CRT4399 001 AVICZ110BT
User Manual: AVICZ110BT
Open the PDF directly: View PDF 
.
Page Count: 337
ORDER NO.
CRT4399
AVIC-Z110BT/XN/UC
FLASH MEMORY MULTIMEDIA AV NAVIGATION RECEIVER
AVIC-Z110BT
/XN/UC
NAVIGATION AV SYSTEM
AVIC-F10BT/XN/AU
This service manual should be used together with the following manual(s):
Model No.
CX-3250
Order No.
CRT4300
Mech. Module
LS1
Remarks
DVD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
Manufactured under licence from Dolby Laboratories. "Dolby" and the double-D symbol
are trademarks of Dolby Laboratories.
"DTS" is registered trademarks of DTS, Inc.
For details, refer to "Important Check Points for Good Servicing".
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2009
K-ZZZ.-001 JULY 2009 Printed in Japan
1
2
3
4
SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
- Safety Precautions for those who Service this Unit.
When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
C
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION
CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
D
E
F
2
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
B
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
C
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
D
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
F
AVIC-Z110BT/XN/UC
5
6
7
8
3
1
2
3
4
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 6
2. SPECIFICATIONS ............................................................................................................................................ 7
2.1 SPECIFICATIONS ..................................................................................................................................... 7
2.2 DISC/CONTENT FORMAT .......................................................................................................................11
2.3 PANEL FACILITIES.................................................................................................................................. 12
2.4 CONNECTION DIAGRAM ....................................................................................................................... 14
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 15
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 15
3.2 PCB LOCATIONS .................................................................................................................................... 16
3.3 JIGS LIST ................................................................................................................................................ 17
3.4 CLEANING............................................................................................................................................... 18
4. BLOCK DIAGRAM.......................................................................................................................................... 20
4.1 OVERALL CONNECTION DIAGRAM...................................................................................................... 20
4.2 BLOCK DIAGRAM ................................................................................................................................... 22
4.3 POWER SUPPLY SYSTEM FIGURE ...................................................................................................... 34
5. DIAGNOSIS.................................................................................................................................................... 51
5.1 OPERATIONAL FLOWCHART ................................................................................................................ 51
5.2 INSPECTION METHOD OF PICKUP UNIT............................................................................................. 52
5.3 DIAGNOSIS FLOWCHART ..................................................................................................................... 55
5.4 ERROR CODE LIST ................................................................................................................................ 82
5.5 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 84
6. SERVICE MODE ............................................................................................................................................ 85
6.1 TEST MODE ............................................................................................................................................ 85
6.2 DVD TEST MODE ................................................................................................................................. 140
7. DISASSEMBLY ............................................................................................................................................ 145
8. EACH SETTING AND ADJUSTMENT ......................................................................................................... 160
8.1 DVD ADJUSTMENT .............................................................................................................................. 160
8.2 AUDIO UNIT ADJUSTMENT ................................................................................................................. 168
9. EXPLODED VIEWS AND PARTS LIST........................................................................................................ 170
9.1 PACKING ............................................................................................................................................... 170
9.2 EXTERIOR(1) ........................................................................................................................................ 172
9.3 EXTERIOR(2) ........................................................................................................................................ 174
9.4 EXTERIOR(3) ........................................................................................................................................ 176
9.5 EXTERIOR(4) ........................................................................................................................................ 178
9.6 DVD MECHANISM MODULE ................................................................................................................ 180
10. SCHEMATIC DIAGRAM............................................................................................................................. 184
10.1 AUDIO UNIT(PS/IF SECTION)(GUIDE PAGE) ................................................................................... 184
10.2 AUDIO UNIT(SYSCOM SECTION)(GUIDE PAGE)............................................................................. 190
10.3 AUDIO UNIT(AV SECTION)(GUIDE PAGE)........................................................................................ 196
10.4 TUNER IF UNIT(GUIDE PAGE)........................................................................................................... 202
10.5 DVD CORE UNIT(GUIDE PAGE) ........................................................................................................ 208
10.6 CONNECT PCB ................................................................................................................................... 214
10.7 CC UNIT(PS PART)(GUIDE PAGE)..................................................................................................... 216
10.8 CC UNIT(CPU PART)(GUIDE PAGE).................................................................................................. 222
10.9 CC UNIT(CPU SURROUNDING PART)(GUIDE PAGE)...................................................................... 228
10.10 CC UNIT(DDR/FLASH_ROM/SRAM PART)(GUIDE PAGE) ............................................................. 234
10.11 CC UNIT(NAND PART) ...................................................................................................................... 240
10.12 CC UNIT(VIDEO DEC./T-CON/LVDS PART)(GUIDE PAGE) ............................................................ 242
10.13 NAVI UNIT(PS PART)(GUIDE PAGE)................................................................................................ 248
10.14 NAVI UNIT(IF 1SEG PART)(GUIDE PAGE)....................................................................................... 254
10.15 NAVI UNIT(AUDIO,SENSOR PART) ................................................................................................. 260
10.16 NAVI UNIT(IF PART INTERNAL)(GUIDE PAGE) .............................................................................. 262
10.17 MONITOR UNIT(GUIDE PAGE) ........................................................................................................ 268
10.18 KEYBOARD UNIT.............................................................................................................................. 274
10.19 PCB UNIT(SERVICE) ........................................................................................................................ 276
10.20 WAVEFORMS .................................................................................................................................... 278
11. PCB CONNECTION DIAGRAM.................................................................................................................. 284
11.1 AUDIO UNIT......................................................................................................................................... 284
11.2 TUNER IF UNIT ................................................................................................................................... 288
11.3 DVD CORE UNIT ................................................................................................................................. 290
11.4 CONNECT PCB ................................................................................................................................... 292
11.5 CC UNIT............................................................................................................................................... 294
11.6 NAVI UNIT............................................................................................................................................ 298
11.7 MONITOR UNIT ................................................................................................................................... 302
11.8 KEYBOARD UNIT ................................................................................................................................ 306
11.9 PCB UNIT(SERVICE) .......................................................................................................................... 308
12. ELECTRICAL PARTS LIST ........................................................................................................................ 310
A
B
C
D
E
F
4
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
3. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during
power-on mode may damage the ICs inside the unit.
4. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY" .
5. After replacing the pickup unit, be sure to skew adjustment.
6. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector
is plugged or unplugged.
7. Notes on the temperature protection
The temperature protection is set considering the use temperature range of moviNAND.
If the temperature reaches the detection temperature shown below, the operation stops (ASENS is disabled).
B
Detection temperature on low temperature side: -25°C, return temperature: -20°C
Detection temperature on high temperature side: 86.5°C, return temperature: 80°C
8. Control of FAN
There is the control of STOP, low rotation and high rotation.
The temperature (CC unit, DVD mechanism) and the sound volume are detected and controlled it.
9. Pay attention to the connection direction of 140-pin connector when you connect the audio unit and the navi
unit with the expansion jig.
10. Pay attention to the wiring of BT cable. (It affects the sensitivity of BT antenna)
11. Board-to-board connector
With this product, the board-to-board connector is used for the connection between boards.
Remove or attach the board with extra care not to damage the connector.
Assemble the product carefully to prevent an foreign object such as dust and dirt from getting mixed in the
connector joint part.
12. Do not remove the heat release sheet as much as possible.
As the heat release sheet is soft and it may be damaged when you remove it. If it is damaged, please replace
the part with new one.
13. Grill unit (CXE1974, CXE2206)
The plates (CNS9899, CNS9949) and right and left guides (CNS9824, CNS9825) cannot be removed.
If you want to replace the parts of the grill unit, replace the whole grill unit.
14. For the wiring of co-axial cable (CDE8990, CDE8991) in the monitor, the performance may vary depending on
the wiring position.
Please refer to "7. DISASSEMBLY".
15. The procedure of turn off the unit
1) Turn off the ACC line.
2) After 40 seconds, turn off the BUP line.
Note:
Navi software required approximately 40 seconds for storing the data after ACC OFF.
For your information, after the BUP current is less than 380 mA, you can turn off BUP line.
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
5
1
2
3
4
EJECT LOCK MODE for DVD mechanism
In order to change the EJECT LOCK/UNLOCK status of the mechanism, please perform following procedure.
< Procedure >
Top Menu -> AV Source -> Source OFF
A
A
B
C
Short push area "A" -> Short push area "B" -> Long push area "C" on above screen.
(In order to change the status, follow the same operation.)
B
The current status can be confirmed by "OFF" character color.
Eject Lock: OFF
(White character)
Eject Lock: ON
(Blue character)
C
1.2 NOTES ON SOLDERING
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
D
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
E
F
6
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
UC model
Backup current ................... 3.0 mA or less
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
7
1
2
1
2
3
4
3
4
A
B
C
D
E
F
8
AVIC-Z110BT/XN/UC
5
6
7
8
AU model
A
Backup current ................... 3.0 mA or less
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
9
1
2
1
2
3
4
3
4
A
B
C
D
E
F
10
AVIC-Z110BT/XN/UC
5
6
7
8
2.2 DISC/CONTENT FORMAT
A
is a trademark of DVD Format/Logo Licensing Corporation.
B
C
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
11
1
2
3
4
3
4
2.3 PANEL FACILITIES
A
B
C
D
E
F
12
AVIC-Z110BT/XN/UC
1
2
5
6
7
8
A
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
13
1
2
3
4
3
4
2.4 CONNECTION DIAGRAM
A
B
C
D
E
F
14
AVIC-Z110BT/XN/UC
1
2
5
6
7
8
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
A
To keep the product quality after servicing, please confirm following check points.
No.
1
Procedures
Item to be confirmed
Confirm whether the customer complain has The customer complain must not be
2 Flap-mecha
been solved.
reappeared.
If the customer complain occurs with the
Display, video, audio and operations must
specific media, use it for the operation
be normal.
check.
Check the operation of the flap mechanism.
The flap mechanism operation must be
smooth without making the noise and
scratches.
3 DVD
Measure playback error rates at the
B
Deterioration of mecha-drive can be
innermost and outermost tracks by using the checked.
test mode with the following disc.
The error rate must be less than the
DVD test disc (GGV1025)
threshold value.
(Refer to the chapter of DIAGNOSIS for the
threshold value.)
4 DVD
5 CD
6 FM/AM tuner
Play back a DVD.
Display, video, audio and operations must
(Menu operation; Title/chapter search)
be normal.
Play back a CD.
Display, audio and operations must be
(Track search)
normal.
Check FM/AM tuner action.
Display, audio and operations must be
(Seek, Preset)
normal.
C
Switch band to check both FM and AM.
7 GPS positioning
Connect GPS antenna to the product, and
Current location must be correct.
check whether the current location is correct. Display and operations must be normal.
8 Gyro action
On "3D Calibration Status", check whether
Gyro-sensing, display and operations must
the gyro sensor works well by moving the
be normal.
front face of the product from left to right and
up and down.
9 Map display
Touch-panel
Check functions of map scale change and
Display and operations must be normal.
D
map scroll.
operation
Remote-control
operation
10
11
Delete data added during the operating
Make sure to delete data added during the
check.
operating check.
Check whether no media (CD etc.) is inside
The media used for the operating check
the product.
must be ejected.
Appearance check
No scratches or dirt on its appearance after
receiving it for service.
E
See the table below for the items to be checked regarding video and audio:
Item to be checked regarding video
Block-noise
Item to be checked regarding audio
Distortion
Horizontal noise
Dot noise
Disturbed image (video jumpiness)
Too dark
Too bright
Mottled color
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
F
AVIC-Z110BT/XN/UC
5
6
7
8
15
1
2
3
4
3.2 PCB LOCATIONS
A
C DVD Core Unit
D Connect PCB
G Monitor Unit
B
F Navi Unit
B Tuner IF Unit
A Audio Unit
H Keyboard Unit
E CC Unit
C
I PCB Unit(SERVICE)
Unit Number
Unit Number
Unit Name
Unit Number
Unit Number
Unit Name
Unit Number
Unit Number
Unit Name
Unit Number
Unit Name
Unit Number
Unit Name
Unit Number
Unit Name
Unit Number
Unit Name
Unit Number
Unit Name
Unit Number
Unit Name
D
E
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
CWN4335(UC)
CWN4336(AU)
Audio Unit
CWN4824(UC)
CWN4339(AU)
Tuner IF Unit
CXX2608(UC)
CXX2607(AU)
Service CC Assy
CWN3985
Navi Unit
CWN3935
Monitor Unit
CWN3988
Keyboard Unit
EXX1060
PCB Unit(Service)
YWX5009
DVD Core Unit
Connect PCB
F
16
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
3.3 JIGS LIST
CC UNIT
A
GGD1636
Note:
Do not use GGD1632 and GGD1633 at the same time.
The picture will be distorted if you use both of them.
NAVI UNIT
GGD1632
MONITOR UNIT
B
NAVI UNIT
GGD1633
AUDIO UNIT
C
GGD1631
AUDIO UNIT
DVD CORE UNIT
D
GGD1222
GGD1609
E
DRIVE UNIT
GGD1188
TUNER IF UNIT
F
AVIC-Z110BT/XN/UC
5
6
7
8
17
1
2
3
4
Jigs List
A
B
Name
Jig No.
Remarks
DISC
GGV1025
Skew adjustment, Check points after servicing,
Inspection method of Pickup Unit
DISC
TCD-782
Inspection method of Pickup Unit
B to B Extension Cable
GGD1632
NAVI UNIT <---> CC UNIT
Extension Cable
GGD1636
NAVI UNIT <---> CC UNIT
FFC Extension Cable
GGD1633
MONITOR UNIT <--->NAVI UNIT
B to B Extension Cable
GGD1631
AUDIO UNIT <---> NAVI UNIT
FFC Extension Cable
GGD1222
AUDIO UNIT <---> DVD CORE UNIT
FFC Extension Cable
GGD1609
AUDIO UNIT <---> TUNER IF UNIT
FFC Extension Cable
GGD1188
TUNER IF UNIT <---> DRIVE UNIT
Grease List
C
D
Name
Jig No.
