Ph30.2 49200 Ads Owners Manual

PH30.2 to the manual 95d42e39-284f-4cfe-9f9c-8bd3219dbc7d

User Manual: PH30.2

Open the PDF directly: View PDF PDF.
Page Count: 24

DownloadPh30.2 49200 Ads Owners Manual
Open PDF In BrowserView PDF
front_cover.qxd

10/26/56

5:13 AM

Page 2

PH30.2
owner's manual

analog and digital systems

table of contents
introduction
about this manual
features of your PowerPlate™
warning and tips
mounting locations
system planning
system configurations
amplifier and crossover controls
installation
controls and connections
signal sources
internal signal routing
multi-cross™ crossover and configurations
constant bass control
AC502 operation
tuning
troubleshooting
specifications
warranty information

1
2
2
3
3
4
5-9
10-11
12
12-13
14
15
16
17
17
17-18
19-20
21
22

introduction
Although it may be hard to remember, back in the 1970’s, car audio as we now know it didn’t really exist.
Sure, music lovers could buy a cassette or 8-track tape deck and some 6" x 9" three-way speakers.
Advanced stereo buffs might even add a "power-booster" to increase output too as much as 12 watts
RMS! But none of this really delivered the power to cut through road noise with sound quality that
compared with the best home audio. Not until 1979 that is, when a/d/s/ introduced the revolutionary
PowerPlate™ P100 amplifier and 300i 2-way plate loudspeakers. Aesthetically, the P100 introduced the
low profile design which has been an a/d/s/ trademark to this day. Technologically, the P100 combined a
high efficiency switching power supply with a state-of-the-art, discrete high-current stereo power
amplifier. For the first time, a car audio system existed with the musical integrity and dynamic range that
made you want to take long drives to nowhere, just to listen to the music. High quality car audio was
born, and the original a/d/s/ PowerPlate™ P100 made it happen.
The latest improvements to the PowerPlate™ line-up include increased heatsink area to facilitate higher
power output, Constant Bass circuit for subwoofer signal that can be mixed into all channels, and fully
balanced high-level inputs compatible with any source. The amplifier you have purchased is an
enhancement of the respected P-series multichannel amplifiers. In this version, we have improved upon
the already acclaimed sound quality by addressing internal details, and upgrading selected components
to incorporate the latest technology which was not available when the P-series was originally designed.
Selected low-noise, high-speed Burr-Brown® op amps are used in critical circuits. Class-A biasing is used
throughout the voltage-gain and active crossover stages. Numerous modifications and "tweaks" were
also performed which improve the power supply dynamics and reduce noise. These changes improve
transparency and dynamic linearity, resulting in a smoother and more detailed top-end, tighter bass, more
explosive dynamic contrasts, and virtually holographic imaging. Left intact are the P-series unequalled
flexibility, high efficiency and superb reliability. These, along with multichannel design, are fundamental in
the a/d/s/ approach to systems engineering, which makes achieving true high fidelity reproduction simple
and predictable in any installation.

1

about this manual
To get the most from your a/d/s/ PowerPlate™, we recommend that you have the installation performed
by your qualified authorized a/d/s/ dealer. If this unit is installed by your dealer, we will extend the warranty
to two years instead of the standard one-year. However, if you feel that you have the necessary skills and
prefer to perform the installation yourself, this manual will guide you through the process of installation
and set-up. Please read through it completely before beginning the installation so that you may familiarize
yourself with the total procedure before you begin. If there is anything that you do not fully understand,
please consult with your a/d/s/ dealer before attempting the installation.

keep listening, but be safe!
Sustained listening to loud music over 100dB has been shown to cause permanent hearing damage.
Systems using a/d/s/ components are capable of achieving volume levels, which substantially exceed this
level. When operating your system for sustained periods at high volume, be sure to use hearing protection
to prevent long-term exposure. We want you to be able to enjoy the music for many more years.

