BVM D14H1U_Maintenance Manual BVMD14H1
User Manual: BVMD14H1
Open the PDF directly: View PDF 
.
Page Count: 158
| Download | |
| Open PDF In Browser | View PDF |
TRINITRON® COLOR VIDEO MONITOR BVM-D14H1A BVM-D14H1E BVM-D14H1U BVM-D14H5A BVM-D14H5E BVM-D14H5U CHASSIS NO. SCC-P31A-A CHASSIS NO. SCC-G10B-A CHASSIS NO. SCC-G09D-A CHASSIS NO. SCC-P31B-A CHASSIS NO. SCC-G10C-A CHASSIS NO. SCC-G09E-A MAINTENANCE MANUAL 1st Edition Serial No. 2000001 and Higher (ALL MODELS) ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen. ! AVERTISSEMENT Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. WARNING!! ATTENTION!! AN INSULATED TRANSFORMER SHOULD BE USED DURING ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BECAUSE OF LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE AC POWER LINE. AFIN D’ÉVITER TOUT RISQUE D’ÉLECTROCUTION PROVENANT D’UN CHÂSSIS SOUS TENSION, UN TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÉ LORS DE TOUT DÉPANNAGE. LE CHÂSSIS DE CE RÉCEPTEUR EST DIRECTEMENT RACCORDÉ Á L’ALIMENTATION SECTEUR. SAFETY-RELATED COMPONENT WARNING !! ATTENTION AUX COMPOSANTS RELATIFS Á LA SÉCURITÉ!! COMPONENTS IDENTIFIED BY A ! MARK ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. LES COMPOSANTS IDENTIFIÉS PAR UNE MAPQUE ! SUR LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMÉRO DE PIÈCE EST INDIQUÉ DANS LE PRÉSENT MANUEL OU DANS DES SUPPLÉMENTS PUBLIÉS PAR SONY. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ. Table of Contents 1. Operating Instructions BVM-D9H1J/D9H1U/D9H1E/D9H1A/D9H5J/D9H5U/D9H5E/D9H5A D14H1J/D14H1U/D14H1E/D14H1A/D14H5J/D14H5U/D14H5E/D14H5A ..................................................................................................................... 1-1 2. Service Informations 2-1. Circuit Boards Location .............................................................................. 2-1 2-2-1. Cabinet and Rear Panel Removal ............................................... 2-2 2-2-2. How To Open The B Board ....................................................... 2-3 2-2-3. Bezel Complete Assy Removal .................................................. 2-3 2-2-4. HA, HB and HC Boards Removal (D14H5) .............................. 2-4 2-2-5. YA, YB and YC Boards Removal ............................................. 2-5 2-2-6. G Board Removal ....................................................................... 2-5 2-2-7. BX Board (BKM-129X) Removal and Check ........................... 2-6 2-2-8. T Board Removal ....................................................................... 2-7 2-2-9. M Block Assy (MA and MB Boards) Removal ......................... 2-8 2-2-10. Picture Tube Removal ................................................................ 2-9 3. Set-Up Adjustments 3-1. Set-Up Adjustment When CRT is Replaced ............................................... 3-1 [Focus Adjustment] ..................................................................................... 3-3 [Landing Adjustment] ................................................................................. 3-5 [H Blanking Adjustment] ............................................................................ 3-6 [V Blanking Adjustment] ............................................................................ 3-7 [Linearity Adjustment] ................................................................................ 3-8 [Convergence Adjustment] ....................................................................... 3-10 [Static Convergence Adjustment] ............................................................. 3-10 [Dynamic Convergence Adjustment] ........................................................ 3-11 [G2 Adjustment] ........................................................................................ 3-11 [White Balance Adjustment] ..................................................................... 3-12 4. Safety Related Adjustments +B (135 V) Voltage Check ........................................................ 4-2 High Voltage Regulator Check .................................................. 4-2 High Voltage Hold-Down Check ............................................... 4-3 Beam Current Protector Check .................................................. 4-3 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1 5. Circuit Adjustments 5-1. B Board Adjustments .................................................................................. 5-1 1. RGB Signal Adjustment ............................................................. 5-2 2. 15k YPBPR SMPTE (709) Signal Adjustment .......................... 5-3 3. 15k YPBPR SMPTE (601) Signal Adjustment .......................... 5-5 4. 15k YPBPR BETACAM SETUP 0 (601) Signal Adjustment ... 5-6 5. 15k YPBPR BETACAM SETUP 7.5 (601) Signal Adjustment 5-7 6. 33k YPBPR SMPTE (709) Signal Adjustment .......................... 5-8 6. Circuit Descriptions 6-1. 6-2. 6-3. 6-4. 6-5. 6-6. G Board ....................................................................................................... 6-1 G1 Board ..................................................................................................... 6-4 B Board ....................................................................................................... 6-4 C Board ....................................................................................................... 6-6 MA Board .................................................................................................... 6-6 MB Board .................................................................................................... 6-6 7. Semiconductors ............................................................. 7-1 8. Exploded Views 8-1. 8-2. 8-3. Bezel, Cabinet ............................................................................................. 8-1 M Block, Signal Block ................................................................................ 8-2 Picture Tube, Chassis .................................................................................. 8-3 9. Electrical Parts List ........................................................ 9-1 10. Block Diagrams Overall (1/2) .............................................................................................. 10-1 Overall (2/2) .............................................................................................. 10-2 B (1/2), BX, B1, B2 .................................................................................. 10-3 B (2/2), C ................................................................................................... 10-4 G (1/2) ....................................................................................................... 10-5 G (2/2), G1 ................................................................................................ 10-6 MA, MB .................................................................................................... 10-7 HA, HB, HC .............................................................................................. 10-8 2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 11. Diagrams 11-1. Frame Schematic Diagrams ...................................................................... 11-2 11-2. Schematic Diagrams and Printed Wiring Boards ...................................... 11-3 Schematic Diagrams BX (1/2) .................................................................................................. 11-4 BX (2/2) .................................................................................................. 11-5 B (1/4) .................................................................................................. 11-7 B (2/4) .................................................................................................. 11-8 B (3/4) .................................................................................................. 11-9 B (4/4) ................................................................................................ 11-10 B1 ................................................................................................ 11-12 B2 ................................................................................................ 11-13 C ................................................................................................ 11-14 G (1/3) ................................................................................................ 11-17 G (2/3) ................................................................................................ 11-18 G (3/3) ................................................................................................ 11-19 G1 ................................................................................................ 11-21 HA ................................................................................................ 11-23 HB ................................................................................................ 11-24 HC, HD ................................................................................................ 11-26 MA ................................................................................................ 11-29 MB ................................................................................................ 11-31 YA, YB, YC .......................................................................................... 11-32 T ................................................................................................ 11-33 Printed Wiring Boards BX .................................................................................................. 11-3 B .................................................................................................. 11-6 B1 ................................................................................................ 11-12 B2 ................................................................................................ 11-13 C ................................................................................................ 11-14 G ................................................................................................ 11-15 G1 ................................................................................................ 11-21 HA ................................................................................................ 11-22 HB ................................................................................................ 11-24 HC ................................................................................................ 11-25 HD ................................................................................................ 11-26 MA ................................................................................................ 11-28 MB ................................................................................................ 11-30 YA, YB, YC .......................................................................................... 11-32 T ................................................................................................ 11-33 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3 4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A TRINITRON® COLOR VIDEO MONITOR 1-1 This section is extracted from operation manual. OPERATION MANUAL [Japanese/English] 1st Edition Serial No. 2000001 and Higher Section 1 Operating Instructions BVM-D9H1J/D9H1U/D9H1E/D9H1A BVM-D9H5J/D9H5U/D9H5E/D9H5A BVM-D14H1J/D14H1U/D14H1E/D14H1A BVM-D14H5J/D14H5U/D14H5E/D14H5A 1-2 To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. ATTENTION Il y a un risque d’explosion si la pile est mal insérée. Remplacer la pile uniquement par une pile de même type ou de type équivalent recommandé par le fabricant. Jeter les piles usées conformément aux instructions du fabricant. AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié. WARNUNG Um Feuergefahr und die Gefahr eines elektrischen SchIages zu vermeiden, darf das Gerät weder Regen noch Feuchtigkeit ausgesetzt werden. Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur einem Fachmann. ADVERTENCIA Para evitar incendios o el riesgo de electrocución, no exponga la unidad a la lluvia ni a la humedad. VORSICHT: Es besteht Explosionsgefahr, wenn die Batterie inkorrekt eingelegt wird. Es darf nur eine identische oder eine vom Hersteller empfohlene Batterie des gleichen Typs eingesetzt werden. Entladene Batterien sind nach den Anweisungen des Herstellers zu entsorgen. PRECAUCION Peligro de explosión en caso de haberse instalado incorrectamente la betería. Cambie sólo por una del mismo tipo o especificaciones equivalentes, de entre las recomendadas por el fabricante. Las baterías viejas se deben eliminar siguiendo las instrucciones del fabricante. ATTENZIONE: Pericolo di esplosione se la pila viene sostituita scorrettamente. Sostituirla solo con un’altra uguale o di un tipo equivalente consigliato dal fabbricante. Gettare via le pile usate secondo le istruzioni del fabbricante. For customers in the USA (BVM-D9H1U/D9H5U, BVM-D14H1U/D14H5U) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. Für Kunden in Deutschland Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Voor de klanten in Nederland Para evitar descargas eléctricas, no abra la unidad. En caso de avería, solicite los servicios de personal cualificado. ATTENZIONE Per evitare incendi o cortocircuiti, l’apparecchio non deve essere esposto alla pioggia o all’umidità. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Per evitare scosse elettriche, non aprite l’apparecchio. Per le riparazioni rivolgetevi solo a personale qualificato. Note The socket-outlet should be installed near the equipment and be easily accessible. Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. Remarque La prise doit être près de l’appareil et facile d’accès. Hinweis Zur Trennung vom Netz ist der Netzstecker aus der Steckdose zu ziehen, welche sich in der Nähe des Gerätes befinden muß und leicht zugänglich sein soll. Nota La toma mural debe estar instalada cerca del equipo y debe accederse a ésta con facilidad. Nota La presa di corrente deve essere situata vicino all’apparecchio e deve essere facilmente accessibile. • Dit apparaat bevat een Li-ion batterij voor memory back-up. • De batterij voor memory back-up is vastgesoldeerd op de MA printplaat BT1. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat bij einde levensduur afdankt. • Gooi de batterij niet weg, maar lever hem in als KCA. För kunderna i Sverige Apparaten ma kun tilkoples jordet stikkontakt For kunder i Norge Apparatet må kun tilkoples jordet stikkontakt For the customers in Europe (BVM-D9H1E/D9H1A/D9H5E/D9H5A, BVM-D14H1E/ D14H1A/D14H5E/D14H5A) This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European standards: • EN60950: Product Safety • EN55103-1: Electromagnetic Interference (Emission) • EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment(s): E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors) and E4 (controlled EMC environment, ex. TV studio). Pour les clients européens (BVM-D9H1E/D9H1A/D9H5E/D9H5A, BVM-D14H1E/ D14H1A/D14H5E/D14H5A) Ce produit portant la marque CE est conforme à la fois à la Directive sur la compatibilité électromagnétique (EMC) (89/ 336/CEE) et à la Directive sur les basses tensions (73/23/ CEE) émises par la Commission de la Communauté européenne. La conformité à ces directives implique la conformité aux normes européennes suivantes: • EN60950: Sécurité des produits • EN55103-1: Interférences électromagnétiques (émission) • EN55103-2: Sensibilité électromagnétique (immunité) Ce produit est prévu pour être utilisé dans les environnements électromagnétiques suivants: E1 (résidentiel), E2 (commercial et industrie légère), E3 (urbain extérieur) et E4 (environnement EMC contrôlé ex. studio de télévision). Für Kunden in Europa (BVM-D9H1E/D9H1A/D9H5E/D9H5A, BVM-D14H1E/ D14H1A/D14H5E/D14H5A) Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt sowohl die EMV-Direktive (89/336/EEC) als auch die Direktive Niederspannung (73/23/EEC) der EGKommission. Die Erfüllung dieser Direktiven bedeutet Konformität für die folgenden Europäischen Normen: • EN60950: Produktsicherheit • EN55103-1: Elektromagnetische Interferenz (Emission) • EN55103-2: Elektromagnetische Empfindlichkeit (Immunität) Dieses Produkt ist für den Einsatz unter folgenden elektromagnetischen Bedingungen ausgelegt: E1 (Wohnbereich), E2 (kommerzieller und in beschränktem Maße industrieller Bereich), E3 (Stadtbereich im Freien) und E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio) English WARNING BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Table of Contents ATTENTION - When the product is installed in a rack: a) Elevated operating ambient temperature If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacture’s maximum rated ambient temperature (Tmra: 0°C to 35°C (32°F to 95°F)). b) Reduced air flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. c) Mechanical loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. d) Circuit overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. e) Reliable earthing Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips). f) Gap keeping Upper and lower gap of rack-mounted equipment should be kept at least 44 mm (1 3⁄4 inches). For the customers in the United Kingdom (BVM-D9H1E/D9H1A/D9H5E/D9H5A, BVM-D14H1E/ D14H1A/D14H5E/D14H5A) WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly - if you are in any doubt consult a qualified electrician. Achtung - bei Installation des Geräts in einem Gestell: a) Erhöhte Umgebungstemperatur bei Betrieb Wird das Gerät in einem geschlossenen Gestell oder einem Gestell mit mehreren anderen Geräten installiert, kann die Umgebungstemperatur um das Gestell höher sein als die normale Umgebungstemperatur im Raum. Achten Sie daher bitte besonders darauf, das Gerät in einer Umgebung zu installieren, in der die Temperatur nicht über die vom Hersteller angegebene Umgebungstemperatur von 0 bis 35 °C (32 °F bis 95 °F) ansteigt (Tmra). Chapter 1 Overview Precautions ........................................................................................ 3(E) Overview ............................................................................................ 4(E) Features ..................................................................................... 4(E) Options ...................................................................................... 5(E) Location and Function of Parts ....................................................... 7(E) BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Front Panel ...................................................................................7(E) BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Rear Panel .................................................................................12(E) BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Front Panel .......................................................................16(E) BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Rear Panel ........................................................................ 21(E) Installation of the 4:3 Mask ........................................................... 24(E) BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A .................................................. 24(E) BVM-D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A ............................................24(E) Chapter 2 Menu Basic Menu Operations .................................................................. 25(E) Menu Operation Buttons .........................................................25(E) Displaying the Menus.............................................................. 26(E) Menu Operation.......................................................................26(E) ADDRESS Menu ....................................................................29(E) Menu Structure ............................................................................... 30(E) A Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ Menu ..................................... 31(E) Overview .................................................................................31(E) Structure of the CONTROL PRESET ADJ Menu ..................31(E) Setting Lists in the CONTROL PRESET ADJ Menu .............31(E) B Adjusting the Color Temperature — COLOR TEMP ADJ Menu ............................................... 33(E) Overview .................................................................................33(E) Structure of the COLOR TEMP ADJ Menu ........................... 33(E) Setting Lists in the COLOR TEMP ADJ Menu ......................34(E) C Setting the Input Configuration — INPUT CONFIG Menu...................................................... 35(E) Overview .................................................................................35(E) Structure of the INPUT CONFIG Menu .................................35(E) Setting Lists in the INPUT CONFIG Menu ............................ 36(E) D Assigning the Remote Control Functions — REMOTE Menu ................................................................. 37(E) Overview .................................................................................37(E) Structure of the REMOTE Menu ............................................37(E) Setting Lists of the REMOTE Menu ....................................... 38(E) b) Reduzierte Belüftung Das Gerät muß so im Gestell installiert werden, daß eine Belüftung gewährleistet ist, die für den sicheren Betrieb des Geräts erforderlich ist. c) Mechanische Belastung Das Gerät muß so im Gestell installiert werden, daß nicht durch eine ungleichmäßige mechanische Belastung Unfallgefahr entsteht. d) Überlastung der Stromkreise Der Anschluß des Geräts an das Versorgungsnetz erfordert sorgfältige Planung. Bitte beachten Sie insbesondere die Auswirkungen, die eine Überlastung der Stromkreise im Hinblick auf den Überspannungsschutz und die physischen Komponenten des Versorgungsnetzes haben kann. Beachten Sie in diesem Zusammenhang unbedingt die Angaben auf dem Typenschild am Gerät. e) Zuverlässige Erdung Geräte, die in einem Gestell installiert werden, benötigen eine zuverlässige Erdung. Achten Sie insbesondere auf Anschlüsse an das Versorgungsnetz, die nicht direkt an einen Abzweigstromkreis, sondern indirekt, zum Beispiel über Verlängerungskabel, erfolgen. f) Erforderliche Abstände Halten Sie zur Ober- und Unterseite eines in einem Gestell installierten Geräts einen Abstand von 44 mm (1 3/4 inches) ein. (Continued) 1 (E) 1-3 1-4 Precautions Table of contens Chapter 3 Appendix E Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu .................................... 39(E) Overview .................................................................................39(E) Structure of the SYSTEM CONFIG Menu .............................40(E) Setting Lists of the SYSTEM CONFIG Menu........................40(E) F Displaying Information About the Monitor — STATUS Menu ................................................................... 42(E) Overview .................................................................................42(E) Structure of the STATUS Menu..............................................42(E) Setting Lists of the STATUS Menu ........................................ 42(E) G Adjusting the Position, Size and Geometry of the Picture — ALIGNMENT Menu .......................................................... 43(E) Overview .................................................................................43(E) Structure of the ALIGNMENT Menu ..................................... 43(E) Setting Lists of the ALIGNMENT Menu ...............................43(E) Selecting the Monitor to Control — ADDRESS Menu ............... 45(E) Overview .................................................................................45(E) Displaying the ADDRESS Menu ............................................45(E) Cancelling the Remote Control Mode ..................................... 46(E) Exiting the ADDRESS Menu .................................................. 46(E) Short-cut Function in the ADDRESS Menu ........................... 46(E) Specifications ................................................................................... 47(E) Available Signal Format..........................................................53(E) Connection Cable Specifications for Color Temperature Probes..........................................54(E) Menu Index ..................................................................................... 56(E) Menu Configuration ....................................................................... 58(E) On safety On cleaning • Operate the unit only with a power source as specified in “Specifications” section. • The nameplate indicating operating voltage, power consumption, etc., is located at the rear. • Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further. • Do not drop or place heavy objects on the power cord. If the power cord is damaged, turn off the power immediately. It is dangerous to use the unit with a damaged power cord. • Unplug the unit from the wall outlet if it is not to be used for several days or more. • Disconnect the power cord from the AC outlet by grasping the plug, not by pulling the cord. • The socket-outlet shall be installed near the equipment and shall be easily accessible. • Use the supplied AC adaptor for the BVM-D9H1U/ D9H1E/D9H1A/D9H5U/D9H5E/D9H5A models only. It is dangerous to use the AC adaptor for models other than these. To keep the unit looking brand-new, periodically clean it with a mild detergent solution. Never use strong solvents such as thinner or benzine, or abrasive cleansers since they will damage the cabinet. As a safety precaution, unplug the unit before cleaning it. On installation • Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. • Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. On mounting the rack BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A When the monitor is mounted on the rack, the proximity of other equipment or a decrease in air circulation may cause heat to build up inside the monitor. Therefore, when mounting the monitor on the rack, ensure there is an adequate opening for ventilation or install a fan. The following operating conditions are needed: Temperature: 0°C to 35°C (32°F to 95°F), Optimum temperature: 20°C to 30°C (68°F to 86°F) On the battery (BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A only) The MAIN POWER switch is not supplied with the above models. Therefore, when the power is turned off with a battery installed, the monitor is set to standby mode and a small amount of power is consumed. When the monitor is not used for a long period, remove the battery. 2 (E) On repacking Do not throw away the carton and packing materials. They make an ideal container which to transport the unit. If you have any questions about this unit, contact your authorized Sony dealer. On magnetism • Do not place the unit near any objects or pieces of equipment which generate magnetism, such as magnets, speakers, electric clocks, toys using magnets, health appliances, etc. Magnetism will cause picture bounce, oscillations or picture discoloration. • Also, the picture may become fuzzy or the colors may not reproduce correctly due to earth magnetism. This depends on direction that the unit is installed. This is not equipment failure. In such a case, simply degauss the unit. On the CRT • Dust accumulates on the CRT easily. Clean the CRT when necessary with a soft cloth. The surface of the CRT is easily scratched; therefore, do not rub or touch the surface of the CRT unnecessarily since this may result in a scratched picture tube. • If you touch the surface of the CRT, you may feel a weak electrical shock. This is simply static electricity that is generated on the surface of the CRT. It will not affect the human body. On using as the monitor for 4:3 signals The 16:9 mask is installed at the factory. When the display is set to the 4:3 aspect ratio, the upper and lower portions of the display are masked and you cannot view the upper and lower portions of the picture. Therefore, when you want to display the picture in 4:3 aspect ratio, install the supplied 4:3 mask. 3 (E) 1 Overview Chapter 1Chapter Overview Chapter 2 Menu The BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A are 9 -inch Trinitoron®1) Color Monitors. The BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/ D14H5A are 14-inch2) Trinitoron® Color Monitors. Features Multiformat The monitor supports the principal format (480I/480P/ 720P/1080I) for the digital broadcasts, NTSC and PAL color systems, and a wide variety of signals3) whose horizontal frequency is between 15 kHz and 45 kHz. High resolution picture tube The HR Trinitron picture tube produces a clear, high resolution image. Aperture grille pitch Resolution at the center of the picture BVM-D9H1U/ D9H1E/D9H1A/ D9H5U/D9H5E/ D9H5A 0.25 mm 450 TV lines (4:3) 340 TV lines (16:9) BVM-D14H1U/ D14H1E/D14H1A/ D14H5U/D14H5E/ D14H5A 0.25 mm Model 800 TV lines (4:3) 600 TV lines (16:9) Separate control unit (BVM-D9H1U/D9H1E/ D9H1A/D14H1U/D14H1E/D14H1A) Using a separate control unit reduces the space needed for the equipment. The monitor is controlled by a separate control unit, such as an optional BKM-10R/11R Monitor Control Unit or by daisy chain connections. Auto chroma phase and white balance functions The chroma and phase of the decoder are automatically adjusted with the auto chroma phase function and the color temperature is automatically adjusted with the auto white balance function by using the BKM-14L Auto Setup Probe, etc. 4:3 area marker It is possible to check the 4:3 aspect area in the 16:9 picture by displaying the 4:3 marker. Expandable input capability You can obtain HD SDI signals, D1 SDI signals, NTSC/PAL signals or YPBPR/RGB signals by installing the optional input adaptors at the rear of the monitor. The input connector configuration can be easily modified and up to three adaptors can be installed. The BKM-129X Analog Component Input Adaptor is installed at SLOT 1 at the factory. Stable color temperature The beam current feedback circuit maintains a constant color temperature over long periods of time. Blue-only mode convenient for monitoring noise All three CRT cathodes can be driven with a blue signal, producing a monochrome display. This mode is convenient for chroma and phase adjustment, and for monitoring VTR noise. Controlling monitor groups Up to 32 monitors can be controlled from one control unit by the RS-485 serial remote connections. You can control individual monitors or monitor groups simply by entering monitor address or group numbers. You can also execute the same operation on all connected monitors, or put all connected monitors into the same setup and adjustment state. Other features • The monitor’s various functions and operating conditions can be set with on-screen menus. • Has both RS-485 serial remote and relay contact parallel remote control connectors. • H delay and V delay functions for simultaneous checking of the horizontal and vertical synchronization signals. VITS (Vertical Interval Test Signal) checking is also possible. • Auto and manual degaussing. • The monitor may be mounted in an EIA-standard 19inch rack, using an optional MB-520 (for 9-inch monitor) or BKM-30E14/31E14 (for 14-inch monitor) Rack Mount Kit. • The appearance of the monitor can be changed to 16:9 or 4:3 display by the replacement of a mask. • Operable by using a Sony lithium ion battery (BPL60/L90A) or DC 12 V external power source. (BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A only) • Built-in audio reproduce circuit and speaker. (BVMD9H5U/D9H5E/D9H5A only) Options 1) Trinitron® is a registered trademark of Sony Corporation. 2) 9-inch and 14-inch refer to the CRT size of the monitor. For effective picture size, see “Specifications” on page 47(E). 3) For details on the signal format, see “Available Signal Format” on page 53(E). 4 (E) MB-509 Mounting Panel Panel for the BVM-D9H5U/D9H5E/D9H5A to fill up the space created when mounting a video monitor to a rack with the MB-520 mounting bracket. BKM-30E14 Rack Mount Kit Rack mount kit for mounting the BVM-D14H5U/ D14H5E/D14H5A in an EIA standard 19-inch rack. BKM-31E14 Rack Mount Kit Rack mount kit for mounting the BVM-D14H1U/ D14H1E/D14H1A in an EIA standard 19-inch rack. Others VF-508 Monitor ENG Kit Kit that includes a light intercepting hood which is mounted on the front of a monitor, and a connector protector which is mounted on the rear. For external control Input adaptors BKM-10R Monitor Control Unit A controller for the BVM-D9H/D14H series video monitors, allowing you to control multiple monitors from one control unit. The input connector panel is configured by sliding the optional input adaptor into the input option slot at the rear of the monitor. Up to three adaptors can be installed to the monitor. The input signal type for each connector of the adaptor is set with the INPUT CONFIG menu, in accordance with the configuration of the connector panel. BKM-11R Monitor Control Unit A controller for the BVM-D9H/D14H and other BVM/ HDM series video monitors, allowing you to control multiple monitors from one control unit. BKM-14L Auto Setup Probe A probe, allowing the automatic adjustment of this monitor’s color temperature. For installation ........................................................................................................................................................................................................ MB-519 Mounting Panel Panel for the BVM-D9H1U/D9H1E/D9H1A to fill up the space created when mounting a video monitor to a rack with the MB-520 mounting bracket. Note When installing the adaptor, be sure to perform the necessary input signal setup with the INPUT CONFIG menu. If the setup is not performed, the adaptors may not function correctly. For information about the INPUT CONFIG menu, see “[C] Setting the Input Configuration — INPUT CONFIG Menu” on page 35(E). MB-520 Mounting Bracket Mounting bracket to mount one or two BVM-D9H1U/ D9H1E/D9H1A/D9H5U/D9H5E/D9H5A in a 19-inch EIA standard rack. 5 (E) Chapter 1 Overview Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Overview 1-5 1-6 Location and Function of Parts BKM-120D SDI 4:2:2 Input Adaptor Includes a decoder for serial digital component signals. D1 SDI input/output connectors for two serial digital channels and active loop-through output connectors. BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Front Panel BKM-127W NTSC/PAL Input Adaptor Includes decoders for analog composite NTSC and PAL signals. Input/output connectors for two analog channels and one YC channel. For the BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A, see pages 16(E) to 20(E). Chapter 1 Overview Chapter 1 Overview Overview BVM-D9H1U/D9H1E/D9H1A 8 Carrying handle 1 Tally lamp BKM-129X Analog Component Input Adaptor Includes input/output connectors for one analog channel and EXT SYNC input/output connectors. The BKM-129X is mounted to the monitor at the factory. BKM-142HD HD SDI Input Adaptor Includes a decoder for HD serial digital signals and input/output connectors for two serial digital signal channels and monitor output connector. Notes • The BKM-142HD uses two input option slots. • The signal from MONITOR OUT connector does not satisfy the ON-LINE signal specifications. 2 STANDBY lamp 9 OPTION connector 3 POWER lamp 0 VOLUME control 4 DEGAUSS button qa MANUAL adjustment knobs qs SHIFT button 5 POWER switch qd Function buttons 6 Ent button qf Menu operation buttons 7 Numeric keypad qg Stand BVM-D9H5U/D9H5E/D9H5A 8 Carrying handle BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1 Tally lamp 2 STANDBY lamp 9 OPTION connector 6 (E) 3 POWER lamp 7 (E) This manual explains the location and function of parts and controls of the BVM-D9H5U/D9H5E/D9H5A. The explanation also applies to the optional BKM10R/11R Monitor Control Unit. 1 Tally lamp With factory settings, the tally lamp lights as follows when the pins of the PARALLEL REMOTE [1] connector on the rear panel are shorted: – in red, when pins No.3 and No.9 are shorted. – in green, when pins No.4 and No.9 are shorted. – in amber, when pins No.3, No.4 and No.9 are shorted. The tally lamp lights as follows when the pins of the PARALLEL REMOTE [2] connector on the rear panel are shorted: – in red, when pins No.3 and No.5 are shorted. – in green, when pins No.4 and No.5 are shorted. – in amber, when pins No.3, No.4 and No.5 are shorted. By changing the setting in the REMOTE menu, different pins on the remote connector can be used to control the tally lamp. For information about the REMOTE menu, see “[D] Assigning the Remote Control Functions — REMOTE Menu” on page 37(E). 2 STANDBY lamp Lights when the monitor is in standby mode. The monitor will be in standby mode under the following conditions: • The AC adaptor or battery is attached to the monitor when the STANDBY MODE menu of the SYSTEM CONFIG menu is set to ON. • The monitor is changed from operation mode to standby mode by external control. For information about the SYSTEM CONFIG menu, see “[E] Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu” on page 39(E). 3 POWER lamp Lights when the monitor is put into operation mode from standby mode (see STANDBY lamp 2) by pressing the POWER switch 5. 8 (E) Note When the STANDBY lamp 2 is blinking, the monitor cannot be put into operation mode (internal data initialization is taking place). Wait until the STANDBY lamp 2 is steadily lit. 4 DEGAUSS button Press to degauss the CRT (every time the monitor is turned on, the CRT is degaussed automatically). To degauss again, wait for more than five minutes. 5 POWER switch Press to turn on/off the monitor. By setting with the ADDRESS menu, it is possible to turn on/off the power of the specified monitors only, or of all monitors at the same time. !¡ MANUAL adjustment knobs Each press of one of these knobs turns the knob’s green LED on or off. When the corresponding knob is on (lit), it is possible to manually adjust the contrast, brightness, chroma and phase by turning the corresponding knobs. The PHASE knob is also used to select the items or enter the setting values with the menus. It is possible to set the preset value for each adjusting item with the CONTROL PRESET ADJ menu. For Information about the CONTROL PRESET ADJ menu, see “ [A] Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ menu” on page 31(E). PHASE knob For information about the ADDRESS menu, see “Selecting the Monitor to Control — ADDRESS Menu” on page 45(E). CHROMA knob BRIGHT knob CONTRAST knob !£ Function buttons Change the operation conditions for the monitor. Each time the button is pressed, the LED turns on and turns off, and the operation conditions are changed. Each button has two functions. Select one of the two functions by pressing the SHIFT button !™. When the SHIFT button is set to ON, the LED lights in umber, and when the SHIFT button is set to OFF, the LED of each button lights in green. For the functions of the function buttons in case of SHIFT OFF and SHIFT ON, see pages 10(E) and 11(E). !¢ Menu operation buttons MENU button: Press to display the monitor menus. MENU UP 6 Ent button Use to confirm the items, values and characters entered. PHASE CHROMA BRIGHT CONTRAST 7 Numeric keypad Use to designate the channel number for the input signal to be monitored, or to enter the setting values with the menus. 1 2 3 Del 4 5 6 0 7 8 9 Ent 8 Carrying handle Pull out to use for carrying the monitor. 9 OPTION connector Used to connect the BKM-11R Monitor Control Unit or Auto Setup Probe (BKM-14L, etc.) 0 VOLUME control Adjusts the volume of the audio signals from the equipment connected to the AUDIO IN jacks at the rear of the monitor. DOWN For more information about menu operation, see “Basic Menu Operations” on page 25(E). Note Del button: Deletes the values and characters entered. Numeric buttons UP/DOWN buttons: Press to select the items and setting values. The PHASE and CHROMA knobs may not be adjusted due to the signals. However, these knobs are used for selecting the items or entering the setting values with the menus. !™ SHIFT button Press to select one of the two functions designated to the function buttons !£. Each time the SHIFT button is pressed, the LED turns on (SHIFT ON: lits in umber) and off (SHIFT OFF.) SHIFT OFF: The functions indicated above the function buttons can be used (the LED of the function button lits in green.) SHIFT ON: The functions indicated below the function buttons can be used (the LED of the function button lits in amber.) qg Stand Pull out to use. Using the Carrying Handle and Stand Pull up. Pull out toward front side. 9 (E) Chapter 1 Overview Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Location and Function of Parts 1-7 1-8 Location and Function of Parts Function buttons in SHIFT OFF mode (LEDs of function buttons in green) Function buttons in SHIFT ON mode (LEDs of function buttons in amber) 16:9 button: When this button is pushed in (ON), the aspect ratio changes to 16:9, and when set to OFF, the aspect ratio changes to 4:3. The aspect ratio is fixed to 16:9 when the signal other than 4:3 signal format is input. For details, see “Available Signal Format” on page 53(E). (H delay) button: When this button is pushed in (ON), the picture moves horizontally, and a horizontal sync signal appears approximately one quarter in the left edge of the screen. • The brightness of the picture increases automatically, and it makes it easy to check the sync part. button, a pulse cross • If it is pressed together with the picture is displayed. SYNC button: When this button is pushed in (ON), the monitor synchronizes to the sync signal input to the SYNC connectors on the BKM-129X (EXT SYNC). When set to OFF, it synchronizes to the sync signal included in the signals being monitored (INT SYNC). (V delay) button: When this button is pushed in (ON), the picture moves vertically, and a vertical sync signal appears approximately in the center of the screen. • The brightness of the picture increases automatically, and it makes it easy to check the sync part. • If it is pressed together with button, a pulse cross picture is displayed. Notes • When INT SYNC is selected, use a component including a sync signal on the Y signal, and use RGB signal including a sync signal on the G signal. • When the BKM-129X is not installed to the monitor or serial digital signals are monitored, INT SYNC is automatically selected. You cannot select EXT SYNC. MONO button: When this button is pushed in (ON), a monochrome picture is displayed. When the buttons is off, the monitor switches automatically color mode. Notes 16:9 SYNC B ONLY MONO APT COMB F1 F2 ADDRESS R G B F3 F4 MARKER B ONLY (blue only) button: When this button is pushed in (ON), red and green signals are cut, and only the blue signal is displayed as a monochrome picture. It makes it easy to adjust CHROMA and PHASE, and to check VTR noise. • The MONO button does not function with the RGB signal input. • When the NTSC or PAL color signals are received and color burst signals are not input, the monitor does not switch to color mode. R/G/B buttons: When these buttons are pushed in (ON), R(red), G(green), and B(blue) beams are cut respectively. ADDRESS button: When this button is pushed in (ON), the ADDRESS menu appears on the screen. By using the ADDRESS menu, operation conditions for multiple monitors are set. For more information about the ADDRESS menu, see “Selecting the Monitor to Control — ADDRESS Menu” on page 45(E). 16:9 F2 button: When this button is pushed in (ON), you can access directly the MANUAL menu of the level 1 of the COLOR TEMP ADJ menu, if the short-cut function is assigned to this button. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A F1 button: When this button is pushed in (ON), the characters disappear from the monitor on the MANUAL menu of the level 1 of the CONTROL PRESET ADJ menu, the MANUAL menu of the level 1 of the COLOR TEMP ADJ menu, and the ALIGNMENT menu. SYNC B ONLY MONO APT COMB F1 F2 ADDRESS R G B F3 F4 MARKER MARKER button: When this button is pushed in (ON), a 4:3 marker is displayed and it is possible to check the 4:3 aspect area in the 16:9 picture. Note The 4:3 marker is not displayed when the signals of the 4:3 aspect ratio are monitored or the monitor is in H/V delay mode F3/F4 buttons: For future expansion. COMB button: This button does not function with this monitor. However, when the BKM-127W NTSC/PAL Input Adaptor (optional) is installed and the NTSC or PAL color signals are received, the monitor can be used with the comb filter turned on. APT (aperture) button: When this button is pushed in (ON), the frequency response can be modified. The degree of modification is set with the menu. (When RGB signals are input, the button does not function.) 10 (E) 11 (E) Chapter 1 Overview Chapter 1 Overview (Underscan) button: When this button is pushed in (ON), the picture is underscanned by 3%, and four ends of the raster is displayed on the screen. BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Rear Panel For the BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A, see pages 21(E) to 23(E). BVM-D9H5U/D9H5E/D9H5A 1 PARALLEL REMOTE1/2 connectors (1: female, D-sub 9-pin, 2: modular connector) Form a parallel switch and controls the monitor externally. The pin assignment and factory setting function assigned to each pin are given below. 1: D-sub 9-pin 5 1 6 Input option slots 1 PARALLEL REMOTE 1/2 connectors 9 Pin number 2 DC 12V IN jack 7 Analog input/output connectors 3 EJECT button 4 AC adaptor/battery attachment place 5 SERIAL REMOTE connectors 8 AUDIO IN/OUT (input/output) jacks 6 Functions 1 Set input signal channel 1 (numeric keypad function) 2 Set input signal channel 2 (numeric keypad function) 3 Set red tally lamp on or off 4 Set green tally lamp on or off 5 Select sync signal (SYNC button function) 6 Set underscan on or off 7 8 Set a 16:9 aspect ratio on or off Set the 4:3 area marker display on or off 9 GND 2: modular connector 1 6 2 DC 12V IN jack (XLR-type, 4-pin) Connects the DC 12V external power source to use the monitor. 3 EJECT button While sliding this button, remove the AC adaptor or battery. 4 AC adaptor/battery attachment place Attach the AC adaptor or battery. 5 SERIAL REMOTE connectors (female, D-sub 9pin), and SERIAL REMOTE/CTRL UNIT select switch (BVM-D9H1U/D9H1E/D9H1A only) These are RS-485 serial interface connectors, used for connecting two or more BVM-xxE/F/G, BVM-xxD and HDM-xxE series monitors. The IN and OUT connectors form a loop-through connection. BVM-D9H1U/D9H1E/D9H1A only: The SERIAL REMOTE/CTRL UNIT select switch is set to SERIAL REMOTE at the factory. For connecting the monitor (used for daisy chain connections) Connect two monitors using a cable with D-sub 9pin plugs such as an RCC-5G (not supplied) as follows: Monitor 2 Monitor 1 Pin number BVM-D9H1U/D9H1E/D9H1A 6 Input option slots 1 PARALLEL REMOTE 1/2 connectors 2 DC 12V IN jack 7 Analog input/output connectors 3 EJECT button 1 Set input signal channel 1 (numeric keypad function) 2 Set input signal channel 2 (numeric keypad function) 3 Set red tally lamp on or off 4 Set green tally lamp on or off 5 GND 6 Set underscan on or off All pin function assignments can be changed with the REMOTE menu. For information about the REMOTE menu, see “ [D] Assigning the Remote Control Functions — REMOTE Menu” on page 37(E). 4 AC adaptor/battery attachment place 5 SERIAL REMOTE connectors and SERIAL REMOTE/CTRL UNIT select switch 12 (E) Functions To switch each function between on and off or between enable and disable, change pin connections in the following way. ON or enabled: Short each pin and pin 9 together for D-sub 9-pin. Short each pin and pin 5 together for modular connector. OFF or disabled: Leave each pin open. SERIAL REMOTE IN CTRL UNIT SERIAL REMOTE OUT SERIAL REMOTE IN CTRL UNIT SERIAL REMOTE OUT BVM-D9H1U/ D9H1E/D9H1A: Set to SERIAL REMOTE. BVM-D9H1U/ D9H1E/D9H1A: Set to SERIAL REMOTE. Cable with D-sub 9-pin plugs (not supplied) (continued) 13 (E) Chapter 1 Overview Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Location and Function of Parts 1-9 1-10 Location and Function of Parts 7 Analog input/output connectors (BKM-129X) ANALOG Attaching the AC adaptor or battery Connecting the AC power cord Attaching Attach the AC adaptor to the monitor, and then connect the supplied AC power cord. IN Y/G Chapter 1 Overview Chapter 1 Overview For connecting the BKM-10R Monitor Control Unit Connect the monitor and control unit using a cable with D-sub 9-pin plugs such as an RCC-5G (not supplied) as follows: Y/G connectors (BNC) OUT IN PB/B PB/B connectors (BNC) OUT SERIAL REMOTE IN CTRL UNIT IN PR/R PR/R connectors (BNC) AC plug holder (supplied) OUT Cable with D-sub 9-pin plugs (not supplied) BVM-D9H1U/D9H1E/D9H1A: Set to CTRL UNIT. AC power cord (supplied) IN SYNC SYNC connectors (BNC) OUT 129X Removing the AC adaptor or battery 6 Input option slots (three slots) The monitor may be fitted with optional input adaptors up to three. The BKM-129X is installed to the monitor at the factory. RGB signals or component signals (Y/PB/PR) can be fed in the IN connectors. The type of signal applied to each connector is set with the INPUT CONFIG menu. The OUT connectors are used for loop-through output of the input signal. 1 Attach the AC plug holder to the AC power cord, and connect it to the AC IN connector so that the cord does not come loose. 2 Notes • The BKM-142HD uses two input option slots. • Each adaptor can also be installed into SLOT 1. Install any adaptor to SLOT 1. For information about the INPUT CONFIG menu, see “ [C] Setting the Input Configuration — INPUT CONFIG Menu” on page 35(E). 8 AUDIO IN/OUT (input/output) jacks (BVMD9H5U/D9H5E/D9H5A only) Connects to the audio output jacks of the VCR or microphone amplifier. The monitor is equipped with three input and output jacks. You can obtain the loopthrough output from the OUT jacks. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 14 (E) Note Use the supplied AC adaptor for the BVM-D9H1U/ D9H1E/D9H1A/D9H5U/D9H5E/D9H5A models only. It is dangerous to use the AC adaptor for models other than these. 