DCR DVD110E/DVD115E/DVD310E/DVD410E/DVD610/DVD610E/DVD710/DVD710E/DVD810/DVD810E DCRDVD110
User Manual: DCRDVD110
Open the PDF directly: View PDF .
Page Count: 195
Download | ![]() |
Open PDF In Browser | View PDF |
DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E RMT-835 SERVICE MANUAL LEVEL Ver. 1.1 2008.03 Revision History Revised-1 Replace the previously issued SERVICE MANUAL 9-852-249-31 with this manual. Photo: DCR-DVD810 2 US Model Canadian Model AEP Model UK Model East European Model North European Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Japanese Model Link SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST • Precaution on Replacing the VC-520 Board The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DIGITAL VIDEO CAMERA RECORDER DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 9-852-249-32 Sony EMCS Co. 2008C0500-1 © 2008.3 Published by Kohda TEC These specifications are extracted from instruction manual of DCRDVD110E/DVD115E/DVD310E/DVD410E/DVD610E/DVD710E/DVD810E. ENGLISH JAPANESE SPECIFICATIONS System Video compression format MPEG2/JPEG (Still images) Audio compression format DCR-DVD110E/DVD610E Dolby Digital 2ch Dolby Digital Stereo Creator DCR-DVD115E/DVD310E/DVD410E/ DVD710E/DVD810E Dolby Digital 2/5.1ch Dolby Digital 5.1 Creator Video signal PAL color, CCIR standards Internal memory (DCR-DVD410E/ DVD810E) 8 GB When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for data management. Usable discs 8 cm DVD-RW/DVD+RW/DVD-R/ DVD+R DL Movie recording format Internal memory (DCR-DVD410E/ DVD810E) MPEG2-PS Disc DVD-RW: DVD-VIDEO (VIDEO mode), DVD-Video Recording (VR mode) DVD+RW: DVD+RW Video DVD-R/DVD+R DL: DVD-VIDEO “Memory Stick PRO Duo” MPEG2-PS Still image recording format Exif Ver.2.2* Viewfinder Electric viewfinder (color) Image device DCR-DVD110E/DVD115E/DVD610E 2.25 mm (1/8 type) CCD (Charge Coupled Device) Gross: Approx. 800 000 pixels Effective (Movie, 16:9) Approx. 490 000 pixels Effective (Still, 16:9) Approx. 310 000 pixels Effective (Still, 4:3) Approx. 410 000 pixels DCR-DVD310E/DVD410E/DVD710E/ DVD810E 3 mm (1/6 type) CCD (Charge Coupled Device) Gross: Approx. 1 070 000 pixels Effective (Movie, 16:9) Approx. 670 000 pixels Effective (Still, 16:9) Approx. 750 000 pixels Effective (Still, 4:3) Approx. 1 000 000 pixels Lens Carl Zeiss Vario-Tessar DCR-DVD110E/DVD115E/DVD610E Optical: 40×, Digital: 80×, 2000× DCR-DVD310E/DVD410E/DVD710E/ DVD810E Optical: 25×, Digital: 50×, 2000× Filter diameter: 30 mm (1 3/16 in.) Focal length Operating temperature DCR-DVD110E/DVD115E/DVD610E F 1.8 - 4.1 f = 1.9 - 76 mm (3/32 - 3 in.) When converted to a 35 mm still camera For movies: 41 - 1 640 mm (1 5/8 - 64 5/8 in.) (16:9) For still images: 48 - 1 920 mm (1 15/16 - 75 5/8 in.) (4:3) DCR-DVD310E/DVD410E/DVD710E/ DVD810E F 1.8 - 3.2 f = 2.5 - 62.5 mm (1/8 - 2 1/2 in.) When converted to a 35 mm still camera For movies: 41 - 1 189 mm (1 5/8 - 46 7/8 in.) (16:9)** For still images: 36 - 900 mm (1 7/16 - 35 1/2 in.) (4:3) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K) Minimum illumination DCR-DVD110E/DVD115E/DVD610E 6 lx (lux) (AUTO SLW SHUTTR ON, Shutter speed 1/25 second) 0 lx (lux) (during NightShot plus function) DCR-DVD310E/DVD410E/DVD710E/ DVD810E 8 lx (lux) (AUTO SLW SHUTTR ON, Shutter speed 1/25 second) 0 lx (lux) (during NightShot plus function) * “Exif” is a file format for still images, established by the JEITA (Japan Electronics and Information Technology Industries Association). Files in this format can have additional information such as your camcorder’s setting information at the time of recording. **The focal length figures are actual figures resulting from wide angle pixel readout. 0 °C to +40 °C (32 °F to 104 °F) Storage temperature -20 °C to +60 °C (-4 °F to +140 °F) Dimensions (Approx.) 55 × 89 × 130mm (2 1/4 × 3 5/8 × 5 1/8 in.) (w × h × d) including the projecting parts 55 × 89 × 130mm (2 1/4 × 3 5/8 × 5 1/8 in.) (w × h × d) including the projecting parts with the rechargeable battery pack NP-FH40 attached Mass (Approx.) DCR-DVD110E/DVD115E/DVD610E 390 g (13 oz) main unit only 440 g (15 oz) including the rechargeable battery pack NP-FH40 and a disc DCR-DVD310E/DVD710E 400 g (14 oz) main unit only 450 g (15 oz) including the rechargeable battery pack NP-FH40 and a disc DCR-DVD410E/DVD810E 400 g (14 oz)main unit only 445 g (15 oz) including the rechargeable battery pack NP-FH40 Supplied accessories AC Adaptor (1) Power cord (mains lead) (1) A/V connecting cable (1) USBcable (1) Wireless Remote Commander (DCRDVD310E/DVD410E/DVD710E/DVD810E) (1) Rechargeable battery pack NP-FH40 (1) CD-ROM “Handycam Application Software” (1) Operating Guide (1) See page 5-25. AC Adaptor AC-L200/L200B Power requirements • Manufactured under license from Dolby Laboratories. Current consumption Input/Output connectors Power consumption A/V Remote Connector Video/audio output jack USB jack AC 100 V - 240 V, 50/60 Hz 0.35 A - 0.18 A 18 W Output voltage DC 8.4 V* mini-B (DCR-DVD110E/DVD115E/DVD310E/ DVD410E: output only) Operating temperature 0 °C to +40 °C (32 °F to 104 °F) Storage temperature -20 °C to +60 °C (-4 °F to +140 °F) LCD screen Dimensions (Approx.) Picture 6.7 cm (2.7 type, aspect ratio 16:9) Total number of pixels 123 200 (560 × 220) General Power requirements DC 6.8 V/7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption Using the LCD screen or the viewfinder with normal brightness DCR-DVD110E/DVD115E/DVD610E LCD: 2.9 W Viewfinder: 2.7 W DCR-DVD310E/DVD710E LCD: 3.2 W Viewfinder: 2.8 W DCR-DVD410E/DVD810E LCD: 2.8 W Viewfinder: 2.4 W DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —2— 48 × 29 × 81mm (1 15/16 × 1 3/16 × 3 1/4in.) (w × h × d) excluding the projecting parts Mass (Approx.) 170g (6oz) excluding the power cord (mains lead) * See at the label of the AC Adaptor for other specifications. Rechargeable battery pack NP-FH40 Maximum output voltage DC 8.4 V Output voltage DC 7.2 V Capacity 4.9 Wh (680 mAh) Type Li-ion Design and specifications are subject to change without notice. These specifications are extracted from instruction manual of DCR-DVD610/DVD710/DVD810. ENGLISH JAPANESE SPECIFICATIONS System Video compression format MPEG2/JPEG (Still images) Audio compression format DCR-DVD610 Dolby Digital 2ch Dolby Digital Stereo Creator DCR-DVD710/DVD810 Dolby Digital 2/5.1ch Dolby Digital 5.1 Creator Video signal NTSC color, EIA standards Internal memory (DCR-DVD810) 8 GB When measuring media capacity, 1 GB equals 1 billion bytes, a portion of which is used for data management. Usable discs 8 cm DVD-RW/DVD+RW/DVD-R/ DVD+R DL Movie recording format Internal memory (DCR-DVD810) MPEG2-PS Disc DVD-RW: DVD-VIDEO (VIDEO mode), DVD-Video Recording (VR mode) DVD+RW: DVD+RW Video DVD-R/DVD+R DL: DVD-VIDEO “Memory Stick PRO Duo” MPEG2-PS Still image recording format Exif Ver.2.2* Viewfinder Electric viewfinder (color) Image device DCR-DVD610 2.25 mm (1/8 type) CCD (Charge Coupled Device) Gross: Approx. 