features of your PowerPlate™
Transient Perfect™ MOSFET Power Supply - The heart of the P-series, this supply frees the
PowerPlate™ from the constraints of common pwm (pulse width modulated) supplies. The advantages
are: extremely fast overload recovery time, low output impedance for superior damping, and stability
during voltage fluctuations for reliable performance in the harsh automotive environment.
Remote Subwoofer or Constant Bass Level Control Capability - Can be used with accessory control
AC502 to provide a dashboard mounted rear channel subwoofer or Constant Bass level control.
Digital Crossover Frequency Display - The crossover frequency for each channel pair is displayed on
the top of the amplifier for quicker, more precise system tuning.
Detachable Plug in Connectors - High current speaker and power connectors simplifies installation.
Multi-cross™ Variable Built-in Crossovers - High-pass, Low-pass and Bandpass functions are built-in,
virtually eliminating the need for external crossover networks in even the most elaborate systems.
Constant Bass circuit - Signal from all input channels is summed, low-pass filtered and then made
available to all channels.
PowerPlate™ Design - a/d/s/ original low profile, high efficiency heatsink design keeps size minimum
and allows mounting where space is limited.
Wide Input Sensitivity Range - Allows connection to virtually any source unit from factory OEM radios
through low output preamps.
Simultaneous Stereo and Mono - Each channel pair may be used Stereo, Mono, Bridged or both Stereo
and Mono simultaneously. This allows an additional Mono speaker to be used with a stereo pair for
center-channel or subwoofer applications from each channel pair.
Same Side Adjustments - The P-series PowerPlate™ makes system adjustment easy by organizing all
signal-processing controls on one side of the amplifier. This layout allows convenient system adjustment
and facilitates a variety of installation possibilities when access to the controls is desired.

2

warnings and tips
Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable
only after the installation is complete and the wiring has been checked to make sure that there are no
problems. If your radio features a code type security system, be sure you know the code before
disconnecting the battery!
Your a/d/s/ PowerPlate™ should be installed in 12V negative ground vehicles only. Connection to other
types of electrical systems may cause damage to the vehicle or the amplifier. Wear Eye and Ear protection
when using power tools.
Before cutting or drilling carefully inspect the area to make sure there are no electrical wiring, fuel lines
or brake lines that could be damaged. Sometimes these components may be hidden between doublewalled panels, so be very careful.
Do not bypass or modify the fuses, or replace with one of a higher rating. The fuse should not fail under
normal operation. Repeated blowing indicates a problem with the amplifier or improper installation. An
additional power supply line fuse (not supplied) must be installed on the 12V supply line and located as
close as possible to the battery in order to protect the wire in the event of a short circuit.
Make sure the system is turned off when making or breaking any connections. Do not use your PowerPlate™
with speakers which have either terminal connected to the speaker frame or to the vehicle chassis.

mounting locations
Due to its low profile, there are many possible choices of mounting locations. Always mount the
PowerPlate™ in a place that protects it from the elements. In addition, mount the PowerPlate™ on a
stable, flat mounting surface. Whenever possible, pre-drill the mounting holes. Remember to check
behind the panel for hidden dangers in the form of hoses, fuel or brake lines or electrical wiring. Use a
marking pen or awl to mark the hole locations and pre-drill using a 1/8" bit.

Passenger compartment mounting
All PowerPlates™ have been designed with a low profile to make under
seat mounting possible. Regardless of where you choose to mount your
PowerPlate™ be sure to keep a minimum of 1" of clearance around the
amplifier for adequate airflow to prevent overheating.

Trunk compartment mounting
The most common mounting location is in the trunk or cargo
compartment. For optimum cooling, mount the PowerPlate™ chassis
vertically with the fins running vertically, or mount the PowerPlate™
horizontally with the fins pointing upward. Avoid horizontal mounting
locations with the fins pointing downward.
Also, locate the PowerPlate™ where it, and connections to it, will not be
damaged by cargo or tools, which may shift during vehicle operation.

Engine compartment mounting
Don’t even think about it! The PowerPlate™ was not designed to endure
the harsh chemical and heat environment of the engine compartment.
Failure to obey this warning will void your warranty.

