CSA CSA82304
User Manual: CSA82304
Open the PDF directly: View PDF 
.
Page Count: 29
| Download | |
| Open PDF In Browser | View PDF |
Certificate of Compliance Certificate: 1361537 (LR 42465) Master Contract: 159658 Project: 1361537 Date Issued: September 24, 2002 Issued to: GAI-Tronics Corporation 400E. Wyomissing Ave. Mohnton, PA 19540 USA Attention: Mr. Anthony F. Bianca The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' Issued by: Joe da Silva, C.E.T. Authorized by: Nick Alfano Operations Manager PRODUCTS CLASS 4818 02 - SIGNAL APPLIANCES - Audible - For Hazardous Locations Class I, Div 2, Groups A, B, C, D: Page/Party voice communication system, comprised of the following equipment: Part A Smart handset/speaker amplifier station, Model 701-902, rated 120V, 0.46 , 50/60Hz, with enclosure 7335-001 or 7335-005. Part B Smart speaker amplifier station, Model 751-901, rated 120V, 0.46 , 50/60Hz, with enclosure 733-001 or 7335005. Part C Smart series remote handset/speaker amplifier station, Model 723-801, rated 120V, 0.46 , 50/60Hz, with desk top five party remote subset model A02027 and enclosure 7245-004. The 'C' and 'US' indicators adjacent to the CSA Mark signify that the product has been evaluated to the applicable CSA and ANSI/UL Standards, for use in Canada and the U.S., respectively. This 'US' indicator includes products eligible to bear the 'NRTL' indicator. NRTL, i.e. National Recognized Testing Laboratory, is a designation granted by the U.S. Occupational Safety and Health Administration (OSHA) to laboratories which have been recognized to perform certification to U.S. Standards. FF02 DQD 507WD 2002/04/30 Certificate: Project: 1361537 1361537 Master Contract: 159658 Date: September 24, 2002 APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No. 94-M91 CSA Std C22.2 No.142-M1987 CAN/CSA-C22.2 No.157-92 - UL Std No. UL Std No. UL Std No. 1459 508 1604 - UL Std No. (Editions 1 to 9) UL Std No. (Edition 10) 50 - Special Purpose Enclosures Process Control Equipment Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations Telephone Equipment Industrial Control Equipment Electrical Equipment for Use in Class I and II, Division 2; Class III Hazardous (Classified) Locations Electrical Cabinets and Boxes 50 - Enclosures for Electrical Equipment MARKINGS a) Handset/speaker amplifier (701-902, 751-901 and 723-801) and Remote subset (A02027): For above equipment, the following data appears as part of the markings: submittor's name and/or trademark, model designation, electrical rating, hazardous location designation, identification of applicable enclosure, the CSA Monogram. Warning regarding substitution of components may impair suitability for use in Div. 2 as well as a Warning regarding to not disconnect equipment in hazardous locations unless power has switched off or the area is known to be non-hazardous. (b) Enclosures (7335-001, 7335-005, 733-001 and 7245-004): For above enclosures, the following data appears as part of the markings: submittor's name and/or trademark, model designation, intended (designed) usage. Note: This caution statement may be on a separate label or tag, plainly visible during installation. Enclosures (7335-001, 7335-005 and 733-001) In addition to the marking requirements of Item (b) as shown in the "Certificate of Compliance", the following statement appears on the unit: "CAUTION: NON-METALLIC ENCLOSURE DOES NOT PROVIDE GROUNDING BETWEEN CONDUIT CONNECTIONS. USE GROUNDING TYPE BUSHINGS AND JUMPER WIRES". Note: This caution statement may be on a separate label or tag, plainly visible during installation. DQD 507WD 2002/04/30 Supplement to Certificate of Compliance Certificate: 1361537 (LR42465) Master Contract: 159658 The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Product Certification History Project Date Description 1361537 Sept. 24/02 Original Certification. DQD 507WD 2002/04/30 Descriptive and Test Report MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Edition 1: September 24, 2002; Project 1361537 - Toronto Issued by Joe da Silva, C.E.T. Contents: Certificate of Compliance - Page 1 to 2 Supplement to Certificate of Compliance – Page 1 Description and Tests – Pages 1 to 5 PRODUCTS Part A Smart handset/speaker amplifier station, Model 701-902, rated 120V, 0.46 , 50/60Hz, with enclosure 7335-001 or 7335-005. Part B Smart speaker