351513 F061311B OSSP OPER MANUAL !! 1 Os900sps
Preview ! 351513-1_os900sps Billy Goat Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
User Manual: !! Billy Goat Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
Open the PDF directly: View PDF .
Page Count: 21
Download | |
Open PDF In Browser | View PDF |
OS900SP Owner’s Manual Unit shown with Seed Box Lid, sold separately BILLY GOAT SELF PROPELLED OVERSEEDER OS900SPS, OS900SPH Owner's Manual Accessories Replacement Parts Seed Box Lid Kit Chariot Kit Reel Kit A convenient way to enclose the seed box Allows the user to ride behind the unit and decrease fatigue from walking Use to replace worn or damaged reels P/N 351600 P/N 351601 P/N 351603 Part No 351513 1 Form No F061311B OS900SP Owner’s Manual CONTENTS SPECIFICATIONS AND SOUND/VIBRATION ___ 3 INSTRUCTION LABELS 4 PACKING CHECKLIST & ASSEMBLY 5 OPERATION 6-7 MAINTENANCE 8 TROUBLESHOOTING____________________________ PARTS LIST____________ Part No 351513 9 10-21 2 Form No F061311B OS900SP Owner’s Manual Specifications OS900SPS OS900SPH Engine: HP’ 9.0 HP (6.7kW) 9.0 HP (6.7kW) Engine: Model EX270D50021 GX270K1QA2 Engine: Type Subaru Honda Engine: Fuel Capacity 6.4 qt. (6.1 L) 5.6 qt. (5.3 L) Engine: Oil Capacity 1.06 qt. (1 L) 1.16 qt. (1.1 L) Total Unit Weight: 314# (142 kg) 323# (147 kg) Max. operating slope 15 o Sound test in accordance with 2000/14/EC 104 dB(a) Sound at operators ear 84 dB(a) 20o 104 dB(a) 84 dB(a) 2 Vibration at operator position 0.81g (7.95 m/s ) 0.81g (7.95 m/s2) SOUND SOUND LEVEL 84 dB(a) at Operators Position 104 Sound tests were conducted in accordance with 2000/14/EC, and were performed on 10-13-2010 under the conditions listed below. Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound power level for your model. General Conditions: Temperature: Wind Speed: Wind Direction: Humidity: Barometric Pressure: Sunny o o 73 F (23 C) 11 mph (17 kmh) South West 27% 30.34Hg (770 mm Hg) VIBRATION DATA 2 VIBRATION LEVEL .81g (7.95m/s ) Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test equipment. Tests were performed on 10-13-2010 under the conditions listed below. General Conditions: Temperature: Wind Speed: Wind Direction: Humidity: Barometric Pressure: Part No 351513 Sunny o o 66 F (19 C) 3 mph (4.8kph) East 30.2% 29.9Hg (101.3kpa) 3 Form No F061311B OS900SP Owner’s Manual INSTRUCTION LABELS ® The labels shown below were installed on your BILLY GOAT Overseeder. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown. LABEL DANGER KEEP HANDS AND FEET AWAY ITEM #145 P/N 400424 LABEL CAUTION GUARDS ITEM #133 P/N 900327 LABEL CLUTCH ITEM #142 P/N 500177 LABEL TRANS. RELEASE ITEM #146 P/N 351507 LABEL DEPTH GAUGE ITEM #59 P/N 351504 LABEL INSTRUCTIONS SEEDER BOX ITEM #56 P/N 351501 (page 12) LABEL SEED METERING ITEM #66 P/N 351503 (page 12) ENGINE LABELS SUBARU HONDA READ OWNER’S MANUAL BEFORE OPERATION. LIRE LE MANUEL D UTILISATEUR AVANT USAGE. VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN. NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL HONDA MOTOR CO. , LTD. MADE IN JAPAN OIL ALERT WHEN OIL LEVELLOW, ENGINE STOPS IMMEDIATELY. . Part No 351513 4 Form No F061311B OS900SP Owner’s Manual PACKING CHECKLIST Your Billy Goat Overseeder is shipped from the factory in one carton, completely assembled. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the unit and cables could snag. PUT OIL IN ENGINE BEFORE STARTING PARTS BAG & LITERATURE ASSY Warranty card P/N- 400972, Owner’s Manual P/N-351513, General Safety and Warnings Manual P/N100295, Declaration of Conformity P/N-351508. Boxing Parts Checklist Subaru 9 HP Honda 9 OHV Parts bag P/N-351009 ASSEMBLY 1. UNFOLD the upper handle and slide handle lock loops (item 35) into place to secure the upper handle to the lower. 2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move height adjust lever to down position, to level engine during checking. See engine manufacturers’ instruction manual. 3. CONNECT spark plug wire. Part No 351513 5 Form No F061311B OS900SP Owner’s Manual OPERATION FOLDING HANDLE This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by sliding the handle lock loops (item 35) up. This releases the upper handle, allowing it to be folded over the unit. ADJUSTING BLADE DEPTH The depth of the blades can be raised or lowered by rotating the knob located at the rear of the machine. The relative depth of the blades can be gauged by using the depth scale located on the rear of the machine and the bar next to it. BLADE POSITION & DEPTH CONTROL LEVER The blades can be raised or lowered into the ground by height adjustment lever at the rear of the unit. The blades will be in their lowered position when the lever is to the left and should be locked in the notch on the right when in transport. The resulting blade depth can be adjusted higher or lower. See ADJUSTING BLADE DEPTH above. SLICING TIPS Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe. Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to determine the depth of thatch in your yard. THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time at the base of the lawn preventing air, water, and fertilizer from reaching the soil. This can cause shallow root development and make a lawn more susceptible to drought and disease. Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of thatch will keep your lawn in good health. HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in one treatment will damage or destroy the living part of the lawn. It is best to remove heavy thatch in seasonal treatments (i.e. spring, and fall). SLOPES: Rake slopes across not up and down. This is much easier and safer for the operator and is better for the lawn. Raking across will help to reduce runoff during watering and allow the sloped ground to hold more seed, fertilizer, and water. The unit’s maximum operating slope is 35% or 19°. DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear. Setting the reel deeper will not produce better, or quicker results. The slicing reel should be set even with the ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding jobs. Setting the reel deeper than this will only result in premature wear on the unit (i.e. failed belt). If you desire to work the ground deeper than the above guidelines allow, it should be done gradually in multiple passes.. VERTICUTTING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in crisscross pattern (See Fig. 1 and See Fig 2). Part No 351513 6 Fig. 1 Fig. 2 Form No F061311B OS900SP Owner’s Manual VERTI-CUTTING OPERATION MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall) DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass. SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e. driveway, or sidewalk). START ENGINE: See Page 9. ENGAGE BLADES: Push the Reel Lever down on the operators handle (upper left side). NOTE: When engaging the blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the turf. SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be removed and deposited on top of the healthy grass. Grass runners should be cut and ready for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or bounces during operation the blade depth is set too low. REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch/stems. OVERSEEDING OPERATION MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall) DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass. SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5 kg. per 93 m2 ]) Adjustments to the seed drop is located on the front of the unit on the seed dial and should be used in conjunction with the seed chart on the console. SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm) below a flat surface (i.e. driveway, or sidewalk). START ENGINE: See Page 9. ENGAGE REEL AND SEED DROP: Push down on the Reel lever on the operators handle. NOTE: When engaging the reel in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the reel. Slowly lower the unit into the turf. SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or bounces during operation the blade depth is set too low. WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed suppliers directions. ADJUSTING SEED RATE To set the seed flow rate, loosen the knob on the indicator dial and set it to the corresponding stop setting on the seed application chart (below or on the console) for the type and amount of seed being used. INSTRUCTION LABEL P/N 351501 Part No 351513 7 Form No F061311B OS900SP Owner’s Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use (daily) Every 25 Hours z Inspect for loose, worn or damaged parts. z Check engine oil z Inspect belts Engine (See Engine Manual) z Grease bearings z Inspect and clean engine air filter z Oil height adjustment linkage SLICING BLADE WEAR 1. Wait for engine to cool and disconnect spark plug. 2. Close fuel valve on engine (if available). 3. Lean unit back onto lower handles and secure in place. 4. Inspect blades for wear, and immediately replace any deformed or cracked blades. Measure the overall diameter of the blade. 5. If blades are warped or the diameter of the blade is 6.75"(171 mm) in length they must be replaced. NOTE: We recommend replacing all the blades at once. JACKSHAFT BELT REPLACEMENT 1. Wait for engine to cool and disconnect spark plug. 2. Place the rear of the unit on blocks. 3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame. 4. Remove (3) screws (item 114) holding the belt guard (item 19) in place 5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place. 6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and remove the mule assembly leaving the belt on the transmission. 7. Remove the carriage bolt and nuts holding the right bearing on the jackshaft. Do not remove the bearing and pulley. 8. Remove the belt guard (item 58) by removing the three screws (item 114). 