3

system planning
Proper system planning is the best way to maximize your PowerPlate’s™ performance. By planning your
installation carefully you can avoid situations where the performance or the reliability of your system is
compromised. Your authorized a/d/s/ dealer has been trained to maximize your system’s sonic potential.
Your a/d/s/ dealer is a valuable resource in helping you with your system design and installation.

speaker requirements
Each channel of your PowerPlate™ can
easily drive 2 speaker loads when used in
the stereo mode. When a channel-pair is
bridged, the recommended minimum load
impedance is 4 for subwoofer use, and 4
for full range operation. Although operation
with lower impedances is not likely to cause
immediate damage to the internal circuitry,
the unit will most likely overheat, causing the
thermal protection circuitry to shut down the
amplifier. When the chassis cools down,
normal operation will resume. Continuing to
operate the amplifier under these conditions
is not recommended and will reduce its life
expectancy.
Most speakers designed for car audio
operation are 4 impedance. Connecting
two such speakers in parallel will result in a
2 impedance load as seen by the amplifier.
Some a/d/s/ subwoofer models feature a
dual 4 voice coil design. Connecting these
voice coils in parallel will result in a 2
nominal impedance, which is not
recommended for use with bridged channels
of your PowerPlate™.

4

system configurations
All a/d/s/ PowerPlates™ provide extensive features, which make a variety of system configurations
possible. It is not feasible to cover all of the possibilities within the few pages of this manual. There are a
few system configurations, however, which are extremely popular when used alone or as a "building
block" of a larger more elaborate system. Please review systems 1 through 6 described below for
suggestions on how to configure the most popular combinations. Larger systems may be built from a
combination of the simpler building blocks as shown in systems 7.

button is disengaged

control is non-operational

button is engaged

control is operational

System 1 - PH30.2 used in 6-channel mode. Channels 1 and 2 are used for front high-pass speakers,
channels 3 and 4 are used for rear high-pass speakers and channels 5 and 6 are used to drive a stereo
pair of subwoofers. Although shown as a 4-channel input, the source unit can be either 2 or 4 channel
depending on the setting of the 2/4 channel switch.
Note: Optional AC502 can be used in this system to adjust the level of the subwoofers.

70A

subwoofer

subwoofer

rear right
satellite

front left
satellite
front right
satellite
rear left
satellite

5

System 2 - PH30.2 used in 5-channel mode with the AC502 providing level control for bridged channels
5 and 6. 1 and 2 are high-passed for front speaker and channels 3 and 4 are high-passed for rear
speakers. Although shown as a 4-channel input, the source unit can be either 2 or 4-channel depending
on the setting of the 2/4 channel switch.

70A

front left
satellite
front right
satellite
rear left
satellite
subwoofer
rear right
satellite

System 3 - PH30.2 used in 6-channel mode with source unit providing direct level control for channels 5
and 6 through the fade control. Channels 1 and 2 are configured high-pass for tweeters, channels 3 and
4 are configured bandpass for midrange and channels 5 and 6 are configured low-pass for subwoofers.

70A

left tweeter
subwoofer
right tweeter

left midrange

right midrange

subwoofer

6

System 4 - PH30.2 used in 4-channel mode with high-pass tweeters and bandpass midrange. Channels
1and 2 are configured high-pass for the main tweeters and channels 3 and 4, and 5 and 6 are configured
bandpass for main midrange. Channels 4 and 6 are controlled by the 3/4 level control and crossover
section. The amplifier is configured for a 2-channel input.

70A

left tweeter

right tweeter

left midrange

right midrange

System 5 - PH30.2 used in 4-channel mode with high-pass main speakers and low-pass
subwoofers.Channels 1 and 2 are configured high-pass for front speakers and channels 3/4, and 5/6 are
configured low-pass for bridged output subwoofers. The amplifier is configured for a 4-channel input.
Front/rear fade adjusts subwoofer level.

70A

left satellite

right satellite

subwoofer

subwoofer

7

System 6 - PH30.2 used in 3-channel bridged mode with two channels dedicated for the main speakers
and one bridged channel pair used for a subwoofer. Channels 1/2, and 3/4 are configured high-pass for
the main front speakers using a single pair of RCA inputs to produce a bridged mono output.

