AA D783B TB_Remote_Station_Guide_Jul82 TB Remote Station Guide Jul82

AA-D783B-TB_Remote_Station_Guide_Jul82 AA-D783B-TB_Remote_Station_Guide_Jul82

User Manual: AA-D783B-TB_Remote_Station_Guide_Jul82

Open the PDF directly: View PDF .
Page Count: 116

Download
Open PDF In Browser	View PDF

TOPS-10
Remote Station Guide
AA-D783B-TB

July 1982

This manual is for use at a PDP-11-based remote station that
has access to a TOPS-10 host. It contains information on both
hardware and software for users and remote station operators.
This manual supersedes the TOPS-10 DN200 Remote Station
Guide, AA-D783A-TB.
OPERATING SYSTEM:
SOFTWARE:

TOPS-10 V7.01
CHK11 V3(66)
DN82/DN200 V23(152)
NETLDR V3(144)
OPR V4(344)
GLXLlB V1 (767)

Software and manuals should be ordered by title and order number. In the United States, send orders
to the nearest distribution center. Outside the United States, orders should be directed to the nearest
DIGITAL Field Sales Office or representative.

Northeast/Mid-Atlantic Region

Central Region

Western Region

Digital Equipment Corporation
PO Box CS2008
Nashua, New Hampshire 03061
Telephone:(603)884-6660

Digital Equipment Corporation
Accessories and Supplies Center
1050 East Remington Road
Schaumburg, Illinois 60195
Telephone:(312)64Q-5612

Digital Equipment Corporation
Accessories and Supplies Center
632 Caribbean Drive
Sunnyvale, California 94086
Telephone:(408)734-4915

digital equipment corporation. marlboro. massachusetts

First Printing, October 1978
Revised, July 1982

Copyright ©, 1978, 1982, Digital Equipment Corporation. All Rights Reserved.

The information in this document is subject to change 'without notice and should
not be construed as a commitment by Digital Equipment Corporation. Digital
Equipment Corporation assumes no responsibility for any errors that may
appear in this document.
The software described in this document is furnished under a license and may
only be used or copied in accordance with the terms of such license.
No responsibility is assumed for the use or reliability of software on equipment
that is not supplied by DIGITAL or its affiliated companies.
The following are trademarks of Digital Equipment Corporation:
DEC
DECUS
DECSYSTEM-20
DECwriter
DIBOL
EduSystem

~D~DDmD

DECnet
DECsystem-10
PDT
RSTS
RSX
VMS
RT

lAS
MASSBUS
PDP
UNIBUS
VAX
VT

The postage-prepaid READER'S COMMENTS form on the last page of this
document requests the user's critical evaluation to assist us in preparing future
documentation.

CONTENTS

CHAPTER 1
1.1
1.1.1
1.1.2
CHAPTER 2
2.1
2.1.1
2.1.2
2.1.3
2.1.4
2.1.5
2.1.6
2.1.7
2.1.8
2.1.9
2.2
2.2.1
2.2.2
2.2.3
2.2.4
CHAPTER 3
3.1
3.2
3.3
3.4
CHAPTER 4
4.1
4.2
APPENDIX A

INTRODUCTION
TOPS-10 REMOTE STATIONS AND CONCENTRATORS
. . . . 1-1
The DN80-Series Remote Station and Concentrator 1-2
The DN200 Remote Station . . . . . . . . . . . . 1-2
OPERATOR PROCEDURES
STARTUP . . . . • • • . . . . • • . . . .
. 2-1
Starting the Station • . • • . . • . • . . . . . 2-2
Restarting the Station . . . . . . . . . .
. 2-3
Logging in at the TOPS-10 Host from the Remote
Station . . . • . • • • . . . • . . . . . . . . 2-4
The Operator Interface . . . . . • . . . . . . . 2-5
Relocating Your Station Devices
. . . 2-8
Starting Printer Scheduling
. . . . . 2-9
Starting Card Reader Scheduling • . . . . . . . 2-9
Starting Both Printer and Card Reader
2-10
Scheduling . . . . . • • . .
2-10
Using OPSER . . . • . . . . .
2-11
AVAILABLE EQUIPMENT . . . . . . . . . .
2-11
LA36, the Operator's Console.
2-13
Card Reader
2-16
Printer
2-18
Terminals
• • . . . . . .
USER PROCEDURES
USER FACILITIES
. . .
THE NETWORK COMMAND . . • . .
PRINTING OUTPUT . • . . . . • . . .
SUBMITTING BATCH JOBS
. . • . . . .

.
. . . .
. . . • . . •
. . .
.

3-1
3-2
3-2
3-3

TROUBLE-SHOOTING
NORMAL OPERATION
WHEN PROBLEMS OCCUR
ROM SWITCHES

iii

. . . 4-1
4-2

CONTENTS (Cant.)

APPENDIX B
B.1
B.2

NETLDR COMMAND STRINGS
DEFAULT LOAD REQUESTS
LOADING EXAMPLES . . .

.
• .

APPENDIX C

PUNCHED CARD CODES

APPENDIX D

GLOSSARY

APPENDIX E

REMOTE STATION OPR COMMANDS

APPENDIX F

USING SPECIAL PRINT FORMS

. B-2
. B-2

FIGURES
FIGURE

1-1
1-2
1-3
1-4
2-1
2-2
2-3
2-4
2-5
2-6
2-7
B-1
B-2
C-1

The DN82 Remote Station
• • • • . • • . ••
DN82 Control Panel . . .
· .
The DN200 Remote Station • • • • •
• • •
DN200 Control Panel
• • •
The System Operator
· . ..
......
The Host Operator
• • • • •
The Remote Operator
•
Card Reader
. . • •
Front Panel of Card Reader .
Back Panel of Card Reader
LP05 Line Printer
.•..
A Default Load Path
.......••.
Using an Alternate Load Path . . . . . . .
A Punched Card . . . . • • . • .
·

• 1- 2
. . 1-2
• . 1- 2
• . 1- 3
. 2- 6
• • 2- 6
• • 2-6
2-14
2-14
2-15
2-17
B-2
· B-3
. . C-1

TABLES
TABLE

1-1
2-1
2-2
2-3
2-4
2-5
4-2
A-I
B-1
C-1
C-2
E-1
E-2
E-3
F-4

Remote Station Components
Mode and Baud Rate Switches
Console Lamps
Card Reader Switches and Lamps
Card Reader Back Panel Switches
Printer Alarm Indicators
Station Messages
Remote Station ROM Switches
NETLDR Bootstrap Switches
ASCII Character Set
ASCII Characters by Punched Rows
OPR Command Functions
OPR Objects
OPR Commands
LPFORM. INI Switches

·····

··
··· ·
····

. .···
..··

iv

·
·

·
·
· · ·· ·· ·
·· ·
· ·
···
··
·
·
···
·····
·
· · ·· ·· ·

·
·
· · ··
· · ··
··
···
··
·· ··

·

1-1
· · ·2-12

· ··

2-13
2-14
2-15
2-18
4-3
A-I
B-1
C-2
C-5
E-1
E-2
E-4
F-1

··
···
· ·
·· · ·
· · ··
·
·

PREFACE

This ~uide provides information on using and operating PDP-II-based
remote stations that can be connected to a host system running
TOPS-IO.
Everyone using the remote station should read Chapter 1,
"Introduction":
operators
should
read
Chapter
2,
"Operator
Procedures," and Chapter 4, "Trouble-Shooting." Users can benefit from
reading Chapter
3, "User Procedures," Sections 2.1.3, "Logging in at
the TOPS-IO Host from the Remote Station," and 2.2.4, "Terminals." The
appendixes contain descriptions of ROM switches, the NETLDR program,
how to read dump files, punched card codes, a glossary, procedures for
using special print forms, and OPR commands that can be issued at a
remote station.
SUPPORTING DOCUMENTATION
Not all the TOPS-IO Software Notebooks will normally be
the remote site, but the following documents should be:

available

Getting Started with DECsystem-lO
(TOPS-IO)

[DEC-IO-XGSDA-A-D]

Operating System Commands Manual

[AA-0916D-TB]

The following documents describe other aspects of the system:
Networks Software
Installation Guide
and its update

[AA-5156E-TB]
[AD-5156E-TI]

TOPS-IO/TOPS-20 Batch Reference Manual

[AA-H374A-TK]

Operator's Guide
and its updates

[AA-H283A-TB]
[AD-H2 8 3A-TI]
[AD-H28 3A-T2]
[AD-H283A-T3]

Operator's Command Language
Reference Manual

[AA-H599A-TB]

DDTll Manual

[AA-J495A-TB]

INITIA System Initialization CUSP

[Software Notebooks]

v

at

NETLDR Remote Node Load and
Dump Utility

[Software Notebooks]

OPSER Operator Service Program

[Software Notebooks1

CHKII Reference Manual
[Software Notebooks]
(System Programming Procedures and Techniques)
The following symbols have been used in this manual:
Symbol

Meaning
The RETURN key on the operator's console.
The TOPS-IO prompt character.



A key on the DN82 or DN200 control panel.
"is

Symbol
indicates
specifications) .

defined

as"

(in

syntax

Required space in syntax specifications.
[]

An optional entry (in syntax specifications).
An entry of the previous
syntax specifications).



type

can

be

repeated

An entry in syntax specifications.
Grey-shaded entries pertain to the DN200 only.

red
print

What you type on your terminal.

black
print

In examples, the system response.

vi

(in

REVISION HISTORY

This manual supersedes the TOPS-IO DN200 Remote Station Guide.
It
provides guidance for using and operating PDP-II-based remote stations
connected to a TOPS-I0 host system.
It further provides extensive
information on remote stations and concentrators, with specifics on
two types:
1.

The DN80-series remote station and concentrator

2.

The DN200 remote station and concentrator

The major differences between this manual and the one preceding are
the updating of TOPS-I0 Version 6.03A to TOPS-I0 Version 7.01, and the
resulting software updates:
CHKll
DN82/DN200
NETLDR
OPR
GLXLIB
GALAXY

Version
Version
Version
Version
Version
Version

3 (66)
23 (152)
3 (144)
4 (344)
1 (767)
4.1

The previous manual did not include details on the Operator Interface
which is a new feature of the GALAXY system. It also did not include
the following essential Appendices:
"Glossary"
"Remote Station OPR Command"
"Using Special Print Forms"
This manual eliminates the Appendix, "Reading Dump Files," that was in
the previous manual.
Information about the GALAXY batch and spooling system is also updated
to reflect changes from Version 2 to Version 4.1. Some of those
changes are discussions on OPR found in this manual:
1.

2.

"The Operator Interface," Section 2.1.4
a.

System Operators

b.

Host Operators

c.

Remote Operators

"Remote Station OPR ommands," Appendix E covers OPR
available to operators.

vii

commands

CHAPTER 1
INTRODUCTION

1.1

TOPS-lO REMOTE STATIONS AND CONCENTRATORS

Two types of remote stations/terminal concentrators based on PDP-II
hardware can be connected over a synchronous line to a host system
running TOPS-10. When these remote stations contain terminals, they
are also called remote concentrators. The DN82 is a remote station
and concentrator based on a PDP-11/40;
as a remote station alone
(containing only a card reader and a line printer), it is called a
DN80i
as a concentrator alone, it is called a DN81. The DN200 is a
remote station and concentrator based on a PDP-11/34.
A systems programmer or installer at the TOPS-10 host assembles the
software for each remote station, and stores the resulting binary file
on disk at the host.
(Assembly of the software at the TOPS-10 host
site is described in the Networks Software Installation Guide.) An
operator at the remote station can then initiate a request to the
TOPS-10 host to down-line load the remote station software over the
synchronous line.

~.· i.· .:~.· · ~ ~ g. •~.:. !~.{~.~.~. ~ .}~ .:~.:.;.:. ·~.~;e::?"·~~,;,

A.t.···.!.·Sk
. :..;• . . •.·. · • •.

•.;.;.'..

. . ..

:i~~~~~~~~1~'·~f

P.:...

".
.h
t'urns~.;:
'fts ROM ~~ar ts to execute. The ROM sends a carr lage""~~:t'u,p:1:;a,n:~~;1'~n~:;
.f'~e:d :to'yourqonsole and wai ts .for you to tYPf::;! OIl tlle;99nsole:;' ,,~,',":,:::;;:'~:::;i
After you turn on your DN80-series remote station, you can start it at
its starting address.
When you enter its starting address, its ROM
bootstrap program starts to execute. You can type switches to the ROM
and/or a command string to be forwarded to NETLDR.
(ROM switches are
described in Appendix A; NETLDR commands, in Appendix B.) With ROM
switches, you can specify a synchronous line number, a host node
number, and a remote station serial number, or you can also use all
defaults.
The
command string for NETLDR can contain a file
specification and switches to specify whether to load, or to load and
start the remote station.
When you type on the console, use the
following form:
command ::= 
To use all defaults (that is, to use a predefined set of switches and
NETLDR command string), press ~ or wait (about two minutes) for
the station to time-out and send the default load request.

2-2

OPERATOR PROCEDURES
When you type ROM switches and a NETLDR command string,
type ROM
switches first.
If you enter ROM switches and NETLDR switches
together, separate the two types of switches with a space.
NOTE
Always follow ROM switches with a space,
even when not entering NETLDR switches.
To correct a typing mistake before you press ~ ,press the DELETE
key to delete the entire line.
If you make an error and do not
realize it until after you have pressed ~, either wait until you
get an error message and enter the correct values or use the restart
procedure.
After you type in NETLDR switches and press
~,
current console
type-in at your remote station ends. When console type-in ends, the
ROM sends a load request to an adjacent node alpng the synchronous
line you have selected. The adjacent node then attempts to load your
remote station.

As your DN80-series remote station starts, and as the DN200 continues,
you obtain output from the hardware-checking program, CHK11, a
"STARTING" message, and the TOPS-10 host prompt as follows:
Initializing ON200 V21(131) 25-0ec-79--CTCH22(22)
100000 bytes of memory
MF11-UP
KW11-L
KG11-A
1 OL11-A
1 CR11
1 LP11
LP11 #0 Not ready
2 OM11-BB's
2 OH11's
2 OQ11's
Restarting ON200 V21(131) 25-0ec-79--CTCH22(22)
Host is available.
For more information on CHK11, see the CHK11 Reference Manual.

2-3

OPERATOR PROCEDURES
2.1.2

Restarting the Station

At a DN80-series station, once your station has been loaded, started,
and has been successfully running, it continues to run until a power
failure or a software
crash
occurs.
The
station
recovers
automatically from these conditions, generally being reloaded from the
host site whenever necessary.
To restart your station manually, be sure the power is on and press:
ENABLE/HALT
address LOAD ADRS
START
You must enter the starting address in the switch
Switch Register switches.

register

with

the

AtaDN2 00, once your station hGis been loaded,sta'rte"d','a;nd" ;:tl'a's::'::;:beeri'
succ~ssfUlly
running l i t can bE; restarted using the s\'l~ tc.n~~,pn;~J:l~,:
8ontrQl,panel of the DN200 (see Figure 1-4).
,;'
'~"
<

":

To restart your DN200 remote station, be sure the:pqwE;r
and Press;
 
"addr '

The valu€of "addr ", is the starting address of the r~m6'te'S#~~~c>if'i
software. « To determine  <<

24 
<'EXAM>

Halt the DN200.
Clear the DN20() switch regist:er.::
Load 24 into t,hesw,itchregistet'.: ,«<'
<
Press the EXAMINE swi tch ,to', 'examine.: "tji~i
contents of locat ion 24.
,
The value displayed (0000, 240?,'or:'sO'IJie'oihfi,:i;
value) is the starting address."
"'"
,,;'
Load the starting addre$s~
"
Start the DN200 at the ente
 

2.1.3

:'

Logging in at the TOPS-IO Host from the Remote Station

To use your operator's console and issue any commands, you must log in
at the TOPS-IO host. To do so, you must see the TOPS-IO prompt (.) on
the console. The prompt normally appears automatically as soon as
your station comes up. If the system operator at the host has set up
your TTY.INI commands to do so, the INITIA program logs you in to your
operator directory (project-programmer number) and you can proceed
simply by typing I ~ on your terminal.
If you do not see the TOPS-IO prompt, follow these steps:
1.

Check your console. It must be on and filled with paper.
The switches on the left side, except for the '300' switch,
should all be in the 'up' position. The '300' switch should
be down.
2-4

OPERATOR PROCEDURES
2.

«

TRL/9
Press
The TOPS-IO
following type of message:

prompt

appears

below

the

Host is available.
Connecting to host system.
---System herald---TTY215 system ...
Connected to Node CTCH22(22) Line #0
DSKB:

3.

Type the word LOGIN and press
number prompt (#) appears.

4.

Type

~

on

your

terminal.

A

your project-programmer
number
(PPN)
and
press
(Remote station operators often log in under the
[PPN]=[lnn,2], where nn is their station number [also called
node number].)
To determine your PPN, contact the System
Administrator. The Password: prompt appears.
~.

5.

Type your password, which is not printed, and press ~
on
your terminal.
(You can abbreviate these steps by typing
LOGIN PPN password ~ ).

6.

The TOPS-IO host then sends you a message containing the
time,
the date, and the day of the week. You may also
receive system messages sent from the central site.
The
TOPS-IO host may also run OPR, the operator interface, for
the OPR prompt, OPR),
you automatically.
In this case,
appears.

7.

You are now logged in and can perform your normal duties.

The following lines illustrate your output:
. LOGIN
#172,2
Password:
12:00
11-Sep-80

Thur

or
.LOGIN 172,2
.R OPR
OPR)
The operator's console at the remote station must be
filled with paper whenever the station is operating.

