931 Wiring Diagram
User Manual: 931 wiring diagram
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
POWER SUPPLY FOR ELECTRIC DOOR-OPENER SYSTEM WITH BUILT-IN TWO-TONE ELECTRONIC SOUNDER AND FOR NOTICE OF CALL IN DOOR ENTRY PANEL WIRING INSTRUCTIONS Art. 931A/C17 CONNECTIONS TO TERMINALS OF POWER SUPPLY: PRI: } 1: 2: 3: 3 (-): 6 (+): 6: 7: 8: CSA product is according to UL 6500 Description of symbols shown in the power supply. double square: it is a class II power supply triangle with ligthning: hazard of electric shock, dangerous voltage; Triangle with exclamation mark: danger, pay attention. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN C1: CP: 0: 15: 0: N.B. When using continuous duty 0-15 and 0-AS outputs, do not connect loads of over 0.25A. AS: Handset receiver Handset microphone Handset receiver and microphone common Intecommunication system power supply 9V c.c. Common receiver and microphone for speech unit Speech unit microphone Speech unit loudspeaker Output for call generator with modulated sound for push-buttons commun wire, to be used with “Sound System” series interphones. Output for call generator with continuous sound for push-buttons commun wire, to be used with “Sound System” series interphones. 15V~ output for commun wire push-buttons to be used with A.C. call interphones. C2: The circuits inside the power supply are further protected by a SIEMENS PTC, type C965. Cod. S6I.931.A17 } } } Supply 117V∼ +10% -10% 60Hz 30VA protect by PTC SIEMENS C840. Power dissipated by power supply: 8,5 W } } RL. 01 Output 15V∼ 1A (on intermittent operation) 3 sec. ON, 180 sec. OFF, 0,4A continuous protect by PTC SIEMENS C945 3 sec. ON, 180 sec. OFF, 0,4A continuo Output 15V rectified 1A (on intermittent operation) 3 sec. ON, 180 sec. OFF, 0,4A continuous protect by PTC SIEMENS C945 3/2011 IMPORTANT SAFETY INSTRUCTIONS 1- Read these instructions 2- Keep these instructions 3- Heed all warnings 4- Follow all instructions 5- Do not use this apparatus near water 6- Clean only with dry cloth 7- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat. 9- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11- Only use attachments/accessories specified by the manufacturer. 12- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, not be placed on this apparatus CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 13- Apparatus shall not be exposed to dripping or splashing and no objects with liquids, such a vases, shall be placed on the apparatus. 14- The set disconnection device from the mains is the plug. TECHNICAL CHARACTERISTICS OF POWER SUPPLY ART. 931A/C17 Power supply in grey ABS housing; preset for mounting on cases with DIN 8-module support. This power supply features a dual electronic tone generator which replaces the traditional alternating current call on a buzzer or bell. The sound signal has two different tones (on terminals C1-C2), enabling users to immediately identify which point is calling (main entrance, gate, garage, etc.). This solution also makes it possible to use a single loudspeaker built into the phone itself to produce the sound. The use of C1 terminal for push-buttons commun wire for calls coming from the panel enables the activation of an acoustic signal in the same panel when calls are made to the interphones. Furthermore, this power supplier has been preset for operation with interphones with A.C. call; for such purpose terminal “CP” must be used as push-buttons “commun” terminal for calls from the door entry panel, which also routes an acoustic sound to the panel. OPERATING INSTRUCTIONS This power supply can be used for two types of systems: 1) Simple communication between the inside phones and outdoor unit (Art. 930). Diagram c3693, c3694. 