9. Walk the belt off of the crankshaft pulley, and then slide it down the jackshaft to the bearing hole. This will allow the belt to be slid around the mule pulley. 10. Replace the belt by feeding it into the hole and around the pulley that the old one was removed. Make sure it is seated in the jackshaft pulley and then walk it onto the crankshaft pulley making sure it is inside the belt fingers. 11. Reattach the bearing and tighten the hardware securely. 12. Reattach the mule drive and belt, making sure that the belt is seated properly in the transmission pulley and the mule drive assembly. 13. Check the idler tension on the belt when the drive lever is engaged, if it is too loose the spring (item 82) holding the idler arm will need to be replaced. 14. Reattach the guards, tire, spring and spark plug and make sure of proper operation. MULE BELT REPLACEMENT 1. Wait for engine to cool and disconnect spark plug. 2. Place the rear of the unit on blocks. 3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame. 4. Remove (3) screws (item 114) holding the belt guard (item 19) in place 5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place. This will allow access to the belt. 6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and then sliding it off of the transmission. Discard old belt. 7. Install new belt using same procedure to walk the belt into the groove, making sure it is seated fully in all pulleys. Reattach the mule drive assembly. 8. With new belt installed pull the drive levers up and make sure the idler pulley puts tension on the cable. The proper adjustment should have the drive lever fully engaged and the belt should be snug on the pulleys. 9. Re-install the belt guard, spring, and tire, then reattach the spark plug. REEL BELT REPLACEMENT 1. Wait for engine to cool and disconnect spark plug. 2. Remove (2) screws (item 38) holding the belt guard (item 20) in place 3. Remove the belt (item 17) by rotating the reel pulley (item16) and walking it out of the groove. Discard old belt. 4. Install new belt using same procedure to walk the belt into the groove, making sure that it is inside the belt fingers. 5. With new belt installed push the reel drive lever down and make sure the idler pulley puts tension on the cable. The proper adjustment should have the blade lever fully engaged and the belt should be snug on the pulleys. 6. Re-install the belt guard and reattach the spark plug. Part No 351513 8 Form No F061311B OS900SP Owner’s Manual Troubleshooting P ro b le m A b n o rm a l v ib ra tio n . P o s s ib le C a u s e · D a m a g e d o r m is s in g b la d e s . L o o s e h a n d le b o lts . L o o s e e n g in e b o lts E n g in e s ta lls o r la b o rs w h e n ra k in g · B la d e s s e t to o d e e p in to g ro u n d . E n g in e w ill n o t s ta rt. · S to p s w itc h o ff (H o n d a o n ly). T h ro ttle · C h e c k c h o k e p o s itio n . in o ff p o s itio n · O u t o f g a s o lin e o r b a d , o ld g a s o lin e . · C h e c k g a s o lin e . · S p a rk P lu g w ire d is c o n n e c te d . · G a s v a lv e o ff. · D irty a ir c le a n e r. E n g in e is lo c k e d , w ill n o t p u ll o v e r. Part No 351513 · D e b ris lo c k e d a g a in s t re e l, o r d riv e p u lle ys . E n g in e p ro b le m . 