Remarks
Grease
GEM1024
DVD Mechanism Module
Grease
GEM1038
DVD Mechanism Module
Grease
GEM1045
DVD Mechanism Module
Locking agents
1401M
Skew adjustment (1401M:produced by THREE BOND)
Bond
GEM1033
Skew adjustment
Bond
1530
Skew adjustment (1530:produced by THREE BOND)
Grease
GEM1024
Drive Unit
Grease
GEM1043
Drive Unit
Tape
GYH1024
Antenna Cable
3.4 CLEANING
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
E
Portions to be cleaned
DVD pickup lenses
Cleaning tools
Cleaning liquid : GEM1004
Cleaning paper : GED-008
Portions to be cleaned
Fans
Cleaning tools
Cleaning paper : GED-008
F
18
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
19
1
2
3
4
4. BLOCK DIAGRAM
4.1 OVERALL CONNECTION DIAGRAM
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A
C D
DVD MECHANISM MODULE
(LS1)
CXK6801-
CN1901
1
30
FFC
B
SD C
GND
B.UP
ACC
SPEED
PULSE
1
CN4
E
JA2001
ILM
P.BREAK REVERSE A.ANT
RL-
FR-
RRRR+
C
FR+
FL+
CDP1095
FUSE
POWER SUPPLY
TERMINALS
1
CN2551
A
RL+
CODE ASS'Y
FL-
30
CC UNIT
E 1/6 CC UNIT (PS PART)
E 2/6 CC UNIT (CPU PART)
E 3/6 CC UNIT (CPU SURROUNDING
E 4/6 CC UNIT (DDR/FLASH_ROM/S
E 5/6 CC UNIT (NAND PART)
E 6/6 CC UNIT (VIDEO DEC./T-CON/
AUDIO UNIT
A 1/3 AUDIO UNIT (PS/IF SECTION)
A 2/3 AUDIO UNIT (SYSCOM SECTION)
A 3/3 AUDIO UNIT (AV SECTION)
1
1
CN2861
CN2571
1
PREOUT
TERMINALS
D
CN5603
CODE ASS'Y
BtoB
32
CDP1194
140
140
GPS
Wired Remote Jack
CN2101
1
6
50
E
FFC
1
50
CN511
JA401
RDS-TMC TUNER (AU only)
CXE2176-
F
20
B
TUNER IF UNIT
AVIC-Z110BT/XN/UC
1
2
3
4
CXE2 0
1
JA5202
JA2880
GPS ANTENNA ASS'Y
CN2512
5
6
7
8
A
SD CARD
1
20
CN4601
8
9 10
5
6
1
2
11
7
1. IPBUS+
2. IPBUSG
3. IPLG
4. NC
5. IPBUS6. IPRG
7. IPL+
8. ASENBO
9. IPR+
10. IPR11. IPL-
B
4
3
1
1
T
CN5602
CN4201
JA5302
BTOB
PART)
MONITOR ASS'Y
120
120
PART)
IPBUS IN
CODE ASS'Y
JA4711
/FLASH_ROM/SRAM PART)
1
1
2
2
JA5201
CDE8990
SURROUNDING PART)
C
D PART)
BT MODULE
LCD PANEL
CWX3813-
EO DEC./T-CON/LVDS PART)
CWX38511
FPC
FPC
60
F 1/4
F 2/4 NAVI UNIT (IF 1SEG PART)
F 3/4 NAVI UNIT (AUDIO,SENSOR PART)
F 4/4 NAVI UNIT (IF PART INTERNAL)
CN5603
FAN
JA5251
1
10
40
CN3100
1
CN3360
1
2
CN3362
G
MONITOR UNIT
1
80
CN3302
CN3300
1
4
FPC
1
D
CN3361
16
1
2
1
2
FPC
CN2901
TOUCH PANEL
H
CSX1148-
KEYBOARD UNIT
CDE8991-
CODE ASS'Y
iPod Connerctor
CN5251
CN5001
1
2
17
CODE ASS'Y
MIC ASS'Y
CDP1195
CPM1083
E
CXM1394
CXE2705
4PIN JACK
17PIN PLUG
DRIVE MECHA
UNIT
CN101
1
1
CN491
GPS ANTENNA ASS'Y
FPC
MIC
GPS
1
CDE8990-
CODE ASS'Y
80
CN3301
1
NAVI UNIT (PS PART)
JA5202
1
CN3401
NAVI UNIT
CN5601
F
2
BTOB
FFC
USB-A
JUNCTION SOCKET
CXE1522F
10
10
I
PCB UNIT
(SERVICE)
AVIC-Z110BT/XN/UC
5
6
7
8
21
1
2
3
4
4.2 BLOCK DIAGRAM
A
115
122
13
27
39
33
F
CN5603
C
D
51
53
55
66
67
68
70
72
77
79
80
81
82
83
84
85
86
87
90
93
98
102
104
105
110
113
117
119
121
123
124
125
126
127
129
132
133
135
137
106
19
109
ROT1
ROT0
NAVI_L
iPod_L
IP_L
iPod_V
E
75
107
PKB
PKG
Q2231
EEPROM
IC2302
S-93C56BD0I-I8
CB
DO
DI
SK
1
4
3
2
BSENS
Q2031
Q2032
BUP
BUPV
NKBUP
113
1
144
138
126
139
133
3
123
122
51
121
50
120
70
119
71
73
129
116
33
127
124
72
75
118
112
111
78
53
110
109
80
108
134
107
106
99
104
101
100
PIPRST
IICSDA
IICSCL
KDT0
FCONT_C
KDT1
KDT2
COMDC
OFFOK
BSENREQ
STOIP
CPUWDT
IPTOS
CCRST
IPPW
ASENREQ
ASENBO
CARDSNS
CCTEMPIN
CTOSYS
BLSYNC
FANCONT
FANON
PBSNS
GNDSEL
SYSTOC
LCD_OE
MVIPW
EPRCE
EPRDI
EPRDO/LEDDT
EPRCK/LEDCK
DIMMER
MBLPW
LCDTMPIN
LEDCS
FCONT_N
FCONT_M
BSENS
BLERR1
BLERR2
CN1901
C
F
SPEED SENS
IC2491
NJM2904M
1
Q2491
22
28
MOTPWR
62
6
14
69
5
15
5
TUN_L
IN+
AU84 RE
IC2131
NJM2388F
4
SYSPW
TUNPDI
TUNPDO
TUNPCLK
TUNPCE1
TUNPCE2
TUNSL
VICS_SDA
VICS_SCL
MOT1
MOT0
MOTPWR2
POS_IN
HOMESW
RDS57K
RDSLK
RDT
RCK
VDT
VCK
VST
MUTEVO
S
SYS
D_FMTOS
D_STOFM
FMCLK
FMCE1
FMCE2
6
5
7
9
10
135
43
42
49
38
65
94
40
18
92
17
25
SDA
SCL
AV S
AN
H/OSW
96
97
95
105
iPod_L
IP_L
iPod_V
IICSDA
IICSCL
23
15
45
35
36
LS_L
LS1V
19
L4-1
43
V4-1
VTR2L
VTR2V
IR REMOTE
REMIN
4
3
U2511
2
SWVDD33
OUT
IN+
5
SYSTEM u-CON
IC2303(1/2)
PEG554A8: A
PEG555A8: B
SPEED
RMUTE
MUTEBUP
L5-1
L3-1
V5-1
SDA
SCL
8
L2-1
39
V2-1
Q2762
RST
98
RESET(100msec)
IC2304
BD5229FVE
RESET
LS1STBY
DTOSYS
SYSTOD
IRQPW
77
88
90
82
64
LS1 LPF
IC2889
NJM4580V
3
Q2551
Q2552
IN+
OUT
LS1STBY
DTOSYS
SYSTOD
IRQPW
XRES
1
19
30
MUTE
TELMUTE
68
Q2303
TELMUTEIN
1 LS_L
ILMSNS
BKSNS
ASENS
AU84
52
89
103
SYSREV
LS1V
VD8V
AVIC-Z110BT/XN/UC
1
1
BUP
KMODE
COMPOSIT
VDD5
LS1VDD
VD(Dry)
VD(Dry)
P2176
VD(Reg)
5
NAVI_L
3 →5 LEVEL SHIFT
IC2530(1/2)
TC74VHCT541AFTS1
Q2492
14 LOUT
12
24
29
30
28
RDS57K
RDSLK
RDT
RCK
TUNSL
GMUTEL
B
KMODEOUT
23 AMUTE
RSTIN 16
D_FMTOS
D_STOFM
FMCLK
FMCE1
FMCE2
FMSL
SDA
SCL
MOT1
MOT0
MOTPWR2
POS_IN
H/OSW
MOT8
NAVI
IC2
BA4
PCHNG
STANBY
LS1 →SRX
S →LS1TX
IRQPWR
XRES
GMUT
TUN_L
CN2551
18
19
20
21
22
A
RDS57K
RDT
PIPRST
TCON_SDA
IICSDA
TCON_SCL
IICSCL
KDT0
FCONT_C
KDT1
EJECT
KDT2
COMDC
OFFOK
BSENRQ BSENREQ
STOIP
CPUWDT
IPTOS
RST_SO
CCRST
IPPW
ASENREQ
ASENRQ
ASENBO
CARDSNS
CCTEMPIN
CTOSYS
BLSYNC
FANCONT
FANON
PBSNS
GNDSEL
SYSTOC
LCD_OE
MVIPW
ILMDT
LEDDT
LEDCK
ILMCK
DIMMER
MBLPW
TEMPSEN LCDTMPIN
ILMLD
LEDCS
FCONT_N
FCONT_M
BSENS
BLERR1
BLERR2
FANUP
AVOUT
GPSREV
SPEED_IN
GUIDE
GMUT
HYOKA
57
CTOEX
59
EXTOC
61
73
Q2505
Q2506
MOTVDD33
GMUTE
103
GUIDE
7
B
12
13
14
15
17
18
27
28
37
38
40
41
43
8
9
11
34
I
36
42
CN2101
AU84
ACC84
VDD33
CN2571
(1/2)
CN511
MOTPWR5 39
B
AUDIO UNIT(1/2)
HRHSLK
19
HRLK
20
HRDT
21
HRCK
22
A
2
3
4
VOUT
CT
3
5
6
7
8
A
GUIDE ISOLATOR/LPF
IC2625
BA4558RFVM
3
IN+
OUT
A AVIC-Z110BT/XN/UC
7
B AVIC-F10BT/XN/AU
C TO 2/2
GUIDE MUTE
AU84
Q2641
Q2643
GMUTE
E-VOL/AUDIO SELECTOR
IC2771
PML017A
UN_L
7
Front_L
IN4+_L
NAVI ISOLATOR
IC2611(2/2)
BA4558RFVM
IN+
7
OUT
9
10
MUTEVO
AU84 REG.
IC2131
NJM2388F84
2
PRE/SW_L
FL
39
RL
40
SWL
9
IN-
OUT
14
14
IN4
12
SYSPW5
IN2
4
JA2001
21
OUT4(+)
23
OUT4(-)
5
OUT2(+)
3
OUT2(-)
FL+
FLRL+
RL-
STBY
BREMOTE 25
H-SW/VOS-DET
AMPMUTE 22
MUTE
ANTB
AU84
MUTEVO
SYSPW5 C
ILMSNS
Q2046
TO 2/2
Q2041
PKG
REV
AV SELECTOR
IC2661
AN15887A
LOUT1
L5-1
L3-1
V5-1
SDA
SCL
ILM
12
C
ASENS
SPEED
GPSREV
SYSREV
Q2226
ACC
14
PULSE
10
PKG
9
REV
11
CN2861
28
47
V6-1
32
VOUT2
BREMOTE
16
BCV
13
RVOUT2 15
BCV
REARVOUT
PFL
OUT MUTE
PFL
23
D
Q2841
PRL
VIDEO LEVEL SHIFT
VOUT1
34
Q2731
Q2732
FRONTV OUT
AVOUT
PRL
Q2842
8
L2-1
39
V2-1
SWL
SWL
PREMUTE
LOUT2
5
Q2831
DUAL ZONE
REAR LOUT
30
4
RLOUT2 12
CORD ASSY
19
L4-1
43
V4-1
VTR2L
VTR2V
16
Q2281
ASENS
_L
V
13
ILMSENS
SYSPW5
23
15
45
35
36
AANT
BUP
NKBUP
BUPV
FANUP
4
d_L
L
d_V
SDA
SCL
B
5
7
6
8
IN1_L
17
DATA
16
CLK
15
STB
14
MUTE
VDT
VCK
VST
1
IN2-L
38
SWL
5
AVI_L
Rear_L
PWR AMP
IC2300
PA2030A
GUIDE MIX
IC2641
NJM2747V
PRL
PFL
GMUTEL
VEHICLE I/F
GUIDE
Q2761
VTR2V
VTR2L 9
VTRIN2V 10
RSTIN
RESET(100msec)
IC2304
BD5229FVE
1
VOUT
CT
E
HYOKA 19
CTOEX 18
EXTOC 17
KMODE 2
HARD RESET
Q2302
3
OFF MUTE
BUP
Q2351
HRSTO
OFFMUTE
1
2
3
4
5
MUTE
IC2531(1/2)
TC74VHCT32AFT AMP MUTE
6
9,10
8
Q2276
TELMUTEIN
TELMUTE
1
AMPMUTE
PRE MUTE
BUP
PREMUTE
Q2242
MUTEBUP
F
AVIC-Z110BT/XN/UC
5
6
7
8
23
1
A
A
2
3
4
AUDIO UNIT(2/2)
A AVIC-Z110BT/XN/UC
B AVIC-F10BT/XN/AU
C TO 1/2
IC2513
TC7SET08FUS1
MSN_RST
36
2
Q2515
4
1
SW BUP
IC2512
TPD1018F
6
CN2512
1
SWBUP
5
B
TMC_MSN_ON
A
1
CTOVICS
SYSTEM u-CON
IC2303(2/2)
PEG554A8: A
PEG555A8: B
B
1
NKBUP
CTOVICS
6
2
VICSTOC
7
3
VICSTOC
2
4
5
5
IC2511
TC7WH126FU
RDSSNS
Q2512
3
CN2571
(2/2)
128
uRDSSNS
Q2513
RDSSNS
VICSTOC
63
CTOVICS
65
RDSSNS
89
Q2514
SWVDD33 REG.
Q2061
Q2062
TMC_MSN_ON5
VDD33
C
TMC_MSN_ON
8
131
SWVDD5 REG.
Q2066
Q2067
VDD5
12
3
114
MOTVDD33 REG.
17
ACCPW5
3→5 LEVEL SHIFT
IC2530(2/2)
TC74VHCT541AFTS1
NAVION
SWACPW
SWVDD5
ACCPW5
Q2101
VDD33
ACCPW
SWVDD33
ACCPW5
1
BUP
ACC84 REG.
IC2121
NJM2388F84
2
18
NAVION5
67
4
16
SWACPW5
2
ACC84
F
4
ACCPW5
48
MOTVDD33
ACCPW5
NAVION 111
SWACPW5 101
SWAC33 REG.
Q2071
Q2072
VDD33
D
P2161
DDCLK
MT81V REG.
IC2161
BD9781HFP
1
BUP
VD8V
C
E
ILMV
6
4
60
BUPV
BUP
ANTON
81
12,13
11
HIVOLT 15 REG.
5
IC2181
LT3461AES6
SYSPW5
P2151
VD5CONT
MOT8
P2107
Q2181
Q2182
TO 1/2
3
4
LS1VDD REG.
IC2151
LT3505EDD
2
5
ANT+B REG.
IC2216
TP1018F
1
ANTON5
BUP
P2162
2
7
37
AU84
SWAC33
LS1VDD
BUPV
VDD5
ANTB
HIVOLT 14 REG.
IC2190
S-812C56AUA-C3K
3
2
HIVOLT 12 REG.
IC2182
S-812C56AUA-C3K
3
IC2531(2/2)
TC74VHCT32AFT
HIVOLT14
HIVOLT
VDD5
ILMV
IO3
SWAC33
1
VDD5 REG.
IC2051
BD3931FP
3
1
3
VDD33 REG.
IC2056
S-1200B33-M5
5
1
AU4.3 REG.
IC2621
NJM2125F
6
AU84
NKBUP
2
3,4
AU8
AU8
1
3
2
4
6
8
10
12
14
KEEP_BUP
16
18
20
22
24
26
28
30
74
130
136
138
VDD5
VDD33
AU4.3
JA2880
WREMIN1
WREMIN2
137
136
WREMIN2
WREMIN1
GND
WREMIN1
WREMIN2
F
24
AVIC-Z110BT/XN/UC
1
2
3
4
C
6
VICSTOC
RDSSNS
HRCK
HRDT
HRLK
23
Lch
TUN_L
ANTENNA IN
2
46
HRCK
29
HRDT
30
HRLK
31
A
4
FMSL
FMCE2
FMCE1
FMCLK
D_STOFM
D_FMTOS
5
3
CN2571
(2/2)
VICSTOC
63
CTOVICS
65
RDSSNS
89
TU33
3
TU33 REG.
IC401
NJM2885DL1-33
1
42
ACC84
MOTVDD33
MOT8
A AVIC-Z110BT/XN/UC
B AVIC-F10BT/XN/AU
CN491
DRIVE UNIT CN101
MOT0
5
MOT1
6
POS_IN
7
H/OSW
10
8
1
2
F
33
34
36
37
38
39
VDD33
AUD84
B
CN2101
CTOVICS
CN511
A
_MSN_ON
RDSCK
18
RDSDATA
19
RDSLOCK
20
5
6
8
CK
9
DI
10
DO
14
3
1
FMANT
AMANT
JA401
TUN_L
1
AUD84
VDD33
TU33
SWBUP
FM/AM TUNER UNIT
FMSL
FMCE2
FMCE1
FMCLK
D_STOFM
D_FMTOS
CN2512
8
A
TUNER IF UNIT
VCC
4
ROMVDD
13
VDD3.3
17
B
7
SL
CE2
CE1
5
9
15
16
17
40
AU84
43
MOT0
13
MOT1
14
POS_IN
10
H/OSW
8
MOTVDD3.3
MOT6V
MOTVDD33
C
MOT6.5 REG.