2-5

kept

on

and

OPERATOR PROCEDURES
2.1.4

The Operator Interface

In a TOPS-IO network, there can be three types of operators, each with
specific privileges.
The system administrator at the host assigns
these privileges to your operator's PPN with the system program REACT.
As a remote station operator, you obtain these privileges when you log
in with your operator's PPN.
The three types of operators are:
•

System operators

•

Host operators

•

Remote operators

A system operator has the most global privileges and capabilities.
The system operator can control all devices anywhere in the network
controlled by his host, both at the central site and at remote sites.
An operator who logs in as
[1,2]
automatically receives system
operator privileges.
(See Figure 2-1.)

,-----------------,
I

I

I

I

I
I

I
I

I
I

I
I

I

'

I'

,,,-~..

THE
SYSTEM
,
OPERATOR

1

~~J

'--J'_

I

DOMAIN OF
THE SYSTEM OPERATOR

,

L ________________

.-l

MR-S-1110-81

Figure 2-1

The System Operator

A host operator is an operator who can control all devices at the host
where he is physically located.
He cannot control devices at any
other host or at any remote node.
(See Figure 2-2.)

1--I

,

,
I

THE
HOST
I
OPERATOR,

.:.r_,1
'r-~"

;~-:

,.

L __

-=:--J

,
,

I

I
__ --.J

Figure 2-2

DOMAIN OF
THE HOST OPERATOR

The Host Operator
2-6

OPERATOR PROCEDURES
A remote operator can control all devices at the remote node where his
terminal
is connected; he cannot control devices at the central host
or at any other remote node.
(See Figure 2-3.)
DOMAIN OF
THE REMOTE OPERATOR

.---------,

,;;.:!....: I THE
O~REMOTE
.
I OPERATOR

I

I
I
I

--J

I

I
I

L______ --'

MR-S-1112-81

Figure 2-3

The Remote Operator

As the operator at a remote station, you run OPR to control your local
line printer and card reader, and perform any other operator duties.
OPR is the Operator
Interface through which you communicate with
ORION.
ORION,
in turn, communicates with other components of GALAXY
and the TOPS-IO operating system.
You issue commands to OPR to
communicate with the TOPS-IO operating system, to control the devices
at your remote station, and to control the jobs that are sent from and
received at your remote station.
If your host does not automatically start OPR for your remote station,
you can start OPR with the following commands.
To run aPR you must be
logged into a privileged account .
. R aPR @)
The system returns the aPR prompt:
aPR>
See Appendix E for descriptions
remote operators.

of

the

OPR

commands

At the TOPS-IO host, the operator runs LPTSPL and CDRIVE.
spoolers at the host support the devices at your station.

available
The

to

usual

As you issue aPR commands, they are sent to ORION.
ORION puts a
timestamp on each command, logs the command in the operator's log file
(normally stored in [3,3]OPERAT.LOG) , and executes the command.
When
execution is complete, ORION sends you a message of the following
form:
hh:mm:ss

aPR object

--action--

or
hh:mm:ss

--informational message--

2-7

OPERATOR PROCEDURES
For example, when you issue a
following prompts appear:
OPR> START (object)
OPR>
hh:mm:ss Printer a
OPR>

command

to

start

PRINTER (Unit Number)

a

your

printer,

the

~

[nodename (node number)]--Startup Scheduled--

If you misspell an OPR command, or give an
incomplete command,
an
error message preceded by a question mark appears.
OPR error messages
of this type are all self-explanatory.
You can obtain the valid part
of an incorrect command by pressing
(CTRL/~
For example, say you
are running OPR and issue the following incomplete command:
C~D

OPR> SHOW STATUS P

OPR sends you the following message:
OPR>SHOW STATUS P
?CONFIRMATION Required
OPR>
If you type

(CTRL/0

, the valid part of the command appears:

OPR>
0~~~
OPR> SHOW STATUS
You can type?

to see what arguments are valid.

OPR> SHOW STATUS? one of the following:
BATCH-STREAM
NETWORK-NODE
PRINTER
OPR>SHOW STATUS

READER

In addition, you may use escape recognition when typing OPR commands.
The ESCape key allows recognition input and guide words to appear on
your console when you give an OPR command.
The ESCape key may be labeled ESC, SEL, PRE, or ALT, depending on the
type of console terminal your installation is using.
Type the OPR
command START with the use of the ESCape key for recognition and guide
words.

.

CESe)

G~

~

a

OPR> START (object)

PRINTER (uni t number)

OPR>
hh:mm:ss Printer

[nodename (nodenumber)]--Startup Scheduled

a

CRET-)

OPR>
If the terminal bell rings, you have not typed enough characters to
identify a command.
If this happens, type another character
of the command and press the ESCape key.
Continue to do this until
the characters you typed are unique for the specific command.
uni~uely

2-8

OPERATOR PROCEDURES
The operations that you can perform with OPR at
include:

2.1.5

your

remote

•

scheduling jobs for your devices

•

suspending the scheduling of jobs

•

setting parameters for your devices

•

displaying the status of devices and jobs

•

canceling jobs

•

controlling output on your printer

•

enabling and disabling the display of system messages

station

Relocating Your Station Devices

You can use the LOCATE monitor command to specify another node as your
logical node, to establish your job at that node.
Type the following:
LOCATE node number

~

The node number is the number of the node where you want to locate the
input/output devices for your
job.
It must be a node number
recognized by the host.
It acts as the default node number for all
subsequent PRINT and SUBMIT commands.
You can verify the node number
for the other node with the NETWORK command, which lists all nodes
defined in the network.
After giving the LOCATE command, you can have
devices at the new logical node perform the input and output for your
jobs.
For example, the following command relocates input and output
at node 22 (not your node):
.LOC 22 ~
Node CTCH22 (22)

DN82

V23(152)

16-Jan-81

Located

To relocate devices at your own physical location, reissue the
monitor command with no arguments.

LOCATE

If, during your session, the node to which you have LOCATED becomes
inaccessible, you are returned to your physical location.
You can use
the SHOW STATUS NETWORK-NODE or the NETWORK command to check on other
nodes in your system.
As a remote operator, you cannot execute the ROUTE command to direct
output to ~nother node in the system. You must ask the operator at
the host to perform routing.
You may wish to have some or all of your
output routed to another node if, for example, your line printer is
out of service or a job requires special forms not available at your
node.
(See also Appendix F, Using Special Print Forms.)

2-9

OPERATOR PROCEDURES
2.1.6

Starting Printer Scheduling

Before you start scheduling jobs for your printer, the TOPS-10 host
operator should have a copy of LPTSPL (the line printer spooler)
running. One copy of LPTSPL can handle up to 15 local and remote
printers. Only the TOPS-10 host operator can start the spoolers. You
can issue commands to start scheduling at any time, but requests are
processed only if the spoolers are running. To verify that LPTSPL is
running, type the following:
~;YS

[1,2]

C~E~.J

All the OPR jobs running on the host are listed;
LPTSPL should
among them. If not, contact the system operator at the host.

be

For example:
.SYS [1,2]CRET )
1
DET
INITIA

11

DET

LPTSPL

6+11

SL

8

37+34

HB

1:00

This runs the SYSTAT program to display jobs on the system.
To run OPR and start printer scheduling, follow these steps:
1.

At the OPR prompt,
scheduling.

type

START

2.

Verify that your printer is on.

PRINTER

0

~

to

start

The following lines illustrate your output:
. H OPR (RET)
OPR) START PRINTER 0 (~0
OPR)
hh:mm:ss Printer 0 [nodename (node number)]--Startup Scheduled-OPR)

2.1.7

Starting Card Reader Scheduling

Before you start scheduling jobs for your card reader, the TOPS-10
host operator must have a copy of CDRIVE (the card reader spooler)
running. One copy of CDRIVE can handle up to 15 local and remote card
readers.
To start scheduling for your card reader, you
with OPR.

2-10

must

also

communicate

OPERATOR PROCEDURES
To start scheduling, type the following:
R OPR @)
1.

At the OPR) prompt, type
START READER 0 @)

2.

Verify that your card reader is on.

Your output will look as follows:
OPR)START READER 0
OPR)
hh:mm:ss Reader 0 [nodename (node number)]--Startup Scheduled-OPR)

2.1.8

Starting both Printer and Card Reader Scheduling

You can run OPR at your remote station to start
the printer and card reader as follows:

scheduling

for

both

. R OPR@)
OPR) START PRINTER 0 ~
OPR)
hh:mm:ss Printer 0 [nodename (node l1umber)]--Startup Scheduled-OPR) START READER a ~
OPR)
hh:mm:ss Reader 0 [nodename (node number)]--Startup Scheduled-OPR)
The system operator at the host can also place printer and card reader
commands in the system file [1,4]SYSTEM.CMD. This file is called with
a TAKE command from the system file [1,4]OPR.ATO. With your startup
commands in a system file on the host, scheduling for your devices
should occur automatically.
If not, contact the system operator at
the host.
For more information on OPR, see Appendix E,
"Remote Station
Commands," and the Operator's Command Language Reference Manual.

2.1.9

OPR

Using OPSER

Generally, you should run OPR at your operator terminal and perform
other, duties from another terminal.
However, if you wish to use your
operator terminal for several functions,
you can use OPSER.
With
OPSER you can run up to 14 subjobs from a single terminal.
(For more
information on OPSER, see the OPSER help file (type HELP OPSER
@)
or see the TOPS-10 Operating System Commands Manual.)
To use OPSER to run OPR and perform some other functions, follow these
steps:
1.

Type the following:
R OPSER

~

This runs the OPSER program and initiates an OPSER job.
OPSER prompt (*) appears.

2-11

The

OPERATOR PROCEDURES
2.

Type the following:
: LOGIN PPN

CRI!:)

(Commands to OPSER always start with a colon.) Use your own
PPN.
This logs in a subjob which you will use to run OPR.
Output of the following form appears:
h h : mm : s s (0 )
Job xx
[LGNJSP
hh:mm:ss
[

3.

system name
TTYno.
Other jobs same PPN:xx]
date day

]

Type:
: DEFINE OPREM=

C~i)

This names your subjob OPREM.
(You can use another name
it cannot contain more than five characters.)
4.

but

Type:
OPREM-R OPR

~

(Commands to OPSER subjobs do not need colons.)
This loads
OPR under control of the subjob.
Output of the following
form appears:
*OPREM-R OPR
!hh:mm:ss
(OPREM)
OPR>

5.

Enter OPR commands for your remote station devices.
The help
facility is also available to you at this command level.
Precede each command with the name of your subjob followed by
a hyphen.
For example,
OPREM-START PRINTER 0

~~)

or
OPREM-START READER 0
6.

To issue more commands ,to OPSER, precede each
(:)

7.

2.2

~~!.)

.

wi th

a

colon

To see the state of each of your subjobs, use :WHAT ALL.
To
kill all your subjobs,
use :KILL ALL.
To kill a specific
subjob, use :KILL subjob-name.

AVAILABLE EQUIPMENT

The typical TOPS-IO remote station contains an operator's console
(LA36);
it can also contain a card reader, a line printer and user
terminals.
These pieces of equipment are briefly described
in this
chapter and
in supporting hardware documents that are provided with
your equipment.

2-12

OPERATOR PROCEDURES
2.2.1

LA36, the Operator's Console

Your operator's console is an LA36, a 30-character per second printer
with a keyboard. To turn your console on, press the rocker switch on
the left side of the keyboard to the on position. All the switches on
the left side of the keyboard except for the one labeled '300' must be
in the 'up' position. The '300' switch must be pressed down.

NOTE
Your LA36 must always be filled with
paper or you may lose data when it goes
into a paper-out condition.
Check the
paper supply periodically and replenish
it before it runs out.
The switches at the left of the keyboard are two-position switches
(like the shift-lock key on a typewriter) and indicate operating mode
and baud rate as listed in Table 2-1.

2-13

OPERATOR PROCEDURES
Table 2-1
Mode and Baud Rate Switches

Indicates

Up/Down

Up

Console communicating on its asynchronous line.

Down

Console in local state.
asynchronous line.

Up

Communication is full-duplex (normal mode on line to
DN200) .

Down

Communication is half-duplex (not normally used).

No communication occurs on

Down

Up

}

Communication on line to DN200 is at 110 baud.

Up

Down

}

Communication on line to DN200 is at 300 baud
(standard position).

Down
Communication on line to DN200 is at 150 baud.
Down

Up

Standard character set is in use (normal position) .
STD. CHARACTER SET lamp is lit.

Down

Alternate character set is in use.
lamp is lit.

Always
Up

Standard character set is normally used.

Up

LA36 is automatically controlled by DN200 and TOPS-10.

Down

When LA36 is in local mode, paper advances one line when
LF (line feed) switch is pressed.

Always
Up

2-14

ALT. CHARACTER SET

OPERATOR PROCEDURES
Lamps on the operator's console are described below.
Table 2-2
Console Lamps
Lamp

When Lit, Indicates

STD. CHARACTER SET

The standard character set is in
CHAR SET switch is up).

ALT. CHARACTER SET

The alternate character set is in use
(ALT
CHAR SET switch is down).
For normal
operation, the ALT CHAR SET switch must be
up.

PAPER OUT

The LA36 is out of paper.
Replenish the
paper supply.
(Open the inner cover of the
LA36, open the pinfeed gates, thread paper
from below the printer past the gates, and
hook the perforations over the pins. Close
the gates and the printer cover.) To resume
operations, you must either press
the
LINE/LOC.
switch down, and then reset it
in the upper position, or turn your LA36
off then on again.
Data may be lost by
these operations.

DEVICE SELECT

This lamp should always be out.
If on,
call your Field Service representative.

SELECT AVAIL

This lamp should always be out.
If on,
call your Field Service representative.

2.2.2

use

(ALT

Card Reader

The card reader (see Figure 2-4) at the remote station reads 80-column
punched cards at a rate of 285 cards per minute.

Figure 2-4

Card Reader
2-15

OPERATOR PROCEDURES
It has an input hopper (upper right), an optical card-reading station,
an output hopper (lower left), switches to control its operation (on
front panel), and indicator lamps. Toggle switches on its back panel
are used to turn on and set up the card reader (see Figures 2-5 and
2-6) •

r----' r----' r-----' .. ------,

I

POWER

I

I
I

'
'I

,
'I

I

I

PICK :
,CHECK I

I _____ .I,
L

IL _____ JI

I

READ
CHECK

I
I
:

I

;

I

STACK' 'HOPPER I
CHECK: : CHECKl

I STOP I IRESET I

o

IL _____ JI LI _____ J I

0
MR-S-064-78

Figure 2-5

Front Panel of Card Reader

The switches and lamps on the front
explained in Table 2-3.

panel

of

the

card

reader

are

Table 2-3
Card Reader Switches and Lamps
Switch/Lamp

When Lit, Indicates

POWER

Power is on.

None.

READ CHECK

Card just encountered
may be damaged.

Remove
(and repunch)
faulty card and press
RESET.
Reread
the
card.

PICK CHECK

Card just encountered
may be damaged, deck
may be warped or
reader may need
cleaning.

Correct card or deck
condition
and
press
RESET.
Reread
the
card.

STACK CHECK

Card just read may be
damaged, or there may
be a card jam.

Clear jam or repunch
damaged
card.
Press
RESET and reread the
last card.

HOPPER CHECK

Either:
Input hopper is empty
and no EOF card has
been encountered

Corrective Action

Reread the last
followed by
an
card.

card
EOF

Or:
Output hopper is
full.

2-16

Empty the output hopper
and press
RESET
to
continue.
Reread the
last card read.

OPERATOR PROCEDURES
Table 2-3 (cont.)
Card Reader Switches and Lamps
Switch/Lamp

When Lit,Indicates

Corrective Action

STOP switch
and red lamp

Press to stop reading
cards.
Red lamp
is
RESET green lamp
lit,
goes out.

RESET switch and
green lamp

Press to light green
lamp, start blower and
start reading cards.

Figure 2-6 illustrates switches on the back panel of the
and Table 2-4 explains their use.

LAMP TEST

®

card

reader

SHUTDOWN
MAN@ AUTO
MODE
REMOTE

G

LOCAL

MR-S-012-78

Figure 2-6

Back Panel of Card Reader

Table 2-4
Card Reader Back Panel Switches
Switch

Use

POWER

Raise to turn on card reader.

LAMP TEST

Press to light indicators on front panel
faulty lamps).

SHUTDOWN

Set to specify operation of input hopper blower at:

(checks

MANual to operate blower continuously.
AUTOmatic to shut off blower when not
cards.
MODE

for

reading

Set mode to specify on-line and off-line reader
operation at:
REMOTE to place reader on-line under program
control when RESET is pressed.
LOCAL to use RESET and STOP switches to operate
the reader off-line for testing.

2-17

OPERATOR PROCEDURES
To operate the card reader, perform the following steps:
1.

Turn on card reader power.

2.

Load input hopper with cards (face down, column 1
up to 550 cards can be accommodated at one time.

3.

Place the card weight on top of the cards in the hopper.

4.

Press RESET.

You can load and unload cards continuously
operation.

while

the

to

reader

left);

is

in

If you use your card reader almost continuously, clean it once a week.
Wipe the exterior with a soft cloth and vacuum the card dust out of
the card path (turn off the power, blowout the path from the input
hopper to the stacker, and vacuum it).

