65HM167 50HM67 OM E

User Manual: 65HM167

Open the PDF directly: View PDF .
Page Count: 74

HM67 (E/F) Web 213:276

HIGH-DEFINITION TELEVISION

50HM67

57HM167

65HM167

YC/N

VX1A00039100

Integrated High Definition

DLP

Projection Television

Owner’s Record

The model number and serial number are on the back of

your TV. Record these numbers in the spaces below.

Refer to these numbers whenever you communicate

with your Toshiba dealer about this TV.

Model number:

Serial number:

For an overview of steps for setting up your new TV, see page 10.

Note: If the TV is powered off and then quickly on again when the

lamp unit is hot, it may take several minutes for the picture to appear

on-screen. This is a property of DLP

TV lamp technology and is NOT

a sign of malfunction. For details, see "IMPORTANT NOTICE ABOUT

HOT LAMP RESTART" on page 6.

Note: To display a High Definition picture, the TV must be receiving a

High Definition signal (such as an over-the-air High Definition TV

broadcast, a High Definition digital cable program, or a High Definition

digital satellite program). For details, please contact your TV antenna

installer, cable provider, or satellite provider.

50HM67_EN.book Page 1 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will

help you use the many exciting features of your new TV. Before

operating the TV, please read this manual completely, and

keep it nearby for future reference.

NOTE TO CATV INSTALLERS IN THE U.S.A.

This is a reminder to call the CATV system installer’s attention

to Article 820-40 of the U.S. NEC, which provides guidelines for

proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the building,

as close to the point of cable entry as practical. For additional

antenna grounding information, see items 28 and 29 on page 4.

Child Safety

It Makes A Difference

Where Your TV Stands

Congratulations on your purchase!

As you enjoy your new TV, keep these safety tips in mind:

The Issue

aIf you are like most consumers, you have a TV in your home.

Many homes, in fact, have more than one TV.

The home theater entertainment experience is a growing trend,

and larger TVs are popular purchases; however, they are not

always supported on the proper TV stands.

aSometimes TVs are improperly secured or

inappropriately situated on dressers, bookcases,

shelves, desks, audio speakers, chests, or carts.

As a result, TVs may fall over, causing

unnecessary injury.

Toshiba Cares!

aThe consumer electronics industry

is committed to making home

entertainment enjoyable and safe.

The Consumer Electronics Association

formed the Home Entertainment Support

Safety Committee, comprised of TV and

consumer electronics furniture manufacturers, to

advocate children’s safety and educate consumers

and their families about television safety.

Tune Into Safety

aOne size does NOT fit all! Use appropriate furniture large

enough to support the weight of your TV (and other electronic

components).

Use appropriate angle braces, straps, and anchors to secure your

furniture to the wall (but never screw anything directly into the TV).

aCarefully read and understand the other enclosed

instructions for proper use of this product.

aDo not allow children to climb on or play with furniture and TVs.

aAvoid placing any item on top of your TV (such as a VCR, remote

control, or toy) that a curious child may reach for.

aRemember that children can become excited while watching

a program and can potentially push or pull a TV over.

aShare our safety message about this hidden hazard of the home

with your family and friends. Thank you!

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Lamp Unit Replacement

The lamp in this product has a limited service life. The length

of service life varies depending on product use and user

settings. If you use the lamp beyond its service life:

• you may notice a reduction in the colors and/or brightness

of the picture, at which time you should replace the lamp

unit; and

• the strength of the quartz glass in the lamp will be reduced

and the lamp may rupture. If the lamp ruptures, the TV will

not operate until the lamp unit is replaced.

Dispose of the used lamp unit by the approved method for

your area.

See “Lamp unit replacement and care”

in Chapter 9.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

(This does not apply to “Lamp

unit replacement and care” in Chapter 9.)

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN.

Note: The lamp unit contains mercury.

Disposal of mercury may be regulated due to

environmental considerations. For disposal or recycling

information, contact your local authorities or the Electronic

Industries Alliance (www.eiae.org).

CAUTION: This television is for use only with

the Toshiba stand indicated below. Use with other

carts or stands is capable of resulting in

instability, causing possible injury.

Television Stand Model

50HM67 ST 5067

57HM167 ST 57167

65HM167 ST 65167

2500 Wilson Blvd.

Arlington, VA 22201 U.S.A.

www.CE.org

CEA is the Sponsor, Producer and

Manager of the International CES

50HM67_EN.book Page 2 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of

the polarized or grounding type

plug. A polarized plug has two blades

with one wider than the other.

A grounding type plug has two blades

and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked

on or pinched, particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been

dropped.

Additional Safety Precautions

14a) Item 14 does not apply to “Lamp unit replacement and

care” in Chapter 9.

14b) CAUTION: If the TV is dropped and the cabinet or

enclosure surface has been damaged or the TV does

not operate normally, take the following precautions:

• ALWAYS turn off the TV and unplug the power cord to

avoid possible electric shock or fire.

• To prevent personal injury, never handle the damaged

television.

• ALWAYS contact a service technician to inspect the TV

any time it has been damaged or dropped.

15) CAUTION:

• To reduce the risk of electric shock, do not use the

polarized plug with an extension cord, receptacle, or

other outlet unless the blades can be inserted

completely to prevent blade exposure.

• To prevent electric shock, match wide blade of plug to

wide slot; fully insert.

16) WARNING: This product contains a lamp to project

the picture, and requires special safety precautions:

• See Chapter 9 for instructions on lamp unit replacement

and care.

•DO NOT attempt to service this product except as

specified in the “Lamp unit replacement and care”

section in Chapter 9. The only user-serviceable item in

this product is the lamp unit.

17) WARNING:

To prevent the spread of fire, keep candles or other open

flames away from this product at all times.

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all

warnings when installing your TV:

18) Never modify this equipment. Changes or modifications

may void: a) the warranty, and b) the user’s authority to

operate this equipment under the rules of the Federal

Communications Commission.

19) DANGER: RISK OF

SERIOUS PERSONAL

INJURY, DEATH, OR

EQUIPMENT DAMAGE!

Never place the TV on an unstable cart,

stand, or table. The TV may fall, causing

serious personal injury, death, or serious

damage to the TV.

20) Never place or store the TV in direct sunlight; areas

subject to excessive dust or vibration; or locations with

temperatures at or below 41°F (5°C). See “Specifications”

section on page 66 on operating conditions.

21) Always place the TV on the TV stand provided with the TV

or on a sturdy, level, stable surface that can safely support

the size and weight of the unit. See “Notice of possible TV

stand instability” and “Child Safety” on page 2.

22) The apparatus shall not be exposed to dripping or

splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

23) Always place the back of the television at least one (1)

inch away from any vertical surface (such as a wall) to

allow proper ventilation.

Wide blade

(continued)

50HM67_EN.book Page 3 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

24) Never block or cover the slots or openings in the TV

cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar surface;

• too close to drapes, curtains, or walls; or

• in a confined space such as a bookcase, built-in

cabinet, or any other place with poor ventilation.

The slots and openings are provided to protect the TV

from overheating and to help maintain reliable operation of

the TV.

25) Never allow anything to rest on or roll over the power cord,

and never place the TV where the power cord is subject to

wear or abuse.

26) Never overload wall outlets and extension cords.

27) Always operate this equipment from a 120 VAC, 60 Hz

power source only.

28) Always make sure the antenna system is properly

grounded to provide adequate protection against voltage

surges and built-up static charges (see Section 810 of the

National Electric Code).

29)

• Use extreme care to make sure you are never in a

position where your body (or any item you are in contact

with, such as a ladder or screwdriver) can accidentally

touch overhead power lines. Never locate the antenna

near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during

lightning activity: a) an antenna system; or b) cables,

wires, or any home theater component connected to an

antenna or phone system.

Care

For better performance and safer operation of your TOSHIBA

TV, follow these recommendations and precautions:

30) Always sit approximately 10–25 feet away from the TV and

as directly in front of it as possible. The picture can appear

dull if you sit too far to the left or right of the TV, or if

sunlight or room lights reflect on the screen. Turn the TV

off to check for reflections on the screen, and then remove

the source of reflections while viewing the TV.

31) Always unplug the TV before cleaning. Never use liquid or

aerosol cleaners. Clean only with a soft, dry cloth. Do not

spray volatile compounds, such as insecticide, on the

cabinet. This may discolor or damage the cabinet.

32)

Never spill liquids or push objects of any kind into the TV

cabinet slots.

33) If the air temperature rises suddenly (for example, when

the TV is first delivered), condensation may form on the

lenses. This can make the picture appear distorted or the

color appear faded. If this happens, turn off the TV for 6 to

7 hours to allow the condensation to evaporate.

34) For added protection of your TV from lightning and power

surges, always unplug the power cord and disconnect the

antenna from the TV if you leave the TV unattended or

unused for long periods of time.

35) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the

unit is being turned on or off. If these sounds become

frequent or continuous, unplug the power cord and contact

a Toshiba Authorized Service Center.

36) Special care for DLP® (Digital Light Processing) units:

• The lamp unit in this product has a limited service life.

The length of service life varies depending on product

use or user settings. If you use the lamp beyond its

service life:

• you may notice a reduction in the colors and/or

brightness of the picture, at which time you should

replace the lamp unit; and

• the strength of the quartz glass in the lamp will be

reduced and the lamp may rupture. If the lamp ruptures,

the TV will not operate until the lamp unit is replaced.

See “Lamp unit replacement and care” in Chapter 9.

• Dispose of the used lamp unit by the approved method

for your area.

• The lamp unit contains mercury. Disposal of

mercury may be regulated due to

environmental considerations. For disposal or

recycling information, please contact your

local authorities or the Electronic Industries

Alliance (www.eiae.org).

Service

37)

Never attempt to service the TV yourself, except as

specified in the “Lamp unit replacement and care” section

in Chapter 9. Opening and removing the covers may

expose you to dangerous voltage or other hazards. Failure

to follow this WARNING may result in death or serious

injury. Refer all servicing not specified in this manual to a

Toshiba Authorized Service Center.

38) If you have the TV serviced:

• Ask the service technician to use only replacement

parts specified by the manufacturer.

• Upon completion of service, ask the service technician

to perform routine safety checks to determine that the

TV is in safe operating condition.

DLP® and the DLP logo are registered trademarks of Texas

Instruments.

Ground clamp

Antenna discharge unit

(NEC Section 810-20)

Grounding conductors

(NEC Section 810-21)

Power service grounding

electrode system (NEC Art 250 Part-H)

Ground clamps

Antenna lead-in wire

Electric service equipment

DANGER: RISK OF SERIOUS

PERSONAL INJURY OR DEATH!

WARNING:

RISK OF ELECTRIC SHOCK!

WARNING:

RISK OF ELECTRIC SHOCK!

50HM67_EN.book Page 4 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

39) When the TV reaches the end of its useful life, ask a

qualified service technician to properly dispose of the TV.

Note: The lamp unit contains mercury. Disposal of

mercury may be regulated due to environmental

considerations. Dispose of the used lamp unit by the

approved method for your area.

For disposal or recycling information, please contact your

local authorities or the Electronic Industries Alliance

(www.eiae.org).

FCC Declaration of Conformity

Compliance Statement

(Part 15):

The Toshiba 50HM67, 57HM167, and 65HM167 Televisions

comply with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that

may cause undesired operation.

The party responsible for compliance to these rules is:

Toshiba America Consumer Products, L.L.C.

82 Totowa Rd. Wayne, NJ 07470.

Ph: 1-800-631-3811

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15

of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

removing and applying power to the equipment, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Caution: Changes or modifications to this equipment not

expressly approved by Toshiba could void the user’s authority

to operate this equipment.

ENERGY STAR® qualified television. Products

that earn the ENERGY STAR prevent green

house gas emissions by meeting strict

energy efficiency guidelines set by the U.S.

Environmental Protection Agency and the U.S.

Department of Energy. ENERGY STAR and the

ENERGY STAR mark are registered U.S. marks.

50HM67_EN.book Page 5 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Important notes about your

DLP® projection TV

1) The light source for this TV is a projection lamp unit with a

limited service life. When the lamp wears out, the picture

may become dark or black or the lamp may fail, at which time

you must replace the lamp unit (- “Lamp unit replacement

and care” on pages 63–65).

2) When the lamp mode is set to Low Power, every time the

TV is powered on, the lamp will initially be in High Bright

mode but will switch to Low Power mode after a short

period of time. You may notice a change in screen brightness

when this happens. This is normal and is not a sign of

malfunction (-page 57 for details).

3) Every time the TV is powered on, it may take several minutes

for the picture to obtain full brightness (- “IMPORTANT

NOTICE ABOUT HOT LAMP RESTART,” at right).

4) The TV’s display is manufactured using an extremely high

level of precision technology; however, an occasional pixel

(dot of light) may show constantly on the screen. This is a

structural property of DLP® (Digital Light Processing®)

technology and is not a sign of malfunction. Such pixels are

not visible when the picture is viewed from a normal viewing

distance.

5) Always sit approximately 10–25 feet away from the TV and

as directly in front of it as possible. The picture quality may

be affected by your viewing position and length of viewing

time. If you sit too closely to the TV for too long, you may

suffer from eye fatigue. See item 30 under “Care” on page 4.

6) Depending on the media you are viewing, it is possible,

although unlikely, that a limited number of viewers may see

a “rainbow effect” on the screen, which can, in rare instances,

result in eye fatigue. This is a rare occurrence related to

DLP® technology and is not a sign of TV malfunction.

7) This TV contains several cooling fans to moderate

the internal temperature. You may be able to hear

the fans for several minutes after the TV is turned

off. This is a function of the Power-On Mode

feature and is not a sign of TV malfunction. You can set

the Power-On Mode feature to stop the fans as soon as the

TV is powered off. See “Setting the Power-On Mode

feature” (- page 35).

8) The yellow and blue LED lights at the bottom center of the

TV front indicate your TV’s current status. If either light

flashes, see “LED indications” (- page 62).

9) Every time the TV power cord is plugged in, the yellow LED

will blink until the TV enters standby mode (plugged in but

not powered on). This is normal and is not a sign of

malfunction.

Trademark Information

• WOW, SRS and l symbol are trademarks of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc.

• Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are registered trademarks of Dolby

Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

•DLP

® and the DLP logo are registered trademarks of Texas

Instruments.

“Voice announce” feature

When certain non-standard conditions occur, the LEDs

on the TV will blink and the TV will play a recorded

“voice announcement” describing the condition (see the

LED indication table on page 62 for the specific conditions

that include a voice announcement).

To repeat the voice announcement and hear additional

information, press the MENU button on the TV while the

LEDs are blinking.

IMPORTANT NOTICE ABOUT HOT LAMP RESTART

When the TV has been powered on long enough for the lamp

unit to get hot, it may take several minutes for the picture to

appear in the following situations:

• When the Power-On Mode feature is set to Power-

Saving and you turn the TV off and then on again

within a few minutes; or

• If the TV is on when a short-term power failure, power

surge, or other similar power failure occurs, such that

the TV loses and regains power within a few minutes.

This is a property of DLP® TV lamp technology and is

NOT a sign of malfunction.

If this occurs, the yellow LED on the TV front panel will blink

(and the blue LED will be lit solid) until the TV is finished

restarting the lamp and the normal picture appears. If both

LEDs are blinking, you will need to turn the TV off and then

on again to restart the lamp.

50HM67_EN.book Page 6 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Contents

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview of steps for installing, setting up, and using

your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

TV front and side panel controls and connections . . . . . . . . 11

TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 2: Connecting your TV . . . . . . . . . . . . . . . . . . . . . . .13

Overview of cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

About the connection illustrations . . . . . . . . . . . . . . . . . . . . 13

Connecting a VCR and antenna or Cable TV

(no Cable box) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting a VCR with S-video and a cable box . . . . . . . . 15

Connecting a DVD player with ColorStream®

(component video), a VCR, and a satellite receiver . . . . . . . 16

Connecting a device to the IR OUT infrared terminal using

the IR blaster cable for IR pass-through device

control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting a camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting an HDMI™ or DVI device to the HDMI

input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting a digital audio system . . . . . . . . . . . . . . . . . . . . 20

Connecting an audio system . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting a personal computer (PC) . . . . . . . . . . . . . . . . . 21

Chapter 3: Using the remote control . . . . . . . . . . . . . . . . . . .22

Preparing the remote control for use. . . . . . . . . . . . . . . . . . . 22

Installing the remote control batteries . . . . . . . . . . . . . . . . . 22

Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . 22

Learning about the remote control . . . . . . . . . . . . . . . . . . . . 23

Using the remote control to control your other devices . . . . 24

Remote Control functional key chart . . . . . . . . . . . . . . . . . . 25

Programming the remote control to control your other

devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Chapter 4: Menu layout and navigation . . . . . . . . . . . . . . . . .29

Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 30

Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 5: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .31

Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 31

Configuring the antenna input source for the ANT

terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Programming channels into the TV’s channel memory . . . . 32

Programming channels automatically . . . . . . . . . . . . . . 32

Manually adding and deleting channels in the channel

memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Labeling channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Setting the HDMI™ audio mode . . . . . . . . . . . . . . . . . . . . . . 34

Setting the Power-On Mode feature . . . . . . . . . . . . . . . . . . . 35

Viewing the digital signal meter. . . . . . . . . . . . . . . . . . . . . . 35

Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Chapter 6: Using the TV’s features . . . . . . . . . . . . . . . . . . . .37

Selecting the video input source to view . . . . . . . . . . . . . . . 37

Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 37

Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Tuning channels using the Channel Browser™ . . . . . . . 38

Tuning to the next programmed channel . . . . . . . . . . . . 40

Tuning to a specific channel (programmed or

unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Switching between two channels using Channel

Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Switching between two channels using SurfLock™. . . . 40

Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Scrolling the TheaterWide® picture

(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 42

Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 43

Selecting the cinema mode (480i and 1080i signals) . . . . . . 43

Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . . . 44

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 44

Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 45

Base closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Digital CC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

CC Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using the digital audio selector . . . . . . . . . . . . . . . . . . . 46

Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 47

Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 47

Using the StableSound® feature. . . . . . . . . . . . . . . . . . . 48

Selecting the optical audio output format . . . . . . . . . . . 48

Using the Dolby® Digital Dynamic Range

Control feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 49

If you cannot remember your PIN code. . . . . . . . . . . . . 49

Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 49

Blocking TV programs and movies by rating

(V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Downloading an additional rating system for blocking

TV programs and movies . . . . . . . . . . . . . . . . . . . . 50

Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Unlocking programs temporarily . . . . . . . . . . . . . . . . . . 52

Using the input lock feature . . . . . . . . . . . . . . . . . . . . . . 52

Using the control panel lock feature . . . . . . . . . . . . . . . 53

Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 53

Setting the PC Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Displaying TV status information. . . . . . . . . . . . . . . . . . . . . 55

Understanding the auto power off feature . . . . . . . . . . . . . . 55

Understanding the last mode memory feature . . . . . . . . . . . 55

Chapter 7: Using the TV’s advanced features . . . . . . . . . . . . . 56

Using the advanced picture settings features . . . . . . . . . . . . 56

Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 56

Using the static gamma feature . . . . . . . . . . . . . . . . . . . 56

Selecting the color temperature . . . . . . . . . . . . . . . . . . . 57

Selecting the lamp mode . . . . . . . . . . . . . . . . . . . . . . . . 57

Using CableClear® digital noise reduction . . . . . . . . . . 58

Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 58

Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 59

Using the advanced audio settings features . . . . . . . . . . . . . 59

Using the SRS WOW™ surround sound feature . . . . . . 59

Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 60

General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

(continued)

50HM67_EN.book Page 7 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Lamp unit replacement and care. . . . . . . . . . . . . . . . . . . . . . 63

Replacing the lamp unit

(User-replaceable component). . . . . . . . . . . . . . . . . 63

When to replace the lamp unit . . . . . . . . . . . . . . . . . . . . 63

How to replace the lamp unit . . . . . . . . . . . . . . . . . . . . . 64

Disposing of the used lamp unit. . . . . . . . . . . . . . . . . . . 65

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Limited United States Warranty

for DLP® Television Models . . . . . . . . . . . . . . . . . . . . . 67

Limited Canadian Warranty

for Toshiba Brand DLP® Television Models. . . . . . . . . 68

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

50HM67_EN.book Page 8 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 1: Introduction

Welcome to Toshiba

Thank you for purchasing this Toshiba TV, one of the most

innovative DLP® projection TVs on the market. This digital

television is capable of receiving analog basic, digital basic

and digital premium cable television programming by direct

connection to a cable system providing such programming. A

security card provided by your cable operator is required to

view encrypted digital programming. Certain advanced and

interactive digital cable services such as video-on-demand, a

cable operator's enhanced program guide and data-enhanced

television services may require the use of a set-top box. For

more information call your local cable operator.

Features of your new TV

The following are just a few of the many exciting features of

your new Toshiba widescreen, integrated HD, DLP®

projection TV:

•Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top

box (in most cases).

•Three HDMI™ digital, high-definition multimedia

interfaces 1080p input support (-page 19).

•Two sets of ColorStream® HD high-resolution component

video inputs (-page 16).

•SRS WOW™ audio technologies (-page 59).

•Digital Audio Out optical audio connection with Dolby®

Digital optical output format (-page 48).

•CableClear® digital picture noise reduction

(-page 58).

•PC IN (Analog RGB) computer terminal (-page 21).

