INDC260UG DC260_user_guide1 DC260 User Guide1

INDC260UG INDC260UG

User Manual: DC260_user_guide1

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadINDC260UG DC260_user_guide1 DC260 User Guide1
Open PDF In BrowserView PDF
Unit 1, AMC Business Park

t : 0208 621 6210

12 Cumberland Avenue

e : sales@doorentrydirect.com

Park Royal, London, NW10 7QL

w : www.doorentrydirect.com

User Guide
DC260 - stand alone access control unit for 2000 users

5 Adding Cards (or tokens)
Add a card (or token):
a. Enter Programming Mode (see 2)
b. Enter "1". Green & Red LED on.
c. Present card (or token) to the controller
(single green LED flash)
d. To add next card simply present the card to the
controller
e. To finish adding cards (or tokens) press #

" ".
d. Proceed to other functions or press "*" to

1 Setting the Programming code
Your installer will have set the “Programmer” code in
agreement with you.

complete the programming. (red LED flashing).
This is the fastest way to add cards as they can be
added continuously as the controller auto
generates the user ID incremental.

2 Entering Programming mode

Press
and enter your 6 to 8 programmers code
followed by # (red LED on).

To allocate the user ID manually simply enter the
ID number desired, prior to presenting
the card to the controller.
Only one user ID can be allocated to a single
card.

3 Initial setup

6 Deleting a card user

Before you can start adding users, you must run
initial setup procedure.

When you wish to delete a card you must either
have the card or know the user ID. You should also
modify the paper record of the card holder
against the user ID number being deleted.

Before you add or delete users, you must be in
Programming Mode, to do this:

"*"

" "

While in Programming Mode press "30" followed by

4 Setting the lock opening time

a. Enter programming mode (see 2)
b. Press “2” and present the card OR
enter the user ID to be voided

The controller has programmable
lock time of 01 to 99 seconds.

c. Press “#” to confirm (green LED lights up and a
“Beep” is heard as confirmation)

To set the lock time:
a. Enter Programming Mode (see 2)
b. Enter "4". Green & Red LED on.
c. Enter you chosen time (from 01 to 99 seconds)
followed by

"#".

"#".
"*" to

d. Proceed to other functions or press
complete the programming process.

Users can be deleted continuously without exiting
programming mode simply by presenting a new
card to be deleted or entering a new user ID
number and pressing “#” to confirm.

Appendix
DC260 - stand alone access control unit for 2000 users

7 Adding Cards (by number)

9 Default factory reset

Add a card (or token):
a. Enter Programming Mode (see 2)

Restoring to factory default, only installer data
is lost. Any card information or user ID will not be
affected.

b. Enter "1". Green & Red LED on.

a. Disconnect the power from the unit

c. Enter 8 digits printed on the back of the card

b. Press and hold “#” and apply power to the unit.

d. Press “#” to confirm (green LED lights up and a
“Beep” is heard as confirmation)

c. Once you hear 2x “Beeps” release the “#” and
the installer code is set to default.

e. To add another card, simply enter the 8 digits of
another card followed by “#”.

This is the fastest way to add cards as they can be
added continuously as the controller auto generates
the user ID incremental.

"*"

d. Proceed to other functions or press
to
complete the programming. (red LED flashing).
This is the fastest way to add cards as they can be
added continuously as the controller auto generates
the user ID incremental.

To allocate the user ID manually simply enter the ID
number desired, prior to presenting the card to the
controller.
Only one user ID can be allocated to a single card.

To allocate the user ID manually simply enter the ID
number desired, prior to presenting the card to the
controller.
Only one user ID can be allocated to a single card.

8 Deleting a card user (by number)

10 Delete all stored information

When you wish to delete a card you must either
have the card or know the user ID. You should also
modify the paper record of the card holder
against the user ID number being deleted.

NOTE: This is a dangerous option. Use with care!

a. Enter programming mode (see 2)
b. Press “2” and enter 8 digits printed on the back
of the card
c. Press “#” to confirm (green LED lights up and a
“Beep” is heard as confirmation)
Users can be deleted continuously without exiting
programming mode simply by entering 8 digit
number of the next card to be deleted and
pressing “#” to confirm.

a. Enter “Programming” mode
b. Press “2” and type “0000”
(green LED lights up and buzzer emits a “Beep”
as confirmation).
All stored information is now deleted.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Trapped                         : True
Author                          : KonradSamczyk
Creator                         : Serif DrawPlus 11, 0, 3, 23 (Feb 25, 14:12:55)
Title                           : INDC260UG
Create Date                     : 2017:06:13 08:41:33+01:00
Producer                        : PDFlib+PDI 6.0.0p2 (Win32)
EXIF Metadata provided by EXIF.tools

Navigation menu