N6700 Series Specifications Guide A_N6705A A N6705A
N6700-900011 N6700-900011
User Manual: A_N6705A
Open the PDF directly: View PDF 
.
Page Count: 51
| Download | |
| Open PDF In Browser | View PDF |
Agilent N6700 Modular Power System Family N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Legal Notices © Agilent Technologies, Inc. 2010 - 2012 No part of this document may be photocopied, reproduced, or translated to another language without the prior agreement and written consent of Agilent Technologies, Inc. as governed by United States and international copyright laws. Warranty The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. Manual Editions Manual Part Number: N6700-90001 Sixth Edition, February 2012 Available in electronic format only. Updates of this manual containing minor corrections may have the same edition date. Revised editions are identified by a new edition date. 2 Certification Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institute's calibration facility, and to the calibration facilities of other International Standards Organization members. Technologies Licenses The hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license. U.S. Government Restricted Rights Software and technical data rights granted to the federal government include only those rights customarily provided to end user customers. Agilent provides this customary commercial license in Software and technical data pursuant to FAR 12.211 (Technical Data) and 12.212 (Computer Software) and, for the Department of Defense, DFARS 252.2277015 (Technical Data – Commercial Items) and DFARS 227.7202-3 (Rights in Commercial Computer Software or Computer Software Documentation). Declaration of Conformity Declarations of Conformity for this product and for other Agilent products may be downloaded from the Web. Go to http://regulations.corporate.agilent.com and click on “Declarations of Conformity.” You can then search by product number to find the latest Declaration of Conformity. Regulatory Symbols The CE mark shows that the product complies with all applicable European Directives. The C-Tick mark is a registered trademark of the Australian Communications Authority. This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. This is the symbol for an Industrial, Scientific and Medical, Group 1 Class A product. The CSA mark is a registered trademark of Intertek-etlsemko Inc. This is the RoHS (Restriction of Hazardous Substances) symbol for electrical and electronic equipment. This symbol indicates separate collection for electrical and electronic equipment mandated under EU law as of August 13, 2005. All electric and electronic equipment are required to be separated from normal waste for disposal (Reference WEEE Directive 2002/96/EC). N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Where to Find More Information This document provides specification and supplemental characteristic information for the following instruments: • Agilent N6731B through N6784A Power Modules • Agilent N6700B through N6705B Mainframes For additional technical details and ordering information for the Agilent N6700 Modular Power System Family, refer to the following: Document Description Agilent N6700 Modular Power System Family: Low-Profile MPS Mainframe for Automated Test Environments The Agilent N6700 Low-Profile Modular Power System (MPS) is a 1U (rack unit) high, multiple-output programmable DC power supply system that enables test system integrators to optimize performance, power and price to match test needs. Go to: http://cp.literature.agilent.com/litweb/pdf/5989-1411EN.pdf Agilent N6700 Modular Power System Family: DC Power Analyzer Mainframe for R&D The Agilent N6705 DC Power Analyzer represents an entirely new instrument category for R&D engineers. It provides unrivaled productivity gains when sourcing and measuring DC voltage and current into a DUT. Using the Agilent N6705 DC Power Analyzer, R&D engineers can gain insights into the DUT’s power consumption in minutes, with all sourcing and measuring functions available from the front panel. Go to: http://cp.literature.agilent.com/litweb/pdf/5989-6319EN.pdf Agilent N6700 Modular Power System Family: N6780 Series Source/Measure Units The Agilent N6781A and N6782A 2-quadrant SMUs offer advanced sourcing and measurement capabilities required to overcome test challenges associated with optimizing power consumption and maximizing battery life of battery-powered devices and their components. The Agilent N6784A 4-quadrant SMU offers advanced sourcing and measurement capabilities in four quadrants for general purpose applications. Go to: http://cp.literature.agilent.com/litweb/pdf/5990-5829EN.pdf Agilent N6700 Modular Power System Family: Battery Charge/Discharge Module The Agilent N6783A-BAT battery charge/discharge module is a basic, 2-quadrant DC power module designed to be used by mobile device designers. Its 2-quadrant operation allows it to act as a programmable power supply to charge the battery or as a programmable electronic load to discharge the battery, all in one instrument. Go to: http://cp.literature.agilent.com/litweb/pdf/5990-8662EN.pdf Agilent N6700 Modular Power System Family: Mobile Communications DC Power Module The Agilent N6783A-MFG mobile communications DC power module offers advanced features specifically for testing battery-powered (mobile) devices in manufacturing or automated test environments. Go to: http://cp.literature.agilent.com/litweb/pdf/5990-8643EN.pdf NOTE You can contact Agilent Technologies at one of the following telephone numbers for warranty, service, or technical support information. In the United States: (800) 829-4444 In Europe: 31 20 547 2111 In Japan: 0120-421-345 Or use our Web link for information on contacting Agilent in your country or specific location: www.agilent.com/find/assist Or contact your Agilent Technologies Representative. The web contains the most up to date version of this manual. Go to http://cp.literature.agilent.com/litweb/pdf/N6700-90001.pdf. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 3 Contents 1 - Power Module Differences...................................................................................................... 5 Power Module Differences–for Agilent N6700 Modular Power Systems . 6 Power Module Differences–for Agilent N6705 DC Power Analyzers ........ 8 Power Module Option Characteristics .......................................................... 10 2 - Agilent N673xB, N674xB, N677xA DC Power Modules ...................................................11 Performance Specifications ............................................................................ 12 Supplemental Characteristics ......................................................................... 14 Output Quadrant Characteristic ...................................................................... 16 Arbitrary Waveform Generator Maximum Bandwidth ................................ 16 3 - Agilent N675xA High Performance Power Modules .........................................................19 Performance Specifications ............................................................................ 20 Supplemental Characteristics ......................................................................... 21 Autoranging Characteristic.............................................................................. 23 Output Impedance Graphs ............................................................................... 23 Arbitrary Waveform Generator Maximum Bandwidth ................................ 26 4 - Agilent N676xA Precision Power Modules.........................................................................27 Performance Specifications ............................................................................ 28 Supplemental Characteristics ......................................................................... 29 Autoranging Characteristic.............................................................................. 31 Output Impedance Graphs ............................................................................... 31 Arbitrary Waveform Generator Maximum Bandwidth ................................ 34 5 - Agilent N6781A, N6782A, N6784A Source/Measure Units ..............................................35 Performance Specifications ............................................................................ 36 Supplemental Characteristics ......................................................................... 37 Output Quadrant Characteristic ...................................................................... 42 Output Impedance Graphs ............................................................................... 42 6 - Agilent N6783A-BAT, N6783A-MFG Application-Specific Power Modules...................43 Performance Specifications ............................................................................ 44 Supplemental Characteristics ......................................................................... 45 Output Quadrant Characteristic ...................................................................... 46 7 - Agilent N6700 Modular Power System Mainframes .........................................................47 Supplemental Characteristics ......................................................................... 48 Outline Diagrams............................................................................................... 50 4 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 1 Power Module Differences Power Module Differences–for Agilent N6700 Modular Power Systems . 