2.2.3

Printer

An LP05 printer can be attached to your
2-7) .

remote

station

(see

Figure

ALARM
INDICATORS
}
POWER ALARM
ON
CLEAR
READY

ON/OFF
LINE

PAPER
STEP
TOP
OF FORM

FORMS
RESET

••

6lPI

alPI

MAIN POWER
----ON/OFF
CIRCUIT BREAKER

MR-S-006-78

Figure 2-7

LP05 Line Printer

2-18

OPERATOR PROCEDURES
This printer can be either uppercase only or have upper/lowercase
capability.
It uses l32-column pinfeed paper, has a rotating
character drum, and permits forms alignment
(horizontally
and
vertically) and adjustments for forms thickness. Each printer is
provided with a small booklet, an "OPERATORS GUIDE," which describes
how to load and adjust paper and change ribbons. This booklet can be
found in the pocket provided for it inside the cover (lift the cover;
the pocket is on the right side of the drum gate) •
Once you have installed paper and ribbon, you
your line printer. To operate your printer:

are

ready

to

operate

1.

Push the main power circuit breaker (beneath the main
printing mechanism on the front of the printer) to the ON
position.

2.

The POWER ON lamp on the control panel should light up
a few seconds.

3.

If necessary, make adjustments for paper alignment or ink
density (see your "OPERATORS GUIDE" for information on these
procedures) .

4.

Press the ON LINE switch. It should light up. Pr~ssing this
switch places the printer on-line so that it can receive data
for printing. The ON LINE switch must be lit for the printer
to operate.

after

If the ALARM lamp is lit, a malfunction has occurred.
In
such a case, the printer halts and generally goes off-line
(it'stops receiving and printing data).
To restart the
printer you must determine the cause of the malfunction,
correct the problem, press the CLEAR switch (the ALARM lamp
must go out), and press the ON LINE switch. When the ALARM
lamp is lit, lift the printer cover and examine the lamps
above the control panel.
The names of these lamps and
suggested corrective action are listed in Table 2-5, "Printer
Alarm Indicators."
Table 2-5
Printer Alarm Indicators
Lamp

When Lit, Indicates

Corrective Action

HAMMER

A print hammer has
malfunctioned.

Press CLEAR.
The print
buffer is cleared. If the
lamp fails to go out or
reappears, contact Field
Service.

FORMAT

A mechanical malfunction
has caused too many
line feeds. The printer
goes off-line.

Press CLEAR.
Check and
adjust
paper
position,
and push the FORMS RESET
toggle switch (under the
control panel).

RIBBON

A ribbon jam or snag has
occurred. The printer
goes off-line.

Correct ribbon
Press CLEAR.

2-19

feeding.

OPERATOR PROCEDURES
Table 2-5 (cont.)
Printer Alarm Indicators
Lamp

When Lit,Indicates

GATE

Drum gate is not latched.
Printer buffer is cleared.

Latch the gate
and press CLEAR.

PAPER

There is a paper jam,
paper out or paper runaway
condition. The printer
goes off-line.

Fix the paper condition
and press CLEAR.

TAPE

An invalid tape channel
command has occurred.
Printer goes off-line.

Press CLEAR.

2.2.4

Corrective Action
properly

Terminals

You can have many types of terminals attached to your remote station
to operate as user terminals.
The LA36 is described in Section 2.2.1,
"LA36, the Operator's Console." Other terminals are fully described in
their accompanying booklets. The log-in procedure for a video display
terminal is the same as that described for
the operator
in Section
2.1.3, "Logging in at the TOPS-IO Host," (turn on your terminal, issue
the command LOGIN,
respond to prompts with your PPN and your
password) .
To log off the TOPS-IO host, type the following:
K/F~

To exit from an OPSER subjob, type K/F
exit from OPSER, type :EXIT to OPSER.

~

to the OPSER subjob.

To

The TOPS-IO host sends a sign-off message of the following form:
Job 40 User OPERATOR [172,2]
Logged-off TTY235 at 11:06:31 on 25 Dec-79
Runtime: ... KCS: ••. Connect time: .•.
Disk Reads: ... , Writes: ... , Blocks saved: •••
Do not turn off your CTY even after you log off so that
available to receive messages sent to the remote site.

2-20

it

remains

CHAPTER 3
USER PROCEDURES

3.1

USER FACILITIES

A user at a remote station with a terminal has access to all the
system commands and programs that are available to a user at a TOPS-IO
host. The remote site user can also use the physical facilities at
the host, such as magnetic tapes and plotters, by issuing the
appropriate commands and making requests to the operator at the host
site.
Users at remote sites with a card reader can also submit jobs
on punched cards.
For information about TOPS-IO commands and system programs, see the
TOPS-IO Operating System Commands Manual;
for
information about
commands on punched cards and use of the batch system, see the
TOPS-IO/TOPS-20 Batch Reference Manual.
Use the normal log-in procedure to log in on the TOPS-IO host from a
remote station.
For example, your output might look as follows after
completion of login:

Host is available.
Connecting to host system.
--- SRIO --- 10:43:10
TTY2l2 system
Connected to Node CURLY (47) LINE# 2
Please LOGIN or ATTACH
.LOGIN PPN ~
JOB 61 RZ51B --SRIO-- TTYxx
Password:
12:00
5-May-80
Mon

If the system herald is not for the host where you wish to log in, use
the SET HOST command to connect to the right host as follows:
.SET HOST 71 ~
---KLI090--- 10:54:06 TTY212 system
Connected to Node CTCH22 (22) Line # 2
Please LOGIN or ATTACH

To see the node numbers for other network nodes, use the
command.

3-1

NETWORK

USER PROCEDURES
3.2

THE NETWORK COMMAND

To see what nodes are in the network, use the NETWORK command:
. NETW
Node
Node
Node
Node
Node
Node
Node
Node

C~~D

KLI026
KS4101
KI514
SOFDCP
TWINKY
CTCH22
NOVA
JINX

(26)
(76)
(14 )
(77)
(71 )
( 22)
(31 )
( 34)

RZ51B KL #1026/1042 05-14-80
RS051A KS #4101 05-14-80
RX051A KI #514/546 05-14-80
DN82 V20C(E)
Twinky 701/021C 04-10-80
DN82 V21 (131)
25-Dec-79
DN87S V22(137)
I-May-80
DN20 V22(136)
24-Apr-80

The NETWORK output is divided into columns showing:
.the nodename
.the node number (in parentheses)
.system-generated herald, version information, and date.
You can use the NETWORK command before you log in.

3.3

PRINTING OUTPUT

When you type a command on your terminal from a remote station,
the
command travels to the TOPS-10 host where you are logged in, and is
executed on that host.
The response returns automatically to your
remote site terminal. When you use a PRINT or QUEUE command to print
output at your remote station printer, the TOPS-10 monitor queues your
listing for the printer at your remote station.
For example, to print a listing TEXT. MAC
printer, use the following command:

on

your

remote

station

. PRINT TEXT. MAC ~
[Job TEXT Queued, Request-ID 421, Limit 36]

Because you executed the command from a terminal at the remote site,
the print request automatically is queued for the printer at your
remote site.
To see the printer queue, use the PRINT command with no arguments .
.

PRI~

Printer Queue:
Job Name Req#

Limit
User
36
USER[PPN]
On Unit:O /Dest:CTCH22(22)
Started at 16:28:25, printed 0 of 36 pages
There is 1 Job in the Queue (1 in Progress)

~E~

~

3-2

USER PROCEDURES
To print the listing TEXT.MAC at another site, use the
switch in your print command:

/DEST:nodename

.PRINT TEXT.MAC/DEST:KLI026~
[Job TEXT Queued, Request-ID 422, Limit 36]

The job in the print queue looks as follows:
.PRI~

Printer Queue:
Job Name Req#

User
USER[PPN]
On Unit:0/Dest:KLI026(26)
Started at 16:40:15, printed 0 of 36 pages
There is 1 Job in the Queue (1 in Progress)

~E~

~

Limit

~

With a PRINT command, you can use any switches normally associated
with this command as documented
in the TOPS-I0 O~erating System
Commands Manual.
For example,
use the /COPIES sWltch to print
multiple copies of a file, or use the /PRIORITY switch to specify a
nondefault priority for a print request.
{The default priority is 10,
set by your
system administrator;
as a user you can change the
priority of your print requests to any value from 1
(print files
in
the order queued) to 20 (the maximum a user can set).
Higher values
receive service first.
Your remote operator can set higher priorities
or change the allowed range of priorities.)

3.4

SUBMITTING BATCH JOBS

To submit a batch job to be executed on the TOPS-I0 host from your
remote station,
use a SUBMIT command.
You must be logged in on the
host where your batch job is to execute.
For example,
to have the
control
file TSTMAK.CTL execute on your host,
use the following
command:
. SUBMIT TSTMAK ~
[Batch Job TSTMAK Queued, Reguest-ID 804, Limit 0:05:00]

(The default file extension for the SUBMIT command is CTL.)
To see wha.t jobs are in the batch input queue, type SUB
.SUB~

Batch Queue:
Job Name
TSTMAK

Req#

804

Run Time
00:05:00

3-3

User
USER[PPNl

~

USER PROCEDURES
The batch log file associated with your job is
at your remote printer.

automatically

printed

NOTE
Do not use the /PROC switch to the
SUBMIT command;
this switch is used
only to submit a job to an IBM host.
A
job submitted to a host other than the
host where you are logged in appears in
your system's batch input queue and
waits there forever.
With a SUBMIT command, you can use any switches normally associated
with this command.
For example,
use the /DEPENDENCY and /MODIFY
switches to execute files
in a specified order, or
use
the
/OUTPUT:NOLOG switch to suppress printing of your log file.
For more information on the SUBMIT command and the switches you can
use with it,
see the descriptions under SUBMIT and QUEUE in the
TOPS-IO Operating System Commands Manual.

3-4

CHAPTER 4
TROUBLE-SHOOTING

4.1

NORMAL OPERATION

When you start your remote station, CHK11, the hardware verification
program, runs to provide a cursory check of the hardware components.
If CHK11 executes completely and issues no error messages, your
hardware is probably functioning properly, and your station should
operate normally. If CHK11 indicates that your station has some
hardware problems, you can try to restart it once more. If the
problems persist, contact your Field Service representative.
When the remote station is loaded and started for the first time, the
hardware diagnostic program CHK11 runs. This program tries to use
each component of the remote station and issues a message describing
the results.
The following illustrates typical CHK11 output on a
DN200.
INITIALIZING DN200 V17(67) 29-DEC-79 -160000 BYTES OF MEMORY
MF11-UP
KW11-L
1 DL11-A
1 CR11
1 LP11
LP11 #0 NOT RDY
1 DMC11
STARTING DN200 V17(67) 29-DEC-79-The number of bytes of memory is an octal value representing the
number of available bytes in the remote station processor (160000=28K
words; 100000=16K words) .
If there is a hardware failure, CHK11 outputs a message:
ERROR DETECTED AT PC xxx
where xxx is the program counter.

4-1

TROUBLE-SHOOTING
A message preceding the PC address message gives the name of the
device that has failed.
For example,
if your synchronous line
interface
(DMCII)
has failed,
CHKII provides a message of the
following form:

I DMCII
?DMCII #0 (ADR=160540)
ERROR DETECTED AT PC 54522
When such errors occur, contact your Field Service
isolate and correct your hardware problems.

representative

to

For more information on CHRII, see the CHKII Reference Manual.

4.2

WHEN PROBLEMS OCCUR

If the remote station starts, but you do not receive the TOPS-IO
system
prompt,
the TOPS-IO site may not be operating or an
intermediate node may be down.
(An intermediate node is a node
between your remote station and the TOPS-IO host.) If an intermediate
node is down, you must usually wait until it returns to the network.
If there is an alternate path by which you can contact the TOPS-IO
host, the system automatically connects the remote station by that
path.
For information on alternate paths, see Appendix B of this
manual, "NETLDR Command Str ings."
At a remote station, your operator's console can receive a variety of
error messages.
These messages can be issued by the TOPS-IO monitor,
by the programs running at the host site under control of the monitor,
by GALAXY programs such as LPTSPL, and by the programs run at the
remote station (the remote station code and CHKII).
If you are
running OPR, messages from TOPS-IO and from GALAXY are trapped by OPR.
If a program running at the host gets into a nonfunctioning condition
and issues a stopcode,
it presents error messages that contain
information on the crash block and the module that has had a problem.
The message always starts with a message of the following form:
timestamp -- Program xxx
Job xx [PPN] name at Terminal yyy
? Stop code - zzz - in module name
Reason:
explanation
Program is program name
Contents of the ACs

Last stack locations

You may also see messages of the following
problems with GALAXY running at the host:
OPR>
hh:mm:ss
OPR

-- QUASAR is not running

4-2

form

when

there

are

TROUBLE-SHOOTING
A user may see a message of the following form:
%QMRMBR

Send has failed, Message Being Re-sent

If you have problems with the spoolers
contact the TOPS-IO system operator.

or

other

GALAXY

components,

Messages that can appear at your remote station are listed in Table
4-2.
These messages are generated primarily by the remote station
software and the network interface software.
Table 4-2
Station Messages
Message

Meaning

Corrective Action

BREAK POINT
INSTRUCTION
@PC= .••

An unusual
circumstance has
halted the remote
station.
This is
a fatal error.

None. The station
is automatically
reloaded and
restarted.

BUS TRAP @PC= •.•

A failure has
caused the remote
station to halt.
This is a fatal
error.

None. The station
will be automatically
reloaded and
restarted.

Character Not Stored

The buffer in the
remote station is
full, so the
character you just
typed could not be
stored and is lost.

Retype the lost
character.

Connect
sent

An attempt has
been made to
connect to a host.

Wait until you see
the system herald or
log-in prompt.

Connecting to
host system

The remote station
has sent a "connect
initiate" message to
the host but has
not yet received
a "connect confirm."

Wait until
the host
confirms the
connection.

EMT INSTRUCTION
@PC= .•.

An unusual
circumstance has
halted the remote
station. This is a
fatal error.

None. The station
will be automatically
reloaded and
restarted.

FATAL ERROR

The remote station
has halted.

None. The station
will be automatically
reloaded and
restarted.

4-3

TROUBLE-SHOOTING
Table 4-2 (cont.)
Station Messages
Message

Meaning

Corrective Action

hdw has more
sync lines than
software

The assembled
software does not
fit the hardware
at the station.

Contact the system
programmer at the
TOPS-IO site to
reassemble th~
software.
You can
use all the active
synchronous lines
that are recognized
by the software.

Host is available

A host to which you
can connect is
available for
log in.

Log in on the
host.

Host Sent Disconnect

The host your line
is connected to has
timed out waiting for
you to LOGIN or
ATTACH

Type any character to
reestablish the
connection and attach
to the host, or SET
HOST to another host.

Host Went Away

The host you are
using has left the
network.

Either wait until the
host returns to the
network, or type any
character to attempt
to connect to a host.

ILL INSTRUCTION
@PC= ..•

An unusual
circumstance has
halted the remote
station.
This is a
fatal error.

None. The station
will be automatically
reloaded and
restarted.

?INVALID NCL
SUBMSG LENGTH

lTransmission error
between host and
remote station.

Contact the systems
programmer at the
TOPS-IO host site.

lOT INSTRUCTION
@PC= ...

An unusual
circumstance has
halted the remote
station.
This is a
fatal error.

None. The station
will be automatically
reloaded and
restarted.

% LINE PRINTER
OFF-LINE

The line printer
attached to the
remote station
cannot receive or
print data.

Turn on the printer
and press the
ON-LINE switch.
The ON-LINE lamp
should be on. If
trouble persists,
follow the
instructions in
Section 3.1.3,
"Printer."

lAppears only if the remote station software has been assembled
with the DGUTS switch on (see the Networks Software Installation
Guide) .

4-4

TROUBLE-SHOOTING
Table 4-2 (cont.)
Station Messages
Message

Meaning

Corrective Action

Local Input Buffer
Full

The buffer in the
communications front
end or remote
station is full.
If you type more
characters, they
are lost.

Wait until the buffer
has been emptied.

?LOST MSG,
INCONSISTENT
LENGTHS

ITransmission error
between host and
remote station.

Contact the systems
programmer at the
TOPS-IO host site.

MEMORY PARITY
ERROR
MP. REG= •••

A hardware error
has caused the
remote station to
halt.
This is a
fatal error.

Contact your Field
Service
representative.

?MSG LOST, DDCMP
OVERLOAD

ITransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?MSG NOT REQUESTED
LOST

ITransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?MSG WITH ILL TYPE
LOST

ITransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?NCL CAN'T BE
FORWARDED

ITransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?NCL FORMAT BAD,
MSG LOST

lTransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?NCL MSG GEN
FAILED

ITransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

?NODE TRAFFIC
OVERLOAD

lTransmission error
between the TOPS-IO
host and the remote
station.

Contact the systems
programmer at the
TOPS-IO host site.

lAppears only if the remote station software has been assembled
with
the DGUTS switch on (see the Networks Software Installation
Guide) .

4-5

TROUBLE-SHOOTING
Table 4-2 (cont.)
Station Messages
Message

Meaning

Corrective Action

No Host Available

There is no host
in the network which
you can contact.

None. You must
wait until a
suitable host returns
to the network.

??no synchronous
lines??

The software has
been incorrectly
assembled. There
appear to be no
working synchronous
lines; the program
halts.

Contact the systems
programmer at the
TOPS-IO host site or
your Field Service
representative.

?OUT OF SCB
STORAGE

INetwork log jam.

Contact the systems
programmer at the
TOPS-IO host site.

RESTARTING

The station has
been restarted.

None. When the
TOPS-IO system
prompt appears,
you can enter
commands.