2) Communication between the speech unit (Art. 930) and inside phones with conversation privacy between users. In this case only the phone called from the outdoor unit is enabled for conversation and release of the lock, if any, on the door. Diagram c3762, c3763. SAFETY INSTRUCTIONS FOR INSTALLERS - Carefully read the instructions on this leaflet: they give important information on the safety, use and maintenance of the installation. - After removing the packing, check the integrity of the set. Packing components (plastic bags, expanded polystyrene etc.) are dangerous for children. Installation must be carried out according to national safety regulations. - It is convenient to fit close to the supply voltage source a proper bipolar type switch with 3 mm separation (minimum) between contacts. - Before connecting the set, ensure that the data on the label correspond to those of the mains. - Use this set only for the purposes designed, i.e.for electric door-opener systems. Any other use may be dangerous. The manufacturer is not responsible for damage caused by improper, erroneous or irrational use. - Before cleaning or maintenance, disconnect the set. - In case of failure or faulty operation, disconnect the set and do not open it. - For repairs apply only to the technical assistance centre authorized by the manufacturer. - Safety may be compromised if these instructions are disregarded. - Do not obstruct opening of ventilation or heat exit slots and do not expose the set to dripping or sprinkling of water. - Installers must ensure that manuals with the above instructions are left on connected units after installation, for users' information. - All items must only be used for the purposes designed. - The ominipolar switch must be easily accessed. - WARNING: to avoid the possibility of hurting yourself, this unit must be fixed to the wall according to the installation instructions. - This leaflet must always be enclosed with the equipment. Directive 2002/96/EC (WEEE) The crossed-out wheelie bin symbol marked on the product indicates that at the end of its useful life, the product must be handled separately from household refuse and must therefore be assigned to a differentiated collection centre for electrical and electronic equipment or returned to the dealer upon purchase of a new, equivalent item of equipment. The user is responsible for assigning the equipment, at the end of its life, to the appropriate collection facilities. Suitable differentiated collection, for the purpose of subsequent recycling of decommissioned equipment and environmentally compatible treatment and disposal, helps prevent potential negative effects on health and the environment and promotes the recycling of the materials of which the product is made. For further details regarding the collection systems available, contact your local waste disposal service or the shop from which the equipment was purchased. Risks connected to substances considered as dangerous (WEEE). According to the WEEE Directive, substances since long usually used on electric and electronic appliances are considered dangerous for people and the environment. The adequate differentiated collection for the subsequent dispatch of the appliance for the recycling, treatment and dismantling (compatible with the environment) help to avoid possible negative effects on the environment and health and promote the recycling of material with which the product is compound. 2 A- Entrance panel series Patavium 8000, 8100, 1200, 3300 B- Additional push-button for lock C- Electric lock 12V∼ D- Outdoor unit Art.930, 930A L1- Bulb for panel lighting (3x24V 3W max.) 10x24V 3W with Art. 832/C17 16X24V 3W with Art. 832/3C7 POWER SUPPLY Art. 931A/C17 PRI 1 2 3- C2 6 7 8 C1 CP O 15 AS MAINS A L1 PHONE Art. 8875 Art. 8872 B 1 2 3 4/5 6 7 8 3 4 5 6 7 8 D ELVOX C PHONE Art. 6200 C A 7 AU 1 2 3 5 6E 6 6P 6S N.B. IN CASE OF NOISE IN THE AUDIO MOVE, IN THE POWER SUPPLY, THE WIRE CONNECTED ON THE DOOR LOCK TERMINAL N. 15 TO TERMINAL AS. 1 2 3 S CH N° C3693 WIRING DIAGRAM OF ELECTRIC DOOR OPENER WITH "SOUND SYSTEM" CALL, CONVERSATION PRIVACY, DIRECT LOCK RELEASE NOTICE AND CALL IN DOOR ENTRY PANEL 3 PHONE Art. 8878 POWER SUPPLY Art. 931A/C17 MAINS PRI 1 2 3- C2 6 7 8 C1 CP O 15 AS 1 2 3 6 6E 7 8 PHONE Art. 6200 + Art. 6155 C A 7 AU 1 2 3 5 6E 6 6P 6S E AU 1 2 3 6E A L1 3 4 5 6 7 8 1 2 3 S CH D R C B AC C AS BL BI RO A+ A- A- Entrance panel series Patavium 8000, 8100, 1200, 3300 B- Additional push-button for lock C- Electric lock 12V∼ D- Outdoor unit Art.930, 930A E- Card for conversation privacy Art. 6155 L1- Bulb for panel lighting (3x24V 3W max.) 10x24V 3W with Art. 832/C17 16X24V 3W with Art. 832/3C7 N.B. On interphone Art. 8878 leave the jumper on terminals “C-AS”. N° C3762 WIRING DIAGRAM OF ELECTRIC DOOR-OPENER SYSTEM WITH CALL SYSTEM "SOUND SYSTEM", CONVERSATION PRIVACY, DIRECT LOCK RELEASE AND FOR NOTICE OF CALL IN DOOR ENTRY PANEL. 