V43+_V43++_BIB_853B710B50_20100707 Mitsubishi Digital Electronics Home Theater System 838 738 BIB V3

User Manual: Mitsubishi Digital Electronics Home Theater System 838

Open the PDF directly: View PDF .
Page Count: 40

Download
Open PDF In Browser	View PDF

HOME-CINEMA TELEVISION
MODELS

738 Series
838 Series
BASIC OWNER’S GUIDE
This manual provides basic connection, setup, and operating instructions. Please visit our website at
www.Mitsubishi-tv.com to view or download a detailed owner’s guide that fully describes the features
of this TV. Follow the Support link to the Product Documents page.
•

•
•
•

For questions:
- Visit our website at www.mitsubishi-tv.com.
- E-mail us at MDEAservice@mdea.com.
- Call Consumer Relations at 800-332-2119 for operational or connection assistance.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
838 Series. IR emitter cables for NetCommand home-theater control are available for purchase from
Mitsubishi. Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part
number 299P254020 (four-ended cable).

CAUTION

FCC Declaration of Conformity

RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
Stand Requirement
CAUTION: Use these Mitsubishi TV models only with
the Mitsubishi stand models shown here. Other stands
can result in instability and possibly cause injury.
TV Model

Stand Model

WD-60738, WD-65738
WD-65838

MB-S60/65A

WD-73738
WD-73838

MB-S73A

82-inch TVs. Mitsubishi does not design, manufacture, or sell matching bases for 82-inch televisions
(WD-82738, WD-82838). When selecting a stand, base,
or other furniture to support the TV, please make sure it
is designed with the appropriate dimensions for stability and to support the TV’s total weight as well as the
weight of any additional equipment you plan to store.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.

For assistance call 1(800) 332-2119

Product:

Projection Television Receiver

Models:

WD-60738, WD-65738, WD-73738,
WD-82738
WD-65838, WD-73838, WD-82838

Responsible
Party:

Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904

Telephone:

(800) 332-2119

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.

WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.

Contents
1 Basic Setup and Operation
Remote Control . . . . . . . . . . . .
The STATUS Indicator . . . . . . . .
Setting Up and Using TV Inputs .
Basic TV Operation. . . . . . . . . .

. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .

2 TV Connections
Main Connection Panel . . . . . . . . . . . . . . .
838 Series Side Inputs . . . . . . . . . . . . . . .
Connection Types and Audio/Video Quality
HDMI Device . . . . . . . . . . . . . . . . . . . . . . . .
DVI Video Device . . . . . . . . . . . . . . . . . . .
Y Pb Pr Component Video Device . . . . . . .
Composite Video Device . . . . . . . . . . . . . .
Antenna or Cable TV Service . . . . . . . . . . .
VCR or DVD Recorder to an Antenna or
Wall Outlet Cable . . . . . . . . . . . . . . . . . .
A/V Receiver . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver with HDMI Output . . . . . . . . .

. . . .
. . . .
. . . .
. . . . .
. . . .
. . . .
. . . .
. . . .

. . . .
. . . .
. . . .

3 TV Features
FAV (Favorites) . . . . . . . . . . . . . . . . . . . . . . . .
ChannelView Channel Listings . . . . . . . . . . . . .
Photos and Moving Video as Composite Video .
3D Video . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Projector . . . . . . . . . . . . . . . . . . . . . . .
StreamTV™ Internet Media . . . . . . . . . . . . . . .
Wireless Audio Playback . . . . . . . . . . . . . . . . .
4 TV Menus
Picture. . . .
Sound . . . .
Captions . .
Setup . . . .
Inputs . . . .
Lock . . . . .

.
.
.
.
.
.

. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendices
Appendix A: TV Care
Lamp-Cartridge Replacement and Cleaning
Cleaning Recommendations . . . . . . . . . . .
Appendix B: Programming the Remote Control
Appendix C: Troubleshooting . . . . . . . . . . . . .

10
10
10
11
11
11
11
12
12
13
13

14
15
15
16
18
19
20

21
22
23
24
25
26

27
29
30
31

. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mitsubishi TV Software.
Warranty

6
7
7
9

Network Service Disclaimer

.
.
.

. . . . . . . . . . . . . . . .

For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION

Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
Internal Fans
Internal cooling fans maintain proper operating temperatures inside the TV. It is normal to hear the fans
when you first turn on the TV, during quiet scenes
while viewing the TV, and for a short time after shutting
off the TV. You may notice louder fan noise about 30
seconds after shutting off the TV and while using the
Bright Lamp Energy setting.
Lamp Replacement
For lamp-replacement instructions, see Appendix A .
To Order a Replacement Lamp Under Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available.
Important: All lamps replaced under warranty
must be returned to Mitsubishi where they will be
inspected to verify failure defects.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call (800)
553-7278. Order new lamp part number 915B441001.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be
covered by the warranty.
Children and TV Viewing
The American Academy of Pediatrics discourages
television viewing for children younger than two years of
age.

For assistance call 1(800) 332-2119

Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
1)

E XAMP LE OF ANT E NNA G R OUNDING

ANT E NNA
LE AD IN WIR E

Read these instructions.

2) Keep these instructions.

G R OUND C LAMP
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)

3) Heed all warnings.
4)

Follow all instructions.

5) Do not use this apparatus near water.

E LE C T R IC
S E R V IC E
E QUIP ME NT

G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)

6) Clean only with dry cloth.
7)

G R OUND C LAMP S

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.

NE C — NAT IONAL E LE C T R IC AL C ODE

P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)

Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.

Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.

11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

For assistance call 1(800) 332-2119

The following TV models are
ENERGY STAR® qualified:
WD-65738, WD-73738, WD-82738
WD-65838, WD-73838, WD-82838
Products that earn the ENERGY
STAR prevent greenhouse gas
emissions by meeting strict energy
efficiency guidelines set by the U.S.
Environmental Protection Agency
and the U.S. Department of Energy.

Basic Setup and Operation

Package Contents
Please take a moment to review the following list of
items to ensure that you have received everything.

Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by

Remote Control

gently pressing in the tab and lifting off the cover.

2. Load the batteries, making sure the polarities
Two AA Batteries

AA
AA

(+) and (-) are correct. For best results, insert
the negative (-) end first.
Snap the cover back in place.

Basic Owner’s Guide
1

The remote
control requires
two AA
batteries.

HDTV Quick Setup
Guide
2
Product Registration
Card
838 Series. Calibration
Microphone

First-Time Power-On
1. Press the

TV key to
ensure that the remote
control is in TV mode.

Before You Begin
1. Review the important safety, installation, and oper2.

ating information at the beginning of this book.
Choose a location for your TV.
•

•
•

Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV
as well as shortened lamp life.
Avoid locations where light may reflect off the
screen.
See the stand requirements on page 2.

3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.

2. Aim the emitter (bulb)
end of the remote control
at the TV and press the
POWER key
. Wait for the
Welcome screen.

3. If you wish to change the
menu language to Español,
press .

4. Press

to highlight EXIT.
Press ENTER to clear the
menu.

For assistance call 1(800) 332-2119

1. Basic Setup and Operation

Remote Control
Emitter End
TV CAB/SAT DVD AUDIO VCR
Press the key for the device type to
control. Leave in TV mode for normal
TV viewing.

Sleep Timer

Number/letter keys
Channel tuning, page 8
Pass code entry, page 26

Powers TV on or off.

Adds a separator in digital channel
numbers. Clears some menu entries.
MUTE

Mutes the TV speakers.

TOOLS

Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device.

LAST Returns to the previous channel.

FAV
FORMAT

Changes picture shape,
page 14

INTERNET

Connects to internet content
provided by VUDU™. See
page 19.

INPUT

Press to select a TV input.
See page 8.

VOL Controls volume of TV speakers.
CH
PAGE

Changes channels; moves to another
page in a menu or list.

ENTER Selects a channel number or menu item.

Navigation and adjustment
controls

GUIDE

ChannelView listings, page 15.

INFO

TV status or TV help.

Displays up to nine favorite
sources. See page 14.

AUDIO

Audio adjustments, page 22

VIDEO

Video adjustments, page 21

Displays or clears the TV main
menu (page 21). Also steps
back one menu.

EXIT

Clears all menus.

(PAUSE) Freezes a broadcast TV picture.
Record/Playback controls for external
devices. Additional setup is required.

The TV’s remote control can operate other
audio/video devices using any of these
methods:
• Program the remote control for the device (page
30).
• Set up HDMI Control for HDMI devices compatible with the TV.
• 838 Series. Perform NetCommand setup for
device keys.
See the detailed owner’s guide at
www.mitsubishi-tv.com for information.

For assistance call 1(800) 332-2119

838 Series. Special keys for use
with NetCommand IR control.
See the detailed owner’s guide at
www.mitsubishi-tv.com.

If You Turn Off the TV by Mistake
•
•

Press POWER again, within about 60 seconds, to
have the TV come back on immediately.
If the STATUS indicator is green and blinking rapidly,
(about 60 seconds after you shut off power), wait a
few moments for the indicator to stop blinking and
press POWER to turn the TV on again.