15 (E) BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Front Panel BVM-D14H5U/D14H5E/D14H5A 1 Tally lamp 2 POWER switch 0 SHIFT button 3 DEGAUSS button 4 Numeric keypad qa Function buttons 5 MANUAL adjustment buttons and knobs 6 Menu operation buttons qs OPTION connector 7 POWER lamp 8 STANDBY lamp 9 OVER LOAD lamp This manual explains the location and function of parts and controls of the BVM-D14H5U/D14H5E/D14H5A. The explanation also applies to the optional BKM10R/11R Monitor Control Unit. 1 Tally lamp With factory settings, the tally lamp lights as follows when the pins of the PARALLEL REMOTE [1] connector on the rear panel are shorted: – in red, when pins No.3 and No.9 are shorted. – in green, when pins No.4 and No.9 are shorted. – in amber, when pins No.3, No.4 and No.9 are shorted. The tally lamp lights as follows when the pins of the PARALLEL REMOTE [2] connector on the rear panel are shorted: – in red, when pins No.3 and No.5 are shorted. – in green, when pins No.4 and No.5 are shorted. – in amber, when pins No.3, No.4 and No.5 are shorted. By changing the setting in the REMOTE menu, different pins on the remote connector can be used to control the tally lamp. For information about the REMOTE menu, see “[D] Assigning the Remote Control Functions — REMOTE Menu” on page 37(E). BVM-D14H1U/D14H1E/D14H1A INPUT 1 2 4 5 6 7 8 9 Del 0 Ent 3 5 MANUAL adjustment buttons and knobs Each press of one of these buttons turns the button’s green LED on or off. When the corresponding button is on (lit), it is possible to manually adjust the contrast, brightness, chroma and phase by turning the corresponding knobs. The PHASE knob is also used to enter the setting values with the menus. It is possible to set the preset value for each adjusting item with the CONTROL PRESET ADJ menu. For Information about the CONTROL PRESET ADJ menu, see “ [A] Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ menu” on page 31(E). 2 POWER switch Press to turn on/off the monitor. By setting with the ADDRESS menu, it is possible to turn on/off the power of the specified monitors only, or of all monitors at the same time. BRIGHT button and knob CHROMA CHROMA button and knob 3 DEGAUSS button Press to degauss the CRT (every time the monitor is turned on, the CRT is degaussed automatically). To degauss again, wait for more than five minutes. 7 POWER lamp 8 STANDBY lamp 9 OVER LOAD lamp 16 (E) 4 Numeric keypad Use to designate the channel number for the input signal to be monitored, or to enter the setting values with the menus. CONTRAST button and knob BRIGHT For information about the ADDRESS menu, see “Selecting the Monitor to Control — ADDRESS Menu” on page 45(E). qs OPTION connector Ent button: Confirms the values and characters entered (ENTER button of the menu operation buttons 6 has the same function). Del button: Deletes the values and characters entered. CONTRAST MANUAL 1 Tally lamp Numeric buttons PHASE PHASE button and knob Note The PHASE and CHROMA knobs may not be adjusted due to the signals. However, these knobs are used for selecting the items or entering the setting values with the menus. (continued) 17 (E) Chapter 1 Overview Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Location and Function of Parts 1-11 1-12 Location and Function of Parts 6 Menu operation buttons MENU DOWN ENTER MENU button: Press to display the monitor menus. UP/DOWN buttons: Press to select the items and setting values. ENTER button: Press to confirm the items and values entered (Ent button on the numeric keypad 4 has the same function). For more information about menu operation, see “Basic Menu Operations” on page 25(E). 7 POWER lamp Lights when the monitor is put into operation mode from standby mode (see STANDBY lamp 8) by pressing the POWER switch 2. Note When the STANDBY lamp 8 is blinking, the monitor cannot be put into operation mode (internal data initialization is taking place). Wait until the STANDBY lamp 8 is steadily lit. 8 STANDBY lamp Lights when the monitor is in standby mode. The monitor will be in standby mode under the following conditions: • The MAIN POWER switch (on the rear panel) is turned on when the STANDBY MODE menu of the SYSTEM CONFIG menu is set to ON (the STANDBY lamp will blink for a few moments after the switch is turned on, then will light). • The monitor is changed from operation mode to standby mode by external control. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A For information about the SYSTEM CONFIG menu, see “[E] Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu” on page 39(E). Function buttons in SHIFT OFF mode (LEDs of function buttons in green) (Underscan) button: When this button is pushed in (ON), the picture is underscanned by 3%, and four ends of the raster is displayed on the screen. (H delay) button: When this button is pushed in (ON), the picture moves horizontally, and a horizontal sync signal appears approximately one quarter in the left edge of the screen. • The brightness of the picture increases automatically, and it makes it easy to check the sync part. button, a pulse cross picture is displayed. • If it is pressed together with the !¡ Function buttons Change the operation conditions for the monitor. Each time the button is pressed, the LED turns on and turns off, and the operation conditions are changed. Each button has two functions. Select one of the two functions by pressing the SHIFT button 0. When the SHIFT button is set to ON, the LED lights in umber, and when the SHIFT button is set to OFF, the LED of each button lights in green. For the functions of the function buttons in case of SHIFT OFF and SHIFT ON, see pages 19(E) and 20(E). !™ OPTION connector Used to connect the BKM-11R Monitor Control Unit or Auto Setup Probe (BKM-14L, etc.) 16 : 9 SYNC BLUE ONLY MONO R APT G COMB B F1 F3 F2 F4 ADDRESS MARKER (V delay) button: When this button is pushed in (ON), the picture moves vertically, and a vertical sync signal appears approximately in the center of the screen. • The brightness of the picture increases automatically, and it makes it easy to check the sync part. button, a pulse cross picture is displayed. • If it is pressed together with MONO button: When this button is pushed in (ON), a monochrome picture is displayed. When the buttons is off, the monitor switches automatically color mode. Notes • The MONO button does not function with the RGB signal input. • When the NTSC or PAL color signals are received and color burst signals are not input, the monitor does not switch to color mode. APT (aperture) button: When this button is pushed in (ON), the frequency response can be modified. The degree of modification is set with the menu. (When RGB signals are input, the button does not function.) COMB button: This button does not function with this monitor. However, when the BKM-127W NTSC/PAL Input Adaptor (optional) is installed and the NTSC or PAL color signals are received, the monitor can be used with the comb filter turned on. F1 button: When this button is pushed in (ON), the characters disappear from the monitor on the MANUAL menu of the level 1 of the CONTROL PRESET ADJ menu, the MANUAL menu of the level 1 of the COLOR TEMP ADJ menu, and the ALIGNMENT menu. F2 button: When this button is pushed in (ON), you can access directly the MANUAL menu of the level 1 of the COLOR TEMP ADJ menu, if the short-cut function is assigned to this button. ADDRESS button: When this button is pushed in (ON), the ADDRESS menu appears on the screen. By using the ADDRESS menu, operation conditions for multiple monitors are set. For more information about the ADDRESS menu, see “Selecting the Monitor to Control — ADDRESS Menu” on page 45(E). 9 OVER LOAD lamp Lights when some malfunction has occured. When the OVER LOAD lamp is lit, consult your nearest Sony service facilities. 18 (E) 19 (E) Chapter 1 Overview Chapter 1 Overview UP 0 SHIFT button Press to select one of the two functions designated to the function buttons !¡. Each time the SHIFT button is pressed, the LED turns on (SHIFT ON: lits in umber) and off (SHIFT OFF.) SHIFT OFF: The functions indicated above the function buttons can be used (the LED of the function button lits in green.) SHIFT ON: The functions indicated below the function buttons can be used (the LED of the function button lits in amber.) Function buttons in SHIFT ON mode (LEDs of function buttons in amber) 16:9 button: When this button is pushed in (ON), the aspect ratio changes to 16:9, and when set to OFF, the aspect ratio changes to 4:3. BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Rear Panel BVM-D14H5U/D14H5E/D14H5A Chapter 1 Overview Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Location and Function of Parts The aspect ratio is fixed to 16:9 when the signal other than 4:3 signal format is input. For details, see “Available Signal Format” on page 53(E). 3 Input option slots SYNC button: When this button is pushed in (ON), the monitor synchronizes to the sync signal input to the SYNC connectors on the BKM-129X (EXT SYNC). When set to OFF, it synchronizes to the sync signal included in the signals being monitored (INT SYNC). Notes 16 : 9 • When INT SYNC is selected, use a component including a sync signal on the Y signal, and use RGB signal including a sync signal on the G signal. • When the BKM-129X is not installed to the monitor or serial digital signals are monitored, INT SYNC is automatically selected. You cannot select EXT SYNC. 1 PARALLEL REMOTE 1/2 connectors 4 Analog input/output connectors 2 SERIAL REMOTE connectors 5 MAIN POWER switch 6 AC IN connector SYNC BLUE ONLY MONO R APT G COMB B F1 F3 F2 F4 BLUE ONLY button: When this button is pushed in (ON), red and green signals are cut, and only the blue signal is displayed as a monochrome picture. It makes it easy to adjust CHROMA and PHASE, and to check VTR noise. R/G/B buttons: When these buttons are pushed in (ON), R(red), G(green), and B(blue) beams are cut respectively. BVM-D14H1U/D14H1E/D14H1A 3 Input option slots ADDRESS MARKER F3/F4 buttons: For future expansion. 1 PARALLEL REMOTE 1/2 connectors MARKER button: When this button is pushed in (ON), a 4:3 marker is displayed and it is possible to check the 4:3 aspect area in the 16:9 picture. 4 Analog input/output connectors Note 2 SERIAL REMOTE connectors The 4:3 marker is not displayed when the signals of the 4:3 aspect ratio are monitored or the monitor is in H/V delay mode 5 MAIN POWER switch 6 AC IN connector 7 CONTROL UNIT connector (continued) 20 (E) 21 (E) 1-13 1-14 Location and Function of Parts 1: D-sub 9-pin 5 9 Pin number 1 6 Functions 1 Set input signal channel 1 (numeric keypad function) 2 Set input signal channel 2 (numeric keypad function) 3 Set red tally lamp on or off 4 Set green tally lamp on or off 5 Select sync signal (SYNC button function) 6 Set underscan on or off 7 8 Set a 16:9 aspect ratio on or off Set the 4:3 area marker display on or off 9 GND To switch each function between on and off or between enable and disable, change pin connections in the following way. ON or enabled: Short each pin and pin 9 together for D-sub 9-pin. Short each pin and pin 5 together for modular connector. OFF or disabled: Leave each pin open. 4 Analog input/output connectors (BKM-129X) 6 AC IN connector (3-pin) Connects the monitor to an AC power source, via the supplied AC power cord. Chapter 1 Overview Chapter 1 Overview 1 PARALLEL REMOTE1/2 connectors (1: female, D-sub 9-pin, 2: modular connector) Form a parallel switch and controls the monitor externally. The pin assignment and factory setting function assigned to each pin are given below. 2 SERIAL REMOTE connectors (female, D-sub 9-pin) These are RS-485 serial interface connectors, used for connecting two or more BVM-xxE/F/G, BVM-xxD and HDM-xxE series monitors. The IN and OUT connectors form a loop-through connection. Connect two monitors using a cable with D-sub 9-pin plugs such as an RCC-5G (not supplied) as shown in the figure on the next page. Monitor 1 SERIAL REMOTE Monitor 2 SERIAL REMOTE 7 CONTROL UNIT connector (female, D-sub 9pin) (BVM-D14H1U/D14H1E/D14H1A only) Connects a monitor control unit such as the BKM-10R using a cable with D-sub 9-pin plugs such as an RCC5G (not supplied). 2: modular connector 1 Pin number 6 IN OUT OUT Functions BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1 Set input signal channel 1 (numeric keypad function) 2 Set input signal channel 2 (numeric keypad function) 3 Set red tally lamp on or off 4 Set green tally lamp on or off 5 GND 6 Set underscan on or off All pin function assignments can be changed with the REMOTE menu. For information about the REMOTE menu, see “ [D] Assigning the Remote Control Functions — REMOTE Menu” on page 37(E). 22 (E) IN Cable with D-sub 9-pin plugs (not supplied) 3 Input option slots (three slots) The monitor may be fitted with optional input adaptors up to three. The BKM-129X is installed to the monitor at the factory. Notes • The BKM-142HD uses two input option slots. • Each adaptor can also be installed into SLOT 1. Install any adaptor to SLOT 1. 23 (E) BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A Basic Menu Operations BVM-D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A Installing the 4:3 mask 1 Remove the 16:9 mask. Installing the 4:3 mask 1 Menu Operation Buttons The menus are operated using the menu operation buttons on the front panel of the monitor or BKM10R/11R Monitor Control Unit. Buttons on the BVM-D9H5U/D9H5E/D9H5A Buttons on the BVM-D14H5U/D14H5E/D14H5A INPUT PHASE knob MENU button Numeric keypad Remove four screws from both sides of the monitor and then remove the16:9 mask. 2 Install the 4:3 mask (supplied) and fix both sides with four screws. MENU 1 2 3 Del UP 4 5 6 0 DOWN 7 8 9 Ent DOWN button UP button 1 2 3 4 5 6 7 8 9 Del 0 Ent Numeric keypad Del button PHASE 2 Chapter 2 MenuChapter 2 Menu When the aspect ratio is switched from 16:9 to 4:3, replace the 16:9 mask with the supplied 4:3 mask. Chapter 1 Overview BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Installation of the 4:3 Mask Ent button Del button PHASE PHASE knob Ent button MENU button Install the 4:3 mask (supplied). 1 Attach the lower portion of the mask. 2 Attach the upper portion of the mask by pressing it until the click. UP MENU DOWN ENTER UP/DOWN buttons ENTER button Replacing the 16:9 mask The functions of the menu operation buttons are described below. Remove the 4:3 mask and replace the 16:9 mask using the same procedures as those for installing the 4:3 mask. Button UP button DOWN button MENU button Replacing the 16:9 mask ENTER button/ Ent button Executes the items selected and settings. PHASE knob By turning this knob clockwise, the cursor moves upward. In setting mode, increases the setting and adjustment values (has the same function as UP button). By turning this knob counterclockwise, the cursor moves downward. In setting mode, decreases the setting and adjustment values (has the same function as DOWN button). Numeric keypad Enters the numerical values. Del button Deletes the values and characters entered. Remove the 4:3 mask and replace the 16:9 mask using the same procedures as those for installing the 4:3 mask. 24 (E) Function Moves the cursor upward. In setting mode, increases the setting and adjustment values. Moves the cursor downward. In setting mode, decreases the setting and adjustment values. Displays the Menus. Goes back to the menu of the upper level (on the Main Menu, goes back to the normal picture). 25 (E) 1-15 1-16 Basic Menu Operations Follow the steps described below to display the menu and perform the adjustment or setup you wish. M E N U P R E SE T T E M P I N P U T C O N F I G... A D J ... A D J ... R E M O T E ... S Y S T E M C O N F I G ... S T A T U S ... A L I G N M E N T ... BA BB BC BD BE BF BG Press the MENU button. The Menu List is displayed. 2 Using the UP/DOWN buttons or PHASE knob, move the cursor to the desired item. (Example: select the INPUT CONFIG menu by pressing the DOWN button.) I N P U T C H M E N U C O N T R O L C O L O R Menu List pI R S S When you select one item on the main menu, the level 1 menu corresponding to the selected item on the main menu appears. N P U T P R E SE T T E M P A D J ... A D J ... C O N F I G... A L I G N M E N T ... Cursor Menu List Press the ENTER button or Ent button. The Level 1 of the selected menu is displayed. I N P U T About menu numbers For purposes of explanation in this manual, each menu is preceded by menu numbers. The alphabet determines the classification of menus on the Menu List (Main Menu), and the numbers determine the level and the order. These menu numbers are not shown on the screen. C H C O N F I G( 1 / 2 ) ↓ N X U O P U T N O T S Y N C S L OT D I O I N P U T L O R T E M P A P E R T U R E V A LU E C H A N N E L N A M E... N X U O P U T N O T S Y N C S L OT D I O I N P U T L O R T E M P S L O T 1 1 S L O T 1 - - S T D 1 0 0 P R O G 1 I N P U T Selects from various options. C H C O N F I G( 1 / 2 ) Indicates that this item has sub-list. Thus, you can go to the lower level. To abort menu operation Press the MENU button. The menu of the upper level is displayed. The setting or adjustment being performed is canceled, and data loading or saving is aborted. If “NG” or “ERROR” appears during menu operation Press the MENU button to return to the menu in use. ↓ 1 F O R M A T ... S L O T I N P U pE X T A U D I C O L O Y P B P R N O T N O S Y N C O R S L O T 1 S L OT I N P U T T E M P 1 S L O T 1 - - S T D A P E R T U R E V A LU E C H A N N E L N A M E... - - P R O G 2 Using the UP/DOWN buttons or PHASE knob, change the setting. 3 Press the ENTER or Ent button. The setting is confirmed (The item is displayed in white text again). Y P B P R 1 S L O T 1 1 S L O T 1 - - S T D Using the UP/DOWN buttons or PHASE knob, move the cursor to the desired item in the setting list. C H A N N E L C H N A M E 1 pP R O G E D I T - - P R O G BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A C A M V T R Indicates the CONTROL PRESET ADJ menu Indicates the first menu in Level 1 Using the UP/DOWN buttons or PHASE knob, move the cursor to the desired item and press the ENTER or Ent button. The selected item is displayed in yellow text and set to setting mode. Selecting from the setting list 1 p F O R M A T ... S L O T N O I E A C ↓ 3 ↓ Y P B P R Selecting in setting mode Enters numerical values. E M O T E ... Y S T E M C O N F I G ... T A T U S ... Note I E A C A P E R T U R E V A LU E C H A N N E L N A M E... For information about the items on the main menu, see “Menu Structure” on page 30(E). Menu settings that cannot be changed are displayed in blue. C O N F I G( 1 / 2 ) 1 p F O R M A T ... S L O T N O the menu continues onto next page. [ ↑ ] indicates that the menu is continued from previous page. Choosing one of two or more selections N E W (continued) N A M E Indicates the third menu in Level 2 Indicates the fifth menu in Level 3 e.g. A 1 3 5 Note Only the menus which require explanation are preceded by menu numbers. Thus, the menu number is counted without menus which do not require explanation. 26 (E) 2 Press the ENTER or Ent button. The display returns to the menu of the upper level, and the selected setting is executed. 27 (E) Chapter 2 Menu Chapter 2 Menu C O L O R 1 Repeat steps 2 and 3 until the desired menu is displayed. For more information about setting and adjustments, see below. [ ↓ ] indicates that ↓ Press the MENU button. The menu list is displayed on the screen. pC O N T R O L 4 Menu Operation ↓ Displaying the Menus 2 Entering a numerical value Using the UP/DOWN buttons or PHASE knob, move the cursor to the desired item and press the ENTER or Ent button. The selected item is displayed in yellow text and set to setting mode. C H C O N F I G( 1 / 2 ) E D I T C A M V T R 1 Y P B P R S L O T S L O T 1 N O N O pN E W ? pA P E R T U R E V A L U E C H A N N E L N A M E... S L O T 1 - - S T D 1 0 0 P R O G 3 Set the value in one of the following three ways: • Enter the value directly using the numeric keypad and press the ENTER or Ent button • Select the value using the UP/DOWN buttons • Select the value using the PHASE knob Select the character you wish to enter using the UP/DOWN buttons or PHASE knob. When you press the UP button, or turn the PHASE knob clockwise, the characters and symbols appear in the order shown below. 4 Press the ENTER or Ent button. The selected character is entered. C H A N N E L C H Display the setting menu and set the cursor to NEW NAME using the UP/DOWN buttons or PHASE knob. C H For information about the ADDRESS menu, see “Selecting the Monitor to Control —ADDRESS Menu” on page 45(E). If you press the UP/DOWN button or turn the PHASE knob counterclockwise, the characters and symbols appear in the reverse order described above. Press the ENTER or Ent button. The setting is confirmed (The item is displayed in white text again). C H A N N E L In addition to the menus displayed on the menu list, the ADDRESS menu is provided. This ADDRESS menu is used to select the monitor or the monitor group, so that when several monitors are connected together via serial remote ports, the control panel can select which monitor to control. To display or exit the ADDRESS menu, press the ADDRESS button. The method of choosing menu items and changing settings is the same as with the other menus. A B .............Y Z 0 1 ...............8 9 ( , ) : ; . - + / & (space) ? Entering characters 1 N A M E 1 E X T S Y N C S L OT A U D I O I N P U T C O L O R T E M P 3 N A M E P R O G ↓ F O R M A T ... I N P U T 2 C H A N N E L 1 ADDRESS Menu Chapter 2 Menu I N P U T Press the ENTER or Ent button. “?” is displayed in yellow. The “?” indicates the position where character input is possible. C H ↓ 1 Chapter 2 Menu BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Basic Menu Operations N A M E 1 P R O G E D I T C A M V T R N A M E 1 pN E W C ? P R O G N A M E E D I T C A M V T R pN E W N A M E 5 Repeat steps 3 and 4 until all the characters are entered, then press the ENTER or Ent button. The selected characters are confirmed, and the display returns to the menu of the previous level. To correct the entered character Press the Del button on the numeric keypad. The character on the left side of the “?”(in yellow) is deleted. 28 (E) 29 (E) 1-17 1-18 A Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ Menu Menu Structure Menus consist of one to three levels. Overview Detailed information on the levels of menus is described at the top of explanation of each menu. Main Menu Functions CONTROL PRESET ADJ menu Sets the preset values for the input signal’s chroma, contrast, phase, and brightness. (page 31(E)) B COLOR TEMP ADJ menu Sets the color temperature. (page 33(E)) C INPUT CONFIG menu Sets the input channel. (page 35(E)) D REMOTE menu Sets the remote control functionality. (page 37(E)) E SYSTEM CONFIG menu Sets the power-up conditions and data about the screen display. (page 39(E)) F STATUS menu Displays the information about the monitor or options installed in the monitor. (page 42(E)) G ALIGNMENT menu Adjusts the position, size and geometry of the picture. (page 43(E)) Preset values can be set in the following two ways: • Adjustment with the MANUAL adjustment knobs (MANUAL menu) • Automatic adjustment (AUTO menu) An external color bar signal is necessary. Note After installing the optional board, carry out AUTO adjustment. Structure of the CONTROL PRESET ADJ Menu Level 1 Level 2 MANUAL A1 CHROMA PHASE CONTRAST BRIGHT AUTO A2 FULL FIELD WHITE 100% 8COLOR BAR 100% 8COLOR BAR 75% SMPTE COLOR BAR EIA COLOR BAR Setting Lists in the CONTROL PRESET ADJ Menu This section explains the setting lists displayed in the menu. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. For more information about the menu number, see “About menu numbers” on page 26(E). 30 (E) 31 (E) Chapter 2 Menu Chapter 2 Menu A The preliminary adjustments of chroma, phase, contrast and brightness are carried out with the CONTROL PRESET ADJ menu to set the preset values to the knobs for the above-mentioned adjustments. [A] CONTROL PRESET ADJ menu Select the setting method. MANUAL... : Set with the MANUAL adjustment knobs. ÷[A1] AUTO... : Set by automatic adjustment. ÷[A2] [A1] MANUAL menu Adjust values by turning the CHROMA, PHASE, CONTRAST, and/or BRIGHT knobs. After the adjustment, press the ENTER or Ent button to confirm the adjusted values. The setting value is 0 to 200. CHROMA: xxx PHASE: xxx CONTRAST: xxx BRIGHT: xxx When you want to erase characters from the screen while adjusting manually Press the [F1] button. The characters disappear. To display characters, press the [F1] button again. To reset the setting to the default Press the corresponding MANUAL adjustment button (BVM-D14H5U/D14H5E/D14H5A) or knob (BVMD9H5U/D9H5E/D9H5A.) The adjusted value is reset to 100 (default). [A2] AUTO menu You can adjust the CHROMA and PHASE levels automatically. Input the color bar signals to the board to be adjusted and select the required color bar signals. ÷Adjustment is carried out. 8COLOR BAR 100%: 100% full-field 8-color bar (white, yellow, cyan, green. magenta, red, blue, black) 8COLOR BAR 75%: 75% full-field color bar (with 100% white signal) SMPTE COLOR BAR: SMPTE standard color bar EIA COLOR BAR: EIA standard color bar B Adjusting the Color Temperature — COLOR TEMP ADJ Menu Overview The monitor can memorize the data for up to three color temperatures (STD, COL1, COL2.) The data for each color temperature is adjusted with the COLOR TEMP ADJ menu. The data of the color temperature selected in the INPUT CONFIG menu is adjusted. Color temperature adjustment can be made in the following three ways: Notes • The CRT size of the BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A is small. So, when a probe other than the Sony BKM-14L is used, use the probe closely to the CRT screen. • After the color temperature is adjusted by automatic adjustment, carry out the AUTO adjustment of the CONTROL PRESET ADJ menu (AUTO CHROMA PHASE adjustment.) • Knob adjustment (MANUAL menu) You can adjust the color temperature with the bias and gain knobs. • Automatic adjustment using a probe (PROBE menu) You can use the following probes for automatic adjustment of color temperature. Except for the Sony BKM-14L, a cable is required to connect the color analyzer to the monitor. Manufacturer Probe Model Name SONY BKM-14L (no cable required) GRASEBY SLS 9400 MINOLTA CA-100 PHILIPS PM 5639 THOMA TF6 • Copying other color temperature data (COPY menu) You can copy the memorized color temperature data (STD/COL1/COL2/D65/D93.) Use the factory setting value or the adjusted value as an original value to shorten the adjustment time. Structure of the COLOR TEMP ADJ Menu Level 1 Level 2 MANUAL B1 ADJUST PROBE B2 START PROBE X Y LOW LIGHT (20 IRE) HIGH LIGHT (100 IRE) LOAD REF VALUE B21 Note When you execute the AUTO menu, SYNC button should be set to OFF (INT SYNC). EXT SYNC will cause an error abortion of auto adjustment procedure. @ @ @ COPY B3 32 (E) For more information about the cable specification required and about the connection, see “Connection Cable Specifications for Color Temperature Probes” on page 54(E). Level 3 D65 D93 STD COL1 COL2 D65 D93 33 (E) Chapter 2 Menu Chapter 2 Menu BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A Preset Adjustment of the Picture Level Control Knobs — CONTROL PRESET ADJ Menu 1-19 1-20 C Setting the Input Configuration B Adjusting the Color Temperature — COLOR TEMP ADJ Menu Setting Lists in the COLOR TEMP ADJ Menu This section explains the setting lists displayed in the menu. For more information about the menu number, see “About menu numbers” on page 26(E). • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. [B] COLOR TEMP ADJ menu Select the adjustment method. MANUAL... : Set with the MANUAL adjustment knob. ÷[B1] PROBE... : Set using a probe. ÷[B2] COPY... : Copy data from elsewhere. ÷[B3] BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A [B1] MANUAL menu Adjust the gain and bias with the MANUAL adjustment knob. ADJUST... : Adjust the gain and bias. To shift between gain adjustment and bias adjustment, press UP/DOWN buttons. Use appropriate knobs in each adjustment as described below. After the adjustment, press the ENTER or Ent button to confirm the adjusted values. RED: CONTRAST KNOB (Adjust the R gain or bias with the CONTRAST knob.) GREEN: BRIGHT KNOB (Adjust the G gain or bias with the BRIGHT knob.) BLUE: CHROMA KNOB (Adjust the B gain or bias with the CHROMA knob.) LUMINANCE: PHASE KNOB (Adjust luminance with the PHASE knob.) To reset RED/GREEN/BLUE to the value before adjustment When you are adjusting the gain or bias using the MANUAL adjustment knobs, you can reset the setting to the one before adjustment by pressing the corresponding MANUAL adjustment button (BVM-D14H5U/D14H5E/D14H5A) or knob (BVM-D9H5U/D9H5E/D9H5A). To reset all of settings at the same time, press the PHASE button or knob. 34 (E) To access the MANUAL menu directly When the [F2] button is assigned as the short-cut key to the MANUAL menu, you can directly access the MANUAL menu that corresponds to the color temperature setting (STD/COL1/COL2) set to the image on the screen. For details of how to assign the short-cut key, see “ [E] Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu” on page 39(E). [B2] PROBE menu Select the probe for color temperature adjustment. START: Start adjustment. PROBE: Select the probe. X: Enter the x coordinate. Y: Enter the y coordinate. LOW LIGHT (20IRE): Enter the luminance (cd/m2) for low light. HIGH LIGHT (100IRE): Enter the luminance (cd/ m2) for high light. LOAD REF VALUE: Select the standard settings of the x and y coordinates. ÷[B21] [B21] LOAD REF VALUE Select one of the followings: D65: Use D65 setting (x and y coordinates and standard luminance). D93: Use D93 setting (x and y coordinates and standard luminance). [B3] COPY menu Select one of followings: ÷ The current data, which is used for adjusting, is copied. STD: Copy STD data (factory setting: D65). COL1: Copy COL 1 data (factory setting: D93). COL2: Copy COL 2 data (factory setting: D65). D65: Copy the color temperature of D65. D93: Copy the color temperature of D93. Note The current data which is used for adjusting (selected in the INPUT CONFIG menu) is displayed in blue letters and you can not select it. Overview You can set up to nine input channels. Data pertaining to the input signals are set with the INPUT CONFIG menu. When a channel number (1 to 9) is entered with the numeric keypad, it is then possible to set which input connector on the rear panel will be assigned to that channel number, and select the type of signal that will be connected. Assigning slot and connector numbers Set which input connector on which slot will be assigned to the current channel. To assign D1 serial digital signals Serial digital signals can be assigned to the slot where the BKM-120D is installed. To assign analog composite signals Analog composite signals can be assigned to the slot where the BKM-127W is installed. To assign HD serial digital signals HD serial digital signals can be assigned to the slots where the BKM-142HD is installed. To assign analog component or RGB signals Analog component or RGB signals can be assigned to the slot where BKM-129X is installed. Assigning the signal type and format The signal type and format which can be assigned to each channel number vary, depending on what adaptors are installed in the rear panel. Structure of the INPUT CONFIG Menu Level 1 INPUT CONFIG (1/2) CH x FORMAT C1 SLOT NO INPUT NO EXT SYNC SLOT AUDIO INPUT COLOR TEMP APERTURE VALUE CHANNEL NAME C 2 Level 2 YPBPR RGB NTSC, PAL D1-SDI HD-SDI PROG EDIT CAM VTR NEW NAME INPUT CONFIG (2/2) CH x 1125/60I SYSTEM H PHASE MARKER PHASE MARKER WIDTH NTSC SET UP YPBPR MATRIX VCR MODE 35 (E) Chapter 2 Menu Chapter 2 Menu How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. Note You cannot reset the setting after you press the ENTER or Ent button. — INPUT CONFIG Menu Setting Lists in the INPUT CONFIG Menu This section explains the setting lists displayed in the menu. How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. For more information about the menu number, see “About menu numbers” on page 26(E). • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. [C] (1/2) INPUT CONFIG (1/2) menu Set input signal data for each channel. CH x: Current channel is indicated. To change the channel, enter a channel number with the numeric keypad. The settings below will be stored as information of this channel. FORMAT... : Select the input signal type. ÷[C1] SLOT NO: Select the slot number. INPUT NO: Select the input connector number. EXT SYNC SLOT: Select the slot when the external sync signal is used. AUDIO INPUT (BVM-D9H5U/D9H5E/D9H5A only): Select the audio input number. COLOR TEMP: Select the color temperature. APERTURE VALUE: Enter the aperture adjustment value (0 to 200). CHANNEL NAME: Give the channel a name. ÷[C2] [C] (2/2) INPUT CONFIG (2/2) menu Set input signal data for each channel. CH x: Current channel is indicated. To change the channel, enter a channel number with the numeric keypad. The settings below will be stored as information of this channel. 1125/60I SYSTEM: Select the number of active scanning lines per frame for 1125/60I input signals. When the HD SDI signal is input, the number of active scanning lines is selected automatically. 1035: The active scanning lines are 1035 lines. 1080: The active scanning lines are 1080 lines 36 (E) — REMOTE Menu Overview H PHASE: Set the horizontal picture position (–128 to +127). MARKER PHASE: Set the 4:3 marker position. MARKER WIDTH: Set the 4:3 marker width. NTSC SET UP: Set the setup level when the BKM127W is installed. SETUP 7.5 or 0. YPBPR MATRIX: Select the matrix when YPBPR signals of the signal format 480/60I or 480/60P (TV lines 525) are input. VCR MODE: Compensate for a distorted picture when the input signals from the VCR are not typical. This mode is effective when the signal formats 480/60I or 575/50I are input. ON: Operates when the signal formats 480/60I or 575/50I are input. OFF: Does not operate. The remote control functions are set with the REMOTE menu. With this monitor, both serial remote control (SERIAL REMOTE) and parallel remote control (PARALLEL REMOTE) are possible. • Settings for the serial remote control (SERIAL REMOTE) An address number (MONITOR ADDRESS) and group number (GROUP ADDRESS) can be assigned to the monitor connected to the SERIAL REMOTE connector. • ON/OFF setting for the parallel remote control (PARALLEL REMOTE) • Settings for the parallel remote control (PARALLEL REMOTE) Functions can be assigned to the pins of the PARALLEL REMOTE connector. [C1] FORMAT menu Select the signal format. YPBPR: Select the component signals when the BKM-129X is installed. SPMTE, BETACAM 7.5 or 0. RGB: Select when the BKM-129X is installed. NTSC, PAL: Selects when the BKM-127W is installed. D1-SDI: Select when the BKM-120D is installed. HD-SDI: Select when the BKM-142D is installed. Priority order of the remote control functions It is possible to simultaneously use the BKM-10R/11R Monitor Control Unit, SERIAL REMOTE, and PARALLEL REMOTE for control, but commands from PARALLEL REMOTE have priority. Therefore, it is impossible for the BKM-10R/11R or SERIAL REMOTE to change items set by PARALLEL REMOTE. There is no priority order between commands from SERIAL REMOTE and the BKM-10R/11R control panel. [C2] CHANNEL NAME menu Give the channel a name. Enter a name after a preset one or a new one. PROG: Program signal. EDIT: Signal from an editor. CAM: Camera signal. VTR: Signal from a VTR. NEW NAME: Enter a new name. (Up to 20 characters can be entered and up to six characters from the head of the name are displayed in the INPUT CONFIG menu ([C] 1/2).) PARALLEL REMOTE 1 and 2 are connected parallel inside the unit, therefore, there is no priority order between them. About monitor address and group numbers It is possible to control up to 32 monitors connected via serial remote connector (using the SERIAL REMOTE connector). By giving each monitor a monitor address and group number, it is possible to control just a specific monitor or monitor group. With the SERIAL REMOTE menu, each monitor can be set with a monitor address and group number, between 1 and 99. The ADDRESS menu is used to control the monitors which are connected by the serial remote connectors. For information about the ADDRESS menu, see “Selecting the Monitor to Control — ADDRESS Menu” on page 45(E). Note The address number must differ from one monitor to another. If two or more monitors have the same address number, an operation error occurs. Structure of the REMOTE Menu Level 1 SERIAL REMOTE D1 MONITOR ADDRESS GROUP ADDRESS PARALLEL REMOTE PARALLEL REMOTE CONFIG D2 Level 2 1 PIN D21 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN Level 3 CH D211 (1/2) R OFF D211 (2/2) 37 (E) Chapter 2 Menu Chapter 2 Menu BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A D Assigning the Remote Control Functions C Setting the Input Configuration — INPUT CONFIG Menu 1-21 1-22 E Setting the Power-Up Conditions and Data about D Assigning the Remote Control Functions — REMOTE Menu Setting Lists of the REMOTE Menu This section explains the setting lists displayed in the menu. For more information about the menu number, see “About menu numbers” on page 26(E). • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. [D] REMOTE menu Select the type of remote control. SERIAL REMOTE : Set the address and group number of the monitor controlled via the SERIAL REMOTE connector. ÷[D1] PARALLEL REMOTE: Select whether parallel remote control will be used or not (ON or OFF.) PARALLEL REMOTE CONFIG : Set the pin assignments for the PARALLEL REMOTE connector. ÷[D2] [D1] SERIAL REMOTE menu Set the monitor address and group number. MONITOR ADDRESS: Enter a number. GROUP ADDRESS: Enter a number. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A [D2] PARALLEL REMOTE CONFIG menu Select the PARALLEL REMOTE connector pins for which you want to change the function. The factory settings for each pin are given below. ÷[D211] PINs 1 to 4, and PIN 6 of the PARALLEL REMOTE 1 and 2 are common settings. 1 PIN: CH01 2 PIN: CH02 3 PIN: TALLY RED 4 PIN: TALLY GREEN 5 PIN: EXT SYNC (PARALLEL REMOTE [1]) GND (PARALLEL REMOTE [2]) 6 PIN: UNDERSCAN 7 PIN: 16:9 8 PIN: 4:3 MARKER 38 (E) Overview Note PINs 1 to 4, and PIN 6 of the PARALLEL REMOTE 1 and 2 are connected inside the unit, therefore different functions cannot be assigned to those pins. [D211] (1/2) 1-8 PIN menu (1/2) Assign a function to the selected pin. CH: Select a channel number. Enter the desired channel number with the numeric keypad. ----: Set to unused. UNDER SCAN: Set underscan on or off. 16:9: Set a 16:9 aspect ratio on or off. H DELAY: Set the horizontal sync display on or off. V DELAY: Set the vertical sync display on or off. EXT SYNC: Set the synchronization to external sync signals enabled or disabled. APERTURE: Set the correction of frequency characteristics enabled or disabled. MONO: Set monochrome display on or off. BLUE ONLY: Set the blue signal pictures display (monochrome) on or off. [D211] (2/2) 1-8 PIN menu (2/2) Assign a function to the selected pin. R OFF: Set cutting red beams enabled or disabled. G OFF: Set cutting green beams enabled or disabled. B OFF: Set cutting blue beams enabled or disabled. 4:3 MARKER: Set the 4:3 marker display on or off. CAPTION VISION: Set Caption Vision on or off. TALLY RED: Set tally red on or off. TALLY GREEN: Set tally green on or off. DEGAUSS: Set degaussing on or off. POWER OFF: Set the monitor power on or off. For the pin assignment, see “PARALLEL REMOTE 1/2 connectors” in the Location and Function of Parts on page 13(E) for BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A or page 22(E) for BVM-D14H1U/D14H1E/ D14H1A/D14H5U/D14H5E/D14H5A. The SYSTEM CONFIG menu is displayed on the two pages. The SYSTEM CONFIG (1/2) menu is used for the following settings: • Power-up condition (STANDBY MODE menu) This menu sets the condition of the monitor when the MAIN POWER switch on the rear panel is switched on (BVM-D14H1U/D14H1E/D14H1A/D14H5U/ D14H5E/D14H5A) or when the battery is installed (BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A.) • Power-up input channel (DEFAULT CH menu) This menu sets the power-up input channel. • Time from power-up until degauss (DEGAUSS DELAY menu) If several monitors are turned on at the same time and all start degaussing at the same time, there will be a very large current draw on the power supply for a few moments. To prevent this, the delay time between power-up and degaussing can be set for each monitor independently. • Setting of the contrast and brightness after adjusting the white balance (CONT/BRT HOLD menu) Selects if the adjusted contrast and brightness are retained or they are reset to the center values, when the color temperature is adjusted in the COLOR TEMP ADJ menu. • Assigning shortcut to the COLOR TEMP ADJ menu to the [F2] key (COL TEMP SHORT-CUT menu) Assigns the shortcut to the MANUAL menu of the COLOR TEMP ADJ menu to the [F2] key. This allows you to jump directly to the MANUAL menu corresponding to the color temperature set to the currently displayed image (STD/COL 1/COL 2.) • Auto color control (ACC SW menu) (when using the BKM-127W) Selects if the ACC (Auto Color Control) circuit is turned on or off. • Selecting the monitor to copy the original data (CONFIG COPY menu) Setting data of the INPUT CONFIG and SYSTEM CONFIG (except the DEGAUSS DELAY data) menus can be copied from the serial connected monitor. The SYSTEM CONFIG (2/2) menu is used for the following settings: • Display mode and position of the signal format (FORMAT DISPLAY and POSITION menus) • Display mode and position of the channel number (CH NO and POSITION menus) • Display mode and position of the channel name (CH NAME and POSITION menus) • Display mode of the caption (CAPTION menu) • Maintenance (MAINTENANCE menu) This is for a service qualified personnel. 39 (E) Chapter 2 Menu Chapter 2 Menu How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. the Screen Display — SYSTEM CONFIG Menu Structure of the SYSTEM CONFIG Menu Level 1 Level 2 LAST CH x MONITOR ADDRESS E11 ENTER PASSWORD Setting Lists of the SYSTEM CONFIG Menu This section explains the setting lists displayed in the menu. How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. For more information about the menu number, see “About menu numbers” on page 26(E). • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. • The factory setting is shown in the brackets. 40 (E) [E] (1/2) SYSTEM CONFIG (1/2) menu Set each of the following items. STANDBY MODE: Select the power-up condition when the MAIN POWER switch is turned on (BVM-D14H1U/D14H1E/D14H1A/D14H5U/ D14H5E/D14H5A) or when the battery is installed (BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A.) ON: Standby mode [OFF]: Operation mode DEFAULT CH: Select the power-up input channel (LAST or CH x). [LAST]: Set the channel to the channel that was selected at the time the power was last turned off. CH x: Set the channel to a specific channel number. DEGAUSS DELAY: Set the time between power-up and the beginning of degaussing. Enter the desired time (in seconds, 0 to 255). CONT/BRT HOLD: Select the contrast and brightness settings to the center or adjusted value after adjusting the white balance or auto adjustment of CONTROL PRESET ADJ (OFF or ON). ON: The contrast and brightness are set to the value before adjusting. [OFF]: The contrast and brightness are set to the center value (100) after adjusting. COL TEMP SHORT-CUT: Assign the shortcut function to the MANUAL menu of the COLOR TEMP ADJ menu to [F2] key (OFF or F2). F2: Assigns the shortcut to the MANUAL menu of the COLOR TEMP ADJ menu. [OFF]: Does not assign the shortcut to the MANUAL menu of the COLOR TEMP ADJ menu. ACC SW: Set the automatic color control switch (OFF or ON). CONFIG COPY...: Copy setting data of the INPUT CONFIG and SYSTEM CONFIG (except the DEGAUSS DELAY data) menus from the serial connected BVM-D9H/D14H monitor. ÷[E11] [E11] MONITOR ADDRESS menu Set the address number of the monitor to be copied. [E] (2/2) SYSTEM CONFIG (2/2) menu Select items to be displayed on the screen. FORMAT DISPLAY: Select the display mode of the signal format. ÷[E2] (2/2) POSITION: Select the display position of the signal format. ÷[E2] (2/2) CH NO: Select the display mode of the channel number. ÷[E3] (2/2) POSITION: Select the display position of the channel number. ÷[E3] (2/2) CH NAME: Select the display mode of the channel name. ÷[E4] (2/2) POSITION: Select the display position of the channel name. ÷[E4] (2/2) CAPTION: Select the caption display mode. ÷[E5] (2/2) MAINTENANCE...: Menu for service personnel. [E2] (2/2) FORMAT DISPLAY and POSITION menus FORMAT DISPLAY menu Select the display mode of the signal format. [AUTO]: Disappears after displayed for a while. ON: Displayed. OFF: Not displayed. POSITION menu Select the display position. [BOTTOM LEFT] BOTTOM CENTER BOTTOM RIGHT TOP LEFT TOP CENTER TOP RIGHT [E3] (2/2) CH NO and POSITION menus CH NO menu Select the display mode of the channel number. [AUTO]: Disappears after displayed for a while. ON: Displayed. OFF: Not displayed. POSITION menu Select the display position. BOTTOM LEFT BOTTOM CENTER [BOTTOM RIGHT] TOP LEFT TOP CENTER TOP RIGHT [E4] (2/2) CH NAME and POSITION menus CH NAME menu Select the display mode of the channel name. [AUTO]: Disappears after displayed for a while. ON: Displayed. OFF: Not displayed. POSITION menu Select the display position. BOTTOM LEFT BOTTOM CENTER BOTTOM RIGHT [TOP LEFT] TOP CENTER TOP RIGHT [E5] (2/2) CAPTION menu Select the caption display mode. [OFF]: Not displayed CAPTION 1: Displayed in CAPTION 1 mode. CAPTION 2: Displayed in CAPTION 2 mode. TEXT 1: Displayed in TEXT 1 mode. TEXT 2: Displayed in TEXT 2 mode. 41 (E) Chapter 2 Menu SYSTEM CONFIG (1/2) @STANDBY MODE @DEFAULT CH @DEGAUSS DELAY @CONT/BRT HOLD @COL TEMP SHORT-CUT @ACC SW @CONFIG COPY E1 SYSTEM CONFIG (2/2) @FORMAT DISPLAY E2 @POSITION @CH NO E3 @POSITION @CH NAME E4 @POSITION @CAPTION E5 @MAINTENANCE Chapter 2 Menu BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu 1-23 1-24 F Displaying Information About the Monitor — STATUS Menu the Picture — ALIGNMENT Menu Overview Overview The STATUS menu is used to view general data about the monitor and information about signals assigned to the slots in the rear panel. • Data about the current channel (STATUS menu (1/2)) • Data about the monitor in use and data about the input adaptors installed into the slots on the rear panel (STATUS menu (2/2)) Structure of the STATUS Menu V SIZE V CENTER H SIZE H PHASE H PIN H KEY Level 2 STATUS (2/2) F2 MODEL NAME SERIAL NO Setting Lists of the ALIGNMENT Menu This section explains the setting lists displayed in the menu. Setting Lists of the STATUS Menu This section explains the setting lists displayed in the menu. How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. For more information about the menu number, see “About menu numbers” on page 26(E). BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A • The arrow mark (÷) refers you to another setting list that appears after you make the setting, or to an operation that is carried out as a result of the setting. When there is no arrow mark, the menu does not have any sub-list. [F] STATUS menu Select the STATUS menu 1/2 or 2/2. ÷[F1] [F1] STATUS (1/2) menu Data about the current channel is displayed. CH: channel number SL: slot number IN: input connector number FORMAT: format of the input signal NAME: channel name 42 (E) Structure of the ALIGNMENT Menu Level 1 STATUS (1/2) F1 SLOT 1 F3 The ALIGNMENT menu is used for adjusting the position, size and geometry of the picture. Chapter 2 Menu Chapter 2 Menu The following information is displayed on the two pages of the STATUS menu. Level 1 G Adjusting the Position, Size and Geometry of [F2] STATUS (2/2) menu Data about the monitor is displayed at the upper half of the display. MODEL NAME: model name SERIAL NO: serial number OPERATION TIME: operation time (in hours) SOFTWARE VERSION: software version How to read the setting lists • For purposes of explanation, each setting list is preceded by a menu number. These numbers are not displayed on the screen. For more information about the menu number, see “About menu numbers” on page 26(E). Data about the input adaptors installed into the respective slots in the rear panel is displayed at the lower half of the display. When the BKM-129X is installed in SLOT 1, the following is displayed. When any optional boards are not installed, EMPTY is displayed for SLOT 2 and SLOT 3. SLOT1: COMPONENT ÷[F3] SLOT2: EMPTY ÷[F3] SLOT3: EMPTY ÷[F3] [F3] SLOT 1 to 3 menu Select the desired slot. Data about the optional board installed in the selected slot is displayed. MODEL NAME: Model name of that optional board SERIAL NO: Serial number of that circuit board 43 (E) [G] ALIGNMENT menu Adjust the position, size or geometry of the picture with the UP and DOWN buttons or PHASE knob. Selecting the Monitor to Control — ADDRESS Menu Overview A D D R ES S - - - V SIZE: Adjust the height of the picture. S I N G LE * * * G R O U P * * * A L L A L L A L L P O W E R P O W E R O N O FF D I S P L A Y M O N IT O R D I S P L A Y G R O UP Chapter 2 Menu When multiple monitors are connected by a serial remote connection, the ADDRESS menu is used to choose whether one particular monitor or monitor group will be controlled, or whether operations are to be performed on all monitors together. Chapter 2 Menu BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G Adjusting the Position, Size and Geometry of the Picture — ALIGNMENT Menu A D D R E SS A D D R E S S Displaying the ADDRESS Menu ADDRESS Menu Press the ADDRESS button. The ADDRESS menu is displayed on the screen. By pressing the ENTER or Ent button after selecting the item, serial remote operation becomes activated. V CENTER: Adjust the vertical picture position. Settings made with the menu items are as follows: H SIZE: Adjust the width of the picture. H PHASE: Adjust the horizontal picture position. Item Function SINGLE Controls only a specified monitor. Enter the monitor address number. GROUP Controls only a specified monitor group. Enter the group address number. ALL Controls all monitors. ALL POWER ON Turns all connected monitors on. ALL POWER OFF Turns all connected monitors off. DISPLAY MONITOR ADDRESS When this item is selected, each connected monitor displays its monitor address on its screen. DISPLAY GROUP ADDRESS When this item is selected, each connected monitor displays its group address on its screen. Notes H PIN: Correct side pincushion distortion. • To remotely control monitors connected in serial, MONITOR ADDRESS or GROUP ADDRESS of monitors should be correctly set in the REMOTE menu. For details of the REMOTE menu, see “[D] Assigning the Remote Control Functions – REMOTE Menu” on page 37(E). H KEY: Correct trapezoid distortion. - In GROUP or ALL mode, the LEDs of the function buttons will not light with controlled from the menu. (LEDs light only when you press the function button.) - In GROUP or ALL mode, LEDs of controlled monitor will light as follows. • In case of SHIFT OFF before remote control operation: LEDs light in green when the SHIFT button is remotely set to OFF. For details, see “SHIFT button” on page10(E) for BVMD9H5U/D9H5E/D9H5A or on page 19(E) for BVMD14H5U/D14H5E/D14H5A. • In case of SHIFT ON before remote control operation: LEDs light in amber when the SHIFT button is remotely set to ON. For details, see “SHIFT button” on page11(E) for BVMD9H5U/D9H5E/D9H5A or on page 20(E) for BVMD14H5U/D14H5E/D14H5A. (continued) 44 (E) 45 (E) 1-25 1-26 Selecting the Monitor to Control — ADDRESS Menu To cancel the remote control mode, press the ADDRESS button. When selecting the monitor, short-cut function will enable to select the target monitor without using the items in the ADDRESS menu. The operation procedure is as follows. To select the monitor in the SINGLE mode To exit the ADDRESS menu, press the ADDRESS button or the MENU button. 