59545/59655 82207728

User Manual: 82207728

Open the PDF directly: View PDF PDF.
Page Count: 8

Download59545/59655 82207728
Open PDF In BrowserView PDF
GENUINE ACCESSORIES

GB

INSTALLATION INSTRUCTION
Parts must not be fitted until registration of the vehicle has been obtained.

E

INSTRUCCIONES DE MONTAJE

F

NOTICE DE MONTAGE

Top Kit

No se permite montar las piezas antes de registrar el vehiculo.

Ne pas monter les pièces avant l’enregistrement du véhicule.

JP

Subject to alteration without notice
Reservadas modificaciones lecnicas
Sous réserve de modifications techniques

1997
1997
1997
1997
2001
2001
2003
2003

82202125
82202126
82202127
82204553
82206623
82206624
82207728
82207729

59545
59545
59545
59545
59645
59645
59655
59655

© DAIMLERCHRYSLER
59545 / 59645 / 59655

Rev. 3 1002

1 of 8

K6858707

GENUINE ACCESSORIES
Fabric Top

Quarter Window Driver’s

A

AA

Rear Bow Assy. Driver’s Side Section

Rear Bow Assy. Passenger’s Side Section

B

C

Pivot Bracket - Passenger’s

F

G

Door Surround - Passenger’s

J
Side Bow - Driver’s

Tailgate Mount - Driver’s

Door Surround Knob

K
Side Bow - Passenger’s

Quarter Window Passenger’s

Rear Window

BB

CC

Rear Bow Assy.

Pivot Bracket - Driver’s

D
Tailgate Mount - Passenger’s

H

E
Door Surround - Driver’s

I

Header Assembly

Center Bow

L

M

Tailgate Bar

#8 x 1/2" Pan Head Washer
Screw

X12

N
59545 / 59645 / 59655

O
Rev. 3 1002

P
2 of 8

Q
K6858707

GENUINE ACCESSORIES
#8 x 1/2" Self Drilling
Screw
X2

R

Pan Head Screw

S
M5 x 30 Machine Screw

X4

V

W

U

Bushing

M5 Hex Nut

X4

DD

Phillips
Screwdriver

X4

X

.5ml Tube Red Loctite

Drill

X2

Y

Rear Window Roll-Up
Straps (2 per package)

EE
Adjustable
Wrench

Sizes 1, 2 and 3

X4

T
X2

#12 x 3/8" Tapping Screw

1

Pivot Bracket Bolt

X2

X14

Pivot Knuckle Bolt

Z

Oval Screw

T-30 Torx

2

3

Silicone
Sealant

1/8"

4
59545 / 59645 / 59655

5
Rev. 3 1002

3 of 8

K6858707

GENUINE ACCESSORIES
B

X2

DD

L

D

ORIENT LEGS
HOLES OUT

Z

R

ORIENT LEGS

1
Orient the legs with the holes in the pivot knuckles
toward the outside. Slide the pieces together, aligning the pre-drilled screw holes. Install a #8 x 1/2
Self Drilling Screw, from the parts kit, in each leg.

N
Orient the Side Bows with the holes in the pivot
knuckles toward the outside. Slide the other
end over the section of tube and into the header. Install the #12 x 3/8" Tapping Screws, one
on each side of the bow, on each side of the
header (4 screws). Place a drop of Loctite on
the threads of each screw before installing.

C

Y

WITH

HOLES OUT

X2

1

Z

X4

WITH

1

2

M

M

X2

X
1
OUTSIDE

W

N

N

2

DRIVER’S SIDE
Locate the Center Bow Assembly with the fabric Stay Pads attached. Lay the bumpers of the Center Bow on top
of the Side Bows and align the holes in the Center Bow with the holes in the Side Bows. Push an M5 x 30 Pan
Head Screw through the Side Bow from the outside, install a bushing with the shoulder facing away from the Side
Bow, slide the rod of the Center Bow over the screw, install a second bushing with the shoulder facing into the
hole in the Center Bow. Install the nut. Tighten the assembly so that the Center Bow is allowed to rotate freely.

3

SPORT BAR

X2

X2
V

E

U

E
Front

Front

3

3
DRIVER’S SIDE

4

N

DRIVER’S SIDE

Unzip the vertical padded cover over the sport bar
and pull the pad away from the bar to expose the
bracket location holes. Orient the Pivot Brackets over
the existing holes in the sport bar and install them
with the Pivot Bracket Bolts (two bolts per bracket).

59545 / 59645 / 59655

Rev. 3 1002

5

4 of 8

Install the Side Bow Pivot Knuckles onto the upper
flange of the Pivot Bracket. Align the knuckle with the
bracket and snap it into place. Install a Pivot Knuckle
Bolt.
K6858707

GENUINE ACCESSORIES
X2
X2

M

N

Q
Q

E

2002 and
Earlier
Models

V
Front

B

3

SPORT
BAR

1
DRIVER’S SIDE
Install the Rear Bow Pivot Knuckle Assemblies onto
the lower flange of the Pivot Bracket with the holes
in the Pivot Knuckles facing the outside of the vehicle. Align the knuckle with the bracket and snap it
into place. Install a Pivot Knuckle Bolt.

6

D

X2

7

I

INSERT PIN

Rotate the front bow assembly forward, laying the
header on top of the windshield. Raise the Rear Bow
and pull the fabric Stay Pad attached to the Center
Bow straight back to the Rear Bow, without twisting.
Align the holes in the Stay Pad with the holes in the
corner of the Rear Bow. Install #8 x 1/2" Pan Head
Washer Screws in the holes on each side.