70A

subwoofer

right
satellite

left
satellite

8

System 7 - Two PH30.2’s are used. The first PH30.2 is configured the same as system 4 and the second
PH30.2 is configured similar to system 5. The first amplifier drives the front midrange and tweeters and
the second amplifier drives the rear speakers and the subwoofer.

front right
tweeter

front left
midrange

front left
tweeter

front right
midrange

70A

front

rear

70A

rear left
satellite

subwoofer

rear right
satellite
subwoofer

9

10

11

2ch/4ch input switch- Leave this switch OUT if you are using 4 channels of input. Push the switch IN if you have only 2 channels of input to
send input 1 and 2 to channels 3 and 4, respectively. (see page 15)

5/6 source- This switch selects the source for channel 5 and 6. Select the input source as input RCA 1 and 2, the summed signals from RCA inputs 1and
3 and 2 and 4, or as RCA inputs 5 and 6.

level controls- Use these controls to match the input level from the source unit to each pair of amplifier channels. (see page 15)

crossover 1/2 switch- this switch will turn the channel 1/2 crossover on or off, or send channel 3 and 4 signal to channels 1 and 2, respectively.
(see page16)

crossover 1/2 frequency- This control sets the highpass crossover point for channels 1 and 2. (see page 16)

crossover 3/4 highpass switch- Push this switch IN to activate the channel 3/4 highpass crossover, or OUT to bypass the crossover.
(see page 16)

crossover 3/4 highpass frequency- This control sets the highpass crossover point for channels 3 and 4. (see page 16)

crossover 3/4 lowpass switch- Push this switch IN to activate the channel 3/4 lowpass crossover, or OUT to bypass the crossover.
(see page 16)

crossover 3/4 lowpass frequency- This control sets the lowpass crossover point for channels 3 and 4. (see page 16)

crossover 5/6 switch - This switch will turn the channel 5/6 crossover on or off, or send channel 3and 4 signal to channels 5and 6, respectively (see page 16)

crossover 5/6 frequency this control sets the lowpass crossover point for channels 5 and 6 (see page 16)

output switches- These switches determine whether the output is mono, bridged or stereo configuration for channels 1/2 and 3/4.
(see page 15)

Constant Bass level- Use these controls to mix summed mono sub-bass information into channels 1/2 and 3/4. (see page 17)

Constant Bass frequency- This control sets the lowpass crossover point of the Constant Bass signal. (see page 17)

AC502 control- When using an optional AC502 remote level control, the AC502 will control the constant bass level when the switch is IN, or channel3/4
level when the switch is OUT. (see page 17)

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

amplifier and crossover controls

installation
1.

Disconnect the battery ground cable. Reconnect the ground cable only after the installation is
complete and the wiring has been checked to make sure that there are no problems. If your
radio features a code type security system, be sure you know the code before disconnecting
the battery!

2.

Run a minimum AWG #8 power wire directly from the battery to the PowerPlate™ mounting
location. Install a fuseholder at the battery end of this cable either within 18" of the battery
or before the wire runs through any metal partitions. Do not install the fuse at this time.

3.

Attach a minimum AWG #8 ground wire to a solid chassis ground point near the mounting
location. Keep this wire as short as possible. Scrape all paint and primer off of the sheet
metal at the ground point to ensure a good electrical connection. Attach the wire to the
ground point with a nut, bolt and star washer.

4.

Run the signal leads and remote turn-on leads from the head unit to the PowerPlate™
location. If using an internally powered radio or factory radio refer to the "signal sources"
section for the proper wiring connections.

5.

Install the speakers and run each of the speaker leads to the PowerPlate™ location. Connect
the speaker, remote, and power wires to the appropriate terminals on the plug-in terminal
blocks. Refer to the "controls and connections" or "system planning" sections for
information on the proper connections. The speaker terminal blocks install with the set
screws facing up and power terminal block installs with the set screws facing down.

6.

Preset the 2/4 channel selector switch, crossover and channel mode switches, and crossover
frequency switches to the desired positions. Refer to the "controls and connections" section
for more information.

7.

Adjust all amplifier input level controls to the 1/4 position.

8.

Mount the amplifier into position and plug in the power and speaker terminals. Attach the
input signal cables.

9.