1 2 Press the ADDRESS button. Press the address number of the target monitor. Press one digit address number on the numeric keypad when it is from 1 to 9. Press three digits address number (press 0 button and then press the two-digit address number) when it is from 10 to 99. To select the monitors in the GROUP mode 1 2 3 Press the ADDRESS button. Press the F1 button. Press the group number of the target monitor. Press one digit group address number when it is from 1 to 9. Press three digits group address number (press 0 button and then press the two-digit group number) when it is from 10 to 99. To select all the monitors in the ALL mode BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1 2 46 (E) Press the ADDRESS button. Press the F2 button. Nominal chromaticity coordinates: General EBU phosphor System 15.625 kHz – 45 kHz (For details, see “Available Signal Format” on page 53(E).) CRT BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/ D9H5A HR Trinitron, 4:3 aspect ratio Aperture grille pitch: 0.25 mm 90 degree deflection, 21.6 mm diameter in-line gun Effective picture size with 16:9 aspect ratio: 155.4 × 87.4 mm (6 1/8 × 3 1/2 inches) (w/h) 178 mm (7 inches) (diagonal size) Effective picture size with 4:3 aspect ratio: 155.4 × 115 mm (6 1/8 × 4 5/8 inches) (w/h) 190.7 mm (7 1/2 inches) (diagonal size) CRT protection: EHT (extremely high tension) protection type Warm-up time: approx. 30 minutes Anode voltage: 15 kV with no beam current R x y 0.640 0.330 G 0.290 0.600 B 0.150 0.060 Dimensions (w/h/d) BVM-D9H1U/D9H1E/D9H1A: approx. 217 × 174 × 364.5mm (8 5/8 × 6 7/8 × 14 3/8 inches) when the AC adaptor is installed: approx. 217 × 174 × 419.5mm (8 5/8 × 6 7/8 × 16 5/8 inches) BVM-D9H5U/D9H5E/D9H5A: approx. 217 × 218 × 364.5mm (8 5/8 × 8 5/8 × 14 3/8 inches) when the AC adaptor is installed: approx. 217 × 218 × 419.5mm (8 5/8 × 8 5/8 × 16 5/8 inches) BVM-D14H1U/D14H1E/D14H1A: approx. 346 × 280 × 519mm (13 5/8 × 11 1/8 × 20 1/2 inches) BVM-D14H5U/D14H5E/D14H5A: approx. 482 × 280 × 519mm (19 × 11 1/8 × 20 1/2 inches) BVM-D14H1U/D14H1E/D14H1A/D14H5U/ D14H5E/D14H5A HR Trinitron, 4:3 aspect ratio Aperture grille pitch: 0.25 mm 90 degree deflection, 29.4 mm diameter in-line gun Effective picture size with 16:9 aspect ratio: 267.5 × 150.5 mm (10 5/8 × 6 inches) (w/h) 306.9 mm (12 1/8 inches) (diagonal size) Effective picture size with 4:3 aspect ratio: 267.5 × 200.6 mm (10 5/8 × 8 inches) (w/h) 331.6 mm (13 1/8 inches) (diagonal size) CRT protection: EHT (extremely high tension) protection type Warm-up time: approx. 30 minutes Anode voltage: 23 kV with no beam current 47 (E) Chapter 3 Appendix Chapter 2 Menu Exiting the ADDRESS Menu Short-cut Function in the ADDRESS Menu Chapter 3 Appendix Cancelling the Remote Control Mode Specifications BVM-D14H1U/D14H1E/D14H1A 217 (8 5/8) Side 352.5 (14) 131.5 (5 1/4) 15 (19/32) 8 ∅20 (13/16) (11/32) 163 (6 1/2) 28 (1 1/8) 265 (10 1/2) 85 (3 3/8) 5 (7/32) 85 (3 3/8) 170 (6 3/4) 3.5 (5/32) 217 (8 5/8) 28 (1 1/8) 260 (10 1/4) 340 (13 1/2) 12 (1/2) 346 (13 5/8) 30 (1 3/16) 482 (19) 174.5 (6 7/8) Side Side Side 12 500 43 12 60 (2 3/8) 263 (10 3/8) 352.5 (14) 12 ( 1/ 2) 45.5 (1 13/16) 130 31 (1 1/4) 500 60 (2 3/8) 263 (10 3/8) Rear Rear 162 (6 1/2) 218 (8 5/8) 90 370 90 370 Rear Rear When using stand 340 (13 1/2) 302 (12) 260 (10 1/4) 18° 48 (E) 49 (E) Chapter 3 Appendix ∅22 (7/8) Front 170 (6 3/4) 210 (8 3/8) Unit: mm (inches) Front 163 (6 1/2) Unit: mm (inches) Front Front 131.5 (5 1/4) BVM-D9H1U/D9H1E/D9H1A BVM-D14H5U/D14H5E/D14H5A Unit: mm (inches) Unit: mm (inches) 265 (10 1/2) BVM-D9H5U/D9H5E/D9H5A 15 (19/32) Dimensional drawing Chapter 3 Appendix BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Specifications 1-27 1-28 Specifications Mass BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Peak inrush current (1) Power ON, current probe method: 80 A (240 V) (BVMD9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A), 45 A (240 V) (BVM-D14H1U/ D14H1E/D14H1A/D14H5U/ D14H5E/D14H5A) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 10 A (230 V) (BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A), 20 A (230 V) (BVM-D14H1U/ D14H1E/D14H1A/D14H5U/ D14H5E/D14H5A) Power requirements BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A: AC 100 to 240 V, 50/60 Hz, DC 12V+5 -1 V BVM-D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A: AC 100 to 240 V, 50/60 Hz Input/output connectors Video input/output BNC type × 3 (with loop-through outputs, 75-ohm automatic termination) R/G/B: 1 Vp-p ±6 dB, positive, high impedance Y: 1 Vp-p ±6 dB, high impedance PB/PR: 0.7 Vp-p ±6 dB, high impedance Sync input/output BNC type × 1 (with loop-through output, 75-ohm automatic termination) Composite sync: 0.3 to 8 Vp-p, positive/negative tri-level sync signal input or negative bi-level sync signal input, high impedance Return loss More than 40 dB (10 MHz, with 75-ohm termination) Remote control OPTION: Mini-DIN 8-pin × 1 CONTROL UNIT: D-sub 9-pin × 1 (BVM-D9H1U/ D9H1E/D9H1A1), BVMD14H1U/D14H1E/D14H1A only) PARALLEL REMOTE 1: D-sub 9-pin × 1 PARALLEL REMOTE 2: Modular connector 6-pin SERIAL REMOTE: D-sub 9-pin × 21) (with loop-through output) Audio input (BVM-D9H5U/D9H5E/D9H5A only) Phono jack × 3 (with loop-through output) Convergence error Video signal Frequency response 575/50I, 480/60I component inputs BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A/ D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A: 50Hz to 10MHz (0 dB/–3 dB) Models other than the above or RGB inputs BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A: 48 Hz to 17 MHz, (1 dB/ –3 dB) BVM-D14H1U/D14H1E/ D14H1A/D14H5U/D14H5E/ D14H5A: 48 Hz to 24 MHz, (0 dB/ –3 dB) Aperture compensation2) OFF: 0 dB ON: 2 dB to 6 dB 575/50I, 480/60I inputs: 5 MHz Input other than the above: 16 MHz Within a central area bounded by a circle with a diameter equal to the picture height. Less than 0.4 mm with a central area bounded by a circle and less than 0.7 mm at any other point. Standard luminescence 120 cd/m2 (at standard 1 Vp-p 100% white signal) Raster size stability Less than 1% of picture height (at 120 cd/m2 peak luminescence, 10 to 90% APL) Resolution (at screen center, 120 cd/m2 luminescence) BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A: 340 TV lines (16:9) 450 TV lines (4:3) BVM-D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A: 600 TV lines (16:9) 800 TV lines (4:3) Picture performance Operating conditions Normal scan Temperature 0°C to 35°C (32°F to 95°F) Optimum temperature 20°C to 30°C (68°F to 86°F) Humidity 0% to 90% (no condensation) Pressure 700 hPa to 1060 hPa Underscan Linearity 5% overscan of CRT effective screen area (adjustable range greater than ±15%) 3% underscan of CRT effective screen area (adjustable range greater than ±15%) Within a central area bounded by a circle with a diameter equal to the picture height, less than 1.0 % of the picture height, and outside the same area, about 2.0 % of the picture height Storage and transport conditions Temperature Humidity Pressure –10°C to 40°C (14°F to 104°F) 0% to 90% 700 hPa to 1060 hPa Color temperature D93, D65 (adjustable to other color temperatures) ................................................................................................................................................................................................................................................ ............................................................................................................................................................................................................................................. 1) BVM-D9H1U/D9H1E/D9H1A is swithced to REMOTE or CTRL UNIT with the select switch. 2) The aperture cannot be compensated for RGB input signals. 50 (E) 51 (E) Chapter 3 Appendix Chapter 3 Appendix BVM-D9H1U/D9H1E/D9H1A: approx. 8.1 kg (17 lb 14 oz) when the AC adaptor is installed: approx. 8.9 kg (19 lb 10 oz) BVM-D9H5U/D9H5E/D9H5A: approx. 9.3 kg (20 lb 8 oz) when the AC adaptor is installed: approx. 10.1 kg (22 lb 4 oz) BVM-D14H1U/D14H1E/D14H1A: approx. 21 kg (46 lb 5 oz) BVM-D14H5U/D14H5E/D14H5A: approx. 23 kg (50 lb 11 oz) Power consumption BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A: 85 W max. (an optional BKM142HD or BKM-120D is installed) 60 W typical (the supplied analog component input adaptor is installed) BVM-D14H1U/D14H1E/D14H1A/ D14H5U/D14H5E/D14H5A: 115 W max. (an optional BKM142HD or BKM-120D is installed) 100 W typical (the supplied analog component input adaptor is installed) Accessories supplied AC power cord (1) AC adaptor (1) (BVM-D9H1U/D9H1E/D9H1A/ D9H5U/D9H5E/D9H5A only) AC plug holder (1) Tally plate (1) 4:3 mask (1) Operation manual (1) Acquired safety regulations UL1950, CSA950 FCC Class A, IC Class A DHHS, DNHW TÜV (EN60950), PTB CE-Marking, C-tick Mark Available Signal Format System Total lines Active per frame lines per frame ** Frame rate (Hz) Scanning format Aspect Standard 575/50I (*PAL) 625 575 25 2:1 interlace 16:9/4:3 ITU 601 480/60I (*NTSC) 525 483 30 2:1 interlace 16:9/4:3 ITU 601 575/50P 625 575 50 Progressive 16:9/4:3 – 480/60P 525 483 60 Progressive 16:9/4:3 SMPTE 293M 1080/48I 1125 1080 24 2:1 interlace 16:9 – 1080/50I 1125 1080 25 2:1 interlace 16:9 SMPTE 294M 1035/60I 1125 1035 30 2:1 interlace 16:9 BTA S-001B 1080/60I 1125 1080 30 2:1 interlace 16:9 SMPTE 274M/BTA S-001B 720/60P 750 720 60 Progressive 16:9 SMPTE 296M * Available when the optional adaptor is installed. ** Also compatible with 1/1.001. Design and specifications are subject to change without notice. 52 (E) 53 (E) Chapter 3 Appendix Chapter 3 Appendix BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Specifications 1-29 1-30 Specifications Connection cable for PHILIPS PM 5639 probe (corresponds to PHILIPS PM 5639/64 cable) Connection Cable Specifications for Color Temperature Probes Special cables are required to connect color temperature probes other than the Sony BKM-14L to the monitor. The following diagrams show specifications and pin assignments for the required cables. Modular connector 1 6 2 Connection cable for GRASEBY SLS 9400 probe Modular connector Mini DIN 8-pin connector (male) 6 Chapter 3 Appendix 2 1 5 3 8 Signal 6 Pin Number 3 8 6 Signal Pin Number +5V 1 1 NC N.C. 2 2 NC RXD 3 3 RTS TXD 4 4 GND N.C. 5 5 N.C. GND 6 6 TXD Signal Pin Number Signal Pin Number N.C. 1 1 NC 7 +5V GND 2 2 NC 8 RXD RXD 3 3 RTS TXD 4 4 GND GND 5 5 N.C. N.C. 6 6 TXD 7 +5V 8 RXD Connection cable for THOMA TF6 probe D-sub 15-pin connector (female) 1 D-sub 25-pin connector (male) 1 Mini DIN 8-pin connector (male) 2 1 5 Signal 25 Pin Number 2 1 5 13 14 Mini DIN 8-pin connector (male) 8 Connection cable for MINOLTA CA-100 probe BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 54 (E) 1 5 3 8 Signal 6 Pin Number N.C. 1 1 NC TXD 2 2 NC RXD 3 3 RTS RTS 4 4 GND CTS 5 5 N.C. N.C. 6 6 TXD GND 7 7 +5V N.C. 8 to 25 8 RXD 9 15 3 8 6 Signal Pin Number N.C. 1 1 NC RXD 2 2 NC TXD 3 3 RTS N.C. 4 4 GND N.C. 5 5 N.C. N.C. 6 6 TXD GND 7 7 +5V N.C. 8 to 15 8 RXD Signal Pin Number 55 (E) Chapter 3 Appendix 1 Mini DIN 8-pin connector (male) The menu index shows the menu items provided with this monitor in alphabetical order. For you reference, each menu item is followed by the page of this manual on which the item is explained, its menu number, and the Main Menu that the item belongs to. Menu Item Menu Item M Menu number 41(E) 45(E) 34(E) 44(E) 36(E) 36(E) 32(E) – – – [G] – – [A2] SYSTEM CONFIG menu ADDRESS menu COLOR TEMP ADJ menu ALIGNMENT menu INPUT CONFIG menu INPUT CONFIG menu CONTROL PRESET ADJ menu B BRIGHT 32(E) – CONTROL PRESET ADJ menu C CAM CAPTION CH CH NAME CH NO CHANNEL NAME CHROMA COL TEMP SHORT-CUT COL1 COL2 COLOR TEMP COLOR TEMP ADJ CONFIG COPY CONT/BRT HOLD CONTRAST CONTROL PRESET ADJ COPY 36(E) 41(E) 38(E) 40(E) 41(E) 41(E) 36(E) 32(E) 41(E) 34(E) 34(E) 36(E) 33(E) 41(E) 41(E) 32(E) 31(E) 34(E) – [E5] [D211] – [E4] [E3] [C2] – – – – – [B] [E1] – – [A] [B3] INPUT CONFIG menu SYSTEM CONFIG menu REMOTE menu SYSTEM CONFIG menu SYSTEM CONFIG menu SYSTEM CONFIG menu INPUT CONFIG menu CONTROL PRESET ADJ menu SYSTEM CONFIG menu COLOR TEMP ADJ menu COLOR TEMP ADJ menu INPUT CONFIG menu COLOR TEMP ADJ menu SYSTEM CONFIG menu SYSTEM CONFIG menu CONTROL PRESET ADJ menu CONTROL PRESET ADJ menu COLOR TEMP ADJ menu D1-SDI D65 D93 DEFAULT CH DEGAUSS DELAY 36(E) 34(E) 34(E) 40(E) 40(E) – – – – – INPUT CONFIG menu COLOR TEMP ADJ menu COLOR TEMP ADJ menu SYSTEM CONFIG menu SYSTEM CONFIG menu EDIT EIA COLOR BAR ENTER PASSWORD EXT SYNC SLOT 36(E) 32(E) 40(E) 36(E) – – – – INPUT CONFIG menu CONTROL PRESET ADJ menu SYSTEM CONFIG menu INPUT CONFIG menu FORMAT FORMAT DISPLAY FULL FIELD WHITE 100 % 36(E) 41(E) 31(E) [C1] [E2] – G GROUP ADDRESS 38(E) H H KEY H SIZE H PHASE MAINTENANCE MANUAL MARKER PHASE MARKER WIDTH MODEL NAME MONITOR ADDRESS Main menu Page Menu number 40(E) 32(E) 34(E) 36(E) 36(E) 42(E) 38(E) 41(E) [E5] [A1] [B1] – – – – [E11] Main menu SYSTEM CONFIG menu CONTROL PRESET ADJ menu COLOR TEMP ADJ menu INPUT CONFIG menu INPUT CONFIG menu STATUS menu REMOTE menu SYSTEM CONFIG menu N NEW NAME NTSC, PAL NTSC SET UP 36(E) 36(E) 36(E) – – – P PARALLEL REMOTE PARALLEL REMOTE CONFIG PHASE POSITION PROBE PROG 38(E) 38(E) 32(E) 41(E) 34(E) 36(E) – [D2] – – – – R REMOTE RGB R OFF 37(E) 35(E) 38(E) [D] – [D211] S SERIAL NO SERIAL REMOTE SLOT 1 SLOT NO SMPTE COLOR BAR STANDBY MODE START STATUS STD SYSTEM CONFIG 42(E) 38(E) 42(E) 36(E) 32(E) 40(E) 34(E) 42(E) 34(E) 39(E) – [D1] [F3] – – – – [F] – [E] V V CENTER V SIZE VTR 44(E) 44(E) 36(E) – – – ALIGNMENT menu ALIGNMENT menu INPUT CONFIG menu X X 34(E) – COLOR TEMP ADJ menu Y Y YPBPR YPBPR MATRIX 34(E) 36(E) 36(E) – – – COLOR TEMP ADJ menu INPUT CONFIG menu INPUT CONFIG menu 1 1125/60I SYSTEM 1 PIN 36(E) 38(E) – [D21] 2 2 PIN 38(E) – REMOTE menu 3 3 PIN 38(E) – REMOTE menu INPUT CONFIG menu SYSTEM CONFIG menu CONTROL PRESET ADJ menu 4 4 PIN 38(E) – REMOTE menu 5 5 PIN 38(E) – REMOTE menu – REMOTE menu 6 6 PIN 38(E) – REMOTE menu – – – – – – – ALIGNMENT menu ALIGNMENT menu INPUT CONFIG menu ALIGNMENT menu ALIGNMENT menu INPUT CONFIG menu COLOR TEMP ADJ menu 7 7 PIN 38(E) – REMOTE menu 8 H PIN HD-SDI HIGH LIGHT 44(E) 44(E) 36(E) 44(E) 44(E) 36(E) 34(E) 8COLOR BAR 100% 8COLOR BAR 75% 8 PIN 32(E) 32(E) 38(E) – – – CONTROL PRESET ADJ menu CONTROL PRESET ADJ menu REMOTE menu I INPUT CONFIG INPUT NO 35(E) 36(E) [C] – L LAST LOAD REF VALUE LOW LIGHT 40(E) 34(E) 34(E) – [B21] – D E F 56 (E) INPUT CONFIG menu INPUT CONFIG menu INPUT CONFIG menu REMOTE menu REMOTE menu CONTROL PRESET ADJ menu SYSTEM CONFIG menu COLOR TEMP ADJ menu INPUT CONFIG menu Chapter 3 Appendix Page ACC SW ADDRESS ADJUST ALIGNMENT APERTURE VALUE AUDIO INPUT AUTO A Chapter 3 Appendix BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Menu Index REMOTE menu INPUT CONFIG menu REMOTE menu STATUS menu REMOTE menu STATUS menu INPUT CONFIG menu CONTROL PRESET ADJ menu SYSTEM CONFIG menu COLOR TEMP ADJ menu STATUS menu COLOR TEMP ADJ menu SYSTEM CONFIG menu INPUT CONFIG menu REMOTE menu INPUT CONFIG menu INPUT CONFIG menu SYSTEM CONFIG menu COLOR TEMP ADJ menu COLOR TEMP ADJ menu 57 (E) 1-31 1-32 Menu Configuration MAIN MENU A1 M E N U C O L O R T E M P I N P U T C O N F I G... A D J ... A D J ... R E M O T E ... S Y S T E M C O N F I G ... S T A T U S ... A L I G N M E N T ... T O C A N C E L T O C O N F I R M :E N T E R C H R O M A : 1 00 P H A S E : 1 00 A :M E N U K E Y K E Y pC O N T R O L T E M P I N P U T C O N F I G... S T A T U S ... A L I G N M E N T ... C O N T R A S T : 1 00 B RI G H T : 1 00 D P R E S ET A D J F U L L A U T O ... p FI E L D WH I T E 8 C O L O R B A R 1 0 0 % 8 C O L O R B A R 7 5 % Set by automatic adjustment (using the color bar signal) 1 0 0% D1 S M P T E C O L O R B A R E I A C O L O R B AR B1(2/2) ↓ A D J ↓ A D J US T S T D C O P Y ... ↓ A D J US T G B L T : C O NT R A S T R E E N : L U E : U M I N A N C O C A N C E T O B R IG H C H RO M E :P H L : M C O N F I R M T A A S E E N U K K K K : E N T E R N N N E O B O B O B Y K E Y G : 0 5 0 0 R : 0 5 0 0 B2 P R O B E S T D p S T A R T P R O B E B K M - 1 4 L X 0 . 3 1 Y 0 . 3 2 L O W L I G H T ( 20 I R E ) 2 . H I G H L I G H T ( 1 00 I R E ) 1 2 L O A D R E F 3 9 7 0 G : 0 5 0 0 F R OM 2 O F F C O N F I G . 3 4 5 6 P I N ... P I N ... P I N ... P I N ... T A L L Y R E D TA L L Y G R E E N E X T S Y N C U N D E R S C A N 7 8 P I N ... P I N ... 1 6 : 9 M A R K E R E O O C ↓ M O D E O F F C H ... L A S T G U S S D E L A Y N T / B R T H O LD L T E M P S H OR T - C U T C S W 0 0 0 O F F O F F O N C O P Y ... 4 : 3 pC H - - - - 1 pR G P I N ... ↓ O F F O F F U N D E R S C A N 1 6 : 9 H D E L A Y V D E L A Y B O F F 4 : 3 M A R K E R C A P T I O N V I S IO N T A L L Y R E D E A M B T A L L Y G R E E N D E G A U S S P O W E R O FF X P O L T S Y N C E R T U R E N O U E O N L Y :Select the power-up condition. :Select the power-up input channel. :Set the time between power-up and the beginning of degaussing. :Select the CONT/BRT settings in the COLOR TEMP ADJ. :Set the short-cut function to the F2 key. :Set the automatic color control. E11 C O P Y pM O N I T O R F R OM A D D RE S S 0 0 1 You can copy the INPUT CONFIG menu and SYSTEM CONFIG menu (except DEGAUSS DELAY) from the monitor which you assign the address No. E(2/2) S Y S T E M B21 V A LU E E3 C H N O P O S I T I O N C H N A M E P O S I T I O N E5 You can copy the color temperature data. ↓ C O N F I G( 2 / 2 ) pF O R M A T D I S P L A Y P O S I T I O N BO T T O M E4 pD 6 5 D 9 3 C O P Y C H C O N F I G( 1 / 2 ) C O N F I G E2 V A L U E ... B3 S T D P I N ... R : 0 5 0 0 Select the probe for color temperature adjustment. :Select the probe (BKM-14L, SLS 9400, CA-100, TF6, or PM 5639) :Confirm/Change x, y value on the Chromaticity Coordinate and luminance R E F S T D 0 0 1 R E M OT E R E M OT E D C C A B I A S B : 0 5 0 0 1 P A R A L L E L P A R A L L E L E1 G A I N B : 0 5 0 0 C H A D D RE S S pS T A N D B Y D E F A U L T K N O B D211(2/2) 0 1 ↓ P I N ... 1 P I N ... 0 0 1 S Y S T E M S T D R E D C O N FI G p1 2 A D D RE S S E(1/2) ↓ T EM P p M A N U A L P R O B E ... D211(1/2) R E M O T E R E M O T E pM O N I T O R G R O U P Chapter 3 Appendix Chapter 3 Appendix C O L O R S T D S E R I A L D2 B1(1/2) B D21 R E M O T E A U T O p M A N U A L ... A D J ... A D J ... R E M O T E ... S Y S T E M C O N F I G ... A2 C O N T R O L P R E SE T C O L O R ↓ P R E SE T A B C D E F G Set the preset value with the adjustment knobs. ↓ pC O N T R O L M A N U AL ↓ M E N U ↓ MAIN MENU A B C D E F G A U T O L E F T A R I A T O P L U G U E T O P C A P T I O N M A I N T E N A N C E ... T H T F O T O T O F F :Select the display mode of the signal format and display position. :Select the display mode of the channel number and display position. :Select the display mode of the channel name and display position. :Select the caption display mode. :For qualified service personnel p C O L 1 C O L 2 C H S L F O R MA T ↓ N A M E 1 1 1 Y P B PR P R O G 2 2 1 N T S C 3 4 5 6 3 1 2 2 2 1 2 1 D Y N N 7 1 1 Y P B PR 8 3 1 D 1 - SD I 9 1 1 Y P B PR F O R M A T ↓ C O N F I G( 1 / 2 ) 1 N X U O Y P B P R S L O T 1 P U T N O T S Y N C S L OT D I O I N P U T L O R T E M P A P E R T U R E V A LU E C H A N N E L N A M E... 1 S L O T 1 1 S T D 1 0 0 P R O G Set input signal data for each channel. :Current channel is indicated. :Select the input signal type. :Select the slot number. :Select the input connector number. :Select the slot when the external sync signal is used. :Select the audio input number (BVM-D9H5 only) :Select the color temperature. :Enter the aperture adjustment value. :Give the channel name. (Select in the “C2” menu) C H C O N F I G( 2 / 2 ) ↓ 1 p1 1 2 5 / 6 0 I H P H A S E M A R K E R M A R K E R S Y ST E M 1 0 8 0 I 0 0 0 P H A S E W I D T H 0 0 0 0 0 0 N T S C S E T U P Y P B P R M A T R I X 7 . 5 6 0 I V C R O F F M O D E D (next page) 58 (E) S M P T E N T S C , P A L D 1 - S D I H D - S D I :Select the level of YPBPR signals. 1 P T T ( 1 / 2) B S S S P C C P A L D I R , P A L , P A L F2 S T A T U S M O D E L F3 ↓ B V M - D 9 H 5 U N O 2 0 0 1 2 3 4 SL O T 1 C O M P O N EN T M O D E L N A M E S E R I A L N O B K M - 1 2 9 X 9 0 7 1 5 0 1 O P E R A T I O N T I ME 0 0 0 1 2 3 H 1 . 0 0 S O F T W A R E V E R SI O N C2 :Current channel is indicated. :Select the number of active scanning lines per frame. :Set the holizontal picture position. :Set the 4:3 marker position. :Set the 4:3 marker width. :Set the NTSC setup level when the BKM-127W is installed. :Select the matrix when YPBPR signals of the signal formats 480/60I or 480/60P are input. :Select ON to compensate for a distorted picture when the input signals from the VCR are not typical. (Effective only when the signal formats 480/60I or 575/50I are input.) (2 / 2 ) N A M E S E R I A L C H A N N E L C H N A M E 1 pS L O T 1 pP R O G E D I T I N P U T C H 1 pY P B P R R G B C(2/2) ↓ BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A p F O R M A T ... S L O T N O I E A C ↓ I N P U T C H I N ↓ S T A T U S C1 C(1/2) ↓ F/F1 D 6 5 D 9 3 C O M P O NE N T S L O T 2 N T S C , PA L S L O T 3 D 1 - S D I :Data about the installed optional board is displayed. C A M V T R N E W N A M E G A L I G N ME N T pV V H H H H S I ZE 0 0 C E N T E R 0 0 S P P K 0 0 0 0 I H I E Z E A S E N Y Use for adjusting the position, size and geometry of the picture. 0 0 0 0 59 (E) Section 2 Service Informations 2-1. Circuit Boards Location HB (D14H5) HC (D14H5) YC C YA MA G1 HA (D14H5) MB YB G B B1 HD (D14H1) B2 T BX BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-1 2-2-1. Cabinet and Rear Panel Removal 7 Six screws (+BVTT 3 × 6) D14H1 8 Rear panel (Upper) 5 Four screws (Case screw OS) 7 Seven screws (+BVTT 3 × 6) 6 Cabinet (Upper) 3 Three screws (Case screw OS) 8 Rear panel (Upper) 4 Cabinet (L) 2 Cabinet (R) 2-2 1 Three screws (Case screw OS) BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-2-2. How To Open The B Board CN301 B2 board B1 board 3 Two PWB holders 4 B board 2 Handle plate 1 Two screws (+P 4 × 8) 2-2-3. Bezel Complete Assy Removal (1) D14H5 1 Three screws (+PSW 4 × 14) 2 Handle assy Connector (16P) Connector (8P) Connector (9P) Connector (16P) 5 Two screws (+B 4 × 8) Connector (7P) 7 Bezel complete assy 6 Two screws (+B 4 × 8) 4 Handle assy BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3 Three screws (+PSW 4 × 14) 2-3 (2) D14H1 2-2-4. HA, HB and HC Boards Removal (D14H5) 2-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-2-5. YA, YB and YC Boards Removal 6 YC insulator 7 Screw 5 Screw (+BVTP 3 × 10) (+BVTP 3 × 10) 8 YC board 1 Two claws 2 YA board 3 Screw (+BVTP 3 × 10) 4 YB board 2-2-6. G Board Removal 4 Screw (+PSW 3 × 12) 2 Rivet CN601 5 G board 3 Rear panel (Lower) 1 Tow screws (+PSW 4 × 8) BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-5 2-2-7. BX Board (BKM-129X) Removal and Check 3 Z COMPL (Part No. : A-1394-977-A) ∗ Insert the Z COMPL into the slot and insert the BX board (BKM-129X) into the connector on the Z COMPL. 1 Loosen two stopper screws. Three slots ∗ In case the interface board of option is attached, connect it to the Z COMPL in the same way. 2 Remove BX board (BKM-129X). BKM-127W BKM-120D BKM-142HD Note : The interface board can be attached to all slots. But, left side slot should be always used. 2-6 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-2-8. T Board Removal 1 Two blank panel assy CN801 CN805 CN806 4 T board 3 Four screws (+BVTT 3 × 6) BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2 BX board (BKM-129X) 2-7 2-2-9. M Block Assy (MA and MB Boards) Removal 2 Screw (+BVTT 3 × 6) CN1105 CN1106 CN103 CN101 CN1100 B SERVICE POSITION 3 Remove MA shield in the arrow B direction. MB board A MA board 1 Remove M block assy in the arrow A direction. C 4 Hang M block assy in the arrow C direction. 2-8 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-2-10. Picture Tube Removal DY spacer 1 Anode cap 4 Two position washer 9 Picture tube shield assy 2 C board 6 C board band 3 Four flange nut (M5) 7 Deflection yoke 8 DY shield 5 Picture tube • REMOVAL OF ANODE CAP Note: To eliminate electric shock hazard, when replacing the picture tube, short-circuit the anode of the picture tube and the high-voltage terminal of anode cap to the picture tube shield or carbon painted on the picture tube, after removing the anode. • Removal Procedure c b a b a (1) Turn up one side of the rubber cap in the direction indicated by arrow a. Anode button (2) Using a thumb, pull up the rubber cap firmly in the direction indicated by arrow b. • Handling Precautions (3) When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling up it in the direction of the arrow c. (1) Do not scratch the surface of anode cap with a sharp object. (2) Do not press the rubber so hard that it damages the inside of anode caps. A shatter-hook terminal is built into the rubber. (3) Do not turn the foot of the rubber over. The shatter-hook terminal will stick out or damage the rubber. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2-9 2-10 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Section 3 Set-Up Adjustments 3-1. Set-Up Adjustment When CRT is Replaced This section describes the adjustments to be performed when the CRT is replaced. [Preparations] . Required tools and measuring instruments 1. Signal generator YPB/YPR signal generator .1080/60i (1125) : SMPTE 274M standard/ BTA S-001 standard .1035/60i (1125) : BTA S-001 standard .720/60p : SMPTE 296M standard .480/60p (525P) : SMPTE 293M standard .480/60i (525) : ITU601 .1080/48i (1125) : — .1080/50i (1125) : SMPTE 274M standard .720/50p : — .575/50p (625P) : — .575/50i (625) : ITU601 NTSC analog composite signal generator HD SDI signal generator D1 SDI signal generator 2. BKM-127W (NTSC/PAL input adapter) 3. BKM-142HD (HD SDI input adapter) 4. BKM-120D (D1 SDI input adapter) 5. Oscilloscope 6. Luminance meter 7. Color analyzer (Minolta CA-100) 8. Cable of the following specifications to connect the RS-232C terminal of the CA-100 and the OPTION terminal of the monitor. HDM option connector side Mini DIN 8-pin . Operate the SYSTEM CONFIG menu as follows. Use the SYSTEM menu to select ALL SYSTEM with the RE-LOAD FACTORY DATA, and execute it. BVM-D14H1/D14H5 control panel SHIFT button Function buttons CONTRAST VR BRIGHT VR CA-100 RS-232C connector side D Sub 25-pin (male) 1 1 FG V SYNC 2 2 TXD RTS 3 3 RXD GND 4 4 RTS NC 5 5 CTS TXD 6 6 NC +5V 7 7 GND RXD 8 H SYNC . Setting the INPUT CONFIGURATION menu Set the INPUT CONFIGURATION menu of the SETUP menu as shown below unless otherwise specified. FORMAT ................................ YPBPR SLOT NO ................................ 1 INPUT NO .............................. 1 SYNC MODE ......................... INT APEARTURE VALUE .......... 100 CHANNEL NAME ................ PROG COLOR TEMP ....................... STD H PHASE ................................ 000 MARKER PHASE .................. 000 MARKER WIDTH ................. 000 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 8 NC 9 – 19 NC 20 DTR 21 – 25 NC 3-1 . Connection diagram Y/G terminal PB/B terminal PR/R terminal SYNC terminal SLOT No. 1 Component signal generator BKM-129X BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3-2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A [Focus Adjustment] 1. Connect the 1080/60i cross-hatch signal (see note) to the ANALOG Y/G input connector. Note: This is the 1125 (1080) cross-hatch signal. 2. Press the SHIFT button to set the SHIFT OFF. [The LED (orange) on top of the button turns off.] Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns on.] 3. Set the initial (default) value to the following DF adjustment data. FOCUS AMP : 27 FOCUS KEY : 07 Note: This menu is located in the directory under the DEFLECTION menu of the MAINTENANCE menu. 4. Adjust the FOUCS 1 control (horizontal focus adjustment) and the FOUCS 2 control (vertical focus adjustment) until the center of the screen has the optimum focus. 5. Connect the 1080/60i monoscope signal to the ANALOG Y/G input connector. 6. Check that the horizontal resolution higher than the specifications can be recognized. Specifications: 600 TV lines or more 7. Connect the 1080/60i cross-hatch signal to the ANALOG Y/G input connector. 8. Adjust the following DF adjustment data until the thickness of the cross-hatch lines at the corners of picture have the same thickness as those in the center of screen. FOCUS AMP FOCUS KEY Note: If the uniformity is extremely poor, compromise so that the FOCUS AMP is not adjusted to the best focus but is adjusted to obtain the reasonable uniformity and good focus at the same time. 9. Copy the adjustment data that is obtained in step 8 to the MODE2 to MODE4, MODE7 to MODE10, MODE15 to MODE18, MODE21 to MODE24, MODE29 to MODE32 in this order. 10. Connect the 480/60i cross-hatch signal (see note) to the ANALOG Y/G input connector. Note: NTSC cross-hatch signal 11. Adjust the following DF adjustment data until the thickness of the cross-hatch lines at the corners of picture have the same thickness as those in the center of screen. FOCUS AMP FOCUS KEY BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 12. 13. 14. 15. Note: If the uniformity is extremely poor, compromise so that the FOCUS AMP is not adjusted to the best focus but is adjusted to obtain the reasonable uniformity and good focus at the same time. Copy the adjustment data that is obtained in step 11 to the MODE11, MODE12, MODE14 and MODE25 to MODE28 in this order. Connect the 720/60p cross-hatch signal to the ANALOG Y/G input connector. Adjust the following DF adjustment data until the thickness of the cross-hatch lines at the corners of picture have the same thickness as those in the center of screen. FOCUS AMP FOCUS KEY Note: If the uniformity is extremely poor, compromise so that the FOCUS AMP is not adjusted to the best focus but is adjusted to obtain the reasonable uniformity and good focus at the same time. Copy the adjustment data that is obtained in step 14 to the MODE6, MODE19 and MODE20 in this order. FOCUS 1 FOCUS 2 Fig. 1-1 3-3 (1) 60 Hz system Mode Signal format MODE1 1080/60i MODE2 (1125) MODE3 1035/60i MODE4 (1125) MODE5 720/60p MODE6 MODE7 480/60p MODE8 (525) MODE9 MODE10 MODE11 480/60i MODE12 (525) MODE13 MODE14 (2) 50 Hz system Mode Signal format MODE15 1080/48i MODE16 (1125) MODE17 1080/50i MODE18 (1125) MODE19 720/50p MODE20 MODE21 575/50P MODE22 (625) MODE23 MODE24 MODE25 575/50i MODE26 (625) MODE27 MODE28 3-4 16 : 9 16 : 9 16 : 9 16 : 9 4:3 16 : 9 4:3 16 : 9 16 : 9 16 : 9 16 : 9 4:3 16 : 9 4:3 Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN Adjustment procedure Perform the adjustment of step 1 to step 8. Copy the MODE 1 data. Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN Adjustment procedure Copy the MODE 1 data. Perform the adjustment of step 10 to step 11. Copy the MODE 5 data. Copy the MODE 1 data. Copy the MODE 13 data. Perform the adjustment of step 10 to step 11. Copy the MODE 13 data. Copy the MODE 1 data. Copy the MODE 5 data. Copy the MODE 1 data. Copy the MODE 13 data. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A [Landing Adjustment] 1. Connect the 480/60i entire-white signal (see note) to the ANALOG Y/G input connector. Note: This is the NTSC entire-white signal. 2. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 3. Press the 16:9 button to the OFF position to set the 4:3 mode. [The LED (orange) on top of the button turns off.] 4. Direct the CRT screen toward east (or west). Press the DEGAUSS button. 5. Set the Purity knob in the mechanical center. Purity 6-pole 4-pole Red Green Blue Fig. 1-4 10. Move back the DY so that the entire screen shows the green only. 11. Connect the 480/60i cross-hatch signal (see note) to the ANALOG Y/G input connector. Note: This is the NTSC cross-hatch signal. 12. Adjust the DY inclination. After DY inclination adjustment is complete, tighten the DY fixing screw. 13. Fix the deflection yoke (DY) using the three DY spacers. DY spacers Fig. 1-2 6. Push the DY (deflection yoke) to the front as far as it can go. 7. Fix the neck assembly in the position as shown in Fig. 1-3. Neck assy Deflection yoke (DY) Fig. 1-5 . Final adjustment When the adjustment is complete, check that mislanding (landing error) does not occur even when the monitor is directed in all directions of east, west, south and north. Fig. 1-3 8. Change the screen display to all green only as follows. [While the SFHIT is ON (the orange LED on the SHIFT button turns on), press the R and B button to ON. (The orange LED on the SHIFT button turns on.)] 9. Adjust the Purity knob until green comes to the center of the display as shown in Fig. 1-4. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3-5 [H Blanking Adjustment] . Preparation 1. Connect the monoscope signal of the signal formats that are shown in the following table, to the ANALOG Y/G input connector. Perform the H blanking adjustment in the respective screen modes using the respective signal formats. 60 Hz system Mode Signal format MODE1 1080/60i MODE2 (1125) MODE3 1035/60i MODE4 (1125) MODE5 720/60p MODE6 MODE7 480/60p MODE8 (525) MODE9 MODE10 MODE11 480/60i MODE12 (525) MODE13 MODE14 50 Hz system Mode Signal format MODE15 1080/48i MODE16 (1125) MODE17 1080/50i MODE18 (1125) MODE19 720/50p MODE20 MODE21 575/50P MODE22 (625) MODE23 MODE24 MODE25 575/50i MODE26 (625) MODE27 MODE28 16 : 9 16 : 9 16 : 9 16 : 9 4:3 16 : 9 4:3 16 : 9 16 : 9 16 : 9 16 : 9 4:3 16 : 9 4:3 Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN 2. Increase the brightness by adjusting the BRIGHT control so that blanking becomes visible on screen. Note: The following adjustment menus are located in the directory under the DEFLECTION menu of the MAINTENANCE menu. H BLK LEFT H CENT H BLK RIGHT H PHASE H SIZE 3-6 . H. Blanking Adjustment 1. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 2. To select the 4:3 mode of the adjustment, press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. To select the 16:9 mode of the adjustment, press the 16:9 ON button [to turn on the LED (orange)] to select the 16:9 mode. 3. Press the SHIFT button to OFF. [The LED (orange) on top of the button turns off.] 4. To select the NORMAL mode of adjustment, press the ) to its OFF position to UNDER SCAN button ( select the normal mode. [The green LED turns off.] To select the UNDER SCAN mode of adjustment, press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns on.] 5. Set the following adjustment data to adjustment points as shown below. H BLK LEFT : 255 H BLK RIGHT : 0 6. Adjust the H SIZE data so that the entire raster area is visible on screen. 7. Adjust the H CENTER data so that the raster is position just in the center of the screen (so that A = B). (Fig. 1-6) Effective screen area Deflection area (raster area) Signal display area A B H CENTER A=B C D H PHASE C=D Fig. 1-6 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 8. Adjust the H PHASE data so that the monoscope picture is positioned just in the center of the raster (so that C = D). 9. Adjust the H BLK RIGHT data so that the horizontal blanking is positioned 0 to 2 mm outside the right end of the monoscope signal display area. (Fig. 1-7) 10. Adjust the H BLK LEFT data so that the horizontal blanking is position 0 to 2 mm outside the left end of the monoscope signal display area. (Fig. 1-7) 11. Return the H SIZE data to the original data size. [V Blanking Adjustment] . Preparation 1. Connect the monoscope signal of the signal formats that are shown in the following table, to the ANALOG Y/G input connector. Perform the V blanking adjustment in the respective screen modes using the respective signal formats. 60 Hz system Mode Signal format Screen mode MODE9 480/60p (525) 4:3 NORMAL MODE13 480/60i (525) 4:3 NORMAL 50 Hz system Mode Signal format MODE23 575/50p (625) MODE27 575/50i (625) Signal display area 4:3 4:3 Screen mode NORMAL NORMAL H BLK 2 to 3 mm H BLK WIDTH H BLK PHASE Fig. 1-7 V BLK TOP V BLK V BLK BOTTOM Fig. 1-8 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2. Increase the brightness by adjusting the BRIGHT control so that blanking becomes visible on screen. Note: The following adjustment menus are located in the directory under the DEFLECTION menu of the MAINTENANCE menu. V BLK TOP V BLK BOTTOM V SIZE V CENT . V Blanking Adjustment 1. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 2. Press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 3. Press the SHIFT button to OFF. [The LED (orange) on top of the button turns off.] 4. Press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns on.] 5. Adjust the V SIZE data so that the 5% over-scan is obtained. 6. Take note of the present V CENT data. After noting present V CENT data, adjust V CENT so that the top of the raster becomes visible. 7. Adjust the V BLK TOP data so that the vertical blanking on top of the screen is positioned as closest as possible to the signal display area. 8. Adjust V CENT so that the bottom of the raster becomes visible. 9. Adjust the V BLK BOTTOM data so that the vertical blanking on bottom of the screen is positioned as closest as possible to the signal display area. 10. Return the V CENT data to the original data. 3-7 [Linearity Adjustment] . Linearity Adjustment (1) 1. Connect the 1080/60i (1125) cross-hatch signal to the ANALOG Y/G input connector. 2. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 3. Press the 16:9 ON button [to turn on the LED (orange)] to select the 16:9 mode. 4. Press the SHIFT button to OFF. [The LED (orange) on top of the button turns off.] 5. Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns off.] 6. Check that the picture is not slanted, that there are no top and bottom PIN distortion and horizontal trapezoidal distortion. Slanted picture: Adjust inclination of the DY. Horizontal PIN distortion: Adjust upper and lower neck twist of the DY. Horizontal trapezoidal distortion: Adjust TLV adjustment control of the DY. (Be careful that the TLV adjustment can deteriorate the convergence.) . Linearity Adjustment (2) Note 1) Connect the monoscope signal or the crosshatch signal having the following signal formats as shown in the table below, to the ANALOG Y/ G input connector. Perform the linearity adjustment (2) in the respective screen modes using the respective signal formats. 60 Hz system MODE MODE1 MODE2 MODE3 MODE4 MODE5 MODE6 MODE7 MODE8 MODE9 MODE10 MODE11 MODE12 MODE13 MODE14 Signal format 1080/60i (1125) 1035/60i (1125) 720/60p 480/60p (525) 16 : 9 16 : 9 16 : 9 16 : 9 4:3 480/60i (525) 16 : 9 4:3 Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN 50 Hz system MODE MODE15 MODE16 MODE17 MODE18 MODE19 MODE20 MODE21 MODE22 MODE23 MODE24 MODE25 MODE26 MODE27 MODE28 3-8 Signal format 1080/48i (1125) 1080/50i (1125) 720/50p 575/50P (625) 16 : 9 16 : 9 16 : 9 16 : 9 4:3 575/50i (625) 16 : 9 4:3 Screen mode NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN NORMAL UNDER SCAN BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Note 2) The following adjustment menus are located in the directory under the DEFLECTION menu of the MAINTENANCE menu. H SIZE H CENTER H KEY BAL H KEY H PIN BAL H PIN H COR S H COR PIN H PIN V SIZE V CENTER V LIN AMP V LIN BAL 1. Connect the monoscope signal to the ANALOG Y/G input connector. 2. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 3. To adjust the 4:3 mode of adjustment, press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 4. Press the SHIFT button to OFF. [The LED (orange) on top of the button turns off.] 5. To select the NORMAL mode of adjustment, press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns off.] To select the UNDER SCAN mode of adjustment, press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns on.] 6. Adjust the H CENTER data so that the horizontal center of the picture comes to the horizontal center of the screen. 7. Adjust the V CENTER data so that the vertical center of the picture comes to the vertical center of the screen. 8. Connect the cross-hatch signal to the ANALOG Y/G input connector. 9. Adjust the respective V SIZE, V LIN BAL, V LIN AMP and H SIZE data so that the optimum picture is obtained as shown in Fig. 1-9. Note: Do not adjust the V SIZE data when adjusting the MODEs 9, 13, 23 and 27. 10. Adjust the horizontal trapezoidal distortion and horizontal PIN distortion on both sides of picture using the H KEY BAL, H KEY, H PIN BAL and H PIN data respectively as shown in Fig. 1-10. 11. Adjust the corner “S” distortion and the corner PIN distortion on both sides of picture using the H CORS and H COR PIN data respectively as shown in Fig. 111. 12. Repeat the above-described steps of the linearity adjustment(2) until the optimum horizontal linearity and vertical linearity are obtained. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A V LIN BAL V LIN AMP Fig. 1-9 H KEY BAL H KEY H PIN BAL H PIN Fig. 1-10 H COR S H COR PIN Fig. 1-11 3-9 [Convergence Adjustment] . Preparation 1. Connect the 480/60p cross-hatch signal to the ANALOG Y/G input connector. 2. Press the SHIFT button to ON. [The LED (orange) on top of the button turns on.] 3. Press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 4. Press the SHIFT button to set the SHIFT OFF. [The LED (orange) on top of the button turns off.] 5. Press the UNDER SCAN button ( ) to its OFF position to select the NORMAL mode of adjustment. [The green LED turns off.] [Static Convergence Adjustment] . Horizontal Static Convergence Adjustment 1. Adjust RV701 (H. STAT) on the C board so that the red dots and the green dots are correctly converged. 2. When the blue dot is mis-converged with respect to the red and green dots, implement the HMC (horizontal misconvergence) correction by adjusting the 4-pole magnet and the 6-pole magnet of the DY. . Vertical Static Convergence Adjustment 1. Implement the VMC (vertical misconvergence) correction by adjusting the 4-pole magnet and the 6pole magnet of the DY. Purity 6-pole 4-pole R G B R G B Fig. 1-13 Fig. 1-12 Fig. 1-14 3-10 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A [Dynamic Convergence Adjustment] 1. Minimize the vertical misconvergence in the left-most end of the center of a screen and in the right-most end of the center of a screen by adjusting the DY correction reactor XCV as shown in Fig. 1-15. 2. Minimize the vertical misconvergence in the top of a screen and in the bottom of a screen by adjusting the DY correction reactor YCH as shown in Fig. 1-15. 3. Minimize the vertical misconvergence in the top of a screen and in the bottom of a screen by adjusting the DY correction reactor TLV as shown in Fig. 1-15. 4. Minimize the vertical misconvergence in the left-most end of the center of a screen and in the right-most end of the center of a screen by adjusting the DY correction reactor TLH as shown in Fig. 1-15. XCV YCH Pedestal G B B [G2 Adjustment] 1. Connect the 480/60i entire black signal to the ANALOG Y/G input connector. 2. Connect an oscilloscope probe one after another to the C board R-cathode (TP701), G-cathode (TP702) then B-cathode (TP703) to measure the DC voltage at their respective pedestal portion. 3. Connect an oscilloscope to the cathode whose DC voltage of the respective pedestal portion has the highest DC voltage. 4. Adjust RV702 on the C board so that the DC voltage of the respective pedestal portion is 125 ± 3 V. R R G R 125±3(VDC) B R TLV R G B B 0(VDC) TLH Fig. 1-16 B G R R GB B GR Fig. 1-15 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3-11 [White Balance Adjustment] 1. Outline of the white balance adjustment and calibration of the color analyzer that is used for the white balance adjustment are described first. 1,1 The parameter that converts the RGB drive voltage of a CRT to the chromaticity coordinate is acquired. This monitor has the copy function of the color temperature data between two or more monitors. However, the CRT drive voltage are unique in every monitor because it is different depending on each CRT. Therefore, the same color temperature cannot be obtained in multiple monitors even though the same drive voltage is given to them. It means that the data that is used to copy the color temperature, must be the xyY chromaticity coordinate or similar data that does not depend on each CRT, unlike the CRT drive that depends on each CRT. When the D93 MANUAL adjustment is implemented using the MAINTENANCE/SYSTEM/COLOR TEMP menu of the SYSTEM CONFIG menu, the parameter that converts the CRT drive voltage to the chromaticity coordinate is created while the adjustment is implemented. This parameter is used when copying the color temperature data to other monitors as shown. CRT drive voltage CRT drive voltage Chromaticity coordinate Chromaticity coordinate Data transmission Fig. 1-17 1.2 D65 color temperature adjustment 1.3 Copying the color temperature data to the STD color temperature, COLOR1 color temperature and COLOR2 color temperature. . On calibration of the color analyzer When color temperature of any monitor is measured by two or more color analyzers, these color analyzers show different measurement values even though the object of measurement is the same. Also the measurement value of color analyzer changes as time elapses. Therefore, any color analyzer must be calibrated so that it shows the correct measurement value of the following chromaticity coordinate before using the analyzer. D65 D93 3-12 x 0.313 0.313 0.283 0.283 y 0.329 0.329 0.297 0.297 y (cd/m2) 2.7 120 2.7 120 2. Preparation for Adjustment 2.1 Connect the 480/60i (525) WINDOW signal to the ANALOG Y/G input connector. 2.2 Connect the RS-232C connector of a color analyzer CA-100 with the OPTION connector of a monitor using the cable that is shown by section “3-1. Set-Up Adjustment When CRT is Replaced - Required tools and measuring instruments, item 8”. 2.3 Set up the CA-100 as described below. Attach the measurement probe of the CA-100 to the center of the CRT screen. Display mode xyY mode Baud rate 9600 3. White Balance Adjustment 3.1 White Balance Adjustment (1) 1. Press the SHIFT ON button [to turn on the LED (orange) on top of the SHIFT button]. Press the 16:9 ON button [to turn on the LED (orange)] to select the 16:9 mode. 2. Press the MONO ON button to select the B/W mode. [The green LED turns on.] 3. Select MAINTENANCE menu of the SYSTEM CONFIG menu. 4. Select VIDEO menu of the MAINTENANCE menu. 5. Take note of the SUB CONTRAST data. Then set 100 to the SUB CONTRAST data. 6. Select SYSTEM/COLOR TEMP menu of the MAINTENANCE menu. 7. Select D93 of the SYSTEM/COLOR TEMP menu. Then cover the entire CRT screen surface with a black blind cloth. Select the MANUAL adjustment item and adjust the white balance until the following value is obtained. x = 0.283 y = 0.297 8. Select D65 of the SYSTEM/COLOR TEMP menu. Then cover the entire CRT screen surface with a thick black blind cloth. Select the MANUAL adjustment item and adjust the white balance until the following value is obtained. x = 0.313 y = 0.329 9. Select the SYSTEM/COLOR TEMP/COPY/OTHER VALUE menu. 10. After selecting the STD item of the COLOR TEMP menu, select D93. Copy the D93 color temperature data to STD. 11. After selecting the COLOR1 item of the COLOR TEMP menu, select D65. Copy the D65 color temperature data to COLOR1. 12. After selecting the COLOR2 item of the COLOR TEMP menu, select D93. Copy the D93 color temperature data to COLOR2. 13. Select VIDEO menu of the MAINTENANCE menu. 14. Return the SUB CONTRAST data to the original data. 15. Press the MONO button to the OFF position to cancel the B/W mode. [The green LED turns off.] BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3.2 Sub Contrast Adjustment 1. Connect the 480/60i (525) 100 IRE WINDOW signal to the ANALOG Y/G input connector. 2. Attach the luminance meter to the center of the CRT screen. 3. Select STD using the COLOR TEMP menu of the INPUT CONFIG menu. 4. Select MAINTENANCE menu of the SYSTEM CONFIG menu. 5. Select SUB CONTRAST menu of the VIDEO menu. 6. Press the SHIFT ON button [to turn on the LED (orange) on top of the SHIFT button]. Press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 7. Press the SHIFT OFF button [to turn off the LED (orange) on top of the SHIFT button]. Press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns off.] 8. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 9. Press the SHIFT ON button [to turn on the LED (orange) on top of the SHIFT button]. Press the 16:9 ON button [to turn on the LED (orange)] to select the 16:9 mode. 10. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 11. Press the SHIFT OFF button [to turn off the LED (orange) on top of the SHIFT button]. Press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns off.] 12. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 13. Press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns off.] 14. Press the SHIFT ON button [to turn on the LED (orange) on top of the SHIFT button]. Press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 15. Connect the 1080/60i 100 IRE WINDOW signal to the ANALOG Y/G input connector. 16. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 17. Press the SHIFT OFF button [to turn off the LED (orange) on top of the SHIFT button]. Press the UNDER SCAN button ( ) to its ON position to select the under scan mode. [The green LED turns off.] 18. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 19. Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns on.] 20. Connect the 480/60p (525P) 100 IRE WINDOW signal to the ANALOG Y/G input connector. 21. Press the SHIFT ON button [to turn on the LED (orange) on top of the SHIFT button]. Press the 16:9 OFF button [to turn off the LED (orange)] to select the 4:3 mode. 22. Press the SHIFT OFF button [to turn off the LED (orange) on top of the SHIFT button]. Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns on.] 23. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 24. Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns on.] 25. Adjust SUB CONTRAST so that luminance becomes 120 cd/m2. 