1. Basic Setup and Operation

Setting Up and Using TV Inputs

The STATUS Indicator
Key

Off
Slow Blinking

Steady On
Fast Blinking

LED Color TV Condition
None

TV is powered off. Normal operation.

Green

TV is powered on. Normal operation.

Green

TV powered off, auto-on TV Timer is
set.
Normal operation. TV can be turned on
at any time.

Green

TV just powered off and lamp is
cooling.
Sixty seconds after turning off TV, LED
will start to blink. TV can be turned back
on before blinking starts or after blinking stops, but not while the indicator is
blinking. Normal operation.

Yellow

Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 12.
You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in the local area.
Memorizing Channels with Channel Scan
For the ANT input
To start channel memorization
1. Power on the TV.

2. Press MENU and open the Setup > Channel menu.
First press to navigate to the Setup icon, then
use to highlight the Channel icon.

TV is too hot. The TV will display a
warning message and shut off if it overheats.
•

•

Ambient room temperature may be
too high. Turn off the TV and let the
room temperature drop.
Clear blocked air vents. Ensure at
least a four-inch clearance on all
sides of the TV.

Yellow

Lamp access door is not secure or no
lamp installed.
TV will not operate until lamp access
door is secured. See Appendix A .

Red

Lamp failure. Replace the lamp. See
Appendix A .

Red/
Yellow

TV may require service.
• Hold power button on front panel for
10 seconds to reset TV.
• If LED continues to flash red and
yellow after reset, turn off the TV and
unplug it from the AC power source.
Wait one minute and then plug the
set back in.
• If LED continues to flash red and
yellow, go to www.mitsubishi-tv.com
or call 1-800-332-2119 to receive
Authorized Service Center information.

Start channel memorization from the Setup > Channel
menu.

3. Press to enter the menu.
4. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a
check.

5. For first-time setup, highlight All
channels. To scan for channels not
already in memory, highlight New
only. Press ENTER to add a check.

6. Highlight Scan and press ENTER.
Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.

You may be asked to count how
many times the LED flashes each
color to aid in troubleshooting.

For assistance call 1(800) 332-2119

1. Basic Setup and Operation

Setting Up and Using TV Inputs, continued
Setting Up Other Inputs
1. Power on the TV.
2. Power on the devices to ensure detection.
3. Connect one device to the TV, making note of the

TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
Highlight the device type in the on-screen list and
press ENTER. The name you select here will appear
in the Input Selection menu.

Selecting an Input to Watch

1. Press INPUT.

Sample Input Selection menu, antenna input selected

2. Press
to highlight an input icon.
3. Press ENTER to switch to the input.
Tuning to Channels on the Antenna Input
•
•
Sample New Device
Found screen.

5. Press EXIT to close the New Device Found screen.
6. Repeat steps 3 through 5 for each additional device
you want to add.

About Auto Input Sensing
This TV’s Easy Connect™ Auto Input Sensing
feature detects most input connections automatically. Some exceptions are:
• A connection on the ANT input
• TV audio outputs (analog and digital)
• An HDMI-equipped device that is powered off.
Power on the device first to ensure detection.
• Ethernet
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly
detected devices.

For assistance call 1(800) 332-2119

•
•

Enter the channel number using the number keys
on the remote control and press ENTER.
For a two-part digital channel, such as 3-1, press 3
—
CANCEL .
Press CH
/
to change channels one channel at
a time.
Press and hold CH
/
to speed through channels.

•
•

Press LAST to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to nine
favorite channels. See page 14.

•

Press GUIDE to display ChannelView channel listings,
highlight a channel number, and press ENTER to tune.

1. Basic Setup and Operation

Basic TV Operation
Picture Settings

Changing Audio Settings (TV Speakers Only)

1. To get the best picture under different viewing con-

1. Press AUDIO.
2. Press to display the name of the adjustment you

ditions, set the Picture Mode first before changing
other video settings. See page 21 for a description
of the options.

want. See page 22 for descriptions.
to change.

3. Press

Controlling Sound Volume
a. Press VIDEO.
b. Press until the Picture Mode
option displays.

•
•

c. Press

to make one of these selections:

Name
Brilliant
Game
Bright
Natural

When to Use
Under bright light
With gaming consoles (inputs
named Game or PC only)
For most daytime viewing
For most nighttime viewing

2. Press to display the name of another adjustment.
3. Press
to make the adjustment.
4. Wait a few seconds and the display will clear.
Additional picture options are available through the following menus:
Menu

Page

Picture > Picture Plus

Picture > Perfect (838 series)

Picture > 3D Mode

Audio Controls
Changing the Audio Output
To switch from the internal TV speakers to an external
sound system:

1. Press AUDIO.
2. Press to display the
3.

TV Speakers option.
Press
to change.

Press VOL
/
to adjust the
sound level of the TV speakers.
See the full owner’s guide at
www.mitsubishi-tv.com for
methods of controlling A/V receiver
volume.

More TV Features
Features covered in this Basic Owner’s Guide include:
Feature

Page

Parental controls (Lock menu)

TV Clock. Set the TV Clock if you plan to use
the TV Timer (page 24) or ChannelView (page
15).

Favorite sources

ChannelView and custom channel collections

Changing the input names that appear in the
Input Selection menu (Inputs > Name menu)

3D Video

Internet video streaming with VUDU

Digital camera images as composite video

838 Series. Listening to a wireless audio
device with the TV speakers

See the detailed Owner’s Guide at
www.mitsubishi-tv.com for more on the features
described here and to learn about other features,
including:
• HDMI control (CEC) of other A/V devices
• 838 Series. NetCommand IR control of other A/V
devices. Use of NetCommand requires purchase of
IR emitter cables available from Mitsubishi.
• 838 Series. Center and rear channel audio output
• 838 Series. Using an external subwoofer.
• 838 Series. Viewing photo files from a USB device.

For assistance call 1(800) 332-2119

TV Connections

Main Connection Panel

838 Series Jacks. See
the full owner’s guide at
www.mitsubishi-tv.com.

DIGITAL
AUDIO
OUTPUT
(page 13)

SUB
WOOFER
OUTPUT

CENTER
INPUT

AUDIO
OUTPUT
(page 13)

DVI/PC AUDIO
INPUT
page 11

DIGITAL
AUDIO
OUTPUT

DVI/PC AUDIO
R INPUT L

AUDIO
OUTPUT

AUDIO/SURROUND
OUTPUT
(838 series, page 23)
AUDIO/SURROUND
R OUTPUT L

ANT
AN
T
L

Y/ VIDEO

HDMI

LAN

3
Y/ VIDEO
R AUDIO

USB
(Accessory power
on all models;
738 Series, wireless
adapter, page 19)

HDMI
page 11

LAN
(Ethernet, port
page 19)

VIDEO
R&L
Y Pb Pr
Analog (composite (component
video)
Audio
video)
Input

ANT
page 12

3D GLASSES
EMITTER
(page 16)

Auto Input Sensing
The TV’s Auto Input Sensing
feature automatically recognizes many connections and
prompts you to identify the
type of device connected.
See page 8 for more on Auto
Input Sensing.

INPUT 3
Pb

3D
GLASSES
EMITTER

Pb
Pr
(480i / 480p / 720p / 1080i)

838 Series Side Inputs
Pr

INPUT 2

IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT

INPUT 1

Y/ VIDEO

L AUDIO R

Y Pb Pr
VIDEO
(component (composite
video)
video)

R&L
Analog
Audio
Input

USB

USB
(page 19)

HDMI 4

HDMI

Connection Types and Audio/Video Quality
VIDEO QUALITY

BEST
HDMI

HDMI-to-DVI

AUDIO QUALITY

GOOD
Component
Video

For assistance call 1(800) 332-2119

Composite
Video

BEST
HDMI

GOOD
Digital
Audio

L/R Analog
Audio

2. TV Connections

HDMI Device

Y Pb Pr Component Video Device

Mitsubishi recommends using high-speed HDMI
cables to connect newer devices incorporating HDMI
technology.
AUDIO
OUTPUT

Y/ VIDEO

HDMI
2

DIGITAL
AUDIO
OUTPUT

3D
GLASSES
EMITTER

INPUT 1

ANT

DVI/PC AUDIO
R INPUT L

Y/ VIDEO
DEO
L

Y/ VIDEO

HDMI

Pb
Pr
(480i / 480p / 720p / 1080i)

ANT

DVI/PC AUDIO
R INPUT L

LAN

3D
GLASSES
EMITTER

INPUT 1

R AUDIO

AUDIO
OUTPUT

INPUT 2

DIGITAL
AUDIO
OUTPUT

Required:
• RCA-type component video cables
• Left/right analog audio cables.

Y/ VIDEO
R AUDIO

Pb
Pr
(480i / 480p / 720p / 1080i)

TV main panel
HDMI-to-HDMI
cable

TV main panel

Y/ VIDEO

R– AUDIO –L

Any HDMI device

Component
video cables

Audio
cables

HDMI and Digital Surround Sound
738 Series. The TV’s HDMI inputs can receive
digital stereo audio signals only when using the TV
speakers.

Incoming from
cable service or
satellite dish

838 Series. The TV’s HDMI inputs can receive
digital surround sound from an HDMI device. Use an
HDMI connection if you want to hear digital surround
sound from the TV’s internal speaker array.