9 S o lu tio n · S to p w o rk im m e d ia te ly. R e p la c e a n y d a m a g e d o r m is s in g b la d e s . T ig h te n a ll lo o s e n u ts a n d b o lts . · R a is e b la d e s s o th a t th e y ju s t to u c h th e g ro u n d o n a le v e l s u rfa c e · C o n n e c t s p a rk p lu g w ire . · T u rn o n g a s v a lv e . · C le a n o r re p la c e a ir c le a n e r. C o n ta c t a q u a lifie d s e rv ic e p e rs o n . · P u ll s p a rk p lu g w ire a n d re m o v e d e b ris . C o n ta c t a n e n g in e s e rv ic in g d e a le r fo r e n g in e p ro b le m s . Form No F061311B OS900SP Owner’s Manual SLICING REEL ASSY 351603 PARTS DRAWING 3 4 6 1 5 2 ITEM NO DESCRIPTION 1 SHAFT VERTICUTTING REEL OS900SP 2 BLADE VERTICUT OS900SP 3 SPACER PM REEL OS900SP 4 SPACER HARDENED REEL OS900SP 5 SPRING DISC 7/8" ID 6 NUT 7/8"-14 NC Part No 351513 10 PART NO. 351111 351225 351261 351297 351298 350341 QTY 1 11 10 1 1 1 Form No F061311B OS900SP Owner’s Manual ENGINE ASSEMBLY PARTS DRAWING Part No 351513 11 Form No F061311B OS900SP Owner’s Manual ENGINE ASSEMBLY PARTS LIST ITEM NO. DESCRIPTION 1 ENGINE HONDA 9HP ENGINE SUBARU 9HP 3 ENGINE BASE WA 7 JACKSHAFT WA 18 BELT ‐ 6932 POWERATED 57 BRACKET GUARD BELT UPPER 58 GUARD BELT UPPER OS900SP 78 PULLEY IDLER 4" OD X 3/8 BORE 80 ARM IDLER WA UPPER 81 PULLEY 3.50" OD X 1.00" BORE 82 SPRING IDLER UPPER 91 BOLT SHOULDER 1/2" X 2" 93 NUT LOCK 5/16"‐18 95 WASHER SPLIT LOCK 96 WASHER LOCK 7/16' S/T MED 99 SCREWCAP 7/16"‐20 X 1" HCS GR. 8 W/PATCH 101 SCREWCAP 5/16"‐24 X 1" GR 8 W/PATCH 102 SCREWCAP 3/8"‐16 X 1 3/4" HCS ZP 108 WASHER 5/16 FLAT 112 BOLT CARRIAGE 5/16"‐18 X 1 1/2" ZP 113 LOCK NUT 3/8‐16 114 SCREW SELF TAP 1/4"‐20 X 5/8" HWH TYPE F 116 WASHER 3/8" SAE 118 NUT FLANGE 5/16‐18 ZP 119 PLATE IMPELLER WASHER PB110 121 SPACER 1.25 OD X 1.010 ID X .938 THK 133 LABEL DANGER 134 SCREWCAP 5/16"‐18 X 1 3/4" HCS ZP 135 KEY SQ 1/4" X 1" 196 ENGINE BASE WA OS900SP W/LABELS 199 LABEL MADE IN U.S.A. Part No 351513 12 OS900SPH OS900SPS PART NO. QTY PART NO. QTY 430287 1 ‐ ‐ ‐ ‐ 351299 1 351100 1 351100 1 351107 1 351107 1 351211 1 351211 1 351203 1 351203 1 351116 1 351116 1 500113 1 500113 1 351113 1 351113 1 351296 1 351296 1 351275 1 351275 1 520031 1 520031 1 8160002 6 8160002 6 8177011 4 8177011 4 8177013 1 8177013 1 510213 1 510213 1 400164 4 400164 4 8041053 1 8041053 1 8171003 8 8171003 8 8024042 1 8024042 1 8160003 2 8160003 2 890359 3 890359 3 8172009 2 8172009 2 350346 2 350346 2 850443 1 850443 1 351413 2 351413 2 900327 2 900327 2 8041031 5 8041031 5 9201113 1 9201113 1 351608 1 351608 1 520116 1 520116 1 Form No F061311B OS900SP Owner’s Manual REEL/REEL DRIVE ASSEMBLY PARTS DRAWING Part No 351513 13 Form No F061311B OS900SP Owner’s Manual REEL/REEL DRIVE ASSEMBLY PARTS LIST ITEM NO. 3 4 5 13 16 17 20 21 38 41 49 54 55 68 69 76 77 91 93 95 103 104 108 118 120 124 127 129 135 138 147 150 187 191 193 DESCRIPTION ENGINE BASE WA HOUSING VERTICUTTER WA OS900SP FRAME SUPPORT OS900SP WA BEARING 3/4" CAST FLANGE W/ZERK PULLEY 0.75" ID X 4" 4L SECTION BELT 4L GUARD REEL BELT OS900SP LABEL DECAL SM CIRCLE SER HEX WASHER 3/8" ‐ 16 WASHER 1.125 OD X .344 ID X 10 GA REEL ASSY OS900SP GUARD BEARING REEL OS900SP SPACER SEED BOX AXLE OS900SP DEFLECTOR RUBBER OS900SP