Reattach the battery ground cable.

10.

Double check your switch and control settings. Install a 70 amp fuse in the fuseholder you
have installed near the battery.

11.

Turn on the signal source at a low volume level. Using the balance and fader controls, check to
see that each channel is connected to the proper speakers. Make sure that the proper
frequency range is being sent to each speaker if you are using the crossover features built
into your PowerPlate™.

12.

Adjust the input sensitivity and crossover frequencies as described in the "tuning" section.

13.

Read the rest of this manual to get maximum enjoyment from your system.

controls and connections
power connections
•
Use AWG #8 or larger power and ground cable.
•
Install 70 amp fuse in the power wire within 18" of the battery.
•
Keep the ground wire to a minimum length and attach solidly to a clean metal part of the
vehicle. The addition of a .5 Farad to 1 Farad power supply capacitor, mounted as close as
possible to the PowerPlate™, may improve performance in some systems.

12

70A

Connect to 12V turn-on
lead from source unit

fuse

Connect to chassis of vehicle

Connect to
chassis of vehicle
70 Amp fuse
less than
18" from
battery

Factory chassis ground

speaker connections for stereo configurations
Minimum recommended impedance is 2 stereo. Speaker terminals accept up to AWG #12 speaker wire.

70A

speaker connections for bridged configurations
Minimum recommended impedance is 4 when bridged to subwoofers and 4 when bridged to full range
speakers. Speaker terminals accept up to AWG #12 speaker wire.

70A

13

signal sources
Due to the wide input level adjustment range, all a/d/s/ PowerPlates™ can be driven with either a
conventional preamplifier drive signal or the amplifier signal from a powered source unit. This makes the
PowerPlate™ perfect for upgrading an OEM (Original Equipment Manufacturer) stereo system while
retaining the factory installed radio.
Because of the high impedance of the a/d/s/ input stage, the factory radio drives an easy load. This ensures
lower distortion levels than if it was driving speakers or a Line Output Converter accessory. As a result, a
high quality factory installed radio can deliver high quality sound that is nearly as good as the sound from
a high-end aftermarket source unit. The speaker outputs of the factory radio are simply connected to a
mini-DIN adapter as shown below. From this point on, the signal can be treated exactly as you would a
preamp-level signal, except that the input level controls on the PowerPlate™ will be set to a lower than
usual level when you make your final adjustments.
Conventional aftermarket sources may be connected using standard shielded RCA cables from the source
unit’s preamp outputs to the PowerPlate™ inputs.
Note: When using 4 channels of input, be sure to configure the 2ch/4 ch input switch to 4ch
input. Failure to do so may result in damage to the source unit.

70A

Pin

Wire Color

Connects to Head Unit

1
2
3
4
5
6
7
8

gray
violet/black
white
gray/black
white/black
green
green/black
violet

front right +
rear right front left +
front right front left rear left +
rear left rear right +

14

internal signal routing
2-channel/4-channel input switch - routes RCA input from channels 1/2 to channels 3/4.

When the switch is engaged, channel 1 input is
routed to both amplifier channels 1 and 3 with input
channel 2 routed to amplifier channels 2 and 4.
Switch in the engaged position.

When the switch is disengaged, channels 1, 2, 3,
and 4 receive signal individually from their
respective inputs.
Switch in the disengaged position.

Level controls - Independent level controls for channels 1/2, 3/4 and 5/6 adjust
the input sensitivity from 100 mV to 8 VRMS.

Output - Three position switches determine the output configuration. Each stereo pair of channels can
be configured in either stereo, summed-bridged and bridged-mono.

When the switch is in the left position, the output channels are configured for
stereo operation.

When the switch is in the center position, the output channels are configured
for summed bridged operation by mixing the left and right input signals
together.

When the switch is in the right position, the output channels are configured
for a bridged mono output using a single RCA input. Ch 1 input is used for
channels 1 & 2, ch 4 input is used for channels 3 & 4 and Ch 5 is used for
channels 5 & 6.

15

multi-cross™ crossover configuration
xover control 1/2- The crossover selection for channels 1 & 2 has three options:

When the switch is in the left position, the crossover section of the amplifier is
bypassed. Channels 1 & 2 output is full range.