6 Power Module Differences–for Agilent N6705 DC Power Analyzers ........ 8 Power Module Option Characteristics .......................................................... 10 This chapter provides a brief overview of the basic differences between the Agilent N6700 series DC Power Modules. Note that the basic capabilities of a power module depend not only on its hardware capabilities, but also the on the hardware and firmware capabilities of the mainframe in which it is installed. In addition to their primary output and measurement capabilities, power modules installed in an Agilent N6705 DC Power Analyzer have expanded capabilities such as front panel scope view, arbitrary waveform generation, and internal and external data logging. Refer to the Agilent N6700 or N6705 User’s Guide for more information about the power module capabilities. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 5 Power Module Differences–for Agilent N6700 Modular Power Systems Agilent N6731B–N6777A Differences Feature DC Power High-Performance Precision N673xB, N674xB, N677xA N675xA N676xA 50 W output rating N6731B – N6736B N6751A N6761A 100 W output rating N6741B – N6746B N6752A N6762A 300 W output rating N6773A – N6777A N6753A, N6754A N6763A, N6764A N6755A, N6756A N6765A, N6766A (● = available) 500 W output rating Output disconnect relays Option 761 Option 761 Option 761 Output disconnect/polarity reversal relays NOTE 1 Option 760 Option 760 Option 760 ● ● Autoranging output capability Voltage or current turn-on priority N6761A, N6762A Precision voltage and current measurements ● Low voltage and current output ranges N6761A, N6762A Low voltage and current measurement ranges 200 microampere measurement range ● Option 2UA NOTE 2 Simultaneous voltage and current measurements SCPI command output list capability NOTE 3 SCPI command array readback NOTE 3 SCPI command programmable sample rate NOTE 3 SCPI command external data logging NOTE 3 ● Option 054 Option 054 ● Option 054 Option 054 ● Option 054 Option 054 ● Option 054 Option 054 ● N6753A – N6756A N6763A – N6766A Double-wide (occupies 2 channel locations) Option 760 limits the output current to 10A maximum on Models N6742B and N6773A. 1 Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, and N6762A. 2 Option 2UA.is only available on Models N6761A and N6762A. It includes Option 761. 3 Only available when using the remote interfaces; not from the front panel. 6 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Agilent N6781A–N6784A Differences Feature Source/Measure Units (SMU) Application-Specific (● = available) N6781A N6782A N6784A N6783A-BAT N6783A-MFG Output rating 20 W 20 W 20 W 24 W 18 W ● ● ● ● ● Option 761 Option 761 ● ● ● ● 2-quadrant operation 4-quadrant operation ● Auxiliary voltage measurement input ● Output disconnect relays ● Negative voltage protection ● ● ● Voltage or current priority mode ● ● ● Programmable output resistance ● 600 mV output range ● ● ● 300 mA output range ● ● ● 100 mA, 10 mA output ranges ● 1 V, 100 mV measurement ranges ● ● ● 100 mA, 1 mA, 10 μA measurement ranges ● ● ● Simultaneous voltage and current measurements ● ● ● Seamless measurement autoranging ● ● 150 mA measurement range SCPI command output list capability NOTE 1, 2 ● ● ● ● ● ● ● ● ● ● SCPI command programmable sample rate NOTE 2 ● ● ● ● ● SCPI command external data logging ● ● ● ● ● SCPI command array readback NOTE 2 NOTE 2 1 List capability is not available on the negative current output on Model N6783A. 2 Only available when using the remote interfaces; not the front panel. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 7 Power Module Differences–for Agilent N6705 DC Power Analyzers Agilent N6731B–N6777A Differences Feature DC Power High-Performance Precision N673xB, N674xB, N677xA N675xA N676xA 50 W output rating N6731B – N6736B N6751A N6761A 100 W output rating N6741B – N6746B N6752A N6762A 300 W output rating N6773A – N6777A N6753A, N6754A N6763A, N6764A N6755A, N6756A N6765A, N6766A (● = available) 500 W output rating Output disconnect relays Option 761 Option 761 Option 761 Output disconnect/polarity reversal relays NOTE 1 Option 760 Option 760 Option 760 ● ● ● ● ● Arbitrary waveform generation Autoranging output capability Voltage or current turn-on priority N6761A, N6762A Precision voltage and current measurements ● Low voltage and current output ranges N6761A, N6762A Low voltage and current measurement ranges ● 200 microampere measurement range NOTE 2 Option 2UA Voltage or current scope traces ● ● Simultaneous voltage and current scope traces Simultaneous voltage and current data logging ● ● ● NOTE 3 Interleaved voltage and current data logging NOTE 3 ● ● Dynamic current correction ● N6751A, N6752A N6761A, N6762A ● ● ● ● ● ● SCPI command programmable sample rate NOTE 4 ● ● ● SCPI command external data logging ● ● ● N6753A – N6756A N6763A – N6766A SCPI command output list capability NOTE 4 SCPI command array readback NOTE 4 NOTE 4 Double-wide (occupies 2 channel locations) Option 760 limits the output current to 10A maximum on Models N6742B and N6773A. 1 Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, and N6762A. 2 Option 2UA is only available on Models N6761A and N6762A. It includes Option 761. 3 Option 055 deletes the Data Logger function on Model N6705. 4 Only available when using the remote interfaces; not from the front panel. 8 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Agilent N6781A–N6784A Differences Feature Source/Measure Units (SMU) Application-Specific (● = available) N6781A N6782A N6784A N6783A-BAT N6783A-MFG Output rating 20 W 20 W 20 W 24 W 18 W ● ● ● ● 2-quadrant operation 4-quadrant operation ● Auxiliary voltage measurement input ● Output disconnect relays ● ● ● Option 761 Option 761 Arbitrary waveform generation NOTE 1 ● ● ● ● ● Negative voltage protection ● ● ● ● ● Voltage or current priority mode ● ● ● CC load/CV load ● ● ● Battery emulator/charger ● ● ● Voltage/current measurement only ● ● ● Programmable output resistance ● 600 mV output range ● ● ● 300 mA output range ● ● ● ● ● ● ● ● 100 mA, 10 mA output ranges ● 1 V, 100 mV measurement ranges ● ● ● 100 mA, 1 mA, 10 μA measurement ranges ● ● ● 150 mA measurement range Voltage or current scope traces Simultaneous voltage and current scope traces Simultaneous voltage and current data logging NOTE 2 ● ● ● ● ● ● ● ● ● Interleaved voltage and current data logging NOTE 2 Seamless measurement autoranging SCPI command output list capability SCPI command array readback NOTE 1, 3 ● ● ● ● ● ● ● ● ● ● ● ● SCPI command programmable sample rate NOTE 3 ● ● ● ● ● SCPI command external data logging ● ● ● ● ● ● ● NOTE 3 NOTE 3 SCPI command histogram measurements NOTE 3 1 Arbitrary waveform generation and list capability are not available on the negative current output on Model N6783A. 2 Option 055 deletes the Data Logger function on Model N6705. 3 Only available when using the remote interfaces; not the front panel. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 9 Power Module Option Characteristics Option 760 & 761 Option 761 provides output and sense disconnect relays. Option 760 provides polarity reversal in addition to output and sense disconnect. Note that models N678xA SMU have output and sense disconnect relays built in. • Option 760 limits the output current to 10 A on Models N6742B and N6773A. + sense +S + rail + Option 761 - rail -S - sense • Option 760 is not available on Models N6741B, N6751A, N6752A, N6761A, N6762A, and N6781A – N6784A Although the plus and minus rail of the output power mesh are physically disconnected from the output terminals with options 760 and 761, a small AC network is still connected across the plus and minus output terminals (see figure). Option 054 Option 054 (High-speed Test Extensions) include output list and digitized measurement capability. This option is separately orderable for Models N673xB, N674xB, N677xA, and N675xA when installed in an N6700 MPS mainframes. All other power modules as well as the N6705 DC Power Analyzer mainframes have output list and digitized measurement capability built in. Output list: • Maximum number of steps = 512 • Maximum dwell time in seconds = 262 • Maximum list repetitions = 256 or infinite Digitized measurement: • Maximum measurement points = 4026 • Maximum sample rate = 50 kHz Option 2UA Option 2UA is a 200 microampere measurement range available on Models N6761A and N6762A only. It includes Option 761 relay capability. 10 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 2 Agilent N673xB, N674xB, N677xA DC Power Modules Performance Specifications ............................................................................ 12 Supplemental Characteristics ......................................................................... 14 Output Quadrant Characteristic ...................................................................... 16 Arbitrary Waveform Generator Maximum Bandwidth ................................ 