DVI Video Device

L
R
AUDIO

CABLE IN or
SATELLITE IN

Component video
device

Composite Video Device

Required:
• DVI-to-HDMI cable or DVI/HDMI adapter and
HDMI cable
• Left/right analog audio cables

Required:
• Composite video cable (usually yellow)
• Analog stereo audio cables.
DIGITAL
AUDIO
OUTPUT

DVI/PC AUDIO
R INPUT L

Y/ VIDEO

LAN

DVI/PC AUDIO
R INPUT L
Y/ VIDEO
R AUDIO

Y/ VIDEO

GLASSES
R– AUDIO
–L
EMITTER
INPUT 1

INPUT 2

ANT

DVI/PC AUDIO
R INPUT L

LAN

3D
GLASSES
EMITTER

Y/ VIDEO
R AUDIO

INPUT 1

Y/ VIDEO

AUDIO
OUTPUT

ANT

AUDIO
OUTPUT

HDMI

INPUT 2

DIGITAL
AUDIO
OUTPUT

HDMI

Pb
Pr
(480i / 480p / 720p / 1080i)

Pb
Pr
(480i / 480p / 720p / 1080i)
L

TV main panel
TV main panel
L

DVI OUT

DVI-to-HDMI
cable

R
L

Audio
cables

AUDIO OUT

COMPOSITE
VIDEO OUT

AUDIO

Digital DVI
device

Audio
cables

Composite
video cable

VCR or other device with
composite video output

For assistance call 1(800) 332-2119

2. TV Connections

Antenna or Cable TV Service
Connect the incoming cable to the TV’s ANT input.

Antenna
Direct cable (no cable box)
or

Cable TV
service

VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Required:
1. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Two coaxial cables

OUT

Older cable box
Not recommeded. Other
connection types provide
better quality audio and video.

Note: If your recording device has an analog-only
tuner, you must use a digital converter box to
enable recording of digital broadcasts.

ANT

DIGITAL
AUDIO
OUTPUT

TV main panel

AUDIO
OUTPUT

Y/ VIDEO

ANT

DVI/PC AUDIO
R INPUT L

3D
GLASSES
EMITTER

INPUT 1

LAN

INPUT 2

DIGITAL
AUDIO
OUTPUT

AUDIO
OUTPUT

Y/ VIDEO

ANT

DVI/PC AUDIO
R INPUT L

R AUDIO

Pb
Pr
(480i / 480p / 720p / 1080i)

3D
GLASSES
EMITTER

INPUT 1

INPUT 2

ANT
Y/ VIDEO

LAN

Y/ VIDEO

Pb
Pr
(480i / 480p / 720p / 1080i)

Composite
video cable

Y/ VIDEO
R AUDIO

1b.

1a.

ANTENNA
IN
L
R
AUDIO OUT

COMPOSITE
VIDEO OUT

COMPONENT
VIDEO OUT

DVD Recorder or VCR
3.
RF Splitter

Incoming cable
4.

For assistance call 1(800) 332-2119

2. TV Connections

A/V Receiver

A/V Receiver with HDMI Output

Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below.
The TV makes all audio available in digital and analog
formats:
• Analog audio coming into the TV is available as
output in digital stereo format on the DIGITAL
AUDIO OUTPUT jack.
• Digital incoming audio is available as analog output
on the AUDIO OUTPUT L and R jacks.

Y/ VIDEO

AUDIO
OUTPUT

ANT
L

3DAUDIO
R GLASSES
EMITTER
OUTPUT

DIGITAL
AUDIO
OUTPUT

DVI/PC AUDIO
R INPUT L

INPUT 1

DIGITAL
LAN
AUDIO
OUTPUT

838 Series: This setup allows you to use NetCommand-controlled audio and video switching
over the HDMI cable. See the full owner’s guide at
www.mitsubishi-tv.com for details.

Y/ VIDEO
R AUDIO

Y/ VIDEO

Pb
Pr
(480i / 480p / 720p / 1080i)

HDMI
2

Y/ VIDEO
R AUDIO

Stereo analog
cables (for an
analog A/V
receiver)

ANT

AUDIO
OUTPUT

3D
AUDIO
R GLASSES
EMITTER
OUTPUT

DIGITAL
AUDIO
OUTPUT

LAN

TV main panel
Digital coaxial
cable (for a digital
A/V receiver)

INPUT 2

This option allows you to view content from devices
connected to an A/V receiver. The A/V receiver can
send audio and video to the TV over a single HDMI
cable. You can use an HDMI connection as described
here in addition to an audio connection from the TV’s
audio output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to
the TV only, e.g., an antenna on the ANT input.

INPUT 1

DVI/PC AUDIO
R INPUT L

INPUT 2

DIGITAL
AUDIO
OUTPUT

Required: One HDMI-to-HDMI cable

Pb
Pr
(480i / 480p / 720p / 1080i)

Optional
analog or
digital audio
connection

HDMI cable

OPTICAL
INPUT
COAXIAL
INPUT

A/V receiver back panel
Note:
•

•

On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use
the connection for an analog A/V receiver.
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and
analog stereo sound from the TV.

A/V receiver with
HDMI output

HDMI OUT

DIGITAL
AUDIO IN

Any connection
types
High-definition
DVD player

ANALOG AUDIO IN

VCR

DVD player
Cable box

For assistance call 1(800) 332-2119

TV Features

The FORMAT Key and Picture Shape
Repeatedly press the
FORMAT key to cycle
through displays available for the current
program. The TV will
remember the format
you last used on each
input.
Important
Black bars at the edges of the
picture are common in HD
pictures. Black bars are not a
defect of the TV.
• Black bars are added by broadcasters to fill the 16:9 screen
area while preserving the original
aspect ratio of the picture.
• Your cable box or satellite
receiver may also be altering
the broadcast picture. If your
receiver offers output in native
format, try using it with Mitsubishi’s picture formats.

Sample Uses of the FORMAT Key
You can use the FORMAT key to reduce or eliminate black areas at the
edges of the picture.

Press

Squarish 4:3 image is
narrower than the 16:9
screen; unused areas at the
sides are filled with black.

Wide Expand mode stretches
the picture sideways to fill the
screen.

Press

Wide 2.35:1 anamorphic DVD
image; unused areas at the
top and bottom are filled with
black (letterbox effect).

Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.

Sample Favorites menu. Switch to favorite channels or
inputs using number keys.

For assistance call 1(800) 332-2119

1. Press INPUT and switch the TV to the input
you want to add. If adding a channel, switch
to the ANT input and tune to the channel.
2. Press the FAV key.
3. Move the highlight to the number position
you want to assign to the channel or input.
4. Press ENTER.

Removing

The FAV key gives you quick access to favorite program
sources. Sources can be channels from the ANT input
or devices connected to the TV. You can store up to
nine favorites.

Adding

FAV (Favorites)

1. While watching TV, press the FAV key.
2. In the Favorites menu, highlight the channel
or input you want to remove.
3. Press CANCEL.

Selecting

1. While watching TV, press the FAV key.
2. Press the number key for the channel or
input you want.

3. TV Features

ChannelView Channel Listings
ChannelView displays program descriptions sent by
broadcasters. This information may be unavailable
in some areas.

to highlight a bank.
3. Press
4. Press MENU to see channels in the bank.
To allow tuning to any channel in memory, select
the All bank.

•

About ChannelView
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program information
for digital channels. No program information is displayed
for analog channels.
ChannelView allows you to set up three banks of custom
channels for convenient access. You can save groups of
channels by content (e.g., news, sports, children’s programming) or by TV user.
Note:

You must first set the TV Clock (page 24) to
receive ChannelView listings.

Photos and Moving Video as
Composite Video
Note:

838 series TVs can display photos and play music from a USB drive. See the detailed owner’s
guide at www.mitsubishi-tv.com.

Connect the camera to the TV using a composite video
cable and control the slide show or movie through the
camera. The display resolution will be standard-definition (480i).

1. Refer to the owner’s manual supplied with the
camera for instructions needed for this setup.

2. Set the camera’s output signal type to NTSC and
3.

ChannelView, “All” tab. Programs for the tuned channel
are listed on the right.

put the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the TV’s Y/VIDEO jack. To hear audio, connect the
camera’s audio output cable to the AUDIO L jack.
INPUT 3
Pr

Y/ VIDEO

L AUDIO R

USB

HDMI 4

ChannelView Custom Channel Banks

Optional
Audio Cable

Select a channel bank to customize.

1. Press GUIDE to display ChannelView.
2. Press MENU to move the highlight to the bank
3.
4.
5.

header.
Press
to select Bank 1, 2, or 3.
With the bank name highlighted, press ENTER to
enter setup mode where you can select channels to
include in the bank.
Press EXIT when finished with setup.

Camera connection using a composite video cable

4. When the New Device Found screen displays,
assign the name Camcorder.

5. Press EXIT to close the New Device Found screen.
6. Highlight the icon for the camera input and press
ENTER.

Using Custom Channel Banks
•
•

While watching TV, press CH
/ . The TV will
tune only to channels stored in the current bank.
To change to a different channel bank:
1. Press GUIDE.

