of protected mode ram
63xx = xx = 256k ram bank/block
with problem

6500h

shadow RAM BIOS failed

6510h
6520h
65A0h
65B0h
65C0h
65D0h
65E0h
65F0h

shadow RAM video BIOS failed
shadow RAM option ROM failed
A000 shadow RAM test failed
B000 shadow RAM test failed
C000 shadow RAM test failed
D000 shadow RAM test failed
E000 shadow RAM test failed
F000 shadow RAM test failed

07000h

7XYY where
X = 0 master's mask reg. failed
X = 1 slave's mask reg. failed
YY = XOR of value read & written to
the mask reg
IRQ 0 error
IRQ 8 error

07400h
07500h

error code 7600 was previously used

Hard Disk Errors

8310h
8311h
8312h

controller fail
fixed disk fail
drive splitting failure

error codes 8001-8002, 8100, 8200, 8300 were previously
used

Flexible Disk Errors

9X0Z

9000H
9001H
9002H
9003H
9005H
9006H
9008H
9009h

X = drive number (0..3 correspond to
drives A:, B:, FDE#1, FDE#2)
Z = determined by the following
equates
FDC input error
FDC output error
FDC seek error
FDC recall error
FDC reset error
FDC wrong drive
FDC no interrupt
FDC track 0 error

error codes 90XX and 98XX were previously used

80x87 Numerical CoProcessor Errors

0a001h

there is no 80287 in the system

0a002h
0a003h

problem with the 80287's registers
problem with the 80287's stack

73

Weitek Numerical CoProcessor Errors

Video Errors

0a004h
0a005h
0a006h
0a007h
0a008h
0a009h
0a00ah
0a00bh
0a00ch
0a00dh
0a00eh

FXCH or FCOMP didn't work
FADD didn't work
FMUL didn't work
FDIV didn't work
FSQRT didn't work
FPATAN didn't work
invalid operation exception err
denormal operand exception error
zero divide exception error
overflow exception error
underflow error

0af00h

failed to enter protected mode

0af01h
0af02h
0af05h
0af06h
0af0Ch

there is no Weitek in the system
error in Weitek data register
ADD didn't work
MULT didn't work
Zero Divide exception error

0b009h

beep if no video card is installed

error codes B001-B008, B100, B200, B301-B307, B400BFFF were previously used

Cache Errors

0b308h
0b300h

internal cache error
P4 cache test failure

Protected Mode RAM
Errors

0c000h

0CXYZ - the interpretation of this
error code is machine dependent

error codes D000, D003-D040, D050, D1XX, EXXX, FFXX
were previously used

74

Appendix C - Password Policy
If the user forgets the system password, there is a master password that will
unlock the OmniBook. The user calls Technical Support to determine this
master password as follows:
1. Support will tell the user the keys to type at the password entry screen:
[alt][shft][f10]
2. The OmniBook generates and displays an encoded master password. This
is displayed under the normal password entry area. At this point, this is the
only password that will unlock the OmniBook unless the user presses [ESC] to
remove the encoded master from the password entry screen. Then the user's
stored password can be entered.
3. The user reads the encoded master password to Support.
4. Support runs a program that decodes the encoded password, and reads the
decoded password (alphanumeric) to the user.
5. The user types in the decoded password.
6. OmniBook decodes the encoded master password it generated and
compares it to the decoded password typed in by the user.
7. If the two passwords match, the OmniBook is unlocked. The forgotten
password is automatically erased. Support can then guide the user through
the process of entering a new password.
8. If the two passwords do not match, the previous sequence must be
repeated until the user correctly enters a master password.
The encoded master password is an eight-character alphanumeric sequence
that the OmniBook generates at random every time the appropriate keys are
pressed in the password entry screen. Because it is generated randomly, a
master password can only be used to unlock the OmniBook once. If the user
forgets the password at another time, it will require another call to Support. (If
the user presses the appropriate keys by mistake, pressing [ESC] will allow
entering the stored password.)
The password descramble programs for the HP OmniBook PCs are protected
as HP Company Private information. They may not be copied, backed-up,
printed or distributed. There are only six official copies of each program.
In addition to the program being protected, its use is also controlled. HewlettPackard and authorized support providers must ensure with written evidence
that the OmniBook that is being "descrambled" is actually in the hands of the
unit's actual and current owner. This requires a sales receipt showing the unit
serial number and owner's name, or a written statement from the owner
attesting that he or she is the owner of the unit. The statement can be a FAX
copy of the document. The fact that the unit is in the hands of an HP
representative on behalf of the customer is not evidence of ownership. In
addition, HP will not descramble a unit for any non-owner, even if it involves
law enforcement agencies. If you receive such a request, you should notify
management and HP Corporate Legal immediately. (These requests may
require a court order prior to our participation.)

75

Further, you must log the name, serial number and date of the running of the
descramble program, and file the written backup with the log. The log and
backup are subject to standard record retention process and review.
The final issue relating to descramble of passwords is that HP cannot provide
information to users that would assist them in improperly descrambling a
password and opening a unit.