MOT8
Q491
Q492
Q493
MOTPWR2
11
MOTPWR5
12
RSTIN
35
CN5603
NAVION 111
SWACPW5 101
AU8
AU8
1
3
2
4
6
8
10
12
14
KEEP_BUP
16
18
20
22
24
26
28
30
74
130
136
138
D
E
JA2880
WREMIN2
WREMIN1
GND
WIRED
REMOTE
F
AVIC-Z110BT/XN/UC
5
6
7
8
25
1
2
3
C
4
DVD CORE UNIT
A
NRES
VIDEO+AUD
IC1501
MN2DS0018M
70
NRES
S
S
FLASH 16M
IC1401
CWW1825
B
USB_
IC1402
CWW1826
I2
I2
CP
NRES
12
I
RESET
COM
ST
ST
CMD
IR
E
C
SDRAM
IC1480
K4S641632N-LC75
TRC
TRC
TRC
TRC
T
E
S
F+
E+
D CONNECT PCB
D
LS1 MECHA UNIT
LOADING/CARRIAGE
MOTOR
SPINDLE MOTOR
V
U
W
E
CN1201
CN701
BR
GY
M
MOTOR DRIVER
IC1201
BD8231EFV
CRG1
CRG+
2
32
31
CRG/LE18
CRG/LE+
17
CN101
1
2
3
V
1
2 U
W
3
COIL V
10
COIL U
11
COIL W
12
9
8
7
27
26
28
COIL_V
COIL_U
COIL_W
H1
HUP(HU+),HUM(HU-)
HUP(HU+),HUM(HU-)
H2
HVP(HV+),HVM(HV-)
HVP(HV+),HVM(HV-)
H4
H+
10
H4
H+
10
V
U
W
FCO+ 33
34
FCO36
TKO35
TKO+
HWP(HW+),HWM(HW-)
HWP(HW+),HWM(HW-)
H3
HALL BIASHALL BIAS+
HOME
S101
HOME
8cm
S102
8SNS
12cm
S103
DSCSNS
3
13
HALL_BIAS16
HALL_BIAS+
6
16
3
15
14
4
5
1
VC
2
TKIN
3
FCIN
4
SLIN
5
SLOPOUT
6
LDIN
7
SPIN
8
CTL1
9
CTL2
12
FG
SL/LDOSL/LDO+
14
VHALF
TD
FD
CRGDRV
110
126
127
67
MD
CONT1
CONT2
62
66
63
64
71
HB
VCC5
HOME
65
8cm
49
12cm(DSCSNS)
55
AVIC-Z110BT/XN/UC
1
2
LDIN
MD
CONT1
CONT2
FG
FOP
FOM
TOP
TOM
F
26
VHALF
TD
FD
CRGDRV
3
4
HOME
08EJ
12EJ
D
5
6
7
8
A
CN1901
VIDEO+AUDIO
IC1501
MN2DS0018MAUB
70
NRES
SRCK
ADOUT
LRCK
SDODAC
SCKDAC
LTDAC
DACCK
XRESET
LOUT
ANALOG LOUT
149
151
150
57
58
56
148
1
2
3
13
14
15
16
SRCK
ADOUT
LRCK
SDODAC
SCKDAC
LTDAC
DACCK
BCK
DATA
LRCK
MD
MC
ML
SCK
VOUTL
7
50
COMPOSITE
STANDBY
STSCOMN
CMDCOMN
2
4
SCL
SDA
RESET
IFCOUT
D+
DCOMPOSIT
STANBY
SLVSTS
HSTCMD
IRQPWR
AMUTE
ISC_SCL
I2C_SDA
CP_Reset
X1950
VD5
VDD5
I2C_SCL
I2C_SDA
CP_Reset
IECOUT
ROUT
LOUT
COMPOSITE
STANDBY
STSCOMN
CMDCOMN
IRQPWR
EXTRG1
TRCST
TRCDATA3
TRCDATA2
TRCDATA1
TRCDATA0
TRCCLK
EXTRG0
SDATA
SCLOCK
110
126
127
67
62
66
63
64
71
65
49
55
VHALF
TD
FD
CRGDRV
LDIN
MD
CONT1
CONT2
FG
F+H_G+H
E+G_E+F
LPCO2
LPCO1
VIN3RF
VIN4RF
VIN2RF
VIN1RF
VIN7
VIN8
CDMPD
DVDMPD
TEMP
RFINP
VREFH
VIN1
VIN2
VIN4
VIN3
VIN6
VIN5
9
AUDIO 2CH ANALOG OUT
IC1801
PCM1753DBQ
IC1951
TC7SZU04FU
USB_CLOCK
NRES
47
46
61
152
146
144
138
191
54
53
48
75
VCC5
VCC5 REG.
IC1002
S-1133850-U5
3,4
5
AVCC5 REG.
IC1003
S-1200B50-M5
1,3
27
28
29
25
23
22
19
13
12
A
CN2551
B
11
10
8
7
1.
2
VD8
5
17
VD8
3
D+
D-
AVCC5
C
AMUTE
81
80
79
78
77
76
74
73
72
CN1951
112
111
106
104
100
99
98
97
115
116
105
103
122
96
B
A
C
D
FE1
FE2
3
VCC33
3.3V REG.
IC1004
NJM2885DL1-33
1.2V REG.
IC1005
R1232D121B
8
VCC12
5
LX
VOUT
VIN
VDD
CE
2
3
4
1
TRCST
TRCDATA3
TRCDATA2
TRCDATA1
TRCDATA0
TRCCLK
EXTRG0
SDATA
SCLOCK
VDD5
D
9
CN1101
VREF
VCC5
F+H_G+H
E+G_E+F
RF
109
120
119
118
117
114
113
DEBUG
12
13
VCC33
VDD5
1
2
3
4
5
6
7
8
VREF
F+H/G+H
E+G/E+F
LPCO2
Q1102
Q1104
78LD
LPCO1
Q1101
Q1103
65LD
HOME
CDMPD
DVDMPD
08EJ
Vref
VCC
12EJ
FOP
FOM
TOP
TOM
B
A
C
D
FE1
FE2
78MD
65MD
TEMP
RF
2
3
4
5
7
8
10
11
12
13
E
PU (DP10)
14
15
17
18
20
22
F+
25
F24
T+
23
T26
F
AVIC-Z110BT/XN/UC
5
6
7
8
27
1
E
2
3
4
CC UNIT
A
CPU
IC4001(1/2)
SiRFprima
VIDEO DECODER
IC4903
TT4421
CN4601
X_VIP_PXD[0] - X_VIP_PXD[7]
1.
7
SD_DATA[0] - SD_DATA[3]
|
SD CARD
9
IC4602
TC7SH86FUS1
1
2
SD_DET2
11
SD_DET
14
SD_W
12
SD_CL
5
SD_CMD
2
4
VDD
4
SD_DET
SD_W
SD_CL
SD_CMD
U5
V2
V1
U1
X_SD_CD_B_1
X_SD_WP_B_1
X_SD_CLK_1
X_SD_CMD_1
X_VIP_DVALID_FID
X_VIP_VSYNC
X_VIP_HSYNC
X_VIP_PXCLK
X_VIP_PXD[10]
Y18
AC18
AC19
AC17
AB17
12
13
14
19
35
SD3
LVDS
IC4901
TC90192XBG
LDD_R[1] - LDD_R[5]
LDD_G[0] - LDD_G[5]
LDD_B[1] - LDD_B[5]
CN5602
F
CN4201(1/3)
72
X_L_PCLK
X_L_CLK
X_L_FCK
CASHFSNS
1
2
3
4
6
7
8
9
10
11
12
13
14
15
17
47
45
83
48
TMS
TDI
TDO
TCK
I/O_16
TMS
TDI
TDO
TCK
U15
16
18
19
27
99
I/O_15
I/O_17
I/O_18
I/O_22
I/O_80
AC22
Y22
AA22
AC13
AA18
NTRST
P-TDI
P-TMS
P-TCK
P-RTCK
P-TDO
NSRST
TEST4
JTGRST
E20
J23
J22
E21
H20
J20
H21
W7
GPS
IC4711
GRF3I-0336B
JA4711
F4711
5
D
SPI_CEB
SPI_DI
SPI_CLK
SPI_DO/MAG
SIGN_MAG
ACQCLK
GRFRST
RFIN
13
14
15
16
17
18
19
AB4
AA4
AC4
A2
B3
B2
AC16
X_YN
X_XN
X_YP
X_GPIO[14]
X_GPIO[10]
X_GPIO[9]
X_GPIO[15]
X_GPIO[13]
X_AC97_DOUT
X_GPIO[11]
X_AC97_BIT_CLK
X_GPIO[12]
X_AC97_DIN
X_TEST_MODE[4]
X_AC97_SYNC
X_VIP_PXD[11]
X_UTFS_1
X_UTXD_1
X_USCLK_1
X_GPS_MAG
X_GPS_SGN
X_GPS_CLK
X_VIP_PXD[15]
OPEN/SHORT DETECT
IC4713
BA2115FVM
3
+
2
-
1
Q4711
5
+
6 -
7
SCL_1
SDA_1
GPS33
1
GPS33 REG.
IC4213
BU33TA2WNVX
X_FA[24]
X_GPIO[5]
CCD5F
3
A1
Y1
W1
Y2
W2
AB16
5
6
8
10
11
Q4206
Q4209
U3
U2
T1
SDATAOUT
BITCLK
SDATAIN
SYNC
RESETB
39
HPL
31
MONO
23
LINEL
21
MIC1
X_SCL1
X_SDA1
D2
D1
Y19
4
Q4701
4
AC14 XCCSTBY 2
4
CTOS
13
I2C_SDA/SPI_SOMI
12
I2C_SCL/SPI_SIMO
nRESET
2
AB3
X_RESET_B
W10
Mov
BUP3
IC4221
TC7SA34FU
IC4220
TC7SA34FU
IC4212
TC7SH08FUS1
1
2
4
IC4207
TC7SH08FUS1
CC_RST1
1
4
2
X_SAMPLE_CLK
POWER ON RESET
IC4203
S-80944CNNB-G9E
SD3 REG.
SD3
E17
F16
F17
B17
C17
C16
D15
E16
AC97CODEC
IC4654
WM1616LGEFL
A
4
P17
X_YN
X_XN
X_YP
H23
F23
H22
X_FA[25]
X_TXD_2
W23
94_PLL_IN
X_ SDA1
X_SCL1
iPod authentication coprocessor IC
IC4701
341S2162
X_VIP_PXD[9]
Y23
98_DAC_OUT
56_I2C_Data_IN
55_I2C_Clk_IN
49_Reset_IN
X_SPI_CLK_1
X_SPI_EN_1
X_SPI_DIN_1
X_CKO_0
X_VIP_PXD[13]
CP3
E
U16
Q4903
Q4902
D-R[0] - D-R[4]
D-G[0] - D-G[5]
D-B[0] - D-B[4]
145_STV1
141_Vcom2
140_Vcom1
160_CPH
154_STH
153_Load
150_GOE
147_CPV
U4
58_D-RGB_Clk_IN
T4
45_D-RGB_H_IN
R4
46_D-RGB_V_IN
CPLD
IC4621
PE9019A
F
JA5201
JTAG
C
E1
F1
F2
SPEED_IN
CN4621
DVALID_F
VD_F
30
SDA
HD
32
DTCLK
SCL
RSTN
106_C.Video_IN1
B
86
7
AIN1
CCD3F
2
CCD5F
T5
X_SD_VCC_ON_1
JTG_RST
4
LCD15
POWER ON RESET
IC4206
S-80929CNNB-G8Z
2
CCD3F
JTG_RST
4
LCD25
JTG_RST
CP18
RTC33 REG.
F
RTC33
BUP3
28
1
IC4202
BU33TA2WNVX
C
4
3
VDD5F
AVIC-Z110BT/XN/UC
1
2
3
4
CP3
5
6
Q4901
Q4902
8
CN4201(3/3)
IC4401
IC4402
IC4404
IC4405
HY5DU121622DTP-D43
32
X_ SDA1
X_SCL1
X_GPIO[8]
X_CKO_1
X_IDE_CS_B[0]
X_SD_VCC_ON_0
X_SD_CD_B_0
X_IDE_IRQ
X_LDD[16]
X_LDD[17]
X_LDD[18]
X_LDD[19]
X_LDD[20]
X_LDD[22]
X_GPIO[1]
X_GPIO[6]
NAND(4GB)
IC4501
PEM002B8
LVDS SERIALIZER
IC4902
DS90C241QVS
P17
20
OUT+
19
OUT-
D-R[0] - D-R[4]
D-G[0] - D-G[5]
D-B[0] - D-B[4]
SRAM(4Mbit)
LVDSP
116
LVDSN
118
IC4406
CY62147EV30LL45BVA
B5
1
2
3
10
25
46
47
48
E17
F16
F17
B17
C17
C16
D15
E16
A
CPU
IC4001(2/2)
TT4421
DDR SDRAM(512Mbit x 4)
CN4201(2/3)
AVSEL_OUT
7
CE
X_VIP_PXD[12]
DIN20
DIN21
DIN22
TCLK
DIN0
DIN17
DIN18
DIN19
IC4407
TC7PA53FU
4
1
K22
X_FCE_B[1]
6
A
TCON_SDA
24
TCON_SCL
26
PIPRST
20
PNLYB
73
PNLXL
71
PNLYT
69
RESET
B4
IC4403
PEH224A8
CCPORT2
CCPORT1
FUKKA2
PPW
PVSENS
BT_BOOTS
CPUWDT
PKB
REV
PCHNG
KMODE
RDMSDSENS
GMUTE
ASENRQ
Y16
BT_RESET
AA23
W3
Y3
AC3
AC2
AA2
AB15
W15
AC5
AB5
E22
E23
AA14
HYOKA
CTOEX
EXTOC
SYSTOC
CTOBT
BTTOC
CTOVICS
VICSTOC
USB+
USBAD_SDA_0
AD_SCL_0
BSENRQ
19
1
63
9
12
55
80
104
108
74
106
88
100
84
B
57
48
36
38
44
51
53
42
40
4
6
70
68
78
C
F
L
FLASH ROM(8Mbit)
CN5602
U3
U2
T1
X_IDE_DACK_B
X_TXD_1
X_RXD_1
X_RXD_2
X_UTXD_0
X_URXD_0
X_UTXD_2
X_URXD_2
X_USB_DP
X_USB_DN
X_SDA_0
X_SCL_0
X_GPIO[7]
J21
W4
AC23
P5
N5
W16
J2
J1
J3
K2
K1
L1
C2
AB14
VD18 REG.
1
VD18
CCA3_IOON TR
Q4219
Q4220
CCA3_IOON
4
3
IC4211
BU18TA2WNVX
CCD3F
CCA3F
CCIO_ON
94
P4202
CCD25
CCD25_PLLON TR
C
CCD25_PLLON
MoviNAND Temp. Sensor
BUP3
1
4
SN4201
Q4207
Q4218
MOVITEMP
10
SW_1
11
SW_2
14
SW_3
15
SW_4
F
CCD2.5 REG.
IC4204
LTC3412AEFE
CN5602
NAVI_L
56
MONO
60
LINE_L
47
MIC+
64
39
PL
31
O
23
EL
21
1
1
SVIN
9
PVIN_1
16
PVIN_2
7
RUN/SS
CCD5F
D
POWER ON RESET
IC4217
S-80835CLNB-B6U
13
1
2
CCD5F
CCD3_IOON REG.
CTOSYS
46
7
8
CCD3_IOON
212
08FUS1
USB3 TR
OFFOK
Q4212
Q4214
USB3
76
207
08FUS1
NAVIRST
CCD1.2 REG.
IC4205
LTC3412AEFE
82
P4201
CCD12
PLL12 TR
LCD15 REG.
1
LCD15
IC4208
BU15TA2WNVX
Q4216
Q4217
PLL12
4
3
CCD3F
LCD25
IC4209
BU25TA2WNVX
POWER ON RESET
IC4218
S-80844CLNB-B65
CP18 REG.
1
CP18
CP3 TR
CP3
IC4210
BU18TA2WNVX
2
CCD5F
4
3
4
3
10
SW_1
11
SW_2
14
SW_3
15
SW_4
1
SVIN
9
PVIN_1
16
PVIN_2
7
RUN/SS
POWER ON RESET
IC4216
S-80830CLNB-B6P
LCD25 REG.