7. If viewing photos, control the slideshow from the
camera. Advance through the images manually or
check if the camera can advance automatically.

2. Press MENU.

For assistance call 1(800) 332-2119

3. TV Features

3D Video
To display 3D gaming or 3D cinema content, your
Mitsubishi TV requires:
• A compatible 3D source device outputting a 3D
signal in one of these formats:
- Checkerboard format, 1080p, 60-Hz; (lower
resolutions may be supported but will not fill the
screen)
- Side-by-Side format, 1080p, 24/30/60 Hz; 720p,
60 Hz
• Active-shutter 3D glasses, DLP link type or IR
emitter type with matching emitter
Please visit our website at www.mitsubishi-tv.com for information about future TV software updates that will broaden
3D signal compatibility.

Watching 3D Video
Note:

1. Press INPUT.
2. Highlight the icon for the 3D video device and press
3.
4.
5.
6.

Initial Setup
1. If your 3D glasses came with an emitter box,

Active 3D glasses are required.

ENTER.
Press MENU and select the Picture > 3D Mode
menu.
Select On for 3D Mode. The On setting will be
memorized for the current input when you exit this
menu.
Select the Source Format. If your source device
outputs an unsupported signal format see “Notice
Concerning Format Compatibility” on this page.
For Glasses Control, select the control type for
your 3D glasses, either IR Emitter or DLP Link.

connect the emitter box to the 3D GLASSES
EMITTER jack. Place the box in front of the TV
where there is a clear path to the glasses.
Note:

If your glasses are marked DLP Link, skip this
step; no emitter box is required with DLP Link
technology.
CENTER
INPUT

SUB
WOOFER
OUTPUT

DIGITAL
AUDIO
OUTPUT

AUDIO
OUTPUT

ANT

DVI/PC AUDIO
R INPUT L

Y/ VIDEO

HDMI
2

LAN

3D
GLASSES
EMITTER

INPUT 1

INPUT 2

IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT

Y/ VIDEO
R AUDIO

Pb
Pr
(480i / 480p / 720p / 1080i)

3D
GLASSES
EMITTER

Use the Picture > 3D Mode menu to enable 3D video.

2. Power on the TV and the source device.
3. Connect the source device to the TV’s HDMI input.
4. When the New Device Found screen displays,
5.

name the input.
Press EXIT to close the New Device Found screen.

7. Press EXIT to close the menu.
8. If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Picture > 3D Mode menu and set Glasses L-R to
Reverse.

To Watch Regular (non-3D) Video
The 3D Mode setting is memorized for each input.
When you want to watch non-3D video on the input
selected above, open the Picture > 3D Mode menu
and set 3D Mode to Off.
Notice Concerning Format Compatibility
Mitsubishi 3DTVs (738 and 838 series) currently support
the side-by-side 3D signal format. For support of other 3D
formats, such as top-bottom and frame packing (3D Blu
Ray standard), Mitsubishi 3DTVs will require the use of a 3D

For assistance call 1(800) 332-2119

source device that outputs the 3D checkerboard format or
a 3D source device coupled with the Mitsubishi 3D adapter.
In all cases an emitter and matching 3D active shutter
glasses or DLP Link active shutter glasses are required in
order to view 3D content.

3. TV Features

3D Video, continued
3D Safety Requirements
•

3D Glasses are NOT designed as sunglasses or
safety glasses and do not provide protection. 3D
glasses should be worn only when viewing 3D
material.
• Do not wear the wireless glasses in any situations
that require unimpaired visual perception.
• Children under the age of 5 should not view 3D
programming.
Under normal conditions, 3D viewing is safe for your
movies or games. Some people may experience discomfort, however. To minimize the potential for experiencing visual problems or any adverse symptoms:
• Read and follow any and all safety warnings that
accompany your 3D glasses or 3D source devices.
• Maintain a distance of no less than 2 to 2.5 times
the screen height measurement away from the
display. Viewing from too short a distance can
strain your eyes.
• Take regular breaks, at least 5 minutes after every
hour of 3D viewing.
If you experience any of the following symptoms, discontinue 3D viewing until the symptoms go away:
• nausea, dizziness, or queasiness,
• headache, or eyestrain,
• blurry vision,
• double vision that lasts longer than a few seconds,
Do not engage in any potentially hazardous activity
(for example, driving a vehicle) until your symptoms
have completely gone away. If symptoms persist,
discontinue use and do not resume 3D viewing without
discussing your symptoms with a physician.
Do not use the glasses where loss of balance or limiting your field of vision may be dangerous to you.
Do not use near staircases, ledges or balconies. You
may risk falling during or after use.

Epilepsy
WARNING! IF YOU OR ANY MEMBER OF YOUR
FAMILY HAS A HISTORY OF EPILEPSY, CONSULT
A PHYSICIAN BEFORE USING 3D VIDEO OR GAME
PRODUCTS.
A small percentage of the population may experience
epileptic seizures when viewing certain types of TV
images or video games that contain flashing patterns of
light.
The following people should consult a physician before
viewing 3D Games or Video:
• Anyone with a history of epilepsy, or who has a
family member with a history of epilepsy
• Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing
light effects.
WARNING! SOME LIGHT PATTERNS MAY INDUCE
SEIZURES IN PERSONS WITH NO PRIOR HISTORY
OF EPILEPSY. DISCONTINUE 3D VIEWING IF YOU
EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:
• Involuntary movements, eye or muscle twitching
• Muscle cramps
• Nausea, dizziness, or queasiness
• Convulsions
• Disorientation, confusion, or loss of awareness of
your surroundings
Do not engage in any potentially hazardous activity (for
example, driving a vehicle) until your symptoms have
completely gone away.
Do not resume 3D viewing without discussing the
symptoms with your physician.

For assistance call 1(800) 332-2119

3. TV Features

Sound Projector
838 Series
The TV’s built-in speaker array can be set up to reflect
sound off the room walls to create a surround sound effect.

3. Place the microphone as described in the guide4.

lines.
Press MENU and go to Sound > AutoSP.

Positioning the TV
•
•

Center the seating area in front of the TV and at
least six feet away.
Arrangements that give good results:

5. Highlight START and press ENTER.
6. Quietly exit the room right away. The calibration
•

If the room is an odd shape, locate the TV to take
best advantage of wall reflections.

sequence may be loud. Wait for completion of setup
before returning to the room.
Play some sample audio material to check the
sound quality.

Note:

Do not perform manual adjustments after running auto setup as doing so will delete all autosetup results.

8. Store the microphone out of direct sunlight and
away from heat.
•

Avoid locations that may distort sound reflections.

Microphone Placement
TV
6 ft. minimum

Connecting the TV
To hear digital surround sound, the TV must be connected to a digital surround sound source. The surround
sound source can be on an HDMI input or the ANT input
(for some digital broadcasts). Other stereo connections
will provide Dolby Pro Logic surround sound.

Microphone
Set the microphone
on a level surface at
ear height at least
six feet from the TV.
Use a seat backrest
or tripod so as to
pick up sound from
all directions.

Maximum height above speakers

Auto Setup
Auto setup uses the included calibration microphone. For manual setup, see the full owner’s guide at
www.mitsubishi-tv.com.
1. Power on the TV and external subwoofer, if any.

2. Plug the microphone cable into the TV’s INPUT 3

Height of TV
speakers

3 ft.

Be sure the
height of the
microphone is
within three feet
of the speaker
height.

left audio jack.
L AUDIO R

For assistance call 1(800) 332-2119

Microphone
Center the microphone in front of
the TV.

3. TV Features

StreamTV™ Internet Media
Internet services provided by VUDU™ Apps let you
access many popular on-line applications. In addition to
free content, VUDU’s movie service lets you buy and rent
movies through the TV. Visit www.VUDU.com to learn
more about available movie titles, prices, and services
offered. For a list of recommended routers and switches,
see the Support > FAQ section at VUDU.com.

Required for StreamTV internet media:
•
•
•
•

Broadband internet service (at least 2 Mbps for SD, 4 Mbps
for HD, and 8 Mbps for 1080p HDX)
Ethernet cable or an Azurewave AW-NU231 USB
wireless adapter.
Computer access to the VUDU.com website (required
for initial account activation).
A credit card for rental and purchase transactions
from VUDU’s movie service.

Home Network Setup
Before using StreamTV internet media, you must connect
the TV to the internet using one of these methods.
Ethernet Connection
DHCP (automatic)
1. Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
SUB
WOOFER
OUTPUT

DIGITAL
AUDIO
OUTPUT

AUDIO
OUTPUT

ANT

AUDIO/SURROUND
R OUTPUT L

LAN

IR-NetCommand
Output/EXTERNAL

Y/ VIDEO

Setup > Network menu
3D
GLASSES
EMITTER

INPUT 1

LAN

INPUT 2

CENTER
INPUT

Y/ VIDEO
R AUDIO

Pb
Pr
((480i / 480pp / 720pp / 1080i))

connect. A check will appear next to the connected
network.

