Cat 924G Install 924
User Manual: Cat 924 Install
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Catapillar 924 Loadlog 800/8000 Installation Supplement Fittings Required: 609030 1” Orfice Fitting (Qty. 2) This supplement will show some of the locations for mounting the equipment included in this scale system. The installations shown are not required locations they are only intended as a guide. Head Unit Mounting The head unit was mounted to the right-hand post using the rops bracket supplied in the kit. Route the Head Unit cable to the right hand electrical box. The cable will be plugged into the Junction Box. Catapillar 924 Loadlog 800/8000 Installation Supplement Load Sensor Installation This installation is made by using the 1” Orfice Fitting supplied in the kit. The location is at the end of the hoses from the lift cylinder Left or Right side of machine. Load Sensor Mounting The sensor mount is to the plate close to the tee fittings using the brackets supplied by drilling a hole or using an existing stud or bracket. Use the extention cable to route wire to right hand electrical compartment of cab. Cover the wires with supplied tubing through/over articulation point!! Catapillar 924 Loadlog 800/8000 Installation Supplement Dual Clamp Assembly Use the Dual Sensor Mounting Bracket as shown to secure sensors to the machine. Reference/Direction Sensor The Ref/Dir sensor mounting bracket location for this installation is within 200mm of the pivot point. The Bracket is bolted to the plate by drilling two holes. The magnet was mounter using the bracket supplied Be sure to provide clearance for the loader arm. Route cable to right hand electrical compartment of cab. Cover wire with tubing through the articulatinion point. Catapillar 924 Loadlog 800/8000 Installation Supplement Juncton Box Mounting The typical location for the junction box is the right or left side of the machine behind the removable front cover. (Image is for location purpose only). The Junction Box may be secured to surrounding cables. Remote Enter Switch The remote enter switch needs to be mounted to allow easy access by the operator. Route cable to the right hand electrical panel to be connected to terminal in J-Box. Loadlog 800/8000 Installation Supplement Wiring and Connections The gray head unit cable and the black link cable are taken out of the cab in the location shown and routed to the J-box. This is also the area where the kickout solenoid can be found. The Power cable, Kickout cable and the Remote enter switch are all connected to the black link cable. This location is under the Right hand trim panel. Wiring and Connections The cables once routed out of the cab will be routed through the center of the machine and to the junction box. Use the black loom to cover the cables to help prevent premature failure. Use caution when routing cables through the center piviot of the machine. Catapillar 924 Loadlog 800/8000 Installation Supplement Power Connection The power connection can be made at the location shown its switched 24v. Be sure the Master Disconnect is in the off position before removing the nut on the bottom on the fuse box. Ground Connection The ground connection can be made in this location make sure the connection is clean to provide a good connection. Catapillar 924 Loadlog 800/8000 Installation Supplement Kickout Connection The kickout connection if desired is made in this location below the control levers. Find the wire that has +volts when the lift lever is engaged then follow the instruction in the manual. Kickout Connection The kickout relay wiring will connect into the Black link cable with the remote enter switch and the power connection. Kickout Relay Installed Loadlog 800/8000 Installation Supplement Wiring-Power Connections The Power and Ground connections can be made by removing the right hand side panel. The scale system is able to use 12v or 24v if 12v is used to power the scale the jumper in the J-Box must be changed to the 12v setting. If a printer is being installed it will need to be connected to power in the same location. Optional Equipment If other optional equipment is to be installed such as a Printer or Telemetry radios you will need to plan for mounting this equipment as well. The printer cable is a split cable one end runs to the head unit one end to a power connection and the other end to the printer. Plan ahead when routing the gray head unit cable and the power cable and route the cable for the printer at the same time. The data radio for the telemetry will be powered by the connection at the head unit no external power is required but the radio will need to be mounted and the cable run to the head unit. The antenna for the radio will need to be routed outside the cab. Loup Electronics Inc. 2960 North 38th Street Lincoln, NE. 68504 Phone: 402-464-7131 Fax: 402-464-7104 Toll Free: 877-489-5687
Source Exif Data:
File Type : AI File Type Extension : ai MIME Type : application/vnd.adobe.illustrator PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.1-c036 46.277092, Fri Feb 23 2007 14:17:08 Modify Date : 2010:04:08 16:23:22-05:00 Create Date : 2005:10:19 08:46:20-05:00 Metadata Date : 2010:04:08 16:23:22-05:00 Creator Tool : Adobe Illustrator CS3 Thumbnail Width : 204 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 17912 bytes, use -b option to extract) Document ID : uuid:66c31c6c-9d7e-4b69-8a7f-f173e3449c16 Instance ID : uuid:9f724d62-820f-4626-a06d-b214731ccf71 Format : application/pdf N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 612.000000 Max Page Size H : 792.000000 Max Page Size Unit : Pixels Font Name : Myriad-Bold, Myriad-Roman Font Family : Myriad, Myriad Font Face : Bold, Roman Font Type : Type 1, Type 1 Font Version : 001.000, 001.000 Font Composite : False, False Font File Name : wmb_____.pfb; wmb_____.pfm, wmr_____.pfb; wmr_____.pfm Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Page Count : 8 Creator : Adobe Illustrator(R) 13.0 For : Jeremiah, Title : Cat 924G Install.pdf Bounding Box : 17 23 595 755 Container Version : 11 Creator Version : 13 Image Height : 732 Image Width : 578 Image Size : 578x732 Megapixels : 0.423EXIF Metadata provided by EXIF.tools