680 000 pixels Effective (Movie, 16:9) Approx. 410 000 pixels Effective (Still, 16:9) Approx. 250 000 pixels Effective (Still, 4:3) Approx. 340 000 pixels DCR-DVD710/DVD810 3 mm (1/6 type) CCD (Charge Coupled Device) Gross: Approx. 1 070 000 pixels Effective (Movie, 16:9) Approx. 670 000 pixels Effective (Still, 16:9) Approx. 750 000 pixels Effective (Still, 4:3) Approx. 1 000 000 pixels Lens Carl Zeiss Vario-Tessar DCR-DVD610 Optical: 40×, Digital: 80×, 2000× DCR-DVD710/DVD810 Optical: 25×, Digital: 50×, 2000× Filter diameter: 30 mm (1 3/16 in.) Focal length Operating temperature DCR-DVD610 F 1.8 - 4.1 f = 1.9 - 76 mm (3/32 - 3 in.) When converted to a 35 mm still camera For movies: 41 - 1 640 mm (1 5/8 - 64 5/8 in.) (16:9) For still images: 48 - 1 920 mm (1 15/16 - 75 5/8 in.) (4:3) DCR-DVD710/DVD810 F 1.8 - 3.2 f = 2.5 - 62.5 mm (1/8 - 2 1/2 in.) When converted to a 35 mm still camera For movies: 41 - 1 189 mm (1 5/8 - 46 7/8 in.) (16:9)** For still images: 36 - 900 mm (1 7/16 - 35 1/2 in.) (4:3) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K) Minimum illumination DCR-DVD610 6 lx (lux) (AUTO SLW SHUTTR ON, Shutter speed 1/30 second) 0 lx (lux) (during NightShot plus function) DCR-DVD710/DVD810 8 lx (lux) (AUTO SLW SHUTTR ON, Shutter speed 1/30 second) 0 lx (lux) (during NightShot plus function) * “Exif” is a file format for still images, established by the JEITA (Japan Electronics and Information Technology Industries Association). Files in this format can have additional information such as your camcorder’s setting information at the time of recording. **The focal length figures are actual figures resulting from wide angle pixel readout. • Manufactured under license from Dolby Laboratories. Input/Output connectors A/V Remote Connector Video/audio output jack USB jack 0 °C to +40 °C (32 °F to 104 °F) Storage temperature -20 °C to +60 °C (-4 °F to +140 °F) Dimensions (Approx.) 55 × 89 × 130mm (2 1/4 × 3 5/ × 5 1/8 in.) (w × h × d) including the projecting parts 55 × 89 × 130mm (2 1/4 × 3 5/8 × 5 1/8 in.) (w × h × d) including the projecting parts with the rechargeable battery pack NP-FH40 attached Mass (Approx.) DCR-DVD610 390 g (13 oz) main unit only 440 g (15 oz) including the rechargeable battery pack NP-FH40 and a disc DCR-DVD710 400 g (14 oz) main unit only 450 g (15 oz) including the rechargeable battery pack NP-FH40 and a disc DCR-DVD810 400 g (14 oz)main unit only 445 g (15 oz) including the rechargeable battery pack NP-FH40 Supplied accessories AC Adaptor (1) Power cord (mains lead) (1) A/V connecting cable (1) USB cable (1) Wireless Remote Commander (DCRDVD710/DVD810) (1) Rechargeable battery pack NP-FH40 (1) CD-ROM “Handycam Application Software” (1) Operating Guide (1) See page 5-25. AC Adaptor AC-L200/L200B Power requirements AC 100 V - 240 V, 50/60 Hz Current consumption 0.35 A - 0.18 A Power consumption 18 W Output voltage DC 8.4 V* mini-B Operating temperature LCD screen 0 °C to +40 °C (32 °F to 104 °F) Storage temperature Picture 6.7 cm (2.7 type, aspect ratio 16:9) Total number of pixels 123 200 (560 × 220) -20 °C to +60 °C (-4 °F to +140 °F) Dimensions (Approx.) 48 × 29 × 81mm (1 15/16 × 1 3/16 × 3 1/4 in.) (w × h × d) excluding the projecting parts General Mass (Approx.) Power requirements 170 g (6 oz) excluding the power cord (mains lead) * See at the label of the AC Adaptor for other specifications. DC 6.8 V/7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption Using the LCD screen or the viewfinder with normal brightness DCR-DVD610 LCD: 2.9 W Viewfinder: 2.7 W DCR-DVD710 LCD: 3.3 W Viewfinder: 2.9 W DCR-DVD810 LCD: 2.9 W Viewfinder: 2.5 W DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —3— Rechargeable battery pack NP-FH40 Maximum output voltage DC 8.4 V Output voltage DC 7.2 V Capacity 4.9 Wh (680 mAh) Type Li-ion Design and specifications are subject to change without notice. ENGLISH JAPANESE 概略仕様 システム 映像圧縮方式 MPEG2/JPEG(静止画) 音声圧縮方式 Dolby Digital2/5.1ch ドルビーデジタル5.1クリエーター搭載 映像信号 NTSCカラー、EIA標準方式 内蔵メモリー 8GB 容量は、 1GBを10億バイトで計算した場合 の数値です。 また管理用ファイルなどを含む ため、 実際使用できる容量は若干減少する場 合があります。 使用可能ディスク 8cmのDVD-RW/DVD+RW/DVD-R/ DVD+R DL 動画記録方式 内蔵メモリー:MPEG2-PS ディスク: DVD-RW: DVD-VIDEO(VIDEOモード) DVD-Video Recording(VRモード) DVD+RW: DVD+RW Video DVD-R/DVD+R DL: DVD-VIDEO “メモリースティック PRO デュオ” : MPEG2-PS 静止画記録方式 Exif Ver.2.2* ファインダー 電子ファインダー (カラー) 撮像素子 3.0mm(1/6型)CCD固体映像素子 総画素数:約107万画素 動画時有効画素数 (16:9モード) : 約67万画素 静止画時有効画素数 (16:9モード) : 約75万画素 静止画時有効画素数 (4:3モード) : 約100万画素 ズームレンズ カール ツァイス バリオテッサー 25倍(光学) 50倍、2 000倍(デジタル) フィルター径30mm F1.8∼3.2 f=2.5∼62.5mm 35mmカメラ換算では 動画撮影時: 41∼1 189mm(16:9モード)** 静止画撮影時: 36∼900mm(4:3モード) 最低被写体照度 (オートスローシャッター 入、 8 lx(ルクス) シャッタースピード 1/30秒) (NightShot plus時) 0 lx(ルクス) * (社)電子情報技術産業協会(JEITA)にて制定 された、 撮影情報などの付帯情報を追加する ことができる静止画用のファイルフォーマッ ト。 ** 広角画素読み出しによる実動作値 入/出力端子 A/V リモート端子 映像音声出力端子 USB端子 mini-B 付属品 ACアダプター(1) 電源コード(1) A/V接続ケーブル(1) USBケーブル(1) ワイヤレスリモコン(1) リチャージャブルバッテリーパック NP-FH40(1) CD-ROM「Handycam Application Software」(1) 取扱説明書(1) 保証書 (1) ACアダプター AC-L200/L200B 電源 AC100V−240V、50/60Hz 液晶画面 画面サイズ 6.7cm(2.7型、アスペクト比16:9) 消費電力 18W 定格出力 総ドット数 123 200ドット 横560×縦220 電源部、その他 電源電圧 バッテリー端子入力 DC6.8V/7.2V DC端子入力 DC8.4V 消費電力 ファインダー使用時、 明るさ標準: 2.5W 液晶画面使用時、 明るさ標準: 2.9W DC8.4V* 動作温度 0℃∼+40℃ 保存温度 −20℃∼+60℃ 外形寸法 約48×29×81mm(最大突起部をのぞく) (幅×高さ×奥行き) 質量 約170g(本体のみ) * その他の仕様については AC アダプターのラ ベルをご覧ください。 動作温度 0℃∼+40℃ 保存温度 −20℃∼+60℃ 外形寸法 (突 55×89×130mm(幅×高さ×奥行き) 起部含む) (突 55×89×130mm(幅×高さ×奥行き) 起部含む、 付属バッテリーNP-FH40装着状 態) 本体質量 約400g(本体のみ) リチャージャブルバッテリーパック NP-FH40 最大電圧 DC8.4V 公称電圧 DC7.2V 容量 4.9Wh(680mAh) 使用電池 Li-ion 撮影時総質量 約445g(バッテリーNP-FH40含む) 本機の仕様および外観は、改良のため予告なく変 更することがありますが、 ご了承ください。 • ドルビーラボラトリーズからの実施権に基づ き製造されています。 色温度切り換え [オート] [ワンプッシュ] 、 、 [屋内] (3 200K) [屋外] 、 (5 800K) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —4— Model information table Non MEGA model Model Destination Color system 5.1ch recording Data copy DCR-DVD110E DCR-DVD115E AEP, UK, AEP, UK, EE, NE EE, NE PAL PAL × a CAM → PC PC → CAM Remote commander Active Interface Shoe Internal flash memory BL board CD board CK board MS board PD board RV board MEGA model Model Color system 5.1ch recording Data copy CAM → PC PC → CAM Remote commander Active Interface Shoe Internal flash memory BL board CD board CK board MS board PD board RV board DCR-DVD610E AEP, E, AUS, HK, CH PAL × a × a × a a a a × × × BL-021 CD-731 CK-191 MS-391 PD-351 RV-011 × × × BL-021 CD-731 CK-191 MS-391 PD-351 RV-011 × × × BL-021 CD-731 CK-191 MS-391 PD-351 RV-011 × × × BL-021 CD-731 CK-191 MS-391 PD-351 RV-011 DCR-DVD710 DCR-DVD710E US, CND, E, AR AEP, E, CH NTSC a DCR-DVD310E DCR-DVD410E Destination DCR-DVD610 US, CND, E, AR, BR NTSC × DCR-DVD810 DCR-DVD810E PAL a US, CND, E, KR, AR, JE, J NTSC a AEP, E, AUS, HK, JE PAL a AEP, UK, EE, NE PAL a AEP, UK, EE, NE PAL a a × a × a a a a a a a a a a × BL-022 CD-687 CK-192 MS-392 PD-352 RV-012 a a a BL-022 CD-687 CK-192 MS-392 PD-352 RV-012 a a × BL-022 CD-687 CK-192 MS-392 PD-352 RV-012 a a × BL-022 CD-672/CD-687 CK-192 MS-392 PD-352 RV-012 a a a BL-022 CD-687 CK-192 MS-392 PD-352 RV-012 a a a BL-022 CD-672/CD-687 CK-192 MS-392 PD-352 RV-012 • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model MX : Mexican model NE : North European model DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —5— ENGLISH JAPANESE CAUTION: The use of optical instrument with this product will increase eye hazard. CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. CAUTION Use of controls or adjustments or perfor mance procedures other than those specified herein may result in hazardous radiation exposure. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. 2. 3. 4. 5. 6. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —6— ENGLISH JAPANESE 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 サービス,点検時には次のことにご注意下さい。 1. 注意事項をお守りください。 サービスのとき特に注意を要する個所については, キャビネット,シャーシ,部品などにラベルや捺印で 注意事項を表示しています。これらの注意書き及び取 扱説明書等の注意事項を必ずお守り下さい。 2. 指定部品のご使用を セットの部品は難燃性や耐電圧など安全上の特性を 持ったものとなっています。従って交換部品は,使用 されていたものと同じ特性の部品を使用して下さい。 特に回路図,部品表に0印で指定されている安全上重要 な部品は必ず指定のものをご使用下さい。 3. 部品の取付けや配線の引きまわしはもとどおりに 安全上,チューブやテープなどの絶縁材料を使用した り,プリント基板から浮かして取付けた部品がありま す。また内部配線は引きまわしやクランパによって発 熱部品や高圧部品に接近しないよう配慮されています ので,これらは必ずもとどおりにして下さい。 4. サービス後は安全点検を サービスのために取外したネジ,部品,配線がもとど おりになっているか,またサービスした個所の周辺を 劣化させてしまったところがないかなどを点検し,安 全性が確保されていることを確認して下さい。 5. チップ部品交換時の注意 • 取外した部品は再使用しないで下さい。 • タンタルコンデンサのマイナス側は熱に弱いため交 換時は注意して下さい。 6. フレキシブルプリント基板の取扱いについて • コテ先温度を270℃前後にして行なって下さい。 • 同一パターンに何度もコテ先を当てないで下さい。 (3回以内) • パターンに力が加わらないよう注意して下さい。 7. 無鉛半田について 無鉛半田を使用している基板には,無鉛(Lead Free)を意 味するレッドフリーマークがプリントされています。 (注意:基板サイズによっては,無鉛半田を使用して いてもレッドフリーマークがプリントされて いないものがあります) :レッドフリーマーク 無鉛半田には,以下の特性があります。 • 融点が従来の半田よりも約40℃高い。 従来の半田こてをそのまま使用することは可能です が,少し長めにこてを当てる必要があります。 温度調節機能のついた半田こてを使用する場合,約 350℃に設定して下さい。 注意: 半田こてを長く当てすぎると,基板のパター ン(銅箔)がはがれてしまうことがあります ので,注意して下さい。 • 粘性が強い 従来の半田よりも粘性が強いため,IC端子などが半田 ブリッジしないように注意して下さい。 • 従来の半田と混ぜて使用可能 無鉛半田には無鉛半田を追加するのが最適ですが, 従来の半田を追加しても構いません。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 —7— 1. SERVICE NOTE ENGLISH JAPANESE 1-1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. These following method is available to prevent this. Method: Use the AC power adaptor (AC-L200/L200B). 1-2. TO TAKE OUT A DISC WHEN NOT EJECT (FORCE EJECT) 1 Open the jack cover and remove the remote control window. 2 Insert the wire etc. in the hole and down the eject slider by it. Charge Lever Eject Slider Remote Control Window Jack Cover Hole 1-3. PRECAUTION ON REPLACING THE VC-520 BOARD DESTINATION DATA When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”. USB SERIAL No. The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-1 ENGLISH JAPANESE 1-4. USING SERVICE JIG Connect the extension cable (J-6082-572-A) between the DVD mechanism deck and CN4401 on the VC-520 board. VC-520 board (side A) CN4401 Extension cable (10P) (J-6082-572-A) Flexible board (10P) DVD mechanism deck 1-5. SELF-DIAGNOSIS FUNCTION 1-5-1. Self-diagnosis Function 1-5-2. Self-diagnosis Display When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual. When problems occur while the unit is operating, the counter of the viewfinder or LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem. Viewfinder or LCD screen C:31:11 Blinks at 3.2 Hz C Repaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer 31 Block 11 Detailed Code Refer to “1-5-3. Self-diagnosis Code Table”. Indicates the appropriate step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-2 ENGLISH JAPANESE 1-5-3. Self-diagnosis Code Table Repaired by: Self-diagnosis Code Block Function Detailed Code Symptom/State Correction C 0 4 0 0 C 1 3 0 1 C 1 3 0 2 Disc access error E 2 0 0 0 Flash memory data are rewritten. E 3 1 0 0 Drive fault E 6 1 0 0 Difficult to adjust focus (Cannot initialize focus.) E 6 1 1 0 Zoom operations fault (Cannot initialize zoom lens.) The abnormalities in initialization of the focus lens and the abnormalities in initialization of the zoom lens occurred simultaneously. E 6 1 1 1 E 6 2 0 0 E 6 2 0 1 E 9 4 0 0 E 9 4 0 1 Non-standard battery is used. “Memory Stick Duo” is unformatted. “Memory Stick Duo” is broken. Handshake correction function does not work well. (With PITCH angular velocity sensor output stopped.) Handshake correction function does not work well. (With YAW angular velocity sensor output stopped.) Fault of writing to or erasing the flash memory Use the InfoLITHIUM battery. Format the “Memory Stick Duo”. Insert a new “Memory Stick Duo”. Clean the disc with the supplied cleaning cloth. Use a compatible disc with the camcorder. Make flash memory data correct value. (Note 1) Inspect or replacement of the mechanism deck, IC (IC4401 on the VC-520 board) and drive block. Inspect the lens block focus reset sensor (pin 7 of CN5101 on the VC-520 board) when focusing is performed when the focus buttons of the touch panel are pressed in the focus manual mode, and the focus motor drive circuit (IC5401 (Non MEGA model) or IC5301 (MEGA model) on the VC-520 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (pin qa of CN5101 on the VC-520 board) when zooming is performed when the zoom lever is operated, and the zoom motor drive circuit (IC5401 (Non MEGA model) or IC5301 (MEGA model) on the VC-520 board) when zooming is not performed. Check whether the flexible board of the lens is broken, and check whether it is inserted imperfectly. If there is no problem in the flexible board, inspect the focus/zoom motor drive circuit (IC5401 (Non MEGA model) or IC5301 (MEGA model) on the VC-520 board). Inspect PITCH angular velocity sensors (SE7002 on the CD672/CD-687 board) peripheral circuits. (MEGA model only) Inspect YAW angular velocity sensors (SE7001 on the CD-672/ CD-687 board) peripheral circuits. (MEGA model only) Inspect the flash memory (IC2101 on the VC-520 board). (Note 1) Inspect the internal flash memory (MDL4060S3C) (DVD410E/ DVD810/DVD810E only) Internal flash memory fault Note 1: Refer to “1-3. DESTINATION DATA WRITE”, ADJ (9-852-249-51). Note 2: Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-3 1. SERVICE NOTE ENGLISH JAPANESE 1-1. 修理時の電源供給について 本機では,安定化電源(8.4Vdc)からバッテリ端子に電源を供給した場合,約10秒後にシャットオフし,動作しなくなります。 これを避けるため,下記の方法を用いてください。 方法: DC入力端子を使用する。(ACアダプタ(AC-L200/L200B)を使用する。) 1-2. イジェクトしない時のディスク取出し方法(強制イジェクト) 1 ジャックカバーを開き,リモコン窓を外す。 2 穴に針金等を差し込み,イジェクトスライダを下げる。 チャージ レバー イジェクト スライダ リモコン窓 ジャックカバー 穴 1-3. VC-520基板交換時の注意 仕向けデータ 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 ADJ編を参照して,「DESTINATION DATA WRITE」を行ってください。 USBシリアルNo. セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。 新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。 