TV Main Panel
Router or modem
Incoming providing high-speed
internet
internet service
cable

4. Highlight the desired network and press ENTER to

Ethernet
cable

2. Open the Setup > Network menu to review settings.
3. Press EXIT to clear the menu.
Manual

Setup > Network menu after connecting. The active
network is checked and connection data displays.

1. Connect the TV to your network router with a Cat-

Y/ VIDEO

HDMI

LAN

INPUT 2

3.
4.
5.

3D
GLASSES
EMITTER

INPUT 1

5. If connecting to a secure network, enter the
egory-5 Ethernet cable (not supplied).
network key or password on the remote control
In the Setup > Network menu, highlight Manual and
when prompted.
press ENTER.
Press to move to the Connection Data area.
Input the connection data.
After entering connection data, press ENTER to
IEEE 802.11n-compliant
wireless network router
connect.
Back of 738
providing
Change any of the following if needed:
Wireless
Series TV
high-speed
adapter
• Default Gateway
internet service
• DNS
OR
• Subnet Mask
Y/ VIDEO

R AUDIO

Pb
Pr
((480i / 480pp / 720pp / 1080i))

INPUT 3

Wireless Connection

1. Disconnect the Ethernet cable if present.
2. Connect an Azurewave AW-NU231 USB wireless
3.

adapter to the TV’s USB port.
Open the Setup > Network menu. After a few
seconds, detected networks will appear listed on
the screen in order of signal strength.

Y/ VIDEO

L AUDIO R

USB

HDMI 4

Incoming
internet
cable
Wireless
adapter

838 Series
TV
Connecting the USB wireless adapter

For assistance call 1(800) 332-2119

3. TV Features

StreamTV™ Internet Media, continued

838 Series. The TV’s built-in speaker array can play
audio from a handheld device using Bluetooth® A2DP
(stereo audio) wireless technology.

Using StreamTV Internet Media
After establishing internet connectivity, press the INTERNET key to display
services from VUDU Apps. Press
ENTER to launch an application.

Wireless Audio Playback

INTERNET

Getting Started with VUDU
Movies
1. After establishing internet connectivity, press

Pairing the TV with an Audio Device
1. Turn on the wireless device you wish to use for play2.

back. Turn off all other wireless devices in the area as
the TV can pair with only one device at a time.
Press INPUT to display the Input Selection menu.

INTERNET to display offerings from VUDU.
Select the VUDU movie service.

2.
3. Browse the VUDU movie catalog and offerings.
4. When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A
credit card is required for activation.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.

Bluetooth® icon in Input Selection Menu

3. Highlight the Bluetooth icon and press ENTER.
4. Pair your device with the TV and then connect.

Specialized Keys for VUDU
INTERNET

Some devices pair and connect automatically,
while others require you to enter the TV pass code
displayed.
Use keys on the TV’s remote control to control playback. Not all keys work for all devices.

Displays the VUDU internet menu.

(PAUSE)
Skip a track

(STOP)

GUIDE

VUDU HOME key

INFO

VUDU MORE key

(REVERSE)

LAST

VUDU BACK key (goes to previous menu)

(PLAY)

CANCEL

VUDU backspace (in text-entry screens)

(FORWARD)

F2
EXIT

VUDU System menu
Exit VUDU

Troubleshooting

Resetting Bluetooth Pairing or Connection
Perform this reset if the audio device does not connect
properly to the TV.

If You Are Unable to Connect to the Internet
• Check all power and data connections.
• If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
• If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.

1. If the audio device has been previously paired with

For Further Assistance
• If you are having trouble connecting your TV or
accessing internet applications, contact Mitsubishi
Customer Care at 1-800-332-2119.
• If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
• See more troubleshooting tips in Appendix C.

•

For assistance call 1(800) 332-2119

the TV, delete the TV from the device’s paired list.
Go to the TV’s Inputs > Name menu and highlight
the Bluetooth icon. Press ENTER to select Off.
Press EXIT.

3.
4. Go to the Inputs > Name menu and highlight the
5.

Bluetooth icon. Press ENTER to select On.
Press EXIT.

Tips for Wireless Playback

•
•
•

Selecting the Bluetooth icon at a later time will
reconnect the TV to the paired device.
If the paired device is not available, the TV will
accept pairing from a different device.
Once connection is lost, the TV will power off after
five minutes without receiving a signal.
To clear a paired device, turn off the Bluetooth icon
(Inputs > Name menu) or pair the TV with a different device.

TV Menus

Press MENU on the remote control to open the main menu and access these settings.

Picture
Picture

Video

Settings in this menu are saved for the current input only. To make picture adjustments:
From the Picture > Video menu
1. Press
to highlight an option
2. Press
to adjust.

Picture
Mode

While watching TV
1. Press the VIDEO key.
2. Press
to select a video option.
3. Press
to change the setting.

Brilliant

For use under bright light.

Game

Optimizes picture and video processing for game consoles.
Available only when the input name is Game or PC.

Bright

For most daytime viewing

Natural

For most nighttime viewing

Set the Picture Mode
before changing other
video settings, Use Picture
Modes to get the best
image under different
viewing conditions.

Advanced Modes. Contact your professional installer for setup.
Contrast

In most home lighting situations, medium contrast looks best. Stored for each Picture Mode.

Brightness

Adjusts overall picture brightness. Stored for each Picture Mode.

Color

Adjusts overall color intensity from monochromatic to fully saturated. Saved by input.

Tint

Adjusts the red-to-green ratio. Saved by input.

Sharpness

Adjusts picture detail and clarity. Saved by input.

Color Temp)

High gives white a cool cast. Low gives white a warm cast. Stored for each Picture Mode.

Video Noise

Reduces minor noise (graininess) in the picture. Saved by input.

EdgeEnhance

EdgeEnhance™ makes the image appear sharper. Saved by input.

DeepField
Imager

Provides strong contrast with detail over mixed screen content. Demo displays a split picture to
show On (right side) and Off (left side). Saved by input.

Picture

Picture+ (Picture Plus)

Screensaver Displays a screensaver pattern while playing an audio-only source.
Film Mode

480i and 1080i signals only. In Auto, the TV automatically detects and applies film-decoding correction to movies filmed at 24 frames per second. Try the Off setting if images show many jagged edges.
Setting saved by input.

Smooth 120 Smooth 120 reduces motion blur in action scenes but may show pixel structure during slower motion or in still
images. Works in conjunction with Film Mode.
Test
Picture

Displays a test picture.

For assistance call 1(800) 332-2119

4. TV Menus

Picture, continued
Picture

Reset
•
•

Picture

Resets sound and picture adjustments for the current input. Highlight the Reset icon
and press ENTER twice to perform reset.
Reset has no effect on universal settings (Balance, Listen To, Language) or on
Advanced picture settings.

Perfect
(PerfectColor/PerfecTint) 838 Series. Sliders let you adjust the saturation (intensity) and
hues of six separate colors for the current image source.

Picture

Advanced
Advanced Modes. Contact your professional installer for setup.
738 Series. Special/ADV.
838 Series. ISF Day/ADV1, ISF Night/ADV2

Picture

3D Mode
See page 16.

Sound
Sound

Audio

Settings in this menu are saved for the current input only. To make audio adjustments:
From the Sound > Audio menu
1. Press
to highlight an option
2. Press
to adjust.

TV Speakers
(sound source)

While watching TV
1. Press the AUDIO key.
2. Press
to select an audio option.
3. Press
to change the setting.

Turns on the internal TV speakers.

Off

Turns off the internal TV speakers so you hear sound only through a connected device
(A/V receiver or headphones).

Center

838 Series. Makes the TV’s speaker array act as a center channel. See the
detailed owner’s guide at www.mitsubishi-tv.com for use of this feature.
838 Series. Adjusts the volume level of a connected subwoofer. Set Sound >
Global > Subwoofer to On to make this adjustment available.

Subwoofer

[Subwoofer
level adjustment]

Bass

Controls bass sound from the TV speakers.

Treble

Controls high-pitched sound from the TV speakers.

Balance

Controls audio balance between the right and left TV speakers (Sound Mode Stereo only)

Sound Mode

Stereo

No special audio effects from the TV speakers

Surround

Modifies audio from the TV speakers.
• For monaural (non-stereo) programs, creates a simulated stereo effect.
• For stereo programs, creates a simulated surround sound effect.
• 838 Series. The TV’s speaker array plays surround sound if available.

Music

838 Series. Optimizes the TV’s speaker array for music listening.

Night

838 Series. Focuses the TV’s speaker array to a single point to limit sound heard
by others outside the room. Press ENTER to adjust the focal point (Night Angle).

For assistance call 1(800) 332-2119

4. TV Menus

Sound, continued
Level Sound

On, Off

Reduces differences in sound volume between programming segments.

Analog Listen To Stereo
(For antenna
SAP
analog channels)
Mono

Sound

The TV plays stereo broadcasts in stereo and mono broadcasts in mono.
Second Audio Program. Selects an additional monaural sound track.
Reduces background noise. Use when receiving a weak stereo audio signal.

Global
838 Series. Settings in this menu apply to all inputs.

Analog Audio
Out

These settings affect audio from the AUDIO/SURROUND OUTPUT jacks.
Fixed

Use with an analog A/V receiver.

