351513 F061311B OSSP OPER MANUAL !! 1 Os900sps
Preview ! 351513-1_os900sps Billy Goat Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
User Manual: !! Billy Goat Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
Open the PDF directly: View PDF 
.
Page Count: 21
Part No 351513 Form No F061311B
1
OS900SP Owner’s Manual
Unit shown with Seed Box Lid, sold separately
BILLY GOAT SELF PROPELLED OVERSEEDER
OS900SPS, OS900SPH
Owner's Manual
Accessories Replacement Parts
Seed Box Lid Kit
Chariot Kit
Reel Kit
A convenient way to
enclose the seed box
P/N 351600
Allows the user to ride
behind the unit and
decrease fatigue from
walking
P/N 351601
Use to replace worn or
damaged reels
P/N 351603
Part No 351513 Form No F061311B
2
OS900SP Owner’s Manual
CONTENTS
SPECIFICATIONS AND SOUND/VIBRATION ___ 3
INSTRUCTION LABELS 4
PACKING CHECKLIST & ASSEMBLY 5
OPERATION 6-7
MAINTENANCE 8
TROUBLESHOOTING____________________________ 9
PARTS LIST____________ 10-21
Part No 351513 Form No F061311B
3
OS900SP Owner’s Manual
Specifications
OS900SPS OS900SPH
Engine: HP’ 9.0 HP (6.7kW) 9.0 HP (6.7kW)
Engine: Model EX270D50021 GX270K1QA2
Engine: Type Subaru Honda
Engine: Fuel Capacity 6.4 qt. (6.1 L) 5.6 qt. (5.3 L)
Engine: Oil Capacity 1.06 qt. (1 L) 1.16 qt. (1.1 L)
Total Unit Weight: 314# (142 kg) 323# (147 kg)
Max. operating slope 15o 20o
Sound test in accordance with 2000/14/EC 104 dB(a) 104 dB(a)
Sound at operators ear 84 dB(a) 84 dB(a)
Vibration at operator position 0.81g (7.95 m/s2) 0.81g (7.95 m/s2)
SOUND
SOUND LEVEL 84 dB(a) at Operators Position
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 10-13-2010 under the conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound
power level for your model.
VIBRATION DATA
VIBRATION LEVEL .81g (7.95m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test
equipment. Tests were performed on 10-13-2010 under the conditions listed below.
General Conditions: Sunny
Temperature: 73oF (23oC)
Wind Speed: 11 mph (17 kmh)
Wind Direction: South West
Humidity: 27%
Barometric Pressure: 30.34Hg (770 mm Hg)
General Conditions: Sunny
Temperature: 66oF (19oC)
Wind Speed: 3 mph (4.8kph)
Wind Direction: East
Humidity: 30.2%
Barometric Pressure: 29.9Hg (101.3kpa)
104
Part No 351513 Form No F061311B
4
OS900SP Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ® Overseeder. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS LABEL CLUTCH ITEM #142 LABEL TRANS. RELEASE
AND FEET AWAY P/N 500177 ITEM #146 P/N 351507
ITEM #145 P/N 400424
LABEL CAUTION GUARDS LABEL DEPTH GAUGE
ITEM #133 P/N 900327 ITEM #59 P/N 351504
LABEL INSTRUCTIONS SEEDER BOX LABEL SEED METERING
ITEM #56 P/N 351501 ITEM #66 P/N 351503
(page 12) (page 12)
ENGINE LABELS
.
SUBARU HONDA
HONDA MOTOR CO. , LTD. MADE IN JAPAN
READ OWNER’S MANUAL BEFORE OPERATION.
LIRE LE MANUEL D UTILISATEUR AVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL
WHEN OIL LEVEL LOW,
ENGINE STOPS IMMEDIATELY.
OIL ALERT
Part No 351513 Form No F061311B
5
OS900SP Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Overseeder is shipped from the factory in one carton, completely assembled.
PUT OIL IN ENGINE BEFORE STARTING
ASSEMBLY
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the
unit and cables could snag.
1. UNFOLD the upper handle and slide handle lock loops (item 35) into place to secure the upper handle to the
lower.
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move
height adjust lever to down position, to level engine during checking. See engine manufacturers’ instruction
manual.
3. CONNECT spark plug wire.
Boxing Parts
Checklist
Subaru 9 HP
Honda 9 OHV
Parts bag
P/N-351009
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-351513, General Safety and Warnings Manual P/N-
1
00
2
95,
D
ec
l
a
r
at
i
o
n
o
f
Co
nf
o
rmi
ty
P
/
N-
35
1
508
.