16 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Agilent N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 11 Performance Specifications N6731B/ N6741B N6732B/ N6742B N6733B/ N6743B N6734B/ N6744B N6735B/ N6745B N6736B/ N6746B 0-5V 0-8V 0 - 20 V 0 - 35 V 0 - 60 V 0 - 100 V DC Output Ratings: Voltage NOTE 2 Current NOTE 1 0-10 A/ 0-20 A 0-6.25 A/0-12.5 A 0-2.5 A / 0-5 A 0-1.5 A / 0-3 A 0-0.8 A / 0-1.6 A 0-0.5 A / 0-1 A Power 50 W / 100 W 50 W / 100 W 50 W / 100 W 52.5W / 105W 50 W / 100 W 50 W / 100 W 10 mV / 20 mV 12 mV 14 mV 15 mV 25 mV 30 mV 2 mV 2 mV 3 mV 5 mV 9 mV 18 mV Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to- peak CV rms Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 5 mV 6 mV 9 mV 11 mV 13 mV / 16 mV 20 mV / 30 mV Current 2 mA 2 mA 2 mA 2 mA 2 mA 2 mA Source Effect (Regulation): Voltage 1 mV 2 mV 2 mV 4 mV 6 mV 10 mV Current 1 mA 1 mA 1 mA 1 mA 1 mA 1 mA Programming Accuracy: (@ 23 °C ±5 °C after a 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.1% + 19 mV 0.1% + 19 mV 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV Current 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 20 mA 0.15% + 10mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.1% + 20 mV 0.1% + 20 mV 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV Current 0.15% + 20 mA 0.15% + 10 mA 0.15% + 5 mA 0.15% + 4 mA 0.15% + 4 mA 0.15% + 2 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change from 50% to 100% and from 100% to 50% of full load.) Voltage settling band Time 12 NOTE 3 NOTE 3 ±0.08 V / 0.1 V ±0.08 V / 0.1 V ± 0.2 V / 0.3 V ± 0.2 V / 0.3 V ± 0.4 V / 0.5 V ± 0.5 V / 1.0 V < 200 µs < 200 µs < 200 µs < 200 µs < 200 µs < 200 µs N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Performance Specifications (continued) N6773A N6774A N6775A N6776A N6777A DC Output Ratings: Voltage 0 - 20 V 0 - 35 V 0 - 60 V 0 - 100 V 0 - 150 V 0 - 15 A NOTE 2 0 - 8.5 A 0-5A 0-3A 0-2A 300 W 300 W 300 W 300 W 300 W CV peak-to- peak 20 mV 22 mV 35 mV 45 mV 68 mV CV rms 3 mV 5 mV 9 mV 18 mV 27 mV Current NOTE 1 Power Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 13 mV 16 mV 24 mV 45 mV 68 mV Current 6 mA 6 mA 6 mA 6 mA 6 mA Voltage 2 mV 4 mV 6 mV 10 mV 15 mV Current 1 mA 1 mA 1 mA 1 mA 1 mA Source Effect (Regulation): Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV 0.1% +150 mV Current 0.15% + 60 mA 0.15% + 60 mA 0.15% + 60 mA 0.15% + 30 mA 0.15% + 30 mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.1% + 20 mV 0.1% + 35 mV 0.1% + 60 mV 0.1% +100 mV 0.1% +150 mV Current 0.15% + 15 mA 0.15% + 12 mA 0.15% + 12 mA 0.15% + 6 mA 0.15% + 6 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change from 50% to 100% and from 100% to 50% of full load.) Voltage settling band Time ± 0.3 V NOTE 4 ± 0.3 V NOTE 4 ± 0.5 V ± 1.0 V ± 2.0 V < 250 µs < 250 µs < 250 µs < 250 µs < 250 µs 1 Output current is derated 1% per °C above 40°C. 2 When relay option 760 is installed on Models N6742B and N6773A, the output current is limited to 10 A. 3 When relay option 760 or 761 is installed, the settling band is ±0.10V/0.125 V. Option 760 is not available on Model N6741B. 4 When relay option 760 or 761 is installed, the settling band is ±0.35 V. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 13 Supplemental Characteristics N6731B/ N6741B N6732B/ N6742B N6733B/ N6743B N6734B/ N6744B N6735B/ N6745B N6736B/ N6746B 15 mV – 5 .1 V 60 mA – 10.2 A/ 60 mA – 20.4 A 15 mV – 8 .16 V 40 mA –6.375 A/ 40 mA – 12.75 A 30 mV – 20.4 V 10 mA – 2.55 A/ 10 mA – 5.1 A 40 mV – 35.7 V 5 mA – 1.53 A/ 5 mA – 3.06 A 70 mV – 61.2 V 2.5 mA – 0.85 A/ 2.5 m A – 1.7 A 100 mV – 102 V 1.5 mA – 0.51A/ 1.5 mA – 1.02 A Voltage Current 3.5 mV 7 mA 4 mV 4 mA 7 mV 3 mA 10 mV 2 mA 18 mV 1 mA 28 mV 0.5 mA Voltage Current 3 mV 10 mA 4 mV 7 mA 10 mV 3 mA 18 mV 2 mA 30 mV 1 mA 50 mV 0.5 mA Voltage Current 0.005% + 0.1mV 0.005% + 1 mA 0.005% + 0.1 mV 0.005% + 0.5 mA 0.005% + 0.2 mV 0.005% + 0.1 mA 0.005% + 0.5 mV 0.005% + 0.05 mA 0.005% + 0.5 mV 0.005% + 0.02 mA 0.005% + 1 mV 0.005% + 0.02 mA Voltage Current 0.01% + 0.1mV 0.01% + 1 mA 0.01% + 0.1 mV 0.01% + 0.5 mA 0.01% + 0.2 mV 0.01% + 0.1 mA 0.01% + 0.2 mV 0.01% + 0.05 mA 0.01% + 0.5 mV 0.01% + 0.02 mA 0.01% + 0.5 mV 0.01% + 0.02 mA 0.1% + 30 mV 0.15% + 30 mA 0.15% + 40 mA 0.1% + 45 mV 0.15% + 15 mA 0.15% + 20 mA 0.1% + 75 mV 0.15% + 10 mA 0.15% + 14 mA 0.1% + 130 mV 0.15% + 9 mA 0.15% + 12 mA 0.1% + 190 mV 0.15% + 5 mA 0.15% + 7 mA 20 ms 20 ms 20 ms 20 ms 20 ms Programming Ranges: Voltage Current Programming Resolution: Measurement Resolution: Programming Temperature Coefficient per °C: Measurement Temperature Coefficient per °C: N6705 Mainframe Oscilloscope Measurement Accuracy: (@t 23 °C ±5 °C; accuracy of any individual point in the trace) Voltage 0.1% + 25 mV Current–Correction On NOTE 1 0.15% + 50 mA Current 0.15% + 70 mA Up-programming and Down-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion; for voltage setting from 0V to full scale and full scale to 0V) 20 ms Up-programming and Down-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full-scale value; for voltage setting from 0V to full scale and full scale to 0V) Over-voltage Protection: Accuracy Accuracy with Opt. 760 Accuracy with Opt. 761 Maximum setting Response time 100 ms 0.25% + 50mV 0.25%+600mV 0.25%+600mV 7.5 V Output Ripple and Noise (PARD): CC rms 100 ms 100 ms 100 ms 0.25% + 50 mV 0.25% + 75 mV 0.25% + 100 mV 0.25% + 200 mV 0.25% + 600 mV 0.25% + 350 mV 0.25% + 250 mV 0.25% + 300 mV 0.25% + 600 mV 0.25% + 350 mV 0.25% + 250 mV 0.25% + 300 mV 10 V 22 V 38.5 V 66 V 50 µs from occurrence of over-voltage condition to start of output shutdown 100 ms 0.25% + 250 mV 0.25% + 300 mV 0.25% + 300 mV 110 V 8 mA 4 mA 2 mA 2 mA 2 mA 2 mA 1 mA < 15 mA 1 mA < 10 mA 1 mA < 10 mA 1 mA < 10 mA 1 mA < 10 mA 1 mA < 10 mA 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) Rms Peak-to- peak 100 ms Outputs can maintain specifications with up to a 1-volt drop per load lead. Remote Sense The load lead drop reduces the maximum available voltage at the load. Capability: Identically rated outputs can be operated directly in parallel or can be connected for straight series operation. Series and Auto-series and auto-parallel operation is not available. Parallel Operation: Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay option With relay Option 760 14 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6773A N6774A N6775A N6776A N6777A Programming Ranges: Voltage 30 mV – 20.4 V 40 mV – 35.7 V 70 mV – 61.2 V 100 mV – 102 V 145 mV – 153 V Current 30 mA – 15.3 A 15 mA – 8.67 A 7.5 mA – 5.1 A 4.5 mA – 3.06 A 2.75 mA – 2.04 A Voltage 7 mV 10 mV 18 mV 28 mV 43 mV Current 9 mA 6 mA 3 mA 1.5 mA 1 mA Voltage 10 mV 18 mV 30 mV 50 mV 77 mV Current 9 mA 6 mA 3 mA 1.5 mA 1 mA Programming Resolution: Measurement Resolution: Programming Temperature Coefficient per °C: Voltage 0.01% + 0.2 mV 0.01% + 0.5 mV 0.01% + 0.5 mV 0.01% + 1 mV 0.01% + 1 mV Current 0.01% + 0.5 mA 0.01% + 0.5 mA 0.01% + 0.1 mA 0.01% + 0.1 mA 0.01% + 0.1 mA Measurement Temperature Coefficient per °C: Voltage 0.01% + 0.2 mV 0.01% + 0.2 mV 0.01% + 0.5 mV 0.01% + 0.5 mV 0.01% + 0.5 mV Current 0.01% + 0.5 mA 0.01% + 0.5 mA 0.01% + 0.05 mA 0.01% + 0.05 mA 0.01% + 0.05 mA N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C; accuracy of any individual point in the trace) Voltage 0.1% + 45 mV 0.1% + 75 mV 0.1% + 120 mV 0.1% + 160 mV Current – Correction On NOTE 1 0.15% + 35 mA 0.15% + 22 mA 0.15% + 19 mA 0.15% + 9 mA 0.1% + 175 mV 0.15% + 9 mA Current 0.15% + 45 mA 0.15% + 27 mA 0.15% + 22 mA 0.15% + 12 mA 0.15% + 12 mA Up-programming and Down-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion; for voltage setting from 0V to full scale and full scale to 0V) 20 ms 20 ms 20 ms 20 ms 20 ms Maximum Up-programming and Down-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full-scale value; for voltage setting from 0V to full scale and full scale to 0V) 100 ms 100 ms 100 ms 100 ms 100 ms Accuracy 0.25% +100 mV 0.25% + 130 mV 0.25% + 260 mV 0.25% + 650 mV 0.25% + 650 mV Accuracy with Opt. 761 0.25% + 500 mV 0.25% + 350 mV 0.25% + 350 mV 0.25% + 650 mV 0.25% + 650 mV Accuracy with Opt. 760 0.25% + 700 mV 0.25% + 700 mV 0.25% + 400 mV 0.25% + 650 mV 0.25% + 650 mV 22 V 38.5 V 66 V 110 V 165 V Over-voltage Protection: Maximum setting Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise (PARD): CC rms 6 mA 6 mA 6 mA 6 mA 6 mA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) Rms Peak-to- peak 2 mA 2 mA 2 mA 2 mA 2 mA < 20 mA < 20 mA < 20 mA < 20 mA < 20 mA Outputs can maintain specifications with up to a 1-volt drop per load lead. Remote Sense The load lead drop reduces the maximum available voltage at the load. Capability: Identically rated outputs can be operated directly in parallel or can be connected for straight series operation. Series and Auto-series and auto-parallel operation is not available. Parallel Operation: Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay option With relay Option 760 1 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms 32 ms 58 ms Correction On compensates for current flowing into the output capacitor during voltage transients. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 15 Output Quadrant Characteristic Voltage maximum power + rated voltage 0 + rated current Current Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in an Agilent N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting 6 dB max. = Max. frequency where the voltage drops to 6 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD 6 dB = The total harmonic distortion at 6 dB max. frequency Voltage 3 dB max THD 3 dB 6 dB max THD 6 dB N6731B & N6741B 0.1 Vp-p 175 Hz 1.0% 260 Hz 3.0% 0.1 Vp-p 125 Hz 1.0% 175 Hz 3.0% 0.3 Vp-p 75 Hz 6.0% 100 Hz 6.0% 0.5 Vp-p 40 Hz 9.0% 55 Hz 9.0% 5.0 Vp-p 20 Hz 10% 37 Hz 10% N6732B & N6742B 16 0.1 Vp-p 125 Hz 1.0% 200 Hz 3.0% 0.2 Vp-p 125 Hz 1.0% 180 Hz 3.0% 0.4 Vp-p 75 Hz 6.0% 100 Hz 6.0% 0.8 Vp-p 40 Hz 8.5% 60 Hz 8.5% 8.0 Vp-p 20 Hz 10% 37 Hz 10% N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Arbitrary Waveform Generator Maximum Bandwidth (continued) Voltage 3 dB max THD 3 dB 6 dB max THD 6 dB 3 dB max THD 3 dB N6733B & N6743B 6 dB max THD 6 dB N6773A 0.2 Vp-p 110 Hz 1.0% 190 Hz 3.0% 125 Hz 1.5% 210 Hz 4.0% 0.4 Vp-p 110 Hz 1.0% 160 Hz 3.0% 125 Hz 1.5% 180 Hz 4.0% 1.0 Vp-p 72 Hz 6.0% 95 Hz 6.0% 75 Hz 6.0% 95 Hz 6.0% 2.0 Vp-p 40 Hz 8.0% 55 Hz 8.5% 42 Hz 9.0% 60 Hz 9.0% 20 Vp-p 20 Hz 10% 37 Hz 10% 20 Hz 10% 37 Hz 10% N6734B & N6744B N6774A 0.4 Vp-p 125 Hz 1.0% 200 Hz 1.0% 125 Hz 1.0% 200 Hz 1.0% 0.7 Vp-p 125 Hz 1.0% 175 Hz 3.5% 125 Hz 1.0% 160 Hz 3.0% 1.8 Vp-p 72 Hz 6.0% 100 Hz 6.0% 75 Hz 6.0% 95 Hz 6.0% 3.5 Vp-p 40 Hz 8.0% 55 Hz 8.5% 40 Hz 8.5% 55 Hz 8.5% 35 Vp-p 20 Hz 8.0% 37 Hz 8.5% 20 Hz 10% 37 Hz 10% N6735B & N6745B N6775A 0.6 Vp-p 100 Hz 1.0% 180 Hz 1.0% 120 Hz 1.0% 200 Hz 1.0% 1.2 Vp-p 100 Hz 1.0% 160 Hz 3.0% 120 Hz 1.0% 160 Hz 3.0% 3.0 Vp-p 70 Hz 5.5% 92 Hz 5.5% 70 Hz 5.0% 95 Hz 6.0% 6.0 Vp-p 40 Hz 8.0% 55 Hz 8.0% 40 Hz 8.5% 55 Hz 8.5% 60 Vp-p 20 Hz 8.0% 37 Hz 8.0% 20 Hz 10% 35 Hz 10% N6736B & N6746B N6776A 1.0 Vp-p 90 Hz 1.0% 160 Hz 1.5% 75 Hz 1.0% 160 Hz 1.0% 2.0 Vp-p 90 Hz 1.0% 150 Hz 3.0% 75 Hz 1.0% 150 Hz 3.0% 5.0 Vp-p 62 Hz 4.5% 85 Hz 6.0% 55 Hz 4.0% 75 Hz 6.0% 10 Vp-p 37 Hz 8.0% 50 Hz 8.0% 35 Hz 8.0% 45 Hz 8.0% 100 Vp-p 20 Hz 8.0% 35 Hz 8.0% N/A N/A 35 Hz 8.0% N6777A 1.5 Vp-p 70 Hz 1.0% 150 Hz 1.0% 3.0 Vp-p 55 Hz 5.0% 120 Hz 2.0% 7.5 Vp-p 55 Hz 5.0% 70 Hz 6.0% 15 Vp-p 35 Hz 7.0% 55 Hz 7.0% 150 Vp-p N/A N/A 30 Hz 1.0% N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 17 Chapter 3 Agilent N675xA High Performance Power Modules Performance Specifications ............................................................................ 20 Supplemental Characteristics ......................................................................... 21 Autoranging Characteristic.............................................................................. 23 Output Impedance Graphs ............................................................................... 23 Arbitrary Waveform Generator Maximum Bandwidth ................................ 26 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Agilent N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 19 Performance Specifications N6751A/N6752A N6753A/N6755A N6754A/N6756A 0 - 50 V 0 - 20 V 0 - 60 V 0 - 5 A / 0 - 10 A 0 - 50 A 0 - 20 A / 0 - 17A 50 W / 100 W 300 W / 500 W 300 W / 500 W CV peak-to-peak 4.5 mV 5 mV 6 mV CV rms 0.35 mV 1 mV 1 mV DC Output Ratings: Voltage Current NOTE 1 Power Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 2 mV 2 mV 2 mV Current 2 mA 12 mA 5 mA Voltage 1 mV 0.5 mV 1.2 mV Current 1 mA 5 mA 2 mA Source Effect (Regulation): Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.06% + 19 mV 0.06% + 10 mV 0.06% + 25 mV Current 0.1% + 20 mA 0.1% + 30 mA 0.1% + 12 mA Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.05% + 20 mV 0.05% + 10 mV 0.05% + 25 mV Current 0.1% + 4 mA 0.1% + 30 mA 0.1% + 8 mA Load Transient Recovery Time: (Time to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60% of full load for model N6751A - from 50% to 100% and from 100% to 50% of full load for models N6752A through N6756A.) Voltage settling band Time ± 75 mV NOTE 2 ± 30 mV NOTE 3 ± 90 mV NOTE 4 < 100 µs < 100 µs < 100 µs 1 Output current is derated 1% per °C above 40°C. 2 When relay option 761 is installed on Model N6752A, the settling band is ±125 mV. 3 When relay option 760 or 761 is installed on Model N6753A and N6755A, the settling band is ±200 mV. 4 When relay option 760 or 761 is installed on Model N6754A and N6756A, the settling band is ±350 mV. 20 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6751A / N6752A N6753A / N6755A N6754A / N6756A Voltage 20 mV – 51 V 10 mV – 20.4 V 25 mV- 61.2 V Current 10 mA – 5.1A/10 mA – 10.2A 50 mA – 51 A 20 mA – 20.4 A/20 mA – 17.3A Voltage 3.5 mV 1.5 mV 4.2 mV Current 3.25 mA 16.3 mA 6.5 mA Voltage 1.8 mV 0.8 mV 2.2 mV Current 410 µA 2.05 mA 0.82 mA Voltage 18 ppm + 160 µV 35 ppm + 100 µV 35 ppm + 170 µV Current 100 ppm + 45 µA 60 ppm + 500 µA 60 ppm + 200 µA Programming Ranges: Programming Resolution: Measurement Resolution: Programming Temperature Coefficient per °C: Measurement Temperature Coefficient per °C: Voltage 25 ppm + 35 µV 50 ppm + 85 µV 50 ppm + 100 µV Current 60 ppm + 3 µA 60 ppm + 30 µA 60 ppm + 12 µA N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C, accuracy of any individual point in the trace) Voltage Current– with Correction On NOTE 1 Current 0.05% + 32 mV 0.05% + 15 mV 0.05% + 37 mV 0.1% + 14 mA N/A N/A 0.1% + 8 mA 0.1% + 52 mA 0.1% + 17 mA Up-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion) Small voltage step Time Large voltage step Time 0 V to 10 V 0 V to 6 V/0 V to 10 V 0 V to 15 V/0 V to 29 V 0.2 ms 0.4 ms/0.5 ms 0.35 ms/0.7 ms 0 V to 50 V 0 V to 20 V 0 V to 60 V 1.5 ms 1.5 ms 2 ms Up-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time 0 V to 10 V 0 V to 6 V/0 V to 10 V 0 V to 15 V/0 V to 29 V 0.5 ms 0.8 ms/1.0 ms 0.8 ms/1.4 ms 0 V to 50 V 0 V to 20 V 0 V to 60 V 4 ms 3 ms 4.2 ms Down-programming Time with no load: (Time from start of voltage change to output voltage < 0.5 V) Small voltage step Time Large voltage step Time 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 0.3 ms 0.55 ms/1.0 ms 0.6 ms/1.2 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 1.3 ms 1.8 ms 2.2 ms Down-programming Settling Time with no load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 0.45 ms 0.8 ms/1.3 ms 0.8 ms/1.5 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 1.4 ms 2 ms 2.3 ms 21 Supplemental Characteristics (continued) N6751A / N6752A N6753A / N6755A N6754A / N6756A Down-programming Time with Capacitive load: (Time from start of voltage change to output voltage < 0.5 V) Small voltage step 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 2.1 ms 2.2 ms/4.5 ms 2.3 ms/5.5 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 11 ms 8.5 ms 10 ms 1000 µF 4700 µF 680 µF Continuous power 7W 12.5 W 12.5 W Peak current 7A 15 A 6A Accuracy 0.25% + 0.25 V 0.25% + 0.15V 0.25% + 0.3V Accuracy with Option 761 0.25% + 0.25 V 0.25% + 0.45V 0.25% + 0.6V Accuracy with Option 760 N/A 0.25% + 0.45V 0.25% + 0.6V Maximum setting 55 V 22 V 66 V Time Large voltage step Time Capacitive load NOTE 2 Down-programming Capability: Over-voltage Protection: Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise: (PARD) CC rms: 2 mA 10 mA 4 mA 500 µA 750 µA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) rms peak-to-peak Remote Sense Capability: Series and Parallel Operation: 500 µA < 2 mA < 2 mA < 3 mA Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Identically rated outputs can be operated directly in parallel or be connected for straight series operation. Auto-series and auto-parallel operation is not available. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay option 25 ms 18 ms 18 ms With relay Option 760 51 ms 44 ms 44 ms 1 Correction On compensates for current flowing into the output capacitor during voltage transients. 2 Modules can discharge the specified capacitive load from full scale to 0V at a rate of 4 times/second. 22 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Autoranging Characteristic N6751A 50 W Output Voltage Voltage N6752A 100 W Output Voltage Voltage N6755A / N6756A 500 W Output 20 V 60 V 20 V 60 V 50 V 50 V N6753A / N6754A 300 W Output 500 W curve 6V 15 V 12 V Current 8.5 V 10 V 0 5A 1A 300 W curve 100 W curve 50 W curve 0 0 8.33 A 10 A Current Current Current 2A 10 V 29 V 15 A 5A 50 A 20 A 0 25 A 8.33 A 50 A 17 A Output Impedance Graphs Magnitude 4 90 2 45 Phase 1 0 0.5 -45 0.25 -90 PHASE (degrees) IMPEDANCE (ohms) 8 0.125 100 1k 10k FREQUENCY (Hz) 100k Model N6752A, CC Mode, @50V, 2A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 23 135 90 40 90 40 20 45 20 0 10 -45 5 -90 2.5 Phase 10 5 2.5 45 Phase -45 Magnitude Magnitude 1.25 1.25 0.62 0.62 100 1k 10k 100k 100 1k FREQUENCY (Hz) 10k 100k FREQUENCY (Hz) Model N6753A and N6755A, CV Mode, @20 V, 15A Model N6753A and N6755A, Option 760, CV Mode, @20 V, 15A 0.8 0.8 Magnitude IMPEDANCE (ohms) 0 Magnitude 0.4 0.4 Phase 90 Phase 45 0.2 45 0.1 0 0.1 0 0.05 -45 0.05 -45 0.025 -90 0.025 -90 0.0125 -135 0.0125 0.2 0.0062 100 0.0062 1k 10k FREQUENCY (Hz) 100k Model N6753A and N6755A, CC Mode, @20 V, 15A 24 PHASE (degrees) 80 100 1k 10k 100k FREQUENCY (Hz) Model N6753A and N6755A, Option 760, CC Mode, @20 V, 15A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide PHASE (degrees) IMPEDANCE (milliohms) 80 90 0.4 90 0.2 45 0.2 45 0.1 0 0.1 0 -45 0.05 0.05 Phase 0.025 -90 Magnitude 0.0125 Phase 0.025 -90 Magnitude 0.0125 0.0062 0.0062 100 1k 10k 100 100k 1k FREQUENCY (Hz) Model N6754A and N6756A, CV Mode, @60 V, 5A 10k FREQUENCY (Hz) 100k Model N6754A and N6756A, Option 760, CV Mode, @60 V, 5A 8 IMPEDANCE (ohms) -45 8 Magnitude Magnitude 4 4 45 2 Phase 45 2 Phase 0 1 0.5 -45 0.5 -45 0.25 -90 0.25 -90 0.125 -135 0.125 -135 1 0.062 0 0.062 100 1k 10k FREQUENCY (Hz) 100k Model N6754A and N6756A, CC Mode, @60 V, 5A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 100 1k 10k FREQUENCY (Hz) 100k Model N6754A and N6756A, Option 760, CC Mode, @60 V, 5A 25 PHASE (degrees) IMPEDANCE (ohms) 0.4 PHASE (degrees) 0.8 0.8 Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in an Agilent N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD < 1.5% = The frequency below which the THD is less than 1.5%. Voltage 3 dB max THD 3 dB THD < 1.5% N6751A & N6752A 0.5 Vp-p 4000 Hz 12% 440 Hz 1.0 Vp-p 2200 Hz 21% 440 Hz 2.5 Vp-p 900 Hz 25% 265 Hz 5.0 Vp-p 500 Hz 27% 160 Hz 50.0 Vp-p 340 Hz 22% 25 Hz N6753A & N6755A 0.2 Vp-p 2300 Hz 10% 1300 Hz 0.4 Vp-p 1500 Hz 15% 800 Hz 1.0 Vp-p 980 Hz 19% 480 Hz 2.0 Vp-p 580 Hz 21% 300 Hz 20.0 Vp-p 400 Hz 12% 32 Hz N6754A & N6756A 26 0.6 Vp-p 2800 Hz 8.0% 1600 Hz 1.2 Vp-p 1400 Hz 15% 800 Hz 3.0 Vp-p 600 Hz 17% 300 Hz 6.0 Vp-p 400 Hz 20% 200 Hz 60.0 Vp-p 344 Hz 12% 30 Hz N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 4 Agilent N676xA Precision Power Modules Performance Specifications ............................................................................ 