ADJ編を参照して,「USB SERIAL No. INPUT」を行ってください。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-4 ENGLISH JAPANESE 1-4. 使用サービス治具 延長ケーブル(J-6082-572-A)をVC-520基板CN4401とDVDメカデッキの間に接続します。 VC-520基板(A面側) CN4401 延長ケーブル(10P) (J-6082-572-A) フレキシブル基板(10P) DVDメカデッキ 1-5. 自己診断機能 1-5-2. 自己診断表示 本機の動作に不具合が生じたとき,ビューファインダまたは LCD画面のカウンタ表示部分がアルファベットと数字の4桁 表示になり,3.2Hzで点滅します。この5文字の表示によっ て対応者分類および不具合の生じたブロックの分類,不具合 の詳細コードを示します。 1-5-1. 自己診断機能について 本機の動作に不具合が生じたとき,自己診断機能が働き, ビューファインダまたはL C D 画面に,どう処置したらよい か判断できる表示を行います。自己診断機能については取扱 説明書にも掲載されています。 ビューファインダまたはLCD画面 C:31:11 3.2Hz点滅 C 対応者分類 C :お客さま自身で対応 H :販売店で対応 E :サービスエンジニア で対応 31 ブロック分類 11 詳細コード 対応方法の違いにより分類 「1-5-3. 自己診断コード表」 例 31 ・・・テープを入れ直す を参照 32 ・・・電源を入れ直す DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-5 ENGLISH JAPANESE 1-5-3. 自己診断コード表 自己診断コード 対 ブロック 応 機能 者 詳細 コード C 0 4 0 0 標準以外のバッテリを使用している インフォリチウムバッテリを使用する。 C 1 3 0 1 フォーマットしていない“メモリー “メモリーステック デュオ”をフォーマットする。 ステック デュオ”を入れた “メモリーステック デュオ”が壊 新しい“メモリーステック デュオ”に交換する。 れている C 1 3 0 2 ディスクアクセスエラー E 2 0 0 0 フラッシュメモリが書き換えられて フラッシュメモリのデータを元の値に戻す(注) いる E 3 1 0 0 ドライブ不良 E 6 1 0 0 フォーカスが合いにくい タッチパネルでフォーカス操作をしたときにフォーカス動 (フォーカスの初期化ができない) 作をすれば,レンズブロックのフォーカスリセットセンサ (VC-520基板CN5101 7ピン)を点検する。フォーカス動 作をしなければフォーカスモータ駆動回路(VC-520基板 IC5301)を点検する。 E 6 1 1 0 ズーム動作の異常(ズームレンズの ズームレバーを操作したときにズーム動作をすれば,レン 初期化ができない) ズブロックのズームリセットセンサ(VC-520基板CN5101 qaピン)を点検する。ズーム動作をしなければズームモー タ駆動回路(VC-520基板IC5301)を点検する。 E 6 1 1 1 フォーカス,ズーム異常 フレキ切れ,半差し等の点検を行う。問題がない場合は フォーカス/ズームモータ駆動IC(VC-520基板IC5301)周 辺回路を点検する。 E 6 2 0 0 手振れ補正が効きにくい(PITCH 角速度センサ出力張り付き) PITCH角速度センサ(CD-672/CD-687基板SE7002)周辺回 路を点検する。 E 6 2 0 1 手振れ補正が効きにくい(YAW 角 速度センサ出力張り付き) YAW角速度センサ(CD-672/CD-687基板SE7001)周辺回 路を点検する。 E 9 4 0 0 フラッシュメモリの書込み/消去動 作不良 フラッシュメモリ(VC-520基板IC2101)を点検する。 (注) E 9 4 0 1 内蔵フラッシュメモリ不良 内蔵フラッシュメモリ(MDL4060S3C)を点検する。 症状/状態 対応/方法 ディスククリーニングをする。または本機に対応したディ スクに交換する。 メカデッキ駆動IC(VC-520基板 IC4401)周辺回路および 駆動部分を点検または交換する。 注:調整編(9-852-249-51)「1-3. DESTINATION DATA WRITE」を参照してください。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 1-6E 2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. • When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-1 Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) 2-1. IDENTIFYING PARTS BT/EVF Block ⋅ BL-021 Board ⋅ BL-022 Board ⋅ FP-839 Flexible Board ⋅ FP-841 Flexible Board Cabinet L ⋅ FP-569 Flexible Board Lens Block ⋅ CD-672 Board ⋅ CD-687 Board ⋅ CD-731 Board ⋅ FP-838 Flexible Board ⋅ FP-840 Flexible Board Cabinet R ⋅ CK-191 Board ⋅ CK-192 Board ⋅ FP-573 Flexible Board ⋅ FP-842 Flexible Board ⋅ MS-391 Board ⋅ MS-392 Board Mechanism Deck Main Frame LCD Block ⋅ PD-351 Board ⋅ PD-352 Board ⋅ RV-011 Board ⋅ RV-012 Board VC-520 Board Front Panel P Cabinet - DISASSEMBLY FLOW 2-2-1. OVERALL SECTION ⋅ Cabinet R ⋅ BT/EVF Block 2-2-2. CABINET R SECTION-1 ⋅ Front Panel ⋅ MS-391/392 Board ⋅ LCD Block 2-2-4. CABINET L SECTION ⋅ Cabinet L 2-2-3. CABINET R SECTION-2 ⋅ Hinge Block ⋅ CK-191/192 Board 2-2-5. MD Section ⋅ Lens Block ⋅ VC-520 Board ⋅ Mechanism Deck DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-2 HELP 2-2. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-2-1. OVERALL SECTION Follow the disassembly in the numerical order given. 1 Cabinet R (1-1 to 1-18) 2 BT/EVF Block (2-1 to 2-8) 2-6 (#11) 1-16 (#2) 1-15 (Open) 2BT/EVF Block Refer to page 1-1 “1-2. To take out a disc when not eject (force eject)". 2-7 DVD410E/DVD810/ DVD810E 2-2 2-5 (#3) 2-8 2-4 (#3) 2-3 (#2) 1-10 (#2) 2-1 Cabinet L Section 1Cabinet R (See Page 2-4) (See Page 2-6) 1-8 (#2) 1-17 1-13 (Claw) 1-6 1-3 (Claw) 1-18 1-14 1-7 1-2 (#2) 1-12 1-11 (Open) (Claw) 1-4 1-1 (Open) (Claw) 1-9 (#2) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-3 1-5 2-2-2. CABINET R SECTION-1 EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Front Panel (1-1 to 1-5) 2 MS-391/392 Board (2-1 to 2-2) 3 LCD Block (3-1 to 3-9) 2 MS-391/392 Board Cabinet R Section-2 2-1 (#11) (See Page 2-5) 2-2 (Claw) 1-2 (Claw) 1-3 (Boss) 1-1 (#11) 1 Front Panel 3LCD Block 1-4 (Claw) 3-7 3-8 1-5 (Claw) 3-3 (Claw) 3-9 (Claw) 3-5 (Claw) 3-1 (Rotate) 3-4 (Claw) 3-2 (#2) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-4 3-6 2-2-3. CABINET R SECTION-2 EXPLODED VIEW Follow the disassembly in the numerical order given. 1 Hinge Block (1-1 to 1-2) 2 CK-191/192 Board (2-1 to 2-5) 2-3 2-1 (Boss) 2 CK-191/192 Board 2-5 HELP 2 2-2 (Tripod Screw Ledge) 2-4 (#11) 1-1 (#11) 1-2 (Boss) 1 Hinge Block HELP 1 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-5 HARDWARE LIST 2-2-4. CABINET L SECTION EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Cabinet L (1-1 to 1-3) 1-1 (#11) 1-2 HELP 4 1-3 (#11) 1 Cabinet L HELP 3 MD Section (See Page 2-7) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-6 2-2-5. MD SECTION EXPLODED VIEW Follow the disassembly in the numerical order given. HARDWARE LIST 1 Lens Block (1-1 to 1-7) 2 VC-520 Board (2-1 to 2-3) 3 Mechanism Deck (3-1 to 3-3) 1Lens Block 3-1 (#16) 3-2 1-7 (#3) 1-4 3-3 DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E 2-2 1-5 DVD110E/DVD115E/ DVD610/DVD610E 1-6 DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E 2-3 3Mechanism Deck HELP 5 2VC-520 Board 0 52 VC 2-1 (#3) 1-3 1-2 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 2-7E 1-1 HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. HELP 1: THE METHOD OF ATTACHMENT OF FP-573 FLEXIBLE BOARD 1 Fold dotted line parts of the FP-573 flexible board as shown in figure. Valley fold Adhesive tape Mountain fold Adhesive tape Valley fold Mountain fold Stick it together in the adhesive tape while bending the FP-573 flexible board. 2 Install FP-573 flexible board in the Hinge Cover (M). 3 Install the Hinge Cover (C). Claw Adhesive tape Hinge Cover (M) FP-573 Claw Hinge Assy Hinge Cover (C) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 HELP HELP 2: SPEAKER HARNESS Speaker Harness Claw HELP 3: PRECAUTION WHEN INSTALLING THE CABINET L ASSY FOR SERVICE Cabinet L assy for service D lid block Screws When the eject block is installed on the cabinet L assy for service, a discrepancy could be made between the cabinet D block and the D lid block, and as a result, the D lid may not to be closed. In case of such discrepancy, loosen the screws on the hinge to eliminate the discrepancy of the D lid block, and then retighten the screws. Cabinet D block Eject block FP-569 flexible complete board M903 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 HELP HELP 4: FP-569 FLEXIBLE BOARD FP-569 Flexible Board Boss Motor Unit Boss HELP 5: MECHANISM DECK FLEXIBLE BOARD MD Frame Mechanism Deck Flexible Board Hook Hole Mechanism Deck Flexible Board DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 HELP 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/6) OVERALL BLOCK DIAGRAM (6/6) OVERALL BLOCK DIAGRAM (2/6) POWER BLOCK DIAGRAM (1/3) OVERALL BLOCK DIAGRAM (3/6) POWER BLOCK DIAGRAM (2/3) OVERALL BLOCK DIAGRAM (4/6) POWER