amplifier station, Model 751-901, rated 120V, 0.46 , 50/60Hz, with enclosure 733-001 or 7335005. Part C Smart series remote handset/speaker amplifier station, Model 723-801, rated 120V, 0.46 , 50/60Hz, with desk top five party remote subset model A02027 and enclosure 7245-004. The test report shall not be reproduced, except in full, without the approval of CSA International. F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Page No: 2 Date Issued: September 24, 2002 APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No. 94-M91 CSA Std C22.2 No.142-M1987 CAN/CSA-C22.2 No.157-92 - UL Std No. UL Std No. UL Std No. 1459 508 1604 - UL Std No. (Editions 1 to 9) UL Std No. (Edition 10) 50 - Special Purpose Enclosures Process Control Equipment Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations Telephone Equipment Industrial Control Equipment Electrical Equipment for Use in Class I and II, Division 2; Class III Hazardous (Classified) Locations Electrical Cabinets and Boxes 50 - Enclosures for Electrical Equipment MARKINGS Markings as indicated in C.O.C. must appear on CSA accepted Label. Refer to reports mentioned in description section of this report for further details and drawings of markings. ALTERATIONS Markings as indicated above. F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Page No: 3 Date Issued: September 24, 2002 FACTORY TESTS 1. The equipment at the conclusion of manufacture and before shipment, shall withstand for one min, without breakdown, the application of the following ac potentials: (a) 1000V for equipment rated 250V or less, and 1000V plus twice rated voltage for equipment rated at more than 250V between low voltage live parts and the enclosure if such circuits leave or enter the enclosure; (b) 1000V for equipment rated 250V or less, and 1000V plus twice rated voltage for equipment rated at more than 250V between live parts of low and extra-low voltage circuits and different low voltage circuits if such circuits leave or enter the enclosure; (c) 500V between extra low potential live parts and exposed non-current-carrying metal parts or ground terminal, if such circuits leave or enter the enclosure. 2. A transformer, if provided, shall withstand for one min without breakdown, the application of an ac potential of l000V plus twice the max voltage of the winding applied between each winding and all other windings, the core, and the enclosure; except that if the max voltage of a winding does not exceed 30V, the test voltage may be reduced to 500V ac for that winding. Ungrounded metallic shields are to be treated as windings when performing these dielectric strength tests. Notes: 1. As an alternative, potentials 20 percent higher may be applied for one second. 2. Where it is more convenient to do so, the dielectric strength tests may be made by applying a direct current voltage instead of an ac voltage, provided that the voltage used is 1.414 times the values specified above. 3. Capacitors in the secondary circuit may be disconnected during the dielectric strength tests specified in Items 1(a) to (c). The test specified in Item 1(c) shall be waived on grounded or Class 2 circuits. 4. 5. Transformer manufacturer's agreement to perform Test No 2 will be acceptable. Also, this test shall be waived on Certified transformers. Warning: The factory test(s) specified may present a hazard of injury to personnel and/or property and should only be performed by persons knowledgeable of such hazards and under conditions designed to minimize the possibility of injury. F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Page No: 4 Date Issued: September 24, 2002 DESCRIPTION Part A - Smart handset/speaker amplifier station, Models 701-902 with enclosures 7335-001 or 7335-005: (i) Smart handset/speaker amplifier station, Model 701-902 – Similar to presently CSA accepted smart handset/speaker amplifier model 701-802 which is presently CSA certified under report 159658-2500004743. The only difference between 701-902 and 701-801 is that model 701-902 uses different PC board construction and has a AC hum shield. Model 701-902 has been evaluated to CSA standards for use in Cl. I, Div. 2, Gps. A, B, C and D by UL under UL report E98383, Refer to copy of UL report attached to this report for complete description. (ii) Enclosure, Model 7335-001 and 7335-005 – These enclosures are presently