When the switch is in the center position, channels 1 & 2 are filtered through a 12dB
per octave high-pass crossover that is infinitely variable from 45Hz to 5,000Hz.

When the switch is in the right position, channels 1 & 2 receive signal from the
crossover output of channels 3 & 4.
Note: When crossover 3/4 output is selected for channels 1/2, the 3/4 level
control adjusts the output level for channels 1/2 and 3/4 simultaneously.

xover control 3/4- The crossover sections dedicated for channels 3 & 4 are activated by depressing the
switch next to each frequency adjustment control. Both high-pass and low-pass crossovers are infinitely
adjustable from 45Hz to 5,000Hz. The high-pass and low-pass sections may be used individually or
together to create a bandpass filter.
Note: When using both sections to create a bandpass filter, make
sure you have selected a low-pass frequency that is higher than the
high-pass frequency!
xover control 5/6- The crossover selection for channels 5 & 6 has three options:

When the switch is in the left position, the crossover section of the amplifier is bypassed.
Channels 5 & 6 output is full range.

When the switch is in the center position, channels 5 & 6 are filtered through a 12dB
per octave low-pass crossover that is infinitely variable from 45Hz to 5,000Hz.

When the switch is in the right position, channels 5 & 6 receive signal from the crossover
output of channels 3 & 4.
Note: When crossover 3/4 output is selected for channels 5/6, the 3/4 level
control adjusts the output level for channels 3/4 and 5/6 simultaneously.

digital crossover frequency display
To facilitate quicker system tuning, we have incorporated
a digital display that shows the crossover frequency for
each crossover section, including the lowpass crossover
for the constant bass circuit. Push the select switch to
scroll through the different sections, and a blue led will
indicate which crossover is currently displayed.

ch 1/2 high pass
ch 3/4 high pass
ch 3/4 low pass
ch 5/6 low pass

select

constant bass

16

Constant Bass circuit
To mix sub-bass information into channels 1/2 and 3/4, select a lowpass crossover point, and use the level controls to set the level of subbass signal sent to channels 1/2 and 3/4.

using the AC502 (optional)
The AC502 remote level control, available as an accessory from your a/d/s/ dealer, may be used with your
PowerPlate™ to remotely adjust the level of channels 5/6, OR to remotely adjust the constant bass level.
To use this feature, simply connect the AC502 into the DIN connector on the PH30.2, and install the
AC502 in the desired location. To adjust the constant bass level, Locate the AC502 control switch on
amplifier and push IN, or leave it OUT to control the level of channels 5/6. This remote capability can also
be used on channels 1/2 and 3/4 when the PH30.2 is used in the 2-channel bridged mode. Refer to the
"adjustments" section for information on setting up the AC502.

70A

tuning
tuning the crossover
All of the crossover controls in the multi-cross™ crossover section are marked at four
reference frequency points. These are 45Hz, 175Hz, 600Hz and 5,000Hz. Specific crossover
points should be chosen based on the operating range recommended by the manufacturer
of your speakers. The 85Hz position is a good starting point to use for subwoofer low-pass
or midrange high-pass use. When bi-amping a/d/s/ loudspeaker components 2500Hz is a
good starting point for the midrange low-pass, and 3500Hz is recommended as the tweeter high-pass.
Once installed, you can fine tune the crossover points using your ears or with the aid of an RTA to achieve
maximum performance. With any loudspeaker, minor deviations from the recommended frequency
ranges may provide superior results, depending on your speaker locations and your vehicle’s acoustics.
Setting crossover frequencies higher than recommended will not cause damage and may provide good
results. However, DO NOT set high-pass tweeter crossover points below the tweeters recommended
operating range. Doing so will likely cause damage not covered by the manufacturer’s warranty. If you are
using non-a/d/s/ speakers, refer to the manufacturer’s recommendation for selecting the proper crossover
frequencies.