26. Press the UNDER SCAN button ( ) to its OFF position to select the normal mode. [The green LED turns on.] 3.3 White Balance Adjustment (2) 1. Connect the 480/60i (525) 20 IRE WINDOW color difference signal to the ANALOG Y/G input connector. 2. Select STD using the COLOR TEMP menu of the INPUT CONFIG menu. 3. Select MAINTENANCE menu of the SYSTEM CONFIG menu. 4. Select the VIDEO menu. 5. Increase the CHROMA control to its maximum. 6. Adjust white balance by adjusting the PR/R BLACK and PB/B BLACK menus of the VIDEO menu. x = 0.283 y = 0.297 3-13 3.4 White Balance Adjustment (3) 1. Connect the 1080/60i (1125) 20 IRE WINDOW color difference signal to the ANALOG Y/G input connector. 2. Select STD using the COLOR TEMP menu of the INPUT CONFIG menu. 3. Select MAINTENANCE menu of the SYSTEM CONFIG menu. 4. Select the VIDEO menu. 5. Increase the CHROMA control to its maximum. 6. Adjust white balance by adjusting the PR/R BLACK and PB/B BLACK menus of the VIDEO menu. x = 0.283 y = 0.297 3.5 1. 2. 3. 4. 5. 6. 7. 8. 9. White Balance Adjustment (4) Turn off the main POWER switch. Insert the BKM-142HD into the SLOT 2. Connect the HD-SDI 20 IRE WINDOW signal to the BKM-142HD. Turn on the main POWER switch. Select HD-SDI using the FORMAT menu of the INPUT CONFIG menu. Select MAINTENANCE menu of the SYSTEM CONFIG menu. Select the VIDEO menu. Increase the CHROMA control to its maximum. Adjust white balance by adjusting the PR/R BLACK and PB/B BLACK menus of the VIDEO menu. x = 0.283 y = 0.297 3-14 3.6 White Balance Adjustment (5) 1. Turn off the main POWER switch. 2. Insert the BKM-120D into the SLOT 2. 3. Connect the D1-SDI 20 IRE WINDOW signal to the BKM-120D. 4. Turn on the main POWER switch. 5. Select D1-SDI using the FORMAT menu of the INPUT CONFIG menu. 6. Select MAINTENANCE menu of the SYSTEM CONFIG menu. 7. Select the VIDEO menu. 8. Increase the CHROMA control to its maximum. 9. Adjust white balance by adjusting the PR/R BLACK and PB/B BLACK menus of the VIDEO menu. x = 0.283 y = 0.297 3.7 1. 2. 3. 4. 5. 6. 7. 8. 9. White Balance Adjustment (6) Turn off the main POWER switch. Insert the BKM-127W into the SLOT 2. Connect the NTSC 20 IRE WINDOW signal to the BKM-127W. Turn on the main POWER switch. Select NTSC, PAL using the FORMAT menu of the INPUT CONFIG menu. Select MAINTENANCE menu of the SYSTEM CONFIG menu. Select the VIDEO menu. Increase the CHROMA control to its maximum. Adjust white balance by adjusting the PR/R BLACK and PB/B BLACK menus of the VIDEO menu. x = 0.283 y = 0.297 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Section 4 Safety Related Adjustments This section describes the adjustment procedure that is required when the safety related parts are replaced. [Preparation] . Required tools and measuring equipment 1. Signal generator YPB/YPR signal generator . 1080/60i (1125) : SMPTE 274M standard . 480/60i (525) : ITU601 (Refer to page 1-29) 2. Electrostatic voltmeter: Singer ESH-27X or ESH-23X or equivalent 3. Digital voltmeter 4. 200 kΩ variable resistor 5. 20 kΩ variable resistor 6. Ammeter . Set the INPUT CONFIGURATION menu Set the INPUT CONFIGURATION menu of the SETUP menu as shown below unless otherwise specified. FORMAT ................................ YPBPR SLOT NO ................................ 1 INPUT NO .............................. 1 SYNC MODE ......................... INT APEARTURE VALUE .......... 100 CHANNEL NAME ................ PROG COLOR TEMP ....................... STD H PHASE ................................ 000 MARKER PHASE .................. 000 MARKER WIDTH ................. 000 SLOT No. 1 Y/G terminal PB/B terminal PR/R terminal SYNC terminal Component signal generator BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 4-1 +B (135 V) Voltage Check 1. Connect a digital voltmeter across C645 on the G board. 2. Turn on the main power. 3. Connect the 1080/60i 100 IRE signal (see note) to input connector. Note: 1125 (1080) 100 IRE signal 4. Push the BRIGHTNESS and CONTRAST buttons to their MANUAL positions (to turn the green LEDs on the buttons.) 5. Set the BRIGHTNESS and CONTRAST buttons to their MAX positions. 6. Check that the following DC voltage appears. 135.0 ± 0.8 V 7. Turn off the main power. 8. Disconnect the digital voltmeter. [Connection] G board (Side B) 1 2 3 4 5 6 7 Digital voltmeter A B C D E Digital voltmeter F G Ammeter C645 20kΩ H High Voltage Regulator Check I When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to perform the following checks. D512 J K GND 200kΩ R1522 IC523-Pin 2 G board ....... IC515, IC519, IC520, T502, R1509, R1514, R1576, R1577, R592, R593, R599 1. Turn off the main power. 2. Connect an electrostatic voltmeter to the anode cap of CRT tube. . Electrostatic voltmeter: It must have already been calibrated to have the input impedance of 2 x 109 Ω or more. Singer ESH-27X or ESH-23X or equivalent 3. Turn on the main power. 4. Connect the 1080/60i monoscope signal (see note) to input connector. Note: 1125 (1080) monoscope signal 5. Push the BRIGHTNESS and CONTRAST buttons to their MANUAL positions (to turn the green LEDs on the buttons.) 6. Set the BRIGHTNESS and CONTRAST buttons to their mechanical center positions. 7. Check that the following high voltage appears. 22.5 ± 1.0 kV 8. Turn off the main power. 9. Disconnect the electrostatic voltmeter. 4-2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A High Voltage Hold-Down Check Beam Current Protector Check When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to perform the following checks. When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to perform the following checks. G board ...... IC514, IC507, IC523, Q520, D506, D513, D535, T502, R553, R560, R561, R569, R575, R597, R1566, R512 1. Turn off the main power. 2. Connect a digital voltmeter between D513 cathode and GND of G board. 3. Connect a 200 kΩ variable resistor between IC523 pin-2 and GND of the G board. [Adjust the 200 kΩ variable resistor to its maximum resistance value.] 5. Connect the 480/60i entire black signal (see note) to input connector. Note: NTSC entire black signal 6. Push the BRIGHTNESS and CONTRAST buttons to their MANUAL positions (to turn the green LEDs on the buttons.) 7. Set the BRIGHTNESS and CONTRAST buttons to their MIN positions. 8. Confirm that the raster disappears from the CRT screen when the DC voltage at D513 cathode reaches the following voltage as the 200 kΩ variable resistor is turned to decrease its resistance value gradually. 25.5 ± 1.0 V 9. Turn off the main power. 10. Remove the 200 kΩ variable resistor that is connected to IC523 pin-2. 11. Turn on the main power. 12. Confirm that the DC voltage at D513 cathode is as follows. 20.0 ± 1.5 V 13. Connect the 480/60i entire white signal to input connector. 14. Set the BRIGHTNESS and CONTRAST buttons to their MAXIMUM positions. 15. Confirm that the DC voltage at TP505 is as follows. 22.0 ± 2.0 V 16. Disconnect the digital voltmeter. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G board ....... IC507, IC517, IC523, Q520, D507, D535, T502, R1516, R1517, R1518, R1521, R1522, R1523, R1566, R1569, R512, R562, R576, R578, R579, R580, R586 1. Turn off the main power. 2. Connect a DC ammeter and a 20 kΩ variable resistor in series between the junction point of R1522 and R1523, and GND on the G board [The junction point of R1522 and R1523 is the positive (+) side. Adjust the 20 kΩ variable resistor to its maximum resistance beforehand.] 3. Turn on the main power. 4. Connect the 480/60i entire black signal (see note) to input connector. Note: NTSC entire black signal 5. Push the BRIGHTNESS and CONTRAST buttons to their MANUAL positions (to turn the green LEDs on the buttons.) 6. Set the BRIGHTNESS and CONTRAST buttons to their mechanical center positions. 7. Confirm that the raster disappears from the CRT screen when the DC ammeter reaches the following value as the 20 kΩ variable resistor is turned to decrease its resistance value gradually. 1600 µA 8. Turn off the main power. 9. Remove a 20 kΩ variable resistor and a DC ammeter. 4-3 4-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Section 5 Circuit Adjustments 5-1. B Board Adjustments This section describes the following adjustments that are required when the parts are replaced or maintenance is performed in the B board. 1. RGB signal adjustment 2. 15k YPBPR SMPTE (709) signal adjustment 3. 15k YPBPR SMPTE (601) signal adjustment 4. 15k YPBPR BETACAM SETUP 0 (601) signal adjustment 5. 15k YPBPR BETACAM SETUP 7.5 (601) signal adjustment 6. 33k YPBPR SMPTE (709) Signal Adjustment Control Settings . Set the INPUT CONFIGURATION menu of the SETUP menu as shown below. FRMAT ............... YPBPR SLOT NOT ......... 1 INPUT NOT ........ 1 . Set “128” to the CHROMA data using the CHROMA control knob. . Perform the following operaion using the SYSTEM CONFIG menu. Select the B BOARD using the RE-LOAD FACTORY DATA of the SYSTEM menu. Equipment Required Name Main Specifications Model Name Signal generator 15 kHz/60 Hz RGB VG-854 or equivalent 15 kHz/60 Hz YPBPR SMPTE (709) 15 kHz/60 Hz YPBPR SMPTE (601) 15 kHz/60 Hz YPBPR BETACAM SETUP 7.5 (601) 33 kHz/60 Hz YPBPR SMPTE (709) Oscilloscope Frequency: DC to 150 MHz or more TEKTORONIX 2445A Dual trace or equivalent Connection (1) Y/G terminal PB/B terminal PR/R terminal SYNC terminal SLOT No. 1 Component signal generator BKM-129X BVM-D14H1U/D14H5U/D114H1E/D14H5E/D14H1A/D14H5A BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5-1 Connection (2) A B C D TP1302 1 TP302 TP303 TP1301 TP301 TP1300 2 TP304 3 4 5 B board -side A- Adjustment Procedure 1. RGB Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Adjust the GREEN waveforms to have Use the adjustment menu Y/G BLACK . Input the 15 kHz/60 Hz the same amplitude at TP302. (40H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the RGB 100% color bar signal. . Use the FORMAT item of the MAINTENANCE menu. INPUT CONFIG menu to select RGB. . Connect an oscilloscope to TP302. Make flat Step 2 Make flat the pedestal portion of the Use the adjustment menu PB/B BLACK . Connect an oscilloscope to TP303. BLUE waveform at TP303. (30H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the MAINTENANCE menu. Make flat Step 3 Make flat the pedestal portion of the Use the adjustment menu PR/R BLACK . Connect an oscilloscope to TP304. RED waveform at TP304. (20H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the MAINTENANCE menu. Make flat 5-2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 2. 15k YPBPR SMPTE (709) Signal Adjustment 2-1. BLACK Level Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the pedestal portion of the Use the adjustment menu Y/G BLACK . Input the 15 kHz/60 Hz YPBPR Y-signal waveform at TP302. (41H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the SMPTE (709) 100% color bar signal. . Use the FORMAT item of the INPUT MAINTENANCE menu. CONFIG menu to select YPBPR SMPTE. Set 709 for YPBPR MATRIX. Make flat . Connect an oscilloscope to TP302. Step 2 Make flat the pedestal portion of the . Connect an oscilloscope to TP303. PB waveform at TP303. (32H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the Make flat Use the adjustment menu PB/B BLACK MAINTENANCE menu. Step 3 Make flat the pedestal portion of the Use the adjustment menu PR/R BLACK . Connect an oscilloscope to TP304. PR waveform at TP304. (22H) that is located under the directory Level difference: 0 ± 10 mV of the VIDEO menu of the Make flat MAINTENANCE menu. 2-2. CHROMA Leak Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the PB waveform at TP303. Use the adjustment menu CHROMA PB . Input the 15 kHz/60 Hz YPBPR Level difference: 0 ± 20 mV (11H) that is located under the directory SMPTE (709) 100% color bar signal. of the VIDEO menu of the . Use the FORMAT item of the INPUT MAINTENANCE menu. CONFIG menu to select YPBPR SMPTE. Set 709 for YPBPR MATRIX. Make the signal amplitude as flat as possible. . Use the CHROMA knob to set “0” to the CHROMA data. . Connect an oscilloscope to TP303. Step 2 Make flat the PR waveform at TP304. Use the adjustment menu CHROMA PR . Connect an oscilloscope to TP304. Level difference: 0 ± 20 mV (10H) that is located under the directory of the VIDEO menu of the Make the signal amplitude as flat as possible. MAINTENANCE menu. Step 3 . Set “128” to the CHROMA data using the CHROMA control knob. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5-3 2-3. MATRIX Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL . Input the 15 kHz/60 Hz YPBPR 560 ± 20 mVp-p (50H) that is located under the directory SMPTE (709) 100% color bar signal. of the VIDEO menu of the . Use the FORMAT item of the INPUT CONFIG menu to select YPBPR SMPTE. MAINTENANCE menu. 560±20mVp-p Set 709 for YPBPR MATRIX. . Connect an oscilloscope to TP1301. Step 2 Adjust the RED waveforms to have Use the adjustment menu PR LEVEL . Connect an oscilloscope to TP1300. the same amplitude at TP1300. (60H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 3 Adjust the BLUE waveforms to have Use the adjustment menu PB LEVEL . Connect an oscilloscope to TP1302. the same amplitude at TP1302. (80H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 4 Make flat the GREEN waveform at TP1301 Use the adjustment menu G-Y/R (70H) . Connect an oscilloscope to TP1301. Level difference: 0 ± 20 mV and G-Y/B (90H) that is located under the directory of the VIDEO menu of the MAINTENANCE menu. G-Y/R variable G-Y/B variable Make the portions flat 5-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 3. 15k YPBPR SMPTE (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL . Input the 15 kHz/60 Hz YPBPR 560 ± 20 mVp-p (51H) that is located under the directory SMPTE (601) 100% color bar signal. of the VIDEO menu of the . Use the FORMAT item of the INPUT MAINTENANCE menu. CONFIG menu to select YPBPR SMPTE. 560±20mVp-p Set 601 for YPBPR MATRIX. . Connect an oscilloscope to TP1301. Step 2 Adjust the RED waveforms to have Use the adjustment menu PR LEVEL . Connect an oscilloscope to TP1300. the same amplitude at TP1300. (62H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 3 Adjust the BLUE waveforms to have Use the adjustment menu PB LEVEL . Connect an oscilloscope to TP1302 the same amplitude at TP1302. (82H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 4 Make flat the GREEN waveform at TP1301 : Use the adjustment menu G-Y/R (71H) . Connect an oscilloscope to TP1301. Level difference: 0 ± 20 mV and G-Y/B (91H) that is located under the directory of the VIDEO menu of the G-Y/R variable MAINTENANCE menu. G-Y/B variable Make the portions flat BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5-5 4. 15k YPBPR BETACAM SETUP 0 (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL . Input the 15 kHz/60 Hz YPBPR BETACAM 560 ± 20 mVp-p (52H) that is located under the directory SETUP 0 (601) 75% color bar signal. of the VIDEO menu of the . Use the FORMAT item of the INPUT MAINTENANCE menu. CONFIG menu to select YPBPR BETA 0. 560±20mVp-p . Connect an oscilloscope to TP1301. Step 2 Adjust the RED waveforms to have Use the adjustment menu PR LEVEL . Connect an oscilloscope to TP1300. the same amplitude at TP1300. (64H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 3 Adjust the BLUE waveforms to have Use the adjustment menu PB LEVEL . Connect an oscilloscope to TP1302. the same amplitude at TP1302. (84H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude. Step 4 Make flat the GREEN waveform at TP1301. Use the adjustment menu G-Y/R (72H) . Connect an oscilloscope to TP1301. Amplitude between YELLOW and pedestal: and G-Y/B (92H) that is located under the 420 ± 20 mVp-p directory of the VIDEO menu of the Make flat the waveform: Level difference: MAINTENANCE menu. 0 ± 20 mV Yellow 420±20mVp-p G-Y/B variable Make the portions flat G-Y/R variable Pedestal 5-6 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5. 15k YPBPR BETACAM SETUP 7.5 (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the pedestal portion of the Use the adjustment menu Y/G BLACK . Input the 15 kHz/60 Hz YPBPR Y-signal waveform at TP302. (42H) that is located under the directory BETACAM SETUP 7.5 (601) Level difference: 0 ± 10 mV of the VIDEO menu of the 75% color bar signal. MAINTENANCE menu. . Use the FORMAT item of the INPUT CONFIG menu to select YPBPR BETA 7.5. Adjust for the same amplitude . Connect an oscilloscope to TP302. Step 2 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL . Connect an oscilloscope to TP1301. 560 ± 20 mVp-p (53H) that is located under the directory of the VIDEO menu of the MAINTENANCE menu. 560±20mVp-p Step 3 Adjust the RED waveforms to have Use the adjustment menu PR LEVEL . Connect an oscilloscope to TP1300. the same amplitude at TP1300. (65H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 4 Adjust the BLUE waveforms to have Use the adjustment menu PB LEVEL . Connect an oscilloscope to TP1302. the same amplitude at TP1302. (85H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude Step 5 Make flat the GREEN waveform at TP1301. Use the adjustment menu G-Y/R (73H) . Connect an oscilloscope to TP1301. Amplitude between YELLOW and pedestal: and G-Y/B (93H) that is located under the 420 ± 20 mVp-p directory of the VIDEO menu of the Make flat the waveform: MAINTENANCE menu. Level difference: 0 ± 20 mV Yellow 420±20mVp-p G-Y/B variable Make the portions flat. G-Y/R variable Pedestal BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5-7 6. 33k YPBPR SMPTE (709) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the PB waveform at TP303. Use the adjustment menu PB/B BLACK . Input the 33 kHz/60 Hz YPBPR Level difference: 0 ± 10 mV (33H) that is located under the directory SMPTE (709) 100% color bar signal. . Use the FORMAT item of the INPUT Make the portions flat of the VIDEO menu of the MAINTENANCE menu. CONFIG menu to select YPBPR SMPTE. . Connect an oscilloscope to TP303. Step 2 Make flat the PR waveform at TP304. Use the adjustment menu PR/R BLACK . Connect an oscilloscope to TP304. Level difference: 0 ± 10 mV (23H) that is located under the directory of the VIDEO menu of the Make the portions flat Step 3 Check amplitude of the GREEN waveform . Connect an oscilloscope to TP1301. at TP1301: 560 ± 20 mVp-p MAINTENANCE menu. 560±20mVp-p Step 4 Adjust the RED waveforms to have Use the adjustment menu PR LEVEL . Connect an oscilloscope to TP1300. the same amplitude at TP1300. (61H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude. Step 5 Adjust the BLUE waveforms to have Use the adjustment menu PB LEVEL . Connect an oscilloscope to TP1302. the same amplitude at TP1302. (81H) that is located under the directory Level difference: 0 ± 20 mV of the VIDEO menu of the MAINTENANCE menu. Adjust for the same amplitude. 5-8 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Section 6 Circuit Descriptions This section describes the circuit operations of the following boards used in the BVM-D14H1J/D14H5J. 6-1. 6-2. 6-3. 6-4. 6-5. 6-6. G board G1 board B board C board MA board MB board 6-1. G Board Power Supply Circuit Power supply of this monitor consists of the following two switching regulators. 1. The power factor improvement regulator that is used to comply with the power supply high frequency harmonics regulations. 2. The main regulator that supplies the power to the signal system, the deflection circuit and high voltage circuit. 1. Power Factor Improvement Circuit The power factor improvement block The power factor improvement circuit of this monitor uses the active filter IC module (IC601) of the current-threshold type boost-chopper system to comply with the power supply high frequency harmonics regulations. The power factor improvement circuit consists of IC601, T603 and C615. IC601 is a module IC in which the control IC, the switching FET, the boost diode and input/output voltage detectors are built in. Basic operation of the power factor improvement block is as follows. When the POWER signal (IC508 pin-1 output) goes “LOW” and the Vcc power is supplied to IC601, the FET inside the module IC601 is turned on and an electric current starts to flow in the primary winding of T603 and the FET. This current increases with the slope of Vin (rms)/L where L is the primary side inductance of T603. This FET current is monitored by the source current detection resistor that is connected between pin-4 and pin7 of IC601. When this FET current reaches the set value that is specified by the multiplier inside the control IC, the FET is turned off. Then an electric current flows through the boost diode where the current decreases with the slope of -(Vd - Vin (rms))/L. When this current reaches 0, the FET is turned on. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A The current-threshold operation is thus realized by the above described circuit operations. (Vd: Voltage across C615. Vin: Input voltage to power supply) In other words, the circuit operations that are described, are performed as one-operation-cycle all the time while the power is on. When you observe the circuit operations as described above, during only the half-wave period of commercial power line frequency, you will notice that ON/ OFF timing of the FET is controlled by the control IC so that the envelope of the peak values of the choke current is proportional to the half-wave of the sine waveform of the power line frequency. As the result of this control, waveform of the input voltage and that of the output voltage become similar so that the power factor is improved. At the same time, the voltage Vd across C615 becomes higher than the peak value of the input voltage to the power circuit. The voltage Vd is set to about 380 V regardless of the input voltage to the power circuit. This circuit does not operate during the standby mode. When this circuit is not operating, the voltage Vd becomes almost equal to the peak value of the input voltage to the power supply circuit. 2. Main Regulator The separately excited current composite resonance system is used for the main regulator. The main regulator consists mainly of IC602, IC610, T605, C629, C631 and the secondary side rectifier circuit of T605. IC602 is a multiple chip module in which the four chips of the control block, the FET drive block and the switching FET block (high side and low side) are connected by bonding wire inside the IC. IC210 has the following circuit configuration. A half-bridge rectifier is constructed by the two FET switches, the two capacitors C629 and C631, and the transformer T605 for the input voltage Vd. The secondary side of the transformer has the half wave rectifiers and full wave rectifiers for each output lines. IC602 receives the control signal from IC610 that performs the constant voltage control over the +135 V line through the isolator PH603. The control signal changes the oscillating frequency of IC602 so that the constant voltage control is realized. The secondary side of T605 generates not only +135 V but also +160 V, +15 V, _15 V, +6 V, _6 V powers and the heater voltage that are required by the respective circuits. The +15 V, _15 V, +6 V, _6 V powers are regulated to +12 V, _12 V, +5 V, _5 V powers by the three-terminal regulators respectively so that these powers are supplied to each circuit board. 6-1 3. Over-Voltage Protection and Over-Current Protection Circuit The +135 V voltage line of the main power supply has the over-voltage protection circuit and the over-current protection circuit that protect the power supply circuit and the loads when an abnormality occurs in the respective loads and in the voltage feedback system. When an over-current occurs, the latch circuit consisting of Q616 and Q617 is turned on so that the VCC power to IC601 and IC602 is turned off through the isolator PH604 to stop operation of the main power supply circuit. This protection circuit is released when the input power to the main power supply circuit is turned off once or when the standby mode is selected. Deflection and High Voltage Circuit 1. Sync Signal and Deflection Signal Processing Circuit The horizontal and vertical sync signals that are input from CN501 (pins-1/-2) are sent to the H/V DELAY timing circuit consisting of IC510, IC522, IC509 and IC526. The H/V DELAY timing circuit outputs the sync signals that have the same phase as those of the input signal during normal operation. However, during the H/V DELAY mode, it outputs the delayed sync signals to which delay is given by IC509 and IC510. The output sync signals are processed of the waveforms by IC503 and are sent to the deflection signal processor IC507. The deflection signal processor IC507 outputs the various signals that are required for deflection, such as horizontal drive circuit, parabola signal for dynamic focusing, parabola signal for picture distortion correction, vertical drive signal and H/V blanking signals. The output signals are controlled directly by the microprocessor in the MA board through I2C bus. The horizontal free-running frequency is set for about 18 kHz. The pull-in range of the input signal frequency is from 15 kHz to 45 kHz. The deflection signal processor IC507 has the built-in protector for X-ray protection. When its pin-15 is raised to 8 V or higher, the X-ray protection circuit starts working to stop the horizontal and vertical outputs. The X-ray protector circuit can be reset by turning off the main power once then back on, or by entering the standby mode. There can be a case that the monitor receives the nonstandard TV signal such as the output signal from VTR. In order to reduce the skew effect on screen caused by irregular timing of the input sync signal, the PLL circuit inside the IC507 is stopped during the vertical blanking period. 6-2 This function is effective when the horizontal frequency of the input signal is 15 kHz (NTSC and PAL). Because this circuit produces an ill effect when the standard TV signal is input, use or not-use of this circuit can be selected from the on-screen menu. 2. PWM Control Circuit for +B Power Voltages for Horizontal Deflection and of High Voltage The PWM control circuit for +B power voltage consists of IC515 and its peripheral circuit. The horizontal drive signal that is output from IC507 pin-21 is used as the PWM trigger signal. The PWM control for horizontal deflection system is performed by inputting the deflection distortion correction signal that is output from IC507 pin-31 to which the H. size control DC voltage super-imposed, to IC515 pin-8. On the other hand, the horizontal signal that is fed back from the horizontal output circuit is inputted to IC515 pin7. These two input signals are compared and the error signal between them, that is the PWM control signal is output from IC515 pin-11. The PWM control output signal is sent to the +B regulator circuit consisting of Q2503 and its peripheral circuit that control the H. size and the deflection distortion correction. The PWM control for the high voltage circuit is performed by inputting the reference signal generated by IC519, to IC515 pin-16 that is compared with the FBT high voltage detected voltage that is input to IC515 pin-17. The error signal between them, that is the PWM control signal is output from IC515 pin-13. The PWM control output signal is sent to the +B regulator circuit consisting of Q514 and its peripheral circuit that control the high voltage to be supplied to CRT. The PWM control signal that is output from IC515 receives the DTC (Dead Time Control) in order to protect the horizontal output circuit and the high voltage output circuit from damage caused by the sharp change of frequency of the input video signal. The DTC circuit works as follows. When frequency of the input sync signal is changed, the unlock signal that is output from IC507 pin37 is sent to IC507 pin-6 as the DTC signal input via the switches Q523 and Q504, so that the PWM is controlled to decrease the +B regulator output voltages to be supplied to the horizontal and high voltage systems. 3. Horizontal Output Circuit The horizontal drive signal that is output form IC507 pin21 is amplified by the horizontal drive circuit consisting of Q2501, Q2502, Q2505 and their peripheral circuit. The horizontal drive signal then drives T2502 (HDT) and Q2508 (H. OUT). The H. pulse is induced by the resonance between the capacitors C2528, C2530, C2531 and theH. winding impedance. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A The H. pulse is voltage-divided, wave-shaped by IC2501 and its peripheral circuit, and is sent to IC507 pin-6, the B board and the MA board. Amplitude of the horizontal deflection current is detected by T2503, Q2513 and their peripheral circuit. The detected amplitude is fed back to the PWM control circuit. Multiple S-shape correction capacitors are prepared, and are selected by Q2514, Q2515, Q2516, Q2517, Q2518 and Q2519. The S-shape correction capacitors are switched at the following three points of horizontal frequencies: Horizontal frequency of 15 kHz, H. frequency in the range of 27 to 33.75 kHz and H. frequency in the range of 37 to 45 kHz. The horizontal linearity correction coils are switched by the relay RY2501 when the H. frequency of 15 kHz is input. The H. centering circuit consists of IC2502, IC2504 and Q2504. The H. center position is controlled by amplifying the H. CENT. DC signal that is supplied from IC508 (D/A) and by super-imposing the DC current to the horizontal deflection current. As to the power supply for IC2504, the secondary winding of T2501 (HOT) is used so that a floating power supply is realized. 4. Vertical Output Circuit The vertical output circuit consists of IC2503 and its peripheral circuit. The vertical output signal is generated by inputting the V. drive signal that is output form IC507 pin-29, to IC2503 pin-1 where it is amplified. The V. center position is controlled by inputting the V. DC signal that is supplied from IC507 pin-28, to IC2503 pin-7. The vertical deflection amplitude and the vertical center position are controlled by IC507. The vertical feedback pulse is generated by wave-shaping the V. flyback pulse with R2570, R2571 and D2520, and by inputting it to IC507 pin-30. 5. High Voltage Output Circuit The HV drive signal that is output from IC515 pin-23 is sent to the high voltage output circuit consisting of Q506, Q507, Q513 (HV. OUT) and their peripheral circuit where the flyback pulse is generated by resonance. The flyback pulse is not only supplied to T502 (FBT) but also rectified, smoothed out by D520 and C578 so that the rectified high voltage is supplied to the C board as the G2 voltage. Amplitude of the high voltage is voltage-divided by the high voltage resistors inside the FBT, and is output from T502 pin-14. The detected output of the high voltage is again voltage-divided by IC520, R1509, R1576 and R1577 so that it is sent to the PWM control signal as the high voltage feedback voltage. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 6. Dynamic Focus Output Circuit The H. focus signal that is output from IC507 pin-17 is amplified by the H. focus amplifier consisting of Q510, Q511, Q512 and the peripheral circuit. The H. focus signal then drives T501 (DFT) where it is amplified to about 500 V and is supplied to T502 pin-17. The H. focus signal interferes with the white balance reference pulse inside the CRT and produces an ill effect. In order to prevent occurrence of the ill effect, the H. focus signal is of a constant voltage is used during the vertical blanking period instead of the H. parabola signal. This switching is performed by IC516, IC524 and the peripheral circuit. The V. focus signal that is output from IC507 pin-32 is amplified by the V. focus amplifier consisting of Q517, Q518 and the peripheral circuit. The V. focus signal is amplified to about 200 V and is supplied to T502 pin-18. 7. H/V Blanking Circuit The H/V blanking circuit consists of IC501, IC527, IC509 and the peripheral circuit. Timing of the H. blanking signal is determined by the timing reference signal. The H. SAW signal that is output from IC507 pin-16 is used as the timing reference signal for the H. blanking. IC501 determines the start position of the H. blanking and IC509 determines the end position of the H. blanking. The V. blanking circuit consists of IC502, IC528, IC510 and the peripheral circuit. The V. SAW signal that is output from IC507 pin-29 is used as the timing reference signal for the V. blanking. IC502 determines the start position of the V. blanking and IC510 determines the end position of the V. blanking. Timing control of the H/V blanking signal is performed using the control voltage that is output from IC512 (DA). 8. Protector Circuit The H/V protector circuit consists of IC523, IC514 and the peripheral circuit. When the voltage that appears at T502 pin-6 (FBT tertiary winding) exceeds the reference voltage that is set by IC514, the internal protector circuit of IC507 is started up through D506. The operating point of the H/ V protector circuit is set at about 27 kV of the high voltage output. The ik protector circuit consists of IC517, IC523 and the peripheral circuit. The ABL current value is detected by R1521, R1522 and R1523. When the detected current value exceeds the reference voltage that is set by IC517, the internal protector circuit of IC507 is started up through D507. The operating point of the ik protector circuit is set at about 1500 µA of the ABL current. 6-3 6-2. G1 Board 6-3. B Board The G1 board is the standby regulator circuit that supplies the standby power (STBY5V) for the control system devices (such as CPU). The standby regulator consists mainly of IC601, IC1602, PH601, T1601 and D1606. IC1601 has the built-in switching FET, the PWM controller and protection circuit. The control terminal of IC1601 receives the control signal from IC1602 that performs the constant voltage control over the STBY5V line through the isolator PH601. The internal FET inside IC1601 is PWM-switched by the control signal so that the STBY5V output from the secondary winding of T1601 is stabilized. 1. Clamp Circuit (1) The signal that is selected by the option board is input to CN301. IC300 (1/3) (analog switch) is turned ON by the Y-CLP-P pulse. As a result, the pedestal voltage of the Y/G signal is sampled-and-held. In IC303, the sampled-and-held voltage and the reference voltage (Y/G BLACK voltage) are compared so that the error voltage is used to control the bias current of the Y/G signal clamp amplifier (Q300 to Q302) so that the pedestal voltage of the Y/G signal is clamped to a fixed voltage. The same clamp operation is performed for the PB/B and PR/R signals but the C-CLP-P pulse is used as the clamp pulse. 1. Over-Voltage Protection and Over-Current Protection Circuit The STBY5V line of the standby power supply have the over-voltage protection circuit that protects the power supply and the loads when an abnormality occurs in the voltage feedback system. When the over-voltage is detected, the “LOW” signal is set to the control terminal of the latch circuit through the isolator PH602 so that the power supply is stopped by the latch circuit consisting of Q606 and Q607. This protection circuit is released wen the input power is turned off that discharges the C615 voltage of the G board. When an over-current is detected in the STBY5V line, the micro-fuse F1603 blows. 2. Matrix Circuit The Y, R-Y and B-Y signals are converted to the R, G and B signals by the matrix circuit in the Y/PB/PR signal is being input. IC306 is the Y-level adjustment amplifier. IC307 and IC308 are the chroma level adjustment amplifier. The Rsignal is generated by adding the Y-signal to the R-Y signal that has passed IC400 (PR gain control amplifier). The Y-signal is generated by adding the R-Y signal that has passed IC400 (PR gain control amplifier), the B-Y signal that has passed IC401 (PB gain control amplifier) and the Y-signal that is inverted and amplified by Q463. The B-signal is generated by adding the Y-signal to the BY signal that has passed IC401 (PB gain control amplifier). 3. RGB Selector Switch IC1300 (1/3), IC1302 (1/3) and IC1303 (1/3) are the selector switch selecting either the RGB signal or the YPBPR signal (matrix circuit). Output of the selector switch is R, G and B signals. 4. Clamp Circuit (2) The R-signal is sampled-and-held by the timing pulse of the deflection system. IC1305 compares the sampled R-signal with the reference signal. The error voltage controls the DC bias of the Rsignal amplifier (Q1300 to Q1302) so that the pedestal level is kept to a constant DC level all the time. The same clamp operation is performed in the G and B signals in the same way. 6-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 5. OSD Insertion Circuit The on-screen display of the R-signal is realized by inserting the OSD blanking with IC1300 (2/3) and by inserting the OSD with IC1304 (1/3). The WINDOW signal that is used during the AUTO W/B adjustment is created by the character generator, and uses the same signal line in the same way for character display. The same insertion operation is performed in the G and B signals in the same way. 6. CUT-OFF Circuit CUT-OFF of the R-signal is performed by IC1304 (2/3, 3/ 3). The same cut-off operation is performed in the G and B signals in the same way. 7. CXA1739 Peripheral Circuit The RGB signal is input during the normal operation and the color difference signal is input during the blue-only mode. (The B-signal is input to the Y input connector.) CXA1739 has the built-in auto cut-off loop. The auto cutoff reference pulse is inserted into every H. period in the order of R, G then B channels at the end of the V. BLKG period (during the 3H period immediately after the rise-up of the V. pulse that is supplied to pin-18) in the output signal from CXA1739. The return pulse of the reference pulse is buffered by Q1402 and input to IC1401 pin-25. The return pulse that is input to pin-25 is compared with the BIAS control voltage by the voltage comparator. The error signal from the comparator is used to shift the DC output voltage until the return pulse agrees with the adjustment voltage. This circuit operation is performed to prevent the changing of the cut-off level caused by the drift of CRT or of the drive circuit. Q1431 to Q1434 in the R-signal output circuit remove the smear that occurs inside the IC. The same circuit operation is performed in the G-channel and the B-channel too. 9. AUTO CHROMA PHASE The signals that are output from IC1401 are selected by IC2380. Only the sample pulse portion of the selected signal is sampled by IC2381 and is compared with the output by IC2382. The error signal from the comparator is fed back to DAC through IC2383 and automatically controls the PB LEVEL or the R LEVEL until the output agrees with the sampled level. 10. B1 Board The B1 board is an aperture correction circuit. The aperture correction performs the frequency compensation at 5 MHz when the input signal is 480/60i and 575/ 501 with DL400/DL401. It performs the frequency compensation at 16 MHz when any other signals are input. DL404 and DL405 are the delay lines that corrects the delay amount of the Y-signal. The PB and PR signals are corrected of their delay amounts by DL501, DL502, DL503 and DL504. Amount of compensation can be varied by 2 to 6 dB when the APT is ON using the aperture correction amplifier. 11. Sync Separator Circuit/B2 Board The sync separator circuit consists of the sync AGC circuit and the B2 board. Either the input sync signal in the mode of 480/60i and 575/501 or that in any other modes, is selected by IC3301 (2/3), (3/3), Q3302 and Q3303. The sync signal is separated by the SYNC AGC circuit of Q3304 to Q3319. Either INT sync or EXT sync is selected by IC3301. In the B2 board, the equalizing pulses are extracted by IC3901, the H. sync pulse is separated by the H. SYNC SEP. circuit consisting of IC3904, IC3905, IC3906, IC3907 and the V. sync pulse is separated by the V. SYNC SEP. circuit consisting of Q3905, Q3907, Q3908. The switch IC3902 is the selector switch that selects either the internal sync separator output or the already separated H. and V. sync signals that are input when the SDI signal is used. 8. ABL Circuit The ABL circuit consists of Q1460 for ABL and Q1461 for BRT ABL. The ABL voltage from the deflection block is input the respective emitters of Q1460 and Q1461. The voltagedivided DC voltage of the ABL signal is input the respective bases of Q1460 and Q1461. Their collectors are connected to IC1401 pin-46 (PIC CONT) and pin-7 (BRT CONT) respectively. When these transistors are turned on, the ABL operation can be performed by decreasing their respective control voltages. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 6-5 6-4. C Board 6-6. MB Board The C board circuit is the CRT drive circuit. The R-signal that is input to CN702 is amplified by about 25 dB and inverted by the cascaded amplifier consisting of Q730, Q732 and Q733, and is sent to the cathode. This amplifier has the frequency compensation characteristics (peaking characteristics) by R733, C730, C776, R746 and L730. Q702 is the auto cut-off circuit that allows to flow the output pulse through R704 via Q735 when Q702 is ON. The reference pulse that is current-to-voltage converted by R704, is input to IC1401 pin-25 through a buffer in the B board in order to activate the auto cut-off circuit. The above-described circuit operations are applied to the G-signal and B-signal. 1. Character Display and Internal Signal Generator IC1107 is the character generator IC such as menu characters. IC1110 generates the 4:3 marker and the various signals for automatic adjustments. Outputs of the two IC are mixed by IC1100 and is output. 6-5. MA Board 3. Parallel Remote Control IC1112 reads out the status of the parallel remote terminal and transfers it to the CPU in the MA board. 1. System Control IC106 (system control CPU) controls the monitor in accordance with the program that is installed in IC108 (flash EEPROM). The program in IC108 can be re-written by the boot loader program in IC106. Various settings are saved in the SRAM (IC111) that is backed up by battery. 2. Serial Communication Driver IC1105 is the communication controller for the serial remote control. It performs the transmission and reception of the serial remote communication together with the RS485 driver of IC1103 and IC1106. IC1108 (communication controller) and IC1109 (RS-232 driver) performs the transmission and reception of the OPTION terminals. 2. Internal Bus inside Monitor Most blocks of the deflection circuits and the signal circuits are controlled by the I2C bus that is driven by IC103 (5/6), (6/6). The I2C bus is controlled of its operation by controlling the general purpose port of IC106 by software. IC112 is an expansion I/O unit that is used to control the internal bus and the TALLY LED. 3. Connection to Options The respective option boards are controlled by IC101 (1/4), (2/4), (3/4), IC103 (1/6), (2/6), (3/6), (4/6) and IC104. The data communication with the option slot bus uses the strobe/hand-shake method using the SLOT ID signal. Data is transferred by MISO/MOSI/SCLK. The MISO/MOSI/ SCLK signal is also used for communication between the MA board and the MB board. IC112 is the RS-422 driver that establishes communication to read the key data or knob information of the internal controller or the control unit and to turn on/off the LED. 6-6 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A IC Section 7 Semiconductors BA05FP-E2 CXA1875AM-T4 MAX202CSE MAX3100CEE-TG068 MC14053BF MC74HC4053F MC74HC4538AF TC74HC4053AFT (EL) TC74HC4538AF 16 Vcc 9 MB89613R-651 64 33 1 32 SC7S02F TC-4S30F TC4S11F TC4S71F TC7S08F TC7S14F TOP VIEW MBM29F400BC-90FP 44 23 GND 1 OUT TOP VIEW BA05T BA12T SE-135N 1 8 1 TOP VIEW 22 TOP VIEW LA6500-FA MC74HC00AFEL MC74HC08AF MC74HC589AFEL TC74HC30AF TC74VHC02F TC74VHC04F TC74VHC125F TC74VHC138F TC74VHC14F VCC GND OUT 14 5 1 4 2 3 8 SN74HC05ANS 1 CXA1211M CXA1521M LM358D LM393PS LTC490CS8 M24C02-MN6T MAX490ECSA MM1026BFB TC4W53FU TC7W00FU TC7W08F TC7W32FU TC7W74FU TL082 UPC4558G2 X25040SI 8 1 14 5 LC35256DM-70-TLM MB90096PF-178 MB90096PF-G-127-BND-ER 28 15 1 1 TOP VIEW MC74HC175FEL TC74VHC244F TC74VHC574F TOP VIEW 9 1 14 7 7 16 1 8 20 11 8 TOP VIEW TOP VIEW NJM7912FA LM2990T-5.0 1 10 TOP VIEW TDA8172 TOP VIEW CXA1544M-T6 NJU3716M-T2 24 1 2 13 1 12 3 13 M62399FP-TE2 2 1 20 11 1 10 TOP VIEW 7 TDA9106 42 22 TOP VIEW 1 21 TOP VIEW BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 7-1 IC, TRANSISTOR TL431CLP UPC1093J 2SA1175-HFE 2SC2785-HFE 2SC3950-D IMX2-T109 4 5 LETTER SIDE 6 3 2 1 4 5 6 E 3 B E C 2SC4686A B 1SS119-25 D1N20R HZS9.1NB2 RD18ESB1 RD27ESB2 RD5.1ESB3 RD6.2ESB2 RD6.8SB2-T1 10 1 2 1 Z8622812PSC 18 C 9 2SA1221-K 2SB734-34 2SD774-34 TOP VIEW 2SA1037AK-T146-QR 2SA1037AK-T146-R 2SA1330-06 2SA1462-T1Y33 2SA1462-Y33 2SC1623-L5L6 2SC3326N-A 2SC3392-5-TB 2SC3545-T43 DTA114EKA-T146 DTA114GKAT146 DTA143ESA-TP DTA144EKA-T146 DTC114EK DTC114GKA DTC114EKA-T146 C B D1 E G1 S1 2SA1381-E 2SC3503-DE LETTER SIDE CATHODE NC S2 G2 D2 2SK2350 2SK2655-01R-F165 ANODE 1SS226 C 3 E B B E 2SA1091-0 2SC2362K-G 2SB1132-P 2SD1834 G 2 D 1 S 3 2SK520K44K45-T1B G B 1 1SS352 RD12ESB2 RD13SB2 RD15SB1 RD3.3SB RD30SB-T1 RD4.7SB2 RD6.2SB S C D E 2SC3746 2SC5450-CA 2SD982 IMT2 4 5 E C 2 6 B 3 2 1 4 B 7-2 6 3 C E 5 2 1 ANODE CATHODE BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A DIODE CL-155Y/PG-CD CATHODE EL1Z GP08D RGP02-17EL-6433 RM11C CATHODE CATHODE D10SC9M ANODE ANODE SC311-6-TE12RA SC802-04 FE3D ANODE CATHODE 12 1 3 2 3 CATHODE D1NL20U-TR D1NL40-TA2 ERA91-02 ERD38-06 RH-1A S2L20UF SLR-325DCT31 SLR-325MCT31 SLR-325VCT31 ANODE MA111-(K8).S0 ANODE CATHODE CATHODE RD10SB1 RD10SB3-T1 RD12SB-T1 RD12SB1-T1 RD5.6SB2 RD7.5SB1-T1 ANODE D4SB60L ANODE CATHODE 2 + – 1 2 + 1 – RD22M-B CATHODE DD54SCLS-YCC-11 ANODE NC CATHODE ANODE BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 7-3 7-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A CABINET Section 8 Exploded Views NOTE : • Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified marked ! are critical for safety. Replace only with the part number specified. • Items with no part number and no description are not stocked because they are seldom required for routine service. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • The construction parts of an assembled part are indicated with a collation number in the remarks column. 8-1. BEZEL, CABINET : 7-682-161-01 : 7-682-561-09 : 7-682-947-01 : 7-685-647-79 : 7-624-200-01 : 7-685-648-79 : 7-685-871-09 : 7-682-963-09 : 7-628-000-04 20 21 +P 4x8 +B 4x8 +PSW 3x6 +BVTP 3x10 NUT, PUSH 1.5 +BVTP 3x12 +BVTT 3x6 +PSW 4x14 +PS 5x14 19 21 17 22 13 14 D14H5 9 16 8 17 15 10 6 11 7 D14H5 18 5 21 23 24 4 1 12 3 23 2 D14H5 11 D14H1 10 D14H5 Ref.No. 1 2 3 Part No. 4 X-4037-285-1 * 3-718-322-02 ( X-4037-278-1 X-4033-145-1 4-050-851-01 5 6 7 8 9 * * * * * 10 11 12 13 A-1372-664-A 4-050-925-04 A-1372-665-A 4-050-924-04 A-1375-185-A * 4-337-212-11 4-050-922-01 ( ** A-1373-742-A A-1373-717-A * A-1373-716-A Description Remark MASK (16:9) ASSY EMBLEM, SONY BEZEL ASSY (D14H5) BEZEL ASSY (D14H1) KNOB, CONTROL (D14H5) 2 Ref.No. 14 15 16 17 HA MOUNT (D14H5) BRACKET (RIGHT), BEZEL (D14H5) HB MOUNT (D14H5) BRACKET (LEFT), BEZEL (D14H5) HC COMPL (D14H5) 18 19 20 HANDLE (D14H5) BASE, HANDLE (D14H5) YB MOUNT (D14H5) YB MOUNT (D14H1) YA MOUNT 22 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 21 23 24 Part No. Description Remark * 4-050-876-01 PLATE, LIGHT INTERCEPTION YC MOUNT (D14H5) YC MOUNT (D14H1) * 4-061-920-01 INSULATOR, YC 4-043-825-01 HANDLE ( ** A-1373-743-A A-1373-718-A * 4-073-226-01 CABINET (R) * 4-073-227-01 CABINET (L) 4-050-931-01 CABINET (UPPER) (D14H5) ( 4-050-967-01 CABINET(UPPER) (D14H1) 4-063-969-01 SCREW (OS), CASE, CLAW ( ** 4-073-201-01 4-073-228-01 PANEL (UPPER), REAR (D14H5) PANEL (UPPER),REAR (D14H1) * X-4033-276-1 GUARD ASSY,HARNESS(L) (D14H1) * X-4033-277-1 GUARD ASSY,HARNESS(S) (D14H1) 8-1 BLOCK 8-2. M BLOCK, SIGNAL BLOCK : 7-685-871-09 : 7-682-950-01 : 7-682-950-09 : 7-682-961-09 : 7-685-648-79 +BVTT 3x6 +PSW 3x12 +PSW 3x12 +PSW 4x8 +BVTP 3x12 70 BKM142HD 63 62 68 61 BKM127W 65 BKM120D 71 OPTION 67 66 BKM-129X 58 64 72 60 59 56 D14H5 69 55 52 57 53 54 D14H1 56 51 Ref.No. 51 52 53 54 55 56 * * * * * Part No. Description A-1136-014-A A-1131-464-A A-1131-463-A 3-703-141-00 4-353-620-11 B COMPL B2 MOUNT B1 MOUNT HOLDER, PWB HINGE, PC BOARD 52,53 57 58 59 PANEL (LOWER), REAR (D14H5) PANEL(LOWER),REAR (D14H1) * A-1372-136-A HD MOUNT (D14H1) ! 1-762-300-11 SWITCH, AC POWER SEESAW ! 1-251-382-11 INLET, AC 3P(WITH NOISE FILTER) 60 61 2-990-241-02 HOLDER (A), PLUG * A-1306-572-A MA COMPL 8-2 ( ** 4-073-208-01 4-073-232-01 Remark Ref.No. Part No. Description 62 63 64 * A-1306-571-A MB COMPL * 4-073-210-01 COLLAR * A-1390-942-A T MOUNT 65 66 67 68 69 * * * * * 70 71 72 3-701-417-02 PURSE LOCK (11 DIA.) * 4-074-027-01 BRACKET, G1 * A-1316-504-A G1 COMPL X-4037-166-1 A-1136-013-A X-4037-154-1 4-050-913-02 4-074-026-01 Remark PANEL ASSY, BLANK BX COMPL PANEL ASSY, CONNECTOR INSULATOR (ANODE) HOLDER,G PWB BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A CHASSIS 8-3. PICTURE TUBE, CHASSIS : 7-682-161-01 : 7-682-564-09 : 7-682-950-01 : 7-688-004-02 +P 4x8 +B 4x14 +PSW 3x12 W4 112 109 108 112 102 107 110 101 111 113 106 104 103 105 114 122 115 127 123 124 116 125 117 118 120 119 121 Ref.No. 101 102 103 Part No. Description Remark Part No. Description Remark 114 115 104 NUT,(B) (M5), FLANGE WASHER, CRT POSITION PICTURE TUBE M34LHF20X (For USA) PICTURE TUBE M34LHF21X (For AEP,AUS) ! 1-451-508-11 DEFLECTION YOKE 116 117 117 * A-1316-456-A G COMPL 115 ! X-4560-177-1 TRANSFORMER ASSY,FLYBACK (NX-4141/J1A4) * 4-073-218-01 GUIDE, PWB * X-4037-279-1 CHASSIS ASSY, BOTTOM (D14H5)118 * X-4037-288-1 CHASSIS ASSY,BOTTOM (D14H1) 105 106 107 108 109 4-053-410-02 X-2105-533-1 4-050-492-01 * 4-047-349-01 * A-1331-883-A SHIELD, DY PLATE ASSY, CORRECTION, TLH SPACER, DY HOLDER, HV CABLE C MOUNT 118 119 120 121 122 3-840-486-02 X-4033-117-1 X-4836-202-9 * 3-668-845-01 4-308-870-00 CUSHION, SPEAKER FOOT ASSY FOOT CUSHION, LEG CLIP,LEAD WIRE 110 111 112 113 4-303-774-03 ! 1-411-660-21 4-395-824-01 * 4-382-050-01 SPRING COIL, DEMAGNETIC HOLDER, DEGAUSSING COIL BAND, C PC BOARD 123 124 125 127 1-452-032-00 1-452-094-00 4-051-735-22 * 3-687-542-41 MAGNET,DISC (10MMφ) MAGNET,ROTATABLE DISK:15MMφ PIECE A(75), CONV. CORRECT SPACER, PC BOARD SPACE ( 4-306-034-00 4-348-567-00 ! 8-738-335-05 ! 