603 4V&4VK V3.0 Manual Single Button

603 4V&4VK V3.0 manual 603 4V&4VK V3.0 manual

User Manual: 603 4V&4VK V3.0 manual - single button

Open the PDF directly: View PDF PDF.
Page Count: 1

Download603 4V&4VK V3.0 Manual - Single Button
Open PDF In BrowserView PDF
Installation Manual

Ver 3

for
603V & VK (4000 series) Wireless Intercom System
Testing

Installation

1) Before installing fully, test the range of the system. Wire the unit as per
wiring diagram, place the equipment in the desired location and test
operation.
2) Ensure that the gate transmitter / receiver unit is installed to facilitate
line of sight with the property or reception area. To achieve best results,
mount the unit as high as possible from the ground. Should you need to
extend range, you can mount it on a small pole to elevate it a few meters
from the ground.
House or
reception
area

150m
Typical
Entrance
Pillar

For longer range
applications, locate the
handset near a window at
front of property.
Note: Wood and glass only
reduce signal strength by
10-20%. Masonry will reduce
signal strength by 20-50%
per wall. Metal can totally
block signals.

Transmitter / receiver - Keep
away from ground, as high as
possible. For best results, do
not install too close to sources
of electrical interference e.g.
gate automation panel

Speech
Unit

3) It is recommended to charge the handset for 7-8 hours before use.
4) Power up the handset after inserting the batteries.
5) Wire the door station and transmitter / receiver according to the diagram
below..

Use cable entry
through back
panel knockout
at bottom, not
top!

Never drill holes in
the top of the
enclosure. Cable
entry should be
through the bottom.

Transmitter

Foil screening
wrapped
around MIC
wires for best
performance!

MIC
connections

+
GND

Speech Panel Connections

Solid
shield
wire

P4

2
P3

3
1

S
S1

Speaker

C
C1
P1
P2

Button

Code
button

N/C N/O
Relay output
(4 sec pulse)

-+
12v
dc in

A/C 12-24v
(optional)

Shielded CAT5 cable
Volt free relay output

ADJUST VOLUME
Press or
to adjust volume level,
and press MENU to select and save.
CHANGE RING TONE
Press
and the unit will ring under
the currently select tone. Press
and
to cycle through available
ring tones. Press MENU to select
and save.
CHANGE LANGUAGE
Press
and the unit will display the
currently selected language.
1=English. Press
and
to
cycle. Press MENU to select and
save.

12.21

Voicemail
Symbol
Vibration
ON/OFF

ON/OFF
MENU

Charging
base

Code
Button

Power
LED

= Continue

= Delete, long
press = delete all.

Coding another handset to the System
To add an extra handset to the system, follow the sequence below..
1) Press and HOLD the code button on the door station for 3 seconds,
until the LED’s on the bottom of the board start to flash.
2) Press and hold the Code button on the new handset ignoring the first
short tone, until you hear a confirmation tone (“Di-Do-Do”). This may take
up to 10 seconds.
3) Once the door station lights stop flashing, then you can test the
system by pressing the call button on the door station. The new handset
should ring. If not, repeat the process from the top.
Note: For earlier models, the existing master handset lights will
flash after step 1. You will need to press the MENU button on the
existing handset first, before proceeding to step 2 above.

Keypad Programming (only for VK model)

Note: Shield only connects at one end

NO3
C3
NC2
NO2
C2
NC1
NO1
C1
+

SW1
NC3

SW2

Battery
Level

SET TIME ON DISPLAY
Press MENU for 2 seconds. The hour digits will begin flashing.
Press
or
to adjust. Press MENU to cycle from hour setting to
minutes and repeat. Press MENU a third time to exit and save changes.

Enter engineers code

Factory
default is
111111

Press ENTER

Keypad Connections (VK models only)

Microphone

Reception
indicator

VOICEMAIL
When the door station is pressed, and not answered within 40 seconds,
the visitor can leave a message. Once complete, the handset will display
the
symbol. Up to 16 messages can be saved.

= Pause / Exit

603 Range

(keep short for better audio)

Handset & Operation

To listen to voicemail, press MENU to play. If there are more than 1
message, press
and
to select the message required and press
MENU to play.

Intercom

8 meters max
Screened CAT 5

1) Check all connections are correct before switching on the power.
2) Press the call button on the speech panel.
3) The handset should ring.
4) Press the
button to answer the call and check two way speech.
5) Press
to check the door / gate release function works.

Press ENTER

Confirm or change
engineers code
IMPORTANT:
Observe microphone polarity.

Enter access code for
relay 1

Enter pulse time for
relay 1

Enter access code for
relay 2

Enter pulse time for
relay 2

Enter access code for
relay 3
4-8 digits

Press ENTER
Enter pulse time for
relay 3
Press ENTER

2 digits, 01-99.
E.g. 03=3 sec
Press ENTER

FINISH
Red LED should now be
OFF



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Language                        : en-GB
Tagged PDF                      : Yes
Title                           : 
Author                          : OEM User
Subject                         : 
Create Date                     : 2012:12:19 16:36:39
Modify Date                     : 2012:12:19 16:36:39
Producer                        : Microsoft® Office Visio® 2007
Creator                         : Microsoft® Office Visio® 2007
EXIF Metadata provided by EXIF.tools

Navigation menu