1
1
2
4
IC4219
BD6522F
CCD5F
2
CCD3F
NAND3
VDD5F
CCA3F
CCD3F
CCD3
CCD5F
PRE_ON
CCD5F
CCD5
CCD5
1
CCD3_IOON
ANTVCC
1
31
VDD5
75
CCA3
79
CCD3
83
85
87
GPSANTVCC
PLL_ON
E
92
95
97
99
101
103
96
102
14
F
Q4210
Q4211
AVIC-Z110BT/XN/UC
5
6
7
8
29
4
JA5202
ANTIN
36
38
40
74
72
12
13
I
15
16
17
18
I
21
56
ILMV
CCA5
PWRVI
PNLYT
PNLXL
PNLYB
LVDSP
LVDSN
3
4
1
2
CTOBT
BTTOC
BT_BOOTS
BT_RESET
BT_L
5
6
+
7
ANTIN
JA4711
GPS
ANTENNA
6
10
IC5451
NJM2115V
CN5601
JA5201
E
CN3301
LCD_OE
11
KDT0
33
KDT1
35
KDT2
42
G
NAVI UNIT
MIC_BT
F
A
3
PWRBL
2
SWAC33
1
LINE_L
B
CN5602
47
LINE_L
CTOBT
51
BTTOC
53
BT_BOOTS
55
BT_RESET
57
69
71
73
116
118
36
38
48
4
6
C
64
E
CN4201
D
13
20
24
26
32
40
42
44
46
60
72
74
76
78
80
82
84
86
88
100
104
108
110
56
E
F
30
MIC+
31
CCA33
79
75
83
85
87
95
97
99
101
103
GPSANTVCC
102
CCDIO3
96
12
9
106
14
92
68
70
CCA25 REG.
PNLYT(Y+/TR)
PNLXL(X-/TL)
PNLYB(Y-/BL)
LVDSP
LVDSN
CTOEX
EXTOC
HYOKA
USB+
USB-
PNLYT
PNLXL
PNLYB
IC5402(4/4)
NJM13403V
12
CCA5
MIC LPF AMP
IC5404
NJM2125F
NAND3 REG.
5
NAND3
IC5105
S-1200B33-M5
1
3
MOVI5
NAND3
CCA3
VDD5
CCD3
8
1
3
+
-
4
IC5402(1/4~3/4)
NJM13403V
CCA25
1
3
+
-
4
MIC_CC
7
OUT
OUT
MIC AMP(TEL)
MIC AMP
(VOICE RECOGNIZE)
MIC LPF AMP
IC5403
NJM2125F
CCD5
HI-SIDE SWITCH
IC5104
BD6538G
IO3
IO3
PVSENS
PVSENS
PPW
KMODE
PLLON
PRE_ON
AD_SCL0
AD_SDA0
MOVITEMP
PIPRST
TCON_SDA
TCON_SCL
AVSELOUT
VICSTOC
CTOVICS
SYSTOC
CTOSYS
MONO
SPEED_IN
PCHNG
OFFOK
BSENRQ
CPUWDT
NAVIRST
ASENRQ
CARDSNS
RDMSDSENS
GMUTE
PKB
REV
FCONT_C
NAVI_L
14
13
CCA25
1
4
CCD5
VOUT
EN
VIN
OC
IC5103
TC7SET08FUS1
5
3
IPOD5V
4
IC5102
TC7SET04FUS1
1
2
PPW
KMODE
4
2
Q5304
PWRVI
PWRVI
Q5104
Q5105
PWRBL
P5102
BUP
P5103
Q5106
Q5107
PWRBL
BUP
CCTEMPIN
AVOUT
VDD5
3
AD3 REG.
IC5503
BH30NB1WHFV
4
ADC
IC5501
ADS7828E
AD3
1
PLLON
CH0
CH1
CH2
SWBUP REG.
GUIDE
BUP
Q5102
Q5103
CCD5
1
2
3
VDD
RES2
CH4
CH5
5
6
6
5
VREF
VOUT
VDD
8
TEMP SENSOR
SN5501
PRE_ON
AD_SCL0
AD_SDA0
2
15
MOVI5
14
SCL
15
SDA
CH6
CH3
7
4
4
VOUT
VDD
SWDB
AVIC-Z110BT/XN/UC
1
14
GYRO SENSOR
GY5501
RDSSNS
PBSNS
GPSREV
12
OUTX
10
OUTY
8
OUTZ
SWDB
MOVI5 REG.
Q5113
I
Q5116
G SENSOR
IC5407
CSX1149
3
4
1
AD3
IN
MIC HP
(100Hz
5
6
12
AU8
FANCONT
P5104
FNV
GNDD
FAN
2
1
BUP
JA5302
IP_L
GNDSEL
iPod_V
iPod_L
CN5001
Q5108
|
Q5112
IPL+
7
ASENB
ASENBO
Q5201
Q5202
8
ASENBO5
IP-BUS DRIVER
IC5202
HA12241FP
1
2
8
STOIP
IPTOS
IPPW
DIN1 BUS+
ROUT BUSSTBY
6
5
IPBUS+
IPBUS-
IP-BUS IN
(LIGHT BULE)
V_RETURN
FAN REG.
FANUP
FANON
Q5252
IPOD5V
USB+
2
USB1
USB 5V
4
VOUT
13
LOUT
7
CN5251
11
33
35
42
43
41
45
46
47
48
49
50
51
52
53
54
57
61
59
USB/iPod Connector
LCD_OE
KDT0
KDT1
KDT2
ROT0
ROT1
HRST
ILMLD
MVIPW
ILMCK
MBLPW
ILMDT
BLERR2
DIMMER
BLERR1
LCDTEMP
FCONT_M
BLSYNC
COMDC_M
SWAC33
17
18
I
21
56
8
A
CN3301
PWRBL
7
B
1
5
CN5603
(2/2)
TEL)
MP
OGNIZE)
JA5251
IN+
MIC HPF
(100Hz)
3
MICIN+
KDT2
MIC
GNDD
CN5603
(1/2)
CTOEX
59
EXTOC
61
HYOKA
57
LCDTEMP
IC5507
NJM2125F
BSENS
KMODE
133
COMDC_M
107
4
+
-
1
3
COMDC
AU8
AU4
BUP
AD3
101
90
51
53
55
19
63
65
113
93
7
73
75
77
79
81
83
85
87
89
103
105
109
67
13
A
SWACPW5
CCTEMPIN
PIPRST
TCON_SDA
TCON_SCL
AVOUT
VICSTOC
CTOVICS
SYSTOC
CTOSYS
GUIDE
SPEED_IN
PCHNG
OFFOK
BSENRQ
CPUWDT
NAVIRST
ASENRQ
CARDSNS
RDSSNS
GMUTE
PBSNS
GPSREV
FCONT_C
NAVI_L
CN2571
BUP
3.3V/5.0V D/D CONVERTER
IC5001
LTC3850IGN
26
CCD5
BUV
SW1
Q5001
CCA5
25
23
6
16
CCD3
TG1
BG1
KBUP
KBUP
KBUP
KBUP
KBUP
KBUP
KBUP
KEEP_BUP
VDD5
ILMV
IO3
SWAC33
VFB1
SW2
72
C
CN2571
(1/4~3/4)
3403V
39
86
80
82
84
106
104
102
33
27
110
117
66
68
70
122
115
120
127
119
123
125
121
137
124
135
126
132
98
D
A
IP_L
ASENBO
STOIP
IPTOS
IPPW
FANUP
FANON
FANCONT
iPod_V
iPod_L
GNDSEL
LCD_OE
KDT0
KDT1
EJCT
ROT0
ROT1
HRST
ILMLD
MVIPW
ILMCK
MBLPW
ILMDT
BLERR2
DIMMER
BLERR1
TEMPSEN
FCONT_M
BLSYNC
ASENBO5
1
3
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
74
130
136
138
E
Q5002
CCA3
17
20
8
FREQ/PLLFLTR
TG2
28
FCONT_N
Q5003
NAVION5
1
RUN1
13
RUN2
129
111
BG2
VFB2
VIN
22
P5001
BUV
F
AVIC-Z110BT/XN/UC
5
6
7
8
31
1
2
G
A
3
4
MONITOR UNIT
LVDS
IC3150
DS90C124QVS
CN3300
TOUCH PANEL
1
3
4
TOP
BOTTOM
PNLYT
PNLYB
L
PNLXL
ROUT12
I
ROUT16
ROUT6
I
ROUT11
CN3301
45
41
43
7
9
ROUT1
I
ROUT5
PNLYT
PNLYB
PNLXL
LVDSP
LVDSN
41
RIN+
42
RIN-
B
PWRVI
27
D/D CONVERTER
IC3001
BD6171KV
TH3350
TEMP. SENSOR
LCDTEMP
32
EN1
OUT1
VS1
C
24
FCONT_M
44
Q3005
OUT5
22 COM_DC
Q3002
1,2,5,6
V8
ROUT22
4
3.4V FET
4
3
10
Q3001
1,2,5,6
V34
13
22
OUT3
47
OUT4
RT
1
8V FET
4
3
7
11
PVCC1 OUT2
6
PVCC2
4
41
VS2
PVCC
23
42
VCC
PVCC3
48
PVCC4
37
PVCC5
34 MVIPW
RCLK
3
ROUT0
1
ROUT17
1
ROUT18
9
ROUT19
6
ROUT20
5
ROUT21
V5
V5
V18
Q3003
Q3004
38
VM12
COMDC
39 KDT2
46 KDT1
48 KDT0
F
IC3300
BH2227AFV
CN5601
ILMDT
31
ILMCK
33
ILMLD
35
D
20
29
28
30
32
12
11
10
DI
CLK
CSB
AO1
AO2
AO3
1
2
5
RED
GREEN
BLUE
BLSYNC
DIMMER
BLERR1
BLERR2
MBLPW
MBLPW
PWRBL
Q3102
Q3103
IC3101
TC7SH08F
CN3360
77
80
MIC_BT
BTTOC
MIC1P
U0_OUT
BT_BOOTS
Q3360
E
78
79
BOOTS
IC3362
TC7SH08FUS1
1,2
CTOBT
4
U0_IN
BT_RESET
NRESET
75
25
60
|
63
64
65
66
|
68
69
F
32
11
SWAC33
PWRBL
AOUTL
RSTN
MCLK
BICK
SDTI
LRCK
5
1
2
3
4
PWRVI
29
10
I2S_MCLK
37
I2S_CLK
35
I2S_OUT1
38
I2S_SYNC
39
VCC
23
24
V34
Q3101
9
DAC
IC3360
AK4388VT
BT_L
1
2
5
30
BT MODULE CN1
71
DIMMER
IC3100
TC7SH08F
Q3100
2
1
BLSYNC
BLERR1
BLERR2
ILMV
CCA5
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
LVDS
IC3150
DS90C124QVS
CN3401
ROUT12
I
ROUT16
R0-4
30
I
34
ROUT6
I
ROUT11
G0-5
36
I
41
ROUT1
I
ROUT5
1
RIN+
2
RIN-
RCLK
1,2
18
34
ROUT0
11
ROUT17
10
ROUT18
9
ROUT19
6
ROUT20
5
ROUT21
4
CPH
STH1
LOAD
OE
CPV
STV1
2
9,11,13
6
5
4
8,10,12
IC3204
TC74VHCT04AFTS1
3
1,3,5
2,4,6
V5
2
3
+
5
6
+
-
V34
COM/LCD POWER
1
IC3202
NJM082BV
V5
4
7
1
2
5
6
IC3201
TC7S66FU
+
-
7
3
2
+
-
V18
VM12
V DRIVE
1
B
LCD MODULE
48
I
58
V0-10
IC3200
NJM2100V
20
STH1 59
LOAD 29
OE
9
CPV
8
STV1
6
GRADATION
VOLTAGE
IC3203
TC7WT240FU
ROUT22
42
I
46
B0-4
IC3151
TC7SZ08FU
VDD2
26
25
24
L/R 28
VDD1
17
16
VGH
13
VGL
4
Vcom
Q3200
|
Q3203
C
2
1
CN3100
LEDBL
LED1
LED2
1
I
3
5
6
BACKLIGHT
CN3362
BT MODULE
H
JA2901
LED BACKLIGHT DRIVER
IC3102
BD8113EFV
CN3302
ILMV1
ILMV
RED
4
EN
OUTL
18 2,4
Q3106
5-8
LEDBL
GREEN
IC3101
TC7SH08FUS1
1
2
4
8
22
CS
14
OVP
PWM
BLUE
Q3305
Q3303
Q3301
ILMR1
ILMG1
ILMB1
ILMV2
12
LED1
13
LED2
3101
D
CN2901
CN3361
3103
KEYBOARD UNIT
LED1
LED2
Q3304
ILMR2
ILMV1
16
ILMR1
15
ILMG1
14
ILMB1
13
ILMV2
1
ILMR2
2
E
IC3100
TC7SH08FUS1
Q3302
ILMG2
ILMG2
3
3100
2
1
4
6
Q3300
SYNC
KDT0
KDT1
KDT2
9
FAIL1
10
FAIL2
ILMB2
KEY0
KEY1
KEY2
ILMB2
4
KEY0
KEY1
KEY2
8
5
12
KEY MATRIX
F
AVIC-Z110BT/XN/UC
5
6
7
8
33
1
2
3
4
4.3 POWER SUPPLY SYSTEM FIGURE
AUDIO UNIT
A
+B
AUDIO UNIT
HOLD BUP
4 700[uF]/16[V]
BUP
0.5 A/1.6 W
91.5 mA/0.96 Wmax
17 mA
VDD5(Reg)
Constant Power
Supply 5 V
BD3931FP
B
BUPV
3 -> 5 LEVEL SHIFT
TC74VHCT541AFST
MUTE LOGIC(OR)
TC74VHCT32AFT
2 mA
2 mA
SWBUP CONTROL Logic IC
for RDS-TMC/MSN-DIRECT Tuner
TC7SH08FUS1
SWVDD5
2SA1577
10 mA
C
(150 mA/0.3 W)
VDD33(Reg)
Constant Power
Supply 3.3 V
S-1200B33-M5
61 mA
SWVDD5
SPEED I/F
NJM2904M
ACCPW5
10 mA
54.5 mA -> 53 mA uVDD33
VDD33 LC-Filter
49 mA
UVDD33
System u-com
R5F64165PFD
MAX 45 mA
TYP 32 mA
8 mA
D
RESET IC
BD5229FVE
2 mA
SWVDD
2SA1577 5.5 mA -> 4 mA
SWVDD33
ACCPW5
TO NAVI UNIT
IR REMOTE(UW5/AU)
RS-750
SWAC33
2SA1577
SWACC33
2 mA
SWACPW5 EEPROM
E
DualZone
MUTE
RDS DETECT
(EU5/UC/AU)
2SA1576
MOTVDD
UMF21N
ACCPW
F
A
34
C
B
D
AVIC-Z110BT/XN/UC
1
2
3
4
TE
2S
5
6
7
8
A
Power Supply
This block diffiers with
the region of destination.
B
C
RESET Circuit
UMD3N
RESET IC
BD5229FVE
RDS Circuit(EU5/UW5/UC)
UMH1N*2
2 mA
D
TE(UW5/AU)
2 mA
OM
E
TELMUTECircuit
2SA1576A
F
AVIC-Z110BT/XN/UC
5
6
7
8
35
1
2
A
3
4
C
B
D
A
TUNER UNIT
577 mA/3.76 W
ACC84(Reg) ACC84
8.4 V
NJM2388F84
FLAP DRIVE UNIT
3*1SR-154
ACCPW5
max 8 mA
8.88 V-9.24
B
TU33
TU3
NJM2885
typ 172 mA
max 200 mA
typ 103 mA
max 140 mA
300 mA/1.2 W
229 mA
ACC84
AU8.4
max 8 mA
typ 240 mA
max 300 m
typ 105 mA
max 140 m
AV SELECTOR
AN15887A
VIDEO LEVE
2SC4081(RS
C
HIVOLT12
12.4 V
S-812C56AUA
HIVOLT15(D/D)
15.4 V
LT3461A
SYSPW5
HIVOLT
HIVOLT14
13.8 V
S-812C56AUA
D
HIVOLT14
(Center Voltage for Hivolt)
To Guide Mix
HZU6R8
typ 3 mA
max 5 mA
For Audio
436.3 mA/3.141 W over
5 mA
E
AU84(Reg)
8.4 V
NJM2388F84
AU8.4
290 mA
AV4.3(4.2 V)
NJM2125F
(Center Voltage for Audio)
SYSPW5
101.3 mA
(AU8)
For Auto
ANT+B(SW)
TPD1018F
300 mA(MAX)
TO NAVI UNIT
ANTON5
F
F
E
36
G
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
max 8 mA
typ 240 mA
max 300 mA
typ 105 mA
max 140 mA
AV SELECTOR
AN15887A
FM/AM Tuner
B
Second Improved
X-2026
typ:50 mA
max:200 mA
VIDEO LEVEL SHIFT(2 -> 1)
2SC4081(RS)*2
15 mA
C
typ:9.6 mA CAPTAIN7
max:13 mA
typ:56 mA
max:71 mA
9 mA GUIDE MIX
NJM2747V
D
LS1 LPF
NJM2904
5.7 mA
MUTE Circuit
Guide, P-Amp.