8-738-333-05 Ref.No. BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 120,121 8-3 8-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Ref.No. Part No. Section 9 Electrical Parts List Remark Ref.No. Part No. Description B Description Remark NOTE : • Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. The components identified marked ! are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Ref.No. Part No. RESISTORS • All resistors are in ohms. • F: nonflammable • METAL: Metal-film resistor • METAL OXIDE: Metal oxide-film resistor Description Remark * A-1136-014-A B COMPL ********* Including B1 and B2 MOUNTRef.No. Part No. Description Remark C461 C462 C463 C464 C465 1-126-390-11 1-163-031-11 1-163-031-11 1-163-031-11 1-126-394-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 22µF 0.01µF 0.01µF 0.01µF 10µF 20% 20% C300 C301 C304 C305 C306 1-163-031-11 1-163-031-11 1-104-760-11 1-163-021-91 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.047µF 10% 0.01µF 10% 0.01µF 50V 50V 50V 50V 50V C466 C467 C468 C485 C486 1-126-394-11 1-163-031-11 1-163-031-11 1-126-390-11 1-126-390-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP 10µF 0.01µF 0.01µF 22µF 22µF C307 C308 C309 C310 C311 1-164-505-11 1-115-152-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 2.2µF 22µF 0.01µF 0.01µF 0.01µF 16V 6.3V 50V 50V 50V C487 C488 C489 C490 C491 1-163-031-11 1-163-031-11 1-163-031-11 1-126-394-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 10µF 0.01µF C312 C332 C333 C334 C335 1-126-390-11 1-104-760-11 1-163-021-91 1-163-031-11 1-164-505-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22µF 20% 0.047µF 10% 0.01µF 10% 0.01µF 2.2µF 6.3V 50V 50V 50V 16V C492 C494 C1300 C1301 C1302 1-163-031-11 1-126-396-11 1-163-031-11 1-163-031-11 1-163-087-00 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 47µF 0.01µF 0.01µF 4PF C336 C337 C338 C339 C340 1-163-031-11 1-163-031-11 1-115-152-11 1-164-505-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 22µF 2.2µF 0.01µF 20% 50V 50V 6.3V 16V 50V C1304 C1305 C1306 C1307 C1308 1-104-760-11 1-163-021-91 1-109-982-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047µF 10% 0.01µF 10% 1µF 10% 0.01µF 0.01µF C341 C367 C368 C369 C370 1-163-031-11 1-104-760-11 1-163-021-91 1-163-031-11 1-164-505-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.047µF 10% 0.01µF 10% 0.01µF 2.2µF 50V 50V 50V 50V 16V C1309 C1310 C1320 C1321 C1322 1-164-505-11 1-164-346-11 1-163-031-11 1-163-031-11 1-163-091-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 2.2µF 1µF 0.01µF 0.01µF 8PF C371 C372 C373 C374 C375 1-163-031-11 1-163-031-11 1-115-152-11 1-164-505-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 22µF 2.2µF 0.01µF 50V 50V 6.3V 16V 50V C1324 C1325 C1326 C1327 C1330 1-104-760-11 1-163-021-91 1-163-031-11 1-163-031-11 1-164-346-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047µF 10% 0.01µF 10% 0.01µF 0.01µF 1µF C376 C377 C378 C386 C387 1-163-031-11 1-126-396-11 1-126-396-11 1-126-916-11 1-126-916-11 CERAMIC CHIP ELECT CHIP ELECT CHIP ELECT ELECT 0.01µF 47µF 47µF 1000µF 1000µF 50V 16V 16V 6.3V 6.3V C1340 C1341 C1342 C1344 C1345 1-163-031-11 1-163-031-11 1-163-086-00 1-104-760-11 1-163-021-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 50V 0.01µF 50V 3PF 0.25PF 50V 0.047µF 10% 50V 0.01µF 10% 50V C450 C451 C452 C454 C460 1-126-394-11 1-163-031-11 1-163-031-11 1-126-396-11 1-126-390-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP 10µF 0.01µF 0.01µF 47µF 22µF 16V 50V 50V 16V 6.3V C1346 C1347 C1348 C1350 C1400 1-163-031-11 1-163-031-11 1-163-251-11 1-164-346-11 1-163-035-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 100PF 5% 1µF 0.047µF BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 6.3V 50V 50V 50V 16V 20% 20% 20% 16V 50V 50V 6.3V 6.3V 50V 50V 50V 16V 50V 50V 16V 50V 50V 0.25PF 50V 20% 50V 50V 10V 50V 50V 16V 16V 50V 50V 0.25PF 50V 50V 50V 50V 50V 16V 50V 50V 50V 16V 50V 9-1 B Ref.No. Part No. Description Ref.No. Part No. Description C1401 C1402 C1404 C1405 C1406 1-163-035-00 1-163-035-00 1-163-031-11 1-163-035-00 1-163-809-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047µF 0.047µF 0.01µF 0.047µF 0.047µF 10% 50V 50V 50V 50V 25V C3306 C3307 C3308 C3309 C3311 1-163-257-11 1-163-251-11 1-164-346-11 1-126-390-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 180PF 100PF 1µF 22µF 0.1µF C1407 C1408 C1409 C1410 C1411 1-163-809-11 1-163-809-11 1-164-489-11 1-164-004-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047µF 0.047µF 0.22µF 0.1µF 0.1µF 10% 10% 10% 10% 10% 25V 25V 16V 25V 25V C3312 C3313 C3314 C3316 C3332 1-163-038-91 1-163-263-11 1-163-038-91 1-163-038-91 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 330PF 0.1µF 0.1µF 0.01µF C1412 C1413 C1414 C1415 C1416 1-164-004-11 1-163-251-11 1-163-275-11 1-163-038-91 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 100PF 0.001µF 0.1µF 0.1µF 10% 5% 5% 25V 50V 50V 25V 25V C3333 C3339 C3341 C3342 C3344 1-163-031-11 1-163-038-91 1-163-251-11 1-163-251-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.1µF 100PF 100PF 0.1µF 5% 5% 10% 50V 25V 50V 50V 25V C1417 C1418 C1419 C1420 C1421 1-164-004-11 1-164-004-11 1-163-251-11 1-163-275-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 100PF 0.001µF 0.1µF 10% 10% 5% 5% 25V 25V 50V 50V 25V C3350 C3402 C3403 C3405 C3406 1-164-005-11 1-163-031-11 1-163-031-11 1-163-038-91 1-164-182-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47µF 0.01µF 0.01µF 0.1µF 0.0033µF 10% 25V 50V 50V 25V 50V C1422 C1423 C1424 C1425 C1426 1-164-004-11 1-164-004-11 1-163-251-11 1-163-275-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 100PF 0.001µF 0.1µF 10% 10% 5% 5% 25V 25V 50V 50V 25V C3407 C3408 C3410 C3411 C3412 1-164-344-11 1-126-394-11 1-164-004-11 1-163-259-91 1-164-004-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.068µF 10µF 0.1µF 220PF 0.1µF 25V 16V 25V 50V 25V C1427 C1428 C1429 C1431 C1450 1-163-038-91 1-164-004-11 1-163-038-91 1-163-251-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 0.1µF 100PF 0.01µF 25V 25V 25V 50V 50V C3432 C3433 C4300 C4302 C4303 1-163-035-00 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C1451 C1460 C1461 C1462 C1464 1-163-251-11 1-164-005-11 1-163-031-11 1-163-031-11 1-164-005-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.47µF 0.01µF 0.01µF 0.47µF 50V 25V 50V 50V 25V C4350 C4351 C4352 C4353 C4354 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C1465 C1466 C1467 C1468 C1469 1-163-031-11 1-163-031-11 1-126-935-11 1-126-396-11 1-126-396-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT CHIP ELECT CHIP 0.01µF 0.01µF 470µF 47µF 47µF C4355 1-126-396-11 ELECT CHIP 20% 20% 20% 50V 50V 16V 16V 16V C2300 C2310 C2311 C2315 C2330 1-163-222-11 1-126-396-11 1-163-031-11 1-163-224-11 1-163-092-00 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 5PF 47µF 0.01µF 7PF 9PF 0.25PF 50V 20% 16V 50V 0.5PF 50V 0.25PF 50V C2351 C2352 C2353 C2361 C2362 1-163-031-11 1-163-031-11 1-163-031-11 1-126-396-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 47µF 0.01µF 50V 50V 50V 16V 50V C2363 C2364 C2383 C2384 C2385 1-126-396-11 1-163-031-11 1-163-031-11 1-163-009-11 1-163-009-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47µF 20% 0.01µF 0.01µF 0.001µF 10% 0.001µF 10% 16V 50V 50V 50V 50V C2386 C2387 C2388 C2389 C2390 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C3301 C3302 C3303 C3304 C3305 1-126-394-11 1-163-251-11 1-163-251-11 1-163-257-11 1-163-251-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10µF 100PF 100PF 180PF 100PF 9-2 Remark 10% 10% 5% 5% 20% 20% 5% 5% 5% 5% 16V 50V 50V 50V 50V Remark 47µF 5% 5% 20% 5% 10% 20% 10% 5% 10% 20% 50V 50V 16V 6.3V 25V 25V 50V 25V 25V 50V 16V CN301 CN302 CN303 CN304 CN307 1-764-334-11 * 1-564-509-11 * 1-564-510-11 * 1-564-513-11 * 1-564-512-11 PLUG, CONNECTOR 11P PLUG, CONNECTOR 6P PLUG, CONNECTOR 7P PLUG, CONNECTOR 10P PLUG, CONNECTOR 9P CN308 CN411 CN412 CN421 CN422 * 1-564-512-11 * 1-506-611-11 * 1-506-611-11 * 1-779-070-21 * 1-779-070-21 PLUG, CONNECTOR 9P PIN, CONNECTOR 8P PIN, CONNECTOR 8P PIN, CONNECTOR 12P PIN, CONNECTOR 12P D1400 D1401 D1402 D1403 D1404 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-037-17 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD10SB3-T1 D3301 D3302 D3307 D3308 D4401 8-719-016-74 8-719-016-74 8-719-800-76 8-719-800-76 8-719-158-09 DIODE 1SS352 DIODE 1SS352 DIODE 1SS226 DIODE 1SS226 DIODE RD4.7SB2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark Q453 Q460 8-729-112-65 TRANSISTOR 2SA1462-T1Y33 8-729-112-65 TRANSISTOR 2SA1462-Y33 Q461 Q462 Q463 Q464 Q465 8-729-107-31 8-729-120-28 8-729-107-31 8-729-107-31 8-729-026-50 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1037AK-T146-QR Q466 Q485 Q486 Q487 Q1300 8-729-026-50 8-729-120-28 8-729-107-31 8-729-107-31 8-729-112-65 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-Y33 Q1301 Q1302 Q1303 Q1304 Q1305 8-729-107-31 8-729-120-28 8-729-120-28 8-729-120-28 8-729-026-50 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR Q1320 Q1321 Q1322 Q1323 Q1340 8-729-112-65 8-729-107-31 8-729-120-28 8-729-120-28 8-729-112-65 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 Q1341 Q1342 Q1343 Q1400 Q1401 8-729-107-31 8-729-120-28 8-729-120-28 1-801-806-11 8-729-120-28 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SC1623-L5L6 Q1402 Q1410 Q1411 Q1412 Q1413 8-729-026-50 8-729-112-65 8-729-120-28 8-729-112-65 8-729-107-31 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 Q1414 Q1420 Q1421 Q1422 Q1423 8-729-120-28 8-729-112-65 8-729-120-28 8-729-112-65 8-729-107-31 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 Q1424 Q1430 Q1431 Q1432 Q1433 8-729-120-28 8-729-112-65 8-729-120-28 8-729-112-65 8-729-107-31 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 Q1434 Q1460 Q1461 Q1462 Q1463 8-729-120-28 8-729-120-28 8-729-120-28 1-801-806-11 8-729-900-53 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC114EK Q300 Q301 Q302 Q303 Q304 8-729-112-65 8-729-107-31 8-729-920-59 8-729-107-31 8-729-107-31 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR IMX2-T109 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 Q2300 Q2301 Q2302 Q2303 Q2315 8-729-112-65 8-729-107-31 8-729-112-65 8-729-112-65 8-729-112-65 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SA1462-Y33 Q330 Q331 Q332 Q333 Q334 8-729-112-65 8-729-107-31 8-729-920-59 8-729-107-31 8-729-107-31 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR IMX2-T109 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 Q2316 Q2317 Q2318 Q2330 Q2331 8-729-107-31 8-729-112-65 8-729-112-65 8-729-112-65 8-729-107-31 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 Q365 Q366 Q367 Q368 Q369 8-729-112-65 8-729-107-31 8-729-920-59 8-729-107-31 8-729-107-31 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR IMX2-T109 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 Q2332 Q2333 Q2380 Q2381 Q2382 8-729-112-65 8-729-112-65 8-729-120-28 8-729-120-28 8-729-120-28 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 Q450 Q451 Q452 8-729-120-28 TRANSISTOR 2SC1623-L5L6 8-729-107-31 TRANSISTOR 2SC3545-T43 8-729-107-31 TRANSISTOR 2SC3545-T43 Q2383 Q3301 Q3302 8-729-120-28 TRANSISTOR 2SC1623-L5L6 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR IC300 IC301 IC302 IC303 IC304 8-759-011-65 8-759-011-65 8-759-011-65 8-759-981-48 8-759-981-48 IC MC74HC4053F IC MC74HC4053F IC MC74HC4053F IC TL082M IC TL082M IC305 IC306 IC307 IC308 IC400 8-759-981-48 8-752-054-80 8-752-054-80 8-752-054-80 8-752-053-21 IC TL082M IC CXA1521M IC CXA1521M IC CXA1521M IC CXA1211M IC401 IC1300 IC1302 IC1303 IC1304 8-752-053-21 8-759-011-65 8-759-011-65 8-759-011-65 8-759-011-65 IC CXA1211M IC MC74HC4053F IC MC74HC4053F IC MC74HC4053F IC MC74HC4053F IC1305 IC1306 IC1307 IC1308 IC1309 8-759-981-48 8-759-981-48 8-759-981-48 8-759-011-65 8-759-011-65 IC TL082M IC TL082M IC TL082M IC MC74HC4053F IC MC74HC4053F IC1400 IC1401 IC2380 IC2381 IC2382 8-759-038-15 8-752-067-05 8-759-523-02 8-759-523-02 8-759-988-13 IC MC74HC4538AF IC CXA1739S IC TC74HC4053AFT(EL) IC TC74HC4053AFT(EL) IC LM393PS IC2383 IC3301 IC3400 IC3401 IC3403 8-759-083-94 8-759-523-02 8-759-424-13 8-759-032-14 8-759-328-12 IC TC7W74FU IC TC74HC4053AFT(EL) IC MC74HC00AFEL IC MC74HC08AF IC Z8622812PSC IC3404 IC3406 IC3407 IC4300 IC4301 8-759-527-74 8-759-084-79 8-759-242-76 8-752-072-94 8-752-072-94 IC M24C02-MN6T IC TC7S14F IC TC7W08F IC CXA1875AM-T4 IC CXA1875AM-T4 IC4302 IC4350 IC4351 IC4352 8-752-072-94 8-752-072-94 8-759-482-47 8-759-482-47 IC CXA1875AM-T4 IC CXA1875AM-T4 IC M62399FP-TE2 IC M62399FP-TE2 L300 1-406-665-11 CHOKE 100µH BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 9-3 B Ref.No. Part No. Description Remark Q3303 Q3304 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR 8-729-920-59 TRANSISTOR IMX2-T109 Q3305 Q3306 Q3307 Q3308 Q3309 8-729-920-59 8-729-120-28 8-729-026-50 8-729-107-31 8-729-120-28 TRANSISTOR IMX2-T109 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 Q3310 Q3311 Q3312 Q3313 Q3314 8-729-925-42 8-729-120-28 8-729-026-50 8-729-120-28 8-729-920-59 TRANSISTOR IMT2 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC1623-L5L6 TRANSISTOR IMX2-T109 Q3315 Q3316 Q3317 Q3318 Q3319 8-729-112-65 8-729-120-28 8-729-925-42 8-729-026-50 8-729-120-28 TRANSISTOR 2SA1462-Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR IMT2 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC1623-L5L6 Q3402 1-801-806-11 TRANSISTOR DTC144EKA-T146 R300 R301 R302 R303 R305 1-216-049-91 1-216-025-91 1-216-657-11 1-216-663-11 1-216-651-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 1K 100 1.8K 3.3K 1K 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R306 R307 R308 R309 R310 1-216-025-91 1-216-653-11 1-216-025-91 1-216-049-91 1-216-049-91 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.2K 100 1K 1K 5% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R311 R312 R313 R314 R315 1-216-029-00 1-216-675-91 1-218-776-11 1-216-675-91 1-218-764-11 RES,CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 150 10K 1M 10K 330K 5% 0.50% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R316 R317 R318 R319 R320 1-216-033-00 1-216-025-91 1-216-053-00 1-216-685-11 1-216-679-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 220 100 1.5K 27K 15K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R321 R322 R323 R324 R325 1-216-089-91 1-216-681-11 1-216-025-91 1-216-057-00 1-216-037-00 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 47K 18K 100 2.2K 330 5% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R330 R331 R332 R333 R335 1-216-049-91 1-216-025-91 1-216-657-11 1-216-663-11 1-216-651-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 1K 100 1.8K 3.3K 1K 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R336 R337 R338 R339 R340 1-216-025-91 1-216-653-11 1-216-025-91 1-216-049-91 1-216-049-91 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.2K 100 1K 1K 5% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R341 R342 R343 R344 R345 1-216-025-91 1-216-675-91 1-218-776-11 1-216-675-91 1-218-770-11 RES,CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 1M 10K 560K 5% 0.50% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R346 R347 R348 R349 R350 1-216-033-00 1-216-025-91 1-216-053-00 1-216-683-11 1-218-759-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 220 100 1.5K 22K 200K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W 9-4 Ref.No. Part No. Description Remark R351 R353 R354 R355 R356 1-216-693-11 1-216-089-91 1-216-025-91 1-216-057-91 1-216-033-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 56K 47K 100 2.2K 220 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R365 R366 R367 R368 R370 1-216-049-91 1-216-025-91 1-216-657-11 1-216-663-11 1-216-651-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 1K 100 1.8K 3.3K 1K 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R371 R372 R373 R374 R375 1-216-025-91 1-216-653-11 1-216-025-91 1-216-049-91 1-216-049-91 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.2K 100 1K 1K 5% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R376 R377 R378 R379 R380 1-216-025-91 1-216-675-91 1-218-776-11 1-216-675-91 1-218-770-11 RES,CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 10K 1M 10K 560K 5% 0.50% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R381 R382 R383 R384 R385 1-216-033-00 1-216-025-91 1-216-053-00 1-216-683-11 1-218-759-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 220 100 1.5K 22K 200K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R386 R388 R389 R390 R391 1-216-693-11 1-216-089-91 1-216-025-91 1-216-057-00 1-216-033-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 56K 47K 100 2.2K 220 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R450 R451 R452 R453 R454 1-216-025-91 1-216-049-91 1-216-647-11 1-216-649-11 1-216-645-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 680 820 560 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R455 R456 R457 R458 R459 1-216-647-11 1-216-065-91 1-216-029-91 1-216-025-91 1-216-057-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 680 4.7K 150 100 2.2K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R460 R461 R462 R463 R464 1-216-671-11 1-216-667-11 1-216-671-11 1-216-667-11 1-216-660-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 6.8K 4.7K 6.8K 4.7K 2.4K 0.50% 0.50% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R465 R466 R467 R468 R469 1-216-668-11 1-216-663-11 1-216-649-11 1-216-045-00 1-216-045-00 METAL CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 5.1K 3.3K 820 680 680 0.50% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R470 R471 R472 R473 R474 1-216-651-11 1-216-061-00 1-216-025-91 1-216-049-91 1-216-647-11 METAL CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 1K 3.3K 100 1K 680 0.50% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R475 R476 R477 R478 R479 1-216-647-11 1-216-647-11 1-216-645-11 1-216-065-91 1-216-065-91 METAL CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 680 680 560 4.7K 4.7K 0.50% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R480 R481 R482 R483 R484 1-216-025-91 1-216-057-00 1-216-025-91 1-216-645-11 1-216-013-91 RES,CHIP RES,CHIP RES,CHIP METAL CHIP RES,CHIP 100 2.2K 100 560 33 5% 5% 5% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B Ref.No. Part No. Description Remark Ref.No. Part No. Description R485 R486 R487 R488 R489 1-216-671-11 1-216-661-11 1-216-671-11 1-216-667-11 1-216-025-91 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 6.8K 2.7K 6.8K 4.7K 100 0.50% 0.50% 0.50% 0.50% 5% R490 R491 R492 R493 R494 1-216-049-91 1-216-647-11 1-216-647-11 1-216-647-11 1-216-645-11 RES,CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 680 680 680 560 R495 R497 R498 R499 R1300 1-216-065-91 1-216-025-91 1-216-057-00 1-216-029-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP R1301 R1302 R1303 R1305 R1306 1-216-663-11 1-216-657-11 1-216-651-11 1-216-025-91 1-216-653-11 R1307 R1308 R1309 R1310 R1311 1/10W 1/10W 1/10W 1/10W 1/10W R1400 R1401 R1402 R1405 R1406 1-216-025-91 1-216-295-91 1-216-073-00 1-216-025-91 1-216-025-91 RES,CHIP SHORT RES,CHIP RES,CHIP RES,CHIP 100 0 10K 100 100 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W 5% 0.50% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1407 R1408 R1409 R1410 R1411 1-216-025-91 1-216-049-91 1-216-049-91 1-216-025-91 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 1K 1K 100 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 4.7K 100 2.2K 150 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1412 R1413 R1414 R1415 R1416 1-216-089-91 1-216-085-00 1-216-085-00 1-216-113-00 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 33K 33K 470K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W METAL CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 3.3K 1.8K 1K 100 1.2K 0.50% 0.50% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1417 R1418 R1419 R1420 R1421 1-216-063-91 1-216-049-91 1-216-073-00 1-216-095-00 1-216-041-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 3.9K 1K 10K 82K 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-025-91 1-216-049-91 1-218-776-11 1-216-675-91 1-216-073-00 RES,CHIP RES,CHIP METAL CHIP METAL CHIP RES,CHIP 100 1K 1M 10K 10K 5% 5% 0.50% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1422 R1423 R1424 R1425 R1426 1-216-049-91 1-216-041-00 1-216-049-91 1-216-065-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 470 1K 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1312 R1313 R1314 R1315 R1316 1-216-073-00 1-216-025-91 1-216-057-00 1-216-295-91 1-216-675-91 RES,CHIP RES,CHIP RES,CHIP SHORT METAL CHIP 10K 100 2.2K 0 10K 5% 5% 5% 1/10W 1/10W 1/10W 0.50% 1/10W R1427 R1428 R1429 R1430 R1431 1-216-063-91 1-216-049-91 1-216-073-00 1-216-095-00 1-216-041-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 3.9K 1K 10K 82K 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1317 R1318 R1319 R1320 R1321 1-216-689-11 1-216-065-91 1-216-065-91 1-216-025-91 1-216-663-11 METAL CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 39K 4.7K 4.7K 100 3.3K 0.50% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1432 R1433 R1434 R1435 R1436 1-216-049-91 1-216-041-00 1-216-049-91 1-216-065-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 470 1K 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1322 R1323 R1325 R1326 R1327 1-216-657-11 1-216-651-11 1-216-025-91 1-216-653-11 1-216-025-91 METAL CHIP METAL CHIP RES,CHIP METAL CHIP RES,CHIP 1.8K 1K 100 1.2K 100 0.50% 0.50% 5% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1437 R1438 R1439 R1440 R1441 1-216-063-91 1-216-049-91 1-216-073-00 1-216-095-00 1-216-041-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 3.9K 1K 10K 82K 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1328 R1329 R1330 R1331 R1332 1-216-049-91 1-218-776-11 1-216-675-91 1-216-025-91 1-216-057-00 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 1K 1M 10K 100 2.2K 5% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1442 R1443 R1444 R1445 R1446 1-216-049-91 1-216-041-00 1-216-049-91 1-216-065-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 470 1K 4.7K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1333 R1334 R1335 R1340 R1341 1-216-295-91 1-216-073-00 1-216-073-00 1-216-025-91 1-216-663-11 SHORT RES,CHIP RES,CHIP RES,CHIP METAL CHIP 0 10K 10K 100 3.3K 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W R1447 R1450 R1451 R1452 R1453 1-216-097-91 1-216-675-91 1-216-089-91 1-216-687-11 1-216-687-11 RES,CHIP METAL CHIP RES,CHIP METAL CHIP METAL CHIP 100K 10K 47K 33K 33K 5% 0.50% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1342 R1343 R1345 R1346 R1347 1-216-657-11 1-216-651-11 1-216-025-91 1-216-653-11 1-216-025-91 METAL CHIP METAL CHIP RES,CHIP METAL CHIP RES,CHIP 1.8K 1K 100 1.2K 100 0.50% 0.50% 5% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1454 R1455 R1456 R1457 R1460 1-216-687-11 1-216-085-00 1-216-085-00 1-216-085-00 1-216-113-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33K 33K 33K 33K 470K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1348 R1349 R1350 R1351 R1352 1-216-049-91 1-218-776-11 1-216-675-91 1-216-025-91 1-216-057-00 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 1K 1M 10K 100 2.2K 5% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1461 R1464 R1466 R1467 R1469 1-216-085-00 1-216-689-11 1-216-113-00 1-216-083-00 1-216-667-11 RES,CHIP METAL CHIP RES,CHIP RES,CHIP METAL CHIP 33K 39K 470K 27K 4.7K 5% 0.50% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1353 R1354 R1355 R1357 R1358 1-216-295-91 1-216-685-11 1-216-691-11 1-216-073-00 1-216-073-00 SHORT METAL CHIP METAL CHIP RES,CHIP RES,CHIP 0 27K 47K 10K 10K 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W R1470 R1471 R1472 R1473 R1480 1-216-671-11 1-216-689-11 1-218-768-11 1-216-073-00 1-216-069-00 METAL CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 6.8K 39K 470K 10K 6.8K 0.50% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Remark 9-5 B Ref.No. Part No. Description Ref.No. Part No. Description R1481 R1482 R1483 R1484 R1485 1-216-065-91 1-216-061-00 1-216-089-91 1-216-085-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 3.3K 47K 33K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3309 R3310 R3311 R3312 R3313 1-216-049-91 1-216-057-00 1-216-057-00 1-216-049-91 1-216-063-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 2.2K 2.2K 1K 3.9K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2300 R2301 R2302 R2303 R2304 1-216-025-91 1-216-065-91 1-216-009-91 1-216-035-00 1-216-645-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 100 4.7K 22 270 560 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3314 R3315 R3316 R3317 R3318 1-216-053-00 1-216-065-91 1-216-687-11 1-216-663-11 1-216-651-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 1.5K 4.7K 33K 3.3K 1K 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2305 R2307 R2308 R2309 R2310 1-216-643-11 1-216-025-91 1-216-055-00 1-216-025-91 1-216-049-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470 100 1.8K 100 1K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3319 R3320 R3321 R3322 R3323 1-216-083-00 1-216-037-00 1-216-679-11 1-216-097-91 1-216-659-11 RES,CHIP RES,CHIP METAL CHIP RES,CHIP METAL CHIP 27K 330 15K 100K 2.2K 5% 5% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2313 R2314 R2315 R2316 R2317 1-216-295-91 1-216-615-91 1-216-025-91 1-216-065-91 1-216-009-91 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 0 33 100 4.7K 22 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R3324 R3325 R3326 R3327 R3328 1-216-655-11 1-216-041-00 1-216-029-00 1-216-111-00 1-216-659-11 METAL CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 1.5K 470 150 390K 2.2K 0.50% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2318 R2319 R2320 R2322 R2323 1-216-035-00 1-216-645-11 1-216-643-11 1-216-025-91 1-216-055-00 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 270 560 470 100 1.8K 5% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3329 R3330 R3331 R3332 R3333 1-216-681-11 1-216-676-11 1-216-059-00 1-216-075-00 1-216-669-11 METAL CHIP METAL CHIP RES,CHIP RES,CHIP METAL CHIP 18K 11K 2.7K 12K 5.6K 0.50% 0.50% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2324 R2325 R2327 R2329 R2330 1-216-025-91 1-216-049-91 1-216-295-91 1-216-615-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP METAL CHIP RES,CHIP 100 1K 0 33 100 5% 5% 1/10W 1/10W 0.5% 5% 1/10W 1/10W R3334 R3335 R3336 R3337 R3338 1-216-659-11 1-216-659-11 1-216-640-11 1-216-069-00 1-216-057-00 METAL CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 2.2K 2.2K 360 6.8K 2.2K 0.50% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2331 R2332 R2333 R2334 R2335 1-216-065-91 1-216-009-91 1-216-035-00 1-216-645-11 1-216-643-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 4.7K 22 270 560 470 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3339 R3340 R3341 R3342 R3343 1-216-037-00 1-216-693-11 1-218-768-11 1-216-097-91 1-216-696-11 RES,CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 330 56K 470K 100K 75K 5% 0.50% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2337 R2338 R2339 R2340 R2342 1-216-025-91 1-216-055-00 1-216-025-91 1-216-049-91 1-216-295-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.8K 100 1K 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R3344 R3345 R3346 R3347 R3381 1-216-661-11 1-216-073-00 1-216-099-00 1-216-687-11 1-216-683-11 METAL CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 2.7K 10K 120K 33K 22K 0.50% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R2344 R2380 R2381 R2382 R2383 1-216-615-91 1-216-025-91 1-216-057-00 1-216-025-91 1-216-057-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 100 2.2K 100 2.2K 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3382 R3385 R3400 R3401 R3402 1-216-031-00 1-216-049-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 180 1K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2384 R2385 R2386 R2387 R2388 1-216-025-91 1-216-057-00 1-216-025-91 1-216-057-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 2.2K 100 2.2K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3403 R3410 R3411 R3412 R3413 1-216-097-91 1-216-049-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 1K 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2389 R2390 R2391 R2392 R2393 1-216-073-00 1-216-057-00 1-216-073-00 1-216-073-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 2.2K 10K 10K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3414 R3416 R3417 R3418 R3419 1-216-049-91 1-216-049-91 1-216-049-91 1-216-069-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 6.8K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3299 R3300 R3301 R3302 R3303 1-216-025-91 1-216-025-91 1-216-053-00 1-216-079-00 1-216-091-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 1.5K 18K 56K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3421 R3422 R3423 R3424 R3425 1-216-025-91 1-216-025-91 1-216-025-91 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3304 R3305 R3306 R3307 R3308 1-216-013-00 1-216-013-00 1-216-013-00 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 33 33 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3426 R3427 R3428 R3429 R3430 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 9-6 Remark Remark BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B B1 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R3431 R3433 R3434 R4300 R4301 1-216-295-91 1-216-025-91 1-216-025-91 1-216-073-00 1-216-073-00 SHORT RES,CHIP RES,CHIP RES,CHIP RES,CHIP 0 100 100 10K 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R4302 R4303 R4304 R4305 R4306 1-216-073-00 1-216-073-00 1-216-033-00 1-216-033-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 220 220 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C401 C402 C403 C404 C407 1-126-396-11 1-126-396-11 1-163-031-11 1-163-031-11 1-163-038-91 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47µF 47µF 0.01µF 0.01µF 0.1µF R4307 R4308 R4309 R4310 R4311 1-216-073-00 1-216-073-00 1-216-073-00 1-216-033-00 1-216-033-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 10K 220 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C410 C411 C412 C502 C503 1-163-038-91 1-165-319-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 0.01µF 0.01µF 0.01µF R4312 R4313 R4314 R4315 R4316 1-216-073-00 1-216-073-00 1-216-073-00 1-216-049-91 1-216-033-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 10K 1K 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4317 R4320 R4417 R4420 R4423 1-216-033-00 1-216-057-00 1-216-073-00 1-216-033-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 220 2.2K 10K 220 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4426 R4434 R4435 R4436 R4437 1-216-033-00 1-216-049-91 1-216-073-00 1-216-677-11 1-216-668-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 220 1K 10K 12K 5.1K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R4438 R4439 R4440 R4441 R4442 1-216-073-00 1-216-073-00 1-216-073-00 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4443 R4444 R4445 R4446 R4447 1-216-033-00 1-216-033-00 1-216-071-00 1-216-131-11 1-216-071-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 220 220 8.2K 2.7M 8.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4448 R4449 R4450 R4451 R4452 1-216-071-00 1-216-131-11 1-216-131-11 1-216-071-00 1-216-131-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 8.2K 2.7M 2.7M 8.2K 2.7M 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4453 R4454 R4455 R4456 R4457 1-216-073-00 1-216-033-00 1-216-033-00 1-216-073-00 1-216-071-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 220 220 10K 8.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4458 R4459 R4460 R4461 R4462 1-216-061-00 1-216-131-11 1-216-057-00 1-216-071-00 1-216-131-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 3.3K 2.7M 2.2K 8.2K 2.7M 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R4471 R4472 1-216-025-91 RES,CHIP 1-216-025-91 RES,CHIP 100 100 5% 5% 1/10W 1/10W * A-1131-463-A B1 MOUNT *********** 20% 20% 16V 16V 50V 50V 25V 25V 50V 50V 50V 50V CN401 * 1-568-015-11 SOCKET, CONNECTOR 8P CN402 * 1-568-015-11 SOCKET, CONNECTOR 8P DL400 DL401 DL402 DL403 DL404 1-411-450-11 1-411-450-11 1-234-455-21 1-234-455-21 1-411-451-11 DELAY LINE DELAY LINE DELAY LINE DELAY LINE DELAY LINE DL405 DL501 DL502 DL503 DL504 1-234-456-21 1-402-770-11 1-416-476-21 1-402-770-11 1-416-476-21 DELAY LINE DELAY LINE DELAY LINE DELAY LINE DELAY LINE IC410 IC450 IC501 8-759-011-65 IC MC74HC4053F 8-752-053-21 IC CXA1211M 8-759-011-65 IC MC74HC4053F **************************************************************** BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Q400 Q401 Q402 Q403 Q404 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28 8-729-026-50 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR Q405 Q406 Q407 Q408 Q409 8-729-112-65 8-729-112-65 8-729-112-65 8-729-107-31 8-729-107-31 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC3545-T43 Q410 Q411 Q412 Q413 Q414 1-801-806-11 8-729-120-28 8-729-107-31 8-729-120-28 8-729-107-31 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 Q501 Q502 Q503 Q504 Q505 8-729-026-50 8-729-107-31 8-729-112-65 8-729-026-50 8-729-107-31 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC3545-T43 Q506 Q511 Q512 Q513 Q514 8-729-112-65 8-729-120-28 8-729-107-31 8-729-112-65 8-729-107-31 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SC3545-T43 9-7 B1 B2 Ref.No. Part No. Description Q515 Q516 Q517 Q518 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-T1Y33 TRANSISTOR 2SC3545-T43 8-729-120-28 8-729-107-31 8-729-112-65 8-729-107-31 Remark Ref.No. Part No. Description Remark R515 1-216-651-11 METAL CHIP 1K 0.50% 1/10W R516 R517 R518 R519 R520 1-216-651-11 1-216-025-91 1-216-025-91 1-216-057-00 1-216-025-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 100 100 2.2K 100 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R400 R401 R402 R403 R404 1-216-025-91 1-216-057-00 1-216-651-11 1-216-025-91 1-216-057-00 RES,CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 100 2.2K 1K 100 2.2K 5% 5% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R521 R522 R523 R524 R531 1-216-037-00 1-216-631-11 1-216-631-11 1-216-025-91 1-216-057-00 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 330 150 150 100 2.2K 5% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R405 R406 R407 R408 R409 1-216-651-11 1-216-025-91 1-216-057-00 1-216-057-00 1-216-089-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 100 2.2K 2.2K 47K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R532 R533 R534 R535 R536 1-216-057-00 1-216-061-00 1-216-069-00 1-216-057-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 2.2K 3.3K 6.8K 2.2K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R410 R411 R412 R413 R414 1-216-025-91 1-216-057-00 1-216-643-11 1-216-025-91 1-216-057-00 RES,CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 100 2.2K 470 100 2.2K 5% 5% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R537 R538 R541 R542 R543 1-216-025-91 1-216-051-00 1-216-057-00 1-216-057-00 1-216-061-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.2K 2.2K 2.2K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R415 R416 R417 R418 R419 1-216-643-11 1-216-025-91 1-216-057-00 1-216-057-00 1-216-085-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470 100 2.2K 2.2K 33K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R544 R545 R546 R547 R548 1-216-069-00 1-216-057-00 1-216-057-00 1-216-025-91 1-216-051-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 6.8K 2.2K 2.2K 100 1.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R420 R421 R422 R423 R424 1-216-025-91 1-216-651-11 1-216-025-91 1-216-025-91 1-216-643-11 RES,CHIP METAL CHIP RES,CHIP RES,CHIP METAL CHIP 100 1K 100 100 470 5% 0.50% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R425 R426 R427 R428 R429 1-216-643-11 1-216-025-91 1-216-651-11 1-216-057-00 1-216-057-00 METAL CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 470 100 1K 2.2K 2.2K 0.50% 5% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R430 R431 R432 R433 R434 1-216-025-91 1-216-025-91 1-216-061-00 1-216-075-00 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 3.3K 12K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R435 R436 R437 R438 R439 1-216-051-00 1-216-065-91 1-216-057-00 1-216-073-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1.2K 4.7K 2.2K 10K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R440 R441 R442 R443 R444 1-216-049-91 1-216-295-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP SHORT RES,CHIP RES,CHIP RES,CHIP 1K 0 100 100 100 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R501 R502 R503 R504 R505 1-216-025-91 1-216-057-00 1-216-651-11 1-216-651-11 1-216-025-91 RES,CHIP RES,CHIP METAL CHIP METAL CHIP RES,CHIP 100 2.2K 1K 1K 100 5% 5% 0.50% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R506 R507 R508 R509 R510 1-216-025-91 1-216-057-00 1-216-025-91 1-216-037-00 1-216-631-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 100 2.2K 100 330 150 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R511 R512 R513 R514 1-216-631-11 1-216-025-91 1-216-025-91 1-216-057-00 METAL CHIP RES,CHIP RES,CHIP RES,CHIP 150 100 100 2.2K 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 9-8 **************************************************************** * A-1131-464-A B2 MOUNT *********** C3901 C3902 C3903 C3904 C3905 1-163-031-11 1-164-161-11 1-163-133-00 1-163-017-00 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.0022µF 10% 470PF 5% 0.0047µF 10% 0.001µF 10% 50V 50V 50V 50V 50V C3906 C3907 C3908 C3909 C3910 1-163-251-11 1-163-133-00 1-164-346-11 1-163-259-91 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 470PF 1µF 220PF 0.01µF 5% 5% 50V 50V 16V 50V 50V C3912 C3913 C3914 C3915 C3916 1-163-127-00 1-163-031-11 1-163-031-11 1-163-259-91 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 270PF 0.01µF 0.01µF 220PF 0.01µF 5% C3917 C3918 C3919 C3920 C3921 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-164-489-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.22µF C3922 C3923 C3924 1-164-489-11 CERAMIC CHIP 0.22µF 1-163-031-11 CERAMIC CHIP 0.01µF 1-163-031-11 CERAMIC CHIP 0.01µF 5% 5% 10% 10% 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 50V 50V CN3901 * 1-573-896-11 SOCKET, CONNECTOR 12P CN3902 * 1-573-896-11 SOCKET, CONNECTOR 12P BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B2 BX Ref.No. Part No. Description Remark D3901 D3902 D3903 D3904 8-719-016-74 8-719-016-74 8-719-016-74 8-719-016-74 DIODE 1SS352 DIODE 1SS352 DIODE 1SS352 DIODE 1SS352 IC3901 IC3902 IC3904 IC3905 IC3906 8-759-239-34 8-759-523-02 8-759-239-34 8-759-100-96 8-759-234-20 IC TC74HC4538AF IC TC74HC4053AFT(EL) IC TC74HC4538AF IC UPC4558G2 IC TC7S08F IC3907 IC3908 8-759-035-90 IC SC7S02F 8-759-082-61 IC TC4W53FU Ref.No. Part No. Description Remark R3933 R3934 R3935 R3936 R3937 1-216-651-11 1-216-025-91 1-216-049-91 1-216-097-91 1-216-025-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 100 1K 100K 100 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3938 R3939 R3940 R3941 R3942 1-216-073-00 1-216-097-91 1-216-073-00 1-216-049-91 1-216-081-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 100K 10K 1K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3943 R3944 R3945 R3946 R3947 1-216-055-00 1-216-049-91 1-216-079-00 1-216-059-00 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1.8K 1K 18K 2.7K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3948 1-216-295-91 SHORT 0 Q3901 Q3902 Q3903 Q3905 Q3906 8-729-027-38 8-729-027-38 8-729-026-50 8-729-026-50 8-729-027-38 TRANSISTOR DTA144EKA-T146 TRANSISTOR DTA144EKA-T146 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR DTA144EKA-T146 Q3907 Q3908 Q3909 Q3910 Q3911 8-729-120-28 8-729-026-50 8-729-026-50 8-729-026-50 1-801-806-11 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR DTC144EKA-T146 Q3912 Q3913 Q3914 Q3915 Q3916 8-729-202-38 8-729-202-38 8-729-120-28 8-729-026-50 8-729-120-28 TRANSISTOR 2SC3326N-A TRANSISTOR 2SC3326N-A TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-QR TRANSISTOR 2SC1623-L5L6 **************************************************************** * A-1136-013-A BX COMPL *********** C010 C011 C012 C013 C014 1-128-526-11 1-163-038-91 1-128-526-11 1-163-038-91 1-128-526-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT 100µF 0.1µF 100µF 0.1µF 100µF 20% C015 C016 C017 C018 C019 1-163-038-91 1-163-038-91 1-163-038-91 1-163-038-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF 25V 25V 25V 25V 25V C020 C021 C022 C050 C051 1-163-038-91 1-163-038-91 1-163-038-91 1-128-526-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.1µF 0.1µF 0.1µF 100µF 0.1µF 25V 25V 25V 16V 25V C052 C053 C054 C055 C056 1-128-526-11 1-163-038-91 1-128-526-11 1-163-038-91 1-163-038-91 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 100µF 0.1µF 100µF 0.1µF 0.1µF C057 C058 C059 C060 C061 1-163-038-91 1-163-038-91 1-163-038-91 1-163-038-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.1µF 0.1µF 0.1µF 0.1µF C062 C101 C102 C103 C104 1-163-038-91 1-163-227-11 1-163-235-11 1-107-701-11 1-107-725-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.1µF 10PF 22PF 47µF 0.1µF 0.5PF 5% 20% 10% 25V 50V 50V 16V 16V C106 C201 C202 C203 C204 1-163-021-91 1-163-227-11 1-163-235-11 1-107-701-11 1-107-725-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 10PF 22PF 47µF 0.1µF 10% 0.5PF 5% 20% 10% 50V 50V 50V 16V 16V C206 C301 C302 C303 C304 1-163-021-91 1-163-227-11 1-163-235-11 1-107-701-11 1-107-725-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 10PF 22PF 47µF 0.1µF 10% 0.5PF 5% 20% 10% 50V 50V 50V 16V 16V 20% 20% 16V 25V 16V 25V 16V R3901 R3902 R3903 R3904 R3905 1-216-025-91 1-216-025-91 1-216-659-11 1-216-025-91 1-218-754-11 RES,CHIP RES,CHIP METAL CHIP RES,CHIP METAL CHIP 100 100 2.2K 100 120K 5% 5% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3906 R3907 R3908 R3909 R3910 1-216-659-11 1-218-754-11 1-216-059-00 1-216-659-11 1-216-699-91 METAL CHIP METAL CHIP RES,CHIP METAL CHIP METAL CHIP 2.2K 120K 2.7K 2.2K 100K 0.50% 0.50% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3912 R3913 R3914 R3915 R3916 1-216-057-00 1-216-655-11 1-216-025-91 1-216-674-11 1-216-025-91 RES,CHIP METAL CHIP RES,CHIP METAL CHIP RES,CHIP 2.2K 1.5K 100 9.1K 100 5% 0.50% 5% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R3917 R3918 R3919 R3920 R3922 1-216-097-91 1-216-049-91 1-216-065-91 1-216-049-91 1-216-689-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 100K 1K 4.7K 1K 39K 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3923 R3924 R3925 R3926 R3927 1-216-025-91 1-216-681-11 1-216-697-91 1-216-049-91 1-216-699-91 RES,CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 100 18K 82K 1K 100K 5% 0.50% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R3928 R3929 R3930 R3931 R3932 1-216-025-91 1-216-681-11 1-216-675-91 1-216-049-91 1-216-653-11 RES,CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 100 18K 10K 1K 1.2K 5% 0.50% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 20% 20% 20% 16V 25V 16V 25V 25V 25V 25V 25V 25V 25V 9-9 BX Ref.No. Part No. Description Remark C306 C401 C402 C403 C404 1-163-021-91 1-163-091-00 1-163-235-11 1-107-701-11 1-107-725-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP C501 C502 C503 1-128-526-11 ELECT 100µF 1-163-038-91 CERAMIC CHIP 0.1µF 1-163-038-91 CERAMIC CHIP 0.1µF 0.01µF 8PF 22PF 47µF 0.1µF 10% 0.25PF 5% 20% 10% 50V 50V 50V 16V 16V 20% 16V 25V 25V CN001 * 1-774-523-11 PIN, CONNECTOR (PC BOARD) 64P D101 D102 D201 D202 D301 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D302 D401 D402 D501 8-719-073-01 8-719-073-01 8-719-073-01 8-719-158-19 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD6.2SB FL501 FL502 FL503 1-239-183-11 FILTER, EMI 1-239-480-11 FILTER, EMI 1-239-480-11 FILTER, EMI IC010 IC050 IC501 IC502 IC503 8-759-460-74 8-759-539-89 8-759-594-41 8-759-186-44 8-759-156-54 IC BA05FP-E2 IC LM2990SX-5.0 IC MB89613R-651 IC TC74VHC125F IC X25040SI Q101 Q102 Q103 Q201 Q202 8-729-112-65 8-729-027-38 8-729-107-31 8-729-112-65 8-729-027-38 TRANSISTOR 2SA1462-Y33 TRANSISTOR DTA144EKA-T146 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-Y33 TRANSISTOR DTA144EKA-T146 Q203 Q301 Q302 Q303 Q401 8-729-107-31 8-729-112-65 8-729-027-38 8-729-107-31 8-729-120-28 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SA1462-Y33 TRANSISTOR DTA144EKA-T146 TRANSISTOR 2SC3545-T43 TRANSISTOR 2SC1623-L5L6 Q402 Q403 Q404 Q501 1-801-806-11 8-729-026-49 8-729-027-38 1-801-806-11 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR DTA144EKA-T146 TRANSISTOR DTC144EKA-T146 Description Remark R109 R201 1-216-013-00 RES,CHIP 1-214-837-11 METAL 33 75 5% 1% 1/10W 1/2W R202 R203 R204 R205 R206 1-216-089-91 1-216-025-91 1-216-057-00 1-216-097-91 1-216-009-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 100 2.2K 100K 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R207 R208 R209 R301 R302 1-216-025-91 1-216-097-91 1-216-013-00 1-214-837-11 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP METAL RES,CHIP 100 100K 33 75 47K 5% 5% 5% 1% 5% 1/10W 1/10W 1/10W 1/2W 1/10W R303 R304 R305 R306 R307 1-216-025-91 1-216-057-00 1-216-097-91 1-216-009-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 2.2K 100K 22 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R308 R309 R401 R402 R403 1-216-097-91 1-216-013-00 1-214-837-11 1-216-089-91 1-216-049-91 RES,CHIP RES,CHIP METAL RES,CHIP RES,CHIP 100K 33 75 47K 1K 5% 5% 1% 5% 5% 1/10W 1/10W 1/2W 1/10W 1/10W R404 R405 R406 R407 R408 1-216-097-91 1-216-057-00 1-216-009-91 1-216-025-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 2.2K 22 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R409 R410 R501 R502 R503 1-216-013-00 1-216-097-91 1-216-097-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 100K 100K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R504 R505 R506 R507 R508 1-216-097-91 1-216-025-91 1-216-097-91 1-216-025-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100 100K 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R509 R510 R511 R512 R513 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R514 R515 R516 R517 R518 1-216-097-91 1-216-097-91 1-216-065-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 4.7K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W TB001 1-694-601-11 TERMINAL BOARD ASSY, I/O TP001 TP010 R101 R102 R103 R104 R105 1-214-837-11 1-216-089-91 1-216-025-91 1-216-057-00 1-216-097-91 METAL RES,CHIP RES,CHIP RES,CHIP RES,CHIP 75 47K 100 2.2K 100K 1% 5% 5% 5% 5% 1/2W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 1-216-009-91 RES,CHIP 1-216-025-91 RES,CHIP 1-216-097-91 RES,CHIP 22 100 100K 5% 5% 5% 1/10W 1/10W 1/10W 9-10 Ref.No. Part No. * 1-537-864-11 PIN, POST * 1-537-864-11 PIN, POST X501 1-578-689-21 VIBRATOR ( 8 MHz) **************************************************************** BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A C Ref.No. Part No. Description Remark Ref.No. Part No. D777 D778 * A-1331-883-A C MOUNT ********** 4-373-933-01 SHEET (TRANSISTOR), BN 4-382-854-11 SCREW (M3X10), P, SW (+) J701 1-107-963-11 1-162-116-00 1-136-627-11 1-162-114-00 1-102-110-00 ELECT CERAMIC FILM CERAMIC CERAMIC 33µF 680PF 0.022µF 4700PF 220PF 20% 10% 3% C731 C732 C733 C734 C735 1-107-888-11 1-163-031-11 1-163-031-11 1-107-963-11 1-102-050-00 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC 47µF 0.01µF 0.01µF 33µF 0.01µF 20% C750 C751 C752 C753 C754 1-102-110-00 1-107-888-11 1-163-031-11 1-163-031-11 1-107-963-11 CERAMIC ELECT CERAMIC CHIP CERAMIC CHIP ELECT 220PF 47µF 0.01µF 0.01µF 33µF 10% 20% C755 C770 C771 C772 C773 1-102-050-00 1-102-110-00 1-107-888-11 1-163-031-11 1-163-031-11 CERAMIC CERAMIC ELECT CERAMIC CHIP CERAMIC CHIP 0.01µF 220PF 47µF 0.01µF 0.01µF 99% 10% 20% C774 C775 C777 C778 1-107-963-11 1-102-050-00 1-102-514-11 1-102-518-11 ELECT CERAMIC CERAMIC CERAMIC 33µF 0.01µF 22PF 33PF 20% 99% 5% 5% 10% 20% 99% 20% 250V 2KV 1KV 2KV 50V 25V 50V 50V 250V 500V 50V 25V 50V 50V 250V 500V 50V 25V 50V 50V 250V 500V 50V 50V D730 D731 D732 D733 D734 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D735 D736 D737 D738 D750 8-719-073-01 8-719-073-01 8-719-073-01 8-719-157-72 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD22M-B DIODE MA111-(K8).S0 D751 D752 D753 D754 D755 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D756 D757 D758 D770 D771 8-719-073-01 8-719-073-01 8-719-157-72 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD22M-B DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D772 D773 D774 D775 D776 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 8-719-073-01 DIODE MA111-(K8).S0 8-719-157-72 DIODE RD22M-B ! 1-251-116-11 SOCKET, CRT L701 L730 L750 L770 1-412-532-11 1-408-597-31 1-408-597-31 1-408-597-31 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 39µH 3.3µH 3.3µH 3.3µH Q701 Q730 Q731 Q732 Q733 8-729-903-68 8-729-809-22 8-729-821-02 8-729-801-88 8-729-821-02 TRANSISTOR 2SD982 TRANSISTOR 2SC3950-D TRANSISTOR 2SC3503-DE TRANSISTOR 2SA1381-E TRANSISTOR 2SC3503-DE Q734 Q735 Q750 Q751 Q752 8-729-033-31 8-729-105-08 8-729-809-22 8-729-821-02 8-729-801-88 TRANSISTOR 2SK520K44K45-T1B TRANSISTOR 2SA1330-06 TRANSISTOR 2SC3950-D TRANSISTOR 2SC3503-DE TRANSISTOR 2SA1381-E Q753 Q754 Q755 Q770 Q771 8-729-821-02 8-729-033-31 8-729-105-08 8-729-809-22 8-729-821-02 TRANSISTOR 2SC3503-DE TRANSISTOR 2SK520K44K45-T1B TRANSISTOR 2SA1330-06 TRANSISTOR 2SC3950-D TRANSISTOR 2SC3503-DE Q772 Q773 Q774 Q775 8-729-801-88 8-729-821-02 8-729-033-31 8-729-105-08 TRANSISTOR 2SA1381-E TRANSISTOR 2SC3503-DE TRANSISTOR 2SK520K44K45-T1B TRANSISTOR 2SA1330-06 CN701 * 1-691-096-11 PIN, CONNECTOR (PC BOARD) 8P CN702 * 1-564-525-11 PLUG, CONNECTOR 10P CN703 1-695-915-11 TAB (CONTACT) Remark C701 C702 C703 C704 C730 Description R701 R702 R703 R704 R705 1-249-383-11 1-249-428-11 1-216-017-91 1-216-097-91 1-216-073-00 CARBON CARBON RES,CHIP RES,CHIP RES,CHIP 1.5 8.2K 47 100K 10K 5% 5% 5% 5% 5% 1/4W F 1/4W F 1/10W 1/10W 1/10W R706 R707 R708 R731 R732 1-216-065-91 1-219-752-11 1-220-824-11 1-216-025-91 1-214-844-81 RES,CHIP CARBON CARBON RES,CHIP METAL 4.7K 100K 270K 100 150 5% 5% 5% 5% 1% 1/10W 1/2W 1/2W 1/10W 1/2W R733 R734 R735 R736 R737 1-215-381-00 1-219-688-11 1-216-017-91 1-216-017-91 1-215-892-11 METAL METAL RES,CHIP RES,CHIP METAL OXIDE 22 2.7K 47 47 1K 1% 1% 5% 5% 5% 1/4W 10W 1/10W 1/10W 2W F R738 R739 R741 R742 R743 1-216-013-00 1-216-013-00 1-216-689-11 1-216-085-00 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 33 39K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R744 R745 R746 R751 R752 1-216-033-00 1-219-744-11 1-219-747-91 1-216-025-91 1-214-844-81 RES,CHIP CARBON CARBON RES,CHIP METAL 220 220 2.2K 100 150 5% 5% 5% 5% 1% 1/10W 1/2W 1/2W 1/10W 1/2W R753 R754 R755 1-215-381-00 METAL 1-219-688-11 METAL 1-216-017-91 RES,CHIP 22 2.7K 47 1% 1% 5% 1/4W 10W 1/10W 9-11 C G Ref.No. Part No. Description Remark R756 R757 1-216-017-91 RES,CHIP 1-215-892-11 METAL OXIDE 47 1K 5% 5% 1/10W 2W F R758 R759 R761 R762 R763 1-216-013-00 1-216-013-00 1-216-689-11 1-216-085-00 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 33 39K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R764 R765 R766 R771 R772 1-216-033-00 1-219-744-11 1-219-747-91 1-216-025-91 1-214-844-81 RES,CHIP CARBON CARBON RES,CHIP METAL 220 220 2.2K 100 150 5% 5% 5% 5% 1% 1/10W 1/2W 1/2W 1/10W 1/2W R773 R774 R775 R776 R777 1-215-381-00 1-219-688-11 1-216-017-91 1-216-017-91 1-215-892-11 METAL METAL RES,CHIP RES,CHIP METAL OXIDE 22 2.7K 47 47 1K 1% 1% 5% 5% 5% 1/4W 10W 1/10W 1/10W 2W F R778 R779 R781 R782 R783 1-216-013-00 1-216-013-00 1-216-689-11 1-216-085-00 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33 33 39K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R784 R785 R786 R788 1-216-033-00 1-219-744-11 1-219-747-91 1-202-816-11 RES,CHIP CARBON CARBON SOLID 220 220 2.2K 68K 5% 5% 5% 10% 1/10W 1/2W 1/2W 1/2W RV701 ! 