Manuale SDA_en AGREX SDA500 600

User Manual: AGREX SDA500-600

Open the PDF directly: View PDF .
Page Count: 64

English

USER AND MAINTENANCE MANUAL

IMPORTANT! Carefully read this manual before

using the machine.

Translation of the original instructions

AGREX S.p.A.

Via Balla, 55/57 - Loc. Taggì di Sotto - 35010 Villafranca Padovana (PD)

Tel. +39 049 50 00 000 - Fax. +39 049 90 75 524

e-mail: info@agrex.com - web site: www.agrex.com

P/N MNenSDA500600CER08 - 04.2014

SDA

500/600

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

2 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

SUMMARY

1 SECTION – GENERALITY .......................................................................................................... 5

1.1 PRESENTATION ........................................................................................................................... 5

1.1.1

Who the manual is intended for .......................................................................................... 5

1.2 CONDITION OF GUARANTEE ............................................................................................................ 6

1.2.1

Voidance of the guarantie .................................................................................................. 6

1.3 CUSTOMER SERVICE ..................................................................................................................... 7

2 SECTION – GENERAL FEATURES .............................................................................................. 8

2.1 MACHINE MARKINGS ..................................................................................................................... 8

2.1.1

Spreader description .......................................................................................................... 9

2.1.2

Scheduled use ................................................................................................................. 10

2.1.3

Non-scheduled use .......................................................................................................... 10

2.2 CONTROL DEVICES ..................................................................................................................... 10

2.3 TECHNICAL DATA ....................................................................................................................... 11

2.4 STANDARDS APPLIED .................................................................................................................. 11

3 SECTION – SAFETY AND ACCIDENT PREVENTION ................................................................ 12

3.1 SAFETY ................................................................................................................................... 12

3.1.1

General safety rules ......................................................................................................... 13

3.1.2

Safety signs .................................................................................................................... 14

3.2 SAFETY DEVICES ........................................................................................................................ 16

3.3 NOISE HAZARD ......................................................................................................................... 16

3.4 DUST HAZARD .......................................................................................................................... 16

3.5 CLOTHING ............................................................................................................................... 16

3.6 ECOLOGY AND POLLUTION ............................................................................................................ 16

3.7 SAFE USE ................................................................................................................................ 17

4 SECTION - HANDLING AND INSTALLATION .......................................................................... 19

4.1.1

Assembly of hopper extensions ........................................................................................ 19

4.2 HANDLING ............................................................................................................................... 20

4.3 HITCHING ............................................................................................................................... 20

4.4 PRELIMINARY CLEANING .............................................................................................................. 22

4.5 GENERAL INSPECTION ................................................................................................................. 22

5 SECTION – USE ...................................................................................................................... 23

5.1 PRIOR TO USE .......................................................................................................................... 23

5.2 STARTING UP ........................................................................................................................... 23

5.3 ADJUSTMENTS .......................................................................................................................... 23

5.3.1

Product spreading adjustment .......................................................................................... 23

5.3.2

Spreading width adjustment ............................................................................................. 24

5.3.3

Spreading patterns .......................................................................................................... 25

5.3.4

Loading the machine's hopper .......................................................................................... 26

5.3.5

Distribution ..................................................................................................................... 26

5.3.6

Driving technique suggestions .......................................................................................... 26

5.3.7

Late top-spreading .......................................................................................................... 26

5.3.8

Side spreading conveyor (optional) ................................................................................... 27

6 SECTION – MAINTENANCE .................................................................................................... 28

6.1 ROUTINE MAINTENANCE .............................................................................................................. 28

6.1.1

Daily cleaning ................................................................................................................. 28

6.1.2

General checks ................................................................................................................ 28

6.1.4

Spreading paddle assembly/disassembly............................................................................ 28

6.2 EXTRA MAINTENANCE .................................................................................................................. 29

3 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

6.3 TO KEEP IN MOTHBALL ................................................................................................................ 29

6.4 RE-START ................................................................................................................................ 30

6.5 DISMANTLING THE MACHINE ......................................................................................................... 30

7 SECTION – SPARE PARTS ...................................................................................................... 31

8 ANNEX A - STABILITY OF THE TRACTOR DISTRIBUTOR COMBINATION

SPREADING TABLES

4 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

1 SECTION – Generality

1.1 Presentation

This manual gives information, instructions and everything else you will need to understand, correctly oper-

ate and perform routine maintenance on spreaders mod. «SDA», hereinafter also referred to as the ma-

chine, and of all the accessories produced by AGREX Spa of Villafranca Padovana (Padua) Italy, here-

inafter also referred to as the Manufacturer.

You will not find a complete description of the various parts, or a detailed explanation of how they work

herein. Nonetheless, you will find all the information you will usually need to operate the machine safely and

to look after it properly.

Compliance with the instructions herein, together with careful, meticulous maintenance, is the only way to

assure proper operation, lasting service and economic running of the machine.

Failure to comply with the provisions herein, negligent operation, incorrect use of the machine or perform-

ance of unauthorized changes may lead to the Manufacturer declaring its warranty covering the machine

void.

THE MANUFACTURER ALSO DECLINES ANY RESPONSIBILITY FOR DAMAGES AS A RESULT OF

THE ABOVE-MENTIONED ACTIONS OR FOLLOWING FAILURE TO COMPLY WITH THE INSTRUC-

TIONS HEREIN.

For any repairs or overhauls entailing operations of some complexity, you must contact an authorized Cus-

tomer Support Centre with specialized personnel, or the actual Manufacturer, who will be glad, in any case,

to assure prompt, accurate technical servicing and anything else required to restore the machine to full

working order.

WARNING

This manual is an integral part of the machine and must be kept with the machine at all times, even when it

is moved or sold. It must be kept in a safe place where personnel in charge of work on the machine know

where to find it. Said personnel must look after it and keep it intact for future reference for the entire dura-

tion of the machine’s service life.

If it is damaged or misplaced, you must ask the Manufacturer for a copy without delay.

1.1.1 Who the manual is intended for

This manual is an essential tool for personnel who, in their various capacities, are somehow involved with

the machine.

The various job profiles are given below:

USER: A user is the person, or body, or company who has purchased or hired the plant and who intends to

use it for its intended purposes. They are responsible for the machine and for the training of anyone in-

volved with it.

OPERATOR: skilled technical personnel sent by AGREX S.p.A. to install the machine and train operators.

Technicians are able to perform operations of a complex nature on the plant, or any work in unusual situa-

tions.

5 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

1.2 Condition of guarantee

• The seller guarantees that the parts of the product are new, designed and manufactured so as to meet

the specific technical characteristics of the product itself.

• The guarantee period is 12 months (twelve months) if the purchaser is a judicial entity (so-called “B to

B sale”, i.e. “business to business”) or 24 months (twenty-four months) if the purchaser is a consumer

(so-called “B to C sale” ). The guarantee takes effect starting from the date of delivery of the product

and, more specifically, from the date of the signature of the test certificate, if the machine has been

tested, or from the date of the shipping document, in all other cases. In “B to B” sales, the guarantee

period may not in any case exceed 18 months from the date the machinery is shipped.

• At the moment of delivery, the purchaser is required to check that the machine is in good condition and

complete with all its parts.

• If the product has damage or defects which occurred during the guarantee period, the purchaser is

required to inform the seller, in writing, of the existence and the extent of said damage or defects no

later than 5 (five) days form the moment they are discovered, in “B to B” sales.

• The guarantee provides exclusively the right to free replacement or repair of the defective parts, which

will be considered as such after careful examination by the seller’s technical department. Shipping costs

shall be at the expense of the seller, who shall select the method of shipment based on his own

unquestionable judgment.

• Replacement or repair of parts covered by the guarantee shall not in any case extend the terms

thereof.

• Under no circumstances shall the purchaser be entitled to the repair of the machinery or of the single

components if full payment of the agreed amount has not been made.

1.2.1 Voidance of the guarantie

• This guarantee shall automatically be voided if the product undergoes interventions, modifications, or is

used by technicians or staff who are not authorized in writing by the seller.

• This guarantee does not cover the replacement of the parts that are subject to normal wear and spare

parts. Any additional costs, such as travel expenses, shipping and/or labour costs, are not covered by

said guarantee.

• The guarantee shall not in any circumstance include loss of profits or any direct or indirect consequence

thereof.

• The guarantee is automatically voided (in addition to the provisions in the supply contract) if:

a) non-original spare parts are used;

b) the damage is attributable to an erroneous operation performed by the purchaser and/or his per-

sonnel;

c) the damage is caused by insufficient maintenance;

d) the user carries out repairs at his discretion without the consensus of the manufacturer;

e) the instructions included in this manual are not carried out;

f) exceptional event;

also

g) THE REMOVAL OF THE SAFETY DEVICES WITH WHICH THE MACHINE IS EQUIPPED WILL

AUTOMATICALLY VOID THE GUARANTEE AND RELIEVE THE MANUFACTURER OR ANY LIABIL-

ITY.

The retailer shall not be liable for damage due to negligence, carelessness, poor utilization and improper use

of the machine and all of its parts that are subject to normal wear during operation, lack of skill and care-

6 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

lessness of the purchaser or his employees and/or of the final client/user and/or his employees, to unac-

ceptable overloads, to inadequate means and/or operating materials, to defects of the foundations and

structures of the building (if the machinery requires certain characteristics of the place in which the it is to

be located and installed, to inadequate means and/or materials of operation and to any other activity which

is extraneous or not compliant with normal use of the product or to its specific technical characteristics or

damage caused by modifications and/or repairs, replacements of single components, maintenance carried

out by personnel not authorized in writing by the seller or any circumstance independent of the seller, as

well as negligence or lack of skill in assembly by the purchaser and/or the final client/user.

1.3 Customer service

DANGER

PERFORMING REPAIRS, WORK OR CHANGES OF ANY KIND OTHER THAN THOSE INDICATED

HEREIN IS STRICTLY PROHIBITED.

Requests for servicing must be forwarded straight to the Technical Servicing Centre authorized by AGREX

SPA, which will send skilled personnel and provide any necessary information and explanationùs.

When applying, remember to quote:

• Machine type

• Serial number and year of manufacture

• Type of problem encountered

7 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

2 SECTION – General features

2.1 Machine markings

Each machine features an identification plate (Pic. 1), whose data are given below:

- (A) MANUFACTURER

- (B) ABSORBED POWER

- (C) MAXIMUM LOADING

- (D) WEIGHT WHEN EMPTY

- (E) MODEL

- (F) SERIAL NUMBER

- (G) YEAR OF MANUFACTURE

Picture 1

Removing, replacing or in any way altering the identification plates on the machine or any ac-

cessories it comes with is strictly prohibited.

The machine is supplied with:

- «Operation and maintenance manual»

- «Manufacturer’s declaration of conformity»

8 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

2.1.1 Spreader description

The spreader consists of:

1- Frame

2- Gear box

3- Hopper

4- Hydraulic control

The SDA series spreaders have been conceived to spread different types of fertilizers, as well as seeds, salt

and granulated materials in general.

It is strictly forbidden to spread iron pieces, stones, grivel, glass and similar materials as they

may injure people and cause damages.

• The fertilizer spreader is equipped with a regulation system that allows carrying out a spreading that

varies from 6 to 18 meters.

• The system that controls the fertilizer spreading is composed by an adjustable lock gate that assures the

best accuracy in the spreading and in the dosing also with superconcentrated products and seeds.

• Easy to charge: the models SDA 500 and , SDA 600 are 94 cm and 104 cm high respectively.

• Highest safety standards: all rotating and transmission parts are protected by guards and protection

devices in compliance with CE provisions.

• Simple design and functioning: : acting on the hydraulic control (or on the mechanical levers it is

possible to obtain three types of spreading: at 180 degrees, or at 90 degrees only on the right side or 90

degrees only on the left side.