4 RELAY Art. 170/101 POWER SUPPLY Art. 931A/C17 PHONE Art. 8878 MAINS PRI 1 2 3- C2 6 7 8 C1 CP O 15 AS 1 2 3 4 5 1 2 3 6 6E 7 8 PHONE Art. 6200 + 6155 + 6152 C A 7 AU 1 2 3 5 6E 6 6P 6S AU 1 2 CN1 3 6E E A L1 3 4 5 6 7 8 4 8 1 2 3S CH B D R C AC C AS BL BI RO A+ A- A- Entrance panel series Patavium 8000, 8100, 1200, 3300 B- Additional push-button for lock C- Electric lock 12V∼ D- Outdoor unit Art.930, 930A L1- Bulb for panel lighting (3x24V 3W max.) 10x24V 3W with Art. 832/C17 16X24V 3W with Art. 832/3C7 Art.8878 N.B. On interphone Art. 8878 displace jumper on terminal “AC-C”. N° C3763 WIRING DIAGRAM OF ELECTRIC DOOR-OPENER SYSTEM WITH CALL SYSTEM "SOUND SYSTEM", CONVERSATION PRIVACY, LOCK RELEASE AFTER THE CALL AND FOR NOTICE OF CALL IN DOOR ENTRY PANEL. 5 A- Entrance panel series Patavium 8000, 8100, 1200, 3300 B- Additional push-button for lock C- Electric lock 12V∼ D- Outdoor unit Art.930, 930A L1- Bulb for panel lighting (3x24V 3W max.) 10x24V 3W with Art. 832/C17 16X24V 3W with Art. 832/3C7 POWER SUPPLY Art. 931A/C17 PRI 1 2 3- C2 6 7 8 C1 CP O 15 AS MAINS A L1 PHONE Art. 8870 B B 1 2 3 4 5 6 7 8 3 4 5 6 7 8 D ELVOX C N.B. IN CASE OF NOISE IN THE AUDIO MOVE, IN THE POWER SUPPLY, THE WIRE CONNECTED ON THE DOOR LOCK TERMINAL N. 15 TO TERMINAL AS. PHONE Art. 620R B 1 2 3 4 5 6 7 1 2 3 S CH N° C3694 WIRING DIAGRAM OF ELECTRIC DOOR ENTRY SYSTEM WITH “A.C.” CALL AND CALL ON DOOR ENTRY PANEL. 6 VARIAZIONI DEGLI SCHEMI BASE VERSIONS FROM STANDARD WIRING DIAGRAMS VERSION 1 POWER SUPPLY Art. 931A/C17 Connection of outdoor call push-button. When activating the outdoor push-button the phone sounds with a tone different from the one obtained by the external entrance panel call. MAINS PHONE Art. 8875 Art. 8878 Art. 6200 (6P) A- Outdoor push-button (6P) VERSION 2 POWER SUPPLY Art. 931A/C17 Connection of the call repeater Art. 2/841. The loudspeaker module Art. 2/841 repetes the phone sound leaving the tone unaltered. MAINS PHONE Art. 8875 Art. 8878 Art. 6200 (6P) (6S)(6P) Call repeater Art. 2/841 VERSION 3 RELAY Art. 170/001 POWER SUPPLY Art. 931A/C17 Connection of stair-lighting push-button by using repeater relay Art. 170/001. MAINS STAIR-LIGHT PUSH-BUTTON Max. load 3A-230V PHONE Art. 8875 Art. 8878 Art. 6200 (6P) Art. 8870 N.B. To switch on stair-light press push-button with bulb symbol . The maximum capacity of the phone button contacts is 24V 0.5A A.C./D.C. VERSION 4 Connection of additional bell. RELAY Art. 170/101 Max. load 3A-230V 12V∼ additional bells can be fitted using the relay Art. 170/101 connected as shown in the diagram. Bell supply PHONE Art. 8875 Art. 8878 Art. 6200 (6P) (6S) 7 MINIMAL CONDUCTORS SECTION FOR DOOR ENTRY SYSTEMS (mm2) Tipical section Terminals a b Ø up to 50 m. 0, 3, 12, 15, -, AS, S1 C1, C2, C3, P1, P2 lock, calls 0,5 mm others 0,25 mm Ø up to 100 m. 2 0,75 mm 2 Ø up to 200 m. 2 2 1,5 mm 2 2 0,5 mm 1 mm Conversion table of sections-diameters and relative resistances for 100 m. standard conductors. Section mm2 0,12 0,25 0,35 0,50 0,75 1,00 1,50 2,50 4,00 6,00 Diameter mm. 0,40 0,58 0,68 0,80 1,00 1,15 1,40 1,80 2,30 2,80 AWG 26 23 22 20 18 16 14 12 10 Decimal diameter 4/10 6/10 8/10 10/10 12/10 14/10 18/10 Resistance Ω 100m. 14,00 6,60 3,50 2,20 1,70 1,14 0,69 4,80 0,39 0,28 FILIALI ITALIA FILIALI ESTERE Padova ELVOX Austria GmbH Via A. Ferrero, 9 35133 Padova Grabenweg 67 A-6020 Innsbruck Torino ELVOX Shanghai Electronics Co. Strada del Drosso, 33/8 10135 Torino 3. Floor No. 2 Bulding No. 1898 Lai Yin Road Hi-Tech Park SongJiang, Jiu Ting District Shanghai 201615 Milano Via Conti Biglia, 2 20162 Milano CERT n° 9110.ELVO ELVOX Costruzioni elettroniche S.p.A. - ITALY Via Pontarola, 14/a - 35011 Campodarsego (Padova) Tel 049 9202511 - Fax 049 9202603 - info@elvox.com Telefax Export Dept. +39/049 9202601 - elvoxexp@elvox.com www.elvox.com UNI EN ISO 9001:2008
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2013:11:13 14:20:51+01:00 Modify Date : 2013:11:13 14:20:51+01:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2013:11:13 14:20:51+01:00 Format : application/pdf Document ID : uuid:64f456b4-50e6-4739-95f5-423e05abec7c Instance ID : uuid:5e40d094-383c-4507-80b6-80d55fc9ba7b Page Count : 8EXIF Metadata provided by EXIF.tools