1-241-714-11 RES, ADJ, METAL FILM 110M RV702 1-230-641-11 RES, ADJ, METAL GLAZE 2.2M SG701 SG702 SG703 SG704 SG705 1-519-422-11 1-519-422-11 1-519-422-11 1-519-422-11 1-519-422-11 GAP, SPARK GAP, SPARK GAP, SPARK GAP, SPARK GAP, SPARK **************************************************************** * A-1316-456-A G COMPL ********** ! 1-473-159-21 1-533-223-11 1-900-249-01 ! 2-371-561-00 ! 4-061-191-01 CAP ASSY, HIGH-VOLTAGE CLIP, FUSE LEAD ASSY, FOCUS BUSHING (P), INSULATING SHEET, INSULATE 4-382-854-01 SCREW (M3X8), P, SW (+) 7-682-949-09 SCREW +PSW 3X10 C501 C502 C503 C504 C505 1-163-275-11 1-163-251-11 1-107-889-11 1-163-031-11 1-107-561-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP FILM CHIP 0.001µF 100PF 220µF 0.01µF 0.01µF C507 C508 C509 C510 C511 1-107-889-11 1-163-017-00 1-163-275-11 1-115-565-11 1-163-021-91 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220µF 20% 0.0047µF 10% 0.001µF 5% 2.2µF 10% 0.01µF 10% 9-12 5% 5% 20% 5% 50V 50V 25V 50V 50V 25V 50V 50V 10V 50V Ref.No. Part No. Description Remark C512 C513 C514 C515 C516 1-126-964-11 1-126-968-11 1-163-017-00 1-163-021-91 1-126-959-11 ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT 10µF 20% 100µF 20% 0.0047µF 10% 0.01µF 10% 0.47µF 20% 50V 50V 50V 50V 50V C517 C518 C519 C520 C521 1-163-037-11 1-126-967-11 1-163-021-91 1-163-009-11 1-164-222-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022µF 47µF 0.01µF 0.001µF 0.22µF 50V 50V 50V 50V 25V C522 C523 C524 C525 C526 1-164-346-11 1-163-139-00 1-163-021-91 1-164-489-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1µF 820PF 0.01µF 0.22µF 0.47µF C527 C528 C529 C530 C531 1-126-968-11 1-163-031-11 1-163-021-91 1-126-968-11 1-164-344-11 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 100µF 0.01µF 0.01µF 100µF 0.068µF 10% 20% 10% 50V 50V 50V 50V 25V C534 C536 C537 C538 C539 C546 1-124-234-00 1-126-967-11 1-163-038-91 1-102-119-00 1-163-023-00 1-163-031-11 ELECT ELECT CERAMIC CHIP CERAMIC CERAMIC CHIP CERAMIC CHIP 22µF 20% 47µF 20% 0.1µF 0.0015µF 10% 0.015µF 10% 0.01µF 16V 50V 25V 50V 50V 50V C547 C548 C549 C550 C551 1-164-161-11 1-126-967-11 1-126-964-11 1-163-021-91 1-163-021-91 CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP 0.0022µF 10% 47µF 20% 10µF 20% 0.01µF 10% 0.01µF 10% 50V 50V 50V 50V 50V C552 C553 C554 C555 C556 1-126-964-11 1-163-021-91 1-126-960-11 1-163-038-91 1-163-021-91 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP 10µF 0.01µF 1µF 0.1µF 0.01µF 20% 10% 20% 10% 50V 50V 50V 25V 50V C557 C558 C559 C560 C561 1-163-021-91 1-126-964-11 1-163-021-91 1-126-960-11 1-163-001-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 10µF 0.01µF 1µF 220PF 10% 20% 10% 20% 10% 50V 50V 50V 50V 50V C562 C563 C564 C565 C566 1-107-725-11 1-163-037-11 1-163-031-11 1-164-004-11 1-163-093-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1µF 0.022µF 0.01µF 0.1µF 10PF 10% 10% 16V 50V 50V 25V 50V C567 C568 C569 C570 C571 1-163-021-91 1-106-383-00 1-102-820-00 1-123-024-21 1-162-116-00 CERAMIC CHIP MYLAR CERAMIC ELECT CERAMIC 0.01µF 0.047µF 330PF 33µF 680PF C573 C574 C575 C576 C577 1-136-044-00 1-107-682-11 1-102-030-00 1-136-541-11 1-137-417-11 FILM CERAMIC CHIP CERAMIC FILM MYLAR 0.0017µF 3% 1µF 10% 330PF 10% 1.5µF 5% 0.0047µF 10% 1.6KV 16V 500V 200V 200V C578 C581 C582 C585 C587 1-162-114-00 1-163-021-91 1-163-021-91 1-126-968-11 1-107-725-11 CERAMIC CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.0047µF 0.01µF 10% 0.01µF 10% 100µF 20% 0.1µF 10% 2KV 50V 50V 50V 16V C588 C589 C590 C591 C592 1-163-031-11 1-107-364-11 1-107-364-11 1-163-031-11 1-163-031-11 CERAMIC CHIP MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 200V 200V 50V 50V 10% 20% 10% 10% 5% 10% 10% 10% 20% 10% 5% 10% 10% 5% 10% 10% 10% 16V 50V 50V 16V 16V 50V 200V 50V 160V 2KV BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G Ref.No. Part No. Description Remark Ref.No. Part No. Description C593 C594 C595 C596 C598 1-163-031-11 1-163-031-11 1-104-652-11 1-163-031-11 1-107-877-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT 0.01µF 0.01µF 470µF 0.01µF 1000µF 50V 50V 10V 50V 10V C685 C687 C688 C689 C690 1-162-318-11 1-104-665-11 1-102-129-00 1-104-652-11 1-104-652-11 CERAMIC ELECT CERAMIC ELECT ELECT 0.001µF 100µF 0.01µF 470µF 470µF 10% 20% 10% 20% 20% 500V 10V 50V 10V 10V C599 C602 C603 C604 C606 1-163-031-11 ! 1-113-889-11 1-164-004-11 ! 1-107-533-11 ! 1-113-926-11 CERAMIC CHIP CERAMIC CERAMIC CHIP MYLAR CERAMIC 0.01µF 1000PF 20% 0.1µF 10% 1µF 20% 0.0047µF 50V 250V 25V 250V 250V C1500 C1503 C1505 C1506 C1507 1-163-031-11 1-163-133-00 1-104-555-11 1-163-021-91 1-163-021-91 CERAMIC CHIP CERAMIC CHIP FILM CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 470PF 0.022µF 0.01µF 0.01µF 5% 5% 10% 10% 50V 50V 16V 50V 50V C607 C608 C609 C610 C611 ! 1-113-926-11 ! 1-113-889-11 1-163-021-91 1-107-910-11 1-137-479-11 CERAMIC CERAMIC CERAMIC CHIP ELECT MYLAR 0.0047µF 1000PF 20% 0.01µF 10% 100µF 20% 1µF 10% 250V 250V 50V 50V 400V C1508 C1511 C1512 C1513 C1514 1-107-823-11 1-163-038-91 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47µF 0.1µF 0.01µF 0.01µF 0.01µF 10% C612 C613 C614 C615 C616 1-107-906-11 1-136-175-11 1-107-909-11 1-117-752-11 1-163-021-91 ELECT FILM ELECT ELECT(BLOCK) CERAMIC CHIP 10µF 0.68µF 47µF 330µF 0.01µF 20% 5% 20% 20% 10% 50V 50V 50V 450V 50V C1515 C1516 C1517 C1518 C1519 1-163-227-11 1-163-038-91 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10PF 0.1µF 0.01µF 0.01µF 0.01µF 0.5PF 50V 25V 50V 50V 50V C617 C621 C623 C624 C625 1-107-906-11 1-107-905-11 1-137-399-11 1-130-029-00 1-107-906-11 ELECT ELECT MYLAR FILM ELECT 10µF 4.7µF 0.1µF 8200PF 10µF 20% 20% 5% 2% 20% 50V 50V 100V 50V 50V C1520 C1521 C1522 C1523 C1524 1-163-009-11 1-163-809-11 1-107-682-11 1-107-823-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.047µF 1µF 0.47µF 0.47µF 10% 10% 10% 10% 10% 50V 25V 16V 16V 16V C627 C629 C631 C636 C637 1-107-910-11 1-119-867-11 1-119-867-11 1-107-890-11 1-111-171-31 ELECT MYLAR MYLAR ELECT ELECT 100µF 0.047µF 0.047µF 2200µF 220µF 20% 3% 3% 20% 20% 50V 1KV 1KV 25V 100V C1525 C1526 C1527 C1528 C1530 1-163-021-91 1-163-009-11 1-163-227-11 1-126-935-11 1-163-005-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 0.001µF 10PF 470µF 470PF 10% 10% 0.5PF 20% 10% 50V 50V 50V 6.3V 50V C638 C640 C641 C642 C643 1-111-171-31 1-107-911-11 1-107-890-11 1-107-890-11 1-107-890-11 ELECT ELECT ELECT ELECT ELECT 220µF 220µF 2200µF 2200µF 2200µF 20% 20% 20% 20% 20% 100V 50V 25V 25V 25V C1531 C1532 C1533 C1534 C1535 1-163-005-11 1-104-664-11 1-163-021-91 1-163-021-91 1-163-038-91 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 47µF 0.01µF 0.01µF 0.1µF 10% 20% 10% 10% 50V 16V 50V 50V 25V C644 C645 C648 C649 C650 1-107-890-11 1-107-960-11 1-107-962-11 1-107-914-11 1-107-914-11 ELECT ELECT ELECT ELECT ELECT 2200µF 4.7µF 22µF 1000µF 1000µF 20% 20% 20% 20% 20% 25V 200V 250V 25V 25V C1536 C1537 C1538 C1539 C1540 1-163-009-11 1-163-021-91 1-163-009-11 1-126-964-11 1-126-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 0.001µF 0.01µF 0.001µF 10µF 10µF 10% 10% 10% 20% 20% 50V 50V 50V 50V 50V C651 C652 C653 C654 C661 1-107-914-11 1-107-914-11 1-107-906-11 1-107-906-11 1-107-906-11 ELECT ELECT ELECT ELECT ELECT 1000µF 1000µF 10µF 10µF 10µF 20% 20% 20% 20% 20% 25V 25V 50V 50V 50V C1541 C2501 C2502 C2503 C2504 1-126-963-11 1-163-021-91 1-162-558-11 1-126-968-11 1-164-004-11 ELECT CERAMIC CHIP CERAMIC ELECT CERAMIC CHIP 4.7µF 0.01µF 100PF 100µF 0.1µF 20% 10% 10% 20% 10% 50V 50V 2KV 50V 25V C662 C663 C664 C665 C666 1-107-888-11 1-107-888-11 1-107-888-11 1-107-888-11 1-107-906-11 ELECT ELECT ELECT ELECT ELECT 47µF 47µF 47µF 47µF 10µF 20% 20% 20% 20% 20% 25V 25V 25V 25V 50V C2505 C2506 C2507 C2508 C2509 1-163-021-91 1-106-383-00 1-163-021-91 1-123-024-21 1-163-021-91 CERAMIC CHIP MYLAR CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 0.047µF 0.01µF 33µF 0.01µF 10% 10% 10% 10% 50V 200V 50V 160V 50V C667 C669 C670 C671 C674 1-163-021-91 1-163-021-91 1-107-907-11 1-163-021-91 1-102-973-00 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC 0.01µF 0.01µF 22µF 0.01µF 100PF 10% 10% 20% 10% 5% 50V 50V 50V 50V 50V C2510 C2511 C2512 C2513 C2514 1-126-972-11 1-126-972-11 1-102-820-00 1-126-968-11 1-162-558-11 ELECT ELECT CERAMIC ELECT CERAMIC 1000µF 1000µF 330PF 100µF 100PF 20% 20% 5% 20% 10% 50V 50V 50V 50V 2KV C675 C676 C677 C678 C679 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001µF 0.001µF 0.001µF 0.001µF 0.001µF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C2515 C2516 C2518 C2519 C2520 1-130-061-91 1-106-220-00 1-137-194-81 1-163-037-11 1-136-155-00 FILM MYLAR MYLAR CERAMIC CHIP MYLAR 0.0015µF 5% 0.1µF 10% 0.47µF 5% 0.022µF 10% 0.015µF 5% 630V 100V 50V 50V 50V C680 C681 C682 C683 C684 1-163-009-11 1-163-009-11 1-163-009-11 1-162-318-11 1-162-318-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CERAMIC 0.001µF 0.001µF 0.001µF 0.001µF 0.001µF 10% 10% 10% 10% 10% 50V 50V 50V 500V 500V C2521 C2522 C2523 C2524 C2528 1-107-914-11 1-106-351-00 1-126-767-11 1-126-767-11 1-136-044-00 ELECT MYLAR ELECT ELECT FILM 1000µF 20% 0.0022µF 99% 1000µF 20% 1000µF 20% 0.0017µF 3% 50V 200V 16V 16V 1.6KV BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 20% 20% Remark 16V 25V 50V 50V 50V 9-13 G Ref.No. Part No. Description Remark C2529 C2530 C2531 C2532 C2533 1-107-962-11 1-136-044-00 1-162-115-00 1-109-844-11 1-115-521-11 ELECT FILM CERAMIC FILM FILM 22µF 20% 0.0017µF 3% 330PF 10% 0.68µF 5% 0.82µF 5% 250V 1.6KV 2KV 250V 250V D602 D603 D604 D605 D606 ! 8-719-510-53 8-719-037-54 8-719-028-72 8-719-110-31 8-719-911-19 C2534 C2536 C2537 C2538 C2539 1-163-021-91 1-117-677-11 1-104-760-11 1-164-004-11 1-164-346-11 CERAMIC CHIP FILM CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 3.3µF 0.047µF 0.1µF 1µF 10% 5% 10% 10% 50V 250V 50V 25V 16V D607 D608 D609 D612 D614 8-719-073-01 8-719-110-67 8-719-073-01 8-719-989-76 8-719-989-21 DIODE MA111-(K8).S0 DIODE RD27ESB2 DIODE MA111-(K8).S0 DIODE SC802-04 DIODE SC311-6-TE12RA C2541 C2542 C2543 C2544 1-107-957-11 1-162-115-00 1-117-677-11 1-117-214-11 ELECT CERAMIC FILM CERAMIC 1µF 330PF 3.3µF 0.001 20% 10% 5% 10% 250V 2KV 250V 2KV D617 D619 D620 D622 D623 8-719-037-23 8-719-073-01 8-719-073-01 8-719-027-43 8-719-050-18 DIODE RD12SB1-T1 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE S2L20UF DIODE D4SBL20U D624 D625 D626 D627 D630 8-719-052-91 8-719-052-91 8-719-052-90 8-719-110-48 8-719-073-01 DIODE D4SBS4-F DIODE D4SBS4-F DIODE D1NL40-TA2 DIODE RD18ESB1 DIODE MA111-(K8).S0 D633 D634 D635 D636 D637 8-719-073-01 8-719-109-93 8-719-304-63 8-719-989-21 8-719-510-48 DIODE MA111-(K8).S0 DIODE RD6.2ESB2 DIODE RM11C DIODE SC311-6-TE12RA DIODE D1N20R D638 D639 D640 D2501 D2502 8-719-037-06 8-719-073-01 8-719-157-94 8-719-036-96 8-719-929-15 DIODE RD7.5SB1-T1 DIODE MA111-(K8).S0 DIODE RD3.3SB DIODE RD5.6SB2 DIODE HZS9.1NB2 D2503 D2504 D2506 D2507 D2508 8-719-036-96 8-719-908-03 8-719-939-07 8-719-911-19 8-719-988-11 DIODE RD5.6SB2 DIODE GP08D DIODE ERD38-06 DIODE 1SS119-25 DIODE FE3D D2509 D2510 D2511 D2512 D2513 8-719-988-11 8-719-300-76 8-719-075-44 8-719-911-19 8-719-908-03 DIODE FE3D DIODE RH-1A DIODE DD54SCLS-YCC-11 DIODE 1SS119-25 DIODE GP08D D2514 D2515 D2520 8-719-951-30 DIODE ERA91-02 8-719-158-17 DIODE RD5.6SB2 8-719-989-21 DIODE SC311-6-TE12RA CN501 CN502 CN601 CN602 CN603 * 1-564-515-11 * 1-564-510-11 * 1-766-241-11 * 1-695-561-11 * 1-691-960-11 PLUG, CONNECTOR 12P PLUG, CONNECTOR 7P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (PC BOARD) 7P PIN, CONNECTOR (PC BOARD) 3P CN604 CN605 CN606 CN607 CN608 * 1-691-096-11 * 1-564-509-11 * 1-564-511-11 * 1-691-291-11 * 9-910-999-31 PIN, CONNECTOR (PC BOARD) 8P PLUG, CONNECTOR 6P PLUG, CONNECTOR 8P PIN, CONNECTOR 5P H TYPE BASE POST CN2501 * 1-568-536-11 PLUG (MINIATURE DY) 6P Ref.No. Part No. Description Remark DIODE D4SB60L DIODE RD30SB-T1 DIODE RGP02-17EL-6433 DIODE RD12ESB2 DIODE 1SS119-25 D501 D502 D503 D504 D505 8-719-073-01 8-719-073-01 8-719-073-01 8-719-158-56 8-719-037-23 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD15SB1 DIODE RD12SB1-T1 D506 D507 D509 D511 D512 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D513 D514 D515 D516 D517 8-719-302-43 8-719-073-01 8-719-073-01 8-719-929-15 8-719-037-23 DIODE EL1Z DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE HZS9.1NB2 DIODE RD12SB1-T1 D518 D519 D520 D524 D525 8-719-988-11 8-719-988-11 8-719-028-72 8-719-110-31 8-719-073-01 DIODE FE3D DIODE FE3D DIODE RGP02-17EL-6433 DIODE RD12ESB2 DIODE MA111-(K8).S0 D528 D529 D530 D531 D532 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D533 D534 D535 D536 D537 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-158-40 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE RD10SB1 D538 D539 D540 D541 D601 8-719-158-53 8-719-158-53 8-719-033-53 8-719-033-53 8-719-073-01 DIODE RD13SB2 DIODE RD13SB2 DIODE RD6.8SB2-T1 DIODE RD6.8SB2-T1 DIODE MA111-(K8).S0 9-14 FB501 FB502 FB606 FB2501 FB2503 1-410-397-21 1-410-397-21 1-410-397-21 1-410-397-21 1-410-397-21 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH IC501 IC502 IC503 IC506 IC507 8-759-981-48 8-759-981-48 8-759-239-34 8-759-981-48 8-759-593-29 IC TL082M IC TL082M IC TC74HC4538AF IC TL082M IC TDA9106 IC508 IC509 IC510 IC512 IC514 8-752-072-94 8-759-239-34 8-759-239-34 8-752-072-94 8-759-198-31 IC CXA1875AM-T4 IC TC74HC4538AF IC TC74HC4538AF IC CXA1875AM-T4 IC µPC1093J IC515 IC516 8-759-158-82 IC CXA1544M-T6 8-759-009-07 IC MC14053BF BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G Ref.No. Part No. IC517 IC519 IC520 Description Remark 8-759-198-31 IC µPC1093J ! 8-759-198-31 IC µPC1093J 8-759-998-98 IC LM358D IC522 IC523 IC524 IC526 IC527 8-759-231-30 8-759-988-13 8-759-424-31 8-759-231-30 8-759-209-69 IC TC-4S30F IC LM393PS IC MC74HC175FEL IC TC-4S30F IC TC4S11F IC528 IC529 IC601 IC602 IC606 8-759-082-55 8-759-239-34 8-749-015-27 8-749-013-78 8-759-394-35 IC TC7W00FU IC TC74HC4538AF IC MZ1540 IC MCR5102 IC BA12T IC607 IC608 IC609 IC610 IC2501 8-759-701-88 8-759-450-47 8-759-247-67 8-749-920-61 8-759-209-90 IC NJM7912FA IC BA05T IC LM2990T-5.0 IC SE-135N IC TC4S71F IC2502 IC2503 IC2504 8-759-100-96 IC UPC4558G2 8-759-980-58 IC TDA8172 8-759-803-42 IC LA6500-FA L501 L502 L503 L601 L603 1-410-482-31 1-412-533-21 1-412-525-31 1-406-976-11 1-412-529-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 100µH 47µH 10µH 68µH 22µH L604 L605 L606 L607 L608 1-412-529-11 1-412-529-11 1-412-529-11 1-406-663-21 1-406-663-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22µH 22µH 22µH 47µH 47µH L609 L610 L613 L614 L615 1-410-397-21 1-410-397-21 1-412-533-21 1-412-533-21 1-412-533-21 FERRITE FERRITE INDUCTOR INDUCTOR INDUCTOR 1.1µH 1.1µH 47µH 47µH 47µH L616 L617 L2501 L2502 L2503 1-412-533-21 1-412-533-21 1-459-111-00 1-410-682-31 1-411-667-11 INDUCTOR 47µH INDUCTOR 47µH INDUCTOR 10mH INDUCTOR 470µH COIL, HORIZONTAL LINEARITY L2504 L2505 L2506 L2507 1-411-667-11 1-412-552-11 1-414-493-41 1-406-671-11 COIL, HORIZONTAL LINEARITY INDUCTOR 2.2mH INDUCTOR 4.7mH INDUCTOR 1mH Ref.No. Part No. Description Remark Q508 Q509 Q510 Q511 Q512 8-729-026-49 8-729-120-28 8-729-140-96 8-729-140-96 8-729-140-97 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SD774-34 TRANSISTOR 2SD774-34 TRANSISTOR 2SB734-34 Q513 Q514 Q517 Q518 Q520 8-729-044-21 8-729-015-28 8-729-018-03 8-729-018-03 8-729-900-53 TRANSISTOR 2SK2655-01R-F165 TRANSISTOR IRFI9630GS TRANSISTOR 2SC4686A TRANSISTOR 2SC4686A TRANSISTOR DTC114EK Q521 Q523 Q524 Q525 Q529 8-729-120-28 1-801-806-11 1-801-806-11 8-729-027-38 1-801-806-11 TRANSISTOR 2SC1623-L5L6 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTA144EKA-T146 TRANSISTOR DTC144EKA-T146 Q530 Q531 Q532 Q533 Q534 1-801-806-11 1-801-806-11 1-801-806-11 8-729-026-49 8-729-027-38 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR DTA144EKA-T146 Q535 Q536 Q601 Q602 Q603 8-729-120-28 8-729-027-38 8-729-120-28 8-729-119-78 8-729-120-28 TRANSISTOR 2SC1623 TRANSISTOR DTA144EKA TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC2785-HFE TRANSISTOR 2SC1623-L5L6 Q604 Q605 Q608 Q609 Q611 8-729-033-26 8-729-029-47 8-729-029-47 8-729-900-53 8-729-033-25 TRANSISTOR DTA114GKAT146 TRANSISTOR DTA143ESA-TP TRANSISTOR DTA143ESA-TP TRANSISTOR DTC114EK TRANSISTOR DTC114GKA Q612 Q613 Q614 Q615 Q616 8-729-033-26 8-729-027-23 8-729-200-17 8-729-120-28 8-729-033-25 TRANSISTOR DTA114GKAT146 TRANSISTOR DTA114EKA-T146 TRANSISTOR 2SA1091-O TRANSISTOR 2SC1623-L5L6 TRANSISTOR DTC114GKA Q617 Q618 Q619 Q620 Q621 8-729-033-26 1-801-806-11 8-729-027-38 1-801-806-11 8-729-900-53 TRANSISTOR DTA114GKAT146 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTA144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC114EK Q622 Q2501 Q2502 Q2503 Q2504 1-801-806-11 8-729-119-78 8-729-119-76 8-729-015-28 8-729-800-32 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SC2785-HFE TRANSISTOR 2SA1175-HFE TRANSISTOR IRFI9630GS TRANSISTOR 2SC2362K-G Q2505 Q2508 Q2511 Q2512 Q2513 8-729-820-73 8-729-049-47 8-729-122-13 1-801-806-11 8-729-119-76 TRANSISTOR 2SC3746 TRANSISTOR 2SC5450-CA TRANSISTOR 2SA1221-K TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SA1175-HFE Q2514 Q2515 Q2518 Q2519 8-729-034-60 1-801-806-11 8-729-034-60 1-801-806-11 TRANSISTOR 2SK2350 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SK2350 TRANSISTOR DTC144EKA-T146 NL501 1-519-526-11 LAMP, NEON PH603 PH604 Q501 Q504 Q505 Q506 Q507 8-749-010-64 PHOTO COUPLER PC123F2 8-749-010-64 PHOTO COUPLER PC123F2 8-729-925-42 8-729-027-23 8-729-026-49 8-729-019-85 8-729-026-50 TRANSISTOR IMT2 TRANSISTOR DTA114EKA-T146 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SC3392-5-TB TRANSISTOR 2SA1037AK-T146-QR BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A R501 R502 R503 R504 R505 1-216-651-11 1-216-683-11 1-216-073-00 1-216-073-00 1-216-085-00 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 1K 22K 10K 10K 33K 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R506 R507 R508 R509 R510 1-216-081-00 1-216-073-00 1-216-045-00 1-216-073-00 1-216-677-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 22K 10K 680 10K 12K 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W 9-15 G Ref.No. Part No. Description Ref.No. Part No. Description R511 R512 R513 R514 R515 1-216-069-00 1-216-073-00 1-216-049-91 1-216-073-00 1-216-001-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 6.8K 10K 1K 10K 10 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R592 R593 R594 R595 R596 1-216-049-91 1-216-081-00 1-216-073-00 1-216-069-00 1-216-001-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 22K 10K 6.8K 10 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R517 R518 R519 R520 R521 1-216-073-00 1-216-073-00 1-216-674-11 1-216-077-91 1-216-059-00 RES,CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 10K 10K 9.1K 15K 2.7K 5% 5% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R597 R599 R601 R602 R603 1-247-688-11 1-216-065-91 1-216-073-00 ! 1-202-844-00 1-260-081-11 CARBON RES,CHIP RES,CHIP SOLID CARBON 10 4.7K 10K 330K 33 5% 5% 5% 20% 5% 1/4W F 1/10W 1/10W 1/2W 1/2W R522 R523 R524 R525 R526 1-216-073-00 1-216-073-00 1-216-025-91 1-216-077-91 1-216-041-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 100 15K 470 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R604 R605 R606 R607 R608 1-215-887-00 1-216-097-91 1-240-251-11 1-216-095-00 1-216-073-00 METAL OXIDE RES,CHIP CMT,MELF RES,CHIP RES,CHIP 150 100K 6.8 82K 10K 5% 5% 5% 5% 5% 2W F 1/10W 10W 1/10W 1/10W R527 R528 R529 R531 R540 1-216-049-91 1-216-073-00 1-216-041-00 1-216-105-91 1-216-075-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 10K 470 220K 12K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R609 R610 R611 R612 R613 1-216-065-91 1-216-049-91 1-207-615-00 1-216-089-91 1-207-615-00 RES,CHIP RES,CHIP METAL RES,CHIP METAL 4.7K 1K 0.33 47K 0.33 5% 5% 10% 5% 10% 1/10W 1/10W 2W 1/10W 2W R542 R543 R544 R545 R546 1-216-025-91 1-216-085-00 1-216-077-91 1-216-685-11 1-216-673-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 100 33K 15K 27K 8.2K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R614 R615 R616 R617 R618 1-216-073-00 1-215-485-00 1-215-485-00 1-215-485-00 1-216-677-11 RES,CHIP METAL METAL METAL METAL CHIP 10K 470K 470K 470K 12K 5% 1% 1% 1% 0.50% 1/10W 1/4W 1/4W 1/4W 1/10W R547 R548 R549 R550 R551 1-216-073-00 1-216-049-91 1-216-065-91 1-216-025-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1K 4.7K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R619 R620 R621 R622 R623 1-216-657-11 1-216-675-91 1-216-363-00 1-216-363-00 1-260-135-11 METAL CHIP METAL CHIP METAL OXIDE METAL OXIDE CARBON 1.8K 10K 0.33 0.33 1M 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 2W F 2W F 1/2W R552 R553 R554 R555 R556 1-216-089-91 1-216-643-11 1-216-009-91 1-216-025-91 1-216-001-00 RES,CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 47K 470 22 100 10 5% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R624 R626 R627 R628 R631 1-249-401-11 1-260-135-11 1-202-933-61 1-249-401-11 1-216-651-11 CARBON CARBON FUSIBLE CARBON METAL CHIP 47 1M 0.1 47 1K 5% 5% 10% 5% 0.50% 1/4W F 1/2W 1/2W F 1/4W F 1/10W R559 R560 R561 R562 R564 1-216-073-00 1-216-675-91 1-216-675-91 1-216-643-11 1-216-049-91 RES,CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 10K 10K 10K 470 1K 5% 0.50% 0.50% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R635 R636 R638 R641 R642 1-260-135-11 1-260-135-11 1-216-081-00 1-216-041-00 1-202-933-61 CARBON CARBON RES,CHIP RES,CHIP FUSIBLE 1M 1M 22K 470 0.1 5% 5% 5% 5% 10% 1/2W 1/2W 1/10W 1/10W 1/2W F R565 R566 R567 R569 R570 1-216-009-91 1-216-049-91 1-216-083-00 1-216-683-11 1-216-051-00 RES,CHIP RES,CHIP RES,CHIP METAL CHIP RES,CHIP 22 1K 27K 22K 1.2K 5% 5% 5% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R643 R644 R645 R651 R652 1-202-933-61 1-202-933-61 1-202-933-61 1-216-097-91 1-215-481-00 FUSIBLE FUSIBLE FUSIBLE RES,CHIP METAL 0.1 0.1 0.1 100K 330K 10% 10% 10% 5% 1% 1/2W F 1/2W F 1/2W F 1/10W 1/4W R571 R572 R573 R574 R575 1-216-073-00 1-216-057-00 1-216-105-91 1-216-069-00 1-216-698-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 10K 2.2K 220K 6.8K 91K 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R653 R654 R657 R658 R659 1-216-691-11 1-216-049-91 1-216-041-00 1-216-101-00 1-216-049-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 1K 470 150K 1K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R576 R577 R578 R579 R580 1-216-663-11 1-216-065-91 1-216-675-91 1-216-675-91 1-216-663-11 METAL CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 4.7K 10K 10K 3.3K 0.50% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R661 R662 R664 R665 R666 1-216-653-11 1-215-483-00 1-215-473-00 1-216-675-91 1-216-386-11 METAL CHIP METAL METAL METAL CHIP METAL OXIDE 1.2K 390K 150K 10K 0.56 0.50% 1% 1% 0.50% 5% 1/10W 1/4W 1/4W 1/10W 3W F R581 R582 R583 R584 R585 1-216-685-11 1-216-683-11 1-216-063-91 1-216-053-00 1-216-097-91 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 27K 22K 3.9K 1.5K 100K 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R667 R668 R669 R672 R677 1-216-073-00 1-247-895-91 1-216-049-91 1-202-933-61 1-216-089-91 RES,CHIP CARBON RES,CHIP FUSIBLE RES,CHIP 10K 470K 1K 0.1 47K 5% 5% 5% 10% 5% 1/10W 1/4W 1/10W 1/2W F 1/10W R586 R588 R589 R590 R591 1-249-429-11 1-249-405-11 1-208-610-11 1-216-035-00 1-216-073-00 CARBON CARBON METAL OXIDE RES,CHIP RES,CHIP 10K 100 2M 270 10K 5% 5% 5% 5% 5% 1/4W 1/4W F 1W 1/10W 1/10W R678 R679 R680 R682 R683 1-216-073-00 ! 1-202-727-00 ! 1-202-727-00 1-202-933-61 1-202-933-61 RES,CHIP SOLID SOLID FUSIBLE FUSIBLE 10K 4.7M 4.7M 0.1 0.1 5% 20% 20% 10% 10% 1/10W 1/2W 1/2W 1/2W F 1/2W F 9-16 Remark Remark BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G Ref.No. Part No. Description R684 R685 R686 R1502 R1505 RES,CHIP RES,CHIP RES,CHIP METAL OXIDE CARBON 22K 22K 4.7K 100 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 3W F 1/4W F R1506 1-249-417-11 R1507 1-249-401-11 R1508 1-249-397-11 R1509 ! 1-216-675-91 R1512 1-216-081-00 CARBON CARBON CARBON METAL CHIP RES,CHIP 1K 47 22 10K 22K 5% 5% 5% 0.50% 5% 1/4W 1/4W F 1/4W F 1/10W 1/10W R1514 R1515 R1516 R1517 R1518 1-216-073-00 1-216-093-91 1-216-667-11 1-216-667-11 1-216-673-11 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 10K 68K 4.7K 4.7K 8.2K 5% 5% 0.50% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1519 R1520 R1521 R1522 R1523 1-208-610-11 1-208-612-11 1-216-667-11 1-216-667-11 1-216-669-11 METAL OXIDE METAL OXIDE METAL CHIP METAL CHIP METAL CHIP 2M 10M 4.7K 4.7K 5.6K 5% 5% 0.5% 0.5% 0.5% 1W 1W 1/10W 1/10W 1/10W R1524 R1525 R1526 R1532 R1533 1-202-830-00 1-216-073-00 1-216-073-00 1-216-679-11 1-216-673-11 SOLID RES,CHIP RES,CHIP METAL CHIP METAL CHIP 10K 10K 10K 15K 8.2K 20% 5% 5% 0.50% 0.50% 1/2W 1/10W 1/10W 1/10W 1/10W R1534 R1535 R1541 R1544 R1545 1-216-693-11 1-218-754-11 1-216-073-00 1-216-073-00 1-216-113-00 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 56K 120K 10K 10K 470K 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1546 R1547 R1548 R1549 R1550 1-249-443-11 1-216-667-11 1-216-049-91 1-216-687-11 1-216-687-11 CARBON RES,CHIP RES,CHIP METAL CHIP METAL CHIP 0.47 4.7K 1K 33K 33K 5% 0.5% 5% 0.50% 0.50% 1/4W F 1/10W 1/10W 1/10W 1/10W R1551 R1552 R1553 R1554 R1555 1-216-049-91 1-216-089-91 1-216-065-91 1-216-049-91 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 47K 4.7K 1K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1556 R1557 R1558 R1559 R1560 1-216-675-91 1-216-699-91 1-218-776-11 1-216-049-91 1-216-693-11 METAL CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 10K 100K 1M 1K 56K 0.50% 0.50% 0.50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1561 R1562 R1563 R1566 R1567 1-216-695-11 1-216-049-91 1-216-089-91 1-216-081-00 1-216-097-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 68K 1K 47K 22K 100K 0.50% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1568 R1569 R1570 R1571 R1572 1-216-089-91 1-216-669-11 1-216-085-00 1-216-097-91 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 5.6K 33K 100K 10K 5% 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1573 1-216-121-91 R1574 1-216-073-00 R1575 1-216-067-00 R1576 1-216-627-11 R1577 ! 1-216-668-11 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 1M 10K 5.6K 100 5.1K 5% 5% 5% 0.50% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1578 R1579 R1580 R1581 R1582 1-216-093-91 1-216-693-11 1-216-685-11 1-216-061-00 1-216-073-00 RES,CHIP METAL CHIP METAL CHIP RES,CHIP RES,CHIP 68K 56K 27K 3.3K 10K 5% 0.50% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1583 1-216-097-91 RES,CHIP 100K 5% 1/10W 1-216-081-00 1-216-081-00 1-216-065-91 1-215-911-11 1-249-397-11 Remark BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Ref.No. Part No. Description Remark R1584 R1585 R1586 R1587 1-216-679-11 1-216-693-11 1-216-675-91 1-216-687-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 56K 10K 33K 0.50% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W R1588 R1589 R1590 R2501 R2502 1-216-691-11 1-216-699-11 1-216-699-11 1-216-037-00 1-249-449-11 METAL CHIP METAL CHIP METAL CHIP RES,CHIP CARBON 47K 100K 100K 330 1.5 0.5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W F R2503 R2504 R2505 R2506 R2509 1-216-675-91 1-249-449-11 1-249-443-11 1-260-308-11 1-216-073-00 METAL CHIP CARBON CARBON CARBON RES,CHIP 10K 1.5 0.47 22 10K 0.50% 5% 5% 5% 5% 1/10W 1/4W F 1/4W F 1/2W 1/10W R2510 R2512 R2513 R2514 R2517 1-216-059-00 1-216-073-00 1-216-069-00 1-216-065-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 2.7K 10K 6.8K 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2518 R2519 R2520 R2521 R2522 1-249-383-11 1-216-073-00 1-216-453-00 1-216-373-11 1-216-065-91 CARBON RES,CHIP METAL OXIDE METAL OXIDE RES,CHIP 1.5 10K 270 2.2 4.7K 5% 5% 5% 5% 5% 1/4W 1/10W 2W F 2W F 1/10W R2523 R2524 R2525 R2526 R2527 1-216-373-11 1-216-073-00 1-216-017-91 1-216-057-00 1-260-288-11 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP CARBON 2.2 10K 47 2.2K 0.47 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/2W F R2528 R2529 R2530 R2531 R2538 1-260-288-11 1-216-448-11 1-249-476-11 1-216-081-00 1-215-907-11 CARBON METAL OXIDE CARBON RES,CHIP METAL OXIDE 0.47 39 1.5 22K 22 5% 5% 5% 5% 5% 1/2W F 2W F 1/2W F 1/10W 3W F R2539 R2540 R2545 R2546 R2547 1-215-907-11 1-215-907-11 1-216-073-00 1-216-073-00 1-216-448-11 METAL OXIDE METAL OXIDE RES,CHIP RES,CHIP METAL OXIDE 22 22 10K 10K 39 5% 5% 5% 5% 5% 3W F 3W F 1/10W 1/10W 2W F R2548 R2549 R2550 R2551 R2552 1-216-073-00 1-216-073-00 1-216-097-91 1-215-862-11 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP METAL OXIDE RES,CHIP 10K 10K 100K 68 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1W F 1/10W R2554 R2556 R2557 R2558 R2559 1-215-886-11 1-216-073-00 1-215-912-11 1-216-097-91 1-216-065-91 METAL OXIDE RES,CHIP METAL OXIDE RES,CHIP RES,CHIP 100 10K 150 100K 4.7K 5% 5% 5% 5% 5% 2W F 1/10W 3W F 1/10W 1/10W R2560 R2561 R2562 R2563 R2564 1-249-393-11 1-216-053-00 1-216-081-00 1-216-057-00 1-216-369-00 CARBON RES,CHIP RES,CHIP RES,CHIP METAL OXIDE 10 1.5K 22K 2.2K 1 5% 5% 5% 5% 5% 1/4W F 1/10W 1/10W 1/10W 2W F R2565 R2570 R2571 R2572 R2574 1-216-025-91 1-216-077-91 1-216-065-91 1-215-905-11 1-215-908-00 RES,CHIP RES,CHIP RES,CHIP METAL OXIDE METAL OXIDE 100 15K 4.7K 10 33 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 3W F 3W F R2575 1-216-452-11 METAL OXIDE 180 5% 2W F RY601 ! 1-515-738-11 RELAY RY602 1-755-018-11 RELAY RY2501 1-755-167-11 RELAY, AC POWER 9-17 G G1 HA Ref.No. Part No. Description Remark Ref.No. Part No. T503 T602 T603 T605 T2501 T2502 T2503 1-424-555-11 TRANSFORMER, FERRITE (DFT) ! X-4560-177-1 TRANSFORMER ASSY, FLYBACK NX-4141/J1A4 1-423-855-11 TRANSFORMER, FERRITE (HRT) ! 1-423-333-11 TRANSFORMER, LINE FILTER (LFT) 1-416-913-11 INDUCTOR 0µH 1-435-285-11 1-437-207-11 1-423-853-11 1-431-443-11 Remark < IC > T501 T502 Description IC1601 IC1602 < COIL > L1601 L1602 CONVERTER TRANSFORMER, FERRITE (HOT) TRANSFORMER, FERRITE (HDT) TRANSFORMER, FERRITE (HST) 8-759-490-02 IC TOP224Y-BB 8-759-140-85 IC µPC1093J 1-411-799-11 COMMON MODE CHOKE 7µH 1-406-975-21 CHOKE 47µH PH601 PH602 TH501 1-807-973-11 THERMISTOR THP601! 1-808-059-31 THERMISTOR, POSITIVE 8-749-010-64 PHOTO COUPLER PC123F2 8-749-010-64 PHOTO COUPLER PC123F2 Q1601 Q1602 Q1603 8-729-033-26 TRANSISTOR DTA114GKAT146 8-729-033-25 TRANSISTOR DTC114GKA 8-729-033-25 TRANSISTOR DTC114GKA VDR601!1-810-622-11 VARISTOR VDR602!1-801-073-31 VARISTOR TNR14V471K660 **************************************************************** * A-1316-504-A G1 COMPL *********** C1601 C1602 C1603 C1604 C1605 1-104-665-11 1-164-004-11 1-107-906-11 1-107-911-11 1-107-888-11 ELECT CERAMIC CHIP ELECT ELECT ELECT 100µF 0.1µF 10µF 220µF 47µF 20% 10% 20% 20% 20% 10V 25V 50V 50V 25V C1606 C1607 C1608 C1609 C1610 1-163-021-91 1-107-880-11 1-107-880-11 1-164-004-11 1-107-906-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT 0.01µF 4700µF 4700µF 0.1µF 10µF 10% 20% 20% 10% 20% 50V 10V 10V 25V 50V C1611 1-128-339-11 ELECT 2200µF 20% 10V R1601 R1602 R1603 R1604 R1605 1-216-017-91 1-249-387-11 1-216-073-00 1-216-009-91 1-216-057-00 RES,CHIP CARBON RES,CHIP RES,CHIP RES,CHIP 47 3.3 10K 22 2.2K 5% 5% 5% 5% 5% 1/10W 1/4W F 1/10W 1/10W 1/10W R1606 R1607 R1608 R1609 R1610 1-216-049-91 1-216-035-00 1-216-667-11 1-216-667-11 1-216-049-91 RES,CHIP RES,CHIP METAL CHIP METAL CHIP RES,CHIP 1K 270 4.7K 4.7K 1K 5% 5% 0.50% 0.50% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1611 R1612 R1613 1-216-001-00 RES,CHIP 1-216-675-91 METAL CHIP 1-216-659-11 METAL CHIP 10 10K 2.2K 5% 1/10W 0.50% 1/10W 0.50% 1/10W T1601 **************************************************************** * A-1372-664-A HA MOUNT (D14H5) ******************** CN1601 * 1-691-292-11 CONNECTOR 3P CN1602 * 1-779-370-11 CONNECTOR 3P D1601 D1602 D1603 D1604 D1605 8-719-033-53 8-719-033-53 8-719-989-21 8-719-066-51 8-719-063-73 D1606 D1607 8-719-510-41 DIODE D10SC9M 8-719-109-86 DIODE RD5.1ESB3 DIODE RD6.8SB2-T1 DIODE RD6.8SB2-T1 DIODE SC311-6-TE12RA DIODE P6KE170AG23 DIODE D1NL20U-TR < FUSE > F1603 ! 1-533-987-11 FUSE (5A/125V) < FERRITE BEAD > FB1601 9-18 1-435-184-11 TRANSFORMER, CONVERTER 1-410-397-21 FERRITE C201 C202 C203 C204 C205 1-126-206-11 1-126-206-11 1-126-206-11 1-126-206-11 1-126-206-11 ELECT CHIP ELECT CHIP ELECT CHIP ELECT CHIP ELECT CHIP 100µF 100µF 100µF 100µF 100µF 20% 20% 20% 20% 20% 6.3V 6.3V 6.3V 6.3V 6.3V C206 C207 C211 C212 C213 1-126-206-11 1-126-206-11 1-163-031-11 1-163-031-11 1-163-031-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100µF 100µF 0.01µF 0.01µF 0.01µF 20% 20% 6.3V 6.3V 50V 50V 50V C214 C215 C216 C217 C301 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C302 C303 C304 1-163-031-11 CERAMIC CHIP 0.01µF 1-163-031-11 CERAMIC CHIP 0.01µF 1-163-031-11 CERAMIC CHIP 0.01µF 50V 50V 50V 1.1µH BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A HA HB Ref.No. Part No. Description Remark C305 C306 1-163-031-11 CERAMIC CHIP 0.01µF 1-163-031-11 CERAMIC CHIP 0.01µF 50V 50V C307 C308 1-163-031-11 CERAMIC CHIP 0.01µF 1-163-031-11 CERAMIC CHIP 0.01µF 50V 50V CN201 * 1-564-005-11 PIN, CONNECTOR 6P CN202 * 1-564-009-11 PIN, CONNECTOR 10P Ref.No. Part No. Description Remark R211 R212 R213 R214 R215 1-216-085-00 1-216-095-00 1-216-085-00 1-216-095-00 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33K 82K 33K 82K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R216 R217 R301 R302 R303 1-216-089-91 1-216-089-91 1-216-065-91 1-216-065-91 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 47K 4.7K 4.7K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R304 R305 R306 R307 R308 1-216-065-91 1-216-065-91 1-216-065-91 1-216-065-91 1-216-065-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 4.7K 4.7K 4.7K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W D201 D202 D203 D204 D205 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D206 D207 D208 D209 D210 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 S201 S202 S203 S204 S205 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 SWITCH, KEY BOARD (POWER) SWITCH, KEY BOARD (DEGAUSS) SWITCH, KEY BOARD (NUM-1) SWITCH, KEY BOARD (NUM-2) SWITCH, KEY BOARD (NUM-3) D211 D212 D213 D214 D215 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 S206 S207 S208 S209 S210 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 SWITCH, KEY BOARD (NUM-0) SWITCH, KEY BOARD (NUM-4) SWITCH, KEY BOARD (NUM-5) SWITCH, KEY BOARD (NUM-6) SWITCH, KEY BOARD (NUM-CLEAR) D216 D217 D218 D219 D220 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 S211 S212 S213 S214 S215 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 SWITCH, KEY BOARD (NUM-7) SWITCH, KEY BOARD (NUM-8) SWITCH, KEY BOARD (NUM-9) SWITCH, KEY BOARD (NUM-ENTER) SWITCH, KEY BOARD (ENCODER 0) D221 D222 D223 D224 D225 8-719-073-01 8-719-073-01 8-719-987-45 8-719-987-45 8-719-987-45 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD S216 S217 S218 S219 S220 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 SWITCH, KEY BOARD (ENCODER 1) SWITCH, KEY BOARD (ENCODER 2) SWITCH, KEY BOARD (ENCODER 3) SWITCH, KEY BOARD (MENU) SWITCH, KEY BOARD (ENTER) D226 D231 8-719-987-45 DIODE CL-155Y/PG-CD 8-719-158-19 DIODE RD6.2SB S221 S222 S231 S232 S233 1-692-037-31 1-692-037-31 1-473-469-11 1-473-469-11 1-473-469-11 SWITCH, KEY BOARD (UP) SWITCH, KEY BOARD (DOWN) ENCODER, ROTARY (CONTRAST) ENCODER, ROTARY (BRIGHT) ENCODER, ROTARY (CHROMA) S234 1-473-469-11 ENCODER, ROTARY (PHASE) IC201 IC202 8-759-342-19 IC NJU3716M-T2 8-759-342-19 IC NJU3716M-T2 Q201 Q202 Q203 **************************************************************** * A-1372-665-A HB MOUNT (D14H5) ******************* 1-801-806-11 TRANSISTOR DTC144EKA-T146 8-729-921-12 TRANSISTOR 2SD1834 8-729-921-12 TRANSISTOR 2SD1834 R201 R202 R203 R204 R205 1-216-043-91 1-216-043-91 1-216-043-91 1-216-043-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 560 560 560 560 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R206 R207 R208 R209 R210 1-216-049-91 1-216-049-91 1-216-065-91 1-216-049-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 4.7K 1K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A C101 C102 C111 C112 C113 1-126-391-11 1-126-391-11 1-163-031-11 1-163-031-11 1-163-031-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47µF 47µF 0.01µF 0.01µF 0.01µF 20% 20% 6.3V 6.3V 50V 50V 50V CN101 1-506-471-11 PIN, CONNECTOR 6P 9-19 HB HC Ref.No. Part No. Description Remark D101 D102 D103 D104 D105 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D106 D107 D108 D109 D110 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 D111 D121 D122 D123 D124 8-719-158-19 8-719-987-45 8-719-987-45 8-719-987-45 8-719-987-45 DIODE RD6.2SB DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD D125 D126 D127 D128 D129 8-719-987-45 8-719-987-45 8-719-987-45 8-719-987-45 8-719-987-45 DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD DIODE CL-155Y/PG-CD D130 8-719-987-45 DIODE CL-155Y/PG-CD Ref.No. Part No. Description Remark S103 S104 S105 1-692-037-31 SWITCH, KEY BOARD (/SYNC) 1-692-037-31 SWITCH, KEY BOARD (BLUE ONLY) 1-692-037-31 SWITCH, KEY BOARD (MON/R) S106 S107 S108 S109 S110 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 1-692-037-31 SWITCH, KEY BOARD (APT/G) SWITCH, KEY BOARD (COMB/B) SWITCH, KEY BOARD (F1/F3) SWITCH, KEY BOARD (F2/F4) SWITCH, KEY BOARD (ADDRESS/MAKER) **************************************************************** * A-1375-185-A HC COMPL (D14H5) ******************* 1-540-044-11 SOCKET, IC IC101 IC102 8-759-342-19 IC NJU3716M-T2 8-759-342-19 IC NJU3716M-T2 Q101 Q102 Q103 8-729-921-12 TRANSISTOR 2SD1834 8-729-921-12 TRANSISTOR 2SD1834 1-801-806-11 TRANSISTOR DTC144EKA-T146 R101 R102 R103 R104 R105 1-216-043-91 1-216-043-91 1-216-043-91 1-216-043-91 1-216-043-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 560 560 560 560 560 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 R109 R110 1-216-043-91 1-216-043-91 1-216-043-91 1-216-043-91 1-216-043-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 560 560 560 560 560 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R112 R113 R114 R115 R116 1-216-097-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 1K 1K 1K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R117 R121 R122 R123 R124 1-216-065-91 1-216-085-00 1-216-095-00 1-216-085-00 1-216-095-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 33K 82K 33K 82K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R125 R126 R127 1-216-089-91 RES,CHIP 1-216-089-91 RES,CHIP 1-216-089-91 RES,CHIP 47K 47K 47K 5% 5% 5% 1/10W 1/10W 1/10W C1 C2 C4 C50 C52 1-163-227-11 1-163-227-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10PF 10PF 0.01µF 0.01µF 0.01µF 0.5PF 50V 0.5PF 50V 50V 50V 50V C53 C54 C55 C56 C57 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C58 C59 C60 C61 C62 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C63 C64 C65 C67 C68 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C81 C82 C83 C84 C85 1-126-206-11 1-124-635-00 1-126-206-11 1-126-206-11 1-126-206-11 ELECT CHIP ELECT ELECT CHIP ELECT CHIP ELECT CHIP 100µF 220µF 100µF 100µF 100µF 20% 20% 20% 20% 20% 6.3V 6.3V 6.3V 6.3V 6.3V C86 C87 C89 1-126-206-11 ELECT CHIP 1-126-206-11 ELECT CHIP 1-126-206-11 ELECT CHIP 100µF 100µF 100µF 20% 20% 20% 6.3V 6.3V 6.3V CN2 CN3 CN4 CN5 1-506-474-11 * 1-564-009-11 * 1-564-005-11 1-506-471-11 PIN, CONNECTOR 9P PIN, CONNECTOR 10P PIN, CONNECTOR 6P PIN, CONNECTOR 6P D1 D2 D3 D4 D5 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB D6 D7 D8 8-719-158-19 DIODE RD6.2SB 8-719-158-19 DIODE RD6.2SB 8-719-158-19 DIODE RD6.2SB S101 S102 9-20 1-692-037-31 SWITCH, KEY BOARD (SHIFT) 1-692-037-31 SWITCH, KEY BOARD (/16.9) BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A HC HD Ref.No. Part No. Description Remark FL1 FL2 FL3 FL4 FL5 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-236-071-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI ENCAPSULATED COMPONENT FL6 FL7 FL8 FL9 FL10 1-236-071-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 ENCAPSULATED COMPONENT FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FL11 FL12 FL13 FL14 FL15 1-236-071-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 ENCAPSULATED COMPONENT FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FL16 1-236-071-11 ENCAPSULATED COMPONENT IC2 IC3 IC9 IC10 IC11 8-759-991-19 8-759-186-47 8-759-186-30 8-759-186-30 8-759-175-27 IC PST529CMT IC TC74VHC138F IC TC74VHC14F IC TC74VHC14F IC TC74VHC574F IC12 IC13 8-759-174-16 IC TC74VHC244F 8-759-289-43 IC LTC490CS8 JR2 1-216-296-91 SHORT 0 L2 1-412-537-31 INDUCTOR Ref.No. Part No. Description Remark R60 R61 R62 1-216-089-91 RES,CHIP 1-216-089-91 RES,CHIP 1-216-089-91 RES,CHIP 47K 47K 47K 5% 5% 5% 1/10W 1/10W 1/10W R63 R64 R65 R66 R67 1-216-089-91 1-216-089-91 1-216-089-91 1-216-089-91 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47K 47K 47K 47K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R68 R70 R71 R72 R73 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R74 R75 R76 R77 R78 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R79 R80 R81 R82 R83 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R84 R85 R86 R87 R88 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R89 R90 R91 R92 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R93 R94 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 100K 100K 5% 5% 1/10W 1/10W 100µH X1 R1 R2 R3 R4 R5 1-216-073-00 1-216-295-91 1-216-073-00 1-216-073-00 1-216-073-00 RES,CHIP SHORT RES,CHIP RES,CHIP RES,CHIP 10K 0 10K 10K 10K 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R6 R7 R12 R13 R14 1-216-073-00 1-216-097-91 1-216-073-00 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 100K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R15 R16 R19 R20 R21 1-216-049-91 1-216-073-00 1-216-073-00 1-216-073-00 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 10K 10K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R22 R23 R24 R25 R26 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R27 R28 R41 R42 R43 1-216-049-91 1-216-049-91 1-216-073-00 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R44 R50 1-216-073-00 RES,CHIP 1-216-097-91 RES,CHIP 10K 100K 5% 5% 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1-767-892-21 VIBRATOR, CRYSTAL (20 MHz) **************************************************************** * A-1372-136-A HD MOUNT (D14H1) ******************* CN101 CN102 1-565-269-11 SOCKET, CONNECTOR (D-DUB,L) 9P 1-506-474-11 PIN, CONNECTOR 9P D101 D102 D103 D104 D105 8-719-037-00 8-719-037-00 8-719-037-00 8-719-037-00 8-719-037-00 DIODE RD6.2SB2-T1 DIODE RD6.2SB2-T1 DIODE RD6.2SB2-T1 DIODE RD6.2SB2-T1 DIODE RD6.2SB2-T1 **************************************************************** 9-21 MA Ref.No. Part No. Description Remark * A-1306-572-A MA COMPL ************ 1-540-222-11 SOCKET, IC (PCC PACKAGE) 84P 1-550-104-11 HOLDER, BATTERY BATTERY, LITHIUM CR2025 Ref.No. Part No. Description C165 C166 C168 C169 C171 1-126-400-11 1-126-392-11 1-126-392-11 1-163-031-11 1-163-031-11 ELECT CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP C172 1-126-392-11 ELECT CHIP Remark 22µF 100µF 100µF 0.01µF 0.01µF 20% 20% 20% 35V 6.3V 6.3V 50V 50V 100µF 20% 6.3V C101 C102 C103 C104 C105 1-163-031-11 1-126-392-11 1-126-392-11 1-163-031-11 1-163-235-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 100µF 100µF 0.01µF 22PF 5% C106 C108 C109 C110 C111 1-163-227-11 1-126-392-11 1-126-392-11 1-163-031-11 1-126-392-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP 10PF 100µF 100µF 0.01µF 100µF 0.5PF 50V 20% 6.3V 20% 6.3V 50V 20% 6.3V C112 C113 C114 C115 C116 1-126-392-11 1-163-031-11 1-163-031-11 1-163-031-11 1-126-392-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 100µF 0.01µF 0.01µF 0.01µF 100µF 20% C117 C118 C119 C120 C121 1-163-031-11 1-126-392-11 1-163-031-11 1-163-031-11 1-126-392-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.01µF 100µF 0.01µF 0.01µF 100µF C122 C123 C124 C125 C126 1-126-392-11 1-163-031-11 1-163-031-11 1-126-392-11 1-163-031-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 100µF 0.01µF 0.01µF 100µF 0.01µF C127 C128 C129 C130 C131 1-163-031-11 1-126-392-11 1-126-392-11 1-163-031-11 1-163-031-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 100µF 100µF 0.01µF 0.01µF C132 C133 C134 C135 C136 1-126-392-11 1-126-392-11 1-163-031-11 1-163-031-11 1-126-392-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 100µF 100µF 0.01µF 0.01µF 100µF C137 C139 C140 C141 C142 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF 50V 50V 50V 50V 50V C144 C145 C147 C148 C149 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-126-392-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.01µF 0.01µF 0.01µF 0.01µF 100µF 20% 50V 50V 50V 50V 6.3V C150 C151 C153 C154 C159 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-126-392-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.01µF 0.01µF 0.01µF 0.01µF 100µF 20% 50V 50V 50V 50V 6.3V C160 C161 C162 C163 C164 1-163-031-11 1-163-031-11 1-163-031-11 1-126-392-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 100µF 0.01µF 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 50V 6.3V 6.3V 50V 50V 6.3V 50V 50V 50V 6.3V CN101 CN102 CN103 CN105 PLUG, CONNECTOR 10P PIN, CONNECTOR (PC BOARD) 50P PLUG, CONNECTOR 7P PLUG, CONNECTOR 9P D101 D102 D103 D104 D109 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB 50V 6.3V 50V 50V 6.3V FL103 FL104 FL105 FL107 FL108 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI 6.3V 50V 50V 6.3V 50V FL109 FL110 FL111 FL112 FL113 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI 50V 6.3V 6.3V 50V 50V FL114 FL115 FL117 FL120 FL123 1-236-071-11 1-236-071-11 1-236-071-11 1-239-183-11 1-239-183-11 ENCAPSULATED COMPONENT ENCAPSULATED COMPONENT ENCAPSULATED COMPONENT FILTER, EMI FILTER, EMI 6.3V 6.3V 50V 50V 6.3V FL124 1-239-183-11 FILTER, EMI 50V 50V 50V 6.3V 50V IC101 IC102 IC103 IC104 IC106 8-759-186-44 8-759-082-59 8-759-925-75 8-759-239-98 8-759-644-13 IC TC74VHC125F IC TC7W32FU IC SN74HC05ANS IC TC74HC30AF IC HD6435368AX06M IC107 IC108 IC109 IC110 IC111 8-759-081-44 8-759-553-93 8-759-186-47 8-759-346-07 8-759-497-29 IC TC74VHC04F IC MBM29F400BC-90PF IC TC74VHC138F IC MM1026BFB IC LC35256DM-70-TLM IC112 IC113 8-752-381-84 IC CXD1095BQ 8-759-575-91 IC MAX490ECSA JR101 JR102 JR103 1-216-295-91 SHORT 0 1-216-295-91 CONDUCTOR,CHIP 1-216-097-91 RES,CHIP 100K 0 5% 1/10W L101 9-22 * 1-564-525-11 * 1-793-722-11 * 1-564-522-11 * 1-564-524-11 1-412-537-31 INDUCTOR 100µH BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A MA MB Ref.No. Part No. Description Remark Q102 Q103 Q104 Q105 Q106 8-729-027-38 1-801-806-11 1-801-806-11 8-729-903-46 8-729-903-46 TRANSISTOR DTA144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC144EKA-T146 TRANSISTOR 2SB1132-P TRANSISTOR 2SB1132-P Ref.No. Part No. Description Remark R160 R161 R162 1-216-073-00 RES,CHIP 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 10K 100K 100K 5% 5% 5% 1/10W 1/10W 1/10W R163 R164 R165 R166 R167 1-216-097-91 1-216-097-91 1-216-097-91 1-216-025-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R168 R169 R170 R171 R172 1-216-025-91 1-216-097-91 1-216-025-91 1-216-025-91 1-216-053-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100K 100 100 1.5K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R173 R178 R179 R180 R181 1-216-025-91 1-216-053-00 1-216-047-91 1-216-073-00 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 1.5K 820 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R182 R183 R184 R185 R186 1-216-025-91 1-216-073-00 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 10K 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R187 R188 R189 R190 R191 1-216-025-91 1-216-025-91 1-216-025-91 1-216-033-00 1-216-033-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 220 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R192 R193 R194 R195 R196 1-216-097-91 1-216-033-00 1-216-033-00 1-216-033-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 220 220 220 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R197 R198 1-216-073-00 RES,CHIP 1-216-097-91 RES,CHIP 10K 100K 5% 5% 1/10W 1/10W R101 R102 R103 R104 R105 1-216-097-91 1-216-097-91 1-216-025-91 1-216-025-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 R109 R110 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R111 R112 R113 R115 R116 1-216-097-91 1-216-097-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R117 R118 R119 R120 R121 1-216-025-91 1-216-097-91 1-216-097-91 1-216-025-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100K 100K 100 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R122 R123 R124 R125 R126 1-216-025-91 1-216-121-91 1-216-025-91 1-216-065-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 1M 100 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R127 R128 R129 R130 R131 1-216-065-91 1-216-097-91 1-216-097-91 1-216-049-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 100K 100K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R132 R133 R134 R135 R136 1-216-097-91 1-216-049-91 1-216-049-91 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 1K 1K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R137 R138 R139 R140 R141 1-216-073-00 1-216-097-91 1-216-049-91 1-216-097-91 1-216-049-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 100K 1K 100K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R142 R143 R144 R145 R146 1-216-097-91 1-216-049-91 1-216-097-91 1-216-049-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 1K 100K 1K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R147 R148 R150 R151 R152 1-216-049-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 100K 100K 100K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R153 R154 R155 R156 R157 1-216-073-00 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R158 R159 1-216-073-00 RES,CHIP 1-216-049-91 RES,CHIP 10K 1K 5% 5% 1/10W 1/10W THP101 THP102 1-771-075-21 THERMISTOR, POSITIVE 1-771-075-21 THERMISTOR, POSITIVE TP110 TP111 TP112 TP113 TP114 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 PIN, POST PIN, POST PIN, POST PIN, POST PIN, POST X1011-767-892-21 VIBRATOR, CRYSTAL (20 MHz) **************************************************************** * A-1306-571-A MB COMPL ************ 7-432-114-11 SCREW LOCK BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A C1100 C1101 C1102 1-126-206-11 ELECT CHIP 100µF 1-165-319-11 CERAMIC CHIP 0.1µF 1-126-206-11 ELECT CHIP 100µF 20% 20% 6.3V 50V 6.3V 9-23 MB Ref.No. Part No. Description Remark C1103 C1104 1-165-319-11 CERAMIC CHIP 0.1µF 1-163-031-11 CERAMIC CHIP 0.01µF C1105 C1106 C1107 C1108 C1109 1-163-031-11 1-126-206-11 1-126-206-11 1-163-233-11 1-163-031-11 CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 100µF 100µF 18PF 0.01µF C1110 C1111 C1112 