A single worker can do himself all the necessary operations by himself

Picture 2

9 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

2.1.2 Scheduled use

The machine has been built in conformity with European Union standards given in directive 2006/42/EC as

described in the manufacturer’s declaration supplied with each machine.

The machine is designed to be used ideally for sowing and fertilising of gardens, sports fields and small

green areas.

The following can be spread:

- solid mineral fertilisers in granular or powder form

- seeds

- salt and sand

The machine should be carried and driven by tractors or self-propelled machines with a power suitable to

the spreader weight when it is completely full.

The machine must be operated only outdoors and when visibility is sufficient to see where the product is be-

ing spread.

The machine is designed for professional use and the operators in charge must be certified fit and be able to

read and understand the contents of this manual.

Operators must also use the machine in compliance with the current regulations concerning safety, condi-

tions for use and characteristics of the machine.

2.1.3 Non-scheduled use

NEVER spread materials not specified in this manual: this would affect the safety of the machine users and

persons working nearby.

NEVER disable the machine safety devices or remove the danger notices.

NEVER allow the machine to be used by disabled persons or children.

DO NOT transport people or animals during work and when moving the machinery from one place to an-

other.

Consequently, the manufacturer shall NOT BE held responsible for any damage to equipment or

property or bodily injury as a result of its improper use or any use other than that for which the

machine is intended.

2.2 Control devices

In order to open and close the hopper discharging gates, it is necessary to act on the OPEN and CLOSE me-

chanical levers which are positioned on the spreader front (or, on the model with hydraulic system, operate

on the OPEN CLOSE tractor hydraulic circuit)

Moreover, for the spreading regulation the machine is complete of:

- Product quantity regulation levers: positioned on the rear of the spreader. The product quantity

setting is facilitated by the graduated scale. By moving the gate towards the higher values the quantity

of product flow increases, vice-versa, by moving the gate towards the lower values the quantity of prod-

uct flow decreases.

- Adjustable spreading vanes: they are positioned on the spreading discs and allow to adjust the width

and the spreading uniformity.

10 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

2.3 Technical data

Model SDA 500 SDA 600

Capacity (l) 500 600

Maximun loading (kg) 800 800

Weight when empty (kg) 154 163

Spreading width (m) 6 – 18 6 – 18

A Lenght (cm) 112 112

B Width (cm) 110 110

C Height (cm) 94 104

Tractor power required (HP) 50 – 80 50 – 80

Chart 1

Max P.T.O. speed: 540 rpm

Picture 3

2.4 Standards applied

The machine has been designed and produced in conformity with the provisions of directive 98/37/EC,

namely all moving parts have been made harmless by using guards, barriers and safety systems.

The machine has also been designed to the following directives and standards:

EN 14017:2005 +A2:2009 Agricultural and forestry machinery – Solid fertilizer distributors – Safety (2005)

EN ISO 4254-1:2009 Agricultural machinery -- Safety -- Part 1: General requirements

ISO 11684:1995 Tractors, machinery for agriculture and forestry, powered lawn and garden

equipment - Safety signs and hazard pictorials - General principles. (1995)

11 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

3 SECTION – Safety and accident prevention

3.1 Safety

The user must instruct personnel as to risks deriving from accidents, devices installed for the purpose of op-

erator safety, and general safety rules provided for by directives and legislation in the country where the

machine is being used.

Operator safety is one of the primary concerns of any machine manufacturer. When producing a new ma-

chine, every effort is made to allow for all potential hazardous situations and, of course, to adopt appropri-

ate safety devices.

Nonetheless, the level of accidents caused by careless and inexpert use of various machines is still very high.

Lack of attention, thoughtlessness and overconfidence often lead to accidents, as can fatigue and drowsi-

ness.

Hence this manual must be read very carefully, concentrating in particular on the section on safety rules.

WARNING

The Manufacturer declines all responsibility for failure to comply with safety and accident-

prevention regulations provided for by legislation, and with the provisions herein

DANGER

WATCH OUT FOR THIS SYMBOL IN THE MANUAL: IT INDICATES A HAZARDOUS SITUATION.

Depending on the danger involved, this symbol may have one of three meanings:

DANGER

The “DANGER” label indicates the highest level of danger and is intended to warn you that if the operations

described are not performed properly, they will result in serious injury, death or long-term health risks.

WARNING

The “WARNING” label warns you that if the operations described are not performed properly, they may

result in serious injury, death or long-term health risks.

CAUTION

The “CAUTION” label warns you that if the operations described are not performed properly, they may re-

sult in damage to the machine and/or injury.

12 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

IN ACCORDANCE WITH OF THE DIRECTIVE 98/37/CE NOTE THE FOLLOWING CONVENTIONS:

DANGER ZONE: Any area inside and/or near a machine that potentially compromises the safety or health

of any exposed person there.

EXPOSED PERSON: Any person with all or part of his/her body inside a danger zone

OPERATOR: The person(s) in charge of installing, running, adjusting, servicing, cleaning, repairing and

transporting a machine.

3.1.1 General safety rules

DANGER

Failure to comply with the provisions of “Section 3 - Safety and accident prevention” and any tamper-

ing with safety devices shall relieve the Manufacturer of any responsibility in case of accident, damage or

malfunctioning of the machine.

GENERAL WARNINGS:

• The user undertakes to entrust the machine only to qualified and suitably trained personnel.

• The user is required to take all necessary measures to ensure that unauthorized personnel have not access

to the machine.

• The user undertakes to suitably instruct his personnel on the application and observance of safety rules.

For this reason, he undertakes to ensure that all persons receive directions for using the machine and safety

rules appropriate to their tasks.

• The user must contact the Manufacturer to report any defects or malfunctions detected in safety systems,

as well as any situation presumed to be dangerous.

• The user at all times, must use personal protective gear provided for by legislation, and follow the instruc-

tions herein.

• The user must comply with all safety symbols and warnings applied on the machine.

• The user must not take their own initiative to perform operations or work outside their area of compe-

tence.

• The user are required to report to their superior any problems or hazardous situation encountered to their

superiors.

• The machine has been tested only with the equipment supplied only. Fitting parts of different makes or

making changes may alter the machine’s characteristics and hence compromise its safe operation. Conse-

quently, the Manufacturer declines any responsibility for any damage that might derive from use of non-

original parts.

13 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

• The machine must be used only for the purpose for which it has been designed alone.

• The machine must not be run with safety devices removed.

3.1.2 Safety signs

The machine has been produced adopting every possible safety standard to assure operator safety.

Nonetheless, the machine may present further residual hazards that cannot be eliminated altogether under

certain conditions of use.

The safety symbols (pictograms) applied on various points of the plant are intended to draw the user’s at-

tention and warn him/her of danger: consequently, it is necessary to know the meaning of said symbols and

to memory them. Any symbols that have been damaged, misplaced or belong to parts that have been

changed must be replaced with other original symbols, requesting them to from the Manufacturer, and must

be applied in exactly the same place.

DANGER

KEEP ADHESIVES CLEAN, AND REPLACE THEM AS SOON AS THEY START PEELING OFF OR ARE

DAMAGED.

Referring to figure read the following descriptions carefully, committing their meanings to memory.

Picture 4

14 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

1. Warning! Risk of crushing; do not stand between the machine and the tractor.

2. Warning! Risk of injury by pressurised liquids; read the Operation and Maintenance Manual before

proceeding to operations on the machine.

3. Warning! Read the Operation and Maintenance Manual carefully.

4. Warning! Before performing any maintenance operations, remove the tractor’s ignition key and read

the Operation and Maintenance Manual.

5. Always wear a work suit, safety gloves and safety shoes. Always wear safety goggles during ma-

chine loading and maintenance operations.

6. Warning! Distribution parts in movement; never enter the hopper while the machine is running.

7. Warning! Keep a safe distance from the machine; risk of sprayed product.

8. Warning! Risk of falling, do not mount the machine for purposes of transportation.

9. This indicates the coupling point to be used for machine lifting.

10. Warning! Never exceed a value of 540 rpm in the power takeoff.

15 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

3.2 Safety devices

The machine features GUARDS: Stationary devices that prevent direct contact with moving parts or any

other hazardous part of the machine. Said guards can be removed only with the aid of special tools. When

the machine is operating, said devices must be fitted correctly.

CONSEQUENTLY, THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR ANY DAMAGE RE-

SULTING FROM TAMPERING WITH GUARDS AND SAFETY DEVICES.

3.3 Noise hazard

Sound level (airborne noise) measured from one metre away with the machine running was as follows:

Sound pressure at the operator’s position measured according to EN ISO 4254-1:2009 Standard - Appendix

LpA = 84.7 dB(A)

3.4 Dust hazard

WARNING

When spreading powder fertilisers, dust can form in the air especially when it is windy. You are

therefore advised to wear a mask to protect the respiratory system.

Fertilisers in general can irritate the skin and eyes: contact the supplier for information on the personal pro-

tection measures to be adopted.

3.5 Clothing

WARNING

Wear suitable clothing. Avoid baggy, loose-fitting clothing: It might get caught up in moving parts. Long hair

should be tied back. Operators should not carry scissors or sharp tools in their pockets.

During maintenance and repair work, workers are required to wear protective clothing, cut-proof gloves, and

non-slip boots with reinforced

3.6 Ecology and pollution

WARNING

• Comply with laws in force in the country where the machine is being used regarding use and disposal of

products employed in cleaning and servicing the machine, and comply with the instructions issued by the

manufacturers of said products.

16 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

• Dispose of any special waste by handing waste materials in to suitably authorized firms, and demand a re-

ceipt attesting the disposal.

• Dispose of any packaging left over from the machine’s transport in conformity with the regulations in force.

• If the machine is to be dismantled, comply with the pollution-prevention regulations provided for by the

country it is used in, exercising particular care when it comes to lubricants and electric components.

• Collect all spent products from the hydraulic circuits in appropriate containers. Deliver all spent oil recov-

ered to authorised collection centres (spent oil consortiums).

3.7 Safe use

WARNING

Safety standards: HOW TO AVOID ACCIDENTS

• To avoid accidents, pay close attention to the warning notices affixed on the machine and

read this guide carefully.

• The use of the spreader is restricted to the fuctions, for which it has been designed and which

are described in the present guide. The manufacturer will not be held responsible for any dam-

ages to things or injuries to people caused by a wrong use of the spreader.

• Before starting the spreader, make sure all protection devices and guards are mounted correctly.

• Make sure no bystanders (especially children) or animals are in the working area. This is extremely impor-

tant when the spreader is being used near pubblic or easily accessible roads.

• Minors (under 18) are not allowed to operate the spreader.

• The spreader can be used with every kind of tractor of suitable power, whose couplings are compatible

with those of the spreader and which is equipped with all P.T.O. and cardan shaft protection devices.

• Before connecting the P.T.O., make sure the revolution number of the tractor corresponds to that of the

spreader. In any case,

never exceed 540 rpm.

• It is strictly forbidden to spread iron pieces, stones, grivel, glass and similar materials as they may injure

people and cause damages to things.

• Never load the hopper with wet products as they may obstruct the outlets.

• During work, wear close-fitting and laced-up garments, heavy safety shoes, and safety gloves and mask

especially while spreading powdery fertilizers in windy weather.

• After using the spreader, turn the engine off, apply the handbrake, lower the spreader to the ground, dis-

engage the P.T.O. and, if the hopper is still partially full, even the product up in order to avoid accidental

tippings.

• Do not carry out any maintenance or cleaning operation while the spreader is connected to the 3-point

hitch of the tractor.

• It is strictly forbidden to transport persons while the spreader is in operation or during transfers.

• During transfers, make sure the P.T.O. is disengaged.

17 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

• When travelling on public roads, connect the spreader to the tractor as described on the present guide. A

wrong connection may alter the vehicle stability. It is necessary to abide by the national traffic code.