?STORAGE ALLOCATION
FAILURE

INetwork problems
are occurring.

Contact the systems
programmer at the
TOPS-IO host site.

TRAP @PC= •••

A failure has caused
the remote station
to halt.

None. The station
will be automatically
reloaded and
restarted.

Path to host
system was lost

Connection between
the remote station
and the TOPS-IO host
has been broken.
Either the TOPS-IO
host or an intermediate node is down.

None. You must
wait until the
host or the
intermediate node
returns to the
network. When the
connection is
reestablished, the
TOPS-IO system prompt
appears with the
message "Please
LOGIN or
ATTACH."

Waiting for Connect
Confirm

Temporary wait
period.

None. Wait until the
station connects.

lAppears only if the remote station software has been assembled
with the DGUTS switch on (see the Networks Software Installation
Guide) .

4-6

APPENDIX A
ROM SWITCHES

A remote station console command must be of the following form:
remote station-console-command

::=#
or #
or 
or nothing

where:
#
::=space

::=<[/Lsyn#] [/Nnnl [/Sser]>
 : :=
or 
The ROM switches that can be used with the remote station are listed
in Table A-l. NETLDR command strings are defined in Appendix B.
NOTE
Always follow ROM switches with a space.

Table A-l
Remote Station ROM Switches
Switch

Function

/Lsyn#

Specifies the synchronous line number
(syn#)
over
which the ROM is to transmit load requests. The
default is o.

/Nnn

Specifies the node number (nn) of the host where the
software for the remote station is stored. The host
at the specified node must also contain NETLDR, which
is used to down-line load the software. The default
is any host;
if either nn or the entire switch is
omitted,
the remote station accepts loads from any
host.

/Sser

Specifies the serial number of
The default is o.

A-l

the

remote

station.

APPENDIX B
. NETLDR COMMAND STRINGS

A command string to be forwarded to NETLDR at the TOPS-10 host can
contain a filespec and/or NETLDR switches. The form of the NETLDR
command stri~g is defined below.
 ::=
or

or


filespec

: :=< [dev:] filename.extl [PPN] >
::=<[/IMAGE] [/LOAD] [/PACKED] [/START:addr]>
::= dev:filename.ext[PPN]

A filespec is optional, but if present, at least filename must appear.
Other filespec arguments default to SYS:, .BIN, and [PPN]=[O,O],
respectively. The third form for NETLDR command strings is valid only
when the string appears in SYS:NETLDR.INI. In this system file, the
first filespec is for the file to contain the dump of the stations,
and the second filespec is for the file to load into the station. For
more information on NETLDR, see the NETLDR specification in the
Software Notebooks.
The optional switches you can send to NETLDR are listed in Table B-1.
Table B-1
NETLDR Bootstrap Switches
Switch

Meaning

/IMAGE

Read the file in image (unpacked) mode.
is the default mode for a PDP~8 node.)

/LOAD

Load the specified file into the remote station;
do not start the program running.

/PACKED

Read the file in packed mode (four 8-bit frames
per KLI0 word).
(This is the default mode for a
PDP-II node.)

/START:addr

Start the program at address addr.
If your
command string does not include a filespec,
NETLDR starts the program currently in memory.
This switch is not needed if filespec appears
and the program is to start at its default start
address.
B-1

(Th is

NETLDR COMMAND STRINGS
B.l

DEFAULT LOAD REQUESTS

If the operator uses no switches or filespecs, the load request that
is sent over the synchronous line is for a PDP-II in packed mode, with
serial number 0, on line O. Loading occurs from line 0 of the remote
station, but the network sees the loading operation from the line on
the adjacent node that performs the loading.
The load request looks for a match with a specification at any TOPS-IO
host in SYS:NETLDR.INI that contains these values. If a match is
found, the command string in NETLDR~INI is used to load the remote
station.
If there is no match, an error message is issued at the
remote station CTY.

B.2

LOADING EXAMPLES

The simplest procedure uses all the available defaults.~,I~~:;·~'::
tl1e.,ope~ato~ turns on the station.
The console;·'t:yp~{s';a·.
'~¥J
return,a:nd line feed ,; The operator presses(R£T)or,w~its):~{<>iF'b<:§'h'~0
~Oh~()le. to . time . out.
The ROM then . send s out et~lQ~dBe9tl~st;,'tc.):"tB~::
aajefcent: node attached to synchronous line 0 ofthe':s:t~~tP'li}~
(geeFigure a-I ). i

NodeALPHA
nn=10

TOPS-l0
Host

NodeGAMMA
nn=60

NodeBETA
nn=11
comm.

.DN200

F.E.

remote
node
"line" 0
of node 60

adjacent node
[NETLDR.INIJ
/NODE:GAMMA/LlNE:5/TYPE:DN200=XPNN:D2C60?/D,SYS:D2C060

Figure B-1

MR-S-008-78

A Default Load Path

At the TOPS-IO site, the file SYS:NETLDR.INI contains an entry of
following form:

the

/NODE:BETA/LINE:5/TYPE:DN200=XPNN:D2C60?/D,SYS:D2C060
This entry causes NETLDR to dump remote station memory up-line into a
file called D2C60?LSD (where ?
is incremented by 1 for each new
dump) on device XPNN: and then to down-line load remote station memory
with the file D2C060.BIN from SYS:.

B-2

NETLDR COMMAND STRINGS
As NETLDR loads the remote station, the following messages
the console at the remote station:

appear

on

%%LOAD REQ ON NODE BETA(ll) LINE:5 FOR DN200 SER:O
FILE:SYS:D2C060
" NODE BETA(ll) LINE 5 DUMPING ONTO XPNN:D2C600.LSD
" NODE BETA{ll) LINE 5 DUMPED FROM 0 THROUGH 157776
" NODE BETA{ll) LINE 5 LOADING FROM SYS:D2C060
" NODE BETA(ll) LINE 5 LOADED
" NODE BETA{ll) LINE 5 STARTING AT ADDRESS 2000
INITIALIZING DN200 V17(67)

21-AUG-78 --

160000 BYTES OF MEMORY
MFII-UP
KWII-L

(CHKll output)
RESTARTING DN200 V17(67)

21-AUG-78

The "RESTARTING ..• " message appears as the software in the remote
station begins to execute.
CHKll output is described in Section 4.1,
"Using CHKll to Check the Hardware."
ROM switches give you flexibility in establishing alternate load
paths.
For example, if your remote station can communicate over more
than one synchronous line, you can send your load request over a
specific line by using the /L ROM switch. Given a configuration of
two hosts as in Figure B-2, and a failure in node BETA, you can load
your node GAMMA from host OMEGA as follows:
.
/Ll/N14

~

B-3

NETLDR COMMAND STRINGS

Node ALPHA

"'C::
[

.

- -r -

PS ,O
Host

Node BETA

Node GAMMA
nn=22

nn,~~m r£ml-- - - Z
F.E.

"Iile,~modems

DN200

----

Node OMEGA
nn=14

rOPS.10
Host
[

"line" 1 _ _--I~
Node ZETA
nn=15

Node DELTA
nn=32
"line" 0

"line" 0

comm.

DN81

F.E.
MR-S-009-78

---

_Figure B-2

Using an Alternate Load Path

This routes the load request through node DELTA.
Node DELTA creates a
station control message for rerouting to the host node OMEGA, adding
its own nodename and the number of the synchronous line leading back
to the requesting DN200.
It then forwards the message to the host at
node OMEGA.
If the network contains more than one host, you can use the
to specify which host is to run NETLDR.

IN

switch

To specify a particular file
to be loaded
from the host,
use a
filespec and any necessary NETLDR switches.
For example, issuing the
following ROM switches and NETLDR command string from node GAMMA
(Figure B-1)
loads node GAMMA with the program SYS:COMM.BIN.
This
program is stored at node ALPHA and
is down-line-loaded by NETLDR.
The switches and command string are:
/NI0 COMM/LOAD

C~

(NETLDR ignores blanks between switches or filespecs.)
To load a file and start the program executing, use:
/NIO SYS :COMM.BIN Gil)

B-4

APPENDIX C
PUNCHED CARD CODES

ASCII data on cards is punched in a specified format.
Punched cards
are 80 columns wide (usually numbered 1 through 80) and 12 rows high
(rows are numbered, top to bottom, as 12, 11, and 0 to 9) (see Figure
C-1) .
All the ASCII characters, including printing characters and
nonprinting control characters, can be represented by the appropriate
punches on a card. In some cases where the punching device does not
have specific keys for punching the code for a particular character,
overpunching or multipunching is used to create the desired punches.
All possible combinations of punches can be achieved by using the
numerics
(which punch rows 0 to 9), the minus (which punches row 11),
and the ampersand (&) (which punches row 12).
(Some keypunch machines
use other symbols to punch in the upper card rows.)
Each character
occupies a single column on the card; up to 5 punched holes may be
required to completely specify ihe code for a character.
character.

0
12
11
0

2

3
4
rows

$

GQ

• • • •
•

5
6
7
8
9

• ••
V
columns 1 to 80

Figure C-1

A

MR-S-014-78

Punched Card

Table C-1 lists the ASCII characters in order by their octal
representation.
Each character is followed by a list of rows that
must be punched in the card to represent the character. For example,
to represent a 1, row 1 of the card must contain a punched hole; to
represent a $, rows 11, 3 and 8, must contain punched holes.
Table
C-2 lists the ASCII characters according to the punched rows required
to represent them.

C-l

PUNCHED CARD CODES
Table C-l
ASCII Character Set
Octal
Value

000
001
002
003
004
005
006
007
010
011
012
013
014
015
016
017
020
021
022
023
024
025
026
027
030
031
032
033
034
035
036
037
040
041
042
043
044
045
046
047
050
051
052
053
054
055
056
057
060
061
062
063
064
065
066
067
070
071
072
073
074
075
076
077

Character

Punches

NUL
SOH
STX
ETX
EaT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
space

12 0 9
12 9 1
12 9 2
12 9 3
9 7
0 9 8
0 9 8
0 9 8
11 9 6
12 9 5
0 9 5
12 9 8
12 9 8
12 9 8
12 9 8
12 9 8
12 11 9
11 9 1
11 9 2
11 9 3
9 8 4
9 8 5
9 2
0 9 6
11 9 8
11 9 8
9 8 7
0 9 7
11 9 8
11 9 8
11 9 8
11 9 8
None
12 8 7
8 7
8 3
11 8 3
0 8 4
12
8 5
12 8 5
11 8 5
11 8 4
12 8 6
0 8 3
11
12 8 3
0 1
0
1
2
3
4
5
6
7

!

"
#
$
%

&
,
(

)

*
+
,
/

0
1
2
3
4
5
6
7
8
9
:

;

<
=

>
?

8
9
8

Octal
Value
8

1

5
6
7

3
4
5
6
7
8

1

1
4
5
6
7

2

11 8 6
12 8 4
8 6
0 8 6
0 8 7

100
101
102
103
104
105
106
107
110
111
112
113
114
115
116
117
120
121
122
123
124
125
126
127
130
131
132
133
134
135
136
137
140
141
142
143
144
145
146
147
150
151
152
153
154
155
156
157
160
161
162
163
164
165
166
167
170
171
172
173
174
175
176
177

Character

Punches

@

8

A
B
C
D
E
F
G
H

12
12
12
12
12
12
12
12
12
11
11
11
11
11
11
11
11
11
0
0
0
0
0
0
0
0
12
0
11
11
0

I

J
K
L
M
N
a
P

Q
R
S
T

U
V
W

X
Y
Z
r
\

1
-

8
a
b

c
d
e
f
g
h
i
j

k
I
m

n
0

P
q
r

s
t
u

v
w
x
y

z
{

I
}

DEL

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
11
11
11
11
11
11
11
11
12
12
11
11
12

4
1
2
3
4
5
6
7
8
9

1
2
3
4
5
6
7
8
9

2
3
4
5
6
7
8
9
8
8
8
8
8

1
0
0
0
0
0
0
0
0
0
11
11
11
11
11
11
11
11
11
0
0
0
0
0
0
0
0
0
11
0
0
9

2
2
2
7
5
1
2
3
4
5
6
7
8
9

1
2
3
4
5
6
7
8
9

2
3
4
5
6
7
8
9

1
7

MR-S-2285-82

C-2

PUNCHED CARD CODES
Table C-2
ASCII Characters by Punched Rows
Punches

Character

Punches

None
12
11

space

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11

&

-

0

0

1
2

1
2

3

3

4

4

5
6
7
8
9

5
6

7
8
9

12
12
12
12
12
12
12
12
12
12
12
11
11
11
11
11
11
11
11
11
11

11

I

0

{

1
2

A
B
C
D
E
F
G
H
I

7
8
9

P

0
0
0
0
0
0
0
0
0
9
9
8
8
8
8
8
8
8

1
2
3
4

/

12
12
12
12
12
12
12
12
12
12
12
12

3

4
5
6

7
8
9
0

}

1
2

J

K
L
M
N
a

3

4
5
6

Q
R

5

S
T
U
V

6

W

7

X
Y

8
9

Z

2

SYN
EaT

.

7

1
2

:

3

#

4

,

@

5
6
7

11
11
11
11
11
11
11
11
11
0
0
0

=

"
1
2

j
k

3

1

4

m

5

n

6

0

7
8
9

q
r

1
2

b

3

c

p
a

0
0
0
0
0
0
0
0
0
9
9
9

0
0
0
0
0
0
9
9
9
9
9
8
8
8
8
8
8
0
0
0
0
0
0
0
0
0
9
9
9
9
9
8
8
8
8
8
8
9
9
9
8
8
8
8
8
8
8
8
8
9
9
9
9
9
9
9
9
9
9
9
9
9

Character

4

d

5

e

6

f

7

g

8
9

h
i

1
2

SOH
STX
ETX
HT
DEL
I

3

5
7

2
3

4

<

5

(

6

+

7

!

-

1
2

s

3

t

4

u
v
w
x
y

5
6

7
8

6
8

z
DC1
DC2
DC3
BS
CAN

2

1

3

$

9

1
2

3

4

*

5

)

6

;

7

7

LF
ETB
ESC

2

\

5
6

3

,

4

%

5

-

6

>

7

?

4

DC4
NAK
SUB
VT
FF
CR
SO
SI
EM
FS
GS
RS
US
ENQ
ACK
BEL
DLE
NUL

5
7
12
8
12
8
12
8
12
8
12
8
11
8
8
11
11
8
11
8
11
8
0
8
8
0
0
8
12 11 9
12 0 9

3

4
5
6

7

1
4
5
6
7
5
6
7
8
8

1
1

MR-S-2286-82

C-3

APPENDIX D
GLOSSARY

This glossary contains terms that are used in this document.
Term

Meaning

assemble

To take a program written in the assembly
language of a computer and prepare a program
in the machine language of that computer.
(For example, to take a MACRO program and
create a binary program from it.)

asynchronous line

A line (cable) over
which
asynchronous
communications occur.
Such lines are often
used to connect terminals to a processor.
Asynchronous
transmission
is
data
transmission in which time intervals between
transmitted characters need not be of equal
length.
Asynchronous
transmission
is
typically done at moderate rates of speed.

binary file

A file stored on a computer in
entries are in a binary format.

bootstrap

A routine that initiates the reading of
another routine and whose first instructions
bring
in
the
rest
of
the
routine.
Bootstrapping makes it possible for a tiny
routine (one stored, for example, in
a
bootstrap ROM) to initiate the automatic
loading of a larger routine.

down-line load

To load a program from a host processor over
a line to a remote processor. The direction
of transmission is away from the host.

host

A complete computer facility with a central
processor, mass storage devices (such as
disks), peripherals (such as printers), and a
monitor command routine (MCR) or command
decoder. The MCR is part of the TOPS-IO
operating system.

load request

The message sent by the remote station ROM to
a host. It asks the host to load the remote
station and can specify the route for loading
over the network.

D-1

which

all

GLOSSARY
Term

Meaning

modem

A device that modulates and
demodulates
signals
transmitted
over
communications
circuits. Some modems are also called data
sets.

node

A processor in the TOPS-IO network.
Every
processor in the network is a node, whether
it is a remote station, a communications
front end, or a host itself.

remote station

Equipment that communicates with a host, but
that is distant from it. A remote station
normally has at least a card reader and a
printer;
it
can also have interactive
terminals.

ROM

Read-Only Memory, a memory that can be read
but never written into.
The ROM in the
remote station contains a bootstrap program
that brings in another program from the host.
The program from the host runs the remote
station.

synchronous line

A line (cable)
over
which
synchronous
communications occur. Such lines are used to
connect processors. Synchronous transmission
is data transmission in which time intervals
between transmitted characters are of equal
length.
Synchronous
transmission
is
typically done at relatively high speeds.

TOPS-IO

The total operating system. TOPS-IO
all hardware and software resources.

up-line dump

To send a core-image
location to a host.