BAR CLAMP DEFLECTOR ARM IDLER WA REEL ENGAGE PULLEY BOLT SHOULDER 1/2" X 2" NUT LOCK 5/16"‐18 WASHER SPLIT LOCK SCREWCAP 5/16‐18 X 3 1/2" SCREWCAP 3/8"‐16 X 1" WASHER 5/16" FC NUT FLANGE 5/16‐18 ZP NUT LOCK 3/8‐16 LT WT THIN ZP SPRING IDLER MULE DRIVE SER HEX WASHER FLNG SCREW 5/16"‐18 X 3/4" BOLT CARRIAGE 5/16"‐18 X 3/4" ZP KEY 3/16" SQ X 1 1/4" CABLE CLUTCH SEEDING CONTROL PIN CLEVIS 1/4" X .50" PIN CLIP HITCH 0.051" X 3/4" SCREWCAP 3/8"‐16 X 2 1/2" ZP SCREWCAP 5/16"‐24 X 1" GR.8 ZP W/PATCH GUARD REEL BELT OS900SP W/LABELS Part No 351513 14 OS900SPH PART NO. 351100 351101 351102 350209 351210 351213 351117 890456 791080 441150 351012 351206 351408 351269 351268 351112 350114 520031 8160002 8177011 8041038 8041050 8171003 350346 8161042 351295 351264 8024039 9201080 351221 440124 440193 8041056 400164 351607 QTY 1 1 1 2 2 2 1 1 2 1 1 1 1 1 1 1 2 1 4 1 2 4 2 4 5 1 6 4 1 1 1 1 1 1 1 OS900SPS PART NO. 351100 351101 351102 350209 351210 351213 351117 890456 791080 441150 351012 351206 351408 351269 351268 351112 350114 520031 8160002 8177011 8041038 8041050 8171003 350346 8161042 351295 351264 8024039 9201080 351221 440124 440193 8041056 400164 351607 QTY 1 1 1 2 2 2 1 1 2 1 1 1 1 1 1 1 2 1 4 1 2 4 2 4 5 1 6 4 1 1 1 1 1 1 1 Form No F061311B OS900SP Owner’s Manual HANDLE ASSEMBLY PARTS DRAWING Part No 351513 15 Form No F061311B OS900SP Owner’s Manual HANDLE ASSEMBLY PARTS LIST OS900SPH ITEM NO. DESCRIPTION PART NO. 5 FRAME SUPPORT OS900SP WA 351102 28 PLUG TUBE INSERT 1.25 OD 791056 29 HANDLE FOLDING OS900SP 351406 30 BUMPER RECESS 360298 31 BRACKET CONSOLE OS900SP 351208 32 GRIP HANDLE 500267 33 PLUG TUBE INSERT 1" OD 890132 34 CONTROL MAGURA OS900SP 351209 35 LOOP FOLDING HANDLE 351231 52 PIN CLEVIS 3/8 X 2.125 520120 53 RETAINER 3/8" BOLT PUSH NUT 360279 56 LABEL INSTRUCTION OS900SP 351501 70 LEVER CLUTCH/SEED DROP 351212 500379 72 GRIP LEVER 0.125" X 1" X 5" ORANGE 102 SCREWCAP 3/8"‐16 X 1 3/4" HCS ZP 8041053 107 SCREWCAP 3/8"‐16 X 3" HCS ZP 8041058 110 BOLT CARRIAGE 3/8"‐16 X 2" ZP 8024062 113 LOCK NUT 3/8‐16 8160003 114 SCREW SELF TAP 1/4"‐20 X 5/8" HWH TYPE F 890359 115 WASHER 1/4" SAE 8172007 117 LOCK NUT 1/4‐20 8160001 128 TY WRAP 900407 131 SCREWCAP 1/4"‐20 X 1" HCS ZP 8041006 351219 136 CABLE SPEED CONTROL RT 137 CABLE SPEED CONTROL LFT 351271 138 CABLE CLUTCH SEEDING CONTROL 351221 140 LABEL LOGO OS900SP 351500 141 BOLT SHOULDER 3/8" X 1 1/4" 360284 142 LABEL CLUTCH BLADE 500177 144 WASHER 3/8 FC 8171004 194 BRACKET CONSOLE OS900SP W/LABELS 351605 Part No 351513 16 QTY 1 2 1 1 1 2 2 2 2 2 2 1 1 1 2 4 2 9 1 1 1 2 1 1 1 1 1 1 1 12 1 OS900SPS PART NO. 351102 791056 351406 360298 351208 500267 890132 351209 351231 520120 360279 351501 351212 500379 8041053 8041058 8024062 8160003 890359 8172007 8160001 900407 8041006 351219 351271 351221 351500 360284 500177 8171004 351605 QTY 1 2 1 1 1 2 2 2 2 2 2 1 1 1 2 4 2 9 1 1 1 2 1 1 1 1 1 1 1 12 1 Form No F061311B OS900SP Owner’s Manual SEED BOX ASSEMBLY PARTS DRAWING Part No 351513 17 Form No F061311B OS900SP Owner’s Manual SEED BOX ASSEMBLY PARTS LIST OS900SPH ITEM NO. DESCRIPTION PART NO. 5 FRAME SUPPORT OS900SP WA 351102 6 SEED BOX WA 351103 10 FRONT WHEEL 14" ASSY 351013 12 BEARING & FLANGETTE ASSY 850232 27 AXLE SEED BOX 351223 44 WHEEL PADDLE SEED WA 351105 45 PLATE