CSA accepted to be used with handset/speaker amplifier model 701-802 and -804 under report 159658-2500004743. Refer to CSA report 159658-2500004743 for complete description. Part B - Smart handset/speaker amplifier station, Models 751-901 with enclosures 733-001 or 7335-005: (i) Smart handset/speaker amplifier station, Model 751-901 – Similar to presently CSA accepted smart handset/speaker amplifier model 751-801 which is presently CSA certified under report 159658-2500004743. The only difference between 751-901 and 751-801 is that model 751-901 uses different PC board construction and has a AC hum shield. Model 751-901 has been evaluated to CSA standards for use in Cl. I, Div. 2, Gps. A, B, C and D by UL under UL report E98383, Refer to copy of UL report attached to this report for complete description. (ii) Enclosure, Model 733-001 and 7335-005 – These enclosures are presently CSA accepted to be used with handset/speaker amplifier model 701-802 and –804 under report 159658-2500004743. Refer to CSA report 159658-2500004743 for complete description. Part C - Smart series remote handset/speaker amplifier station, Model 723-801 with desk top five party remote subset model A02027 and enclosure 7245-004. (i) Smart series remote handset/speaker amplifier station, Model 723-801 - This remote handset/speaker amplifier station is presently CSA accepted to be used with desk top five party remote subset model 7265-101 and enclosure model 7245-004 under report 159658-2500003511. Refer to CSA report 159658-2500003511 for complete description. (ii) Enclosure, Model 7245-004 – This enclosure is presently CSA accepted to be used as described in item (i) above, refer to CSA report 159658-2500003511 for complete description. (iii) Desk Top Five Party Remote Subset, Model A02027 - Similar to presently CSA accepted desk top five party remote subset model 7265-101 which is presently CSA certified under report 159658-2500003511. The only difference between A02027 and 7265-101 is that model A02027 has an additional spst momentary push button switch across the AUX0 input and between ground so that when the switch is engaged the switch grounds the AUX0 input. As a result of this switch the amplifier is programmed to have an alternative page destination when the push button is depressed. Refer to the following drawings for further information A51016-001, A02027C03, 71967(Sheet 1 of 3), A02027B01 and A02027D02. F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Page No: 5 Date Issued: September 24, 2002 Descriptive Documents: Subject Drawing No. Rev. Date U.L. Report (Vol. 1) E98383 - Switch, Pushbutton-Momentary, SPST Normally open (P/N 51016-001) A51016-001 - 5-21-96 (Issued) 8-15-00 (Revised) 10/23/84 No. A02027A Flush Mount Panel Sunset Connection Diagram A02027C03 - 5/21/02 71967 D 12/02/96 A02027B01 - 5/21/02 A02027D02 - 5/21/02 Smart Station Base-16 PC Board Assembly Schematic No. 69241-002 No. A02027 Flush Mount Smart Station Outline No. A02027A Flush Mount Panel Subset Outline F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc MASTER CONTRACT: 159658 REPORT: 1361537 PROJECT: 1361537 Page No: 6 Date Issued: September 24, 2002 TEST REPORT No testing was deemed necessary since all (except A02027) components are either CSA or ULC certified for use in Cl. I, Div. 2 area. No testing for the A02027 was deemed necessary since A02027 is similar to presently CSA accepted desk top five party remote subset model 7265-101 except for an addition of a pushbutton. This pushbutton switch was deemed non-incendive based on the circuit being resistive in nature with a Voc= 5 Vdc and Isc = 0.5 mA. F:\Standard IOMs - Current Release\Publication Administration\Documents\Approvals for Intranet\CSA\1361537.doc
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 29 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:8dea3656-7cb7-430e-aa59-0f0574d553a5 Creation Date--Text : Wednesday, April 23, 2003 3:26:25 PM Keywords : Producer : Acrobat PDFWriter 3.02 for Windows Modify Date : 2004:08:23 09:48:55-04:00 Creator Tool : Print CSA 2 Metadata Date : 2004:08:23 09:48:55-04:00 Document ID : uuid:8ca52864-10e6-4062-bb5a-df4f973ef66c Format : application/pdf Title : CSA Creator : GAI-Tronics Description : Create Date : Wednesday, April 23, 2003 3:26:25 PM Author : GAI-Tronics Subject :EXIF Metadata provided by EXIF.tools