• We remind you that a careful operator is the best insurance against accidents.

• The area the machine is used in should be considered a «DANGER ZONE», especially for anybody not

trained in its use.

• Be careful of people and animals in the machine operating range: this is important when working on land

or roads open to the public.

• When people are «exposed», i.e. are in the «DANGER ZONE», the operator must stop the machine in-

stantly, and possibly have the person removed.

• Whilst the machine is operating, operators must be in a position where they have full control of the ma-

chine so that they can take immediate action at any time and in any event.

• Check periodically the machine as a whole, and its safety devices, at regular intervals to ensure they are

intact.

• If safety guards are removed, make sure they are refitted properly before using the machine again..

• Maintenance or repair work must be performed by personnel qualified for the specific tasks.

• At the end of maintenance and repair work, before re-using the machine the technical manager must en-

sure that the work has been completed and that the protections have been re-fitted.

• Transport of persons or animals during work and when moving the machine from one place to another is

strictly forbidden.

• Regularly check the condition of the protections for the cardan shaft, bearing in mind that only cardan

shafts with protections in good condition must be used.

• Never enter the hopper with the fertilizer spreading devices in motion.

• In order to avoid the formation of lumps of fertilizer and the clogging of the hopper, do not spread fertil-

izer on extremely humid or rainy days (if necessary, use the hopper-cover tarpaulin provided as an optional).

Whenever clogging occurs, immediately switch off the machine to avoid damaging the fertilizer spreading

devices. Remove lumps of fertilizer only after first switching off the tractor. Wear personal protective equip-

ment (safety gloves, goggles) during machine cleaning operations.

• Use cranes with adequate load capacity to load fertilizer sacks weighing more then 30 kg.

18 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

4 SECTION - Handling and installation

CAUTION

The fertiliser spreader and accessories are generally partially fitted at the factory and shipped in cardboard

packaging or on pallet. To complete assembly, follow the instructions given in this manual.

In some cases, depending on customer requirements, the machine is delivered fully assembled.

Upon receipt of the goods, carefully check to ensure that no damage has occurred during transport.

4.1.1 Assembly of hopper extensions

WARNING

Before proceeding to hopper extension assembly/disassembly, uncouple the fertilizer spreader

from the tractor and make sure that the fertilizer spreader is parked on solid, level ground.

Wear safety gloves and safety shoes for all the operations below.

Proceed as follows to assemble hopper extensions:

1. Fasten the longer lifting panel to the front

part of the fertilizer spreader. Do not tighten

the fixing screws all the way at this point.

2. Fasten the two lateral panels

3. Fasten the rear lifting panel.

4. Tighten all screws in order to solidly connect

the hopper extension to the standard hopper.

19 di 64

SDA 500 – SDA 600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

4.2 Handling

Use only appropriate fork-lifts with adequate capacity for the handling of the material.

Lift the machine using the indicated lifting points (see picture 5).

ATTENZIONE

Lift the machine only when the hopper is empty.

Picture 5

Nel caso la macchina non venisse immediatamente montata, ma si rendesse necessario uno stoccaggio tem-

poraneo, dev’essere posta in un ambiente asciutto e al coperto.

Per proteggere le varie parti dagli agenti atmosferici si consiglia di lasciare integri gli imballaggi.

4.3 Hitching

WARNING

The spreader can be hitched to any tractor of suitable power (see technical specifications).

Before hitching the spreader to the tractor, apply the handbrake and make sure the P.T.O. is disengaged.

Wear safety gloves.

20 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

Picture 6

Apply the minimum front ballast to the tractor (see Appendix A).

Fix de lower bars of the tractor lifting machanism to the lower couplings of the spreader (Pic. 6) and then

secure with safety pins.

Connect the upper bar of the 3-point hitch with the suitable pin and safety split pin.

To increase the machine firmness, fasten the lower bars of the 3-point hitch with the suitable tie-rods.

Place the drive-shaft, making sure the backstop has been relased at the power takeoff and that the screw

on the drive-shaft of the fertilizer spreader is locked. Read the handbook of the drive-shaft

Lift the spreader from the ground using the tracctor liftiing bars. Release the two support feet B by un-

screwing the respective locking handwheels A.

When the P.T.O. shaft is a maximun exstention, the two inner tubes have to overlap at least 15-20 cm.

When the P.T.O. shaft is completly closed, there must be a gap of at least 4-5 cm to avoid collisions with the

outer side (Pic. 7).

The working angle of the P.T.O. has to be the smallest possible; preferably it should not exceed 10° (Pic. 8),

so has to make the P.T.O. shaft and the machine last longer.

Picture 7 Picture 8

1° - 2°

3°

21 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

–

Adjust the 3-point lifting mechanism of the tractor so that the working position of the spreader i horizon-

tal (70-80 cm above the ground) see (Pic. 9).

Picture 9

–

Connect the hoses of the double-acting hydraulic couplings of the tractor (Pic. 9). In this way the shut-

ters can be easily controlled from the driver’s seat. Another aspect that the flow regulation on the hydraulic

cylinder offers is that one varies the lever opening and closing speed.

Before connecting yhe hidraulic hoses or carry out any mantenance work on the hydraulic system, lower the

spreader to the ground, tur the engine off and drop the pressure.

4.4 Preliminary cleaning

Once all connections have been made, the whole machine must be cleaned of dirt that has built up during

transit, storage and handling.

Use suitable non-corrosive degreasing products and dry all machine parts - exposed metal and paintwork

alike - using soft, dry cloths.

4.5 General inspection

WARNING

Before starting to use the machine, safety devices must be checked to ensure they are efficient and working

perfectly.

To work in complete safety it is necessary to:

• Tighten the bolts and all locking devices.

• Make sure all safety guards are properly installed.

• Do not leave tools or other objects not belonging to the machine inside the hopper or on the mechanical

parts.

22 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

5 SECTION – Use

5.1 Prior to use

Before operating the machine, the operator must have read and understood all parts of this manual, espe-

cially those given in “Section 3” on Safety.

Check the machine’s conditions carefully, especially parts most subject to wear and tear.

5.2 Starting up

The machine must be operated exclusively by skilled personnel, who have been properly trained in the use

of the machine and in the main safety procedures. Before starting the machine, personnel are required to

make themselves familiar with its controls.

5.3 Adjustments

Warning

In order to avoid accidents and dangerous situations every machine adjustments has to be

done exclusively with the machine switched off and the ignition keys have to be disconnected.

The adjustment should be done accordingly to this use and maintenance manual

The machine control is described in 2.2 Control Devices.

5.3.1 Product spreading adjustment

1- Release the regulation lever by unscrewing the ball crank handle (A)

2- Move the index to the desired position. By moving the index towards the higher values the fertilizer

quantity increases, while moving the index towards the lower values the quantity of fertilizer decreases

to a complete closing of distribution. The regulation must be done for both left and right sides.

3- Block the regulation lever by screwing the ball crank handle (A).

Picture 10

23 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

5.3.2 Spreading width adjustment

In order to get an even spreading on both left and right sides, according to the different specific weights

of the fertilizers, it is possible to change the position of the vanes by fixing them in the stops 1-2-3-4-5.

Picture 11

1. Unscrew the paddles screw. 2. Move the paddles to the new position.

To adjust the spreading width and the spreading uniformity refer to the adjustment table and act on (see

picture 12):

1. Short spreading vane: (C): by increasing the opening angle the fertilizer quantity increases to the

centre of the spreading (first 6-7 meters) and by decreasing the opening angle the concentra-

tion of fertilizer decreases

2. Long spreading vane: (D): by increasing the opening angle the fertilizer quantity increases on the

medium distance fertilizing area (8-10 meters) while by decreasing the opening angle the con-

centration of fertilizer increases on the spreading area extremity (more than 10 meters).

Picture 12

24 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

5.3.3 Spreading patterns

It is possible to obtain three different spreading patterns by operating on the levers (or on the hydraulic ac-

tuator if present) (fig. 13 e fig. 14).

- 180 ° spreading width : Levers (F) and (E) open.

- 90° right spreading width: lever (E) closed, lever (F) open.

- 90° left spreading width : lever (E) open, lever (F) closed.

Picture 13 Picture 14

To enable the regulation levers to work independently it is necessary to act on the locking lever which

keeps them together:

1. Lever positioned on right side – left side

spreading hooked. 2. Lever positioned on right side – left side

spreading released.

For the distributors with the OPEN – CLOSE hydraulic system, the patterns of spreading can be obtained by

operating on the OPEN – CLOSE control of the hydraulic distributor of the tractor.

E F

25 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

5.3.4 Loading the machine's hopper

It is very important to check the stability of the fertilizer spreader after coupling to the tractor.

• Before loading the fertilizer spreader, follow the instructions provided in Appendix A to this manual in

order to calculate the minimum front ballast to be applied to the tractor required to ensure the stability

necessary after the tractor and fertilizer spreader have been coupled together.

• Lower the fertilizer spreader into loading position (until it touches the ground), switch off the tractor's

engine, and set the parking brake in order to prevent any and all accidental movement.

• Fill the hopper to the required level, making sure to distribute the fertilizer homogeneously inside to a

flat level on top.

• Never load the hopper above its maximum acceptable loading level – See Table 1 Technical

Data.

Remember that the product to be spread must be clean, and that stones and scraps of metal can both cre-

ate risk and irreparably damage the machine's moving parts.

5.3.5 Distribution

- Operate the tractor power take off.

- Set the tractor hydraulic system control in order to open (and close) the batching selvage.

Thanks to the stirrer moving, the product goes onto the spreading disc and, because of a centrifugal force, it

will be cast outward by the spreading vanes.

5.3.6 Driving technique suggestions

The quality of spreading depends greatly on the operator's driving technique.

• During fertilizer spreading, maintain the speed indicated in the spreading tables as constantly as possi-

ble. Spreading the fertilizer at insufficient speed increases the concentration of the fertilizer spread on

the soil, whereas excessive speed decreases such concentration.

• During spreading, adopt evenly-distanced spreading passages in order to maintain constant distance

from all previous spreading passages.

• Stop spreading in the vicinity of the ends of the drills and during manoeuvres. In order to avoid spread-

ing fertilizer outside the edges of the field, switch spreading back on again only after approaching the

end of the field at a distance equal to the maximum rear spreading length (see the spreading tables).

• Grains of fertilizer are very lightweight and their trajectory of movement varies with the amount of wind.

For this reason, stop spreading when wind speed is too high, otherwise the distribution of the fertilizer

spread over the soil will be irregular.

5.3.7 Late top-spreading

For late top-spreading it is necessary to tilt the spreader.

1. To set the spreader tilt, set the length of the 3-point hitch.

26 di 64

XPL AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

5.3.8 Side spreading conveyor (optional)

The side spreading conveyor allows for localized spreading on row cultivation of 1.5 – 5 meters.

To adjust the spreading width of the deflector it is necessary to:

1. Unscrew the ball crank handle (G

2. Position the deflector in the desired position

3. Screw the ball crank handle for blocking (G)

This operation must be done on both sides.

27 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

6 SECTION – Maintenance

6.1 Routine maintenance

DANGER

BEFORE CARRYING OUT ANY MAINTENANCE WORK ON THE MACHINE, DETACH THE TOWING

VEHICLE AND DISENGAGE THE SPREADER DISC TRANSMISSION BY MEANS OF THE LEVER

PROVIDED.

ALWAYS SWITCH OFF THE TRACTOR’S ENGINE BEFORE PROCEEDING TO MAINTENANCE.

The various maintenance operations are described below.

The time intervals given refer to normal operating conditions; consequently, if the machine is

subjected to particularly heavy duty, they must be reduced accordingly.

The purpose of these instructions is to assure efficiency, reduce wear and generally make the machine last

longer: the user has everything to gain from keeping the machine in pristine condition.