17

adjusting input sensitivity
The input sensitivity setting is important to ensure proper performance, low noise levels, and maximum
system reliability. As a general rule, components at the "front end" of the system should be set as high
as possible with the input sensitivity of the amplifier set as low as possible while still providing adequate
volume levels. Using a high signal level from the source and a low input sensitivity setting on the amplifier
will keep the background noise levels of the system low.
The following procedure will help you get the widest dynamic range from your system:
1.

Start with the input level controls of your PowerPlate™ at the minimum (counterclockwise)
position.

2.

Set the tone controls and any controls on any equalizers or other signal processors to their flat
or bypassed positions.

3.

Set the input and output level controls, if any, on any associated equipment such as equalizers
or outboard electronic crossover as recommended by their manufacturers.

4.

Select a well recorded CD or Tape containing material recorded at a fairly high level. Musical
content is not important except that the music chosen should be recorded such that any system
distortion can be clearly heard, not masked by musical content.

5.

Increase the source unit volume control about halfway. Increase the PowerPlate™ level control
associated with the front full range (or midrange in a bi-amplified front system) until you can
hear sound at a low but clear level.

6.

While listening carefully for any signs of distortion, slowly increase the source unit volume
control until you either hear the first signs of distortion or you can’t turn it up any more. Back
down on the volume control slightly until the distortion goes away. You have just found the
maximum undistorted output level of your source unit. Do not exceed the level in normal
operation, as doing so will just send a distorted signal to the rest of the system.

7.

Returning to the PowerPlate™ level control associated with the front main speakers, slowly
increase it until you reach the point where distortion just begins to appear. This will be at the
point where either the amplifier reaches its maximum output level, or the speakers reach their
output limits. Either way, you have just calibrated the system so that the maximum system
output occurs at the same point as the maximum output from the source. This will give you
minimum system noise yet the system will reach its maximum output capability.

8.

Reduce the source unit volume to a comfortable listening level. With the balance and fader
controls still centered, adjust the remaining level controls for the proper system balance. If you
are adjusting a system with multiple amplifiers, it is easiest to adjust the controls in the
following order: 1. Front speakers 2. Rear speakers 3. Subwoofers

9.

If using an AC502 remote level control, adjust the subwoofer level with the AC502 in the mid
position. This will give you the ability to boost the subwoofer level approximately 6dB when
the AC502 is turned fully clockwise.

10.

Double check your system levels by increasing the source unit volume control to the previously
determined maximum position. If you hear distortion from any of the channels, reduce the
PowerPlate™ input level for those channels until the distortion goes away.

Adjusting the input levels in this way will get maximum undistorted output from your system and will
make it unlikely that you will cause damage to any of the components of your system by overpowering
them.

18

troubleshooting
symptom

possible cause

action to take

no output

low or no remote turn-on
input

check remote turn-on voltage
output at amplifier and correct
as needed

fuse blown

check power wire integrity
and reversed polarity, repair
as needed and replace fuse

power wires not connected

check power wire and ground
connections and repair or
replace as needed

audio input not connected
or no output from source

check input connections and
signal integrity, repair or
replace as needed

speaker wires not connected

check speaker wires and repair
or replace as needed

speakers are blown

check system with known
working speaker and repair or
replace speakers as needed

thermal protection engages
when amplifier heatsink
temperature exceeds 90° C

make sure there is proper
ventilation for amplifier and
improve ventilation as needed

loose or poor audio input

check input connections and
repair or replace as needed

amplifier level sensitivity set too
high; exceeding maximum
output capability of amplifier

reset gain referring to the
tuning section of the manual
for detailed instructions

impedance load to amplifier too
low

check speaker impedance load
if below 2 stereo or 4
mono rewire speakers to
achieve a higher impedance

shorted speaker wires

check speaker wire
connections and repair or
replace as needed

speaker not connected to
amplifier properly

check speaker wiring and
repair or replace as needed
refer to the installation section
of this manual for detailed
instructions

internal crossover not set
properly for speaker

reset crossovers referring to the
multi-cross™ crossover
configuration section of this
manual

audio cycles on and off

distorted output

19

symptom

possible cause

action to take

distorted output (cont’d)