D-2

dump

from

manages
a

remote

APPENDIX E
REMOTE STATION OPR COMMANDS

This appendix contains all OPR commands that you can use as the remote
operator at a remote station if your PPN has the appropriate
privileges. The system administrator at the host must use REACT to
give the PPN where you log in remote operator privileges.
aPR provides a help facility with command recognition
(use of the
~
key)
and command help (use of the question mark (?)). You use
aPR commands to control the printer and card reader at your remote
station,
to direct OPR output, to obtain information, to communicate
in the network, and to control jobs. You should cooperate with the
system operator at the host where you log in as remote station
operator to set up the system files
(such as SYS:SYSTEM.CMD and
SYS:LPFORM.INI)
for optimum use of your remote station. The system
operator can also place commands you can issue from your remote
station in SYSTEM.CMD for execution when the host system is brought
up.
and explained
The OPR commands are listed by function in Table E-l,
briefly in Tables E-2 and E-3.
Each OPR command is more fully
explained in the remainder of this appendix.
Table E-l
OPR Command Functions
Use
To use with your
printer

Command
ABORT
ALIGN
BACKSPACE
CANCEL
CONTINUE
FORWARDSPACE
HOLD
NEXT
RELEASE
REQUEUE
SET PRINTER
SHUTDOWN
START
STOP
SUPPRESS

E-l

Inverse

FORWARDSPACE
STOP
BACKSPACE
RELEASE
HOLD
START
SHUTDOWN
CONTINUE

REMOTE STATION OPR COMMANDS
'rable E-1 (cont.)
OPR Command Function
~.

Use
To use wi th
your card reader

Command
ABORT
CONTINUE
HOLD
RELEASE
NEXT
SHUTDOWN
START
STOP

STOP
RELEASE
HOLD
START
SHUTDOWN
CONTINUE

To direct OPR
output

DISABLE OUTPUT-MESSAGES
ENABLE OUTPUT-MESSAGES
SET TERMINAL

To obtain
information

HELP"l

SHOW

Inverse

ALLOCATION
CONTROL FILE
MESSAGESl
OPERATORSl
PARAMETERSl
QUEUESl
ROUTE-TABLEl
STATUSl
SYSTEM-LISTS
TIME

To communicate in
the network

REPORT
RESPOND
SEND

To control jobs

MODIFY JOBS
TAKE

To exit from OPR

EXIT

The objects shown below indicate the device or queue on which a
given OPR command operates.
These objects can be specified in
some of the commands described in subsequent sections.

If you SET TERMINAL KEYPAD on a VT52, this
you press one key.

E-2

command

executes

when

REMOTE STATION OPR COMMANDS
Table E-2
aPR Objects
Object

Meaning

BATCH-STREAM

Batch input stream, controlled by BATCON.

PRINTER

Line printer spooler,
output spooler.

controlled

by

the

READER

Card reader spooler,
input spooler.

controlled

by

the

ALL-JOBS

All jobs waiting or held in all
the system.

BATCH-JOBS

All jobs or a specified job waiting in the
batch input queue;
the queue is the list
of jobs waiting
to be processed by the
GALAXY batch system.

PRINTER-JOBS

All jobs or a specified job waiting in
printer output queue.

the

READER-JOBS

All jobs or a specified job waiting in
card reader input queue.

the

From remote stations, you cannot execute action commands
the following aPR objects:

queues

in

containing

BATCH-STREAM
CARD-PUNCH
PAPER-TAPE-PUNCH
PLOTTER
If you issue an aPR action command with one of
aPR sends you an error message, for example,

the

above

objects,

Batch commands not allowed from remote nodes -or
System operator privilege required -You can get help on all commands and aPR parses all commands,
but
aPR
will
not execute commands that require system operator
privileges.

E-3

REMOTE STATION OPR COMMANDS
Table E-3
OPR Commands
Command

Function

Restrictions

ABORT

Terminates a currently
running job.

Only aborts jobs
queued for your
remote site
devices.

ALIGN

Prints an alignment
file to allow you to
align forms.

Only prints on the
printer at your
remote site.

BACKSPACE

Backspaces a print
queued to the line
to allow repeating
printing of a job,
or page (s) .

Only backspaces a
file on the printer
at your remote
si te.

CANCEL

Cancels a job or jobs
in a queue.

Only cancels jobs
initiated at your
remote site and
queued for your
remote site
devices.

CONTINUE

Restarts a device
temporarily stopped by
the STOP command.

Only continues
your remote
site devices.

DISABLE

Stops the output
of various types of
messages.

Only disables
messages with
your remote site
as destination.

ENABLE

Allows the output display
of various types of
messages.

Only enables
messages with
your remote site
as destination.

EXIT

Exits from OPR.

Only exits from'the
OPR you are running
from the remote
site.

FORWARDSPACE

Spaces a print file
forward on the line printer
to allow you to skip the
printing of a job, file,
or page(s).

Only forward spaces
for a file
printing on the
printer at your
remote site.

HELP

Displays information
about OPR commands.

Does not
•
distinguish between
information
applicable at
the host and
at the remote
site.

E-4

file
printer
the
file,

REMOTE STATION OPR COMMANDS
Table E-3 (cont.)
OPR Commands
Command

Function

Restrictions

HOLD

Stops scheduling jobs
for a given device.

Only holds devices
for your remote
site devices.

MODIFY

Changes the priority of
a job request.

Only modifies
jobs initiated
at your remote
site and for your
remote site
devices.

NEXT

Changes the sequence of
a job request

Only affects jobs
initiated at your
remote site

RELEASE

Starts scheduling
jobs held in a
GALAXY queue with
a HOLD command.

Only starts jobs
initiated at your
remote site and for
your remote site
devices.

REPORT

Places a comment in the
system error file
ERROR.SYS.

None.

REQUEUE

Terminates a job queued
to an I/O device and
reschedules it for
processing later.

Only reschedules
jobs initiated at
your remote site
and your remote
site devices.

RESPOND

Answers a message that
has been sent to you.

Gives one-line
response to
messages sent
to you.

SEND

Sends text messages.

Sends one-line
message only.

SET

Sets parameters for
OPR objects.

Only sets
parameters for
printers and
terminals at your
remote site.

SHOW

Displays system
information.

Mostly displays
information that
pertains to your
remote site.

SHUTDOWN

Terminates scheduling
for devices.

Only terminates
scheduling for
devices at your
remote site.

E-5

REMOTE STATION OPR COMMANDS
Table E-3 (cont.)
OPR Commands
Command

Function

Restrictions

---.----------------;----,-----------------------------+-----------------------~

START

Starts scheduling for
devices.

Only starts devices
at your remote
site.

STOP

Temporarily stops devices.

Only stops devices
at your remote
site.

SUPPRESS

Suppresses blank lines
on the printer.

Only suppresses
printer at your
remote site, and
only one file or
job.

TAKE

Takes OPR commands
from a previously made
file.
.

The file can
contain only OPR
commands valid
for your remote
station.

E-6

REMOTE STATION OPR COMMANDS
ABORT:

ABORTING JOBS

The ABORT command terminates a currently running job.
At the
station, you can only abort jobs queued for your own devices.

remote

Format:
ABORT

PRINTER}
{ READER n

]
/PURGE
.
/REASON:comment
[ /REQUEST-ID:nnnn

Where:
PRINTER

The printer at your remote station.

READER

The card reader at your remote station.

n

o for remote station card readers, 0 for
remote station printers.

/PURGE

Remove the job from the system.
Also
aborts all output from the job.
For a
printer job, no header and/or trailer
pages are kept.Al

/REASON:comment

Record a comment indicating why you
aborted the job.
When you abort a
printer job, this command appears in the
user's
log file or on the printed
output.
The comment cannot exceed a
single line.

You cannot use the following keywords and
with remote operator privileges:

switches

to

this

command

BATCH-STREAM
CARD-PUNCH
/NODE
PAPER-TAPE-PUNCH
PLOTTER
Example:
OPR>ABORT READER 0 ~
aPR>
09:34:45
Reader 0 [DN200 (20)]
aPR>

E-7

-- Aborting --

REMOTE STATION OPR COMMANDS
ALIGN:

ALIGNING PRINTER PAPER

The ALIGN command halts the line printer and allows you to print a
file
to align forms
in the printer.
You can only use this command
when a job is active.
Use this command when you must align special
forms such as payroll checks or invoices.
Format:
ALIGN PRINTER n

[~~!0~~~~~nFilespec]
/REPEAT-COUNT:nnnn
/STOP

Where:
PRINTER

The printer at your remote station.

n

o

Alignment
Filespec

Name of file
(name and type)
used to
align the forms.
The default
file
specification is SYS:forms.ALP, where
"forms" contains the form name
(for
example, SYS:NARROW.ALP).

/PAUSE:nnn

Time in seconds (nnn) for the printer to
wait before reprinting the alignment
file.
Default:
10 seconds.

/REPEAT-COUNT:nnnn

Number of times to print the file.
Default:
25

/STOP

Switch to resume normal printing or stop
aligning forms on the line printer.

You cannot use the following
operator privileges:

for remote station printers.

switch

for

this

command

with

remote

/NODE
Example:
OPR>ALIGN PRINTER 0 /PAUSE:30 Ci~J
OPR>
10:34:03
Printer 0 [DN200 (20)]
OPR>

E-8

-- Alignment Scheduled --

REMOTE STATION OPR COMMANDS
BACKSPACE:

BACKSPACING WITHIN A JOB

The BACKSPACE command backspaces a print request destined for your
printer to allow you to repeat the printing of a job, file, or page(s)
of a file.
For example, if forms become jammed in~the printer,
this
command enables you to backspace the print file to repeat the damaged
pages.
Format:
/COPIEs:nn}
/FILE
{ /PAGES:nnn

BACKSPACE PRINTER n
Where:
PRINTER

The printer at your remote station.

n

o

/COPIES:n

Number of additional copies to be printed;
this number is added to the number previously
queued with the PRINT command.

/FILE

Switch to indicate that one file
backspaced and printed again.

/PAGES:nnn

Number of pages to backspace a file currently
being printed.

If you do not specify
/PAGES.

for remote station printers.

either

You cannot use the following
operator privileges:

/COPIES
switch

or
for

/FILE,
this

you

command

is

must
with

to

be

specify
remote

/NODE
Example:
OPR)BACKSPACE PRINTER 0 /PAGES:12 ~
OPR)
10:23:50
Printer 0 [DN200 (20)]
OPR)

E-9

-- Backspaced 12 Pages --

REMOTE STATION OPR COMMANDS
CANCEL:

CANCELING REQUESTS

The CANCEL command cancels job requests for jobs currently processing
or waiting
to be processed.
If an active request is canceled, that
request is aborted automatically. At the
remote station,
you can
cancel
requests
that are to be sent to your printer, and you can
cancel requests in the batch input queue that were initiated at the
remote station.
Format:
CANCEL

fBATCH-REQUEST }
\ PRINTER-REQUEST

Where:
BATCH-REQUEST

Request in the batch input queue.

PRINTER-REQUEST

Request in the printer queue.

nnnn

Request number assigned by the system.
Use
request number
to cancel an active job or a
request in the queue.

[PPN]

Project-programmer number that identifies the
user whose jobs are to be canceled.

*

All requests in the given queue.

You cannot use the following keywords
operator privileges:

to

this

command

CARD-PUNCH-REQUEST
MOUNT-REQUEST
PAPER-TAPE-PUNCH-REQUEST
PLOTTER-REQUEST
Example ::
OPR>CANCEL BATCH-REQUEST
OPR>
12~05:41

*

~

-- 10 Jobs Canceled --

OPR>

E-IO

with

remote

REMOTE STATION OPR COMMANDS
CONTINUE:

RESTARTING A STOPPED DEVICE

The CONTINUE command continues processing on a device temporarily
stopped by the STOP command.
At the remote station, you can continue
processing only for your own devices.
Format:
CONTINUE

PRINTER)
{ READER n

Where:
PRINTER

The printer at your remote station.

READER

The card reader at your remote station.

n

o for remote station card readers, 0 for remote station
printers;
or x:y, a range of devices.

You cannot use the following keywords,
switches,
this command with remote operator privileges:

and

parameters

BATCH-STREAM
CARD-PUNCH
PAPER-TAPE-PUNCH
PLOTTER
/NODE
Example:
OPR>CONTINUE PRINTER 0 ~
OPR>
11:40:23
Printer 0 [DN200 (20)]
OPR>

E-11

Continued

to

REMOTE STATION OPR COMMANDS
DISABLE:

STOPPING MESSAGE DISPLAYS

The DISABLE command allows you to control the messages that you
receive.
You can disable the display of messages for any of your
devices, or you can disable messages by message type
(for example,
JOB-MESSAGES) •
A simple way to select only certain messages is to
DISABLE OUTPUT-DISPLAY of ALL-MESSAGES and then ENABLE OUTPUT-DISPLAY
of only those you wi sh to see.
(See the ENABLE command to OPR.)
Note that with remote operator privileges you can DISABLE or ENABLE
only message output;
you are not able to restrict or permit other
system activities.
Format:

DISABLE OUTPUT-DISPLAY

ALL-MESSAGES
BATCH-MESSAGES
CARD-PUNCH-MESSAGES
CARD-READER-INTERPRETER-MESSAGES
MOUNT-MESSAGES
PAPER-TAPE-PUNCH-MESSAGES
PLOTTER-MESSAGES
PRINTER-MESSAGES
READER-MESSAGES
USER-MESSAGES

/INFORMATION-MESSAGESJ
/JOB-MESSAGES
[ /OPR-ACTION-MESSAGES

Where:
ALL-MESSAGES

Disables all messages sent to this aPR.

BATCH-MESSAGES

Disables messages about batch jobs.

CARD-PUNCH-MESSAGES

Disables messages about card punch
at the host.

CARD-READER-INTERPRETER-MESSAGES
Disables messages about the card
interpreter.
MOUNT-MESSAGES

Disables all messages
structures and tapes.

about

jobs

reader
mounting

PAPER-TAPE-PUNCH-MESSAGES
Disables messages about the
punch.

paper

PLOTTER-MESSAGES

Disables messages about the
the host.

plotter

PRINTER-MESSAGES

Disables messages about printer jobs.

E-12

tape
at

REMOTE STATION OPR COMMANDS
messages

about

card

reader

READER-MESSAGES

Disables
jobs.

USER-MESSAGES

Disables user messages.

/INFORMATION-MESSAGES

Disables informational messages for
specified device or message type.

the

/JOB-MESSAGES

Disables messages about jobs for
specified device or message type.

the

/OPR-ACTION-MESSAGES

Disables messages for which operator
action
is needed for the specified
device or message type.

Example:
OPR) DISABLE OUTPUT-DISPLAY USER-MESSAGES /JOB-MESSAGES
OPR)

E-13

~

REMOTE STATION OPR COMMANDS
ENABLE:

STARTING MESSAGE DISPLAYS

The ENABLE command allows you to control
your OPR terminal.

the

messages

displayed

at

Note that with remote operator privileges you can DISABLE or ENABLE
only message output;
you are not able to restrict or permit other
system activities.
Format:

ENABLE OUTPUT-DISPLAY

ALL-MESSAGES
BATCH-MESSAGES
CARD-PUNCH-MESSAGES
CARD-READER-INTERPRETER-MESSAGES
MOUNT-MESSAGES
PAPER-TAPE-PUNCH-MESSAGES
PLOTTER-MESSAGES
PRINTER-MESSAGES
READER-MESSAGES
USER-MESSAGES

/INFORMATION-MESSAGES]
/JOB-MESSAGES
[ /OPR-ACTION-MESSAGES

Where:
ALL-MESSAGES

Enables the display of all messages
the OPR you are running.

BATCH-MESSAGES

Enables the display
batch jobs.

messages

about

CARD-PUNCH-MESSAGES

Enables the display of messages
the card punch at the host.

about

of

for

CARD-READER-INTERPRETER-MESSAGES
Enables the display of messages about
interpreter.
Such
the
card
reader
messages occur when cards are in the
wrong
format
or
contain
illegal
commands.
MOUNT-MESSAGES

Enables the display of messages
mounting tapes and disks.

E-14

about

REMOTE STATION OPR COMMANDS
PAPER-TAPE-PUNCH-MESSAGES
Enables the display of messages
the paper tape punch at the host.

about

PLOTTER-MESSAGES

Enables the display of messages
the plotter at the host.

about

PRINTER-MESSAGES

Enables the display
printer jobs.

of

messages

about

READER-MESSAGES

Enables the display
card reader jobs.

of

messages

about

USER-MESSAGES

Enables the display of user messages.

/INFORMATION-MESSAGES

Enables the display of informational
messages about a specified device or
type of message.

/JOB-MESSAGES

Enables the display of messages about
jobs destined for a specified device or
type of message.

/OPR-ACTION-MESSAGES

Enables the display of messages that
require operator action
(for example,
please or forms-change requests).

Example:
OPR) ENABLE OUTPUT-DISPLAY PRINTER-MESSAGES /JOB-MESSAGES
OPR)

E-15

C~I)

REMOTE STATION aPR COMMANDS
EXIT:

LEAVING aPR

The EXIT command removes you from OPR command level and returns you to
TOPS-IO monitor level.
When you exit from aPR, any messages intended for your remote station
are routed to the operator at the TOPS-IO host. It is good practice
to have the operator's console at your remote station dedicated to
running aPR and not to exit from aPR while your station is running.
Format:
EXIT
Example:
OPR)EXIT

~

E-16

REMOTE STATION OPR COMMANDS
FORWARDSPACE:

SKIPPING PRINT FILES

The FORWARDSPACE command skips forward in a file destined for
the
printer
to omit printing an entire job, a file, or a specified number
of pages.
If you require only a portion of some printed output,
this
command lets you save paper and print only the output you need.
Format:
FORWARDSPACE PRINTER n

/COPIEs:nnnn}
/FILE
{ /PAGES:nnn

Where:
PRINTER

The printer at your remote station.

n

o for remote station printers.

/COPIES:nnnn

Skip the indicated number of copies;
this
number
is subtracted from the number of
copies queued with the PRINT command.

/FILE

Skip one file.

/PAGES:nnnn

Skip the indicated number of
file currently being printed.

You must specify either
FORWARDSPACE command.