SEED CONTROL OS900SP 351220 46 BRACKET CONTROL SEED RATE 351222 48 SPRING EXTENSION .468 X 5.25 440130 55 SPACER SEED BOX AXLE OS900SP 351408 63 SPACER SEED PLATE OS900SP 351253 64 CAM SEED RATE 351265 65 KNOB 5/16"‐18 X 5/8" FLUTED 400339 351503 66 LABEL SEED FLOW RATE 83 CLAMP ROUTING FUEL LINE 791070 100 SCREW 1/4" ‐ 20 X .75 HWH 8041004 115 WASHER 1/4" SAE 8172007 117 LOCK NUT 1/4‐20 8160001 125 NUT 5/16"‐18 SER HEX WASHER FLN 350346 129 BOLT CARRIAGE 5/16"‐18 X 3/4" ZP 8024039 138 CABLE CLUTCH SEEDING CONTROL 351221 145 LABEL WARNING OPEI 400424 147 PIN CLEVIS 1/4" X .61 350399 148 LABEL BADGING OS900SP 351505 149 WASHER LOCK 5/16" TWISTED TOOT 430298 150 PIN CLIP HITCH 0.051 X 3/4" 440193 151 BOLT CARRIAGE 5/16"‐18 X 1 1/4" ZP 8024041 152 SCREWCAP 5/16"‐18 X 3/4" HCS ZP 8041026 153 NUT LOCK 5/16"‐18 LT WT TH ZP 8161041 154 WASHER FENDER 5/16" 8172020 192 SEED BOX WAS OS900SP W/LABELS 351604 Part No 351513 18 QTY 1 1 2 4 1 1 1 1 1 2 8 1 1 1 1 8 8 8 8 8 1 1 1 1 2 1 1 2 1 2 1 OS900SPS PART NO. 351102 351103 351013 850232 351223 351105 351220 351222 440130 351408 351253 351265 400339 351503 791070 8041004 8172007 8160001 350346 8024039 351221 400424 350399 351505 430298 440193 8024041 8041026 8161041 8172020 351604 QTY 1 1 2 4 1 1 1 1 1 2 8 1 1 1 1 8 8 8 8 8 1 1 1 1 2 1 1 2 1 2 1 Form No F061311B OS900SP Owner’s Manual TRANSMISSION ASSEMBLY PARTS DRAWING Part No 351513 19 Form No F061311B OS900SP Owner’s Manual TRANSMISSION ASSEMBLY PARTS LIST ITEM NO. 2 3 5 7 11 12 14 15 16 19 22 23 24 25 26 39 40 41 42 43 50 51 59 60 61 62 75 79 84 85 86 90 91 92 93 94 95 97 102 105 106 108 111 113 114 115 116 117 Part No 351513 DESCRIPTION TRANSAXLE ENGINE BASE WA FRAME SUPPORT OS900SP WA JACKSHAFT WA REAR WHEEL13" X 5" PNEU ASSY BEARING & FLANGETTE ASSY BELT 3L540 PULLEY 0.75" ID X 2.75 PULLEY 0.75" ID X 4" 4L SECTION GUARD DRIVE BELT OS900SP BRACKET FIXED FRONT FRAME BRACKET RH WEAR PAD OS900SP BRACKET LH WEAR PAD OS900SP WEAR PAD RH OS900SP WEAR PAD LH OS900SP SPACER REAR WHEEL OS900SP WASHER .765 ID X 1.25 OD X .06 THK WASHER 1.125 OD X .344 ID X 10 GA SPEED CONTROL ASSY CONNECTOR SPEED CONTROL LEVER HEIGHT CONTROL WA GRIP LEVER LIFT LABEL DEPTH GAUGE OS900SP MULE ASSY KNOB HAND ROD BYPASS ARM TRANSAXLE SPACER PULLEY JACKSHAFT BRACKET CLUTCH CABLE LOCKNUT WA WASHER .75" STUD 3/4"‐10 X 3 3/4 PLTD BOLT SHOULDER 3/8" X 2" BOLT SHOULDER 1/2" X 2" BOLT SHOULDER 3/8" X 1/2" NUT LOCK 5/16"‐18 RING RETAINING EXTERNAL 3/4" WASHER SPLIT LOCK SCREWCAP 5/16‐24 X 1" SCREWCAP 3/8"‐16 X 1 3/4" HCS ZP SCREWCAP 5/16"‐18 X 3" HCS ZP SCREWCAP 5/16"‐18 X 2" WASHER 5/16 FLAT BOLT CARRIAGE LOCK NUT 3/8‐16 SCREW SELF TAP 1/4"‐20 X 5/8" HWH TYPE F WASHER 1/4" SAE WASHER 3/8" SAE LOCK NUT 1/4‐20 20 OS900SPH PART NO. 351201 351100 351102 351107 351202 850232 351215 351214 351210 351118 351226 351227 351228 351229 351230 351409 850238 441150 351011 351015 351106 840191 351504 ‐ 850154 351267 351415 351200 800227 800109 351272 360153 520031 830528 8160002 850230 8177011 400164 8041053 8041036 8041032 8171003 9024047 8160003 890359 8172007 8172009 8160001 QTY 1 1 1 1 2 4 1 1 1 1 2 1 1 1 1 2 2 1 1 1 1 1 1 ‐ 1 1 1 1 1 1 1 2 1 2 10 2 6 2 1 4 1 4 4 4 5 10 3 6 OS900SPS PART NO. 351201 351100 351102 351107 351202 850232 351215 351214 351210 351118 351226 351227 