1036_82058M 82058M
User Manual: 82058M
Open the PDF directly: View PDF .
Page Count: 2

25 mm In-line Filter Holder, Delrin*
• Lightweight filter holder for particulate sampling.
• Useful for low pressure, in-line air cleaning, liquid filtering or sampling
applications.
• Easily incorporated into liquid- or gas-carrying tube systems at the point of use.
• Domed inlet provides uniform sample distribution on the membrane.
Ordering Information
Prod. No. Description Packaging
1109 25 mm In-line filter holder 6/pkg
Specifications
Materials of Construction
Body: Delrin (acetal resin)
Support Screen: Type 316 stainless steel, heat-sealed in place
Hose Barb Adapters: Nylon
O-ring: Viton*
Effective Filtration Area
3.7 cm2
Dimensions
Overall Length: 2 cm (0.8 in.)
Diameter: 3.5 cm (1.4 in.)
Inlet/Outlet Connections
1/8 in. FNPT; hose barb adapters accept 6.4 mm (1/4 in.) ID tubing
Maximum Operating Temperature
In Water: 66 °C (151 °F)
In Air: 85 °C (185 °F)
Maximum Operating Pressure
2.8 bar (280 kPa, 40 psi)
Sterilization
Provided non-sterile; autoclavable if desired 121 - 123 °C (250 - 253 °F) at
approximately 1.0 bar (100 kPa, 15 psi) for a maximum of 15 minutes.
Instructions for Use
1. Place a 25 mm membrane filter on top of the support screen. Be sure separator
discs are not placed inside the holder.
2. Place the O-ring on top of the membrane filter.
3. To ensure a proper seal, hold level while connecting the inlet.
4. Hand tighten the hose barb adapters on the inlet and the outlet connections.
5. Use of membrane filter and glass prefilter is recommended separately. Do not
use a pre- and final filter together as a unit. The combined thickness may cause
leakage.
6. Make certain the inlet and the outlet are oriented in the intended direction of flow.
Cleaning/Autoclaving Instructions
1. To clean the filter holder, disassemble the unit and clean with a non-abrasive
cleanser.
2. Rinse thoroughly with deionized water.
3. Allow to air dry.
4. If autoclaving is required, reassemble the unit loosely with or without the
membrane filter in place.
5. Wrap the assembled filter holder in autoclave paper.
6. Autoclave at a maximum of 121 - 123 °C (250 - 253 °F) at approximately
1.0 bar (100 kPa, 15 psi) for 15 - 20 minutes. The maximum autoclave
temperature may be limited by the membrane type. Please refer to the
membrane specifications for complete information.
7. Avoid using steam containing amines. It may cause the membrane filter to
become brittle and/or contaminate the product or solution being filtered.
Cap
Base
Support Screen
O-Ring
Hose Barb Adapter
Hose Barb Adapter
1036_82058M 8/17/05 1:54 PM Page 1

Replacement Parts
Prod. No. Description Packaging
73179 Hose barb adapter, nylon 1/8 in. MNPT to 1/pkg
6.4 mm (1/4 in.) ID tubing
83475 O-ring, Viton*, ARP No. -117 1/pkg
WARNING
Employment of the products in applications not specified, or failure to follow
all instructions contained in this product information insert, may result in
improper functioning of the product, personal injury, or damage to property
or the product. See Statement of Warranty in our most recent catalog.
ATTENTION
L’utilisation de nos produits dans des applications pour lesquelles ils ne
sont pas spécifiés ou le non-respect du mode d’emploi qui figure sur ce
document, peut entrainer un disfonctionnement du produit, endommager le
produit ou d’autres biens matériels ou représenter un risque pour l’utilisateur.
Se référer à la clause de garantie de notre catalogue le plus récent.
ACHTUNG
Der Einsatz dieses Produktes in Anwendungen für die es nicht spezifiziert
ist, oder das Nichtbeachten einiger, in dieser Bedienungsanleitung
gegebenen Hinweise kann zu einem schlechteren Ergebnis, oder Zerstörung
des Produktes oder anderer Dinge oder gar zu Verletzungen führen.
Beachten Sie auch unsere Garantiebedingungen im aktuellen Katalog.
ADVERTENCIA
El uso de este producto en aplicaciones no especificadas o el no considerar
las instrucciones indicadas en la hoja de información del producto puede
ocasionar un mal funcionamiento del producto, daños en las instalaciones o
en el producto y riesgo para el personal del laboratorio. Consulte el
apartado de Garantía en nuestro último catálogo.
ATTENZIONE
L’impiego dei prodotti in applicazioni non specificate, o il mancato rispetto
di tutte le istruzioni contenute nel presente bollettino tecnico, potrebbero
portare ad un utilizzo improprio del prodotto, ferire gli operatori, o
danneggiare le caratteristiche del prodotto stesso. Consultare la
dichiarazione di garanzia pubblicata nel nostro più recente catalogo.
Pall and are trademarks of Pall Corporation. *Delrin is a trademark of E. I. DuPont De Nemours, L.L.C. Viton is a
trademark of DuPont Dow Elastomers, L.L.C. ® indicates a registered trademark in the USA.
© 2005, Pall Corporation, 08/05 PN 82058M
Pall Life Sciences
600 South Wagner Road
Ann Arbor, MI 48103-9019 USA
For ordering or technical information:
Tel: 734-665-0651
800-521-1520 (in USA)
Fax: 734-913-6114
Visit Pall Life Sciences on the
Internet: www.pall.com/Lab or
e-mail us at: Lab@pall.com
Offices:
Australia, Lane Cove, NSW, 02 9424-3000
Austria, Wien, 00 1 49 192 0
Canada, Ontario, 905-542-0330
Canada, Québec, 514-332-7255
China, P.R., Beijing, 86-10-8458 4010
France, St. Germain-en-Laye, 01 30 61 39 92
Germany, Dreieich, 06103-307 333
India, Mumbai, 91 (0) 22 55995555
Italy, Milano, 02 47 79 61
Japan, Tokyo, 03-6901-5800
Korea, Seoul, 82-2-560-7834
Malaysia, Selangor, +60 3 5569 4892
New Zealand, Hamilton, +64 7 957 9510
Poland, Warszawa, 22 510 2100
Russia, Moscow, 5 01 787 76 14
Singapore, (65) 389-6500
South Africa, Johannesburg, +27-11-2662300
Spain, Madrid, 91-657-9876
Sweden, Lund, (0)46 158400
Switzerland, Basel, 061-638 39 00
Taiwan, Taipei, 886 2 2545 5991
Thailand, Bangkok, 66 2937 1055
United Kingdom, Farlington, 02392 302600
1036_82058M 8/17/05 1:54 PM Page 2