Part No 351513 Form No F061311B
6
OS900SP Owner’s Manual
OPERATION
ADJUSTING BLADE DEPTH
The depth of the blades can be raised or lowered by rotating the knob
located at the rear of the machine. The relative depth of the blades can be
gauged by using the depth scale located on the rear of the machine and the
bar next to it.
SLICING TIPS
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core
samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe.
Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to
determine the depth of thatch in your yard.
THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time
at the base of the lawn preventing air, water, and fertilizer from reaching the soil. This can
cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of
thatch will keep your lawn in good health.
HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments
for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in
one treatment will damage or destroy the living part of the lawn. It is best to remove heavy
thatch in seasonal treatments (i.e. spring, and fall).
SLOPES: Rake slopes across not up and down. This is much easier and safer for the operator
and is better for the lawn. Raking across will help to reduce runoff during watering and allow
the sloped ground to hold more seed, fertilizer, and water. The unit’s maximum operating slope
is 35% or 19°.
DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear.
Setting the reel deeper will not produce better, or quicker results. The slicing reel should be set
even with the ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding
jobs. Setting the reel deeper than this will only result in premature wear on the unit (i.e. failed
belt). If you desire to work the ground deeper than the above guidelines allow, it should be
done gradually in multiple passes..
VERTICUTTING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before
starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in criss-
cross pattern (See Fig. 1 and See Fig 2).
FOLDING HANDLE
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by
sliding the handle lock loops (item 35) up. This releases the upper handle, allowing it to be folded over the unit.
BLADE POSITION & DEPTH CONTROL LEVER
The blades can be raised or lowered into the ground by height adjustment lever
at the rear of the unit. The blades will be in their lowered position when the lever
is to the left and should be locked in the notch on the right when in transport. The
resulting blade depth can be adjusted higher or lower.
See ADJUSTING BLADE DEPTH above.
Fig. 1
Fig. 2
Part No 351513 Form No F061311B
7
OS900SP Owner’s Manual
VERTI-CUTTING OPERATION
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface
(i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE BLADES: Push the Reel Lever down on the operators handle (upper left side).
NOTE: When engaging the blades in heavy load conditions (i.e. heavy thatch, or very uneven
turf), push down on the operators handle lifting the front wheels slightly. Engage the blades.
Slowly lower the unit into the turf.
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should
be removed and deposited on top of the healthy grass. Grass runners should be cut and ready
for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease
damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or bounces during operation the blade depth is set
too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited
over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection
and removal of the thatch/stems.
OVERSEEDING OPERATION
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5
kg. per 93 m2 ]) Adjustments to the seed drop is located on the front of the unit on the seed dial and
should be used in conjunction with the seed chart on the console.
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm)
below a flat surface (i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE REEL AND SEED DROP: Push down on the Reel lever on the operators handle. NOTE:
When engaging the reel in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down
on the operators handle lifting the front wheels slightly. Engage the reel. Slowly lower the unit into
the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If
excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue
raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in
engine RPM occurs, or bounces during operation the blade depth is set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to
the seed su
pp
liers directions.
ADJUSTING SEED RATE
INSTRUCTION LABEL P/N 351501
To set the seed flow rate, loosen the knob on
the indicator dial and set it to the
corresponding stop setting on the seed
application chart (below or on the console) for
the type and amount of seed being used.
Part No 351513 Form No F061311B
8
OS900SP Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every Use (daily) Every 25 Hours
Inspect for loose, worn or damaged parts. z
Check engine oil z
Inspect belts z
Engine (See Engine Manual)
Grease bearings z
Inspect and clean engine air filter z
Oil height adjustment linkage z
SLICING BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any deformed or cracked blades.
Measure the overall diameter of the blade.
5. If blades are warped or the diameter of the blade is 6.75"(171 mm) in length they must be
replaced. NOTE: We recommend replacing all the blades at once.
JACKSHAFT BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove (3) screws (item 114) holding the belt guard (item 19) in place
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place.
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and remove the mule assembly leaving the belt on the
transmission.
7. Remove the carriage bolt and nuts holding the right bearing on the jackshaft. Do not remove the bearing and pulley.
8. Remove the belt guard (item 58) by removing the three screws (item 114).
9. Walk the belt off of the crankshaft pulley, and then slide it down the jackshaft to the bearing hole. This will allow the belt to be slid around the mule
pulley.
