Aiphone LEM 1DL Instructions

LEM-1DL to the manual 722345d3-445b-4798-b9cb-2ce7f040f586

User Manual: Aiphone LEM-1DL Instructions

Open the PDF directly: View PDF PDF.
Page Count: 4

#90111 1109
LEM-1DL Supplement
Pg. 1
The LEM-1DL master station provides communication to and from a door station, and has a separate button
for door release. This supplemental instruction manual addresses many of the additional functions and
modications for the LEM-1DL system, including installation and troubleshooting information.
LEM-1DL Supplemental Instructions
Single Master Station with Door Release
- REFER TO INSTALLATION MANUAL INSIDE LEM-1DL BOX FOR STANDARD
INSTALLATION INFORMATION -
MASTER STATION:
LEM-1DL: 1-call master station with “Normally Open” door release button
DOOR STATIONS:
(Note: Door stations are weather resistant, made for outdoor use)
LE-D: Surface mount, plastic door station (included with LEM-1DLS Set)
LE-DA: Flush mount in 2-gang box, stainless steel cover
LS-NVP/C: Vandal resistant ush mount in 3-gang box, white powder-coat nish
LE-SS: Vandal resistant ush mount sub in 2-gang box, stainless steel
LE-SSR: Vandal resistant, red mushroom button, ush mount in 2-gang box,
stainless steel
LE-SS-1G: Vandal resistant ush mount sub in 1-gang box, stainless steel
OPTIONAL COMPONENTS & ACCESSORIES:
RY-AC/A: External signaling relay (Requires 12VDC power supply)
DAK-2S: Dual master adaptor kit
(1 per 2 master stations. Use 2 DAK-2S for up to 4 total master stations)
SBX-NVP: Surface mount box for LS-NVP/C
SBX-2G: Surface mount box for LE-SS, LE-SSR, LE-DA
SBX-1G-SS: Surface mount box for LE-SS-1G
EL-12S: Door strike (for interior wood frame doors only)
PT-1210N: AC 12V Transformer (used for door strike and for each master station)
PS-1225UL: 12V DC Power Supply, 2.5A, UL Listed
822202: 2 conductor, 22AWG, Shielded wire
(Available in 500’ and 1000’ boxes)
Install two separate runs of this cable, one for the intercom and one for
the door release.
DOOR RELEASE WIRES MUST BE IN A SEPARATELY JACKETED CABLE FROM THE INTERCOM WIRING.
LEM-1DLS Set contains:
1 LEM-1DL, 1 LE-D, 1 PT-1210N.
Door strike not included.
2 cond. shielded for intercom
LEM-1DL
LE-D LE-DA
LS-VNP/C LE-SS
DAK-2S
(2 component modules per kit)
Separate 2 conductor for door release
If using a non-Aiphone door strike, use separate power
source for door release mechanism.
LE-D
LEM-1DL
PT-1210N
Power
Source
for Strike
!
Please read and understand all
instructions before installation.
LEM-1DL Supplement
Pg. 2
WIRING DIAGRAM: Dual Master LEM-1DL System with DAK-2S Dual Master Adaptor
OPERATION NOTES:
1. Only one master can be used at a time.
2. If both masters are activated, a feedback (squeal) will be heard through the system when either TALK button is pressed.
3. If feedback occurs, press the OFF button on one of the LEM-1DL masters.
INSTALLATION GUIDELINES:
1. Use 2 conductor shielded wire from the door station to the rst master, then to the second master.
2. Install the units at the desired locations.
3. Separate PT-1210N power supplies are required for each master station. NOTE: Connect power leads to master BEFORE plugging in power supply
4. Install the bare wire leg of the component module directly onto the “1” terminal of the LEM-1DL’s.
5. Attach the wire coming form the “1” terminal of the LE-D to the colored wire end of the component modules at both masters. (The component
modules will easily t within the space available.)
6. Connect the “E” terminals between the door station and master stations.
7. If door release is included, use a separate 2-conductor wire from the “EL” terminals of the masters through an AC transformer and to the door strike.
8. The EL-12S is designed for a standard wood framed door, and for light and medium usage. If a different type of door is used, install a strike
appropriate for the door.
9. The door release button on the master station is a “Normally Open” contact closure. Contact rating is 30V AC/DC @ 1 Amp.
IMPORTANT!!!
Each master REQUIRES an individual power supply.
1
E E
-
1
EL
EL
+
E
-
1
EL
EL
+
-
4 LEM-1DL Master Stations with 1 Door Note: In a multi-master system, all masters only talk to the
door station, and only one master can be on at a time
LE-D LEM-1DL LEM-1DL LEM-1DL LEM-1DL
Component
Module
Component
Module
Component
Module
Component
Module
PT-1210N PT-1210N PT-1210N PT-1210N
LE-D LEM-1DL
PT-1210N
LEM-1DL
PT-1210N
Component
Module Component
Module
Leave
E/- jumper
attached
If using a non-Aiphone door strike,
use a separate power source for the
door release mechanism.
!
Aiphone EL-12S
1
E
-
E
-
1
EL
EL
+
E
-
1
EL
EL
+
1
E
-
1
EL
EL
+
E
-
EL
EL
+
Door Strike
Power Source
for door strike
1
E
-
E
-
1
EL
EL
+
-
RY-AC
BELL
LE Series Sub LEM-1DL
+
-
LOCK
POWER
RY-18L / RY-24L
Magnetic Lock
COM
N/C
Brn
Org