speakers are blown

check system with known
working speakers and repair or
replace as needed

poor bass response

speakers wired with wrong
polarity causing cancellation
at low frequencies

check speaker polarity and
repair as needed

crossover set incorrectly

reset crossovers referring to
the multi-cross™ crossover
configuration section of this
manual for detailed instructions

impedance load to amplifier
too low

check speaker impedance load,
if below 2 stereo or 4 mono
rewire speakers to achieve a
higher impedance

short in power wire or incorrect
power connections

check power and ground
connections and repair as
needed

fuse used is smaller than
recommended

replace with proper fuse size

too much current being drawn

check speaker impedance load,
if below 2 stereo or 4 mono
rewire speakers to achieve a
higher impedance

short in power wire or incorrect

check power and ground
connections and repair as
needed

too much current being drawn

check speaker impedance load,
if below 2 stereo or 4 mono
rewire speakers to achieve a
higher impedance and replace
with recommended fuse size

battery fuse blowing

amplifier fuse blowing

check power and ground
connections and repair as
needed
fuse used is smaller than
recommended

replace with proper fuse size

20

specifications
amplifier section

PH 30.2

power output 4 (watts)1

6 channel 6 x 75
3 channel 3 x 250

power output 2 (watts)2
fuse type
dimensions
distortion all channels driven

6 x 112.5
70 A maxi
13" x 19 7/8" x 2"
<0.1% 20Hz to 20,000Hz

frequency response

±1dB 10Hz to 30,000Hz

signal-to-noise ratio full
bandwidth @ rated output power

>90dB

damping factor @ output
connector full bandwidth

>150

input sensitivity

100mV to 8Vrms for full output

input impedance

47 k

crossover section
ch 1 & 2

high-pass 12dB/octave variable 45Hz- 5kHz

h3&4

high-pass & low-pass 12 dB octave variable 45Hz- 5kHz

ch 5 & 6

low-pass 12 dB / octave variable 45Hz- 5kHz

Constant Bass

low-pass 12dB/octave variable 30Hz- 300Hz

1 All channels driven, continuous FTC rated 4 load, 20Hz to 20,000Hz, <0.1% THD, power input
voltage at 13.8DVC.
2 All channels driven, continuous FTC rated 2 load, 20Hz to 20,000Hz, <0.1% THD, power input
voltage at 13.8DVC.
3 All channels are selectable with infinitely variable adjustments from 45Hz to 5,000Hz with a slope
of 12dB/octave and a "Q" of .707.

21

warranty information
LIMITED TWO YEAR CONSUMER WARRANTY

Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be
defective in workmanship or material under normal use, for a period of two years from the date of
purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was
installed by an authorized Directed dealer. During this two year period, there will be no charge for this
replacement PROVIDED the unit is returned to Directed, shipping pre-paid. If the unit is installed by
anyone other than an authorized Directed dealer, the warranty period will be 1 year from date of purchase
by the dealer as indicated by the date code marking of the product. During this 1 year period, there will
be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. This
warranty is non-transferable and does not apply to any unit that has been modified or used in a manner
contrary to its intended purpose, and does not cover damage to the unit caused by installation or removal
of the unit. This warranty is void if the product has been damaged by accident or unreasonable use,
neglect, improper service or other causes not arising out of defects in materials or construction. ALL
WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF
NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE
MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES
INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. Unit must be returned to Directed, postage
pre-paid, with: consumer's name, telephone number, and address, authorized dealer's name and address,
and product description. IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE
SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER. ALL UNITS
RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER
INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY. Note:
This warranty does not cover labor costs for the removal and reinstallation of the unit.
BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES
BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH
CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

22

front_cover.qxd

10/26/56

5:13 AM

Page 1

Directed Electronics, Inc. All rights reserved G49200 09-02

a



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2002:10:24 19:05:32Z
Modify Date                     : 2002:10:28 10:38:10-08:00
Page Count                      : 24
Creation Date                   : 2002:10:24 19:05:32Z
Mod Date                        : 2002:10:28 10:38:10-08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Summer
Metadata Date                   : 2002:10:28 10:38:10-08:00
Creator                         : Summer
Title                           : ph30.2.qxd
Has XFA                         : No
EXIF Metadata provided by EXIF.tools

Navigation menu