/COPIES,

/FILE,

or

pages

/PAGES

You cannot use the /NODE switch to this command with
privileges.

remote

in

with

OPR> FORWARDSPACE PRINTER 0 /COPIES: 15 @)
OPR>
13:21:09
Printer 0 [DN200(20)]
-- Forward Spaced 15 Copies --

E-17

the

operator

Example:

OPR>

the

REMOTE STATION OPR COMMANDS
HELP:

OBTAINING INFORMATION

The HELP command displays information about any of the OPR commands on
your terminal.
If you type HELP, OPR displays a list of available OPR
commands.
To obtain information about a specific OPR command,
type
HELP and the command name.
For information about all OPR commands,
type HELP *
You can obtain HELP information on all OPR commands from
your
remote station,
not just on commands useful at the remote
station.
HELP is also available through the question mark
(?)
and
~
key.
The question mark prompts you to fill in your command line
properly;
the
~
key fills
in what it can,
and
provides
guidewords.
Format:
HELP
Where:
command

Any OPR command name.

Examples:
OPR>HELP RESPOND C~l_IJ
OPR>
The RESPOND command allows you to reply
that requires a response.

to

any

message

The format is:
RESPOND  response
where  is an outstanding message number
followed by a single or multiple line response.
OPR>

E-18

REMOTE STATION OPR COMMANDS
HOLD:

HOLDING JOBS IN A QUEUE

The HOLD command stops scheduling jobs that are waiting
in a GALAXY
queue.
After you issue a HOLD command, jobs can be submitted, but
they are not scheduled for processing until you issue a RELEASE
command.
If a job has already been processed, it cannot be held.
At the remote station, you can only use the HOLD command to hold batch
jobs submitted from your station and printer jobs destined for your
remote s ta t io"n.
Format:
HOLD

BATCH-JOBS }
{ PRINTER-JOBS

nnnn }
{ lPPN]

Where:
BATCH-JOBS

Jobs in the batch input queue.

PRINTER-JOBS

Jobs in the print queue.

nnnn

Request number assigned by the system.

[PPN]

Project-programmer number
user.

*

All job requests in the specified queue.

th~t

identifies the

You cannot use the following keywords and switch to this command
remote operator privileges:
CARD-PUNCH-JOBS
PAPER-TAPE-PUNCH-JOBS
PLOTTER-JOBS

INODE
Example:
aPR) HOLD PRINTER-JOBS * ~
OPR)
13:19:04
-- 10 Jobs Held
OPR)

E-19

with

REMOTE STATION OPR COMMANDS
MODIFY:

MODIFYING REQUESTS

The MODIFY command allows you to change the priority of a batch job or
printer request.
Higher priority numbers are processed first.
At the
remote station, you can change only the priority of jobs queued
for
your
line printer and the priority of jobs in the batch input queue
initiated at your remote station.
Format:
MODIFY

BATCH-REQUEST }
{ PRINTER-REQUEST

nnnn }
{ lPPN]

PRIORITY nn

Where:
BATCH-REQUEST

A request in the batch input queue.

PRINTER-REQUEST

A request in the print queue.

nnnn

Request number assigned by the system.

[PPN]

Project-programmer number that identifies the
user.

*

All job requests held in the queue
station.

PRIORITY nn

The priority (nn) you assign to the request.

for

your

When a user makes a print request
(issues a PRINT command),
the
request receives the system default priority
(nn),
normally 10,
specified by the system administrator at the host.
As the remote
station operator, you can use
the MODIFY command to change the
priority of a print request.
The system recognizes priorities in the range 1 to 63,
with higher
numbers receIvIng service first.
A job with a priority outside the
allowed range is queued but not serviced (printed or executed).
You
can change the
range of priorities for
the printer with the SET
PRINTER PRIORITY-LIMITS command, and you can change the priority of a
specific
job with the OPR MODIFY command.
Users can change the
priorities of their own jobs with the /PRIORITY switch to the PRINT or
SUBMIT command.
A user can specify priority only as high as 20;
you
can use priority 1 to print files in the order you queue them,
rather
than smallest first.
For batch jobs, priority 1 has the same effect,
but may delay the running of the job until the queue is empty of all
other
jobs.
For batch jobs, it is preferable to use the /DEPENDENCY
switch with the /MODIFY and SUBMIT commands to have batch jobs run in
a specific order.

E-20

REMOTE STATION OPR COMMANDS
You cannot use the following keywords and switch to this command
remote operator privileges:

ACTIVE-SWAPPING-LIST
CARD-PUNCH-REQUEST
CRASH-DUMP-LIST
/NODE
PAPER-TAPE-PUNCH-REQUEST
PLOTTER-REQUEST
SYSTEM-SEARCH-LIST
Example:

OPR>MODIFY PRINTER-REQUEST [27,5117] PRIORITY 5
OPR>
14:01:29
-- 10 Requests Modified -OPR>

E-21

~

with

REMOTE STATION OPR COMMANDS
NEXT:

SPECIFYING THE NEXT JOB IN THE QUEUE

The NEXT command allows you to move one job ahead of the rest in the
queue.
Using the NEXT command does not alter the priority or sequence
of other jobs in the queue.
If another job is currently printing, the
request you specify starts as soon as the current request is printed.
FOHMAT:
NEXT PRINTER 0 HEQUEST-ID nnnn
Where:
nnnn

is the request-identification number

The following
privileges:

keywords

are

not

available

with

remote

operator

BATCH-STREAM
CARD-PUNCH
PAPER-TAPE-PUNCH
PLOTTER
Example:
A user (SEN) requests that her print job be moved to the top of the
print queue to be printed when a printer is available.
You must
examine the print queue to obtain the request-identification number
for her print request.
Then you use the NEXT command to place her
request next in the queue.
OPR> SHOW QUEUES PH INTER G"ED
aPR>
11:35:43

-- System Queues Listing

Printer Queue:
Job Ndme

*

Req

Limi t

User

BREAK
14
200
KOVALCIN, 0 [10,46351
Stdrteo dt 11:30:44, printed 20 of 200 pages
MAIL
145
35
MAROTTA, M [27,55551
SNOOPY
10
65
SEN, M
[443,25201
Tpere dre 3 jobs in the queue (1 in progress)

/After:29-MAY-82 12:00

OD

C~)

I .
aPR> NEXT (J ob
aPR>
11:36:17

,

On Unit:O

on)

PRINTER (unit number)

o HEQUEST-IO 10

Printer 0 -- NEXT request 10 scheduled --

OPP>

E-22

~

REMOTE STATION OPR COMMANDS
RELEASE:

RELEASING JOBS IN THE QUEUE

The RELEASE command restarts the scheduling of jobs for your station.
Any jobs held with the HOLD command are scheduled for processing after
you issue the RELEASE command.
At the remote station, you can use the RELEASE command to release only
print jobs queued
for your station and
jobs in the batch queu~
initiated from your station.
Format:
RELEASE

{

BATCH-JOBS }
PRINTER-JOBS

nnnn }
{ lPPN]

Where:
BATCH-JOBS

Jobs in the batch input queue.

PRINTER-JOBS

Jobs in the print queue.

nnnn

Request number assigned by the system.

[PPN]

Project-programmer number that identifies the
user.

*

All job requests held in the queue.

You cannot use the following keywords
operator privileges:

to

CARD-PUNCH-JOBS
/NODE
PAPER-TAPE-PUNCH-JOBS
PLOTTER JOBS
Example:
OPR>RELEASE BATCH-JOBS * ~
aPR>
14:23:45
-- 2 Jobs Released
aPR>

E-23

this

command

with

remote

REMOTE STATION OPR COMMANDS
REPORT:

RECORDING COMMENTS

The REPORT command allows you to report existing conditions in the
system log file named ERROR.SYS.
REPORT is useful when you do not
wish to specify a reason with the /REASON switch to an ABORT or
REQUEUE command.
When you issue a REPORT command, your message is placed in
log file [3,3]OPERAT.LOG and in ERROR.SYS.

the

ORION

You can enter a single- or multiple-line messag€.
To enter a single
line comment, enter the text and terminate it with ~ . To enter a
multiline comment, press ~ before entering your text,
then enter
the text and terminate your message with
~TRL/~·.
Format:
REPORT [user Name]

[device]

[text]

Where:
User Name

User name
report.

Device

The device that is the subject of this report.
(Omit the device name if the report does not
concern a device.)

Text

A comment describing the condition to be logged.

to

identify

the

person

making

the

Examples:
OPR>REPORT OP170 CDR170:
too many pick checks ~
aPR>
hh:mm:ss -- ERROR.SYS entry made by the REPORT Command
OPR>REPORT (by) OP170 PTR? confirm for multiple line response
or single line response
OPR>REPORT OP170 PTRC~
Enter Text and Terminate with ~Z
The printer at this station is giving a lot of print hammer
dlarms.
F.S.
has been called.
~
~~

OPR>
hh:mm:ss

ERROR.SYS entry made by the REPORT Command --

The SYSERR entry has the following form:
sequence-number.
PRT on TTY # XXX
MESSAGE:

hh:mm:ss

SYSTEM LOG ENTRY BY OP170 FOR

(text of message)

E-24

DEVICE

REMOTE STATION OPR COMMANDS
REQUEUE:

RESCHEDULING JOBS

The REQUEUE command terminates a job currently in the printer queue
and
reschedules it for processing at a later time.
The requeued job
is held and its current processing terminates.
To reschedule the job,
issue a RELEASE command.
At the remote station, you can only requeue jobs queued for
printer.

your

own

Format:
/REQUEST-ID:nnnn
REQUEUE PRINTER n

]

BEGINNING-OF{~~~~}

[ CURRENT-POSITION
/REASON:comment
Where:
PRINTER

The printer at your remote station.

n

o for remote station printers.

/REQUEST-ID:nnnn

Request number assigned by the system.

BEGINNING-OF COPY

Requeue from the beginning of the copy
originally queued with a /COPIES switch.
(Also see the BACKSPACE and FORWARDSPACE
commands) .

BEGINNING-OF FILE

Requeue from
current file.

BEGINNING-OF JOB

Requeue from the beginning
of
the
current job.
With the JOB parameter,
the entire job is requeued.

CURRENT-POSITION

Requeue from the current position of the
current job on your printer.

/REASON:comment

Record a comment indicating why you
requeued
the
job.
The comment 1S
recorded
in
the
OPR
log
file
[3,3]OPERAT.LOG.

the

beginning

of

You cannot use the following keywords and switch to this command
remote operator privileges:
BATCH-STREAM
CARD-PUNCH
PAPER-TAPE-PUNCH
PLOTTER
/NODE
Example:
OPR)REQUEUE PRINTER 0 BEGINNING-OF JOB
OPR)
15:51:06
Printer 0 [DN200(20)]
OPR)

E-25

~

Requeued --

the

with

REMOTE STATION OPR COMMANDS
RESPOND:

ANSWERING MESSAGES

The RESPOND command allows you to answer a message sent from a user
waiting for a response. When a user sends a message that requires a
response, OPR assigns a number to the message so that you can keep
track of it.
Your response can be a single line or multiple lines.
View outstanding messages with the SHOW MESSAGES command.
With remote operator privileges, you can respond only to messages that
have been sent to your station.
Format:
RESPOND nnn Text
Where:
nnn

Outstanding message number.

Text

Response to the outstanding message.

Examples:
OPR>SHOW MESSAGES ~)
hh:mm:ss
-- System Messages Outstanding -<2>

Printer 0 [DN200(20)]
Please Load Forms Type 'NARROW'
Type 'RESPOND  CONTINUE' WHEN READY

OPR> RESPOND 2 CONTINUE ~
Printer 0 [DN200(20)] -- LOADING VFU WITH 'NARROW' -OPR> RESPOND 2
multiple
line
response
OPR>

~Q

C SEND OPERATOR please send the new stand-alone schedule
OPR>
14:22:50
--SEND Command Completed--

~

OPR>
At the central site, the operator's terminal
following message is displayed:

buzzer

sounds

aPR>
hh:mm:ss From Operator DN200(20):
=> please send the new stand-alone schedule
aPR>

E-27

and

the

REMOTE STATION OPR COMMANDS
SET PRINTER:

SETTING PRINTER CHARACTERISTICS

The SET PRINTER command sets characteristics for the printer at your
remote station. You can specify the name of a FORMS-TYPE, the action
to take when a job exceeds the output line limit that you specify, the
PAGE-LIMITS, and the PRIORITY-LIMITS for jobs in the queue for your
printer. Use the SHOW PRINTER PARAMETERS command to see what values
have been set.
Some are initially set by default. You cannot set
parameters for a printer at another node.
With remote operator privileges you cannot use the SET command to set
parameters for other system devices and activities, except for your
terminal.
(See SET TERMINAL command.)
Format:
FORMS-TYPE name
LIMIT-EXCEEDED-ACTION
SET PRINTER

{~~~RT}
IGNORE

n

{~~~n}
PRIORITY-LIMITS {~~m}
PAGE-LIMITS

Where:
PRINTER

The printer at your remote station.

n

o for remote station printers.

FORMS-TYPE name

The name of the form you should put in the
printer.
The name is specified by your
systems programmer, or system administrator,
in SYS:LPFORM.INI.

LIMIT-EXCEEDED-ACTION
Action to take if the print job
specified output page limit.
action to take as follows:
ABORT
ASK
PROCEED
PAGE-LlMITS

exceeds the
Specify the

The print job terminates.
You are asked what to do (abort or continue).
The print job continues and the page limit is
ignored.
Maximum number of pages allowed for printed
o~t~ut
specified as a number
(nnnn), or
m1n1mum to maximum number of pages given as a
range
(n:m).
If you give a minimum, jobs
containing less than that number of pages are
not printed;
if you give a maximum, jobs
containing more than that number of pages are
not printed.

E-28

REMOTE STATION OPR COMMANDS .
PRIORITY-LIMITS

Priority limits of a particular print~r.
A
normal printer job for your printer receives
the system default priority (nn) specified by
your system administrator.
As the printer
operator, you can give apriority range for
your printer with the SET command.
The
priority must be in the range 1-63, with
higher numbers receiving service first. The
user can modify the priority of a job with
the MODIFY command or set the priority of a
job with a /PRIORITY switch.
A job with
priority outside the allowed range is queued
but not printed. An unprivileged user can
specify priority only as high as 20; he can
use priority 1 to print files in the order
entered, not smallest first.

Example:
aPR> SET PRINTER 0 LIMIT-EXCEEDED-ACTION ASK
aPR>

E-29

~

REMOTE STATION OPR COMMANDS
SET TERMINAL:

SETTING TERMTNAL CHARACTERISTICIS

The SET TERMINAL command sets the characteristics of the terminal from
which you are running aPR at your remote station.
You can specify
your terminal type and whether you wish to use the keys on your
terminal
keypad as function keys to issue aPR commands.
(The keypad
is the block of 15 keys, usually at the right,
separate from the
typewriter keyboard on your terminal.)
Format:
SET TERMINAL

{

KEYPAD
}
NOKEYPAD
TYPE
type

Where:
KEYPAD
Activates the keypad.
The active keys issue
(VT52 and
following aPR commands:
VT100 terminals
only)

the

Command

1
2
3
4
5
7
8
9

? help (lists all OPR commands)
SHOW STATUS
SHOW QUEUES
SHOW PARAMETERS
SHOW MESSAGES
SHOW ROUTE TABLE
clears screen
SHOW OPERATORS
SHOW QUEUE MOUNT-REQUESTS

NOTE
When you activate the keypad, you must press
each time you use recognition.
NOKEYPAD

Deactivates the keypad.

TYPE type

Gives your
terminal
characteristics:
Type

type

with

~

the

twice

following

Characteristics

33

Teletype
(R)
Model 33,
with
no
formfeed,
no tab, uppercase only, 72
characters wide, 66 lines long.

35

Teletype (R) Model 35, with formfeed,
tab,
uppercase only,
72 characters
wide, 66 lines long.

LA36

No formfeed, no tab,
both uppercase
dnd
lowercase,
132'characters wide,
66 lines long.

E-30

REMOTE STATION OPR COMMANDS
Type

Characteristics

LA120

Both uppercase and
lowercase,
characters wide, 66 lines long.

VT05

No formfeea,
with tab,
uppercase
only,
72 characters wide, 20 lines
long.

VT50

No formfeea, no tab, uppercase only,
80 characters wide, 12 lines long.

VT52

No formfeed, with tab, both upper and
lowercase,
80 characters wide,
24
lines long.

VT61

No formfeed, with tab, both upper and
lowercase,
80 characters wide,
24
lines long, local text editing.

VT100

No formfeed, with tab, both upper and
lowercase, 80 or 132 characters wide,
24 lines long,
smooth
low-speed
scroll, XON, XOFF.

Example:
OPR>SET TERMINAL TYPE

LA36~

Example using the keypad on a VT52:
OPR> SET TERMINAL KEYPAD

~

OPR> <8>
OPR>
14:03:31

--Operators--

Node
KL1026
CTCH22

132

system
remote

Terminal

Job

User

221
4

61
2

USER [67,1001]
OPR[122,2]

OPR>

E-31

REMOTE STATION OPR COMMANDS
SHOW:

DISPLAYING SYSTEM INFORMATION

The SHOW command displays information about the system.
Use it to display the date and time, the outstanding messages for your
remote station, the parameters set for your printer, the queues and
route tables, the network operators, and the status of printers and
card readers.
You can obtain information about a specific node with
the INODE switch. Because this command has several keywords with
several switches and parameters, each keyword applicable at a remote
station is described separately.
Format:
SHOW Keyword

[/NODE:nodenamel

Where:
Keyword

ALLOCATION
CONTROL-FILE
MESSAGES
OPERATORS
PARAMETERS
QUEUES
ROUTE-TABLE
STATUS
SYSTEM-LISTS
TIME

nodename

about
which
you
want
The name of the node
Always follow a nodename with a double
information.
colon (::); you can obtain the double colon with

GD .