10. Replace the belt by feeding it into the hole and around the pulley that the old one was removed. Make sure it is seated in the jackshaft pulley and
then walk it onto the crankshaft pulley making sure it is inside the belt fingers.
11. Reattach the bearing and tighten the hardware securely.
12. Reattach the mule drive and belt, making sure that the belt is seated properly in the transmission pulley and the mule drive assembly.
13. Check the idler tension on the belt when the drive lever is engaged, if it is too loose the spring (item 82) holding the idler arm will need to be
replaced.
14. Reattach the guards, tire, spring and spark plug and make sure of proper operation.
REEL BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Remove (2) screws (item 38) holding the belt guard (item 20) in place
3. Remove the belt (item 17) by rotating the reel pulley (item16) and walking it out of the groove. Discard old belt.
4. Install new belt using same procedure to walk the belt into the groove, making sure that it is inside the belt fingers.
5. With new belt installed push the reel drive lever down and make sure the idler pulley puts tension on the cable. The proper adjustment should have
the blade lever fully engaged and the belt should be snug on the pulleys.
6. Re-install the belt guard and reattach the spark plug.
MULE BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place the rear of the unit on blocks.
3. Remove the right rear tire (item 11) and spring (item 155) attaching the housing to the frame.
4. Remove (3) screws (item 114) holding the belt guard (item 19) in place
5. Remove the four screws (item 107) holding the mule drive assembly (item 60) in place. This will allow access to the belt.
6. Remove the belt (item 14) by rotating the mule drive pulley and walking it out of the groove, and then sliding it off of the transmission. Discard old
belt.
7. Install new belt using same procedure to walk the belt into the groove, making sure it is seated fully in all pulleys. Reattach the mule drive assembly.
8. With new belt installed pull the drive levers up and make sure the idler pulley puts tension on the cable. The proper adjustment should have the drive
lever fully engaged and the belt should be snug on the pulleys.
9. Re-install the belt guard, spring, and tire, then reattach the spark plug.
Part No 351513 Form No F061311B
9
OS900SP Owner’s Manual
Troubleshooting
Problem Possible Cause Solution
Abnormal vibration. · Damaged or missing blades. Loose
handle bolts. Loose engine bolts
· Stop work immediately. Replace any
damaged or missing blades. Tighten all
loose nuts and bolts.
Engine stalls or labors when
raking
· Blades set too deep into ground. · Raise blades so that they just touch the
ground on a level surface
Engine will not start. · Stop switch off (Honda only). Throttle
in off position
· Check choke position.
· Out of gasoline or bad, old gasoline. · Check gasoline.
· Spark Plug wire disconnected. · Connect spark plug wire.
· Gas valve off. · Turn on gas valve.
· Dirty air cleaner. · Clean or replace air cleaner. Contact a
qualified service person.
Engine is locked, will not pull
over.
· Debris locked against reel, or drive
pulleys. Engine problem.
· Pull spark plug wire and remove debris.
Contact an engine servicing dealer for
engine problems.