•IR OUT infrared terminal using the IR blaster cable for IR

pass-through device control (-page 13).

•Channel Labeling allows you to put the Call Letters (e.g.

ABC, HBO, etc.) on the screen along with the station

numbers, so you always know what you’re watching

(-page 33).

•1080p output resolution (57HM167, 65HM167)

•720p output resolution (50HM67)

NOTICE OF POSSIBLE TV STAND INSTABILITY

DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH! Use this TV only with

the TOSHIBA TV stand listed in the

“Specifications” section of this manual. Use with other

stands may result in instability, causing possible injury or

death.

50HM67_EN.book Page 9 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 1: Introduction

Overview of steps for installing,

setting up, and using your new TV

Follow these steps to set up your TV and begin using its many

exciting features.

1Carefully read the important safety, installation, care, and

service information. Keep this manual for future

reference.

2Observe the following when choosing a location for the

TV:

•Read “Important notes about your DLP® projection

TV” (- page 6).

•Place the TV on the applicable optional TV stand listed

in the “Specifications” section (if available for this TV

model) or on a sturdy, level, stable surface that can

safely support the size and weight of the unit.

•Place the TV in a location where light does not reflect

on the screen.

•Place the TV far enough from walls and other objects to

allow proper ventilation. Inadequate ventilation may

cause overheating, which will damage the TV. THIS

TYPE OF DAMAGE IS NOT COVERED UNDER

THE TOSHIBA WARRANTY.

3Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

4BEFORE connecting cables or devices to the TV, learn

the functions of the TV’s connections and controls

(-pages 11–12).

5Connect your other electronic device(s) to the TV

(-pages 13–21).

6Install the batteries in the remote control (-page 22).

7See “Learning about the remote control” (-page 23) for

an overview of the buttons on the remote control.

8Program the remote control to operate your other

device(s) (-pages 24–28).

9AFTER connecting all cables and devices, plug in the

power cords for your TV and other devices.

10 After you plug in the TV power cord, the yellow LED

(on the TV front) will blink 3 times. Wait several seconds

until the yellow LED stops blinking and then press p on

the TV or remote control.

See “LED indications” (- page 62).

11 See “Menu layout and navigation” for a quick overview of

navigating the TV’s menu system (-page 29).

12 Program channels into the TV’s channel memory

(-page 32).

13 For details on using the TV’s features, see Chapters 6

and 7.

14 For help, refer to the Troubleshooting Guide, Chapter 8.

15 For lamp unit replacement instructions, see Chapter 9.

16 For technical specifications and warranty information, see

Chapter 9.

17 Enjoy your new TV!

50HM67_EN.book Page 10 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 1: Introduction

TV front and side panel controls and connections

Side panel

Right side of TV

Front of TV

Control panel

1Remote sensor (behind the screen) — Point the remote

control toward this area of the TV screen (- “Remote

control effective range” on page 22).

2Blue, Yellow, and Green/Red

See “LED indications” on page 62 for additional

information.

3POWER — Press to turn the TV on and off.

If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn off the

TV, press and hold the POWER button on the TV control

panel for 5 or more seconds to reset the TV.

4CHANNEL Uu — When no menu is on-screen, these

buttons change the channel (programmed channels only;

-page 32).

5VOLUME + – — These buttons adjust the volume level.

6INPUT — Repeatedly press to change the source you are

viewing (ANT, VIDEO 1, VIDEO 2, ColorStream

HD1, ColorStream HD2, HDMI 1, HDMI 2, HDMI 3,

PC).

7MENU (ENTER) — Press to access the menu system

(-pages 29–30). When a menu is on-screen, the MENU

button on the TV’s control panel functions as the ENTER

button.

8ARROWS BbC c — When a menu is on-screen, these

buttons function as up/down/left/right menu navigation

buttons.

9EXIT — Press to instantly close an on-screen menu.

10 VIDEO-2 IN — The side panel A/V connections are

referred to as “VIDEO 2” and include standard A/V

inputs plus an optional S-video input.

Note: Standard (composite) video and S-video cables

carry only video information; separate audio cables are

required for a complete connection.

50HM67_EN.book Page 11 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 1: Introduction

TV back panel connections

For an explanation of cable types and connections, see pages 13–21.

6 7 8

1ColorStream® HD-1 and ColorStream® HD-2 —

Two sets of ColorStream® high-definition component

video inputs (with standard stereo audio inputs) for

connecting devices with component video output, such as

a Toshiba DVD player with ColorStream®.

Note: Component video cables carry only video

information; separate audio cables are required for a

complete connection.

2VIDEO-1 IN — Standard (composite) video and standard

audio inputs for connecting devices with composite video

output.

3PC IN — For use when connecting a personal computer.

PC audio input terminals are shared with HDMI-1 analog

audio input terminals, and their use can be configured in

the Audio Setup menu (-page 54).

4HDMI™ IN — High-Definition Multimedia Interface

input receives digital audio and uncompressed digital

video from an HDMI device or uncompressed digital

video from a DVI device. Also see item 3. HDMI

connection is necessary to receive 1080p signals.

5ANT — Antenna input that supports analog (NTSC) and

digital (ATSC) off-air antenna signals and analog and

digital Cable TV (QAM) signals.

6Fixed Audio OUT — Analog audio outputs for

connecting an audio amplifier.

7IR OUT — For controlling infrared remote-controlled

devices through the TV. You can connect up to two

devices with an IR blaster cable, and then control the

devices using the TV’s IR pass-through features.

8Digital Audio OUT — Optical audio output in Dolby

Digital or PCM (pulse-code modulation) format for

connecting an external Dolby Digital decoder, amplifier,

A/V receiver, or home theater system with optical audio

input.

9Service port (behind the cover) — For service use

only. Used for updating the television’s firmware.

HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are registered trademarks of Dolby

Laboratories.

50HM67_EN.book Page 12 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Overview of cable types

Coaxial (F-type) cable

Coaxial (F-type) cable is used for connecting your antenna,

cable TV service, and/or cable converter box to the ANT input

on your TV.

Standard A/V cables (red/white/yellow)

Standard A/V cables (composite video) usually come in sets of

three, and are for use with video devices with analog audio and

composite video output. These cables (and the related inputs

on your TV) are typically color-coded according to use: yellow

for video, red for stereo right audio, and white for stereo left

(or mono) audio.

S-video cable

S-video cable is for use with video devices with S-video

output. Separate audio cables are required for a complete

connection.

Note: An S-video cable provides better picture performance

than a composite video cable. If you connect an S-video cable,

be sure to disconnect the standard (composite) video cable or

the picture performance will be unacceptable.

Component video cables (red/green/blue)

Component video cables come in sets of three and are for use

with video devices with component video output.

(ColorStream® is Toshiba’s brand of component video.) These

cables are typically color-coded red, green, and blue. Separate

audio cables are required for a complete connection.

Note: Component video cables provide better picture

performance than a standard (composite) video or S-video

cable.

HDMI™ cable

HDMI (High-Definition Multimedia Interface) cable is for use

with devices with an HDMI output. An HDMI cable delivers

digital audio and video in its native format. This cable carries

both video and audio information; therefore, separate audio

cables are not required for a complete HDMI device

connection (-page 19 and page 21).

Note: HDMI cable provides better picture performance than a

standard (composite) video or S-video cable.

Dual-wand IR blaster cable

Dual-wand IR blaster cable is for use with video devices with

IR (infrared) remote control. This cable can be used with the

TV’s IR pass-through feature (-page 17).

To obtain IR blaster cable:

Visit www.ceaccessories.toshiba.com.

Optical audio cable

Optical audio cable is for connecting receivers with Dolby

Digital or PCM (pulse-code modulation) optical audio input to

the TV’s DIGITAL AUDIO OUT terminal (-page 20).

Analog RGB (15-pin) computer cable

Analog RGB (15-pin) computer cable is for connecting a PC to

the TV’s PC IN terminal (-page 21).

About the connection illustrations

You can connect different types and brands of devices to your

TV in several different configurations. The connection

illustrations in this manual are representative of typical device

connections only. The input/output terminals on your devices

may differ from those illustrated herein. For details on

connecting and using your specific devices, refer to each

device’s owner’s manual.

50HM67_EN.book Page 13 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a VCR and antenna or Cable TV (no Cable box)

IN from ANT

VIDEO AUDIO

OUT to TV

OUT

CH 3

CH 4

TV back panel

Stereo VCR

From Cable TV or antenn

You will need:

•coaxial cables

•standard A/V cables

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) to VIDEO 2

on the side panel (instead of to VIDEO 1). Do not connect

both types of video cable to VIDEO 2 at the same time or

the picture performance will be unacceptable.

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

To view the antenna or Cable signal:

Select the ANT video input source on the TV.*

To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on

the TV.*

*To select the video input source, press INPUT on the remote control

(-page 23). To program the TV remote control to operate other

devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

50HM67_EN.book Page 14 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a VCR with S-video and a cable box

An S-video connection will provide better picture performance than a standard (composite) video cable.

IN from ANT

VIDEO AUDIO

OUT to TV

OUT

CH 3

CH 4

OUT

CH 3

CH 4

Cable box

From Cable T

stereo VCR

TV back panel

TV right side panel

You will need:

•coaxial cables

•S-video cable

– Do not connect both types of video cable to VIDEO 2 at

the same time or the picture performance will be

unacceptable.

•standard audio cables

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

Note: When you use a Cable box, you may not be able to use

the remote control to program or access certain features on the

TV.

To view basic and premium Cable channels:

Turn OFF the VCR. Select the ANT video input source on the

TV.* Tune the TV to channel 3 or 4 (whichever channel the

Cable box output is set to). Use the Cable box controls to

change channels.

To view the VCR:

Turn ON the VCR. Select the VIDEO 2 video input source on

the TV.*

*To select the video input source, press INPUT on the remote control

(-page 23). To program the TV remote control to operate other

devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

50HM67_EN.book Page 15 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a DVD player with ColorStream® (component video), a VCR,

and a satellite receiver

Your TV has two sets of ColorStream® (component video) inputs.

IN from ANT

VIDEO AUDIO

OUT to TV

OUT

CH 3

CH 4

VIDEO

OUT

COMPONENT VIDEO

PBPR

AUDIO

OUT

S-VIDEO

OUT

S-VIDEO

OUT

VIDEO

OUT

AUDIO

OUT

COMPONENT VIDEO

Satellite

PBPR

TV back panel

Stereo VCR

From antenn

Satellite receiver with component video

From satellite dish

DVD player with component video

You will need:

•coaxial cables

•standard A/V cables

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) to VIDEO 2

on the side panel (instead of to VIDEO 1). Do not connect

both types of video cable to VIDEO 2 at the same time or

the picture performance will be unacceptable.

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

•standard audio cables

•component video cables

– You can connect the component video cables (plus audio

cables) from the DVD player or satellite receiver to either

set of ColorStream terminals on the TV (HD-1 or HD-2).

The ColorStream HD-1 and HD-2 terminals can be used

with Progressive (480p, 720p) and Interlaced (480i, 1080i)

scan systems. A 1080i signal will provide the best picture

performance (1080p is not supported).

– If your DVD player or satellite receiver does not have

component video, connect a standard A/V cable to

VIDEO 2 on the side panel. If your DVD player has HDMI

video, see page 19.

To view antenna or Cable channels:

Select the ANT video input source on the TV.*

To view the DVD player:

Turn ON the DVD player. Select the ColorStream HD-1

video input source on the TV.*

To view satellite programs using the component video

connections:

Turn on the satellite receiver. Select the ColorStream HD-2

video input source on the TV.*

To view the VCR or view and record antenna

channels:

Turn ON the VCR. Tune the VCR to the channel you want to

watch. Select the VIDEO 1 video input source on the TV.*

To record a TV program while watching a DVD:

Turn ON the VCR. Tune the VCR to the channel to record.

Select the ColorStream HD-1 video input source on the TV*

to view the DVD.

*To select the video input source, press INPUT on the remote control

(-page 23). To program the TV remote control to operate other

devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

50HM67_EN.book Page 16 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a device to the IR OUT

infrared terminal using the IR

blaster cable for IR pass-through

device control

You can use the TV’s IR OUT terminal (infrared pass-

through) to remotely operate (through the TV) many infrared

remote-controlled devices (such as Toshiba infrared remote-

controlled VCRs or DVD players) enclosed within an

entertainment center or similar cabinet. Without the IR OUT

connection, the device typically would need to be visible to

operate it remotely.

You will need:

•dual-wand IR blaster cable (- page 13)

•other audio/video cables as required to connect the device(s)

to the TV (- pages 14–19)

To connect the IR blaster cable:

1Locate the infrared sensor on the front of your device.

This sensor is marked on some devices.*

2Align one of the IR blaster cable’s wands about 1 inch

away from the infrared sensor on the front of the device

and attach it using double-sided mounting tape. If you

have a second device, attach the second wand in a similar

manner. (See illustration.)

Note: If you do not have a second device, coil the second

wand with a rubber band and leave it behind the TV.

3Plug the IR blaster cable’s plug into the TV’s IR OUT

terminal.

To control the device(s):

Point either the device’s remote control or the TV remote

control (that you previously programmed to operate the

device; - Chapter 3) toward the front of the TV and press the

button for the desired function. The signal passes from the

remote control through the TV to the device via the IR blaster

cable.

Note:

•If you use the device’s remote control to operate the device,

you also will need to use the TV’s remote control to operate

the TV.

•The IR pass-through feature does not support all

IR-controlled devices; satisfactory performance may not be

attainable with certain devices.

Front of IR-controlled DVD player (for example)

Front of IR-controlled audio device (for example)

Infrared

sensor

IR blaster cable wand

(approx.1 inch from device)

TV back panel

*If you cannot locate the device’s infrared sensor:

1Turn OFF the device.

2Starting at the lower left corner of the device, place the

end of the device’s remote control (with the infrared

emitter) so it touches the front of the device and press

POWER. (Do not use the TV’s remote control for this

step.)

3If the device turns on, the point at which the remote

control touched the device is the location of the sensor.

4If the device does not turn on, move the remote control

slightly to the right and press POWER again.

5Repeat step 4 until you locate the device’s infrared

sensor.

50HM67_EN.book Page 17 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a camcorder

You will need:

•standard A/V cables

– For better picture performance, if your camcorder has

S-video, connect an S-video cable (plus the audio

cables).

To view the camcorder video:

Select the VIDEO 2 video input source on the TV.*

*To select the video input source, press INPUT on the remote control

(-page 23). To program the TV remote control to operate other

devices, see Chapter 3.

VIDEO AUDIO

OUT

VIDEO 2 inputs on TV right side panel

Camcorder

50HM67_EN.book Page 18 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting an HDMI™ or DVI device

to the HDMI input

The HDMI input on your TV receives digital audio and

uncompressed digital video from an HDMI source device, or

uncompressed digital video from a DVI (Digital Visual

Interface) source device.

This input is designed to accept HDCP (High-Bandwidth

Digital-Content Protection) program material in digital form

from EIA/CEA-861-861B–compliant[1] consumer electronic

devices (such as a set-top box or DVD player with HDMI or

DVI output).

The HDMI input will accept and display 480i, 480p, 720p,

1080i, and 1080p signals.

Note: To connect a PC to the HDMI input, see page 21.

To connect an HDMI device, you will need:

•one HDMI cable (type A connector) per HDMI device

– For proper operation, it is recommended that you use an

HDMI cable with the HDMI Logo (HDMI™). You should use

an HDMI cable shorter than 16.4 ft (5m) for 1080p input

signals.

– HDMI cable transfers both video and audio. Separate

analog audio cables are not required (see illustration).

– See “Setting the HDMI™ audio mode” (-page 34).

To view the HDMI device video:

Select the HDMI 1, HDMI 2, or HDMI 3 video input source on

the TV.*

Note: If the audio output mode of the HDMI device is other

than the L-PCM mode, the TV speakers will not output sound.

*To select the video input source, press INPUT on the remote control

(-page 23). To program the TV remote control to operate other

devices, see Chapter 3.

To connect a DVI device, you will need:

•one HDMI-to-DVI adapter cable (HDMI type A connector)

per DVI device

– For proper operation, the length of an HDMI-to-DVI

adapter cable should not exceed 9.8 ft (3m). The

recommended length is 6.6 ft (2m).

•one pair of standard analog audio cables per DVI device

– An HDMI-to-DVI adapter cable transfers video only.

Separate analog audio cables are required (see

illustration).

– See “Setting the HDMI™ audio mode” (-page 34).

Note: To ensure that the HDMI or DVI device is reset properly,

it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the

TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the

HDMI or DVI device first, and then the TV.

[1] EIA/CEA-861-861B compliance covers the transmission of

uncompressed digital video with high-bandwidth digital content

protection, which is being standardized for reception of high-

definition video signals. Because this is an evolving technology, it

is possible that some devices may not operate properly with the TV.

HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

VIDEO AUDIO

OUT

HDMI

OUT

HDMI device

TV back panel

VIDEO AUDIO

OUT

DVI/ HDCP

OUT

DVI device

TV back panel

50HM67_EN.book Page 19 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a digital audio system

The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby®*

Digital g or 2-channel down-mixed PCM (pulse-code

modulation) signal for use with an external Dolby® Digital

decoder or other external audio system with optical audio

input.

You will need:

•optical audio cable (Use an optical audio cable that has the

larger “TosLink” connector and not the smaller “mini-

optical” connector.)

To control the audio:

1Turn on the TV and the digital audio device.

2Press Y on the TV’s remote control and open the Audio

menu.

3Highlight Audio Setup and press T.

4In the Optical Output Format field, select either

Dolby Digital or PCM, depending on your device

(- “Selecting the optical audio output format” on

page 48).

Note:

•Some audio systems may not be compatible with Dolby

Digital bitstream signals. Older audio systems that are not

compatible with standard optical out signals may not work

properly, creating a high noise level that may damage

speakers or headphones. THIS DAMAGE IS NOT COVERED

BY YOUR WARRANTY.

•The DIGITAL AUDIO OUT terminal may not output some

digital audio sources because of copy restrictions.

*Manufactured under license from Dolby Laboratories.

Dolby, and the double-D symbol are registered trademarks of Dolby

Laboratories.

Connecting an audio system

This connection allows you to use external speakers with an

external analog audio amplifier to adjust the sound level.

You will need:

•standard audio cables

To control the audio:

1Turn on the TV and the stereo amplifier.

2Minimize the sound volume from the TV’s built-in

speakers and control the volume level using the

amplifier’s remote control.

LINE IN

Optical

Audio IN

Dolby Digital decoder or

other digital audio system

TV back panel

Audio

Audio Settings

Digital Audio Selector

Advanced Audio Settings

Audio Setup

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

LINE IN

Analog audio amplifier

TV back panel

50HM67_EN.book Page 20 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 2: Connecting your TV

Connecting a personal computer

(PC)

To connect a PC to the PC IN terminal on the TV:

When connecting a PC to the PC IN terminal on the TV, use an

analog RGB (15-pin) computer cable and a PC audio cable.

•To use a PC, set the monitor output resolution on the PC

before connecting it to the TV. The following signals can be

displayed:

Other formats or non-standard signals will not be displayed

correctly.

•To display the optimum picture, use the PC setting feature

(- “Using the PC settings feature” on page 53).

Note:

•The PC audio input terminals on the TV are shared with the

HDMI-1 analog audio input terminals (- page 54).

•Some PC models cannot be connected to this TV.

•An adapter is not needed for computers with a DOS/V

compatible mini D-sub15-pin terminal.

•Depending on the DVD’s title and the specifications of the

PC on which you are playing the DVD-Video, some scenes

may be skipped or you may not be able to pause during

multi-angle scenes.

To connect a PC to the HDMI terminal on the TV:

When connecting a PC to the HDMI terminal on the TV, use

an HDMI-to DVI adapter cable and analog audio cables.

If connecting a PC with an HDMI terminal, use an HDMI cable

(type A connector). Separate analog cables are not necessary

(- page 19).

•The following signal formats can be displayed:

Note: The edges of the images may be hidden.

Format Resolution V. Frequency

VGA 640 × 480 60Hz

SVGA 800 × 600 60Hz

XGA 1024 × 768 60Hz

Conversion adapter

(if necessary)

PC audio

cable

PC audio

output

Computer

TV back panel

Format Resolution V. Frequency

VGA 640 × 480 59.94/60Hz

480i 720 × 480 59.94/60Hz

480p 720 × 480 59.94/60Hz

720p 1280 × 720 59.94/60Hz

1080i 1920 × 1080 59.94/60Hz

1080p 1920 × 1080 59.94/60Hz

PC audio

cable

PC audio

output

Computer

TV back panel

50HM67_EN.book Page 21 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Preparing the remote control

for use

Your TV remote control can operate your TV and many other

devices such as cable converter boxes, satellite receivers,

VCRs, DVD players, and HTIBs (home theater in a box), even

if they are different brands.

If you have a Toshiba device:

Your TV remote control is preprogrammed to operate most

Toshiba devices (-page 26).

If you have a non-Toshiba device or a Toshiba device

that the remote control is not preprogrammed to

operate:

You can program the TV remote control so it will operate the

other device (-pages 24–28).

Installing the remote control

batteries

1Remove the battery cover from the back of the remote

control.

2Install two “AAA” size batteries, making sure to match

the + and – signs on the batteries to the signs on the battery

compartment.

3Reinsert the battery cover in the remote control until the

tab snaps.

Caution: Never throw batteries into a fire.