UMD3N *3
E
1.6 mA max NAVI ISOLATOR
BA4558RFVM
F
AVIC-Z110BT/XN/UC
5
6
7
8
37
1
2
F
E
3
4
G
A
POWER AMP
TOSHIBA made
IC "PA2030A"
For DVD
SOC 1 A
CEK1254-A
LS1VDD(D/D)
5V
LT3505
MAX 520(TBD) mA
TYP 191(TBD) mA
SOC 0.5 A
CEK1278-
VD5CONT
B
SOC 3.15 A
CEK1259-A
MT81V(D/D)
8.1 V
BD9781HFP
LS1
MAX 1 640(TBD) mA
TYP 450(TBD) mA
DDCLK
60 mA
LITTEL0.25 A
CEK1276-A
C
TO NAV
for ILM
sup
TO TUNER UNIT
SOC1.5 A
CEK1262-
MOTOR 7.5 V/6.5 V
2SB1260(Q)
SA1797(Q)
D
TO FLAP DRIV
MOTOR DRIVER
MOTOR 0/1
MOTPWR5, MOTPW
75 mA/250 mW
SWBUP(EU5/UC/AU)
TPD1018F
RDSSNS MSN_RST:UC
TMC-MSN-ON5:EU5/AU
E
NKBUP
HOLD BUP
10 000[uF]/16[V]
IO33 PKB SNS
TR
FROM NAVI UNIT
TO NAVI UNIT
F
38
AVIC-Z110BT/XN/UC
1
2
3
4
M
5
6
7
8
A
LS1
B
TO NAVI UNIT
for ILM power
supply
C
TO FLAP DRIVER UNIT
RIVER
0/1
Max:200 mA
(Lock 600 mA)
M
Rush
MAX 1 030 mA
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
39
1
A
2
3
4
NAVI UNIT
NAVI UNIT
POWER SUPPLY
(D/D)
FROM AUDIO UNIT
VDD5
BUP
BUPNV
POWER SUPPLY
(Reg)
MAX:14 mA
AU8
ILMV
POWER SUPPLY
SW
GND SELECT
IMD2A
IMH23
MAX:1 mA
AU8
B
GPSANTVCC
S-1200B33
TO
CC UNIT
NAVION5
NO MOUNT
C
MAX:8.5 mA
VDD5
D
IP-BUS Driver
HA12241FP
IPBUSP
IPBUSM
IP-BUS
IP-BUS POWER SUPPLY
SW
2SA1576A
DTC114EUA
BUP
ASENB0
ASENB05
SOC
1A
CEK1254
MAX:360 mA
ILMV
FAN POWER SUPPLY
2SD1760F5(R)
2SA1587(GRBL)
E
SOC
1A
CEK1254
MAX:100 mA
FAN
CXN1394-A
FANUP,FANCONT,FANON
PWR VI SW
2SD1760F5
UMF23N
TO
MONITOR UNIT
MAX:232 mA
SWACPW5
SOC
1.25 A
CEK1255
PWR BL SW
2SB1184F5
DTC143EUA
MAX:480 mA
SWACPW5
F
A
40
B
C
D
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
41
1
A
2
B
C
3
4
D
A
Bup
SWBUP
2SA1576A
2SC4081
TO
MONITOR UNIT
MAX:several uA
PLL_ON
SOC
3.15 A:CEK1259
D/D
NAVI 3 V/5 V
LTC3850IGN
MAX:15 mA
CCA5
5V
3.3 V
MAX:5[mA]
NAVION5
FCONT H:635 kHz
FCONT L:780 kHz
B
BT_AUDIO
NJM2115V
CCA25
MAX:5[mA] MIC HPF
NJM13403V
CCA25
MAX:1.75[mA]
MIC LPF(voice-recongnize)
NJM2125F
CCA25
MAX:1.75[mA] MIC LPF(TEL)
NJM2125F
39 k
NJM13403V
CCA25
C
39 k
2.9 V
BH29NB1WHFV-TR
GND
DTV3
MAX:42.1 mA
DTV5
1.8 V
BU18TA2WNVX
DTV5
1.2 V
BH12PB1WHFV
DTV3
MAX:900 mA
CCD3
D
ANT
CKS5701A
8V
R1515H080B
MAX:25 mA NOT
Logic IC
TC7SH04FUS1
E
NM
CCDIO3
DTV3 MAX:12[mA]
EMI
FIL
NM
IO3
MAX:24 mA R232C Driver
UPD4721GSS1
ET
N
F
F G
E
42
H
I
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
B
econgnize)
C
2.9 V
BH29NB1WHFV-TR
1.8 V
BU18TA2WNVX
VDDS
MAX:2.6 mA
VDDRF
MAX:47 mA
VDDL
MAX:0.4 mA
VDDC
MAX:13.2 mA
VCCA
MAX:25 mA
VCCB
MAX:25 mA
1.2 V
BH12PB1WHFV
ANT
CKS5701A
VCCA MAX:3 mA
1-Seg FE
CWX3768
3.3 V <-> 1.8 V
TC7WPB9306FK
D
3.3 V <-> 1.8 V
TC7MP3245FTG
T
c IC
SH04FUS1
E
VCCB MAX:12 mA
NOT MOUNT
ETC
NOT MOUNT
F
AVIC-Z110BT/XN/UC
5
6
7
8
43
1
2
3
F G
E
H
4
I
A
MAX:1 500 mA
NOT/AND Logic IC
CCD5
MAX:50 mA TC7SET04FUS1
TC7SET08FUS1
USB Highside switch
BD6538G
USB/iPod5
BSENS,PPOWER
MAX:1.75[mA] COMDC LPF
NJM2125F
SW
2SA1577A
DTC114EUA
COMDC
PREON
B
SW
2SA1576A
DTC114EUA
0 ohm
3.3 V
S-1200B
PREON
VDD5
MAX:5.4 mA
C
LED SIGNAL
CONNECTION
HN1B04FU(Y)
SECRITY CONNECTION
AND Logic
TC7SET08FUS1
SECCONT,ASENS
NOT MOUNT
3.0 ± 0.1 V
VDD5
3V
BH30NB1WHFV-TR
AD3
GYRO Sensor
CSX1147
3.0 V ±
TYP:1.
PLL_ON
G Sensor
CSX1149
D
ADC
ADS7828E
3.0 V(2
TYP:0.
MAX:0
Temp Sensor
S-58LM20A-N4
3.0 V(2
TYP:0.
MAX:0
E
F
44
AVIC-Z110BT/XN/UC
1
2
3
3.0 V(2
TYP:0.
MAX:0
4
5
6
7
8
A
ch
USB/iPod5
USB, iPod
T
O
C
C
0 ohm
NAND3 MAX:80[mA]
3.3 V
S-1200B33
CCD3
B
U
N
I
T
CCD5 MAX:1 160[mA]
CCA3
MAX:54mA
VDD5 MAX:26[mA]
C
sor
3.0 V ± 0.15 V
TYP:1.7 mA
3.0 V(2.4 V-3.6 V)
TYP:0.68 mA
MAX:0.85 mA
3.0 V(2.7 V-3.6 V)
TYP:0.225 mA
MAX:0.32 mA
or
-N4
D
3.0 V(2.7 V-5.5 V)
TYP:0.004 5 mA
MAX:0.006 mA
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
45
1
CC UNIT
A
2
3
4
TO NAVI UNIT
VDD5
Power supply
(D/D)
Power supply
(LDO)
LDO
RTC3.3V
BU33TA2WNVX RTC3
B
TYP:21 mA
1.2 ± 0.12 V
CCD5
D/D
CCD1.2V
LTC3412A
CCD12
PRE_ON
MAX:248.6 mA MAX:880.5 mA
(Efficiency:85%)
C
BD6522F
CCD3
1.25 V:0.1 mA
CCD33
PLL_ON
IO_ON
MAX:516.1 + @ mA
PLL_ON
MAX:911.2 + @ mA
2.5 ± 0.2 V
CCD25
D/D
CCD2.5V
LTC3412A
IO_ON
D
NAND3
V
MAX:1 549.1 + @ mA
2.5 ± 1%
LDO
LCD25
BU25TA2WNVX
Sequence generation
MAX:105 mA
Pc:84 mW
LCD25
E
RST1
3.0 V
B
A
F
46
1.5 ± 0.025 V
LDO
LCD15
BU15TA2WNVX
PRE_ON
RST2
3.5 V
IO_ON
RST3
4.4 V
PLL_ON
D
C
AVIC-Z110BT/XN/UC
1
2
3
4
MAX:120 mA
Pc:216 mW
LCD15
5
6
7
8
A
Power supply
(LDO)
Power supply
(Reg)
CC UNIT
CPU
SiRF_Prima
RTC
VDD_RTC 0.96 V-1.26 V TYP:1 mA
VDD_LVR 2.3 V-3.6 V TYP:1 mA
VDDIO_RTC 3.3 V(2.3 V-3.6 V) TYP:1 mA
3.3 V
PLL12
1.2 V
1.2 V
CORE
1.2 V
PLL
B
VDD_PRE 1.2 V ± 0.06 V TYP:50 mA
VDD_PDN 1.2 V ± 0.06 V TYP:800 mA
VDDA_PLL 1.2 V ± 0.06 V TYP:10 mA
VDD_PLL 1.2 V ± 0.06 V TYP:10 mA
VDDIO_PLL 3.3 V 3.0 V-3.6 V TYP:100 mA
PLL_ON 3.3 V
mA
PLL_ON
2.5 V
1.25 V
MEM
1.2 V
2.5 V
TSC
USB3
3.3 V
CCD25V
2.5 V
PLL_ON
VDDIO_MEM 2.4 V-2.6 V-2.7 V TYP:100 mA
VREF_MEM 0.49-0.51*(VDDIOMEM) TYP:0.005 mA
VDD_TSC 1.14 V-1.26 V TYP:0.5 mA
VDDA_TSC 2.25 V-2.75 V
TYP:25 mA
VDDIO_TSC 2.25 V-2.75 V
VREF_ADC 2.5 V 2.0 V to 2.75 V TYP:@ mA
VDDA3V3_USB 3.0 V-3.6 V TYP:6 mA
VDDA2V5_USB 2.5 V ± 0.25 V TYP:22 mA
USB
eFUSE
3.3 V
VREF125
1.25 V
2.5 V
VPROG 2.5 V ± 0.25 V TYP:30 mA
IO
VDDIO 3.0 V-3.6 V TYP:100 mA
DDR SDRAM
HY5DU121622DTP-J-K
512Mb x 4
3.3 V(IO)
movi-NAND
3.3 V(CORE) PEM002B8
MAX:105 mA
Pc:84 mW
LCD25
2.6 V ± 0.1 V
MAX:350 mA *4
1.25 V ± 0.125 V
MAX:1 mA? *4
D
3.3 V(2.5 V-3.6 V)
MAX:100 mA
3.3 V
NOR-Flash
S29GL512P11TFI010
2.5 V
T-CON
TC90192XBG
1.5 V
3.3 V
C
3.3 V ± 0.3 V
MAX:90 mA
3.3 V ± 0.3 V
MAX:70 mA
1.5 V ± 0.2 V
MAX:120 mA
2.5 V ± 0.2 V
MAX:105 mA
E
MAX:120 mA
Pc:216 mW
LCD15
3.3 V
SRAM(1M)
CY62126EV30LL55BVE
3.3 V(2.2 V-3.6 V)
MAX:20 mA
3.3 V
iPod
certification
IC
3.3 V(1.8 V-3.6 V)
MAX:10.0 mA
BUP3
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
47
1
2
3
B
A
A
4
D
C
CCA3
CCA33
IO_ON
SD3
X_SD_VCC_ON
(for SiRFprima)
1.8 ± 0.025 V
LDO
VD18
BU18TA2WNVX
IO_ON
B
LDO
VA18
BU18TA2WNVX
IO_ON
1.8 ± 0.025 V
LDO
CP18
BU18TA2WNVX
C
3.3 ± 1%
LDO
GPS33
BU33TA2WNVX
CCD
MAX:76 mA
Pc:114 mW
VD18
VA18
TYP:11 mA
Pc:16.5 mW
CP18
MAX:18 mA
Pc:30.6 mW
GPS_SAMPLE_C
D
E
F
48
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
E
CCA33
A
3.3 V(A)
AC97-CODEC
3.3 V(D) WM1616LGEFL
O_ON
SD3
3.3 V
SD Card
power supply
3.3 V(2.7 V-3.6 V)
MAX:80 mA
1.8 V
3.3 V
1.8 V
VIDEO-Decoder
AK8853
3.3 V ± 0.3 V
TYP:4 mA
MAX:** mA
1.8 V(1.7 V-2.0 V)
TYP:54 mA
MAX:76 mA
1.8 V
3.3 V
CPLD
PE9019A
3.3 V ± 0.3 V
MAX:6 mA
1.8 V ± 0.1 V
TYP:11 mA
MAX:** mA
X_SD_VCC_ON
MAX:76 mA
Pc:114 mW
VD18
3.3 V(2.7 V-3.6 V)
MAX:32.1 mA
B
VA18
TYP:11 mA
Pc:16.5 mW
CP18
C
CP18
3.3 V
MAX:18 mA
Pc:30.6 mW
GPS33
3.3 V
LVDS TX
DS90C241
3.3 V ± 0.3 V
TYP:45 mA
MAX:70 mA
GPS-RF
GRF3i+
3.3 V
(2.6 V-2.85 V-3.6 V)
TYP:16.0 mA(2.85 V)
MAX:18.0 mA(2.85 V)
GPS Antenna
power supply
3.3 V
TYP:19 mA
MAX:30 mA
PS_SAMPLE_CLK
D
USB jig
ETHER jig
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
49
1
2
3
4
MONITOR UNIT
A
Power supply
Electric current unit: mA
KEY PCB
NAVI side
ILM8
typ -
SWACC3
SWACC3
typ
max 0
typ 0.7
max 1
PU,PD…etc
typ 1.6
max 3.2
typ 0.8
max 2
RGB Illumination
DAC
BH2227AFV
typ 0.1
max 0.2
DD Converter
BD6171KV Actual survey value:26.555
typ 32.4
5V
max 52.1
B
min 150.29
typ 157.36
max 203.14
PWVI
260.5
18.5 V
Actual survey value:0.194
typ 0.21
max 0.315
LED
LED
TEMP SENSE
CCX1063-A
Actual survey value:0.326 VCOM AMP
NJM2100 (max5.)
typ 3.5 TC7S66FU
max 5
5.8275
min 297.56
typ 311.69
max 420.25
PWBL
-12 V
123.96
1284.855
3.3 V
Actual survey value:10.877
typ 8.42
max 10.33
Actual survey value:106.70
typ 287.9
max 389.35
Actual survey value:7.531
typ 7.5 Gradation part
TC7WT240FU
max 15 TC74VHC04FTS1
Actual survey value:18.698 LCD Panel
typ 21.4
max 32.1
80
C
8V
Actual survey value:10.709
typ 8.4
max 10
Actual survey value:0.194
typ 0.21
max 0.315
Actual survey value:0.193
typ 0.22
max 0.33
Actual survey value:3.70
typ 2.9
max 4.35
D
Actual survey value:10.684 VCOM
typ 8.2 NJM082(max5.6)
max 10
+
Actual survey value:10.709
typ 8.4 Tr Buffer
max 10
Actual survey value:42.8 LVDS::DS90C124
typ max 85 min:3.0 V
typ:3.3 V
max:3.6 V
E
Actual survey value:60.2
typ 200 BT
max 300 CK5050+
DD Converter
(14 V -> 27 V)
BD8113FM
CCA5
Actual survey value:12.94
typ 18
max 27
LED Backlight
Actual survey value:
typ 120
max 130 CWX3913-A
Actual survey value:12.94
typ 18 DAC to BT
max 27 AK4388VT
F
50
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
OFFOK : Pin 123
CCRST : Pin 120
IO_ON : Pin 115
NO
NO
NO
MBLPW -> H
BLSYNC -> PULSE
DIMMER -> PULSE
MBLPW : Pin 108
BLSYNC : Pin 33
DIMMER : Pin 80
IO_ON -> H
CCRST -> H
OFFOK <- H
The backlight lights.