351228 351229 351230 351409 850238 441150 351011 351015 351106 840191 351504 ‐ 850154 351267 351415 351200 800227 800109 351272 360153 520031 830528 8160002 850230 8177011 400164 8041053 8041036 8041032 8171003 9024047 8160003 890359 8172007 8172009 8160001 QTY 1 1 1 1 2 4 1 1 1 1 2 1 1 1 1 2 2 1 1 1 1 1 1 ‐ 1 1 1 1 1 1 1 2 1 2 10 2 6 2 1 4 1 4 4 4 5 10 3 6 Form No F061311B OS900SP Owner’s Manual TRANSMISSION ASSEMBLY PARTS LIST ITEM NO. 123 125 126 129 131 135 136 137 139 143 146 150 153 154 155 157 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 177 178 179 180 182 183 186 189 195 197 198 Part No 351513 DESCRIPTION BRACKET TORQUE LIMITING NUT 5/16"‐18 SER HEX WASHER FLNG ZP SCREW SPOT WELD 5/16"‐18 X 3/4 W/PROJ BOLT CARRIAGE 5/16"‐18 X 3/4" ZP SCREWCAP 1/4"‐20 X 1" HCS ZP KEY 3/16" SQ X 1 1/4" CABLE SPEED CONTROL RT CABLE SPEED CONTROL LFT SCREWCAP 5/16" SER HEX WSHR FLNG GR. 5 ZP GROMMET 1.25" HOLE LABEL DRIVE RELEASE OS900SP PIN CLIP HITCH 0.051 X 3/4" NUT LOCK 5/16"‐18 LT WT TH ZP WASHER FENDER 5/16" SPRING LIFT ASSIST OS900SP SCREW MACH #10‐24 X 2" HWF ZP SPACER EYELET SPEED CONTROL OS900SP BEARING 1/2" ID X 1.125 OD BOLT SHOULDER 3/8" X 1 3/4" BRACKET SPEED CONTROL WA OS900SP BELLCRANK SPEED CONTROL WA OS900SP CAM SPEED CONTROL WA BUSHING PIVOT FRAME AE BOLT SHOULDER 5/16" X 1 1/2" SPRING EXTENSION BUSHING 3/8" ID X 1/2" OD X 3/8" SCREWCAP 1/4‐20 X 1 3/4 SKT BUT HD NUT LOCK 5/8"‐11 LT WT TH ZP WASHER 5/8" SAE SCREWCAP 5/16"‐18 X 1" HCS ZP PULLEY IDLER 2.75" OD X 3/8" BORE BRACKET DRIVE BELT WA OS900SP PULLEY 3V GROOVE IDLER BOLT SHOULDER 1/2" X 2" ARM IDLER MULE DRIVE WA OS900SP SPRING IDLER MULE DRIVE OS900SP SCREWCAP 3/8"‐16 X 1 1/2" HCS ZP WASHER #10 SAE KEY 3/16" SQ X 2 1/8" SCREWCAP 5/16"‐18 X 5" HCS ZP KEY 3/16" SQ X 5/8" FRAME SUPPORT OS900SP WA W/LABELS DRIVE BELT GUARD WA W/LABELS BRACKET BELT GUIDE OSSP 21 OS900SPH PART NO. 351294 350346 351263 8024039 8041006 9201080 351219 351271 351264 520092 351507 440193 8161041 8172020 351254 8059143 351256 351257 351258 351108 351109 351110 360183 500340 800242 840078 840199 8161046 8172013 8041028 350114 351104 351216 520031 351120 351302 8041052 8172005 9201087 8041042 9201072 351606 351609 351300 QTY 1 7 4 5 4 1 1 1 8 1 1 1 2 1 2 1 2 2 2 1 2 1 2 1 2 4 2 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 OS900SPS PART NO. 351294 350346 351263 8024039 8041006 9201080 351219 351271 351264 520092 351507 440193 8161041 8172020 351254 8059143 351256 351257 351258 351108 351109 351110 360183 500340 800242 840078 840199 8161046 8172013 8041028 350114 351104 351216 520031 351120 351302 8041052 8172005 9201087 8041042 9201072 351606 351609 351300 QTY 1 7 4 5 4 1 1 1 8 1 1 1 2 1 2 1 2 2 2 1 2 1 2 1 2 4 2 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 Form No F061311B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Author : FlorenceJ Create Date : 2011:06:15 14:59:38-05:00 Modify Date : 2011:10:21 13:09:35-05:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2011:10:21 13:09:35-05:00 Document ID : uuid:81e52a3d-fa43-487a-a918-2136c7dd36f3 Instance ID : uuid:1f8364cc-200c-4b80-baed-7c7722729861 Format : application/pdf Title : Microsoft Word - 351513 F061311B OSSP OPER MANUAL Creator : FlorenceJ Page Count : 21EXIF Metadata provided by EXIF.tools