76

Appendix D - Part Numbers
Part Number
0380-4060
0515-2396
F1030-00016
F1030-00026
F1030-00029
F1030-00030
F1030-20001
F1030-40013
F1030-40014
F1030-40016
F1030-40017
F1030-40018
F1030-40019
F1030-40021
F1030-40025
F1030-40033
F1030-40044
F1030-40045
F1030-40046
F1030-40047
F1030-40050
F1030-60901
F1030-60904
F1030-60907
F1030-60908
F1030-60909
F1030-60910
F1030-60911
F1030-60912
F1030-60923
F1030-60924
F1030-60925
F1030-60926
F1030-80013
F1030-80015
F1030-80018
F1030-80019
F1030-80031
F1030-80032
F1030-80033
F1030-80044
F1030-80057
F1030-80063
F1033-60901
F1033-60902
F1033-60907
F1033-60908
F1033-60909
F1033-60910
F1033-60911

Description
Standoff
Screw M2x4.6mm (T6)
Arm Eject Mouse Spring
Pivot Door Spring
Spring Card Eject
Mouse Latch Spring
Mylar Mouse Shield
Pivot Door A
Pivot Door B
Door Modem Blank
Door RAM
Rubber Foot
Hinge Cap
Mouse Button Latch
Battery Door Latch
Security Latch
Eject Button A
Eject Button B
Eject Arm Left
Eject Arm Right
Arm Eject Mouse
Paw Carrier Srvc Assy
LCD Display Assy (new)
Logic PCA (new)
Door I/O
Pivot Bracket
Bottom Case
Top Case
SVC Door Battery (10 pack)
SVC Flash Tray Assy
SVC ID Plate (10 pack)
SVC Short Bar (10 pack)
SVC Bat Jumper (10 pack)
Keyboard USA
Regulatory Label
Icon Label
Logo - Display
Keyboard German
Keyboard Spanish
Keyboard French
Foam Shipping Pouch
Keyboard Int English
FFC - Theta
Regulatory Label (10 pack)
SVC Icon Label 425 (10 pack)
Logic PCA (new)
Sys ROM (ABA) - US English
Sys ROM (ABB) Int. English
System ROM (ABD) German
System ROM (ABF) French

OB300 OB425 OB430 OB530

77

Part Number
F1033-60912
F1037-60901
F1037-60902
F1037-60903
F1037-60904
F1037-60905
F1037-60906
F1037-60907
F1052-40007
F1052-40012
F1052-60005
F1052-60906
F1052-60907
F1052-60908
F1052-60914
F1052-60915
F1052-69008
F1065-60029

Description
OB300 OB425 OB430 OB530
System ROM (ABE) Spanish
SVC Icon Label 430 (10 pack)
Custom Icon Kit (10 pack)
Sys ROM (ABA) US English
Sys ROM (ABB) Int. English
System ROM (ABD) German
System ROM (ABE) Spanish
System ROM (ABF) French
PCMCIA Door Left
Door Battery (silver)
Flash Tray Assy w/ plug (qty 1)
SVC Logic PCA (new)
Top Case (silver)
Bottom Case (silver)
Icon Label (10 pack)
Regulatory Label (10 pack)
SVC Logic PCA (exchange)
Hard Drive Tray
Accessories
Floppy drive
0950-2630
Mouse
5061-4390
Power Cord Swiss
8120-2104
Power Cord Danish
8120-2956
Power Cord S. Africa
8120-4211
Power Cord Japan
8120-5342
Power Cord US
8120-6260
Power Cord UK
8120-6261
Power Cord Europe
8120-6262
Power Cord Australia
8120-6346
AC Adaptor-worldwide
9100-5315
F1045-60901 Battery Pack
F1041-60901 2MB RAM Exp
F1054-60901 4MB RAM Exp
F1055-60002 8MB RAM Exp
F1038-60901 4MB RAM Exp
F1012-60902 5MB Flash disk card
F1013-60901 10MB Flash disk card
F1014-60901 20MB Flash disk card
F1037-60908 105MB HDD DOS/Win/PIM
F1037-60909 105MB HDD Word/Excel
F1035-60901 40MB HDD w/ DOS,WIN,PIM
F1050-60901 40MB Unprogrammed HDD
F1039-60901 105MB Unprogrammed HDD
F1052-60909 130MB HDD Programmed
F1057-60901 130MB Unprogrammed HDD
F1040-60901 F1040A Fax/Modem ABA US
F1047-60901 Serial cable
F1052-60910 VGA cable
F1059-60901 Floppy drive cable-parallel
F1030-90085 Ops Manual/QuickStart Guide
F1030-90086 Manual-Vol.2-Excel,PIM,Word
Note, for the most current parts list, always refer to the latest Product Support Plan.

78

HP Part Number
5965-0244



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Create Date                     : 1997:03:20 15:22:29Z
Subject                         : 
Modify Date                     : 2003:02:12 17:18:16-05:00
Page Count                      : 86
Page Layout                     : SinglePage
Creation Date                   : 1997:03:20 15:22:29Z
Producer                        : Acrobat PDFWriter 2.11 for Windows
Author                          : 
Keywords                        : 
Mod Date                        : 2003:02:12 17:18:16-05:00
Metadata Date                   : 2003:02:12 17:18:16-05:00
Title                           : HP OmniBook 300, 425, 430, and 530 PC Service Manual, 5965-0244
Creator                         : 
Description                     : 
Page Mode                       : UseThumbs
Has XFA                         : No
EXIF Metadata provided by EXIF.tools

Navigation menu