Yel
Blk
Red
Use Brown & Yellow wires
when connecting to a Maglock. LEM-1DL Supplement
Pg. 3
WIRING DIAGRAM: LEM-1DL System with External Signaling using RY-AC Relay
MAGNETIC LOCK WIRING METHOD:
(Normally Closed Contact)
Lock Power: Power source for Magnetic Lock
When using 12-18V DC, use the RY-18L
When using 24-36V DC, use the RY-24L
Leave
E/- jumper
attached
Leave
E/- jumper
attached
+
1
E
-
E
-
1
EL
EL
+
SYSTEM CONFIGURATION:
LEM-1DL with Door Release contact activating a Normally Closed relay for a Magentic Lock
Note: For applications requiring a Normally Closed (N/C) contact (Magnetic locks, etc.), an external
relay should be chosen based on the lock’s power source.
- When using a 12-18V DC magnetic lock, Aiphone’s RY-18L relay may be used.
- For 24V DC magnetic locks, Aiphone’s RY-24L relay may be used.
- A 3rd party relay of similar specications may also be used. Refer to manufacturer’s
documentation for connection details.
Normally Open Dry
Contact to door
strike and power
Component Module
If a DAK-2S is not available, install components as shown below.
Capacitor: 25V, 15-33ufd Non-polarized
Diode: 1N4148
Output of RY-AC (Yellow
wires) provide a momentary
dry contact closure while
the call button on the door
station is being pressed.
PS-1225UL
NOTE: Intercom must be
powered with a 12VDC
power suplly when RY-AC
is connected.
LEM-1DL
Component
Module
LE-D
White
Red
Black
Power source
for bell
To 1 of LE-D and
WHITE wire of RY-AC To 1 of LEM-1DL
INSTALLATION TIPS:
1. Use shielded wire for the communication path, and ground one end of the shield to an earth ground.
2. Run intercom wire at least 20” away from AC wiring, uorescent lights or dimmer switches.
3. Keep intercom cable away from alarm, data, phone, and video cables.
4. Door release wires must be in a separately jacketed cable from the intercom wires. Use two separate
cables; one for audio and one for door release.
5. When installing a second master station, wire must be run from the rst master station, not from the
door station. See diagram on page 2.
6. Do not install master station near light switches, dimmer switches, or other devices that may cause
interference with the intercom system.
7. Do not install the master station on the opposite wall from the door station. If the units are too close,
acoustical feedback may result.
TROUBLESHOOTING GUIDE:
Aiphone Communcation Systems
1700 130th AVE N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:
1-800-692-0200
E-mail tech@aiphone.com
LEM-1DL Supplement
Pg. 4
#90111
1109JD
PROBLEM POSSIBLE CAUSE SOLUTION
No call tone from door to master station.
(A) OFF button on master not pressed.
(B) E/- jumper not attached.
(A) Press OFF button on master. If call tone still doesn’t come
through, read solution (B).
(B) Make sure jumper is attached to E/- terminals on door
station (or proper wires jumpered on LS-NVP, LE-SS subs).
Wire from E/- should be connected to E of master.
No communication from door station. E/- jumper not attached
Ensure that the jumper at the door station is attached between
E and - terminals
No call tone, no communication. Chirping
sound when volume control is turned all the
way up. Wrong voltage on LEM-1DL
Check power supply. If it’s a model SKK-620, remove and
replace with model PT-1210N. Verify that voltage on +/-
terminals is between 12-16V AC or 12-24V DC.
In a system with RY-AC and external signaling
device connected, the external device is
activated every time TALK button is pressed.
DAK-2S component module missing or
installed incorrectly.
Make sure the component module is installed with the bare
wire under the 1 terminal and the white wire of the RY-AC
spliced to the colored wire.
In a dual master system, call tone is heard
at the second master when pushing the talk
button on one master.
Missing DAK-2S dual master adaptor
kit.
Install 1 component module from the DAK-2S at each master.
See Pg. 2. If DAK-2S is not available, connect specied diode
and capacitor in parallel and install as shown on PG. 3.
In a dual master system, feedback occurs
when pressing the talk button.
One power supply is used for both
masters.
Ensure that each master has its own power supply. Use any
power supply with output between 12-16V AC or 12-24V DC.
Aiphone recommends the PT-1210N.
AC noise when listening to the door station Intercom wiring run close to AC wiring.
Ensure that the intercom wire is run at least 20” from any AC
electircal wire, or crossed at 90 degrees. Intercom wire should
be shielded, with the drain wire connected to an earth ground
at the master end.
AC noise when talking to the door station
Power wires run with communication
wires.
Ensure that power wires coming from the PT-1210N are not
run in the same jacket cable with the communication wires run
to the door.

Navigation menu