E-32

REMOTE STATION OPR COMMANDS
SHOW ALLOCATION:

Displaying Allocations

The SHOW ALLOCATION command displays
allocations assigned at the host.

disk

and

tape

magnetic

Format:
SHOW ALLOCATION

}
ALL-REQUESTS
BATCH-REQUEST
[request-id]
{
JOB job-number

Where:
request-id

The request-id of a specific
omitted,
allocations
for
appear.

job-number

The number of a specific job.

batch request.
If
all batch requests

Example:
OPR>SHO ALLOC ALL
OPR>
15:50:51
Mountable Device Allocations -Allocation for job 4 OPSER [1,2]
Type
Volume set
Resource
----------------OSKB
OSKB
Structure
OSKC
Structure
OSKC

All

Own

1
1

1
1

Allocation for batch request 38 KILGORE [30,5000]
All
Type
Resource
Volume set

----------

--------

OSKP

RP20
OSKP

oisk unit
Structure

Allocation for job 59 COLBATH [10,10000]
Type
Volume set
Resource
----------------9TK 800/1600
Magtape unit
OSKB
OSKB
Structure
OSKC
Structure
OSKC
MTA-DK68H5
ATC8
Magtape vol.

E-33

Own

1
1

1
1

All

Own

1
1
1
1

0
1
1
0

REMOTE STATION OPR COMMANDS
SHOW CONTROL-FILE:

Displaying Batch-Stream Control Files

The SHOW CONTROL-FILE command displays the correct
control in use from a particular batch stream.

contents

of

the

Format:
SHOW

CONTROL-FILE

BATCH-STREAM

m [LINES:m]

Where:
n

The number of the batch stream.

m

The number of lines to display
file (1 to 15).

from

the

control

Example:
OPR> SHO CONTROL-FILE BA 0 /LINFS:3
aPR>
16:06:22
Batch-Stream 0 JOB #55 --Show control file-JOB ONE Req #789 for USER [30,4000]
*Input from DSKP:TEST.CTL [30,4000]*
*FORERR.RLS=FORERR.MAC
. i •• DIRECT/CHECKSUM
aPR>

E-34

REMOTE STATION OPR COMMANDS
SHOW MESSAGES:

Displaying Messages

The SHOW MESSAGES command displays any outstanding messages for your
remote station.
Use the RESPOND command to reply to a messagej or
simply take the indicated action. 'To use SHOW MESSAGES, you must
ENABLE
OUTPUT-DISPLAY
of
ALL-MESSAGES
(the
default)
or
ACTION-MESSAGES.
At the remote station, only the messages outstanding for your
are displayed.

station

Format:
SHOW MESSAGES [nnnn]

[/NODE:nodename]

Where:
Outstanding message number (0 to 9999).
If no
number
is entered, all outstanding messages, with
their sequence numbers, are displayed.

nnnn

nodename

. The' name of
information.

the

node

about

which

you

Examples:
OPR> SHOW MESSAGES G!D
OPR>
12:31:29
-- SYSTEM MESSAGES OUTSTANDING
12:30:30

OPR>SHO M
12:40:10

<47>

Batch-stream 1
JOB #19
SPRINT: Please START the card reader.
SEND message to User: [27,5117] when done.

/N:CTCH22::

G!D

-- No Messages for Node CTCH22(22) --

OPR>
NOTE
You can use recognition (with ~) on all keywords, but
you cannot use recognition on a nodename.

E-35

want

REMOTE STATION OPR COMMANDS
SHOW OPERATORS:

Displaying Network Operators

The SHOW OPERATORS command displays information about all users in the
network who are running OPR.
You can use the /NODE switch to display
only the users who are running OPR at a given node.
Format:
SHOW OPERATORS [/NODE:nodename]
Where:
nodename

Specifies the name of a node.

Example:
OPR>SHOW OPERATORS
OPR>
14:03:31
Node
KLl026
CTCH22

--Operators-~

system
remote

Terminal
221
354

Job

6I
2

OPR>

E-36

User
USER[6'7;l 001]
OPR[170,2]

REMOTE STATION OPR COMMANDS
SHOW PARAMETERS:

Displaying Printer Parameters

The SHOW PARAMETERS command displays the parameters set for a
on a batch stream.

printer

Format:
fBATCH-STREAM)

SHOW PARAMETERS

1PRINTER

. n

[/NODE:nodename: :]

Where:
PARAMETERS

Printer and batch stream characteristics
which values can be set.

BATCH-STREAM

The batch streams established on your host.

PRINTER

The printer.

n

Unit number of the OPR object;
0 for your
remote station printer, 0 to system limit for
batch streams.

for

Example:
OPR>SHOW PARAMETERS PRINTER 0
OPR>

07:35:07

~

-- System Device Parameters--

Printer Parameters:
Unit
Node
Page Limits

o

DN200(20)

1:500

Form

Prio

NORMAL

1:63

Lim-Ex
Ask

OPR> SHOW PARAMETERS BATCH-STREAM 0 ~
OPR>
14:18:55

--System Device Parameters--

Batch-Stream Parameters:
Strm

-0-

Minutes

0:3600

Prio

1:63

Opr-Intvn
Yes

OPR>

E-37

Dev-Chars
Lower

REMOTE STATION OPR COMMANDS
SHOW QUEUES:

Displaying Queued Jobs

The SHOW QUEUES command displays the list of jobs that are waiting
in
d
queue to be processed and any jobs that have been held for
rescheduling.
You can display all jobs for your
remote station or
only batch or printer
jobs.
If a job for which a HOLD command has
been specified is displayed, the IHOLD switch is also displayed.
Format:
SHOW QUEUES

ALL-JOBS
BATCH-JOBS
CARD-PUNCH-JOBS
MOUNT-REQUESTS
PAPER-TAPE-PUNCH-JOBS
PLOTTER-JOBS
PRINTER-JOBS

/ALL
INODE: nodename : :]
ISHORT
[ IUSER: [p ,pn]

Where:
ALL-JOBS

All jobs in all system queues.

BATCH-JOBS

Only jobs in the batch input queue.

CARD-PUNCH-JOBS

Jobs queued
punch.

MOUNT-REQUESTS

Requests to mount a structure.

PAPER-TAPE-PUNCH-JOBS

Jobs queued for the host paper tape
punch.

PLOTTER-JOBS

Jobs queued for the host plotter.

PRINTER-JOBS

Jobs queued for the prfnters.

/ALL

Displays complete informaiion
the queued job or request.

on

INODE:nodename: :

Displays information on a
request at the given node.

job

or

/SHORT

Displays an abbreviated version
the information.

of

IUSER: [PPN]

Displays information on jobs
requests for a specific [PPN].

or

E-38

fqr

the

host

card

REMOTE STATION OPR COMMANDS
Examples:
OPR) SHOW QUEUES PRINTER-JOBS ~
OPR)
14:26:16
~- System Queues Listing
Printer Queue:
Job Name Req#. Limit

User

LPTEST
317
108
ACARLSON
/Lower
There is 1 Job in the Queue (None in Progress)
OPR)SHO Q/BA
OPR)
14:31:40
Batch Queue:
*ELAPSE
15
BACKUP
13

--System Queues Listing-01:00:00
00:05:00

User [PPN]
User [PPN]

OPR)

E-39

/Dest:DN200

REMOTE STATION OPR COMMANDS
SHOW ROUTE-TABLE:

Displaying Node Routing Tables

The SHOW ROUTE-TABLE command displays the routing tables of the nodes
whose output has been transferred with the ROUTE command.
At the
remote station, you can display only the routing that has been
performed for your station by the system operator at the host.
Example:
aPR> SHOW ROUTE-TABLE
aPR>
15:04:17

-- System Device Routing Table --

Printer 0 [COMET(70) ] Routed to Printer 0 [NEXT(27) ]
aPR>

E-40

REMOTE STATION aPR COMMANDS
SHOW SYSTEM-LISTS:

Displaying Dump, Swapping and Search Lists

The SHOW SYSTEM-LISTS command displays lists of structures that
contain the crash dumps, active swapping, and the system search lists
at the TOPS-lO host.
Format:
SHOW

SYSTEM-LISTS

Example:
aPR> SHO SYS
aPR>
16:40:21

~

-- System lists -Crash Dump List:
Active Swapping List:
System Search List:

aPR>

E-4l

DSKN:, DSKC:, DSKB:, BLKX:
RPBO:, RPA3:, RPB5:, RND2:
DSKC:, DSKB:

REMOTE STATION OPR COMMANDS
SHOW STATUS:

Displaying Device/System Information

The SHOW STATUS command displays the current status of batch streams,
devices,
and nodes in the network.
You can use this command to
determine whether your devices are active or
idle,
and if network
nodes are on-line or off-line.
If you omit the PRINTER or READER
keyword, all devices at your station for which scheduling has been
started are displayed.
Format:

SHOW STATUS

BATCH-STREAM
CARD-PUNCH
DISK-DRIVE
NETWORK-NODE
PAPER-TAPE-PUNCH
PLOTTER
PRINTER
READER
STRUCTURE
TAPE-DRIVE

[/NODE :nodename: :]

[/SHORT]

Where:
BATCH-STREAM

Specifies a batch input stream.

CARD-PUNCH

Specifies a card punch.

DISK-DRIVE

Specifies a disk drive.

NETWORK-NODE

Specifies a node in the network.

PAPER-TAPE-PUNCH

Specifies a paper tape punch.

PLOTTER

Specifies a plotter.

PRINTER

Specifies a printer.

READER

Specifies a card reader.

STRUCTURE

Specifies a disk structure.

TAPE-DRIVE

Specifies a tape drive.

nodename: :

Gives status of the given node.

/SHORT

Displays an abbreviated version
of
the
status.
If /SHORT is not specified, complete
information is displayed.

E-42

REMOTE STATION OPR COMMANDS
"Examples:
OPR>SHOW STATUS PRINTER

~

-- System Device Status -Printer Status:
Unit
Node

Status

Jobname

Req#

User

o

DN200(20)
Active
NRM
14
[27,5117]
Started at 19:28:55, printed 0 of 27 pages
NOTE
The last three columns
active device.

OPR> SHO ST NET
OPR>
14:43:13
Node Name
KL1026(26)
COMET(70)

appear

only

if

~

--System Network Status-Status
On-line
Off-line

(There are 2 Nodes in the Network)
OPR>SHO ST NET /NODE: COMET:: ~

E-43

there

is

an

REMOTE STATION aPR COMMANDS
SHOW TIME:

Displaying Date and Time

The SHOW TIME command displays the current date and time.
The date is
shown
in the
form dd-mmm-yy (day, month, year) and the time in the
form hh:mm:ss (hour, minutes, seconds).
Format:
SHOW TIME
Example:
OPR>SHOW TIME C~
I-Dec-80 11:55:34
OPR>

E-44

REMOTE STATION CPR COMMANDS
SHUTDOWN:

TERMINATING DEVICE SCHEDULING

The SHUTDOWN command terminates scheduling for a specified device at
your
remote station. When you issue a SHUTDOWN command, the current
job that is processing continues until
it is completed.
Then
scheduling of jobs for the device terminates, and no further jobs that
require the device are processed.
With remote operator privileges for
your
remote station,
you
terminate scheduling only for your own printer or card reader.

can

Format:

f PRINTER}

SHUTDOWN

\ READER

n

Where:
PRINTER

The printer at your remote station.

READER

The card reader at your remote station.

n

o

for remote station card readers, 0 for remote station

printe~s.

Example:
OPR>SHUTDOWN PRINTER 0 ~
OPR>
16:23:07
Printer 0 [DN200(20)]

-- Shutdown Scheduled --

OPR>
You cannot use the following keywords
operator privileges:
BATCH-STREAM
CARD-PUNCH
NODE
PAPER-TAPE-PUNCH
PLOTTER
/NODE

E-45

to

this

command

with

remote

REMOTE STATION OPR COMMANDS
START:

STARTING DEVICE SCHEDULING

The START command starts scheduling for your
Use it to restart scheduling terminated by
remote operator privileges at the remote
scheduling only for your own line printer or

printer or card reader.
a SHUTDOWN command. With
station, you can start
card reader.

Format:
START

PRINTER}
{ READER

n

Where:
PRINTER

The printer at your remote station.

READER

The card reader at your remote station.

n

o for remote station card
remote station printers.

readers,

0

for

Example:
aPR> START PRINTER 0 C~
aPR>
20:03:09
Printer 0 [DN200(20)]

-- Startup Scheduled --

aPR>
You cannot use the following keywords and switch to this command
remote operator privileges:
BATCH-STREAM
CARD-PUNCH
NODE
PAPER-TAPE-PUNCH
PLOTTER

INODE

E-46

with

REMOTE STATION OPR COMMANDS
STOP:

STOPPING DEVICES TEMPORARILY

The STOP command temporarily stops your printer or card
reader.
The
device remains active.
It is not shutdown and jobs requesting that
device can still be scheduled.
Restart a stopped device with a
CONTINUE command.
Format:
STOP

PRINTER}
{ READER n

Where:
PRINTER

The printer at your remote station.

READER

The card reader at your remote station.

n

o for remote station card readers, 0 for remote station
printers.

Example:
OPR>STOP READER 0 ~
aPR>
21:04:37
Reader 0 [DN200(20)]

-- Stopped --

aPR>
You cannot use the following keywords and switch to the
remote operator privileges:
BATCH-STREAM
CARD-PUNCH
PAPER-TAPE-PUNCH
PLOTTER

INODE

E-47

command

with

REMOTE STATION OPR COMMANDS
SUPPRESS:

SUPPRESSING CARRIAGE CONTROL

The SUPPRESS command suppresses the printing of bl'ank lines on your
printer.
When you issue a SUPPRESS command, all formfeed and blank
lines in the
job to be printed are
ignored.
All output
is
single-spaced.
Format:
SUPPRESS PRINTER n

/FILE]
/JOB
[ /STOP

Where:
PRINTER

The printer at your remote station.

n

o

/FILE

Suppresses blank lines for the file
printed.

/JOB

Suppresses blank lines for
the current job being
printed,
regardless of how many files were specified
when the job was originally queued to print.
This is
the default.

/STOP

Resumes normal printing.
The job currently printing
reverts back to the print format in effect before the
SUPPRESS command was issued.

for the printer at a remote station.
currently

being

Example:
OPR) SUPPRESS PRINTER 0 /FILE ~
OPR)
18:23:45
Printer 0 [DN200(20)]

-- Suppressed --

OPR)
You cannot use the following
operator privileges:

switch

/NODE

E-48

to

this

command

with

remote

REMOTE STATION OPR COMMANDS
TAKE:

USING A COMMAND FILE

Use the TAKE command to execute the commands in a previously made
file.
The file must contain OPR commands that are valid for your
remote station.
Format:
TAKE

J

/DISPLAY
[ /NODISPLAY

filespec

Where:
filespec

The file specification of the file containing
commands to be executed.

/DISPLAY

Displays events and messages on your terminal as
the command file executes.
This is the default.

/NODISPLAY

Does not
executes.

display

output

as

the

command

OPR

file

Example:
Prepare a file
following lines:

called

TEST.OPR

with

any

editor

containing

sho sta ba 0
sho g pri
Run OPR and use the following command:
OPR>TAKE TEST.OPR
OPR>
17:04:22

~

-- System Device Status --

Batch-Stream Status
Strm
Status
Jobname

o

Reg#

User

Active
NEW
831
USER [50,2000]
Job 19 Running MOUNT Runtime 0:00:01

17:04:22

System Queues Listing --

Printer Queue:
Jobname
Req#

Limi t

User

*LDDN22

915
225
USER [50,2000]
Waiting for Operator Intervention
*15649
924
147
ASG [60,3000]

On Unit:O
On Unit:l

[There are 2 jobs in the queue (2 in progress)]
aPR>

E-49

the

APPENDIX F
USING SPECIAL PRINT FORMS

Using special forms at a
remote site is no different from using
special
forms at the host.
You place specifications describing forms
to be printed on your printer in SYS:LPFORM.INI, the file at the host
that contains the specifications for the special forms.
The system
administrator must set up the file protection for LPFORM.INI so that
you, as the remote operator, can alter it.
SYS:LPFORM.INI must always
exist.
Each line in LPFORM.INI is of the form:
formname/SW/SW/SW .•.
or
formname:locator/SW/SW/SW .••
Where:
formname

is a 1- to 6-character (SIXBIT) form name.
Use form
names descriptive of the forms needed at your site.

:locator

names the printer whose form the line
describes.
The locator can be:
ALL
LOCAL
REMOTE
LPTxxy

/SW

in

LPFORM.INI

all printers (default)
local host printer
all remote station printers
printer unit y at node xx

specifies one or more switches (see Table E-4)
Table F-4
LPFORM.INI Switches

Switch

Function

/ALCNT:n

The number of times
(n)
to print the
The default is 5 times;
alignment file.
the switch is optionally used with the
/ALIGN switch.

/ALIGN[:filespec]

A I- to 6-character (S IXBIT) alignment file
name . used to position the specified form.
If the filespec is omitted, the default is
formname.ALP;
if the extension is omitted,
the default extension is .ALP.