Part No 351513 Form No F061311B
10
OS900SP Owner’s Manual
SLICING REEL ASSY 351603
PARTS DRAWING
6
5
4
3
2
1
ITEM NO DESCRIPTION PART NO. QTY
1 SHAFT VERTICUTTING REEL OS900SP 351111 1
2 BLADE VERTICUT OS900SP 351225 11
3 SPACER PM REEL OS900SP 351261 10
4 SPACER HARDENED REEL OS900SP 351297 1
5 SPRING DISC 7/8" ID 351298 1
6 NUT 7/8"-14 NC 350341 1
Part No 351513 Form No F061311B
11
OS900SP Owner’s Manual
ENGINE ASSEMBLY PARTS DRAWING
Part No 351513 Form No F061311B
12
OS900SP Owner’s Manual
ENGINE ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QT
Y
PARTNO. QTY
1ENGINEHONDA9HP430287 1 ‐‐
ENGINESUBARU9HP ‐‐351299 1
3ENGINEBASEWA 351100 1 351100 1
7JACKSHAFTWA 351107 1 351107 1
18 BELT‐6932POWERATED 351211 1 351211 1
57 BRACKETGUARDBELTUPPER 351203 1 351203 1
58 GUARDBELTUPPEROS900SP 351116 1 351116 1
78 PULLEYIDLER4"ODX3/8BORE 500113 1 500113 1
80 ARMIDLERWAUPPER 351113 1 351113 1
81 PULLEY3.50"ODX1.00"BORE 351296 1 351296 1
82 SPRINGIDLERUPPER 351275 1 351275 1
91 BOLTSHOULDER1/2"X2" 520031 1 520031 1
93 NUTLOCK5/16"‐18 8160002 6 8160002 6
95 WASHERSPLITLOCK8177011 4 8177011 4
96 WASHERLOCK7/16'S/TMED 8177013 1 8177013 1
99 SCREWCAP7/16"‐20X1"HCSGR.8W/PATCH 510213 1 510213 1
101 SCREWCAP5/16"‐24X1"GR8W/PATCH 400164 4 400164 4
102 SCREWCAP3/8"‐16X13/4"HCSZP 8041053 1 8041053 1
108 WASHER5/16FLAT 8171003 8 8171003 8
112 BOLTCARRIAGE5/16"‐18X11/2"ZP 8024042 1 8024042 1
113 LOCKNUT3/8‐16 8160003 2 8160003 2
114 SCREWSELFTAP1/4"‐20X5/8"HWHTYPEF 890359 3 890359 3
116 WASHER3/8"SAE 8172009 2 8172009 2
118 NUTFLANGE5/16‐18ZP 350346 2 350346 2
119 PLATEIMPELLERWASHERPB110 850443 1 850443 1
121 SPACER1.25ODX1.010IDX.938THK 351413 2 351413 2
133 LABELDANGER 900327 2 900327 2
134 SCREWCAP5/16"‐18X13/4"HCSZP 8041031 5 8041031 5
135 KEYSQ1/4"X1" 9201113 1 9201113 1
196 ENGINEBASEWAOS900SPW/LABELS 351608 1 351608 1
199 LABELMADEINU.S.A. 520116 1 520116 1
Part No 351513 Form No F061311B
13
OS900SP Owner’s Manual
REEL/REEL DRIVE ASSEMBLY PARTS DRAWING
Part No 351513 Form No F061311B
14
OS900SP Owner’s Manual
REEL/REEL DRIVE ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QT
Y
PARTNO. QTY
3ENGINEBASEWA 351100 1 351100 1
4HOUSINGVERTICUTTERWAOS900SP 351101 1 351101 1
5FRAMESUPPORTOS900SPWA 351102 1 351102 1
13 BEARING3/4"CASTFLANGEW/ZERK 350209 2 350209 2
16 PULLEY0.75"IDX4"4LSECTION 351210 2 351210 2
17 BELT4L 351213 2 351213 2
20 GUARDREELBELTOS900SP 351117 1 351117 1
21 LABELDECALSMCIRCLE 890456 1 890456 1
38 SERHEXWASHER3/8"‐16 791080 2 791080 2
41 WASHER1.125ODX.344IDX10GA 441150 1 441150 1
49 REELASSYOS900SP 351012 1 351012 1
54 GUARDBEARINGREELOS900SP 351206 1 351206 1
55 SPACERSEEDBOXAXLEOS900SP 351408 1 351408 1
68 DEFLECTORRUBBEROS900SP 351269 1 351269 1
69 BARCLAMPDEFLECTOR 351268 1 351268 1