Variable

Use with headphones; adjust headphone volume using the TV’s remote control.

Rear

838 Series. Use when supplementing the TV’s speaker array with external rear speakers.

Subwoofer

Select On to turn on audio to a connected subwoofer. Set to Off if no subwoofer is connected.

Center Channel

On allows the TV’s speakers to complement your external sound system as a center channel. Set
to Off if not in use.

Sound

Auto Sp
838 Series. See page 18 for setup instructions.

Sound

SoundPro
838 Series. Lets you set up the Sound Projector speaker array manually. See the
detailed owner’s guide at www.mitsubishi-tv.com.

Captions
Captions

Services

Service

On if Mute: Displays digital closed-caption signal Caption 1 (digital) or CC1 (analog) when audio from the
TV speakers is muted. While watching TV, press MUTE to turn closed captions on/off.

Digital

Caption 1–Caption 6: Caption signals sent by the broadcaster.

Analog

•
•

Captions

CC 1–CC 4. Standard closed-caption signals
Text 1–Text 4. Text-service signals

Font
As Broadcast changes settings to those selected by the captions provider, or, if none, to
the TV’s own caption defaults.

Captions

Color
A white font on a black translucent background makes an easy-to-read combination.

For assistance call 1(800) 332-2119

4. TV Menus

Setup
Setup

Language
•
•

Setup

Select either English or Spanish for on-screen menus.
Select the language for a digital program from the ANT input (if available).

Clock
Set the TV clock to:
• Use the TV Timer to power on the TV automatically at a preset time
• Receive correct updates to ChannelView listings

Note: When the Daylight Savings Time change occurs, you must open this menu and set the TV’s clock ahead or back.

Setup

Timer
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day,
time, input, and channel for the Timer. If the TV is already on at the set time, the TV will automatically change to the designated channel or input.

•
•
•

The TV clock must be set before you can use the Timer feature.
As a reminder that the TV Timer is set, the TV POWER indicator flashes slowly while the TV is powered off.
When the Timer turns on the TV, press any key on the remote control to keep it from turning off after five minutes.

Setup

Channel
See “Memorizing Channels with Channel Scan” on page 7 to scan for all available channels
on the ANT input.

Edit
After channel scan, Edit lets you add and delete memorized channels.
• Press PAGE
/
to jump to the next or previous page of channel numbers.
• Press
to move through all channel numbers, one at a time.
Adding/Deleting Channels Using the Channel Edit Menu
• Channels marked with a check are in memory.
• To add or delete a channel from memory, highlight the channel number and press ENTER.
• To add a single digital channel not in the list, see the full owner’s guide at www.mitsubishi-tv.com.

Setup

Energy

Lamp
Energy

Standard, Standard is for most viewing conditions. Use Bright in brightly lit rooms. You may
Bright
notice increased fan noise when using the Bright setting.

Blue Glow
(838 series)

On, Off

Setup

Select On to see blue accent lighting when the TV is powered on.

Home
Network
Ethernet Connection
Wireless Connection

For assistance call 1(800) 332-2119

See “Home Network Setup,” page 19.

4. TV Menus

Inputs
Inputs

Name
•
•
•
•

•

Inputs

Lets you assign or change names of inputs appearing in the Input Selection menu.
Highlight the input and press ENTER to see the name choices.
Lets you turn the Ant input On/Off (to display or hide it in the Input Selection menu).
838 Series. Lets you turn the Bluetooth input On/Off (to display or hide it in the Input
Selection menu); a paired device is cleared from memory when the Bluetooth icon is
turned off.
Lets you delete unused HDMI inputs from the Input Selection menu.

Learn
838 Series. Sets up or changes NetCommand IR control of the current device.
See the full owner’s guide at www.mitsubishi-tv.com.

Inputs

AVR

Inputs

HDMI
Control

838 Series. Sets up or changes NetCommand IR control of an A/V receiver.
See the detailed owner’s guide at www.mitsubishi-tv.com.

On, Off

Inputs

Select On or Off to enable or disable the TV’s control of a CEC-enabled device.
See the detailed owner’s guide at www.mitsubishi-tv.com for use of this feature.

Order
Lets you rearrange icons in the Input Selection menu.

Inputs

Demo
See demonstrations showcasing selected TV features.

For assistance call 1(800) 332-2119

4. TV Menus

Lock
Parental Menu

•

The TV comes from the factory with the rating
locks turned off and with pre-set U.S. ratings
TV-PG and movie rating PG. You must turn
on blocking for U.S. ratings to activate these
rating restrictions. You will be prompted to
enter a pass code when you select Lock on
the main menu.

•
•

•

Important Notes on Rating Locks
Parental menu rating locks apply only to channels and signals received
on the ANT and composite VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT.
When viewing a cable box, satellite receiver, or other device connected
to the component Y Pb Pr or HDMI inputs, check the device’s owner’s
guide for parental locks.
When accessing VUDU’s internet movie service, use the parental controls provided by VUDU.

Lock

Parental

Lock

Disables or enables blocking based on V-Chip signals and the U.S. rating system.

TV
Rating

Highlight the rating level you wish to change
and press ENTER to block it ( ) or allow it ( ).
You can apply supplemental content blocking to the age-based ratings by using the TV
content categories. (FV, D, L, S, V)

Movie
Rating

Highlight the rating level you wish to change
and press ENTER to block it ( ) or allow it ( ).

Start Time/ Sets the time of day for enforcement of rating restrictions set in the Parental menu.
Stop Time Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.

Lock

Time
Blocks all use of the TV during the time period you specify. Once a lock time is set, it goes
into effect immediately and you must enter a pass code to use the TV during the lock period.
To reactivate the time lock, power the TV off and then back on. To make Lock by Time
active 24 hours a day, make Start Time and Stop Time the same.

Lock

Channel
The Channel Lock menu lists channels currently in memory (see page 24). Highlight a
channel and press ENTER to lock ( ) or allow ( ) the channel. Channels locks will be
cleared the next time you perform a channel scan.

Lock

Panel
Use this option if small children try to press TV buttons.
• To release the Panel Lock from the TV’s control panel, press and hold the INPUT button for
ten seconds. If the TV is powered off, press POWER after the lock releases to power on the
TV.
• To reactivate the lock, return to this menu and change the setting to On.

Lock

Other
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. Such alternate rating systems will apply only to digital programming received on the ANT input.

For assistance call 1(800) 332-2119

Appendices

Appendix A: TV Care
Lamp-Cartridge Replacement and Cleaning
CAUTION: If the television is on, press POWER to turn it off. Unplug the television and
allow it to cool for at least one hour before attempting to replace the lamp cartridge.
Lamp
The light source for this television is a
lamp, which is part of a lamp cartridge
assembly. The life of the lamp can
vary, based on the lamp itself, the air
temperature around the TV while it is
operating, the selected lamp mode, and
your viewing patterns. Warmer air or
poor ventilation shorten the lamp life, as
does setting Lamp Energy to Bright
and turning the television on and off
frequently.

CAUTION
BURN DANGER! HOT SURFACES INSIDE!
Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do
not tilt as glass may come out and cause injury. Replace lamp cartridge only with the same part number 915B441001.

Mitsubishi warrants the lamp for one (1) year from the date of original
TV purchase at retail.
To Order a New Lamp
To Receive a Replacement Lamp Under Warranty
• Visit our website at www.mitsuparts.com.
• Call (800) 553-7278. Please have model number, serial number,
and TV purchase date available.

WARNING
THE ACCESS PANEL IS
PROVIDED WITH AN INTERLOCK
TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT
ITS PURPOSE OR ATTEMPT TO
SERVICE WITHOUT REMOVING
PANEL COMPLETELY.

Important: All lamps replaced under warranty must be returned to
Mitsubishi where they will be inspected to verify failure defects.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call (800) 553-7278. Order the following:

Lamp Part Number 915B441001
Lamp-Substitution Alert
MDEA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a
Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MDEA advises that replacement lamps obtained
separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for
your television, may not fit or perform properly and may even damage your television. MDEA can not be responsible
for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.

WARNING
•
•
•
•
•
•

Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical
shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.
Install the lamp cartridge securely. Failure to do so may cause a fire.
Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.
Hg

= MERCURY

THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at www.eiae.org

For assistance call 1(800) 332-2119

Appendices

Appendix A: TV Care, continued
Lamp-Cartridge Replacement
Removing the Old Lamp Cartridge

1. Turn off TV power and unplug the TV. Allow the
2.

4.
5.

lamp to cool for at least one hour before proceeding.
After the lamp has cooled, remove the cover of the
lamp compartment, located on the back of the TV.
Refer to figures 1 and 2. Use a #2 (medium) Phillips
screwdriver to loosen the screw securing the cover.
Keep the screw and cover for re-installation
With a medium Phillips screwdriver, loosen the two
screws securing the lamp cartridge until they disengage from the mating threads. These are captive
screws and cannot be separated from the lamp
cartridge.
Fully open the bag supplied with the replacement
lamp and set the opened bag aside.
Gently grasp the handle of the lamp cartridge and
pull the old cartridge straight out. See figure 3.
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.