28 Supplemental Characteristics ......................................................................... 29 Autoranging Characteristic.............................................................................. 31 Output Impedance Graphs ............................................................................... 31 Arbitrary Waveform Generator Maximum Bandwidth ................................ 34 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Agilent N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 27 Performance Specifications DC Ratings: Voltage Current NOTE 1 Power Low programming ranges (V & I) Low measurement ranges (V & I) N6761A/N6762A N6763A/N6765A N6764A/N6766A 0 - 50 V 0 - 1.5 A / 0 - 3 A 0 - 20 V 0 - 50 A 0 - 60 V 0 - 20 A / 0 - 17 A 50 W / 100 W 5.5 V; 100 mA 5.5 V; 100 mA 300 W / 500 W N/A 2 V; 1.5 A 300 W / 500 W N/A 6 V; 0.5 A 4.5 mV 0.35 mV 5 mV 1 mV 6 mV 1 mV 2 mV 12 mA 2 mV 5 mA 0.5 mV 5 mA 1.2 mV 2 mA Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to-peak CV rms Load Effect (Regulation): (Applies for any output load change, with a maximum load-lead drop of 1V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 0.5 mV Current 30 µA (@ 0 –7 V) 65 µA (@ 7 – 50V) Source Effect (Regulation): Voltage Current 0.5 mV 30 µA Programming Accuracy: (@ 23 °C ±5 °C after 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage, high range 0.016% + 6 mV 0.03% + 5 mV 0.03% + 12 mV Voltage, low range 0.016% + 1.5 mV N/A N/A Current, high range 0.1% + 15 mA 0.075% + 4 mA 0.04% + 200 µA Current, low range 0.04% + 30 µA (@ 0 –7 V) N/A N/A 0.04% + 55 µA (@ 7 –50 V) Voltmeter/Ammeter Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring 4096 data points with a 20.48 μs time interval.) Voltage, high range Voltage, low range Current, high range Current, low range 200 µA current range (Option 2UA) 0.016% + 6 mV 0.016% + 1.5 mV 0.04% + 160 µA 0.03% + 15 µA (@ 0 – 7 V) 0.03% + 55 µA (@ 7 – 50 V) 0.5% + 100 nA 0.03% + 10 mV 0.03% + 1.5 mV 0.1% + 10 mA 0.05% + 1.1 mA NOTE 2 0.03% + 25 mV 0.03% + 5 mV 0.1% + 5 mA 0.05% + 0.75 mA NOTE 2 N/A N/A Load Transient Recovery Time: (time to recover to within the settling band following a load change - from 60% to 100% and from 100% to 60% of full load for model N6761A - from 50% to 100% and from 100% to 50% of full load for model N6762A through N6766A) Voltage settling band ± 75 mV ± 30 mV NOTE 3 ± 90 mV NOTE 4 Time < 100 µs < 100 µs < 100 µs 1 Output current is derated 1% per °C above 40°C. 2 Applies when measuring currents that remain within the low range. Due to thermal settling, when transitioning from measuring full-rated output current (the worst case), to measuring the current within the low range, the low range accuracy specification is typically met within 5 seconds after the current has transitioned into the low range. Accuracies within this 5 second settling period are typically 2X the specified accuracy or better. 3 When relay option 760 or 761 is installed on Models N6763Aand N6765A, the settling band is ±200 mV. 4 When relay option 760 or 761 is installed on Models N6764Aand N6766A, the settling band is ±350 mV. 28 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6761A / N6762A N6763A / N6765A N6764A / N6766A Voltage, high range 15 mV – 51 V 10 mV – 20.4 V 25 mV- 61.2 V Voltage, low range 12 mV – 5.5 V N/A N/A Current, high range 1 mA – 1.53 A/1 mA – 3.06 A 50 mA – 51 A 20 mA – 20.4A/20 mA – 17.3A Current, low range 0.1 mA – 0.1 A NOTE 1 N/A N/A 880 µV 1.5 mV 4.2 mV Programming Ranges: Programming Resolution: Voltage, high range Voltage, low range 90 µV N/A N/A Current, high range 60 µA 16.3 mA 6.5 mA Current, low range 2 µA N/A N/A 440 µV 250 µV 600 µV Measurement Resolution: Voltage, high range Voltage, low range 44 µV 25 µV 60 µV Current, high range 30 µA 500 µA 250 µA Current, low range 1 µA 20 µA 10 µA 200 µA current range (Option 2UA) 4 nA N/A N/A 18 ppm + 140 µV 23 ppm + 95 µV 23 ppm + 218 µV Programming Temperature Coefficient per °C: Voltage, high range Voltage, low range 40 ppm + 70 µV N/A N/A Current, high range 33 ppm + 10 µA 25ppm + 129 µA 25ppm + 52 µA Current, low range 60 ppm + 1.5 µA N/A N/A 23 ppm + 53 µV 23 ppm + 73 µV Measurement Temperature Coefficient per °C: Voltage, high range 23 ppm + 40 µV Voltage, low range 30 ppm + 40 µV 25 ppm + 53 µV 25 ppm + 73 µV Current, high range 40 ppm + 0.3 µA 25 ppm + 21 µA 25 ppm + 7 µA 50 ppm + 0.3 µA 27 ppm + 21 µA 27 ppm + 7 µA 100 ppm + 3 nA/°C N/A N/A Current, low range Current, 200 µA range (Option 2UA) N6705 Mainframe Oscilloscope Measurement Accuracy: (@ 23 °C ±5 °C, accuracy of any individual point in the trace) Voltage Current, high range – with Correction On 0.016% + 16 mV 0.04% + 10 mA 0.03% + 13 mV 0.03% + 32 mV N/A N/A Current, high range 0.04% + 1 mA 0.1% + 16 mA 0.1% + 8.4 mA Current, low range 0.03% + 0.175 mA 0.05% + 6.6 mA 0.05% + 2.6 mA NOTE 2 Up-programming Time with full resistive load: (Time from 10% to 90% of total voltage excursion) Small voltage step Time Large voltage step Time 0 V to 10 V 0 V to 6 V/0 V to 10 V 0 V to 15 V/0 V to 29 V 0.6 ms 0.4 ms/0.5 ms 0.35 ms/0.7 ms 0 V to 50 V 0 V to 20 V 0 V to 60 V 2.2 ms 1.5 ms 2 ms Up-programming Settling Time with full resistive load: (Time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 0 V to 10 V 0 V to 6 V/0 V to 10 V 0 V to 15 V/0 V to 29 V 0.9 ms 0.8 ms/1.0 ms 0.8 ms/1.4 ms 0 V to 50 V 0 V to 20 V 0 V to 60 V 4 ms 3 ms 4.2 ms 29 Supplemental Characteristics (continued) N6761A / N6762A N6763A / N6765A N6764A / N6766A Down-programming Time with no load: (time from start of voltage change to output voltage < 0.5 V) Small voltage step Time Large voltage step Time 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 0.3 ms 0.55 ms/1.0 ms 0.6 ms/1.2 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 1.3 ms 1.8 ms 2.2 ms Down-programming Settling Time with no load: (time from start of voltage change to 0.1% of full scale value) Small voltage step Time Large voltage step Time 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 0.45 ms 0.8 ms/1.3 ms 0.8 ms/1.5 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 1.4 ms 2 ms 2.3 ms Down-programming Time with Capacitive load: (time from start of voltage change to output voltage < 0.5 V) Small voltage step Time Large voltage step Time 10 V to 0 V 6 V to 0 V/10 V to 0 V 15 V to 0 V/29 V to 0 V 4.5 ms 2.2 ms/4.5 ms 2.3 ms/5.5 ms 50 V to 0 V 20 V to 0 V 60 V to 0 V 23 ms 8.5 ms 10 ms 1000 µF 4700 µF 680 µF Continuous power 7W 12.5 W 12.5 W Peak current 3.8 A 15 A 6A Accuracy 0.25% + 0.25 V 0.25% + 0.15 V 0.25% + 0.3 V Accuracy with Option 761 0.25% + 0.25 V 0.25% + 0.45 V 0.25% + 0.6 V Accuracy with Option 760 N/A 0.25% + 0.45 V 0.25% + 0.6 V 55 V 22 V 66 V Capacitive load NOTE 3 Down-programming Capability: Over-voltage Protection: Maximum setting Response time 50 µs from occurrence of over-voltage condition to start of output shutdown Output Ripple and Noise: (PARD) CC rms: 2 mA 10 mA 4 mA 500 µA 750 µA Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis) rms peak-to-peak Remote Sense Capability: Series and Parallel Operation: 500 µA < 2 mA < 2 mA < 3 mA Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Identically rated outputs can be operated directly in parallel or be connected for straight series operation. Auto-series and auto-parallel operation is not available. Minimum Output Turn-On Delay: (Time from when any Output On command is received until the output starts turning on) Without relay option With relay Option 760 32 ms NOTE 4 18 ms 18 ms 44 ms 58 If you are operating the unit below 255 µA in constant current mode, the output may become unregulated with the following load conditions: The load resistance is <175 mΩ and the load inductance is >20 µH. If this occurs, an UNRegulated flag will be generated and the output current may rise above the programmed value but will remain less than 255 µA. 2 Correction On compensates for current flowing into the output capacitor during voltage transients 3 Modules can discharge the specified capacitive load from full scale to 0V at a rate of 4 times/second. 