BLOCK DIAGRAM (3/3) OVERALL BLOCK DIAGRAM (5/6) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. MEGA model LENS BLOCK CD-672/CD-687 BOARD IRIS (SHUTTER) Non MEGA model FP-838 FLEXIBLE BOARD CN7001 LENS BLOCK 12 CCD_OUT+ CCD IMAGER 1 - 6, 10, 12, 14, 15 IC7101 V1 - V6, RG, VSHT, H1, H2 Q7002 CLAMP 23, 20 - 15, 12, 10, 8 2 2 6, 9 - 14, 17, 19, 21 15 14 - 7, 5, 4 CCD_OUT 3 - 10, 12, 13 8 CN7101 7 - 2, 14, 18, 16, 19 CCD IMAGER CN1203 Q7101 BUFFER CN1201 27 CCD_OUT+ IC7002 VC-520 BOARD (1/7) CD-731 BOARD IRIS (SHUTTER) VC-520 BOARD (2/7) 7 22 2 4 25 12 PITCH/YAW 18 SENSOR AMP 2 27 19 3 26 V1 - V6, RG, H1, H2, SUB V1 - V6, RG, H1, H2, SUB V1 - V6, RG, VSHT, H1, H2 1 RCSUB Q7001 SE7002 PITCH SENSOR SE7001 YAW SENSOR 8 CSUB PITCH_AD IC7003 YAW_AD VST_C_RESET IC5102 (2/20) 1 5 6 IRIS DRIVE HALL AMP M 3 IRIS_BIAS (-) I_HALL_AD 7 I_BIAS (-) 17 I_BIAS (+) 15 I_HALL (+) Q5102 AMP 7 1 HALL GAIN HALL BIAS 5 1 2 3 EVR (D/A CONVERTER) (2/20) FC_SENS_OUT ZOOM SENSOR ZM_SENS_OUT LENS TEMP SENSOR THERMO_OUT 7 11 6 IR_SWITCH_OUT 19 ZOOM MOTOR DRIVE EN0, DIR0A, DIR0B M ZOOM MOTOR EN01, DIR1A, DIR1B M FOCUS_XA, FOCUS_A, FOCUS_XB, FOCUS_B ZOOM_A, ZOOM_XA, ZOOM_XB, ZOOM_B FOCUS SENSOR FC_SENSE_OUT ZM_RST ZOOM SENSOR ZM_SENSE_OUT LENS TEMP SENSOR TEMP_OUT XNS_SW IR_SWITCH_OUT NIGHTSHOT PLUS IRIS DRIVE Q5102 AMP HALL BIAS 3 2 1 IC5101 EVR (D/A CONVERTER) (2/20) 15 8 CAM_SO, CAM_SCK DA_STRB 16 HALL GAIN I_HALL_AD HALL AMP IC5103 IC5301 (2/20) (4/20) F3 F4 FC_RST LENS_TEMP_AD IRIS DRIVE OVERALL (2/6) (PAGE 3-2) 18 21 - 24 FOCUS MOTOR FOCUS MOTOR DRIVE 9 - 12 ZM_A, ZM_XA, ZM_XB, ZM_B (3/20) 23, 2, 21, 4 FC_XA, FC_A, FC_XB, FC_B FOCUS SENSOR 17 IC5401 5, 19, 17, 7 M IRIS_BIAS (+) DA_STRB IRIS_HALL (+) (2/20) 21 - 24 ZOOM MOTOR IRIS_HALL (-) 14 13 16 1-4 M CAM_SO, CAM_SCK 3 2 IC5103 FOCUS MOTOR 8 13 - 16 H 6, 7 H IC5101 IRIS_DRIVE (-) IRIS_DRIVE (+) 6, 7 18 1 OVERALL (2/6) (PAGE 3-2) IRIS_PWM IRIS_PWM 7 11 6 19 IRIS DRIVE E4 G1 CAM_DD_ON SHUTTER_ON FOCUS MOTOR DRIVE F5, G6, D3, E3 I_HALL (-) IRIS DRIVE Q5301 EN0, DIR0A, DIR0B ZOOM MOTOR DRIVE D5, B6, A6, C5 13 Q5401 CN5101 1-4 M CN5101 I_DRIVE (-) 2 IC5302 (4/20) IRIS METER F2, E2, D2, B1 IRIS METER (2/20) C6, B7, E6, D6 IC5102 EN01, DIR1A, DIR1B FC_RST ZM_RST LENS_TEMP_AD XNS_SW NIGHTSHOT PLUS 05 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E A : VIDEO SIGNAL DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-1 3-2. OVERALL BLOCK DIAGRAM (2/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-520 BOARD (3/7) A : VIDEO SIGNAL MEGA model CAM_DD_ON SHUTTER_ON SHUTTER_ON A/D CONVERTER, TIMING GENERATOR (1/20) C4 C5 A8 B6 H2 F4 AD2 - AD13 TG_VD TG_HD IC1701 (1/5) CPU (5/20 - 7/20) B10 D10 L17, M17, K16, L16 IC1201 K9, H9, J10, J6 V1 - V6, RG, H1, H2, SUB K4 H10, G8, F8, E8, C9, C8, C1, B7, B1, A1 CCD_OUT+ R4 AK33 AL34 H21 A14, C14, D12, A13, D13, C12, A12, B13, C13, D11, B12, B11 CSUB PITCH_AD YAW_AD VST_C_RESET B8 - B10, C7, C10, D8, D9, E9, E10, F9, F10, G9 CSUB PITCH_AD YAW_AD VST_C_RESET CH_CS, CH_SI, CH_SO, CH_SCK CHCK XSYS_RST CAM_DD_ON D9 IC2101 (8/20) EMC_DATA [0] EMC_DATA [31] OVERALL (1/6) (PAGE 3-1) 2 EMC_DATA [0] - EMC_DATA [31] X1201 24MHz: Non MEGA model 33MHz: MEGA model (NTSC) 27MHz: MEGA model (PAL) Non MEGA model CAM_SO, CAM_SCK DA_STRB I_HALL_AD IRIS_PWM DA_STRB I_HALL_AD IRIS_PWM EN0, DIR0A, DIR0B EN0, DIR0A, DIR0B EN01, DIR1A, DIR1B EN01, DIR1A, DIR1B FC_RST ZM_RST LENS_TEMP_AD XNS_SW FC_RST ZM_RST LENS_TEMP_AD XNS_SW EMC_ADDR [0] - EMC_ADDR [12], EMC_ADDR [14], EMC_ADDR [15] 512M SDRAM K17, J17 CAM_SO, CAM_SCK EMC_ADDR [0] EMC_ADDR [15] W2 G10 AK34 W1 L8, L9, J8 M7, N7, K8 IRIS_COM AF10 W25 W26 EMC_XCS [1] EMC_CLK0_OUT EMC_CLK0_IN J13 K11 EMC_DATA [0] - EMC_DATA [15] AE32 A5 AL35 C6 512M OneNAND FLASH EMC_ADDR [0] - EMC_ADDR [15] Non MEGA model OVERALL (1/6) (PAGE 3-1) 1 EN0, DIR0A, DIR0B EN01, DIR1A, DIR1B FC_RST ZM_RST LENS_TEMP_AD XNS_SW CAM_DD_ON XSYS_RST CCD_OUT+ V1 - V6, RG, VHST, H1, H2 CAM_SO, CAM_SCK DA_STRB I_HALL_AD IRIS_PWM AG10 Y25 EMC_CLK1_OUT Y26 AF16 EMC_XCS [0] EMC_CLK1_OUT EMC_XRESET_OUT XFLASH_RST U3 T4 P11 E8 XFLASH_RST XSYS_RST CAM_DD_ON 05 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-2 3 OVERALL (6/6) (PAGE 3-6) 3-3. OVERALL BLOCK DIAGRAM (3/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-520 BOARD (4/7) Y8 AC7 F1 XIC_4201_RESET XEJECT_SW OVERALL (6/6) (PAGE 3-6) FCE1Z XIC_4201_RESET Y7, AA6, AB7 AA17 P2 AA13 J12 L9 LPP, LPP2 ATTPLS L2 MSPDSH, WFPDSH, ROPCSH, RFPDSH RFMCLK M4 WLDON APCLOAD XRST_IC_4101 H2 L8 SDAT, SCS, SCLK TEMP TEMP FFDR, FRDR TFDR, TRDR FMPWN_OUT0, FMPWN_OUT1 FOCUS DRIVE FCS± TRACKING DRIVE TRK± TILT DRIVE TLT± SLED MOTOR DRIVE FP-569 FLEXIBLE BOARD S5692 LID_OPEN S5694 EJECT DETECT EJECT_DET SE4501 IC4501 SHOCK SENSOR SHOCK SENSOR AMP (18/20) 10 GSHCK D4 LID_OPEN 6 EJECT_DET 8 B3 A2 C12 B6 D5 D12 C11 Q4402 D5691 ACCESS ACCS_LED M EJECT_DRV 1 LED DRIVE ACCS_LED Y11 B12 3 SP_SPFD Q4401 SP_SPRD SV_FS4SV FGINI XMUTE0, XMUTE1 DRV_SEL PLG B5 B3 SPINDLE MOTOR DRIVE CN4401 SLED1 - SLED4 11 THERMISTOR FOCUS COIL TRACKING COIL TILT COIL M SLED MOTOR U, V, W M SPINDLE MOTOR A4 B7 B4, C4 S5693 LID OPEN DETECT 5 AB11, AA11 CN4402 XEJECT_SW 2, 3 S5691 OPEN G4, F4, G5, F5 SLSTFD1, SLSTRD1, SLSTFD2, SLSTRD2 C3, D3, E1 B7, D6, A5, C6 AC13 3-1 IC4101 RF PROCESS (11/20) AC12 X4201 33.8688MHz 25 - 18 27, 26 D2, E1, E2, F1, F2, G1, G2, H1 B1, C1 G11, H12 B12, A11 B11, A12 AWBL DWBL C8, D7 4 B4 M9 A6, C7 XIC_4201_RESET_A FEA0 - FEA19 RECD1 C4, C3 16M FLASH (10/20) H11 A8 37 - 34 FDQ0 - FDQ15 IC4302 M1 SWRF EQRF_S 41 - 38 AB8 FPD IC 45 - 42 B1 50 2-5 AB6 30 8-6 B19 A16 VC FPDIC_OUT C7, D5 AA3, AA8 XSDCS SDCLK Y6, AA4, AB4, AB3 19 38 BH1, BH2 A2 D6, D7 U2 AB2 SDA0 - SDA11 PH1, PH2 PDIC_GAIN E7, F6 64M SDRAM (10/20) C2 C11 E11 PD IC M10, L10 IC4303 PI CE A-H LASER DIODE L3, L4, M2, M3 B2, T4 SDDQ0 - SDDQ15 C12 D11 LD DRIVE L11, M11 R1 H1 FE TE RF± 12 L6, L7, M6 Y5, AB5, AA5 N2, P4 J4 L1 MPXOUT1, MPXOUT2 E5, H6 TXD_TO_IC_4201, RXD_TO_IC_4201, XSCK_IC_4201, XCS_IC_4201 DVD DSP, DVD DRIVE CONTROL (9/20) K4 L4 ENBL G6, H7 D13, B13, C13, B14 R23 IC4201 LD_EN G7, H8 XATA_RESET CN4103 LDD_W1DIS - LDD_W3DIS WP1_OP - WP3_OP E4, F2, G1, G2 ATA_A0 - ATA_A2 Y12 K2, K3 J3, N3 J2, P1 H21, J21, H22 L22, L20, M22, N21, P20, P21, P23, R22, R21, P22, N20, N22, M21, M20, L21, R20 ATA_D0 - ATA_D15 AL4 G19, H18, G18, H19 CPU (5/20 - 7/20) AH12, AH14, AJ12, AN12, AH11, AJ11, AJ13, AH9, AJ14, AH8, AH13, AH10, AM9 - AM11 AJ8, AJ10, AM12, AJ9 IC1701 (2/5) DVD MECHANISM DECK (DDX-C2000) B8 H1 F3 IC4401 DVD MECHA DRIVE (12/20) EJECT MOTOR DRIVE A : VIDEO/AUDIO/SERVO SIGNAL A : VIDEO/AUDIO SIGNAL A : SERVO SIGNAL M903 MOTOR UNIT (GEARD MOTOR) 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-3 3-4. OVERALL BLOCK DIAGRAM (4/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. MEGA model 18 43 3 31 27 - 25 EVF_BL_ON PANEL_BL_ON TP_X TP_Y 14 16 