K

X2

I

K

INTO

HOLE IN BELT RAIL

CHANNELS

VIEW

FROM INSIDE

ABOVE

DRIVER'S SIDE

DRIVER'S SIDE

8

Locate the left and right Door Surrounds. Insert
the pin in the bottom of the Door Surround into
the hole in the belt rail behind the door.

X2

Press the channels along the top of the Door
Surround around the horizontal sport bar, above
the door opening. Insert two knobs into the Door
Surround and tighten them down.

9
G

G

X4
DRIVER'S SIDE

DRIVER'S SIDE

5

PLACE HOLES IN
TAILGATE MOUNT

5

OVER DIMPLES IN
BODY

10

Locate the left and right Tailgate Retainer
Mounts. Place the holes in the mounts
over the dimples in the vehicle body.

59545 / 59645 / 59655

Rev. 3 1002

X4

11
5 of 8

Drill a 1/8" hole at the marked
locations. Deburr the holes and
seal the edges of the holes with
Silicone Sealant.

1/8"

4
K6858707

GENUINE ACCESSORIES
G

X2

Q

Q
DRIVER'S SIDE

12

Install the Tailgate Retainer Mounts
with two #8 x 1/2" Pan Head Washer
Screws for each mount.

S

Fold the bows and the header down on
the rear of the vehicle.

13

1
A

X14

A

1st

L

3rd
2nd
1

14

Lay the Top, backing side up in the rear of the vehicle with the plastic strip facing up and aligned with the
front edge of the header. Locate the round hole that marks the center of the plastic strip (all other holes are
slotted). Install a Pan Head Screw in the round hole to secure the fabric to the header as well as to center
the top. Then proceed to install screws in the rest of the fourteen holes along the front of the header.

X2

T

X2

A

L

D

A

EE
A
REAR OPENING

1

15

Flip the fabric over so that it wraps around the
header and drape the top fabric over the tailgate.
Raise the header slightly and work the pockets
in the fabric over the corners of the header.
Install an Oval Head Screw in each corner to
secure the fabric to the header.

59545 / 59645 / 59655

Rev. 3 1002

Raise the header and bow assembly toward the
windshield and into position.

16

6 of 8

Inside the top, snap the fabric to the Rear Bow
(four snaps). Snap the Rear Window Roll-Up
Straps to the outer snap on the bow on each side.
K6858707

GENUINE ACCESSORIES
X2

X2
A

A

VIEW

17

FROM INSIDE

VEHICLE

Close the header latches to secure the front of the
top to the windshield. Catch the hook in the slot in
the windshield frame and then close the lever over
it so that it lays flat against the windshield frame.

18

Make sure that the Center Bow is centered in the
hook and loop flap inside the top. Do not fasten the
flap at this time.Pull down on the Rear Bow and
work the plastic sewn to the rear corners of the top
into the retainer on the vehicle.

A
A

A

X2
AA

M
SPORT BAR

VIEW

19

AA

FROM INSIDE

VEHICLE

Wrap the hook and loop flap inside the top
around the Center Bow and fasten it to itself.

20

X2

A

X2

Locate the left and right Quarter Panels and orient
them with the zipper along the top and rear of the
panel. Start the zipper at the front top corner of the
Quarter Panel, next to the door. Hold the end of
the zipper and close the zipper slider 10" - 12"
along the top of the panel.

AA

A
I

21

Roll the plastic along the front of the Quarter
Panel into the channel of the Door Surround on
the vehicle.

59545 / 59645 / 59655

Rev. 3 1002

22
7 of 8

Roll the two plastic strips above each door opening into the channel in the Door Surround on each
side of the vehicle.
K6858707

GENUINE ACCESSORIES
A

X2

CC

AA

23

P

Close the zippers on the Quarter Panels the rest of
the way. Start at the rear and roll the plastic on
the bottom of the panel into the retainer on the
vehicle. Fasten the hook and loop strips along the
top and rear of the panel to the Top.

24

Slide the "C" channel on the Tailgate Retainer onto
the tubed strip sewn to the Rear Window.

A

A

CC

CC

G

CC

P
A

25

To start the zipper, pull the two sliders as far down as
possible on the driver's side of the window in order to
catch the sliders to the pin. Once the zipper is
caught, start the top slider 1/2". Then hold up the top
of the window with one hand and close the zipper
with the other. The zipper is sandwiched between layers of fabric in the corners so be careful not to catch
extra fabric in the zipper. Close the zipper.

Insert the Tailgate Bar into the Tailgate Mounts on
each side of the tailgate opening.

A
AA

CC

26

Make sure that the Tailgate Bar is centered and is
securely in the mounts. Then tuck the flaps on the
Rear Window under the top fabric.

SPORT BAR
VIEW

27

FROM INSIDE

VEHICLE

Inside the top locate the flaps sewn to the top on
each side of the rear window opening. Pull the
flaps over to cover the zipper and tuck them in.

59545 / 59645 / 59655

Rev. 3 1002

8 of 8

K6858707
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2002:10:15 12:53:22
Producer                        : Acrobat Distiller 4.0 for Macintosh
Author                          : Jennie
Creator                         : QuarkXPressª: AdobePS 8.5.1
Title                           : 59545/59655.qxd
Modify Date                     : 2002:10:15 12:53:23-07:00
Page Count                      : 8
EXIF Metadata provided by EXIF.tools

Navigation menu