F-1

USING SPECIAL PRINT FORMS
Table F-4 (cont.)
LPFORM.INI Switches
Function

Switch
/ALSLP:n

The number
printing
default is
optionally

/BANNER:nn

The number of banner
(job header)
(nn) to print. The default is 2.

/CHAIN:xxx
or
/DRUM:xxx

A 1- to 6-character (SIXBIT) string giving
the name (xxx) of a chain or drum to use on
the printer. When the form is scheduled,
the name of the chain or drum appears on
your terminal.

/HEADER:nn

The number of header pages (nn)
The default is 2.

/LINES:nn

The number of lines (nn) to print
page. The default is 60.

/NOTE:note

A note of up to 50 characters that
on your OPR terminal when the
scheduled.

/RAM:filespec

A 1- to 6-character (SIXBIT)
filespec
containing the translation RAM needed for a
64- or 96-character printer with a loadable
RAM.
Standard RAM files are distributed
with the system software.
You
cannot
change them.

/RIBBON:name

A 1- to 6-character string that names the
type of ribbon to use on your printer. The
ribbon name appears on your terminal when
the form is scheduled.

/TRAILER:nn

The number of trailer pages (nn)
at the end of each job.

/WIDTH:nnn

The width of the line to print on the
banner, header, and trailer pages. LPTSPL
converts the value (nnn) to a width class.
It prints these identifying pages in one of
three widths:
Class

-12
3

of seconds to sleep between each
of
the alignment file.
The
about 7 seconds; the switch is
used with the /ALIGN switch.

Value(nnn)
o to 60
61 to 100
101 to 132

F-2

pages

to

print.
on

each

appears
form is

to

print

Characters Per Line
up to 66
up to 90
up to 129

USING SPECIAL PRINT FORMS
When a request for a new form is made, LPTSPL searches LPFORM.INI for
the first
line containing the requested formname and the appropriate
locator.
When a match is found,
the switches specified are used.
LPTSPL uses the first correct match it finds, readinq LPFORM.INI
line-by-line.
The user at a remote site terminal can type:
PRINT

filename/FORMS:narrow~

(A user at any other site must use the /DEST switch to print at your
remote station.)
Executing this PRINT command places a print request
in the queue for the printer at your remote station.
As the operator
at the
remote station, you can check the print queue periodically to
see if any requests are waiting.
For example, you can use the SHOW QUEUE PRINTER
queue:
OPR> SHO Q PRI
OPR>
15:19:18
Printer Queue
Job Name
Req#

657

SWIT~

command

to

see

the

~

System Queues Listing -Limit
-7-

User
USER [27,5000]/FORMS:NARROW/DEST:COMET(20)

There is 1 job in the queue

(none in progress)

OPR>
When you see a print request waiting, issue a SET PRINTER FORMS-TYPE
command
to activate use of the system file SYS:LPFORM.INI.
For
example, your host system area contains an LPFORM.INI file with a
forms specification as follows:
NARROW: LPT200/VFU:NORMAL/WIDTH:72
width of form
vertical format unit
printer unit number
node number
form name
When a print request for
the special
form
execute your SET command.
For example,

appears

in

the

OPR> SET PRINTER 0 FORMS-TYPE NARROW ~
OPR>
14:13:21
Printer 0 -- Set Accepted
OPR>
14:13:21
Printer 0 -- Begin
Job LPTSPL Req #657 for USER [27,5000]
OPR>
14:13:21 <26> Printer 0
Please load forms type 'NARROW'
Type 'Respond  CONTINUE' When Ready

F-3

queue,

USING SPECIAL PRINT FORMS
The message you see gives a message number «26> in the example) and
shows the form name (NARROW). This must be the same name as given by
the user in his print request. If no job is currently printing on
your printer, the messages appear immediately at your terminal:
otherwise, they appear only after your current job is completed.
The
system operator or host operator at the site where you log in can also
place SET commanos in the system file SYS:SYSTEM.CMD.
For example,
SYSTEM.CMD might contain the following set command for your site:
SET PRINTER O/NODE:20::

PAGE-LIMIT 2000

node number
unit number
When you see the "load forms type" message, go to the printer and
insert the appropriate forms. Be sure to place the printer on line
when done. Then issue a RESPOND command to restart printing~
for
example, use the following:
OPR>RES 26 CONTINUE (RET)
OPR>
Loading VFU with 'NORMAL' -Printer 0
14:15~14
OPR>
14:16:44
Printer 0
End
OPR>
14:16:44
Printer 0
End
Job LPTSPL Reg #657 for USER [27,5000]
OPR>
To return to normal forms, use:
SET

PRIN

0

FORM

NORMAL

and repeat the above procedure, changing the form and issuing the
RESPOND command.
These are the normal procedures for controlling
forms at your remote site.

F-4

INDEX

ABORT command, E-7
ALIGN command, E-8
Aligning printer forms, E-8
Allocations,
displaying, E-33
Alternate load path, B-4
ASCII character set, C-2

Command (Con t. )
CONTINUE, E-ll
DISABLE, E-12
ENABLE, E-14
EXIT, E-16
FORWARDSPACE, E-17
HELP, E-18
HOLD, E-19
LOCATE, 2-9
MODIFY, E-20
NETWORK, 3-2
NEXT, E-22
PRINT, 3-2
QUEUE, 3-2
RELEASE, E-23
REPORT, E-24
REQUEUE, E-25
RESPOND, E-26
Route, 2-9
SEND, E-27
SET HOST, 3-1
SET PRINTER, E-28
SET TERMINAL, E-30
SHOW, E-32
SHOW ALLOCATION, E-33
SHOW CONTROL-FILE, E-34
SHOW MESSAGES, E-35
SHOW OPERATORS, E-36
SHOW PAR.AMETERS, E-37
SHOW QUEUES, E-38
SHOW ROUTE-TABLE, E-40
SHOW status, E-42
SHOW STATUS NETWORKS, 2-9
SHOW SYSTEM-LISTS, E-4l
SHOW TIME, E-44
SHUTDOWN, E-45
START, E-46
START PRINTER, 2-10
STOP, E-47
SUBMIT, 3-3
SUPPRESS, E-48
TAKE, E-49
Command file,
using a, E-49
Command functions,
OPR, E-l
Commands,
OPR, E-4
Comments,
recording, E-24
Components,
DN200, 1-3
DN80-series, 1-2
remote station, 1-1
Concentrator,
DN200, 1-3

Back panel,
card reader, 2-17
Back panel switches,
card reader, 2-17
BACKSPACE command, E-9
Backspacing print requests,
E-9
Batch control files,
displaying, E-34
Batch jobs,
submitting, 3-3
Baud rate switches, 2-13
BOOT, 1-1, 2-1
Bootstrap switches,
NETLDR, B-1
Bootstrapping, 2-1

CANCEL command, E-IO
Canceling print requests,
E-IO
Card,
punched, C-l
Card reader, 2-15
back panel, 2-17
back panel switches, 2-17
front panel, 2-16
lamps, 2-16
operations, 2-18
starting, 2-10
switches, 2-16
Carriage control,
suppressing, E-48
CDRIVE, 2-7
Character set,
ASCII, C-2
Characters,
Ascii, C-5
CHKll, 4-1
CHKll messages, 4-1
Command,
ABORT, E-7
ALIGN, E-8
BACKSPACE, E-9
CANCEL, E-IO
Index-l

INDEX (CaNT.)

Concentrator (Cont.)
DN80-series, 1-2
Concentrators,
remote, 1-1
Console,
lamps, 2-15
operator's, 2-13
CONTINUE command, E-ll
Control files,
displaying batch, E-34
Control panel,
DN200, 1-3
DN82, 1-2

DN82, 1-1
control panel, 1-2
remote station, 1-2

ENABLE command, E-14
Error,
hardware, 4-1
messages, 4-2
reporting, E-24
system messages, 4-2
Error messages,
aPR, 2-8
 key, 2-8
EXIT command, E-16
Exiting from subjob, 2-20
Exiting aPR, E-16

Date and time,
displaying, E-44
Default load path, B-2
Default load requests, B-2
Device,
displaying information,
E-42
relocating station, 2-9
restarting, E-ll
starting, 2-11
stopping, E-47
Device scheduling,
starting, E-46
terminating, E-45
DISABLE command, E-12
Displaying,
allocations, E-33
batch control files, E-34
date and time, E-44
device information, E-42
messages, E-35
network operators, E-36
printer parameters, E-37
queued jobs, E-38
routing, E-40
system information, E-32,
E-42
system lists, E-4l
DN200, 1-1
components, 1-3
concentrator, 1-3
control panel, 1-3
remote station, 1-3
starting the, 1-1
DN80, 1-1
DN80-series,
components, 1-2
concentrator, 1-2
remote station, 1-2
starting the station, 1-1
DN80-series station,
starting the, 1-1

File,
using a command, E-49
Files,
skipping print, E-17
Forms,
aligning printer, E-8
special print, F-l
FORWARDSPACE command, E-17
Front panel,
card reader, 2-16
Functions,
aPR command, E-l

Glossary, D-l

Hardware, 2-12
error, 4-1
HELP command, E-18
HOLD command, E-19
Holding queued jobs, E-19
Host,
operator, 2-6
system, 1-1
TOPS-lO, 1-1

Information,
displaying device, E-42
displaying system, E-32,
E-42
obtaining, E-18

Index-2

INDEX (CaNT.)

Installation,
software, 1-1

Messages (Cont.)
startup, 2-3, 2-5
Station, 4-3
system error, 4-2
Mode switches, 2-13
MODIFY command, E-20
Modifying requests, E-20

Jobs,
displaying queued, E-38
holding queued, E-19
releasing queued, E~23
rescheduling, E-25
specifying queued, E-22
terminating, E-7

NETLDR bootstrap switches,
B-1
NETLDR messages, B-3
NETLDR program, 2-1
NETLDR.INI, B-2
NETWORK command, 3-2
Network operators,
displaying, E-36
NEXT command, E-22

Key,
, 2-8

LA36 terminal, 2-13
Lamps,
card reader, 2-16
console, 2-15
Line printer,
LP05, 2-18
Lists,
displaying system, E-4l
Load path,
alternate, B-4
default, B-2
Load requests,
default, B-2
LOCATE command, 2-9
Logg ing in, 2-4
subjobs, 2-12
Logging in subjob, 2-12
Logging out, 2-20
Logout messages, 2-20
LP05 line printer, 2-18
LPFORM. INI, F-l
switches, F-l
LPTSPL, 2-7

Objects,
aPR, E-3
Obtaining information, E-18
Operations,
card reader, 2-18
printer, 2-19
Operator, 2-6
host, 2-6
p r i viI eg e s, 2 - 6
remote, 2-7
system, 2-6
Operator procedures, 2-1
Operator's console, 2-13
Operators,
displaying network, E-36
aPR,
error messages, 2-8
exiting, E-16
starting, 2-7
aPR command functions, E-l
aPR commands, E-4
aPR objects, E-3
OPSER, 2-11
ORION messages, 2-7

Message,
starting displays, E-14
stopping displays, E-12
Messages, 2-3
CHKll, 4-1
displaying, E-35
error, 4-2
logout, 2-20
NETLDR, B-3
aPR error, 2-8
ORION, 2-7
responding to, E~18, E-26
sending, E-27

Parameters,
displaying printer, E-37
setting printer, E-28
setting terminal, E-30
Path,
alternate load, B-4
default load, B-2
PDP-II, 1-1
PRINT command, 3-2

Index-3

INDEX (CONT.)

Print files,
skipping, E-17
Print forms,
special, F-l·
Print requests,
backspacing, E-9
canceling, E-IO
Printer,
alarm indicators, 2-19
alarm lamp, 2-19
LP05 line, 2-18
operations, 2-19
starting, 2-10
Printer forms,
aligning, E-8
Printer parameters,
displaying, E-37
setting, E-28
Printing, 3-2
Privileges,
operator, 2-6
Procedures,
operator, 2-1
Program,
NETLDR, 2-1
Punched card, C-l

Remote station ROM switches,
A-I
Remote station tasks, 2-9
REPORT command, E-24
Reporting,
error, E-24
Requests,
default load, B-2
modifying, E-20
REQUEUE command, E-25
Rescheduling jobs, E-25
RESPOND command, E-26
Responding to messages,
E-18, E-26
Restarting device, E-ll
Restarting station, 2-4
ROM, 1-1, 2-1
ROM switches,
Remote station, A-I
Routing,
displaying, E-40

Scheduling,
starting device, E-46
terminating device, E-45
SEND command, E-27
Sending messages, E-27
Set,
ASCII character, C-2
SET HOST command, 3-1
SET PRINTER command, E-28
SET TERMINAL command, E-30
Setting,
printer parameters, E-28
terminal parameters, E-30
SHOW ALLOCATION command,
E-33
SHOW command, E-32
SHOW CONTROL-FILE command,
E-34
SHOW MESSAGES command, E-35
SHOW OPERATORS command,
E-36
SHOW PARAMETERS command,
E-37
SHOW QUEUES command, E-38
SHOW ROUTE-TABLE command,
E-40
SHOW status command, E-42
SHOW STATUS NETWORKS
command, 2-9
SHOW SYSTEM-LISTS command,
E-4l
SHOW TIME command, E-44
SHUTDOWN command, E-45
Skipping print files, E-17

QUEUE command, 3-2
Queued jobs,
displaying, E-38
holding, E-19
releasing, E-23
specifying, E-22

Reader,
card, 2-15
Recognition,
Us ing, 2-8
Recording comments, E-24
RELEASE command, E-23
Releasing queued jobs, E-23
Relocating station device,
2-9
Remote,
concentrators, 1-1
operator, 2-7
station components, 1-1
Remote station, 1-1
DN200, 1-3
DN80-series, 1-2
DN82, 1-2
ROM switches, A-I
starting, 2-1
Remote station DN82, 1-2

Index-4

INDEX (CaNT.)

Suppressing carriage
control, E-48
Switches,
baud rate, 2-13
card reader, 2-16
card reader back panel,
2-17
LPFORM.INI, F-l
mode, 2-13
NETLDR bootstrap, B-1
Remote station ROM, A-I
System,
displaying information,
E-42
host, 1-1
operator, 2-6
System information,
displaying, E-32
System lists,
displaying, E-4l

Software installation, 1-1
Special print forms, F-l
Specifying queued jobs,
E-22
START command, E-46
START PRINTER command, 2-10
START READER, 2-10
Starting,
card reader, 2-10
device, 2-11
device scheduling, E-46
messages displays, E-14
aPR, 2-7
printer, 2-10
remote station, 2-1
station, 2-2
the DN200, 1-1
the DN80-series station,
1-1
Startup messages, 2-3, 2-5
Station,
messages, 4-3
remote, 1-1
restarting, 2-4
starting, 2-2
starting the DN80-series,
1-1
Station components,
remote, 1-1
Station device,
relocating, 2-9
Status command,
SHOW, E-42
STOP command, E-47
Stopping,
device, E-47
message displays, E-12
Subjob,
exiting from, 2-20
logging in, 2-12
Subjobs, 2-11
SUBMIT command, 3-3
Submitting batch jobs, 3-3
SUPPRESS command, E-48

TAKE command, E-49
Tasks,
remote station, 2-9
Terminal,
LA36, 2-13
Terminal parameters,
setting, E-30
Terminating,
device scheduling, E-45
jobs, E-7
Time,
displaying date and, E-44
TOPS-IO host, 1-1
Trouble-shooting, 4-2

Using,
a command file, E-49
recognition, 2-8

Index-5

TOPS-10
Remote Station Guide
AA-D783B-TB

READER'S COMMENTS
NOTE:

This form is for document comments only. DIGITAL will use comments submitted on
this form at the company's discretion. If you require a written reply and are eligible to
receive one under Software Performance F{eport (SPR) service, submit your comments on an SPR form.

Did you find this manual understandable, usable, and well-organized? Please make suggestions for improvement.

Did you find errors in this manual? If so, specify the error and the page number.

Please indicate the type of reader that you most nearly represent.

o
o
o
o
o
o

Assembly language programmer
Higher-level language programmer
Occasional programmer (experienced)
User with little programming experience
Student programmer
Other (please specify)~~~~~~~~~~~~~~~~~~~~~

Name~

__________________

Organization
Street __________________

~

~

______

~

_____ Date ___________________

~

Telephone _____________
______________________________________

City _____________________________ State _____ Zip Code ______
or Country

.- -

a

-~-.- -oDOmNotoTear

f

ld
FmHD~e and Tape - - - - - - - - - - - - - - - - - - - - - - ~ -111--------~~~~;:;~~ -O

•

-III

if Mailed in the
United States

BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 33 MAYNARD MASS.
POSTAGE WILL BE PAID BY ADDRESSEE

SOFTWARE PUBLICATIONS

200 FOREST STREET
MARLBOROUGH, MA

- - - - -

Do Not Tear - Fold Here and Tape

I
I
I
I

MR01-2/L 12
01752

-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

I
I



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:56:37
Create Date                     : 2002:10:14 15:52:58Z
Creator Tool                    : g4pdf
Modify Date                     : 2010:02:11 00:16:11-08:00
Metadata Date                   : 2010:02:11 00:16:11-08:00
Producer                        : Adobe Acrobat 9.3 Paper Capture Plug-in
Format                          : application/pdf
Document ID                     : uuid:d92d13e0-852a-4c19-867c-d1922e8828ba
Instance ID                     : uuid:d3bf6feb-d422-4423-91b8-9d7547dacbb5
Page Mode                       : UseOutlines
Page Count                      : 116
Creator                         : g4pdf

EXIF Metadata provided by EXIF.tools