Note:

•Be sure to use AAA size batteries.

•Dispose of batteries in a designated disposal area.

•Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in

accordance with applicable laws and regulations.

•If the remote control does not operate correctly, or if the

operating range becomes reduced, replace batteries with

new ones.

•When necessary to replace batteries in the remote control,

always replace both batteries with new ones. Never mix

battery types or use new and used batteries in combination.

•Always remove batteries from the remote control if they are

dead or if the remote control is not to be used for an

extended period of time. This will prevent battery acid from

leaking into the battery compartment.

Remote control effective range

For optimum performance, aim the remote control directly at

the TV and make sure there is no obstruction between the

remote control and the TV.

Squeeze tab

and lift cover.

16.4 ft (5m)

Point remote control

toward remote sensor

on front of TV.

50HM67_EN.book Page 22 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Learning about the remote control

The buttons used for operating the TV only are described here.

For a complete list of the remote control’s functions, see the

remote control functional key chart (-page 25).

Note: The error message “Not Available” may appear if you

press a key for a function that is not available.

1POWER turns the TV on and off. Press p to turn on the

TV, The blue LED indicator on the TV front will be

illuminated. Press p again to turn off the TV.

Note: The Power-On Mode setting will affect the amount

of time it takes for the picture to appear when you turn on

the TV (-page 35).

2PIC MODE selects the picture mode (-page 44).

3SLEEP accesses the sleep timer (-page 54).

4PIC SIZE cycles through the picture sizes: Natural,

TheaterWide 1/2/3, Full, and 4:3 HD (-page 41).

5Channel Numbers (0–9, –/100) directly tune

channels. The = button is used to tune digital channels

(-page 40) or to edit the Favorites List (-page 38).

6INPUT selects the video input source (-page 37).

7CH Bb cycles through programmed channels when no

menu is on-screen (-page 32).

8VOL + – adjusts the volume level.

9FAV BROWSER accesses the Favorites List in the

Channel Brower™ (-page 38).

10 RECALL displays TV status information (-page 55).

11 CH RTN returns to the last viewed channel or source

(-page 40).

12 MUTE reduces or turns off the sound (-page 46).

13 INFO displays TV status information as well as program

details, when available (-page 55).

14 3C / #c While watching TV, these buttons open the

Channel Browser™ and tune to the previous/next channel

in the channel history (-page 39). (Also see “Arrow

buttons.”)

15 Arrow buttons (BbC c) When a menu is on-screen,

these buttons select or adjust programming menus. (Also

see 3C/#c.)

16 ENTER activates highlighted items in the main menu

system.

17 MENU accesses the main TV menu system (-pages 29

and 30).

18EXIT closes on-screen menus.

19 MODE SELECT switch switches between TV,

CABLE/SAT, AUX 1, and AUX 2 modes (-page 24).

Set to “TV” to control the TV.

50HM67_EN.book Page 23 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Using the remote control to control

your other devices

If you have a non-Toshiba device or a Toshiba device that the

remote control is not preprogrammed to operate, you must first

program the remote control to recognize the device (if you

have not already done so) (-pages 26–28).

To use your TV remote control to operate a:

•Cable converter box or satellite receiver, set the MODE

SELECT switch to CABLE/SAT.

•VCR, set the MODE SELECT switch to AUX 1.

•DVD player or HTIB, set the MODE SELECT switch to

AUX 2.

Note: Even after the TV remote control is programmed, it may

not operate certain features on any other devices. If this

happens and you wish to use those features, you will need to

use the device’s original remote control.

1POWER Turns the selected device on and off.

2Channel Numbers (0-9) Press to directly access

channels (as opposed to < ,).

3+10 Press to directly access DVD chapters higher than 10.

4TOP MENU Accesses a DVD’s top menu.

5CH Bb For channels programmed into the channel

memory (-page 40):

B selects the next higher channel.

b selects the next lower channel.

6GUIDE Displays the channel guide in the CABLE/SAT

mode.

SET UP Accesses a DVD’s setup menu in the AUX

mode.

7INFO Displays TV status information on-screen.

8BbC c Press to navigate DVD menus (may not work on

some DVD players).

9ENTER Required by some satellite receivers and DVD

players to activate certain functions.

10 DVD CLEAR Press to reset the title and chapter number.

11 PLAY Begins playback of a tape or DVD.

12 PAUSE Press during play or record mode to pause the

picture; press again to restart.

13 STOP Stops the tape or DVD.

14 SKIP z Skips forward to locate later DVD chapters.

15 FF Fast-forwards the tape or DVD. (Press during play

mode to view the picture moving rapidly forward.)

16 SKIP Z Skips back to beginning of current DVD

chapter, or locates previous chapters.

17 REW Rewinds/reverses the tape or DVD. (Press during

play mode to view the picture moving rapidly backward.)

18TV/VCR To view one program while recording another,

press to select TV mode.

SEARCH selects a specific DVD chapter, title or time.

19 REC Starts tape recording.

20 MODE SELECT switch Set to “TV” to control the TV;

“CABLE/SAT” to control a cable converter box or

satellite receiver; “AUX 1” to control a VCR; “AUX 2” to

control a DVD player or HTIB.

Point the remote control

directly at the device.

50HM67_EN.book Page 24 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Remote Control functional key chart

Note:

•“---” = key does not send a signal in that remote control mode.

•“sTV” = key will affect the TV, even though the remote control is in another mode.

•* Not available for your TV.

REMOTE CONTROL KEY Toshiba TV CABLE SAT (satellite) AUX 1 (VCR) AUX 2 (DVD or HTIB)

POWER Power Power Power Power Power

SLEEP Sleep timer s TV s TV s TV s TV

PIC SIZE Picture size s TV s TV s TV s TV

PIC MODE PIC MODE s TV s TV s TV s TV

1-9 Digit 1-9 Digit 1-9 Digit 1-9 Digit 1-9 Digit 1-9

0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0

100/–/+10 – (sub CH) --- – (sub CH) 100 +10

INPUT TV/Video select s TV s TV s TV s TV

FAV BROWSER/

TOP MENU

FAV BROWSER

DVD TOP Menu* --- --- --- Top Menu

MUTE Sound mute s TV s TV s TV s TV

SET UP/GUIDE Guide* --- SAT Guide --- Setup

VOL + – Volume up/down s TV s TV s TV s TV

CHBb Channel

up/down

Channel

up/down

Channel

up/down

Channel

up/down ---

RECALL RECALL s TV s TV s TV s TV

CH RTN/DVD RTN Previous channel

DVD previous menu* --- --- --- DVD Return

INFO Info --- Info --- Display

ENTER Enter --- Select, Enter --- Enter

Bb Menu up/down --- Menu

up/down --- Menu up/down

C 3Menu left/

Channel Browser™--- Menu left --- Menu left

c #Menu right/

Channel Browser™--- Menu right --- Menu right

MENU Menu --- Action Menu --- DVD Menu

EXIT/DVD CLEAR Exit

DVD clear* --- Exit --- DVD Clear

PAUSE/STEP Pause* --- --- Pause Pause

PLAY Play* --- --- Play Play

STOP Stop* --- --- Stop Stop

SKIP ZSkip REV* --- --- --- Skip REV

SKIP zSkip FWD* --- --- --- Skip FWD

REW Rewind* --- --- Rewind Rewind

FF Fast FWD* --- --- Fast FWD Fast FWD

TV/VCR/

SEARCH DVD search* --- --- TV/VCR DVD search

REC REC MENU* --- --- Record (2 click) ---

SLOW – SLOW REW* --- --- --- ---

SLOW + SLOW FWD* --- --- --- ---

ANGLE Angle* --- --- --- DVD Angle

SUB TITLE Sub title* --- --- --- DVD Sub title

AUDIO Audio* --- --- --- DVD Audio

EJECT Eject* --- --- --- DVD Eject

50HM67_EN.book Page 25 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Programming the remote control

to control your other devices

Your Toshiba TV remote control is preprogrammed to operate

most Toshiba devices. To program your TV remote control to

operate a non-Toshiba device (or a Toshiba device that it is not

preprogrammed to operate), follow the steps below. For details

on using the remote control to operate the device, see page 24.

1In the remote control code table (-page 27), find the

code for your device. If more than one code is listed, try

each one separately until you find one that works.

2Set the MODE SELECT switch to the type of device

you are programming the remote control to operate —

CABLE/SAT (for a cable converter box or satellite

receiver), AUX 1 (for a VCR or TV/VCR combo), or

AUX 2 (for a DVD player or HTIB [home theater in a

box]).

3While holding down E, press the Channel Number

buttons to enter the 3-digit code for your device.

4To test the code, turn on the device, point the remote

control at it, and press p. See notes below.

•If the correct code was entered, the device will turn off.

•If the device does not respond, repeat steps 1–4 using

another code.

•If the device does not respond to another code, you will

need to use the remote control that came with the

device.

5Remember to set the MODE SELECT switch back to

“TV” to control the TV.

6For future reference, write down the code(s) you used:

Note:

•In addition to POWER, confirm that all necessary keys on the

TV remote control operate your device. If some keys are not

operational, repeat the device code setup using another

code (if other codes are listed for your device). If, after trying

all listed codes, the necessary keys do not operate your

device, use the device’s original remote control.

•Every time you change the batteries, you will need to

reprogram the remote control.

•Some newer VCRs respond to either of two codes. These

VCRs have a switch labeled “VCR1/VCR2.” If your VCR has

this kind of switch and does not respond to the codes for

your VCR brand, set the switch to the other position (“VCR1”

or “VCR2”) and reprogram the remote control.

DEVICE CODE DEVICE CODE

50HM67_EN.book Page 26 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Remote control codes

In some cases you may not be able to

operate your device with the TV

remote control. Your other device may

use a code that is not recognized by the

TV remote control. If this happens, use

the device’s remote control.

Cable converter box

ABC 061, 062, 063, 082,

084, 087, 092,

096, 098

Archer 065, 092, 097, 099

Cableview 064, 094

Century 092

Citizen 090, 092, 097

Contec 083, 085, 086, 088,

093, 098

Diamond 093

GE 061, 062

Gemini 069, 070, 094

Hamlin 093

Hitachi 062, 095, 096

Jasco 097

Motorola/GI/Jerrold 062, 069, 071, 082,

086, 089, 096, 107

Magnavox 072, 096

Memorex 092, 104

Multi Canal 090

Novavision 101

Panasonic 081, 083, 085

Philco 087

Philips 066, 067, 068, 070,

072, 073, 074, 075,

092

Pioneer 076, 077

Proscan 061, 062

Radio Shack 092, 097, 099

RCA 064, 081

Realistic 065

Recoton 102

Samsung 077, 090

Scientific Atlanta 063, 078, 079, 080,

088, 098, 101, 105

Sears 095

Signature 062

Signature 2000 096

Sprucer 081, 085

Starcom 069, 082, 087, 096,

103, 104

Stargate 069, 090

Sylvania 095, 100

TeleView 090

Texscan 100

Tocom 071, 084, 085

U. S. Electronics 087, 096, 098

United Cable 082

Universal 065, 092, 097, 099,

102, 103

Wards 096

Satellite receiver

Alphastar 038, 059

Chaparral 034

DISH Network 057

Drake 020, 040, 044, 046,

050, 053

Echostar 018, 041, 051

Express Vu 057

Fujitsu 027

GE 008, 009, 013

General Instruments 010, 011, 012, 022,

023, 031, 049

Hitachi 033

Hughes 033

Hughes Network

Systems 019

Intersat 048

Janeil 027

JVC 017, 057

Kenwood 029

Magnavox 060

Optimus 058

Pansat 036, 052

Primestar 015, 042

Proscan 008, 009, 013

Radio Shack 022, 023, 030

RCA 008, 009, 013, 016

Realistic 030

Samsung 059

Sony 014, 055

Star Choice 057, 106

Star Trak 025, 026, 037, 054

STS 024

Toshiba 000, 001, 002, 003,

004, 005, 006, 007,

020, 031, 056

Uniden 021, 028, 030, 032,

035, 039, 043, 045,

047, 058

Zenith 027

TV/VCR Combo

Action 078

GE 059, 062

Goldstar 065

Panasonic 065

Precision 078

Quasar 065

Realistic 079

Sony 074

Toshiba 057

Zenith 065

Totevision 009, 010, 065

DVD/VCR Combo

Go Video DVD=087,

VCR=081

JVC DVD=088,

VCR=082

RCA DVD=089,

VCR=083

Samsung DVD=090,

VCR=084

Sanyo DVD=091,

VCR=085

Zenith DVD=092,

VCR=086

DVD player

Aiwa 006, 015

Apex 016, 017

BOSE 097

Broksonic 018

Clarion 019

Classic 020

Daewoo 021

Denon 022, 023, 024, 025

Emerson 026, 027

Fisher 028

Funai 027

GE 001, 029, 030

Go Video 087

GPX 031

Hitachi 005, 032, 033, 034,

035

JVC 003, 007, 036, 042,

088

Kenwood 037

Konka 008, 009

Magnavox 004, 038

Memorex 039

Mintek 040

NAD 026

Nakamichi 041

Norcent 043

Onkyo 044

Oritron 058

Panasonic 010, 045, 046, 047,

048, 049, 050

Philips 004, 051

Pioneer 052, 053, 054, 055

Proscan 001, 056

Qwestar 057, 058

RCA 001, 002, 059, 089

Sampo 060

Samsung 061, 062, 086, 090

Sansui 073

Sanyo 063, 091

Sharp 064, 067

Sherwood 074

Sony 011, 012, 065, 066,

068, 069, 070

Sylvania 027

Teac 071

Technics 072

Techwood 075

Toshiba 000, 013, 076, 077,

078

Yamaha 079, 080, 081

Zenith 014, 082, 092

Portable DVD player

Aiwa 093

Audiovox 094, 095

Panasonic 024, 096, 099

RCA 098

VCR

Admiral 049

Aiko 019

Aiwa 018

Akai 003, 004, 037, 038,

039, 058, 069

Audiovox 010

Bell & Howell 007, 068

Broksonic 008, 017

Calix 010

Carver 026

CCE 019

Citizen 009, 010, 011, 012,

013, 014, 015, 019,

057, 073

Colortyme 005

50HM67_EN.book Page 27 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 3: Using the remote control

Craig 009, 010, 016, 061,

065, 079

Curtis Mathes 001, 005, 009, 012,

014, 040, 048, 053,

056, 057

Daewoo 011, 013, 015, 017,

018, 019, 057, 078

Daytron 078

Denon 063

Dimensia 001, 048

Electrohome 010, 020, 065

Emerson 003, 008, 010, 011,

017, 018, 020, 028,

039, 054, 057, 062,

065, 068, 072

Fisher 007, 016, 021, 022,

023, 057, 064, 068,

070, 071, 079

Fuji 004, 041

Funai 018, 073

Garrard 018

GE 001, 002, 009, 040,

042, 048, 056

Go Video 056, 059, 061, 081

Goldstar 005, 010, 014, 054,

056, 065, 067

Gradiente 018, 065

Harman Kardon 005

Hitachi 024, 025, 035, 037,

042, 063, 070, 080

JBL 076

JC Penney 005, 006, 007, 008,

009, 010, 023, 024,

025, 026, 035, 056,

061, 063, 065

Jensen 024, 025, 037, 050

JVC 005, 006, 007, 014,

037, 043, 055, 062,

063, 068, 082

Kenwood 005, 006, 007, 012,

014, 037, 043, 050,

053, 068, 071

Kodak 010

LG 010

Lloyds 053, 073, 079

Logik 061

LXI 010

Magnasonic 061, 065, 078

Magnavox 026, 027, 034, 044,

057, 061, 072

Marantz 005, 006, 007, 012,

014, 026, 053, 067

Memorex 007, 009, 010, 016,

018, 034, 049, 063,

065, 066, 068, 075,

079

MGA 020, 028, 039

MGN 056

Minolta 024, 025, 035, 063

Mitsubishi 020, 024, 025, 028,

039, 043, 065

Montgomery Ward 049

Motorola 049

MTC 009, 046, 061

Multitech 009, 012, 018

NEC 005, 006, 007, 012,

014, 037, 043, 053,

054, 067, 070

Nikko 010

Noblex 009

Optimus 010, 049, 065

Optonica 031

Orion 054, 057, 062, 065,

068, 072

Panasonic 036, 045, 046, 057,

061, 072, 079

Pentax 012, 024, 025, 035,

042, 053, 063

Pentex Research 014

Philco 026, 027, 063

Philips 026, 031, 044, 057

Pioneer 006, 024, 043, 055

Portland 012, 013, 015

Proscan 001, 002, 048

Proton 061

Quasar 045

Radio Shack 010, 031, 065

Radio Shack/Realistic 007, 009, 010, 016,

018, 020, 021, 022,

031, 049

Radix 010

RCA 001, 002, 003, 009,

024, 025, 029, 035,

040, 042, 045, 048,

055, 056, 063, 071,

083

Realistic 007, 009, 010, 011,

016, 018, 020, 021,

022, 031, 049, 051,

056, 060, 065, 075,

079

Ricoh 047

Runco 034

Samsung 009, 011, 038, 056,

073, 084

Sansui 006, 037, 043, 061

Sanyo 007, 009, 016, 054,

064, 068, 071, 075,

079, 085

Scott 008, 011, 017, 028,

030, 057, 065, 072

Sears 007, 010, 016, 021,

022, 023, 024, 025,

035, 053, 057, 063,

064, 065, 068, 071,

075, 079

Sharp 013, 020, 031, 049,

051, 060, 066

Shintom 004, 025, 032, 061

Signature 049

Signature 2000 075

Singer 047, 061

Sony 004, 032, 033, 041,

052, 058, 070, 074,

076, 077, 080

STS 035

Sylvania 018, 026, 027, 028,

044, 072

Symphonic 018, 050, 051, 053,

073, 079

Tandy 007

Tashiko 010

Tatung 037

Teac 018, 029, 037

Technics 036

Teknika 010, 018, 065

Toshiba 000, 011, 021, 023,

024, 028, 030, 039,

057, 074, 078, 079

Totevision 009, 010, 065

Unitec 073

Unitech 009

Vector Research 005, 006, 011, 012,

053

Video Concepts 005, 006, 011, 012,

039, 053

Wards 009, 010, 011, 016,

018, 020, 024, 025,

031, 035, 049, 051,

056, 057, 060, 065,

066, 079

White Westinghouse 073

XR-1000 018

Yamaha 005, 006, 007, 014,

037, 053

Zenith 004, 032, 034, 041,

047, 069, 086

HTIB

Lasonic 083

Panasonic 084

Venturer 085

50HM67_EN.book Page 28 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 4: Menu layout and navigation

Main menu layout

The tables below and on the next page provide a quick overview of your TV’s menu system.

To open the main menus (illustrated below), press Y on the remote control or TV control panel.

Icon Item Option Page

Mode SSports/Standard/Movie/Preference 44

Picture Settings S[Opens the Picture Settings menu] 44

Noise Reduction S[Opens the Noise Reduction menu] 58

Game Mode SOn/Off 59

Theater Settings S[Opens the Theater Settings menu] 41

Digital Audio Selector S[Launches the temporary Audio Selector] 46

Audio Settings S[Opens the Audio Settings menu] 47

Advanced Audio Settings S[Opens the Advanced Audio Settings menu] 59

Audio Setup S[Opens the Audio Setup menu] 47

CC (Closed Caption) Selector S[Launches the temporary CC Selector] 46

Base CC Mode SOFF/CC1/CC2/CC3/CC4/T1/T2/T3/T4 45

Digital CC Settings S[Opens the Digital CC Setup menu] 45

Input Labeling S[Opens the Input Labeling menu] 37

Channel Labeling S[Opens the Channel Labeling menu] 33

Menu Language SEnglish/French/Spanish 31

Channel Browser Setup S[Opens the Channel Browser Setup menu] 38

Enable Rating Blocking SOff/On 50

Edit Rating Limits S[Opens the Edit Rating Limits menu] 50

Channels Block S[Opens the Channels block menu] 51

Input Lock SOff/Video/Video+ 52

Front Panel Lock SOff/On 53

New PIN Code S[Opens the New PIN Code entry screen] 49

Installation S[Opens the Installation menu] 31

Sleep Timer S[Opens the Sleep Timer menu] 54

PC Settings S[Opens the PC Settings menu] 53

Power-On Mode SPower-Saving/Fast 35

Video

Audio

Preferences

Locks

Setup

50HM67_EN.book Page 29 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 4: Menu layout and navigation

Setup/Installation menu layout

The Installation menu contains the Terrestrial and System Status menus.

To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu,

select Installation, and press T.

Icon Item Option Page

Press Y,

open the

Setup menu,

and then

open the

Installation

sub-menu.

Input Configuration S[Opens the Input Configuration menu] 31

Channel Program S[Start] S [Scans for new channels on ANT] 32

Channel Add/Delete S[Opens the Channel Add/Delete menu] 32

Signal Meter S[Opens the Signal Meter menu] 35

System Information S[Opens the System Information screen] 36

Terrestrial

System Status

Navigating the menu system

You can use the buttons on the remote control or TV control

panel to access and navigate your TV’s on-screen menu

system.

•Press Y to open the menu system.

•When a menu is open, use the up/down/left/right arrow

buttons (BbC c) on the remote control or TV control panel

to move in the corresponding direction in the menu.

•Press T to save your menu settings or select a highlighted

item. (A highlighted menu item appears in a different color

in the menu.)