PIPRST -> H
PIPRST : Pin 113
PRE_ON -> H
LS1STBY : Pin 77
XRES : Pin 64
DDCLK : Pin 37
VD5CONT : Pin 60
The communication with
LS1 begins.
LS1STBY <- H
XRES -> H
DDCLK -> PULSE
VD5CON -> H
7
The communication with
CC begins.
MVIPW -> H
MVIPW : Pin 111
Standby
NAVION -> H
Parallel Operation
SWACPW -> H
ACCPW -> H
YES
ASENS = L?
YES
BSENS = L?
YES
VCC = 3.3 V?
6
PRE_ON : Pin 125
NAVION : Pin 48
SWACPW : Pin 67
ACCPW : Pin 114
ASENS : Pin 103
BSENS : Pin 104
74, 91, 132
VCC : Pin 23, 39, 59,
RESET
5
8
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
B
AVIC-Z110BT/XN/UC
8
C
D
E
F
51
1
2
3
4
5.2 INSPECTION METHOD OF PICKUP UNIT
Disc to be used
A
CD-DA: TCD-782
DVD-Video: TDV-582
Execution method
Replace the PICK UP
START
LD turned on?
B
SKEW ADJ.
Check parts
No
Yes
Check point:
AS MAX check
Check point:
LD current check
LD current check
Is it OK?
RF level check
Is it OK?
Replace the PICK UP
No
No
Check point:
Error rate check
Yes
Yes
Error rate check
C
Is it OK?
No
Check point:
AS MAX check
RF level check
Is it OK?
No
Yes
PICK UP
cleaned?
Yes
No
Perform lens
cleaning
Yes
D
Replace the PICK UP
Check point:
Error rate check
Error rate check
Is it OK?
No
Yes
PICK UP
cleaned?
No
Perform lens
cleaning
Yes
Replace the PICK UP
E
Ckeck parts
other than PICK UP
Finished
F
52
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
LD current check
Check
Status: [Foucs closed] of TEST MODE
NO.
Disc
1
GGV1025
A
Check Point
Threshold
DVDLD1-VCC5_3
Remarks: LD current
60 - 390 (mV)
10 - 65 (mA)
Expansion
B
C
NO. Disc
2
TCD-782
Check Point
Remarks: LD current
Threshold
CDLD1-VCC5_3
60 - 360 (mV)
10 - 60 (mA)
Expansion
D
Notes: Please pay attention to the laser diode damage by static electricity.
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
53
1
2
3
4
ASMAX check
ASMAX value shows the value of RF level.
Status: [Foucs closed] of TEST MODE
A
No.
Disc
Check Point
8 digits value of
ASMAX
GGV1025
on display
8 digits value of
TCD-782
ASMAX
on display
1
2
Threshold
more than
0000 0B00
more than
0000 0C00
Remarks:
Only four last digits are
displayed according to
the product.
Only four last digits is
displayed according to
the product.
Test mode display will not appear on the display of this product. Connect the rear monitor output to a monitor.
B
In this case, the value is displayed for a split second.
When you tried to perform [FOCS CLOSE],
the display will charge automatically in the following order.
[1FFF0000]->[FEMAX]->[FE MIN]->[AS MAX]->
[ENV MAX]->[FE normal]->[Spindle gain]->
[TEMAX]->[TEMIN] ->[20000000]
Watch carefully the value of ASMAX.
C
Error rate check
Status: [Tracking Closed] of TEST MODE
No.
1
2
D
3
Disc
Check Point
Threshold
less than
GGV1025
ID: 40000
1.000E-03
less than
GGV1025
ID: 200000
1.000E-03
less than
TCD-782 ID: HOME Position
2.500E-03
Remarks:
Test mode display will not appear on the display of this product. Connect the rear monitor output to a monitor.
E
F
54
AVIC-Z110BT/XN/UC
1
2
3
4
5
NO
NO
Go to FE
section check.
YES
Is the life of flash
memory OK?
Conduct check item 12.
YES
Does the
operation
take time?
6
7
AVIC-Z110BT/XN/UC
8
YES
END
NO
Product repair
Replace the unit.
YES
The product
is normal?(iPod
attestation IC)
Go to FE related
repair process.
NO
Go to the
product check.
YES
Is the iPod
circuit OK?
Execute check 14.
YES
Is the iPod play
in error?
NO
NO
NO
Replace the unit.
YES
Is the USB
circuit OK?
Execute check 14.
YES
Is 48 MHz OK?
Execute check 13.
YES
Is the USB play
in error?
NO
NO
NO
NO
END
YES
Normal?
Repair the
defective part.
Go to FE
section check.
YES
Is the audio
circuit OK?
Execute check 10.
YES
Is DACCLK
normal?
Execute check 9.
YES
Is AVCC5
voltage OK?
Execute check 8.
YES
Is the sound
in error?
NO
NO
NO
Go to FE
section check.
YES
Is VD8, VCC5
power supply
voltage OK?
Execute check 7.
YES
Is SDRAM
IF OK?
Execute check 6.
YES
Standby
OK?
Execute
check 1.
NO
NO
NO
Replace the unit.
YES
Is 27 MHz
OK?
Execute check 5.
YES
Is VSENS
OK?
Execute check 4.
YES
Reset OK?
Execute check 3.
YES
Is VDD5(VCC33, VCC12)
power supply voltage OK?
Execute check 2.
7
Normal?
YES
Replace the unit.
YES
Is FE section
normal?
YES
NO
NO
YES
Can the
playback
start?
START
6
NO
YES
Is AVCC5
voltage OK?
Execute check 8.
YES
Is the image
in error?
Is the video
circuit OK?
Execute check 11.
Go to FE
section check.
NO
NO
NO
BACK END section flow
5
8
5.3 DIAGNOSIS FLOWCHART
A
B
C
D
E
F
55
1
2
3
4
Check 1: Standby OK?
A
Check the voltage at the “STANBY” test point while the power is on.
Use the “DGND1” test point at the reference.
NO.
Check point
1 STANBY-DGND1
Module No.
ALL
Specification value
VCC33 V0.6 V or more
Unit
V
Side A
B
C
STANBY
Fig 1.1: STANBY check point
D
E
F
56
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 2: Is VDD5 (VCC33, VCC12) power supply voltage OK?
VDD5
IC1004
3.3 V output regulator
IC1005
DC/DC converter
1.2 V output
VCC33 (= 3.3 V)
VCC12 (= 1.2 V)
IC1401 FLASH power supply (Data)
IC1402 FLASH power supply (Program)
IC1481 SDRAM power supply
IC1501 DV5U power supply
A
IC1501 DV5U power supply
Fig 2.1: Power supply configuration
Check the voltage at the “VDD5_1, VCC33_1 and VCC12_1” test point while the power is on.
Use the “DGND1” test point at the reference.
B
NO.
Check point
1 VDD5_1 - DGND1
2 VCC33_1 - DGND1
3 VCC12_1 - DGND1
Specification value
5.0 ± 0.4
3.3 ± 0.15
1.2 ± 0.12
Module No.
ALL
ALL
ALL
Unit
V
V
V
Side A
C
VCC33_1
VCC12_1
D
DGND1
VDD5_1
Fig 2.2: VDD5, VCC33, VCC12 voltage check points
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
57
1
2
3
4
Check 3: Reset OK?
A
Check the voltage at the “XRES” test point while the power is on.
Use the “DGND1” test point at the reference.
NO.
1
Check point
XRES-DGND1
Module No.
ALL
Specification value
VCC33 ×
0.7 or more
Unit
V
Side A
B
C
DGND1
NRES
Fig 3.1: RESET check point
D
E
F
58
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 4: Is VSENS OK?
CN1901
HOST I/F
A
R1004,
R1007
VD8
VDD5
STANBY
XRES
IC1004
Regulator
VCC33
IC1005
DC/DC
converter
VCC12
VSENS
IC1501
DV5U
B
Fig 4.1: Power supply configuration and VSENS
Check the voltage at the “VSENS” test point while the power is on.
Use the “DGND1” test point at the reference.
NO.
Check point
1 VSENS - DGND1
Module No.
ALL
Specification value
0.95 - 1.07
VD8 = 8.0 ± 0.4 V
Unit
V
C
Side A
VSENS
D
DGND1
E
Fig 4.2: VSENS check point
F
AVIC-Z110BT/XN/UC
5
6
7
8
59
1
2
3
4
Check 5: 27 MHz Normal?
Each clock is created inside the IC1501 using the 27 MHz master crystal oscillator (X1501).
A
IC1501
DVD-LSI
OSCO
X1501
27 MHz
crystal
OSCI
B
VCC33
VCC12
Fig 5.1: Clock configuration
Turn the power on, and check with DGND being the reference.
In case of NG, check the applicable line, periphery of IC1501,
soldering of the peripheral components and defective components.
NO.
2
Check point
Module No.
IC1501 169pin
ALL
C
Specification value
27 MHz
± 50 ppm
Unit
ppm
Specification
value
GND
Fig 5.2: Clock specification value
Side A
D
E
IC1501 158pin
DGND1
Fig 5.3: 27 MHz check point
F
60
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 6: Is SDRAM I/F OK?
In order to secure the MPEG stream data as the buffer,
the capacity of communication I/F SDRAM between the LSI and the memory is 64Mbit.
Be careful as XCSM, XWE, XCAS and XRAS of IC1480 are called differently in IC1501,
namely NCSM, NWE, NCAS, NRAS.
IC
IC1501
MA0 - 11
1480
DV5U
MDQ0 - 15
SDRAM
MCK
A
XWE(NWE)
XCAS(NCAS)
XRAS(NRAS)
XCSM(NCSM)
DQM0
DQM1
BA0
BA1
B
Fig 6.1: SDRAM I/F
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
61
1
2
3
4
Check the conductivity at “check point 1” and “check point 2” without power.
In case of NG, check the soldering and defective components throughout the
“output t input” of the applicable section.
A
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
B
C
D
Signal name
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
MA11
MDQ0
MDQ1
MDQ2
MDQ3
MDQ4
MDQ5
MDQ6
MDQ7
MDQ8
MDQ9
MDQ10
MDQ11
MDQ12
MDQ13
MDQ14
MDQ15
MCK
XWE
XCAS
XRAS
XCSM
DQM0
DQM1
BA0
BA1
Check point 1
IC1480
23pin
IC1480
24pin
IC1480
25pin
IC1480
29pin
IC1480
30pin
IC1480
31pin
IC1480
32pin
IC1480
33pin
IC1480
34pin
IC1480
33pin
IC1480
22pin
IC1480
35pin
IC1480
2pin
IC1480
4pin
IC1480
5pin
IC1480
7pin
IC1480
8pin
IC1480
10pin
IC1480
11pin
IC1480
13pin
IC1480
42pin
IC1480
44pin
IC1480
45pin
IC1480
47pin
IC1480
48pin
IC1480
50pin
IC1480
51pin
IC1480
53pin
IC1480
38pin
IC1480
16pin
IC1480
17pin
IC1480
18pin
IC1480
19pin
IC1480
15pin
IC1480
39pin
IC1480
20pin
IC1480
21pin
Check point 2
IC1501
201pin
IC1501
203pin
IC1501
207pin
IC1501
209pin
IC1501
208pin
IC1501
206pin
IC1501
202pin
IC1501
200pin
IC1501
198pin
IC1501
194pin
IC1501
199pin
IC1501
192pin
IC1501
160pin
IC1501
162pin
IC1501
164pin
IC1501
168pin
IC1501
170pin
IC1501
172pin
IC1501
176pin
IC1501
178pin
IC1501
177pin
IC1501
175pin
IC1501
171pin
IC1501
169pin
IC1501
167pin
IC1501
163pin
IC1501
161pin
IC1501
159pin
IC1501
183pin
IC1501
181pin
IC1501
188pin
IC1501
189pin
IC1501
190pin
IC1501
179pin
IC1501
180pin
IC1501
193pin
IC1501
197pin
Specification value
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
0.17 ohm or lower
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
56 ohm ± 5 %
E
F
62
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Side B
A
B
Check point 1 (IC1480)
Side A
C
D
Check point 2 (IC1501)
Fig 6.2: SDRAM I/F check point
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
63
1
2
3
4
Check 7: Is VD8, VCC5 power supply voltage OK?
A
VD8_1
F.E. driver system
VD8_2
IC1002
REG IC
for VCC 5 V.
VCC5 (= 5.0 V)
Power supply
for PU
Fig 7.1: Power supply configuration
Check the voltage at the “VD8_1, VD and VCC5_1” test point while the power is on.
Use the “PGND3 and AGND1” test point at the reference.
B
NO.
1
2
3
Check point
VD8_1 - PGND3
VD - PGND3
VCC5_1- AGND1
Module No.
ALL
ALL
ALL
Specification value
8.0 ± 0.4
8.0 ± 0.4
5.0 ± 0.1
Unit
V
V
V
Side A
AGND3
C
VCC5_1
PGND1
D
VD8_1
VD
PGND3
Fig 7.2: VD8, VCC5 voltage check points
E
F
64
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 8: Is AVCC5 voltage OK?
IC1003
REG IC
for AVCC 5 V.
VD
AVCC5 (= 5.0 V)
A
IC1801
Audio-DAC
Fig 8.1: Power supply configuration
Playback DVD-REF-A1 TITLE 1 and check the voltage at the stylus.
Check with PGND and GNDAU being the reference.
NO.
1
2
Check point
VD - PGND_3
AVCC5 - GNDAU1
Module No.
ALL
ALL
Specification value
8.0 ± 0.4
5.0 ± 0.1
Unit
V
V
B
Side A
C
AVCC5
D
PGND3
VD
GNDAU1
Fig 8.2: VD8, AVCC5 voltage check points
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
65
1
2
3
4
Check 9: Is DACCLK normal?
DACCLK for Audio-DAC is created by IC1501 using the 27 MHz master crystal oscillator (X1501).
A
IC1501
X1501
27 MHz
crystal
DVD-LSI
IC1801
Audio-DAC
DACCLK
VCC33
VCC12
Fig 9.1: Clock configuration
B
DVD: DVD-REF-A1 TITLE 1
CD: Playback a normal CDDA.
Common to all DVD-V compatible modules.
Check with DGND being the reference.
In case of NG, check the applicable line, the periphery of IC1501, soldering of the peripheral components and
defective components.
NO.
1
2
Check point 1 (stylus)
DACCK
DACCK
Media
DVD
CD
Specification value 1 Specification value 2
2.0 V~VCC33 V
DGND~0.8 V
2.0 V~VCC33 V
DGND~0.8 V
Specification value 3
36.864 0 MHz ± 300 ppm
33.868 8 MHz ± 300 ppm
Specification
value 1
C
Specification
value 2
Specification
value 3
GND
Fig 9.2: Clock specification value
D
E
F
66
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Side B
A
B
Check point 1 (DACCK stylus)
Side A
C
D
Check point 2 (IC1501 148 pin)
DGND2
E
Fig 9.3: 27 MHz, DACCLK check point
F
AVIC-Z110BT/XN/UC
5
6
7
8
67
1
2
3
4
Check 10: Is the audio circuit OK?
The serial 3 lines digital output + DACCLK, output from DVD-LSI (IC1501), are converted to analog audio
signal at Audio-DAC (IC1801) and are output from the HOST I/F (CN1901).
Simultaneously, the analog MUTE signal is also output from DVD-LSI (IC1501) via the HOST I/F.
The digital audio signal (IECOUT), output from DVD-LSI (IC1501).
A
CN1901
HOST I/F
IC1501
DVD-LSI
IECOUT
IC1801
Audio-DAC
LRCK
ADOUT
SRCK
LO
RO
GNDAU
B
Fig 10.1: Audio circuit
Playback DVD-REF-A1 TITLE 2 CHAPTER 1 (48 k/16 bit 1 kHz 0 dB),
and check with DGND being the reference.