C1114 C1115 1-163-231-11 1-126-206-11 1-163-031-11 1-163-031-11 1-126-206-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 15PF 100µF 0.01µF 0.01µF 100µF C1116 C1117 C1118 C1119 C1120 1-163-031-11 1-126-206-11 1-163-021-91 1-107-682-11 1-163-031-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 100µF 0.01µF 1µF 0.01µF C1121 C1122 C1123 C1124 C1125 1-126-206-11 1-165-319-11 1-163-031-11 1-165-319-11 1-126-206-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 100µF 0.1µF 0.01µF 0.1µF 100µF C1126 C1127 C1128 C1129 C1130 1-165-319-11 1-126-206-11 1-165-319-11 1-126-206-11 1-126-206-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP 0.1µF 100µF 0.1µF 100µF 100µF C1131 C1132 C1133 C1134 C1135 1-163-031-11 1-165-319-11 1-165-319-11 1-165-319-11 1-163-021-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.1µF 0.1µF 0.1µF 0.01µF C1136 C1137 C1138 C1139 C1140 1-107-682-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1µF 0.1µF 0.1µF 0.1µF 0.1µF C1141 C1142 C1143 C1144 C1145 1-163-031-11 1-126-206-11 1-163-031-11 1-163-031-11 1-126-206-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.01µF 100µF 0.01µF 0.01µF 100µF C1146 C1147 C1148 C1149 C1150 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-126-206-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.01µF 0.01µF 0.01µF 0.01µF 100µF C1151 C1152 C1153 C1154 C1156 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 1-163-031-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01µF 0.01µF 0.01µF 0.01µF 0.01µF C1157 C1158 C1159 C1160 C1161 1-126-206-11 1-163-031-11 1-126-206-11 1-163-021-91 1-163-021-91 ELECT CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 100µF 0.01µF 100µF 0.01µF 0.01µF C1162 C1180 1-164-690-91 CERAMIC CHIP 0.0022µF 5% 1-163-243-11 CERAMIC CHIP 47PF 5% 20% 20% 5% 5% 20% 20% 20% 10% 10% 20% 20% CN1103 CN1104 50V 6.3V 6.3V 50V 50V CN1105 * 1-564-524-11 PLUG, CONNECTOR 9P CN1106 * 1-564-522-11 PLUG, CONNECTOR 7P CN1107 1-695-581-21 CONNECTOR, D SUB CN1109 1-793-721-11 JACK, MODULAR 50V 6.3V 50V 50V 6.3V 50V 6.3V 50V 16V 50V 6.3V 50V 50V 50V 6.3V 20% 20% 10% 50V 50V 50V 50V 50V 10% 16V 50V 50V 50V 50V 20% 50V 6.3V 50V 50V 6.3V 20% 50V 50V 50V 50V 6.3V 20% 50V 50V 50V 50V 50V 20% 20% 10% 10% Description 50V 50V 50V 6.3V 50V 6.3V 6.3V 20% Ref.No. Part No. 6.3V 50V 6.3V 50V 50V 50V 50V Remark 1-695-581-21 CONNECTOR, D SUB 1-695-581-21 CONNECTOR, D SUB D1100 D1101 D1102 D1103 D1104 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 8-719-037-22 DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD12SB-T1 D1105 D1106 D1107 D1108 D1109 8-719-037-22 8-719-037-22 8-719-037-22 8-719-037-22 8-719-037-22 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD12SB-T1 D1110 D1111 D1112 D1113 D1114 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB D1115 D1116 D1117 D1118 8-719-158-19 8-719-158-19 8-719-158-19 8-719-158-19 DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB DIODE RD6.2SB FL1100 FL1101 FL1102 FL1103 FL1108 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FL1109 FL1110 FL1111 FL1112 FL1113 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FL1114 FL1115 FL1116 FL1117 FL1118 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 1-239-183-11 FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FILTER, EMI FL1119 FL1120 FL1121 1-239-183-11 FILTER, EMI 1-239-183-11 FILTER, EMI 1-239-183-11 FILTER, EMI IC1100 IC1101 IC1102 IC1103 IC1104 8-759-186-26 8-759-186-44 8-759-081-44 8-759-397-01 8-759-186-30 IC TC74VHC02F IC TC74VHC125F IC TC74VHC04F IC MAX487CSA-TE2 IC TC74VHC14F IC1105 IC1106 IC1107 IC1108 IC1109 8-759-594-45 8-759-397-01 8-759-522-14 8-759-594-45 8-759-252-59 IC MAX3100CEE-TG068 IC MAX487CSA-TE2 IC MB90096PF-G-127-BND-ER IC MAX3100CEE-TG068 IC MAX202CSE IC1110 IC1112 8-759-594-46 IC MB90096PF-178 8-759-454-11 IC MC74HC589AFEL CN1100 * 1-564-524-11 PLUG, CONNECTOR 9P CN1101 * 1-564-527-11 PLUG, CONNECTOR 12P CN1102 * 1-793-722-11 PIN, CONNECTOR (PC BOARD) 50P 9-24 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A MB T Ref.No. Part No. Description Remark L1100 L1101 L1102 1-412-537-31 INDUCTOR 1-412-537-31 INDUCTOR 1-412-537-31 INDUCTOR 100µH 100µH 100µH Ref.No. Part No. Description Remark R1167 R1170 1-216-089-91 RES,CHIP 1-216-065-91 RES,CHIP 47K 4.7K 5% 5% 1/10W 1/10W R1171 R1172 R1173 R1174 R1175 1-216-065-91 1-216-089-91 1-216-089-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 47K 47K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1100 R1101 R1102 R1103 R1104 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1176 R1177 R1180 R1181 R1182 1-216-097-91 1-216-097-91 1-216-065-91 1-216-097-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 4.7K 100K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1106 R1107 R1108 R1109 R1110 1-216-025-91 1-216-025-91 1-216-077-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 15K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1183 R1184 R1185 R1186 R1187 1-216-025-91 1-216-025-91 1-216-025-91 1-216-295-91 1-216-295-91 RES,CHIP RES,CHIP RES,CHIP SHORT SHORT 100 100 100 0 0 5% 5% 5% 1/10W 1/10W 1/10W R1111 R1112 R1113 R1114 R1115 1-216-025-91 1-216-025-91 1-216-097-91 1-216-025-91 1-216-025-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1188 R1189 1-216-295-91 SHORT 1-216-295-91 SHORT R1117 R1118 R1119 R1120 R1121 1-216-121-91 1-216-077-91 1-216-025-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1M 15K 100 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W TH1100 R1122 R1123 R1125 R1126 R1127 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1128 R1130 R1131 R1132 R1133 1-216-097-91 1-216-089-91 1-216-097-91 1-216-097-91 1-216-089-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 47K 100K 100K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1136 R1137 R1138 R1140 R1141 1-216-089-91 1-216-295-91 1-216-625-11 1-216-638-11 1-216-073-00 RES,CHIP SHORT METAL CHIP METAL CHIP RES,CHIP 47K 0 82 300 10K 5% 1/10W R1142 R1143 R1144 R1145 R1147 1-216-073-00 1-216-073-00 1-216-073-00 1-216-089-91 1-216-295-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP SHORT 10K 10K 10K 47K 0 5% 5% 5% 5% R1148 R1149 R1151 R1152 R1153 1-216-625-11 1-216-638-11 1-216-049-91 1-216-049-91 1-216-049-91 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 82 300 1K 1K 1K 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1154 R1155 R1156 R1157 R1158 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W CN801 * 1-564-526-11 PLUG, CONNECTOR 11P CN802 1-774-525-11 SOCKET, CONNECTOR 64P CN803 1-774-525-11 SOCKET, CONNECTOR 64P CN804 1-774-525-11 SOCKET, CONNECTOR 64P CN805 * 1-564-523-11 PLUG, CONNECTOR 8P R1159 R1160 R1161 R1162 R1163 1-216-049-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W CN806 * 1-564-525-11 PLUG, CONNECTOR 10P R1164 R1165 R1166 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 100K 100K 100K 5% 5% 5% 1/10W 1/10W 1/10W BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 1-533-817-21 THERMISTOR TP1100 TP1101 TP1102 TP1103 TP1104 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 PIN, POST PIN, POST PIN, POST PIN, POST PIN, POST TP1106 TP1107 TP1108 TP1109 TP1110 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 * 1-537-864-11 PIN, POST PIN, POST PIN, POST PIN, POST PIN, POST TP1111 * 1-537-864-11 PIN, POST TP1112 * 1-537-864-11 PIN, POST TP1113 * 1-537-864-11 PIN, POST 0.50% 1/10W 0.50% 1/10W 5% 1/10W 1/10W 1/10W 1/10W 1/10W 0 0 X1100 1-767-280-21 VIBRATOR, CRYSTAL (3.6864 MHz) **************************************************************** * A-1390-942-A T MOUNT ********** **************************************************************** 9-25 YA YB YC Ref.No. Part No. Description Remark Ref.No. Part No. * A-1373-716-A YA MOUNT *********** Description Remark * A-1373-718-A YC MOUNT (D14H1) ******************* * A-1373-743-A YC MOUNT (D14H5) ******************* CN901 * 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P CN931 * 1-564-724-11 PIN, CONNECTOR (SMALL TYPE) 8P CN932 1-774-533-11 SOCKET, SMALL TYPE DIN (8P) D901 D902 D903 D904 D905 8-719-064-11 8-719-064-11 8-719-064-11 8-719-064-11 8-719-064-11 DIODE SPR-325MVW DIODE SPR-325MVW DIODE SPR-325MVW DIODE SPR-325MVW DIODE SPR-325MVW R901 R902 R903 R904 R905 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R906 R907 R908 R909 R910 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W D931 D932 D933 D934 D935 8-719-037-22 8-719-037-22 8-719-037-22 8-719-037-22 8-719-158-19 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD12SB-T1 DIODE RD6.2SB D936 D937 8-719-037-22 DIODE RD12SB-T1 8-719-037-22 DIODE RD12SB-T1 JR931 JR932 1-216-295-91 SHORT 1-216-295-91 SHORT 0 0 **************************************************************** **************************************************************** * A-1373-717-A YB MOUNT (D14H1) ******************* * A-1373-742-A YB MOUNT (D14H5) ******************* D921 D922 D923 ACCESSORIES ************** ! 1-534-827-14 CORD, POWER 10A/125V (For US) 3-170-078-01 HOLDER (B), PLUG (POWER CORD) 3-867-938-01 MANUAL, OPERATION (JAPANESE/ENGLISH) 4-051-743-01 PLATE, TALLY X-4037-287-1 MASK (4:3) ASSY 8-719-061-96 DIODE SLR-325DCT31 8-719-053-43 DIODE SLR-325VCT31 8-719-060-27 DIODE SLR-325MCT31 **************************************************************** 9-26 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Overall (1/2) Overall (1/2) Section 10 Block Diagrams B1 Y/G BUFF Y/G CLAMP PULSE INSERT Q303 IC306 Q404,405,411,412 DL404,405 IC410 Q406-409 IC1300,1305 Q1300-1302 BUFF Y AMP DELAY SELECT Y BUFF/AMP R CLAMP G Y LEVEL Q400-403,413,414 DL400-403 PB/B IC301,304 Q330-332 PB/B BUFF PB/B CLAMP PULSE INSERT Q333 IC307 BUFF PB AMP B Q501,503,515,516 DL501,502 DELAY PR AMP IC501 Q502,517,518 SELECT PB BUFF/AMP IC1304 IC401 Q1431-1434 Q730-734 CUT OFF SWITCH RGB MATRIX R CLAMP R OUT C Q735 OSD R IC400 DELAY Q201,203 R IK BUFF CUT OFF R IC1302,1306 Q1320-1322 PR LEVEL G CLAMP G-Y/R G IC1308 Q1421-1424 Q750-754 CUT OFF SWITCH G CLAMP G OUT R G Q755 OSD G V901 PICTURE TUBE B IK BUFF CUT OFF G ANALOG I/O PR/R Q301,303 IC302,305 Q365-367 PR/R BUFF PR/R CLAMP PULSE INSERT Q368 BUFF R IC308 Q504,506,511,512 DL503,504 IC501 Q505,513,514 IC401 PR AMP DELAY SELECT PR BUFF/AMP PB AMP IC1303,1307 Q1340-1342 B CLAMP R PB LEVEL CHROMA PB Q1411-1414 Q770-774 B CLAMP B OUT IC502 IC501 BUFF SUB CPU SCLK PIC ABL IC3301 Q3301-3303 Q3304-3319 SYNC SEP SYNC AGC Q1460 BRT ABL IC503 RESET H SYNC SDA V SYNC SCL D/A CONV H SYNC SEP 1 V BLK IC3901 COMP SYNC SEP OPTION ABL H BLK B2 IC4300-4302 IC4350-4352 EEPROM 2 G BOARD Q1460 C CLP P H BLK MISO MOSI G1 IK BUFF Y CLP P SYNC BUFF SYNC CUT OFF B H1,2 IK BUFF Q1402 CHROMA Q401,403 (FBT) Q775 OSD B G-Y/B CHROMA PR IC1309 CUT OFF SWITCH FV1,2 IC300,303 Q300-302 HV Y/G Q101,102 G1 B BX (BKM-129X) H1,2 Overall (1/2) IC3902 SW CONTROL SIGNAL G BOARD IC3904 CLAMP PULSE GEN H BLK IC3902 COMP SYNC SEP SW H SYNC IC3404 EEPROM IC3406 Q3905,3907 IC3902 V SYNC SEP SW H SYNC SEP V SYNC SEP V SYNC IC3908 COMP SYNC SW IC3403 VIDEO CAPTION DECODER IC3400,3401 IC3407 BLK P BUFFER OSD R/G/B OSD R/G/B OSD BLK MB IC112 RESET IC101 MISO MOSI PARALLEL I/O IC106 TALLY(G) D901-905 YA TALLY(R) BUFF SCLK MAIN CPU D0-7 MOSI A0-19 A0-2 IC108 PROGRAM D0-7 ROM A0-17 RESET IC1103,1106 RS485 CONTROL RS485 REM1 CN1103 IN RXD/RXD SCLK IC111 A0-14 SRAM REMOTE1 PROT/ STANDBY/ POWER D0-7 IC1 IC12 MAIN CPU BUS SHIFT MISO MOSI IC201,202 S/P CONV SCLK SCLK CN1107 REMOTE2 IC11 IC9,10 S231-234 BUFF INV ENCODER IC109 IC103 IC1108 IC1109 RS232C CONTROL RS232C I/F OPTION IC1107,1110 OSD RXD/RXD CN101 TXD/TXD CONTORL UNIT HD S/P CONV S101-110 MATRIX SW YC V SYNC D14H1 MODEL IC101,102 D121-130 COMP SYNC RS422 DRIVER ADDRESS DECODER HC SCL IC113 HA IC3 CN1109 MODULAR SDA IC103 MATRIX SW D223-226 IC1112 ADDRESS SELECTOR A15-18 S201-222 MOSI YB RD/WR MA IC13 RS422 DRIVER MISO D921-923 REM2 DRIVER RESET TXD/TXD CN1104 OUT IC110 BAT1 LITHUM BATTERY IC1105 D0-7 MISO MOSI SCLK D14H5 MODEL MISO IC1100 OSD DRIVER HB OSD R/G/B OSD BLK AFC SDA SDA SCL SCL COMP SYNC H SYNC H SYNC V SYNC V SYNC 3 G BOARD BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A 10-1 10-1 Overall (1/2) Overall (2/2) Overall (2/2) Overall (2/2) 3 MB BOARD AFC H BLK V BLK H SYNC V SYNC IC2501 IC507 H FOCAP H BLK SYNC IC526 IC506,Q501 H BLK SCL IC503(1/2) Q2505 H SYNC PULSE GEN H DRIVE T2502 HDT AC IN AC 100-240V 50/60Hz +15V IC601 Q605 PFC CONT IC602 MAIN SWITCHING IC607 -12V REG T603 PFCT +5V REG AC RECT S901 -12V -5V REG RY601 Q513 IC529 HV OUT PLL PULSE GEN IC2503 VDC OUT V OUT EW OUT -5V X RAY IC516 Q509-512 SW DF AMP D/A CONV +B T501 DFT T2503 CURRENT IC512 D623 ±B RECT DY T503 HRT +160V Q602 RELAY DRIVE DGC V BLK CONT V DYL2501 HCC IC503(2/2) V OUT D626 RY602 PWM V SYNC IN +5V IC609 POWER Q2503 HV REG IC522 PLL INH IC608 D625 ±6V RECT D602 Q519 V SYNC PULSE GEN IC502 V FOC Q608 IC528 V BLK SYNC -15V +12V V DY+ H CENTER AMP PWM CONT IC510 +12V REG IC2501 T2501 HOT IC515 H FOC D624 ±15V RECT H DYIC2502 H OUT COL H LOCK IC606 H DY+ H OUT HV IN T605 PIT Q2508 DELAY G ABL IC509 IC527 H BLK DEF CONTROL SDA IC501 1 B BOARD L2504 HLC H BLK(F) V BLK(B) L2503 HLC H BLK(R0 Q601,619 4:3/16:9 DEGAUS DRIVE H1 50/60 Q2511 H SIZE RELAY SW Q524,529-531 H2 Q609 PH603 +B FEED BACK ISORATOR PH604 PFC & MAIN ON/OFF ISORATOR IC610 1125/50 +B REG RY2501 SW IC508 D/A CONV Q611-613 Q620-622 Q615 SW DC IN H CENT HV PROT Q2514,2515 Q2518,2519 Q618 POWER ON /OFF +18V H DL V DL POWER 15K S-CAP ON/OFF 33.75K DGC SW +18V IC1601 SW STBY 5V SW IC514,523 HV PROT T502 FBT G1 T1601 SRT DC IN Q1601 Q520 HV PROT HV HV FV1 FV1 FV2 FV2 PICTURE TUBE IC517,523 D1606 IK PROT STBY 5V D1605 Q517,518 G2 AMP G2 2 C BOARD H1 H2 PH601 CTL FEED BACK ISORATOR PH602 OVP FEED BACK ISORATOR IC1602 STBY 5V REG 5V SENSE Q1603 SW Overall (2/2) 10-2 10-2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B (1/2), BX, B1, B2 B (1/2) /BX, B1, B2 B Block (1/2) BX Block B1 Block B2 Block SELECT ) BX ( SIGNAL SUB CPU TB001 TP101 ANALOG I/O Y/G BUFF Q101,103 Y/G B12 CN001(2/2) Y/G OUT T B (1/2) (SIGNAL SELECT) TP300 Y/G Y/G AMP Q300,301 1 Q102 TP201 12 4 CLAMP Q302(1/2) 3 TP301 PB/B BUFF Q201,203 B14 Y LEVEL (2/2) PB/B +5V 3 B16 13 5 4 PR/R OUT CLAMP Q332(1/2) 3 5 CN411(1/2) BUFF Q304 7 SYNC BUFF Q401,403 MISO B27 IC502 2 3 1 MOSI A28 IC502 12 11 13 CN001(1/2) IC501 SUB CPU 1 SO2 2 SI2 PR/R 1 3 Q404 SCLK B28 SLOT1 ID A31 IC502 5 8 10 IC503 EEPROM 6 64 SCLK2 14 INT0 4 SI1 53 2 SO SO1 52 5 SI SCLK1 51 EECS 50 6 SCK 1 CS0 A21 HS OUT B21 VS OUT B20 VS IN A20 HS IN 2 19 RSTX +6V A7 +6V B7 -6V A6 -6V B6 5V REG D/A CONV OPTION 3 SDA 14 4 SCL 15 5 9 X1 23 A29 STBY 5V B29 BUFF Q402 BUFF Q403 BUFF Q414 BUFF Q400 3 X0 22 D/A CONV -5V 14 12 IC450 BUFF Q401 7 14 11 3 6 2 Q410 BUFF Q413 DL401 CLAMP Q367(1/2) 3 3 BUFF Q503 DL502 BUFF Q516 12 13 2 BUFF Q368 15 1 11 IC305 CLAMP 3 1 5 4 PB 1 H SYNC SEP1 10 IC308 1 9 3 PR AMP H SYNC SEP1 1 5 BUFF Q369 1 CN412(1/3) CN402(1/2) PR PR BUFF Q501 DL501 BUFF Q515 PB BUFF/AMP Q502,517,518 4 PB BUFF Q506 DL504 BUFF Q512 4 PR BUFF/AMP Q505,513,514 2 CN402(2/2) PR 5 APER IC501 1 5 3 4 14 11 TP304 9 APER SW CLP P SW BUFF Q504 APER SW H BLK (2/2) Y/G BLACK DL503 BUFF Q511 7 2 9 SCL(2/2) 6 SDA MONO CHROMA/PB SCL IC3404 EEPROM CHROMA/PR APER SW 15 10 3 COMP SYNC H SYNC 9 7 V SYNC 8 CN421 V SYNC 6 H SYNC 2 4 IC3406 SDA 5 CHROMA EXT SYNC SEL IC3301 H SYNC SEP1 H SYNC SEP2 BUFF Q3301 CLP P DLY 12 IC3301 14 13 SDI SEL 11 5 DAC2 (2/2) 4 SUB PIC (2/2) 4 SDA(2/2) PB/B BLACK PR/R BLACK CN308 SDA 5 SCL 1 COMP SYNC SEP 2 H SYNC SEP E 3 V SYNC SEP MB BOARD CN1100 8 CN422(1/2) V SYNC SEP 9 H SYNC SEP 7 H BLK SCL 6 14 5V-2 IC3301 BUFF Q3302 15 2 5 1 3 BUFF Q3303 10 Q3304-3319 4 SYNC AGC 12 COMP SYNC SEP 9 2 H SYNC SEP1 3 H SYNC SEP2 4 CLP P DLY 5 SDI SEL 7 COMP SYNC 5 Y CLP P 10 C CLP P 11 CAPTION Y 8 IC3901 H SYNC SEP Q 6 CN3902 (1/2) 12 CK Q 10 COMP SYNC SEP 12 2 Q 7 CxRx 14 15 1 2 12 CK Q 9 4 CK Q 7 CxRx 10 Q3906 Q3901 IC3904 CLAMP PULSE GEN IC3902 4 CK CxRx 2 IC3907 4 1 1 IC3906 2 3 2 H BLK 7 CLP P DLY 4 10 BUFF Q3913 11 CN3901 (2/2) Y CLP P C CLP P IC3902 CN3902 (2/2) 5 4 3 IC3905 Q3909 CLAMP DELAY CONTROL BUFF Q3903 9 9 H SYNC SEP 8 V SYNC SEP 10 VIDEO F BUFF Q3910 SDI SEL 4 Q3902 +5V H SYNC SEP1 BUFF Q3912 14 +5V +5V H SYNC SEP2 B BOARD (2/2) CN422(2/2) Q3911 5 CN3901 (1/2) H SYNC 7 IC3902 V SYNC SEP Q3905,3907 12 14 13 V SYNC Signal Select BUFF Q3908 11 6 B Block (1/2) IC3908 5 COMP SYNC 5 BUFF Q3916 7 BUFF Q3914 CAPTION Y 8 SWITCH Signal Select, Sub CPU 1 BX Block 6 B2 (H/V SYNC GENERATOR) Q3915 Signal Amp B1 Block H/V, Sync Generator B2 Block BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B BOARD(2/2) CN411(2/2) GAIN CONT 12 DL403 DL400 PB IC302 IC4302 1 STBY 5V BUFF Q334 B Y C B BOARD(2/2) CN412(2/3) B BOARD(2/2) CN412(3/3) D 1 2 IC050 -5V REG BUFF Q411 IC4300 X501 +5V DL404 IC410 10 6 IC010 BUFF Q404 Y TP303 5 15 1 7 RESET SW Q501 13 IC302 IC300 63 SLOT ID B26 CLAMP Q367(2/2) IC305 CLAMP 7 5 CS OUT BX OE 48 IC502 9 B22 PB AMP CN401(2/2) 6 IC501 PR/R AMP Q365,366 5 Q402 EXT SYNC OE 47 IC307 10 IC302 TP401 OPTION Y AMP Y BUFF/AMP Q406-409 4 9 TO (2/2) BUFF Q333 15 1 9 Q302 RESET B R DL402 2 11 IC304 CLAMP 3 1 +5V T 3 5 3 IC301 14 12 IC301 IC304 CLAMP 7 5 TP301 PR/R BUFF Q301,303 CLAMP Q332(2/2) IC410 BUFF Q412 DL405 13 IC301 PB/B AMP Q330,331 BUFF Q405 G IC306 1 PB/B OUT Q202 SYNC A BUFF Q303 7 9 PR/P MA BOARD CN101 Y 11 IC303 CLAMP 3 1 5 TP302 14 13 IC300 IC303 CLAMP 7 5 +5V PB/B CLAMP Q302(2/2) B1 (SIGNAL AMP) CN401(1/2) IC300 CN301 10-3 10-3 B (2/2), C B (2/2), C B Block (2/2) C Block R SELECT B (2/2) ( SIGNAL RGB MATRIX ) 4 CN412(2/3) PR AMP Q451 BUFF Q452 12 13 11 IC400 1 2 7 C PR AMP 2 R AMP Q1300,1301 14 5 4 AMP Q460,461 BUFF Q462 AMP Q463 R BUFF Q1303 10 R IN R GAIN R BIAS 5 BUFF Q464 R OUT 41 BUFF Q1430 BUFF Q1431-1433 7 2 AMP Q2315-2317 BUFF Q2318 AMP Q2330-2322 BUFF Q2333 2 R OUT 2 R AMP Q730,731 BUFF Q732,733 4 G AMP Q750,751 BUFF Q752,753 6 B AMP Q770,771 BUFF Q772,773 R SW Q734 CLAMP Q1434 12 3 IK DET Q735 TP702 38 R C/O G OUT 36 BUFF Q1420 BUFF Q1421-1423 4 G OUT G SW Q754 CLAMP Q1424 3 BUFF Q485 5 AMP Q486 IC1302 BUFF Q487 12 6 IC1306 CLAMP 5 7 IC1301 G AMP Q1320,1321 14 13 11 12 2 CLAMP Q1322 5 4 B OUT 30 2 15 1 11 10 G BUFF Q1322 BUFF Q1410 BUFF Q1411-1413 TP703 B SW Q774 8 (FBT) 32 G DRV R OUT 41 IK DET Q775 IK BUFF Q1402 10 IK RTN 10 1 VP 1 33 G C/O IK MASK Q1401 4 3 B OUT CLAMP Q1414 G GAIN G BIAS 5 6 11 G IN 10 IC1308 3 IK DET Q755 IC1308 14 13 15 1 IC1302 IC1306 CLAMP 1 3 IC1308 IC1302 9 9 IK MASK Q1400 VP BUFF Q702 RV701 13 RV702 V BLK 22 9 5 IC1303 12 IC1307 CLAMP 5 7 IC1302 B AMP Q1340,1341 14 13 11 IC1307 CLAMP 1 3 6 5 SDA(1/2) 14 3 SCL(1/2) 15 4 1 2 9 10 26 B DRV H2 +B REG Q701 8 H2 7 H1 1 G2 3 160V J G BOARD CN604 27 B C/O CN303 4 3 1 H BLK 6 V BLK 4 AFC PLS 7 VD BLK 2 ABL ST 5V 1 STBY 5V +5V 3 HP 20 VP 18 9 PB LEVEL CLP2 23 IC1400 MONO-MULTI 10 Q2 A2 12 IC3407 1 7 2 RGB SW Y LEVEL (1/2) CAP CT H G BOARD CN502 IC4350 CAP L1/L2 CAP ON/OFF D/A CONV 9 6 14 7 15 3 2 1 R 5 13 IC3400 12 5 11 1 ON/OFF 2 RESET G 6 11 CV1 8 HP B 7 BOX 3 Q3402 MB BOARD CN1105 DC ADJ B BIAS C (RGB OUT) H BLK (1/2) CLP1 24 18 C/T G 3 Y IN G-Y/B 17 L1/L2 10 12 B IN 10 5 -5V 10 B2 BOARD CN3902(2/2) 1 B BUFF Q1343 IC1309 Q1304,1305 3 H1 CN701 15 B GAIN 5 4 2 11 10 G-Y/R IC3403 CAPTION DECODER CN422(2/2) VIDEO 1 IC1303 G2 IC1309 14 13 15 PR LEVEL 7 F 12 2 CLAMP Q1342 6 IC1309 IC1303 9 IC4301 D/A CONV V901 PICTURE TUBE 10 9 IC401 PB AMP BUFF Q2303 44 R DRV 4 BUFF Q466 1 AMP Q2300-2302 10 IC1304 3 9 6 15 1 TP701 CN702 CN304 2 11 10 IC1300 IC401 RGB MATRIX IC1304 14 13 15 1 BUFF Q465 5 2 CLAMP Q1302 IC1305 CLAMP 1 3 BUFF Q450 3 12 F2 PB BUFF Q453 IC1304 IC1300 F1 6 IC1305 CLAMP 5 7 IC1300 HV B1 BOARD CN402(2/2) B IC1300 CN411(2/2) Y G2 B1 BOARD CN401(2/2) G H1,2 B FROM(1/2) 10IC3400 9 5 IC3400 4 2 IC3400 1 13 IC3401 11 12 4 CUT OFF R CUT OFF G CUT OFF B DC ADJ MUTE 21 MUTE ACP S/DC SEL CN302 R SEL +12V GB SEL Q1463 OSD R IC4351 8 10 IC3401 6 5 IC3401 9 4 3 2 IC3401 1 8 6 D/A CONV OSD G OSD B 6 7 3 14 2 15 13 5 3 5 IC3407 6 3 4 BLK P 12 +5V -5V 4 -5V +12V 5 +12V R GAIN I G BOARD CN605 16 YS R BIAS SUB PIC(1/2) B/O DAC2(1/2) BRT DAC SW Q1462 PIC ABL Q1460 46 PIC BRT ABL Q1461 7 BRT CNT PIC DAC APER IC4352 CN307 D/A CONV 12 OSD R 1 OSD G 2 OSD B 3 3 4 OSD BLK 4 2 5 S PULSE1 6 S PULSE2 8 3 6 7 14 G GAIN G BIAS 5 B GAIN CN412(3/3) D APER B1 BOARD CN402(2/2) B BIAS 15 ACP R BUFF Q2382 IC2381 IC2382 SAMPLING 5 7 6 IC2383 LATCH D 2 2 15 5 Q 1 10 CK 1 1 IC2381 12 14 13 2 15 ACP R BUFF Q2381 1 10 ACP R BUFF Q2380 IC2381 12 14 BUFF Q2383 11 2 IC2382 SAMPLING IC2380 IC2380 13 11 5 4 3 9 Signal Select, RGB Matrix B Block (2/2) RGB Out C Block 10-4 10-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A G (1/2) G (1/2) G Block (1/2) L MB BOARD CN1101 CN501 AFC 7 H SYNC 1 V SYNC 2 V TIM 8 IC529(1/2) V BLK PULSE GEN T2502 HDT BUFF Q525 11 B2 Q2 10 1 IC507 HV OSC 6 H FLY SDA 5 41 SDA SCL 4 40 SCL 2 H FOC 17 H FOCAP 16 5 IC501 BUFF Q535 2 H BLK CONT 6 2 IC527 7 1 IC509 H BLK SYNC 4 H BLK 22 12 A2 Q2 10 5 B1 Q1 7 CX2 14 IC503(1/2) H SYNC PULSE GEN 2 IC526 4 1 CX1 5 B1 H DRIVE Q2505 BUFF Q2501,2502 H OUT Q2508 8 3 4 IC2502 3 1 DELAY IC515 PWM CONT HV IN 38 3 TIN H OUT COL 21 6 DTC Q504 Q523 1 7 15 FB2 IC502 5 V BLK CONT 7 6 IC528 5 3 12 A2 Q2 9 5 B1 Q1 7 CX2 14 2 IC522 1 CX1 SW Q533 IC503(2/2) V SYNC PULSE GEN 4 11 B2 V BLK 4 AFC 7 VD BLK 2 ABL CN2501 1 H DY+ 2 H DY+ 3 H DY- 4 H DY- 5 V DY+ 6 V DY- DY 4 T503 HRT Q514 10 5 9 5 11 2 10 1 9 3 L2501 HCC 4 17 INT+ 3 DRV 23 IC519 HV REG 2 OUT2 13 2 12 16 INT- 1 Q2 10 1 2 +B 7 INT+ +15V IC510 V BLK SYNC IC2501 1 PWM Q2503 OUT1 11 8 INT- V FOC 32 2 4 9 FB1 V BUC 23 6 B BOARD CN303 IC2504 H CENTER AMP T2501 HOT 2 IC528 H H BLK Q1 6 2 IC506,Q501 H LOCK 37 H SENTER BIAS Q2504 CN502 1 BUFF Q506,507 HV OUT Q513 2 IC529(2/2) PLL PULSE GEN DELAY Q532 6 Q1 PLL INH 3 A1 4 IC2503 V OUT V SYNC IN 33 7 +VIN VDC OUT 28 1 -VIN OUT 5 V OUT 29 V FLY 30 3 PUMP UP IC516 IC524 F.F BUFF Q521 EW OUT 31 5 4 D1 XRAY 15 4 3 9 CK BUFF Q505,508 DF AMP Q509-512 T501 DFT 9 Q4 15 11 1 8 5 D520 IC512 D/A CONV G2 AMP Q517,518 H BLK(F) 4 G2 (2/2) H BLK(R) 5 V BLK(B) 7 Q531 V BLK(T) 6 15 SCL SW Q534 4:3/16:9 10 BUFF Q2513 D531 H SIZE 3 Q529 50/60 1 T502 FBT T2503 CURRENT 14 SDA D2512 5 3 Q530 1 2 L2506 Q524 L2503 HLC L2504 HLC IC523 D506 1 D529 IC508 D/A CONV RELAY SW Q2511 VDL 9 HCENT 7 POWER 1 DGC 2 POWER (2/2) DGC (2/2) IC520 HV REG 5 3 1 2 7 FV FV1 17 D2514 18 Q2512 33.75K 4 1 6 IC514 HV PROT RY2501 HDL 10 15K 6 C BOARD PICTURE TUBE 3 13 HV 2 PROT 3 L2507 31.5K 5 14 15 D530 15 SCL HV 2 D532 1125/50 2 14 SDA 1 16 S-CAP ON/OFF Q2518 FV 11 FV2 CN503 1 IK DET 3 IK DET Q2519 S-CAP ON/OFF Q2514 IC523 D507 Q2515 5 IK 7 PROT 6 3 IC517 IK PROT 1 2 H/V OSC G (1/2) (DYNAMIC FOCUS ) BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A HV PROT Q520 10-5 10-5 HV PROT (2/2) H/V OSC, Dynamic Focus G Block (1/2) G (2/2), G1 G (2/2), G1 G Block (2/2) G1 Block G (2/2) (MAIN REG) T605 PIT 4 AC IN AC 100-240V 50/60Hz IC601 POWER FACTOR CONT CN603 LIVE NEUTRAL 10 CATHODE T602 3 1 VD 3 AC SENSE D609 1 DRA IN L SENSE 5 3 AC L IN 1 AC L OUT 17 AC L OUT 5 D602 AC RECT 9 3 +12V REG 17 +12V IC607 16 -12V REG 15 D625 ±6V RECT 2 VS 19 -12V +5V IC608 -5V +5V REG 14 Q608 VC1 14 10 -15V IC606 VC2 15 3 RESET T603 PFCT AC L IN D624 ±15V RECT VB 18 D635 LINE FILTER 1 Q605 IC602 MAIN SWITCHING VCC 9 +15V 18 ST 5V IC609 -5V REG RT 7 D626 13 12 LATCH Q603,604 THP601 8 D623 +B RECT 1 7 DGC 11 RY602 DGC PH603 +B FEED BACK RY601 DEGAUS DRIVE Q601,619 G2 (1/2) +15V Q609 D620 1 3 2 IC610 +B REG 2 3 STBY +5V 5 CN606 +12V 4 -12V 7 +6V 6 -6V 2 STBY +5V 1 5V SENSE 3 CN604 +160V 7 H1 8 H2 1 G2 2 CN608 5V SENSE 1 STBY +5V T OPTION J C BOARD CN701 O.C.P Q614 LATCH Q616,617 4 1 3 2 PROT Q615 LATCH Q611,612 PROT Q613 HV PROT (1/2) PROT Q621,622 CN607 5 -5V 1 1 D633 18V +5V 4 I B BOARD CN302 +B (1/2) 4 PH604 RFC & MAIN ON/OFF DGC SW (1/2) DC IN 3 10 RELAY DRIVE Q602 3 CN605 +12V 13 S901 POWER CN601 DGC 5 Q620 POWER ON/OFF Q618 T1601 SRT CN601 DC IN 5 POWER (1/2) G1 3 D1604 IC1601 SW Q1601,1602 D1606 D1603 5V CONTROL L1601 10 1 CN1602 1 STBY +5V 2 5V SENSE 9 D1605 18V 3 4 8 5 PH601 CTL FEED BACK 4 1 3 2 3 PH602 OVP FEED BACK 10-6 4 1 3 2 IC1602 STBY 5V REG 1 Main Regulator 2 5V OVP COMP Q1603 10-6 G Block (2/2) Main Regulator G1 Block BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A MA, MB MA, MB MA Block MB Block MAIN CPU MA ( PARALLEL I/O ) A BX BOARD CN001 T CN101 RESET 3 Q102 IC112 PARALLEL I/O SLAVE CPU RESET 54 PA0 PD7 29 TP105 SLOT1 8 OPTION SLOT2 9 OPTION SLOT3 10 TP106 TP103 IC104 SLOT RECEIVER IC101 MISO MOSI SCLK 4 8 10 5 IC101 6 5 4 6 IC101 3 2 1 CN103 TALLY(G) YA D901-905 CN901 TALLY(G) 2 TP102 8 1 2 3 4 TP101 LED DRIVE Q104,106 3 TALLY(R) TALLY(R) 3 IC1105 RS485 CONT CN1102 MISO A10 MOSI B10 SCLK A11 CS REM1 B6 4 CS IRQ REM1 A5 6 IRQ 2 D OUT 5 6 1 D IN +5V 6 5 3 PB1 4 3 64 PB0 2 1 5 PB3 PD4 24 4 8 9 4 PB2 PD6 28 5 PD5 27 6 D921 PROT CN421 PROT 1 STANDBY STANDBY 2 POWER POWER 3 1 D IN D0 25 B10 80 TXD1 D7 32 A11 82 SCK1 MOSI SCLK 79 SCK2 3 PHAI IC103 12 13 A13 6 BREQ 32 D0 D0-7 . 35 D7 D0-7 33 40 . A0-19 A19 43 A0-2 5 BACK SDA A12 IRQ REM1 A5 9 IRQ1 IRQ OPT B5 8 IRQ0 H SYNC A3 61 P75 V SYNC A4 59 P73 A0-17 A18 A14 SIO RESET B15 IC110 RESET BAT1 LITHIUM BATTERY 4 BAT WR 21 RESET RD 14 X101 20MHz WR 15 CS OPT B7 CS OSD1 B8 B5 3. 25 . 24 . A0-14 26 . 28 . 6 IRQ RD WR 43 WE A2 SLAVE TX TX 15 A17 A18 Y2 13 2 A1 3 A2 4 CS2 RX 14 9 A 15 13 LOAD C 2 D 3 IC1104 4 3 E 4 11 SCLK F 5 G 6 CS REM2 44 RD 43 WR 8 11 9 QH 27 WE 10 OE A7 14 CN931 CN1106 TXD 6 6 TXD RXD 8 8 RXD 2 RTS 3 3 RTS H 7 REM1 9 REM2 TP117 REM4 CN1107 REMOTE1 REM5 REM6 REM7 6 REM8 R OUT 19 23 TRE 25 SIN 24 SCLK CS OSD1 45 CS CS REM1 CS REM2 CS REM2 CS OPT CS OPT CS OSD1 CS OSD1 CS OSD2 CS OSD2 11 PC0 K 16 PC5 HC BOARD CN2 12 PC1 IC1104 12 13 12 H SYNC A9 B14 62 PA6 MASTER TX A15 63 PA7 5 RESET CN105 2 3 CS OSD2 6 TP1101 1 7 RXD CN102 RXD 7 2 RXD TXD CN101 3 RXD TXD 8 5 7 6 8 TXD 2 CONTORL UNIT 8 TXD 23 TRE R OUT 19 25 SIN G OUT 18 3 9 26 CS A9 1 A13 12 H SYNC SCL A12 13 V SYNC V SYNC MODULAR 5 IC1100 CN1105 4 6 8 IC1100 10 9 2 IC1100 1 3 11 IC1100 13 12 1 OSD R 2 OSD G 3 OSD B 4 OSD BLK 8 SAMPL PLS2 6 SAMPL PLS1 TP1108 TP1109 B OUT 20 I OUT 17 8 DOCKI SDA COMP SYNC A3 VOB1 16 IC1110 OSD 24 SCLK HD IC113 RS422 DRIVE IC1101 3 2 1 D14H1 MODEL TP115 B OUT 20 13 V SYNC SIO RESET B15 14 PC3 CS OSD2 TP116 8 DOCKI 13 PC2 SLAVE TX G OUT 18 26 CS B8 D14H5 MODEL 5 CS3 CS REM1 5 REM3 CN1109 IC1101 8 9 10 Y3 12 5 RESET A4 5 CN1101 V SYNC H SYNC 2 1 SCL 4 SDA 5 L AFC 7 G BOARD CN501 VTIM 8 CN1100 V SYNC H SYNC E B BOARD CN308 3 2 COMP SYNC 1 5 SCL SDA 6 MB (REMOTEOSDCONTROL) Main CPU, Parallel I/O MA Block Remote Control OSD MB Block BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A OPTION CN932 5 7 IC1107 OSD 2 IC102 7 1 10-7 10-7 1 YC 7 IC1112 REMOTE2 DRIVE 12 LATCH B 1 22 OE 6 RTS 13 IC1102 13 12 X1100 3.6864MHz WR 1 A0 2 RE IC1104 MASTER/ SLAVE SW 10 19 21 . A14 23 . CN1104 OUT 3 DE 8 9 TP1107 TP1100 D0 13 . D0-7 D7 15 5 DO/RI 7 IC1109 RS232 I/F IC1102 1 2 1 9 DO/RI 6 1 RO A14 11 A0 4 DI B14 2. 26 . 1 30 14 OE 48 IC109 ADDRESS SELECTOR TXD2 77 A7 12 CE 19 . D0 21 . D0-7 D7 24 . 10 WR A16 B6 34 . 3 15 . 17 . RD 84 EXTAL RXD2 78 CS REM2 42 A16 A0 M/S SEL RD A15 CS REM1 IRQ OPT 4 CS 6 REMOTE1 MASTER TX A15 20 CE TP104 1 XTAL 31 . 11 A-1 4. A0 3 A17 RD RST 2 CS 5 IC107 13 12 A19 76 P91 M/S SEL B7 10 X1 46 IC111 SRAM IC108 PROGRAM ROM 54 4 P11/E IC103 10 11 CS OPT 39 A0 2 RE IC1106 RS485 REM1 3 SCLK 81 RXD1 A10 CN1103 IN DO/RI 7 3 DE IC1108 RS232C CONT TP1106 D923 5 DO/RI 6 1 RO RX 14 2 D OUT 30 MISO 4 DI TP1102 10 X1 D922 49 PE0 IC106 MAIN CPU YB 9 IC1103 RS485 REM1 TP1103 TX 15 3 SCLK IC1104 IC103 SLOT DRIVER CN102 SDA 2 TP107 PD1 21 9 LED DRIVE Q103,105 G B BOARD CN307 BVM-D14H5 HA Block HB Block HC Block K MA BOARD CN105 HA HC IC1 MAIN CPU IC13 RS422 DRIVE CN2 3 8 R IN RXD TXD 9 7 RIN 7 5 DOUT TXD 2 6 DOUT ROUT 2 29 RXD1 TP4 28 TXD1 DIN 3 HA, HB, HC BVM-D14H5 HA (2/2) IC12 BUS SHIFT TP5 TP3 RXD HA, HB, HC CN5 CN201 RXD0 26 16 4 5 MISO MISO 5 TXD0 25 6 14 4 MOSI MOSI 4 TP204 SCK0 27 8 12 3 SCLK SCLK 3 TP203 2 18 6 CE2 CE2 6 TP202 (1/2) SW OUT Q201 IC201 S/P CONV P1 11 S201 POWER P2 10 S202 DEGAUSS P3 9 S203 NUM-1 P4 8 S204 NUM-2 P5 7 S205 NUM-3 14 CLK P6 5 S206 NUM-0 15 STB P7 4 S207 NUM-4 13 DATA P8 3 S208 NUM-5 P9 2 S209 NUM-6 P10 1 S210 NUM-CLEAR P11 23 S211 NUM-7 P12 22 S212 NUM-8 P13 21 S213 NUM-9 P14 20 S214 NUM-ENTER P1 11 S215 ENCODER 0 P2 10 S216 ENCODER 1 P3 9 S217 ENCODER 2 P4 8 S218 ENCODER 3 P5 7 S219 MENU P6 5 S220 ENTER P7 4 S221 UP P8 3 S222 DOWN P1 11 S107 COMB/B P2 10 S108 F1/F3 P3 9 S109 F2/F4 P4 8 S110 ADD/MARKER CN4 S231 CONTRAST CN202 10 9 ENCODER 3 ENCODER 3 S232 BRIGHT 8 7 ENCODER 2 ENCODER 2 IC11 BUFFER IC9 CN3 EN 3A 3 5 6 2 D7 Q7 19 64 D7 EN 3B 4 3 4 3 D6 Q6 18 63 D6 EN 2A 5 1 2 4 D5 Q5 17 62 D5 EN 2B 6 9 8 5 D4 Q4 16 61 D4 EN 1A 7 11 10 6 D3 Q3 15 60 D3 TMCI1 20 EN 1B 8 13 12 7 D2 Q2 14 59 D2 TMO1 21 IC10 S233 CHROMA EN 0A 6 5 ENCODER 1 ENCODER 1 EN 0B 9 5 6 8 D1 10 3 4 9 D0 11 10 11 CLK S234 PHASE Q1 13 58 D1 Q0 12 57 D0 1 OE 4 3 ENCODER 0 ENCODER 0 +12V IC2 RESET R RES 9 10 5 15 5 MISO 13 7 4 MOSI 11 9 3 SCLK 17 3 6 CE1 X1 ENA ENB 1 19 IC3 ADDRESS DECODER A3 53 1 A A4 52 2 B A5 51 3 C A6 50 4 G2A IOS 34 5 G2B A7 49 6 G1 TP6 Y0 15 IC202 S/P CONV SO 12 RD 37 13 DATA 14 CLK 15 STB D223-226 P9 2 P10 1 P11 23 P12 22 P15 19 P16 17 CN202 MISO 5 MOSI 4 SCLK 3 CE1 6 IC102 S/P CONV LED SW Q202,203 SW OUT Q103 13 DATA 14 CLK 15 STB D127-130 P9 2 P10 1 P11 23 P12 22 SO 12 IC101 S/P CONV 13 DATA 14 CLK 15 STB P1 11 S101 SHIFT P2 10 S102 10:9 P3 9 S103 SYNC P4 8 S104 B ONLY P5 7 S105 MONO/R P6 5 S106 APT/G D121-126 P9 2 P10 1 P11 23 P12 22 P13 21 HB P14 20 Switch P15 19 HA Block P16 17 LED SW Q101,102 Serial to Parallel Converter HB Block Main CPU HC Block 10-8 10-8 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A Section 11 Diagrams 1 Note: [Measuring conditions, voltage and waveform] • Parts marked “ * ” differ according to the model/destination. Refer to the mount table for each function. • The parts marked “ # ” on schematic diagrams are not mounted. • All capacitors are in µF unless otherwise noted. pF: µµF 50WV or less are not indicated except for electrolytics. • All electrolytics are in 50 V unless otherwise specified. • : fusible resistor • : nonflammable resistor • ∆ : internal component • : panel designation and adjustment for repair • Caution when replacing chip parts New parts must be attached after removal of the chip. Be careful not to heat the minus side of a tantalum capacitor, because it is easily damaged by the heat. • A voltage value is the reference value between the measurement point and the earth, when the RGB color bar signal is received (digital multi-meter used: 10 M ohms/V DC). • Unit of voltage is V (volt). : B+line • : B– line • Voltage variations may occur due to normal production tolerances. • RGB color bar signal. • Circled numbers indicate the reference waveform. • : Signal path. Reference information RESISTOR RN RC FPRD FUSE RS RB RW : METAL FILM : SOLID : NONFLAMMABLE CARBON : NONFLAMMABLE FUSIBLE : NONFLAMMABLE METAL OXIDE : NONFLAMMABLE CEMENT : NONFLAMMABLE WIREWOUND : ADJUSTMENT RESISTOR COIL LF-8L : MICRO INDUCTOR CAPACITOR TA PS PP PT MPS MPP ALB ALT ALR : TANTALUM : STYROL : POLYPROPYLENE : MYLAR : METALIZED POLYESTER : METALIZED POLYPROPYLENE : BIPOLAR : HIGH TEMPERATURE : HIGH RIPPLE 2 The components identified marked ! are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. NOTE: The circuit indicated as shown on the left contains high voltages of over 600 Vp-p. Take care to avoid electric shock during inspection or repair work. 3 • The components marked in this schematic diagram have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. • When replacing components marked , make the necessary adjustments indicated. If results do not meet the specified value, change the component marked and repeat the adjustment until the specified value is achieved. • When replacing a part shown in the table below, be sure to perform the related adjustment. 4 5 11-1 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-1 E F G H Frame Frame 11-1. Frame Schematic Diagrams CN701 8P :VH 1 CN703 FASTEN CN202 10P WHT ELCO CN604 8P WHT :VH CN603 3P WHT :VH CN702 10P WHY-L :S-MICRO CN304 10P WHT S-MICRO 2 CN901 3P WHT-L PH CN303 7P WHT S-MICRO CN931 8P WHT :PH CN921 4P BOARD IN CN602 7P WHT :VH CN605 6P RED S-MICRO CN302 6P RED S-MICRO CN201 6P WHT ELCO CN601 3P WHT :MINI CN502 7P WHT S-MICRO CN101 6P YEL ELCO CN2501 6P WHT MINI CN308 9P RED S-MICRO CN606 8P WHT S-MICRO 3 CN307 9P WHT S-MICRO CN503 2P WHT S-MICRO CN1 9P WHT-(L) ELCO CN301 11P WHT S-MICRO 4 CN501 12P WHT S-MICRO CN2 9P WHT ELCO CN801 8P WHT-(L) S-MICRO CN3 10P WHT ELCO CN805 8P WHT-(L) S-MICRO CN105 9P WHT-(L) S-MICRO CN1105 9P WHT-(L) S-MICRO CN103 7P RED S-MICRO CN806 10P WHT-(L) S-MICRO CN1100 9P RED-(L) S-MICRO CN1106 7P BLK-(L) S-MICRO CN4 6P WHT ELCO CN101 10P WHT-(L) S-MICRO 5 CN5 6P WHT ELCO CN1101 12P WHT-(L) S-MICRO CN1109 6P 11-2 A B C D 11-2 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H BX BX 11-2. Schematic Diagrams and Printed Wiring Boards 1 BX BOARD B A [BX BOARD] C C B A * : B SIDE D101 D102 D201 D202 D301 D302 D401 D402 D501 A-1 C-2 A-2 C-3 A-3 C-3 A-4 C-3 C-5 IC010 IC050 IC501 IC502 IC503 B-1 C-1 B-4 C-4 B-5 Q101 Q102 Q103 Q201 Q202 Q203 Q301 Q302 Q303 Q401 Q402 Q403 Q404 Q501 A-1 B-2 C-2 A-2 B-3 C-3 A-3 B-4 C-3 A-4 B-4 C-3 B-5 C-4 TP001 TP010 TP101 TP201 TP301 TP401 B-2 B-4 C-2 C-3 C-3 C-3 1 1 2 2 3 3 3 4 4 5 5 BX –A SIDE– BX –B SIDE– SUFFIX: -11 SUFFIX: -11 11-3 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A 2 B C D 4 5 11-3 E F G H BX (1/2) BX (1/2) BX BOARD WAVEFORMS 1 1 2.0Vp-p (H) 2 C014 100 16V :HT TB001 Q102 DTA144 EKA C103 47 16V :BP D101 MA111 C101 10p R101 CH:CHIP 75 1/2W :RN 1.4Vp-p (H) 3 C102 22p CH:CHIP C104 0.1 16V B:CHIP C054 100 16V :HT 2 C201 10p R201 CH:CHIP 75 1/2W :RN 1.4Vp-p (H) 4 C015 0.1 25V F:CHIP R104 2.2k :CHIP R106 22 :CHIP R103 100 :CHIP R107 100 :CHIP C055 0.1 25V F:CHIP R102 Q101 47k :CHIP 2SA146 2 C203 47 16V :BP 5 R203 100 :CHIP D201 MA111 R109 33 :CHIP TP101 R108 100k :CHIP C402 C401 8p 22p CH:CHIP CH:CHIP C016 0.1 25V F:CHIP C020 0.1 25V F:CHIP R204 2.2k :CHIP Q203 2SC354 5 R206 22 :CHIP C204 0.1 16V B:CHIP C056 0.1 25V F:CHIP R205 100k :CHIP R202 47k :CHIP C060 0.1 25V F:CHIP R207 100 :CHIP D202 MA111 C206 0.01 R209 B:CHIP 33 :CHIP TP010 TP201 R208 100k :CHIP 0.6Vp-p (H) 6 C106 0.01 B:CHIP D102 MA111 C059 0.1 25V F:CHIP R105 100k :CHIP Q202 DTA144 EKA 3 Q103 2SC354 5 C202 22p CH:CHIP C30 2 C301 22p 10p R30 1 CH:CHIP CH:CHI P 75 1/2 W :RN-CP 0.9Vp-p (H) C019 0.1 25V F:CHIP Q201 2SA146 2 R401 75 1/2W :RN 0.6Vp-p (H) Q302 DTA144 EKA C303 47 16V :BP R303 100 :CHIP D301 MA111 R304 2.2k :CHIP C021 0.1 25V F:CHIP Q303 2SC354 5 R307 100 :CHIP R306 22 :CHIP C304 0.1 16V B:CHIP C057 0.1 25V F:CHIP R305 100k :CHIP R302 47k :CHIP 4 C017 0.1 25V F:CHIP D302 MA111 C306 0.01 B:CHIP C061 0.1 25V F:CHIP R309 33 :CHIP TP301 R308 100k :CHIP Q301 2SA146 2 Q401 2SC241 2K R403 1k :CHIP C404 0.1 16V B:CHIP R402 47k :CHIP R408 100k :CHIP R404 100k :CHIP C403 47 16V :BP R406 22 :CHIP D401 MA111 R405 2.2k :CHIP C018 0.1 25V F:CHIP TP401 D402 MA111 Q404 DTA144 EKA R407 100 :CHIP R410 100k :CHIP C058 0.1 25V F:CHIP Q402 DTC144 EKA R409 33 :CHIP C022 0.1 25V F:CHIP Q403 2SA103 7AK C062 0.1 25V F:CHIP 5 11-4 A B C D 11-4 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H BX (2/2) BX (2/2) MB89613R-651 (IC501) 1 X0 23 X1 24 TIME BASE TIMER OSC 8 BIT PMW TIMER 8 BIT PULSE WIDTH COUNT TIMER CLOCK CONTROL C010 C011 100 0.1 16V 25V :HT F:CHIP IC010 BA05FP C012 100 16V :HT P00/AD0 P01/AD1 P02/AD2 P03/AD3 P04/AD4 P05/AD5 P06/AD6 P07/AD7 P10/A08 P11/A09 P12/A10 P13/A11 P14/A12 P15/A13 P16/A14 P17/A15 C013 0.1 25V F:CHIP TP001 C050 C051 100 0.1 16V 25V :HT F:CHIP IC050 LM2990CX C052 100 16V :HT C053 0.1 25V F:CHIP R511 R510 R509 100k 100k 100k :CHIP :CHIP :CHIP R501 100k :CHIP MOD0 21 MOD1 22 IC502(1/4) TC74VHC125F 14 9 R503 100 :CHIP 10 IC502(2/4) TC74VHC125F 3 2 R504 100k :CHIP IC502(3/4) TC74VHC125F 12 R505 100 :CHIP X501 IC501 MB89613R-651 1 R506 100k :CHIP P27/ALE P26/RD P25/WR P24/CLK P23/RDY P22/HRQ P21/HAK P20/BUFC 8 7 R502 100 :CHIP 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 RESET(WDT) 16 BIT TIMER COUNTER 55 P34/EC 54 P33/SI1 8 BIT SERIAL 1 53 P32/SO1 52 P31/SCK1 C-MOS I/O PORT C-MOS I/O PORT 51 P30 50 VSS 3 P47/S12 2 P46/SO2 8BIT SERIAL 2 BUZZER OUT 64 P44/BZ 63 P43 OPEN DRAIN I/O PORT 62 P42 61 P41 1 P45/SCK2 5 P51 6 P52 EXT. BUS INTERFACE OPEN DRAIN OUT PORT 7 P53 8 P54 9 P55 10 P56 11 P57 C-MOS OUT PORT 30 31 32 33 12 VCC 13 N.C. 14 VSS R512 100k :CHIP RAM R513 100k :CHIP R514 100k :CHIP R515 100k :CHIP 11 1 15 P60/INT0 CPU F2MC-8L R507 100 :CHIP 2 60 P40 4 P50 26 27 28 29 58 P36/WTO 57 VCC 56 P35/PWC BUS RST 20 59 P37/PTO INTERNAL CN001 64P EXT. INTERRUPUT 16 P61/INT1 3 17 P62/INT2 18 P63/INT3 19 P64 I/O PORT ROM 6 5 4 IC502(4/4) TC74VHC125F D501 RD6.2SB R516 4.7k :CHIP R508 100k :CHIP X25040S (IC503) Q501 DTC144EKA STATUS REGISTER C503 0.1 25V F:CHIP FL501 R517 100k :CHIP IC503 X25040S WRITE PROJECT LOGIC 512 BYTE ARRAY X DECODE LOGIC 32 32X32 R518 100k :CHIP CS 1 SO 2 COMMAND DECODE AND CONTROL LOGIC 32 8 VCC 7 HOLD 6 SCK 5 SI 4 32X32 FL502 64 64X32 FL503 C501 C502 100 0.1 16V 25V :HT F:CHIP WP 3 VSS 4 WRITE CONTROL AND TIMING LOGIC 4 8 Y DECODE DATA REGISTER 5 11-5 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-5 E F G H B B [B BOARD] 1 2 3 4 5 * : B SIDE D1400 D1401 D1402 D1403 D1404 D1405 D2345 D2346 D2347 D2348 D2349 D2355 D2356 D2357 D2358 D2359 D2365 D2366 D2367 D2369 D2370 D3301 D3302 D3307 D3308 D4401 C-3 D-4 D-3 C-3 * B-3 * C-3 * A-5 * B-4 * B-5 * A-5 * B-5 * C-5 * B-4 * B-5 * C-5 * C-4 * D-5 * B-4 * B-5 * D-5 * D-4 * B-4 * A-3 * D-4 * D-4 * D-3 IC300 IC301 IC302 IC303 IC304 IC305 IC306 IC307 IC308 IC400 IC401 IC1300 IC1302 IC1303 IC1304 IC1305 IC1306 IC1307 IC1308 IC1309 IC1400 IC1401 IC2345 IC2355 IC2365 IC2380 IC2381 IC2382 IC2383 IC3301 IC3400 IC3401 IC3403 IC3404 IC3405 IC3406 IC3407 IC4300 IC4301 IC4302 IC4350 IC4351 IC4352 A-1 A-2 A-2 A-1 A-2 A-2 B-1 B-1 B-2 B-2 B-1 C-2 C-2 C-1 D-2 C-2 C-2 C-1 D-2 D-1 C-2 * C-3 A-4 B-4 D-4 D-3 D-3 D-3 D-2 A-3 D-1 D-1 D-1 D-4 D-2 * B-3 C-2 A-1 C-1 B-3 D-2 D-3 B-3 Q300 Q301 Q302 Q303 Q304 Q330 Q331 Q332 Q333 Q334 Q365 Q366 Q367 Q368 Q369 Q450 Q451 Q452 Q453 A-1 * A-1 A-1 A-1 * B-1 A-2 * A-2 A-2 A-2 * B-1 A-2 * A-2 A-2 A-2 * B-2 B-2 * C-2 * B-1 Q460 Q461 Q462 Q463 Q464 Q465 Q466 Q485 Q486 Q487 Q1300 Q1301 Q1302 Q1303 Q1304 Q1305 Q1320 Q1321 Q1322 Q1323 Q1340 Q1341 Q1342 Q1343 Q1400 Q1401 Q1402 Q1410 Q1411 Q1412 Q1413 Q1414 Q1420 Q1421 Q1422 Q1423 Q1424 Q1430 Q1431 Q1432 Q1433 Q1434 Q1460 Q1461 Q1462 Q1463 Q2300 Q2301 Q2302 Q2303 Q2315 Q2316 Q2317 Q2318 Q2330 Q2331 Q2332 Q2333 Q2345 Q2346 Q2355 Q2356 Q2365 Q2366 Q2375 Q2376 Q2377 Q2380 Q2381 Q2382 Q2383 Q3301 Q3302 Q3303 Q3304 Q3305 Q3306 Q3307 Q3308 Q3309 Q3310 Q3311 Q3312 Q3313 Q3314 Q3315 Q3316 Q3317 Q3318 Q3319 Q3402 * B-1 * B-1 B-2 * C-1 * C-2 B-2 * C-1 B-1 C-1 * C-1 * C-2 * C-2 * D-2 * D-2 * D-1 D-1 * C-2 * C-2 * D-2 * D-2 * C-1 * C-1 * D-1 * D-1 * C-3 C-3 * C-3 * C-3 C-3 C-4 C-3 C-4 * C-3 C-3 C-4 C-3 C-4 * B-3 B-3 B-4 B-3 B-4 * D-3 D-4 C-3 * C-3 B-4 B-4 B-4 B-4 C-4 C-4 C-4 B-4 D-4 C-4 C-4 C-4 * A-5 A-4 * C-5 C-5 * D-5 D-5 * D-5 C-4 * B-5 D-3 D-3 D-3 * D-3 * A-3 A-4 * A-4 A-3 A-4 A-3 * A-4 * A-4 * B-3 A-3 A-3 * B-3 * A-3 A-3 * A-3 * A-3 A-3 * A-3 * A-3 D-1 TP300 TP301 TP302 TP303 TP304 TP310 TP1300 TP1301 TP1302 TP2345 TP2355 TP2365 TP3301 A-1 A-1 A-1 B-1 B-2 A-1 C-2 C-2 C-1 A-4 B-4 C-4 A-3 B BOARD A B C D C B A 1 1 2 2 3 3 4 4 5 5 11-6 A D B C D B –A SIDE– B –B SIDE– SUFFIX: -11 SUFFIX: -11 11-6 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H B (1/4) B (1/4) 1 IC300 MC74HC4053FEL SWITCH R3301 1.5k :CHIP C300 0.01 F:CHIP C377 47 16V :HT-CP R3299 100 :CHIP R305 1k :RN-CP Q300 C302 R304 2SA1462 # # CH:CHIP :RN-CP CLAMP R300 1k R306 :CHIP R302 100 1.8k :CHIP :RN-CP C301 0.01 F:CHIP R307 1.2k :RN-CP IC300 MC74HC4053FEL SWITCH R308 100 :CHIP Q302 IMX2 CLAMP R309 1k Q301 :CHIP 2SC3545 CLAMP R313 1M :RN-CP C305 0.01 B:CHIP R311 150 :CHIP R310 1k :CHIP IC300 MC74HC4053FEL SWITCH R315 330k :RN-CP C304 0.047 B:CHIP TP302 C307 2.2 F:CHIP IC303 TL082CPS CLAMP R312 IC303 10k :RN-CP TL082CPS CLAMP R318 1.5k :CHIP R319 R320 15k 27k :RN-CP :RN-CP C306 0.01 F:CHIP C331 # CH:CHIP TP310 R333 3.3k :RN-CP TP300 R330 1k :CHIP R337 1.2k :RN-CP IC301 MC74HC4053FEL SWITCH R335 1k :RN-CP C330 # CH:CHIP R334 # :RN-CP Q330 2SA1462 CLAMP R324 2.2k :CHIP IC306 C310 CXA1521M 0.01 Y AMP F:CHIP R343 1M :RN-CP R341 100 :CHIP Q331 R339 1k 2SC3545 :CHIP CLAMP R336 100 :CHIP R332 1.8k :RN-CP R338 100 :CHIP Q332 IMX2 CLAMP R340 1k :CHIP R356 220 :CHIP C332 0.047 B:CHIP C333 0.01 B:CHIP C336 0.01 F:CHIP IC301 MC74HC4053FEL SWITCH IC301 MC74HC4053FEL SWITCH R347 100 :CHIP R346 220 :CHIP R345 560k :RN-CP R344 10k :RN-CP R342 10k IC304 :RN-CP TL082CPS CLAMP C335 2.2 F:CHIP R348 1.5k :CHIP C337 0.01 F:CHIP C334 0.01 F:CHIP R354 100 :CHIP C366 # CH:CHIP R368 3.3k :RN-CP C386 1000 6.3V R366 100 :CHIP C387 1000 6.3V R372 1.2k :RN-CP R370 1k :RN-CP IC302 MC74HC4053FEL SWITCH C365 # CH:CHIP Q365 2SA1462 CLAMP R373 100 :CHIP Q367 IMX2 CLAMP R378 1M :RN-CP C368 0.01 B:CHIP R376 100 :CHIP R365 R367 1k 1.8k :CHIP :RN-CP R371 100 :CHIP R375 1k :CHIP Q366 R374 1k 2SC3545 :CHIP CLAMP R381 220 :CHIP R380 560k :RN-CP IC307 C340 CXA1521M PB AMP 0.01 F:CHIP R349 R350 22k 200k :RN-CP :RN-CP R391 220 :CHIP C367 0.047 B:CHIP IC302 MC74HC4053FEL SWITCH R382 100 :CHIP IC305 TL082CPS CLAMP C369 0.01 F:CHIP R377 IC305 10k :RN-CP TL082CPS CLAMP C370 2.2 F:CHIP R383 1.5k :CHIP C372 0.01 F:CHIP R352 # R355 2.2k :CHIP C376 0.01 F:CHIP TP304 IC308 C375 CXA1521M PR AMP 0.01 F:CHIP R384 R385 22k 220k :RN-CP :RN-CP R390 2.2k :CHIP 3 R386 R387 56k # :RN-CP C374 2.2 16V F:CHIP R4317 220 :CHIP C450 10 16V :HT-CP R455 680 :RN-CP R458 100 :CHIP R450 100 :CHIP Q450 2SC2412K BUFFER R456 4.7k :CHIP Q453 2SA1462 BUFFER R482 100 :CHIP IC400 CXA1211M PB AMP C462 0.01 F:CHIP R462 6.8k :RN-CP R466 3.3k :RN-CP R463 4.7k :RN-CP C461 22 6.3V :HT-CP R460 6.8k C464 :RN-CP 0.01 F:CHIP C460 22 6.3V :HT-CP R461 C463 4.7k 0.01 F:CHIP :RN-CP R468 680 :CHIP C465 Q465 10 16V 2SA1037K :HT-CP BUFFER R478 4.7k :CHIP C466 10 16V :HT-CP R469 680 :CHIP R464 2.4k :RN-CP R451 1k :CHIP R472 100 :CHIP R465 5.1k :RN-CP Q461 2SC3545 AMP Q460 2SA1462 Q466 AMP 2SA1037K BUFFER R467 820 :RN-CP R473 1k :CHIP R459 2.2k :CHIP C452 0.01 F:CHIP R488 4.7k :RN-CP R485 C489 6.8k 0.01 :RN-CP F:CHIP C485 22 6.3V :HT-CP R480 100 :CHIP R4300 10k :CHIP R4309 R4308 10k 10k :CHIP :CHIP R4316 220 C4303 :CHIP 0.01 F:CHIP R4315 1k :CHIP IC4301 CXA1875AM-T4 D/A CONVERTER R4312 10k :CHIP R4306 10k :CHIP R4307 10k :CHIP R4320 2.2k :CHIP R4313 10k :CHIP 4 IC4302 CXA1875AM-T4 D/A CONVERTER R484 33 R475 680 :RN-CP R477 560 :RN-CP R481 2.2k :CHIP C468 0.01 F:CHIP C488 0.01 F:CHIP C490 10 16V :HT-CP R489 100 :CHIP R495 4.7k :CHIP Q485 2SC2412K BUFFER R493 680 :RN-CP Q486 2SC3545 AMP R491 680 :RN-CP R497 100 :CHIP C491 0.01 F:CHIP Q487 2SC3545 BUFFER 5 R499 150 R490 1k :CHIP R486 2.7k :RN-CP R492 680 :RN-CP R494 560 :RN-CP R498 2.2k :CHIP C494 47 16V :HT-CP 11-7 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A B C4302 0.01 F:CHIP IC4300 CXA1875AM-T4 D/A CONVERTER R4310 220 :CHIP C467 0.01 F:CHIP Q464 2SC3545 BUFFER C492 0.01 F:CHIP A R4311 220 :CHIP R4314 10k :CHIP R487 6.8k :RN-CP C487 0.01 F:CHIP C486 22 6.3V :HT-CP R4303 R4302 10k 10k :CHIP :CHIP R4301 10k :CHIP R479 4.7k :CHIP IC401 CXA1211M PR AMP R4304 220 :CHIP C4300 0.01 F:CHIP Q462 2SC2412K BUFFER R476 680 :RN-CP Q463 2SC3545 AMP R474 680 :RN-CP R4305 220 :CHIP C454 47 16V :HT-CP R457 150 R453 R454 820 560 :RN-CP :RN-CP R471 3.3k :CHIP R470 1k :RN-CP Q451 2SC3545 AMP R452 680 :RN-CP C451 0.01 F:CHIP Q452 2SC3545 BUFFER Q369 2SC3545 BUFFER R389 100 :CHIP R388 47k :CHIP L300 100µH R483 560 :RN-CP 2 C339 2.2 16V F:CHIP C373 22 6.3V :BP-CP Q368 2SC3545 BUFFER R379 10k :RN-CP R369 # :RN-CP C371 0.01 F:CHIP IC302 MC74HC4053FEL SWITCH Q334 2SC3545 BUFFER TP303 R353 47k :CHIP Q333 2SC3545 BUFFER IC304 TL082CPS CLAMP C341 0.01 F:CHIP C338 22 6.3V :BP-CP R351 56k :RN-CP CN303 7P WHT :S-MICRO Q304 2SC3545 BUFFER R323 100 :CHIP C309 0.01 F:CHIP R331 100 :CHIP CN302 6P RED :S-MICRO C311 0.01 F:CHIP R321 47k :CHIP Q303 2SC3545 BUFFER R314 10k :RN-CP R325 330 :CHIP R317 100 :CHIP R316 220 :CHIP R322 18k :RN-CP C308 22 6.3V :BP-CP C312 22µ 6.3V :HT-CP TP301 CN301 11P WHT :S-MICRO C303 # CH:CHIP R301 100 :CHIP R3300 100 :CHIP C378 47 16V :HT-CP R303 3.3k :RN-CP Q3301 2SA1037K C D 11-7 E F G H B (2/4) B (2/4) 1 R2303 270 :CHIP R2301 4.7k :CHIP Q2301 2SC3454 R2302 22 :CHIP Q2302 2SA1462 R2307 100 :CHIP C2351 C2310 C2311 47 0.01 16V 0.01 F:CHIP :HT-CP F:CHIP C2300 5p CH:CP R2314 33 :CHIP TP2345 R2300 100 :CHIP R2309 100 :CHIP R2318 270 :CHIP R2316 4.7k :CHIP Q2315 2SA1462 Q2316 2SC3545 R2319 560 :RN-CP R2329 33 :CHIP TP2355 Q2318 2SA1642 R2323 1.8k :CHIP C2363 C2364 47 C2353 16V 0.01 0.01 F:CHIP :HT-CP F:CHIP Q2332 2SA1462 R2337 100 :CHIP R2340 1k :CHIP C2330 9p CH:CHIP TP2365 R2344 33 :CHIP R2339 100 :CHIP Q2331 2SC3545 Q2330 2SA1462 R2325 1k :CHIP R2324 100 :CHIP R2320 470 :RN-CP R2332 22 :CHIP R2330 100 :CHIP C2361 47 C2362 C2352 16V 0.01 0.01 F:CHIP :HT-CP F:CHIP Q2317 2SA1642 C2315 7pF CH:CHIP R2333 270 :CHIP R2331 4.7k :CHIP R2308 1.8k :CHIP R2322 100 :CHIP R2317 22 :CHIP R2315 100 :CHIP Q2303 2SA1462 R2305 470 :RN-CP R2304 560 :RN-CP Q2300 2SA1462 2 R2310 1k :CHIP R2335 470 :RN-CP R2334 560 :RN-CP Q2333 2SA1462 R2338 1.8k :CHIP 3 CN304 10P WHT :S-MICRO R2384 100 :CHIP R2382 100 :CHIP R2380 100 :CHIP C2386 0.01 F:CHIP Q2382 2SC2412K BUFFER 3 2 Q2381 2SC2412K BUFFER IC2380(1/3) MC74HC4053AFT SWITCH IC2380(2/3) MC74HC4053AFT SWITCH Q2380 2SC2412K BUFFER 16 C2383 0.01 F:CHIP C2390 0.01 F:CHIP C2388 0.01 F:CHIP IC2382(2/2) LM393PS-E20 SAMPLING R2388 10k :CHIP R2390 2.2k :CHIP R2393 2.2k :CHIP 1 R2389 10k :CHIP IC2382(1/2) LM393PS-E20 SAMPLING Q2383 2SC2412K BUFFER R2392 10k :CHIP 8 5 7 2 4 15 14 12 1 13 R2386 100 :CHIP IC2381(2/3) MC74HC4053AFT SWITCH 2 10 6 4 C2384 0.001µF B:CHIP 15 1 R2381 2.2k :CHIP R2383 2.2k :CHIP 6 11 7 R2385 2.2k :CHIP 8 R2387 2.2k :CHIP C2387 0.01 F:CHIP R2391 10k :CHIP C2385 0.001µF B:CHIP IC2383 TC7W74FU LATCH 10 IC2381(3/3) MC74HC4053AFT SWITCH 16 4 5 14 12 13 IC2380(3/3) MC74HC4053AFT SWITCH 3 9 5 6 11 7 8 IC2381(1/3) MC74HC4053AFT SWITCH 4 3 C2389 0.01 F:CHIP 9 5 11-8 A B C D 11-8 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H B (3/4) B (3/4) 1 IC1401 CXA1739S RGB-MATRIX C1467 470 16V C1400 0.047 F:CHIP C1401 0.047 F:CHIP R1400 100 :CHIP R1447 100k :CHIP R1446 100k :CHIP C1429 0.1 25V F:CHIP C1402 0.047 50V B:CHIP C1428 0.1 25V B:CHIP C1427 0.1 25V F:CHIP R1402 10k :CHIP CN411 8P CN412 8P C1404 0.01 F:CHIP C1405 0.047 F:CHIP R1484 33k :CHIP R1483 47k :CHIP R1455 33k :CHIP Q1431 2SC2412K BUFFER R1437 3.9k :CHIP R1438 1k :CHIP C1426 0.1 25V F:CHIP R1405 C1406 100 :CHIP 0.047 25V B:CHIP R1406 100 :CHIP C1407 0.047 25V B:CHIP R1407 100 :CHIP C1408 0.047 25V B:CHIP R1426 100 :CHIP C1423 0.1 25V B:CHIP C1422 0.1 25V B:CHIP C1421 0.1 25V F:CHIP Q1434 2SC2412K CLAMP IC1300 MC74HC4053FEL SWITCH R1306 Q1302 1.2k 2SC2412K C1302 :RN-CP CLAMP 4p CH:CHIP R1307 100 :CHIP R1303 1k :RN-CP R1301 3.3k :RN-CP TP1300 R1300 100 :CHIP C1320 0.01 F:CHIP R1305 100 :CHIP R1302 1.8k :RN-CP IC1302 MC74HC4053FEL SWITCH Q1301 2SC3545 CLAMP R1321 3.3k :RN-CP C1322 8p CH:CHIP R1323 1k :RN-CP Q1320 2SA1462 CLAMP R1322 1.8k :RN-CP C1340 0.01 F:CHIP R1325 100 :CHIP R1341 3.3k :RN-CP IC1303 MC74HC4053FEL SWITCH C1342 3p CH:CHIP TP1302 R1340 100 :CHIP Q1340 2SA1462 CLAMP R1343 1k :RN-CP R1342 1.8k :RN-CP R1308 1k :CHIP R1319 4.7k :CHIP C1310 1/16V R1310 10k :RN-CP C1304 0.047 B:CHIP C1306 1 10V B:CHIP Q1305 2SA1037K BUFFER IC1305 TL082CPS CLAMP C1418 0.1 25V B:CHIP C1417 0.1 25V B:CHIP C1416 0.1 25V B:CHIP C1415 0.1 25V F:CHIP R1313 100 :CHIP R1408 1k :CHIP Q1303 2SC2412K BUFFER R1316 10k :RN-CP IC1304 MC74HC4053FEL SWITCH R1409 1k :CHIP R1416 100 :CHIP C1412 0.1 25V B:CHIP C1411 0.1 25V B:CHIP C1410 0.1 25V B:CHIP D1400 MA111 R1335 10k :CHIP Q1322 2SC2412K CLAMP R1327 100 :CHIP R1334 10k :CHIP IC1306 TL082CPS CLAMP C1326 0.01 F:CHIP IC1308 MC74HC4053FEL SWITCH IC1302 MC74HC4053FEL SWITCH C1330 1/16V IC1302 MC74HC4053FEL SWITCH Q1323 2SC2412K BUFFER R1333 0 :CHIP C1324 0.047 B:CHIP R1346 1.2k :RN-CP Q1342 2SC2412K CLAMP IC1306 TL082CPS CLAMP R1349 1M :RN-CP R1357 10k :CHIP C1346 0.01 F:CHIP IC1303 MC74HC4053FEL SWITCH C1344 0.047 B:CHIP R1348 1k :CHIP R1350 10k :RN-CP C Q1423 2SC3545 BUFFER R1430 82k :CHIP R1432 1k :CHIP R1435 4.7k :CHIP R1434 1k :CHIP Q1411 2SC2412K BUFFER Q1422 2SA1462 BUFFER R1419 10k :CHIP 3 Q1413 2SC3545 BUFFER R1420 82k :CHIP C1414 0.001µF CH:CHIP R1425 4.7k :CHIP R1454 33k :RN-CP R1423 470 :CHIP R1457 33k :CHIP Q1402 2SA1037K IK-BUFFER R1422 1k :CHIP Q1412 2SA1462 R1424 BUFFER 1k :CHIP Q1414 2SC2412K CLAMP R1415 470k :CHIP R1414 33k :CHIP Q1401 2SC2412K IK-BLK R1412 47k :CHIP R1480 6.8k :CHIP 4 R1481 4.7k :CHIP R1472 470k :RN-CP C1460 0.47 25V F:CHIP R1460 470k :CHIP R1450 10k :RN-CP C1468 47 16V :HT-CP Q1460 2SC2412K PIC ABL D1402 MA111 R1471 39k :RN-CP R1473 10k :CHIP Q1462 DTC144EKA SWITCH C1462 0.01 F:CHIP R1461 33k :CHIP R1451 47k :CHIP D1401 MA111 R1482 3.3k :CHIP R1464 39k :RN-CP C1461 0.01 F:CHIP C1464 0.47 25V F:CHIP R1352 2.2k :CHIP R1431 470 :CHIP C1413 100p CH:CHIP R1466 470k :CHIP IC1309 MC74HC4053FEL SWITCH Q1432 2SA1462 BUFFER R1413 33k :CHIP C1450 0.01 F:CHIP C1451 100p CH:CHIP R1351 100 :CHIP IC1307 TL082CPS CLAMP D R1417 3.9k :CHIP R1354 27k :RN-CP C1345 0.01 B:CHIP 2 R1442 1k :CHIP R1421 470 :CHIP R1418 1k :CHIP IC1400 MC74HC4538AFEL MONO MULTI Q1343 2SC2412K BUFFER R1353 0 :CHIP C1350 1/16V R1456 33k :CHIP Q1463 DTC114EKA SWITCH C1348 100p CH:CHIP IC1309 MC74HC4053FEL SWITCH Q1424 2SC2412K CLAMP R1433 470 :CHIP Q1400 DTC144EKA IK-MASK D1403 MA111 Q1421 2SC2412K R1429 10k BUFFER :CHIP C1420 0.001µF CH:CHIP R1453 33k :RN-CP R1355 47k :RN-CP C1347 0.01 F:CHIP Q1341 2SC3545 CLAMP R1332 2.2k :CHIP IC1308 MC74HC4053FEL SWITCH IC1309 MC74HC4053FEL SWITCH R1358 10k :CHIP IC1303 MC74HC4053FEL SWITCH C1409 0.22 16V R1411 B:CHIP 33k :CHIP C1431 100p R1330 10k :RN-CP IC1307 TL082CPS CLAMP R1401 0 :CHIP R1485 10k :CHIP D1404 RD10SB3 R1331 100 :CHIP C1325 0.01 B:CHIP C1327 0.01 F:CHIP Q1321 R1328 1k 2SC3545 :CHIP CLAMP R1347 100 :CHIP IC1308 MC74HC4053FEL SWITCH R1329 1M :RN-CP R1444 1k :CHIP C1419 100p CH:CHIP Q1410 2SA1462 BUFFER R1314 2.2k :CHIP R1317 39k :RN-CP 11-9 B C1309 2.2 16V F:CHIP C1308 0.01 F:CHIP R1318 4.7k :CHIP BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A IC1304 MC74HC4053FEL SWITCH R1315 0 :CHIP C1305 0.01 B:CHIP IC1305 TL082CPS CLAMP C1307 0.01 F:CHIP R1410 100 :CHIP C1343 R1344 # CH:CHIP # :RN-CP R1345 100 :CHIP C1341 0.01 F:CHIP R1311 10k :CHIP R1326 1.2k :RN-CP TP1301 R1320 100 :CHIP C1321 0.01 F:CHIP IC1300 MC74HC4053FEL SWITCH IC1300 MC74HC4053FEL SWITCH R1309 1M :RN-CP Q1304 2SC2412K BUFFER Q1300 2SA1462 CLAMP C1301 0.01 F:CHIP R1312 10k :CHIP IC1304 MC74HC4053FEL SWITCH Q1433 2SC3545 BUFFER R1445 4.7k :CHIP R1443 470 :CHIP R1428 1k :CHIP R1427 3.9k :CHIP R1441 470 :CHIP R1440 82k :CHIP C1425 0.001µF CH:CHIP Q1420 2SA1462 BUFFER C1300 0.01 F:CHIP C1424 100p CH:CHIP R1436 100 :CHIP Q1430 2SA1462 BUFFER R1452 33k :RN-CP R1439 10k :CHIP C1465 0.01 F:CHIP C1469 47 16V :HT-CP C1466 0.01 F:CHIP R1469 1.2k :RN-CP Q1461 2SC2412K BRT ABL R1470 10k :RN-CP 5 R1467 27k :CHIP 11-9 E F G H B (4/4) B (4/4) SCL SDA SAD2 SAD1 SAD0 SW3 SW2 1 VCC CXA1875AM (IC4300, 4301, 4302, 4350) 16 15 14 13 12 11 10 9 LEVEL CONVERTER R2303 270 :CHIP R2301 4.7k :CHIP Q2301 2SC3454 R2302 22 :CHIP Q2302 2SA1462 R2307 100 :CHIP R2310 1k :CHIP C2300 5p CH:CP TP2345 R2300 100 :CHIP LEVEL CONVERTER C2351 C2310 C2311 47 0.01 16V 0.01 F:CHIP :HT-CP F:CHIP R2314 33 :CHIP Q2303 2SA1462 R2305 470 :RN-CP R2304 560 :RN-CP 2 I C DECODER POWER ON RESET R2309 100 :CHIP Q2300 2SA1462 R2308 1.8k :CHIP OPEN COLLECTOR LEVEL CONVERTER LATCH C2361 47 C2362 C2352 16V 0.01 0.01 F:CHIP :HT-CP F:CHIP – + 2 LATCH LATCH LATCH LATCH LATCH DAC DAC DAC DAC DAC AMP AMP AMP AMP AMP VCC R2331 4.7k :CHIP 3 Q2332 2SA1462 4 TP2365 R2335 470 :RN-CP R2338 1.8k :CHIP 6 7 8 Z8622812PSC (IC3403) R2344 33 :CHIP R2339 100 :CHIP R2334 560 :RN-CP 5 GND 3 DAC0 2 DAC1 1 R2340 1k :CHIP C2330 9p CH:CHIP Q2331 2SC3545 Q2330 2SA1462 C2363 C2364 47 C2353 16V 0.01 0.01 F:CHIP :HT-CP F:CHIP DAC2 R2323 1.8k :CHIP R2337 100 :CHIP R2332 22 :CHIP R2330 100 :CHIP Q2318 2SA1642 R2320 470 :RN-CP R2333 270 :CHIP R2329 33 :CHIP DAC3 Q2316 2SC3545 R2319 560 :RN-CP TP2355 R2324 100 :CHIP DAC4 Q2315 2SA1462 C2315 7pF CH:CHIP REG R2325 1k :CHIP SW0 R2317 22 :CHIP R2315 100 :CHIP Q2317 2SA1642 R2322 100 :CHIP SW1 R2318 270 :CHIP R2316 4.7k :CHIP 14 15 VDD VDD (DIGITAL) (ANALOG) Q2333 2SA1462 SLICED DATA DATA SLICER NRESET DATA MOD XFR BUF DATA RECOVERY 11 12 CLAMP DATA CLK RECOVERY SLICE LEVEL DISPLAY RAM SYNC SLICER COMMAND PROCESSOR TIMING LOGIC COMP SYNC CHAR ROW AND LOCK VERTICAL CTR AND CONTROL DECODER CONTROL R R2380 100 :CHIP Q2381 2SC2412K BUFFER IC2380(1/3) MC74HC4053AFT SWITCH IC2380(2/3) MC74HC4053AFT SWITCH Q2380 2SC2412K BUFFER R2386 100 :CHIP C2383 0.01 F:CHIP R2390 2.2k :CHIP R2389 10k :CHIP IC2382(1/2) LM393PS-E20 SAMPLING Q2383 2SC2412K BUFFER R2383 2.2k :CHIP R2385 2.2k :CHIP LUM BOX PHOSE/ FREQ DET PFD 8 LOOP FILTER LOOP FIL 13 VCO VSS VSS (DIGITAL) (ANALOG) 9 10 16 1 5 6 7 4 3 17 18 R2391 10k :CHIP C2385 0.001µF B:CHIP IC2383 TC7W74FU LATCH R2387 2.2k :CHIP C2387 0.01 F:CHIP DOT CLK R2392 10k :CHIP IC2381(2/3) MC74HC4053AFT SWITCH C2384 0.001µF B:CHIP R2381 2.2k :CHIP R2393 2.2k :CHIP OUTPUT LOGIC B LNG/SCK R2382 100 :CHIP C2390 0.01 F:CHIP C2388 0.01 F:CHIP CT/SDA 4 R2388 10k :CHIP IC2382(2/2) LM393PS-E20 SAMPLING DONF/SEN R2384 100 :CHIP C2386 0.01 F:CHIP Q2382 2SC2412K BUFFER G HORIZONTAL COUNTER NSIN CN304 10P WHT :S-MICRO 2 DCLK IC2381(3/3) MC74HC4053AFT SWITCH IC2380(3/3) MC74HC4053AFT SWITCH 5 IC2381(1/3) MC74HC4053AFT SWITCH C2389 0.01 F:CHIP 11-10 A B C D 11-10 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H B CXA1211M (IC400, 401) Vcc IN 2 7 8 M24C02-MN6T (IC3404) CONT 2 OUT 2 6 IN 1 3 CONT 1 OUT 1 1 8 5 E0 E1 E2 VCA 1 2 B BOARD WAVEFORMS VCC VCA 2 1 B 4 7 2 3 6 WC 5 3 1 4 3 1 SCL 2 SDA 0.90Vp-p (H) 2 k BIT EEPROM 5 0.60Vp-p (H) 0.60Vp-p (H) 7 6 0.90Vp-p (H) 8 GND 4 VSS 0.55Vp-p (H) CXA1521M (IC306, 307, 308) 9 0.55Vp-p (H) 0 0.55Vp-p (H) !