TP_SEL1 15 PANEL_VR PANEL_VG PANEL_VB COM HST, HCK1, HCK2, VCK, PCG, REF, VST, EN, PSIG RGT, DWN, XSTBY TP_X TP_Y TP_SEL1 CN6201 (1/2) + 2 – 1 LCD BACKLIGHT DRIVE 11 - 9 3 BL_H1 - BL_H3 PSIG, HCK1, HCK2, REF, HST, PCG, EN, VCK, VST RGT, DWN, XSTBY CN6204 TP_TOP 5 TP_L 2 17 15 TOUCH PANEL I/F Q6201, Q6202 TP_R TP_BOT D6203 – D6205 (BACKLIGHT) Q3101 - Q3104 IC3102 (1/2) COM, CS 1 Q1701 TOUCH PANEL SELECT SWITCH 4, 8 - 11, 13, 15 - 17 CN6201 (1/2) LCD901 CN6205 R 4 G 5 B 3 30 29 28 16 PD-352 BOARD (1/2) 1 4 LCD901 CN6205 R 4 G 5 B 3 30 29 28 COM, CS 1 2.7 inch WIDE COLOR LCD UNIT TOUCH PANEL PSIG, HCK1, HCK2, REF, HST, PCG, EN, VCK, VST RGT, DWN, XSTBY CN6204 TP_TOP 5 TP_L 2 17 15 16 6 - 8, 11 - 13, 20 - 22 1, 24, 23 17, 19 - 24, 28, 29 EVF_BL_ON PANEL_BL_ON MEGA model PD-351 BOARD (1/2) FP-573 FLEXIBLE BOARD (1/2) 30 TP_SEL2 D5701 (BACKLIGHT) Non MEGA model 1 2 3 B28 1 1 Q3105 EVF BACKLIGHT DRIVE 7 CN3102 (1/2) B29 12 28 CPU (5/20 - 7/20) AM35 AN34 WIDE COLOR EVF UNIT 11 D5702 (BACKLIGHT) EVF BACKLIGHT CONTROL (16/20) D26 Y4 EVF_STB 12 LCD902 TOUCH PANEL I/F Q6201, Q6202 TP_R TP_BOT 2.7 inch WIDE COLOR LCD UNIT 2, 19, 14 EXTDA J21 EVF_COM 14, 12 - 7, 3, 2 XCS_LCD XBB_RST 18 19 17 21 EVF_HST, EVF_HCK1, EVF_HCK2,EVF_VCK, EVF_PCG, EVF_REF, EVF_VST, EVF_EN, EVF_PSIG 4-6 BB_SI, BB_SO, XBB_SCK LED_K IC3102 (2/2) IC1701 (3/5) 4, 8 - 11, 13, 15 - 17 2 - 4, 6, 8 - 11, 15 6 - 9, 12, 14, 16, 30, 24 48, 1 K1, K2 IC2401 D/A CONVERTER (13/20) – 5 + XCS_LCD 12 STB 6 T27 EVF_STB COLOR EVF UNIT CN5702 EVF_VR EVF_VG EVF_VB 1 4 TOUCH PANEL 20 - 22 XBB_RST G20 7 6 5 7 3 LCD902 24, 23 BB_SI, BB_SO, XBB_SCK H2 10 HST, HCK1, HCK2, VCK, PCG, REF, VST, EN, PSIG 6 - 8, 11 - 13, 20 - 22 L18, M19, M18 U27 5 OVERALL (5/6) (PAGE 3-5) EVF_COM EVF_HST, EVF_HCK1, EVF_HCK2,EVF_VCK, EVF_PCG, EVF_REF, EVF_VST, EVF_EN, EVF_PSIG 2, 19, 14 XCS_IC_2401 E21 IC_2401_Y_OUT IC_2401_C/PB_OUT 6 5 7 3 14, 12 - 7, 3, 2 DR_VINCK F35 D12 LCD/EVF DRIVE (16/20) EVF_VR EVF_VG EVF_VB 20 - 22 G35 IC3101 13 14 12 16 CN5702 VR 17 VG 18 VB 16 CS, COM 4-6 DR_GSPILOT 20 21 22 26 BL-022 BOARD CN5701 5, 11, 18 G32, G34, F32, F34 DR_GSDATA0 – DR_GSDATA3 PANEL_HD, PANEL_VD BB_SO, XBB_SCK B15 34 33 32 42, 45, 44 DR_GHPILOT B16, A16, B17, A17, D18, B18, A15, A14 A18, B19, A20, B21 DR_GHDATA0 – DR_GHDATA3 H35 AA9 AA11 D14, B14, D13, A13 DR_VDATA0 – DR_VDATA7 PANEL_R PANEL_G PANEL_B AA2 AA4 AA5 BL-021 BOARD CN5701 5 - 7, 10, 12 - 15, 20 19, 21 CN3101 J1, G2, H1 E32, G33, D35, E34, D33, D34, E33, F33 D32, C34, B33, C33 VC-520 BOARD (5/7) 5 - 7, 11, 13 - 16, 20 Non MEGA model D6203 – D6205 (BACKLIGHT) LCD BACKLIGHT CONTROL (16/20) Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E A : VIDEO SIGNAL 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-4 3-5. OVERALL BLOCK DIAGRAM (5/6) A : VIDEO SIGNAL A : AUDIO SIGNAL VC-520 BOARD (6/7) MEGA model FP-840 FLEXIBLE BOARD (1/2) CN901 HOT SHOE (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 3 3 2 2 CN1008 (1/2) MIC_FL SHOE_MIC_FL MIC_FR SHOE_MIC_FR A11 B10 DVD115E/DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E FRONT 6 L 2 R 4 DVD115E/DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E INT_MIC_F A10 INT_MIC_L B14 INT_MIC_R B13 CN1005 IC2801 IC_2401_Y_OUT IC_2401_C/PB_OUT 5 OVERALL (4/6) (PAGE 3-4) N4 N3 VIDEO, AUDIO I/O (15/20) CN1012 S_Y/D3_Y 10 S_C/D3_Pb 5 VIDEO/D3_Pr 9 Y_TO_Y K1 C_TO_PB M2 V_TO_PR L1 K13, J13 MIC901 MICROPHONE UNIT BB_SO, XBB_SCK A/V R J14 P12 N13 P13 N14 M14 M13 A4 K14 AUDIO_L AUDIO_R JACK_AD LANC_SIG F2 G1 C14 C13 1 6 7 2 Non MEGA model CK-191 BOARD (1/2) ACCESS_LED CN5801 (1/2) 2, 3 CN1002 (1/2) SP± 2, 3 XCS_IC_2801/IC_2901 ADA_SIA0 ADA_SOA0 ADA_SOA1 ADA_FCK ADA_BCK ADA_LRCK SYS_SOUND B1, C2 U26 R29 N28 P29 M29 M28 N29 R35 SP± 9 9 D5801 (MS ACCESS) SP901 SPEAKER MEGA model 33 32 18 16 CK-192 BOARD (1/2) 11 SCLK AJ34 FM_CLK AG29 AM30, AN33, AN30, AM32 AE28, AF28, AH28, AG28 FM_BIO0 - FM_BIO3 H23 AM31 AR32 FP-842 FLEXIBLE BOARD (1/2) CN1003 (1/2) XMS_IN XMS_ACC_LED MSX_BIO0 - MSX_BIO3 MSDATA0 - MSDATA3 MSX_BS MSX_CLK MS_BS MS_SCLK USB_D± USB DETECT USB_VCC CN7301 (1/2) 10 11 5 6 12 CN7302 XMS_IN MSDATA0 - MSDATA3 MSBS MS_SCLK 6 MEMORY STICK DUO 2 8 MEGA model Q1001 XVBUS_DET 2 8 3, 2 W35, V35 USB_D± MEMORY STICK DUO MS-392 BOARD (1/2) 7 CN1004 G25 MSBS MS_SCLK 6 4, 3, 5, 7 8, 7, 9, 11 JACK_AD CN7302 XMS_IN MSDATA0 - MSDATA3 6 12 XSYS_RST LANC_SIG XMS_IN 8, 7, 9, 11 4 3, 5, 7, 9 12, 10, 8, 6 FLASH MEMORY (MDL4060S3C) (8GB) MS-391 BOARD (1/2) 9, 10, 8, 6 DVD410E/DVD810/DVD810E XFM_IN AP6 FM_BS AE29 Non MEGA model DVD110E/DVD610/DVD610E OVERALL (6/6) (PAGE 3-6) 7 13 D5801 (MS ACCESS) 10 6 CN1006 INS 8 BS 2 SDIO/DATA0, DATA1 - DATA3 9 CN7301 (1/2) CPU (5/20 - 7/20) FP-841 FLEXIBLE BOARD 42 44 36 34 SP901 SPEAKER 4, 3, 5, 7 IC1701 (4/5) IC2901 VIDEO OUT, AUDIO I/O (14/20) SP± 2, 4 28 20 21 23 24 22 47 CN5801 (1/2) 2, 3 27, 26 11 14 12 (USB) 1 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-5 3-6. OVERALL BLOCK DIAGRAM (6/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-520 BOARD (7/7) CN901 HOT SHOE 11 (2/2) 12 9 10 HOTSHOE_ID1, HOTSHOE_ID2 ID1, ID2 STROBE LANC EXT_STROBE B3 N3 IC1701 (5/5) MS-392 BOARD (2/2) S7301 PANEL OPEN/CLOSE PANEL_O/C Non MEGA model 2 XFR_SCK, FR_SI, FR_SO, XCS_EX XHOT_STBY STABLE_RUN WD_DIS BOOT_MODE_PORT0 XSYS_RST CAM_DD_ON C23 V2 G23 AA1 G2 AM7 CPU (5/20 - 7/20) FP-842 FLEXIBLE BOARD (2/2) CN7301 (2/2) A_2.8V CAM_DD_ON XSYS_RST XFLASH_RST 3 OVERALL (2/6) (PAGE 3-2) CN1003 (2/2) 15 PANEL_O/C KEY_AD0 KEY_AD3 PANEL_NOR/REV PANEL_O/C AH35 AH33 H25 G24 XIC_4201_RESET XEJECT_SW 4 OVERALL (3/6) (PAGE 3-3) 3 14 Y3 Q1002 LED DRIVE CN7301 (2/2) IR_LED_ ON 6 CK-192 BOARD (2/2) CN5801 (2/2) CN1002 (2/2) 5 5 RESET (18/20) S5802 DISP/ BATT INFO 6 6 S5801 RESET 8 S5801 RESET 8 8 7 BT901 LITHIUM BATTERY PD-352 BOARD (2/2) S7601 PANEL REVERSE CN6201 (2/2) FP-573 FLEXIBLE BOARD (2/2) CN6201 (2/2) NOR_REV 13 18 7 XBATT_VIEW HI_XRESET FR_XRESET BATT_LI_3V H6 D9 J5 F8 K5 E10 D10 D11 G9 C10 E8 B11 E9 D4802 RV-012 BOARD PD-351 BOARD (2/2) 1 XUNREG_RESET XBATT_VIEW 13 18 CN3102 (2/2) PANEL_NOR/REV 18 KEY_AD0 13 C3, B3, D4 7 BT901 LITHIUM BATTERY 1.8/3VCTRL FR_XRESET CAM_DD_ON VTR_DD_ON 1.8/3VCTRL LANC_SIG LANC_IN LANC_OUT XLANC_ON XLANC_PWR_ON BATT_IN FR_EVER_SO, FR_EVER_SCK, XCS_DD IC4801 S001 START/STOP W S003 (ZOOM) T S002 START/STOP HOME _SW 2ND_SS _SW 2ND_ ZOOM (W) 2ND_ ZOOM (T) CONTROL SWITCH BLOCK (SB22100) CN6202 6 S004 HOME 3 S001 START/STOP 5 W S003 (ZOOM) 4 RV001 W y T (ZOOM) ZOOM_VR_AD 7 S001 START/ STOP S/S 13 S002 (PHOTO FREEZE) C8 B3 KEY_AD1 HI CONTROL (17/20) KEY_AD2 S004 QUICK ON KEY_AD2 2 T S002 HOME _SW 2ND_SS _SW 2ND_ ZOOM (W) 2ND_ ZOOM (T) PHOTO S003 (PHOTO REC) KEY_AD1 8 B6 S005 BACK LIGHT C2 B4 A2 XPOWER_SW XMODE_SW OFF (CHG) r ON POWER r MODE XPOWER_SW XMODE_SW 10 11 DC CONTROL, RESET, LANC DRIVE (19/20) CN6202 6 3 5 4 05 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-6 