•All menus close automatically if you do not make a selection

within 60 seconds, except the signal meter menu, which

closes automatically after about 5 minutes.

•To close a menu instantly, press O.

Note:

•The menu background may sometimes appear black,

depending on the signal the TV is receiving. This is not a

sign of malfunction.

•The Video sub-menu appears with a black background,

which looks different from other menus.

CH RTNENTER

EXIT

Navigate Select Back Exit

Mode Sports

Off

Picture Settings

Noise Reduction

Game Mode

Theater Settings

Video

Done

Picture Settings

Contrast 100

Brightness

Reset

Mode: Sports

Color

Tint

Advanced Picture Settings

50Sharpness

50HM67_EN.book Page 30 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

Selecting the menu language

You can choose from three different languages (English,

French and Spanish) for the on-screen display of menus and

messages.

To select the menu language:

1Press Y and open the Preferences menu.

2Highlight Menu Language and press c.

3Press B or b to select your preferred menu language and

press T.

4Press O to close the Preferences menu.

Configuring the antenna input

source for the ANT terminal

To configure the ANT input source:

1Press Y and open the Setup menu.

2Highlight Installation and press T.

3(A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight

Input Configuration, and press T.

4Press C or c to select the input source (Cable or

Antenna) for the ANT input on the TV.

5To save your new settings, highlight Done and press T.

To revert to your original settings, highlight Cancel and

press T.

English

Français

Español

Input Labeling

Menu Language

Channel Browser Setup

Channel Labeling

CC Selector

English

Digital CC Settings

Preferences

Off

Base CC Mode

Installation

Sleep Timer

PC Settings

Power-On Mode Fast

Setup

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Input Configuration

Antenna In Cable

Cancel Done

50HM67_EN.book Page 31 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

Programming channels into the

TV’s channel memory

When you press < or , on the remote control or TV control

panel, your TV will stop only on the channels you programmed

into the TV’s channel memory.

Follow the steps below to program channels into the TV’s

channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your

area and store them in its memory. After the channels are

programmed automatically, you can manually add or erase

individual channels in the channel memory.

Note:

•You must configure the antenna input source before

programming channels (-page 31).

•If the Antenna input signal type is set to Cable, the automatic

channel programming process erases channels that were

previously programmed into the TV’s memory.

•If the Antenna input signal type is set to Antenna, the

automatic channel programming process adds newly found

channels to the existing set of programmed channels (and

does NOT erase channels that were previously

programmed into the TV’s memory.) To remove an Antenna

source channel from the memory, you must manually delete

it.

•To tune the TV to a channel not programmed in the channel

memory, you must use the Channel Number buttons on the

remote control.

•Programming channels when the antenna input is

configured for Cable will take substantially longer than when

the antenna input is configured for Antenna. This is normal;

however, once channel programming is finished, you should

not have to repeat the programming process again unless

your Cable TV service lineup changes significantly.

To program channels automatically:

1Configure the antenna input source, if you have not

already done so (-page 31).

2Press Y and open the Setup menu.

3Highlight Installation and press T.

4(A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight

Channel Program to bring up the Start, and press T

again to begin channel programming.

The TV will automatically cycle through all the antenna

channels, and store all active channels in the channel

memory. While the TV is cycling through the channels,

the message “Scanning channels, please wait” appears (as

shown above).

5To cancel channel programming, press O on the remote

control (or highlight Abort in the on-screen display and

press T).

When channel programming is finished, press <or , to

view the programmed channels.

Manually adding and deleting channels

in the channel memory

After automatically programming channels into the channel

memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1Press Y and open the Setup menu.

2Highlight Installation and press T.

3(A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight

Channel Add/Delete, and then press T.

Installation

Sleep Timer

PC Settings

Setup

Power-On Mode Fast

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Start

ANT Cable

Scanning channels, please wait ...

Number of Channels Found - 73

Scanning Digital Channels

Found Channel - 118

Abort

52%

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

50HM67_EN.book Page 32 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you

want to add, and then press T to check the box.

To manually add digital subchannels on a physical

channel:

Use the Channel Numbers and the Dash (=) on the remote

control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and

the box will be checked.

If the channel is not found, a message will appear.

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you

want to remove, and then press T to uncheck the box.

To save your new settings:

Highlight Done and press T.

To revert to your original settings:

Highlight Cancel and press T before saving.

To remove all channels from the channel memory:

Highlight Reset and press T, and then highlight Done and

press T.

To remove encrypted channels from the channel

memory:

If an encrypted channel is accidentally added to the channel list

by programming channels, you can remove the unwanted

encrypted (non-viewable) channel while you are channel

surfing. When you tune to an encrypted channel, the following

message will appear.

Press “1” button while the message is on the screen to

remove the unnecessary channel from the channel list.

Labeling channels

A list of common channel labels (logos) for various channels

(ABC, CBS, etc.) will be programmed into the TV. You will

be able to view and assign these logos from the Channel

Labeling window. If the desired channel label is not provided

in the list, you will be able to manually enter/edit labels using

the software keyboard.

To assign channel labels:

1Press Y and open the Preferences menu.

2Highlight Channel Labeling and press T.

The Channel Labeling window opens.

3Press < or , to select the channel you want to label.

4Press BbC c to highlight the desired channel label and

press T.

5Repeat steps 3 and 4 for other channels.

6To save your settings, highlight Done and press T.

The maximum number of labels that can be stored is 128.

To remove channel labels:

1Open the Channel Labeling window.

2Press < or , to select the channel for which you want to

remove the label.

Channel Add/Delete

2Analog

Reset

Cancel

Done

Digital

Analog

Digital

Analog

Digital

Analog

2 - 1

2 - 2

7 - 1

Digital Channel Is Encrypted - Press 1 on remote to remove channel

Input Labeling

Menu Language

Channel Browser Setup

Channel Labeling

CC Selector

English

Digital CC Settings

Off

Base CC Mode

Off

CC1

CC2

CC3

CC4

Preferences

AMAXW

AMC

ANIMAL

Custom

Clear All

Done

AMAX

ABCHD

ABCFAM

ABC

{No Label}

Press CH UP/DOWN to

change channels.

Channel Labeling

A&E

ANT

AMAXW

AMC

ANIMAL

Custom

Clear All

Done

AMAX

ABCHD

ABCFAM

ABC

{No Label}

Press CH UP/DOWN to

change channels.

Channel Labeling

A&E

ANT

(continued)

50HM67_EN.book Page 33 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

3Press BbC c to highlight No Label and press T.

4Repeat steps 2 and 3 for other channels.

5To save your settings, highlight Done and press T.

If the desired channel label is not available from the list of

presets, you can create a custom label.

To create and assign a custom label:

1Open the Channel Labeling window.

2Press < or , to select a channel you want to label.

3Press Bb c to highlight Custom and press T.

The software keyboard will appear.

4Repeatedly press the corresponding key on the remote

control to highlight the desired character on the on-screen

software keyboard.

5The highlighted character is entered after you either press

a different key, press c key, or after a two-second pause.

6Repeat steps 4 and 5 until you have entered all desired

text.

7When finished, press T.

8(New labels will be added to the list in alphabetical order

and marked with an icon to indicate that they are

custom.) Highlight the new custom label and press T to

assign. Assigned channel labels will be displayed in the

banner, Channel Add/Delete window, and Channels

Block window.

To delete the custom label:

1Open the Channel Labeling window.

2Highlight the label to be deleted and press =.

3Highlight Yes from the deletion confirmation window

and press T.

4Highlight Done and press T to save changes, and go

back to the Channel Labeling window.

Setting the HDMI™ audio mode

To set the HDMI audio mode:

1Press Y and open the Audio menu.

2Highlight Audio Setup and press T.

3Press B or b to select HDMI 1 Audio and then press

C or c to select the HDMI 1 audio mode (Auto, Digital,

or Analog). (Auto is the recommended mode.) See

“Connecting an HDMI or DVI device to the HDMI input”

(-page 19).

Note: Because the PC and HDMI-1 inputs share the same set

of analog audio inputs, the PC Audio menu setting influences

the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the

HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to

“Yes,” the HDMI 1 Audio setting is set to “Digital” and is

grayed out in the menu. (Also see item 3 on page 12 and

“Setting the PC Audio” on page 54.)

AMAXW

AMC

ANIMAL

Custom

Clear All

Done

AMAX

ABCHD

ABCFAM

ABC

{No Label}

Press CH UP/DOWN to

change channels.

Channel Labeling

A&E

ANT

AMAXW

AMC

ANIMAL

Clear All

Done

AMAX

ABCHD

ABCFAM

ABC

{No Label}

Press CH UP/DOWN to

change channels.

Channel Labeling

A&E

ANT

CH RTN

Edit

Cancel

Send

EXIT

Exit

100

Backspace

1 A B C a b c 2

J K L j k l 5

T U V t u v 8

P Q R S p q r s 7

G H I g h i 4

Space

W X Y Z w x y z 9

M N O m n o 6

INPUT

D E F d e f 3

TNT

TNTHD

TOCDEFG

Custom

Clear All

Done

TMCw

TMCXw

TMCX

TMC

TIMES

Press CH UP/DOWN to

change channels.

Channel Labeling

TLC

ANT

Delete the selected custom label?

YesNo

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

50HM67_EN.book Page 34 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

Setting the Power-On Mode feature

You can select either Power-Saving or Fast mode.

If you select Power-Saving mode and you turn off the TV, it

can take several seconds for the picture to appear when you turn

on the TV again. Power-Saving mode saves more power than

Fast mode. See “Specifications” on page 66 for details.

If you select Fast mode and the TV is turned off, the TV will

stay in Standby mode for several minutes (see Note below). If

the TV is turned on from Standby mode, the full picture

appears immediately.

To set the Power-On Mode feature:

1Press Y and open the Setup menu.

2Highlight Power-On Mode and press c.

3Press b or B to select either Fast or Power-Saving and

press T.

Note: If Power-On Mode is set to Fast and you turn off the TV,

the following will occur for a few minutes:

•The screen (lamp) lights dimly; and

•The fans continue to run.

This is a function of the Power-On Fast Shutdown mode and is

not a TV malfunction. If you do not prefer this, set the Power-

On Mode feature to Power-Saving.

When the Power-On Mode feature is set to Power-Saving, if

you repeatedly turn the TV on and off in a short period of time,

the useful service life of the lamp may be shorter than the

average useful service life (- page 63).

Viewing the digital signal meter

You can view the digital signal meter in the ANT digital TV

input source only.

To view the digital signal meter:

1Press Y and open the Setup menu.

2Highlight Installation and press T.

3A new set of Installation menu icons will appear, as shown

below. Open the Terrestrial menu, highlight Signal

Meter, and press T.

4Press BbC c to select the antenna input and digital

channel whose signal you want to check.

Note: The physical digital channel number listed in the

Signal Meter screen may not correspond to a virtual TV

channel number. Contact your local broadcasters to

obtain the RF channel numbers for your local digital

stations.

To close the screen and return to the Terrestrial

menu:

Highlight Done and press T.

To return to normal viewing:

Press O.

IMPORTANT NOTICE ABOUT HOT LAMP RESTART

When the TV has been powered on long enough for the

lamp unit to get hot, it may take several minutes for the

picture to appear in the following situations:

•When the Power-On Mode feature is set to Power-

Saving and you turn the TV off and then on again within

a few minutes; or

•If the TV is on when a short-term power failure, power

surge, or other similar power failure occurs, such that

the TV loses and regains power within a few minutes.

This is a property of DLP® TV lamp technology and is

NOT a sign of malfunction.

If this occurs, the yellow LED on the TV front panel will

blink (and the blue LED will be lit solid) until the TV is

finished restarting the lamp and the normal picture

appears. If both LEDs are blinking, you will need to turn

the TV off and then on again to restart the lamp.

Installation

Sleep Timer

PC Settings

Setup

Power-On Mode Fast Power-Saving

Fast

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Physical Digital Channel 4

Virtual Digital Channel

DoneAdvanced

4-1

Signal Locked

Peak

50HM67_EN.book Page 35 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 5: Setting up your TV

Viewing the system status

To view the system status:

1Press Y and open the Setup menu.

2Highlight Installation and press T.

3A new set of Installation menu icons will appear, as shown

below. Open the System Status menu, highlight

System Information, and press T.

4Press C c to scroll through the menu bar to select the

Software Version and view the related information.

To close the screen and return to the Installation

menu:

Highlight Done and press T.

To return to normal viewing:

Press O.

Reset Factory Defaults

To reset all settings and channels to their factory

default values:

1Press Y and open the Setup menu.

2Highlight Installation and press T. A new set of

Installation menu icons will appear.

3Open the System Status menu, highlight System

Information, and press T.

4Press C c to scroll through the menu bar to select

Factory Defaults.

5Enter your PIN code (or 0000 if no PIN code has been set).

6Highlight Yes and press T. The TV will turn off

automatically after a few seconds. After the TV turns off,

unplug the TV power cord and then plug it in again to

complete the reset process.

To cancel the reset:

Highlight No and press T.

System Information

System Status

Installation

System Information

Done

3.2.21.0

Nov 17 2006 - 01:52:20

HM07

FW: 0B

Software Version

System Information

Done

This window provides the ability to reset the TV

settings.Type in your PIN now (or "0000" if no

PIN has been set) to restore settings to their

factory default values.

Factory Defaults

System Information

Press YES to confirm. After the TV

turns off, unplug it and plug it back

in to complete the reset.

YesNo

50HM67_EN.book Page 36 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Selecting the video input source

to view

To select the video input source to view:

1Press + on the remote control or TV control panel.

2And then either:

a) Press 0–8; or

b) Repeatedly press Bb on the remote control and then

press T to change the input; or

c) Repeatedly press + on the remote control or TV

control panel to change the input.

The current signal source displays in the top right corner

of the Input Selection screen.

Note:

•You can label the video input sources according to the

specific devices you have connected to the TV

(- “Labeling the video input sources” at right).

•Sources can also be “hidden” (- “Labeling the video input

sources” at right).

•“No Video Signal” will appear randomly on the screen if no

signal is received in video input mode.

Labeling the video input sources

You can label each video input source according to the type of

device you connected to each source, from the following preset

list of labels:

•– – (default label)

•Audio Receiver

•Cable

•Compact Disc

•DTV

•DVD

•Game Console

•HD DVD

•Laser Disk

•Satellite/DSS

•VCR

•Video Recorder

•

Hide (to hide an unused input in the

Input Selection

screen)

Note: If you select PC in the Input Selection screen, you can

choose only “– –” or “Hide” as the label.

To label the video input sources:

1Press Y and open the Preferences menu.

2Highlight Input Labeling and press T.

3Press B or b to highlight the video source you want to

label.

INPUT

Input Selection ANT

ANT ANT

Video 2

ColorStream HD1

ColorStream HD2

HDMI 3

- / to Select

Video 1

HDMI 1

HDMI 2

Navigate

Input Labeling

Menu Language

Channel Browser Setup

Channel Labeling

CC Selector

English

Digital CC Settings

Off

Base CC Mode

Off

CC1

CC2

CC3

CC4

Preferences

Done

Input Labeling

Video 1 VCR

Video 2 Cable

ColorStream HD 1 Video Recorder

ColorStream HD 2 Hide

HDMI 3 DVD

HDMI 1 DTV

Satellite/DSS

HDMI 2

Reset

(continued)

50HM67_EN.book Page 37 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

4Press C or c to select the desired label for that input

source. If a particular input is not used, you can select

Hide as the label, which will cause that input to be

“grayed out” in the Input Selection screen and skipped

over when you press + on the remote control.

5To save the new input labels, highlight Done and

press T.

To revert to the factory default labels, highlight Reset

and press T.

Input labeling example:

The screen below left shows the default Input Selection

screen (with none of the inputs labeled as a specific device).

The screen below right is an example of how you could label

the inputs if you connected a VCR to VIDEO 1, Cable TV to

VIDEO 2, a video recorder to ColorStream HD1, a DTV set-

top box to HDMI 1, a satellite/DSS set-top box to HDMI 2, and

a DVD player to HDMI 3. Also note that the ColorStream HD2

input is labeled “Hidden,” which means that input will be

skipped over when + is pressed.

To clear the input labels:

1Press Y and open the Preferences menu.

2Highlight Input Labeling and press T.

3Highlight Reset and press T.

Tuning channels

Tuning channels using the

Channel Browser™

The Channel Browser™ provides an easy navigation interface

for all your channels and inputs. This feature allows you to:

•Navigate the contents of all of your inputs.

•Keep a list of your favorite channels (see “Favorites

Browser,” below).

•Keep a history of the last 32 channels or inputs viewed.

•Quickly surf and tune your recently viewed channels/inputs

from the Channel Browser™ History List (illustrated on the

next page).

•Surf via Browse mode (to immediately tune channels as you

highlight them in the Channel Browser™) or Select mode (to

surf over channels in the Channel Browser™ before you

select one to tune).

•Quickly change inputs from the Inputs List.

Favorites Browser

The Favorites Browser allows you to quickly set up a favorite

channels/inputs list that is integrated into the Channel Browser

™

To add a favorite channel/input:

1Tune to the channel or input.

2Press and hold n for 3 seconds.

Note: Additions are added to the beginning of the Favorites list

on the left side of the Channel Browser™.

To delete a favorite channel/input:

1Press n to open the Favorites browser list.

2Highlight the channel or input to delete by pressing

3 C or # c.

3Press and hold = for 3 seconds. The channel/input will

be removed from the Favorites list.

To set up the Channel Browser™:

1Press Y and open the Preferences menu.

2Highlight Channel Browser Setup and press T.

3Press B to highlight Navigation, and then press C or c

to select either Browse Mode or Select Mode.

Input Selection ANT

ANT ANT

Video 2

ColorStream HD1

ColorStream HD2

HDMI 3

Video 1

HDMI 1

HDMI 2

Input Selection ANT

ANT ANT

Cable

Video Recorder

ColorStream HD2 (Hidden)

DVD

VCR

DTV

Satellite/DSS

INPUT

to Select

Navigate

INPUT

to Select

Navigate

Input Selection screen with

no inputs labeled.

Input Selection screen with

all inputs labeled except input 4,

which has been hidden.

Done

Channel Browser Setup

Navigation

History List

Favorites List On

Inputs List On

ANT List On

Reset

Select Mode

Power Off Clear (On)

50HM67_EN.book Page 38 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

4Press b to highlight History List, and then press C or c

to select the setting you prefer: either Power Off Clear

(On), On, or Off.

Note: When History List is set to On, the channels and

inputs stored in the list will be saved every power on/off

cycle. When History List is set to Power Off Clear (On),

the channels and inputs stored in the list will be cleared

with every power on/off cycle of the TV.

5Press b to highlight ANT List, and then press C or c to

select On or Off.

6Press b to highlight Inputs List, and then press C or c

to select On or Off.

7Press b to highlight Favorites List, then press C or c to

select On or Off.

8To save your entries, highlight Done and press T.

To return to factory defaults, highlight Reset and

press T.

To open the Channel Browser™:

•Press 3 C or # c on the remote control.

•Press 3 C to surf backward through the previously tuned 32

channels in the History list, the channels in the ANT channel

list, the inputs in the Inputs list, or the favorite channels/

inputs in Favorites list.

•Press # c to surf forward through the channel History, the

ANT channel list, the Inputs list, or the favorite channels/

inputs in Favorites list.

Elements of the Channel Browser™

1Current list (History, ANT, Inputs, or Favorites)

2Input type

3Channel or input currently being viewed

4Channel or input that is currently highlighted in the

browser

5Channels stored in the History List

6Channel labels

To toggle among the available lists:

After opening the Channel Browser™, press B or b to toggle

among History, ANT, Inputs, and Favorites.

Note:

•The Channel Browser™ opens in History List by default.

Once another list has been selected, the Channel Browser™

will open in the last selected list.

•If all lists are turned off, pressing 3 C, # c, or n will

not display the Channel Browser™. If Favorites List is

turned off, n will have no effect.

•Pressing n will bring up the Channel Browser™

Favorites list regardless of the last selected list in the

Channel Browser™.

To tune to a channel or input in Browse mode:

1While watching TV, press 3 C or # c to open the

Channel Browser™ and surf back to a previous item or

surf forward to the next item in the list.

In Browse mode, when you stop on an item in the

Channel Browser™, it will be highlighted and the TV will

automatically tune to the channel or input.

2Press O to close the Channel Browser™.

Note: The Channel Browser™ will close automatically if

you do not make a selection within 30 seconds.

To tune to a channel or input in Select mode:

1While watching TV, press 3 C or # c to open the

Channel Browser™ and surf back to a previous item or

forward to the next item in the list.

In Select mode, when you stop on an item in the Channel

Browser™, it will be highlighted but you must press T to

tune the TV to the highlighted item.

2Press T to tune the TV to the highlighted item.

3Press O to close the Channel Browser™.

Adding and clearing channels and inputs in the

History List

Adding channels and inputs to the History List:

As a channel or input is tuned, the Channel Browser™ adds it

to the History List and displays it on the “right side” of the

Channel Browser™. Previously tuned channels/inputs are

“shifted” to the left, eventually moving off the left side. Press

3 C to surf backward through the previously tuned channels/

inputs. Any channel or input that is tuned repeatedly will not

be repeated in the History List, but instead is moved to the end

of the list on the right side of the Channel Browser™.

The Channel Browser™ will store the following channels:

•All channels that are tuned using the numeric buttons on the

remote control.

•All channels that are tuned using < or , on the remote

control.

Note: Whenever an item is selected that cannot be tuned (for

various reasons), the TV will automatically tune to the

previously viewed channel or input.

History

10 32 11 8

TVLAND ABCHD WEATHER

1 2 43

(continued)

50HM67_EN.book Page 39 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Clearing channels from the History List:

•Reconfiguring the ANT input will clear the History List.

Note: See page 31 for details on configuring the antenna

input.

•Once 32 channels or inputs are stored in the History List, the

oldest item will be removed from the list when a new

channel or input is tuned.

•If History List in the Channel Browser Setup is set to

“Power Off Clear (On),” turning off the TV will clear the

History List.

Tuning to the next programmed channel

To tune to the next programmed channel:

Press < or , on the remote control or TV control panel.

Note:This feature will not work unless you program channels

into the TV’s channel memory (-page 32).

Tuning to a specific channel (programmed

or unprogrammed)

Tuning analog channels:

Press the Channel Number (0–9) on the remote control. For

example, to select channel 125, press 1, 2, 5.

Tuning digital channels:

Press the Channel Number (0–9) on the remote control,

followed by the dash (=) button and then the sub-channel

number. For example, to select digital channel 125-1, press 1,

2, 5, –, 1.

Note: If a digital channel is not programmed—either through

the automatic channel scan (-page 32) or the channel add/

delete function (-page 32)—you will have to tune the RF

channel using the Channel Number and dash (=) on the

remote control.

Switching between two channels using

Channel Return

The Channel Return feature allows you to switch between two

channels without entering an actual channel number each time.

1Select the first channel you want to view.

2Select a second channel using the Channel Number

buttons (and the dash (=) button if selecting a digital

channel).

3Press R on the remote control. The previous channel

will display. Each time you press R, the TV will switch

back and forth between the last two channels that were

tuned.

Note: If you press R from a non-antenna input, the TV

will return to the last-viewed input.

Switching between two channels using

SurfLock™

The SurfLock™ feature temporarily “memorizes” one channel

to the R button, so you can return to that channel quickly

from any other channel by pressing R. To memorize a

channel to the R button:

1Tune the TV to the channel you want to program into the

R button.

2Press and hold R for about 2 seconds until the message

“Channel Memorized” appears on-screen. The channel

has been programmed to the R button.

3You can then change channels repeatedly, and when you

press R, the memorized channel will be tuned.

The TV will return to the memorized channel one time only.

Once you press R and then change channels again, the CH

RTN memory will be cleared and the button will function as

Channel Return, by switching back and forth between the last

two channels that are tuned. This feature also works for

external inputs.

50HM67_EN.book Page 40 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Selecting the picture size

You can view many program formats in a variety of picture

sizes—Natural, TheaterWide 1, TheaterWide 2,

TheaterWide 3, Full, and 4:3 HD.

Note: The “picture size” illustrations are examples only. The

format of the image (in any of the picture sizes) will vary

depending on the format of the signal you are currently

watching. Select the picture size that displays the current

program the way that looks best to you.

You can save separate picture size preferences for each input

on your TV.

To select the picture size using the remote control:

1Press I on the remote control.

2While the Picture Size screen is open, you can do one of

the following to select the desired picture size:

•Repeatedly press I.

•Press the corresponding Number button (0–5) while the

Picture Size screen is open.

•Press B or b while the Picture Size screen is open.

To select the picture size using the menus:

1Select Picture Size in the Theater Settings menu.

2Press C or c to select the desired picture size setting.

3Highlight Done and press T.

Note: Some of the picture sizes may not be available

depending on the receiving signal format (those will be

“grayed out” in the Picture Size screen).

Note: If you select one of the TheaterWide® picture sizes, the

top and bottom edges of the picture (including subtitles or

captions) may be hidden. To view the hidden edges, either

scroll the picture (TheaterWide 2 and 3 only) or try viewing the

program in Full or Natural picture size.

Natural picture size

•The image is displayed close to its originally formatted

proportion. Some program formats will display with

sidebars and/or bars at the top and bottom.

TheaterWide 1 picture size (for 4:3 format programs)

•The center of the picture remains close to its original

proportion, but the left and right edges are stretched wider to

fill the screen.

TheaterWide 2 picture size (for letter box programs)

•The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

•The top and bottom edges of the picture may be hidden. To

view the hidden areas, see “Scrolling the TheaterWide®

picture” (-page 42).

Using these functions to change the picture size (i.e.,

changing the height/ width ratio) for any purpose other than

your private viewing may be prohibited under the Copyright

Laws of the United States and other countries, and may

subject you to civil and criminal liability.

PIC SIZE

Picture Size

Natural

TheaterWide 1

TheaterWide 2

TheaterWide 3

Full

4:3 HD

- / to Select

Done

Theater Settings

Mode: Sports

Picture Size Full

Picture Scroll

Cinema Mode Film

Auto Aspect Ratio On

Reset

Natural picture size example

TheaterWide 1 picture size example

A B C D E F G - - - - - - - - - - - - - - - -

TheaterWide 2 picture size example

50HM67_EN.book Page 41 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

TheaterWide 3 picture size (for letter box programs

with subtitles)

•The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

•The top and bottom edges are hidden. To view the hidden

areas (such as subtitles or captions), see “Scrolling the

TheaterWide® picture.”

Full picture size (for 16:9 [480i, 480p] source

programs only)

•If receiving a squeezed 4:3 format program, the picture is

stretched wider to fill the width of the screen, but not

stretched taller.

•None of the picture is hidden.

4:3 HD picture size (for 720p, 1080i, and 1080p

program sources only)

•Sidebars fill the empty vertical spaces.

•Picture is not distorted from original size.

Scrolling the TheaterWide® picture

(TheaterWide 2 and 3 only)

You can set separate scroll settings for the TheaterWide 2 and

TheaterWide 3 modes for each input.

To set the scroll settings:

1Press Y and open the Video menu.

2Highlight Theater Settings and press T.

3In the Picture Size field, select either TheaterWide 2

or TheaterWide 3 (you cannot scroll in any other mode).

4Press b to highlight the Picture Scroll field.

5Press C or c to scroll the picture up and down as needed,

from –10 to +20.

6To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

A B C D E F G - - - - - - - - - - - - - - - -

A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -

TheaterWide 3 picture size example

Full picture size example

4:3 HD picture size example

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Mode: Sports

DoneReset

Theater Settings

Picture Size TheaterWide 2

Picture Scroll -5

Cinema Mode Film

Auto Aspect Ratio On

50HM67_EN.book Page 42 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Using the auto aspect ratio feature

When the auto aspect ratio feature is set to On, the TV will

automatically select the picture size when one of the following

input sources is received:

•A 480i signal from the VIDEO 1, VIDEO 2, ColorStream

HD-1, or ColorStream HD-2 input.

•A 480i, 480p, 720p, 1080i, 1080p, or VGA signal from the

HDMI input.

Note: The auto aspect ratio feature is not applicable to

antenna or cable input sources.

To turn on the auto aspect ratio feature:

1Press Y and open the Video menu.

2Highlight Theater Settings and press T.

3In the Auto Aspect Ratio field, select On.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

To turn off the auto aspect ratio feature:

Select Off in step 3 above.

Selecting the cinema mode

(480i and 1080i signals)

When you view a DVD (3:2 pulldown processed) from a DVD

player connected to the VIDEO 1, VIDEO 2, ColorStream

HD-1, ColorStream HD-2 (component video), or HDMI

inputs on the TV, smoother motion can be obtained by setting

the Cinema Mode to Film.

To set the Cinema Mode to Film:

1Press Y and open the Video menu.

2Highlight Theater Settings and press T.

3In the Cinema Mode field, select Film.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

To set the Cinema Mode to Video:

Select Video in step 3 above.

Aspect ratio of

signal source

Automatic aspect size (automatically

selected when Auto Aspect is On)

4:3 normal Natural (with sidebars)

4:3 letter box TheaterWide 2

16:9 full Full

Not defined

(no ID-1 data

or HDMI

aspect data)

The current picture size you set under

“Selecting the picture size” on page 41.

Theater Settings

Picture Size Natural

Picture Scroll --

Cinema Mode Film

Auto Aspect Ratio On

DoneReset

Mode: Sports

Theater Settings

Picture Size Natural

Picture Scroll --

Cinema Mode Film

Auto Aspect Ratio On

DoneReset

Mode: Sports

50HM67_EN.book Page 43 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Adjusting the picture

Selecting the picture mode

You can select your desired picture settings from four different

modes, as described below.

To select the picture mode:

Press u on the remote control.

The following popup menu appears on-screen.

Press B or b to select the picture mode you prefer and

press T.

To select the picture mode using the menu system:

1Press Y and open the Video menu.

2Highlight Mode and press T.

3Press B or b to select the picture mode you prefer and

press T.

Note: The picture mode you select affects the current

input only. You can select a different picture mode for

each input.

Adjusting the picture quality

You can adjust the picture quality (Contrast, Brightness, Color,

Tint, and Sharpness) to your personal preferences.

To adjust the picture quality:

1Press Y and open the Video menu.

2Highlight Picture Settings and press T.

3Press B or b to select the picture quality you want to

adjust (Contrast, Brightness, Color, Tint, or

Sharpness), and then press C or c to adjust the setting,

as described in the table above.

4To save the new settings, highlight Done and press T.

You can use any of the picture modes (- “Selecting the

picture mode,” above left) as a starting point for adjusting

the picture settings.

To revert back to the base mode that you began adjusting

the picture settings from, highlight Reset and press T.

The picture qualities you adjusted are automatically saved in

the Preference mode (- “Selecting the picture mode,”

above left) until Reset is selected.

Mode Picture Quality

Sports Bright and dynamic picture (factory setting)

Standard Standard picture settings (factory setting)

Movie Lower contrast for darkened room (factory

setting)

Preference Your personal preferences

Sports

Standard

Movie

Preference

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Standard

Movie

Preference

Selection Pressing C Pressing c

Contrast lower higher

Brightness darker lighter

Color paler deeper

Tint reddish greenish

Sharpness softer sharper

Done

Picture Settings

Contrast 100

Brightness

Reset

Mode: Sports

Color

Tint

Advanced Picture Settings

50Sharpness

Picture Settings Mode: Preference

Contrast 70

50HM67_EN.book Page 44 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Using the closed caption mode

Base closed captions

The closed caption mode has two options:

•Captions—An on-screen display of the dialogue, narration,

and sound effects of TV programs and videos that are closed

captioned (usually marked “CC” in program guides).

•Text—An on-screen display of information not related to

the current program, such as weather or stock data (when

provided by individual stations).

To view captions or text:

1Press Y and open the Preferences menu.

2Highlight Base CC Mode and press c.

3Press B or b to select the desired closed caption mode and

press T.

•To view captions:

Highlight CC1, CC2, CC3, or CC4. (CC1 displays

translation of the primary language in your area.)

Note: If the program or video you selected is not closed

captioned, no captions will display on-screen.

•To view text:

Highlight T1, T2, T3, or T4.

Note: If text is not available in your area, a black rectangle

may appear on screen. If this happens, set the Base CC

Mode to Off.

•To turn off the closed caption mode:

Select Off in step 3 above.

Note: A closed caption signal may not display in the following

situations:

•When a videotape has been dubbed

•When the signal reception is weak

•When the signal reception is non-standard

Digital CC Settings

You can customize the closed caption display characteristics

by changing the background color, text size, type, edge, and

color.

Note:

•This feature is available for digital channels only.

•You cannot set the Caption Text and Background as the

same color.

To customize the closed captions:

1Press Y and open the Preferences menu.

2Highlight Digital CC Settings and press T.

3Press B or b to highlight the characteristic you want to

change, and then press C or c to select the format for that

characteristic (see table below).

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Input Labeling

Menu Language

Channel Browser Setup

Channel Labeling

CC Selector

English

Digital CC Settings

Off

Base CC Mode

Off

CC1

CC2

CC3

CC4

Preferences

Giant pandas eat leaves.

WORLD WEATHER

Temps Current

F C Weather

LONDON 51 11

MOSCOW

PARIS

ROME

TOKYO

57 14

53 12

66 19

65 18

Cloudy

Clear

Cloudy

Rain

Clear

Caption Size Auto, Small, Standard, Large

Caption Text

Type

Auto, Default, Mono w. Serif, Prop. w. Serif,

Mono w/o Serif, Prop. w/o Serif, Casual,

Cursive, Small Capitals

Caption Text

Edge

Auto, None, Raised, Depressed, Uniform,

Left Drop Shadow, Right Drop shadow

Caption Text

Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

Background

Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

Caption Text

Edge Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

Done

Digital CC Settings

Caption Size Auto

AutoCaption Text Type

Caption Text Edge Color

Reset

Auto

ABC123

Caption Text Edge

Caption Text Color

Background Color

Auto

Preview

window

50HM67_EN.book Page 45 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

CC Selector

You can use the CC Selector to temporarily override the

default analog caption mode (set in Base CC Mode) for a

particular channel. However, once you change to another

analog channel, the closed caption setting will automatically

change back to the current Base CC Mode setting.

You can also use the CC Selector to select digital closed

caption services (if available). When such services are not

available, the CC Selector presents a default list of services.

If the selected service is not available, the next best service will

be used instead.

To select closed captions:

1Press Y and open the Preferences menu.

2Highlight CC Selector and press T.

3Press B or b to select Closed Caption, and then press

C or c to select the desired service.

4Press O.

Adjusting the audio

Muting the sound

Press W to partially reduce (1/2 MUTE) or turn off (MUTE)

the sound. Each time you press W, the mute mode will change

in the following order:

If the closed caption mode is set to Off when you select

“MUTE” mode, the closed caption feature is automatically

activated. To mute the audio without automatically activating

the closed caption feature, use Z to set the volume to 0. See

“Using the closed caption mode” (-page 45) for more

information on closed caption modes.

Using the digital audio selector

You can use the Digital Audio Selector to conveniently

switch between audio tracks on a digital channel (for those

channels that have multiple audio tracks). This temporarily

overrides the audio track chosen by the language option under

Audio Setup (- “Selecting stereo/SAP broadcasts” on

page 47).

To use the digital audio selector:

1Press Y and open the Audio menu.

2Highlight Digital Audio Selector and press T.

3Press B or b to select Audio, and then press C or c to

select the desired service.

4Press O.

Input Labeling

Menu Language

Channel Browser Setup

Channel Labeling

CC Selector

English

Digital CC Settings

Off

Base CC Mode

Off

CC1

CC2

CC3

CC4

Preferences

CC 1

None

Closed Caption

Audio

Volume1/2 Mute Mute

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio

Audio Setup

CC 1Closed Caption

Audio None

50HM67_EN.book Page 46 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Selecting stereo/SAP broadcasts

The multi-channel TV sound (MTS) feature allows you to

output high-fidelity stereo sound. MTS also can transmit a

second audio program (SAP) containing a second language,

music, or other audio information (when provided by

individual stations).

When the TV receives a stereo or SAP broadcast, the word

“STEREO” or “SAP” appears on-screen when E is pressed.

The MTS feature is not available when the TV is in VIDEO

mode.

To listen to stereo sound:

1Press Y and open the Audio menu.

2Highlight Audio Setup and press T.

3In the MTS field, select Stereo.

4To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight

Reset and press T.

Note:

•You can typically leave the TV in Stereo mode because

it will automatically output the type of sound being

broadcast (stereo or monaural).

•If the stereo sound is noisy, select Mono to reduce the

noise.

To listen to an alternate language on an ATSC digital

station (if available):

Highlight the Language field in step 3 above, and then press

C or c to select the language you prefer.

To listen to a second audio program on an analog

station (if available):

Select SAP in step 3 above.

Note:

•A second audio program (SAP) can be heard only on those

TV stations that offer it. For example, a station might

broadcast another language as a second audio program. If

you have SAP on, you will see the current program on the

screen but hear the other language instead of the program’s

normal audio.

•If you have SAP on and the station you are watching is not

broadcasting a second audio program, the station’s normal

audio will be output. However, occasionally there is no

sound at all in SAP mode. If this happens, set the MTS

feature to Stereo mode.

Adjusting the audio quality

You can adjust the audio quality by adjusting the bass, treble,

and balance.

To adjust the audio quality:

1Press Y and open the Audio menu.

2Highlight Audio Settings and press T.

3Press b or B to highlight the item you want to adjust

(Bass, Treble, or Balance).

4Press C or c to adjust the level.

•C makes the bass or treble weaker or increases the

balance in the left channel (depending on the item

selected).

•c makes the bass or treble stronger or increases the

balance in the right channel (depending on the item

selected).

5To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight

Reset and press T.

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio

Audio Setup

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

Done

Audio Settings

Bass 100

Treble

Reset

100

Balance

StableSound Off

50HM67_EN.book Page 47 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Using the StableSound® feature

The StableSound® feature limits the highest volume level to

prevent extreme changes in volume when the signal source

changes (for example, to prevent the sudden increase in

volume that often happens when a TV program switches to a

commercial).

To turn on the StableSound® feature:

1Press Y and open the Audio menu.

2Highlight Audio Settings and press T.

3In the StableSound field, select On.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: The RESET function returns your audio adjustments

to the following factory settings:

Bass . . . . . . . . center (50)

Treble . . . . . . . center (50)

Balance . . . . . . center (0)

StableSound . . Off

To turn off the StableSound feature:

Select Off in step 3 above.

Selecting the optical audio output format

You can use this feature to select the optical audio output

format when you connect a Dolby Digital decoder or other

digital audio system to the Optical Audio Out terminal on

the TV (see “Connecting a digital audio system” on page 20).

To select the optical audio output format:

1Press Y and open the Audio menu.

2Highlight Audio Setup and press T.

3In the Optical Output Format field, select either

Dolby Digital or PCM, depending on your device.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Using the Dolby® Digital Dynamic Range

Control feature

This dynamic range control feature causes the ATSC dynamic

range to be further compressed, allowing you to switch from

ATSC to analog broadcasts at the same dynamic range.

To use the Dolby Digital Dynamic Range Control:

1Press Y and open the Audio menu.

2Highlight Audio Setup and press T.

3In the Dolby Digital Dynamic Range Control field,

select Compressed. When Standard is selected, the

audio is output with minimal compression.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note:

•This item will be grayed out for NTSC signals, Video,

ColorStream, and PC inputs.

•The Dolby Digital Dynamic Range Control will function in

relation to Optical Output Format (PCM mode).

Done

Audio Settings

Bass 100

Treble

Reset

100

Balance

StableSound On

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

50HM67_EN.book Page 48 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Using the Locks menu

The Locks menu includes the Enable Rating Blocking, Edit

Rating Limits, Channels Block, Input Lock, Front (control)

Panel Lock, and New PIN Code features. You can use these

features after entering the correct PIN code.

Entering the PIN code

1Press Y and highlight the Locks menu icon.

2Press b, which displays the PIN code entry screen.

•The Lock System screen (below) appears if a PIN

code has not been stored. Press the Channel Number

buttons to enter a new four-digit code, enter the code a

second time to confirm, and press T.

•The Locks/Active screen (below) appears if the PIN

code is already stored. Use the Number buttons to enter

your four-digit code and press T.

If the wrong PIN code is entered, the message “Incorrect PIN

code, please try again!” appears. Highlight Retry and press

T. Enter the code again and press T.

When the correct PIN code is entered, the Locks menu opens.

If you cannot remember your PIN code

While the PIN code entering screen is displayed, press E

four times within five seconds. The PIN code will be cleared

and you can enter a new PIN code.

Changing your PIN code

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T.

4Press b to highlight New PIN Code and press T.

5Press the Number buttons to enter a new four-digit code.

Reenter the PIN code to confirm it.

6Press T. The new PIN code is now active.

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Please enter a 4 digit PIN code

Confirm PIN code

Cancel Done

Lock System

Locks Active

Please enter the 4 digit PIN code

Cancel

****

Done

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Please enter a 4 digit PIN code

Confirm PIN code

Cancel Done

New PIN Code

****

50HM67_EN.book Page 49 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Blocking TV programs and movies

by rating (V-Chip)

Some TV programs and movies include signals that classify

the content of the program (violence, sex, dialog, language).

The V-Chip feature in this TV detects the signals and blocks

the programs according to the ratings you select. (For rating

descriptions, see the tables on the next page.)

Note: Rating blocking is a function of the V-Chip feature in this

TV, which supports the U.S. V-Chip system only.

To block and unblock TV programs and movies:

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T.

4Press b to highlight Enable Rating Blocking.

5Press c and b to select On, and then press T.

6Press b to highlight Edit Rating Limits and press T.

The Edit Rating Limits screen (below) appears.

7Press BbC c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will

be blocked. As you highlight a rating, a definition for the

rating appears at the bottom of the screen.

8When done selecting the ratings you want to block,

highlight Done and press T.

Downloading an additional rating system

for blocking TV programs and movies

In the future, an additional rating system may become

available for use in selectively blocking programs.

Note: The currently tuned station must be receiving a digital

signal before an additional rating system can be downloaded.

To download the additional rating system

(if available):

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T.

4Press b to highlight Enable Rating Blocking.

5Press c and b to select On, and press T.

6Press b to highlight Edit Rating Limits and press T.

The Edit Rating Limits screen appears.

7Highlight Alt RS and press T. The Edit Alternate

Ratings screen will appear.

Note:

•The Alt RS button will only be available if an additional

rating system is currently available.

•It may take several minutes for the TV to download the

additional rating system.

•The information displayed in the Alternate Ratings

screen will depend on the configuration of the

additional rating system available at the time of

download.

8Press B b C c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will

be blocked.

9When you are finished selecting the ratings you want to

block, highlight Done and press T.

10 In the Edit Rating Limits screen, highlight Done and

press T.

Note:

•The additional rating system can only be downloaded one

time. You will not be able to download any updates to the

rating system should such updates become available.

•The additional rating system is not designed, transmitted, or

controlled by the TV or Toshiba, nor is the availability of an

additional rating system determined or controlled by

Toshiba. Similarly, the rating of programs in an additional

rating system is not determined, transmitted, or controlled

by the TV or Toshiba.

•The additional rating system is an evolving technology;

therefore, availability, content, and format may vary.

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Edit Rating Limits

(V-CHIP)

D L S V

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

"None" Rated

Movies

Children

Youth

Cancel

Done

Alt RS

PG-13

NC-17

50HM67_EN.book Page 50 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Note:

•If you place an “5” in the box next to “ ‘None’ Rated,”

programs rated “None” will be blocked; however, programs

that do not provide any rating information will not be

blocked.

•To display the rating of the program you are watching, press

E on the remote control. If it is rated “None,” the word

“NONE” appears in the RECALL screen (as shown below

right). If rating information is not provided, no rating will

appear in the RECALL screen.

Blocking channels

With the Channels Block feature, you can block specific

channels. You will not be able to tune blocked channels unless

you unlock them.

To block channels:

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T

(-page 49).

4Press b to highlight Channels Block and then press T.

A list of the channels available for that input will be

displayed along with the call letters for each channel, if

available.

5Press Bb to highlight the channel you want to block and

press T, which puts an “5” in the box next to that

channel.

6Repeat step 5 for other channels you want to block.

7Highlight Done and press T.

To unblock individual channels:

In step 5 above, press Bb to highlight the channel you want to

unblock, press T to remove the “5” from the box, highlight

Done and press T.

Independent rating system for broadcasters

Ratings Description and Content themes

TV-MA

Mature Audience Only (This program is specifically

designed to be viewed by adults and therefore may

be unsuitable for children under 17.)

L) Crude or indecent language S) Explicit sexual

activity V) Graphic violence

TV-14

Parents Strongly Cautioned (This program contains

some material that many parents would find

unsuitable for children under 14 years of age.)

D) Intensely suggestive dialog L) Strong, coarse

language S) Intense sexual situations V) Intense

violence

TV-PG

Parental Guidance Suggested (This program

contains material parents may find unsuitable for

younger children.)

D) Some suggestive dialog L) Infrequent coarse

language S) Some sexual situations V) Moderate

violence

TV-G General Audience (Most parents would find this

program suitable for all ages.)

TV-Y7,

TV-Y7FV

Directed to Older Children (This program is designed

for children age 7 and above. Note: Programs in

which fantasy violence may be more intense or more

combative than other programs in this category are

designated TV-Y7FV.)

TV-Y All Children (This program is designed to be

appropriate for all children.)

Independent rating system for movies

Ratings Description and Content themes

XX-rated (For adults only)

NC-17 Not intended for anyone 17 and under

RRestricted (Under 17 requires accompanying parent

or adult)

PG-13 Parents Strongly Cautioned (Some material may be

inappropriate for children under 13)

PG Parental Guidance Suggested (Some material may

not be suitable for children)

GGeneral Audience (Appropriate for all ages)

TV - PG L V NONE

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Channels Block

Cancel

Done

Block All

Allow All

(continued)

50HM67_EN.book Page 51 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

To block all channels at once:

Highlight Block All in step 5 on previous page and then

highlight Done and press T.

To unblock all locked channels at once:

Highlight Allow All in step 5 on previous page and then

highlight Done and press T.

Unlocking programs temporarily

If you try to tune the TV to a program that exceeds the rating

limits you set, the TV will enter program lock mode and the

following message will appear on-screen:

You can either temporarily unlock the program or select an

unlocked program to watch.

To temporarily unlock the program:

1Press W.

2Enter your four-digit PIN code and press T. If the correct

code is entered, the program lock mode is released and the

normal picture appears. All locking is disabled until the

TV is turned off, and will be enabled when the TV is

turned on again.

Using the input lock feature

You can use the Input Lock feature to lock the video inputs

(VIDEO 1, VIDEO 2, ColorStream HD-1, ColorStream

HD-2, HDMI 1, HDMI 2, HDMI 3 and PC) and channels 3 and

4. You will not be able to view the input sources or channels

until you unlock the inputs.

To lock/unlock the video inputs:

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T.

4Press b to highlight Input Lock and press c.

5Press B or b to select the level of video input locking you

prefer, as described below.

Video: Locks VIDEO 1, VIDEO 2, ColorStream HD1/

HD2, HDMI 1, HDMI 2, HDMI 3, and PC.

Video+: Locks VIDEO 1, VIDEO 2, ColorStream HD1/

HD2, HDMI 1, HDMI 2, HDMI 3, PC and channels 3 and

•Select Video+ if you play video tapes via an ANT

input.

Off: Unlocks all video inputs and channels 3 and 4.

6Press T.

Channels Block

Cancel

Done

Block All

Allow All

This program exceeds the rating limit you set.

Push 'mute' to enter PIN.

Locks Active

Enter PIN code to temporarily unblock.

Cancel

****

Done

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Video

Video +

50HM67_EN.book Page 52 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Using the control panel lock feature

You can lock the control panel to prevent your settings from

being changed accidentally (by children, for example). When

the control panel lock is On, none of the controls on the TV

control panel will operate except POWER.

To lock the control panel:

1Press Y and highlight the Locks menu icon.

2Press b to display the PIN code entering screen.

3Enter your four-digit PIN code and press T.

4Press b to highlight Front Panel Lock.

5Press c and C or c to highlight On and press T. When

the control panel is locked and any button on the control

panel (except POWER) is pressed, the message “Not

Available” appears.

To unlock the control panel:

Highlight Off in step 5 above, or press and hold the

VOLUME – button on the TV control panel for about 10

seconds until the volume icon appears.

Using the PC settings feature

You can view an image from a PC on the TV screen.

When a PC is connected to the TV's PC IN terminal, you can

use the PC Settings feature to make adjustments to the image.

If the edges of the picture are cut off, readjust the Horizontal

Position and Vertical Position. If the picture is affected by

interference, readjust the Clock Phase and Sampling

Clock.

To adjust the PC settings:

1Repeatedly press + to select PC input mode

(- “Selecting the video input source to view” page 37).

2Press Y and open the Setup menu.

3Highlight PC Settings and press T.

Note: If a PC is not connected or there is no pc input

signal, this feature will be grayed out in the Setup menu.

4Press B or b to highlight the item you want to adjust.

5Press C or c to make the appropriate adjustments.

Note: The screen is disrupted momentarily when

adjusting the PC settings. This is not a sign of malfunction.

•Horizontal Position:

Moves the picture left/right.

The adjustment range is within ±10 from center.*

•Vertical Position:

Moves the picture up/down.

The adjustment range is within ±10 from center.*

•Clock Phase:

Helps to reduce noise and sharpen the picture.

The adjustment range is within ±4 from center.*

•Sampling Clock:

Helps to reduce noise and minimize periodic vertical stripes

on the screen.

The adjustment range is within ±5 from center.*

*The default settings may vary depending on the input signal format.

Input Lock

New PIN Code

Front Panel Lock

Enable Rating Blocking

Channels Block

Off

Edit Rating Limits

Locks

Off

Installation

Sleep Timer

PC Settings

Setup

Power-On Mode Fast

Done

PC Settings

Vertical Position

Reset

Horizontal Position 0

Clock Phase

Sampling Clock

50HM67_EN.book Page 53 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Setting the PC Audio

This function allows you to output the sound from your PC (if

connected) or mute the sound from your PC and output the

sound from your HDMI (DVI) connection. (-page 21)

To set the PC Audio:

1Press Y and open the Audio menu.

2Highlight Audio Setup and press T.

3Press B or b to select PC Audio and then press C or c

to select No or Yes.

Yes: Outputs the sound from your PC.

No: Mutes the sound from your PC, and outputs the

sound from the HDMI-1 connection.

Note: Because the PC and HDMI-1 inputs share the same

set of analog audio inputs, the PC Audio menu setting

influences the HDMI 1 Audio menu setting. If PC Audio is

set to “No,” the HDMI 1 Audio setting changes to “Auto.”

If PC Audio is set to “Yes,” the HDMI 1 Audio setting is

set to “Digital” and is grayed out in the menu. (Also see

item 3 on page 12 and “Setting the HDMI™ Audio mode”

on page 34.)

Setting the sleep timer

You can set the sleep timer to turn off the TV after a set length

of time (maximum of 180 minutes).

To set the sleep timer using the remote control:

Press [ on the remote control to set the length of time until

the TV turns off. Repeatedly press [ to increase the time in

10-minute increments, or press B or b to increase or decrease

the time in 10-minute increments, to a maximum of 180

minutes.

To set the sleep timer using the on-screen menus:

1Press Y and open the Setup menu.

2Highlight Sleep Timer and press T.

3Press the Number buttons to enter the length of time in

10-minute increments.

4Highlight Done and press T.

Note: When a power failure occurs, the sleep timer setting

may be cleared.

To display the remaining sleep time:

Press [.

Note: A message will display on-screen when there is one

minute remaining on the sleep timer.

To cancel the sleep timer:

Repeatedly press [ until it is set to 0 minute.

Done

Audio Setup

Language

Reset

MTS Stereo

English

Dolby Digital

Optical Output Format

HDMI 1 Audio

PC Audio No

Auto

Dynamic Range Control Compressed

Dolby Digital

Installation

Sleep Timer

PC Settings

Setup

Power-On Mode Fast

Sleep Timer

Enter total minutes until the TV

turns off automatically (Maximum

180 minutes)

120

Cancel Done

Sleep Timer

120 minutes

50HM67_EN.book Page 54 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 6: Using the TV’s features

Displaying TV status information

To display TV status information using RECALL:

Press E on the remote control.

The following information will display (if applicable):

•Current input (ANT, VIDEO 1, etc.)

•If ANT is the current input, either “CABLE” (for cable TV)

or “ANT” (for over-the-air broadcasts).

•Channel number (if in ANT mode)

•Channel label (if set)

•Digital signal strength indicator (bar graph in lower right

corner of box; for ATSC signal only)

•Stereo, Mono or SAP audio status (when HDMI input mode,

Dolby Digital or PCM)

•Video resolution

•Aspect ratio of incoming video signal (4:3 or 16:9)

•V-Chip rating status

•Lamp Mode ( : High Bright)

To close the RECALL screen:

Press E again.

To display TV status information using INFO:

Press Q on the remote control.

The following additional information will display for off air

digital channels (if applicable):

•Title

•Duration

•Detailed description

Note: The location of the banner can be moved to the top or

bottom of the screen by pressing B or b while the RECALL or

INFO display is on-screen. (The last position will be stored to

memory.)

Understanding the auto power off

feature

The TV will automatically turn itself off after approximately

15 minutes if it is tuned to a vacant channel or a station that

completes its broadcast for the day. This feature functions in

ANT mode only.

Understanding the last mode

memory feature

If the power is cut off while you are viewing the TV, the

Last Mode Memory feature automatically turns on the TV

when the power is resupplied.

Note: You should unplug the TV’s power cord if it is possible

that you will be away from the TV for an extended period of time

after the power is restored.

123-456

ANT

ABCHD

Stereo SAP

9:00pm .

TV-PG L V1080i

16:9

123-456

ANT

MLB Young,s XXX...

Today,s Major League Baseball.

9:00pm -11:00pm

ABCHD

Stereo SAP

TV-PG L V1080i

16:9

50HM67_EN.book Page 55 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 7: Using the TV’s advanced features

Using the advanced picture settings

features

Using dynamic contrast

When dynamic contrast is set to Low, Middle, or High, the

TV will detect changes in the picture quality that affect the

appearance of your contrast settings and then automatically

adjust the video.

To select dynamic contrast preferences:

1Press Y and open the Video menu.

2Highlight Picture Settings and press T.

3Highlight Advanced Picture Settings and press T.

4In the Dynamic Contrast field, select either Off, Low,

Middle or High.

5To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: If you select one of the factory-set picture modes

(Sports, Standard, or Movie) and then change the

dynamic contrast setting, the picture mode automatically

changes to Preference.

Using the static gamma feature

The static gamma feature allows you to adjust the levels of

black in the picture.

To adjust the static gamma settings:

1Press Y and open the Video menu.

2Highlight Picture Settings and press T.

3Highlight Advanced Picture Settings and press T.

4In the Static Gamma field, press C or c to adjust the

static gamma.

The adjustment range is within ±5 from center.

•If the setting is moved in the minus direction, the detail

of black colors will be decreased.

•If the setting is moved in the plus direction, the detail of

black colors will be increased.

5To save the new settings, highlight Done and press T.

To revert the factory defaults, highlight Reset and

press T.

Note: If you select one of the factory-set picture modes

(Sports, Standard or Movie) and then change the static

gamma setting, the picture mode automatically changes

to Preference.

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Done

Picture Settings

Contrast 100

Brightness

Reset

Mode: Sports

Color

Tint

Advanced Picture Settings

50Sharpness

Done

Advanced Picture Settings Mode: Preference

Static Gamma

Reset

Dynamic Contrast Off

Cool

Color Temperature

High Bright

Lamp Mode

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Done

Picture Settings

Contrast 100

Brightness

Reset

Mode: Sports

Color

Tint

Advanced Picture Settings

50Sharpness

Done

Advanced Picture Settings Mode: Preference

Static Gamma

Reset

Dynamic Contrast

High

Cool

Color Temperature

High Bright

Lamp Mode

50HM67_EN.book Page 56 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 7: Using the TV’s advanced features

Selecting the color temperature

You can change the quality of the picture by selecting from

three preset color temperatures (Cool, Medium, and Warm), as

described below.

To select the color temperature:

1Press Y and open the Video menu.

2Highlight Picture Settings and press T.

3Highlight Advanced Picture Settings and press T.

4In the Color Temperature field, select the mode you

prefer (Cool, Medium, or Warm).

5To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: If you select one of the factory-set picture modes

(Sports, Standard, or Movie) and then change the color

temperature mode, the picture mode automatically

changes to Preference.

Selecting the lamp mode

You can select either the High Bright or Low Power lamp

mode.

The High Bright mode is useful when additional picture

brightness is desired (such as in a bright room).

Note: The Lamp Mode field will be grayed out for a while after

the TV is turned on.

To select the lamp mode:

1Press Y and open the Video menu.

2Highlight Picture Settings and press T.

3Highlight Advanced Picture Settings and press T.

4In the Lamp Mode field, select either High Bright or

Low Power.

5To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: If you set the lamp mode to Low Power, each time

you turn on the TV, the lamp will start out in High Bright

mode but will switch to Low Power mode after a short

period of time. You may notice a change in screen

brightness when this happens. This is normal and is not a

sign of malfunction.

Mode Picture Quality

Cool blueish

Medium neutral

Warm reddish

Done

Advanced Picture Settings Mode: Preference

Static Gamma

Reset

Dynamic Contrast

High

Cool

Color Temperature

High Bright

Lamp Mode

Done

Advanced Picture Settings Mode: Preference

Static Gamma

Reset

Dynamic Contrast High

Cool

Color Temperature

High Bright

Lamp Mode

50HM67_EN.book Page 57 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 7: Using the TV’s advanced features

Using CableClear® digital noise reduction

The CableClear® digital noise reduction feature allows you to

reduce visible interference in your TV picture. This may be

useful when receiving a broadcast with a weak signal

(especially a Cable channel) or playing a noisy video cassette

or disc.

To change the CableClear settings:

1Press Y and open the Video menu.

2Highlight Noise Reduction and press T.

3In the CableClear field, select your desired setting.

Note:

•If the current input is ANT, VIDEO 1, or VIDEO 2, the

menu will display the text “CableClear.” The available

selections are Off, Auto, Low, Middle, and High.

•If the current input is ColorStream HD1, ColorStream

HD2, HDMI 1, HDMI 2, or HDMI 3 the menu will display

the text “DNR.” The available selections are Off, Auto,

Low, Middle, and High. Auto will react proportionally

to the strength of the noise. Low, Middle, and High will

reduce the noise in varying degrees, from lowest to

highest, respectively.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Using MPEG noise reduction

The MPEG noise reduction feature allows you to reduce

visible interference caused by MPEG compression. Choices

for MPEG noise reduction are Off, Low, Middle, and High.

Off is automatically selected when this feature is disabled

(“grayed out”).

To select the MPEG noise reduction level:

1Press Y and open the Video menu.

2Highlight Noise Reduction and press T.

3Press B or b to highlight the MPEG Noise Reduction

field, and then press C or c to select either Off, Low,

Middle or High.

4To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Done

Noise Reduction ANT

Reset

CableClear Auto

Low

MPEG Noise Reduction

Done

Noise Reduction ANT

Reset

CableClear Auto

Low

MPEG Noise Reduction

50HM67_EN.book Page 58 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 7: Using the TV’s advanced features

Using the Game Mode feature

You can use the Game Mode feature for shorter frame delays

when playing a video game requiring split-second timing

between the on-screen display and input from the controller

(such as music creation and high-action games).

This feature is more effective for 480i and 1080i input signals.

Note: To use the Game Mode feature, the current video input

must be Video 1, Video 2, ColorStream HD1,

ColorStream HD2, HDMI 1, HDMI 2, or HDMI 3. The Game

Mode cannot be turned on when any other video input is

selected.

To turn on Game Mode:

1Press Y and open the Video menu.

2Press B or b to highlight the Game Mode field, and then

press C or c to select On.

To turn off Game Mode:

Select Off in step 2 above, change the video input, or turn the

TV off and then on again.

Note: You can change the video input by pressing + on the

remote control (-page 37).

Using the advanced audio settings

features

Using the SRS WOW™ surround sound

feature

SRS WOW™ is a special combination of SRS Labs audio

technologies (SRS 3D, SRS Focus, and SRS TruBass) that

creates a thrilling surround sound experience with deep, rich

bass from stereo sound sources. Your TV’s audio will sound

fuller, richer, and wider.

To adjust the WOW™ settings:

1Put the TV in STEREO mode (- “Selecting stereo/SAP

broadcasts” on page 47).

2Press Y and open the Audio menu.

3Highlight Advanced Audio Settings and press T.

4Press b or B to highlight the WOW feature you want to

adjust, and then press C or c to adjust the item.

•WOW: SRS 3D — To turn the surround sound effect

On or Off.

Note: If the broadcast is monaural, the SRS 3D effect

will not work.

•WOW: SRS Focus — To turn the vocal emphasis effect

On or Off.

•WOW: SRS TruBass — To select the desired bass

expansion level (Off, Low, or High).

5To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

WOW, SRS and l symbol are trademarks of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc.

Mode

Picture Settings

Noise Reduction

Video

Game Mode

Theater Settings

Off

Sports

Done

Advanced Audio Settings

WOW: SRS 3D

WOW: SRS Focus

WOW: SRS TruBass Low

Reset

Off

50HM67_EN.book Page 59 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 8: Troubleshooting

General troubleshooting

Before calling a service technician, please check this chapter

for a possible cause of the problem and some solutions you can

try.

Black box on-screen

•The closed caption feature is set to one of the Text modes

(T1, T2, T3, or T4). Set the closed caption feature to Off

(-page 45).

TV stops responding to controls

•If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn off the

TV, press and hold the POWER button on the TV control

panel for 5 or more seconds to reset the TV.

Other problems

•If your TV’s problem is not addressed in this

Troubleshooting section or the recommended solution

has not worked, use the Restore Factory Defaults

procedure (-page 36).

TV will not turn on

•Make sure the power cord is plugged in, and then press

•The remote control batteries may be dead. Replace the

batteries or try the control panel buttons.

•If you have recently replaced the lamp unit, make sure the

lamp unit and lamp unit door are installed properly

(- pages 63–65).

•The lamp unit may need to be replaced (- pages 63–65).

Also see “LED indications” (- page 62).

•If the TV is powered off and then quickly on again when

the lamp unit is hot, it may take several minutes for the

picture to appear on-screen. This is a property of DLP®

TV lamp technology and is NOT a sign of malfunction.

For details, see “IMPORTANT NOTICE ABOUT HOT

LAMP RESTART” (- page 6).

Picture problems

General picture problems

•Check the antenna/cable connections (- Chapter 2).

•Press + on the remote control or TV and select a valid

video input source (-page 37). If no device is

connected to a particular input on the TV, no picture will

display when you select that particular input source. For

device connection details, see Chapter 2.

•Antenna reception may be poor. Use a highly directional

outdoor antenna (if applicable).

•The station may have broadcast difficulties. Try another

channel.

•Adjust the picture qualities (-page 44).

•If you are using a VCR, make sure l on the remote

control is set correctly (-page 24).

•Do not connect both a standard video cable and an

S-video cable to the VIDEO 2 input at the same time

(-page 15).

Noisy picture

•If you are watching an analog channel (off-air broadcast

or Cable TV), you can set the CableClear®/DNR

feature to AUTO to reduce visible interference in the TV

picture (-page 58).

Video Input Selection problems

•If the Input Selection window does not appear when

you press + on the remote control or TV, press + a

second time, which will change to the next video input

source and display the Input Selection window.

Cannot view external signals or channel 3 or 4

•If you cannot view signals from external devices

connected to VIDEO 1, VIDEO 2, ColorStream®,

HDMI 1, HDMI 2, HDMI 3, PC, or from channels 3 or 4,

make sure the Input Lock is set to Off (-page 52).

Poor color or no color

•The station may have broadcast difficulties. Try another

channel.

•Adjust the Tint and/or Color (-page 44).

Picture brightness changes soon after turning on TV

•If you set the lamp mode to Low Power, each time you

turn on the TV, the lamp will start out in High Bright

mode but will switch to Low Power mode after a short

period of time. You may notice a change in screen

brightness when this happens. This is normal and is not a

sign of malfunction (- page 57).

Poor composite or S-video picture

•If the TV is connected to an external A/V device (e.g.,

DVD player, video game system, set-top box, etc.) try

using a ColorStream or HDMI video connection

instead.

Picture and sound are out of sync

•As with all products that contain a digital display, in rare

instances, when viewing certain content (e.g.. television

broadcasts, video games, DVDs), you may notice that the

sound and picture are slightly out of sync. This

phenomenon can be caused by various factors including,

without limitation, video processing within the TV, video

processing in an attached gaming system, and video

processing or different compression rates used by

broadcasters in their programming. You may want to try

one or more of the following suggestions, which may

help to reduce the effect of this phenomenon:

– If the TV is connected to an A/V receiver that has a

programmable audio delay feature, use this feature to

help synchronize the sound to the picture.

– If you notice this phenomenon only on certain TV

channels, please contact your local broadcast, cable, or

satellite provider to inform them of this issue.

LED indications while in reboot from standby

•When you plug the power cord in, the yellow LED will

blink until the TV enters standby mode, (plugged in but

not powered on). This is normal and is not a sign of

malfunction.

Sound problems

•Check the antenna/cable connections (- Chapter 2).

•The station may have broadcast difficulties. Try another

channel.

50HM67_EN.book Page 60 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 8: Troubleshooting

•The sound may be muted. Press VOLUME.

•If you hear no sound, try setting the MTS feature to

Stereo mode (-page 47).

•If you are not receiving a second audio program from a

known SAP source, make sure the MTS feature is set to

SAP mode (-page 47).

•If you hear audio that seems “incorrect” for the program

you are watching (such as music or a foreign language),

the SAP mode may be on. Set the MTS feature to Stereo

mode (-page 47).

•When using an external audio amplifier, if you connect

the amplifier to the FIXED AUDIO OUT terminals, the

volume of the amplifier must be set above 0 or you will

not hear any sound (- page 20).

Remote control problems

•Make sure the remote control is set to the correct device

mode (-page 23).

•Remove all obstructions between the remote control and

the TV.

•The remote control batteries may be dead. Replace the

batteries (-page 22).

•Your TV remote control may not operate certain features

on your external device. Refer to the owner’s manual for

your other device to determine its available features. If

your TV remote control does not operate a specific

feature on another device, use the remote control that

came with the device (-pages 24–28).

•If the TV still does not act as expected, use the Reset

Factory Defaults procedure (-page 36).

Channel tuning problems

•Make sure the remote control is set to the correct device

mode (-page 23).

•The channel may have been erased from the channel

memory by the Channel Add/Delete feature. Add the

channel to the channel memory (-page 32).

•The channel may be blocked by the Channels Block

feature. Unblock the channel (-page 51).

•If you are unable to tune digital channels, check the

antenna configuration (-page 31). If you are still

unable to tune digital channels, clear all channels from

the channel list (-page 33) and reprogram channels

into the channel memory (-page 32). If you are still

unable to tune digital channels, use the Reset Factory

Defaults procedure (-page 36). Also see “TV stops

responding to controls” and “Other problems”

(-page 60).

Closed caption problems

•If the program or video you selected is not closed-

captioned, no captions will display (-page 45).

•If text is not available, a black rectangle may appear.

If this happens, turn off the closed caption feature (-

page 45).

•A closed-caption signal may not display correctly in the

following situations: a) when a videotape has been

dubbed; b) when the signal reception is weak; or c) when

the signal reception is nonstandard (-page 45).

Rating blocking (V-Chip) problems

•If you forget your PIN code: While the PIN code entering

screen is displayed, press E four times within 5

seconds. The PIN code you previously stored will be

cleared (-page 49).

•The V-Chip feature is available for the U.S. V-Chip

system only (-page 50).

50HM67_EN.book Page 61 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 8: Troubleshooting

LED indications

The yellow, blue, and red/green LED lights on the TV (at the bottom center of the TV) indicate the TV’s status, as described below.

Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow

LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.

If, after trying the solution, the problem still exists:

•In the U.S., call TACP Consumer Solutions at 1-800-631-3811.

•In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click

“Home Entertainment,” and then click “Support.”

LED Indication Condition Solution Voice

Announce

1) Blue is ON (solid). The TV is operating

properly. ––

2) Green is ON (solid). Power-On Mode Fast. See “Setting the Power-On Mode feature” (- page

35). –

3) Yellow blinks. Standby with Power-On

Mode Fast.

4) Blue is ON (solid).

Yellow blinks.

The lamp is not working

properly.

The TV will automatically try to restart itself eight times

(see item #4).

Note: If the TV is powered off and then quickly on again

when the lamp unit is hot, it may take several minutes

for the picture to appear on-screen. This is a property of

DLP® TV lamp technology and is NOT a sign of

malfunction. For details, see “Setting the Power-On

Mode feature” and “IMPORTANT NOTICE ABOUT

HOT LAMP RESTART” (- page 35).

–

5) Yellow is ON

(solid). Red blinks.

The lamp is not working

properly after the eighth

automatic restart (see

item #3).

Turn the TV OFF and then ON again. If the problem

persists, contact TACP Consumer Solutions at 1-800-

631-3811 in the U.S. or TCL Customer Service at

1-800-268-3404 in Canada.

“Lamp not

working”

6) Yellow is ON

(solid).

The lamp unit door is not

seated properly.

Turn OFF the TV and unplug the power cord. Review

“Lamp unit replacement and care” in Chapter 9 to

ensure that the lamp door is installed securely.

“Lamp door is

open.”

7) Red blinks. Fan stopped.

Turn OFF the TV and unplug the power cord. Plug the

power cord in again and turn ON the TV.

“Fan stopped.”

8) Blue blinks slowly.

Red blinks.

Abnormal operation of

BUS line. (light engine). –

9) Blue blinks slowly. Abnormal operation of

BUS line. –

10)Blue blinks quickly. Power Protect

Detection. –

11)Blue blinks quickly.

Red blinks.

The color wheel has

stopped.

“Color wheel

stopped.”

12)Blue blinks quickly.

Yellow blinks.

Red blinks.

An abnormal

temperature increase

has occurred.

Turn OFF the TV. Check to make sure none of the slots

or openings in the TV cabinet are covered, blocked, or

dusty. Turn ON the TV again.

“Temperature

warning.”

Blue LED Red/Green LEDYellow LED

TV front

“Voice announce” feature

When certain non-standard conditions occur, the LEDs

on the TV will blink and the TV will play a recorded

“voice announcement” describing the condition (see the table below

for the specific conditions that include a voice announcement).

To repeat the voice announcement and hear additional information,

press the MENU button on the TV while the LEDs are blinking.

50HM67_EN.book Page 62 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

Lamp unit replacement and care

Replacing the lamp unit

(User-replaceable component)

The light source for this TV is a mercury lamp with internal

atmospheric pressure that increases during use. The lamp has a

limited service life that varies depending on product use and

user settings.

As is generally the case with all projection TVs that use

projection lamps as a light source, the brightness of the lamp

in this TV may vary somewhat over the expected service life

and will generally decrease over time. Because of the many

variables that can affect the useful service life of the lamp, your

experience may vary from other users.

Note : The lamp is warranted only for the periods and to the

extent set forth in the Limited Warranty applicable to this set.

See “Limited United States Warranty” (- page 67) or “Limited

Canadian Warranty” (- page 68), as applicable.

If you use the lamp beyond its service life:

•you may notice a reduction in the colors and/or brightness of

the picture; and

•the strength of the quartz glass in the lamp will be reduced

and the lamp may rupture (often making a loud noise when

this happens). If the lamp ruptures, the TV will not operate

until the lamp unit is replaced.

When to replace the lamp unit

You should replace the lamp unit:

•if the picture darkens and/or colors fade;

•if the screen (lamp) does not light (LED indication #4,

- page 62); or

•if you hear a loud noise and the picture goes black, which

may indicate a lamp rupture (LED indication #4,

- page 62).

To obtain a replacement lamp unit:

Always replace the lamp unit with the model

currently recommended by Toshiba.

For more information, please contact us at the

telephone numbers or websites listed above, as

applicable.

Using any lamp other than those recommended by

Toshiba may cause damage to the TV and/or lamp.

SUCH DAMAGE IS NOT COVERED UNDER YOUR

TOSHIBA WARRANTY.

WARNING: RISK OF ELECTRIC

SHOCK!

TO REDUCE THE RISK OF ELECTRIC

SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS

SPECIFIED HEREIN. REFER ALL SERVICING NOT

SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE

PERSONNEL. Failure to follow this WARNING may result in

death or serious injury.

CAUTION: Always handle the lamp unit

with care.

The lamp unit in this TV was designed for safe

replacement by consumers; however, if the lamp unit is

subjected to intentional abuse (such as excessive

mechanical abuse or handling by children or pets), the unit

may break, exposing sharp edges or pinch points.

In the U.S.

In warranty: Visit www.tacp.toshiba.com/service or

call toll-free 1-800-631-3811.

Out of

warranty:

Visit

www.ceaccessories.toshiba.com

consult your consumer electronics dealer.

In Canada

Locate a Toshiba parts distributor by visiting

www.toshiba.ca. Click “Home Entertainment” and then

click “Support.”

50HM67_EN.book Page 63 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

How to replace the lamp unit

Required tools:

•Manual screwdrivers (Phillips and slotted)

•Soft, lint-free gloves

1Turn off the TV and unplug the power cord.

2STOP! Allow the lamp to cool for at least one (1) hour

before replacing it.

3On the lamp unit door on the back of the TV, loosen the

screw using a manual screwdriver, and then remove the

lamp unit door.

4Using a manual Phillips screwdriver, loosen the two

screws on the lamp unit.

5Grasp the lamp unit handle and gently pull the lamp unit

straight out of the TV. Set the old lamp unit aside

(- “Disposing of the used lamp unit” on page 65).

6Carefully insert the new lamp unit straight into the TV

until it is fully seated.

WARNING: RISK OF ELECTRIC

SHOCK!

TO REDUCE THE RISK OF ELECTRIC

SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS

SPECIFIED HEREIN. REFER ALL SERVICING NOT

SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE

PERSONNEL. Failure to follow this WARNING may result in

death or serious injury.

WARNING: Eye damage may result from

directly viewing the light produced by

this lamp.

Always turn off the TV and unplug the power cord before

opening the lamp unit door.

Loosen screw

using manual

screwdriver

TV back Lamp unit door detail

WARNING: RISK OF ELECTRIC

SHOCK!

The lamp unit door is provided with an

interlock to reduce the risk of electric shock and excessive

ultraviolet radiation. Never defeat its purpose or attempt

to service without removing the lamp unit door

completely. Failure to follow this WARNING may result in

death or serious injury.

NOTE: Wear soft, lint-free gloves when

replacing the lamp unit.

Lamp unit screws

50HM67

50HM67_EN.book Page 64 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

Note:

•Never subject the lamp unit to excessive shock.

•Never touch the lamp unit glass or otherwise get it dirty.

Doing so may affect the image quality and reduce the

service life of the lamp. See “Cleaning the lamp unit glass”

below.

7Using a manual Phillips screwdriver, tighten the two lamp

unit screws.

Note: Hand-tighten only. Do not use an electric

screwdriver.

8Reattach the lamp unit door, making sure to insert the

hooks on the left side of the lamp unit door inside the

opening in the TV cabinet.

9Replace the screw and tighten using a manual

screwdriver.

10 Plug in the power cord and turn on the TV. After the initial

warmup period (which may take several seconds for full

picture brightness), the TV should operate normally. If

any of the following conditions exist, turn off the TV,

unplug the power cord, and repeat steps 1–9 to ensure that

the lamp unit and lamp unit door are installed correctly:

• No picture

• Dark picture

• TV will not turn on

If, after repeating steps 1–9, the problem still exists:

•In the U.S., call TACP Consumer Solutions at

1-800-631-3811.

•In Canada, locate the nearest Toshiba authorized

service depot by directing your web browser to

www.toshiba.ca; click “Home Entertainment,” and

then click “Support.”

Disposing of the used lamp unit

•Place the used lamp unit in the empty box from the new unit.

•Keep the lamp unit out of reach of children and pets.

•Dispose of the used lamp unit by the approved method for

your area.

CLEANING THE LAMP UNIT GLASS

If you accidentally touch the lamp unit glass or otherwise get

it dirty, wipe it with a lint-free lens cleaning cloth (such as a

cloth for cleaning camera lenses or eyeglasses).

NOTE : Make sure the lamp unit and screws are

installed securely; otherwise, the TV may not turn

on and the lamp life may be shortened.

CAUTION

NEVER

clean a hot lamp with any

type of flammable liquid or aerosol cleaning

agent.

Many ordinary cleaning agents (such as

glass cleaners) contain chemicals that may be flammable at

certain temperatures. If the lamp unit is not allowed to cool for at

least one (1) hour, such chemicals may ignite.

Lamp unit screws

(use manual Phillips screwdriver only)

Insert the hooks inside the

TV cabinet opening.

Lamp unit door

NOTE: Make sure the lamp unit door is installed

securely; otherwise, the TV may not turn on.

CAUTION: Always handle the lamp unit

with care.

The lamp unit in this TV was designed for safe

replacement by consumers; however, if the lamp unit is

subjected to intentional or accidental abuse (such as

excessive mechanical abuse or handling by children or

pets), the unit may break, exposing sharp edges or pinch

points.

NOTE: The lamp unit contains mercury.

Disposal of mercury may be regulated due to

environmental considerations. For disposal or

recycling information, contact your local authorities or the

Electronic Industries Alliance (www.eiae.org).

Hand-tighten using a

manual screwdriver

Lamp unit door

50HM67_EN.book Page 65 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

Specifications

Note:

•This model complies with the specifications listed

below.

•Designs and specifications are subject to change

without notice.

•This model may not be compatible with features and/or

specifications that may be added in the future.

Television System

NTSC standard

ATSC standard (8VSB)

Digital Cable (64 QAM, 256 QAM; in-the-clear,

unencrypted)

Channel Coverage

VHF: 2 through 13

UHF: 14 through 69

Cable TV: Mid band (A-8 through A-1, A through I)

Super band (J through W)

Hyper band (AA through ZZ, AAA, BBB)

Ultra band (65 through 94, 100 through 135)

Power Source

120 V AC, 60 Hz

Power Consumption

50HM67: 200 W (average)

Less than 1W in standby POWER-SAVING

MODE

15W in standby POWER-FAST MODE

57/65HM167: 205 W (average)

Less than 1 W in standby POWER-SAVING

MODE

15 W in standby POWER-FAST MODE

Audio Power

10 W + 10 W

Speaker Type

Main: Two 2-3/8 × 4-3/4 inches (60 × 120 mm) round

Tweeter: Two 1-5/16 inches (33 mm) round

Video/Audio Terminals

S-VIDEO INPUT:

Y: 1 V(p-p), 75 ohm, negative sync.

C: 0.286 V(p-p) (burst signal), 75 ohm

VIDEO/AUDIO INPUT:

VIDEO: 1 V(p-p), 75 ohm, negative sync.

AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k

ohm or greater)

ColorStream® (component video) HD INPUT:

VIDEO:Y: 1V(p-p), 75 ohm

PR: 0.7 V(p-p), 75 ohm

PB: 0.7 V(p-p), 75 ohm

Suggested formats: 1080i, 720p, 480p, 480i

AUDIO: 150 mV(rms), 22 k ohm or greater

HDMI™ INPUT:

HDMI compliant (type A connector)

HDCP compliant

E-EDID* compliant

Suggested formats: 1080p, 1080i, 720p, 480p, 480i,

VGA

HDMI Audio: 2-channel L-PCM; 32/44.1/48 kHz

sampling frequency; 16/20/24 bits per sample

FIXED AUDIO OUTPUT:

150 mv (rms) (30% modulation equivalent, 2.2 k ohm

or less)

DIGITAL AUDIO OUTPUT:

Optical type

IR OUT:

3 V(p-p), 3.5 mm mono socket

PC INPUT:

15-Pin D-sub Analog RGB

Dimensions

50HM67: Width: 47-3/16 inches (1,199 mm)

Height: 30-11/16 inches (780 mm)

Depth: 16-5/8 inches (422 mm)

57HM167: Width: 52-3/8 inches (1,331 mm)

Height: 33-3/4 inches (857 mm)

Depth: 18-3/4 inches (476 mm)

65HM167: Width: 58 inches (1,473 mm)

Height: 37-1/8 inches (942 mm)

Depth: 21-11/16 inches (550 mm)

Mass (weight)

50HM67: 64.0 lbs (29.0 kg)

57HM167: 72.0 lbs (32.6 kg)

65HM167: 83.0 lbs (37.6 kg)

Operating conditions

Temperature: 41ºF - 95ºF (5ºC - 35ºC)

Humidity: 20 - 80% (no moisture condensation)

Supplied Accessories

• Remote control with two size “AAA” batteries

• Owner’s manual (this book)

Optional Stands

50HM67: ST 5067

57HM167:ST 57167

65HM167:ST 65167

*E-EDID = Enhanced-Extended Display Identification

Pin No. Signal name Pin No. Signal name

1R 9NC

2 G 10 Ground

3B 11NC

4NC

(Not connected) 12 NC

5NC 13H-sync

6 Ground 14 V-sync

7 Ground 15 NC

8 Ground

50HM67_EN.book Page 66 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

Limited United States Warranty

for DLP® Television Models

Toshiba America Consumer Products, L.L.C. (“TACP”) makes the

following limited warranties to original consumers in the United States.

THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL

CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP

TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER

PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.

DLP

TELEVISIONS PURCHASED IN THE U.S.A. AND USED

ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT

LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE

WARRANTIES.

DLP

TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE

U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO,

AND USED IN THE U.S.A., ARE NOT COVERED BY THESE

WARRANTIES.

Limited One (1) Year Warranty on Parts and Labor

TACP warrants this DLP

Television and its parts against defects in

materials or workmanship for a period of one (1) year after the date of

original retail purchase.

DURING THIS PERIOD, TACP WILL, AT TACP'S

OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR

REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR

LABOR.

During this period, TACP Authorized Service Station personnel

will come to your home when warranty service is required. Depending on

the type of repair required, the service will either be performed in your

home or the DLP

Television will be taken to a TACP Authorized Service

Station for repair and returned to your home at no cost to you.

Limited One (1) Year Warranty on Lamp Unit

TACP warrants the original lamp unit contained in this DLP

Television

against defects in materials or workmanship for a period of one (1) year

after the date of original retail purchase.

DURING THIS PERIOD, TACP

WILL, AT TACP'S OPTION, EXCHANGE A DEFECTIVE LAMP UNIT

WITH A NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO

YOU. LABOR CHARGES FOR LAMP UNIT REPLACEMENT ARE YOUR

RESPONSIBILITY AND ARE NOT COVERED UNDER THIS

WARRANTY.

The lamp unit is a user-replaceable component.

Rental Units

The warranty for DLP

Television rental units begins on the date of the first

rental or thirty (30) days after the date of shipment to the rental firm,

whichever comes first.

Limited Warranty for Commercial Units

TACP warrants DLP

Televisions, including the lamp units contained

therein, that are sold and used for commercial purposes as follows: all

parts are warranted against defects in materials or workmanship for a

period of ninety (90) days after the date of original retail purchase.

DURING THIS PERIOD, TACP WILL, AT TACP'S OPTION, REPAIR OR

REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART

WITHOUT CHARGE TO YOU.

Owner's Manual and Product Registration Card

Read this owner’s manual thoroughly before operating this DLP

Television.

Complete and mail the enclosed product registration card or register your

DLP

Television online at

www.tacp.toshiba.com/service

as soon as

possible. By registering your DLP

Television you will enable TACP to bring

you new products specifically designed to meet your needs and help us to

contact you in the unlikely event a safety notification is required under the

U.S. Consumer Product Safety Act. Failure to complete and return the

product registration card does not diminish your warranty rights.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING

CONDITIONS:

(1) You must retain your original bill of sale or provide other proof of

purchase.

(2) All warranty servicing of this DLP

Television must be performed by

an Authorized TACP Service Station.

(3) The warranties from TACP are effective only if this DLP

Television is

purchased and operated in the Continental U.S.A. or Puerto Rico.

(4) Labor service charges for set installation, setup, adjustment of

customer controls, and installation or repair of antenna systems are

not covered by this warranty. Reception problems caused by

inadequate antenna systems, misaligned satellite dishes, cable

television distribution, VCRs, DVD players/recorders, personal

computer level IEEE 1394 devices, and any other connected signal

source device are your responsibility.