6.1.1 Daily cleaning

After each day’s work, the machine must be cleaned thoroughly, removing any waste and/or residues left

behind after processing, or other damp or dusty materials.

6.1.2 General checks

The vibrations produced during work and movement of the equipment from one place to another may in the

long term cause loosening of the bolts. You are advised to check the nuts and bolts roughly every 50 work-

ing hours.

Grease the PTO shaft cross every 10 hours and check the tension of the belts that drive the spreading discs.

The lubrication of the transmission group must be checked every 200 hours.

6.1.4 Spreading paddle assembly/disassembly

WARNING

Before proceeding to the assembly/disassembly of the fertilizer spreader paddles, switch off

the tractor’s engine and set the parking brake.

1. Loosen the screws that fasten the spreader paddle to the fertilizer spreader disk.

2. Replace the old fertilizer spreader paddles with new ones and re-tighten the fixing screws.

Warning! The fertilizer spreader’s paddles must be assembled in the correct disk rotation direction.

28 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

Correctly assembled paddles Incorrectly assembled paddles

6.2 Extra maintenance

It is essential to conduct a general inspection of the machine’s mechanical parts at regular intervals.

In particular, it is necessary to check the usury of the vanes.

6.3 To keep in mothball

PARK THE FERTILIZER SPREADER ONLY WITH THE HOPPER EMPTY AND ONLY ON SOLID,

LEVEL GROUND.

If the machine is not employed for a long time it is necessary to check its mechanical and electrical parts, so

that to avoid problems when bringing it into use again.

All parts subjected to wear must be carefully controlled. The worn out and damaged parts should be imme-

diately replaced by original spare parts provided by the distributor or the producer.

Besides, check that the bolts of the machine are not shaked loose during the working.

Such instructions are meant to maintain the machine in good conditions, riducing its wear and tear and pro-

longing its life.

Uncouple the fertilizer spreader from the tractor by undoing the operations indicated in Section 4.2 (Cou-

pling to the tractor).

After the fertilizer spreader has been uncoupled, couple the cardan shaft to the respective support (see the

respective figure) in order to avoid damaging the protections provided for the cardan shaft itself.

For the models with the hydraulic system, hook the hydraulic distributor to its support. (see the picture).

29 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

6.4 Re-start

WARNING

Before putting the machine back into service, it is always a good idea to check its general conditions: its cur-

rent state will depend on the conditions it was mothballed in.

6.5 Dismantling the machine

Should the decision be made to dismantle the machine, its components must be sorted into groups of like

materials and disposed of individually in accordance with the local laws in force on disposal of special waste.

WARNING

WHEN DISPOSING OF THE VARIOUS COMPONENTS, ONLY GO THROUGH A LEGALLY AUTHOR-

IZED FIRM THAT WILL ISSUE A RECEIPT ATTESTING TO DISPOSAL.

30 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

7 SECTION – Spare parts

7.1 Spare parts

All the spare parts can be ordered from the manufacturer, quoting:

- machine model

- machine’s serial number

- year of manufacture

- reference code of the part (to be found in the spare parts catalogue);

- means of transport: if no preference is specified, the manufacturer shall do its best to ensure you re-

ceive good service, though it declines all responsibility for any delays in shipment as a result of force ma-

jeure.

Lastly, remember you can always contact the manufacturer for your servicing.

31 di 64

32 di 64

SDA

500/600/

SDA

500/600

Istruzioni originali • Translation of the original instructions

CATALOGO RICAMBI

ATTENZIONE! Per un corretto funzionamento delle nostre

macchine usare esclusivamente RICAMBI ORIGINALI

SPARE PARTS

WARNING! Use ORIGINAL PARTS to ensure the correct

functioning of the machine

Italiano

English

Istruzioni originali • Translation of the original instructions

Italiano

English

Cod. RCenSDA56R02 - 02.2014

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDA500BASE10R0 Tab.1/2

TELAIO

1415

14 15

1424

15 14

14 24

28 27

30 15

815

15 14

SDA 500

SDA 600

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

FRAME

34 di 64

Code: SDA500BASE10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 SDA05000 1 TELAIO SPANDICONCIME SDA FRAME MOD. SDA

2 SDA06400 1 SOSTEGNO CENTRALE SUPPORT

3 PTOCUFFIA 1 CONTROCUFFIA P.T.O PTO GUARD

4 C2200000 1 ALBERO CARDANO 12X900 - NORME CE PTO SHAFT 12X900 - EC STANDARD

5 SDA07800 2 PROTEZIONE DISCHI DOSING DISC PROTECTION

6 TCPP3200 4 TAPPO A PUNTALE NERO Ø=32 PLUG Ø=32

7 SDA05300 1 CARTER SDA GUARD

8 SDA08100 1 DIVISORIO TRAMOGGIA SDA PARTITION PANEL

9 SDA07700 2 GRIGLIA SDA GRID

10 40015026 8 BLOCCHETTO FERMARETE FILO D.5 MM MESH CLAMP

11 SDA09200 2 AGITATORE SDA AGITATOR

12 57390820I 2 VITE INOX TEIF M8X20 UNI 5739 SCREW TEIF M8X20 (STAINLESS STEEL)

13 57320840I 8 VITE INOX T-TONDA M8X40 BOLT TBQST M8X45 INOX

14 659208IN 36 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

15 747408IN 24 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

16 57390825I 2 VITE INOX TEIF M8X25 UNI 5739 SCREW M8X25 STAINLESS STEEL

17 57370855I 2 VITE TEPF 8.8 M8X55 INOX SCREW TEPF 8.8 M8X55 (S.S.)

18 57391035I 8 VITE INOX TEIF M10X35 UNI 5739 SCREW TEIF M10X35 (STAINLESS STEEL)

19 659210IN 16 RONDELLA INOX PIANA M10 PLAIN WASHER M10 (STAINLESS STEEL)

20 747410IN 8 DADO INOX AUTOBLOCCANTE MEDIO M10 NUT SELF-LOCKING M10 (STAINLESS STEEL)

21 57391235I 4 VITE INOX TEIF M12X35 SCREW TEIF M12X35 (S.S.)

22 659212IN 8 RONDELLA INOX PIANA M12 PLAIN WASHER M12 (STAINLESS STEEL)

23 747412IN 4 DADO INOX AUTOBL. MEDIO M12 SELF-LOCKING NUT M12 (S.S.)

24 54390825 10 VITE INOX TEIF M8X25 UNI 5739 SCREW TEIF M8X25 (S.S.) UNI 5739

25 SDA12000M 1 KIT BOCCHETTA SCARICO RAPIDO DESCHARGE TUBE

26 57390620I 2 VITE INOX TEIF M6X20 SCREW TEIF M6X20 (S.S.)

27 659206ZN 2 RONDELLA PIANA ZN M6 GALVANIZED PLAIN WASHER M6

28 558806IN 1 DADO INOX ES.MEDIO M6 NUT M6 (STAINLESS STEEL)

29 57370850I 1 VITE INOX TEPF M8X50 UNI 5737 SCREW TEPF M8×50 (STAINLESS STEEL)

30 SDA12005 1 BUSSOLA COLLEGAMENTO GRUPPO-AGITATORE CONNECTING BUSH

35 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDA500TRAM10R0 Tab.1/2

TRAMOGGIA DI CARICO

SDA 500

SDA 600

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

LOADING HOPPER

36 di 64

Code: SDA500TRAM10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 SDA05100 1 TRAMOGGIA 500 L. SDA HOPPER 500 L.

2 SDA09900A 2 RIALZO LATERALE SDA 600-1000-1200 HOPPER EXTENSION SDA 600-1000-1200

3 SDA09600 2 RIALZO ANT. POST. SDA 600 FRONT AND REAR EXTENSION

4 659208IN 18 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

5 747408IN 16 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

6 57320820I 14 VITE INOX T-TONDA M8X20 UNI 5732 SCREW M8X20 (STAINLESS STEEL)

7 57390820I 2 VITE INOX TEIF M8X20 UNI 5739 SCREW TEIF M8X20 (STAINLESS STEEL)

37 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDATRASMISSIONE10R2 Tab.1/2

GRUPPO DISTRIBUZIONE

13 23

11 22

SDA 500

SDA 600

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

DISTRIBUTION GROUP

38 di 64

Code: SDATRASMISSIONE10R2 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 SDA01600 1 ALETTA SINISTRA L.205 LEFT VANE L.205

2 SDA01400 1 ALETTA SINISTRA L.240 37° LEFT VANE L.240 37°

3 SDA01700 1 ALETTA DESTRA L.205 RIGHT VANE L.205

4 SDA01500 1 ALETTA DESTRA L.240 37° RIGHT VANE L.240 37°

5 081800 1 DISCO DISTRIBUZIONE SINISTRO LEFT SPREADING DISC

6 081700 1 DISCO DISTRIBUZIONE DESTRO RIGHT SPREADING DISC

7 SDA09100 2 MOZZO DISCHI DISCS HUB

8 08.06.00 2 GRUPPO TRASMISSIONE LATERALE SIDE GEAR-BOX

9 08.05.00.A 1 GRUPPO TRASMISSIONE CENTRALE CENTRAL GEAR-BOX

10 SDA10000 4 PIASTRINA UNIONE GRUPPI CONNECTION PLATE GROUPS

11 SDA10200 8 BUSSOLA L.40 BUSH L.40

12 SDA10300 4 BUSSOLA L.19 BUSH L.19

13 57320825I 4 VITE INOX T-TONDA M8X25 SCREW T M8X25 (STAINLESS STEEL)

14 57371050I 2 VITE INOX TEPF M10X50 UNI 5737 SCREW TEPF M10×50 (STAINLESS STEEL)

15 747408IN 20 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

16 659208IN 12 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

17 57371015I 8 VITE INOX TEPF M10X150 UNI 5737 SCREW TEIF M10X150 (S.S.) UNI 5737

18 57371014I 4 VITE INOX TEPF M10X140 UNI 5737 SCREW TEPF M10X140 STAINLESS STEEL

19 659210IN 24 RONDELLA INOX PIANA M10 PLAIN WASHER M10 (STAINLESS STEEL)

21 747410IN 12 DADO INOX AUTOBLOCCANTE MEDIO M10 NUT SELF-LOCKING M10 (STAINLESS STEEL)

22 57390850I 6 VITE INOX TEIF M8X50 UNI5739 SCREW TEIF M8X50 (STAINLESS STEEL)

23 57330816I 4 VITE INOX T-TONDA M8X16 SCREW T M8X16 (STAINLESS STEEL)

24 659310IN 3 RONDELLA INOX CARR. M10X30 WASHER M10X30 (STAINLESS STEEL)

25 659308IN 8 RONDELLA INOX CARR. M8X24 WASHER M8X24 (STAINLESS STEEL)

39 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDAREGOLAZIONI10R0 Tab.1/2

REGOLAZIONI

19 821

23 22 12

18 18

14 13

12 22 23

14 16

18 18

SDA 500

SDA 600

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

ADJUSTMENTS

40 di 64

Code: SDAREGOLAZIONI10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 IMGO1030 2 IMPUGNATURA GOMMA 10X30 RUBBER HANDLE 10X30

2 SDA06100A 1 LEVA DX APERTURA RIGHT LEVER OPENING

3 SDA06200A 1 LEVA SX APERTURA LEFT LEVER OPENING

4 68730418 1 SPINA ELASTICA D.4X18 SPINA ELASTICA D.4X18

5 SDA09300 1 LEVA BLOCCAGGIO LOCKING LEVER

6 30070010 1 MOLLA A COMPRESSIONEL=41.5 DM=12.5 COMPRESSION SPRING L=28

7 SDA09400 1 PERNO BLOCCAGGIO LEVE PIN LOCKING LEVERS

8 SDA07500 1 ARCHETTO SDA BOW

9 SDA06800 2 RONDELLA GUIDA LEVE WASHER GUIDE LEVER

10 SDA10500 1 DISTANZIALE LEVE SPACER

11 20931228T 6 MOLLA A TAZZA Ø=12,2/28X1,5 SPRING Ø=12,2/28X1,5 UNI 2093

12 33699000 2 SNODO IN ACCIAIO AS DIN 71802 M10 JOINT

13 08.40.00 1 PERNO 3° PUNTO Ø=25 3RD POINT PIN Ø=25

14 80201063 5 SPINA PER INTERNI Ø=10X63 PIN Ø=10X63

15 30028004 1 SUPPORTO ALBERO CARDANICO PTO SHAFT SUPPORT

16 30210004 2 PERNO DOPPIO CAT.1-2 FIXING PIN D.12 L.70

17 747412IN 2 DADO INOX AUTOBL. MEDIO M12 SELF-LOCKING NUT M12 (S.S.)