4 In Current priority mode, minimum delay is 23 ms without relays and 45 ms with relay Option 760. ms NOTE 4 44 ms 1 30 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Autoranging Characteristic Voltage N6761A / N6762A 50 W / 100 W Output Voltage N6763A / N6764A 300 W Output N6765A / N6766A 500 W Output 20 V 60 V 20 V 60 V 50 V Voltage 500 W curve 33 V 300 W curve 6V 15 V 1 A 1.5 A - 50 W 2 A 3 A - 100 W Current Current Current 0 10 V 29 V 0 15 A 5A 50 A 20 A 0 25 A 8.33 A 50 A 17 A Output Impedance Graphs 320 80 135 40 90 20 45 10 0 5 Phase Magnitude 2.5 1k 100 10k FREQUENCY (Hz) PHASE (degrees) IMPEDANCE (milliohms) 160 -45 100k Model N6762A, CV Mode, @50V, 2A Magnitude 4 90 2 45 Phase 1 0 0.5 -45 0.25 -90 PHASE (degrees) IMPEDANCE (ohms) 8 0.125 100 1k 10k FREQUENCY (Hz) 100k Model N6762A, CC Mode, @50V, 2A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 31 135 90 40 90 40 20 45 20 0 10 -45 5 -90 2.5 Phase 10 5 2.5 45 Phase -45 Magnitude Magnitude 1.25 1.25 0.62 0.62 100 1k 10k 100k 100 1k FREQUENCY (Hz) 10k 100k FREQUENCY (Hz) Model N6763A and N6765A, CV Mode, @20 V, 15A Model N6763A and N6765A, Option 760, CV Mode, @20 V, 15A 0.8 0.8 Magnitude IMPEDANCE (ohms) 0 Magnitude 0.4 0.4 Phase 90 Phase 45 0.2 45 0.1 0 0.1 0 0.05 -45 0.05 -45 0.025 -90 0.025 -90 0.0125 -135 0.0125 0.2 0.0062 100 0.0062 1k 10k FREQUENCY (Hz) 100k Model N6763A and N6765A, CC Mode, @20 V, 15A 32 PHASE (degrees) 80 100 1k 10k 100k FREQUENCY (Hz) Model N6763A and N6765A, Option 760, CC Mode, @20 V, 15A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide PHASE (degrees) IMPEDANCE (milliohms) 80 90 0.4 90 0.2 45 0.2 45 0.1 0 0.1 0 -45 0.05 0.05 Phase 0.025 -90 Magnitude 0.0125 Phase 0.025 -90 Magnitude 0.0125 0.0062 0.0062 100 1k 10k 100 100k 1k FREQUENCY (Hz) Model N6764A and N6766A, CV Mode, @60 V, 5A 10k FREQUENCY (Hz) 100k Model N6764A and N6766A, Option 760, CV Mode, @60 V, 5A 8 IMPEDANCE (ohms) -45 8 Magnitude Magnitude 4 4 45 2 Phase 45 2 Phase 0 1 0.5 -45 0.5 -45 0.25 -90 0.25 -90 0.125 -135 0.125 -135 1 0.062 0 0.062 100 1k 10k FREQUENCY (Hz) 100k Model N6764A and N6766A, CC Mode, @60 V, 5A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 100 1k 10k FREQUENCY (Hz) 100k Model N6764A and N6766A, Option 760, CC Mode, @60 V, 5A 33 PHASE (degrees) IMPEDANCE (ohms) 0.4 PHASE (degrees) 0.8 0.8 Arbitrary Waveform Generator Maximum Bandwidth NOTE The information in this section only applies when the power modules are installed in an Agilent N6705 DC Power Analyzer. The following tables characterize the maximum bandwidth of the arbitrary waveform generator. The maximum bandwidth is based on a sine wave into a resistive load and apples to any output current. The following definitions apply in the frequency tables: V p-p = Voltage peak-to-peak 3 dB max. = Max. frequency where the voltage drops to 3 dB below its setting THD 3 dB = The total harmonic distortion at 3 dB max. frequency THD < 1.5% = The frequency below which the THD is less than 1.5%. Voltage 3 dB max THD 3 dB THD < 1.5% N6761A & N6762A 0.5 Vp-p 4500 Hz 14% 450 Hz 1.0 Vp-p 3600 Hz 14% 450 Hz 2.5 Vp-p 1300 Hz 25% 340 Hz 5.0 Vp-p 600 Hz 25% 250 Hz 50.0 Vp-p 350 Hz 22% 30 Hz N6763A & N6765A 0.2 Vp-p 2300 Hz 10% 1300 Hz 0.4 Vp-p 1500 Hz 15% 800 Hz 1.0 Vp-p 980 Hz 19% 480 Hz 2.0 Vp-p 580 Hz 21% 300 Hz 20.0 Vp-p 400 Hz 12% 32 Hz N6764A & N6766A 34 0.6 Vp-p 2800 Hz 8.0% 1600 Hz 1.2 Vp-p 1400 Hz 15% 800 Hz 3.0 Vp-p 600 Hz 17% 300 Hz 6.0 Vp-p 400 Hz 20% 200 Hz 60.0 Vp-p 344 Hz 12% 30 Hz N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 5 Agilent N6781A, N6782A, N6784A Source/Measure Units Performance Specifications ............................................................................ 36 Supplemental Characteristics ......................................................................... 37 Output Quadrant Characteristic ...................................................................... 42 Output Impedance Graphs ............................................................................... 42 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 30°C after a 30-minute warm-up period. Unless otherwise noted, specifications apply at the mainframe output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Agilent N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 35 Performance Specifications DC Ratings: Voltage Current NOTE 1 Power Auxiliary Voltage Measurement Input: N6781A N6782A N6784A 20 V / 6 V ±1A/±3A 20 W ± 20 V 20 V / 6 V ±1A/±3A 20 W N/A ± 20 V / ± 6 V ±1A/±3A 20 W N/A 12 mV 1.2 mV 12 mV 1.2 mV 12 mV 1.2 mV Output Voltage Ripple & Noise (PARD) from 20 Hz – 20 MHz: (Measured at front panel terminals, with full load, in Voltage Priority mode. Output Bandwidth setting = Low) CV peak-to-peak CV rms Load Effect (Load regulation): (For any load change, based on a load lead drop 1.0 V. The load lead drop reduces the maximum available voltage at the load.) Voltage, 20 V range 700 μV 700 μV 700 μV Voltage, 6 V range 400 μV 400 μV 400 μV Current, 3 A range 100 μA 100 μA 100 μA Current, 1 A range 50 μA 50 μA 50 μA Current 300 mA range 50 μA 50 μA N/A Current 100 mA & 10 mA range NOTE 2 N/A N/A 1 μA Source Effect (Line regulation): Voltage, all ranges Current, all ranges Programming Accuracy @ 23 °C ±5 °C: 300 μV 60 μA 300 μV 60 μA (After a 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage, 20 V range 0.025% + 1.8 mV 0.025% + 1.8 mV Voltage, 6V range 0.025% + 600 μV 0.025% + 600 μV Voltage 600 mV range NOTE 2 0.025% + 200 μV 0.025% + 200 μV Current 3 A & 1 A range 0.04% + 300 μA 0.04% + 300 μA Current 300 mA range NOTE 2 0.03% + 150 μA 0.03% + 150 μA Current 100 mA range NOTE 2 N/A N/A Current 10 mA range NOTE 2 N/A N/A Resistance for 20 V, 1 A output range 0.1% + 3 mΩ N/A Resistance for 6 V, 3 A output range 0.1% + 1.5 mΩ N/A Measurement Accuracy @ 23 °C ±5 °C: (Applies when measuring the default value of 4883 data points with a 20.48 μs time interval.) Voltage 20 V range Voltage 1 V range Voltage 100 mV range Current 3 A range Current 100 mA range Current 1 mA range NOTE 3 Current 10 μA range NOTE 3 Auxiliary Voltage Measurement Input 0.025% + 1.2 mV 0.025% + 75 μV 0.025% + 50 μV 0.03% + 250 μA 0.025% + 10 μA 0.025% + 100 nA (110 nA) 0.025% + 8 nA (20 nA) 0.025% + 5 mV Load Transient Response Time in Voltage Priority mode: 0.025% + 1.2 mV 0.025% + 75 μV 0.025% + 50 μV 0.03% + 250 μA 0.025% + 10 μA 0.025% + 100 nA (110 nA) 0.025% + 8 nA (20 nA) N/A 300 μV 60 μA 0.025% + 1.8 mV 0.025% + 600 μV 0.025% + 200 μV 0.04% + 300 μA N/A 0.03% + 12 μA 0.025% + 5 μA N/A N/A 0.025% + 1.2 mV 0.025% + 75 μV 0.025% + 50 μV 0.03% + 250 μA 0.025% + 10 μA 0.025% + 100 nA (110 nA) 0.025% + 8 nA (20 nA) N/A (Time to recover to within settling band for a load change from 0.1 A to 0.9 A in the 20 V range; from 0.1 A to 1.5 A in the 6 V range.) Settling band for 20 V, 1 A output range ± 10 mV ± 10 mV ± 10 mV Settling band for 6 V, 3 A output range ± 20 mV ± 20 mV ± 20 mV Recovery time ≤ 35 μs ≤ 35 μs ≤ 35 μs 1 Output current is derated 1% per °C above 30°C. 2 600 mV range is only available in Voltage Priority mode; 300 mA, 100 mA, 10 mA ranges are only available in Current Priority mode. 3 Values in parentheses apply when power modules are installed in Agilent N6705A mainframes. 36 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6781A, N6782A N6784A Minimum current limit for 20 V range in Voltage Priority mode 10 mA 10 mA Minimum current limit for 6 V range in Voltage Priority mode 20 mA 20 mA Minimum voltage limit for 3 A range in Current Priority mode 10 mV 10 mV Minimum voltage limit for 1 A range in Current Priority mode 20 mV 20 mV 0 to 20.4 V; 200 μV -20.4 V to 20.4 V; 200 μV Minimum Current and Voltage Compliance limits: Programming Range & Resolution: Voltage, 20 V range Voltage, 6 V range 0 to 6.12 V; 60 μV -6.12 V to 6.12 V; 60 μV Voltage, 600 mV range 0 to 612 mV; 6 μV -612 mV to 612 mV; 6 μV Current, 3 A range -3.06 A to 3.06 A; 50 μA -3.06 A to 3.06 A; 50 μA Current, 1 A range -1.02 A to 1.02 A; 50 μA -1.02 A to 1.02 A; 50 μA Current, 300 mA range -306 mA to 306 mA; 3 μA N/A Current, 100 mA range N/A -102 mA to 102 mA; 1 μA Current, 10 mA range N/A -10.2 mA to 10.2 mA; 0.1 μA Resistance, for 20 V / 1 A range (N6781A only) -40mΩ to +1Ω; 0.5mΩ Resistance, for 6 V / 3 A range (N6781A only) -40mΩ to +1Ω; 0.25mΩ Programming Accuracy Temperature Coefficient (per °C): Voltage, 20 V range 0.002% +120uV 0.002% +120uV Voltage, 6 V range 0.0015% +40uV 0.0015% +40uV Voltage, 600 mV range 0.0015% +10uV 0.0015% +10uV Current, 3 A range 0.0025% +22uA 0.0025% +22uA Current, 1 A range 0.0025% +22uA 0.0025% +22uA Current, 300 mA range 0.0025% +14uA N/A Current, 100 mA range N/A 0.0025% +1uA Current, 10 mA range N/A 0.0025% +0.5 μA Voltage, 20 V range 200 μV 200 μV Voltage, 1 V range 10 μV 10 μV Voltage, 100 mV range 1 μV 1 μV Current, 3 A range 50 μA 50 μA Measurement Resolution: Current, 100 mA range 1 μA 1 μA Current, 1 mA range 10 nA 10 nA Current, 10 μA range 0.1 nA 0.1 nA Auxiliary Voltage Measurement Input (N6781A only) 800 μV N/A Voltage, 20 V range 0.0025% +25 uV 0.0025% +25 uV Voltage, 1 V range 0.002% +2.5 uV 0.002% +2.5 uV Voltage, 100 mV range 0.0025% +2.5 uV 0.0025% +2.5 uV Measurement Accuracy Temperature Coefficient (per °C): N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 37 Supplemental Characteristics (continued) N6781A, N6782A N6784A 0.0025% +14 uA 0.0025% +0.4 uA 0.002% +5 nA 0.002% +0.55 nA 0.0007% +200 uV 0.0025% +14 uA 0.0025% +0.4 uA 0.002% +5 nA 0.002% +0.55 nA N/A Measurement Accuracy Temperature Coefficient (continued) Current, 3 A range Current, 100 mA range Current, 1 mA range Current, 10 μA range Auxiliary Voltage Measurement Input (N6781A only) Voltage Programming Speed & Settling Time: At the specified Bandwidth setting. Low High1 High2 High3 Low High1 High2 High3 Rise Time (from 10% to 90% of step) 20 V range with a 0-10 V step 6 V range with a 0-4 V step 600mV range with a 0-500 mV step 300 μs 15 μs 20 μs 120 μs 300 μs 15 μs 20 μs 120 μs 300 μs 20 μs 22 μs 50 μs 300 μs 20 μs 22 μs 50 μs 400 μs 75 μs 30 μs 50 μs 400 μs 75 μs 30 μs 50 μs Settling Time (to 0.1% of step) 20 V range with a 0-10 V step 6 V range with a 0-4 V step 600mV range with a 0-500 mV step 850 μs 45 μs 65 μs 240 μs 850 μs 45 μs 65 μs 240 μs 850 μs 55 μs 65 μs 160 μs 850 μs 55 μs 65 μs 160 μs 1.2 ms 220 μs 85 μs 170 μs 1.2 ms 220 μs 85 μs 170 μs High Frequency Output Voltage Noise: At the specified Bandwidth setting. Low High1 High2 High3 Low High1 High2 High3 CV peak-to-peak (from 20 Hz – 20 MHz;) 20 V range with no load 6 V & 600 mV range with no load 12 mV 12 mV 4 mV 4 mV 12 mV 12 mV 4 mV 12 mV 12 mV 4 mV 3 mV 12 mV 12 mV 4 mV CV rms (from 20 Hz – 20 MHz;) 20 V range with no load 6 V & 600 mV range with no load 1.2 mV 1.2 mV 0.5 mV 0.5 mV 1.2 mV 1.2 mV 0.5 mV 0.5 mV 1 mV 1 mV 0.3 mV 0.3 mV 1 mV 1 mV 0.3 mV 0.3 mV 4 mV 3 mV Low Frequency Output Voltage Noise: CV peak to peak (from 0.1 Hz – 10 Hz) 20 V range 6 V range 600 mV range N/A N/A N/A 100 μV 50 μV 20 μV