76 ARMIDLERWAREELENGAGE 351112 1 351112 1
77 PULLEY 350114 2 350114 2
91 BOLTSHOULDER1/2"X2" 520031 1 520031 1
93 NUTLOCK5/16"‐18 8160002 4 8160002 4
95 WASHERSPLITLOCK8177011 1 8177011 1
103 SCREWCAP5/16‐18X31/2" 8041038 2 8041038 2
104 SCREWCAP3/8"‐16X1" 8041050 4 8041050 4
108 WASHER5/16"FC 8171003 2 8171003 2
118 NUTFLANGE5/16‐18ZP 350346 4 350346 4
120 NUTLOCK3/8‐16LTWTTHINZP 8161042 5 8161042 5
124 SPRINGIDLERMULEDRIVE 351295 1 351295 1
127 SERHEXWASHERFLNGSCREW5/16"‐18X3/4" 351264 6 351264 6
129 BOLTCARRIAGE5/16"‐18X3/4"ZP 8024039 4 8024039 4
135 KEY3/16"SQX11/4" 9201080 1 9201080 1
138 CABLECLUTCHSEEDINGCONTROL351221 1 351221 1
147 PINCLEVIS1/4"X.50" 440124 1 440124 1
150 PINCLIPHITCH0.051"X3/4" 440193 1 440193 1
187 SCREWCAP3/8"‐16X21/2"ZP 8041056 1 8041056 1
191 SCREWCAP5/16"‐24X1"GR.8ZPW/PATCH 400164 1 400164 1
193 GUARDREELBELTOS900SPW/LABELS 351607 1 351607 1
Part No 351513 Form No F061311B
15
OS900SP Owner’s Manual
HANDLE ASSEMBLY PARTS DRAWING
Part No 351513 Form No F061311B
16
OS900SP Owner’s Manual
HANDLE ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QTY PARTNO. QTY
5FRAMESUPPORTOS900SPWA 351102 1 351102 1
28 PLUGTUBEINSERT1.25OD 791056 2 791056 2
29 HANDLEFOLDINGOS900SP 351406 1 351406 1
30 BUMPERRECESS 360298 1 360298 1
31 BRACKETCONSOLEOS900SP 351208 1 351208 1
32 GRIPHANDLE500267 2 500267 2
33 PLUGTUBEINSERT1"OD 890132 2 890132 2
34 CONTROLMAGURAOS900SP 351209 2 351209 2
35 LOOPFOLDINGHANDLE 351231 2 351231 2
52 PINCLEVIS3/8X2.125 520120 2 520120 2
53 RETAINER3/8"BOLTPUSHNUT 360279 2 360279 2
56 LABELINSTRUCTIONOS900SP 351501 1 351501 1
70 LEVERCLUTCH/SEEDDROP 351212 1 351212 1
72 GRIPLEVER0.125"X1"X5"ORANGE 500379 1 500379 1
102 SCREWCAP3/8"‐16X13/4"HCSZP 8041053 2 8041053 2
107 SCREWCAP3/8"‐16X3"HCSZP 8041058 4 8041058 4
110 BOLTCARRIAGE3/8"‐16X2"ZP 8024062 2 8024062 2
113 LOCKNUT3/8‐16 8160003 9 8160003 9
114 SCREWSELFTAP1/4"‐20X5/8"HWHTYPEF 890359 1 890359 1
115 WASHER1/4"SAE 8172007 1 8172007 1
117 LOCKNUT1/4‐20 8160001 1 8160001 1
128 TYWRAP 900407 2 900407 2
131 SCREWCAP1/4"‐20X1"HCSZP 8041006 1 8041006 1
136 CABLESPEEDCONTROLRT 351219 1 351219 1
137 CABLESPEEDCONTROLLFT 351271 1 351271 1
138 CABLECLUTCHSEEDINGCONTROL 351221 1 351221 1
140 LABELLOGOOS900SP 351500 1 351500 1
141 BOLTSHOULDER3/8"X11/4" 360284 1 360284 1
142 LABELCLUTCHBLADE 500177 1 500177 1
144 WASHER3/8FC 8171004 12 8171004 12
194 BRACKETCONSOLEOS900SPW/LABELS 351605 1 351605 1
Part No 351513 Form No F061311B
17
OS900SP Owner’s Manual
SEED BOX ASSEMBLY PARTS DRAWING
Part No 351513 Form No F061311B
18
OS900SP Owner’s Manual
SEED BOX ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QT
Y
PARTNO. QT
Y
5FRAMESUPPORTOS900SPWA 351102 1 351102 1
6SEEDBOXWA 351103 1 351103 1
10 FRONTWHEEL14"ASSY351013 2 351013 2
12 BEARING&FLANGETTEASSY 850232 4 850232 4
27 AXLESEEDBOX 351223 1 351223 1
44 WHEELPADDLESEEDWA 351105 1 351105 1
45 PLATESEEDCONTROLOS900SP 351220 1 351220 1
46 BRACKETCONTROLSEEDRATE 351222 1 351222 1
48 SPRINGEXTENSION.468X5.25 440130 1 440130 1
55 SPACERSEEDBOXAXLEOS900SP 351408 2 351408 2
63 SPACERSEEDPLATEOS900SP 351253 8 351253 8
64 CAMSEEDRATE351265 1 351265 1
65 KNOB5/16"‐18X5/8"FLUTED 400339 1 400339 1
66 LABELSEEDFLOWRATE 351503 1 351503 1
83 CLAMPROUTINGFUELLINE 791070 1 791070 1
100 SCREW1/4"‐20X.75HWH 8041004 8 8041004 8
115 WASHER1/4"SAE 8172007 8 8172007 8
117 LOCKNUT1/4‐20 8160001 8 8160001 8
125 NUT5/16"‐18SERHEXWASHERFLN 350346 8 350346 8
129 BOLTCARRIAGE5/16"‐18X3/4"ZP 8024039 8 8024039 8
138 CABLECLUTCHSEEDINGCONTROL 351221 1 351221 1
145 LABELWARNINGOPEI 400424 1 400424 1
147 PINCLEVIS1/4"X.61 350399 1 350399 1
148 LABELBADGINGOS900SP 351505 1 351505 1
149 WASHERLOCK5/16"TWISTEDTOO
T
430298 2 430298 2
150 PINCLIPHITCH0.051X3/4" 440193 1 440193 1
151 BOLTCARRIAGE5/16"‐18X11/4"Z
P
8024041 1 8024041 1
152 SCREWCAP5/16"‐18X3/4"HCSZP 8041026 2 8041026 2
153 NUTLOCK5/16"‐18LTWTTHZP 8161041 1 8161041 1
154 WASHERFENDER5/16" 8172020 2 8172020 2
192 SEEDBOXWASOS900SPW/LABELS 351604 1 351604 1
Part No 351513 Form No F061311B
19
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS DRAWING
Part No 351513 Form No F061311B
20
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QTY PARTNO. QTY
2 TRANSAXLE 351201 1 351201 1
3ENGINEBASEWA 351100 1 351100 1
5FRAMESUPPORTOS900SPWA 351102 1 351102 1
7JACKSHAFTWA 351107 1 351107 1
11 REARWHEEL13"X5"PNEUASSY 351202 2 351202 2
12 BEARING&FLANGETTEASSY 850232 4 850232 4
14 BELT3L540 351215 1 351215 1
15 PULLEY0.75"IDX2.75 351214 1 351214 1
16 PULLEY0.75"IDX4"4LSECTION 351210 1 351210 1
19 GUARDDRIVEBELTOS900SP 351118 1 351118 1
22 BRACKETFIXEDFRONTFRAME 351226 2 351226 2
23 BRACKETRHWEARPADOS900SP 351227 1 351227 1
24 BRACKETLHWEARPADOS900SP 351228 1 351228 1
25 WEARPADRHOS900SP 351229 1 351229 1
26 WEARPADLHOS900SP 351230 1 351230 1
39 SPACERREARWHEELOS900SP 351409 2 351409 2
40 WASHER.765IDX1.25ODX.06THK 850238 2 850238 2
41 WASHER1.125ODX.344IDX10GA 441150 1 441150 1
42 SPEEDCONTROLASSY 351011 1 351011 1
43 CONNECTORSPEEDCONTROL 351015 1 351015 1
50 LEVERHEIGHTCONTROLWA 351106 1 351106 1
51 GRIPLEVERLIFT 840191 1 840191 1
59 LABELDEPTHGAUGEOS900SP 351504 1 351504 1
60 MULEASSY ‐‐‐‐
61 KNOBHAND850154 1 850154 1
62 RODBYPASSARMTRANSAXLE 351267 1 351267 1
75 SPACERPULLEYJACKSHAFT 351415 1 351415 1
79 BRACKETCLUTCHCABLE351200 1 351200 1
84 LOCKNUTWA800227 1 800227 1
85 WASHER.75" 800109 1 800109 1
86 STUD3/4"‐10X33/4PLTD 351272 1 351272 1
90 BOLTSHOULDER3/8"X2" 360153 2 360153 2
91 BOLTSHOULDER1/2"X2" 520031 1 520031 1
92 BOLTSHOULDER3/8"X1/2" 830528 2 830528 2