18 659212IN 5 RONDELLA INOX PIANA M12 PLAIN WASHER M12 (STAINLESS STEEL)

19 747408IN 2 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

20 659208IN 2 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

21 73800825 2 VITE TBEI M8X25 ZN SCREW TBEI M8X25 ZN

22 659210IN 2 RONDELLA INOX PIANA M10 PLAIN WASHER M10 (STAINLESS STEEL)

23 558810IN 2 DADO INOX ES. MEDIO PG M10 A2 NUT M10 A2 (STAINLESS STEEL)

24 57390620I 1 VITE INOX TEIF M6X20 SCREW TEIF M6X20 (S.S.)

25 VB500013 2 VOLANTINO A CROCE M8 HANDWHEEL M8

26 SDA09000 2 PARTICOLARE INDICATORE DI QUANTITA’ QUANTITY INDICATOR

27 SDA08900 2 INDICATORE DI QUANTITA’ QUANTITY INDICATOR

28 57320845I 2 VITE INOX T-TONDA M8X45 BOLT TBQST M8X45 INOX

29 57371250I 1 VITE INOX TEPF M12X50 UNI 5737 SCREW M12X50 UNI 5737

41 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDASERRANDE10R0 Tab.1/2

SERRANDE DI DOSATURA

115

214

313

18 18 9

10 10

26 26

11 11

12 12

16 16

18 18

19 19

19 23

27 27

SDA 500

SDA 600

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

DOSING SHUTTERS

42 di 64

Code: SDASERRANDE10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 SDA08600 1 BOCCHETTA DX USCITA CONCIME RIGHT OPENING

2 SDA10700 1 RIVESTIMENTO SERRANDA DX SDA RIGHT GATE COVERING

3 SDA05700 1 SERRANDA DX SDA RIGHT GATE

4 SDA10900 2 BARRA FILETTATA LEVA THREADED ROD

5 33699000 8 SNODO IN ACCIAIO AS DIN 71802 M10 JOINT

6 SDA08800 1 COPRI BOCCHETTA DX RIGHT OPENING COVER

7 SDA08700 1 COPRI BOCCHETTA SX LEFT OPENING COVER

8 SDA10100 2 ALETTA SCIVOLO FLAP

9 SDA11000 2 BARRA FILETTATA INDICATORE THREADED ROD

10 57320845I 2 VITE INOX T-TONDA M8X45 BOLT TBQST M8X45 INOX

11 SDA06600 2 DISTANZIALE LEVE SPACER

12 SDA06500 2 LEVA INDICATORE INDICATOR

13 SDA05600 1 SERRANDA SX SDA LEFT GATE

14 SDA10600 1 RIVESTIMENTO SERRANDA SX SDA LEFT GATE COVERING

15 SDA08500 1 BOCCHETTA SX USCITA CONCIME LEFT OPENING

16 57310830I 4 VITE INOX T-TONDA M8X30 ROUND HEAD SCREW M8X30

17 57320820 2 VITE T-TONDA M8X20 ZN ROUND HEAD SCREW M8X20 ZN

18 558810IN 8 DADO INOX ES. MEDIO PG M10 A2 NUT M10 A2 (STAINLESS STEEL)

19 659210IN 4 RONDELLA INOX PIANA M10 PLAIN WASHER M10 (STAINLESS STEEL)

20 SDA06700 4 RONDELLA GUIDA WASHER

21 659208IN 10 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

22 747408IN 8 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

23 52390635 2 VITE TEIF 8.8 ZN M6X35 SCREW M6X35 UNI 5739

24 659206IN 4 RONDELLA INOX PIANA M6 PLAIN WASHER M6 (STAINLESS STEEL)

25 747406IN 2 DADO INOX AUTOBL. MEDIO M6 SELF-LOCKING NUT M6-A2 INOX

26 73800620 2 VITE TBEI M6X20 ZN GALVANIZED SCREW TBEI M6X20 ZN

27 559006IN 2 DADO INOX ES. C/RON. ZIG. M6 NUT M6 (STAINLESS STEEL)

28 558910IN 8 DADO ESAGONALE BASSO PF M10 INOX DADO ESAGONALE BASSO PF M10 INOX

43 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDAIDRO10R0 Tab.1/2

COMANDO IDRAULICO (Opzionale)

SDA 500

SDA 600

1314

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

HYDRAULIC CONTROL (Optional)

44 di 64

Code: SDAIDRO10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 L083000B 2 CILINDRO TUFFANTE MOUNTING PISTON

2 33665000 2 FORCELLA PER TIRANTE M10X42 FORK FOR CONNECTING ROD M10X42

3 33691042 2 CLIP FERMO FORCELLA 10X42 CLIP 10X42

4 30070012 2 MOLLA A TRAZIONEL=133 DE=25.5 INOX 302 COMPRESSION SPRING L=133 DE=25.5

5 30013250 2 TUBO OLIO 1/4” L.1700 1/4”M 1/4”F OIL DUCT

6 30055112 2 NIPPLE OLIO M/M 1/4”-1/4” FORO 1 MM OIL NIPPLE M/M 1/4”-1/4”

7 659314R0 6 RONDELLA RAME 1/4”. COPPER WASHER 1/4”.

8 SDA05800 1 SOSTEGNO SX PISTONE IDRAULICO SUPPORT LEFT HYDRAULIC PISTON

9 57390825I 4 VITE INOX TEIF M8X25 UNI 5739 SCREW M8X25 STAINLESS STEEL

10 679808IN 8 RONDELLA INOX D.E.V. M8 WASHER D.E.V. M8 (STAINLESS STEEL)

11 747408IN 4 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

12 51371280 2 VITE TEPF 8.8 M12X80 SCREW TEPF 8.8 M12X80

13 659212ZN 4 RONDELLA PIANA ZN M12 GALVANIZED PLAIN WASHER M12

14 747312ZN 14 DADO AUTOBL. ALTO ZN M12 DIN 982 LOCKNUT ZN M12 DIN 982

15 105600 1 SOSTEGNO PRESE IDRAULICHE OIL TUBES SUPPORT

16 30015501 2 TAPPO PVC FEMMINA X INNESTO RAPIDO M 1/2 QUICK CONNECTION PLUG

17 30055007 2 INNESTO R/MASCHIO F1/2”. COUPLING F1/2”.

18 30015026 2 RONDELLA RAME Ø=1/2” COPPER WASHER Ø=1/2”

19 30055110 2 TAPPO RIDUZIONE M 1/2” F 1/4” FITTING M 1/2” F 1/4”

20 57390620I 2 VITE INOX TEIF M6X20 SCREW TEIF M6X20 (S.S.)

21 659206IN 2 RONDELLA INOX PIANA M6 PLAIN WASHER M6 (STAINLESS STEEL)

22 SDA05900 1 SOSTEGNO DX PISTONE IDRAULICO SUPPORT RIGHT HYDRAULIC PISTON

45 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDAIDRODOPPIO10R0 Tab.1/2

COMANDO IDRAULICO (Opzionale)

SDA 500

SDA 600

1314

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

HYDRAULIC CONTROL (Optional)

46 di 64

Code: SDAIDRODOPPIO10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 A016000001 2 PISTONE A DOPPIO EFFETTO SDA DOUBLE ACTING PISTON

2 33665000 2 FORCELLA PER TIRANTE M10X42 FORK FOR CONNECTING ROD M10X42

3 33691042 2 CLIP FERMO FORCELLA 10X42 CLIP 10X42

5 30013250 4 TUBO OLIO 1/4” L.1700 1/4”M 1/4”F OIL DUCT

6 30055112 4 NIPPLE OLIO M/M 1/4”-1/4” FORO 1 MM OIL NIPPLE M/M 1/4”-1/4”

7 659314R0 12 RONDELLA RAME 1/4”. COPPER WASHER 1/4”.

8 SDA05800 1 SOSTEGNO SX PISTONE IDRAULICO SUPPORT LEFT HYDRAULIC PISTON

9 57390825I 4 VITE INOX TEIF M8X25 UNI 5739 SCREW M8X25 STAINLESS STEEL

10 679808IN 8 RONDELLA INOX D.E.V. M8 WASHER D.E.V. M8 (STAINLESS STEEL)

11 747408IN 4 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

12 51371280 2 VITE TEPF 8.8 M12X80 SCREW TEPF 8.8 M12X80

13 659212ZN 4 RONDELLA PIANA ZN M12 GALVANIZED PLAIN WASHER M12

14 747312ZN 14 DADO AUTOBL. ALTO ZN M12 DIN 982 LOCKNUT ZN M12 DIN 982

15 105600 2 SOSTEGNO PRESE IDRAULICHE OIL TUBES SUPPORT

16 30015501 4 TAPPO PVC FEMMINA X INNESTO RAPIDO M 1/2 QUICK CONNECTION PLUG

17 30055007 4 INNESTO R/MASCHIO F1/2”. COUPLING F1/2”.

18 30015026 4 RONDELLA RAME Ø=1/2” COPPER WASHER Ø=1/2”

19 30055110 4 TAPPO RIDUZIONE M 1/2” F 1/4” FITTING M 1/2” F 1/4”

20 57390620I 4 VITE INOX TEIF M6X20 SCREW TEIF M6X20 (S.S.)

21 659206IN 4 RONDELLA INOX PIANA M6 PLAIN WASHER M6 (STAINLESS STEEL)

22 SDA05900 1 SOSTEGNO DX PISTONE IDRAULICO SUPPORT RIGHT HYDRAULIC PISTON

47 di 64

SDA500/600

Spandiconcime centrifugo doppio disco

Catalogo ricambi

Code: SDADEFLETTORE10R0 Tab.1/2

CONVOGLIATORE BILATERALE (Opzionale)

SDA 500

SDA 600

12 12

16 11

615

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

DOUBLE BANDING (Optional)

48 di 64

Code: SDADEFLETTORE10R0 Tab.2/2

Cod. RCenSDA56R02 - 02.2014 Cod. RCenSDA56R02 - 02.2014

REF. CODE Q.TY DESCRIZIONE DESCRIPTION

SDA500/600

Twin disc centrifugal spreader

Spare parts

1 SDA07000 1 CONVOGLIATORE SDA DOUBLE BANDING

2 SDA07100A 1 BOCCA SX CONVOGLIATORE LEFT BAFFLE

3 SDA07200A 1 BOCCA DX CONVOGLIATORE RIGHT BAFFLE

4 VB500013 2 VOLANTINO A CROCE M8 HANDWHEEL M8

5 SDA07300A 2 SOSTEGNO CONVOGLIATORE SUPPORT

6 57391030I 6 VITE INOX TEIF M10X30 UNI 5739 SCREW TEIF M10X30(STAINLESS STEEL)

7 659210IN 12 RONDELLA INOX PIANA M10 PLAIN WASHER M10 (STAINLESS STEEL)

8 52391225 4 VITE TEIF 8.8 ZN M12X25 SCREW TE 12X25 ZN

9 659212IN 8 RONDELLA INOX PIANA M12 PLAIN WASHER M12 (STAINLESS STEEL)

10 747412IN 4 DADO INOX AUTOBL. MEDIO M12 SELF-LOCKING NUT M12 (S.S.)

