603 4V&4VK V3.0 Manual Single Button

603 4V&4VK V3.0 manual 603 4V&4VK V3.0 manual

User Manual: 603 4V&4VK V3.0 manual - single button

Open the PDF directly: View PDF PDF.
Page Count: 1

Installation Manual
for
603V & VK (4000 series) Wireless Intercom System
MENU
12.21
Charging
base
Entrance
Pillar
Transmitter / receiver - Keep
away from ground, as high as
possible. For best results, do
not install too close to sources
of electrical interference e.g.
gate automation panel
Speech
Unit
House or
reception
area
Note: Wood and glass only
reduce signal strength by
10-20%. Masonry will reduce
signal strength by 20-50%
per wall. Metal can totally
block signals.
For longer range
applications, locate the
handset near a window at
front of property.
150m
Typical
Installation
1) Before installing fully, test the range of the system. Wire the unit as per
wiring diagram, place the equipment in the desired location and test
operation.
2) Ensure that the gate transmitter / receiver unit is installed to facilitate
line of sight with the property or reception area. To achieve best results,
mount the unit as high as possible from the ground. Should you need to
extend range, you can mount it on a small pole to elevate it a few meters
from the ground.
3) It is recommended to charge the handset for 7-8 hours before use.
4) Power up the handset after inserting the batteries.
5) Wire the door station and transmitter / receiver according to the diagram
below..
Never drill holes in
the top of the
enclosure. Cable
entry should be
through the bottom.
Screened CAT 5
8 meters max
603 Range
Intercom
Transmitter
Use cable entry
through back
panel knockout
at bottom, not
top!
12v
dc in
+
-
N/C N/O
A/C 12-24v
(optional)
Shielded CAT5 cable
Solid
shield
wire
Relay output
(4 sec pulse)
Code
button
Note: Shield only connects at one end
Testing
1) Check all connections are correct before switching on the power.
2) Press the call button on the speech panel.
3) The handset should ring.
4) Press the button to answer the call and check two way speech.
5) Press to check the door / gate release function works.
Handset & Operation
Power
LED
ON/OFF Vibration
ON/OFF
Voicemail
Symbol
Battery
Level
Reception
indicator
ADJUST VOLUME
Press or to adjust volume level,
and press MENU to select and save.
CHANGE RING TONE
Press and the unit will ring under
the currently select tone. Press
and to cycle through available
ring tones. Press MENU to select
and save.
CHANGE LANGUAGE
Press and the unit will display the
currently selected language.
1=English. Press and to
cycle. Press MENU to select and
save.
VOICEMAIL
When the door station is pressed, and not answered within 40 seconds,
the visitor can leave a message. Once complete, the handset will display
the symbol. Up to 16 messages can be saved.
To listen to voicemail, press MENU to play. If there are more than 1
message, press and to select the message required and press
MENU to play.
= Pause / Exit = Continue = Delete, long
press = delete all.
SET TIME ON DISPLAY
Press MENU for 2 seconds. The hour digits will begin flashing.
Press or to adjust. Press MENU to cycle from hour setting to
minutes and repeat. Press MENU a third time to exit and save changes.
Coding another handset to the System
Code
Button
Foil screening
wrapped
around MIC
wires for best
performance!
+
-
GND
MIC
connections
To add an extra handset to the system, follow the sequence below..
1) Press and HOLD the code button on the door station for 3 seconds,
until the LED’s on the bottom of the board start to flash.
2) Press and hold the Code button on the new handset ignoring the first
short tone, until you hear a confirmation tone (“Di-Do-Do”). This may take
up to 10 seconds.
3) Once the door station lights stop flashing, then you can test the
system by pressing the call button on the door station. The new handset
should ring. If not, repeat the process from the top.
(keep short for better audio)
P4
P3
C
P1
SW1
NC3
NO3
C3
C2
NC2
NO2
C1
NC1
NO1
-
+
Volt free relay output
Keypad Connections (VK models only)
Speech Panel Connections
C1
P2
S
S1
3
1
2
SW2
SpeakerButton
Microphone
Keypad Programming (only for VK model)
Enter engineers code Factory
default is
111111
Confirm or change
engineers code
Press ENTER
Enter access code for
relay 1
Enter pulse time for
relay 1
Enter access code for
relay 2
4-8 digits
2 digits, 01-99.
E.g. 03=3 sec
Enter pulse time for
relay 2
Enter access code for
relay 3
Enter pulse time for
relay 3
FINISH
Red LED should now be
OFF
Press ENTER
Press ENTER
Press ENTER
Press ENTER
IMPORTANT:
Observe microphone polarity.
Ver 3
Note: For earlier models, the existing master handset lights will
flash after step 1. You will need to press the MENU button on the
existing handset first, before proceeding to step 2 above.

Navigation menu