54 40 1625 MILWAUKEE 6370 20 (SER A35A)
User Manual: MILWAUKEE 6370-20
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
BULLETIN NO. SERVICE PARTS LIST 54-40-1625 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 00 METAL CUTTING SAW CATALOG NO. 6370-20 SERIAL NUMBER EXAMPLE: 0 Component Parts (Small #) Are Included When Ordering The Assembly (Large #). REVISED BULLETIN DATE May 2003 A35A WIRING INSTRUCTION 58-01-0085 SEE REVERSE SIDE FOR LUBRICATION AND SERVICE NOTES Orient the external retaining ring (37) such that the beveled face is towards the lower guard (27). Place the bearing cup (45) into the motor housing (34) prior to installing the armature (15). FIG. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO. 02-04-0852 02-04-1050 02-50-0015 05-71-0035 05-78-0305 05-88-9925 06-75-0035 06-75-5860 06-82-3792 06-82-5314 06-82-7270 06-82-7453 10-20-0002 12-20-0230 16-62-1015 18-62-1015 22-16-0060 22-22-0260 22-64-0345 22-84-0035 23-52-0020 23-66-2115 23-94-0010 28-14-0015 28-20-0015 28-20-0020 28-41-0015 31-05-0075 31-15-0030 31-15-0035 31-44-0205 DESCRIPTION OF PART NO REQ. Bearing (1) Bearing (1) Needle Bearing (1) Screws (4) M3.5 x 0.6 x 7.00mm Pan Hd.Slt. T-15 (4) TS5 x 30mm Phillips Hd. Screw (4) 5/16-18 X 9/16" Blade Screw (1) 1/4-20 X 3/4" Hex Hd. Screw (1) 8-32 x 3/8" Flat Head Taptite T-15 (3) 10-24 X 1/2" Pan Hd. Taptite T-25 (15) 8-16 X .625 Pan Hd. Slotted Plastite T-20 (13) 8-16 X 2.25 Pan Hd. Slotted Plastite T20 (2) Warning Label, Inner Guard (1) Service Nameplate Kit (1) Armature (1) Field Assembly (1) Carbon Brush (2) Brush Holder (2) Cord (1) Fan (1) Brush Spring (2) Switch (1) Wire Assembly (Not Shown) (1) Gearcase (1) Collector Cover Plate (1) Collector Cover (1) Lower Guard (1) Fan Baffle (1) Motor Cover (1) Wire Cover (1) Handle Half, Left (1) FIG. 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 PART NO. 31-44-0215 31-44-0225 31-50-0015 31-52-0015 31-52-0040 34-60-0060 34-60-0400 40-50-0045 40-50-0315 40-50-0345 40-50-0355 42-38-0222 42-70-0050 42-96-0025 43-34-0090 43-34-0095 43-50-0015 43-54-0030 43-56-0015 43-78-0025 44-14-0015 44-20-0015 44-20-0050 44-52-0681 44-60-0105 44-60-1180 44-76-0210 44-86-0030 45-04-0485 06-75-3970 45-08-0015 45-08-0035 45-14-0020 45-16-0130 45-88-1545 49-96-0345 06-82-5560 DESCRIPTION OF PART Handle Half, Right Front Handle Motor Housing Depth Lever Lower Guard Lever External Retaining Ring E-Ring Spring, Guard Wrench Clip Spindle Lock Spring Torsion Spring Bumper Cover Clip Bearing Cup Inner Flange Outer Flange Glass Window Inner Guard Chip Guide Plate Hub Assembly Lower Guard Link Spindle Lock Latch Assembly Grip Front Latch Pin Pivot Pin Cord Protector Window Retainer Bumper Screw Bolt Depth Shaft Shaft Lower Guard Lever Lower Guard Sleeve Shoe Assembly Washer 6mm Hex Key 10-24 X 1/2" Truss Hd. Taptite T-25 NO REQ. (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) MILWAUKEE ELECTRIC TOOL CORPORATION 13135 W. LISBON RD., BROOKFIELD, WI 53005 Drwg. 2 Place spindle lock spring (41) into the spring retaining area on the gearcase (24), as shown. Press ball bearing (2) to the shoulder on the armature shaft (15). Orient the spindle lock (53) onto the armature shaft, inbetween the pressed on bearing and the front of the fan, as shown. Carefully insert the armature pinion/bearing into the gearcase. Align the spindle lock with the channel in the gearcase, making sure that the tab on the spindle lock engages the front of the spring. Orient the washer (66) such that the rounded edge is towards the depth rail of the shoe assembly (65). depth rail Verify that the hex head bolt (8) is fully seated in the gearcase (24) while assembling the depth shaft (62), as shown. Press the bearing (3) flush to .015" subflush to the gear cavity wall in the gearcase (24). Apply .320 - .360 oz. Type "Y" Grease, No. 49-08-5270, to gear bore of gearcase. The grease should be directed toward the pinion end of the armature. Orient the textured gripping surface of the lower guard lever (36) so it is parallel (±20°) with the back edge of the front handle (33), as shown. Functionally check the lower guard (27), with the saw set at full depth of cut. Place the saw upside down with the shoe (65) horizontal. Retract the lower guard 100%. Release the lower guard lever (36). The guard should return in a brisk manner. When tight, the depth adjustment lever (35) should be parallel (±20°) with the shoe (65).
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:05:05 13:16:07-05:00 Modify Date : 2008:06:20 14:03:19-07:00 Subject : 54-40-1625 Page Count : 2 Creation Date : 2003:05:05 18:16:07Z Mod Date : 2003:05:05 18:16:07Z Producer : Acrobat Distiller 5.0 (Windows) Author : pberger Keywords : Metadata Date : 2003:05:05 18:16:07Z Creator : pberger Title : 54-40-1625 Description : 54-40-1625EXIF Metadata provided by EXIF.tools