(5) Warranties extend only to defects in materials or workmanship as

limited above, and do not extend to any DLP

Television or parts that

have been lost or discarded by you or to damage to the DLP

Television or parts caused by fires, misuse, accident, Acts of God

(such as lightning or fluctuations in electric power), improper

installation, improper maintenance, or use in violation of instructions

furnished by TACP; use or malfunction through simultaneous use of

this DLP

Television and connected equipment; or to units that have

been modified or had the serial number removed, altered, defaced,

or rendered illegible.

How to Obtain Warranty Service

If, after following all of the operating instructions in this manual and

reviewing the section entitled “Troubleshooting,” you find that service is

needed:

(1) To find the nearest TACP Authorized Service Station, visit TACP’s

website at

www.tacp.toshiba.com/service

or contact TACP’s

Consumer Solution Center toll free at 1-800-631-3811.

(2) You must present your original bill of sale or other proof of purchase

to the TACP Authorized Service Station.

ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE

U.S.A., INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED

WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY

WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.

AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,

AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH

RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO

EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST

PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR

ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR

INABILITY TO USE THIS DLP

TELEVISION).

No person, agent, distributor, dealer, or company is authorized to change,

modify, or extend the terms of these warranties in any manner whatsoever.

The time within which an action must be commenced to enforce any

obligation of TACP arising under the warranty or under any statute or law

of the United States or any state thereof is hereby limited to ninety (90)

days from the date you discover, or should have discovered, the defect.

This limitation does not apply to implied warranties arising under the law

of any state of the U.S.A.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU

MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE

TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT

ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED

WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY

TO YOU UNDER SUCH CIRCUMSTANCES. 05

For additional information, visit TACP's website:

www.tacp.toshiba.com.

50HM67_EN.book Page 67 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

Limited Canadian Warranty

for Toshiba Brand DLP® Television Models

Toshiba of Canada Limited (“

TCL

”) makes the following limited warranties

to original consumers in Canada.

THESE LIMITED WARRANTIES

EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY

PERSON RECEIVING THIS TOSHIBA BRAND DLP

TELEVISION

MODEL (the “TELEVISION(S)” or “Television(s)”) AS A GIFT FROM THE

ORIGINAL CONSUMER PURCHASER AND TO NO OTHER

PURCHASER OR TRANSFEREE.

TELEVISIONS PURCHASED IN CANADA, AND USED ANYWHERE

OUTSIDE OF CANADA INCLUDING, WITHOUT LIMITATION, THE

UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE

WARRANTIES.

TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF CANADA,

INCLUDING, WITHOUT LIMITATION, THE UNITED STATES AND

MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE

WARRANTIES.

Limited One (1) Year Warranty on Parts and Labour

Subject to the more limited warranty if the Television is used for any

commercial or business purposes as set out below, TCL warrants the

Television and its parts, excluding the lamp unit, against material defects

in materials or workmanship that result in the Television failing for a period

of one (1) year after the date of original retail purchase.

DURING THIS

PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE A

DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT

CHARGE TO YOU FOR PARTS OR LABOR.

During this period, TCL

Television authorized service provider (“

ASP

”) personnel will come to

your home when warranty service is required. Depending on the type of

repair required, the service will either be performed in your home or the

Television will be taken to an ASP for repair and returned to your home at

no cost to you.

IN-HOME SERVICE ONLY APPLIES WITHIN 100

KILOMETERS OF AN ASP. IF YOU ARE NOT WITHIN 100

KILOMETERS OF AN ASP, YOU MUST DELIVER THE ENTIRE

TELEVISION TO AN ASP. YOU MUST PAY FOR ALL

TRANSPORTATION AND INSURANCE CHARGES FOR THE

TELEVISION TO AND FROM THE ASP.

Limited One (1) Year Warranty on the Lamp Unit

TCL warrants the lamp unit in this Television against material defects in

materials or workmanship for a period of one (1) year after the date of

original retail purchase.

DURING THIS PERIOD, TCL WILL, AT TCL'S

OPTION, REPAIR OR REPLACE THE DEFECTIVE LAMP UNIT WITH A

NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO YOU

FOR THE LAMP UNIT. YOU MUST DELIVER THE ENTIRE LAMP UNIT

TO AN ASP. YOU MUST PAY FOR ALL TRANSPORTATION AND

INSURANCE CHARGES FOR THE LAMP UNIT TO AND FROM THE

ASP.

Limited Warranty for Commercial Units

TCL warrants Televisions that are used for any commercial or business

purposes as follows: all parts are warranted against material defects in

materials or workmanship that result in the Television failing for a period of

ninety (90) days after the date of original retail purchase.

DURING THIS

PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE THE

DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT

CHARGE TO YOU. ON-SITE SERVICE ONLY APPLIES WITHIN 100

KILOMETERS OF AN ASP. IF YOU ARE NOT WITHIN 100 KILOMETERS

OF AN ASP, YOU MUST DELIVER THE ENTIRE TELEVISION TO AN

ASP. YOU MUST PAY FOR ALL TRANSPORTATION AND INSURANCE

CHARGES FOR THE TELEVISION TO AND FROM THE ASP.

Rental Units

The warranty for Television rental units begins with the date of first rental

or thirty (30) days from the date of shipment to the rental firm, whichever

comes first.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING

CONDITIONS:

(1) You must provide your bill of sale or other proof of purchase.

(2) All warranty servicing of this Television must be performed by an ASP.

(3) The warranties from TCL are effective only if the Television is (i)

purchased as new and unopened from TCL or from TCL’s authorized

distributors, dealers or resellers (“

ADR’s

”) and (ii) located/operated

in Canada.

(4) Labour charges for set installation, setup, adjustment of customer

controls, and installation or repair of antenna systems are not covered

by these warranties. Reception problems caused by inadequate

antenna systems are your responsibility.

(5) Warranties extend only to material defects in materials or

workmanship as limited above, and do not extend to:

a) Service, repairs or replacement made necessary by accident,

misuse, abuse, moisture, liquids, dust, dirt, neglect, accident,

damage, 24/7 applications, improper installation, improper

operation, improper cleaning, improper maintenance, normal

wear and tear, or any other external cause or event, act or

omission outside the control of TCL, including fire, theft, acts of

God, alteration, power failures, power surges or power shortages,

lightning, other electrical faults, or repairs, modifications or

replacements by persons other than those authorized by TCL to

service the Television;

b) Replacement of missing, discarded or lost parts, the provision of

retrofits, or preventive maintenance;

c) Repair of damage that is cosmetic only or does not affect the

Television functionality, such as wear and tear, scratches and

dents;

d) Service on Toshiba-branded accessory items (such accessory

items may be covered by their own warranty);

e) Service on third party products or service made necessary by

use of incompatible third party products;

f) Service made necessary by the simultaneous use of this

Television and connected equipment;

g) Modifications to the Television not approved in writing by TCL,

and service made necessary by the use or installation of non-

Toshiba modifications to the Television;

h) Service of a Television on which the TOSHIBA label or logo, rating

label or serial number have been defaced or removed;

i) On-site service and repair of the Television; and

j) Damage to the Television caused by failure to follow the

specifications, User manuals or guides as to usage and/or

storage.

Disclaimer and Limitation of Remedy

TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER EXPRESS

AND IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS

FOR THIS TELEVISION, INCLUDING THE IMPLIED WARRANTIES,

CONDITIONS AND REPRESENTATIONS OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED

AND EXCLUDED. IF THE APPLICABLE LAW, STATUTORY OR

OTHERWISE, PRECLUDES THE EXCLUSION OF ANY IMPLIED

WARRANTIES, CONDITIONS AND REPRESENTATIONS THEN SUCH

IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS ARE

OTHERWISE LIMITED IN DURATION TO THE TERM OF THIS

EXPRESS WRITTEN LIMITED WARRANTY. TO THE EXTENT NOT

PRECLUDED BY LAW, STATUTORY OR OTHERWISE, THIS WRITTEN

WARRANTY SUPERCEDES AND SPECIFICALLY DISCLAIMS ANY

OTHER WARRANTY, CONDITION OR REPRESENTATION NOT

STATED IN THIS WARRANTY, WHETHER MADE BY TCL, TOSHIBA

CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND

WHETHER MADE ORALLY OR IN WRITING (INCLUDING ANY

STATEMENT IN ANY BROCHURE, PRESS RELEASE,

ANNOUNCEMENT, ADVERTISEMENT, POINT OF SALE DISPLAY,

ETC.).

50HM67_EN.book Page 68 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE

INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR

MANUALS. IF YOU FAIL TO DO SO, THIS TELEVISION MAY NOT

FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE. THIS

WARRANTY WILL NOT COVER ANY SERVICE THAT IS REQUIRED, IN

PART OR IN WHOLE, AS A RESULT OF ANY FAILURE TO FOLLOW THE

SET-UP AND USAGE INSTRUCTIONS. THIS WARRANTY DOES NOT

APPLY AND SHALL BE VOID AND UNENFORCEABLE IF THE

TELEVISION IS OPENED, SERVICED, OR REPAIRED BY PERSONS

OTHER THAN THOSE AUTHORIZED BY TCL TO SERVICE OR REPAIR

THE TELEVISION.

IF THE TELEVISION FAILS TO WORK AS WARRANTED ABOVE, YOUR

SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT

OF THE DEFECTIVE PART. IN NO EVENT WILL TCL, TOSHIBA

CORPORATION, THEIR AFFILIATES, ADRs OR ASPs (THE “

PARTIES

”) BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY

DAMAGES, MONEY, REIMBURSEMENT, COSTS OR EXPENSES. THIS

LIMITATION APPLIES TO DAMAGES, MONEY, REIMBURSEMENT,

COSTS OR EXPENSES OF ANY KIND WHATSOEVER INCLUDING ANY

DIRECT OR INDIRECT DAMAGES, DAMAGE TO PROPERTY OR

PERSON, LOST PROFITS, LOST SAVINGS, INCONVENIENCE OR

OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL

DAMAGES, WHETHER FOR BREACH OF WARRANTY, BREACH OF

CONTRACT, TORT (INCLUDING NEGLIGENCE), UNDER A STATUTE OR

UNDER ANY OTHER LAW OR FORM OR ACTION, OR WHETHER

ARISING OUT OF THE USE OF OR INABILITY TO USE THE TELEVISION,

EVEN IF ANY OF THE RELATED PARTIES HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER

PARTY.

No person, agent, distributor, dealer or company is authorized to change,

modify or extend the terms of these warranties in any manner whatsoever.

Arbitration and Dispute Resolution

To the extent not precluded by law, any claim, dispute, controversy or

disagreement (whether for breach of warranty, breach of contract, tort

(including negligence), under a statute or under any other law or form of

action) against any of the Related Parties arising out of, or otherwise

relating to: (i) this warranty; (ii) the Television; (iii) any oral or written

representations, statements, brochures, press releases, advertising,

announcement, point of sale display, or promotional material relating to the

Television; (iv) the relationships that result from this warranty, (the

foregoing claims, disputes controversies and disagreements are

collectively referred to as the “Dispute”), shall be referred to and resolved

by final and binding arbitration (to the exclusion of the courts). To the

extent not precluded by law, you agree to waive any right that you may

have to commence or participate in any representative or class proceeding

against the Related Parties relating to any Dispute. If and where applicable

and to the extent not precluded by law, you further agree to opt out of any

such representative or class proceedings. Arbitration of any Dispute will

be conducted in the forum and in the manner as agreed to between you

and TCL. Failing such agreement, the arbitration will be conducted by one

arbitrator pursuant to the laws and rules relating to arbitration generally in

force in the jurisdiction in which you reside at the time that the Dispute

arises. To the extent not precluded by law, no claim, dispute, controversy

or disagreement of any other person may be joined or combined with any

Dispute by you, without the prior written consent of TCL.

Critical Applications

The Television you have purchased is not designed for any “critical

applications.” “Critical applications” means life support systems, medical

applications, connections to implanted medical devices, commercial

transportation, nuclear facilities or systems or any other applications

where Television failure could lead to injury to persons or loss of life or

catastrophic property damage.

IF THE CUSTOMER USES THE TELEVISION IN ANY CRITICAL

APPLICATION, THE CUSTOMER - AND NOT TCL, ITS AFFILIATES, ADRs

OR ASPs - ASSUME SOLE AND FULL RESPONSIBILITY FOR SUCH USE.

TCL RESERVES THE RIGHT TO REFUSE TO SERVICE ANY TELEVISION

USED IN A CRITICAL APPLICATION. TCL, ITS AFFILIATES, ADRs AND

ASPs HEREBY DISCLAIM ANY AND ALL LIABILITY, DAMAGES AND

CONSEQUENCES ARISING OUT OF THE SERVICE OR REFUSAL TO

SERVICE SUCH TELEVISION AND FURTHER DISCLAIM ANY AND ALL

LIABILITY, CONSEQUENCES AND DAMAGES THAT MAY ARISE OR

RESULT FROM THE USE OF THE TELEVISION IN ANY CRITICAL

APPLICATIONS.

General Provisions

If and to the extent that any provision of this limited warranty should

generally be found to be unenforceable, the unenforceable provision shall

be severed from the warranty and deemed not to form part of the warranty.

The remaining provisions of this warranty shall be and remain valid and

enforceable. If and to the extent that any provision of this limited warranty

as it relates to any of the Related Parties is found to be invalid or

unenforceable in respect of that party (the “

Excluded Party

”), the

Excluded Party shall be deemed to be severed or excluded from the

provision, and the provision shall remain valid, enforceable and

applicable in respect of the other or remaining Related Parties.

To the extent permitted by law, this limited warranty shall be governed and

construed in accordance with the laws of Ontario.

If there is any inconsistency between this limited warranty, on the one

hand, and any statement in the packaging of the Television or in any other

document enclosed with, or used in the context of the promotion or sale

of, the Television, on the other hand, the provisions of this limited warranty

shall prevail.

How to Obtain Warranty Services

If, after following all of the operating instructions in this manual and

checking the “Troubleshooting” section, you find that service is needed:

(1) To find the nearest ASP, visit TCL's web site at

www.toshiba.ca

, or

call toll free 1-800-268-3404

(2) Present your bill of sale or other proof of purchase to the ASP.

For additional information, visit TCL's website at

www.toshiba.ca

50HM67_EN.book Page 69 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Chapter 9: Appendix

A copy of the GPL source code in this product may be obtained by

contacting Toshiba Consumer Solutions at (800)631-3811. There will be

a charge to cover the costs of providing the source code.

A copy of the LGPL source code in this product may be obtained by

contacting Toshiba Consumer Solutions at (800)631-3811. There will be

a charge to cover the costs of providing the source code.

reserved.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

(1) Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) Neither the name of The NetBSD Foundation nor the names of its

contributors may be used to endorse or promote products derived

from this software without specified prior written permission.

THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.

AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL

THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

This product includes software developed by the OpenSSL Project for use

in the OpenSSL Toolkit (http://www.openssl.org).

This product includes cryptographic software written by Eric Young

(eay@cryptsoft.com).

reserved. Redistribution and use in source and binary forms, with or

without modification, are permitted provided that the following conditions

are met:

(1) Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) All advertising materials mentioning features or use of this software

must display the following acknowledgement: This product includes

software developed by the OpenSSL Project for use in the OpenSSL

Toolkit (http://openssl.org).

(4) The names “OpenSSL Toolkit” and “Open SSL Project” must not be

used to endorse or promote products derived from this software

without prior written permission. For written permission, please

contact openssl-core@openssl.org.

(5) Products derived from this software may not be called “OpenSSL” nor

may “Open SSL” appear in their names without prior written

permission of the OpenSSL Project.

(6) Redistributions of any form whatsoever must retain the following

acknowledgement: “This product includes software developed by the

OpenSSL Project for use in the OpenSSL Toolkit (http://

www.openssl.org).”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”

AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN

IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product

includes cryptographic software written by Eric Young

(eay@cryptsoft.com). This product includes software written by Tim

Hudson (tjh@cryptsoft.com).

reserved. This package is an SSL implementation written by Eric Young

(eay@cryptsoft.com). The implementation was written so as to conform

with Netscapes SSL. This library is free for commercial and non-

commercial use so long as the following conditions are adhered to. The

following conditions apply to all code found in this distribution, be it the

RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL

documentation included with this distribution is covered by the same

the code are not to be removed. If this package is used in a product, Eric

Young should be given attribution as the author of the parts of the library

used. This can be in the form of a textual message at program startup

or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

(1) Redistributions of source code must retain the copyright notice, this

list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) All advertising materials mentioning features or use of this software

must display the following acknowledgement: “This product includes

cryptographic software written by Eric Young (eay@cryptsoft.com).”

The word ‘cryptographic’ can be left out if the routines from the library

being used are not cryptographic related.

(4) If you include any Windows specific code (or derivative thereof) from

the apps directory (application code) you must include an

acknowledgement: “This product includes software written by Tim

Hudson (tjh@cryptosoft.com).”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE. The license and distribution terms for any publicly available

version or derivative of this code cannot be changed, i.e. this code cannot

simply be copied and put under another distribution license (including the

GNU Public License).

50HM67_EN.book Page 70 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Index

Antenna cable ................................ 13

Antenna input configuration ............ 31

Audio quality adjustments ............... 47

Audio system connection ................ 20

Auto aspect.................................... 43

Auto power off ................................ 55

Back of the TV................................ 12

Base closed captions...................... 45

Blocking channels .......................... 51

Cable box connection ..................... 15

CableClear®..................................... 58

Camcorder connection.................... 18

CH Bb buttons ........................ 23, 40

CH RTN button......................... 23, 40

Channel Browser Setup.................. 38

Channel Browser™........................... 38

Channel labeling ............................ 33

Channel Number buttons .......... 23, 40

Channel programming

Automatic programming ........... 32

Manually adding and deleting... 32

Cinema mode................................. 43

Closed captions.............................. 45

Color temperature .......................... 57

ColorStream®................................... 16

Component video ........................... 16

Component video cables ................ 13

Connecting cables.......................... 13

Digital Audio Out ............................ 20

Digital audio selector ...................... 46

Digital CC Settings ......................... 45

Digital signal meter......................... 35

Dolby Digital................................... 20

Dolby Digital Dynamic Range

Control....................................... 48

DVD player connection ................... 16

DVI connection............................... 19

Dynamic contrast............................ 56

Features, TV .................................... 9

Front of the TV ............................... 11

Game Mode feature........................ 59

HDMI audio mode........................... 34

HDMI cable .................................... 13

HDMI™ connection.......................... 19

INFO button.................................... 55

INPUT button.................................. 37

Installation, care, and service ............3

Installation, setup............................ 10

Integrated digital tuning..................... 9

IR blaster........................................ 17

IR OUT connection ......................... 17

Labeling video input........................ 37

Lamp mode .................................... 57

Lamp unit replacement....................63

Language selection......................... 31

Last mode memory feature .............55

LED indications.........................11, 62

LOCKS menu

Channels, blocking...................51

Enable rating blocking ..............50

New PIN code.......................... 49

Panel lock................................53

Unlocking programs

temporarily.................52

Video inputs, locking ................ 52

Locks menu.................................... 49

MPEG noise reduction ....................58

MTS feature ................................... 47

MUTE button .................................. 46

Optical audio cable ......................... 13

Optical audio output format .............48

PC Audio........................................ 54

PC connection ................................ 21

PC settings..................................... 53

Picture adjustment..........................44

Picture mode .................................. 44

Picture quality................................. 44

Picture scroll................................... 42

Picture size selection ...................... 41

POWER button.........................11, 23

Power-On Mode ............................. 35

RECALL button...............................55

Remote control

Battery installation....................22

Device code table.....................27

Effective range.........................22

Functional key chart .................25

Learning about the buttons .......23

Programming ...........................26

Reset Factory Defaults....................36

Safety...............................................2

SAP sound .....................................47

Satellite receiver connection............16

Scroll settings .................................42

Selecting Menu Language...............31

Service .............................................4

Side panel control ...........................11

Sleep timer .....................................54

Specifications .................................66

StableSound®................................... 48

Stereo sound ..................................47

SurfLock™........................................ 40

S-video cable..................................13

System status .................................36

TheaterWide® picture size ...............41

Troubleshooting ..............................60

TV status information ......................55

V-Chip blocking (Locks menu) .........49

VCR connection................. 14, 15, 16

Video cables ...................................13

Video input label .............................37

Video input lock ..............................52

Warranty

Canada....................................68

U.S. .........................................67

WOW:SRS 3D ................................59

WOW:SRS Focus ...........................59

WOW:SRS TruBass........................59

50HM67_EN.book Page 71 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Notes

50HM67_EN.book Page 72 Wednesday, February 14, 2007 4:18 PM

HM67 (E/F) Web 213:276

Notes

50HM67_EN.book Page 73 Wednesday, February 14, 2007 4:18 PM

Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.

NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.

PRINTED IN USA

(07-03)

CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.

Channel Browser and SurfLock are trademarks of Toshiba America Consumer Products, L.L.C.

DLP® and the DLP logo are registered trademarks of Texas Instruments.

MANUFACTURED BY

HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400

SERVICE CENTERS:

TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400

MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766

VANCOUVER: 13551 COMMERCE PARKWAY, SUITE 110, RICHMOND, B.C., V6V 2L1, CANADA – TEL: (604) 303-2500

HM67 (E/F) Web 213:276

50HM67_EN.book Page 74 Wednesday, February 14, 2007 4:18 PM

65HM167 50HM67 OM E

Navigation menu

Versions of this User Manual:

Views

Navigation