11 52390820I 4 VITE INOX TEIF M8X20 UNI 5739 SCREW TEIF M8X20 (S.S.) UNI 5739

12 659208IN 10 RONDELLA INOX PIANA M8 PLAIN WASHER M8 (STAINLESS STEEL)

13 747408IN 4 DADO INOX AUTOBLOCCANTE MEDIO M8 SELF-LOCKING NUT M8-A2 (STAINLESS STEEL)

14 57320816 2 VITE T-TONDA M8X16 ZN BOLT 8X16 ZN

15 747410IN 6 DADO INOX AUTOBLOCCANTE MEDIO M10 NUT SELF-LOCKING M10 (STAINLESS STEEL)

16 SDA07600A 1 BOCCA DX D.120 CONVOGLIATORE RIGHT BAFFLE D.120

17 SDA07600 1 BOCCA SX D.120 CONVOGLIATORE LEFT BAFFLE D.120

49 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

8 Annex A - Stability of the tractor distributor combination

As a conseguence of mass of the spreader itself and of the materials present in the hopper, the tractor dis-

tributor combination may become unstable. For verify the total stabiliti, the following expression can be ap-

plied for the calculation of the minimun ballisting at the front of IF,min which allows to have a weight on the

front axel equal to 20% of the unladen weight of the tractor:

TE [kg] Unladen weight of tractor ①

TF [kg] Front axle load of unladen tractor ①

TR [kg] Rear axel load of unladen tractor ①

IR [kg] Combinated weight of rear mounted implement/rear ballast ②

IF [kg] Combinated weight of front mounted implement/front ballast ②

a [m] Distance from centre of gravity for combined front mounted implement/front

ballastat to front axle centre ② ③

b [m] Tractor wheelbase ① ③

c [m] Distance from rear axle centre to centre of lower link balls ① ③

d [m] Distance from centre of lower link balls to centre of gravity for combined

rear mounted implement/rear ballast (0.585 m) ② ③

① see instruction handbook of the tractor

② see price list and/or instruction handbook of the implement

③ to be mesured

)(

)2,0()())((

min, ba

bTbTdcI

IEFR

F+

×+×−+×

50 di 64

SDA 500 – SDA600 AGREX S.p.A.

Fertilizer Spreader Via Balla, 55/57 – 35010 Villafranca Padovana (PD)

Tel. +39 049 9075684 – Fax +39 049 9075524

Spreading Tables

51 di 64

6810 6810 6810

AB AB AB

0,5 2,0 4 1 33 24 20 0,5 2,4 5 2 40 30 24 0,5 1,0 5 3 17 13 10

13,9 4 1 64 48 39 1 4,8 5 2 79 59 48 1 4,1 5 3 68 51 41

1,5 8,4 4 1 139 104 84 1,5 9,4 5 2 156 117 94 1,5 6,7 5 3 112 84 67

212,8 4 1 214 160 128 2 13,9 5 2 231 173 139 2 11,7 5 3 195 147 117

2,5 19,3 4 1 322 241 193 2,5 19,6 5 2 327 245 196 2,5 16,9 5 3 281 211 169

325,8 4 1 431 323 258 3 25,3 5 2 421 316 253 3 25,3 5 3 422 316 253

3,5 35,5 4 1 592 444 355 3,5 34,9 5 2 581 436 349 3,5 27,6 5 3 461 346 276

445,2 4 1 754 566 452 4 43,8 5 2 730 548 438 4 42,9 5 3 714 536 429

4,5 58,3 4 1 971 728 583 4,5 55,8 5 2 929 697 558 4,5 51,0 5 3 849 637 510

571,3 4 1 1188 891 713 5 67,7 5 2 1129 847 677 5 60,3 5 3 1004 753 603

5,5 83,7 4 1 1395 1046 837 5,5 78,5 5 2 1308 981 785 5,5 72,8 5 3 1213 910 728

696,1 4 1 1601 1201 961 6 89,3 5 2 1488 1116 893 6 86,1 5 3 1434 1076 861

6,5 111,2 4 1 1853 1390 1112 6,5 101,9 5 2 1698 1273 1019 6,5 100,9 5 3 1681 1261 1009

7126,3 4 1 2105 1579 1263 7 114,4 5 2 1907 1431 1144 7 113,2 5 3 1886 1415 1132

7,5 135,6 4 1 2260 1695 1356 7,5 128,7 5 2 2145 1609 1287 7,5 122,9 5 3 2048 1536 1229

8144,9 4 1 2416 1812 1449 8 143,0 5 2 2383 1787 1430 8 137,8 5 3 2297 1722 1378

8,5 159,3 4 1 2655 1991 1593 8,5 162,3 5 2 2704 2028 1623 8,5 151,4 5 3 2524 1893 1514

9173,7 4 1 2895 2171 1737 9 181,5 5 2 3024 2268 1815 9 162,4 5 3 2707 2031 1624

9,5 176,5 4 1 2942 2206 1765 9,5 184,7 5 2 3078 2309 1847 9,5 182,0 5 3 3034 2275 1820

10 179,3 4 1 2988 2241 1793 10 187,9 5 2 3131 2348 1879 10 178,6 5 3 2977 2233 1786

6 Metres

kg/min

AMMONIONITRATE 27% GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

NPK 6-9-25 GRANULATED

Opening

lever 2kg/min

Blade

position

Blade

position

Speed (km/h)

Opening

lever

kg/ha

POTASSIUM CHLORIDE 60%

kg/ha

Blade

position

52 di 64

6810 6810 6810

AB AB AB

0,5 1,9 3 1 32 24 19 0,5 2,2 4 1 36 27 22 0,5 4,1 5 3 69 52 41

13,8 3 1 63 47 38 1 4,3 4 1 71 53 43 1 8,5 5 3 141 106 85

1,5 7,0 3 1 117 88 70 1,5 8,7 4 1 144 108 87 1,5 10,1 5 3 169 127 101

210,2 3 1 170 128 102 2 13,0 4 1 216 162 130 2 12,0 5 3 201 151 120

2,5 18,6 3 1 310 233 186 2,5 20,6 4 1 343 257 206 2,5 15,1 5 3 252 189 151

327,0 3 1 449 337 270 3 28,1 4 1 469 352 281 3 19,2 5 3 320 240 192

3,5 37,6 3 1 626 469 376 3,5 36,3 4 1 605 454 363 3,5 18,9 5 3 316 237 189

448,1 3 1 802 601 481 4 44,5 4 1 741 556 445 4 32,1 5 3 535 401 321

4,5 62,1 3 1 1035 776 621 4,5 57,7 4 1 961 721 577 4,5 38,7 5 3 645 484 387

576,1 3 1 1269 952 761 5 70,8 4 1 1180 885 708 5 45,7 5 3 762 571 457

5,5 87,0 3 1 1450 1088 870 5,5 81,8 4 1 1363 1023 818 5,5 57,5 5 3 958 718 575

697,9 3 1 1631 1223 979 6 92,9 4 1 1549 1162 929 6 65,2 5 3 1086 815 652

6,5 116,8 3 1 1947 1460 1168 6,5 114,6 4 1 1910 1433 1146 6,5 72,1 5 3 1201 901 721

7135,7 3 1 2261 1696 1357 7 136,3 4 1 2272 1704 1363 7 83,9 5 3 1399 1049 839

7,5 145,1 3 1 2418 1813 1451 7,5 143,8 4 1 2396 1797 1438 7,5 94,4 5 3 1574 1181 944

8154,4 3 1 2573 1930 1544 8 151,2 4 1 2521 1891 1512 8 109,6 5 3 1827 1370 1096

8,5 161,7 3 1 2695 2021 1617 8,5 168,5 4 1 2808 2106 1685 8,5 128,1 5 3 2135 1601 1281

9169,0 3 1 2817 2113 1690 9 185,7 4 1 3095 2322 1857 9 143,0 5 3 2384 1788 1430

9,5 170,6 3 1 2843 2132 1706 9,5 187,9 4 1 3132 2349 1879 9,5 172,6 5 3 2876 2157 1726

10 172,1 3 1 2868 2151 1721 10 190,1 4 1 3168 2376 1901 10 173,9 5 3 2898 2173 1739

Speed (km/h)

Opening

lever

kg/ha

BIAMMONIUM PHOSPHATE 18-46

kg/ha

Blade

position

Opening

lever 5kg/min

Blade

position

Blade

position

6 Metres

kg/min

NS27-5 BB GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

KALI 49

53 di 64

6810 6810 6810

AB AB AB

0,5 0,9 3 2 15 12 9 0,5 2,2 4 3 37 28 22 0,5 1,9 3 1 32 24 19

11,9 3 2 31 24 19 1 5,4 4 3 90 67 54 1 3,8 3 1 64 48 38

1,5 3,0 3 2 50 37 30 1,5 10,1 4 3 168 126 101 1,5 10,3 3 1 171 128 103

25,2 3 2 87 66 52 2 14,8 4 3 246 185 148 2 16,7 3 1 279 209 167

2,5 6,9 3 2 116 87 69 2,5 21,6 4 3 360 270 216 2,5 24,8 3 1 413 310 248

39,5 3 2 158 118 95 3 28,4 4 3 473 355 284 3 32,9 3 1 548 411 329

3,5 11,5 3 2 192 144 115 3,5 37,0 4 3 616 462 370 3,5 45,4 3 1 756 567 454

424,7 3 2 411 308 247 4 45,5 4 3 758 568 455 4 57,8 3 1 964 723 578

4,5 31,5 3 2 525 394 315 4,5 53,8 4 3 896 672 538 4,5 72,5 3 1 1208 906 725

539,7 3 2 661 496 397 5 62,0 4 3 1034 775 620 5 87,2 3 1 1453 1090 872

5,5 48,7 3 2 812 609 487 5,5 73,6 4 3 1226 919 736 5,5 98,8 3 1 1646 1234 988

655,0 3 2 917 688 550 6 85,1 4 3 1419 1064 851 6 110,3 3 1 1838 1379 1103

6,5 61,6 3 2 1027 770 616 6,5 91,1 4 3 1518 1138 911 6,5 130,4 3 1 2173 1630 1304

772,4 3 2 1207 905 724 7 97,0 4 3 1617 1213 970 7 150,5 3 1 2508 1881 1505

7,5 82,9 3 2 1382 1036 829 7,5 100,0 4 3 1667 1250 1000 7,5 165,3 3 1 2754 2066 1653

898,3 3 2 1638 1228 983 8 103,0 4 3 1717 1288 1030 8 180,0 3 1 3000 2250 1800

8,5 114,0 3 2 1900 1425 1140 8,5 114,2 4 3 1903 1428 1142 8,5 173,0 3 1 2883 2162 1730

9131,0 3 2 2183 1637 1310 9 125,5 4 3 2092 1569 1255 9 195,8 3 1 3263 2447 1958

9,5 172,5 3 2 2875 2156 1725 9,5 125,7 4 3 2095 1571 1257 9,5 209,9 3 1 3498 2624 2099

10 180,1 3 2 3002 2252 1801 10 126,0 4 3 2100 1575 1260 10 224,0 3 1 3733 2800 2240

6 Metres

kg/min

UREA

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

UREA PRILLED AGRICOLA

Opening

lever 8kg/min

Blade

position

Blade

position

Speed (km/h)