Installing the New Lamp Cartridge
1. Do not touch the glass parts of the new lamp cartridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
2. Gently tighten the screws with the screwdriver.
AVOID OVERTIGHTENING!
3. Replace the plastic cover and retaining screws.
4. WASH YOUR HANDS THOROUGHLY, AS THIS
LAMP CONTAINS MERCURY.

For assistance call 1(800) 332-2119

Figure 1

Figure 2

Figure 3

Use only replacement lamp part number
915B441001.
Disposal of the Old Lamp Cartridge
Lamp under warranty: All lamps replaced under warranty must be returned to Mitsubishi. Use the return
shipping label provided and send to Mitsubishi Digital
Electronics, America, 625 Braselton Parkway, Suite 200,
Braselton, GA 30517.
IMPORTANT: Lamps found without defects will be
returned and charged back to the sender.
Lamp no longer under warranty: Contact your
local authorities or the Electronic Industries Alliance at
www.eiae.org for lamp-disposal or recycling instructions.
Do not dispose of the old lamp with common trash.

Appendices

Appendix A: TV Care, continued
Cleaning Recommendations

Screen

Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from the
power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.

•
•
•

•

Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as some
liquid may enter the TV through the gap between the
screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling (800) 553-7278.

Top and Sides of the TV
•

•

Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with a
second dry, soft, non-abrasive cloth.
For oily dirt, add a few drops of mild liquid detergent,
such as dishwashing detergent, to the water used
to moisten the cloth. Rinse with a second cloth
moistened only with water. Dry with a third dry, soft,
non-abrasive cloth.

General Cleaning Precautions
•
•
•

•
•

DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.

For assistance call 1(800) 332-2119

Appendices

Appendix B: Programming the Remote Control
3. Enter the first five-digit code listed for your equip-

Programming the Remote Control
1. Change the control mode to match the device type.
TV
CAB/SAT

AUDIO
DVD

VCR

TV
CAB/SAT

AUDIO
DVD

VCR

5.
Mode

Affected Device

CAB/SAT

Cable Box, DTV Receiver, Satellite Receiver

VCR

VCR, DVR, DVD Player/Recorder

DVD

DVD Player/Recorder, DVR, VCR

AUDIO

A/V Receiver, Audio Amplifier, CD Player

ment.
Point the remote control at the equipment and press
POWER. If the product has no power on/off function,
press a different key, such as
(PLAY),
(STOP),
VOLUME UP, or MUTE.
If the equipment does not respond, repeat the preceding two steps using the next five-digit code.
Once you have found the correct code, write it in the
space below for future reference.
Mode

VCR
DVD

several seconds until the key blinks twice and goes off.

Cable Boxes
General Instrument
Jerrold
Motorola
Pace
Pioneer
Scientific Atlanta

10476
11376, 11187, 10476
11982, 11877, 11376
11877, 10877
11877, 10877

DVD Players

DirecTV

Funai
Hitachi
Insignia
Integra
JVC

A/V Receivers
Bose

41933, 41841, 41629, 41253,
41229, 40639
Denon
42857, 42279
Harman/Kardon 42443, 42241, 41306, 41304,
40891
Integra
41805, 41320, 41298
JVC
42331, 42239, 42040,
41495, 41374
Kenwood
41570, 41569, 41313
Mitsubishi
41957, 41922, 41921, 41920,
41393
Onkyo
41805, 41531, 41320, 41298,
40842
Panasonic
41763, 41633, 41548, 41518,
41316, 41308, 41288, 41275,
42967, 42452, 42221, 41764
Pioneer
41935, 41384, 41023, 40630
Sony
41759, 41758, 41658, 41622,
41558, 41441, 41258, 41058,
42522, 42216, 42172, 41858,
41822
Technics
41518, 41308
Yamaha
41476, 41376, 41375, 41331,
41276, 41176, 40376, 40176
42471, 42467, 42061, 41815

AUDIO

Satellite Receivers

Dish Network
System
Hughes Network
Systems
Mitsubishi
RCA
Samsung

11749, 11377, 11142, 10749,
10639, 10566, 10392, 10247
11856, 11609, 11442, 11414,
11109, 11076
10775, 11505, 11775
11749, 11442, 11142, 10749
10749
10566, 10392, 10143
11609, 11442, 11377, 11276,
11109

VCRs
Hitachi
JVC
Magnavox
Matsushita
MGA
Mitsubishi
Panasonic
RCA
Sony
Tivo
Toshiba
Zenith

20042, 20000
20067
21593, 20593, 20081, 20039,
20035, 20000
20162, 20035
20043
20173, 20067, 20043
21062, 20616, 20614, 20162,
20035
20880, 20060, 20042
21972, 21032, 20636, 20035,
20033, 20032, 20000
20739, 20636, 20618
21972, 21008, 20045, 20043
21139, 20039, 20037, 20033,
20000

DVD Players
Apex Digital

Coby
Denon

For assistance call 1(800) 332-2119

Code

CABLE/SAT

2. Press and hold POWER on the remote control for

This is an abbreviated list showing
the most popular codes. For a full
list, see the detailed owner’s guide at
www.mitsubishi-tv.com.

Device Type

31061, 31056, 31020, 31004,
30797, 30796, 30794, 30755,
30672
31628, 31351, 31177, 31165,
31107, 31086, 30852, 30778
32258, 30634, 30490

LG
Magnavox
Mitsubishi
Onkyo
Panasonic
Philips

Pioneer

RCA
Samsung

Sharp
Sony
Sylvania
Tivo
Yamaha
Zenith

30675
30664, 30573
32596, 32428, 32095, 30675
32147, 31769, 30627, 30571
32365, 31602, 31550, 31275,
31164, 30867, 30623, 30558
31602, 30869, 30741, 30591
31506, 31472, 31354, 31177,
30675, 30646, 30539, 30503
31521, 30521
32147, 31769, 30627, 30503
31762, 31641, 31579, 30703,
30632, 30503, 30490
32084, 32056, 31340,,
31267, 30675, 30646, 30539,
30503, 32434, 31506, 31354
31571, 31512, 31460, 30632,
30631, 30571, 30525, 30142
32442
32213, 31769, 30822, 30790,
30571, 30522
32069, 31470, 31075, 31044,
30820, 30573, 30490, 30199
32556, 32489, 32369, 32329
32250, 31256, 30752, 30675,
30630
31633, 31536, 31516, 31431,
31070, 31033, 30864, 30533
30675
31512, 31503
32558, 32298, 30817, 30646,
30545, 30539, 30490
30869, 30741, 30591, 30503

Appendices

Appendix C: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using the
reset functions described in the following table. .
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box,

or satellite receiver), first check other channels from
the same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.

Reset Name

When to Use

How to Use

Resulting Action

Format

If the picture shape
seems incorrect, use
the FORMAT key to
change the picture
shape.

Press FORMAT to cycle through the
picture shapes available for the
signal.

The last-used format for a signal
type will be recalled on the input.
Note: Also check the aspect
ratio feature on your cable box or
satellite receiver as this may be
altering the picture.

PerfectColor™/
PerfecTint™
Reset (838
Series)
(for the single
input currently
being watched)

1. While viewing the input to be
When the color
reset, press MENU and go to
intensities seem out
of balance, use the
Picture > Perfect.
PerfectColor/PerfecTint 2. Press ENTER to display the
reset to reset the color
PerfectColor adjustment screen.
balances to the original
3. Press CANCEL to reset the colors.
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.

All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.

A/V Memory
Reset
(for the single
current input)

When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.

All Audio and Video settings for
the individual input are reset
except for the global settings
for audio Balance, Listen To,
Language, Video Mute, Smooth
120.

1. While viewing the input to reset,
press MENU and go to Picture >
Reset.
2. Press ENTER to highlight Reset.
3. Press ENTER again to reset.

Service and Customer Support
Service
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Consumer Relations at (800) 332-2119.
•

DO NOT adjust any controls other than those
described in this Owner’s Guide.

•

DO NOT remove the protective back cover of
your TV.

Customer Support
•

To order replacement or additional remote controls or lamp cartridges, visit our website at www.
mitsuparts.com or call (800) 553-7278.

•

For questions:
Call Consumer Relations at 800-332-2119.
E-mail: MDEAservice@mdea.com
Website: www.mitsubishi-tv.com

Important
All lamps replaced under warranty must be returned
to Mitsubishi where they will be inspected to verify
failure defects.

For assistance call 1(800) 332-2119

Appendices

Appendix C: Troubleshooting, continued
Reset Name

When to Use

How to Use

Resulting Action

A/V Reset
(for all inputs)

To reset audio and
video adjustments for
all inputs to the original
factory settings.

While viewing the TV, press the
control-panel buttons INPUT and
VOLUME DOWN at the same time for at
least two seconds.

All Audio and Video settings are
returned to the original factory
settings, including global settings
not affected by Picture > Reset.

Channel
Memorization

To erase and
re-memorize channels
on the ANT input.

1. Press MENU and go to Setup >
Channel.
2. Highlight the reception mode,
e.g. Ant Air, and press ENTER.
3. Highlight All Channels and
press ENTER.
4. Highlight Scan.
5. Press ENTER to start channel
memorization.