In case of NG, check the applicable line, periphery of major components as described in the above drawing,
soldering of the peripheral components and defective components.
NO.
Check point 1 (stylus)
ADOUT3
SRCK
LRCK
1
2
3
C
Specification value 1
VCC33 V-0.6 V or higher
VCC33 V-0.6 V or higher
VCC33 V-0.6 V or higher
Specification value 2
0.4 V or lower
0.4 V or lower
0.4 V or lower
Reference waveform
Waveform 1
Waveform 2
Waveform 3
Specification
Specification value 2
value 1
GND
Fig 10.2: Serial 3 lines specification value
D
E
F
68
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Side A
A
B
DGND2
ADOUT
LRCK
Side B
C
D
SRCK
E
Fig 10.3: Serial 3 lines check points
F
AVIC-Z110BT/XN/UC
5
6
7
8
69
1
2
3
4
The following checks shall be conducted using the following measurement circuits with GNDAU1 being the reference.
47 kohm
47 kohm
A
LO
GNDAU1
RO
Check point 1 (stylus)
LO
RO
NO.
4
5
B
Specification value (rms)
1 400 ± 150 mV
1 400 ± 150 mV
Reference waveform
Waveform 4
Waveform 4
Specification value is the root-mean-square value (rms).
Fig 10.4: Analog audio out (LO, RO) specification value.
Side A
C
D
RO
LO
GNDAU1
Fig 10.5: Analog audio out check point
Check with DGND being the reference.
E
NO.
Check point 1 (stylus)
6 IEC
Specification value 1
VCC33 V-0.6 V or higher
Specification value 2
0.4 V or lower
Reference waveform
Waveform 5
F
70
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Side A
A
B
IEC
DGND2
Fig 10.6: Digital audio signal (IECOUT) check point
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
71
1
2
3
4
Check 11: Is the video circuit OK?
Composite signal and component signal are output from DVD-LSI (IC1501), and are output from the
HOST I/F (CN1901) via a buffer circuit.
A
CN1901
HOST I/F
IC1501
DVD_LSI
Video
DAC
section
Composite
B
COMPOSITE
Fig 11.1: Video circuit
Playback DVD-REF-A1 TITLE2 CHAPTER5 (WHITE 100%), and monitor COMPOSITE signal with
an oscilloscope with GNDV1 (stylus) being the reference. Set the trigger mode to “TV trigger” and
the trigger line to “150 line”.
Check point 1 (stylus)
NO.
1
C
Specification value
1 000 mVpp ± 5 %
COMPOSITE
Reference waveform
Waveform 6
In case of NG, check the applicable line, the periphery of the major components in the drawing above, soldering of the
peripheral components and defective components.
PEAK
Reference
value
COMPOSITE signal
Color burst
Pedestal level
BOTTOM
Horizontal sync signal
Fig 11.2: Waveform for the case of composite white 100% output
D
E
F
72
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Side A
A
B
COMPOSITE
GNDV
Fig 11.3: VIDEO signal check point
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
73
1
2
3
4
Check 12:How to judge whether the flash memory has reached its life or not.
If the reaction to user operation is slow or operation is slow in general, there is a possibility that the flash memory
has reached its life.
Make judgment regarding the flash memory life by looking at the display of the LD energizing time.
A
1.Let the LD energizing time displayed.
(Refer to the FE test mode for the method of displaying the LD energizing time.)
2.If the second digit from the left of the energizing time display is showing E,
such as “ E
”, it means that the flash memory has reached its life.
Example:
B
0E000BB8
C
D
E
F
74
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 13: 48 MHz Normal?
Each clock is created inside the IC1501 using the 48 MHz master crystal oscillator (X1501).
A
IC1501
DVD-LSI
X1950
48 MHz
crystal
USB_CLOCK
B
VCC33
VCC12
Fig 13.1: Clock configuration
Turn the power on, and check with DGND1 being the reference.
In case of NG, check the applicable line, periphery of IC1501,
soldering of the peripheral components and defective components.
NO.
2
Check point
Module No.
IC1501 50pin-DGND1
ALL
Specification value
48 MHz
± 50 ppm
Unit
ppm
C
Specification
value
GND
Fig 13.2: Clock specification value
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
75
1
2
3
4
Side A
A
IC1501 50pin
B
DGND1
Fig 13.3: 48 MHz check point
C
D
E
F
76
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
Check 14: Is USB Circuit OK?
The data is transmitted through D+, D- and SDA of HOST I/F while playing USB/IPOD.
USB memory uses only D+ and D-, but IPOD uses SDA (DATA) and SCL (CLOCK)
in addition to D+ and D-.
CN1901
HOST I/F
IC1501
CP_RESE
DVD-LSI
A
I2C_SDA
I2C_SCL
D+
DB
DGND
Fig. 14-1: USB Circuit
1.USB Memory: Play a song from USB memory and check D+ and D- with the DGND standards.
2.iPod: Connect iPod and check CP_RESET, SDA and SCL with the DGND standards until the pioneer log appears.
Play a song from iPod and check D+/D- with the DGND standards.
When it does not conform to the standards, check appropriate line, main parts shown in the above figure,
soldering of peripheral parts and malfunctions in parts.
No. Checking spot (stylus)
1 CP_RESET
2 SDATA
3 SCLOCK
4 D+
5 D-
C
Standard value 2
Standard value 1
VCC33*0.7or more
VCC33*0.7or more
VCC33*0.2 or less *Until the pioneer log appears after connecting the iPod
VCC33*0.7or more
VCC33*0.2 or less *Until the pioneer log appears after connecting the iPod
VCC33*0.7or more
VCC33*0.3 or less
VCC33*0.7or more
VCC33*0.3 or less
D
Standard value 2
Standard value 1
Fig. 14.2: USB Circuit Communication Wave
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
77
1
2
3
4
Side A
A
SDATA
CP_RESET
SCLOCK
B
D-
D+
DGND2
C
D
E
F
78
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
AUDIO
CH1:LO
CH2:RO
CH1:ADOUT3
Reference voltage: DGND2 1 V/div. 5 usec/div
A
Reference voltage: GNDAU2 1 V/div. 500 usec/div
G->
G->
G->
B
Waveform 1
Waveform 4
CH1:SRCK
CH1:IECOUT
Reference voltage: DGND2 1 V/div. 5 usec/div
Reference voltage: DGND2 1 V/div. 500 nsec/div
C
G->
G->
Waveform 2
Waveform 5
D
CH1:LRCK
Reference voltage: DGND2 1 V/div. 5 usec/div
G->
E
Waveform 3
F
AVIC-Z110BT/XN/UC
5
6
7
8
79
1
2
3
4
VIDEO
A
[WHITE 100IRE]
CH1:COMPO
Reference voltage: GNDV1 200 mV/div. 10 usec/div
B
Waveform 6
USB memory
USB memory
C
USB memory
Reference voltage:DGND 1 ms/div 2 V/div
Reference voltage:DGND 200 ns/div 2 V/div
D-
D-
DGND
D+
DGND
D+
D
Waveform 7
Waveform 8
E
F
80
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
iPod
iPod
iPod
A
Reference voltage:DGND 1 ms/div 2 V/div
Reference voltage:DGND 200 ns/div 2 V/div
D-
D-
DGND
D+
DGND
D+
B
Waveform 9
Waveform 10
iPod
iPod
Reference voltage:DGND 20 ms/div 1 V/div
Reference voltage:DGND 2 ms/div 1 V/div
CP_RESET
C
DGND
SDA
NRES
Waveform 11
Waveform 12
D
iPod
Reference voltage:DGND 500 us/div 1 V/div
E
SCL
Waveform 13
F
AVIC-Z110BT/XN/UC
5
6
7
8
81
1
2
3
4
5.4 ERROR CODE LIST
A
Error status
M e d ia E r r o r
Open
Read Error
Focus Error(Focus Error
in mechanism set u p)
B
00h
INCOMPATIBLE DEVICE
00h
UNPLAYABLE FILE
00h
(No display)
E R R O R -0 2 -9 9
E R R O R -0 2 -9 0
E R R O R -0 2 -9 E
Address no t
found(Invalid Track)
ERROR-02-80
Generation source
USB
USB
(MSC)
(iPod)
ACC
Off/On
Method of reset
Source
Eject
Off/On
Play Key
X
-
-
X
X
X
-
-
X
X
X
X
-
-
-
X
-
X
X
-
-
10h
20h
USB device of format alone that
cannot be reproduced
Door open error
Transfer start error
X
X
-
-
*
X
*
X
*
X
*
X
21h
Focus error
X
-
-
X
X
X
X
22h
Focus error during set up
(A focus has never been achieved
with that disc.)
X
-
-
X
X
X
X
Address not found.
X
-
-
X
X
X
X
X
-
-
X
X
X
X
X
-
-
X
X
X
X
X
-
-
X
X
X
X
23h
Spindle lock NG
(the disc cannot rotate)
Carriage home NG
(The pick up tries to return to carriage
home, but it cannot go back and stopped.)
ID/SUBCODE Read Error (ID/SUBCODE
cannot be read due to scratch or stain.)
AV CHIP decode NG
(AV chip cannot be decoded.)
24h
Carriage HOME
ERROR-02-92
25h
ID/SUBCODE Read Error
ERROR-02-94
26h
AV CHIP decode Error
ERROR-02-9A
2Ah
X
X
-
X
X
X
X
AV CHIP Recovery NG
ERROR-02-9B
2Bh
AV CHIP recovery NG
X
X
X
X
X
X
X
Error of PLAY BAC K
Mode Status
ERROR-02-9C
2Ch
Playback state error
(An error due to software bug.)
X
X
-
X
X
X
X
ERROR-02-9D
2Dh
Disc Data NG
X
-
-
X
X
X
X
X
-
X
-
-
-
X
-
-
*
*
*
*
X
X
-
X
-
-
-
X
X
X
-
Temp Error
(In Case of High
Tem perature )
No Disc
( including Disc loading
and e jectin g)
THERMAL
PROTECTION IN MOTION
(No display)
(No display)
30h
40h
50h
60h
61h
62h
High temperature
(Playback is stopped because the pick up
temperature is 89 C or higher.)
Disc has not been inserted.
(Including Load in process or
Eject in process.)
Loading mechanism error
(The disc cannot be clamped.)
Communication fault attesting iPod
iPod authentication data is abnormal
iPod attestation retrying failure
X
X
X
X
X
-
-
X
X
X
iPod attestation time out
E R R O R -0 2 -6 3
63h
iPod attestation time out
X
-
X
-
-
X
-
Error when iPod is connected/
It is generated STALL by the USB
communication
E R R O R -0 2 -6 4
64h
Error when iPod is connected/
It is generated STALL by the USB
communication
-
-
X
-
-
X
-
E R R O R -0 2 -6 5
65h
-
-
-
X
-
66h
-
-
X
-
-
X
-
E R R O R -0 2 -6 7
67h
-
-
X
-
-
X
-
E R R O R -0 2 -6 8
68h
Error setting iPod
Demand timeout when
initial is communicated
Protocol version
non-correspondence
Timeout when protocol
version is judged
-
E R R O R -0 2 -6 6
-
-
X
-
-
X
-
No songs error
-
-
X
-
-
X
-
-
-
X
-
-
X
-
-
-
X
-
-
X
-
-
-
-
-
X
-
-
-
X
-
-
X
-
X
-
-
-
-
Error setting iPod
Demand timeout when
initial is communicated
Protocol version
non-correspondence
Timeout when protocol
version is judged
(No display)
No songs error
iPod control forwarding/
Intarapta forwarding error
Demand timeout
iPod's reproducing
Remote switch error
Remote switch demand
timeout
D R M E rro r
F
USB device that doesn't correspond
Disc
ERROR-02-91
Loading_Mecha Error
E
Meaning
A disc containing the unplayable
Format only
Spindle Lock
Communication fault attesting iPod E R R O R -02-60
iPod authentication data is abnormal E R R O R -02-61
iPod attestation retrying failure E R R O R -02-62
D
UART
*2
NON-PLAYABLE DISC
Surface Error
Disc Data Error
C
OSD *1
69h
E R R O R -0 2 -6 A
6Ah
E R R O R -0 2 -6 B
6Bh
ERROR-02-6C
6Ch
ERROR-02-6D
6Dh
PROTECTED DISC
70h
NO ACCESSIBLE
DATA AVAILABL
70h
Region code Error NG
DIFFERENT REGION DISC
90h
C P R M *7 K e y E rro r *8
NON-PLAYABLE DISC
93h
REQUEST error
Failure in issuing read
command (chip dependent)
Adjustment of L0 is NG.
Adjustment of L1 is NG.
LD system NG
Gain adjustment system NG.
Gain determining system NG.
Servo initial setting related items NG.
Disc is not clamped yet.
Tracking system NG.
Media setting system NG.
Focus Error
Error of PLAY BAC K
Mode Status
Error of PLAY BAC K
Mode Status
Audio Propert y Timeou t
Error *9
ERROR-02-A0
A0h
E R R O R -0 2 -A 1
A1h
ERROR-02-A2
ERROR-02-A3
ERROR-02-A4
ERROR-02-A5
ERROR-02-A6
ERROR-02-A7
ERROR-02-A8
ERROR-02-A9
ERROR-02-AA
ERROR-02-AB
A2h
A3h
A4h
A5h
A6h
A7h
A8h
A9h
AAh
ABh
E R R O R -0 2 -B 0
E R R O R -0 2 -B 1
iPod control forwarding/
Intarapta forwarding error
Demand timeout
iPod's reproducing
Remote switch error
Remote switch demand
timeout
DRM error (All music cannot be played
back due to DRM.)
DRM error (All music cannot be played
back due to DRM.)
Region code NG (Unable to be played back
due to incorrect mechanism region.)
X
X
X
-
-
X
-
-
-
-
X
-
-
-
-
X
-
Key Error for playback
X
-
-
-
-
X
-
REQUEST error
Failure in issuing the read command
X
-
-
X
X
X
X
X
-
-
X
X
X
X
L0 adjustment is NG.
L1 adjustment is NG
LD system NG
Gain adjustment system NG.
Gain determining system NG.
Servo initial setting related items NG.
Disc is not clamped yet.
Tracking system NG
Media setting system NG
JUMP over layers NG
X
X
X
X
X
X
X
X
X
X
-
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
B0h
Navigation command error
X
-
-
X
X
X
X
B1h
Retry over
X
-
-
X
X
X
X
ERROR-02-C0
C0h
Audio property timeout error
X
-
-
X
X
X
-
Error when MCS is connected/
It is generated STALL by the USB
communication
ERROR-02-D0
D0h
Error when MCS is connected/
It is generated STALL by the USB
communication
-
X
-
-
-
X
CBW and CSW forwarding error
Audio class band securing failure
Audio class FS setting failure
Undefined Error
ERROR-02-D1
ERROR-02-D8
ERROR-02-D9
ERROR-FF-FF
D1h
D8h
D9h
FFh
CBW and CSW forwarding error
Audio class band securing failure
Audio class FS setting failure
Undefined error
X
X
-
X
X
-
X
X
82
-
-
X
X
X
X
X
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
X: Cancel the error by operation. -: Error is not cancelled by operation. *: No setting
*1 A content displayed on OSD. As for the items having multiple display patterns, the upper row is for the Japanese version Full GUI, and the lower row is for
the Touch Panel model and Full GUI (English version).
*2 A parameter of UART command, such as “receipt error notice”, that the DVD mechanism transmits.
*3 CPPM(Content Protection for Prerecorded Media) : A copyright protection technique used in DVD-A. The protection is realized by using the keys recorded
on the media and the device key held by the player.
*4 DVD-A compatible model only.
When an error has occurred, only the audio output will be muted but playback operation will continue. Furthermore, acceptance of the user operation will be
the same as usual.
*5 AWM (Audio WaterMark): Electronic watermark. Information on the copyright owner or CCI (copy control information) are recorded so that illegally copied
discs can be identified.
*6 Notice as an error status will not be given
*7 CPRM(Content Protection for Recordable Media) : A copyright protection technique for digital contents used for re-writable DVD or memory card.