CV rms (from 0.1 Hz – 10 Hz) 20 V range 6 V range 600 mV range N/A N/A N/A 20 μV 10 μV 5 μV Voltage Programming Small Signal Bandwidth: (All ranges) At the specified Bandwidth setting. Low High1 High2 High3 Low High1 High2 High3 3 dB typical with no load cap with 1μF load cap with 6.8μF load cap with 150μF load cap DC to 1.4 kHz 29 kHz DC to N/A 60 kHz N/A N/A DC to DC to 2.9 kHz N/A N/A N/A 1.4 kHz 29 kHz 21 kHz N/A N/A 60 kHz 40 kHz 8.6 kHz N/A N/A N/A 14 kHz 2.9 kHz N/A N/A N/A 21 kHz N/A 40 kHz 8.6 kHz N/A 14 kHz 1 dB typical with no load cap with 1μF load cap with 6.8μF load cap with 150μF load cap DC to 700 Hz DC to N/A N/A DC to DC to 1 kHz N/A N/A 700 Hz 11 kHz N/A N/A 14 kHz 4.3 kHz N/A N/A 6 kHz 1 kHz N/A N/A 11 kHz N/A 14 kHz 4.3 kHz N/A 6 kHz 38 15 kHz 22 kHz N/A N/A 15 kHz 22 kHz N/A N/A N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6781A, N6782A N6784A 3 mV 250 μV 50 μV 3 mV 250 μV 50 μV 40 μs 40 μs 3 db typical with seamless ranging Off with seamless ranging On DC to 30 kHz DC to 27 kHz DC to 30 kHz N/A 1 db typical with seamless ranging Off with Seamless ranging On DC to 17 kHz DC to 15 kHz DC to 17 kHz N/A 10 MΩ ± 60 V ± 240 VDC 100k samples/second N/A N/A N/A N/A Voltage Measurement Noise: Peak value 20 V range 1 V range 100 mV range Voltage Measurement Settling Time: (All ranges) Settling Time with no range change Voltage Measurement Small Signal Bandwidth: (All ranges) Auxiliary Voltage Measurement Input: (N6781A only) Differential input resistance Maximum continuous differential input without damage Maximum voltage from chassis common Maximum conversion rate Voltage Priority Transient Characteristic: (6 V range only) At the specified Bandwidth setting. Low High1 High2 High3 Low High1 High2 High3 At the specified Settling band. 40 mV 50 mV 30 mV 20 mV 40 mV 50 mV 30 mV 20 mV Recovery time with no load cap with 1μF load cap with 6.8μF load cap with 150μF load cap 30 μs N/A N/A 140 μs 10 μs N/A N/A 30 μs 20 μs 10 μs N/A N/A N/A 25 μs 15 μs N/A N/A N/A 35 μs 140 μs 10 μs N/A N/A 20 μs 10 μs N/A N/A 25 μs 15 μs N/A N/A 35 μs Current Programming Speed & Settling Time: Rise Time (from 10% to 90% of step) 3 A range with a 0-3 A step 1 A range with a 0-1 A step 300 mA range with a 0-300mA step 100 mA range with a 0-100mA step 10 mA range with a 0-10mA step 2.8 μs 3.2 μs 3.5 μs N/A N/A 2.8 μs 3.2 μs N/A 4 μs 5 μs Settling Time (to 0.1% of step) 3 A range with a 0-3 A step 1 A range with a 0-1 A step 300 mA range with a 0-300mA step 100 mA range with a 0-100mA step 10 mA range with a 0-10mA step 30 μs 30 μs 40 μs N/A N/A 30 μs 30 μs N/A 30 μs 30 μs 200 μA 200 μA N/A N/A 2 μA 50 nA High Frequency Output Current Noise: (All ranges) CC rms (from 20 Hz – 20 MHz;) Low Frequency Output Current Noise: CC rms (from 0.1 Hz – 10 Hz) 3 A & 1 A ranges 100 mA range N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 39 Supplemental Characteristics (continued) N6781A, N6782A N6784A 3 dB - for all except 100 mA & 10 mA ranges - for 100 mA & 10 mA ranges DC to 120 kHz N/A DC to 120 kHz DC to 100 kHz 1 dB - for all except 100 mA & 10 mA ranges - for 100 mA & 10 mA ranges DC to 75 kHz N/A DC to 75 kHz DC to 50 kHz 400 μA 20 μA 2 μA 20 nA 400 μA 20 μA 2 μA 20 nA Settling Time with no range change or when up-ranging 3 A range 100 mA range 1 mA range 10 μA range (up- ranging N/A) 45 μs 45 μs 0.5 ms 1.5 ms 45 μs 45 μs 0.5 ms 1.5 ms Settling Time when down-ranging down-ranging to 100 mA range down-ranging to 1 mA range down-ranging to 10 μA range 45 μs 200 μs 3.5 ms 45 μs 200 μs 3.5 ms Current Programming Small Signal Bandwidth: (All ranges) Current Measurement Noise: Peak value 3 A range 100 mA 1 mA 10 μAl Current Measurement Settling Time: Current Measurement Small Signal Bandwidth: NOTE 1 3 dB typical with seamless ranging Off 3 A range 100 mA range 1 mA range 10 μA range DC DC DC DC 3 dB typical with seamless ranging On 3 A range 100 mA range 1 mA range 10 μA range DC to 26 kHz DC to 26 kHz DC to 10 kHz N/A N/A N/A N/A N/A 1 dB typical with seamless ranging Off 3 A range 100 mA range 1 mA range 10 μA range DC to 16 kHz DC to 16 kHz DC to 6 kHz DC to 400 Hz DC to 16 kHz DC to 16 kHz DC to 6.5 kHz DC to 400 Hz 1 dB typical with seamless ranging On 3 A range 100 mA range 1 mA range 10 μA range DC to 14 kHz DC to 14 kHz DC to 6 kHz N/A N/A N/A N/A N/A to 29 kHz to 29 kHz to 10 kHz to 750 Hz DC DC DC DC to 27 kHz to 27 kHz to 10 kHz to 750 Hz Common Mode Current from 20 Hz – 20 MHz: (With −output connected to chassis) CC peak-to-peak < 1 mA < 1 mA CC rms <100 μA <100 μA 40 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6781A, N6782A N6784A 0.05% + 20 mV 0.05% + 20 mV 24 V 24 V <30 s <30 s 1 V to 4 V 1 V to 4 V Over-voltage Protection: Accuracy Maximum setting Response time (From occurrence of over-voltage to start of shutdown) Current Priority Transient Characteristic: (3 A range) Voltage step Current settling band 5 mA 5 mA Recovery time NOTE 2 12 μs (24 μs) 2 12 μs (24 μs) 0.5 V to 20 V 0.5 V to 20 V Current Priority Transient Characteristic: (1 A range) Voltage step Current settling band 10 mA 10 mA Recovery time NOTE 2 12 μs (24 μs) 12 μs (24 μs) Remote Sense Capability: Outputs can maintain specifications with up to a 1-volt drop per load lead. The load lead drop reduces the maximum available voltage at the load. Series and Parallel Operation: Not supported Minimum Output Turn-on Delay: (Time from when any Output On command is received until the output starts turning on.) With output turn-off mode set to Low impedance 25.6 ms 25.6 ms With output turn-off mode set to High impedance 24.7 ms 24.7 ms 1 When using an Agilent N6705A mainframe and connecting through the front panel binding posts, additional output capacitance causes large measurement peaking/overshoots when the load impedance is greater than ~1 kΩ. This does not apply to Agilent N6705B mainframes. When using an N6705A or N6705B mainframe and connecting directly to the module connector, there are slight measurement peaking/overshoots when the load impedance is greater than ~10 kΩ. 2 Values in parentheses apply when power modules are installed in Agilent N6705A mainframes. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 41 Output Quadrant Characteristic Voltage N6781A, N8782A, 20 W Voltage +1 A +20 V N6784A, 20 W +20 V +3 A +6 V +6 V Current -3 A -1 A 0 +1 A +3 A Current 0 -6 V -3 A Key Sourcing power Sinking power -20 V -1 A Note 1 Note 1. When sinking power, Agilent Model N6784A can operate at the maximum rated output power for only a limited amount of time. The unit monitors the temperature of the internal power devices and latches the output off if the output power causes the temperature to exceed its safe limit. A protect clear is required to resume normal operation. The condition is annunciated by the OT status bit. Refer to the downprogrammer derating figure for the values of the safe limit boundaries. Output Impedance Graphs 42 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 6 Agilent N6783A-BAT, N6783A-MFG Application-Specific Power Modules Performance Specifications ............................................................................ 44 Supplemental Characteristics ......................................................................... 45 Output Quadrant Characteristic ...................................................................... 46 Unless otherwise noted, specifications are warranted over the ambient temperature range of 0 to 40°C after a 30-minute warm-up period. Specifications apply at the output terminals, with each module's sense terminals internally connected to its output terminals (local sensing). Refer to the Agilent N6700 or N6705 Service Guide for the setup conditions for all performance specifications. Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 43 Performance Specifications N6783A-BAT N6783A-MFG 0-8V 0-6V – 2 to +3 A – 2; 0 to +3 A DC Ratings: Voltage Current NOTE 1 Power Low current measurement range 24 W 18 W 150 mA 150 mA 8 mV 8 mV 1.5 mV 1.5 mV Output Ripple and Noise (PARD): (from 20 Hz – 20 MHz) CV peak-to-peak CV rms Load Effect (Regulation): (For any output load change, with a maximum load-lead drop of 0.5V/lead. The load lead drop reduces the maximum available voltage at the load.) Voltage 6 mV 6 mV Current 2 mA 2 mA Voltage 2 mV 2 mV Current 1 mA 1 mA Source Effect (Regulation): Programming Accuracy: (@ 23 °C ±5 °C after a 30 minute warm-up. Applies from minimum to maximum programming range at any load.) Voltage 0.1% + 10 mV 0.1% + 10 mV Positive Current 0.1% + 1.8 mA 0.1% + 1.8 mA Negative Current @ –2 A 0.2% + 1.8 mA N/A Measurement Accuracy: (@ 23 °C ±5 °C. Applies when measuring the default value of 1024 data points with a 20.48 μs time interval.) Voltage 0.05% + 5 mV 0.05% + 5 mV Current high range 0.1% + 600 µA 0.1% + 600 µA Current low range 0.1% + 75 µA 0.1% + 75 µA Load Transient Recovery (Time to recover to within settling band for a load change from 0.15 A to 1.5 A and from 1.5 A to 0.15 A at 6 V output) Voltage settling band NOTE 2 ± 75 mV ± 75 mV Time < 45 µs < 45 µs NOTE 2 1 Output current is derated 1% per °C above 40°C. 2 When relay Option 761 is installed, the settling band is ± 90 mV. The time is < 75 µs. 44 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics N6783A-BAT N6783A-MFG Voltage 15 mV to 8.16 V 15 mV to 6.12 V Positive Current 5 mA to 3.06 A 5 mA to 3.06 A Negative Current – 5 mA to – 2 A Fixed at – 2 A 2.5 mV 2.5 mV Positive Current 1 mA 1 mA Negative Current 10 mA N/A Programming Ranges: Programming Resolution: Voltage Measurement Resolution: Voltage 300 µV 300 µV Current high range 100 µA 100 µA 5 µA 5 µA Current low range (≤ 0.150 A) Programming Temperature Coefficient per °C: Voltage 25 ppm + 50 µV 25 ppm + 50 µV Current 25 ppm + 10 µA 25 ppm + 10 µA Measurement Temperature Coefficient per °C: Voltage 25 ppm + 40 µV 25 ppm + 40 µV Current high range 25 ppm + 2.5 µA 25 ppm + 2.5 µA Current low range (≤ 0.150 A) 25 ppm + 1.5 µA 25 ppm + 1.5 µA Maximum Up-Programming and Down-Programming Time with Full Resistive Load (Time from 10% to 90% of total voltage excursion) Voltage Settling from 0V to Full Scale 4.0 ms 4.0 ms Voltage Settling from Full Scale to 0V 4.0 ms 4.0 ms Maximum Up-Programming and Down-Programming Settling Time with Full Resistive Load (Time from start of voltage change until voltage settles within 0.1% of the full-scale voltage of its final value) Voltage Settling from 0V to Full Scale 20 ms 20 ms Voltage Settling from Full Scale to 0V 20 ms 20 ms Accuracy without disconnect relays 0.25% + 75 mV 0.25% + 75 mV Accuracy with disconnect relays 0.25% + 275 mV 0.25% + 275 mV 0 – 10 V 0 – 10 V 60 µs – 5 ms 60 µs – 5 ms Over-voltage Protection: Nominal range Programmable delay time Over-Current Protection: Programmable delay time 0 – 255 ms 0 – 255 ms 5 mA – 3.06 A 5 mA – 3.06 A 4 mA 4 mA Rms 1 mA 1 mA Peak-to-peak 6 mA 6 mA Nominal Range Output Ripple and Noise: (PARD) CC rms: Common Mode Noise: (From 20 Hz – 20 MHz; from either output to chassis) N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 45 Supplemental Characteristics (continued) N6783A-BAT Remote Sense Capability: Series and Parallel Operation: N6783A-MFG Outputs can maintain DC specifications with up to a 0.5-volt drop per load lead. Maximum sense lead resistance is limited to 300mΩ/lead. Identically rated outputs can be operated directly in parallel. N6783A modules cannot be used in series with other N6783A modules or any other N67xx module. Auto-series and auto-parallel operation is not available. Down-programming Capability: (Current down-programming capability is reduced at output voltages below 0.5 V) Continuous power 12 W 12 W Continuous current 2A 2A Output Quadrant Characteristic N6783A-BAT N6783A-MFG Voltage +8 V (BAT) +6 V (MFG) Current -2 A 0 Key Sourcing power Sinking power 46 +3 A Negative current not programmable on N6783A-MFG N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Chapter 7 Agilent N6700 Modular Power System Mainframes Supplemental Characteristics ......................................................................... 48 Outline Diagrams............................................................................................... 50 Supplemental characteristics are not warranted but are descriptions of performance determined either by design or by type testing. All supplemental characteristics are typical unless otherwise noted. NOTE Refer to the following documents for information about using and servicing the Agilent N6700 Modular Power System Mainframes Agilent Model N6705 DC Power Analyzer User’s Guide Go to http://cp.literature.agilent.com/litweb/pdf/N6705-90001.pdf. Agilent Model N6705 DC Power Analyzer Service Guide Go to http://cp.literature.agilent.com/litweb/pdf/N6705-90010.pdf. Agilent Series N6700 Low-Profile Modular Power System User’s Guide Go to http://cp.literature.agilent.com/litweb/pdf/5969-2937.pdf. Agilent Series N6700 Low-Profile Modular Power System Service Guide Go to http://cp.literature.agilent.com/litweb/pdf/5969-2938.pdf. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 47 Supplemental Characteristics N6700B, N6701A, N6702A N6705A, N6705B 400 W (for N6700B mainframes) 600 W (for N6701A mainframes) 1200 W (for N6702A mainframes) 600 W N/A 20 A N/A Digital TTL level compatible Maximum Power Available for Modules: Values represent combined power rating of all modules installed per mainframe. Front Panel Output Terminals: Maximum current rating BNC Trigger Connectors: I/O Maximum voltage N/A 5V N/A 200 mA USB Current Ratings: Front panel USB connector Rear panel USB connector 300 mA N/A Data Storage: Internal flash memory 4 Gbyte 8 Mbyte (Earlier N6705 models have less memory) Protection Response Characteristic: INH input 5 µs from receipt of inhibit to start of shutdown Fault on coupled outputs < 10 µs from receipt of fault to start of shutdown Command Processing Time: ≤ 1 ms from receipt of command to start of output change Digital Port Characteristics: Maximum voltage ratings +16.5 VDC/− 5 VDC between pins (pin 8 is internally connected to chassis ground). Pins 1 and 2 as FLT output Maximum low-level output voltage = 0.5 V @ 4 mA Maximum low-level sink current = 4 mA Typical high-level leakage current = 1 mA @ 16.5 VDC Pins 1 - 7 as digital/trigger outputs (pin 8 = common) Maximum low-level output voltage = 0.5 V @ 4 mA; 1 V @ 50 mA; 1.75 V @ 100 mA Maximum low-level sink current = 100 mA Typical high-level leakage current = 0.8 mA @ 16.5 VDC Pins 1 - 7 as digital/trigger inputs and pin 3 as INH input (pin 8 = common) Maximum low-level input voltage = 0.8 V Minimum high-level input voltage = 2 V Typical low-level current = 2 mA @ 0 V (internal 2.2k pull-up) Typical high-level leakage current = 0.12 mA @ 16.5 VDC Interface Capabilities: GPIB SCPI - 1993, IEEE 488.2 compliant interface LXI Compliance Class C (only applies to units with LXI label on front panel) USB 2.0 Requires Agilent IO Library version M.01.01 or 14.0 and up 10/100 LAN Requires Agilent IO Library version L.01.01 or 14.0 and up Built-in Web server Requires Internet Explorer 7+ or Firefox 2+ 48 N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Supplemental Characteristics (continued) N6700B, N6701A, N6702A N6705A, N6705B Regulatory Compliance: EMC Complies with European EMC Directive for test and measurement products. ● IEC/EN 61326-1 ● CISPR 11, Group 1, class A ● AS/NZS CISPR 11 ● ICES/NMB-001 Complies with Australian standard and carries C-Tick mark. This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. Safety Complies with European Low Voltage Directive and carries the CE-marking. Conforms to UL 61010-1 and CSA C22.2 61010-1. Environmental Conditions Operating environment Indoor use, installation category II (for AC input), pollution degree 2 Temperature range 0°C to 55°C (output current is derated 1% per °C above 40°C ambient temperature) Relative humidity Up to 95% Altitude Up to 2000 meters Storage temperature -30°C to 70°C Acoustic Noise Declaration: This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January 1991. Sound Pressure Lp <70 dB(A), At Operator Position, Normal Operation, According to EN 27779 (Type Test). Schalldruckpegel Lp <70 dB(A), Am Arbeitsplatz, Normaler Betrieb, Nach EN 27779 (Typprüfung). Output Terminal Isolation: Maximum rating No output terminal may be more than ±240 VDC from any other terminal or chassis ground. N6781A Note When using the AUX measurement input terminals on Model N6781A, no output or input terminal may be more than ±60 VDC from any other terminal and chassis ground. AC Input: Input Ratings ~ 100 VAC – 240 VAC; 50/60/400Hz ~ 100 VAC – 240 VAC; 50/60/400Hz Power Consumption 1000 VA (N6700B) 1440 VA (N6701A) 1440 VA (N6702A @ < 180 VAC input) 2200 VA (N6702A @ > 180 VAC input) 1440 VA Power Factor 0.99 @ nominal input and rated power 0.99 @ nominal input and rated power Internal fuse - not customer accessible. Internal fuse - not customer accessible. Fuse N6702A Note AC mains circuits rated at 100-180 VAC cannot supply enough current to power the N6702A mainframe when operated at its full rated power. When connected to a 100-180 VAC mains, internal circuits will limit the power available to modules to 600 W maximum. Net Weight: Mainframe with 4 modules (typical) N6700B 12.73 kg / 28 lbs N6701A 11.82 kg / 26 lbs N6702A 14.09 kg / 31 lbs Single-wide power module (typical) 1.23 kg / 2.71 lbs 16 kg / 35 lbs 1.23 kg / 2.71 lbs Dimensions: Refer to the outline diagrams on the following page. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide 49 Outline Diagrams 272.6 mm 10.733 in. = airflow 16.9 mm 0.663 in. 425.6 mm 16.756 in. 23.5 mm 0.923 in. 17.7 mm 0.697 in. 50 177.0 mm 6.968 in. N6731B-N6784A DC Power Modules N6700B-N6705B Mainframes Specifications Guide Manual Updates The following updates have been made to this manual since its edition date. 03/20/12 The description of the Voltmeter/Ammeter Measurement Accuracy specification has been updated throughout. The description of the Voltage Measurement Noise and Current Measurement Noise characteristic has been updated on pages 39 and 40. The downprogrammer derating information has been updated on page 42. 06/15/12 External datalogging has been added as a feature on pages 6 and 7. Applies to N6705 firmware revision D.01.08 and up, and N6700 firmware revision. D.01.09 and up. The CC mode graphs have been updated on pages 23 and 31. The N6781A Auxiliary Voltage Measurement input characteristics have been updated on pages 38 and 39. The dc output ratings have been edited to match the instrument labels.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : SPD Company : Agilent Technologies Create Date : 2012:06:27 13:13:24-04:00 Modify Date : 2012:07:02 16:29:33-04:00 Source Modified : D:20120627171219 Subject : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2012:07:02 16:29:33-04:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:3c152b67-e6e3-447a-9036-302b115560cc Instance ID : uuid:b2124850-1ae1-497b-8ddb-29b18039bfb7 Format : application/pdf Title : N6700 Series Specifications Guide Description : Creator : SPD Producer : Adobe PDF Library 10.0 Keywords : Page Layout : SinglePage Page Mode : UseOutlines Page Count : 51EXIF Metadata provided by EXIF.tools