All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. To
add or delete individual channels,
see the Setup > Channel > Edit
menu instructions on page 24.

Lock Menu
Pass Code

To change your Lock
menu pass code

See the detailed owner’s guide at www.mitsubishi-tv.com for instructions.

Control-Panel
Lock Release

To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock

Press and hold the INPUT button on
the control panel for ten seconds. If
the TV is powered off, you can now
press the POWER button to turn it on.

Allows the control panel to be
unlocked if the remote control is
misplaced.

System Reset

If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.

Press and hold the POWER button on
the control panel for ten seconds.

The TV will turn off. Power on the
TV and the green LED will flash
quickly for about one minute. The
changes you made most recently,
before using SYSTEM RESET, may
be lost.

TV Reset

To reset all consumeraccessible settings
and all memories to
the original factory
defaults.

1. While viewing the TV, press
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
Use TV Reset if the TV
3. READ THE ON-SCREEN
can respond to conWARNING AND INSTRUCtrols but TV behavior is
TIONS.
abnormal.
• If you do not wish to use this
CAUTION: All ownerreset, press EXIT or MENU to
performed setups and
back out.
adjustments will be
• If you wish to continue,
erased.
press ENTER to erase all
memories and settings.

The TV will start the initialization
process and then turn off.
Power on the TV and the front
green LED will start flashing. All
memory and settings outlined in
this Owner’s Guide will need to
be set again.

VUDU
Reset VUDU
Account Password

You have forgotten
your account password.

Using a computer, go to
www.VUDU.com.

Reset your account password
from the VUDU website (requires
access to e-mail).

VUDU
Reset Parental
Controls Pass
code

You have forgotten
your pass code.

Call VUDU Customer Care at
1-888-554-VUDU (8838).

VUDU Customer Care will reset
your pass code.

IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuccessful.

For assistance call 1(800) 332-2119

Appendices

Appendix C: Troubleshooting, continued
Common Picture Problems
1.

Symptom

Remarks

Picture does not look like a high-definition picture.

Compare the picture to the TV’s test picture (Picture > Picture+ >
Test Picture) to check if the source signal is supplying a lesser-quality
image.
Not all signals are high-definition signals. To receive high-definition
programming from your cable or satellite provider, you must subscribe
to the provider’s high-definition service. Some over-the-air broadcasts
are in high-definition and can be received with a high-quality antenna
suited to your location.

TV has sound but no picture.

•
•
•

Press MENU on the remote control. If the menu displays, then there
is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the correct input
jacks.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.

Picture has become dimmer.

•
•
•

The lamp is nearing the end of its life. Order a new lamp.
Adjust picture brightness and contrast to maximum levels.
Change Lamp Energy from Standard to Bright.

A color program appears as a black
and white image, or the colors are
dim, or the screen is black.

•

If using component video, check that the red, green, and blue input
cables are correctly connected to the red, green, and blue component video jacks.
If using composite video, check that the incoming cable is connected the TV’s green Y/VIDEO jack.
838 Series. The PerfectColor color balance has been incorrectly
set. Reset the PerfectColor balance.

•
•
5.

Picture from an HDMI input is noisy
(poor quality).

•
•

Compare the picture to the TV’s test picture (Picture > Picture+ >
Test Picture) to check if the noise is internal or external to the TV.
Upgrade a Category 1 (unmarked) HDMI cable to a newer type of
high-speed HDMI cable.

Home Network
Symptom

Remarks

I cannot connect the TV to the
network.

Go to the Setup > Network menu. Obtain the TV MAC address and
provide it to the router.

I plugged in a wireless USB adapter,
but the wireless connection is not
working.

The network may be locked. Go to Setup > Network. Highlight the
network name and supply the pass code.

The INTERNET key only goes to
VUDU.

Normal operation. The TV receives all internet services through VUDU.
The TV does not provide full internet access as does a web browser on
a computer.

For assistance call 1(800) 332-2119

Trademark and License Information

Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By
utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any
violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license
is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software
is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.

For assistance call 1(800) 332-2119

Trademark and License Information

Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and
change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”,
below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable
copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and
will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties
remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its
terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those
who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published
by the Free Software Foundation.

If you are interested in obtaining open source code for this product, please contact Mitsubishi at
(800) 332-2119. A nominal handling and mailing charge may apply.

For assistance call 1(800) 332-2119

Trademark and License Information

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our
free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS
WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007

Copyright © 2007 Free Software Foundation, Inc.
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share
and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work
released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish),
that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it:
responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that
their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to
prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special
danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or
a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a
private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is
no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or
options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among
developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b)
serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a
major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those
activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For
example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as
provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them
make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus
making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship
with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting
or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered
work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices
stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the
Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b)The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the
work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d)If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit.
Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
b)Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer
support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code
with such an offer, in accord with subsection 6b.
d)Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need
not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.

For assistance call 1(800) 332-2119

Trademark and License Information

e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection
6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a
dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common
use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified
version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is
transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But
this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User
Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and
must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though
they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases
when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b)Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or
d)Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual
assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License
along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material
governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b)
permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this
License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do
not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy
likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by
modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance
by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity
transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this
License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right
to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents
of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available
network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3)
arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work
authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this
License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of
your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work
conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license
was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work
so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty
for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and
to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction
through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms
and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any
version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil
liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.

For assistance call 1(800) 332-2119

Warranty

Mitsubishi Home-Cinema Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a
period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase
at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded
Software”) will perform in accordance with the functional description of Embedded Software in all material respects,
but MDEA does not warrant that the Embedded Software is error-free. The limited warranty contained in this section
shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within
the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such
functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at
no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software
contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation
to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to
your acceptance of and compliance with the terms of the Software License Agreement applicable to this television,
and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or
changed in any manner except as specifically authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but
not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other
parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for
one (1) year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the
image using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants
only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and
correct customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be
provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However,
please return the Owner Registration Card so that we can contact you should a question of safety arise which could
affect you.

For assistance call 1(800) 332-2119

Warranty

d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged
by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered,
defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage
caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage
caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the
product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal
unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other
damages arising from product installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection
with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced
outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the
product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the
state where the television was purchased and the laws of such state will govern.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904

Network Service Disclaimer
Third party content and services, including without limitation home entertainment services by VUDU, Inc., are provided in accordance with whatever terms and conditions are established by the third party providers and agreed to by you. Mitsubishi Digital Electronics America (“MDEA”) has
no control over any such third parties or any agreement you reach with them. MDEA has no control over the networks or transmission facilities
by which content and services are provided by third parties. Your connection to the internet may vary in availability and quality. Customer service
questions are to be directed to the third-party provider, not MDEA.
MDEA DOES NOT WARRANT CONTENT OR SERVICES PROVIDED BY ANY THIRD PARTY, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY
PURPOSE. MDEA DOES NOT WARRANT THAT ANY THIRD PARTY SERVICE WILL REMAIN AVAILABLE FOR ANY PERIOD OF TIME OR THAT IT
WILL BE SATISFACTORY, UNINTERRUPTED OR ERROR FREE. MDEA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY THIRD PARTY
CONTENT AND SERVICES.
MDEA WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE, WHETHER IN CONTRACT OR TORT OR OTHER LEGAL THEORY, FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES
ARISING OUT OF, OR IN CONNECTION WITH, YOUR USE OF ANY CONTENT OR SERVICE THAT IS PROVIDED TO YOU BY ANY THIRD PARTY,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

For assistance call 1(800) 332-2119

Website:

E-mail:

www.mitsubishi-tv.com

MDEAservice@mdea.com

Call Consumer Relations for operational or connection assistance at
800-332-2119
To order replacement or additional
remote controls, lamp cartridges, or NetCommand IR emitters,
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control, control-panel
buttons, or will not power on/off, press and hold the POWER
button on the control panel for ten seconds.
The TV will turn off. Power on the TV and the green LED will flash
quickly for about one minute. Recent settings changes may be lost.

Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
Digital Light Processing® and DLP® are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
ENERGY STAR® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
VUDU™ is a trademark of VUDU, Inc.
ChannelView™, DeepField™ Imager, Easy Connect™, EdgeEnhance™, NetCommand®, PerfectColor™, PerfecTint™,
Plush 1080p® 5G, Smooth120Hz™, StreamTV™ are trademarks of Mitsubishi Digital Electronics America, Inc.
V43+/V43++
© 2010 Mitsubishi Digital Electronics America, Inc.

853B710B50

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : V43+_V43++_BIB_853B710B50_20100707.indd
Creator                         : dmh9789
Create Date                     : 2010:07:30 14:21:54-07:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2010:07:30 14:21:54-07:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:772eeb5e-dcef-4609-b53b-58ee4ef38390
Instance ID                     : uuid:d4542b41-112b-4853-a9b0-75e44a7bf4e0
Page Count                      : 40
Author                          : dmh9789

EXIF Metadata provided by EXIF.tools

V43+_V43++_BIB_853B710B50_20100707 Mitsubishi Digital Electronics Home Theater System 838 738 BIB V3

Navigation menu

Versions of this User Manual:

Views

Navigation