Opening

lever

kg/ha

NPK 22-2-12 PRILLED

kg/ha

Blade

position

54 di 64

6810 6810 6810

AB AB AB

0,5 2,0 4 1 16 12 10 0,5 2,4 4 1 20 15 12 0,5 1,0 52865

13,9 4 1 32 24 19 1 4,8 4 1 40 30 24 1 4,1 5 2 34 26 20

1,5 8,4 4 1 70 52 42 1,5 9,4 4 1 78 58 47 1,5 6,7 5 2 56 42 34

212,8 4 1 107 80 64 2 13,9 4 1 116 87 69 2 11,7 5 2 98 73 59

2,5 19,3 4 1 161 121 97 2,5 19,6 4 1 163 123 98 2,5 16,9 5 2 140 105 84

325,8 4 1 215 161 129 3 25,3 4 1 211 158 126 3 25,3 5 2 211 158 127

3,5 35,5 4 1 296 222 178 3,5 34,9 4 1 290 218 174 3,5 27,6 5 2 230 173 138

445,2 4 1 377 283 226 4 43,8 4 1 365 274 219 4 42,9 5 2 357 268 214

4,5 58,3 4 1 485 364 291 4,5 55,8 4 1 465 348 279 4,5 51,0 5 2 425 318 255

571,3 4 1 594 445 356 5 67,7 4 1 564 423 339 5 60,3 5 2 502 377 301

5,5 83,7 4 1 698 523 419 5,5 78,5 4 1 654 491 393 5,5 72,8 5 2 607 455 364

696,1 4 1 800 600 480 6 89,3 4 1 744 558 446 6 86,1 5 2 717 538 430

6,5 111,2 4 1 927 695 556 6,5 101,9 4 1 849 637 509 6,5 100,9 5 2 840 630 504

7126,3 4 1 1053 789 632 7 114,4 4 1 954 715 572 7 113,2 5 2 943 707 566

7,5 135,6 4 1 1130 848 678 7,5 128,7 4 1 1073 804 644 7,5 122,9 5 2 1024 768 614

8144,9 4 1 1208 906 725 8 143,0 4 1 1191 894 715 8 137,8 5 2 1148 861 689

8,5 159,3 4 1 1328 996 797 8,5 162,3 4 1 1352 1014 811 8,5 151,4 5 2 1262 947 757

9173,7 4 1 1448 1086 869 9 181,5 4 1 1512 1134 907 9 162,4 5 2 1354 1015 812

9,5 176,5 4 1 1471 1103 883 9,5 184,7 4 1 1539 1154 924 9,5 182,0 5 2 1517 1138 910

10 179,3 4 1 1494 1120 896 10 187,9 4 1 1566 1174 939 10 178,6 5 2 1489 1116 893

Speed (km/h)

Opening

lever

kg/ha

POTASSIUM CHLORIDE 60%

kg/ha

Blade

position

Opening

lever 2kg/min

Blade

position

Blade

position

12 Metres

kg/min

AMMONIONITRATE 27% GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

NPK 6-9-25 GRANULATED

55 di 64

6810 6810 6810

AB AB AB

0,5 1,9 3 1 16 12 10 0,5 2,2 4 1 18 13 11 0,5 4,1 4 2 35 26 21

13,8 3 1 32 24 19 1 4,3 4 1 35 27 21 1 8,5 4 2 71 53 42

1,5 7,0 3 1 58 44 35 1,5 8,7 4 1 72 54 43 1,5 10,1 4 2 84 63 51

210,2 3 1 85 64 51 2 13,0 4 1 108 81 65 2 12,0 4 2 100 75 60

2,5 18,6 3 1 155 116 93 2,5 20,6 4 1 171 128 103 2,5 15,1 4 2 126 95 76

327,0 3 1 225 169 135 3 28,1 4 1 235 176 141 3 19,2 4 2 160 120 96

3,5 37,6 3 1 313 235 188 3,5 36,3 4 1 303 227 182 3,5 18,9 4 2 158 118 95

448,1 3 1 401 301 241 4 44,5 4 1 371 278 222 4 32,1 4 2 268 201 161

4,5 62,1 3 1 518 388 311 4,5 57,7 4 1 480 360 288 4,5 38,7 4 2 322 242 193

576,1 3 1 635 476 381 5 70,8 4 1 590 443 354 5 45,7 4 2 381 286 229

5,5 87,0 3 1 725 544 435 5,5 81,8 4 1 682 511 409 5,5 57,5 4 2 479 359 287

697,9 3 1 815 612 489 6 92,9 4 1 774 581 465 6 65,2 4 2 543 407 326

6,5 116,8 3 1 973 730 584 6,5 114,6 4 1 955 716 573 6,5 72,1 4 2 601 450 360

7135,7 3 1 1131 848 678 7 136,3 4 1 1136 852 681 7 83,9 4 2 699 524 420

7,5 145,1 3 1 1209 907 725 7,5 143,8 4 1 1198 898 719 7,5 94,4 4 2 787 590 472

8154,4 3 1 1287 965 772 8 151,2 4 1 1260 945 756 8 109,6 4 2 913 685 548

8,5 161,7 3 1 1348 1011 809 8,5 168,5 4 1 1404 1053 842 8,5 128,1 4 2 1068 801 641

9169,0 3 1 1408 1056 845 9 185,7 4 1 1548 1161 929 9 143,0 4 2 1192 894 715

9,5 170,6 3 1 1421 1066 853 9,5 187,9 4 1 1566 1174 940 9,5 172,6 4 2 1438 1079 863

10 172,1 3 1 1434 1076 861 10 190,1 4 1 1584 1188 950 10 173,9 4 2 1449 1087 869

12 Metres

kg/min

NS27-5 BB GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

KALI 49

Opening

lever 5kg/min

Blade

position

Blade

position

Speed (km/h)

Opening

lever

kg/ha

BIAMMONIUM PHOSPHATE 18-46

kg/ha

Blade

position

56 di 64

6810 6810 6810

AB AB AB

0,5 2,1 3 1 17 13 10 0,5 2,2 3 2 18 14 11 0,5 1,9 4 1 16 12 10

14,2 3 1 35 26 21 1 5,4 3 2 45 34 27 1 3,8 4 1 32 24 19

1,5 6,7 3 1 56 42 34 1,5 10,1 3 2 84 63 51 1,5 10,3 4 1 85 64 51

29,2 3 1 77 58 46 2 14,8 3 2 123 92 74 2 16,7 4 1 139 104 84

2,5 14,2 3 1 118 89 71 2,5 21,6 3 2 180 135 108 2,5 24,8 4 1 207 155 124

319,1 3 1 160 120 96 3 28,4 3 2 237 178 142 3 32,9 4 1 274 206 164

3,5 25,4 3 1 212 159 127 3,5 37,0 3 2 308 231 185 3,5 45,4 4 1 378 283 227

431,7 3 1 264 198 159 4 45,5 3 2 379 284 227 4 57,8 4 1 482 362 289

4,5 38,3 3 1 319 239 192 4,5 53,8 3 2 448 336 269 4,5 72,5 4 1 604 453 363

544,9 3 1 374 281 225 5 62,0 3 2 517 388 310 5 87,2 4 1 726 545 436

5,5 53,0 3 1 441 331 265 5,5 73,6 3 2 613 460 368 5,5 98,8 4 1 823 617 494

661,0 3 1 509 382 305 6 85,1 3 2 710 532 426 6 110,3 4 1 919 689 551

6,5 70,4 3 1 587 440 352 6,5 91,1 3 2 759 569 455 6,5 130,4 4 1 1087 815 652

779,8 3 1 665 499 399 7 97,0 3 2 808 606 485 7 150,5 4 1 1254 941 752

7,5 91,2 3 1 760 570 456 7,5 100,0 3 2 833 625 500 7,5 165,3 4 1 1377 1033 826

8102,7 3 1 856 642 513 8 103,0 3 2 858 644 515 8 180,0 4 1 1500 1125 900

8,5 115,1 3 1 959 719 575 8,5 114,2 3 2 952 714 571 8,5 173,0 4 1 1442 1081 865

9127,4 3 1 1062 796 637 9 125,5 3 2 1046 784 627 9 195,8 4 1 1631 1224 979

9,5 127,8 3 1 1065 798 639 9,5 125,7 3 2 1048 786 629 9,5 209,9 4 1 1749 1312 1050

10 128,1 3 1 1068 801 641 10 126,0 3 2 1050 788 630 10 224,0 4 1 1867 1400 1120

Speed (km/h)

Opening

lever

kg/ha

NPK 22-2-12 PRILLED

kg/ha

Blade

position

Opening

lever 8kg/min

Blade

position

Blade

position

12 Metres

kg/min

UREA

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

UREA PRILLED AGRICOLA

57 di 64

6810 6810 6810

AB AB AB

0,5 2,0 4 1 13 10 8 0,5 2,4 4 1 16 12 10 0,5 1,0 52754

13,9 4 1 26 19 15 1 4,8 4 1 32 24 19 1 4,1 5 2 27 20 16

1,5 8,4 4 1 56 42 33 1,5 9,4 4 1 62 47 37 1,5 6,7 5 2 45 34 27

212,8 4 1 85 64 51 2 13,9 4 1 92 69 55 2 11,7 5 2 78 59 47

2,5 19,3 4 1 129 97 77 2,5 19,6 4 1 131 98 78 2,5 16,9 5 2 112 84 67

325,8 4 1 172 129 103 3 25,3 4 1 169 126 101 3 25,3 5 2 169 127 101

3,5 35,5 4 1 237 178 142 3,5 34,9 4 1 232 174 139 3,5 27,6 5 2 184 138 111

445,2 4 1 302 226 181 4 43,8 4 1 292 219 175 4 42,9 5 2 286 214 171

4,5 58,3 4 1 388 291 233 4,5 55,8 4 1 372 279 223 4,5 51,0 5 2 340 255 204

571,3 4 1 475 356 285 5 67,7 4 1 452 339 271 5 60,3 5 2 402 301 241

5,5 83,7 4 1 558 419 335 5,5 78,5 4 1 523 393 314 5,5 72,8 5 2 485 364 291

696,1 4 1 640 480 384 6 89,3 4 1 595 446 357 6 86,1 5 2 574 430 344

6,5 111,2 4 1 741 556 445 6,5 101,9 4 1 679 509 407 6,5 100,9 5 2 672 504 403

7126,3 4 1 842 632 505 7 114,4 4 1 763 572 458 7 113,2 5 2 755 566 453

7,5 135,6 4 1 904 678 542 7,5 128,7 4 1 858 644 515 7,5 122,9 5 2 819 614 492

8144,9 4 1 966 725 580 8 143,0 4 1 953 715 572 8 137,8 5 2 919 689 551

8,5 159,3 4 1 1062 797 637 8,5 162,3 4 1 1082 811 649 8,5 151,4 5 2 1010 757 606

9173,7 4 1 1158 869 695 9 181,5 4 1 1210 907 726 9 162,4 5 2 1083 812 650

9,5 176,5 4 1 1177 883 706 9,5 184,7 4 1 1231 924 739 9,5 182,0 5 2 1213 910 728

10 179,3 4 1 1195 896 717 10 187,9 4 1 1252 939 751 10 178,6 5 2 1191 893 715

15 Metres

kg/min

AMMONIONITRATE 27% GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

NPK 6-9-25 GRANULATED

Opening

lever 2kg/min

Blade

position

Blade

position

Speed (km/h)