¡ 0.90Vp-p (H) !™ M62399FP-TE2 (IC4351, 4352) 2 8 Vcc REGULATOR CS0 CS1 CS2 VDD VCC A04 A03 A02 A01 VREFU2 19 17 16 15 14 13 12 11 20 7 GND 2 0.82Vp-p (H) DC CONT GCA 0.85Vp-p (H) 1.3Vp-p (H) 1.5Vp-p (H) CHIP SELECT GAIN-CONT DC-CONT 6 GND 5 OUT !£ I C BUS TRANCEAVER GAIN 3 CONT V EE 4 18 ADDRESS DECODER IN 1 8BIT UPPER DIGITS SEGMENT R-2R 8BIT UPPER DIGITS SEGMENT R-2R 8BIT UPPER DIGITS SEGMENT R-2R 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT LATCH 8BIT UPPER DIGITS SEGMENT R-2R 8BIT UPPER DIGITS SEGMENT R-2R 8BIT UPPER DIGITS SEGMENT R-2R 8BIT UPPER DIGITS SEGMENT R-2R 1.5Vp-p (H) !¶ !∞ 5.0Vp-p (H) !• !§ 1.6Vp-p (H) !ª 1.4Vp-p (H) @º 2 CXA1739S (IC1401) 8BIT UPPER DIGITS SEGMENT R-2R !¢ 48 HUE R-Y 1 b-Y 2 CLAMP HUE & COLOR PROCESS 47 COLOR SH CONT 6 SHP AMP 1 43 V CC 42 R V CC SH IN 8 41 R OUT 9 40 R GND 38 R C/O CLAMP VIDEO SW B IN 12 37 G VCC OSD R 13 36 G OUT OSD G 14 35 G GND YM 17 SHP AMP HP 20 AUTOMATIC CUTOFF CONTROL PROCESS 4.0Vp-p (V) @™ @£ 3 SCL SDA R 8 4 5 6 7 10 9 @¢ VREFL A05 A06 A07 A08 GND VREFU1 4.0Vp-p (H) MC74HC4538AFEL (IC1400) @∞ VDD 2-C 2-CR 2-RD 2-CK 2-CR 2-Q 2-Q 16 15 14 13 12 11 10 9 4.2Vp-p (V) @§ 0.90Vp-p (H) @ª 0.80Vp-p (H) @¶ 0.50Vp-p (H) #º 0.80Vp-p (H) @• 0.80Vp-p (H) #¡ 0.50Vp-p (H) #™ 4 32 G DRIVE 31 B V CC 1.1Vp-p (H) 30 B OUT PULSE GENERATOR GAMMA CONTROL 29 B GND MUTE 21 28 B S/H V BLK 22 27 B C/O CLP 2 23 26 B DRIVE CLP 1 24 25 IK #£ 1 2 3 4 5 6 7 8 1-C 1-CR 1-RD 1-CK 1-CK 1-Q 1-Q GND 0.5Vp-p (H) #¢ 0.65Vp-p (H) VCC PR CLR Q 8 7 6 5 S R Q C D Q 1 2 3 4 CK D Q GND TC7W74FU (IC2383) #¶ C #∞ 0.70Vp-p (H) #• 2.1Vp-p (H) 11-11 B 0.5Vp-p (H) 1.4Vp-p (H) #§ 2.4Vp-p (H) #ª 2.2Vp-p (H) $º 5 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A 1.8Vp-p (H) 33 G C/O PIC VP 18 GND 2 19 3 34 G S/H OSD B 15 YS 16 2 39 R S/H R IN 10 G IN 11 4.0Vp-p (H) 44 R DRIVE MATRIX AXIS SW BRIGHT 7 AXIS @¡ 45 GAMMA GND 1 4 SH OUT 5 4.2Vp-p (V) 46 PIC Y 3 D 4Vp-p (H) 3.4Vp-p (H) 3.0Vp-p (H) 11-11 E F G H B1 1 C502 0.01 F:CHIP IC501(1/3) MC74HC4053FEL R502 2.2k :CHIP R505 100 :CHIP Q515 2SC2412K 14 13 R541 2.2k :CHIP R504 1k :CHIP Q501 2SA1037K R546 2.2k :CHIP 12 R503 1k :CHIP Q502 2SC3545 16 DL501 R501 100 :CHIP R545 2.2k :CHIP R544 6.8k :CHIP R543 3.3k :CHIP B1 6 11 7 R506 100 :CHIP Q517 2SA1462 R547 100 :CHIP Q518 2SC3545 R548 1.2k :CHIP 8 B1 BOARD R507 2.2k :CHIP C503 0.01 F:CHIP R509 330 :CHIP R512 100 :CHIP DL502 R508 100 :CHIP R510 150 :CHIP Q516 2SC3545 R542 2.2k :CHIP R511 150 :CHIP Q503 2SA1462 2 R514 2.2k :CHIP DL503 R513 100 :CHIP R515 1k :RN-CP R520 100 :CHIP R537 100 :CHIP 9 Q514 2SC3545 R538 1.2k :CHIP R524 100 :CHIP R519 2.2k :CHIP Q512 2SC3545 DL504 R522 150 :RN-CP Q505 2SC3545 R536 2.2k :CHIP Q513 2SA1462 R531 2.2k :CHIP R521 330 :CHIP R535 2.2k :CHIP R534 6.8k :CHIP R518 100 :CHIP 4 5 3 Q511 2SC2412K R516 1k :RN-CP Q504 2SA1037AK R533 3.3k :CHIP IC501(3/3) MC74HC4053FEL R517 100 :CHIP 15 2 B1 –A SIDE– B1 –B SIDE– SUFFIX: -11 SUFFIX: -11 1 10 R532 2.2k :CHIP R523 150 :RN-CP Q506 2SA1462 IC501(2/3) MC74HC4053FEL 3 Q400 2SC2412K R400 100 :CHIP Q401 2SC2412K 14 13 DL400 R417 2.2k :CHIP DL401 R404 2.2k :CHIP C401 47 16V :HF-CP C403 0.01 F:CHIP 16 12 R405 1k :RN-CP R402 1k :RN-CP R401 2.2k :CHIP Q413 2SC2412K R406 100 :CHIP R403 100 :CHIP IC410(1/3) MC74HC4053FEL 6 11 7 CXA1211M (IC450) C402 47 16V :HF-CP Vcc C404 0.01 F:CHIP 8 8 IN 2 7 CONT 2 OUT 2 6 5 VCA 2 R410 100 :CHIP Q403 2SC2412K Q402 2SC2412K R412 470 :RN-CP R414 2.2k :CHIP DL402 R411 2.2k :CHIP 4 R418 2.2k :CHIP DL403 R422 100 :CHIP R432 3.3k :CHIP R427 1k :RN-CP R437 2.2k :CHIP R434 4.7k :CHIP 2 3 CONT 1 OUT 1 4 GND CN402 8P :B-TO-B R436 4.7k :CHIP Q407 2SA1462 R442 C407 0.1 100 25V :CHIP F:CHIP Q409 2SC3545 R438 10k :CHIP 4 5 IN 1 R419 33k :CHIP R439 2.2k :CHIP Q406 2SA1462 1 C412 0.01 F:CHIP R433 12k :CHIP IC410(3/3) MC74HC4053FEL VCA 1 Q410 DTC144EK IC450 CXA1211M C411 0.1 F:CHIP Q411 2SC2412K R421 1k :RN-CP R409 47k :CHIP R444 100 :CHIP R428 2.2k :CHIP R420 100 :CHIP R443 C410 100 0.1 :CHIP F:CHIP Q414 2SC3545 R415 470 :RN-CP R413 100 :CHIP CN401 8P :B-TP-B R416 100 :CHIP DL404 Q404 2SA1037 3 R407 2.2k :CHIP R431 100 :CHIP R430 100 :CHIP 9 Q408 2SC3545 R435 1.2k :CHIP R441 0 :CHIP R440 1k :CHIP R429 2.2k :CHIP IC410(2/3) MC74HC4053FEL DL405 R423 100 :CHIP 5 R424 470 :RN-CP Q405 2SA1462 Q412 2SC3545 R426 100 :CHIP 15 2 1 R425 470 :RN-CP 10 R408 2.2k :CHIP 11-12 A B C D 11-12 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H B2 B2 R3937 100 :CHIP IC3908 TC4W53F 1 C3924 0.01 F:CHIP C3901 0.01 F:CHIP R3915 9.1k :RN-CP Q3902 DTA144EKA Q3901 DTA144EKA R3932 R3930 1.2k 10k :RN-CP :RN-CP R3924 18k :RN-CP R3922 39k :RN-CP Q3906 DTA144EKA 6 8 7 Q3909 2SA1037K 5 4 R3907 120k :RN-CP R3905 120k :RN-CP R3913 1.5k :RN-CP R3910 100k :RN-CP C3910 0.01 F:CHIP R3925 82k :RN-CP R3918 1k :CHIP C3907 470p CH:CHIP R3927 100k :RN-CP C3912 270p CH:CHIP 16 1 15 IC3902(2/3) TC74HC4053AFT 2 7 11 8 6 R3934 100 :CHIP 12 9 4 1 Q3912 2SC3326N 7 8 10 3 R3935 1k :CHIP 3 IC3907 TC7S02F R3908 2.7k :CHIP C3906 100p CH:CHIP R3904 100 :CHIP IC3902(3/3) TC74HC4053AFT C3919 0.01 F:CHIP D3902 1SS352 Q3910 2SA1037K 2 C3921 0.22 16V B:CHIP IC3904(2/2) TC74HC4538AF-TP2 IC3906 TC750F R3929 18k :RN-CP D3904 1SS352 R3939 100k :CHIP 5 15 2 13 CN3902 12P BOTB D3903 R3936 1SS352 100k :CHIP 19 13 9 C3920 0.01 F:CHIP 1 2 12 R3901 100 :CHIP 14 11 R3916 100 :CHIP 4 10 R3933 1k :RN-CP 10 6 5 14 C3915 220p CH:CHIP IC3904(1/2) TC74HC4538AF-TP2 IC3901(2/2) TC74HC4538AF-TP2 15 IC3905(1/2) NJM4558M-TE2 C3913 0.01 F:CHIP C3903 470p CH:CHIP IC3901(1/2) TC74HC4538AF-TP2 C3923 0.01 F:CHIP C3917 0.01 F:CHIP Q3913 2SC3326N R3938 10k :CHIP Q3911 DTC144EKA C3922 0.22 16V B:CHIP R3940 10k :CHIP C3909 220p CH:CHIP R3920 1k :CHIP 5 4 3 Q3903 2SA1037K 9 C3918 0.01 F:CHIP R3912 2.2k :CHIP C3904 0.0047µH B:CHIP R3903 3.9k :RN-CP R3906 2.2k :RN-CP C3902 0.0022µH B:CHIP R3909 2.2k :RN-CP C3905 0.001µH B:CHIP R3919 4.7k :CHIP C3908 1 16V F:CHIP R3914 100 D3901 :CHIP 1SS352 R3926 C3914 1k 0.01 :CHIP F:CHIP R3928 100 :CHIP R3948 0 :CHIP Q3905 2SA1037K IC3902(1/3) TC74HC4053AFT 3 1 R3931 1k :CHIP 2 16 12 3 14 IC3905(2/2 NJM4558M-T E 13 6 11 7 R3917 100k :CHIP 8 C3916 0.01 F:CHIP Q3907 2SC2412K R3923 100 :CHIP Q3908 2SA1037K R3902 100 :CHIP 4 B2 BOARD TC4W53FU (IC3908) COMMON 1 INH 2 OUT IN C 8 VDD 7 CH0 6 CH1 5 A LOGIC LEVEL CONVERTOR VEE 3 OUT IN C VSS B2 –A SIDE– B2 –B SIDE– SUFFIX: -11 SUFFIX: -11 11-13 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 4 5 11-13 E F G H C 1 C C BOARD R788 68k 1/2W :RC J701 SG701 R787 7.5JW CN701 8P :VH L701 R708 39µH 270k 1/2W :RC C702 680p 2kV B RV701 110M C704 0.0047 2kV RV702 2.2M 2 C703 0.022 1kV :PP R707 100k 1/2W :RC TP701 TP702 L730 3.3µH :EL0606 Q701 2SD982 R701 1.5 1/4W :FPRD R702 8.2k 1/4W :FPRD Q733 2SC3503-E R765 220 1/2W :RC C754 C755 33 0.01 250V 500V :HT E D736 MA111-TX R740 5MM R754 2.7k 10W :RN D753 MA111-TX R739 33 1/10W :CHIP D735 MA111-TX C733 0.01 50V F:CHIP CN702 10P WHT-L :S-MICRO D732 MA111-TX D731 MA111-TX D734 MA111-TX Q735 2SA1330 R738 33 1/10W :CHIP R735 47 1/10W :CHIP C753 0.01 50V F:CHIP R741 39k 1/10W :CHIP D752 MA111-TX D738 RD22M-T1B3 D773 MA111-TX D754 MA111-TX R742 33k 1/10W :CHIP SUFFIX: -11 4 R732 150 1/2W :RN R703 47 1/10W :CHIP C –B SIDE– R733 22 1/4W :RN R704 100 :CHIP C730 220p B R705 10k 1/10W :CHIP R758 33 1/10W :CHIP R761 39k 1/10W :CHIP C773 0.01 50V F:CHIP D772 MA111-TX D771 MA111-TX Q771 2SC3503-E Q752 2SA1381-E D774 MA111-TX R775 47 1/10W :CHIP R743 33k 1/10W :CHIP R744 220 1/10W :CHIP C771 C772 47 0.01 25V 50V :HT F:CHIP R762 33k 1/10W :CHIP Q750 2SC3950-E R751 100 1/10W :CHIP R752 150 1/2W :RN C750 220p :CH Q775 2SA1330 R778 33 1/10W :CHIP R781 39k 1/10W :CHIP D778 RD22M-T1B3 Q772 2SA1381-E D770 MA111-TX R764 220 1/10W :CHIP C777 22p R782 33k 1/10W :CHIP R783 33k 1/10W :CHIP Q770 2SC3950-E D757 MA111-TX R763 33k 1/10W :CHIP R753 22 1/4W :RN R779 33 1/10W :CHIP R777 1k 2W :RS D750 MA111-TX D737 MA111-TX D776 MA111-TX R780 5MM Q774 2SK520 R776 47 1/10W :CHIP R757 1k 2W :RS C751 C752 47 0.01 25V 50V :HT F:CHIP R731 100 1/10W :CHIP Q773 2SC3503-E D775 MA111-TX Q755 2SA1330 R755 47 1/10W :CHIP R737 1k 2W :RS D730 MA111-TX Q730 2SC3950-E R759 33 1/10W :CHIP D758 RD22M-T1B3 Q751 2SC3503-E Q732 2SA1381-E C732 0.01 50V F:CHIP R774 2.7k 10W :RN R756 47 1/10W :CHIP D755 MA111-TX D751 MA111-TX Q731 2SC3503-E C731 47 25V :HT R785 220 1/2W :RC Q754 2SK520 R736 47 1/10W :CHIP R786 2.2k 1/2W :RC L770 3.3µH :EL0606 C774 C775 33 0.01 250V 500V :HT E D756 MA111-TX Q753 2SC3503-E Q734 2SK520 D733 MA111-TX SG705 R766 2.2k 1/2W :RC L750 SG704 3.3µH :EL0606 SG703 R745 220 1/2W :RC C701 33 250V :HT CN703 3 R746 2.2k 1/2W :RC C734 C735 33 0.01 250V 500V :HT E R734 2.7k 10W :RN TP703 TP700 SG702 R771 100 1/10W :CHIP R772 150 1/2W :RN R773 22 1/4W :RN C770 220p B D777 MA111-TX R784 220 1/10W :CHIP C778 33p :CH Q702 2SC1654 R706 4.7k 1/10W :CHIP C BOARD WAVEFORMS 1 2 0.1Vp-p (H) 0.1Vp-p (H) 5 5 3 0.1Vp-p (H) 6 61Vp-p (H) 4 56Vp-p (H) 7 55Vp-p (H) 54Vp-p (H) 11-14 A B C D 11-14 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H G G G BOARD A B C D E F G H J K 1 [G BOARD] * : B-SIDE D2501 D2502 D2503 D2504 D2506 D2507 D2508 D2509 D2510 D2511 D2512 D2513 D2514 D2515 D2520 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D515 D516 D517 D518 D519 D520 D524 D525 D529 D530 D531 D532 D533 D534 D535 D536 D537 D538 D539 D540 D601 D602 D603 D604 D605 D607 D608 D609 D612 D614 D617 D619 D620 D622 D623 D624 D625 D626 D627 D633 D634 D635 D636 D637 D638 D639 D640 F-6 G-7 F-6 J-5 G-7 H-6 E-7 E-7 H-7 H-7 J-6 K-5 H-5 * E-6 * J-5 * E-2 * E-2 * E-2 * E-2 E-2 * J-3 * J-2 * J-2 * J-2 * J-2 * J-2 * J-2 J-3 * K-4 * F-1 H-4 * F-2 J-4 J-4 H-3 G-2 * G-3 * C-1 E-1 * C-2 * C-2 * B-2 * D-1 * F-2 * C-1 * F-2 * C-1 * C-2 * B-1 * B-3 B-4 * C-3 C-3 C-4 * C-4 D-7 * D-4 * C-4 * D-5 * D-5 * D-4 * D-4 F-5 F-5 G-4 D-3 F-4 F-2 * C-3 A-2 C-6 * D-5 F-4 * E-2 * F-2 * F-2 IC2501 IC2502 IC2503 IC2504 IC501 IC502 IC503 * F-6 * E-6 K-5 E-6 B-1 D-1 B-1 1 IC506 IC507 IC508 IC509 IC510 IC512 IC514 IC515 IC516 IC517 IC519 IC520 IC522 IC523 IC524 IC526 IC527 IC528 IC529 IC601 IC602 IC606 IC607 IC608 IC609 IC610 B-1 C-1 C-2 B-2 E-1 E-1 K-2 E-1 D-1 K-1 F-2 * G-2 B-1 * J-2 B-2 B-1 B-2 D-1 A-2 D-7 C-5 F-3 F-3 D-3 E-2 D-3 Q2501 Q2502 Q2503 Q2504 Q2505 Q2508 Q2511 Q2513 Q2514 Q2515 Q2518 Q2519 Q501 Q504 Q505 Q506 Q507 Q508 Q509 Q510 Q511 Q512 Q513 Q514 Q517 Q518 Q520 Q521 Q523 Q524 Q525 Q529 Q530 Q531 Q532 Q533 Q534 Q535 Q536 Q601 Q602 Q603 Q604 Q605 Q608 Q609 Q611 Q612 Q613 Q614 Q615 Q616 Q617 Q618 Q619 Q620 Q621 Q622 G-6 G-6 G-7 E-6 G-6 J-7 J-5 J-5 G-5 * G-5 G-5 * G-5 B-1 E-2 * F-1 * J-4 * K-4 * F-1 * F-1 F-1 F-1 F-1 K-4 H-4 G-3 G-3 * C-1 * D-2 E-2 * C-1 * D-1 B-2 B-2 B-2 * E-1 * F-2 * E-1 * C-1 B-2 * A-2 C-4 * C-3 * C-3 D-4 D-4 * D-4 * F-2 * F-2 * F-2 G-4 * D-3 * F-2 * F-2 * D-2 * A-2 * F-2 * F-2 * E-2 2 2 3 3 4 5 4 6 5 7 G –A SIDE– SUFFIX: -11 11-15 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-15 E F G H G K J H G F E G D C B A 1 1 2 2 3 3 4 5 4 6 5 7 G –B SIDE– SUFFIX: -11 11-16 A B C D 11-16 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H G (1/3) G (1/3) 1 C685 0.001 500V B Q619 DTA144EKA C603 0.1 25V B:CHIP R601 10k :CHIP D601 MA111 D626 FB603 5MMJW D1NL40-TA D623 D4SBL20U Q601 2SC2412K T603 PFC R603 33 1/2W T605 IC602 MCR5102 FB602 5MMJW R644 0.1 1/2W :RF R615 470k :RN CN601 3P WHT :MINI L609 1.1µH D602 D4SB60L C606 0.0047 250V R679 4.7M 1/2W :RC R680 4.7M 1/2W :RC CN602 7P L601 68µH C607 0.0047 250V RY602 R613 0.33 2W :RB R619 1.8k :RN-CP D612 SC802-04 R620 10k :RN-CP C617 10 :HT C616 0.01 B:CHIP C614 47 :HT C615 330 450V R602 330k 1/2W :RC C602 1000pF 250V E C608 1000pF 250V E R631 1k :RN-CP C604 1 250V D605 RD12ESB2 D606 1SS119 R604 150 R609 2W 4.7k :RS :CHIP T602 LFT D603 RD30SB C610 100 :HT Q605 DTA143ESA R626 1M 1/2W R607 82k :CHIP R605 100k :CHIP PH603 PC123FY2 D620 MA111 2 L617 47µ CN606 8P WHT :S-MICRO C664 47 25V :HT C665 C690 47 470 25V 10V :HT L614 C689 IC609 47µ 470 LM2990 10V IC608 BA05T D622 S2L20UF R678 10k :CHIP C667 0.01 B:CHIP R651 100k :CHIP C653 10 :HT R657 470 :CHIP D634 RD6.2ESB C636 2200 25V :HT Q618 DTC144EKA C669 0.01 B:CHIP D640 RD3.3SB1 Q615 2SC2412K PH604 PC123FY2 R624 47 :FPRD CN605 6P RED :S-MICRO L615 47µ L616 47µ IC610 SE135 R654 1k :CHIP C671 0.01 B:CHIP Q616 DTC114GKA 3 D633 MA111 R638 22k :CHIP C666 10 :HT R669 1k :CHIP L613 47µ Q609 DTC114EKA D604 RGP02-17 R668 Q614 470k R664 2SA1091 150k :RN IC607 NJM7912FA R672 0.1 1/2W :RF R610 1k :CHIP CN603 3P WHT :VH C682 0.001 B:CHIP D609 MA111 C612 10 :HT F601 4A 250V R667 10k :CHIP C662 47 25V :HT C663 47 25V :HT C651 1000 25V :HT C652 1000 25V :HT C643 2200 25V :HT C644 2200 25V :HT CN604 8P :VH Q617 DTA114GKA D617 RD12SB1 R641 470 :CHIP Q604 DTA114GKA D630 MA111 IC606 BA12T C649 1000 25V :HT C650 1000 25V :HT L608 47µH Q603 2SC2412K R612 47k :CHIP C661 10 :HT Q613 DTA114EKA R662 390k Q611 :RN DTC114GKA R665 10k :RN-CP R658 150k :CHIP L606 22µH D636 SC311-06 C623 D614 0.1 SC311-06 100V :PT R677 47k :CHIP D607 MA111 C680 0.001 B:CHIP R642 0.1 1/2W :RF D619 MA111 R661 1.2k :RN-CP C681 0.001 B:CHIP L607 47µH C679 0.001 B:CHIP R683 0.1 1/2W C641 2200 25V :HT C642 2200 25V :HT D625 D4SBS4 C627 100µF :HT R623 1M 1/2W C670 22 :HT R643 0.1 1/2W :RF C678 0.001 B:CHIP :RF R621 0.33 2W :RS C609 0.01 B:CHIP R645 L610 C676 0.1 0.001 1/2W 1.1µH B:CHIP :RF Q608 DTA143ESA R622 0.33 2W :RS R608 10k :CHIP R682 0.1 1/2W :RF C625 10 :HT VDR602 Q602 2SC3311A C675 0.001 B:CHIP C631 0.0047 1kV :PP R636 1M 1/2W D627 RD18ESB1 R666 0.56 3W :RS R659 1k :CHIP C638 220 100V C654 :HR 10 C677 L605 :HT 0.001 B:CHIP 22µH D624 D4SBS4 R635 1M 1/2W C621 4.7 :HT R618 12k :RN-CP D608 RD27ESB2 C674 100p CH C613 0.68 :MPS C611 R611 1 400V 0.33 2W :RB R606 6.8 10W :RB C624 8200pF :PP R616 470k :RN R617 470k :RN IC601 MZ1540 C648 22 250V :HT Q612 DTA114GKA R652 330k :RN R653 C637 47k 220 :RN-CP 100V :HR VDR601 RY601 L604 22µH L603 22µH C645 4.7 200V :HT FB606 1.1UH C629 0.0047 1kV :PP D637 DIN20R C683 0.001 500V B R627 0.1 1/2W :RF R614 10k :CHIP D635 RM11A THP601 C640 220 :HT C684 0.001 500V B D639 MA111 R685 22k :CHIP R686 4.7k :CHIP R684 22k :CHIP D638 RD7.5SB1 C687 100 10V R628 47 :FPRD CN608 3P WHT :VH Q621 DTC114EKA Q620 DTC144EKA Q622 DTC144EKA 4 C688 0.01 CN607 5P WHT :VH 5 11-17 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-17 E F G H G (2/3) G (2/3) 1 D505 RD12SB1 R528 10k :CHIP R523 10k :CHIP L502 47µ 12V C507 220 R522 10k 25V :HT :CHIP 12V Q504 DTA114EKA C537 0.1 25V F:CHIP R545 27k :RN-CP C534 22 16V C1508 0.47 16V R543 B:CHIP 33k :CHIP R546 8.2k :RN-CP R540 D502 12k :CHIP MA111 Q523 DTC144EK R514 10k :CHIP 2 R544 15k :CHIP R547 10k :CHIP R525 15k :CHIP C538 0.0015 IC507 TDA9106 15V C1541 4.7 50V C519 0.01 B:CHIP C504 0.01 F:CHIP C505 0.01 :PPS-CP R501 1k :RN-CP C514 0.0047 B:CHIP C508 C509 0.0047 B:CHIP 0.001 CH:CHIP CN501 12P WHT :S-MICRO R506 22k :CHIP R1568 C1523 47k 0.47 :CHIP B:CHIP C525 0.22 B:CHIP C526 0.47 B:CHIP C1524 0.47 B:CHIP R1576 100 :RN-CP R551 1k :CHIP R1586 10k :RN-CP Q535 2SC2412K D535 MA111 R1546 0.47 1/4W :FPRD C563 C561 0.022 220p 25V B:CHIP B:CHIP C568 0.047 200V C569 330p R573 220k :CHIP Q506 2SC3392 R588 100 1/4W :FPRD IC524 MC74HC175FEL C594 0.01 F:CHIP Q507 2SA1338 R531 220k :CHIP L503 10µ 4 R1573 1M :CHIP C1534 0.01 B:CHIP C1533 0.01 B:CHIP IC510 TC74HC4538AF Q534 DTA144EKA R1534 56k :RN-CP IC528 TC7W00F R1580 27k :RN-CP C531 0.068 B:CHIP C1505 0.022 :PPS-CP C1520 0.001 CH:CHIP IC529 TC74HC4538 R1581 3.3k :CHIP R1582 10k :CHIP C1535 0.1 25V B:CHIP -5V CN502 7P WHT :S-MICRO C598 1000 10V :HT C596 C592 0.01 0.01 F:CHIP F:CHIP C588 0.01 F:CHIP Q501 IMT2 R505 33k :CHIP IC506 TL082CPS R510 12k RN:CHIP C510 2.2 16V F:CHIP R511 6.8k :CHIP C591 0.01 F:CHIP IC506 TL082CPS 5 C1519 0.01 F:CHIP D534 MA111 C516 0.47 IC509 TC74HC4538AF C520 0.001 B:CHIP C595 470 10V :HT R1533 8.2k :RN-CP C1526 0.001 B:CHIP R1561 68k :RN-CP R1532 15k :RN-CP C1518 0.01 F:CHIP R517 10k :CHIP C1512 0.01 F:CHIP IC501 TS082CPS C1527 R1548 10p 1k CH:CHIP :CHIP R1552 47k :CHIP C1513 0.01 F:CHIP R1549 33k :RN-CP R1550 33k :RN-CP R1547 4.7k :RN-CP IC501 TS082CPS C554 1 C551 0.01 B:CHIP R595 6.8k :CHIP R574 6.8k :CHIP R589 2M 1W :RN Q508 2SC1037AK R584 1.5k :CHIP R570 1.2k :CHIP D515 MA111 R1525 10k :CHIP NL501 R1505 22 :FPRD R1508 22 :FPRD Q509 2SC2412K C562 1 16V B C552 10 R1541 10k :CHIP R1507 47 :FPRD T501 DFT R590 270 :CHIP Q512 2SB734 C1539 10 R1569 5.6k :RN-CP R586 10k R562 470 :RN-CP D512 MA111 Q536 DTA144EKA R1589 100k :RN-CP 11-18 D C556 0.01 B:CHIP R1526 10k :CHIP D532 D531 MA111 MA111 R1545 C1525 470k 0.01 :CHIP B:CHIP R576 C559 3.3k 0.01 B:CHIP :RN-CP R578 10k :RN-CP C574 1 16V B R1516 R1521 4.7k 4.7k :RN-CP :RN-CP R579 10k :RN-CP R1517 4.7k :RN-CP IC517 µPC1093J R580 3.3k :RN-CP IC526 TC4530F CN503 3P WHT :S-MICRO Q511 2SD774 C566 10p SL:CHIP R585 100k :CHIP 12V D511 MA111 C599 0.01 F:CHIP R1524 10k 1/2W Q517 :RC 2SC4686 Q510 2SD774 15V Q505 2SC1037AK C555 R566 1k 0.1 25V :CHIP F:CHIP IC523 LM393PS R1519 2M 1W :RN Q518 2SC4686 C587 1 16V B D528 R1515 68k :CHIP MA111 R1520 10M 1W :RN C576 1.5 200V IC522 TC4530F R1588 47k :RN-CP C R1514 10k :CHIP R1502 100 3W :RS R569 C564 22k 0.01 :RN-CP F:CHIP C558 10 R564 1k :CHIP R559 10k :CHIP C593 0.01 F:CHIP C1503 470p CH:CHIP -5V B IC514 µPC1093J C1511 0.1 25V B:CHIP R1585 R1590 56k 100k :RN-CP :RN-CP D533 R1551 1k MA111 :CHIP IC527 TC4S11F IC520 LM358 D525 MA111 R561 10k :RN-CP D507 MA111 C1538 0.001 B:CHIP R1555 2.2k :CHIP C1515 10p CH:CHIP R560 10k :RN-CP C1537 R1557 0.01 100k C1516 B:CHIP :RN-CP 0.1 25V B:CHIP IC502 TL082CPS R597 10 1/4W :FPRD D513 RGP10G R575 91k :RN-CP C557 0.01 B:CHIP R1556 10k :RN-CP R1560 56k :RN-CP R1553 4.7k R1554 :CHIP 1k :CHIP R553 470 :RN-CP R1558 1M :RN-CP IC502 TL082CPS R1587 33k :RN-CP A R1584 15k :RN-CP C1517 0.01 R1559 F:CHIP 1k :CHIP R1562 1k :CHIP R1583 100k :CHIP C1514 0.01 F:CHIP D509 MA111 C550 0.01 B:CHIP IC523 LM393PS C553 0.01 B:CHIP -5V 5V C528 0.01 F:CHIP C578 0.0047 2kV D524 RD12ESB2 C577 0.0047 200V R1563 47k :CHIP C1536 0.001 B:CHIP D514 MA111 IC516 MC14053BF R549 4.7k :CHIP R1535 120k :RN-CP C1528 470 6.3V :HT IC520 LM358 C582 0.01 B:CHIP D506 MA111 R1579 56k :RN-CP D520 RGP02 Q521 2SC2412K 12V R1578 68k :CHIP T503 HRT R1506 1k T502 FBT R550 100 :CHIP C1507 0.01 B:CHIP D519 FE3DL-6488 Q513 2SK2655 R526 470 :CHIP R527 1k :CHIP D518 FE3DL-6488 FB502 1.1UH C573 0.0017 1.6kV :PP R596 10 :CHIP Q530 DTC144EKA R1570 33k :CHIP Q514 IRFI9630GS C570 33 160V C575 330p 500V B R1512 22k :CHIP C565 0.1 R594 25V 10k B:CHIP:CHIP Q531 DTC144EKA Q529 DTC144EKA D516 RD9.1ESB2 FB501 1.1UH C571 680p 2kV R521 2.7k :CHIP R1571 100k :CHIP R518 10k :CHIP R1577 5.1k :RN-CP R592 1k :CHIP C524 C527 0.01 100 B:CHIP Q525 DTA144EKA D538 RD13SB2 Q520 DTC114EK R520 15k :CHIP R529 470 :CHIP R1509 10k :RN-CP Q533 2SA1037K D517 RD12SB1 R509 10k :CHIP R1567 100k :CHIP D541 RD6.8ESB2 IC519 µPC1093J R567 27k :CHIP C560 1 R1544 10k Q524 :CHIP DTC144EKA R548 1k :CHIP R512 10k :CHIP C1540 10/50V C1530 470p B:CHIP C1531 C530 470p B:CHIP 100 10kR503 :CHIP R1575 5.6k :CHIP R582 22k :RN-CP R572 2.2k :CHIP C547 R556 0.0022 10 :CHIP B:CHIP D530 MA111 C1532 47 16V R1566 22k :CHIP C513 100 D539 RD13SB2 Q532 DTA144EKA D529 MA111 D536 MA111 C1506 0.01 B:CHIP R519 9.1k C511 :RN-CP 0.01 B:CHIP C521 0.22 C522 F:CHIP 1 16V F:CHIP C512 10 R508 680 C523 :CHIP 820p C515 CH:CHIP 0.01 R513 B:CHIP 1k :CHIP L501 100µ R1574 10k :CHIP C529 0.01 B:CHIP C518 47 R502 22k :RN-CP 3 D540 RD6.8ESB2 C517 0.022 B:CHIP D537 RD10SB1 R581 R593 27k 22k :RN-CP :CHIP C539 R552 0.015 47k 25V :CHIP B:CHIP R504 10k :CHIP R515 10 :CHIP C549 10 R542 D503 100 :CHIP MA111 R507 10k :CHIP C501 0.001 CH:CHIP R591 10k :CHIP C585 100 C581 0.01 B:CHIP R555 100 :CHIP R524 100 :CHIP D501 MA111 C502 100p CH:CHIP R571 10k :CHIP D504 RD15SB1 IC512 CXA1875AM IC503 TC74HC4538AF R599 R577 4.7k 4.7k :CHIP :CHIP TH501 3K R583 3.9k :CHIP C536 47 IC508 CXA1875AM C503 220 25V :HT R565 22 :CHIP C548 IC515 CXA1544M 47 R554 22 :CHIP C546 0.01 F:CHIP C567 0.01 B:CHIP R1518 8.2k :RN-CP C1521 0.047 25V B:CHIP C1500 0.01 F:CHIP C1522 1 16V B:CHIP C589 0.01 200V :PT R1522 4.7k :RN-CP R1523 5.6k :RN-CP 11-18 C590 0.01 200V :PT BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H G (3/3) G (3/3) G BOARD WAVEFORMS 1 4.0Vp-p (H) 4.0Vp-p (V) 4 3 4.7Vp-p (H) IC2503 TDA8172 1 2 5 4.9Vp-p (H) 6 R2524 10k :CHIP R2509 10k :CHIP R2502 1.5 1/4W :FPRD D2520 RD6.8SB R2570 15k :CHIP C2507 0.01 B:CHIP R2504 C2509 0.01 1.5 1/4W B:CHIP :FPRD 4.9Vp-p (V) C2516 0.1 100V :PT D2504 GP08D R2514 4.7k :CHIP C2510 1000 2 R2522 C2519 4.7k 0.022 :CHIP B:CHIP C2513 100 7 R2518 R2520 1.5 270 2W :RS C2511 1000 R2521 2.2 2W :RS R2571 4.7k :CHIP Q2503 IRFI9630 FB2501 1.1UH R2523 2.2 2W :RS T2501 HOT FB2503 1.1UH R2528 0.47 1/2W :FPRD C2512 D2502 330p RD9.1ESB2 C2506 0.047 200V :PT 6 5 C2505 0.01 B:CHIP R2503 10k :RN-CP C2504 0.1 25V B:CHIP IC2504 LA6500 D2508 FE3DL-6488 R2510 2.7k :CHIP R2506 22 1/2W :FPRD C2503 100 C2537 0.047 B:CHIP R2527 0.47 1/2W :FPRD D2509 FE3DL-6488 R2531 22k :CHIP 1 Q2504 2SC2362KG IC2502(1/2) NJM4558M R2519 10k :CHIP R2574 33 3W :RS R2546 10k :CHIP R2560 C2538 0.1 10 :FPRD B:CHIP Q2511 2SA1221 R2547 39 2W :RS L2502 470µH :EL0606 9 T2503 0 L2504 HLC R2557 150 3W :RS R2551 68 1W :RS Q2512 DTC144EKA R2564 1 2W :RS 8 4 L2503 HLC R2562 D2515 R2563 22k 2.2k :CHIP RD5.6SB2 :CHIP C2523 1000 16V D2512 1SS119 5.0Vp-p (V) C2534 R2554 0.01 100 B:CHIP 2W :RS R2545 10k :CHIP R2561 1.5k :CHIP IC2502(2/2) NJM4558M 3 2 C2524 1000 16V 4.8Vp-p (H) R2548 10k :CHIP R2550 100k :CHIP L2501 HCC R2559 4.7k :CHIP D2506 ERD38-06 7 8 CN2501 6P WHT :VH Q2513 2SA1309A R2505 0.47 1/4W C2508 33 :FPRD 160V 1.5Vp-p (H) D2513 GP08D C2532 0.68 250V :PP C2529 22 250V :HT C2533 0.82 250V :PP C2539 1 16V F:CHIP 2.8Vp-p (V) !¡ RY2501 C2544 0.001 2kV C2541 1 250V :HT L2505 2.2mH :EL0606 R2552 100k :CHIP !™ C2536 3.3 250V :PP C2543 3.3 250V :PP 4.9Vp-p (V) R2572 10 3W :RS !£ 4.9Vp-p (H) !¢ Q2514 2SK2350 Q2518 2SK2350 L2507 1mH 1.2Vp-p (H) C2501 0.01 B:CHIP D2503 RD5.6SB2 C2502 100p 2kV B R2501 330 :CHIP D2501 RD5.6SB2 R2512 10k :CHIP R2513 6.8k :CHIP IC2501 TC4S71F C2514 100p 2kV C2515 0.0015 630V :PP FB2502 JW T2502 HDT Q2501 2SC3311A C2520 0.015 :MPS R2529 39 2W :RS R2525 47 :CHIP R2565 100 :CHIP R2517 100 :CHIP C2518 0.47 :MPS Q2502 2SA1309 3 D2514 ERA91-02 R2558 100k :CHIP L2506 4.7mmH 1.4Vp-p (V) Q2505 2SC3746 R2526 2.2k :CHIP C2521 1000 :HT C2522 0.0022 200V :PT D2507 1SS119 R2530 1.5 1/2W :FPRD R2538 22 3W :RS R2539 22 3W :RS C2528 C2530 C2531 0.0017 0.0017 330p 2kV 1.6kV 1.6kV :PP :PP R2549 10k :CHIP !∞ R2556 10k :CHIP 500Vp-p (H) !§ 4 D2511 DD54SCLS Q2515 DTC144EKA Q2508 2SC5450-CA 10Vp-p (H) Q2519 DTC144EKA R2540 22 3W :RS !¶ 2.8Vp-p (V) !• D2510 RH-1AV1 1.3Vp-p (V) 940Vp-p (H) 5 11-19 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-19 E F G H G CXA1544M (IC515) G MC14053BF (IC516) TC4S30F (IC522, 526) TC74HC4538/4538AF (IC503, 509, 510, 529) 1 24 V CC GND 1 V REF WIND COMPARATOR V REF 2 T IN 3 DUTY CONT DELAY 22 PHASE ADJ PHASE CONT 2 15 B.COM EDGE DETECT (SELECT) 1 C1 3 C.COM 4 5 VDD VDD 2-C 2-CR 2-RD 2-CK 2-CR 2-Q 2-Q 16 15 14 13 12 11 10 9 14 A.COM 2 13 A1 OPEN 21 DUTY ADJ COMP B0 16 VDD OPEN CO 5 12 A0 INH 6 11 A VEE 7 VSS 8 GEN AGC 1 23 DRIVE OUT DELAY ADJ 4 CAGC 1 5 B1 3 4 10 B OPEN 20 GND C 9 GEN DTC 6 2 19 RAGC V CC OUTPUT START START (V CC > 9V) STOP (VCC < 6V) IN 1(+) 7 1 2 3 4 5 6 7 8 1-C 1-CR 1-RD 1-CK 1-CK 1-Q 1-Q GND TC4S71F (IC2501) AGC 18 RAGC 2 TDA8172 (IC2503) 17 IN 2(+) Q CLOCK Q CLR 3Q 14 3Q 15 4D 16 3D 4Q 16 IN 2(-) 4Q FB 1 9 MC74HC175FEL (IC524) VCC IN 1(-) 8 13 12 11 10 9 Q Q CLR IN B 1 OUTPUT STAGE SUPPLY 6 5 VDD V CC 2 FLYBAK GEN 3 IN A 2 CORRECTOR 1 10 15 FB 2 CK D FLYBAK GENERATOR D CK 4 OUT X VSS 3 INVERTING IN 1 14 CORRECTOR 2 OUT 1 11 POWER AMPLIFIER 5 OUTPUT NON INVERT IN 7 P. GND 12 CK CLR Q 13 OUT 2 D D CK CLR Q Q Q TERMINAL PROTECTION 1Q 1Q 1D 2D 2Q 2Q GND TDA9106 (IC507) VFOCUS EWOUT VFLY VOUT VDCOUT VCAP VREF VAGCCAP VGND VBLKOUT HBLKOUT 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 CORNER CORRECTION (2 6 BITS) X SYNC INPUT SYNC SELECT PROCESSOR (2 BITS) LATCH LATCH LATCH LATCH 2 3 4 5 6 7 8 9 10 X 2 6 BITS 11 GEOMETRY TRACKING LATCH X2 – + DAC DAC DAC DAC VPOS 7 BITS DAC VCC REG AMP VERTICAL OSCILLATOR RAMP GENERATOR S AND C CORRECTION AMP IC2 INTERFACE 2 3 4 5 6 7 8 SW0 DAC4 DAC3 DAC2 DAC1 DAC0 GND KEY BAL 6 BITS PHASE COMPARATOR 10 Cathode MOIRE PROCESSOR (5 BITS) B C D SAFE FREQ. 2 BITS SAFETY PROCESSOR AMP&KEYST 2 5 BITS X 22 PHASE/FREQUENCY COMPARATOR H-PHASE(7 BITS) VREF VCC 2 3 4 5 6 7 8 9 10 11 FC2 FC1 R0 FREE RUNNING 5 BITS 1 C0 9 Vcc 5 VCC 11-20 A 8 Comparator Output HGND 7 GND HFLY 6 Drain HREF 5 Zero Current Sensing PLL2C 4 OUT 4 Source PLL1INHIB 3 VEE 3 Input Voltage Sensing H-SAWTOOTH GENERATOR MOIRE 2 – 2 Gate HOUT BUFFER H-DUTY (5 BITS) VSYNC H-FLY S/G 1 + 1 Drain SPIN BAL X 2 6 BITS PHASE SHIFTER LOCK/UNLOCK IDENTIFICATION LA6500 (IC2504) X 12 13 14 15 16 17 18 19 20 21 PLL1F 1 SW1 6 BITS 6 BITS HFOCUS AMP XRAY AMP HPOS AMP 5 VAMP 7 BITS RESET GENERATOR 11-20 HOUTCOL 1 HLOCKCAP 4 BLANKING GENERATOR 7 BITS HOUTEM POWER ON RESET VREF VFLY VSYNC HFLY LOCK I2C DECODER GND LEVEL CONVERTER 41 VCC LEVEL CONVERTER LATCH 42 OPEN COLLECTOR HFOCUSCAP LEVEL CONVERTER VSYNCIN MZ1540 (IC601) TEST 9 GND VSYNCOUT SW2 10 8 HOUT SW3 11 7 HLOCKOUT SAD0 12 6 H/HVIN SAD1 13 5 5V SAD2 14 4 SCL SDA 15 3 SDA SCL 16 2 GND VCC CXA1875AM (IC508, 512) 1 CLEAR 4 3 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H G1 G1 1 G1 BOARD CN1601 5P WHT :VH R1602 3.3 :FPRD T1601 SRT FB1601 D1604 P6KE170 D1603 SC311-06 D1606 D10SC9M D1605 D1NL20U C1604 220 :HT D1602 RD6.8SB2 R1601 47 :CHIP C1601 100 10V C1602 0.1 25V B:CHIP D1601 RD6.8ESB2 F1603 5A 125V PH601 PC123FY2 IC1601 TOP224Y-BB R1604 22 :CHIP R1605 R1607 2.2k 270 :CHIP :CHIP R1603 10k :CHIP R1606 1k :CHIP IC1602 µPC1093J-T Q1602 DTC114GKA PH602 PC123FY2 C1611 R1611 2200 10V 10 :CHIP :HT L1601 COIL L1602 47µH CN1602 3P WHT-L :VH 2 C1605 47 25V :HT Q1601 DTA114GKA C1607 C1608 R1610 4700 4700 1k 10V 10V :CHIP :HT :HT R1609 4.7k :RN-CP C1609 0.1 25V B:CHIP D1607 RD5.1ESB3 R1613 2.2k :RN-CP R1612 10k C1610 :RN-CP 10 :HT C1606 R1608 4.7k 0.01 B:CHIP :RN-CP Q1603 DTC114GKA C1603 10 :HT 3 G1 –B SIDE– SUFFIX: -11 4 5 11-21 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-21 E F G H HA HA 1 HA BOARD 2 HA –A SIDE– SUFFIX: -13 3 HA –B SIDE– SUFFIX: -13 4 5 11-22 A B C D 11-22 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H HA HA NJU3716M (IC201, 202) 1 CN202 10P WHT :S-MICRO S231 C308 0.01 F:CHIP R308 4.7k :CHIP D231 RD6.2SB 1 24 VDD P8 2 23 P6 P9 3 22 P5 P10 4 21 P4 P11 5 20 P3 P2 LATCH Q201 DTC144EKA R307 4.7k :CHIP TP202 TP203 C307 0.01 F:CHIP R209 1k :CHIP R217 47k :CHIP R208 R216 4.7k 47k :CHIP :CHIP R207 1k :CHIP D215 MA111 S215 D216 MA111 S216 TP204 S217 R206 1k :CHIP CN201 6P WHT :S-MICRO P7 S218 R205 100k :CHIP R215 47k :CHIP S201 D201 MA111 S202 D202 MA111 D217 MA111 S203 D203 MA111 D218 MA111 S204 D204 MA111 S205 D205 MA111 R210 100k :CHIP S219 D219 MA111 S220 D220 MA111 S206 D206 MA111 S221 D221 MA111 S207 D207 MA111 S222 D222 MA111 S208 D208 MA111 S209 D209 MA111 S210 D210 MA111 S211 D211 MA111 S212 D212 MA111 S213 D213 MA111 R201 560 :CHIP IC202 NJU3716M IC201 NJU3716M R202 560 :CHIP D223 CL-155Y/PG R203 560 :CHIP D224 CL-155Y/PG R204 560 :CHIP D225 CL-155Y/PG R211 33k :CHIP D226 CL-155Y/PG S214 D214 MA111 C306 0.01 F:CHIP R306 4.7k :CHIP R305 4.7k :CHIP S232 C305 0.01 F:CHIP C304 0.01 F:CHIP R304 4.7k :CHIP R303 4.7k :CHIP Vss 6 19 P12 7 18 P13 8 17 P1 P14 9 16 CLR 15 STB SHIFT REGISTER 2 CONTROL P15 10 P16 11 14 CLK SO 12 13 DATA S233 C303 0.01 F:CHIP C302 0.01 F:CHIP R302 4.7k :CHIP R301 4.7k :CHIP S234 3 C301 0.01 F:CHIP Q202 2SD1834 TP201 TP205 R212 82k :CHIP R213 33k :CHIP R214 82k :CHIP Q203 2SD1834 4 C217 0.01 F:CHIP C211 C212 C201 C202 C203 C204 C205 C206 C207 C213 C214 C215 0.01 0.01 0.01 0.01 100µF 100µF 100µF 100µF 100µF 100µF 100µF 0.01 F:CHIP F:CHIP F:CHIP F:CHIP 6.3V 6.3V 6.3V 6.3V 6.3V 6.3V 6.3V F:CHIP C216 0.01 F:CHIP 5 11-23 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-23 E F G H HB HB NJU3716M (IC101, 102) 1 P7 1 24 VDD P8 2 23 P6 P9 3 22 P5 P10 4 21 P4 P11 5 20 P3 S101 D101 MA111 Vss 6 19 P2 S102 D102 MA111 P12 7 18 S103 D103 MA111 P13 8 17 P1 S104 D104 MA111 P14 9 16 CLR S105 D105 MA111 P15 10 15 STB S106 D106 MA111 P16 11 14 CLK SO 12 13 DATA R126 47k :CHIP R127 47k :CHIP R117 4.7k :CHIP CN101 6P RED :S-MICRO Q103 DTC144EKA S107 D107 MA111 S108 D108 MA111 S109 D109 MA111 S110 D110 MA111 IC102 NJU3716M R115 1k :CHIP R114 1k :CHIP R113 1k :CHIP 2 R125 47k :CHIP IC101 NJU3716M R116 100k :CHIP R112 100k :CHIP D111 RD6.2SB D127 CL-155Y/PG R107 560 :CHIP R101 560 :CHIP D121 CL-155Y/PG TP101 R108 560 :CHIP D128 CL-155Y/PG R102 560 :CHIP D122 CL-155Y/PG R109 560 :CHIP D129 CL-155Y/PG R103 560 :CHIP D123 CL-155Y/PG R110 560 :CHIP D130 CL-155Y/PG R104 560 :CHIP D124 CL-155Y/PG R105 560 :CHIP D125 CL-155Y/PG C101 C102 47µF 47µF C111 0.01 F:CHIP C112 0.01 F:CHIP C113 0.01 F:CHIP R106 560 :CHIP D126 CL-155Y/PG R122 82k :CHIP SHIFT REGISTER CONTROL TP102 3 Q101 2SD1834 LATCH HB BOARD R121 33k :CHIP R123 33k :CHIP R124 82k :CHIP Q102 2SD1834 HB –A SIDE– 4 SUFFIX: -13 5 HB –B SIDE– SUFFIX: -13 11-24 A B C D 11-24 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H HC, HD HC, HD LTC490CS8 (IC13) 1 HC BOARD 8 A IN 1 VDD R OUT 2 B A C C B A D IN 3 [HC BOARD] Vcc Y0 Y1 Y2 Y3 Y4 Y5 T6 16 15 14 13 12 11 10 9 Y0 Y1 Y2 Y3 Y4 Y5 A B Y7 1 2 3 4 5 6 7 8 A B C G2A G2B G1 Y7 GND 1Y3 2A3 1Y4 2A4 TC74VHC244F (EL) (IC12) 2A3 A-3 A-1 A-1 A-2 C-1 C-3 C-3 B-3 G1 G2B 1Y2 2 G2A C 2A4 2 2 Y6 1Y1 20 19 18 17 16 15 14 13 12 11 3 3 7 8 9 10 2Y1 GND 6 1A4 5 1A3 4 2Y3 3 1A1 2 1G 1 2Y2 3 1A2 * 1 2Y4 Q4 TP2 TP3 TP4 TP6 TP7 TP8 TP9 * * * * * B-2 A-1 B-3 B-5 B-4 B-3 B-3 B-5 B-1 B-1 B-2 A-1 B-2 B-4 TC74VHC138F (EL) (IC3) 1 2G IC1 IC2 IC3 IC4 IC5 IC6 IC7 IC8 IC9 IC10 IC11 IC13 IC14 IC21 5 Y OUT Vcc * A-1 * A-1 * A-1 A-1 A-1 * A-2 * A-3 * A-2 A-1 6 Z OUT D 4 GND * : B SIDE D1 D2 D3 D4 D5 D6 D7 D8 D9 7 B IN R TC74VHC574F (EL) (IC11) 4 4 Vcc 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q CLK 20 19 18 17 16 15 14 13 12 11 4 Q OE Q OE Q OE Q OE Q OE Q OE Q OE Q OE D CK D CK D CK D CK D CK D CK D CK D CK 5 1 2 3 4 5 6 7 8 OC 1D 2D 3D 4D 5D 6D 7D 9 10 8D GND 5 5 HC –A SIDE– HC –B SIDE– SUFFIX: -15 SUFFIX: -15 11-25 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-25 E F G H HC, HD HC, HD C54 C56 C58 C60 C62 C64 0.01 0.01 0.01 0.01 0.01 0.01 C53 F:CHIP C55 F:CHIP C57 F:CHIP C59 F:CHIP C61 F:CHIP C63 F:CHIP C65 0.01 0.01 0.01 0.01 0.01 0.01 0.01 F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP 1 R87 R89 R91 R93 R79 R81 R83 R85 R21 R23 R25 R27 100k 100k 100k 100k 100k 100 k 100k 100k 1k 1k 1k 1k :CHIP:CHIP:CHIP:CHIP :CHIP:CHIP :CHIP:CHIP:CHIP:CHIP:CHIP:CHIP R88 R90 R92 R94 R80 R82 R84 R86 R22 R24 R26 R28 100k 100k 100k 100k100k 100k 100k 100k 1k 1k 1k 1k :CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP CN102 9P JW1 (5) TP1 TP2 JW2 (10) IC2 PST529 C R6 10k :CHIP 2 D105 RD6.2SB C4 0.01 F:CHIP C1 10pF CH:CHIP D102 RD6.2SB D104 RD6.2SB X1 R1 10k :CHIP R2 C2 0 10pF :CHIP CH:CHIP R3 C68 10k 0.01 R4 F:CHIP :CHIP 10k :CHIP D101 RD6.2SB D103 RD6.2SB IC3 TC74VH C138F( CN2 9P FL4 TP3 FL3 C50 0.01 F:CHIP FL5 R70 100k :CHIP FL2 IC13 LTC490 CS8 TP5 TP4 R5 10k :CHIP R7 100k :CHIP 3 C67 0.01 F:CHIP FL1 R68 100k :CHIP D2 RD6.2SB-T1 D3 D5 RD6.2SB-T1 D4 RD6.2SB-T1 RD6.2SB-T1 IC10(1/6) TC74VHC14F(EL) R61 R63 R65 R67 47k 47k 47k 47k IC9(1/6) :CHIP :CHIP :CHIP :CHIP TC74VHC14F(EL) R60 R62 R64 R66 47k 47k 47k 47k IC9(2/6) TC74VHC14F(EL) :CHIP :CHIP :CHIP :CHIP IC1 HD6473 258-P1 0 IC11 TC74VH C574F( EL) IC9(5/6) TC74VHC14F(EL) R71 100k :CHIP R72 100k R73 :CHIP 100k :CHIP R74 100k R75 :CHIP 100k :CHIP R76 100k R77 :CHIP 100k :CHIP R78 100k :CHIP CN3 10P 4 IC10(2 /6) TC74VHC14F(EL) FL6 SUFFIX: -11 IC9(6/ 6) TC74VHC14F(EL) IC9(3/ 6) TC74VHC14F(EL) D8 RD6.2SB-T1 CN4 6P WHT :S-MICRO HD –B SIDE– IC9(4/ 6) TC74VHC14F(EL) R41 10k :CHIP R42 10k :CHIP FL10 R14 1k :CHIP R20 10k :CHIP IC10(5 /6) TC74VHC14F(EL) R12 10k :CHIP R16 10k :CHIP R13 10k :CHIP FL9 R19 10k :CHIP C89 100 6.3V AL-CP FL8 FL7 FL11 D6 RD6.2SB-T1 R44 10k :CHIP R43 10k :CHIP 5 FL14 FL12 D1 RD6.2SB-T1 FL15 C81 100 6.3V AL-CP JR2 0 :CHIP IC12 TC74VH C244F( EL) R15 1k :CHIP C83 C84 C85 C86 C87 100 100 100 100 100 6.3V 6.3V 6.3V 6.3V 6.3V AL-CP AL-CP AL-CP AL-CP AL-CP C52 C82 0.01 220 F:CHIP 6.3V L2 FL13 FL16 CN5 6P RED :S-MICRO D7 RD6.2SB-T1 11-26 A B C D 11-26 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H MA CXD1095BQ (IC112) NC PX1 PX0 A2 A1 A0 CS RD WR GND RST CLR D7 D6 D5 D4 D3 NC NC 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 A0 10 A1 9 A2 CONTROL 32 D2 PX2 52 8 8 LATCH 8 31 D1 8 PA0 54 8 PA1 55 LATCH VDD 8 LATCH 8 8 PA3 59 LATCH 8 8 LATCH A5 5 A6 4 CS 5 1 A7 3 A8 25 A9 24 ADDRESS BUFFER LOW DECODER MEMORY CELL ARRAY 3.3V DETECT 12 I/O2 OUTPUT DATA BUFFER COLUMN I/O CIRCUIT 13 I/O3 DIODE 4.2V DETECT 15 I/O4 16 I/O5 17 I/O6 1 18 I/O7 INPUT DATA CONTROL A14 1 INPUT DATA BUFFER 2 GND OPEN COLLECTOR 19 I/O8 3 4 CS VBAT CE 20 25 GND PA4 60 PA5 61 6 A13 26 26 VDD 8 COLUMN DECODER 7 A4 27 PD5 8 58 8 A3 A12 2 28 PD6 VOUT 6 7 11 I/O1 A11 23 29 PD7 8 VCC 8 A10 21 30 D0 8 PA2 56 GND 57 MM102BFB (IC110) LC35256DM-70-TLM (IC111) 51 PX3 53 MA WE 27 28 VCC OE 22 14 GND 24 PD4 8 23 PD3 8 PA6 62 2 22 PD2 21 PD1 PA7 63 DATA SELECT PB0 64 20 PD0 MAX490ECSA (IC113) 18 TC74VHC138F (FL) (IC109) 19 NC 17 PC7 16 PC6 15 PC5 14 PC4 13 PC3 12 PC2 11 PC1 GND PB7 10 PC0 9 8 PB6 7 PB5 6 PB4 5 PB3 4 PB2 3 PB1 2 NC NC 1 VCC 1 8 A RO 2 7 B DI 3 6 Z 5 Y R Vcc Y0 Y1 Y2 Y3 Y4 Y5 T6 16 15 14 13 12 11 10 9 Y0 Y1 Y2 Y3 Y4 Y5 B C G2A G2B G1 Y7 1 2 3 4 5 6 7 8 A B C G2A G2B G1 Y7 GND D HD6435368AX06M (IC106) GND 4 PORT 1 79 P1 7 /TMO 78 P1 6 /IRQ 1 /ADTRG 77 P1 5 /IRQ 0 76 P1 4 /WAIT 75 P1 3 /BREQ 74 P1 2 /BACK 73 P1 1 /E 72 P1 0 /Ø XTAL EXTAL RAM 2k BYTE INTERRUPT CONTROLLER 10-BIT A/D CONVERTER (x8 CHANNEL) CLOCK OSC MD 2 MD 1 MD 0 STBY RES WAIT STATE CONTROLLER 9 10 PORT 2 4 P2 4 /WR 3 P2 3 /RD 2 P2 2 /DS 1 P2 1 /R/W 80 P2 0 /AS PROM / MASK OM 32k BYTE (H8 / 534) 62k BYTE (H8 / 536) 20 P3 7 /D 7 19 P3 6 /D 6 18 P3 5 /D 5 17 P3 4 /D 4 16 P3 3 /D 3 15 P3 2 /D 2 14 P3 1 /D 1 13 P3 0 /D 0 PORT 3 CPU WATCHDOG TIMER PORT 7 49 46 45 44 7 6 PORT 8 54 53 52 48 47 DATA TRANSFER CONTROLLER 50 55 70 69 8-BIT TIMER P7 7 /FTOA 1 P7 6 /FTOB 3 /FTCI 3 P7 5 /FTOB 2 /FTCI 2 P7 4 /FTOB 1 /FTCI 1 P7 3 /FTI 3 /TMRI P7 2 /FTI 2 P7 1 /FTI 1 P7 0 /TMCI 63 62 61 58 57 56 8 SERIAL COMMUNICATION INTERFACE (x2 CHANNEL) 59 64 PWM TIMER (x3 CHANNEL) P8 7 /AN 7 P8 6 /AN 6 P8 5 /AN 5 P8 4 /AN 4 P8 3 /AN 3 P8 2 /AN 2 P8 1 /AN 1 P8 0 /AN 0 67 66 65 16-BIT FREE RUNNING TIMER (x3 CHANNEL) 68 11 PORT 9 P9 7 /SCK 1 P9 6 /RXD 1 P9 5 /TXD 1 P9 4 /SCK 2 /PW 3 P9 3 /RXD 2 /PW 2 P9 2 /TXD 2 /PW 1 P9 1 /FTOA 3 P9 0 /FTOA 2 NMI A DATA BUS (LOW ORDER) DATA BUS (HIGH ORDER) 1 2 3 4 5 6 7 8 PORT 5 PORT 4 38 39 40 41 30 31 32 33 34 35 36 37 21 22 23 24 25 26 27 28 P6 0 /IRO 2 /A 16 P6 1 /PW 1 /IRQ 3 /A 17 P6 2 /PW 2 /IRQ 4 /A 18 P6 3 /PW 3 /IRQ 5 /A 19 P5 0 /A 8 P5 1 /A 9 P5 2 /A 10 P5 3 /A 11 P5 4 /A 12 P5 5 /A 13 P5 6 /A 14 P5 7 /A 15 P4 0 /A 0 P4 1 /A 1 P4 2 /A 2 P4 3 /A 3 P4 4 /A 4 P4 5 /A 5 P4 6 /A 6 P4 7 /A 7 A15 A14 A13 A12 A11 A10 A9 A8 A16 48 BYTE 47 X DECODER 4,194,304 CELL MATRIX Y GATE ADDRESS LATCH 9 NC 10 NC Y DECODER I/O BUFFER DATA LATCH STB GND 46 DQ15/A–1 45 DQ7 44 DQ14 43 DQ6 42 DQ13 41 DQ5 40 DQ12 39 DQ4 38 4 VCC 37 STB 12 PORT 6 3 MBM29F400BC-90PF (IC108) 11 ADDRESS BUS Y6 WE CONTROL CIRCUIT LOW VCC DETECTOR CIRCUIT RESET 13 NC 14 NC RY/BY 15 16 NC A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24 WRITE/ERASE PULSE TIMER DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 36 35 34 33 32 31 30 29 WRITE CIRCUIT RY/BY BUFFER ERASE CIRCUIT CHIP ENABLE/ OUTPUT ENABLE CIRCUIT OE 28 GND 27 CE 26 A0 25 5 11-27 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-27 E F G H MA MA 1 MA BOARD [MA BOARD] * : B SIDE 2 3 4 D101 D102 D103 D104 D105 D106 D107 D108 D109 * * * * * * C-4 C-4 B-4 B-4 A-5 A-5 A-5 A-5 C-4 IC101 IC102 IC103 IC104 IC106 IC107 IC108 IC109 IC110 IC111 IC112 IC113 * B-1 C-4 * B-4 * A-4 B-2 * A-3 * A-3 * A-3 * C-3 * A-4 B-3 A-4 Q102 Q103 Q104 Q105 Q106 * A-4 * B-1 C-1 * B-1 C-1 TP101 TP102 TP103 TP104 TP105 TP106 TP107 TP108 TP109 TP110 TP111 TP112 TP113 TP114 TP115 TP116 TP117 B-1 B-1 B-1 B-1 B-4 B-4 B-4 B-1 C-5 C-2 B-4 A-2 A-2 A-5 * A-5 A-4 B-4 MA –A SIDE– MA –B SIDE– SUFFIX: -11 SUFFIX: -11 5 11-28 A B C D 11-28 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H MA MA IC108 MBM29F400BC-90PF PROGRAM ROM C162 C163 100 0.01 6.3V F:CHIP :HT-CP R140 R144 R148 R151 100k 100k 100k 100k :CHIP :CHIP :CHIP :CHIP R164 100k :CHIP R138 R142 R146 R150 100k 100k 100k 100k :CHIP :CHIP :CHIP :CHIP IC113 MAX490ECSA RS422 DRIVE IC111 LC35256DM-70-TLM WORK RAM THP102 FL112 C166 100 6.3V :HT-CP TP116 D102 RD6.2SB-T1 TP115 1 CN105 9P D101 FL113 RD6.2SB-T1 R102 100k :CHIP FL115 D109 RD6.2SB FL111 D104 RD6.2SB-T1 FL110 CN102 50P C101 0.01 F:CHIP C103 100 6.3V :HT-CP R103 100 :CHIP R104 100 :CHIP D103 RD6.2SB-T1 IC106 HD6435368AX06M SYSTEM CONTROL R112 100k:CHIP R111 100k:CHIP R110 100k:CHIP R109 100k:CHIP R108 100k:CHIP R107 100k:CHIP R106 100k:CHIP R105 100k:CHIP R137 10k :CHIP R136 10k :CHIP R135 10k :CHIP R153 10k :CHIP R152 10k :CHIP C112 100 6.3V :HT-CP TP104 2 R161 100k :CHIP IC107 TC74VHC04F(EL) C159 C161 100 6.3V 0.01 :HT-CP F:CHIP C133 100 6.3V :HT-CP C140 0.01 F:CHIP IC109 TC74VHC138F(EL) ADDRESS SELECTOR C129 100 6.3V :HT-CP R113 100 :CHIP C134 0.01 F:CHIP FL117 IC102 TC7W32FU(TE12R) C116 100 6.3V :HT-CP R101 100k :CHIP C117 0.01 F:CHIP IC110 MM1026BFB RESET R158 10k :CHIP R133 R139 R143 1k 1k 1k :CHIP :CHIP :CHIP R131 R134 R141 1k 1k 1k :CHIP :CHIP :CHIP R117 100 :CHIP C136 C139 100 6.3V 0.01 :HT-CP F:CHIP C119 0.01 F:CHIP C121 100 6.3V :HT-CP JR101 0 :CHIP R124 100 :CHIP FL103 R127 4.7k :CHIP TP102 Q105 2SB1132-T100 LED DRIVE Q103 DTC144EKA INV R116 100 :CHIP IC103 SN74HC05ANSR IC103 SN74HC05ANSR R121 100k :CHIP C123 0.01 F:CHIP C118 100 6.3V :HT-CP FL108 R119 IC101 100k TC74VHC125F:CHIP FL107 IC103 C120 0.01 SN74HC05ANSR F:CHIP TP107 FL109 R118 100k :CHIP TP106 IC104 TC74HC30AF(EL) SLOT RECEIVER IC103 R122 SN74HC05ANSR 100 :CHIP C111 100 6.3V :HT-CP R120 100 :CHIP R190 R191 R193 R194 820 820 820 820 TP108 C125 C128 C132 100 100 100 6.3V 6.3V 6.3V :HT-CP :HT-CP :HT-CP R195 820 IC112 CXD1095BQ PARALLEL I/O C149 100 6.3V :HT-CP C168 C169 100 0.01 6.3V F:CHIP :HT-CP R197 10k :CHIP L101 100µH R196 10k :CHIP C154 C151 C148 C124 C127 C131 C137 C142 C145 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 C122 0.01 F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP 100 6.3V :HT-CP Q104 DTC144EKA INV IC103 SN74HC05ANSR C147 C150 C153 C130 C135 C141 C144 0.01 0.01 0.01 0.01 0.01 0.01 0.01 F:CHIP F:CHIP F:CHIP F:CHIP F:CHIP F:CHIPF:CHIP C115 0.01 F:CHIP 3 R180 10k :CHIP BT1 CR2025 R159 1k :CHIP IC103 SN74HC05ANSR R125 4.7k :CHIP R179 820 :CHIP R183 R178 10k 1.5k :CHIP :CHIP R167 100k :CHIP JR103 100K :CHIP CN103 7P RED:L :S-MICRO R181 820 :CHIP R165 100k :CHIP TP105 IC101 TC74VHC125F TP101 FL104 R189 100 :CHIP R126 100 :CHIP C164 C165 0.01 22 F:CHIP 35V :HT-CP R169 100k :CHIP R145 1k :CHIP R130 1k :CHIP R182 R184 R185 R186 820 820 820 820 :CHIP:CHIP :CHIP:CHIP FL114 R147 1k TP111 :CHIP C106 C105 10p 22p CH:CHIP CH:CHIP R192 100k :CHIP THP101 C113 0.01 F:CHIP TP103 R188 100 :CHIP FL123 FL120 TP117 R128 100k :CHIP R132 100k :CHIP X101 20.0MHz IC101 TC74VHC125F R162 100k :CHIP R129 100k :CHIP R123 1M :CHIP R115 100 :CHIP R163 100k :CHIP C114 0.01 F:CHIP C109 100 6.3V :HT-CP C102 100 C104 6.3V 0.01 :HT-CP F:CHIP R187 100 :CHIP R157 100k :CHIP R156 100k :CHIP R155 100k :CHIP R154 100k :CHIP 4 FL124 R172 1.5k :CHIP C160 0.01 F:CHIP C126 0.01 F:CHIP Q106 2SB1132-T100 LED DRIVE R166 100 :CHIP R168 100 :CHIP R173 100 :CHIP R171 100 :CHIP R170 100 :CHIP FL105 R160 10k :CHIP C108 100 6.3V :HT-CP 5 C110 0.01 F:CHIP R198 100k :CHIP IC102 TC7W32FU(TE12R) C172 100 C171 6.3V 0.01 :HT-CP F:CHIP IC107 TC74VHC04F(EL) IC101 TC74VHC125F TP109 TP110 TP112 TP113 TP114 IC107 TC74VHC04F(EL) IC107 TC74VHC04F(EL) IC107 TC74VHC04F(EL) CN101 10P Q102 DTA144EKA-T146 SLAVE CPU RESET IC107 TC74VHC04F(EL) 11-29 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-29 E F G H MB MB MAX487ECSA (IC1103, 1106) MAX3100CEE (IC1105, 1108) 1 T RO R 1 8 (MASKS) VCC TRANSMIT-DONE (TM) 9 DATA-RECEIVED (RM) RE 2 7 Pt B TX-BUFFER REGISTER 3 DI 4 D MB BOARD 6 A 5 GND 7 DIN 1 CS 4 SCLK 3 DOUT 2 IRQ 15 TX 10 X1 9 X2 B0 B1 B2 B3 SPI INTERFACE 6 TX-SHIFT REGISTER D0t–D7t Pt SHDN INTERRUPT LOGIC PARITY (PM) FRAMING ERROR (RAM)/ RECEIVE ACTIVITY 9 DE (SOURCES) R Pr RA/FE BAUD-RATE GENERATOR RA ACTIVITY DETECT FE START/STOPBIT DETECT A 2 B C C A B Pr RX-SHIFT REGISTER D0r–D7r 14 RX 9 [MB BOARD] * : B SIDE 3 4 D1100 D1101 D1102 D1103 D1104 D1105 D1106 D1107 D1108 D1109 D1110 D1111 D1112 D1113 D1114 D1115 D1116 D1117 D1118 IC1100 IC1101 IC1102 IC1103 IC1104 IC1105 IC1106 IC1107 IC1108 IC1109 IC1110 IC1112 TP1100 TP1101 TP1102 TP1103 TP1104 TP1106 TP1107 TP1108 TP1109 TP1110 TP1111 TP1112 TP1113 C-2 B-3 B-3 B-2 B-2 B-1 C-1 C-2 B-3 C-2 B-4 C-4 C-4 11 CTS I/O 16 VCC 8 GND MB90096PF-127/G-178 (IC1107, 1110) 2 2 DISP 14 20 BOUT VSYNC 13 EVEN 11 RESET 5 19 ROUT DISPLAY CONTROL CS 26 SIN 25 SCLK 24 18 GOUT DISPLAY OUTPUT SERIAL INPUT CONTROL 17 IOUT CONTROL 16 VOB1 15 VOB2 TRE 23 COMMAND TABLE ROM CONTROL DISPLAY MEMORY VRAM 9 DOCKO FONT ROM 6 (32FIGURE 16LINE) TEST 22 VCC COMMAND TABLE ROM 3 21 V3V DOT CLOCK 28 AV3V 27 AVCC (16KByte) 3 8 DOT CLOCK HSYNC 12 GENERATOR DOCKI CPOUT VCOIN 10 FH (PLL CIRLOIT) 1 3 7 GND 4 VCO GND 2 VCO GNC MC74HC589AFEL (IC1112) 4 Serial Data Input 4 5 5 MB –A SIDE– MB –B SIDE– SUFFIX: -11 SUFFIX: -11 11-30 A RX-BUFFER REGISTER 13 RTS Parallel Data Inputs 5 Pr 9 * * * * * B-1 A-1 B-1 A-3 B-3 C-2 * A-2 * B-2 C-2 * C-1 * B-3 * B-2 RX-BUFFER REGISTER 1 1 * A-3 * A-3 * A-4 * A-5 * C-1 * C-1 * C-1 * C-1 * C-1 * C-1 * A-2 * A-2 * A-2 * A-2 * A-2 * A-2 * A-1 * A-1 * C-1 Pr B C D SA 14 A 15 B 1 C 2 D 3 E 4 F 5 G 6 H 7 LCK 12 SCK 11 SS/PL 13 OE 10 Input Latch Shift Register 9 11-30 QH Serial Data Output BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H MB MB CN1105 9P WHT :S-MICRO 1 CN1102 50P TP1108 FL1112 TP1109 R1182 100 R1183 100 C1100 C1103 C1114 C1115 C1156 C1157 100 0.01 100 0.1 0.01 100 6.3V F:CHIP F:CHIP 6.3V F:CHIP 6.3V :AL-CP :AL-CP :AL-CP FL1113 R1108 100 :CHIP R1107 100 :CHIP R1106 100 :CHIP IC1100 TC74VHC02F MIX IC1100 TC74VHC02F MIX R1115 100 :CHIP R1114 100 :CHIP R1104 100 :CHIP R1103 100 :CHIP R1102 100 :CHIP R1101 100 :CHIP R1100 100 :CHIP R1167 47k :CHIP IC1107 MB90096PF-127 OSD R1137 R1138 R1140 0 82 300 :CHIP :RN-CP :RN-CP C1126 0.1 F:CHIP C1122 0.1 F:CHIP R1184 100 IC1110 MB90096PF-G-178 OSD R1148 R1149 82 300 :RN-CP :RN-CP C1127 100 6.3V :AL-CP R1128 100k :CHIP R1127 100k:CHIP C1142 C1141 100 0.01 6.3V F:CHIP :AL-CP R1185 100 L1101 100µH IC1101 TC74VHC125F(EL) C1139 0.1 F:CHIP L1102 100µH IC1101 TC74VHC125F(EL) R1147 0 :CHIP 2 R1126 100k:CHIP R1125 100k :CHIP R1123 R1122 R1121 R1120 R1112 100 :CHIP R1111 100 :CHIP R1110 100 :CHIP R1109 100 :CHIP C1128 0.1 F:CHIP C1160 0.01 B:CHIP 100k:CHIP 100k:CHIP 100k :CHIP 100k :CHIP C1118 C1119 0.01 1.0 B:CHIP B:CHIP C1129 100 6.3V :AL-CP R1131 100k :CHIP R1118 R1119 100 15k :CHIP :CHIP R1132 100k :CHIP IC1104 TC74VHC14F(EL) C1145 100 6.3V :AL-CP C1140 0.1 F:CHIP IC1100 TC74VHC02F MIX C1124 0.1 F:CHIP IC1104 TC74VHC14F(EL) C1143 0.01 F:CHIP C1135 C1136 1.0 0.01 B:CHIP B:CHIP C1161 0.01 B:CHIP C1104 C1106 100 0.01 6.3V F:CHIP :AL-CP R1113 100k :CHIP IC1100 TC74VHC02F MIX TP1101 TP1104 IC1101 TC74VHC125F(EL) R1174 100k :CHIP IC1102 TC74VHCU04F(EL) R1175 100k :CHIP IC1102 TC74VHCU04F(EL) R1176 100k :CHIP IC1102 TC74VHCU04F(EL) R1181 100k :CHIP C1150 C1152 100 0.01 6.3V F:CHIP :AL-CP IC1101 TC74VHC125F(EL) IC1102 TC74VHCU04F(EL) R1177 100k :CHIP C1162 0.0022 C1116 C1117 0.01 100 F:CHIP 6.3V :AL-CP IC1105 MAX3100CEE UART R1172 47k :CHIP 3 R1171 4.7k :CHIP C1125 100 C1123 0.01 6.3V F:CHIP :AL-CP C1109 C1111 0.01 100 F:CHIP 6.3V :AL-CP TP1106 IC1104 TC74VHC14F(EL) TP1107 IC1104 TC74VHC14F(EL) R1170 4.7k :CHIP TP1102 TP1103 R1130 47k :CHIP R1180 4.7k :CHIP R1145 47k :CHIP R1136 47k :CHIP R1133 47k :CHIP R1173 47k :CHIP CN1101 12P WHT :S-MICRO IC1104 TC74VHC14F(EL) IC1108 MAX3100CEE UART C1130 100 6.3V :AL-CP C1131 0.01 F:CHIP C1180 47p CH:CHIP IC1103 MAX487ECSA RS485 INTERFACE IC1106 MAX487ECSA RS485 INTERFACE C1112 0.01 F:CHIP IC1104 TC74VHC14F(EL) D1110 RD6.2SB PROTECTOR C1132 0.1 F:CHIP FL1102 R1144 10k :CHIP CN1100 9P RED :S-MICRO C1102 100 6.3V C1101 :AL-CP 0.1 F:CHIP C1107 100 6.3V :AL-CP R1117 1M :CHIP X1100 3.6864MHz C1133 0.1 F:CHIP FL1100 IC1102 TC74VHCU04F(EL) R1142 10k :CHIP D1103 RD6.2SB-T1 FL1101 C1137 0.1 F:CHIP C1138 0.1 F:CHIP FL1109 D1105 RD12SB FL1108 PROTECTOR D1104 RD12SB D1101 PROTECTOR RD6.2SB-T1 D1106 RD12SB PROTECTOR D1100 RD6.2SB-T1 R1187 0 R1186 0 R1188 0 R1161 100k :CHIP R1162 100k :CHIP R1163 100k :CHIP R1164 100k :CHIP R1165 100k :CHIP R1166 100k :CHIP C1144 0.01 F:CHIP C1146 0.01 F:CHIP C1147 0.01 F:CHIP C1148 0.01 F:CHIP C1149 0.01 F:CHIP C1151 0.01 F:CHIP C1153 0.01 F:CHIP C1154 0.01 F:CHIP FL1114 R1151 R1153 R1155 R1157 1k 1k 1k 1k :CHIP :CHIP :CHIP :CHIP R1152 R1154 R1156 1k 1k 1k :CHIP :CHIP :CHIP TH1100 FL1110 FL1115 FL1116 FL1117 FL1118 FL1119 FL1120 4 FL1121 TP1110 TP1111TP1112TP1113 R1159 1k :CHIP D1107 RD12SB PROTECTOR D1111 RD6.2SB PROTECTOR D1109 RD12SB PROTECTOR D1102 RD6.2SB-T1 C1110 15p C1108 IC1102 CH:CHIP 18p CH:CHIP TC74VHCU04F(EL) R1160 100k :CHIP C1158 C1159 0.01 100 F:CHIP 6.3V :AL-CP FL1111 TP1100 C1105 0.01 F:CHIP R1158 100k :CHIP IC1109 MAX202CSE-TE2 RS232C INTERFACE C1120 C1121 0.01 100 F:CHIP 6.3V :AL-CP FL1103 L1100 100µH IC1112 MC74HC589AFEL REMOTE2 DRIVER C1134 0.1 F:CHIP D1112 RD6.2SB PROTECTOR D1113 RD6.2SB PROTECTOR D1115 D1117 RD6.2SB RD6.2SB PROTECTOR D1116 PROTECTOR D1114 RD6.2SB RD6.2SB PROTECTOR PROTECTOR D1108 RD12SB PROTECTOR D1118 RD6.2SB PROTECTOR R1141 R1143 10k 10k :CHIP :CHIP R1189 0 5 CN1103 9P CN1104 9P CN1109 6P CN1107 9P CN1106 7P 11-31 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-31 E F G H YA, YB, YC YA, YB, YC 1 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k :CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP:CHIP :CHIP CN901 3P WHT PH D904 D901 D902 D903 D905 SPR-325MVW SPR-325MVW SPR-325MVW SPR-325MVWSPR-325MVW TALLY IND TALLY IND TALLY IND TALLY IND TALLY IND YA –B SIDE– SUFFIX: -11 2 CN921 6P D921 SLR-325DCT31 D923 SLR-325MCT31 POWER YB –B SIDE– D922 SLR-325VCT31 STANDBY SUFFIX: -11 3 D931 RD12SB CN931 8P D932 RD12SB CN932 8P YC –B SIDE– SUFFIX: -11 4 D933 RD12SB D934 RD12SB D935 6.2SB D936 RD12SB D937 RD12SB 5 11-32 A B C D 11-32 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H T T 1 T BOARD CN802 64P WHT CN803 64P WHT CN804 64P WHT CN805 8P WHT(-L) :S-MICRO CN801 11P WHT(-L) :S-MICRO 2 3 CN806 10P WHT(-L) :S-MICRO 4 T –A SIDE– T –B SIDE– SUFFIX: -11 SUFFIX: -11 5 11-33 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A A B C D 11-33 E F G H 1 2 3 4 5 11-34 A B C D 11-34 BVM-D14H1U/D14H5U/D14H1E/D14H5E/D14H1A/D14H5A E F G H The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des opérations ou entretiens de l’équipement à moins d’une permission écrite de Sony Corporation. Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind. Die Sony Corporation untersagt ausdrücklich die Vervielfältigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben für irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrüstung ohne ausdrückliche schriftliche Erlaubnis der Sony Corporation. English Sony Corporation 9-929-659-01 Broadcasting & Professional Systems Company 99JS16033-1 Printed in Japan ©1999.10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 1999:09:29 11:53:11 Producer : Acrobat Distiller 3.0 for Power Macintosh Title : BVM-D14H1U_Maintenance Manual Author : SONY B&P CO. Modify Date : 1999:12:01 17:03:25 Page Count : 158 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools