Codan Radio HF Commercial Catalogue 2015
User Manual: Catalogues | LMR & HF Radio | Codan Radio
Open the PDF directly: View PDF 
.
Page Count: 220
| Download | |
| Open PDF In Browser | View PDF |
This is Issue 8 of the HF Codan Radio Communications Commercial Product Catalogue, January 2015. No part of this product catalogue may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Limited. Pictures shown in this product catalogue are for illustration purposes only — actual products, colours and configurations may vary from the pictures shown. The products in this catalogue are available with the NGT™ series Transceivers and / or the Envoy™ series Transceivers as indicated by the following logos. A compatibility statement specifies the transceiver models that are applicable. NGT TRANSCEIVER Available with the NGT™ series Transceivers Available with Envoy™ series Transceivers CODAN™, Envoy™, NGT™, Easitalk™, CALM™ and Crosspatch™ are trademarks of Codan Limited. Other brand, product and company names mentioned in this document are trademarks or registered trademarks of their respective holders. © Copyright 2015 Codan Limited. Envoy™ X1 Configurations ................................................................................................................................... 1 Envoy™ X1 Transceiver ........................................................................................................................................ 1 Envoy™ X1 Mobile ................................................................................................................................................. 2 Envoy™ X1 Base ...................................................................................................................................................... 3 Envoy™ X1 Options ............................................................................................................................................... 4 Envoy™ X2 Configurations ................................................................................................................................... 7 Envoy™ X2 Transceiver......................................................................................................................................... 7 Envoy™ X2 Mobile ................................................................................................................................................. 8 Envoy™ X2 Base ...................................................................................................................................................... 9 Envoy™ X2 Options ............................................................................................................................................ 10 Envoy™ X1 Configurations for Australia.........................................................................................................15 Envoy™ X1 Transceiver...................................................................................................................................... 15 Envoy™ X1 Packages .......................................................................................................................................... 16 Envoy™ X2 Configurations for Australia.........................................................................................................17 Envoy™ X2 Transceiver...................................................................................................................................... 17 Envoy™ X2 Packages .......................................................................................................................................... 18 NGT™ SR Configurations.....................................................................................................................................19 NGT™ SR Transceiver ......................................................................................................................................... 19 NGT™ SR Mobile .................................................................................................................................................. 20 NGT™ SR Base....................................................................................................................................................... 21 NGT™ SR Options ................................................................................................................................................ 22 NGT™ ASR Configurations ..................................................................................................................................25 NGT™ ASR Transceiver ...................................................................................................................................... 25 NGT™ ASR Mobile ............................................................................................................................................... 26 NGT™ ASR Base.................................................................................................................................................... 27 NGT™ ASR Options ............................................................................................................................................. 28 NGT™ SRx Configurations...................................................................................................................................31 NGT™ SRx Transceiver....................................................................................................................................... 31 NGT™ SRx Mobile ............................................................................................................................................... 32 NGT™ SRx Base .................................................................................................................................................... 33 NGT™ SRx Options.............................................................................................................................................. 34 NGT™ AR Configurations for Australia............................................................................................................37 NGT™ AR Transceiver......................................................................................................................................... 37 NGT™ AR Packages ............................................................................................................................................. 38 NGT™ AR Options ............................................................................................................................................... 39 NGT™ SRx Configurations for Australia ..........................................................................................................41 NGT™ SRx Transciever....................................................................................................................................... 41 NGT™ SRx Packages ........................................................................................................................................... 42 NGT™ SRx Options.............................................................................................................................................. 43 HF Radio Communications International Product Catalogue Issue 8 January 2015 Page I Transceiver Accessories ...................................................................................................................................... 45 Transceiver Accessories .................................................................................................................................... 45 Base Accessories.................................................................................................................................................. 53 Data & Email ......................................................................................................................................................... 59 RC50-C HF Email Software .............................................................................................................................. 59 RC50-C Cable Options ....................................................................................................................................... 60 UUPlus™ Server Software................................................................................................................................. 61 UUPlus™ Server Cable Option......................................................................................................................... 62 UUPlus™ Client Software ................................................................................................................................. 63 UUPlus™ Client Cable Options....................................................................................................................... 64 RM50e HF Data Modem ................................................................................................................................... 65 3012 HF Data Modem(No cables)................................................................................................................. 67 3012 HF Data Modem for NGT™ with 2 M RS232 cable ....................................................................... 68 3012 HF Data Modem for NGT™ with 6 M RS232 cable ....................................................................... 69 3012 Accessories................................................................................................................................................. 70 3212 HF Data Modem (No cables)................................................................................................................ 71 3212 HF Data Modem for NGT™/Envoy X2 with 2 M RS232 cable ................................................... 72 3212 HF Data Modem for NGT™/Envoy™ X2 with 6 M RS232 cable ................................................ 73 3212 Accessories................................................................................................................................................. 74 High Power Amplifiers........................................................................................................................................ 75 3061 500 W Power Amplifier.......................................................................................................................... 75 3061 Accessories................................................................................................................................................. 76 3062 1 kW Power Amplifier ............................................................................................................................ 77 3062 Accessories................................................................................................................................................. 78 Crosspatch™/Phone/GPS Solutions ................................................................................................................ 79 Crosspatch™ for NGT™/Envoy™ .................................................................................................................... 79 Crosspatch™ Accessories.................................................................................................................................. 79 3033 Telephone Interconnect ........................................................................................................................ 80 3033 Accessories................................................................................................................................................. 81 GPS Tracking Software...................................................................................................................................... 82 GPS Accessories ................................................................................................................................................... 82 Transceiver Supplies............................................................................................................................................ 83 3020 Transceiver Supply .................................................................................................................................. 83 3020 Accessories................................................................................................................................................. 84 DC-DC Voltage Converter ................................................................................................................................ 84 Solar Power Supplies ......................................................................................................................................... 85 Solar Power Supplies Accessories.................................................................................................................. 85 Batteries................................................................................................................................................................. 86 Antennas ................................................................................................................................................................ 87 3040 Automatic Tuning Whip with 6 M Cables....................................................................................... 88 3040 Accessories................................................................................................................................................. 89 9350 Automatic Tuning Whip........................................................................................................................ 90 Page II HF Radio Communications International Product Catalogue Issue 8 January 2015 9350 Automatic Tuning Whip with 6 M Cables....................................................................................... 91 9350 Accessories................................................................................................................................................. 92 3042 HF Antenna Tuner ................................................................................................................................... 93 3042 HF Antenna Tuner with 6 M Cables .................................................................................................. 94 Antennas.................................................................................................................................................................95 3042 Accessories................................................................................................................................................ 95 Tuners ..................................................................................................................................................................... 97 Tuner Accessories ............................................................................................................................................... 97 Base Whip.............................................................................................................................................................. 98 Base Whip Accessories..................................................................................................................................... 98 Tuned Long Wire................................................................................................................................................. 99 3048 Tuned Dipole...........................................................................................................................................100 Travelling Wave Dipole...................................................................................................................................101 Delta......................................................................................................................................................................102 Semi-Delta ..........................................................................................................................................................103 TFD411 Broadband ..........................................................................................................................................104 TFD411 Broadband/Masts Kits....................................................................................................................106 Antenna Masts ..................................................................................................................................................107 Masts, Guyed 10 M ..........................................................................................................................................108 Coaxial Cables Type RG58 .............................................................................................................................109 Coaxial Cables Type RG213...........................................................................................................................109 Lightning Protection ........................................................................................................................................110 Antennas for Australia ..................................................................................................................................... 112 3040 Automatic Tuning Whip Standard Package .................................................................................112 3040 Automatic Tuning Whip Explorer Package...................................................................................113 9350 Automatic Tuning Whip Standard Package .................................................................................114 9350 Automatic Tuning Whip Venturer Package..................................................................................115 Remote Control .................................................................................................................................................. 117 Envoy™ Remote Control Accessories — Ethernet .................................................................................117 NGT™ Remote Control Equipment—2-Wire...........................................................................................118 NGT™ Remote Control Accessories ............................................................................................................119 NGT™ Split-Site Equipment — 2-wire .......................................................................................................120 NGT™ Split-Site Equipment —4-wire ........................................................................................................122 Split-site Accessories .......................................................................................................................................124 19" Racks & Accessories ................................................................................................................................... 125 Standard Rack Configurations ....................................................................................................................125 19" Rack Cabinets .............................................................................................................................................127 19" Rack Mount System Trays .....................................................................................................................127 19" Rack Mount Blanking Panels.................................................................................................................128 19" Rack Mount Accessories ........................................................................................................................128 HF Radio Communications International Product Catalogue Issue 8 January 2015 Page III 2110 Transceiver Configurations...................................................................................................................129 2110 Series Transceiver Kit............................................................................................................................129 2110 Series Patrol Configuration ................................................................................................................130 2110 Series Explorer Configuration ...........................................................................................................131 2110 Series Homeland Security Configuration ......................................................................................133 2110 Transceiver ................................................................................................................................................135 2110 Transceiver Units ...................................................................................................................................135 2110 Options......................................................................................................................................................136 2110 Accessories...............................................................................................................................................139 Data & Email for 2110 ......................................................................................................................................143 RC50-C HF Email Software ............................................................................................................................143 UUPLUS™ Software ..........................................................................................................................................144 3012 HF Data Modem (No cables)..............................................................................................................146 3012 HF Data modem for 2110 with 6 M RS232 Cable.......................................................................147 3012 Accessories...............................................................................................................................................148 3212 HF Data Modem (No cables)..............................................................................................................149 3212 HF Data Modem for 2110 with 2 M RS232 Cable.......................................................................150 3212 HF Data Modem for 2110 with 6 M RS232 Cable.......................................................................151 3212 Accessories...............................................................................................................................................152 Crosspatch™ for 2110 .......................................................................................................................................153 Crosspatch™ for 2110 .....................................................................................................................................153 Crosspatch™ Accessories................................................................................................................................153 Antenna Accessories .........................................................................................................................................155 Long Wire and Dipoles ....................................................................................................................................155 Tactical Masts ....................................................................................................................................................156 Whip Antennas..................................................................................................................................................156 Cables....................................................................................................................................................................156 Earthing................................................................................................................................................................157 Battery & Charger Accessories .......................................................................................................................159 Batteries...............................................................................................................................................................159 DC-DC Voltage Converter ..............................................................................................................................159 Chargers...............................................................................................................................................................160 Charger Modules...............................................................................................................................................160 Charger Output Cables ...................................................................................................................................161 Charger Input Cables AC ................................................................................................................................162 Charger Input Cables DC ................................................................................................................................162 Backpacks.............................................................................................................................................................163 Backpacks ............................................................................................................................................................163 Backpack & Mounting Accessories................................................................................................................164 Mounting Accessories .....................................................................................................................................164 Page IV HF Radio Communications International Product Catalogue Issue 8 January 2015 Language Support .....................................................................................................................................................165 English Manuals................................................................................................................................................165 French Manuals.................................................................................................................................................168 Spanish Manuals ..............................................................................................................................................169 Arabic Manuals..................................................................................................................................................170 Dari Manuals......................................................................................................................................................170 Portuguese Manuals........................................................................................................................................170 Russian Manuals...............................................................................................................................................170 Shipping Weights .............................................................................................................................................. 171 Shipping Weights .............................................................................................................................................171 Standard Packing Dimensions........................................................................................................................ 184 Standard Packing Dimensions .....................................................................................................................184 Standard Terms & Conditions of Supply ..................................................................................................... 186 Standard Terms & Conditions of Supply ...........................................................................................................186 International Product Warranty provided by Codan................................................................................ 195 International Product Warranty provided by Codan.....................................................................................195 2240 SmartLink Accessory Addendum ................................................................................................................. 197 2240 SmartLink Accessory Addendum ..............................................................................................................197 HF Radio Communications International Product Catalogue Issue 8 January 2015 Page V 2240 SmartLink Accessory Addendum Please note that from pages 197 to 206 an addendum is included to cover details on the Envoy SmartLink. Page VI HF Radio Communications International Product Catalogue Issue 8 January 2015 Envoy™ X1 Configurations ENVOY™ X1 TRANSCEIVER PRODUCT ENVOY-X1-TCVR Envoy X1 Transceiver PART NO. Envoy Transceiver DESCRIPTION Envoy™ X1 Transceiver The Envoy™ X1 Transceiver is a state-of- the-art software defined HF transceiver that delivers high performance but cost-effective voice communications for both base and mobile applications. The X1 Transceiver can be used with the 2221 or 2220 Handset or 2230 Desk Console. Both handset types and the desk console incorporate the new large format colour display and intuitive icon based menu system providing ease of use and programming. NOTE: The GPIO connector on the Envoy™ X1 Transceiver does not support any peripherals apart from a Morse Code Key. The standard transceiver consists of the parts listed below. The following pages detail the parts required for Envoy™ X1 Mobile and Base configurations. COMPRISING: 08-07218-001 08-07000-001 15-00149 15-00649 08-06022-001 30-11208-000 15-04177-## 06-02809-EN • • • • • • • EnvoyTM X1 2210 RF Unit EnvoyTM 2220 Handset EnvoyTM 2220 Handset Cradle External Speaker with 4 m Lead Envoy™/NGT™ Handset Control Cable, 6 m Self Adhesive Rubber Feet (x4) EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card STANDARD FEATURES: • • • • • • • 100 channels, 1.6 to 30 MHz, 10 scan groups 200 Contact List entries Simultaneous scanning of multiple scan groups 125 W PEP, 12 V DC, USB/LSB/AM Ethernet/USB connectivity English language graphical user interface Codan Selcall (including Diagnostic, Phone and Emergency Call types) • GPS receiver port • In-built EasitalkTM speech noise reduction • MIL-STD-810G for Drop, Dust, Shock, Vibration AVAILABLE OPTIONS & ACCESSORIES: See pages 4 and 45 for Envoy™ X1 Options and Transceiver Accessories. ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 1 Envoy™ X1 Configurations ENVOY™ X1 MOBILE PRODUCT Envoy X1 Mobile PART NO. ENVOY-X1-MOB DESCRIPTION Envoy™ X1 Mobile Configuration The Envoy™ X1 Mobile Configuration consists of an Envoy™ Transceiver, a 3040 Automatic Tuning Whip Antenna and cables, and vehicle installation hardware kit. COMPRISING: 08-07218-001 08-07000-001 15-00149 15-00649 08-06022-001 15-04177-## 06-02809-EN Envoy™ X1 Transceiver • EnvoyTM X1 2210 RF Unit • EnvoyTM 2220 Handset • EnvoyTM 2220 Handset Cradle • External Speaker with 4 m Lead • Envoy™/NGT™ Handset Control Cable, 6 m • EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card 3040 Automatic Tuning Whip with 6 m Cables The 3040 consists of the following parts. See page 89 for additional 3040 accessories. 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit 15-00130 RF Unit Cradle & Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. 15-00112 Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. AVAILABLE OPTIONS & ACCESSORIES: See pages 4 and 51 for Envoy™ X1 Options and Mobile Accessories. ## denotes language version Page 2 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X1 Configurations ENVOY™ X1 BASE PRODUCT Envoy X1 Base PART NO. ENVOY-X1-BASE DESCRIPTION Envoy™ X1 Base Station Configuration The Envoy™ X1 Base Station Configuration consists of an Envoy™ X1 Transceiver, a 2230 Desk Console, a TFD411 Antenna, 3020 Heavy Duty Transceiver Supply, and cables. COMPRISING: 08-07218-001 08-07204-001 15-60025 08-07205-006 30-11208-000 15-04177-## 06-02809-EN 15-00411-004 Envoy™ Transceiver • EnvoyTM X1 2210 RF Unit • EnvoyTM 2230 Desk Console • 2230 Desk Console Boom Microphone • Envoy™ Console to RF Unit Cable, 6 m • Self Adhesive Rubber Feet (x4) • EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card TFD411 Antenna 125 W, 2–30 MHz, 34 m The antenna can be mounted horizontally between two support systems, or as an inverted “V” using a single central support mast. NOTE: Mast is not included. For masts, see page 107, Antenna Masts. 08-01503-030 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 30 m of high quality RG58 coaxial cable terminated with waterproof UHF style connectors. 78-20022 3020 Transceiver Supply Power supply to convert AC Mains into 13.8 V DC to power the X1 Transceiver. 67-9030# Power IEC Cable, 2 m Used to connect 3020 Transceiver Supply to AC Mains source. For cable options, see page 83, 3020 Transceiver Supply. 05-06374 Earth Braid, 1.5 m Used to connect X1 RF Unit to ground point. AVAILABLE OPTIONS & ACCESSORIES: See pages 4 and 53 for Envoy™ X1 Options and Base Accessories. # denotes the cable variant depending upon country of use ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 3 Envoy™ X1 Configurations ENVOY™ X1 OPTIONS Envoy X1 Options PRODUCT PART NO. DESCRIPTION 15-10560 Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Standard call types include: Selective Call, All Call, Phone Call, Message Call, Diagnostic Call, Emergency Call. 15-10558 Opt, Default Open Selcall 15-10561 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). Envoy X1 Options NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option. For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. 15-10518 Opt Amateur Mode Enables transmit within designated HF Amateur frequency bands when using the Free Tune Receiver mode. 15-10599 Opt Dari Language Enables Dari Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10600 Opt Russian Language Enables Russian Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10580 Opt Spanish Language Enables Spanish Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10601 Opt French Language Enables French Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10513 Opt 100 W Sets maximum transmit power to 100 watts. Continued on the next page Page 4 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X1 Configurations ENVOY™ X1 OPTIONS cont. Envoy X1 Options PRODUCT PART NO. DESCRIPTION 15-10481 Opt TxD, Tx Program Disabled Disables keypad programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. 15-10491 Opt TxP, Tx Program Prohibited Prohibits keypad programming of new transmit and receive frequencies. 15-10582 Opt 500 Hz Filter 500 Hz filter software filter for narrow band operation e.g. Morse Code. 15-10563 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. 15-10591-000 Opt Digital Voice (Factory Fit) Enables digital voice capability. Digital voice provides highly intelligible audio, free from background noise, interference, and fading effects often experienced with analogue voice. Envoy X1 Options Supplied standard with MELPe and TWELP vocoder types and 2400bps data rate as standard. AES-256 Encryption (part number 15-10595) and 1200bps and 600bps vocoder rate options (part numbers 15-10596 & 15-10597) may be added for additional capability. NOTE: • AES-256 Encryption option (15-10595) can be added. • 1200 bps and Low rate Vocoder (15-10596, 15-10597) can be added • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. • This option is also available as a retro fit kit (part number 15-10591). 15-10596 Opt 1200 bps Vocoder Strongly recommended optional 1200 bps vocoder data rate for Digital Voice option (part number 15-10591-000), enabling digital voice to operate in highly degraded channel conditions. 15-10597 Opt Low rate Vocoder Optional 600 bps vocoder data rate for Digital Voice option (part number 15-10591-000), enabling digital voice to operate in highly degraded channel conditions. Envoy X1 Options Envoy X1 Options Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 5 Envoy™ X1 Configurations ENVOY™ X1 OPTIONS cont. Envoy X1 Options PRODUCT PART NO. 15-10595 Envoy X1 Options DESCRIPTION Opt AES-256 Encryption Adds AES-256 Encryption, with support for up to 256 preloaded keys. Suitable for use in conjunction with the MILSTANAG 2G Data and Digital Voice options (part numbers 1510591, 15-10589, 15-10590). NOTE: • KMS/KFS Key Fill Software recommended (see page 48, Key Management Software). 15-10564-000 Opt CES-128 Encryptor Module (Factory Fit) High grade Voice Encryptor Module that provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10564). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10582 Page 6 Opt 500 Hz Filter 500 Hz filter software filter for narrow band operation e.g. Morse Code. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X2 Configurations ENVOY™ X2 TRANSCEIVER PRODUCT Envoy X2 Transceiver PART NO. ENVOY-X2-TCVR DESCRIPTION Envoy™ X2 Transceiver The Envoy™ X2 Transceiver is a state-of-the-art software defined HF transceiver delivering high performance voice and data communications and systems capabilities for both base and mobile applications. The X2 Transceiver can be used with the 2221 or 2220 Handset or 2230 Desk Console. Both handset types and the desk console incorporate the new large format colour display and intuitive icon based menu system providing ease of use and programming. Envoy X2 Transceiver The standard transceiver consists of the parts listed below. The following pages detail the parts required for Envoy™ X2 Mobile and Base configurations. COMPRISING: 08-07218-002 08-07000-001 15-00149 15-00649 08-06022-001 30-11208-000 15-04177-## 06-02809-EN • • • • • • • EnvoyTM X2 2210 RF Unit EnvoyTM 2220 Handset EnvoyTM 2220 Handset Cradle External Speaker with 4 m Lead Envoy™/NGT™ Handset Control Cable, 6 m Self Adhesive Rubber Feet (x4) EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card STANDARD FEATURES: • • • • • • • • • • • 1000 channels, 1.6 to 30 MHz, 20 scan groups 500 Contact List entries Simultaneous scanning of multiple scan groups 125 W PEP, 12 V DC, USB/LSB/AM Ethernet/USB connectivity 15-way general purpose interface port (GPIO) for systems and accessory connectivity English language graphical user interface Codan Selcall (including Diagnostic, Phone and Emergency Call types) GPS receiver port In-built EasitalkTM speech noise reduction MIL-STD-810G for Drop, Dust, Shock, Vibration AVAILABLE OPTIONS & ACCESSORIES: See pages 10 and 45 for Envoy X2 Options and Transceiver Accessories. ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 7 Envoy™ X2 Configurations ENVOY™ X2 MOBILE Envoy X2 Mobile PRODUCT PART NO. ENVOY-X2-MOB DESCRIPTION Envoy™ X2 Mobile Configuration The Envoy™ X2 Mobile Configuration consists of an Envoy™ Transceiver, a 3040 Automatic Tuning Whip Antenna and cables, and vehicle installation hardware kit. COMPRISING: 08-07218-002 08-07000-001 15-00149 15-00649 08-06022-001 15-04177-## 06-02809-EN Envoy™ X2 Transceiver • EnvoyTM X2 2210 RF Unit • EnvoyTM 2220 Handset • EnvoyTM 2220 Handset Cradle • External Speaker with 4 m Lead • Envoy™/NGT™ Handset Control Cable, 6 m • EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card 3040 Automatic Tuning Whip with 6 m Cables The 3040 consists of the following parts. See page 89 for additional 3040 accessories. 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit 15-00130 NGT™/Envoy™ RF Cradle & Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. 15-00112 Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. AVAILABLE OPTIONS & ACCESSORIES: See pages 10 and 51 for Envoy X2 Options and Mobile Accessories. Page 8 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X2 Configurations ENVOY™ X2 BASE Envoy X2 Base PRODUCT PART NO. ENVOY-X2-BASE DESCRIPTION Envoy™ X2 Base Station Configuration The Envoy™ Base Station Configuration consists of an Envoy™ Transceiver, a TFD411 Antenna, 3020 Heavy Duty Transceiver Supply, and cables. COMPRISING: 08-07218-002 08-07204-001 15-60025 08-07205-006 30-11208-000 15-04177-## 06-02809-EN 15-00411-004 Envoy™ X2 Transceiver • EnvoyTM X2 2210 RF Unit • EnvoyTM 2230 Desk Console • 2230 Desk Console Boom Microphone • Envoy™ Console to RF Unit Cable, 6 m • Self Adhesive Rubber Feet (x4) • EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card TFD411 Antenna 125 W, 2–30 MHz, 34 m The antenna can be mounted horizontally between two support systems, or as an inverted “V” using a single central support mast. NOTE: Mast is not included. For masts, see page 107, Antenna Masts. 08-01503-030 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 30 m of high quality RG58 coaxial cable terminated with waterproof UHF style connectors. 78-20022 3020 Transceiver Supply Power supply to convert AC Mains into 13.8 V DC to power the X2 Transceiver. 67-9030# Power IEC Cable, 2 m Used to connect 3020 Transceiver Supply to AC Mains source. For cable options, see page 83, 3020 Transceiver Supply. 05-06374 Earth Braid, 1.5 m Used to connect X2 RF Unit to ground point. AVAILABLE OPTIONS & ACCESSORIES: See pages 10 and 53 for Envoy X2 Options and Base Accessories. # denotes the cable variant depending upon country of use ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 9 Envoy™ X2 Configurations ENVOY™ X2 OPTIONS Envoy X2 Options PRODUCT PART NO. DESCRIPTION 15-10560 Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Standard call types include: Selective Call, All Call, Phone Call, Message Call, Diagnostic Call, Emergency Call. 15-10568 Opt MIL-STD-188-141B ALE Full This option provides full MIL-STD-188-141B ALE capability, including all capabilities provided by the FED-STD-1045 (part number 15-10560) option above. Envoy X2 Options Additional call types include, NET Call, ANY Call, Group Call, Wildcard Call, in-link AMD Message Calls, as well as an advanced ALE beacon and Last Heard station log. 15-10569 Opt MIL-STD-188-141B Upgrade This option is used to order a factory password to field upgrade an Envoy Transceiver that already has FED-STD-1045 ALE/CALM™ enabled but requires MIL-STD-188-141B capability. NOTE: This part should only be used for ordering field upgrade passwords. 15-10558 Opt, Default Open Selcall 15-10561 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option.For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. 15-10559 Opt 2400 bps Internal Data Modem Enables the embedded software modem providing robust error free point to point data communications. Supports simple AT command interface or full feature HF Email/Chat applications, see page 59, Data & Email for more details. Recommend to include Option Fan (part number 15-10469000) 15-10518 Opt Amateur Mode Enables transmit within designated HF Amateur frequency bands when using the Free Tune Receiver mode. 15-10599 Opt Dari Language Enables Dari Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. Continued on the next page Page 10 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X2 Configurations ENVOY™ X2 OPTIONS Envoy X2 Options PRODUCT PART NO. DESCRIPTION 15-10600 Opt Russian Language Enables Russian Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10580 Opt Spanish Language Enables Spanish Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10601 Opt French Language Enables French Language user interface as a user selectable option for any control point (2221/2220 Handset or 2230 Desktop Console) connected to the RF Unit. 15-10513 Opt 100 W Sets maximum transmit power to 100 watts. 15-10481 Opt TxD, Tx Program Disabled Disables keypad programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. 15-10491 Opt TxP, Tx Program Prohibited Prohibits keypad programming of new transmit and receive frequencies. 15-10582 Opt 500 Hz Filter 500 Hz filter software filter for narrow band operation e.g. Morse Code. 15-10562 Opt 2.7 kHz Filter 2.7 kHz wideband software filter. Recommended for use with 2G data and Digital Voice options (15-10589-000, 15-10590000, 15-105491-000) and RM50e external data modem. 15-10583 Opt 3 kHz Filter 3 kHz wideband software filter. 15-10563 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 11 Envoy™ X2 Configurations ENVOY™ X2 OPTIONS cont. Envoy X2 Options PRODUCT PART NO. 15-10589-000 DESCRIPTION Opt MIL-STANAG 2G Data (Factory Fit) Enables integrated data modem capability according to MILSTD-110-188A/B and STANAG 4539. This provides a range of military spec data waveforms from 75 to 9600 bps uncompressed, capable of operating across varying channel conditions. The modem utilises adaptive equalisation and turbo-decoding for maximum performance. Provides efficient email over HF when used in conjunction with RC50-C email gateway (part number 15-04161-CD), see page 58, “RC50-C HF Email Software”. NOTE: • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. • 2.7 kHz filter (15-10562) is recommended for optimum data performance. • AES-256 Encryption option (15-10595) can be added. • Retro Kit: 15-10589. 15-10590-000 Opt MIL-STANAG 2G Data and Digital Voice (Factory Fit) Integrates the MIL/STANAG 2G Data and Digital Voice options. Requires RC50-C email gateway (part number 1504161-CD) for data operation, see page 58, “RC50-C HF Email Software”. NOTE: • AES-256 Encryption option (15-10595) can be added. • 1200 bps and Low rate Vocoder (15-10596, 15-10597) can be added. • 2.7 kHz filter (15-10562) is recommended for optimum data and digital voice performance. • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. • Retro Kit: 15-10590. 15-10598 Opt ISB Enables Independent Sideband operation when used in conjunction with 2G data options (15-10589-000 and 1510590-000) and RC50-C HF Email Software. Provides data rates of up 19200 bps. NOTE: • On air compatible with ISB data option in the NGT SRx transceiver, see page 35 Continued on the next page Page 12 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X2 Configurations ENVOY™ X2 OPTIONS cont. Envoy X2 Options PRODUCT PART NO. 15-10591-000 Envoy X1 Options DESCRIPTION Opt Digital Voice (Factory Fit) Enables digital voice capability. Digital voice provides highly intelligible audio, free from background noise, interference, and fading effects often experienced with analogue voice. Supplied standard with MELPe and TWELP vocoder types and 2400 bps data rate as standard. NOTE: • AES-256 Encryption option (15-10595) can be added. • 1200 bps and Low rate Vocoder (15-10596, 15-10597) can be added. • 2.7 kHz filter (15-10562) is recommended for optimum digital voice performance. • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. • This option is also available as a retro fit kit (part number 15-10591). 15-10596 Opt 1200 bps Vocoder Strongly recommended optional 1200 bps vocoder data rate for Digital Voice option (part number 15-10590-000 or 1510591-000), enabling digital voice to operate in highly degraded channel conditions. 15-10597 Opt Low rate Vocoder Optional 600 bps vocoder data rate for Digital Voice option (part number 15-10590-000 or 15-10591-000), enabling digital voice to operate in highly degraded channel conditions. 15-10595 Opt AES-256 Encryption Adds AES-256 Encryption, with support for up to 256 preloaded keys. Suitable for use in conjunction with the MILSTANAG 2G Data and Digital Voice options (part numbers 1510591, 15-10589, 15-10590). Envoy X1 Options Envoy X1 Options Envoy X1 Options NOTE: • KMS/KFS Key Fill Software recommended (see page 48, Key Management Software). Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 13 Envoy™ X2 Configurations 15-10564-000 Opt CES-128 Encryptor Module (Factory Fit) High grade Voice Encryptor Module that provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10564). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for Envoy™/NGT™ series Transceivers. NOTE: This option is also available as a retro fit kit (part number 15-10469). Digital Voice and 2G Data Upgrade Selection Matrix Upgrade Capabilities 2G Data and DV Options 15-10591-000 (DV) 15-10590-000 (2G Data & DV) 15-10589-000 (2G Data) Page 14 1200 bps Vocoder data rate (15-10596) Low rate Vocoder (15-10597) AES-256 Encryption (15-10595) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X1 Configurations for Australia ENVOY™ X1 TRANSCEIVER PRODUCT ENVOY-X1-TCVR-AUS PART NO. Envoy X1 Transceiver (Australia) DESCRIPTION Envoy™ X1 Transceiver The Envoy™ X1 Transceiver is a state-of- the-art software defined HF transceiver that delivers high performance but cost-effective voice communications for both base and mobile applications. The X1 Transceiver can be used with the 2221 or 2220 Handset or 2230 Desk Console. Both handset types and the desk console incorporate the new large format colour display and intuitive icon based menu system providing ease of use and programming. NOTE: The GPIO connector on the Envoy™ X1 Transceiver does not support any peripherals apart from a Morse Code Key. The standard transceiver consists of the parts listed below. The following pages detail the parts required for Envoy™ X1 Mobile and Base configurations. NOTE: • In Envoy™ X1 Mobile configurations, rubber feet (part number 30-11208-000) are not included. • In the Envoy™ X1 Base (with Console) configuration (ENVOY-X1-CONS-AUS), the handset cradle, external speaker and control cable (part numbers 15-00149, 15-00649 and 08-06022-001) are not included. COMPRISING: 08-07218-001 08-07000-001 15-00149 15-00649 08-06022-001 30-11208-000 15-10572 15-04177-EN 06-02809-EN • • • • • • • • EnvoyTM X1 2210 RF Unit EnvoyTM 2221 Limited Keyset Handset EnvoyTM 2220 Handset Cradle External Speaker with 4 m Lead Envoy™/NGT™ Handset Control Cable, 6 m Self Adhesive Rubber Feet (x4) Option for Australia, X1 EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card STANDARD FEATURES: • • • • • • • 400 channels, 1.6 to 30 MHz, 20 scan groups 250 Contact List entries Simultaneous scanning of multiple scan groups 100 W PEP, 12 V DC, USB/LSB/AM Ethernet/USB connectivity English language graphical user interface Codan Selcall (including Diagnostic, Phone and Emergency Call types) • GPS receiver port • In-built EasitalkTM speech noise reduction • MIL-STD-810G for Drop, Dust, Shock, Vibration AVAILABLE OPTIONS & ACCESSORIES: See pages 4 and 45 for Envoy™ X1 Options and Transceiver Accessories. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 15 Envoy™ X1 Configurations for Australia Envoy X1 Packages for Australia PART PART NO. ENVOY™ X1 PACKAGES Explorer Mobile Mobile (3040) Venturer Mobile Mobile (9350) ENVOY-X1ENVOY-X1ENVOY-X1ENVOY-X1MOB-EXPLORERMOBMOB-3040-AUS MOB-9350-AUS AUS VENTURER-AUS Base Base (with Console) ENVOY-X1BASE-AUS ENVOY-X1CONS-AUS CONSOLE 08-07204-001 15-60025 Cable, Envoy™ Console to 08-07205-006 RF Unit, 6 m 2230 Desk Console & Boom Microphone ANTENNAS 78-23086 3040 Spring 08-07148-001 9350 Main Assembly 08-05063-001 9350 Fibreglass Whip, 1.6 m 78-23007-003 9350 Tapered Stainless Steel Whip, 1.65 m 78-23056 9350 Tapered Stainless Steel Whip, 1.2 m 78-23025 9350 Spring 08-05140-001 Ant, TFD411, 125 W, 2–30 MHz, 34 m 15-00411-004 3040 Main Assembly 08-07007-001 Riser, Fibreglass, 0.8 m 78-18058 3040 Fibreglass Whip, 1.6 m 78-23085 3040 Stainless Steel Whip, 1.65 m INSTALLATION HARDWARE 15-00130 Complete Vehicle 15-00112 Installation Hardware Kit 3040 Installation Handbook (includes sealing kit) 15-60012 Automatic Tuning Whip Antenna 9350 Installation Handbook 15-04142-EN NGT™/Envoy™ RF Cradle & Battery Cable CABLES Control NGT™/Envoy™ to 08-05627-006 9350/304X Cable, 6 m Coax Assembly Cable, UHF Connectors RG58, 6m 08-01503-006 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 08-01503-030 Earth Braid, 1.5 m 05-06374 3020 Transceiver Supply 78-20022 Power IEC Cable 67-90305 TRANSCEIVER SUPPLY Page 16 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Envoy™ X2 Configurations for Australia ENVOY™ X2 TRANSCEIVER PRODUCT PART NO. ENVOY-X2-TCVR-AUS DESCRIPTION Envoy™ X2 Transceiver The Envoy™ X2 Transceiver is a state-of-the-art software defined HF transceiver delivering high performance voice and data communications and systems capabilities for both base and mobile applications. The X2 Transceiver can be used with the 2221 or 2220 Handset or 2230 Desk Console. Both handset types and the desk console incorporate the new large format colour display and intuitive icon based menu system providing ease of use and programming. Envoy X2 Transceiver (Australia) The standard transceiver consists of the parts listed below. The following pages detail the parts required for Envoy™ X2 Mobile and Base configurations. NOTE: • In Envoy™ X2 Mobile configurations, rubber feet (part number 30-11208-000) are not included. • In the Envoy™ X2 Base (with Console) configuration (ENVOY-X2-CONS-AUS), the handset cradle, external speaker and control cable (part numbers 15-00149, 15-00649 and 08-06022-001) are not included. COMPRISING: 08-07218-002 08-07000-001 15-00149 15-00649 08-06022-001 30-11208-000 15-10573 15-04177-EN 06-02809-EN • • • • • • • • EnvoyTM X2 2210 RF Unit EnvoyTM 2220 Handset EnvoyTM 2220 Handset Cradle External Speaker with 4 m Lead Envoy™/NGT™ Handset Control Cable, 6 m Self Adhesive Rubber Feet (x4) Option for Australia, X2 EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) • EnvoyTM Quick Reference Card STANDARD FEATURES: • • • • • • • • • • • 1000 channels, 1.6 to 30 MHz, 20 scan groups 500 Contact List entries Simultaneous scanning of multiple scan groups 100 W PEP, 12 V DC, USB/LSB/AM Ethernet/USB connectivity 15-way general purpose interface port (GPIO) for systems and accessory connectivity English language graphical user interface Codan Selcall (including Diagnostic, Phone and Emergency Call types) GPS receiver port In-built EasitalkTM speech noise reduction MIL-STD-810G for Drop, Dust, Shock, Vibration AVAILABLE OPTIONS & ACCESSORIES: ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 See pages 10 and 45 for Envoy X2 Options and Transceiver Accessories. Page 17 Envoy™ X2 Configurations for Australia Envoy X2 Packages for Australia PART PART NO. ENVOY™ X2 PACKAGES Mobile (3040) Mobile (9350) Base Base (with Console) ENVOY-X2-MOB3040-AUS ENVOY-X2-MOB9350-AUS ENVOY-X2BASE-AUS ENVOY-X2CONS-AUS CONSOLE 2230 Desk Console & Boom Microphone 08-07204-001 15-60025 Cable, Envoy™ Console to RF Unit, 6 m 08-07205-006 ANTENNAS 3040 Main Assembly 08-07007-001 Riser, Fibreglass, 0.8 m 78-18058 3040 Fibreglass Whip, 1.6 m 78-23085 3040 Stainless Steel Whip, 1.65 m 78-23086 3040 Spring 08-07148-001 9350 Main Assembly 08-05063-001 9350 Fibreglass Whip, 1.6 m 78-23007-003 9350 Tapered Stainless Steel Whip, 1.2 m 78-23025 9350 Spring 08-05140-001 Ant, TFD411, 125 W, 2–30 MHz, 34 m 15-00411-004 INSTALLATION HARDWARE NGT™/Envoy™ RF Cradle & Battery Cable 15-00130 Complete Vehicle Installation Hardware Kit 15-00112 3040 Installation Handbook 15-60012 (includes sealing kit) Automatic Tuning Whip Antenna 9350 Installation Handbook 15-04142-EN CABLES Control NGT™/Envoy™ to 9350/304X Cable, 6 m 08-05627-006 Coax Assembly Cable, UHF Connectors RG58, 6 m 08-01503-006 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 08-01503-030 Earth Braid, 1.5 m 05-06374 3020 Transceiver Supply 78-20022 Power IEC Cable 67-90305 TRANSCEIVER SUPPLY ## denotes language version Page 18 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT TRANSCEIVER NGT™ SR Configurations NGT™ SR TRANSCEIVER PRODUCT PART NO. NGT-SR-TCVR DESCRIPTION NGT™ SR Transceiver The NGTTM SR Transceiver is the ideal solution to meet all your advanced system requirements, including remote control, split-site, high power communications, or base and mobile applications. It also accommodates the use of multiple control points for simultaneous connection of peripheral equipment like data modems and telephone interconnects. The NGT™ SR comes with an RF unit, junction box, handset, speaker, cables, and mounting accessories for easy installation. NGTTM SR Transceiver The transceiver incorporates the exceptional features renowned in all Codan NGT™ Transceivers, plus advanced calling capabilities including Emergency call, Selective call, Phone call, Message call, Diagnostics, Remote disable and Remote configuration. Excellent options are available including Automatic Link Establishment (ALE) capabilities, voice encryption, and GPS, plus additional mounting accessories for multiple control points. The standard transceiver consists of the parts listed below. The following pages detail the parts required for NGT™ SR Mobile and Base configurations. COMPRISING: 08-05628-001 08-05629-001 08-05630-001 15-00129 15-00649 08-05610-006 30-11208-000 15-04127-## • • • • • • • • NGTTM SR 2010 RF Unit NGTTM SR 2020 Handset NGTTM SR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m Self Adhesive Rubber Feet (x4) NGTTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) STANDARD FEATURES: • • • • • 400 channels, 1.6–30 MHz, 10 networks Scanning of multiple networks 125 W PEP, 12 V DC, USB/LSB/AM In-built EasitalkTM speech noise reduction Meets MIL-STD-810F for shock, vibration and dust AVAILABLE OPTIONS & ACCESSORIES: See pages 22 and 45 for NGT™ SR Options and Transceiver Accessories. # denotes the cable variant depending upon country of use ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 19 NGT™ SR Configurations NGT™ SR MOBILE NGT™ SR Mobile PRODUCT PART NO. NGT-SR-MOB DESCRIPTION NGT™ SR Mobile Configuration The NGTTM SR Mobile Configuration consists of an NGTTM SR Transceiver, a 3040 Automatic Tuning Whip Antenna and cables, and vehicle installation hardware kit. COMPRISING: 08-05628-001 08-05629-001 08-05630-001 15-00129 15-00649 08-05610-006 15-04127-## NGT™ SR Transceiver • NGTTM SR 2010 RF Unit • NGTTM SR 2020 Handset • NGTTM SR 2030 Junction Box • NGTTM Handset Cradle Kit • External Speaker with 4 m Lead • CIB Interface Cable, 6 m • NGTTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) 3040 Automatic Tuning Whip with 6 m Cables The 3040 consists of the following parts. See page 89 for additional 3040 accessories. 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit 15-00130 NGT™/Envoy™ RF Cradle & Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. 15-00112 Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. AVAILABLE OPTIONS & ACCESSORIES: See pages 22 and 51 for NGT™ SR Options and Mobile Accessories. Page 20 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SR Configurations NGT™ SR BASE NGT™ SR Base PRODUCT PART NO. NGT-SR-BASE DESCRIPTION NGT™ SR Base Station Configuration The NGTTM SR Base Station Configuration consists of an NGTTM SR Transceiver, a a TFD411 Antenna, 3020 Heavy Duty Transceiver Supply, desk console, and cables. COMPRISING: 08-05628-001 08-05629-001 08-05630-001 15-10471-000 08-05610-006 30-11208-000 15-04127-## 15-00411-004 NGT™ SR Transceiver • NGTTM SR 2010 RF Unit • NGTTM SR 2020 Handset • NGTTM SR 2030 Junction Box • NGTTM SR Desk Console • CIB Interface Cable, 6 m • Self Adhesive Rubber Feet (x4) • NGTTM Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) TFD411 Antenna 125 W, 2–30 MHz, 34 m The antenna can be mounted horizontally between two support systems, or as an inverted “V” using a single central support mast. NOTE: Mast is not included. For masts, see page 107, Antenna Masts. 08-01503-030 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 30 m of high quality RG58 coaxial cable terminated with waterproof UHF style connectors. 78-20022 3020 Transceiver Supply Power supply to convert AC Mains into 13.8 V DC to power the Transceiver. 67-9030# Power IEC Cable, 2 m Used to connect 3020 Transceiver Supply to AC Mains source. For cable options, see page 83, 3020 Transceiver Supply. 05-06374 Earth Braid, 1.5 m Used to connect the RF Unit to ground point. AVAILABLE OPTIONS & ACCESSORIES: See pages 22 and 53 for NGT™ SR Options and Base Accessories. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 21 NGT™ SR Configurations NGT™ SR OPTIONS NGT™ SR Options PRODUCT PART NO. DESCRIPTION 15-10479 Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Standard call types include: Selective Call, All Call, Phone Call, Message Call, Diagnostic Call, Emergency Call. 15-10558 Opt, Default Open Selcall 15-10486 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option. For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. 15-10504-000 Opt External ALC (Factory Fit) Required when using an NGTTM high power system. NOTE: This option is also available as a retro fit kit (part number 15-10504). NGT™ SR Options Page 22 15-10513 Opt 100 W Reduces maximum transceiver output power to 100 W. 15-10481-000 Opt TxD, Tx Program Disabled (Factory Fit) Disables keypad programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. 15-10491-000 Opt TxP, Tx Program Prohibited (Factory Fit) Prohibits keypad programming of new transmit and receive frequencies. 15-10541-000 Opt High Speed Data (Factory Fit) Hardware modification required for use with Codan HF Data Modems using high speed waveforms (RM50e, 3212). 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SR Configurations NGT™ SR OPTIONS cont. NGT™ SR Options PRODUCT PART NO. 15-10507-000 DESCRIPTION Opt Voice Encryptor (Factory Fit) High grade Voice Encryptor Module for NGTTM series Transceivers. Provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10507). • This option is subject to Australian Defence Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10552-000 Opt AES-256 DV Encryptor Module (Factory Fit) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bps are available as standard. NOTE: • This option is also available as a retro fit kit (part number 15-10552). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10506-000 Opt 500 Hz BW Filter (Factory Fit) 500 Hz narrow band filter. Recommended for use with CW (morse code). 15-10514-000 Opt 2.7 kHz BW Second Filter (Factory Fit) 2.7 kHz wide band filter. Required for use with Codan RM50e HF Data Modems. 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for EnvoyTM /NGTTM series Transceivers. NOTE: This option is also available as a retro fit kit (part number 15-10469). Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 23 NGT™ SR Configurations This page has been intentionally left blank. Page 24 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ ASR Configurations NGT™ ASR TRANSCEIVER PRODUCT PART NO. NGT-ASR-TCVR DESCRIPTION NGT™ ASR Transceiver The NGTTM ASR Transceiver is specifically designed for interoperability with non-Codan HF transceiver systems. The NGT™ ASR supports MIL-STD-188-141B advanced Automatic Link Establishment, which has been certified for interoperability by the US Joint Interoperability Test Command (JITC). It is suitable for advanced system configurations in base and mobile applications, and supports HF data modems using advanced military waveforms. NGT™ ASR Transceiver The NGT™ ASR comes with an RF unit, junction box, handset, speaker, cables, and mounting accessories for easy installation. It incorporates the exceptional features renowned in all Codan NGT™ Transceivers, plus GPS, high power, encryption, and advanced calling capabilities. The standard transceiver consists of the parts listed below. The following pages detail the parts required for NGT™ ASR Mobile and Base configurations. COMPRISING: 08-05628-007 08-05629-007 08-05630-007 15-00129 15-00649 08-05610-006 30-11208-000 15-10486 15-10514-000 15-10541-000 15-04137-EN • • • • • • • • • • • NGTTM ASR 2010 RF Unit NGTTM ASR 2020 Handset NGTTM ASR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m Self Adhesive Rubber Feet (x4) Opt GPS Calling Opt 2.7 kHz BW Second Filter (Factory Fit) Opt High Speed Data (Factory Fit) NGTTM ASR Transceiver Getting Started Guide, includes Reference Manual on CDROM (English) STANDARD FEATURES: • • • • • • • • US FCC and NTIA approved MIL-STD-188-141B ALE included Last Heard Log and manual sounding 600 channels, 1.6–30 MHz, 20 networks Scanning of multiple networks 125 W PEP, 12 V DC, USB/LSB/AM In-built EasitalkTM speech noise reduction Meets MIL-STD-810F for shock, vibration and dust AVAILABLE OPTIONS & ACCESSORIES: See pages 28 and 45 for NGT™ ASR Options and Transceiver Accessories. # denotes the cable variant depending upon country of use Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 25 NGT™ ASR Configurations NGT™ ASR MOBILE NGT™ ASR Mobile PRODUCT PART NO. NGT-ASR-MOB DESCRIPTION NGT™ ASR Mobile Configuration The NGTTM ASR Mobile Configuration consists of an NGTTM ASR Transceiver, a 3040 Automatic Tuning Whip Antenna and cables, and vehicle installation hardware kit. COMPRISING: 08-05628-007 08-05629-007 08-05630-007 15-00129 15-00649 08-05610-006 15-10486 15-10514-000 15-10541-000 15-04137-EN NGT™ ASR Transceiver • NGTTM ASR 2010 RF Unit • NGTTM ASR 2020 Handset • NGTTM ASR 2030 Junction Box • NGTTM Handset Cradle Kit • External Speaker with 4 m Lead • CIB Interface Cable, 6 m • Opt GPS Calling • Opt 2.7 kHz BW Second Filter (Factory Fit) • Opt High Speed Data (Factory Fit) • NGTTM ASR Transceiver Getting Started Guide, includes Reference Manual on CDROM (English) 3040 Automatic Tuning Whip with 6 m Cables The 3040 consists of the following parts. See page 89 for additional 3040 accessories. 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit 15-00130 NGT™/Envoy™ RF Cradle & Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. 15-00112 Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. AVAILABLE OPTIONS & ACCESSORIES: See pages 28 and 51 for NGT™ ASR Options and Mobile Accessories. Page 26 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ ASR Configurations NGT™ ASR BASE NGT™ ASR Base PRODUCT PART NO. NGT-ASR-BASE DESCRIPTION NGT™ ASR Base Station Configuration The NGTTM ASR Base Station Configuration consists of an NGTTM ASR Transceiver, a TFD411 Antenna, 3020 Heavy Duty Transceiver Supply, desk console, and cables. COMPRISING: 08-05628-007 08-05629-007 08-05630-007 15-10471-000 08-05610-006 30-11208-000 15-10486 15-10514-000 15-10541-000 15-04137-EN 15-00411-004 NGT™ ASR Transceiver • NGTTM ASR 2010 RF Unit • NGTTM ASR 2020 Handset • NGTTM ASR 2030 Junction Box • NGTTM ASR Desk Console • CIB Interface Cable, 6 m • Self Adhesive Rubber Feet (x4) • Opt GPS Calling • Opt 2.7 kHz BW Second Filter (Factory Fit) • Opt High Speed Data (Factory Fit) • NGTTM ASR Transceiver Getting Started Guide, includes Reference Manual on CDROM (English) TFD411 Antenna 125 W, 2–30 MHz, 34 m The antenna can be mounted horizontally between two support systems, or as an inverted “V” using a single central support mast. NOTE: Mast is not included. For masts, see page 107, Antenna Masts. 08-01503-030 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 30 m of high quality RG58 coaxial cable terminated with waterproof UHF style connectors. 78-20022 3020 Transceiver Supply Power supply to convert AC Mains into 13.8 V DC to power the Transceiver. 67-9030# Power IEC Cable, 2 m Used to connect 3020 Transceiver Supply to AC Mains source. For cable options, see page 83, 3020 Transceiver Supply. 05-06374 Earth Braid, 1.5 m Used to connect the RF Unit to ground point. AVAILABLE OPTIONS & ACCESSORIES: See pages 28 and 53 for NGT™ ASR Options and Base Accessories. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 27 NGT™ ASR Configurations NGT™ ASR OPTIONS NGT™ ASR Options PRODUCT PART NO. 15-10504-000 NGT™ ASR Options DESCRIPTION Opt External ALC (Factory Fit) Required when using an NGTTM high power system. NOTE: This option is also available as a retro fit kit (part number 15-10504). 15-10513 Opt 100 W Reduces maximum transceiver output power to 100 W. 15-10481-000 Opt TxD, Tx Program Disabled (Factory Fit) Disables keypad programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. 15-10491 Opt TxP, Tx Program Prohibited Prohibits keypad programming of new transmit and receive frequencies. 15-10541-000 Opt High Speed Data (Factory Fit) Hardware modification required for use with Codan HF Data Modems using high speed waveforms (RM50e, 3212). 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. 15-10507-000 Opt Voice Encryptor (Factory Fit) High grade Voice Encryptor Module for NGTTM series Transceivers. Provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10507). • This option is subject to Australian Defence Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10552-000 Opt AES-256 DV Encryptor Module (Factory Fit) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bps are available as standard. NOTE: • This option is also available as a retro fit kit (part number 15-10552). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Continued on the next page Page 28 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ ASR Configurations NGT™ ASR OPTIONS CONT. NGT™ ASR Options PRODUCT PART NO. DESCRIPTION 15-10506-000 Opt 500 Hz BW Filter (Factory Fit) 500 Hz narrow band filter. Recommended for use with CW (morse code). 15-10514-000 Opt 2.7 kHz BW Second Filter (Factory Fit) 2.7 kHz wide band filter. Required for use with Codan RM50e HF Data Modems. 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for EnvoyTM /NGTTM series Transceivers. NOTE: This option is also available as a retro fit kit (part number 15-10469). ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 29 NGT™ ASR Configurations This page has been intentionally left blank. ## denotes language version Page 30 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SRx Configurations NGT™ SRx TRANSCEIVER PRODUCT PART NO. NGT-SRX-TCVR DESCRIPTION NGT™ SRx Transceiver The SRx comes with an RF unit, handset, speaker, cables, and mounting accessories for easy installation. The transceiver incorporates the exceptional features renowned in all Codan NGT™ Transceivers, plus advanced calling capabilities including Emergency call, Selective call, Phone call, Message call, Diagnostics, Remote disable and Remote configuration. Excellent options are available including Automatic Link Establishment (ALE) capabilities, voice encryption, and GPS, plus additional mounting accessories. The standard transceiver consists of the parts listed below. The following pages detail the parts required for NGT™ SRx Mobile and Base configurations. O SC DI The NGTTM SRx Transceiver, capable of voice, email, fax, GPS tracking, telephone interconnection and high power communications, is the ideal solution to meet your modern HF needs — all in a single cost effective unit. COMPRISING: N • • • • • • • NGTTM SRx 2012 RF Unit NGTTM SRx 2020 Handset NGTTM Handset Cradle Kit External Speaker with 4 m Lead Envoy™/NGT™ Handset Control Cable, 6 m Self Adhesive Rubber Feet (x4) NGTTM SRx Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) N TI 08-05628-009 08-05629-009 15-00129 15-00649 08-06022-001 30-11208-000 15-04140-## STANDARD FEATURES: General Purpose Interface Port (GPIO) 400 channels, 1.6–30 MHz, 10 networks Scanning of multiple networks 125 W PEP, 12 V DC, USB/LSB/AM In-built EasitalkTM speech noise reduction Morse capability Meets MIL-STD-810F for shock, vibration and dust ED U • • • • • • • AVAILABLE OPTIONS & ACCESSORIES: See pages 34 and 45 for NGT™ SRx Options and Transceiver Accessories. # denotes the cable variant depending upon country of use ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 31 NGT™ SRx Configurations NGT™ SRx MOBILE NGT™ SRx Mobile PRODUCT PART NO. DESCRIPTION NGT-SRX-MOB NGT™ SRx Mobile Configuration SC DI The NGTTM SRx Mobile Configuration consists of an NGTTM SRx Transceiver, a 9350 Automatic Tuning Whip Antenna and cables, and vehicle installation hardware kit. COMPRISING: NGT™ SRx Transceiver • NGTTM SRx 2012 RF Unit • NGTTM SRx 2020 Handset • NGTTM Handset Cradle Kit • External Speaker with 4 m Lead • Envoy™/NGT™ Handset Control Cable, 6 m • NGTTM SRx Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) 08-05628-009 08-05629-009 15-00129 15-00649 08-06022-001 15-04140-## O 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit N TI N 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 3040 Automatic Tuning Whip with 6 m Cables The 3040 consists of the following parts. See page 89 for additional 3040 accessories. NGT™/Envoy™ RF Cradle & Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. 15-00112 Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. ED U 15-00130 AVAILABLE OPTIONS & ACCESSORIES: See pages 34 and 51 for NGT™ SRx Options and Mobile Accessories. Page 32 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SRx Configurations NGT™ SRx BASE NGT™ SRx Base PRODUCT PART NO. NGT-SRX-BASE DESCRIPTION NGT™ SRx Base Station Configuration SC DI 08-05628-009 08-05629-009 15-00766 30-11208-000 15-04140-## 15-00411-004 The NGTTM SRx Base Station Configuration consists of an NGTTM SRx Transceiver, a TFD411 Antenna, 3020 Heavy Duty Transceiver Supply, and cables. COMPRISING: NGT™ SRx Transceiver • NGTTM SRx 2012 RF Unit • NGTTM SRx 2020 Handset • NGT Desk Console • Self Adhesive Rubber Feet (x4) • NGTTM SRx Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) O TFD411 Antenna 125 W, 2–30 MHz, 34 m The antenna can be mounted horizontally between two support systems, or as an inverted V using a single central support mast. N NOTE: Mast is not included. For masts, see page 107, Antenna Masts. 08-01503-030 TI 3020 Transceiver Supply Power supply to convert AC Mains into 13.8 V DC to power the Transceiver. U N 78-20022 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 30 m of high quality RG58 coaxial cable terminated with waterproof UHF style connectors. Power IEC Cable, 2 m Used to connect 3020 Transceiver Supply to AC Mains source. For cable options, see page 83, 3020 Transceiver Supply. 05-06374 Earth Braid, 1.5 m Used to connect the RF Unit to ground point. ED 67-9030# AVAILABLE OPTIONS & ACCESSORIES: See pages 34 and 53 for NGT™ SRx Options and Base Accessories. ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 33 NGT™ SRx Configurations NGT™ SRx OPTIONS NGT™ SRx Options PRODUCT PART NO. DESCRIPTION 15-10479 Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Standard call types include: Selective Call, All Call, Phone Call, Message Call, Diagnostic Call, Emergency Call. NGT™ SRx Options SC DI 15-10532 Opt MIL-STD-188-141B ALE Full This option provides full MIL-STD-188-141B ALE capability, including all capabilities provided by the FED-STD-1045 (part number 15-10560) option above. Additional call types include, NET Call, ANY Call, Group Call, Wildcard Call, in-link AMD Message Calls, as well as an advanced ALE beacon and Last Heard station log. 15-10558 Opt, Default Open Selcall O 15-10486 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). N TI NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option. For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. Opt External ALC (Factory Fit) Required when using an NGTTM high power system. N 15-10504-000 U NOTE: This option is also available as a retro fit kit (part number 15-10504). Opt 100 W Reduces transceiver output power to 100 W. 15-10481-000 Opt TxD, Tx Program Disabled (Factory Fit) Disables keypad programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. 15-10491 Opt TxP, Tx Program Prohibited Prohibits keypad programming of new transmit and receive frequencies. ED 15-10513 Continued on the next page ## denotes language version Page 34 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SRx Configurations NGT™ SRx OPTIONS CONT. NGT™ SRx Options PRODUCT PART NO. DESCRIPTION Opt High Speed Data (Factory Fit) Hardware modification required for use with Codan HF Data Modems using high speed waveforms (RM50e, 3212). 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. 15-10507-000 Opt Voice Encryptor (Factory Fit) High grade Voice Encryptor Module for NGTTM series Transceivers. Provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10507). • This option is subject to Australian Defence Export Controls. A signed End-User Declaration must be provided for supply of this option. O SC DI 15-10541-000 15-10556-000 N Opt ISB Processor 2012 (Factory Fit) Opt ISB Processor 2012 (Factory Fit) This option is used to provide Independent Sideband (ISB) high speed data capability when the transceiver is combined with an ISB capable RM50e HF Data Modem. Data rates of up to 19200 bps are possible in this configuration. 15-10552-000 U N TI NOTE: • This option is also available as a retro fit kit (part number 15-10556). • Codan 3012 & 3212 HF Data Modems are not supported when the ISB Option is fitted. • This option is only available with NGT™ SRx & MR Transceivers. • On-air compatible with ISB data option in Envoy X2 transceiver, see page 12 ED Opt AES-256 DV Encryptor Module (Factory Fit) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bps are available as standard. NOTE: • This option is also available as a retro fit kit (part number 15-10552). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Continued on the next page # denotes the cable variant depending upon country of use ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 35 NGT™ SRx Configurations NGT™ SRx OPTIONS CONT. NGT™ SRx Options PRODUCT PART NO. DESCRIPTION Opt 500 Hz BW Filter (Factory Fit) 500 Hz narrow band filter. Recommended for use with CW (morse code). 15-10514-000 Opt 2.7 kHz BW Second Filter (Factory Fit) 2.7 kHz wide band filter. Required for use with Codan RM50e HF Data Modems. 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for EnvoyTM /NGTTM series Transceivers. SC DI 15-10506-000 NOTE: This option is also available as a retro fit kit (part number 15-10469). ED U N TI N O Page 36 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ AR Configurations for Australia NGT™ AR TRANSCEIVER PRODUCT PART NO. NGT-AR-TCVR DESCRIPTION NGT™ AR Transceiver The NGTTM AR Transceiver is the ideal solution to meet all your modern HF needs from voice, email, fax, GPS tracking, and telephone interconnection to remote control, split-site and high power communications. It is suitable for base and vehicle applications, and is easy to use with an innovative, mobile phone-like handset with one-button shortcuts. Plus Codan’s Easitalk™ guarantees clear communications. The AR Transceiver comes with an NGT™ RF unit, junction box, speaker, and mounting accessories for easy installation. The radio incorporates the exceptional features renowned in all Codan NGT™ Transceivers, plus advanced calling capabilities including Emergency call, Selective call, Phone call, Message call, Diagnostics, Remote Disable and Remote Configuration. Excellent options are available including Automatic Link Establishment (ALE), voice encryption, and GPS, plus additional mounting accessories. The standard transceiver consists of the parts listed below. The following pages detail the additional parts required for NGT™ AR Mobile and Base configurations. NOTE: • In NGT™ AR Mobile configurations, rubber feet (part number 30-11208-000) are not included. • In the NGT™ AR Base configuration (NGT-AR-BASE-CON), the handset cradle and external speaker (part numbers 15-00129 and 15-00649) are not included. 08-05628-003 08-05629-003 08-05630-003 15-00129 15-00649 08-05610-006 30-11208-000 15-04127-EN COMPRISING: • • • • • • • • NGTTM AR 2010 RF Unit NGTTM AR 2020 Handset NGTTM AR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m Self Adhesive Rubber Feet NGTTM Transceiver Getting Started Guide, includes Reference Manual on CDROM STANDARD FEATURES: • 400 channels, 1.6–30 MHz, 20 networks • Scanning of multiple networks • 100 W PEP, 12 V DC, USB • In-built EasitalkTM speech noise reduction • Phone call • Selective call • Message call (64 characters) • Morse capability • Remote diagnostics with remote configuration and transmit disable capability • Meets MIL-STD-810F for shock, vibration and dust AVAILABLE OPTIONS & ACCESSORIES: See pages 39 and 45 for NGT™ AR Options and Transceiver Accessories. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 37 NGT™ AR Configurations for Australia PART PART NO. NGT™ AR PACKAGES Mobile (3040) Mobile (9350) Base NGT-AR-MOB-3040 NGT-AR-MOB NGT-AR-BASE-CON CONSOLE NGT™ AR Desk Console 15-10471-000 NGT AR Packages for Australia ANTENNAS 3040 Main Assembly 08-07007-001 Riser, Fibreglass, 0.8 m 78-18058 3040 Fibreglass Whip, 1.6 m 78-23085 3040 Stainless Steel Whip, 1.65 m 78-23086 3040 Spring 08-07148-001 9350 Main Assembly 08-05063-001 9350 Fibreglass Whip, 1.6 m 78-23007-003 9350 Tapered Stainless Steel Whip, 1.65 m 78-23056 9350 Tapered Stainless Steel Whip, 1.2 m 78-23025 9350 Spring 08-05140-001 Ant, TFD411, 125 W, 2–30 MHz, 34 m 15-00411-004 INSTALLATION HARDWARE NGT™/Envoy™ RF Cradle & Battery Cable 15-00130 Complete Vehicle Installation Hardware Kit 15-00112 3040 Installation Handbook 15-60012 (includes sealing kit) Automatic Tuning Whip Antenna 9350 Installation Handbook 15-04142-EN CABLES Control NGT™/Envoy™ to 9350/304X Cable, 6 m 08-05627-006 Coax Assembly Cable, UHF Connectors RG58, 6 m 08-01503-006 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 08-01503-030 Earth Braid, 1.5 m 05-06374 3020 Transceiver Supply 78-20022 Power IEC Cable 67-90305 TRANSCEIVER SUPPLY Page 38 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ AR Configurations for Australia NGT™ AR OPTIONS NGT AR Options PRODUCT PART NO. DESCRIPTION 15-10479 NGT AR Options Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Includes facilities for Selective Calls, All Calls, Phone Calls, Text Messaging and GPS Position Calls. 15-10486 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option. For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. 15-10480 Opt E Enables digital Selective Emergency call. This is not required for RFDS Emergency calling. 15-10504-000 Opt External ALC (Factory Fit) Required when using an NGTTM high power system. NOTE: This option is also available as a retro fit kit (part number 15-10504). 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for EnvoyTM /NGTTM series Transceivers. NOTE: This option is also available as a retro fit kit (part number 15-10469). Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 39 NGT™ AR Configurations for Australia NGT™ AR OPTIONS CONT. NGT AR Options PRODUCT PART NO. DESCRIPTION 15-10507-000 Opt Voice Encryptor (Factory Fit) High grade Voice Encryptor Module for NGT™ series Transceivers. Provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is also available as a retro fit kit (part number 15-10507). • This option is subject to Australian Defence Export Controls. A signed End-User Declaration must be provided for supply of this option outside of Australia. 15-10552-000 Opt AES-256 DV Encryptor Module (Factory Fit) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bps are available as standard. NOTE: • This option is also available as a retro fit kit (part number 15-10552). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Page 40 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SRx Configurations for Australia NGT™ SRx TRANSCEIVER NGT SRx Transceiver PRODUCT PART NO. NGT-SRX-TCVR-AUS DESCRIPTION NGT™ SRx Transceiver The NGTTM SRx Transceiver is the ideal solution to meet your modern HF needs including voice, email, fax, GPS tracking and telephone interconnection — all in a single cost effective unit. The radio incorporates the exceptional features renowned in all Codan NGT™ radios, plus advanced calling capabilities including Emergency call, Selective call, Phone call, Message call, Diagnostics, Remote disable and Remote configuration. Excellent options are available including Automatic Link Establishment (ALE) capabilities, voice encryption, and GPS, plus additional mounting accessories. The standard transceiver consists of the parts listed below. The following pages detail the additional parts required for NGT™ SRx Mobile and Base configurations. O SC DI The SRx Transceiver comes with an NGT™ RF unit, speaker, and mounting accessories for easy installation, and is suitable for base and vehicle applications. NOTE: In NGT™ SRx Mobile configurations, rubber feet (part number 30-11208-000) are not included. N N TI 08-05628-009 08-05629-009 15-00129 15-00649 08-06022-001 30-11208-000 15-10540 15-04140-EN COMPRISING: • NGTTM SRx 2012 RF Unit • NGTTM SRx 2020 Handset • NGTTM Handset Cradle Kit • External Speaker with 4 m Lead • Envoy™/NGT™ Handset Control Cable, 6 m • Self Adhesive Rubber Feet • Opt SRx for Australia • NGTTM SRx Transceiver Getting Started Guide, includes Reference Manual on CDROM ED U STANDARD FEATURES: • General Purpose Interface Port (GPIO) • 400 channels, 1.6–30 MHz, 10 networks • Scanning of multiple networks • 100 W PEP, 12 V DC, USB • In-built EasitalkTM speech noise reduction • Phone call • Selective call • Message call (64 characters) • Morse capability • Remote diagnostics with remote configuration and transmit disable capability Meets MIL-STD-810F for shock, vibration and dust AVAILABLE OPTIONS & ACCESSORIES: • See pages 49 and 45 for NGT™ SRx Options and Transceiver Accessories. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 41 NGT™ SRx Configurations for Australia PART PART NO. NGT™ SRx PACKAGES Mobile (3040) Mobile (9350) Base NGT-SRX-MOB-3040 NGT-SRX-MOB-AUS NGT-SRX-BASE-AUS CONSOLE NGT™ SRx Desk Console 15-00766 NGT AR Packages for Australia SC DI ANTENNAS 3040 Main Assembly 08-07007-001 Riser, Fibreglass, 0.8 m 78-18058 3040 Fibreglass Whip, 1.6 m 78-23085 3040 Stainless Steel Whip, 1.65 m 78-23086 3040 Spring 08-07148-001 9350 Main Assembly 08-05063-001 9350 Fibreglass Whip, 1.6 m 78-23007-003 O 78-23025 9350 Spring 08-05140-001 Ant, TFD411, 125 W, 2–30 MHz 15-00411-004 INSTALLATION HARDWARE 15-00130 Complete Vehicle Installation Hardware Kit 15-00112 Automatic Tuning Whip Antenna 9350 Installation Handbook 15-04142-EN 08-05627-006 Coax Assembly Cable, UHF Connectors RG58, 6 m 08-01503-006 Coax Assembly Cable, UHF Type Connectors, RG58, 30 m 08-01503-030 Earth Braid, 1.5 m 05-06374 ED Control NGT™/Envoy™ to 9350/304X Cable, 6 m U CABLES TRANSCEIVER SUPPLY N 3040 Installation Handbook 15-60012 (includes sealing kit) TI NGT™/Envoy™ RF Cradle & Battery Cable N 9350 Tapered Stainless Steel Whip, 1.2 m 3020 Transceiver Supply 78-20022 Power IEC Cable 67-90305 NGT SRx Packages for Australia Page 42 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT™ SRx Configurations for Australia NGT™ SRx OPTIONS NGT SRx Options PRODUCT PART NO. 15-10540 NGT SRx Options DESCRIPTION Opt SRx for Australia This option provides Australian compliance for NGT™ SRx Transceivers. SC DI NOTE: • This option also includes digital Selective Emergency call (Opt E, part number 15-10480). • This option is for Australian customers only. Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Includes facilities for Selective Calls, All Calls, Phone Calls, Text Messaging and GPS Position Calls. 15-10486 Opt GPS Calling Enables sending and receiving of GPS position information using Selcall or ALE (if enabled). O 15-10479 N NOTE: This feature is compatible with GPS receivers providing NMEA 0183 V2.0 (or later) output format. A GPS receiver is not supplied as part of this option. For a description of the GPS receiver available from Codan, see page 51, Mobile Accessories. TI 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. N 15-10469-000 Opt Fan (Factory Fit) Fan unit for continuous data transmission for EnvoyTM /NGTTM series Transceivers. U NOTE: This option is also available as a retro fit kit (part number 15-10469). Continued on the next page ED Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 43 NGT™ SRx Configurations for Australia NGT™ SRx OPTIONS CONT. NGT SRx Options PRODUCT PART NO. DESCRIPTION 15-10507-000 Opt Voice Encryptor (Factory Fit) High grade Voice Encryptor Module for NGT™ series Transceivers. Provides high grade voice security with exceptional recovered audio quality. SC DI NOTE: • This option is also available as a retro fit kit (part number 15-10507). • This option is subject to Australian Defence Export Controls. A signed End-User Declaration must be provided for supply of this option outside of Australia. 15-10552-000 Opt AES-256 DV Encryptor Module (Factory FIt) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bps are available as standard. ED U N TI N O NOTE: • This option is also available as a retro fit kit (part number 15-10552). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Page 44 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories TRANSCEIVER ACCESSORIES PRODUCT Transceiver Accessories PART NO. 08-07000-001 For ENVOY SERIES 08-07000-002 For ENVOY SERIES 08-06022-002 08-06022-001 08-06022-003 DESCRIPTION Envoy™ 2220 Handset The 2220 Handset provides full programming and operation of the Envoy™ X1 and X2 Transceivers from the handset. It features a large format colour screen, easy-to-use navigation keys, and a full alphanumeric keypad including special function macros. The handset also features a micro USB port for PC (TPS-3250) and memory stick programming/firmware upgrade and control of the embedded transceiver modem (if enabled). Envoy™ 2221 Limited Keyset Handset The 2221 reduced keypad Handset is compatible with Envoy™ X1 and X2 Transceivers and supports the same capabilities as the 2220 Handset but is tailored for basic operation. The 2221 Handset is most suited for transceivers that will be configured by PC (TPS-3250) or memory stick prior to deployment but handset based programming is available. Cable, NGT / Envoy™ Handset Control, 0.5 m Cable, NGT / Envoy™ Handset Control, 6 m Cable, NGT / Envoy™ Handset Control, 30 m For ENVOY SERIES 08-07205-001 08-07205-006 08-07205-030 Cable, Envoy™ Console to RF Unit, 1 m Cable, Envoy™ Console to RF Unit, 6 m Cable, Envoy™ Console to RF Unit, 30 m For ENVOY SERIES 08-05610-001 08-05610-002 08-05610-006 08-05610-030 Cable, CIB Interface, 0.5 m Cable, CIB Interface, 2 m Cable, CIB Interface, 6 m Cable, CIB Interface, 30 m Transceiver Accessories For SR, ASR, AR 08-06213-001 For ASR Cable, VP-116 Interface Interface cable for connecting a VP-116 Voice Privacy Unit to an NGTTM ASR VP-116 Junction Box. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 45 Transceiver Accessories TRANSCEIVER ACCESSORIES CONT. Transceiver Accessories PRODUCT DESCRIPTION PART NO. 08-06222-001 For ASR 08-06330-001 For ASR Page 46 Junction Box, NGT™ ASR VP-116 NGTTM ASR Junction Box suitable for interfacing with a VP-116 Voice Privacy Unit. Replaces the standard NGTTM ASR Junction Box. Cable, NGT™ to Q9600 Modem, 1 m Interface cable for an NGTTM ASR Junction Box to a RockwellCollins Q9600 Modem. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories TRANSCEIVER ACCESSORIES CONT. Transceiver Accessories PRODUCT DESCRIPTION PART NO. 08-03255 Cable, Battery, 6 m For ALL TCVRS 08-03255-008 Cable, Battery, 8 m For ALL TCVRS 08-04515-001 Earth Wire, 0.5 m For ALL TCVRS 05-06374 Earth Braid, 1.5 m For ALL TCVRS 15-04178-CD For ENVOY SERIES 08-07214-001 For ENVOY SERIES 67-90406 For ENVOY SERIES TPS-3250 Envoy™ Programming Software CD Software used to program Envoy™ series Transceivers. Envoy™ Programming Cable (part number 08-07214-001) needs to be ordered separately. Cable, Envoy™ USB Programming Interface cable to program Envoy™ series Transceivers from a PC. Cable, USB Adaptor for Memory Stick Programming Enables connection of a conventional USB memory stick to Envoy™ series Handset or Desk Console. USB to 6-way data interface cable for use with MIL-STANAG 2G Data (using RC50-C application). Cable connects to 6-way serial port on Envoy transceiver RF unit. 08-07318-001 08-07318-002 Cable, USB to 6-way (6 m) Cable, USB to 6-way (2 m) For ENVOY SERIES Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 47 Transceiver Accessories TRANSCEIVER ACCESSORIES CONT. Transceiver Accessories PRODUCT DESCRIPTION PART NO. USB to 15-way data interface cable for use with MIL-STANAG 2G Data (using RC50-C application), and Opt 2400 bps Internal Data Modem (using UUPlus applications). Cable connects to 15-way GP port on Envoy transceiver RF unit. 08-06952-001 08-06952-002 Cable, USB to 15-way (2 m) Cable, USB to 15-way (6 m) For ENVOY SERIES 15-04168-EN For ALL TCVRS Key Management Software 15-04171-EN For ALL TCVRS Key Management Software (KMS) Key Management Software (KMS) enables you to manage and program encryption keys for Codan’s NGT™/2110/ Envoy™ series Transceivers and stand-alone encrypted devices, e.g. RM50e HF Data Modem. NOTE: • This product is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Key Fill Software (KFS) Key Fill Software (KFS) enables you to program encryption keys into Codan’s NGT™/2110/Envoy™ series Transceivers and stand-alone encryption devices, e.g. RM50e HF Data Modem. NOTE: • This product is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 08-06380-001 For SRx, AR Voice & ENVOY SERIES 08-06266-001 For SRx, SR, ASR, AR & ENVOY X2 Cable, Serial 6-way to D9F 9-way D to 6-way Molex Interface Cable for transceiver serial control of NGT™ SRx, AR Voice and Envoy™ X1 & X2 Transceivers. Cable, Data Interface D9F to D15M 9-way D to 15-way D Interface Cable for transceiver serial control for Envoy™ X2 Transceivers. The cable can also be used for key programming (KMS/KFS) for NGT™ SRx, SR, ASR, AR . Continued on the next page Page 48 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories TRANSCEIVER ACCESSORIES CONT. Transceiver Accessories PRODUCT DESCRIPTION PART NO. 15-04164-EN For NGT SERIES 08-05123-001 For NGT SERIES 78-01031 For NGT SERIES NSP Software CD Package Software used to program NGTTM series Transceivers. NSP interface cable (part number 08-05123-001) needs to be ordered separately. Cable, NSP Interface Interface cable to program NGTTM series Transceivers from a PC. Adaptor, USB to DB-9, Serial Port USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. Not suitable to be used when upgrading transceiver firmware. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 49 Transceiver Accessories TRANSCEIVER ACCESSORIES PRODUCT Transceiver Accessories PART NO. 15-00662 For SRx, SR, ASR & ENVOY SERIES 15-00668 For ENVOY SERIES 08-06262-001 For NGT and ENVOY SERIES 15-10469-000 DESCRIPTION Morse Key for NGT™/Envoy™ Morse Key to suit NGT™/Envoy™ for desktop operation. Terminated to 15-way GP port connector. Morse Key, 2230 Desk Console Morse key for use with the Envoy 2230 Desk Console. Connects to the 8 pin accessory connector. Dual Antenna Selector Antenna selector switch used for connecting two antennas to an NGT/Envoy RF Unit. The dual antenna switch connects to the RF coax and antenna control connectors of the RF Unit. The switch supports the connection of one 9103 tuner and an HF broadband antenna or two HF broadband antennas. Coaxial connectors are UHF type. Opt Fan (Factory Fit) Fan unit for continuous data transmission for Envoy™/NGT™ series Transceivers. NOTE: This option is also available as a retro fit kit (part number 15-10469). 15-04177-EN For ENVOY SERIES Getting Started Guide, Envoy™ Transceiver, includes Reference Manual on CDROM Printed Getting Started Guide for the Envoy™ Transceiver. See page 165, Language Support for translations of this guide. 15-04143-EN Repair Guide, NGT™ Transceiver (English) Printed Repair Guide for the NGT™ series Transceiver. For NGT SERIES 15-04143-CD Repair Guide, NGT™ Transceiver, on CDROM (English) For NGT SERIES Continued on the next page Page 50 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories TRANSCEIVER ACCESSORIES CONT. Transceiver Accessories PRODUCT DESCRIPTION PART NO. 15-04127-## For NGT SERIES Getting Started Guide, NGT™ Transceiver, includes Reference Manual on CDROM Printed Getting Started Guide for the NGTTM Transceiver. See page 165, Language Support for translations of this guide. 15-04137-## For ASR Getting Started Guide, NGT™ ASR Transceiver, includes Reference Manual on CDROM Printed Getting Started Guide for the NGTTM Transceiver. See page 165, Language Support for translations of this guide. MOBILE ACCESSORIES PRODUCT Transceiver Mobile Accessories PART NO. 15-00771 For SR, ASR, AR Mobile Accessories DESCRIPTION GPS Receiver/Antenna Includes: • Receiver/antenna • Magnetic mounting bracket • NGT™ Transceiver interconnecting cables to suit 15 pin NGT™ Junction Box connector Features: • Integrated antenna and GPS receiver • Tracking up to 12 satellites 15-00765 For SRx, AR Voice, SRx (AUS) & ENVOY SERIES GPS Receiver/Antenna Includes: • Receiver/antenna • Magnetic mounting bracket • NGT™/Envoy™ Transceiver interconnecting cables Features: • Integrated antenna and GPS receiver • Tracking up to 12 satellites Envoy X1 Mobile Accessories 08-05847-001 For SR, ASR, AR 15-00704 For ALL TCVRS Interface Adaptor Interface adaptor to enable simultaneous connection of a GPS receiver and a 3012 HF Data Modem to the NGT™ Transceiver. Vehicle Interference Suppression Kit Comprises of interference filters, copper braid, earth strap and fitting instructions. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 51 Transceiver Accessories MOBILE ACCESSORIES CONT. PRODUCT Transceiver Mobile Accessories PART NO. 15-00508 For ALL TCVRS 15-00130 For ALL TCVRS 15-60031 For ALL TCVRS 15-00112 DESCRIPTION Voltage Regulator (24 V to 12 V operation 20 A) Enables the operation of NGT™/Envoy™ series Transceivers in 24/26 V based systems. Protected from faults such as voltage spikes, overload, short circuits and low voltage input. The unit automatically resets once a fault is removed. NGT™/Envoy™ RF Cradle & 6 m Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 6 m battery cable. NGT™/Envoy™ RF Cradle & 8 m Battery Cable Includes mounting cradle, fuse holder and fuse, earth wire and 8 m battery cable. Complete Vehicle Installation Hardware Kit Includes assorted screws, cable ties and grommets. For ALL TCVRS 15-00136 Cradle, Envoy™/NGT™ RF Unit Mounting For ALL TCVRS 15-00129 Cradle Kit, NGT™ Handset For NGT SERIES 15-00149 Cradle Kit, Envoy™ Handset For ENVOY SERIES 08-03255 Cable, Battery, 6 m For ALL TCVRS 08-03255-008 Cable, Battery, 8 m For ALL TCVRS Continued on the next page Page 52 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories MOBILE ACCESSORIES CONT. PRODUCT Transceiver Mobile Accessories PART NO. 15-00702 For ALL TCVRS DESCRIPTION Cable Kit for Float Charge Cable kit for float charging lead-acid storage battery for uninterrupted supply. For batteries, see page 86, Batteries. 15-00711 Fuse Holder with 32 A Fuse For ALL TCVRS 15-00712 Fuse, 32 A For ALL TCVRS BASE ACCESSORIES PRODUCT Transceiver Base Accessories PART NO. 08-07204-001 For ENVOY SERIES Base Accessories 15-10471 For SR, ASR, AR DESCRIPTION Desk Console 2230, Envoy™ An optional Envoy™ Desk Console for the Envoy™ Transceiver, incorporating an in-built speaker, hand PTT switch, in-built headphone output, and a 2 m transceiver interface cable. NOTE: The standard microphone for the 2230 Desk Console is the Boom Microphone (part number 15-60025) and must be ordered separately to the main console unit. The 2230 Desk Console may connect to the Envoy™ RF Unit via a dedicated control cable (part number 08-07205-00X), see page 45, Transceiver Accessories, or via Ethernet, see page 117, Envoy Remote Control Accessories — Ethernet. Desk Console, NGT™ SR/ASR/AR An optional NGT™ SR/ASR/AR Desk Console for the NGT™ Transceiver, incorporating an in-built speaker, hand PTT switch, goose-neck microphone, and in-built headphone output. NOTE: When an SR/ASR/AR Transceiver is ordered with a desk console, part number 15-10471-000 should be used for the console so that the junction box will be fitted to the console at the factory. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 53 Transceiver Accessories BASE ACCESSORIES CONT. PRODUCT Transceiver Base Accessories PART NO. 15-00766 For VR, SRx, AR Voice, SRx (AUS) DESCRIPTION Desk Console, NGT™ VR/SRx/AR Voice An optional NGT™ VR/SRx/AR Voice Desk Console for the NGT™ VR/SRx/AR Voice Transceiver, incorporating an in-built speaker, hand PTT switch, goose-neck microphone, in-built headphone output, and a 2 m transceiver interface cable. NOTE: When the transceiver is ordered with an optional desk console (part number 15-00766), an NGT™ handset cradle (part number 15-00129), external speaker (part number 15-00649) and NGT™ Control cable (part number 08-06022-001) are not included. 15-00602 Desk Console Headphones, NGT™ Headphones suitable for the NGTTM ASR Desk Console. For NGT SERIES 15-60028 Desk Console Headphones, Envoy™ Headphones suitable for the Envoy™ Desk Console. For ENVOY SERIES 15-60026 Desk Console Headset, Envoy™ For ENVOY SERIES 15-60025 Desk Console Boom Microphone, Envoy™ For ENVOY SERIES ## denotes language version Page 54 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories BASE ACCESSORIES CONT. PRODUCT Transceiver Base Accessories PART NO. 15-60024 DESCRIPTION Desk Console Hand-held Microphone, Envoy™ For ENVOY SERIES 15-60027 Desk Console PTT footswitch, Envoy™ For ENVOY SERIES CONTROL-POINT-ASR-6M 15-00668 Morse Key, 2230 Desk Console Morse key for use with the Envoy 2230 Desk Console. Connects to the 8 pin accessory connector. For ASR NGT™ ASR Control Point Kit An additional control point incorporating the following parts. COMPRISING: NGT™ ASR Base Accessories 08-05629-007 08-05630-007 15-00129 15-00649 08-05610-006 NGTTM ASR 2020 Handset NGTTM ASR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 55 Transceiver Accessories BASE ACCESSORIES CONT. PRODUCT CONTROL-POINT-SR-6M Transceiver Base Accessories PART NO. For SR DESCRIPTION NGT™SR Control Point Kit An additional control point incorporating the following parts. COMPRISING: NGT™ SR Base Accessories CONTROL-POINT-AR-6M 08-05629-001 08-05630-001 15-00129 15-00649 08-05610-006 NGTTM SR 2020 Handset NGTTM SR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m For AR NGT™ AR Control Point Kit An additional control point incorporating an NGT™ AR 2020 Handset and cradle, NGT™ AR 2030 Junction Box, loudspeaker and 6 m CIB cable. COMPRISING: 08-05629-003 08-05630-003 15-00129 15-00649 08-05610-006 Page 56 NGTTM AR 2020 Handset NGTTM AR 2030 Junction Box NGTTM Handset Cradle Kit External Speaker with 4 m Lead CIB Interface Cable, 6 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Accessories This page has been intentionally left blank. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 57 Transceiver Accessories This page has been intentionally left blank. Page 58 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email NGT RC50-C HF EMAIL SOFTWARE PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-04161-CD RC50-C HF Email Software RC50-C HF Email Software Codan’s RC50-C HF Email software provides fast, efficient, error free email capability over HF radio. Operating in conjunction with Codan’s HF Transceivers and 2G Data Modems, the software operates on a standard Windows™ PC using a single USB port with no specialised PC hardware requirements. When installed, the software runs in the background requiring no user interaction. Data & Email COMPATIBILITY: RC50-C HF Email Software For use with external RM50e HF Data Modem (NGT™ AR, SRx, SR, ASR, Envoy™ X2 Transceivers) and 2G embedded data modem (Envoy X2 and 2110 Manpack transceiver) COMPRISING: • CD-ROM with RC50-C software and documentation STANDARD FEATURES: • • • • • Adaptive rates up to 19200 bit/s (ISB only) or 9600 bit/s Compatible with ALE/CALM™ Intranet/Internet gateway NATO interoperable ISB capable SYSTEM REQUIREMENTS: • • • • • • • Windows™ XP Professional SP2 or Windows™ 7 Intel Pentium IV 800 MHz or better 6 GB or more of free space for email storage 512 MB or more of RAM CD-ROM drive POP3 / SMTP compliant email client Access to any commercial POP3 / SMTP compliant email server for internet connectivity • Serial/USB port for connecting the HF modem to the PC NOTE: • The ISB capability is only supported by an NGT™ SRx Transceiver fitted with the ISB Option, see page 35, Opt ISB Processor 2012 (Factory Fit) or Envoy X2 fitted with 2G data options (15-10589-000 or 15-10590-000) and the ISB option (15-10598). • Requires Data Interface Cable (part number 08-06901-001) for connecting PC to an RM50e data modem. • Requires Data Interface Cable (08-06952 or 08-07318) for connecting the PC to an Envoy with 2G Data Modem option (part number 15-10589). Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 59 Data & Email RC50-C CABLE OPTIONS PRODUCT PART NO. DESCRIPTION USB to 6-way data interface cable for use with MIL-STANAG 2G Data (using RC50-C application). Cable connects to 6-way serial port on Envoy transceiver RF unit. 08-07318-001 08-07318-002 Cable, USB to 6-way (2 m) Cable, USB to 6-way (6 m) For ENVOY SERIES USB to 15-way data interface cable for use with MIL-STANAG 2G Data (using RC50-C application) cable connects to 15-way GP port on Envoy transceiver RF unit. 08-06952-001 08-06952-002 Cable, USB to 15-way (2 m) Cable, USB to 15-way (6 m) For ENVOY SERIES USB to 19-way MIL Interface Cable for use with RM50e HF Data Modem (using RC50-C application. Cable connects to 19-pin connector on RM50e HF Data Modem. 08-06901-001 Page 60 Cable, Data Interface 19-way MIL to USB A, (2 m) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email UUPLUS™ SOFTWARE PRODUCT PART NO. DESCRIPTION 08-05981-001 UUPlus™ Email for HF Server Software UUPlus ™ Email for HF Server Software Provides HF and Internet email access for up to 25 users. It works in conjunction with UUPlusTM Email for HF Codan Client software, used by each remote station. It has been specifically designed for use with Codan’s HF equipment. Data & Email UUPlus Software NOTE: • One copy of UUPlusTM Codan Client is required for each user that is to connect to UUPlusTM Codan Server. • A UUPlusTM Codan Server cannot communicate directly to other UUPlusTM Codan Server stations. COMPATIBILITY: • For use with 3012 and 3212 HF Data Modems, and Envoy™ X2 2400 bit/s embedded modem COMPRISING: • CD-ROM with UUPlusTM Codan Server software and documentation • Single user licence for installation on one machine STANDARD FEATURES: • Simple to install and maintain. • Works with POP3/SMTP PC email clients such as Outlook Express™. • Reduces connection time by compressing and combining messages • Automatically resumes interrupted file transfers • Capable of automatically calling the remote user at preset times to deliver mail and collect outgoing mail, or enables the user to check mail manually SYSTEM REQUIREMENTS: • Codan HF SSB Transceiver • Microsoft WindowsTM XP/WIN7 • Internet email client with support of POP3 and SMTP protocols • Serial/USB port for connecting the HF modem to the PC • Optional LAN, dialup networking card or line modem for connecting local email clients and server to the internet • Codan 3012, 3212 HF Data Modems or Envoy X2 2400 bit/s embedded modem Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 61 Data & Email UUPLUS CABLE OPTIONS PRODUCT PART NO. DESCRIPTION USB to 15-way data interface cable for use with 2400 bit/ embedded data modem (using UUPlus applications) cable connects to 15-way GP port on Envoy transceiver RF unit. 08-06952-001 08-06952-002 Cable, USB to 15-way (2 m) Cable, USB to 15-way (6 m) For ENVOY SERIES 9-way to 9-way serial data interface cable to connect PC (using UUPlus applications) to 3012 data modem. 08-05086-001 08-05086-006 Data Interface Cable (2 m) Data Interface Cable (6 m) 78-01031 Adaptor, USB to DB-9, Serial USB to 9-way serial adaptor cable. USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. Page 62 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email UUPLUS™ SOFTWARE PRODUCT PART NO. DESCRIPTION 08-05980-001 UUPlus™ Email for HF Client Software UUPlus™ Email for HF Client Software Simple and reliable solution for sending email over HF from remote areas. It works in conjunction with UUPlusTM Codan Server software and has been specifically designed for use with Codan’s HF equipment. COMPATIBILITY: • For use with 3012 and 3212 HF Data Modems, and Envoy™ X2 2400 bit/s embedded modem COMPRISING: • CD-ROM with UUPlusTM Codan Client software and documentation • Single user licence for installation on one machine STANDARD FEATURES: • Simple to install and maintain. • Works with POP3/SMTP PC email clients such as Outlook Express™. • Reduces connection time by compressing and combining messages • Automatically resumes interrupted file transfers • Capable of automatically answering calls from the server to exchange mail at preset times, or enables the user to check for mail manually • Able to send files directly to other stations SYSTEM REQUIREMENTS: • Codan HF SSB Transceiver • Microsoft WindowsTM XP/WIN7 • Internet email client with support of POP3 and SMTP protocols • Codan 3012, 3212 HF Data Modem or Envoy X2 2400 bit/s embedded modem • Serial/USB port for connecting the HF modem to the PC Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 63 Data & Email UUPLUS CABLE OPTIONS PRODUCT PART NO. DESCRIPTION USB to 15-way data interface cable for use with 2400 bit/s internal data modem (using UUPlus applications) cable connects to 15-way GP port on Envoy transceiver RF unit. 08-06952-001 08-06952-002 Cable, USB to 15-way (2 m) Cable, USB to 15-way (6 m) For ENVOY SERIES 9-way to 9-way serial data interface cable to connect PC (using UUPlus applications) to 3012 data modem. 08-05086-001 08-05086-006 Data Interface Cable (2 m) Data Interface Cable (6 m) 78-01031 Adaptor, USB to DB-9, Serial USB to 9-way serial adaptor cable. USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. Page 64 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NGT RM50e HF DATA MODEM PRODUCT TRANSCEIVER PART NO. 08-06978-001 RM50e HF Data Modem DESCRIPTION RM50e HF Data Modem The RM50e is a high performance MIL-spec HF modem designed to connect to the NGT™/Envoy™ family of radios. Compatible with the RM50 in the 2110 series Manpack, this modem provides legacy interoperability with systems running Fixed Frequency and ALE networks operating STANAG 5066 email. The RM50e operates using the most highly advanced Military Standard (MIL-STD) waveforms, including STANAG 4539 and MIL-STD-188-110A/B, providing adaptive rates from 75–9600 bit/s coded. When used in conjunction with an ISB capable NGT™, even higher rates of up to 19200 bit/s are available using MIL-STD-188-110B Appendix F waveforms. COMPATIBILITY: • With NGT™ series and Envoy™ X2 Transceivers NOTE: • For use in ISB mode, an NGT™ SRx Transceiver must be used and fitted with Opt ISB Processor (part number 15-10556-000), see page 35, Opt ISB Processor 2012 (Factory Fit). • ISB mode using the RM50e HF Data modem is not supported when combined with an Envoy X2 transceiver • This product is subject to Australian Government Export Controls. • A signed End-User Declaration must be provided for supply of this product. STANDARD FEATURES: • Compatible with RM50 (2110M Manpack Internal Modem) • MIL-STD Waveforms (MIL-STD-188-110A, MIL-STD-188110B (Inc. Appendix F), STANAG 4285, STANAG 4529, STANAG 4415, STANAG 4539) • ISB capable • Data Encryption (AES-256 bit Algorithm, up to 256 stored keys, Key fill via Codan Key Management Software (KMS)) • MIL-STD-810F Immersion, Dust, Vibration Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 65 Data & Email NGT RM50e HF DATA MODEM CONT. PRODUCT PART NO. TRANSCEIVER DESCRIPTION AVAILABLE OPTIONS: • Support for RC50-C software, see page 59, RC50-C HF Email Software. 08-07167-001 RM50e to NGT™/Envoy™ Transceiver Interface Cable, 1 m 08-07167-006 RM50e to NGT™/Envoy™ Transceiver Interface Cable, 6 m 08-06901-001 Data Interface 19way MIL to USB A Cable 15-04167-EN RM50e HF Data Modem Operator Guide ## denotes language version Page 66 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email NGT 3012 HF DATA MODEM (NO CABLES) PRODUCT MODEM-3012-NC TRANSCEIVER PART NO. DESCRIPTION 3012 HF Data Modem 3012 HF Data Modem (No Cables) (no cables) The 3012 HF Data Modem provides reliable and cost-effective computer text and data communication capabilities for 3012 HF Data Modem (No organisations operating in remote areas with little or no Cables) telecommunications infrastructure. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR Transceivers COMPRISING: 08-05877-004 08-04515-001 30-11208-000 15-04104-CD • • • • 3012 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3012 HF Data Modem User Guide on CDROM (English) STANDARD FEATURES: • Up to 6000 bit/s, error-free data transmission with compression • In-built data compression • Backwards compatible with the Codan 9001/9002 HF Data Modems • Data scrambled for security • In-built serial port optical isolator • Easy to use AT command interface AVAILABLE OPTIONS: • Support for UUPlusTM Email for HF Client or Server software, see page 61, UUPlus Software. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 67 Data & Email 3012 HF DATA MODEM FOR NGT™ WITH 2 M RS232 CABLE PRODUCT MODEM-3012-NGT-2M NGT TRANSCEIVER PART NO. 3012 HF Data Modem for NGT™ with 2 m RS232 Cable DESCRIPTION 3012 HF Data Modem with 2 m RS232 Cable This configuration consists of a 3012 HF Data Modem, 2 m Data Interface Cable, and 1 m NGT™ Junction Box to 3012 Modem Cable. NOTE: This configuration replaces previous part number 08-05877-001. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR Transceivers COMPRISING: Page 68 08-05877-004 08-04515-001 30-11208-000 15-04104-CD • • • • 3012 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3012 HF Data Modem User Guide on CDROM (English) 08-05086-001 Data Interface Cable, 2 m 08-05712-001 NGT™ to 3012 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email 3012 HF DATA MODEM FOR NGT™ WITH 6 M RS232 CABLE PRODUCT MODEM-3012-NGT-6M NGT TRANSCEIVER PART NO. 3012 HF Data Modem for NGTTM with 6 m RS232 Cable DESCRIPTION 3012 HF Data Modem with 6 m RS232 Cable This configuration consists of a 3012 HF Data Modem, 6 m Data Interface Cable, and 1 m NGT™ Junction Box to 3012 Modem Cable. NOTE: This configuration replaces previous part number 08-05877-002. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR Transceivers COMPRISING: 08-05877-004 08-04515-001 30-11208-000 15-04104-CD • • • • 08-05086-006 Data Interface Cable, 6 m 08-05712-001 NGT™ to 3012 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 3012 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3012 HF Data Modem User Guide on CDROM (English) Page 69 Data & Email NGT 3012 ACCESSORIES PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-00136 Cradle, HF Data Modem Vehicle Mounting 78-01031 Adaptor, USB to DB-9, Serial USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. 60-00098-590 Adaptor, 9-pin D PIug to 25-pin D Socket 08-05086-001 08-05086-006 Cable, Data Interface, 2 m Cable, Data Interface, 6 m 08-05712-001 08-05712-006 Cable, NGT™ to 3012 Modem, 1 m Cable, NGT™ to 3012 Modem, 6 m 15-04104-## User Guide, HF Data Modem 3012 Printed User Guide for the 3012 HF Data Modem. 3012 Accessories See page 165, Language Support for translations of this guide. Page 70 08-05980-001 UUPlus™ Email for HF Client Software Single user access to UUPlusTM Email for HF Server Software. For use with the 3012 and 3212 HF Data Modems and embedded 2400 bit/s data mode option offered with Envoy X2 Transceivers. 08-05981-001 UUPlus™ Email for HF Server Software Email server with support for up to 25 remote or local users and Internet email access. For use with the 3012 and 3212 HF Modems and embedded 2400 bit/s data mode option offered with Envoy X2 Transceivers. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email NGT 3212 HF DATA MODEM (NO CABLES) PRODUCT MODEM-3212-NC TRANSCEIVER PART NO. 3212 System Requirements DESCRIPTION 3212 HF Data Modem (No Cables) The 3212 HF Data Modem provides reliable and cost-effective computer text and data communication capabilities for organisations operating in remote areas with little or no telecommunications infrastructure. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. 3212 HF Data Modem (No Cables) COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ X2 Transceivers COMPRISING: 08-06274-001 08-04515-001 30-11208-000 15-04146-CD • • • • 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) STANDARD FEATURES: • Up to 7200 bit/s error free on-air data rate without compression • Backwards compatible with Codan 3012 HF Data Modem • Designed to operate on standard bandwidth commercial HF channels • In-built DC isolation on all available ports • Modem control via RS232 or ethernet port SYSTEM REQUIREMENTS: The following Options are required for operation with the 3212 HF Data Modem: 15-10541-000 15-10469-000 Opt High Speed Data (Factory Fit) (NGT™) Opt Fan (Factory Fit) (NGT™ & Envoy X2™) NOTE: 2.7 kHz Filter is not required for the 3212 HF Data Modem. AVAILABLE OPTIONS: • Support for UUPlus™ Email for HF Client or Server software, see page 61, UUPlus™ Software. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 71 Data & Email 3212 HF DATA MODEM FOR NGT™/ENVOY X2 WITH 2 M RS232 CABLE PRODUCT MODEM-3212-NGT-2M NGT TRANSCEIVER PART NO. 3212 HF Data Modem for NGT™/Envoy™ with 2 m RS232 Cable DESCRIPTION 3212 HF Data Modem with 2 m RS232 Cable This configuration consists of a 3212 HF Data Modem, 2 m Serial Cable, and 1 m Transceiver to 3212 Modem Cable. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. See page 71, 3212 System Requirements for the NGT™/ Envoy X2 Transceiver Options that are required for operation with the 3212 HF Data Modem. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ X2 Transceivers COMPRISING: Page 72 08-06274-001 08-04515-001 30-11208-000 15-04146-CD • • • • 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) 08-06359-002 Serial D9M-D9F Isol Shield Cable, 2 m 08-06356-001 NGT™/Envoy™ X2 to 3212 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email 3212 HF DATA MODEM FOR NGT™/ENVOY™ X2 WITH 6 M RS232 CABLE PRODUCT MODEM-3212-NGT-6M NGT TRANSCEIVER PART NO. 3212 HF Data Modem for NGT™/Envoy™ X2 with 6 m RS232 Cable DESCRIPTION 3212 HF Data Modem with 6 m RS232 Cable This configuration consists of a 3212 HF Data Modem, 6 m Serial Cable, and 1 m NGT™/Envoy™ X2 to 3212 Modem Cable. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. See page 71, 3212 System Requirements for the NGT™/ Envoy™ X2 Transceiver Options that are required for operation with the 3212 HF Data Modem. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ X2 Transceivers COMPRISING: 08-06274-001 08-04515-001 30-11208-000 15-04146-CD • • • • 08-06359-006 Serial D9M-D9F Isol Shield Cable, 6 m 08-06356-006 NGT™/Envoy™ X2 to 3212 Modem Cable, 6 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) Page 73 Data & Email NGT 3212 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 15-00136 DESCRIPTION Cradle, HF Data Modem Vehicle Mounting 3212 Accessories 3212 Accessories Page 74 78-01031 Adaptor, USB to DB-9, Serial USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. 60-00098-590 Adaptor, 9-pin D PIug to 25-pin D Socket 39-79150-080 Ferrite Bead Clamp 08-06359-002 08-06359-006 Cable, Serial D9M-D9F Isol Shield, 2 m Cable, Serial D9M-D9F Isol Shield, 6 m 67-90800 67-90801 Cable, Ethernet Crossover CAT-5E, 2 m Red Cable, Ethernet Crossover CAT-5E, 10 m Red 67-90802 67-90803 Cable, Ethernet Straight CAT-5E, 2 m Blue Cable, Ethernet Straight CAT-5E, 10 m Blue 08-06356-001 08-06356-006 Cable, NGT™/Envoy™ X2 to 3212 Modem, 1 m Cable, NGT™/Envoy™ X2 to 3212 Modem, 6 m 15-04146-EN User Guide, 3212 HF Data Modem (English) Printed User Guide for the 3212 HF Data Modem. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 High Power Amplifiers NGT 3061 500 W POWER AMPLIFIER PRODUCT HIGH-PWR-500 TRANSCEIVER PART NO. 3061 500 W Power Amplifier DESCRIPTION 3061 500 W Power Amplifier A reliable and affordable high power solution for voice and data communication. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ series Transceivers COMPRISING: 08-05974-001 08-06067-001 15-10504 05-06374 08-01503-002 08-05956-001 15-04131-EN 67-90308 • • • • • • • 3061 500 W Power Amplifier 3061 500 W Power Supply Unit Opt External ALC (Retro Fit) (only required for NGT™) Earth Braid, 1.5 m Coaxial Assembly Cable, 2 m High Power Amplifier Controller Cable High Power Amplifiers 3061/3062 Reference Manual (see page 165, Language Support for translations of this guide) • Power IEC Cable, 2 m (for cable options, see page 76, 3061 Accessories) NOTE: • Specify the mains cable (AU, EU, UK or US) at the time of ordering the 3061 Power Amplifier and Power Supply Unit. • The 3061 Power Amplifier is suitable for use with NGT™ SRx, SR, ASR, AR systems, and Envoy™ series Transceivers. • Order Option External ALC (Factory Fit), part number 15-10504-000, when purchasing the power amplifier with an NGTTM Transceiver. • Ensure the antenna used is suitable for 500 W operation. • The Power Amplifier and Power Supply Unit are each 5RU in height and will fit a standard 19" wide rack with depth of 400 mm or greater. STANDARD FEATURES: • • • • • • • • Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 500 W PEP/300 W average output power 100% continuous mode 100–270 V AC 50/60 Hz supply voltage Fully protected against all load conditions Fan forced cooling with thermostatically controlled fans 125 W PEP in bypass mode 19" rack mount (5RU + 5RU) Interface cables for transceiver (coaxial and control cables) Page 75 High Power Amplifiers NGT 3061 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 3061 Accessories 3061 Accessories DESCRIPTION Standard Rack Configurations Standard rack configurations are 27RU free standing 19" rack cabinets. They are supplied preassembled and fitted with a range of mounting trays and panels to suit the equipment as indicated. Radio equipment is packed separately to the rack unit to prevent damage in transit. For rack options, see pages 125 and 126, Standard Rack Configurations. NOTE: This is a typical high power rack configuration. For illustrative purposes only. 67-90305 Cable, 3C Blk Mld IEC AUS, 2 m 67-90306 Cable, 3C Blk Mld IEC UK, 2 m 67-90307 Cable, 3C Blk Mld IEC US, 2 m 67-90308 Cable, 3C Blk Mld IEC EU, 2 m 08-05920-001 Cable, DC Extension, 1 m NOTE: Required for the transceiver when it is rack mounted. 05-06374 Page 76 Earth Braid, 1.5 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 High Power Amplifiers NGT 3062 1 kW POWER AMPLIFIER PRODUCT HIGH-PWR-1000 TRANSCEIVER PART NO. 3062 1 kW Power Amplifier DESCRIPTION 3062 1 kW Power Amplifier A reliable and affordable high power solution for voice and data communication. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ series Transceivers COMPRISING: 08-05975-001 08-06102-001 15-10504 05-06374 08-01503-002 08-05956-001 15-04131-EN 67-90309 • • • • • • • 3062 1 kW Power Amplifier 3062 1 kW Power Supply Unit Opt External ALC (Retro Fit) (only required for NGT™) Earth Braid, 1.5 m Coaxial Assembly Cable, 2 m High Power Amplifier Controller Cable High Power Amplifiers 3061/3062 Reference Manual (see page 165, Language Support for translations of this guide) • Power IEC 320 Cable, 2 m (for cable options, see page 78, 3062 Accessories) NOTE: • Specify the mains cable (AU, EU, UK or US) at the time of ordering the 3062 Power Amplifier and Power Supply Unit. • The 3061 Power Amplifier is suitable for use with NGT™ SRx, SR, ASR, AR systems, and Envoy™ series Transceivers. • Order Option External ALC (Factory Fit), part number 15-10504-000, when purchasing the power amplifier with an NGTTM Transceiver. • Ensure the antenna used is suitable for 1 kW operation. • The Power Amplifier and Power Supply Unit are each 5RU in height and will fit a standard 19" wide rack with depth of 400 mm or greater. STANDARD FEATURES: • • • • • • • • Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 1 kW PEP/600 W average output power 100% continuous mode 100–270 V AC 50/60 Hz supply voltage Fully protected against all load conditions Fan forced cooling with thermostatically controlled fans 125 W PEP in bypass mode 19" rack mount (5RU + 5RU) Interface cables for transceiver (coaxial and control cables) Page 77 High Power Amplifiers NGT 3062 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 3062 Accessories 3062 Accessories DESCRIPTION Standard Rack Configurations Standard rack configurations are 27RU free standing 19" rack cabinets. They are supplied preassembled and fitted with a range of mounting trays and panels to suit the equipment as indicated. Radio equipment is packed separately to the rack unit to prevent damage in transit. For rack options, see pages 125 and 126, Standard Rack Configurations. NOTE: This is a typical high power rack configuration. For illustrative purposes only. 67-90309 Cable, 3C Blk Mld IEC 320-UK, 2 m NOTE: This is the only mains cable available for use with the 3062 1 kW Power Amplifier. If required for use in countries other than the UK, the cable will need to be reterminated accordingly. 08-05920-001 Cable, DC Extension, 1 m NOTE: Required for the transceiver when it is rack mounted. 05-06374 Page 78 Earth Braid, 1.5 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Crosspatch™/Phone/GPS Solutions NGT CROSSPATCH™ FOR NGT™/ENVOY™ PRODUCT XPATCH-NGT TRANSCEIVER PART NO. Crosspatch™ for NGT™/ Envoy™ DESCRIPTION 3031 Crosspatch™ Codan’s leading edge 3031 CrosspatchTM enables you to carry ‘HF on your belt’ using a VHF/UHF radio and a Codan NGT™/Envoy™ Transceiver. It is the practical, effective and™ affordable solution for any organisation that needs to extend their current HF or VHF/UHF networks. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ X2 Transceivers COMPRISING: 08-06730-001 08-06766-001 15-04148-CD 06-02489-EN 15-00145 • • • • • 3031 VHF/UHF to HF Crosspatch™ for NGT™/Envoy™ 3031 to VHF/UHF Transceiver Generic Cable, 2 m CrosspatchTM 3031 CD Package (English) CrosspatchTM 3031 Quick Reference Cards, English (x2) CrosspatchTM 3031 Installation Kit NGT CROSSPATCH™ ACCESSORIES PRODUCT TRANSCEIVER PART NO. 08-06766-001 DESCRIPTION Cable, 3031 to VHF/UHF Transceiver Generic Crosspatch™ Accessories 06-02489-EN Quick Reference Card, Crosspatch™ 3031 15-04148-EN User Guide, Crosspatch™ 3031 (English) Printed User Guide for the 3031 Crosspatch™. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 79 Crosspatch™/Phone/GPS Solutions NGT 3033 TELEPHONE INTERCONNECT PRODUCT RTI-3033-NGT TRANSCEIVER PART NO. 3033 Telephone Interconnect DESCRIPTION 3033 Telephone Interconnect Codan’s telephone interconnect equipment can link into the telephone system enabling you to make or receive telephone calls on your HF transceiver. Comes with all cables and Reference Manual. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ X2 Transceivers COMPRISING: 08-06797-001 08-06820-001 08-06819-001 15-04156-CD • • • • 3033 Telephone Interconnect 3033 to Transceiver Interface Cable 3033 to 3020 Power Supply Cable 3033 Telephone Interconnect User Guide on CD (English) STANDARD FEATURES: • • • • • • • Fully automated and intuitive operation Multilingual voice prompts Flexible configuration and remote management Worldwide compliance (Telephone and EMC) Radio user can access public telephone network Telephone users can contact radio users Designed for extreme conditions ADDITIONAL FEATURES AVAILABLE THROUGH ATTACHED NGT™ TRANSCEIVER: • Choice of pre-programmed telephone numbers or free dialling • Accessible for user with only selective calling capability (non-telcall users) • Access control to restrict access to individual users, groups of users, and the number of digits that can be dialled Page 80 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Crosspatch™/Phone/GPS Solutions NGT 3033 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 08-04146-001 DESCRIPTION Cable, 6-way Phone 3033 Accessories 08-04515-001 Earth Wire, 0.5 m 67-90800 Cable, Ethernet Crossover CAT-5E, 2 m Red 67-90801 Cable, Ethernet Crossover CAT-5E, 10 m Red 67-90802 Cable, Ethernet Straight CAT-5E, 2 m Blue 67-90803 Cable, Ethernet Straight CAT-5E, 10 m Blue 15-04156-EN User Guide, 3033 Telephone Interconnect (English) Printed User Guide for the 3033 Telephone Interconnect. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 81 Crosspatch™/Phone/GPS Solutions NGT GPS TRACKING SOFTWARE PRODUCT TRANSCEIVER PART NO. GPS Tracking Software DESCRIPTION InterNav-CHF GPS Tracking Software The InterNav-CHF GPS Tracking Software is a computerised map positioning system for up to 100 users. It requires a Windows™ 2000/XP/Vista/WIN7 operating system. Includes: software, user manual and hardware security dongle NOTE: Interface cable must be ordered separately. COMPATIBILITY: • With NGT™ SRx, SR, ASR, AR and Envoy™ series Transceivers 78-07003-990 78-07003-010 78-07003-025 78-07003-050 78-07003-100 InterNav-CHF™ GPS Tracking Software – 1 User (Dealer) InterNav-CHF™ GPS Tracking Software – 10 User InterNav-CHF™ GPS Tracking Software – 25 User InterNav-CHF™ GPS Tracking Software – 50 User InterNav-CHF™ GPS Tracking Software – 100 User Setup Three day on-site installation, commissioning and training visit by a Codan engineer. 78-07004 GPS, Map scanning per A4 page Includes: Scanning and registration of maps, chart purchase and copyright fee SPECIFY: • Geographic areas to be mapped • Scale(s) required NGT GPS ACCESSORIES PRODUCT TRANSCEIVER PART NO. 08-05086-001 GPS Accessories DESCRIPTION Cable, Data Interface, 2 m Interface cable for computer control via CICS or GPS Tracking software, and NGT™ Transceivers that have a junction box. Cable connects to 9 pin serial port on NGT™ Junction Box. COMPATIBILITY: • With NGT™ SR, ASR, AR and Envoy™ series Transceivers 08-06380-001 Cable, Serial 6-way to D9F Interface cable for computer control via CICS or GPS Tracking software and security key programming using KMS/KFS on the NGT™ SRx and Envoy™ series Transceivers. Cable connects to 6-pin serial port on NGT™/Envoy™ RF Unit. COMPATIBILITY: • With NGT™ SRx, AR Voice and Envoy™ series Transceivers Page 82 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Supplies NGT 3020 TRANSCEIVER SUPPLY PRODUCT TRANSCEIVER PART NO. 78-20022 3020 Transceiver Supply 3020 Transceiver Supply DESCRIPTION 3020 Transceiver Supply Designed for environments with unreliable and fluctuating mains systems. Suitable for use with either voice or data stations. Nominal input: 100 to 240 V AC ±10% (50/60 Hz) Nominal output: 13.8 V DC, 16 A continuous, 20 A peak Mains connection: IEC socket on rear of unit COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers 67-90305 Cable, 3C Blk Mld IEC AUS, 2 m 67-90306 Cable, 3C Blk Mld IEC UK, 2 m 67-90307 Cable, 3C Blk Mld IEC US, 2 m 67-90308 Cable, 3C Blk Mld IEC EU, 2 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 83 Transceiver Supplies NGT 3020 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 15-00702 3020 Accessories DESCRIPTION Cable Kit for Float Charge Cable kit for float charging lead-acid storage battery for uninterrupted supply. 3020 Accessories 15-00175 3RU Rack-mounting Frame for 3020 NOTE: For additional racking accessories, see page 125, 19" Racks & Accessories. NGT DC-DC VOLTAGE CONVERTER PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-00508 Voltage Regulator (24 V to 12 V operation 20 A) Enables the operation of NGT™ and Envoy™ series DC-DC Voltage Converter Transceivers in 24 V based systems. Protected from faults such as voltage spikes, overload, short circuits and low voltage input. The unit automatically resets once a fault is detected. Nominal Input: 24 V DC Nominal Output: 12 V @20 A Efficiency: Greater than 90% at full load Page 84 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Transceiver Supplies NGT SOLAR POWER SUPPLIES PRODUCT TRANSCEIVER PART NO. 15-00531 Solar Power Supplies DESCRIPTION Solar Power Supply 40 W Recommended for voice (light duty). COMPRISING: • • • • • 15-00532 Single 40 W solar panel Mounting frame complete with anti-bird spikes Solar battery regulator Heavy duty twin core cable Battery lugs Solar Power Supply 80 W Recommended for voice (heavy duty). COMPRISING: • • • • • 15-00533 Single 80 W solar panel Mounting frame complete with anti-bird spikes Solar battery regulator Heavy duty twin core cable Battery lugs Solar Power Supply 240 W Recommended for fax and data (heavy duty). COMPRISING: • • • • • Three 80 W solar panels Mounting frame complete with anti-bird spikes Solar battery regulator Heavy duty twin core cable Battery lugs NGT SOLAR POWER SUPPLY ACCESSORIES PRODUCT PART NO. 08-05399-001 TRANSCEIVER DESCRIPTION Cable, Battery Paralleling (+ve) Solar Power Supply Accessories 08-05399-002 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Cable, Battery Parallelling (–ve) Page 85 Transceiver Supplies BATTERIES Batteries PRODUCT PART NO. 65-72000-012 Batteries NGT TRANSCEIVER DESCRIPTION Battery, Lead acid 12 V 90Ah (supplied dry charged) NOTE: This battery is classified as dangerous goods and requires a special permit to air freight. 65-72003 Battery, 12 V 100Ah Gelcell NOTE: This battery can be air freighted without a permit. 65-72004 Battery, 12 V 185Ah Gelcell NOTE: This battery can be air freighted without a permit. Page 86 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT 3040 AUTOMATIC TUNING WHIP PRODUCT ANT-3040-NC TRANSCEIVER PART NO. 3040 Automatic Tuning Whip (No Cables) DESCRIPTION 3040 Automatic Tuning Whip (No Cables) The 3040 Automatic Whip Antenna is a low profile, rugged, lightweight unit designed for mobile installations. It provides 3040 Automatic fast automated tuning across the HF band. Tuning Whip Antenna The 3040 is easy to install and meets MIL-STD-810F for shock, immersion, dust and vibration. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-07007-001 08-07148-001 78-18058 78-23085 78-23086 15-60012 • • • • • • 3040 Main Assembly 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit STANDARD FEATURES: • • • • 2.5 to 30 MHz 125W PEP voice or data Fast tuning typically < 1sec Tune from memory AVAILABLE ACCESSORIES: See page 89, 3040 Accessories for cables and other parts used with the 3040. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 87 Antennas 3040 AUTOMATIC TUNING WHIP WITH 6 M CABLES PRODUCT ANT-3040-6M NGT TRANSCEIVER PART NO. 3040 Automatic Tuning Whip Antenna with 6 m Cables DESCRIPTION 3040 Automatic Tuning Whip with 6 m Cables The 3040 Automatic Whip Antenna is a low profile, rugged, lightweight unit designed for mobile installations. It provides fast automated tuning across the HF band. 3040 Automatic Tuning Whip Antenna The 3040 is easy to install and meets MIL-STD-810F for shock, immersion, dust and vibration. NOTE: Supplied with 6 m cables to connect the 3040 Antenna to an NGT™/Envoy™ Transceiver. See page 89, 3040 Accessories for additional 3040 accessories. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 • • • • • • • • 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.65 m 3040 Automatic Whip Antenna Installation Handbook, c/w antenna connector sealing kit STANDARD FEATURES: • • • • 2.5 to 30 MHz 125 W PEP voice or data Fast tuning typically < 1sec Tune from memory AVAILABLE ACCESSORIES: See page 89, 3040 Accessories for cables and other parts used with the 3040. Page 88 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT 3040 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 08-07148-001 3040 Accessories 3040 Accessories DESCRIPTION 3040 Spring Flexible mounting for whip antennas. The spring is highly recommended when using the fibreglass whip and/or riser. 78-23086 3040 Stainless Steel Whip A stainless steel whip offered as a more flexible and less visually obstructive alternative to the fibreglass version. The whip is 1.65 m in length. 78-23085 3040 Fibreglass Whip This is a 1.6 m fibreglass whip and is recommended to be used with the spring and the riser section. In this configuration the antenna will operate over a transmit frequency range of 2.5 to 30 MHz. 78-18058 Riser, Fibreglass A 0.8 m fibreglass section used to extend the overall length of the antenna element when using the 1.6 m fibreglass or stainless steel whips to achieve maximum possible frequency range (2.5 to 30 MHz) and radiation performance. 78-14010 3040/3042 NVIS Antenna Kit Suits the 3040 Automatic Tuning Whip Antenna/3042 Antenna Tuner for improved short range (0 to 500 km) near vertical incidence skywave communications mode over frequency range 2 to 12 MHz. Includes: 2 section lightweight NVIS whip antenna sections, tie down cord kit, instruction card and canvas storage bag. 08-05627-002 08-05627-006 08-05627-010 08-05627-020 Cable, Control NGT/Envoy to 9350/304X, 2m Cable, Control NGT/Envoy to 9350/304X, 6 m Cable, Control NGT/Envoy to 9350/304X, 10 m Cable, Control NGT/Envoy to 9350/304X, 20 m 08-01503-006 08-01503-008 08-01503-020 08-01503-030 Cable, Coax Assembly, UHF Type Connectors, RG58, 6 m Cable, Coax Assembly, UHF Type Connectors, RG58, 8 m Cable, Coax Assembly, UHF Type Connectors, RG58, 20 m Cable, Coax Assembly, UHF Type Connectors, RG58, 30 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 89 Antennas NGT 9350 AUTOMATIC TUNING WHIP PRODUCT ANT-9350-NC TRANSCEIVER PART NO. DESCRIPTION 9350 Automatic Tuning Whip (No Cables) 9350 Automatic Tuning Whip (No Cables) 9350 Automatic Tuning Whip Antenna A robust antenna designed for mobile installations requiring flexible, high performance HF communications. It provides fast automated tuning over the entire HF frequency range. The 9350 is easy to install, and meets MIL-STD-810F for shock and vibration. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-05063-001 08-05140-001 78-23007-003 78-23025 15-04142-## • • • • • 9350 Main Assembly 9350 Spring 9350 Fibreglass Whip, 1.6 m 9350 Tapered Stainless Steel Whip, 1.2 m Automatic Tuning Whip Antenna 9350 Installation Handbook (see page 165, Language Support for translations of this handbook) STANDARD FEATURES: • 125 W PEP voice or data • Tuning time typically 2 seconds • Transmit frequency range 2 to 30 MHz depending on antenna • Receive frequency range 250 kHz to 30 MHz AVAILABLE ACCESSORIES: See page 92, 9350 Accessories for cables to connect the 9350 Antenna to an NGT™ or Envoy™ Transceiver. ## denotes language version Page 90 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas 9350 AUTOMATIC TUNING WHIP WITH 6 M CABLES PRODUCT ANT-9350-6M NGT TRANSCEIVER PART NO. 9350 Automatic Tuning Whip Antenna with 6 m Cables 9350 Automatic Tuning Whip Antenna DESCRIPTION 9350 Automatic Tuning Whip with 6 m Cables A robust antenna designed for mobile installations requiring flexible, high performance HF communications. It provides fast automated tuning over the HF range. The 9350 is easy to install, and meets MIL-STD-810F for shock and vibration. NOTE: Supplied with 6 m cables to connect the 9350 Antenna to an NGT™/Envoy™ Transceiver, see page 92 for additional 9350 accessories. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-05063-001 08-05627-006 08-01503-006 08-05140-001 78-23007-003 78-23025 15-04142-## • • • • • • • 9350 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 9350 Spring 9350 Fibreglass Whip, 1.6 m 9350 Tapered Stainless Steel Whip, 1.2 m Automatic Tuning Whip Antenna 9350 Installation Handbook (see page 165, Language Support for translations of this handbook) STANDARD FEATURES: • 125 W PEP voice or data • Tuning typically 2 seconds • Transmit frequency range 2 to 30 MHz depending on antenna • Receive frequency range 250 kHz to 30 MHz ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 91 Antennas NGT 9350 ACCESSORIES PRODUCT TRANSCEIVER PART NO. 08-05140-001 9350 Accessories 78-23007-003 DESCRIPTION 9350 Spring Strain relief for 9350 Fibreglass Whip. 9350 Accessories 9350 Fibreglass Whip, 1.6 m This is the primary whip normally supplied with the 9350. It is a copper wire encased in a polyurethane covered fibreglass rod. The whip is designed to withstand substantial flexing and rugged conditions. It operates over the transmit frequency range of 2 to 30 MHz. NOTE: Must be used with the spring (part number 08-05140-001). 78-23056 9350 Tapered Stainless Steel Whip, 1.65 m This whip enables use over the transmit frequency range of 2 to 30 MHz and provides a more flexible and less visible alternative to the fibreglass whip. NOTE: Can be used without the spring (part number 08-05140-001). 78-23025 9350 Tapered Stainless Steel Whip, 1.2 m This whip is designed as an emergency backup to the primary whip (part number 78-23007-003) in case of damage. It is only suitable for operation over a transmit frequency range of 2.5 to 30 MHz and is less efficient than the primary whip. NOTE: Can be used without the spring (part number 08-05140-001). 15-00323 NVIS Antenna Kit Suits the 9350 Automatic Tuning Whip Antenna for improved short range (0 to 500 km) near vertical incidence skywave (NVIS) communications over frequency range 2 to 12 MHz. Includes: two piece whip antenna, angle adaptor, extension riser, tie down cord kit and fitting instructions in a canvas bag Page 92 08-05627-006 08-05627-008 08-05627-030 Cable, Control NGT/Envoy to 9350/304X, 6 m Cable, Control NGT/Envoy to 9350/304X, 8 m Cable, Control NGT/Envoy to 9350/304X, 30 m 08-01503-006 08-01503-008 08-01503-020 08-01503-030 Cable, Coax Assembly, UHF Type Connectors, RG58, 6 m Cable, Coax Assembly, UHF Type Connectors, RG58, 8 m Cable, Coax Assembly, UHF Type Connectors, RG58, 20 m Cable, Coax Assembly, UHF Type Connectors, RG58, 30 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT 3042 HF ANTENNA TUNER PRODUCT ANT-3042-NC TRANSCEIVER PART NO. 3042 HF Antenna Tuner (No Cables) DESCRIPTION 3042 HF Antenna Tuner (No Cables) The 3042 is a low profile, 125 W HF antenna tuning unit designed to deliver high performance and reliability in the world’s harshest environments. It provides high speed and efficient tuning of short whip antennas across the full operational HF band. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-07154-001 15-00146 15-04174-EN • 3042 HF Antenna Tuner • Installation Kit • 3042 Automatic Antenna Tuner Installation Handbook STANDARD FEATURES: • • • • • • • • • • • 2 to 30 MHz 125 W RF power handling Fast tuning typically < 1sec High efficiency Waterproof MIL-STD-810G Environmentals N-type RF Connector Used with Vertical & NVIS Whip Antennas Flexible mounting ALE compatible Internal receive mode amplifier AVAILABLE ACCESSORIES: See page 95, 3042 Accessories for cables and other parts used with the 3042. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 93 Antennas NGT 3042 HF ANTENNA TUNER WITH 6 M CABLES PRODUCT ANT-3042-6M TRANSCEIVER PART NO. 3042 HF Antenna Tuner with 6 m Cables DESCRIPTION 3042 HF Antenna Tuner with 6 m Cables The 3042 is a low profile, 125 W HF antenna tuning unit designed to deliver high performance and reliability in the world’s harshest environments. It provides high speed and efficient tuning of short whip antennas across the full operational HF band. NOTE: Supplied with 6 m cables to connect the tuner to the antenna. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-07154-001 08-05627-006 08-05837-006 15-00146 15-04174-EN • 3042 HF Antenna Tuner • Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m • Coax Assembly Cable with UHF to N-type Connectors, RG58, 6 m • Installation Kit • 3042 Automatic Antenna Tuner Installation Handbook STANDARD FEATURES: • • • • • • • • • • • 2 to 30 MHz 125 W RF power handling Fast tuning typically < 1sec High efficiency Waterproof MIL-STD-810G Environmentals N-type RF Connector Used with Vertical & NVIS Whip Antennas Flexible mounting ALE compatible Internal receive mode amplifier AVAILABLE ACCESSORIES: See page 95, 3042 Accessories for cables and other parts used with the 3042. Page 94 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT 3042 ACCESSORIES PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-60020 Single Hole Mount Base The single hole mount antenna base is designed for lighter duty installations, and provides the convenience of a small footprint requiring only a single 14 mm mounting hole. 15-60021 3042 Accessories Flange Mount Base The flange mount antenna base is designed to provide a sturdy antenna mount for installations requiring the high voltage feed line to pass through a vehicle panel. Flange mount includes rubber gasket and mounting hardware. 3042 Accessories 15-60022 Flange Mount Bracket The flange mount bracket provides external side mounting of the flange mount antenna base. Mounting fasteners must be provided separately. 08-07148-001 3042 Spring Flexible mounting for whip antennas. The spring is highly recommended when using the fibreglass whip and/or riser. 15-60023 3042 Shock Mount The shock mount for the 3042 Antenna Tuner is recommended for installations likely to experience extreme levels of vibration or shock. The mount features quick fit/ release fasteners that require no tools to use. Fitting instructions are supplied, and an installation kit that will suit most applications. 78-23086 3042 Stainless Steel Whip A stainless steel whip offered as a more flexible and less visually obstructive alternative to the fibreglass version. The whip is 1.65 m in length. 78-23085 3042 Fibreglass Whip This is a 1.6 m fibreglass whip and is recommended to be used with the spring and the riser section. In this configuration the antenna will operate over a transmit frequency range of 2.5 to 30 MHz. 78-18058 Riser, Fibreglass A 0.8 m fibreglass section used to extend the overall length of the antenna element when using the 1.6 m fibreglass or stainless steel whips to achieve maximum possible frequency range (2 to 30 MHz) and radiation performance. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 95 Antennas NGT 3042 ACCESSORIES CONT. PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-00146 Installation Kit Kit containing a selection of fasteners for mounting the 3042 Antenna Tuner. 78-14010 3040/3042 NVIS Antenna Kit Suits the 3040 Automatic Tuning Whip Antenna/3042 Antenna Tuner for improved short range (0 to 500 km) near vertical incidence skywave communications mode over frequency range 2 to 12 MHz. Includes: 2 section lightweight NVIS whip antenna sections, tie down cord kit, instruction card and canvas storage bag. Page 96 08-05627-002 08-05627-006 08-05627-010 08-05627-020 Cable, Control NGT/Envoy to 9350/304X, 2m Cable, Control NGT/Envoy to 9350/304X, 6 m Cable, Control NGT/Envoy to 9350/304X, 10 m Cable, Control NGT/Envoy to 9350/304X, 20 m 08-05837-002 08-05837-006 08-05837-010 08-05837-020 Cable, Coax Assembly, UHF to N-type Connectors, RG58, 2 m Cable, Coax Assembly UHF to N-type Connectors, RG58, 6 m Cable, Coax Assembly UHF to N-type Connectors, RG58, 10 m Cable, Coax Assembly UHF to N-type Connectors, RG58, 20 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas TUNERS Tuners PRODUCT PART NO. NGT TRANSCEIVER 08-04835-013 DESCRIPTION Tuner, 9103 Automatic Antenna with 10 m Cables Designed to suit NGT™/Envoy™ Transceivers. Rated to 150 W PEP voice or data. Includes: mounting bracket, control cable (10 m) to suit NGTTM Transceiver, coaxial cable (10 m) and installation/operation handbook Tuners 08-04835-015 Tuner, 9103 Automatic Antenna with 30 m Cables Designed to suit NGT™/Envoy™ series Transceivers. Rated to 150 W PEP voice or data. Includes: mounting bracket, control cable (30 m) to suit NGTTM Transceiver, coaxial cable (30 m) and installation/operation handbook 08-06739-001 Tuner, SG235C 500 W PEP Designed to suit 500 W high power NGT™/Envoy™ systems. Includes: mounting bracket and installation/operation handbook NOTE: • Maximum power input in data mode 300 W average. • Control and coaxial cables are not supplied. For the control cable, see Tuner Accessories below. For coaxial cables, see page 109, Coaxial Cables. TUNER ACCESSORIES PRODUCT NGT Tuner Accessories PART NO. 30-37601-002 Tuner Accessories TRANSCEIVER DESCRIPTION Copper Earth Strip 50 mm x 0.46 mm (26 gauge) supplied in units of 1 m 08-06740-030 Cable, SG235C Control, 30 m 08-01503-030 Cable SG235C Coax Assembly, UHF type connectors, RG58, 30 m NOTE: For coaxial cables, see page 109, Coaxial Cables. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 97 Antennas NGT BASE WHIP PRODUCT TRANSCEIVER PART NO. Base Whip Antenna DESCRIPTION The Base Whip Antenna is 9.5 m (31 ft) in height, and requires an automatic antenna tuner. It is mounted vertically on a suitable ground plane or metal roof. An earth mat may be required where a suitable ground plane cannot be found. This antenna may be used where space is restricted and omnidirectional coverage is required. Antenna rated to 500 W PEP. See page 97, Tuners for available tuner options. 15-00406-001 Ant, Base Whip, Ground Mounting (9.5 m/31 ft Unloaded) Comes complete with ground mounting plate, guy kit and guy clamps, guy anchors, HV lead and installation instructions. NOTE: • Coaxial cable and tuner are not supplied. • May require radial ground plane for ground installations. • Compatible with 9103 and SG235C Antenna tuners, see page 96 for more details on tuners • Guying details: One guy set with four guy wires. 4 m guy radius. • Guy anchor points not supplied. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. 15-00406-002 Ant, Base Whip, Roof Mounting (9.5 m/31 ft Unloaded) Comes complete with roof mounting bracket, guy kit and guy clamps, HV lead and installation instructions. NOTE: • Coaxial cable and tuner are not supplied. • Compatible with 9103 and SG235C Antenna tuners, see page 96 for more details on tuners • Requires radial ground plane for non-metallic roof installations. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. • Guying details: One guy set with four guy wires. 4 m guy radius. NGT BASE WHIP ACCESSORIES PRODUCT TRANSCEIVER PART NO. 15-00158 Earth Mat for Base Whip Antenna, Ground Installations 15-00159 Radial Ground Plane for Base Whip Antenna, Roof Installations Base Whip Accessories Page 98 DESCRIPTION Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas TUNED LONG WIRE PRODUCT NGT Tuned Long Wire Antenna PART NO. 15-00403 TRANSCEIVER DESCRIPTION Ant, Tuned Long Wire (2–30 MHz) This antenna exhibits a good combination of space efficiency and broadband capability. It is designed to be used with an antenna tuner. A suitable antenna where space is limited. The Long Wire antenna may be deployed in a sloping wire or Inverted-L configuration. NOTE: • Compatible with 9103 and SG235C Antenna tuners, see page 96 for more details on tuners. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. • When installed as an Inverted-L configuration the minimum recommended height is 6 m. • When installed as a sloping long wire the minimum height at the high end should be 6 m but can be as high as 15 m COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 99 Antennas 3048 TUNED DIPOLE PRODUCT NGT Tuned Long Wire Antenna TRANSCEIVER PART NO. ANT-3048-20M DESCRIPTION 3048 Tuned Dipole Antenna with 20 m cables The 3048 Tuned Dipole is an HF antenna solution designed for base station use. When compared to wire broadband antennas the 3048 has a significantly reduced installed footprint, which is a benefit for installations where space is restricted. The 3048 antenna system comprises a main tuner unit and 4 element antenna assembly mounted on top of a 6 m mast. A control cable and coaxial cable run down from the tuner unit to an interface box mounted at the base of the mast. The interface box provides connection points for the transceiver antenna control and RF cables as well as the RF ground. NOTE: • Interface box coaxial connection uses a UHF type RF connector • 6 m mast uses two guys sets, each with 4 guy wires and guy radius of 4 m • Maximum recommended control cable length between the interface box and transceiver is 20 m • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers COMPRISING: 08-07324-001 15-04185-EN 78-13038 08-01503-020 08-05627-020 • • • • • Antenna, Tuned Diopole, 3048 3048 Tuned Dipole Installation Handbook 6 m guyed mast for 3048 Tuned Dipole Coax assembly cable with UHF connectors, RG58, 20 m Control NGT/Envoy to 9350/304X Cable, 20 m FEATURES: • • • • • • • • • Page 100 2.5-30 MHz 125 W power handling (voice and data) Fast tune typically <1 sec Unlimited memory tune High efficiency Waterproof Designed to MIL-STD-810G Internal receive mode amplifier Small installed footprint Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT TRAVELLING WAVE DIPOLE PRODUCT TRANSCEIVER PART NO. Travelling Wave Dipole Antenna DESCRIPTION The Travelling Wave Dipole Antenna is efficient for short to medium distance communications. Its radiation patterns are generally omni-directional, resulting in a consistent coverage over the frequency range. Designed for 100% duty cycle voice and data operation at the rated power level. This antenna requires a substantial cleared area at ground level for installation, and is more suitable for permanent fixed site installations. Refer to the antenna data sheet for more details. Includes: pulleys, halyards and installation hardware NOTE: • Recommended mast for the 53 m antenna variants is the 15-00422-015, 15 m guyed mast. For further information on masts see page 107, Antenna Masts. • Recommended mast for the 40 m variants is the 15-00422012, 12 m guyed mast • Coaxial cable and masts not supplied. For coaxial cables, see page 109, Coaxial Cables. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. • Antenna lengths quoted are required mast to mast distances. • Antenna is fitted with UHF type RF connector. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers 78-01248 Ant, Travelling Wave Dipole (2–30 MHz, 125 W PEP), 53 m 78-01249 Ant, Travelling Wave Dipole (3–30 MHz, 125 W PEP), 40 m 78-01250 Ant, Travelling Wave Dipole (2–30 MHz, 1000 W PEP), 53 m 78-01251 Ant, Travelling Wave Dipole (3–30 MHz, 1000 W PEP), 40 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 101 Antennas NGT DELTA PRODUCT TRANSCEIVER PART NO. Delta Antenna DESCRIPTION The Delta Antenna is a high performance, omni-directional broadband antenna that performs well over very short to medium distances. Designed for 100% duty cycle voice and data operation at the rated power level. This antenna requires a substantial cleared area at ground level for installation, and is more suitable for permanent fixed site installations. Refer to the antenna data sheet for more details. NOTE: • Recommended mast is 15-00422-015, 15 m guyed mast. For further information on masts see page 107, Antenna Masts. • Distance between antenna guy anchors is 46 m. • Antenna is fitted with UHF type RF connector. • The Delta Antenna is not recommended for rooftop installations. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. • Coaxial cable and mast not supplied. For coaxial cables, see page 109, Coaxial Cables. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers Page 102 78-01022 Ant, Full Delta (3–30 MHz, 125 W) 78-01247 Ant, Full Delta (3 –30 MHz, 1000 W PEP) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT SEMI-DELTA PRODUCT TRANSCEIVER PART NO. Semi-delta Antenna DESCRIPTION The Semi-delta Antenna is a high performance, omnidirectional broadband antenna that performs well over short to medium distances. This antenna requires a large cleared area at ground level for installation, and is more suitable for permanent fixed site installations. NOTE: • Recommended mast is 15-00422-015, 15 m guyed mast however the 15-00422-012 12 m guyed mast may also be used. Using the 12 m mast will increase the required distance between the main mast and stub mast. Recommended stub mast height is 2 m. For further information on masts see page 107, Antenna Masts. • Distance between main mast and stub mast is 20 m with 15 m main mast and 24 m with 12 m main mast. • Antenna is fitted with UHF type RF connector. • An antenna counterpoise/ground is required when mounted on non-metallic roofs or the ground where soil conductivity conditions are very poor. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. • Coaxial cable and masts not supplied. For coaxial cables, see page 109, Coaxial Cables. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers 78-01012 Ant, Semi-delta (2–14 MHz, 125 W PEP) Includes: pulleys, halyards, basic installation hardware, and installation instructions 78-01246 Ant, Semi-delta (2–14 MHz, 1000 W PEP) Includes: pulleys, halyards, basic installation hardware, and installation instructions Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 103 Antennas NGT TFD411 BROADBAND PRODUCT TRANSCEIVER PART NO. TFD411 Broadband Antenna DESCRIPTION The Code 411 TFD is a 2-wire terminated folded dipole antenna designed for broadband operation. Designed for 100% duty cycle voice and data operation at the rated power level. The antenna is easy to install and can be mounted horizontally between two support systems, or as an inverted V using a single central support mast. A large cleared area at ground level is required for installation. Refer to the antenna data sheet for more details. Includes: stainless steel antenna wiring, pulleys, rope, halyard, UHF coaxial connector and installation instructions NOTE: • Recommended mast for the 27 m and 34 m variants of this antenna for horizontal and inverted V configurations is the 10 m Premium Mast (15-60033 or 15-60034). • The masthead gibbet (15-60035) is also required if installing the 27 m and 34 m variants of these antennas on the 10 m mast as inverted V. • Recommended mast for the 43 m variant of this antenna for horizontal and inverted V configurations is the 12 m Mast (15-00422-012). • For further information on masts see page 107, Antenna Masts. • Always select the longest antenna variant possible to maximise propagation efficiency and performance. • Antenna is fitted with UHF type RF connector. • Coaxial cable and masts not supplied. For coaxial cables, see page 109, Coaxial Cables. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers Page 104 15-00411-005 Ant, TFD411, 125 W, 2–30 MHz, 27 m 15-00411-004 Ant, TFD411, 125 W, 2–30 MHz, 34 m 15-00411-003 Ant, TFD411, 125 W, 2–30 MHz, 43 m 15-00411-011 Ant, TFD411, 1000 W, 2–30 MHz, 34 m 15-00411-012 Ant, TFD411, 1000 W, 2–30 MHz, 43 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT TFD411 BROADBAND TRANSCEIVER Horizontal Mounting Inverted ‘V’ Mounting Length Part Numbers Dimensions (m) a b c d e f g 43 m 15-00411-003 / 012 12 47 12.5 2 20 22 2 34 m 15-00411-004 / 011 10 37 10.5 2 16 18 2 27 m 15-00411-005 10 30 10.5 2 11.7 13.7 2 NOTE: • Antenna installation dimensions for inverted V assume stub mast heights of 2 m with guy radius of 2 m • Installation dimensions assume level surface and may vary with sloping or irregular sites • Mast height (c) for inverted V mounting assumes a masthead gibbet which effectively increases the mast height by 0.5 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 105 Antennas NGT TFD411 BROADBAND/MAST KITS PRODUCT PART NO. TFD411 Broadband/Mast Kits TRANSCEIVER DESCRIPTION The Terminated Folded Dipole 411 Antenna and Mast Kit provides an easy to deploy and economical antenna solution for 125 W base station applications. The kits are available with different mast finishes and antenna lengths to meet customer requirements. The kits are designed for inverted V antenna configuration to minimise installation footprint and optimise short to medium distance HF communications. NOTE: • The 10 m premium guyed mast is included as part of this antenna. For further information on masts see page 107, Antenna Masts. • Always select the longest antenna variant possible to maximise propagation efficiency and performance. • Antennas are fitted with a UHF type RF connector. • Coaxial cable is not supplied. For coaxial cables, see page 109, Coaxial Cables. • Lightning protection is recommended for fixed base station installations, see page 110, Lightning Protection. COMPATIBILITY: • With ALL NGT™ and Envoy™ series Transceivers Antenna/Mast — Mast Bare Aluminium Finish 15-60018-005 Ant, TFD411, 125 W, 2–30 MHz, 27 m c/w Lightweight Premium Mast, 10 m 15-60018-004 Ant, TFD411, 125 W, 2–30 MHz, 34 m c/w Lightweight Premium Mast, 10 m 15-60018-003 Ant, TFD411, 125 W, 2–30 MHz, 43 m c/w Lightweight Premium Mast, 10 m Antenna/Mast — Mast Matt Black Paint Finish Page 106 15-60018-105 Ant, TFD411, 125 W, 2–30 MHz, 27 m c/w Lightweight Premium Black Painted Mast, 10 m 15-60018-104 Ant, TFD411, 125 W, 2–30 MHz, 34 m c/w Lightweight Premium Black Painted Mast, 10 m 15-60018-103 Ant, TFD411, 125 W, 2–30 MHz, 43 m c/w Lightweight Premium Black Painted Mast, 10 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas ANTENNA MASTS PRODUCT NGT Antenna Masts PART NO. 15-00422-012 Antenna Masts TRANSCEIVER DESCRIPTION Mast, Guyed 12 m with Erection Kit Four section 12 m mast. Guyed tubular aluminium mast with ground plate, halyard pulley, RF transparent guy kit, full erection kit, mast head gibbet and erection instructions. Designed to withstand wind speeds up to 144 kph (40 m/s) in clear air with head loads up to 12 kg, subject to ground anchoring. NOTE: • Guying details: Four guy sets, each with four guy wires. 6 m guy radius. • Mast suitable for air freight. COMPATIBILITY: • Compatible with Tuned Long Wire (15-00403), Travelling Wave Dipole (78-01248, 78-01249, 78-01250), Semi Delta (78-01012 and 78-01246) TFD411 (15-00411-0XX series). Check antenna section for specific details of antennas see page 97. 15-00422-015 Mast, Guyed 15 m with Erection Kit Five section 15 m mast. Guyed tubular aluminium mast with ground plate, halyard pulley, RF transparent guy kit, full erection kit, mast head gibbet and erection instructions. Designed to withstand wind speeds up to 144 kph (40 m/s) in clear air with head loads up to 12 kg, subject to ground anchoring. NOTE: • Guying details: Five guy sets, each with four guy wires. 7 m guy radius. • Mast suitable for air freight. COMPATIBILITY: • Compatible with Tuned Long Wire (15-00403), Travelling Wave Dipole (78-01248, 78-01249, 78-01250), Full Delta (78-01012 and 78-01246) TFD411 (15-00411-0XX series). Check antenna section for specific details of antennas see page 97. NOTE: Pictures for illustrative purposes only. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 107 Antennas MASTS, GUYED 10 M PRODUCT NGT Antenna Masts PART NO. 15-60013 TRANSCEIVER DESCRIPTION Mast, Guyed 10 m, Lightweight Mast Lightweight guyed aluminium mast, halyard, and all hardware for ground mounting. NOTE: • Guy details: Two guy sets, each with three guy wires and one back stay guy. 5 m guy radius. • Mast suitable for air freight. COMPATIBILITY: • Compatible with Tuned Long Wire (15-00403), TFD411 (15-00411-0XX series). Check antenna section for recommended masts for these antennas. 15-60033 15-60034 Mast, Guyed 10 m, Premium Mast (Raw) Mast, Guyed 10 m, Premium Mast (Black) Lightweight guyed aluminium mast available in raw finish or painted black. This mast features full stainless steel guys with rope tails and turnbuckles for quicker and easier installation. Mast kit includes rope halyard, guy anchors (for ground mount) hammer, spintight for cable clamps, and installation instructions. NOTE: • Guy details: Two guy sets, each with three guy wires and one back stay guy. 5 m guy radius. • Mast suitable for air freight. COMPATIBILITY: • Compatible with Tuned Long Wire (15-00403), TFD411 (15-00411-0XX series). Check antenna section for recommended masts for these antennas. ACCESSORIES: 15-60035 Gibbet, 10 m Mast Gibbet assembly for mounting antennas to the 10 m Premium mast in Inverted V configuration. NOTE: Required when mounting the TFD411 series antenna (1500411-0XX) in inverted V using the 10 m Lightweight (1560013) or 10 m Premium masts (15-60033 or 15-60034) Page 108 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas NGT COAXIAL CABLES TYPE RG58 PRODUCT Coaxial Cable TRANSCEIVER PART NO. DESCRIPTION 08-01503-002 Cable, Coax Assembly, UHF Type Connectors, RG58, 2 m 08-01503-006 Cable, Coax Assembly, UHF Type Connectors, RG58, 6 m 08-01503-008 Cable, Coax Assembly, UHF Type Connectors, RG58, 8 m 08-01503-020 Cable, Coax Assembly, UHF Type Connectors, RG58, 20 m 08-01503-030 Cable, Coax Assembly, UHF Type Connectors, RG58, 30 m 08-05837-002 Cable, Coax Assembly, UHF to N-type Connectors, RG58, 2 m 08-05837-006 Cable, Coax Assembly UHF to N-type Connectors, RG58, 6 m 08-05837-010 Cable, Coax Assembly UHF to N-type Connectors, RG58, 10 m 08-05837-020 Cable, Coax Assembly UHF to N-type Connectors, RG58, 20 m 08-05837-030 Cable, Coax Assembly UHF to N-type Connectors, RG58, 30 m 60-11163-221 Plug, UHF (RG58) W/proof Coaxial Cables Type RG58 NGT COAXIAL CABLES TYPE RG213 PRODUCT TRANSCEIVER PART NO. DESCRIPTION 08-04971-006 Cable, Coax Assembly, UHF Type Connectors, RG213, 6 m 08-04971-010 Cable, Coax Assembly, UHF Type Connectors, RG213, 10 m 08-04971-030 Cable, Coax Assembly, UHF Type Connectors, RG213, 30 m 08-04971-050 Cable, Coax Assembly, UHF Type Connectors, RG213, 50 m 08-04971-100 Cable, Coax Assembly, UHF Type Connectors, RG213, 100 m 08-01233 Strain Relief Reduces strain on connector when supporting RG213 cable assemblies. Coaxial Cables Type RG213 30-38000-002 Shackle Used to attach strain relief to the antenna. 60-11163-204 Plug, UHF (RG213) W/proof Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 109 Antennas NGT LIGHTNING PROTECTION PRODUCT TRANSCEIVER PART NO. 15-00464 Lightning Protection DESCRIPTION Lightning Arrestor Self-resetting spark gap arrestor. Requires a good earth to divert energy from a nearby lightning strike. NOTE: Extra length of coaxial cable or extra UHF plug may need to be ordered to fit lightning arrestor into RF feed system. Page 110 30-37601-002 Copper Earth Strip 50 mm x 0.46 mm (26 gauge) supplied in units of 1 m 15-00163 Earth Stake 1.8 m long x 13 mm with clamp for earth wire/strip. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas This page has been intentionally left blank. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 111 Antennas for Australia 3040 AUTOMATIC TUNING WHIP STANDARD PACKAGE PRODUCT ANT-3040-STD NGT TRANSCEIVER PART NO. 3040 Automatic Tuning Whip Antenna Standard Package for Australia DESCRIPTION 3040 Automatic Tuning Whip Standard Package The 3040 Automatic Whip Antenna is a low profile, rugged, lightweight unit designed for mobile installations. It provides fast automated tuning across the HF band. The 3040 is easy to install and meets MIL-STD-810F for shock, immersion, dust and vibration. NOTE: Supplied with 6 m cables to connect the 3040 Antenna to an NGT™ Transceiver. COMPRISING: 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23085 78-23086 15-60012 • • • • • • • • 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Fibreglass Whip, 1.6 m 3040 Stainless Steel Whip, 1.6 m 3040 Installation Handbook (includes sealing kit) STANDARD FEATURES: • • • • Page 112 2.5 to 30 MHz 125 W PEP voice or data Fast tuning typically < 1sec Tune from memory Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas for Australia 3040 AUTOMATIC TUNING WHIP EXPLORER PACKAGE PRODUCT NGT TRANSCEIVER PART NO. ANT-3040-EXP DESCRIPTION 3040 Automatic Tuning Whip Explorer Package The 3040 Automatic Whip Antenna is a low profile, rugged, lightweight unit designed for mobile installations. It provides fast automated tuning across the HF band. The 3040 is easy to install and meets MIL-STD-810F for shock, immersion, dust and vibration. NOTE: Supplied with 6 m cables to connect the 3040 Antenna to an NGT™ Transceiver. COMPRISING: 08-07007-001 08-05627-006 08-01503-006 08-07148-001 78-18058 78-23086 15-60012 • • • • • • • 3040 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 3040 Spring Riser, Fibreglass 3040 Stainless Steel Whip, 1.6 m 3040 Installation Handbook (includes sealing kit) STANDARD FEATURES: • • • • Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2.5 to 30 MHz 125 W PEP voice or data Fast tuning typically < 1sec Tune from memory Page 113 Antennas for Australia 9350 AUTOMATIC TUNING WHIP STANDARD PACKAGE PRODUCT ANT-9350-STD NGT TRANSCEIVER PART NO. 9350 Automatic Tuning Whip Standard Package for Australia DESCRIPTION 9350 Automatic Tuning Whip Standard Package A robust antenna designed for mobile installations requiring flexible, high performance HF communications. It provides fast automated tuning over the HF range. The 9350 is easy to install, and meets MIL-STD-810F for shock and vibration. NOTE: Supplied with 6 m cables to connect the 9350 Antenna to an NGT™ Transceiver. COMPRISING: 08-05063-001 08-05627-006 08-01503-006 08-05140-001 78-23007-003 78-23025 15-04142-EN • • • • • • • 9350 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 9350 Spring 9350 Fibreglass Whip, 1.6 m 9350 Tapered Stainless Steel Whip, 1.2 m Automatic Tuning Whip Antenna 9350 Installation Handbook STANDARD FEATURES: • 125 W PEP voice or data • Tuning typically 2 seconds • Transmit frequency range 2 to 30 MHz depending on antenna • Receive frequency range 250 kHz to 30 MHz Page 114 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antennas for Australia 9350 AUTOMATIC TUNING WHIP VENTURER PACKAGE PRODUCT ANT-9350-VENT NGT TRANSCEIVER PART NO. 9350 Automatic Tuning Whip Venturer Package for Australia DESCRIPTION 9350 Automatic Tuning Whip Venturer Package A robust antenna designed for mobile installations requiring flexible, high performance HF communications. It provides fast automated tuning over the HF range. The 9350 is easy to install, and meets MIL-STD-810F for shock and vibration. NOTE: Supplied with 6 m cables to connect the 9350 Antenna to an NGT™ Transceiver. COMPRISING: 08-05063-001 08-05627-006 08-01503-006 78-23056 15-04142-EN • • • • • 9350 Main Assembly Control NGTTM /EnvoyTM to 9350/304X Cable, 6 m Coax Assembly Cable, UHF Type Connectors, RG58, 6 m 9350 Tapered Stainless Steel Whip, 1.6 m Automatic Tuning Whip Antenna 9350 Installation Handbook STANDARD FEATURES: • 125 W PEP voice or data • Tuning typically 2 seconds • Transmit frequency range 2 to 30 MHz depending on antenna • Receive frequency range 250 kHz to 30 MHz Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 115 Antennas for Australia fThis page has been intentionally left blank. Page 116 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Remote Control ENVOY™ REMOTE CONTROL ACCESSORIES— ETHERNET PRODUCT REMOTE-ENVOY-ETH PART NO. Ethernet Remote Control Accessories — Ethernet Envoy Remote Control Accessories — Ethernet DESCRIPTION Envoy Remote Control Accessories — Ethernet These parts are required to facilitate connection of a 2230 Desktop Console to an X1 or X2 RF Unit via Ethernet cable. The transceiver to Ethernet adaptor is used to convert the 10-pin RF Unit control connector to RJ45 Ethernet socket. The power supply is required to provide power to the 2230 Desktop Console as the Ethernet cable does not provide power from the RF Unit. COMPRISING: 08-07215-001 78-16019 67-9020# Cable, Tcvr to Ethernet Adaptor Desk Console AC Mains Power Supply 2C IEC C7 Cable, 2 m (for cable options, see page 119, NGT™ Remote Control Accessories) 67-90802 Cable, Ethernet Straight CAT-5E, 2 m Blue 67-90803 Cable, Ethernet Straight CAT-5E, 10 m Blue 67-90805 Cable, Ethernet Straight CAT-5E, 100 m Blue # denotes the cable variant depending upon country of use Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 117 Remote Control NGT NGT™ REMOTE CONTROL EQUIPMENT—2-WIRE PRODUCT PART NO. NGT™ Remote Control Equipment — 2-wire Interface TRANSCEIVER DESCRIPTION NGT™ Remote 2-wire Interface An NGT™ Remote Control System is the smart and easy way to achieve clear and reliable communications when your transceiver site is located in an area affected by electrical interference. The NGT™ HF transceiver is relocated to a ‘quiet’ area, while the transceiver is fully operated from a convenient location, such as an office or communication centre. To create a remote control system, an NGT™ Base Station configuration is extended with a 3030 NGT™ Remote Interface (NRI), which converts both audio and control into RS232 signals. A line modem is required for 2-wire leased line operation. NOTE: • Remote control configurations can only be used with NGTTM SR and ASR Transceivers. • Only used with the 3012 HF Data Modem. • Two NRIs are required for a complete remote control system. • Specify the mains connector type (AU, EU, UK or US), see page 119, NGT™ Remote Control Accessories. COMPRISING: REMOTE-NRI-CTRL-2W 08-05864-001 15-00135 78-13016 78-16019 60-00063-501 08-04146-001 08-05858-001 08-05859-001 67-90203 30-11208-000 15-04102-EN REMOTE-NRI-TCVR-2W 08-05864-001 15-00134 78-13016 60-00063-501 08-05610-001 08-04146-001 08-05858-001 08-05868-001 08-05859-001 30-11208-000 Page 118 Control Site • 3030 NGTTM Remote Interface • NGTTM Remote Control Earth Kit for the Control Site • Leased Line Modem • Power Supply Unit, 90 to 264 V AC • 6-way Modular Wall Mounting Socket • 6-way Phone Cable • NRI to Line Modem Cable • NRI to Line Modem Power Cable • 2C IEC C7 Cable, 2 m (for cable options, see page 119, NGT™ Remote Control Accessories) • Self Adhesive Rubber Feet (x4) • Remote Control NGTTM Systems Reference Manual (see page 165, Language Support for translations of this manual) Transceiver Site • 3030 NGTTM Remote Interface • NGTTM Remote Control Earth Kit for the Remote Site • Leased Line Modem • 6-way Modular Wall Mounting Socket • CIB Interface Cable, 0.5 m • 6-way Phone Cable • NRI to Line Modem Cable • Power Cable to RF Unit and NRI • NRI to Line Modem Power Cable • Self Adhesive Rubber Feet (x4) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Remote Control NGT NGT™ REMOTE CONTROL ACCESSORIES PRODUCT PART NO. 08-05920-001 NGT™ Remote Control Accessories TRANSCEIVER DESCRIPTION Cable, DC Extension, 1 m The extra length this cable provides may be needed to connect the power supply to the RF Unit in rack configurations. NGT™ Remote Control Accessories 08-05610-001 08-05610-002 08-05610-006 08-05610-030 Cable, CIB Interface, 0.5 m Cable, CIB Interface, 2 m Cable, CIB Interface, 6 m Cable, CIB Interface, 30 m 08-05086-001 08-05086-006 Cable, Data Interface, 2 m Cable, Data Interface, 6 m 67-90200 Cable, 2C IEC C7 AUS, 2 m 67-90201 Cable, 2C IEC C7 UK, 2 m 67-90202 Cable, 2C IEC C7 US, 2 m 67-90203 Cable, 2C IEC C7 EU, 2 m 15-00172-001 NGT™ Universal 19" Rack-mounting Tray 3RU with Blank Front Panel Suitable for a 3030 NRI. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 119 Remote Control NGT NGT™ SPLIT-SITE EQUIPMENT — 2-WIRE PRODUCT TRANSCEIVER PART NO. DESCRIPTION NGT™ Split-site System — 2-wire Interface NGT™ Split-site Equipment — 2-wire Interface An NGT™ Split-site Remote System consists of two or three sites. Each site consists of the split-site equipment listed below, in addition to the transceiver equipment. An NGT™ Split-site Remote System can be used to split control, transmit and receive functions of an NGT™ SR or ASR Transceiver system into one of the following basic configurations: • NGT™ remote transmitter and remote receiver system (3 sites) • NGT™ remote transceiver system (2 sites) • NGT™ local transmitter, remote receiver system (2 sites) The system operates with a standard 2-wire interface. Contact Codan for detailed system configurations. NOTE: • Split-site configurations can only be used with NGTTM SR and ASR Transceivers, and requires one transceiver at each site. • All NGTTM SR and ASR Transceiver functions available. • Existing transceivers may require modifications for use in split-site configurations. Contact Codan for details. • Suitable for use with the 3012 HF Data Modem. COMPRISING: REMOTE-SPLIT-CTRL-8571-2W Control Site 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10509-000 15-30067 15-04125-EN • • • • • • • • • Split-site Interface Control Junction Box 8571 NGTTM Remote Control Interface Earth Wire, 0.5 m (x5) CIB Interface Cable, 0.5 m Split-site Power Adaptor Cable 8571 NGTTM Interface Controller Cable Opt 2 W, 2-wire (Factory Fit) (x2) NGTTM Audio Mute Modification Split-site Remote Control NGTTM Systems Reference Manual (English) NOTE: Control Site can only used for transmitting. Continued on the next page Page 120 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Remote Control NGT NGT™ SPLIT-SITE EQUIPMENT—2-WIRE cont. PRODUCT PART NO. TRANSCEIVER DESCRIPTION Receive Site REMOTE-SPLIT-RX-8571-2W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10509-000 15-30068 COMPRISING • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 2 W, 2-wire (Factory Fit) • NGTTM Disable PA Modification NOTE: Receive Site can only be used for receiving, transmitter is disabled. Transmit Site REMOTE-SPLIT-TX-8571-2W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10509-000 COMPRISING • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 2 W, 2-wire (Factory Fit) NOTE: Transmit Site is configured for transmitting only but can be switched to either receive, or transmit and receive. Transmit & Receive Site REMOTE-SPLIT-TXRX-8571-2W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10509-000 COMPRISING • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 2 W, 2-wire (Factory Fit) NOTE: Transmit and Receive Site is configured for transmitting and receiving but can be switched to either receive or transmit only. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 121 Remote Control NGT NGT™ SPLIT-SITE EQUIPMENT—4-WIRE PRODUCT PART NO. NGT™ Split-site Equipment — 4-wire Interface TRANSCEIVER DESCRIPTION NGT™ Split-site System — 4-wire Interface An NGT™ Split-site Remote System consists of two or three sites. Each site consists of the split-site equipment listed below, in addition to the transceiver equipment. An NGT™ Split-site Remote System can be used to split control, transmit and receive functions of an NGT™ SR or ASR Transceiver system into one of the following basic configurations: • NGT™ remote transmitter and remote receiver system (3 sites) • NGT™ remote transceiver system (2 sites) • NGT™ local transmitter, remote receiver system (2 sites) The system operates with a standard 4-wire interface. Contact Codan for detailed system configurations. NOTE: • Split-site configurations can only be used with NGTTM SR and ASR Transceivers, and requires one transceiver at each site. • All NGTTM SR and ASR Transceiver functions available. • Existing transceivers may require modifications for use in split-site configurations. Contact Codan for details. • Suitable for use with the 3012 HF Data Modem. Control Site REMOTE-SPLIT-CTRL-8571-4W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10510-002 15-30067 15-04125-EN COMPRISING: • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 4 W, 4-wire Interface Master Site (x2) • NGTTM Audio Mute Modification • Split-site Remote Control NGTTM Systems Reference Manual (English) Continued on the next page Page 122 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Remote Control NGT NGT™ SPLIT-SITE EQUIPMENT—4-WIRE cont. PRODUCT PART NO. TRANSCEIVER DESCRIPTION Receive Site REMOTE-SPLIT-RX-8571-4W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10510-004 15-30068 COMPRISING: • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 4 W, 4-wire Interface Slave Receive Site • NGTTM Disable PA Modification NOTE: Receive Site is only used for receiving, transmitter is disabled. Transmit Site REMOTE-SPLIT-TX-8571-4W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10510-003 COMPRISING: • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 4 W, 4-wire Interface Slave Transmit Site NOTE: Transmit Site is configured for transmitting only but can be switched to either receive, or transmit and receive. Transmit & Receive Site REMOTE-SPLIT-TXRX-8571-4W 08-05630-005 08-05994-001 08-04515-001 08-05610-001 08-05989-001 08-05990-001 15-10510-003 COMPRISING • Split-site Interface Control Junction Box • 8571 NGTTM Remote Control Interface • Earth Wire, 0.5 m (x5) • CIB Interface Cable, 0.5 m • Split-site Power Adaptor Cable • 8571 NGTTM Interface Controller Cable • Opt 4 W, 4-wire Interface Slave Transmit Site NOTE: Transmit and Receive Site is configured for transmitting and receiving but can be switched to either receive or transmit only. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 123 Remote Control NGT SPLIT-SITE ACCESSORIES PRODUCT TRANSCEIVER PART NO. 15-00164-010 Split-site Accessories Page 124 DESCRIPTION 19" Rack-mounting Frame for 8571 Split-site Remote Interface 08-04146-001 Cable, 6-way Phone 08-04284 Cable, Phone Plug Adaptor Modular to 604 Plug 08-05610-001 08-05610-002 08-05610-006 08-05610-030 Cable, CIB Interface, 0.5 m Cable, CIB Interface, 2 m Cable, CIB Interface, 6 m Cable, CIB Interface, 30 m 08-05086-001 08-05086-006 Cable, Data Interface, 2 m Cable, Data Interface, 6 m 15-10509 Opt 2 W, 2-wire (Retro Fit) 15-10510 Opt 4 W, 4-wire (Retro Fit) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 19" Racks & Accessories STANDARD RACK CONFIGURATIONS Standard Rack Configurations PRODUCT DESCRIPTION PART NO. 08-06130-001 Basic High Power Rack Configuration NGT Designed to rack mount a basic NGT™/Envoy™ High Power 500 W/1000 W system. TRANSCEIVER COMPRISING: Standard Rack Configurations • 19" 27RU rack complete with rear door, vented top and side panels • NGT™/Envoy™ universal rack mount tray for an NGT™/ Envoy™ Transceiver • NGT™/Envoy™ rack mount tray for 3020 Transceiver Supply • Rack mount blanking panels 1RU, 2RU and 3RU supplied • Rack mount vent panels 1RU and 4RU supplied • Pre-fitted equipment rails • Assorted cable ties, screws, washers and cage nuts NOTE: • Rack comes pre-assembled ready for a NGT™/Envoy™ Transceiver and high power amplifier to be mounted. • 6RU of space available for additional equipment. • NGT™/Envoy™ Transceiver, power amplifier and power supply units are ordered separately. • Does not include a 1 m DC Extension Cable for the NGT™/Envoy™ Transceiver. 08-06130-002 Remote Control, High Power Rack Configuration NGT Designed to rack mount a NGT™ High Power Remote Control system. TRANSCEIVER COMPRISING: • 19" 27RU rack complete with rear door, vented top and side panels • NGT™ universal rack mount tray for a NGT™ Transceiver • NGT™ universal rack mount tray for NGT™ Remote Interface (NRI) remote control • NGT™ rack mount tray for a 3020 Heavy Duty Transceiver Supply • Rack mount blanking panels 1RU and 2RU supplied • Rack mount vent panels 1RU and 4RU supplied • Pre-fitted equipment rails • Assorted cable ties, screws, washers and cage nuts 19" Racks & Accessories Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 NOTE: • Rack comes pre-assembled ready for a NGT™ Transceiver and high power amplifier to be mounted. • 3RU of space available for additional equipment. • NGT™ Transceiver, NRI remote control, high power amplifier and power supply units are ordered separately. • Does not include a 1 m DC Extension Cable for the NGT™ Transceiver. Page 125 19" Racks & Accessories NGT STANDARD RACK CONFIGURATIONS PRODUCT PART NO. 08-06130-003 Standard Rack Configurations2 TRANSCEIVER DESCRIPTION Remote Control and Data Modem High Power Rack Configuration Designed to rack mount a NGT™ High Power Remote Control Data system. COMPRISING: • 19" 27RU rack complete with rear door, vented top and side panels • NGT™ universal rack mount tray for a NGT™ Transceiver • NGT™ universal rack mount system tray for NRI remote control • NGT™ universal rack mount system tray for a HF data modem • NGT™ rack mount tray for a 3020 Heavy Duty Transceiver Supply • Rack mount vent panels 1RU and 4RU supplied • Pre-fitted equipment rails • Assorted cable ties, screws, washers and cage nuts NOTE: • Rack comes pre-assembled ready for a NGT™ Transceiver and high power amplifier to be mounted. • No space available for additional equipment. • NGT™ Transceiver, NRI remote control, high power amplifier and power supply units are ordered separately. • Does not include a 1 m DC Extension Cable for the NGT™ Transceiver. 08-06130-004 Split-site Remote Control High Power Rack Configuration Designed to rack mount a NGT™ High Power Split-Site Remote Control system. COMPRISING: • 19" 27RU rack complete with rear door, vented top and side panels • NGT™ universal rack mount tray for a NGT™ Transceiver • NGT™ rack mount tray for a 3020 Power supply • Rack mount blanking panels 1RU and 2RU supplied • Rack mount vent panels 1RU and 4RU supplied • Pre-fitted equipment rails • Assorted cable ties, screws, washers and cage nuts NOTE: • Rack comes pre-assembled ready for a NGT™ Transceiver and high power amplifier to be mounted. • 3RU space available for additional equipment. • NGT™ Transceiver, NRI remote control, high power amplifier and power supply units are ordered separately. • Does not include a 1 m DC Extension Cable for the NGT™ Transceiver. Page 126 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 19" Racks & Accessories NGT 19" RACK CABINETS PRODUCT TRANSCEIVER PART NO. DESCRIPTION 08-05288-008 Rack Cabinet, 8RU High, 19" Format, 500 mm Deep 08-05288-012 Rack Cabinet, 12RU High, 19" Format, 500 mm Deep 08-05288-018 Rack Cabinet, 18RU High, 19" Format, 500 mm Deep 19" Rack Cabinets 19" Rack Mount System Trays 19" RACK MOUNT SYSTEM TRAYS Rack Mounts PRODUCT DESCRIPTION PART NO. 15-00172-001 NGT TRANSCEIVER 15-00172-002 NGT TRANSCEIVER NGT™ Universal 19" Rack-mounting Tray 3RU with Blank Front Panel Suitable for NGT™ RF units, 3030 NGT™ Remote Interface. NGT™/Envoy™ Universal 19" Rack-mounting Tray 3RU, Front Panel with Speaker Grill and Mounting Holes Suitable for NGT™/Envoy™ RF unit. Speaker can be mounted behind grill and handset can be mounted on front panel using cradle. NOTE: Speaker and handset cradle not included. 15-00176 NGT 19" Rack-mounting Frame suitable for 3020 Transceiver Supply, and 3012 or 3212 HF Data Modems TRANSCEIVER 15-00164-010 NGT 19" Rack-mounting Frame for 8571 Split-site Remote Interface TRANSCEIVER Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 127 19" Racks & Accessories NGT 19" RACK MOUNT BLANKING PANELS PRODUCT PART NO. 15-00173 TRANSCEIVER DESCRIPTION Set of 1RU + 2RU Blank Front Panels Suitable for covering gaps or holes in rack facia. 19" Rack Mount Blanking Panels 30-35002-019 19" 4RU Vent Panel 30-35002-006 19" 1RU Vent Panel 19" Rack Mount Accessories NGT 19" RACK MOUNT ACCESSORIES PRODUCT PART NO. 30-35002-020 TRANSCEIVER DESCRIPTION Fixed Equipment Rail, 457 mm Long NOTE: Suitable for 27RU rack cabinet only. 08-05920-001 Cable, DC Extension, 1 m NOTE: Required for the transceiver when it is rack mounted. 05-06374 Page 128 Earth Braid, 1.5 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver Configurations 2110 SERIES TRANSCEIVER KIT PRODUCT 2110 Series Transceiver Kit PART NO. 2110-TCVR DESCRIPTION 2110 series Transceiver Kit The 2110 series Transceivers are ideal for your long distance portable communications. They are designed to meet the most demanding mission and user requirements. Available in two versions, the 2110v is for basic voice only operations and the 2110 has additional interface and interoperability capabilities. The 2110 Transceiver is now available with a front panel mounted socket for connection of an external GPS antenna, e.g. for mobile or indoor applications where GPS signal reception is required. NET WEIGHT: 3.28 kg (7.23 lbs) 2110v & 2110 Transceiver Kits A 2110 series Transceiver Kit consists of a transceiver unit and standard accessories listed below. The following pages detail the parts required for a fully operational manpack system. 08-06155-001 08-06155-008 08-06155-002 08-06155-009 08-06155-003 78-08000 08-06259-001 15-00446 15-04136-## TRANSCEIVER UNITS: • 2110 SSB Transceiver Unit (1.5 ppm) — std frequency stability • 2110 SSB Transceiver (1.5 ppm) — std frequency stability, with front panel GPS connector • 2110 SSB Transceiver Unit (0.5 ppm) — high frequency stability • 2110 SSB Transceiver (0.5 ppm) — high frequency stability, with front panel GPS connector • 2110v SSB Transceiver Unit (1.5 ppm) — std frequency stability STANDARD ACCESSORIES: • H-250/U Telephone Handset • Earth wire with clip • Counterpoise 4-wire kit • 2110 series Manpack Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) STANDARD FEATURES: • 1.6–30 MHz, 400 channels, 10 networks • 25 W/5 W (PEP) selectable output power • 12 V DC, USB/LSB/AM • Internal automatic antenna tuner • Multi-net scanning • In-built Easitalk™ speech noise reduction • Comprehensive calling capabilities, including emergency call, phone call, selective call, message call, remote diagnostics • Call logging • Up to 65 hours use on a single charge (17Ah battery) • Selectable output power • Computer interface (RS232) for PC control • Front panel programming (where permitted) • Extensive Built-In-Test functions • Meets MIL-STD-810F for shock, vibration, immersion and dust AVAILABLE OPTIONS & ACCESSORIES: ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 • See pages 136 and 139 for 2110 Options and Accessories. Page 129 2110 Transceiver Configurations PATROL CONFIGURATION Patrol Configuration PRODUCT PART NO. 2110-TCVR-PATROL DESCRIPTION The Patrol Configuration provides the bare essentials for basic manpack operation. NOTE: An appropriate battery charger needs to be ordered separately. COMPRISING: 08-06155-### NET WEIGHT: 3.72 kg (8.2 lbs) 78-08000 08-06259-001 15-00446 15-04136-## 2110 series Transceiver Kit • Transceiver Unit (see page 135, 2110 Transceiver Units for descriptions of the transceiver units) • H-250/U Telephone Handset • Earth wire with clip • Counterpoise 4-wire kit • 2110 series Manpack Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) 15-00452 Collapsible Whip Antenna 3 m (10') Extremely quick-to-erect whip antenna for use while stationary. Comes with a goose neck base to adjust the antenna angle. 15-00454 Long Wire Antenna and Adaptor (1.6–30 MHz) Kevlar reinforced tactical wire antenna with throw rope and accessories. 08-06185-001 Battery Pack 12 V 8Ah NiMH Lightweight, robust and waterproof battery pack. Provides for up to 30 hours of continuous operation (Rx/Tx 9:1). 15-00218 Softpack Backpack Ultra-lightweight economy backpack with extra pockets for transceiver accessories. NET WEIGHT: 0.4 kg (0.88 lbs) NET WEIGHT: 0.44 kg (0.97 lbs) NET WEIGHT: 2.1 kg (4.63 lbs) NET WEIGHT: 1.23 kg (2.71 lbs) AVAILABLE OPTIONS & ACCESSORIES: See pages 136 and 139 for 2110 Options and Accessories. ## denotes language version ### denotes the type of transceiver unit Page 130 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver Configurations EXPLORER CONFIGURATION PRODUCT Explorer Configuration PART NO. 2110-TCVR-EXP DESCRIPTION The Explorer Configuration provides all the requirements for a complete stand-alone HF communications system suitable for a range of uses. COMPRISING: 08-06155-### NET WEIGHT: 3.72 kg (8.2 lbs) 78-08000 08-06259-001 15-00446 15-04136-## 2110 series Transceiver Kit • Transceiver Unit (see page 135, 2110 Transceiver Units for descriptions of the transceiver units) • H-250/U Telephone Handset • Earth wire with clip • Counterpoise 4-wire kit • 2110 series Manpack Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) 15-10525-000 Opt GPS Receiver (Factory Fit) Enables GPS location and tracking capabilities in the 2110 series Transceivers. 15-00459 Knock Over Whip Antenna 1.5 m (5') Robust short whip antenna suitable for communications while on foot. 15-00452 Collapsible Whip Antenna 3 m (10') Extremely quick-to-erect whip antenna for use while stationary. Comes with a goose neck base to adjust the antenna angle. 15-00454 Long Wire Antenna and Adaptor Kevlar reinforced tactical wire antenna with throw rope and accessories. 08-06185-001 Battery Pack 12 V 8Ah NiMH Lightweight, robust and waterproof battery pack. Provides for up to 30 hours of continuous operation (Rx/Tx 9:1). NET WEIGHT: 0.02 kg (0.04 lbs) NET WEIGHT: 0.28 kg (0.62 lbs) NET WEIGHT: 0.4 kg (0.88 lbs) NET WEIGHT: 0.44 kg (0.97 lbs) NET WEIGHT: 2.1 kg (4.63 lbs) Continued on the next page ## denotes language version ### denotes the type of transceiver unit Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 131 2110 Transceiver Configurations EXPLORER CONFIGURATION CONT. PRODUCT PART NO. 78-02007 DESCRIPTION 2110 Battery Charger AC 1 A Used to charge the 2110 battery via the front panel or directly. Supplied with one AC mains cable. NOTE: When ordering, please specify the required AC input cable (AUS, UK, USA or EU), see page 162, Charger Input Cables AC. NET WEIGHT: 0.37 kg (0.82 lbs) 08-06215-001 19-way battery charger output cable for 2110 Used to charge the 2110 series Transceivers via the front panel. 08-06214-001 6-way battery charger output cable Used to charge the battery directly. 15-00216-001 External Frame Backpack NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 4.3 kg (9.48 lbs) AVAILABLE OPTIONS & ACCESSORIES: See pages 136 and 139 for 2110 Options and Accessories. Page 132 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver Configurations HOMELAND SECURITY CONFIGURATION Homeland Security Configuration PRODUCT DESCRIPTION PART NO. 2110-TCVR-HS The Homeland Security Configuration provides the complete package for a quick deploy communications solution. It features comprehensive interoperability, GPS location and tracking, and extra long battery life. COMPRISING: NET WEIGHT: 3.72 kg (8.2 lbs) 08-06155-002 78-08000 08-06259-001 15-00446 15-04136-## 2110 series Transceiver Kit • Transceiver Unit • H-250/U Telephone Handset • Earth wire with clip • Counterpoise 4-wire kit • 2110 series Manpack Transceiver Getting Started Guide, includes Reference Manual on CDROM (see page 165, Language Support for translations of this guide) 15-10532 Opt MIL-STD-188-141B ALE Comprehensive ALE interoperability, fully compliant with MIL-STD-188-141B ALE and JITC certified. Includes the features of FED-STD-1045 ALE available in option 15-10479. 15-10525-000 Opt GPS Receiver (Factory Fit) Enables GPS location and tracking capabilities in the 2110 series Transceivers. 15-00452 Collapsible Whip Antenna 3 m (10') Extremely quick-to-erect whip antenna for use while stationary. Comes with a goose neck base to adjust the antenna angle. 15-00454 Long Wire Antenna and Adaptor Kevlar reinforced tactical wire antenna with throw rope and accessories. 08-06186-001 Battery Pack 12 V 13Ah NiMH Heavy duty, waterproof battery pack. Provides for up to 50 hours of continuous operation (Rx/Tx 9:1). NET WEIGHT: 0.02 kg (0.04 lbs) NET WEIGHT: 0.4 kg (0.88 lbs) NET WEIGHT: 0.44 kg (0.97 lbs) NET WEIGHT: 2.9 kg (6.39 lbs) Continued on the next page ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 133 2110 Transceiver Configurations HOMELAND SECURITY CONFIGURATION CONT. PRODUCT PART NO. 78-02007 DESCRIPTION 2110 Battery Charger AC 1 A Used to charge the 2110 battery via the front panel or directly. Supplied with one AC mains cable. NOTE: When ordering, please specify the required AC input cable (AUS, UK, USA or EU), see page 162, Charger Input Cables AC. NET WEIGHT: 0.37 kg (0.82 lbs) 08-06215-001 19-way battery charger output cable Used to charge the 2110 series Transceivers via the front panel. 08-06214-001 6-way battery charger output cable Used to charge the battery directly. 15-00216-001 External Frame Backpack NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 4.3 kg (9.48 lbs) AVAILABLE OPTIONS & ACCESSORIES: See pages 136 and 139 for 2110 Options and Accessories. Page 134 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver 2110 TRANSCEIVER UNITS PRODUCT Transceiver Units PART NO. DESCRIPTION 2110 Transceiver Units NOTE: Options and accessories for the manpack transceivers need to be ordered separately. 08-06155-001 08-06155-008 2110 SSB Tcvr Unit (1.5 ppm) 2110 SSB Tcvr Unit (1.5 ppm with front panel GPS connector) The 2110 has additional interface and interoperability capabilities, and is fitted with a 19-way expansion connector for a range of external accessories. It is fully interoperable with Codan’s NGT™/Envoy™ series Transceivers and other commercial and military transceivers. 08-06155-002 08-06155-009 2110 SSB Tcvr Unit (0.5 ppm) 2110 SSB Tcvr Unit (0.5 ppm with front panel GPS connector) This transceiver is similar to 08-06155-001 except it is fitted with a 0.5 ppm high stability reference oscillator. This version of the 2110 Transceiver is required to meet full MIL-STD-188-141B ALE requirements. 08-06155-003 2110v SSB Tcvr Unit (1.5 ppm) This transceiver is similar to 08-06155-001 except it is not fitted with the 19-way external expansion port. The 2110v is a voice-only manpack transceiver. It is fully interoperable with Codan’s NGT™/Envoy™ series Transceivers and other commercial transceivers. NET WEIGHT: 2.5 kg (5.51 lbs) NET WEIGHT: 2.5 kg (5.51 lbs) NET WEIGHT: 2.5 kg (5.51 lbs) STANDARD FEATURES: • 1.6 to 30 MHz, 400 channels, 10 networks • 25 W/5 W (PEP) selectable output power • 12 V DC, USB/LSB/AM • 1.5 ppm (parts per million) standard frequency stability • Internal automatic antenna tuner • Multi-net scanning • In-built Easitalk™ speech noise reduction • Comprehensive calling capabilities, including emergency call, phone call, selective call, message call, remote diagnostics • Call logging • Selectable output power • RS232 interface for PC programming • Front panel programming • Extensive Built-In-Test functions • Meets MIL-STD-810F for shock, vibration, immersion and dust • Front panel GPS connector (with relevant variants of 2110 only) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 135 2110 Transceiver 2110 OPTIONS PRODUCT 2110 Options PART NO. DESCRIPTION 15-10558 Opt, Default Open Selcall 15-10525-000 Opt GPS Receiver (Factory Fit) Internally fitted 16-channel GPS receiver module, which enables use with GPS location tracking systems and shows remote locations with distance and bearing. 15-10530-000 Opt 500 Hz Filter (Factory Fit) (2110 only) 500 Hz narrow IF filter that improves performance with morse (CW) and narrow FSK data modems like Pactor-II. NET WEIGHT: 0.02 kg (0.04 lbs) NET WEIGHT: 0.01 kg (0.02 lbs) NOTE: This filter is fitted in addition to the standard 2 kHz filter. Only one filter in addition to the standard filter is possible. 15-10529-000 NOTE: This filter is fitted in addition to the standard 2 kHz filter. Only one filter in addition to the standard filter is possible. NET WEIGHT: 0.01 kg (0.02 lbs) 15-10584-000 NET WEIGHT: 0.15 kg (0.33 lbs) Opt 2.7 kHz BW Filter (Factory Fit) (2110 only) 2.7 kHz wide band filter. 2G Data Enables integrated data modem capability according to MIL-STD-110-188A/B and STANAG 4539. This provides a range of military spec data waveforms from 75 to 9600 bit/s uncompressed, capabile of operating across varying channel conditions. The modem utilises adaptive equalisation and turbo-decoding for maximum performance. Provides efficient email over HF when used in conjunction with RC50-C email gateway (part number 15-04161-CD), see page 58, “RC50-C HF Email Software”. AES-256 Encryption option (15-10595) can be added. NOTE: • This option is also available as a retro fit kit (part number 15-10584). • The 2.7 kHz BW filter option (15-10529-000) is recommended for optimum data throughput performance. • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Page 136 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver 2110 OPTIONS cont. PRODUCT 2110 Options PART NO. 15-10587-000 DESCRIPTION S4538 3G ALE Enables third-generation (3G) Automatic Link Establishment (ALE) according to STANAG 4538. This provides superior calling performance including faster linking, and the ability to link in extermely poor channel conditions. A variety of call types are supported including voice, message, over-the-air sync and GPS positioning. AES-256 Encryption option (part number 15-10595) can be added. NET WEIGHT: 0.15 kg (0.33 lbs) NOTE: • The 2.7 kHz filter (15-10529-000) is fitted as part of the 3G ALE option. • Only recent build standard 2110 Transceivers can support the S4538 retrofit kit. Consult your Codan representative for further information. • The 3G ALE and 2G data capability cannot be used simultaneously. • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10595 Envoy X1 Options Opt AES-256 Encryption Adds AES-256 Encryption, with support for up to 256 preloaded keys. Suitable for use in conjunction with the MIL-STANAG 2G Data and 3G ALE options (part numbers 15-10584-000 and 15-10587-000). NOTE: • KMS/KFS Key Fill Software recommended (see page 139, Key Management Software). 15-10531-000 NET WEIGHT: 0.04 kg (0.09 lbs) Opt CES-128 Encryptor Module (Factory Fit) High grade Voice Encryptor Module that provides high grade voice security with exceptional recovered audio quality. NOTE: • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 137 2110 Transceiver 2110 OPTIONS cont. PRODUCT 2110 Options PART NO. 15-10553-000 DESCRIPTION Opt AES-256 DV Encryptor Module (Factory Fit) Digital Voice Encryptor module providing excellent digital voice quality and high grade AES-256 bit encryption. Selectable vocoder rates of 1200 and 2400 bit/s are available as standard. NOTE: • This option is also available as a retro fit kit (part number 15-10553). • This option is subject to Australian Government Export Controls. A signed End-User Declaration must be provided for supply of this option. 15-10551 Opt Voice Scrambler (CIVS) Codan Integrated Voice Scrambler used to provide basic level voice security capability. 15-10479 Opt FED-STD-1045 ALE/CALM™ Fully compatible with FED-STD-1045 ALE capabilities and enhanced with Codan Automated Link Management (CALM™). Includes facilities for Selective Calls, All Calls, Phone Calls, Text Messaging and GPS Position Calls. 15-10532 Opt MIL-STD-188-141B ALE Full Only available for the 2110 Transceiver, this option provides full FED-STD-1045 and MIL-STD-188-141B ALE capabilities, including NET call, ALL call, ANY call, Group Call, Wildcard Call, advanced ALE beacon, in-link AMD messaging and a Last Heard station log. With this option the transceiver has 20 networks and 600 available channels. 15-10544 Opt MIL-STD-188-141B Upgrade Used to upgrade a 2110 Transceiver that already has FED-STD-1045 ALE/CALM™ enabled to full MIL-STD-188-141B capability. NOTE: This part should only be used for ordering field upgrade passwords. Page 138 15-10518 Opt Amateur Mode Enables transmit capability with free dial frequencies within Amateur frequency bands. For use by licensed operators only. 15-10481 Opt TxD, Tx Program Disable Disables front panel programming of new transmit frequencies. For use in countries where front panel programming is prohibited by regulatory authorities, e.g. USA and Australia. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver 2110 ACCESSORIES PRODUCT 2110 Accessories PART NO. DESCRIPTION 78-08000 2110 Accessories Handset H-250/U Lightweight military handset with noise cancelling microphone and push-to-talk switch. Includes a coiled cord with a standard H-229 military audio connector. 15-04168-EN Key Management Software (KMS) Key Management Software (KMS) enables you to manage and program encryption keys for Codan’s NGT™/2110/ Envoy™ series Transceivers and stand-alone encrypted devices, e.g. RM50e HF Data Modem. NET WEIGHT: 0.35 kg (0.77 lbs) NOTE: • This product is subject to Australian Government Export Controls. • A signed End-User Declaration must be provided for supply of this option. 15-04171-EN Key Fill Software (KFS) Key Fill Software (KFS) enables you to program encryption keys into Codan’s NGT™/2110/Envoy™ series Transceivers and stand-alone encryption devices, e.g. RM50e HF Data Modem. NOTE: • This product is subject to Australian Government Export Controls. • A signed End-User Declaration must be provided for supply of this option. 08-06901-001 Cable, Data Interface 19way MIL to USB A USB to 19-way MIL Interface Cable for PC control (using RC50-C) and security key programming (KMS/KFS) of the RM50e HF Data Modem and embedded 2G Data Modem (2110 only). Also used for programming of the 2110 Transceiver using NSP. 08-06237-001 Cable, Data Interface 19way MIL to D9F 9-way D to 19-way MIL Interface Cable for PC control (using RC50-C) and security key programming (KMS/KFS) of the RM50e HF Data Modem and embedded RM50 Modem (2110 only). Also used for programming the 2110 Transceiver using NSP. 08-06737-001 Cable, Data Interface 5way MIL to D9F 9-way D to 5-way MIL Interface Cable for security key programming (KMS/KFS) and programming of the 2110v Transceiver using NSP. NET WEIGHT: 0.12 kg (0.26 lbs) NET WEIGHT: 0.13 kg (0.29 lbs) ## denotes language version Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Continued on the next page Page 139 2110 Transceiver 2110 ACCESSORIES cont. PRODUCT 2110 Accessories PART NO. DESCRIPTION 15-04164-EN System Programmer CD Programming software to program 2110 and NGT™ series Transceivers. Programmer interface cable (part number 08-06237-001 or 08-06737-001) needs to be ordered separately. 78-01031 Adaptor, USB to DB-9, Serial Port USB V1.1 compliant and supports Microsoft WindowsTM 2000/XP/Vista/WIN7. 15-00665 Morse Key, Desktop Morse key for desktop use with the 2110 transceiver. Connects to the 19 pin front panel connector. 78-13039 Morse Key, Leg Moun Leg mounted Morse key suitable for man portable use with the 2110 transceiver. Connects to the 19 pin front panel connector. 08-06213-001 Cable, VP-116 Interface Interface cable connecting the VP-116 Voice Privacy Unit to the 2110 Transceiver. 78-01253 Antenna, Active GPS, SMB, 5 m External GPS antenna for use with 2110 series Manpack variants fitted with front panel GPS connector. NET WEIGHT: 0.09 kg (0.2 lbs) NET WEIGHT: 0.2 kg (0.44 lbs) NET WEIGHT: 0.2 kg (0.44 lbs) NET WEIGHT: 0.2 kg (0.44 lbs) NET WEIGHT: 0.26 kg (0.57 lbs) Continued on the next page Page 140 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2110 Transceiver 2110 ACCESSORIES cont. PRODUCT 2110 Accessories PART NO. 15-04136-## DESCRIPTION Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM Printed Getting Started Guide for the 2110 Transceiver. See page 165, Language Support for translations of this guide. NET WEIGHT: 0.22 kg (0.49 lbs) 15-04139-EN Repair Guide, Manpack Transceiver 2110 series Printed Repair Guide for the 2110 series. 15-04139-CD Repair Guide, Manpack Transceiver 2110 series, on CDROM NET WEIGHT: 2.4 kg (5.29 lbs) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 141 2110 Transceiver fThis page has been intentionally left blank. Page 142 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email for 2110 NGT RC50-C HF EMAIL SOFTWARE PRODUCT TRANSCEIVER PART NO. DESCRIPTION 15-04161-CD RC50-C HF Email Software RC50-C HF Email Software Codan’s RC50-C HF Email software provides fast, efficient, error free email capability over HF radio. Operating in conjunction with Codan’s HF Transceivers and 2G Embedded Data and External RM50e Modem, the software operates on a standard Windows™ PC using a single USB port with no specialised PC hardware requirements. When installed, the software runs in the background requiring no user interaction. COMPATIBILITY: • For use with external RM50e HF Data Modem (NGT™ SRx, SR, ASR, Envoy™ X2 Transceivers) and 2G Embedded Data Modem (Envoy X2 and 2110 Manpack transceiver) COMPRISING: • CD-ROM with RC50-C software and documentation STANDARD FEATURES: • • • • • Adaptive rates up to 9600 bit/s Compatible with ALE/CALM™ Intranet/Internet gateway NATO interoperable ISB capable SYSTEM REQUIREMENTS: • • • • • • • Windows™ XP Professional SP2 or Windows™ 7 Intel Pentium IV 800 MHz or better 6 GB or more of free space for email storage 512 MB or more of RAM CD-ROM drive POP3 / SMTP compliant email client Access to any commercial POP3 / SMTP compliant email server for internet connectivity • Serial/USB port for connecting the HF modem to the PC NOTE: • Requires Data Interface Cable (part number 08-06901-001) for connecting the PC to a 2110 series Manpack Transceiver or RM50e HF Data Modem. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 143 Data & Email for 2110 UUPLUS™ SOFTWARE PRODUCT UUPlus™ Email for HF Server Software PART NO. 08-05981-001 DESCRIPTION UUPlus™ Email for HF Server Software Provides HF and Internet email access for up to 25 users. It works in conjunction with UUPlusTM Email for HF Codan Client software, used by each remote station. It has been specifically designed for use with Codan’s HF equipment. UUPlus Software NOTE: • One copy of UUPlusTM Codan Client is required for each user that is to connect to UUPlusTM Codan Server. • A UUPlusTM Codan Server cannot communicate directly to other UUPlusTM Codan Server stations. COMPATIBILITY: • For use with 3012 and 3212 HF Data Modems COMPRISING: • CD-ROM with UUPlusTM Codan Server software and documentation • Single user licence for installation on one machine STANDARD FEATURES: • Works with POP3/SMTP PC email clients such as Outlook Express™. • Capable of interfacing with an Internet Service Provider or Mail Server • Reduces connection time by compressing and combining messages • Automatically resumes interrupted file transfers • Capable of automatically calling the remote user at preset times to deliver mail and collect outgoing mail, or enables the user to check mail manually SYSTEM REQUIREMENTS: • • • • Codan HF SSB Transceiver Codan 3012 or 3212 HF Data Modems Microsoft WindowsTM XP/WIN7 Internet email client with support of POP3 and SMTP protocols • Serial/USB port for connecting the HF modem to the PC • Optional LAN, dialup networking card or line modem for connecting local email clients and server to the internet Continued on the next page Page 144 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email for 2110 UUPLUS™ SOFTWARE CONT. PRODUCT UUPlus™ Email for HF Client Software PART NO. 08-05980-001 DESCRIPTION UUPlus™ Email for HF Client Software Simple and reliable solution for sending email over HF from remote areas. It works in conjunction with UUPlusTM Codan Server software and has been specifically designed for use with Codan’s HF equipment. COMPATIBILITY: • For use with 3012 and 3212 HF Data Modems COMPRISING: • CD-ROM with UUPlusTM Codan Client software and documentation • Single user licence for installation on one machine STANDARD FEATURES: • Works with POP3/SMTP PC email clients such as Outlook Express™. • Reduces connection time by compressing and combining messages • Automatically resumes interrupted file transfers • Capable of automatically answering calls from the server to exchange mail at preset times, or enables the user to check for mail manually • Able to send files directly to other stations SYSTEM REQUIREMENTS: • • • • Codan HF SSB Transceiver Codan 3012 or 3212 HF Data Modems Microsoft WindowsTM XP/WIN7 Internet email client with support of POP3 and SMTP protocols • Serial/USB port for connecting the HF modem to the PC Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 145 Data & Email for 2110 3012 HF DATA MODEM (NO CABLES) PRODUCT 3012 HF Data Modem (No Cables) PART NO. MODEM-3012-NC DESCRIPTION 3012 HF Data Modem (No Cables) 3012 HF Data Modem (No Cables) The 3012 HF Data Modem provides reliable and cost-effective computer text and data communication capabilities for organisations operating in remote areas with little or no telecommunications infrastructure. COMPRISING: 08-05877-004 08-04515-001 30-11208-000 15-04104-CD • • • • 3012 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3012 HF Data Modem User Guide on CDROM (English) STANDARD FEATURES: • Up to 6000 bit/s, error-free data transmission with compression • In-built data compression • Backwards compatible with the Codan 9001/9002 HF Data Modems • Data scrambled for security • In-built serial port optical isolator • Easy to use AT command interface AVAILABLE OPTIONS: • Support for UUPlusTM Email for HF Client or Server software, see page 144, UUPlus™ Software. Page 146 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email for 2110 3012 HF DATA MODEM FOR 2110 WITH 6 M RS232 CABLE 3012 HF Data Modem for 2110 with 6 m RS232 Cable PRODUCT DESCRIPTION PART NO. MODEM-3012-2110-6M 3012 HF Data Modem for 2110 with 6 m RS232 Cable This configuration consists of a 3012 HF Data Modem, 6 m Data Interface Cable, and 1 m 2110 Manpack to 3012 Modem Cable. COMPRISING: 08-05877-004 08-04515-001 30-11208-000 15-04104-CD 3012 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet(x4) 3012 HF Data Modem User Guide on CDROM (English) 08-05086-006 Data Interface Cable, 6 m 08-06422-001 2110 Manpack to 3012 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 147 Data & Email for 2110 3012 ACCESSORIES PRODUCT 3012 Accessories PART NO. 15-00136 DESCRIPTION Cradle, HF Data Modem Vehicle Mounting 3012 Accessories 78-01031 Adaptor, USB to DB-9, Serial USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. 60-00098-590 Adaptor, 9-pin D PIug to 25-pin D Socket 08-05086-001 08-05086-006 Cable, Data Interface, 2 m Cable, Data Interface, 6 m 08-06422-001 Cable, 2110 Manpack to 3012 Modem, 1 m 15-04104-## User Guide, HF Data Modem 3012 Printed User Guide for the 3012 HF Data Modem. See page 165, Language Support for translations of this guide. 08-05980-001 UUPlus™ Email for HF Client Software Single user access to UUPlusTM Email for HF Server Software. For use with the 3012 or 3212 HF Data Modems. 08-05981-001 UUPlus™ Email for HF Server Software Email server with support for up to 25 remote or local users and Internet email access. For use with the 3012 or 3212 HF Data Modems. ## denotes language version Page 148 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email for 2110 3212 HF DATA MODEM (NO CABLES) PRODUCT 3212 System Requirements PART NO. MODEM-3212-NC DESCRIPTION 3212 HF Data Modem (No Cables) The 3212 HF Data Modem provides reliable and cost-effective computer text and data communication capabilities for organisations operating in remote areas with little or no telecommunications infrastructure. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. 3212 HF Data Modem (No Cables) COMPRISING: 08-06274-001 08-04515-001 30-11208-000 15-04146-CD • • • • 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) STANDARD FEATURES: • Up to 7200 bit/s error free on-air data rate without compression • Backwards compatible with Codan 3012 HF Data Modem • Designed to operate on standard bandwidth commercial HF channels • In-built DC isolation on all available ports • Modem control via RS232 or ethernet port AVAILABLE OPTIONS: • Support for UUPlus™ Email for HF Client or Server software, see page 144, UUPlus™ Software. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 149 Data & Email for 2110 3212 HF DATA MODEM FOR 2110 WITH 2 M RS232 CABLE 3212 HF Data Modem for 2110 with 2 m RS232 Cable PRODUCT DESCRIPTION PART NO. MODEM-3212-2110-2M 3212 HF Data Modem for 2110 with 2 m RS232 Cable This configuration consists of a 3212 HF Data Modem, 2 m Serial Cable, and 1 m 2110 Manpack to 3212 Modem Cable. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. COMPRISING: Page 150 08-06274-001 08-04515-001 30-11208-000 15-04146-CD 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) 08-06359-002 Serial D9M-D9F Isol Shield Cable, 2 m 08-06786-001 2110 Manpack to 3212 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Data & Email for 2110 3212 HF DATA MODEM FOR 2110 WITH 6 M RS232 CABLE 3212 HF Data Modem for 2110 with 6 m RS232 Cable PRODUCT DESCRIPTION PART NO. MODEM-3212-2110-6M 3212 HF Data Modem for 2110 with 6 m RS232 Cable This configuration consists of a 3212 HF Data Modem, 6 m Serial Cable, and 1 m 2110 Manpack to 3212 Modem Cable. The 3212 HF Data Modem uses waveforms derived from Military Standard (MIL-STD) waveforms, which are based on STANAG 4539 and modified to provide optimal performance over commercial channel bandwidths. COMPRISING: 08-06274-001 08-04515-001 30-11208-000 15-04146-CD 3212 HF Data Modem Earth Wire, 0.5 m Self Adhesive Rubber Feet (x4) 3212 HF Data Modem User Guide on CDROM (English) 08-06359-006 Serial D9M-D9F Isol Shield Cable, 6 m 08-06786-001 2110 Manpack to 3212 Modem Cable, 1 m Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 151 Data & Email for 2110 3212 ACCESSORIES PRODUCT 3212 Accessories PART NO. 15-00136 DESCRIPTION Cradle, HF Data Modem Vehicle Mounting 3212 Accessories Page 152 78-01031 Adaptor, USB to DB-9, Serial USB V1.1 compliant and supports Microsoft WindowsTM 2000/ XP/Vista/WIN7. 60-00098-590 Adaptor, 9-pin D PIug to 25-pin D Socket 39-79150-080 Ferrite Bead Clamp 08-06359-002 08-06359-006 Cable, Serial D9M-D9F Isol Shield, 2 m Cable, Serial D9M-D9F Isol Shield, 6 m 67-90800 67-90801 Cable, Ethernet Crossover CAT-5E, 2 m Red Cable, Ethernet Crossover CAT-5E, 10 m Red 67-90802 67-90803 Cable, Ethernet Straight CAT-5E, 2 m Blue Cable, Ethernet Straight CAT-5E, 10 m Blue 08-06786-001 Cable, 2110 Manpack to 3212 Modem, 1 m 15-04146-EN User Guide, 3212 HF Data Modem (English) Printed User Guide for the 3212 HF Data Modem. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Crosspatch™ for 2110 CROSSPATCH™ FOR 2110 PRODUCT Crosspatch™ for 2110 PART NO. XPATCH-2110 DESCRIPTION 3031 Crosspatch™ for 2110 Codan’s leading edge 3031 CrosspatchTM enables you to carry ‘HF on your belt’ using a VHF/UHF radio and a Codan NGT™ Transceiver. It is the practical, effective and affordable solution for any organisation that needs to extend their current HF or VHF/UHF networks. COMPRISING: 08-06730-002 08-06766-001 15-04148-CD 06-02489-EN 15-00145 CROSSPATCH™ ACCESSORIES PRODUCT • • • • • 3031 VHF/UHF to HF Crosspatch™ for 2110 3031 to VHF/UHF Transceiver Generic Cable, 2 m CrosspatchTM 3031 CD Package (English) CrosspatchTM 3031 Quick Reference Cards, English (x2) CrosspatchTM 3031 Installation Kit Crosspatch™ Accessories PART NO. DESCRIPTION 08-06766-001 Cable, 3031 to VHF/UHF Transceiver Generic 06-02489-EN Quick Reference Card, Crosspatch™ 3031 (English) 15-04148-EN User Guide, Crosspatch™ 3031 (English) Printed User Guide for the 3031 Crosspatch. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 153 Crosspatch™ for 2110 This page has been intentionally left blank. Page 154 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antenna Accessories LONG WIRE & DIPOLES Long Wire & Dipoles PRODUCT PART NO. 15-00454 Long Wire & Dipoles DESCRIPTION Ant, Long Wire and Adaptor 25 W PEP (1.6–30 MHz) Lightweight Kevlar reinforced Tactical Long Wire antenna. Includes: throw rope, antenna adaptor, winding spool, anchor peg and antenna deployment quick reference card. NET WEIGHT: 0.44 kg (0.97 lbs) 15-00458 Ant, End-fed Broadband 25 W PEP (3–30 MHz) Lightweight Kevlar reinforced End-fed Broadband Dipole Antenna. Includes: 3 m (10') coaxial feeding cable terminated with BNC connectors with protective caps, broadband antenna balun, throw rope, counterpoise kit, winding spool, anchor peg and antenna deployment quick reference card. NET WEIGHT: 1.1 kg (2.43 lbs) 15-00456 Ant, Broadband Dipole 25 W PEP (3–30 MHz) Lightweight Kevlar reinforced Tactical Broadband Dipole Antenna. Includes: 10 m (30') coaxial feeding cable terminated with BNC connectors with protective caps, broadband antenna balun, two lots of termination resistors, throw ropes, counterpoise kits, winding spools, anchor pegs and antenna deployment quick reference card. NET WEIGHT: 2.6 kg (5.73 lbs) 15-00455 Ant, Wire Dipole 25 W PEP (3–30 MHz) Lightweight Kevlar reinforced Tactical Dipole Antenna with tactile length markings. Includes: 10 m (30') coaxial feeding cable terminated with BNC connectors with protective caps, dipole antenna balun, throw rope, antenna adaptor, winding spools, anchor peg and antenna deployment quick reference card. NET WEIGHT: 2.7 kg (5.95 lbs) 15-00457 NET WEIGHT: 3.3 kg (7.28 lbs) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Ant, Dipole and Broadband kit 25 W PEP (2–30 MHz) Lightweight Kevlar reinforced Universal HF Dipole and HF Broadband Dipole Antenna kit. Includes: 10 m (30') coaxial feeding cable terminated with BNC connectors with protective caps, broadband antenna balun, dipole antenna balun, two lots of termination resistors, throw ropes, counterpoise kits, winding spools, anchor pegs and antenna deployment quick reference cards. Page 155 Antenna Accessories TACTICAL MAST Tactical Mast PRODUCT PART NO. 78-13035 DESCRIPTION Mast, Man-portable 6 m Tactical Lightweight, compact man-portable mast system. The kit includes, multi section mast, guy ropes, guy stakes, halyard, base plate stakes and installation instructions. This mast is most suitable for use with lightweight, low power (25 W) antennas used with the 2110 series Manpack Transceiver (see page 155, Long Wire & Dipoles). NOTE: • The 6 m mast is not suitable for use with full size 125 W/ 1 kW Broadband Antennas. • Certain Manpack Transceiver antennas may require more than one mast. Please check specific mast requirements for each antenna before ordering. NET WEIGHT: 5.0 kg (11.02 lbs) WHIP ANTENNAS Whip Antennas PRODUCT PART NO. DESCRIPTION 15-00452 Ant, 3 m (10’) Collapsible Whip 25 W Lightweight collapsible 6 section whip antenna with flexible gooseneck. 15-00453 Ant, 1.5 m (5’) Tape Whip 25 W Foldable tape whip antenna with flexible gooseneck. 15-00459 Ant, 1.5 m (5’) Knock Over Whip 25 W Lightweight collapsible 3 section knock over whip antenna with flexible gooseneck. NET WEIGHT: 0.4 kg (0.88 lbs) NET WEIGHT: 0.25 kg (0.55 lbs) NET WEIGHT: 0.28 kg (0.62 lbs) CABLES Cables PRODUCT PART NO. Page 156 DESCRIPTION 08-07010-006 Antenna Tuner Control Cable, 6 m Interface cable for direct connection of antenna tuner to 19-pin front panel connector on 2110 (not suitable for 2110v). 08-06357-001 BNC to UHF Coaxial Cable, 1 m Used to adapt BNC connector on 2110/2110v to UHF socket. Requires additional coaxial cable length for connection to antenna, see page 109, Coaxial Cables. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Antenna Accessories EARTHING Earthing PRODUCT PART NO. DESCRIPTION 15-00446 Counterpoise 4-wire kit Lightweight counterpoise and earthing kit. 15-00462 Anchor peg Used in antenna kits to anchor the antenna wires. 08-06259-001 Earth Wire with Clip Earthing wire 1 m (3') with spring clip. NET WEIGHT: 0.16 kg (0.35 lbs) NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 0.05 kg (0.11 lbs) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 157 Antenna Accessories This page has been intentionally left blank. Page 158 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Battery & Charger Accessories BATTERIES Batteries PRODUCT PART NO. 08-06185-001 DESCRIPTION Battery Pack 12 V 8Ah NiMH Waterproof 2110 Transceiver battery pack with 12 V, 8Ah rechargeable Nickel Metal Hydride battery and battery management controller. Recharges: ~500 (80% capacity) Useable hours: ~30 hrs (using Rx/Tx 9:1) NET WEIGHT: 2.1 kg (4.63 lbs) 08-06186-001 Battery Pack 12 V 13Ah NiMH Waterproof 2110 Transceiver battery pack with 12 V, 13Ah rechargeable Nickel Metal Hydride battery and battery management controller. Recharges: ~500 (80% capacity) Useable hours: ~50 hrs (using Rx/Tx 9:1) NET WEIGHT: 2.9 kg (6.39 lbs) 08-07009-001 Battery Pack 12 V 17 Ah LiFePO4 Waterproof 2110 Transceiver battery pack with 12 V, 17 Ah rechargeable battery using lithium iron phosphate chemistry that is safe and has excellent shelf life. 2000 (80% capacity) Recharges: Useable hours: 65 hrs (using Rx/Tx 9:1) NET WEIGHT: 2.5 kg (5.5 lbs) NOTE: This battery is classified as dangerous goods and may impact freight cost and method. Please contact your Codan Sales Representative for further details. DC-DC VOLTAGE CONVERTER PRODUCT DC-DC Voltage Converter PART NO. 15-00576 DC-DC Voltage Converter DESCRIPTION Voltage Regulator (24 V to 12 V operation 7 A) Enables the operation of 2110 series Transceivers in 24/ 26 V based systems. Protected from faults such as voltage spikes, overload, short circuits and low voltage input. The unit automatically resets once a fault is removed. Nominal Input: 24 V DC Nominal Output: 12 V @ 7 A Efficiency: Greater than 90% at full load NOTE: The voltage regulator is not waterproof. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 159 Battery & Charger Accessories CHARGERS Chargers PRODUCT PART NO. 15-00578 DESCRIPTION 2110 Hand-powered Battery Charger A portable hand-powered battery charger that is compact and lightweight, and encased in a robust and waterproof aluminium housing. The charger comes with easy to use accessories for simple operation, and a convenient carrying case. A suitable charger output cable must be ordered separately, see page 161, Charger Output Cables. NET WEIGHT: 3.7 kg (8.16 lbs) 15-00577 2110 Solar Battery Charger (Black) A portable solar-powered 20 W battery charger that uses solid state, thin film solar technology to meet your mobile power needs. It is lightweight, weatherproof and UV resistant, and durable with a tough rip-stop nylon backing. A suitable charger output cable must be ordered separately, see page 161, Charger Output Cables. NET WEIGHT: 1 kg (2.2 lbs) 15-00581 2110 Solar Battery Charger (Digital Camo) A portable solar-powered 20 W battery charger that uses solid state, thin film solar technology to meet your mobile power needs. It is lightweight, weatherproof and UV resistant, and durable with a tough rip-stop nylon backing. A suitable charger output cable must be ordered separately, see page 161, Charger Output Cables. CHARGER MODULES Charger Modules PRODUCT PART NO. 78-02007 NET WEIGHT: 0.25 kg (0.55 lbs) DESCRIPTION Battery Charger AC-DC 3121 Low noise 2110 battery charger (90–240 V AC input, 15.5 V @ 1 A output). Suitable for charging while operating the transceiver, NOTE: Suitable AC input cable (with AUS, UK, USA or EU plug) and output cable for AC-DC 3121 charger module must be ordered separately. Continued on the next page Page 160 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Battery & Charger Accessories CHARGER MODULES CONT. Charger Modules PRODUCT PART NO. 78-02012 78-02008 NET WEIGHT: 0.24 kg (0.53 lbs) PRODUCT Battery Charger AC-DC 3123 Fast 2110 battery pack charger (90–240 V AC input, 15.5 V @ 3 A output) with output cable. Suitable for direct connection to the battery pack only. NOTE: Suitable AC input cable (with AUS, UK, USA or EU plug) must be ordered separately. NET WEIGHT: 0.4 kg (0.88 lbs) CHARGER OUTPUT CABLES DESCRIPTION Battery Charger DC-DC 3122 Low noise 2110 battery charger (12–60 V DC input, 15.5 V @ 1 A output). Suitable for charging while operating the transceiver. NOTE: Suitable DC input cable (with vehicle lighter plug or spring clips adaptor) and output cable for DC-DC 3122 charger module must be ordered separately. Charger Output Cables PART NO. 08-06215-001 DESCRIPTION Cable, charger O/P, 19way Used to charge the 2110 series Transceivers via the front panel. Can be used with 3121 and 3122 Battery Chargers, and handcrank and solar chargers. Charger Output Cables NET WEIGHT: 0.08 kg (0.18 lbs) 08-06738-001 Cable, charger O/P, 5way Used to charge the 2110v transceiver via the front panel. Can be used with 3121 and 3122 Battery Chargers, and handcrank and solar chargers. 08-06214-001 Cable, Charger O/P, 6way Used to charge the battery directly. Can be used with 3121 and 3122 Battery Chargers, and handcrank and solar chargers. NET WEIGHT: 0.08 kg (0.18 lbs) NET WEIGHT: 0.08 kg (0.18 lbs) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 161 Battery & Charger Accessories CHARGER INPUT CABLES AC PRODUCT Charger Input Cables AC PART NO. 67-90200 DESCRIPTION Cable, 2C AUS IEC C7 2 m IEC 2-wire mains cable with AUS plug. Charger Input Cables AC NET WEIGHT: 0.1 kg (0.22 lbs) 67-90201 Cable, 2C UK IEC C7 2 m IEC 2-wire mains cable with UK plug. 67-90202 Cable, 2C USA IEC C7 2 m IEC 2-wire mains cable with USA plug. 67-90203 Cable, 2C EU IEC C7 2 m IEC 2-wire mains cable with EU plug. NET WEIGHT: 0.13 kg (0.29 lbs) NET WEIGHT: 0.16 kg (0.35 lbs) NET WEIGHT: 0.09 kg (0.198 lbs) CHARGER INPUT CABLES DC Charger Input Cables DC PRODUCT PART NO. DESCRIPTION 08-06216-001 Cable, DC Charger I/P, Lighter Adaptor DC input cable to connect an in-vehicle lighter socket to DC-DC 3122 charger module. 08-06217-001 Cable, DC Charger I/P, Clips Adaptor DC input cable with spring clips to connect DC power source to DC-DC 3122 charger module. NET WEIGHT: 0.11 kg (0.24 lbs) NET WEIGHT: 0.15 kg (0.33 lbs) Page 162 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Backpack & Mounting Accessories BACKPACKS Backpacks PRODUCT PART NO. 15-00216-001 DESCRIPTION Backpack, External Frame Heavy duty backpack with external frame and ergonomic shoulder harness with ventilation panel for comfort. It has side, bottom and front pockets for transceiver accessories, reference materials, and personal items. The modular external frame allows for additional loads of up to 50 kg. Made from 1000 Denier Black bulked filament nylon, black co-polymer frame. NET WEIGHT: 4.3 kg (9.48 lbs) 15-00218 Backpack, Softpack Lightweight, compact and comfortable backpack providing storage for transceiver, all accessories as well as personal items. Made from Black Cordura. NET WEIGHT: 1.23 kg (2.71 lbs) Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 163 Backpack & Mounting Accessories MOUNTING ACCESSORIES Mounting Accessories PRODUCT PART NO. DESCRIPTION 15-00139 Cradle, 2110/2110v with Screws Heavy duty docking cradle used to secure the 2110 or 2110v transceiver in a vehicle. With quick release latches and screw kit, the radio can be easily docked with the battery pack attached. 15-00140 Cradle, 2110 with Interface Adpaptor Transceiver cradle (part number 15-00139) plus an interface adaptor for external antenna, GPS, data interfaces, and DC battery charger. Includes a speaker amplifier and external speaker, and can be adapted to interface with a VP-116 Voice Privacy Unit via an NGT™ VP-116 Interface cable (part number 08-06213-001). NET WEIGHT: 1.7 kg (3.75 lbs) NOTE: Cannot be used with the 2110v Transceiver. NET WEIGHT: 2.5 kg (5.51 lbs) 15-00141 NOTE: Cannot be used with the 2110v Transceiver. NET WEIGHT: 1.9 kg (4.19 lbs) 15-00143 15-00144 Page 164 2110 External DC for Cradle Backpanel for the transceiver cradle that provides DC connection for the transceiver directly to the vehicle battery. NOTE: • The transceiver cradle is only shown for illustration purposes. • Voltage regulator (part number 15-00576) is available for 24 V vehicle operation. See page 159, DC-DC Voltage Converter. NET WEIGHT: 0.3 kg (0.66 lbs) NET WEIGHT: 1.7 kg (3.75 lbs) Cradle, 2110 with 9350 Interface Suitable for interfacing with the 9350 Automatic Tuning Whip Antenna and a DC battery charger. For 9350 ordering details, see page 91, 9350 Automatic Tuning Whip Antenna. 2110 External DC Vehicle Kit Complete vehicle installation kit incorporating the external DC backpanel (part number 15-00143). It provides DC connection for the transceiver directly to the vehicle battery. NOTE: Voltage regulator (part number 15-00576) is available for 24 V vehicle operation. See page 159, DC-DC Voltage Converter. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Language Support ENGLISH MANUALS PRODUCT English Manuals PART NO. DESCRIPTION 15-04177-EN Getting Started Guide, Envoy™ Transceiver, includes Reference Manual on CDROM 06-02809-EN Quick Reference Card, Envoy X1 and X2 15-04127-EN Getting Started Guide, NGT™ Transceiver, includes Reference Manual on CDROM 15-04140-EN Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM 15-04137-EN Getting Started Guide, NGT™ ASR Transceiver, includes Reference Manual on CDROM 15-04136-EN Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM 15-04104-EN User Guide, HF Data Modem 3012 a 15-04104-CD User Guide, HF Data Modem 3012, on CDROM Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 165 Language Support ENGLISH MANUALS CONT. PRODUCT English Manuals PART NO. DESCRIPTION 15-04146-EN User Guide, 3212 HF Data Modem 15-04146-CD User Guide, 3212 HF Data Modem, on CDROM 15-04148-EN User Guide, Crosspatch™ 3031 15-04148-CD User Guide, Crosspatch™ 3031, on CDROM 15-04131-EN Reference Manual, High Power Amplifiers 3061/3062 15-04156-EN User Guide, 3033 Telephone Interconnect 15-04156-CD User Guide, 3033 Telephone Interconnect, on CDROM 15-04102-EN Reference Manual, Remote Control NGT™ Systems Continued on the next page Page 166 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Language Support ENGLISH MANUALS CONT. PRODUCT English Manuals PART NO. DESCRIPTION 15-04125-EN Reference Manual, Split-site Remote Control NGT™ Systems 15-04142-EN Installation Handbook, Automatic Tuning Whip Antenna 9350 15-04143-EN Repair Guide, NGT™ Transceiver 15-04143-CD Repair Guide, NGT™ Transceiver, on CDROM 15-04139-EN Repair Guide, Manpack Transceiver 2110 series 15-04139-CD Repair Guide, Manpack Transceiver 2110 series on CDROM 15-60012 Installation Handbook, 3040 Automatic Whip Antenna, c/w antenna connector sealing kit Continued on the next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 167 Language Support FRENCH MANUALS PRODUCT Page 168 French Manuals PART NO. DESCRIPTION 15-04127-FR Getting Started Guide, NGT™ Transceiver, includes Reference Manual on CDROM 15-04140-FR Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM 15-04136-FR Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM 15-04104-FR User Guide, HF Data Modem 3012 15-04102-FR Reference Manual, Remote Control NGT™ Systems 15-04142-FR Installation Handbook, Automatic Tuning Whip Antenna 9350 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Language Support SPANISH MANUALS PRODUCT Spanish Manuals PART NO. DESCRIPTION 15-04127-ES Getting Started Guide, NGT™ Transceiver, includes Reference Manual on CDROM 15-04137-ES Getting Started Guide, NGT™ ASR Transceiver, includes Reference Manual on CDROM 15-04140-ES Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM 15-04136-ES Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM 15-04131-ES Reference Manual, High Power Amplifiers 3061/3062 15-04142-ES Installation Handbook, Automatic Tuning Whip Antenna 9350 06-02809-ES Quick Reference Card, Envoy X1 and X2 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 169 Language Support ARABIC MANUALS PRODUCT Arabic Manuals PART NO. 15-04140-AR Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM 15-04136-AR Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM DARI MANUALS PRODUCT Arabic Manuals PART NO. 06-02809-FA PORTUGUESE MANUALS PRODUCT PART NO. RUSSIAN MANUALS Quick Reference Card, Envoy X1 and X2 DESCRIPTION Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM Arabic Manuals PART NO. 06-02809-RU Page 170 DESCRIPTION Portuguese Manuals 15-04140-PT PRODUCT DESCRIPTION DESCRIPTION Quick Reference Card, Envoy X1 and X2 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 2110-TCVR 2110 SSB Transceiver Kit B2 5.0 2110-TCVR-PATROL 2110 Patrol Configuration CMR 11.0 2110-TCVR-EXP 2110 Explorer Configuration AA + BPK 14.5 2110-TCVR-HS 2110 Homeland Security Configuration AA + BPK 16.0 ANT-3040-NC 3040 Automatic Tuning Whip (No Cables) B + Tube 5.07 ANT-3040-6M 3040 Automatic Tuning Whip with 6 m Cables B + Tube 5.75 ANT-3042-NC 3042 HF Antenna Tuner with 6 m Cables B 4.12 ANT-3042-6M 3042 HF Antenna Tuner (No Cables) B 3.6 ANT-9350-NC 9350 Automatic Tuning Whip (No Cables) D 8.6 ANT-9350-6M 9350 Automatic Tuning Whip with 6 m Cables D 9.28 CONTROL-POINT-ASR6M NGTTM ASR Control Point Kit B 2.5 CONTROL-POINT-SR6M NGTTM SR Control Point Kit B 2.5 ENVOY-X1-BASE Envoy™ X1 Base Station Configuration B, PSU, T 14.02 ENVOY-X1-BASE-AUS Envoy™ X1 Base Configuration for Australia B, PSU, T 14.02 ENVOY-X1-CONS-AUS Envoy™ X1 Base (with Console) Configuration for Australia B, PSU, T 15.12 ENVOY-X1-MOB Envoy™ X1 Mobile Configuration B 4.23 ENVOY-X1-MOB-3040AUS Envoy™ X1 Mobile (3040) Configuration for Australia B, B, TUBE 14.58 ENVOY-X1-MOB-9350AUS Envoy™ X1 Mobile (9350) Configuration for Australia B, D 16.46 ENVOY-X1-MOBEXPLORER-AUS Envoy™ X1 Explorer Mobile Configuration for Australia B, B, TUBE 14.45 ENVOY-X1-MOBVENTURER-AUS Envoy™ X1 Venturer Mobile Configuration for Australia B, D 15.06 ENVOY-X1-TCVR Envoy™ X1 Transceiver B 4.23 ENVOY-X1-TCVR-AUS Envoy™ X1 Transceiver for Australia B 4.23 ENVOY-X2-BASE Envoy™ X2 Base Station Configuration B 4.23 ENVOY-X2-BASE-AUS Envoy™ X2 Base Configuration for Australia B, PSU, T 14.02 ENVOY-X2-CONS-AUS Envoy™ X2 Base (with Console) Configuration for Australia B, PSU, T 15.12 ENVOY-X2-MOB Envoy™ X2 Mobile Configuration B 4.23 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 171 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) ENVOY-X2-MOB-3040AUS Envoy™ X2 Mobile (3040) Configuration for Australia B, B, TUBE 14.58 ENVOY-X2-MOB-9350AUS Envoy™ X2 Mobile (9350) Configuration for Australia B, D 16.46 ENVOY-X2-TCVR Envoy™ X2 Transceiver B 4.23 ENVOY-X2-TCVR-AUS Envoy™ X2 Transceiver for Australia B 4.23 HIGH-PWR-500 3061 500 W Power Amplifier HPPA1, HPPA2 35.0 HIGH-PWR-1000 3062 1 kW Power Amplifier HPPA1, HPPA2 47.0 MODEM-3012-NC 3012 HF Data Modem (No Cables) PSU 2.99 MODEM-3012-NGT2M 3012 HF Data Modem for NGTTM with 2 m RS232 Cable PSU 3.37 MODEM-3012-NGT6M 3012 HF Data Modem for NGTTM with 6 m RS232 Cable PSU 3.59 MODEM-3012-21106M 3012 HF Data Modem for 2110 with 6 m RS232 Cable PSU 3.56 MODEM-3212-NC 3212 HF Data Modem (No Cables) B 3.0 MODEM-3212-NGT-2 M 3212 HF Data Modem for NGTTM with 2 m RS232 Cable B 4.39 MODEM-3212-NGT-6 M 3212 HF Data Modem for NGTTM with 6 m RS232 Cable B 5.74 MODEM-3212-21102M 3212 HF Data Modem for 2110 with 2 m RS232 Cable B 4.74 MODEM-3212-21106M 3212 HF Data Modem for 2110 with 6 m RS232 Cable B 5.74 NGT-AR-BASE-CON NGT™ AR Base Configuration for Australia B 15.47 NGT-AR-MOB NGT™ AR Mobile Configuration for Australia B, D 16.46 NGT-AR-MOB-3040 NGT™ AR Mobile (3040) Configuration for Australia B, B, TUBE 14.58 NGT-AR-TCVR NGT™ AR Transceiver Configuration for Australia B 7.0 NGT-ASR-BASE NGTTM ASR Base Station Configuration A, PSU, T463 20.0 NGT-ASR-MOB NGTTM ASR Mobile Configuration B, D 18.0 Page 172 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) NGT-ASR-TCVR NGTTM ASR Transceiver B 7.0 NGT-SR-BASE NGTTM SR Base Station Configuration A, PSU, T463 20.0 NGT-SR-MOB NGTTM SR Mobile Configuration B, D 18.0 NGT-SR-TCVR NGTTM SR Transceiver B 7.0 NGT-SRX-BASE NGTTM SRx Base Station Configuration A, PSU, T463 20.0 NGT-SRX-MOB NGTTM SRx Mobile Configuration B, D 18.0 NGT-SRX-TCVR NGTTM SRx Transceiver Configuration B 7.0 NGT-SRX-BASE-AUS NGT SRx Base Configuration for Australia B, T643, PSU 14.47 NGT-SRX-TCVR-AUS NGTTM SRx Transceiver Configuration for Australia B 5.04 NGT-SRX-MOB-3040 NGT™ SRx Mobile (3040) Configuration for Australia B, B, TUBE 14.58 NGT-SRX-MOB-AUS NGT™ SRx Mobile (9350) Configuration for Australia B, D 16.46 REMOTE-ENVOY-ETH Envoy Remote Control Accessories — Ethernet B 1.6 REMOTE-NRI-CTRL2W NGT™ Remote Interface Control Site — 2 Wire Interface B 4.63 REMOTE-NRI-TCVR2W NGT™ Remote Interface Transceiver Site — 2 Wire Interface B 4.16 REMOTE-SPLIT-CTRL8571-2W NGT™ Split-site Control Site — 2 Wire Interface B 6.99 REMOTE-SPLIT-RX8571-2W NGT™ Split-site Receive Site — 2 Wire Interface B 6.49 REMOTE-SPLIT-TX8571-2W NGT™ Split-site Transmit Site — 2 Wire Interface B 6.39 REMOTE-SPLIT-TXRX8571-2W NGT™ Split-site Transmit & Receive — 2 Wire Interface B.B 13.0 REMOTE-SPLIT-CTRL8571-4W NGT™ Split-site Control Site — 4 Wire Interface B 6.91 REMOTE-SPLIT-RX8571-4W NGT™ Split-site Receive Site — 4 Wire Interface B 6.41 REMOTE-SPLIT-TX8571-4W NGT™ Split-site Transmit Site — 4 Wire Interface B 6.31 REMOTE-SPLIT-TXRX8571-4W NGT™ Split-site Transmit & Receive Site — 4 Wire Interface B.B 13.0 RTI-3033-NGT 3033 Telephone Interconnect HPA 10.0 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 173 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) XPATCH-NGT 3031 CrosspatchTM for NGT™ L 0.84 XPATCH-2110 3031 CrosspatchTM for 2110 L 0.84 05-06374 Earth Braid, 1.5 m M 0.5 06-02489-EN Quick Reference Card, Crosspatch™ 3031 (English) L 0.32 06-02809-EN Quick Reference Card, Envoy™ (English) L 0.32 08-01233 Strain Relief L 0.5 08-01503-002 Cable, Coax Assembly, UHF Type Connectors, RG58, 2 m M 0.5 08-01503-006 Cable, Coax Assembly, UHF Type Connectors, RG58, 6 m L 0.5 08-01503-008 Cable, Coax Assembly, UHF Type Connectors, RG58, 8 m L 0.5 08-01503-030 Cable, Coax Assembly, UHF Type Connectors, RG58, 30 m B 3.0 08-03255 Cable, Battery, 6 m L 0.5 08-04146-001 Cable, 6-way Phone M 0.5 08-04284 Cable, Phone Plug Adaptor Modular to 604 Plug M 0.5 08-04515-001 Earth Wire, 0.5 m M 0.5 08-04835-013 Tuner, 9103 Automatic Antenna with 10 m Cables B 4.0 08-04835-015 Tuner, 9103 Automatic Antenna with 30 m Cables B 4.0 08-04971-010 Cable, Coax Assembly, UHF Type Connectors, RG213, 10 m A 2.0 08-04971-030 Cable, Coax Assembly, UHF Type Connectors, RG213, 30 m A 5.0 08-04971-050 Cable, Coax Assembly, UHF Type Connectors, RG213, 50 m A 7.0 08-04971-100 Cable, Coax Assembly, UHF Type Connectors, RG213, 100 m A 20.0 08-05063-001 9350 Main Assembly D 7.0 08-05086-001 Cable, Data Interface, 2 m L 0.5 08-05086-006 Cable, Data Interface, 6 m L 0.5 08-05123-001 Cable, NSP Interface M 0.5 08-05140-001 9350 Spring L 1.0 08-05288-009 Rack Cabinet, 9RU High, 19" Format, 500 mm Deep R 23.4 08-05288-012 Rack Cabinet, 12RU High, 19" Format, 500 mm Deep R 22.0 08-05288-018 Rack Cabinet, 18RU High, 19" Format, 500 mm Deep H 24.0 08-05399-001 Cable, Battery Paralleling (+ve) M 0.5 Page 174 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 08-05399-002 Cable, Battery Paralleling (-ve) M 0.5 08-05610-001 Cable, CIB Interface, 0.5 m M 0.5 08-05610-002 Cable, CIB Interface, 2 m M 0.5 08-05610-006 Cable, CIB Interface, 6 m P4 0.5 08-05610-030 Cable, CIB Interface, 30 m 1/2B 3.0 08-05627-002 Cable, NGTTM /EnvoyTM to 9350/304X Control, 2 m L 0.2 08-05627-006 Cable, NGTTM /EnvoyTM to 9350/304X Control, 6 m L 0.5 08-05627-008 Cable, NGTTM /EnvoyTM to 9350/304X Control, 8 m L 0.5 08-05627-010 Cable, NGTTM /EnvoyTM to 9350/304X Control, 10 m PSU 0.5 08-05627-020 Cable, NGTTM /EnvoyTM to 9350/304X Control, 20 m PSU 1.2 08-05627-030 Cable, NGTTM /EnvoyTM to 9350/304X Control, 30 m B 3.0 08-05628-001 NGTTM SR 2010 RF Unit B 5.0 08-05628-004 NGTTM VR 2011 RF Unit B 5.0 08-05628-007 NGTTM ASR 2010 RF Unit B 5.0 08-05628-009 NGTTM SRx 2012 RF Unit B 5.0 08-05629-001 NGTTM SR 2020 Handset L 0.3 08-05629-007 NGTTM ASR 2020 Handset L 0.3 08-05629-009 NGTTM SRx 2020 Handset L 0.3 08-05630-001 NGTTM SR 2030 Junction Box 1/2B 0.5 08-05630-005 Split-site Interface Control Junction Box 1/2B 0.5 08-05630-007 NGTTM ASR 2030 Junction Box 1/2B 0.5 08-05712-001 Cable, NGTTM to 3012 Modem, 1 m L 0.5 08-05712-006 Cable, NGTTM to 3012 Modem, 6 m L 0.72 08-05837-002 Cable, Coax Assembly, UHF to N-type Connectors, RG58, 2m L 0.125 08-05837-006 Cable, Coax Assembly UHF to N-type Connectors, RG58, 6m PSU 0.285 08-05837-010 Cable, Coax Assembly UHF to N-type Connectors, RG58, 10 m PSU 0.5 08-05837-020 Cable, Coax Assembly UHF to N-type Connectors, RG58, 20 m PSU 1.1 08-05847-001 Interface Adaptor M 0.2 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 175 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 08-05858-001 Cable, NRI to Line Modem M 0.5 08-05859-001 Cable, Power NRI to Line Modem M 0.5 08-05864-001 3030 NGTTM Remote Interface Unit B 2.0 08-05868-001 Cable, Power to RF Unit and NRI M 0.5 08-05877-004 3012 HF Data Modem B 2.74 08-05920-001 Cable, DC Extension, 1 m M 0.2 08-05956-001 Cable, High Power Amplifier Controller L 0.5 08-05974-001 3061 500 W Power Amplifier HPPA1 20.0 08-05975-001 3062 1 kW Power Amplifier HPPA1 27.0 08-05980-001 UUPlusTM Email for HF Client Software 1/2B 0.5 08-05981-001 UUPlusTM Email for HF Server Software 1/2B 0.5 08-05989-001 Cable, Power Adaptor, Split-site M 0.5 08-05990-001 Cable, 8571 Split-site Remote Interface to NGTTM M 0.5 08-05994-001 8571 NGTTM Remote Control Interface B 2.0 08-06022-001 Envoy™/NGT™ Handset Control Cable, 6 m M 0.4 08-06067-001 3061 500 W Power Supply Unit HPPA2 14.0 08-06102-001 3062 1 kW Power Supply Unit HPPA2 17.0 08-06130-001 Basic High Power Rack Configuration H 90 08-06130-002 Remote Control, High Power Rack Configuration H 90 08-06130-003 Remote Control and Data Modem High Power Rack Configuration H 90 08-06130-004 Split-site Remote Control High Power Rack Configuration H 90 08-06155-001 2110 SSB Tcvr Unit (1.5 ppm) PSU 3.5 08-06155-002 2110 SSB Tcvr Unit (0.5 ppm) PSU 3.5 08-06155-003 2110v SSB Tcvr Unit (1.5 ppm) PSU 3.5 08-06185-001 Battery Pack 12 V 8Ah NiMH 1/2B 2.6 08-06186-001 Battery Pack 12 V 13Ah NiMH 1/2B 3.4 08-06213-001 Cable, VP-116 Interface M 0.5 08-06214-001 Cable, Charger O/P, 6way M 0.3 08-06215-001 Cable, charger O/P, 19way M 0.3 Page 176 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 08-06216-001 Cable, DC Charger I/P, Lighter Adaptor M 0.4 08-06217-001 Cable, DC Charger I/P, Clips Adaptor M 0.4 08-06222-001 NGTTM ASR VP-116 Junction Box 1/2B 0.5 08-06237-001 Cable, 2110 Prog 19way MIL-D9F M 0.5 08-06259-001 Earth Wire with Clip M 0.3 08-06274-001 3212 HF Data Modem B 4.34 08-06330-001 Cable, NGTTM to Q9600 Modem, 1 m M 0.5 08-06356-001 Cable, NGT™/Envoy™ to 3212 Modem, 1 m L 0.42 08-06356-006 Cable, NGT™/Envoy™ to 3212 Modem, 6 m L 0.76 08-06357 Cable, BNC to UHF Coaxial, 1 m M 0.2 08-06359-002 Cable, Serial D9M-D9F Isol Shield Cable, 2 m M 0.4 08-06359-006 Cable, Serial D9M-D9F Isol Shield Cable, 6 m L 0.1 08-06360-002 Cable, 9-way to 9-way Serial, 2 m L 0.42 08-06360-006 Cable, 9-way to 9-way Serial, 6 m L 0.55 08-06361-002 Cable, Serial 25-way to 25-way, 2 m L 0.55 08-06361-006 Cable, Serial 25-way to 25-way, 6 m L 0.83 08-06380-001 Cable, Serial 6-way to D9F M 0.5 08-06422-001 Cable, 2110 Manpack to 3012 Modem, 1 m L 0.46 08-06454-001 NGTTM to MICOM Interface Box L 0.49 08-06730-001 3031 VHF/UHF to HF Crosspatch™ for NGT™ L 0.54 08-06730-002 3031 VHF/UHF to HF Crosspatch™ for 2110 L 0.59 08-06737-001 Cable, 2110v Prog 5way MIL-D9F M 0.5 08-06738-001 Cable, charger O/P, 5way M 0.3 08-06739-001 Tuner, SG235C 500 W PEP B 3.5 08-06740-030 Cable, SG235C Control, 30 m 1/2B 3.0 08-06766-001 Cable, 3031 to VHF/UHF Transceiver Generic, 2 m L 0.5 08-06786-001 Cable, 2110 Manpack to 3112 Modem, 1 m L 0.44 08-07000-001 EnvoyTM 2220 Handset L 0.3 08-07000-002 EnvoyTM 2221 Limited Keyset Handset L 0.3 08-07007-001 3040 Main Assembly B 5.0 08-07009-001 Battery Pack 12 V 17Ah LiFePO4 PSU 3.0 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 177 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 08-07010-006 Antenna Tuner Control Cable, 6 m L 1.0 08-07148-001 3040 Spring L 1.0 08-07204-001 EnvoyTM 2230 Desk Console 1/2B 1.1 08-07214-001 Cable, Envoy™ USB Programming M 0.04 08-07218-001 EnvoyTM X1 2210 RF Unit PSU 2.9 08-07218-002 EnvoyTM X2 2210 RF Unit 15-00112 Complete Vehicle Installation Kit B 2.5 15-00129 NGTTM Handset Cradle Kit M 0.5 15-00134 NGTTM Remote Control Earth Kit for the Remote Site L 0.5 15-00135 NGTTM Remote Control Earth Kit for the Control Site L 0.1 15-00136 Cradle, NGTTM RF Unit Mounting/3012 HF Data Modem B 2.3 15-00139 Cradle, 2110/2110v with Screws B 2.5 15-00140 Cradle, 2110 with Interface Adpaptor B 3.5 15-00141 Cradle, 2110 with 9350 Interface B 2.6 15-00143 2110 External DC for Cradle L 0.3 15-00144 2110 External DC Vehicle Kit 1/2B 2.1 15-00145 CrosspatchTM 3031 Installation Kit P1 0.12 15-00149 EnvoyTM Handset Cradle L 0.05 15-00158 Earth Mat for Base Whip Antenna, Ground Installations 406A 3.0 15-00159 Radial Ground Plane for Base Whip Antenna, Roof Installations B 6.0 15-00163 Earth Stake C 2.0 15-00164-010 19" Rack-mounting Frame for 8571 Split-site Remote Interface A 2.0 15-00172-001 NGTTM Universal 19" Rack-mounting Tray 3RU with Blank Front Panel F 2.0 15-00172-002 NGTTM /EnvoyTM Universal 19" Rack-mounting Tray 3RU, Front Panel with Speaker Grill and Mounting Holes F 2.5 15-00173 Set of 1RU + 2RU Blank Front Panels B 0.6 15-00176 19" Rack-mounting Frame suitable for 3020 Transceiver Supply, and 3012 or 3212 HF Data Modems T 2.39 15-00216 Backpack, External Frame BPK 5.5 15-00218 Backpack, Softpack B2 2.5 Page 178 2.9 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 15-00323 NVIS Antenna Kit C 2.0 15-00403 Ant, Tuned Long Wire (2–30 MHz) B 1.0 15-00406-001 Ant, Base Whip, Ground Mounting (9.5 m/31 ft Unloaded) 406 7.0 15-00406-002 Ant, Base Whip, Roof Mounting (9.5 m/31 ft Unloaded) 406A 7.0 15-00411-003 Ant, TFD411, 125 W, 2–30 MHz, 43 m T 6.0 15-00411-004 Ant, TFD411, 125 W, 2–30 MHz, 34 m T 6.0 15-00411-005 Ant, TFD411, 125 W, 2–30 MHz, 27 m T 6.0 15-00411-011 Ant, TFD411, 1000 W, 2–30 MHz, 34 m T 17.0 15-00411-012 Ant, TFD411, 1000 W, 2–30 MHz, 43 m T 17.0 15-00422-012 Mast, Guyed 12 m with Erection Kit M1, M2 47.0 15-00422-015 Mast, Guyed 15 m with Erection Kit M3, M4 51.0 15-00446 Counterpoise 4-wire kit M 0.5 15-00452 Ant, 3 m (10’) Collapsible Whip 25 W 1/2C 1.4 15-00453 Ant, 1.5 m (5’) Tape Whip 25 W 1/2C 1.3 15-00454 Ant, Long Wire and Adaptor 25 W PEP (1.6–30 MHz) L 0.8 15-00455 Ant, Wire Dipole 25 W PEP (3–30 MHz) 1/2B 3.2 15-00456 Ant, Broadband Dipole 25 W PEP (3–30 MHz) 1/2B 3.1 15-00457 Ant, Dipole and Broadband kit 25 W PEP (2–30 MHz) 1/2B 3.8 15-00458 Ant, End-fed Broadband 25 W PEP (3–30 MHz) 1/2B 1.6 15-00459 Ant, 1.5 m (5’) Knock Over Whip 25 W 1/2C 1.3 15-00462 Anchor peg L 0.4 15-00464 Lightning Arrestor M 0.5 15-00508 Voltage Regulator (24 V to 12 V operation 20 A) B 1.2 15-00531 Solar Power Supply 40 W SOLA 9.0 15-00532 Solar Power Supply 80 W SOLA 18.0 15-00533 Solar Power Supply 240 W 533A, C 44.0 15-00573 2110 Battery Charger AC 1 A L 0.7 15-00576 2110 Voltage Regulator (24 V to 12 V operation 7 A) L 0.98 15-00577 2110 Solar Battery Charger 1/2B 3.0 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 179 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 15-00578 2110 Hand-powered Battery Charger F 5.0 15-00602 Desk Console Headphones, NGT™ B 1.0 15-00649 External Speaker with 4 m Lead M 0.4 15-00662 Morse Key for Envoy™/NGT™ L 0.5 15-00702 Cable Kit for Float Charge L 2.0 15-00704 Vehicle Interference Suppression Kit L 1.0 15-00711 Fuse Holder with 32 A Fuse L 0.5 15-00712 Fuse, 32 A M 0.5 15-00765 GPS Receiver/Antenna for VR and SRx L 0.67 15-00766 NGTTM (VR and SRx) Desk Console 1/2B 1.5 15-00771 GPS Receiver/Antenna for ASR L 0.64 15-02063-CD NGTTM Transceiver System Technical Service Manual on CDROM (English) M 0.25 15-04102-## Reference Manual, Remote Control NGTTM Systems L 0.5 15-04104-## User Guide, HF Data Modem 3012 L 0.5 15-04104-CD User Guide, HF Data Modem 3012 (English) M 0.25 15-04125-EN Reference Manual, Split-site Remote Control NGTTM Systems (English) L 0.5 15-04127-## Getting Started Guide, NGT™ Transceiver, includes Reference Manual on CDROM L 0.5 15-04164-EN NSP Software CD Package M 0.25 15-04131-## Reference Manual, High Power Amplifiers 3061/3062 L 0.5 15-04136-## Getting Started Guide, 2110 series Manpack Transceiver, includes Reference Manual on CDROM M 0.5 15-04137-EN Getting Started Guide, NGT™ ASR Transceiver, includes Reference Manual on CDROM (English) L 0.5 15-04140-## Getting Started Guide, NGT™ SRx Transceiver, includes Reference Manual on CDROM L 0.5 15-04142-## Installation Handbook, Automatic Tuning Whip Antenna 9350 L 0.5 15-04146-CD User Guide, HF Data Modem 3212 on CDROM P4 0.3 15-04146-EN User Guide, 3212 HF Data Modem (English) P4 0.3 ## denotes language version, see page 165, Language Support Page 180 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 15-04148-CD User Guide, CrosspatchTM 3031 on CDROM (English) M 0.25 15-04148-EN User Guide, CrosspatchTM 3031 (English) L 0.5 15-04155-EN Codan HF ExpressTM and STANAG 5066 Stack (English) P1 0.14 15-04177-## EnvoyTM Transceiver Getting Started Guide, includes Reference Manual on CDROM L 0.5 15-04178-CD TPS-3250 EnvoyTM Programming Software CD M 0.25 15-10469 Opt Fan (Retro Fit) 1/2B 0.5 15-10471 NGT™ (SR and ASR) Desk Console (Retro Fit) 1/2B 1.0 15-10507 Opt Voice Encryptor (Retro Fit) 1/2B 0.5 15-10509 Opt 2 W, 2-wire (Retro Fit) 1/2B 0.5 15-10510 Opt 4 W, 4-wire (Retro Fit) 1/2B 0.5 15-60012 3040 Automatic Whip Antenna Installation Handbook, c/w Antenna Connector Sealing Kit P4 0.2 15-60024 Desk Console Hand-held Microphone, Envoy™ M 0.22 15-60025 Desk Console Boom Microphone, Envoy™ L 0.1 15-60026 Desk Console Headset, Envoy™ PSU 1.17 15-60027 Desk Console PTT footswitch, Envoy™ M 0.26 15-60028 Desk Console Headphones, Envoy™ PSU 1.16 30-35002-006 19" 1RU Vent Panel 406A 1.0 30-35002-019 19" 4RU Vent Panel 406A 2.0 30-35002-020 Fixed Equipment Rail, 457 mm Long 406A 0.5 30-37601-002 Copper Earth Strip M 0.5 30-38000-002 Shackle L 0.1 39-79150-080 Ferrite Bead Clamp P1 0.13 60-00063-501 6-way Modular Wall Mounting Socket L 0.1 60-00098-590 Adaptor, 9-pin D PIug to 25-pin D Socket P1 0.13 60-11163-204 Plug, UHF (RG213) W/proof P1 0.1 60-11163-221 Plug, UHF (RG58) W/proof P1 0.1 65-72000-012 Battery, Lead acid 12 V 90Ah (supplied dry charged) – 18.0 65-72003 Battery, 12 V 100Ah Gelcell – 39.0 ## denotes language version, see page 165, Language Support Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 181 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 65-72004 Battery, 12 V 185Ah Gelcell – 65.0 67-90200 Cable, 2C IEC C7 AUS, 2 m L 0.5 67-90201 Cable, 2C IEC C7 UK, 2 m L 0.5 67-90202 Cable, 2C IEC C7 US, 2 m L 0.5 67-90203 Cable, 2C IEC C7 EU, 2 m L 0.5 67-90305 Cable, 3C Blk Mld IEC AUS, 2 m L 0.5 67-90306 Cable, 3C Blk Mld IEC UK, 2 m L 0.5 67-90307 Cable, 3C Blk Mld IEC US, 2 m L 0.5 67-90308 Cable, 3C Blk Mld IEC EU, 2 m L 0.5 67-90309 Cable, 3C Blk Mld IEC 320-UK, 2 m L 0.5 67-90406 Cable, USB Adaptor for Memory Stick Programming 67-90800 Cable, Ethernet Crossover CAT-5E, 2 m Red L 0.38 67-90801 Cable, Ethernet Crossover CAT-5E, 10 m Red L 0.64 67-90802 Ethernet Straight CAT-5E Cable, 2 m Blue L 0.38 67-90803 Ethernet Straight CAT-5E Cable, 10 m Blue L 0.64 67-90805 Cable, Ethernet Straight CAT-5E, 100 m Blue B 2.71 78-01012 Ant, Semi-delta (2–30 MHz, 125 W PEP) T 6.0 78-01022 Ant, Full Delta (2–30 MHz, 125 W) 1022 30.0 78-01031 Adaptor, USB to DB-9, Serial M 0.5 78-02007 Battery Charger AC-DC 3121 M 0.5 78-02008 Battery Charger DC-DC 3122 M 0.5 78-02012 Battery Charger AC-DC 3123 M 0.5 78-07003-010 InterNav-CHFTM GPS Tracking Software–10 User 1/2B 1.0 78-07003-025 InterNav-CHFTM GPS Tracking Software–25 User 1/2B 1.0 78-07003-050 InterNav-CHFTM GPS Tracking Software–50 User 1/2B 1.0 78-07003-100 InterNav-CHFTM GPS Tracking Software–100 User 1/2B 1.0 78-07003-990 InterNav-CHFTM GPS Tracking Software–1 User (Dealer) 1/2B 1.0 78-08000 Handset H-250/U L 0.7 78-13016 Modem, Leased Line 1/2B 1.0 78-13035 Mast, Man-portable 6 m Tactical T 6 78-14010 3040/3042 NVIS Antenna Kit TUBE 2.6 Page 182 0.01 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Shipping Weights SHIPPING WEIGHTS Shipping Weights PART NO. DESCRIPTION BOX TYPE PACKED WGHT (kg) 78-16019 Power Supply Unit, 90 to 264 V AC L 0.2 78-16042 Sealevel PCI Synchronous Serial Card L 0.39 78-18058 Riser, fibreglass TUBE 2.0 78-23007-003 9350 Fibreglass Whip, 1.6 m NV 0.5 78-23025 9350 Tapered Stainless Steel Whip, 1.2 m NV 0.2 78-23056 9350 Tapered Stainless Steel Whip, 1.65 m NV 0.2 78-23085 3040 Fibreglass Whip, 1.6 m TUBE 1.5 78-23086 3040 Stainless Steel Whip TUBE 1.5 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 183 Standard Packing Dimensions NOTE 1: All weights shown are net packed weights calculated to the nearest 0.5 kg. NOTE 2: In a number of instances accessories will be packed together or with the main equipment resulting in a reduction of the total published weight. NOTE 3: Where applicable, the standard pack reference code has been given as a general guide to the overall dimensions of the carton/crate used to pack main equipment and some selected accessories. It should be noted, however, that the dimensions shown might vary from time-to-time depending on the consignment circumstances. Standard Packing Dimensions STANDARD PACKING DIMENSIONS REF CODE APPROXIMATE VOLUME (m3) A 510 x 510 x 280 mm 0.07 AA 510 x 510 x 280 mm 0.07 B 510 x 340 x 280 mm 0.05 B1 510 x 340 x 280 mm 0.05 B2 510 x 340 x 280 mm 0.04 BPK 590 x 410 x 200 mm 0.05 C 2200 x 130 x 90 mm 0.03 CMR 660 x 330 x 330 mm 0.07 D 1700 x 200 x 180 mm 0.06 E 1940 x 480 x 190 mm 0.18 F 600 x 600 x 350 mm 0.13 H 790 x 710 x 1670 mm 0.94 HPPA1 680 x 640 x 420 mm 0.18 HPPA2 680 x 640 x 420 mm 0.18 L 300 x 200 x 100 mm 0.01 M 230 x 210 x 105 mm 0.01 M1 3150 x 160 x 160 mm 0.08 M2 930 x 230 x 200 mm 0.04 M3 3150 x 160 x 160 mm 0.08 M4 930 x 230 x 200 mm 0.04 N 780 x 530 x 80 mm 0.03 NV 2200 x 125 x 90 mm 0.02 O 1200 x 530 x 80 mm 0.05 P1 150 x 220 x 0 mm 0.0 P4 240 x 370 x 0 mm 0.0 400 x 300 x 190 mm 0.02 PSU Page 184 DIMENSIONS Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Standard Packing Dimensions STANDARD PACKING DIMENSIONS CONT. REF CODE DIMENSIONS APPROXIMATE VOLUME (m3) R 600 x 600 x 550 mm 0.20 S 170 x 170 x 70 mm 0.01 SD1 1750 x 6.0 x 6.0 mm 0.0 SD2 770 x 360 x 100 mm 0.02 SOLA 1000 x 550 x 200 mm 0.11 SYST 1040 x 520 x 300 mm 0.16 SYS1 1030 x 520 x 300 mm 0.16 SYS2 1030 x 520 x 300 mm 0.16 SYS3 1030 x 520 x 300 mm 0.16 T 800 x 300 x 250 mm 0.06 TW 600 x 550 x 400 mm 0.13 019A 1900 x 460 x 185 mm 0.16 023A 1260 x 830 x 440 mm 0.46 023B 1100 x 1110 x 390 mm 0.48 023C 4500 x 1570 x 140 mm 0.99 024A 960 x 630 x 270 mm 0.16 024B 1100 x 1110 x 390 mm 0.48 024C 4500 x 1570 x 140 mm 0.99 1/2B 311 x 231 x 243 mm 0.02 1/2C 950 x 130 x 90 mm 0.01 40W 660 x 360 x 620 mm 0.15 406 2270 x 120 x 120 mm 0.03 406A 602 x 230 x 50 mm 0.006 408L1 660 x 410 x 160 mm 0.04 408L2 1960 x 180 x 180 0.06 420/14 5200 x 260 x 260 mm 0.35 420/23 7800 x 260 x 260 mm 0.52 533A 1200 x 530 x 300 mm 0.19 1021 1260 x 830 x 470 mm 0.49 1022 910 x 285 x 205 mm 0.05 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 185 Standard Terms & Conditions of Supply Standard Terms & Conditions of Supply “Codan’s Standard Terms and Conditions and International Product Warranty (as updated from time to time) apply to all Orders for the supply of Products by Codan to the Purchaser.” Dictionary In the Standard Terms and Conditions of Supply, the words below have the following meanings: $ means AUD, unless specifically otherwise specified; ACDC means the Australian Commercial Dispute Centre Limited A.C.N. 003 042 840 of Level 6, 50 Park Street, Sydney, NSW, 2000, Australia; Agreement means the contract between Codan and The Purchaser as described in clauses 1.4 and 1.5; Anything of Value includes cash or cash equivalents, gifts, services, employment offers, loans, travel expenses, entertainment, political contributions, charitable donations, subsidies, per diem payments, sponsorships, honoraria or provision of any other asset, even if nominal in value. AUD means Australian dollars; Business Day means any day except a Saturday, Sunday or public holiday in South Australia; Calendar Day means a calendar day with periods expressed in Calendar Days subject to extension if necessary to allow for public holidays in South Australia and/or the location where the Product (if imported) is sourced as the case may be; Catalogue means any and all catalogues of Codan products published and distributed by Codan in hard copy and electronically (including by making available for viewing through its official website) to its actual and prospective customers, setting out product details and current prices, as updated and replaced by Codan from time to time in its discretion; Codan or Company means Codan Limited A.C.N. 007 590 605 of 81 Graves Street, Newton, South Australia, 5074, Australia; Confidential Information means all information disclosed by Codan or The Purchaser and includes: (a) the fact that the parties will have, or are having, discussions, and the substance of those discussions; (b) financial information and other trade secrets and confidential know-how; (c) information regarding each party’s business; and (d) all information generated by the parties which is based on the information referred to in these paragraphs (a) to (c) inclusive, but excludes information that: (e) the parties create or develop (whether alone or jointly with any person) independently of the Confidential Information; (f) is public knowledge (otherwise than as a result of a breach of confidentiality by either party or any person to whom it has disclosed the information); (g) is rightfully known to, or in the possession or control of either party or any of its personnel and not subject to an obligation of confidentiality in accordance with the terms of this Agreement; or (h) becomes available to either party from a source other than the parties and which source has the right to use and disclose and is not bound by any obligation of confidentiality in respect of the same; Credit Limit means the AUD value of any credit facility extended by Codan to The Purchaser; Duties means any stamp, transaction or registration duty or similar charge imposed by any Government Agency and includes, but is not limited to, any interest, fine, penalty, charge or other amount imposed but excludes any income tax; EUR or € means the euro (the official currency of the Eurozone); Existing Arrangements means any arrangements and agreements between Codan and The Purchaser in effect as at the date an Order is submitted, as agreed by Codan in writing; Facilitating Payment means a payment to an individual to secure or expedite the performance of a routine government action by Government Officials; Force Majeure Event means anything outside a party’s reasonable control including, without limitation, shortages of materials, fire, storm, flood, earthquake, explosion, accident, enemy acts, war, rebellion, insurrection, sabotage, epidemic, quarantine restriction, labour dispute, labour shortage, transportation embargo or failure or delay in transportation; Government Agency means any government or governmental, semi governmental, administrative, fiscal or judicial body, department, commission, authority, tribunal, agency or entity; Page 186 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Standard Terms & Conditions of Supply Government Official means: (a) any officer or employee of a government or any department, agency or instrument of a government (including but not limited to any Government Agency); (b) any person acting in an official capacity for or on behalf of a government or any department, agency, or instrument of a government (including but not limited to any Government Agency); (c) any officer or employee of a company or business owned in whole or part by a government; (d) any officer or employee of a public international organisation such as the World Health Organisation or United Nations; (e) any officer or employee of a political party or any person acting in an official capacity on behalf of a political party; and/or (f) any candidate for political office; GST has the meaning it does in section 195-1 of the GST Act; GST Act means A New Tax System (Goods and Services Tax) Act 1999 (Cth), as amended, varied or replaced from time to time; Insolvency Event, in relation to The Purchaser, means any of the following events: (a) The Purchaser is unable to pay its creditors (or any class of them) in the ordinary course of business; (b) a receiver, receiver and manager, administrator, liquidator or similar officer is appointed to The Purchaser or any of its assets; (c) The Purchaser enters into, or resolves to enter into, a scheme of arrangement, compromise or composition with any class of creditors; (d) a resolution is passed or an application to a court is taken for the winding up, dissolution, official management or administration of The Purchaser; or (e) anything having a substantially similar effect to any of the events specified above happens under the law of any applicable jurisdiction; Intellectual Property Rights means any and all intellectual and industrial property rights anywhere in the world, including but not limited to the rights comprised in any patent, copyright, design, trade mark, eligible layout or similar right whether at common law or conferred by statute, rights to apply for registration under a statute in respect of those or like rights and rights to protect trade secrets and know how, throughout the world for the full period of the rights and all renewals and extensions; International Product Warranty means the warranty set out in the document on page 195, which is incorporated into and forms part of these Standard Terms and Conditions; Order means an order for Products created as the result of The Purchaser’s issue of a formal purchase order to Codan in hard copy or electronically (in a form agreed by Codan). Issuance of an Order (whether or not a Quotation is first issued by Codan) is deemed to constitute acceptance of these Standard Terms and Conditions by The Purchaser. In the event that a Quotation is issued by Codan, issuance of an Order is also deemed to constitute acceptance of the Quotation by The Purchaser; Order Acknowledgement means Codan's written confirmation that an Order has been received from The Purchaser, and the Agreement brought into existence; Order Value means the total price charged by Codan to The Purchaser for any Order, and including any amounts payable by The Purchaser and charged by Codan in accordance with clause 3.1; Payment refers to and includes any direct or indirect offer to pay, promise to pay, authorisation of payment of, or transfer of, Anything of Value; Perfected has the meaning given to that term in the PPSA; PPSA means the Personal Properties Securities Act 2009 (Cth) and any regulations made under it; PPS Register means the register established under the PPSA; Products means the products to be manufactured and/or imported by Codan for The Purchaser as listed in the Order; Quotation or Quote means the quote, if any, issued by Codan to The Purchaser in respect of the Products to which these Standard Terms and Conditions of Supply are attached; Security Agreement has the meaning given to that term in the PPSA; Security Interest has the meaning given to that term in the PPSA; Supply has the same meaning it does in section 9-10 of the GST Act and excludes any “GST-free supplies” and “input taxed supplies” as those terms are defined in section 195-1 of the GST Act; Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 187 Standard Terms & Conditions of Supply Tax or Taxes means any tax, levy, charge, impost, fee, deduction, compulsory loan or withholding (including corporate tax, personal income tax, fringe benefits tax, payroll tax, withholding tax, excise and import duties, GST, consumption tax, value added tax or any other taxes, levies or charges), which is assessed, levied, imposed or collected by any Government Agency, and includes any interest, fine, penalty, charge, fee or any other amount imposed on or in respect of any such amounts; The Purchaser means the entity requesting that Products be supplied and sold to it by Codan by the issuance of an Order, as listed in the Quotation (if applicable); and USD means US dollars. 1. Catalogue/Credit Offers, Quotations and Agreement 1.1 The Purchaser acknowledges and agrees: (a) that the Catalogue and/or approval of a Credit Limit by Codan following a request for a credit facility received from The Purchaser in the form specified by Codan constitutes an offer by Codan to sell the Products to The Purchaser on the terms and conditions set out in these Standard Terms and Conditions of Supply, at the standard prices for the Products set by Codan which are current on the date The Purchaser submits an Order to Codan, as notified by Codan to The Purchaser (subject always to clause 2.1 below) (Catalogue/Credit Offer); and (b) that the Catalogue/Credit Offer may be accepted by The Purchaser at any time by submitting an Order with Codan. 1.2 By submitting an Order in response to a Catalogue/Credit Offer, The Purchaser warrants and represents to Codan that: (a) it has been provided with a copy of Codan's current Product Price list and that it has reviewed this list prior to submitting the Order; and (b) it has read and understood these Standard Terms and Conditions of Supply prior to submitting the Order, and agrees to be bound by them in full. 1.3 In addition to the Catalogue/Credit Offer, Codan may, in its discretion and following a request by The Purchaser, make an offer to The Purchaser for the sale of Products by issuing a Quotation. Unless otherwise specified in the Quotation issued by Codan to The Purchaser (if any) or agreed to in writing by Codan, all Quotations issued by Codan are valid for 30 days from the date of issue (Acceptance Period). The Purchaser must accept a Quotation by submitting an Order with Codan during the Acceptance Period. Any Quotation not accepted by The Purchaser during the Acceptance Period will lapse. 1.4 A contract between Codan and The Purchaser for the supply by Codan, and the purchase by The Purchaser, of the Products will come into existence: (a) in cases where a Quotation is issued by Codan, on the date The Purchaser accepts the Quotation by submitting a valid Order with Codan within the Acceptance Period; and (b) in all other cases, on the date that The Purchaser submits a valid Order with Codan, in response to the Catalogue/Credit Offer. 1.5 1.6 Codan will determine in its sole discretion whether an Order Form has been validly completed and submitted by The Purchaser. The contract will comprise: (a) these Standard Terms and Conditions of Supply; (b) the Quotation issued by Codan, if any; (c) the Product details listed in the Order; and (d) the invoice issued by Codan to The Purchaser, to the exclusion of any other terms and conditions (including but not limited to any variations to either these Standard Terms and Conditions or the terms of the Quotation or the Catalogue/Credit Offer (as applicable) purported to be made by The Purchaser in the Order) and apart from any terms, conditions or guarantees implied or provided for by applicable law which cannot lawfully be excluded. Codan may (but is not obliged to) issue an Order Acknowledgement to The Purchaser, confirming the terms of the contract. Page 188 1.7 In the event of an inconsistency between any of the documents listed in clause 1.5 above, the terms of these Standard Terms and Conditions will prevail to the extent of the inconsistency, with the terms of the Quotation (if any) prevailing thereafter. To the extent of any inconsistency between the document in clause 1.6(c) and 1.6(d) above, the document described in clause 1.6(d) will prevail. 1.8 Neither this Agreement nor any Order that has been submitted can be cancelled by The Purchaser except with the prior written consent of Codan. Codan can cancel and terminate any Order or this Agreement in its sole discretion, without penalty, if it considers that an Order Form has not been validly completed and/or submitted by The Purchaser. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Standard Terms & Conditions of Supply 2. Prices 2.1 Prices specified by Codan for the Products in a Quotation or any current Product Price list issued by Codan, as applicable, are based upon the prevailing currency exchange rates generated by the Codan system. Subject to Codan deciding in its sole discretion that it would be fair and reasonable in the circumstances to do so, Codan may pass on any variation in currency exchange rates to The Purchaser in any invoice issued in accordance with clause 3.2. 2.2 If a Quotation has been issued by Codan, The Purchaser acknowledges that it has been prepared by Codan on the basis of, and in reliance upon, the information provided by The Purchaser, and further acknowledges that the provision of incomplete or misleading information by The Purchaser, unforeseen circumstances, misinterpretations, variations and similar events may result in charges additional to those set out in the Quotation being payable by The Purchaser for the Products. The Purchaser agrees to pay any such additional amounts to Codan, in full. 2.3 Unless otherwise expressly specified by Codan, all prices stated are exclusive of Product delivery costs and freight charges. 3. Payment 3.1 The Purchaser is solely responsible for payment of all freight, insurance, delivery costs, Taxes and other charges levied or payable in respect of the Products, unless otherwise agreed by the parties in writing. 3.2 Codan will invoice The Purchaser for the Order Value of the Order at any time following receipt of such Order. 3.3 Unless otherwise stated in the Quotation the due date for payment by The Purchaser to Codan for the Order (Due Date) is as follows: (a) 30 days from the date on which the invoice was issued, if the following conditions are satisfied at the time that the Order was submitted to Codan (i) The Purchaser has a pre-approved credit facility with Codan and (ii) the Order Value, combined with any outstanding payments due to Codan by The Purchaser at the time of the Order, fall within The Purchaser’s approved Credit Limit; and (b) in all other cases, payment is immediately due at the time that The Purchaser places the Order with Codan. 3.4 If The Purchaser fails to make any payment by the Due Date, then, without prejudice to any other right or remedy available to Codan, Codan may, in its sole discretion elect to: (a) suspend any further deliveries to The Purchaser arising from the Order; (b) cancel the Order for Products not yet supplied to The Purchaser in whole or in part by Codan; (c) enter the property of The Purchaser in order to repossess the Products; (d) appoint a receiver or receiver and manager to do anything the law allows a receiver or receiver and manager to do; (e) charge The Purchaser interest (both before and after any judgement) on the unpaid amount at the rate of 10% per annum until payment is made in full; and/or (f) withdraw any Credit Limits or credit facilities previously approved and extended to The Purchaser. 4. Delivery 4.1 Unless otherwise stated in any Order Acknowledgement issued by Codan to The Purchaser, Codan will deliver the Products to The Purchaser in the manner (i) specified in the Order or (ii) if a Quotation has been issued, in the manner specified in the Quotation, regardless of what is stated in the Order submitted by The Purchaser. 4.2 Codan will use its reasonable endeavours to deliver the Products described in the Order on the delivery date requested by The Purchaser. 4.3 Risk of damage to or destruction or loss of the Products will pass to The Purchaser at the time of delivery to The Purchaser or its nominated carrier, as appropriate. 4.4 Notwithstanding delivery and the passing of risk in the Products, the parties acknowledge and agree that the title to, and property and ownership of, the Products supplied under this Agreement will not pass to The Purchaser until Codan has received, in cleared funds, payment in full for the Products and any other sums which are or may become due to Codan under this Agreement or any other agreement or arrangement between the parties. 4.5 Until such time as full title, property and ownership of the Products passes to The Purchaser in accordance with clause 4.4, and while the Products remain in The Purchaser’s full control and possession: (a) The Purchaser must hold the Products as Codan’s fiduciary agent and bailee; (b) The Purchaser must keep the Products properly stored, protected and insured; (c) Codan may at any time after payment is overdue require The Purchaser to deliver up the Products to Codan and, if The Purchaser fails to deliver up the Products immediately, Codan may enter the premises of The Purchaser or any third party where the Products are stored and repossess them; and (d) The Purchaser must not pledge or in any way charge by way of security for any indebtedness, any of the Products which remain the property of Codan. If The Purchaser does pledge or in any way charge by way of security for any indebtedness any of the Products for which property and ownership has not passed to The Purchaser, all moneys owing by The Purchaser to Codan will (without prejudice to any other right or remedy of Codan) immediately become due and payable to Codan. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 189 Standard Terms & Conditions of Supply 5. PPSA 5.1 The Purchaser acknowledges that until such time as full title, property and ownership of the Products passes to The Purchaser under clause 4.4, this Agreement constitutes a Security Agreement for the purposes of the PPSA, and Codan has a Security Interest in the Products. 5.2 Without limiting clause 17.6, The Purchaser agrees to do such things as Codan may require from time to time to ensure that any Security Interest of Codan arising from or connected with this Agreement is Perfected under the PPSA for whatever period Codan determines in its sole discretion, including signing documents and providing Codan with all further information required to enable Codan to register its Security Interests on the PPS Register, and to otherwise protect Codan's position under the PPSA. The Purchaser must keep Codan fully informed of all relevant information regarding it and its activities, including by providing not less than 14 days notice in writing of any proposed change in its name or contact details, and immediately advising Codan of material changes in its business activities. 5.3 The Purchaser agrees to indemnify Codan for all expenses incurred by Codan in registering its Security Interests on the PPS Register, and will reimburse Codan for all such expenses immediately upon demand. 5.4 The Purchaser waives its rights under section 157 of the PPSA to receive a notice in relation to the registration events to which section 157(3)(a) of the PPSA applies, including without limitation, the right to receive a copy of a verification statement confirming registration of a financing statement or financing change statement relating to the Security Interest created by this Agreement. 5.5 The Purchaser agrees that nothing in sections 118, 121(4), 125, 130, 142 or 143 of the PPSA will apply to this Agreement or any Security Interest in the Products created by this Agreement, and waives its rights to receive any of the following documents: (a) a notice of removal of an accession under section 95 of the PPSA; (b) a notice of an intention to seize collateral under section 123 of the PPSA; (c) a notice of a disposal of collateral under section 130 of the PPSA; (d) a statement of account under section 132(3)(d) of the PPSA; (e) a statement of account under section 132(4) of the PPSA; (f) a notice of retention of collateral under section 135 of the PPSA; and (g) any notice from Codan under each of the provisions listed in section 144 of the PPSA. 6. The Purchaser's Obligations 6.1 Codan and The Purchaser agree that The Purchaser: (a) is solely responsible for consideration and validation of Product designs and Product functionality, to confirm suitability for particular applications, as desired by The Purchaser; (b) must advise Codan of all statutory, regulatory and other official standards and/or requirements which the Product must comply with, at the time of submitting the Order to Codan and immediately upon becoming aware of these at any other time; and (c) must provide Codan with any other information which Codan may request in respect of the intended application/use of the Products. 7. Warranty 7.1 7.2 Codan agrees to provide the International Product Warranty in respect of the Products. The International Product Warranty will not apply in the event of termination of this Agreement by Codan pursuant to clauses 12.4, 13.4 or 15.3. 8. Exclusion and Limitations of Liability 8.1 The Purchaser acknowledges and agrees that notwithstanding clause 4.2, any delivery dates quoted by Codan for delivery of the Products are approximate only, and will not be binding upon Codan. 8.2 Codan does not exclude or limit the application of any provision of any applicable statute, legislation or other regulation (including the Competition and Consumer Act 2010 (Cth) and its Schedules and Regulations) where to do so would contravene that statute, legislation or regulation or cause any part of this clause to be void and nothing in this Agreement is to be interpreted as doing so. 8.3 Subject always to clause 8.2, to the extent permitted by law Codan excludes from this Agreement: (a) all conditions, warranties, guarantees and terms implied by statute, general law, international convention or custom, except any implied term, condition, guarantee or warranty the exclusion of which would contravene any statute or cause this clause to be void (Non-excludable Condition); (b) all liability to The Purchaser for consequential or indirect damages arising out of or in connection with this Agreement even if Codan knew they were possible, or they were otherwise reasonably foreseeable, and including without limitation, loss of profits and damage suffered as a result of claims by any third person, such as a customer of The Purchaser; and (c) all liability to The Purchaser in negligence for acts or omissions of Codan, its employees, agents and contractors arising out of or in connection with this Agreement. Page 190 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Standard Terms & Conditions of Supply 8.4 To the extent permitted by law, Codan will not be responsible for any consequences of any modification to the Products (whether or not authorised) or for any loss, damage or claim arising from such actions. The Purchaser agrees to indemnify, defend and hold harmless Codan against any and all claims, demands, suits, causes of action, damages and legal fees (on a solicitor-own client basis) or expenses or costs whatsoever arising, directly or indirectly, from any modification of the Products, and unconditionally frees, releases and discharges Codan and its officers, agents, contractors and employees from any claim or cause of action arising in connection with such matters, to the fullest extent permitted by applicable law. 8.5 To the extent permitted by law, Codan will not be liable or otherwise responsible for any loss, accident, damage or injury arising in connection with The Products, or any failure of the Products to operate in the manner required by The Purchaser, whether or not caused by a defect or fault in the Products or due to Codan's negligence. The Purchaser unconditionally frees, releases and discharges Codan and its officers, agents, contractors and employees from any claim or cause of action arising in connection with the use of the Products by The Purchaser, to the fullest extent of the law. 8.6 To the extent permitted by law, Codan’s liability to The Purchaser for breach of any Non-excludable Condition which is applicable (and other than one implied by sections 51, 52 or 53 of Schedule 2 of the Competition and Consumer Act 2010 (Cth) is limited to any one of, at Codan’s option, repairing or replacing the Products in respect of which the breach occurred, supplying equivalent products, payment of the cost of replacing the Products or acquiring equivalent products, or payment of the cost of having the Products repaired. 8.7 Notwithstanding anything to the contrary in this Agreement, and to the extent permitted by law, Codan’s maximum liability to The Purchaser for any cause of action or claim in connection with the Products or this Agreement shall be limited to a total aggregate amount equal to the Order Value of the Order in connection with which the cause of action or claim arose. 9. Intellectual Property 9.1 The Purchaser expressly acknowledges and agrees that Codan is the sole proprietor and owner of all existing and future Intellectual Property Rights associated with the Products (including all modifications and improvements), and that this Agreement does not grant or transfer to it any rights to the Intellectual Property Rights associated with the Products. 9.2 The Purchaser must not copy, reverse engineer, improve, enhance, develop, refine, modify or otherwise alter any aspect of the Products or any Intellectual Property Rights associated with the Products, or permit or assist a third party to undertake any of these actions. 9.3 Notwithstanding anything to the contrary in this Agreement, The Purchaser acknowledges and agrees that Codan will own all rights in any improvements, enhancements developments, modifications or refinements to the Products or associated Intellectual Property Rights developed or created by The Purchaser, and The Purchaser will have no claim to such materials. The Purchaser agrees that it will execute, procure and deliver to Codan all assignments required to give effect to this clause 9.3, and hereby waives any and all rights to any such improvements, developments, enhancements modifications or refinements. 10. Confidentiality 10.1 Each party: (a) may use Confidential Information of the other party solely for the purposes of this Agreement; (b) must keep confidential all Confidential Information of the other party; and (c) may disclose Confidential Information of the other party only to (i) employees and contractors who (A) are aware and agree that the Confidential Information of the other party must be kept confidential and (B) either have a need to know (and only to the extent that each has a need to know), or have been specifically approved by the other party, or (ii) as required by law or stock exchange regulation. 10.2 Each party must notify the other party immediately once it becomes aware of any breach of confidentiality and must take all reasonable steps necessary to prevent further unauthorised use or disclosure of the Confidential Information. 11. Taxes and Government Charges 11.1 The amounts payable by The Purchaser to Codan for, or in connection with this Agreement do not include any amounts on account of Taxes and Duties. The Purchaser shall be solely liable for and shall pay, when due and payable, all Taxes and Duties which may be imposed in relation to the Products, or which is assessed or chargeable in respect of this Agreement and any associated documents or transactions. 11.2 The Purchaser agrees to indemnify Codan in respect of any liability for Taxes and Duties, and shall pay any Taxes and Duties notified to it by Codan immediately upon request. The Purchaser must provide Codan with all necessary tax invoices, receipts and other documentation as required by Codan in accordance with applicable laws, legislation and regulations. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 191 Standard Terms & Conditions of Supply 11.3 In the case of GST payable in Australia, if applicable, The Purchaser must pay to Codan an additional amount on account of GST equal to the amounts payable by The Purchaser for the Supply multiplied by the prevailing GST rate. Notwithstanding anything to the contrary in this clause, The Purchaser is not required to pay any additional GST amount until such time as The Purchaser has been provided with a tax invoice by Codan, which is in an approved form for GST purposes. 11.4 The additional amounts due to Codan on account of Taxes and Duties are payable at the same time and in the same manner as the price and any other amounts payable by The Purchaser are required to be paid to Codan under this Agreement. 12. Government Approvals 12.1 Codan agrees, at its cost, to use its reasonable endeavours to obtain all necessary export licences, clearances and other consents and approvals from Government Agencies which are necessary for the sale and supply/export of the Products to The Purchaser. The Purchaser agrees to complete and provide to Codan any documentation required by Codan to obtain any required approvals and consents. 12.2 The parties agree that Codan's obligations under this Agreement are conditional upon Codan being issued all necessary export licences, clearances and other consents and approvals by the relevant Government Agencies. In the event that Codan is unable to secure all necessary licences, clearances, permits, approvals and other necessary consents from appropriate Government Agencies, Codan shall be entitled to immediately terminate this Agreement by written notice, and Codan shall not be required to supply the Products to The Purchaser. In no circumstances shall Codan be liable to The Purchaser or any other person for any loss or damage (including without limitation indirect or consequential loss or loss of profits) arising in connection with Codan's failure to obtain any necessary documentation from Government Agencies required for the sale and supply/export of the Products to The Purchaser, or the termination of this Agreement pursuant to this clause 12.2, and The Purchaser unconditionally frees, releases and discharges Codan and its officers, agents, contractors and employees from any claim or cause of action arising in connection with Codan's failure to obtain any export licence, clearances and other necessary consents and approvals from appropriate Government Agencies. 12.3 The Purchaser is solely responsible, at its sole cost and expense, for ensuring that the Products meet the requirements of any country into which they are imported, and must obtain and maintain any necessary import licences and permits, and all other clearances and consents from Government Agencies required for the acquisition and use of the Products by The Purchaser (including but not limited to customs approvals and clearances). Codan shall supply The Purchaser with any documents reasonably requested by The Purchaser for the purposes of complying with its obligations under this clause 12.3. 12.4 Codan may at any time require that The Purchaser supply it with copies of licences, permits, clearances and approvals issued by Government Agencies and obtained by The Purchaser as required by clause 12.3, and The Purchaser agrees to immediately comply with any such request. If at any time Codan becomes aware that The Purchaser has failed to comply with its obligations under clause 12.3, it may immediately terminate this Agreement by written notice, and all outstanding amounts shall become immediately due and payable by The Purchaser. The Purchaser agrees to indemnify, defend and hold harmless Codan against any and all claims, demands, suits, causes of action, damages and legal fees (on a solicitor own client basis) or expenses or costs whatsoever arising, directly or indirectly, from any failure by The Purchaser to comply with its obligations under clauses 12.3 or 12.4. 13. Anti-Bribery and Corruption Requirements 13.1 It is a material term of this Agreement that The Purchaser must comply with the following: (a) The Purchaser must comply fully at all times with all applicable laws and regulations, including but not limited to applicable anti-corruption laws of the territory in which The Purchaser conducts business with Codan. (b) The Purchaser must not, and covenants that it will not, in connection with the performance of this Agreement, directly or indirectly promise, authorise, ratify, offer to make or make, or take any action, in furtherance of any Payment of Anything of Value to any individual, or to an intermediary for payment to any individual, including a Government Official, for the purpose of influencing or inducing or as a reward for any act, omission or decision to secure an improper advantage or to improperly assist The Purchaser or Codan in obtaining or retaining business. (c) The Purchaser must not, and covenants that it will not, in connection with the performance of this Agreement, directly or indirectly promise, authorise, ratify or offer to make or make any Facilitating Payment to any individual, or to an intermediary for payment to any individual, including a Government Official. (d) The Purchaser must not contact, or otherwise meet with any Government Official with respect to any transactions required under this Agreement, without the prior written approval of Codan and, when requested by Codan, only in the presence of a Codan designated representative. Page 192 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Standard Terms & Conditions of Supply (e) The Purchaser represents that it has not been convicted of or pleaded guilty to a criminal offence, involving fraud or corruption; that it is not now, to the best of its knowledge, the subject of any government investigation for such offences, and that it is not now listed by any government agency as debarred, suspended, proposed for suspension or debarment, or otherwise ineligible for government procurement programs. (f) The Purchaser represents and warrants that except as disclosed in writing: (i) it does not have any interest which directly or indirectly conflicts with its proper and ethical performance of this Agreement; and (ii) it will maintain arms length relations with all third parties (including Government Officials) with which it deals for or on behalf of Codan or in the performance of this Agreement. 13.2 The Purchaser agrees that Codan may make full disclosure of information relating to a possible violation of the terms of this clause 13 at any time and for any reason to any competent government bodies and its agencies (including Government Agencies), and to whomsoever Codan determines in good faith has a legitimate need to know. 13.3 Codan will be entitled to terminate this Agreement (without payment of compensation to The Purchaser) immediately on written notice to The Purchaser, if The Purchaser fails to perform its obligations in accordance with the terms of this clause 13. Codan will not be responsible or liable for any loss or damages whatsoever arising from or in connection with this clause 13, whether sustained by The Purchaser or any other party. 14. Insurance 14.1 The Purchaser must take out and maintain at all times, with reputable insurers, valid and enforceable insurance policies in respect of the following: (a) product and public liability insurance, for an amount not less than $10 million per incident or event; (b) all necessary statutory workers compensation insurance; and (c) such other risks that a reasonable, prudent person carrying on the business of The Purchaser would be likely to insure against. 15. Termination 15.1 Codan may terminate this Agreement with immediate effect by written notice to The Purchaser if: (a) The Purchaser is the subject of an Insolvency Event; or (b) at the time of termination, a Force Majeure Event has persisted for greater than 40 Business Days. 15.2 The Purchaser may terminate this Agreement with immediate effect by written notice to Codan if Codan breaches any material term of this Agreement, which is capable of remedy, and fails to remedy the breach within 20 Business Days after receiving a notice requiring it to do so. 15.3 Without limiting Codan's other rights under this Agreement, Codan may terminate this Agreement with immediate effect by written notice to The Purchaser if: (a) The Purchaser breaches any term of this Agreement, which is capable of remedy, and fails to remedy the breach within 20 Business Days after receiving a notice requiring it to do so; (b) The Purchaser breaches any term of this Agreement and such breach is not capable of remedy; or (c) The Purchaser repeatedly breaches any term of this Agreement and, within 20 Business Days after receiving a notice requiring it to do so, fails to satisfy Codan that a breach of that term will not recur. 15.4 Termination of this Agreement will not affect any accrued rights or remedies a party may have as at the date of termination, unless explicitly stated otherwise in this Agreement. 16. Dispute Resolution 16.1 A party will not commence arbitration or court proceedings (except proceedings seeking interlocutory relief) in respect of a dispute arising out of this Agreement (Dispute) unless it has complied with this clause. 16.2 A party claiming that a Dispute has arisen will notify the other party of the Dispute in writing. 16.3 Each party to the Dispute will ensure that during the 30 Calendar Day period after a notice is given under clause 16.2 (or a longer period agreed between the parties) the chief executive officers (or equivalents) of the parties will use their best reasonable endeavours to resolve the dispute in good faith. 16.4 If after fourteen (14) days the parties are unable to resolve the Dispute under clause 16.3, the parties will attempt to settle the dispute by mediation conducted in accordance with the Commercial Mediation Guidelines of the ACDC. 16.5 The parties shall attempt to agree on the appointment of a mediator for the purposes of mediation of the Dispute pursuant to clause 16.4, and if the parties cannot agree on the identity of a mediator within seven (7) Calendar Days, the mediator will be appointed by ACDC within seven (7) Calendar Days thereafter. Mediation will be held within seven (7) Calendar Days of the appointment of the mediator. 16.6 Each party will bear its own costs of resolving a Dispute under this clause 16, and will bear equally the costs of any mediator required to be engaged. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 193 Standard Terms & Conditions of Supply 16.7 If mediation does not proceed within the timetable set out in clauses 16.4 and 16.5, or is not successful in resolving the Dispute, the parties will be entitled to terminate the Dispute resolution process by giving notice in writing to all other parties and commence arbitration or court proceedings in respect of the Dispute. Nothing in this clause 16 prevents a party from seeking urgent interlocutory relief. 16.8 Nothing in this clause 16 prevents or limits The Purchaser from exercising its rights and requiring remedies from Codan in respect of a breach of a Non-Excludable Condition (subject always to clause 8 above). 17. Miscellaneous 17.1 Interpretation – In these Standard Terms and Conditions of Supply: (a) the singular includes the plural and vice versa; (b) the word person includes a firm, a body corporate, an unincorporated association, body or organisation established pursuant to international treaty, intergovernmental body, or government authority and other official authority; (c) a reference to a document or legislation includes a reference to that document or legislation as varied, amended, novated or replaced from time to time; (d) a reference to a person includes a reference to the person’s executors, administrators, successors, substitutes (including, but not limited to, persons taking by novation) and permitted assigns; and (e) headings are inserted for convenience and do not affect the interpretation of these Standard Terms and Conditions of Supply. 17.2 Survival – The provisions of clauses 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13, 16 and 17 of these Standard Terms and Conditions of Supply survive the expiry or termination of this Agreement. 17.3 Force Majeure – If a Force Majeure Event precludes Codan from partially or wholly complying with its obligations under this Agreement then: (a) as soon as reasonably practicable after that Force Majeure Event arises, Codan must notify The Purchaser of the Force Majeure Event, and Codan’s obligation to perform in accordance with this Agreement will be suspended for the duration of the actual delay arising directly out of the Force Majeure Event or 40 Business Days, whichever is shorter, provided that Codan does everything reasonably possible to mitigate the effects of the Force Majeure Event. (b) If a Force Majeure Event persists for greater than 40 Business Days, Codan shall be entitled to terminate this Agreement in accordance with clause 15.1(b). Page 194 17.4 Governing Law – This Agreement will be governed by and construed in accordance with the laws applicable in South Australia. The parties submit to the exclusive jurisdiction of the courts of South Australia in respect of matters arising out of or in connection with this Agreement (including Disputes). The parties agree that the United Nations Convention on Contracts for the International Sale of Goods (adopted at Vienna, Austria on 10 April 1980) (including as incorporated into South Australian law by the Sale of Goods (Vienna Convention) Act 1986 (SA)) will not apply to this Agreement. 17.5 No Assignment – The Purchaser must not assign or otherwise deal with its rights and obligations under this Agreement without the prior written approval of Codan, to be provided by Codan in its reasonable discretion. 17.6 Further Action – Each party must (a) do all acts necessary or desirable to give full effect to this Agreement, and (b) refrain from doing anything which might prevent full effect being given to this Agreement. 17.7 Variation – A variation or modification of this Agreement must be in writing and signed by an authorised representative of each party. 17.8 Severability – If any provision of this Agreement is held by any competent authority to be invalid or unenforceable in whole or in part the validity of the other provisions of this Agreement and the remainder of the provision in question will not be affected. 17.9 No Waiver – No waiver by a party of any breach of this Agreement by another party shall be considered as a waiver of any subsequent breach of the same or any other provisions. 17.10 Entire Agreement – This Agreement constitutes the entire agreement between the parties about its subject matter (without limiting clause 8.2 in any way) and subject to the remainder of this clause, supersedes all previous representations, understandings and agreements in connection with that subject matter. This Agreement overrides any terms for the sale and supply of Products tendered to Codan by The Purchaser, irrespective of whether such terms are tendered before or subsequent to the date of the Order. However, the parties agree that the Existing Arrangements continue in full force and effect, and that nothing in this document supersedes, alters or otherwise affects the Existing Arrangements. In the event of an inconsistency between the obligations of the Parties under this Agreement and any Existing Arrangements, the Existing Arrangements prevail to the extent necessary. 17.11 Relationship – The relationship between the parties is and will remain that of independent contractors, and nothing in this document constitutes the parties as partners or joint venturers or constitutes any party as the agent of another party or gives rise to any other form of fiduciary relationship between the parties. 17.12 Notices – Notices by a party must be delivered by (i) prepaid post (ii) facsimile or (iii) hand, and sent to the address of the receiving party specified in the Order. Notices shall be deemed to have been received by hand upon delivery, by post within two (2) Business Days of sending and by facsimile upon receipt of a successful transmission report. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 International Product Warranty provided by Codan International Product Warranty 1. In this document: (a) ACL means the Australian Consumer Law as set out in Schedule 2 of the Australian Competition and Consumer Act 2010 (Cth); (b) Codan means Codan Limited A.C.N. 007 590 605 of 81 Graves Street, Newton, South Australia, 5074, Australia (Ph: +61 (8) 8305 0311); (c) Codan Products means, with the exception of LMR Products, all Codan products manufactured by or on behalf of Codan; (d) LMR Products means all Land Mobile Radio products manufactured in Canada; (e) Material means a material or component used by Codan in the manufacture of Warranted Products; (f) Warranted Products means the Codan Products and the LMR Products; (g) Warranty Period means: i) for Codan products, a period of three (3) years from the date of shipment to the purchaser; and (ii) for LMR Products, a period of two (2) years from the date of shipment to the purchaser; and (h) Workmanship means the handling, assembly and manufacturing processes performed by or on behalf of Codan in order to manufacture Codan Warranted Products. 2. Codan warrants that for the duration of the Warranty Period, all Warranted Products will be free of faults arising from defects in design, Workmanship or Materials, on the terms and conditions set out in this document. 3. Should any fault due to bad design, Workmanship or Materials be proven in Warranted Products acquired by the purchaser at any time within the prescribed Warranty Period, Codan will, subject to the terms of this document as set out below, remedy such fault free of charge provided the Warranted Products are returned to Codan or to a service centre authorised by Codan. 4. All Warranted Products returned for warranty repair must be sent to 81 Graves Street, Newton, South Australia, 5074, Australia if returned to Codan, and if returned to a service centre authorised by Codan must be sent to the address for the service centre as listed on Codan's website. The purchaser is responsible for all freight, insurance, taxes, duties and any costs of returning the Warranted Products to Codan or a service centre authorised by Codan for warranty repairs. Codan is only responsible for the freight costs of returning the repaired Warranted Products to the purchaser. 5. All Warranted Products returned for warranty repair must have a valid Return Material Authorisation (RMA) number issued by Codan or a Codan authorised service centre prior to return by the purchaser. This RMA number must be clearly indicated and marked on all documentation and packaging by the purchaser when returning the Warranted Products in accordance with item 4 of this document. 6. This express warranty shall not extend to damage of Warranted Products during transit or transportation, or any abuse, accident or improper installation, connection, adjustment, repair or use of goods otherwise than in accordance with instructions issued by Codan. This express warranty does not apply to any Warranted Products in respect of which the serial number has been altered, defaced or removed. 7. This express warranty is incorporated into, and forms part of, Codan's Standard Terms and Conditions of Supply. Accordingly, it is subject to the terms of Codan's Standard Terms and Conditions of Supply, including but not limited to clauses 8.2 - 8.7. 8. Subject to the matters set out in this express warranty, and to the full extent permitted by law, no liability (whether expressed or implied) of any nature whatsoever, is accepted by Codan for any consequential loss, damage or injury arising as a result of any fault in the Warranted Products. 9. This express warranty does not extend to goods supplied by Codan which are not designed or manufactured by or on behalf of it. Some goods supplied but not manufactured by or on behalf of Codan, or Materials manufactured by third parties which are used in Warranted Products, benefit from specific warranties provided by their manufacturers. Codan will make reasonable endeavours to ensure that the purchaser receives the full benefit of any warranty given by the manufacturer in respect of goods supplied but not manufactured by or on behalf of Codan, and Materials manufactured by third parties. To the extent permitted by law, such action will be the sole remedy available to the purchaser in respect of any faulty or defective goods or Materials not manufactured by or on behalf of Codan. 10. This express warranty is valid for Warranted Products purchased from Codan anywhere in the world. Warranty service will be provided in accordance with this express warranty in any country of the world where there is a service centre authorised by Codan. 11. The benefits conferred by this express warranty are in addition to all other non-excludable rights and remedies which the purchaser may have under the ACL and any similar laws in Australia or elsewhere. 12. To the extent permitted by law, Codan’s liability for any non-excludable term, condition, guarantee or warranty applicable under the ACL or its equivalents is limited to (at Codan’s option): (a) In the case of goods – repairing, replacing or supplying equivalent goods, or paying the cost of any of those remedies to the purchaser; or (b) In the case of services – supplying the services again or paying the cost of having the services supplied again. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 195 International Product Warranty provided by Codan 13. Codan provides the following advice to all purchasers who are consumers as defined by the ACL and to whom the ACL applies, as required by the ACL: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Page 196 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 2240 Smartlink Accessory Addendum This is an Addendum to the HF Radio Communications International Product Catalogue, Issue 8, January 2015. It outlines the details of the new 2240 SmartLink™ accessory now offered with the Envoy™ Transceiver. 2240 SMARTLINK ACCESSORY PRODUCT PART NO. DESCRIPTION 2240 SmartLink Accessory The Envoy SmartLink is a rugged Ethernet switch that provides wired and wireless access points for a connected Envoy transceiver system for both mobile and base applications. Up to two SmartLinks may be connected directly to an Envoy RF Unit with no requirement for external power supply. The SmartLink supports connection of either Handset or Desk Console control point devices. SmartLinks may also be deployed into IP networks in support of remote access Envoy transceiver system applications. STANDARD FEATURES: • 2221 or 2220 Handset connection • 2230 Desk Console connection • Compatible with Envoy X1 and X2 • • • • • • • transceivers Wireless access point (antenna optional) 2 x RJ-45 Ethernet ports Status LED indicators Reset function Linking cable connection External speaker connection External power supply connection (12 V DC) NOTE: 2221 or 2220 Envoy Handsets must be of Mk2 build standard when used with the SmartLink. This is required to support output of speaker audio at the SmartLink. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 197 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-DIRECT-SINGLE PART NO. DESCRIPTION SmartLink Direct Single, 6 m This package can be used for directly connecting a SmartLink to an Envoy RF Unit using a 6 m interface cable. The package contains the parts needed for adapting a standard Envoy mobile configuration for use with the SmartLink. No external DC supply is required for the SmartLink in this configuration. Typical use case scenarios include mobile Envoy installations where WiFi or Ethernet cable access to embedded Envoy data modems is required. This configuration presents the added advantage of keeping the RF Unit 15-way and 6-way interfaces free for connection of other accessories. COMPRISING: 08-07336-001 78-01263 08-07205-006 08-04515-001 15-04186-EN • • • • • 2240 Envoy SmartLink WiFi Antenna, direct connect Cable, Envoy SmartLink to RF Unit, 6 m Earth Wire, 0.5 m 2240 Reference Manual SMARTLINK-DIRECT-SINGLE package parts shown in an Envoy mobile system * *Computer and computer WiFi shown only for illustration. Computer is not supplied by Codan. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 198 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-DIRECT-DUAL-6M PART NO. DESCRIPTION SmartLink Direct Dual, 6 m This package can be used for connecting two SmartLinks to an Envoy RF Unit using a 6 m interface cable and 6 m linking cable. Note that this package assumes use of 2221/2220 Handset control points. If a 2230 Desk Console is required at either Smartlink, the 08-07338-001 interface cable may be required. The package contains the parts needed for adapting a standard Envoy mobile configuration to a dual SmartLink, dual Control Point (Handset) configuration. No external DC supply is required for the SmartLink in this configuration. Typical use case scenarios include mobile Envoy installations where dual Envoy control points are required. WiFi or Ethernet cable access to embedded Envoy data modems, via the SmartLink, is also supported, however it is recommended that WiFi is enabled at only one SmartLink when two SmartLinks are in close proximity. COMPRISING: 08-07336-001 78-01263 08-07337-006 08-07205-006 15-00649 08-07000-001 15-00149 08-04515-001 15-04186-EN • • • • • • • • • 2240 Envoy SmartLink (x2) WiFi Antenna, direct connect Cable, Envoy SmartLink Linking, 6 m Cable, Envoy SmartLink to RF Unit, 6 m External Speaker, 4 m lead Envoy 2220 Handset Envoy Handset cradle kit Earth Wire, 0.5 m (x2) 2240 Reference Manual SMARTLINK-DIRECT-DUAL-6M package parts shown in an Envoy mobile system * *Computer and computer WiFi shown only for illustration. Computer is not supplied by Codan. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 199 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-NETWORK-CONSOLE PART NO. DESCRIPTION SmartLink Network Console This package can be used for connecting a SmartLink to an Envoy RF Unit via a CAT5e Ethernet cable (the Ethernet connection may be via network infrastructure or a direct cable connection). This package includes an interface cable for connecting a 2230 Desk Console to the SmartLink. The package contains the parts needed for adapting a standard Envoy base (Desk Console control point) configuration for use with the SmartLink over a network connection. An external DC supply is required for the SmartLink in this configuration Typical use case scenarios include base Envoy installations where the distance between the control point and RF Unit exceeds 30 m which is the maximum distance supported by standard Codan interface cabling. A continuous CAT5e Ethernet cable up to 75 m long can be used to connect the SmartLink to the Envoy RF Unit. The connection can also be made via IP network infrastructure such as a LAN, WAN etc. WiFi or Ethernet cable access to embedded Envoy data modems, via the SmartLink, is also supported. There is an added advantage of keeping the RF Unit 15-way and 6-way interfaces free for connection of accessories. ...continued next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 200 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-NETWORK-CONSOLE PART NO. DESCRIPTION COMPRISING: 08-07336-001 78-01263 08-07338-001 78-16019 67-9020# 67-90802 08-07215-001 15-04186-EN • • • • • • • • 2240 Envoy SmartLink WiFi Antenna, direct connect Cable, Envoy SmartLink to 2230 Console, 3 m SmartLink AC Mains Power Supply AC Mains Cable for SmartLink AC Mains PSU, 2 m Ethernet Cable, 2 m (x2) Cable, Transceiver to Ethernet Adaptor 2240 Reference Manual SMARTLINK-NETWORK-CONSOLE package parts shown in an Envoy base system * *Computer and computer WiFi shown only for illustration. Computer is not supplied by Codan. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 201 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-NETWORK-HANDSET PART NO. DESCRIPTION SmartLink Network Handset This package can be used for connecting a SmartLink to an Envoy RF Unit via a CAT5e Ethernet cable (the Ethernet connection may be via network infrastructure or a direct cable connection). This package assumes use of a 2221 or 2220 Handset to the SmartLink. The package contains the parts needed for adapting a standard Envoy base (Handset control point) configuration for use with the SmartLink over a network connection. An external DC supply is required for the SmartLink in this configuration. Typical use case scenarios include base Envoy installations where the distance between the control point and RF Unit exceeds 30 m which is the maximum distance supported by standard Codan interface cabling. A continuous CAT5e Ethernet cable up to 75 m long can be used to connect the SmartLink to the Envoy RF Unit. The connection can also be made via IP network infrastructure such as a LAN, WAN etc. WiFi or Ethernet cable access to embedded Envoy data modems, via the SmartLink, is also supported. There is an added advantage of keeping the RF Unit 15-way and 6-way interfaces free for connection of accessories. ...continued next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 202 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT SMARTLINK-NETWORK-HANDSET PART NO. DESCRIPTION COMPRISING: 08-07336-001 78-01263 78-16019 67-9020# 67-90802 08-07215-001 15-04186-EN • • • • • • • 2240 Envoy SmartLink WiFi Antenna, direct connect SmartLink AC Mains Power Supply AC Mains Cable for SmartLink AC Mains PSU, 2 m Ethernet Cable, 2 m (x2) Cable, Transceiver to Ethernet Adaptor 2240 Reference Manual SMARTLINK-NETWORK-HANDSET package parts shown in an Envoy base system * *Computer and computer WiFi shown only for illustration. Computer is not supplied by Codan. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 203 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT PART NO. 78-01263 DESCRIPTION WiFi Antenna, direct connect Gimbled WiFi antenna for direct connection to RP-SMA connector on 2240 SmartLink unit. 78-01265 WiFi Antenna, Mag-mount with 3 m cable Stub WiFi antenna with 3 m extension coaxial cable for connection to RP-SMA connector on 2240 SmartLink. Antenna has a magnetic base. Interface cable for connecting 2240 SmartLink directly to Envoy RF Unit. NOTE: This is the same cable used for connecting the Envoy 2230 Desk Console to the Envoy RF Unit 08-07205-001 08-07205-006 08-07205-010 08-07205-030 Cable, Envoy SmartLink to RF Unit, 1 m Cable, Envoy SmartLink to RF Unit, 6 m Cable, Envoy SmartLink to RF Unit, 10 m Cable, Envoy SmartLink to RF Unit, 30 m Linking cable used to link two SmartLink units together. 08-07337-001 08-07337-006 08-07337-010 Cable, Envoy SmartLink Linking, 1 m Cable, Envoy SmartLink Linking, 6 m Cable, Envoy SmartLink Linking, 10 m ...continued next page Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 204 2240 Smartlink Accessory Addendum 2240 SMARTLINK ACCESSORY PRODUCT PART NO. 08-07338-001 DESCRIPTION Cable, Envoy SmartLink to 2230 Console, 3m Interface cable for connecting 2230 Envoy Desk Console directly to 2240 Smartlink control point connector 78-16019 SmartLink AC Mains Power Supply The AC mains power supply is required for any SmartLink that does not have a direct connection to an Envoy RF Unit via Codan interface cables i.e. 08-07337-0XX linking and/or 08-07205-0XX RF Unit interface cables 67-9020# AC Mains Cable for SmartLink AC Mains Power Supply, 2 m For country type variants of AC Mains cables, (see page 119 of the HF Radio Communications International Product Catalogue) 08-04515-001 Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Earth Wire. 0.5 m Page 205 2240 Smartlink Accessory Addendum Cable lengths When two Envoy SmartLinks are linked using Codan control and linking cables from the same RFU, there are specific cable length combinations that may be used. Figure 1: Cable lengths between Envoy SmartLinks and RFU Table 1: Allowable lengths of Codan control and linking cables: If cable A is... cable B may be.. 1 m (08-07205-001) 1 m (08-07337-001) 6 m (08-07337-006) 10 m (08-07337-010) 6 m (08-07205-006) 1 m (08-07337-001) 6 m (08-07337-006) 10 m (08-07337-010) 10 m (08-07205-010) 1 m (08-07337-001) 6 m (08-07337-006) 30 m (08-07205-030) Not applicable NOTE: The 30 m variant of cable A (08-07205-030) is recommended for use in single Envoy SmartLink systems only. NOTE: These lengths assume that only one control point is connected per Envoy SmartLink. If you connect more than one control point per Envoy SmartLink, for example a handset to the control point connector and a desk console via an Ethernet cable, the lengths may need to be shorter. Codan Radio Communications Commercial Product Catalogue Issue 8 January 2015 Page 206 LONDON BEIJING 143
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2015:06:11 13:56:01+09:30 Modify Date : 2015:06:17 13:48:29+09:30 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2015:06:17 13:48:29+09:30 Format : application/pdf Document ID : uuid:ccdc38b2-b2fc-49af-ba1d-b014edd141d4 Instance ID : uuid:91c96da2-9cc4-4f26-b733-0ec45d3cca35 Page Mode : UseOutlines Page Count : 220EXIF Metadata provided by EXIF.tools