(DVD-VR model only)
A
B
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
83
1
2
3
4
5.5 CONNECTOR FUNCTION DESCRIPTION
IP-BUS
iPod
A
RDS-TMC TUNER
6
5
4
3
2
1
B
10 : ACCDET
11 : A_RETURN
12 : V_RETURN
13 : VOUT
14 : RXiPod
15 : iACCPW
16 : ROUT
17 : GNDD
1 : USB2 : USB+
3 : ACCID
4 : USB5V
5 : USBGND
6 : NC
7 : LOUT
8 : NC
9 : TXiPod
1 : SWBUP
2 : RDSSNS
3 : TMC_MSN_ON
4 : CTOVICS
5 : VICSTOC
6 : GND
1. IPBUS+
2. IPBUSG
3. IPLG
4. NC
5. IPBUS6. IPRG
7. IPL+
8. ASENBO
9. IPR+
10. IPR11. IPL-
C
D
GPS ANTENNA
ANTENNA
MIC INPUT
AV CONNECTOR
POWER SUPPLY
1
16 14 12 10 8 6
4
2
15 13 11 9
3
1
E
2
3
4
5
6 7
8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
1 : FR+
2 : RR+
3 : FR4 : RR5 : FL+
6 : RL+
7 : FL8 : RL-
7
5
1 : TELMUTE
2 : KMODE
3 : PRR
4 : PRL
5 : SWL
6 : SWR
7 : PFR
8 : VTR2R
9 : VTR2L
10 : VTRIN2V
9 : PKB
10 : PULSE
11 : REV
12 : ILM
13 : AANT
14 : ACC
15 : GND
16 : BUP
11 : RROUT2
12 : RLOUT2
13 : BCV
14 : VTRIN3V
15 : RVOUT2
16 : BREMOTE
17 : EXTOC
18 : CTOEX
19 : (HYOKA)
20 : HRGND
21 : SWG
22 : HFGND
23 : PFL
24 : VTR2RG
25 : VTR2LG
26 : VTRIN2VG
27 : RROUT2G
28 : RLOUT2G
29 : BCVG
30 : VTR3VG
31 : RVOUT2G
32 : BGND
F
84
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
6. SERVICE MODE
6.1 TEST MODE
A
1. How to Select Test Mode Menu
Key operations used at the test mode are the following six keys;
Key Operation
Key Allocation
Cursor Up
VOL UP
Cursor Down
VOL DOWN
B
Page Change (Previous)
LEFT
Page Change (Next)
RIGHT
Item Selection (Determination)
MODE
Cancel /Return to previous page
HOME
2. How to Start-up Test Mode
C
Start-up by operation of the product.
1. Enter the following password while +B, ACC are ON (Normal application start-up status).
2. When the password is correct, restart begins and test mode menu is displayed.
1. Press [HOME] key.
2. Press keys in the order,
[RIGHT] -> [LEFT] -> [RIGHT] -> [LEFT] -> [RIGHT] -> [LEFT],
while pressing [HOME] key.
D
3. Release [HOME] key.
Start-up by SD card.
1. Download GGS1080 from the Service Site.
2. Decompress the file.
3. Copy the decompressed file to the SD card root.
4. Insert the SD card to the product and turn ACC on.
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
85
1
2
3
4
3. Test Mode Menu
A
B
Name of Test Item
Overview of Test
Display version information such as Navigation
Software, Navigation Destination, Microcomputer Software, etc.
Perform Error / Log View, File Copy and Clearing.
1 Version Information
2 Error / Log History
C
Writing of Navigation Program / Platform/Boot Loader /
IPL / System Microcomputer / BT Firmware.
Writing of Start-up Screen Data / APL Program.
Writing / Reading Fixed Data.
Writing / Reading / Clearing of BSP Backup Data.
Display connection status of System Microcomputer /
Mechanical Microcomputer / BT Module /
GPS_RF / iPod Authentication IC / One-Segment_RF.
Coordinate Test of touch panel.
3 Program Forced Write
4 SELF CHECK PROGRAM
5 TouchPanel Check
Perform Line Touch Panel and Calibration Tests.
6 Touch Panel Test
D
Perform Flicker Adjustment, Initialization of E2PROM.
Perform Service Test, E2PROM Test,
Backlight Test and Illumination Test.
Test of Hard Key.
7 Monitor TestMode
8 Key Test
Status display of Input Port.
Status display/changeover of Output Port.
Display drive information, disc scanning
(verification of volume).
File operation and file deletion.
Dumping display of file contents.
9 Port Test
10 Drive Maintenance
11 File Maintenance
E
F
86
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
A
B
Overview of Test
Name of Test Item
12 GPS INFORMATION
13 GPS assessment
14 GPS backup data clear
15 GYRO SENSOR INFO data clear
16 SENSOR test
17 Bluetooth Unit
18 NAND Test
19 USER'S AREA OF FLASH CLEAR
20 Audio Play Test
21 Image Test
Display GPS positioning data, satellite information
acquired and error information.
Version display of GPS driver / sensor.
Reset GPS driver and perform clearing of backup
data.
Clear the gyro-sensor learned value.
C
Display G-sensor, gyro value, power supply
voltage, temperature and installation status.
Perform radio wave authentication test.
Data readout of NAND FLASH.
Writing data or file into NAND FLASH.
Execution of User Area clearing.
Guiding Audio Line confirmation by the replay of
audio file.
Display various test images.
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
87
1
2
3
4
A
B
Name of Test Item
Overview of Tes
Display G Sensor, gyro value, power supply
voltage, temperature and variation, CAM_ON
terminal and installation status.
Confirmation of microphone input line for audio
recognition.
Confirmation of audio output line for SD / USB
Audio.
Confirmation of output for subwoofer pre-out.
22 EXT CONNECTION TEST
23 MIC LINE TEST
24 NAVI VOICELINE TEST
25 SUBWOOFER LINE TEST
C
Execution of ON/OFF for Fan Revolution,
controlling revolution speed.
Receiving test of wired remote control key.
Receiving test of manufacture code.
Setting of time
26 FAN CONTROL
27 WIRED REMOCON TEST
28 RTC TEST
Confirm the normal operation of USB device by
connecting USB device to the product.
Confirmation of normal operation of SD card.
29 USB CHECK
30 SD TEST
D
E
Name of Test Item
Overview of Test
Display images from iPod / AUX, VTR, external
terrestrial digital television.
Display image of back camera on navigation
screen.
Check wire connecting status of 3 color signals
for RGB key illumination.
Confirming flap close and displaying RPS value.
31 VTR INPUT TEST
32 BACK CAMERA TEST
33 RGB KEY ILLMINATION TEST
34 MechaClose Position Confirmation
F
Display product information.
35 PRODUCT INFORMATION
88
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
1. Version Information
Obtain version information for assigned software and display the information on
screen with list display.
A
1. Program Version [The first page]
Key Operation
Page Changeover (Prev. page)
Page Changeover (Next page)
Cancel / Return to prev. page.
Key Allocation
LEFT
RIGHT
HOME
B
C
Item
PLATFORM
Item Contents
Information Display
OS part version of system software [ *.****** ]: Value of Version
[NO_SET]: No information
IPL
Version of product startup program [ *.****** ]: Value of Version
[NO_SET]: No information
BOOTLOADER
Version of boot loader
[ *.****** ]: Value of Version
[NO_SET]: No information
MECHA VERSION Version of DVD mechanism
[ *.****** ]: Value of Version
[NO_SET]: No information
[ *.****** ]: Value of Version
APL PROGRAM
Version of navigation application
[NO_SET]: No information
CPU CORE
Version of CPU core
[ *.****** ]: Value of Version
SYSTEM uCOM
Version of system microcomputer
SYSTEM uCOM
BOOT PROGRAM
NAND CID
Version of startup program for
system microcomputer
Firmware ID of NAND Flash
D
[ *.****** ]: Value of Version
[NO_SET]: No information
[ *.****** ]: Value of Version
[NO_SET]: No information
[ *.****** ]: ID value
[ GET_NG ]: Acquisition failed
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
89
1
2
3
4
2. Model Information [The second page]
Key Operation
Page Changeover (Prev. page)
Page Changeover (Next page)
Cancel / Return to prev. page.
A
Key Allocation
LEFT
RIGHT
HOME
B
Item
PRODUCT NUMBER
C
NAVI INFORMATION
NAND DATA
PARTS CODE
NAND VERSION
VOLUME
INFORMATION
REGION CODE
D
Item Contents
Product Model Number
Information Display
[ AVIC-*** ]: Value of Version
[ NO_SET ]: No information
Planning Model Number
[ &XX*** ]: Value of Version
[ NO_SET ]: No information
Parts number of Data Set in [ CWW****- ]: Value of Version
NAND-FLASH
[ NO_SET ]: No information
Data Set Version of
[ PC5-*-* ]: Value of Version
NAND-FLASH
[ NO_SET ]: No information
Volume information of
[ Vol.* ]: Value of Version
NAND-FLASH
[ NO_SET ]: No information
Region Code of DVD
[ 2 ]: Europe / Normal Region Code
[ 1 ]: North America / Normal Region Code
[ 5 ]: Russia / Normal Region Code
[ 4 ]: Australia / Normal region Code
* Values other than above are abnormal values.
[ NO_SET ]: No information
E
F
90
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
3. Bluetooth Firmware Information [The third page]
Key Operation
Page Changeover (Prev. page)
Page Changeover (Next page)
Cancel / Return to prev. page.
Key Allocation
LEFT
RIGHT
HOME
A
B
Item
Item Contents
Bluetooth Firmware Bluetooth Firmware Version
Information Display
[ ****** ]: Value of Version
[ NO_SET ]: No information
C
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
91
1
2
3
4
2. Error/Log History
Perform displaying each error history, saving the history into storage and clearing the history.
A
Menu Screen
B
<>
VOL +/- : Item selection
MODE : Execution of selected item
HOME : Return to main menu
<- >
1. Error History Show
Display error history currently saved.
2. Log History Show
Display execution log history currently saved.
3. Error / Log History Save
Save histories of error, log and exception files into storage.
4. Error / Log History Delete
Clearing of error, log and exception histories saved.
C
1. Error History Show
<
D
E
Date
TickCount
Error Code
Error Line
Error Info 1, 2
Version Info
File
Log
F
92
: Time of error recorded
: Value of counter started counts at OS startup. 1 count is corresponding to 1 millisecond.
: Error code
: Number of lines on source code
: Additional Information
: Program version
Versions for boot loader, platform and application are displayed.
: Display file name where error happened.
: Log information (The content is displayed only when saved)
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
2. Log History Show
The execution log is the execution history when specific operation is performed. (Not errors)
A
<>
B
Date
: Time of error recorded
TickCount : Value of counter started counts at OS startup. 1 count is corresponding to 1 millisecond.
Log
: Log information
3. Error / Log History Save
C
Histories of error, log and exception are saved in storage.
<< Selection Screen>>
D
<>
VOL +/- : Item selection
DISP
: Execution of copy
HOME : Return to main menu
E
The history is saved in the following folder configuration;
SD or USB Memory
LOG
000
error.txt <- Error History
log.txt
<- Log History
AstLog
<- Exception History Folder
DBMSG000.log
SYSER000.log
EMERG000.log
EMERG001.log
(Histories may be saved up to EMERG511.log)
F
AVIC-Z110BT/XN/UC
5
6
7
8
93
1
2
3
4
4. Error / Log History Delete
Histories for error, log and exception are saved.
A
<>
B
3. Program Forced Write
C
D
<
- >
1. Navi Program Write
. . . Normally the following programs which perform
automatic version up are all written;
- Boot loader software
- Platform software
- Font data
- Application software
2. Platform Write
. . . Only platform software is written.
3. BootLoader Write
. . . Only boot loader software is written.
4. System uCom Write
. . . System microcomputer software is written.
5. Bluetooth Firmware Write . . . Firmware of Bluetooth chip is written.
E
* Normal writing becomes unable if power is off during the
writing. On this occasion, please retry firmware writing.
* "Complete" may not be displayed while the percentage is kept to 100%.
If "Complete" is not displayed in 1 minute after the percentage reaches 100%, turn
OFF and ON ACC, and then implement the writing of Bluetooth firmware again.
6. Opening Data Write
. . . Startup screen data is written.
F
94
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
<>
VOLUME +
VOLUME LEFT/UP
RIGHT/DOWN
MODE
HOME
. . . Nothing operates
. . . Nothing operates
. . . SD card is selected
. . . USB memory is selected
. . . Writing is started. * Valid only when the program is checked
. . . Operation returns to the program selection
A
[Writing of navigation program]
B
C
4. SELF CHECK PROGRAM
The connection status of function module installed in the product is displayed.
In the case of non-connection, error is displayed and the target module is considered to be fault.
D
E
Diagnostic Target
1
2
3
4
5
6
Target Unit
Check Content
System uCom
Mecha uCom
NAND Flash
GPS RF Unit
iPod Authentication Chip
Bluetooth Unit
Confirm connection status
Confirm connection status
Confirm connection status
Confirm connection status
Confirm connection status
Confirm communication
setup status
Required Time for
Diagnosis
Less than 1 second
Less than 1 second
Less than 1 second
Less than 1 second
Less than 1 second
Approx. 60 seconds,
max.
Indication
when OK
Connected
Connected
Connected
Connected
Connected
Connected
Indication
when NG
!!ERROR!!
!!ERROR!!
!!ERROR!!
!!ERROR!!
!!ERROR!!
!!ERROR!!
F
AVIC-Z110BT/XN/UC
5
6
7
8
95
1
2
3
4
5. Touch Panel Check
At the touch panel check, X, Y coordinates of location where touched are obtainable.
A
Screen under Checking
B
When touched, the coordination value where touched is displayed as well as vertical and
horizontal lines are illustrated with the cross point at the touched location.
The coordination value is set as the original point at upper-left and X coordinate to the right and
Y coordinate to the down, and maximum value of X coordinate is 800 and of Y coordinate is 480.
C
6. Touch Panel Test
The following two items are performed at the touch panel test;
1. Line Touch Panel Test
2. Calibration Test
3. User Calibration Confirmation
The line touch panel test is the test for determining whether touch panel is out of
alignment or not by depressing four points displayed on the screen.
At the calibration test, calibration adjustment is performed to compensate the
misalignment of the touch panel. User touches displayed 17 points in order and
correction is automatically performed after touching.
D
At the User Calibration Confirmation, it is displayed that whether the user has
executed calibration adjustment or not.
E
F
96
AVIC-Z110BT/XN/UC
1
2
3
4
5
6
7
8
1. Line Touch Panel Test
Touch the illustrated points in order.
If touched incorrectly, + mark is displayed in red.
When the touching proceeded to the final point of four (4), [OK] is displayed and the test is completed.
A
When depressing [HOME] key, [NG] is displayed and return to the menu screen.
The condition to be OK (move to the next point) when illustrated point is
touched is that the touched point should be within the following range;
10[dot]
If the touched point is within 10 dots from the center,
the touch is determined as valid.
B
10[dot]
10[dot]
10[dot]
2. Calibration Test
Touch the illustrated points in order.
Unlike the line touch panel test, move to the next point after touching.
You are not able to exit from the test until all 17 points are touched.
C
When touching on 17 points is completed and calibration is successful,
[FINISHED] is displayed and if the calibration is unsuccessful, [NG] is displayed.
Return to main menu with [HOME] key.
3. User Calibration Confirmation
The following is displayed when
User already performed calibration
User not performed yet calibration
Executed
Not executed
D
E
F
AVIC-Z110BT/XN/UC
5
6
7
8
97
1
2
3
4
7. Monitor Test Mode
Adjustment or test related to monitor is able to be performed.
A
Menu Screen
B
<
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.5
Linearized : Yes
Page Mode : UseOutlines
XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer : Acrobat Distiller 7.0.5 (Windows)
Create Date : 2009:05:22 14:31:19Z
Creator Tool : FrameMaker 7.2
Modify Date : 2009:07:03 09:34:04+09:00
Metadata Date : 2009:07:03 09:34:04+09:00
Format : application/pdf
Title : CRT4399-001
Creator : PMC
Document ID : uuid:054bb03a-9725-44da-8965-39e496313808
Instance ID : uuid:e3474ca7-d4d8-4d0a-a940-0a32083ee7d9
Has XFA : No
Page Count : 337
Page Layout : TwoColumnRight
Author : PMC
EXIF Metadata provided by EXIF.tools