93 NUTLOCK5/16"‐18 8160002 10 8160002 10
94 RINGRETAININGEXTERNAL3/4" 850230 2 850230 2
95 WASHERSPLITLOCK8177011 6 8177011 6
97 SCREWCAP5/16‐24X1" 400164 2 400164 2
102 SCREWCAP3/8"‐16X13/4"HCSZP 8041053 1 8041053 1
105 SCREWCAP5/16"‐18X3"HCSZP 8041036 4 8041036 4
106 SCREWCAP5/16"‐18X2" 8041032 1 8041032 1
108 WASHER5/16FLAT 8171003 4 8171003 4
111 BOLTCARRIAGE9024047 4 9024047 4
113 LOCKNUT3/8‐16 8160003 4 8160003 4
114 SCREWSELFTAP1/4"‐20X5/8"HWHTYPEF 890359 5 890359 5
115 WASHER1/4"SAE 8172007 10 8172007 10
116 WASHER3/8"SAE 8172009 3 8172009 3
117 LOCKNUT1/4‐20 8160001 6 8160001 6
Part No 351513 Form No F061311B
21
OS900SP Owner’s Manual
TRANSMISSION ASSEMBLY PARTS LIST
OS900SPH OS900SPS
ITEMNO. DESCRIPTIONPARTNO. QT
Y
PARTNO. QT
Y
123 BRACKETTORQUELIMITING351294 1 351294 1
125 NUT5/16"‐18SERHEXWASHERFLNGZP 350346 7 350346 7
126 SCREWSPOTWELD5/16"‐18X3/4W/PROJ 351263 4 351263 4
129 BOLTCARRIAGE5/16"‐18X3/4"ZP 8024039 5 8024039 5
131 SCREWCAP1/4"‐20X1"HCSZP 8041006 4 8041006 4
135 KEY3/16"SQX11/4" 9201080 1 9201080 1
136 CABLESPEEDCONTROLRT 351219 1 351219 1
137 CABLESPEEDCONTROLLFT 351271 1 351271 1
139 SCREWCAP5/16"SERHEXWSHRFLNGGR.5ZP 351264 8 351264 8
143 GROMMET1.25"HOLE 520092 1 520092 1
146 LABELDRIVERELEASEOS900SP 351507 1 351507 1
150 PINCLIPHITCH0.051X3/4" 440193 1 440193 1
153 NUTLOCK5/16"‐18LTWTTHZP 8161041 2 8161041 2
154 WASHERFENDER5/16" 8172020 1 8172020 1
155 SPRINGLIFTASSISTOS900SP 351254 2 351254 2
157 SCREWMACH#10‐24X2"HWFZP 8059143 1 8059143 1
159 SPACEREYELETSPEEDCONTROLOS900SP 351256 2 351256 2
160 BEARING1/2"IDX1.125OD 351257 2 351257 2
161 BOLTSHOULDER3/8"X13/4" 351258 2 351258 2
162 BRACKETSPEEDCONTROLWAOS900SP 351108 1 351108 1
163 BELLCRANKSPEEDCONTROLWAOS900SP 351109 2 351109 2
164 CAMSPEEDCONTROLWA 351110 1 351110 1
165 BUSHINGPIVOTFRAMEAE 360183 2 360183 2
166 BOLTSHOULDER5/16"X11/2" 500340 1 500340 1
167 SPRINGEXTENSION 800242 2 800242 2
168 BUSHING3/8"IDX1/2"ODX3/8" 840078 4 840078 4
169 SCREWCAP1/4‐20X13/4SKTBUTHD 840199 2 840199 2
170 NUTLOCK5/8"‐11LTWTTHZP 8161046 1 8161046 1
171 WASHER5/8"SAE 8172013 1 8172013 1
172 SCREWCAP5/16"‐18X1"HCSZP 8041028 2 8041028 2
173 PULLEYIDLER2.75"ODX3/8"BORE 350114 1 350114 1
174 BRACKETDRIVEBELTWAOS900SP 351104 1 351104 1
175 PULLEY3VGROOVEIDLER 351216 1 351216 1
177 BOLTSHOULDER1/2"X2" 520031 1 520031 1
178 ARMIDLERMULEDRIVEWAOS900SP 351120 1 351120 1
179 SPRINGIDLERMULEDRIVEOS900SP 351302 1 351302 1
180 SCREWCAP3/8"‐16X11/2"HCSZP 8041052 1 8041052 1
182 WASHER#10SAE 8172005 1 8172005 1
183 KEY3/16"SQX21/8" 9201087 2 9201087 2
186 SCREWCAP5/16"‐18X5"HCSZP 8041042 1 8041042 1
189 KEY3/16"SQX5/8" 9201072 1 9201072 1
195 FRAMESUPPORTOS900SPWAW/LABELS 351606 1 351606 1
197 DRIVEBELTGUARDWAW/LABELS 351609 1 351609 1
198 BRACKETBELTGUIDEOSSP 351300 1 351300 1