Opening

lever

kg/ha

POTASSIUM CHLORIDE 60%

kg/ha

Blade

position

58 di 64

6810 6810 6810

AB AB AB

0,5 1,9 3 1 13 10 8 0,5 2,2 4 1 14 11 9 0,5 4,1 4 2 28 21 17

13,8 3 1 25 19 15 1 4,3 4 1 28 21 17 1 8,5 4 2 56 42 34

1,5 7,0 3 1 47 35 28 1,5 8,7 4 1 58 43 35 1,5 10,1 4 2 68 51 41

210,2 3 1 68 51 41 2 13,0 4 1 86 65 52 2 12,0 4 2 80 60 48

2,5 18,6 3 1 124 93 74 2,5 20,6 4 1 137 103 82 2,5 15,1 4 2 101 76 60

327,0 3 1 180 135 108 3 28,1 4 1 188 141 113 3 19,2 4 2 128 96 77

3,5 37,6 3 1 250 188 150 3,5 36,3 4 1 242 182 145 3,5 18,9 4 2 126 95 76

448,1 3 1 321 241 192 4 44,5 4 1 296 222 178 4 32,1 4 2 214 161 128

4,5 62,1 3 1 414 311 248 4,5 57,7 4 1 384 288 231 4,5 38,7 4 2 258 193 155

576,1 3 1 508 381 305 5 70,8 4 1 472 354 283 5 45,7 4 2 305 229 183

5,5 87,0 3 1 580 435 348 5,5 81,8 4 1 545 409 327 5,5 57,5 4 2 383 287 230

697,9 3 1 652 489 391 6 92,9 4 1 620 465 372 6 65,2 4 2 435 326 261

6,5 116,8 3 1 779 584 467 6,5 114,6 4 1 764 573 458 6,5 72,1 4 2 480 360 288

7135,7 3 1 904 678 543 7 136,3 4 1 909 681 545 7 83,9 4 2 559 420 336

7,5 145,1 3 1 967 725 580 7,5 143,8 4 1 958 719 575 7,5 94,4 4 2 630 472 378

8154,4 3 1 1029 772 618 8 151,2 4 1 1008 756 605 8 109,6 4 2 731 548 438

8,5 161,7 3 1 1078 809 647 8,5 168,5 4 1 1123 842 674 8,5 128,1 4 2 854 641 512

9169,0 3 1 1127 845 676 9 185,7 4 1 1238 929 743 9 143,0 4 2 954 715 572

9,5 170,6 3 1 1137 853 682 9,5 187,9 4 1 1253 940 752 9,5 172,6 4 2 1151 863 690

10 172,1 3 1 1147 861 688 10 190,1 4 1 1267 950 760 10 173,9 4 2 1159 869 695

Speed (km/h)

Opening

lever

kg/ha

BIAMMONIUM PHOSPHATE 18-46

kg/ha

Blade

position

Opening

lever 5kg/min

Blade

position

Blade

position

15 Metres

kg/min

NS27-5 BB GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

KALI 49

59 di 64

6810 6810 6810

AB AB AB

0,5 2,0 4 1 11 8 7 0,5 2,4 3 1 13 10 8 0,5 1,0 41643

13,9 4 1 21 16 13 1 4,8 3 1 26 20 16 1 4,1 4 1 23 17 14

1,5 8,4 4 1 46 35 28 1,5 9,4 3 1 52 39 31 1,5 6,7 4 1 37 28 22

212,8 4 1 71 53 43 2 13,9 3 1 77 58 46 2 11,7 4 1 65 49 39

2,5 19,3 4 1 107 80 64 2,5 19,6 3 1 109 82 65 2,5 16,9 4 1 94 70 56

325,8 4 1 144 108 86 3 25,3 3 1 140 105 84 3 25,3 4 1 141 105 84

3,5 35,5 4 1 197 148 118 3,5 34,9 3 1 194 145 116 3,5 27,6 4 1 154 115 92

445,2 4 1 251 189 151 4 43,8 3 1 243 183 146 4 42,9 4 1 238 179 143

4,5 58,3 4 1 324 243 194 4,5 55,8 3 1 310 232 186 4,5 51,0 4 1 283 212 170

571,3 4 1 396 297 238 5 67,7 3 1 376 282 226 5 60,3 4 1 335 251 201

5,5 83,7 4 1 465 349 279 5,5 78,5 3 1 436 327 262 5,5 72,8 4 1 404 303 243

696,1 4 1 534 400 320 6 89,3 3 1 496 372 298 6 86,1 4 1 478 359 287

6,5 111,2 4 1 618 463 371 6,5 101,9 3 1 566 424 340 6,5 100,9 4 1 560 420 336

7126,3 4 1 702 526 421 7 114,4 3 1 636 477 381 7 113,2 4 1 629 472 377

7,5 135,6 4 1 753 565 452 7,5 128,7 3 1 715 536 429 7,5 122,9 4 1 683 512 410

8144,9 4 1 805 604 483 8 143,0 3 1 794 596 477 8 137,8 4 1 766 574 459

8,5 159,3 4 1 885 664 531 8,5 162,3 3 1 901 676 541 8,5 151,4 4 1 841 631 505

9173,7 4 1 965 724 579 9 181,5 3 1 1008 756 605 9 162,4 4 1 902 677 541

9,5 176,5 4 1 981 735 588 9,5 184,7 3 1 1026 770 616 9,5 182,0 4 1 1011 758 607

10 179,3 4 1 996 747 598 10 187,9 3 1 1044 783 626 10 178,6 4 1 992 744 595

18 Metres

kg/min

AMMONIONITRATE 27% GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

NPK 6-9-25 GRANULATED

Opening

lever 2kg/min

Blade

position

Blade

position

Speed (km/h)

Opening

lever

kg/ha

POTASSIUM CHLORIDE 60%

kg/ha

Blade

position

60 di 64

6810 6810 6810

AB AB AB

0,5 1,9 3 1 11 8 6 0,5 2,2 4 1 12 9 7 0,5 4,1 4 1 23 17 14

13,8 3 1 21 16 13 1 4,3 4 1 24 18 14 1 8,5 4 1 47 35 28

1,5 7,0 3 1 39 29 23 1,5 8,7 4 1 48 36 29 1,5 10,1 4 1 56 42 34

210,2 3 1 57 43 34 2 13,0 4 1 72 54 43 2 12,0 4 1 67 50 40

2,5 18,6 3 1 103 78 62 2,5 20,6 4 1 114 86 69 2,5 15,1 4 1 84 63 50

327,0 3 1 150 112 90 3 28,1 4 1 156 117 94 3 19,2 4 1 107 80 64

3,5 37,6 3 1 209 156 125 3,5 36,3 4 1 202 151 121 3,5 18,9 4 1 105 79 63

448,1 3 1 267 200 160 4 44,5 4 1 247 185 148 4 32,1 4 1 178 134 107

4,5 62,1 3 1 345 259 207 4,5 57,7 4 1 320 240 192 4,5 38,7 4 1 215 161 129

576,1 3 1 423 317 254 5 70,8 4 1 393 295 236 5 45,7 4 1 254 190 152

5,5 87,0 3 1 483 363 290 5,5 81,8 4 1 454 341 273 5,5 57,5 4 1 319 239 192

697,9 3 1 544 408 326 6 92,9 4 1 516 387 310 6 65,2 4 1 362 272 217

6,5 116,8 3 1 649 487 389 6,5 114,6 4 1 637 478 382 6,5 72,1 4 1 400 300 240

7135,7 3 1 754 565 452 7 136,3 4 1 757 568 454 7 83,9 4 1 466 350 280

7,5 145,1 3 1 806 604 484 7,5 143,8 4 1 799 599 479 7,5 94,4 4 1 525 394 315

8154,4 3 1 858 643 515 8 151,2 4 1 840 630 504 8 109,6 4 1 609 457 365

8,5 161,7 3 1 898 674 539 8,5 168,5 4 1 936 702 562 8,5 128,1 4 1 712 534 427

9169,0 3 1 939 704 563 9 185,7 4 1 1032 774 619 9 143,0 4 1 795 596 477

9,5 170,6 3 1 948 711 569 9,5 187,9 4 1 1044 783 626 9,5 172,6 4 1 959 719 575

10 172,1 3 1 956 717 574 10 190,1 4 1 1056 792 634 10 173,9 4 1 966 724 580

Speed (km/h)

Opening

lever

kg/ha

BIAMMONIUM PHOSPHATE 18-46

kg/ha

Blade

position

Opening

lever 5kg/min

Blade

position

Blade

position

18 Metres

kg/min

NS27-5 BB GRANULATED

kg/min

Opening

lever kg/ha

NORMAL SPREADING

Speed (km/h) Speed (km/h)

KALI 49

61 di 64

www.agrex.com

Tavola Rif. Codice Q.tà Descrizione

Table Ref. Part no. Q.ty Description

Table Réf. Code Q.té Description

Tabla Ref. Código Cant. Descripción

Tafel Num. Code M.ge Schilderung

Data - Date - Datum - Date - Fecha - Data

Cliente - Customer - Client - Cliente - Kunde

Tipo di macchina - Machine type - Type de machine - Tipo de máquina - Maschinentyp

Modello - Model - Modèle - Modelo - Modell Matricola - Serial no. - Matricule - Matrícula - Kennummer

(1) Indicare la versione del Catalogo Ricambi (rilevabile sulla copertina dello stesso) / Specify the Spare Parts Catalog version number (see the front cover of the catalog) / Préciser la

version du Catalogue Pièces de rechange (indiquée sur la couverture de celui-ci) / Indicar la versión del Catálogo Repuestos (se encuentra en la cubierta del mismo) / Die Ausfuehrung des

Ersatzteilkataloges angeben (wie auf Frontseite ersehbar):

Modulo ordinazione parti di ricambio

Spare parts order form

Formulaire de commande pieces de rechange

Modulo pedido piezas de repuesto

Ersatzteilbestellungsformular

AGREX S.p.a.

Production & Sales Dept:

Via Balla, 55/57 (Loc. Taggì di Sotto)

35010 Villafranca Padovana - (Padova) - Italia

Tel. +39 049 90 75 684

Fax. +39 049 90 75 524

E-mail: info@agrex.com

(1) update:

Timbro e rma:

Stamp and signature:

Timbre et signature:

Sello y rma:

Stempel und Unterzeichnung:

Tavola Rif. Codice Q.tà Descrizione

Table Ref. Part no. Q.ty Description

Table Réf. Code Q.té Description

Tabla Ref. Código Cant. Descripción

Tafel Num. Code M.ge Schilderung

Data - Date - Datum - Date - Fecha - Data

Cliente - Customer - Client - Cliente - Kunde

Tipo di macchina - Machine type - Type de machine - Tipo de máquina - Maschinentyp

Modello - Model - Modèle - Modelo - Modell Matricola - Serial no. - Matricule - Matrícula - Kennummer

(1) Indicare la versione del Catalogo Ricambi (rilevabile sulla copertina dello stesso) / Specify the Spare Parts Catalog version number (see the front cover of the catalog) / Préciser la

version du Catalogue Pièces de rechange (indiquée sur la couverture de celui-ci) / Indicar la versión del Catálogo Repuestos (se encuentra en la cubierta del mismo) / Die Ausfuehrung des

Ersatzteilkataloges angeben (wie auf Frontseite ersehbar):

Modulo ordinazione parti di ricambio

Spare parts order form

Formulaire de commande pieces de rechange

Modulo pedido piezas de repuesto

Ersatzteilbestellungsformular

AGREX S.p.a.

Production & Sales Dept:

Via Balla, 55/57 (Loc. Taggì di Sotto)

35010 Villafranca Padovana - (Padova) - Italia

Tel. +39 049 90 75 684

Fax. +39 049 90 75 524

E-mail: info@agrex.com

(1) update:

Timbro e rma:

Stamp and signature:

Timbre et signature:

Sello y rma:

Stempel und Unterzeichnung:

AGREX S.p.A.

Production & Sales Dept:

Via Balla, 55/57 (Loc. Taggì di Sotto)

35010 Villafranca Padovana (PD) - ITALIA

Tel. +39 049 50 00 000

Fax. +39 049 90 75 524

E-mail: info@agrex.com

Web Site: www.agrex.com

Manuale SDA_en AGREX SDA500 600

Navigation menu

Versions of this User Manual:

Views

Navigation