AU_4.6V, A_4.6V MT_5.0V, DRV_MT_5.0V D_2.8V, AU_2.8V, A_2.8V DRV_MT_4.3V D_2.5V, A_2.5V D_1.2V, A_1.2V DRV_A_3.9V D_1.8V D_3.3V CAM_-7.5V CAM_15/12V EP_8.5V VOUT LANC_DC EVER_3.0V FP-839 FLEXIBLE BOARD B2 K2 C7 12 SHOE_UNREG, DRV_UNREG, MT_BL_UNREG, VTR2_UNREG, VTR_UNREG F2 C11 B10 C10 H2 C1 A7 CN1001 BATT/XEXT F10 E11 INIT_CHARGE_ON FAST_CHARGE BATT_UNREG A4 LF1002 BATT_SIG BATT_XEXT 1 - 5 7 - 11 6 CONTROL SWITCH BLOCK (SB22100) ZOOM_VR_AD LANC_SIG S5802 DISP/ BATT INFO NOR_REV D003 PHOTO XPHOTO_LED 17 X4901 32.768kHz KEY_AD3 S5803 DUBBING 5 S7601 PANEL REVERSE D002 CAM S006 EASY DVD410E/DVD810/DVD810E CN5801 (2/2) RV-011 BOARD XCAM_LED ACV_UNREG 13 - 17 2 IC4601 S5806 N XPHOTO_LED D001 CHG D1005 (NIGHTSHOT) S5806 N CK-191 BOARD (2/2) 16 XCHARGE_LED IC4901 XSYS_RST XMS_IN LANC_SIG OVERALL (5/6) (PAGE 3-5) D30 XCAM_LED L2 L3 15 BATT_UNREG J001 DC IN ACV_GND Q4601, Q4602 Q4603, Q4604 D4601 19 20 - 24 PANEL_O/C SIRCS_SIG F11 CN1013 XCHARGE_LED B8 D2, D1, G1 S7301 PANEL OPEN/CLOSE SIRCS_SIG G11 E10 E9 D9 H9 A8 IC7301 REMOTE 3 COMMANDER RECEIVER MS-391 BOARD (2/2) S004 HOME K5, J4, L5, H3 5, 8 7, 10 CN1008 (2/2) CONTROL KEY BLOCK (PS26100) X1701 12MHz AK3 AJ33 H26 AH34 AJ35 A22, B22, C22, D22 FP-840 FLEXIBLE BOARD (2/2) XPHOTO_LED ZOOM_VR_AD START/STOP KEY_AD1 KEY_AD2 AM34, AM33 MEGA model BATT_SIG BATT_GND + C − BH001 BATTERY TERMINAL VC-520 BOARD (1/3) MEGA model SHOE_UNREG F001 DRV_UNREG F002 MT_BL_UNREG F003 VTR2_UNREG F004 VTR_UNREG UNREG 12 ACV_UNREG LF1002 ACV_REG_GND BATT_XEXT Q4601, Q4602 Q4603, Q4604 UNREG CN901 HOT SHOE SHOE_ON 1 - 5 7 - 11 CN1001 J001 DC IN FP-840 FLEXIBLE BOARD CN1008 Q4605, Q4606 F005 6, 7 FP-839 FLEXIBLE BOARD ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 8, 9 3-7. POWER BLOCK DIAGRAM (1/3) SHOE_ON – BATT_SIG FAST_CHARGE 19 F006 INIT_CHARGE_ON C D4801 BATT_UNREG BATT_SIG BATT_XEXT + 13 - 17 BH001 BATTERY TERMINAL 20 - 24 D4601 H5 K4 K2 C4 Non MEGA model XFLASH_RST XIC_4201_RESET XSYS_RST CK-191 BOARD CN5801 (1/2) (1/2) S5801 RESET XFLASH_RST XIC_4201_RESET XSYS_RST CN1002 (1/2) BATT_LI_3V 7 HI_XRESET 8 7 BT901 LITHIUM BATTERY A9 VCC1 A10 VCC2 E11 VCC3 D POWER (2/3) (PAGE 3-8) PVCC1 L3 SW1 J4 IN1 G8 CH5LH CH7L/H CH8A RST D4802 E9 VCH PVCC2 F1 SW2 F2 IN2 D7 L4802 PVCC3 B1 SW3 C2 IN3 C6 L4803 EVER_3.0V LANC_DC VREGD F4 HVREG E3 XUNREG_RESET IC4601 1 OUT CK-192 BOARD CN5801 (1/2) (1/2) 7 C9 VRO F9 VOUT4 B10 VOUT RESET (18/20) VDD 2 VOUT BATT_UNREG VTR_UNREG MEGA model C2 P06_INT10 FR_XRESET S5801 RESET AU_4.6V L4813 A_4.6V L4821 MT_5.0V L4822 DRV_MT_5.0V L4818 D_2.8V L4823 AU_2.8V D4803 L4824 A_2.8V PVCC4 L2 SW4 K1 IN4 B9 L4804 L4817 DRV_MT_4.3V PVCC5 A2 SW5 B4 IN5 J7 L4805 L4819 D_2.5V L4820 A_2.5V XSYS_RST XIC_4201_RESET XFLASH_RST BATT_SIG BATT/XEXT FAST_CHARGE INIT_CHARGE_ON A/V R CN1012 LANC_DC PVCC6 G1 SW6 G2 IN6 J10 L4806 D_1.2V Q4804 P30_AN00 J5 P31_AN01 L6 A8 P65 C8 P66 B8 P64 A4 C7 E11 F10 L4814 A_1.2V L4809 DRV_A_3.9V L4815 D_1.8V CLAMP K2 RSTX J7 P33_AN03 8 4 L4811 D4805 B11 VBAT D9 XRESET FR_XRESET 8 BT901 LITHIUM BATTERY L4801 Q4801 L4808 SWITCHING A POWER (2/3) (PAGE 3-8) GATE8 D5 SW8 C5 IN8 J8 SIO2 P71_INT01 P53 P52 D4804 VREG7 H8 VREG8 K11 REG78CTL H6 IC4802 3.3V REG (19/20) D001 CHG 14 IC4801 IC4901 CN1013 (1/2) CHARGE_LED_VDD B4 P00_INT04 A2 P03_INT07 CAM_-7.5V MEGA model L4807 MODE P11_SO1 P12_SCK1 P21_PPG01 P07_INT11 C1 P23 H2 P70_INT00 P20_PPG00 P61_PPG11 P22 P34_AN04 A7 F2 C11 G2 L7 FR_EVER_SO, FR_EVER_SCK, XCS_DD XLANC_POWER_ON XLANC_ON BATT_IN VTR_DD_ON 1.8/3VCTRL CLAMP_ON D4, B3, C3 XPOWER_SW 10 XMODE_SW 11 Q4806, Q4808 D4806 -7.5V REG G1, D1, D2 ON D_3.3V R1008 OFF (CHG) POWER 1 CE 4 VDD VOUT 3 DC CONTROL, RESET, LANC DRIVE (19/20) HI CONTROL (17/20) 1.8/3VCTRL CLAMP_ON CONTROL KEY BLOCK (PS26100) (1/2) DIN CLK LD C10 WAKE_UP G9 XCTL2 E8 CS F8 STBY6 K5 STB PVCC7 L6 SW7 K6 IN7 H10 Q4802 Q4803 SWITCHING 15V REG R4835 Q4805 8.5V REG VCONT5 H7 VOUT5 K7 Non MEGA model VCONT6 L7 VOUT6 J6 REG6CTL J5 CAM_15/12V CAM_DD_ON EP_8.5V A_4.6V MT_5.0V A_2.8V D_2.8V D_2.5V B POWER (3/3) (PAGE 3-9) Q4807 12V REG Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-7 3-8. POWER BLOCK DIAGRAM (2/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. FP-838 CD-672/CD-687 BOARD FLEXIBLE CN7001 BOARD VC-520 BOARD (2/3) Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CAM_-7.5V CAM_15/12V CAM_-7.5V CN1201 CAM_-7.5V CAM_15/12V CAM_15V A_2.8V SE_2.8V FB7001 5 24 4 25 28 1 26 3 SE7001 YAW SENSOR IC7002 L7001 CCD IMAGER IC7003 L7002 PITCH/YAW SENSOR AMP X1201 VST_C_RESET CAM_DD_ON XSYS_RST RESET G2 XATA_RESET CF_Reset/ATA_RESET AL4 EMC_XRESET_OUT EMC_XRESET_OUT AF16 XSYS_RST CAM_DD_ON CAM_DD_ON CAM_12.0V B6 RESET H2 DS_GATE DVD410E/DVD810/DVD810E G13, G12 GPIO_S[14] EXIO_DIR GPIO_S[13] SIR_TXD H20 AN6 G20 Y4 MEGA model C IRIS DRIVE (4/20) IC5102 IC5103 IRIS DRIVE, HALL BIAS CONTROL (2/20) HALL BIAS/GAIN CONTROL (2/20) IC5103 HALL AMP, HALL GAIN CONTROL (2/20) IC5401 IC5301 FOCUS/ZOOM MOTOR OUT7A F4 DRIVE, IRIS DRIVE (4/20) L5101 ZOOM SENSOR 8 FOCUS SENSOR 13 IRIS METER XIC_4201_RESET XATA_RESET AA13 XRST R23 ATXRST XIC_4201_RESET_A IC4201 Q2901 3.6V REG IC2401 L4202 DVD115E/DVD310E/DVD410E/ DVD710/DVD710E/ DVD810/DVD810E FB4203 IC2901 L2903 VIDEO OUT, AUDIO I/O (14/20) XSYS_RST FB4302 DVD DSP, DVD DRIVE CONTROL (9/20) PD1 AC7 L2902 LENS BLOCK SHOCK SENSOR AMP (18/20) FB4201 D_1.2V DVD110E/DVD610/DVD610E Non MEGA model IC4501 A_2.8V D_2.8V MT_5.0V A_2.8V D_2.8V MT_5.0V EVR (D/A CONVERTER) (2/20) L2905 10 MT_5.0V_LD A_2.8V IC5101 XRST_IC_4101 FB4301 CN5101 ZM_SENS_Vcc FC_SENS_Vcc B4 RESET# R5402 I_DRIVE (+) L2805 VIDEO, AUDIO I/O (15/20) AU_2.8V AU_2.8V L2801 AU_4.6V AU_4.6V L2802 8 FOCUS SENSOR 12 IRIS METER IC4303 FP-569 FLEXIBLE BOARD CN4402 ACCS_VCC D_2.8V IC2801 ZOOM SENSOR 64M SDRAM (10/20) Q2801 3.6V REG L2803 10 IC4302 16M FLASH (10/20) K14 XRST L4402 IC4401 DRV_MT_4.3V L4403 DRV_MT_5.0V L4404 DVD MECHA DRIVE (12/20) XRST_IC_4101 FB4104 DRV_MT_5.0V D_2.5V D_2.5V FB4103 A_2.5V A_2.5V L4103 L4102 DRV_A_3.9V DRV_A_3.9V 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-8 2 R4413 FB4401 DRV_MT_4.3V FLASH MEMORY (MDL4060S3C) (8GB) LENS BLOCK CN5101 ZM_SENSE_VCC IRIS_DRIVE (+) A_2.8V L2904 VCC VOUT 3 Q5101 EN7 E4 MT_5.0V CN1006 FC_SENSE_VCC D_2.8V A_2.8V D_1.2V D_2.8V FP-841 FLEXIBLE BOARD MEGA model FOCUS/ZOOM MOTOR DRIVE (3/20) A D/A CONVERTER (13/20) CCD IMAGER 2 DVD410E/DVD810/DVD810E 4 VDD 1 CE IC5102 IRIS DRIVE, HALL AMP (2/20) X1701 FB2401 IC7101 CN7101 2.9V REG (20/20) IC5302 Non MEGA model POWER (3/3) (PAGE 3-9) L5301 J21 XRST 15 IC1002 MS_PWR_ON XQUICKREC_LED XBB_RST PANEL_BL_ON A_4.6V XBB_RST 1 L7101 ZM_RST_LED, FC_RST_LED EMC_XRESET_OUT F_INTo P11 IC2101 XFLASH_RST 512M SDRAM, F_/RP E8 512M OneNAND FLASH (8/20) MT_5.0V 16 MT_5.0V STL_ADDR[8] STL_ADDR[7] POWER (1/3) (PAGE 3-7) CD-731 BOARD FM_PWR_ON FM_PWR_ON EXIO/CF_ADDR[8] AR10 A_2.8V CN1203 CAM_-7.5V POWER (1/3) (PAGE 3-7) D 1, 2 EXIO_ADDR[14] AM7 XSYS_RST XIC_4201_RESET XFLASH_RST Non MEGA model 13, 14 D_3.3V A_1.2V D_1.2V D_2.8V D_1.8V A/D CONVERTER, TIMING GENERATOR (1/20) FB1201 D5691 ACCESS L8 XRST FB4105 CN4103 LDD_AVDD FB4106 LDD_LVDD IC4101 RF PROCESS (11/20) FB4102 PDIC_VCC FB4101 FPDIC_VCC 10 6, 7 CPU (5/20 - 7/20) IC1201 ZM_RST_LED, FC_RST_LED IC1701 MEGA model FB1203 4 VCC 1 CE V_OUT 3 SHOE_ON EXIO/CF_ADDR[9] AP11 VST_C_RESET GPIO_S[11] H21 MEGA model FB1204 2.9V REG: Non MEGA model 3.4V REG: MEGA model (1/20) A_4.6V 19 CRST L1201 IC1202 SHOE_ON SE7002 PITCH SENSOR 29 51 DVD MECHANISM DECK (DDX-C2000) 3-9. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. BL-021 BOARD VC-520 BOARD (3/3) EP_8.5V CN3101 EVF_VDD L3103 EVF_STB A_4.6V A_2.8V L3102 EP_4.6V 1 18 7 12 17 CN5701 CN5702 EVF_VDD EVF_STB EP_4.6V 2 BL-022 BOARD LCD902 VDD 2 18 COLOR EVF UNIT STB 11 CN5701 CN5702 EVF_VDD EVF_STB 12 D5702 (BACKLIGHT) LCD902 D5701 (BACKLIGHT) IC3101 L3101 LCD/EVF DRIVE (16/20) 6 POFF 2 XSTBY_E 10 XSTBY_P 18 25 B PD-351 BOARD FP-573 FLEXIBLE BOARD CN3102 Q3106, Q3107 3 XCLR 7 VDD_P 25 XSTBY CN6201 VDD_P PD-352 BOARD CN6205 18 XSTBY 6 14 VDD LCD901 XSTBY 2.7 inch WIDE COLOR LCD UNIT 25 18 XSTBY 6 14 Q6203 BL_H1 - BL_H3 20 - 22 20 - 22 Q3101 - Q3104 LCD BACKLIGHT DRIVE BL_H1 - BL_H3 D6203 - D6205 (BACKLIGHT) 8 D_2.8V 23 D_2.8V Q6201, Q6202 TOUCH PANEL I/F 23 CK-191 BOARD (2/2) CN1002 (2/2) D_2.8V D_2.8V D_2.5V 10 10 D_2.8V R5802 D1005 (NIGHTSHOT) R1023, R1024 CN1003 MEGA model 16 D5801 (MS ACCESS) 10 D5801 (MS ACCESS) R5802 MS-391 BOARD D_2.8V 1 CN7301 13, 14 IC1001 CN7302 MS_VCC 9 CN7301 D_2.8V MEMORY STICK DUO 13, 14 3, 4 D_2.8V MS-392 BOARD 2.9V REG (20/20) VOUT 3 TOUCH PANEL I/F CN5801 (2/2) FP-842 FLEXIBLE BOARD PANEL_BL_ON D_2.8V CK-192 BOARD (2/2) CN5801 (2/2) XBB_RST MS_PWR_ON VSSG BL_H1 - BL_H3 Q6201, Q6202 LCD/EVF BACKLIGHT CONTROL (16/20) 2.7 inch WIDE COLOR LCD UNIT VSS D6203 - D6205 (BACKLIGHT) IC3102 4 VDD 1 CE XSTBY EP_2.8V 15 11 - 9 R3110, R3113, R3114 LCD901 VDD 17 24 EP_2.8V CN6205 CN6201 VDD_P MEGA model POWER (1/3) (PAGE 3-7) MT_5.0V COLOR EVF UNIT EVF_STB 12 EP_4.6V 2 EVF_VDD 2 MS_VCC IC7301 REMOTE COMMANDER RECEIVER CN7302 MS_VCC 9 MEMORY STICK DUO C POWER (2/3) (PAGE 3-8) CN1013 (2/2) D_2.8V Non MEGA model CONTROL KEY BLOCK (PS26100) (2/2) MEGA model RV001 T 6 W (ZOOM) D002 CAM R1018 MODE_LED_VDD Q1003 LED DRIVE QUICKREC_ LED_VDD R1006 18 D003 PHOTO 4 D004 QUICK ON XQUICKREC_LED 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 3-9E Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM Non MEGA model CD-731 BOARD (SIDE A) MEGA model LENS BLOCK 1 16 CN7101 1 FP-840 FLEXIBLE BOARD 12 MEGA model 16 1 CD-672/ CD-687 BOARD (SIDE A) FP-838 FLEXIBLE BOARD 18 28 1 27 CN1201 2 1 1 2 CN1203 15 16 12 1 2 11 2 1 CN3101 18 1 51 13 50 1 CN4103 2 1 1 8 1 13 CN1009 14 2 CONTROL KEY BLOCK (PS26100) 2 1 16 2 CN4401 9 CN1003 10 10 IC4302 (Not supplied) 13 CN101114 2 1 CN1002 1 1 2 7 CN1010 CPC (For Check) 18 IC2101 (Not supplied) CN1012 A/V R 14 CN1001 2 1 LEVEL3 VC-520 BOARD (SIDE A) 21 17 CN1008 14 2 5 CN1005 FP-841 FLEXIBLE BOARD CN1006 6 24 CN1013 8 30 7 29 2 23 1 CN3102 1 CN5101 FLASH MEMORY (MDL4060S3C) (8GB) 2 2 14 1 1 CN4402 LCD902 WIDE COLOR EVF UNIT 2 1 LCD902 COLOR EVF UNIT DVD410E/DVD810/DVD810E 24 MIC901 MICROPHONE UNIT 23 8 FP-569 FLEXIBLE BOARD MEGA model 28 FLEXIBLE FLAT CABLE (FFC-133) 1 FLEXIBLE FLAT CABLE (FFC-140) M903 MOTOR UNIT (GEARD MOTOR) Non MEGA model 1 28 M 17 CN5701 2 1 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E 1 LENS BLOCK BL-021 BOARD (SIDE A) : Non MEGA model BL-022 BOARD (SIDE A) : MEGA model 20 28 CN5702 CN7001 2 1 CN901 HOT SHOE 15 1 CPC (For Check) IC4901 (Not supplied) J001 DC IN 30 FLEXIBLE FLAT CABLE (FFC-089) CN1004 USB C HARNESS (HN-024) (Gray) HARNESS (HN-024) (Gray) SP901 SPEAKER LEVEL3 VC-520 BOARD (SIDE B) BH001 BATTERY TERMINAL BT901 LITHIUM BATTERY DVD MECHANISM DECK (DDX-C2000) 1 1 24 10 30 1 FP-573 FLEXIBLE BOARD CN5801 FP-839 FLEXIBLE BOARD 1 CK-191 BOARD (SIDE B): Non MEGA model CK-192 BOARD (SIDE B): MEGA model MS-391 BOARD (SIDE A): Non MEGA model MS-392 BOARD (SIDE A): MEGA model 1 30 12 10 16 1 PD-351 BOARD (SIDE A): Non MEGA model PD-352 BOARD (SIDE A): MEGA model CN7302 MEMORY STICK CONNECTOR FP-842 FLEXIBLE BOARD 1 6 1 RV-011 BOARD : Non MEGA model RV-012 BOARD : MEGA model CN6202 CN6201 11 HARNESS (HN-024) (Gray) HARNESS (HN-024) (Gray) 1 24 CN6205 2.7 INCH WIDE COLOR LCD UNIT 05 1 6 16 1 CN6204 TOUCH PANEL 1 16 CN7301 CONTROL SWITCH BLOCK (SB22100) LCD901 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-1 FRAME 4-2. SCHEMATIC DIAGRAMS Link CD-672/CD-687 BOARD: MEGA model (CCD IMAGER) CK-192 BOARD: MEGA model (CONTROL SWITCH) FP-838 FLEXIBLE BOARD: MEGA model (VC-CD CONNECTION) MS-391 BOARD: Non MEGA model (MS CONNECTOR) MS-392 BOARD: MEGA model (MS CONNECTOR, REMOTE COMMANDER RECEIVER) FP-841 FLEXIBLE BOARD: DVD410E/ DVD810/DVD810E (FLASH MEMORY) FP-842 FLEXIBLE BOARD (VC-MS CONNECTION) CD-731 BOARD: Non MEGA model (CCD IMAGER) BL-021 BOARD: Non MEGA model (EVF, EVF BACKLIGHT) BL-022 BOARD: MEGA model (EVF, EVF BACKLIGHT) PD-351 BOARD: Non MEGA model (LCD, LCD BACKLIGHT) PD-352 BOARD: MEGA model (LCD, LCD BACKLIGHT) FP-573 FLEXIBLE BOARD (VC-PD CONNECTION) FP-569 FLEXIBLE BOARD (EJECT SWITCH/MOTOR) FP-840 FLEXIBLE BOARD (HOT SHOE) RV-011: Non MEGA model (PANEL REVERSE DETECT) RV-012: MEGA model (PANEL REVERSE DETECT) CONTROL SWITCH BLOCK (SB22100) FP-839 FLEXIBLE BOARD (DC IN) CONTROL KEY BLOCK (PS26100) CK-191 BOARD: Non MEGA model (CONTROL SWITCH) COMMON NOTE FOR SCHEMATIC DIAGRAMS Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVE610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 ENGLISH 4-2. SCHEMATIC DIAGRAMS JAPANESE 4-2. SCHEMATIC DIAGRAMS (ENGLISH) THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 1. Connection Pattern box Color bar chart For PTB-450: J-6020-250-A Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-1450: J-6082-559-A L = 1 m (PTB-450) L = 40 cm (PTB-1450) Pattern box Front of the lens L Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– Line • J : IN/OUT direction of (+,–) B LINE. • C: adjustment for repair. (Measuring conditions voltage and waveform) • Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Camera A B A=B Red Blue White Magenta H Cyan Green Yellow 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. B A Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame Fig.b (Picture on monitor TV) Precautions for Replacement of Imager • If the imager has been replaced, carry out all the adjustments for the camera section. • As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-2 ENGLISH 4-2. SCHEMATIC DIAGRAMS JAPANESE (JAPANESE) 回路図共通ノート (他に必要なノートは各ブロックに記載してあります) 【回路図ノート】 1. 接続図 ・ケミコン,タンタルを除くコンデンサで,耐圧50V以下のもの はその耐圧を省略。単位はすべてμF(pはpF)。 ・チップ抵抗で指示のないものは,1/10W以下。 kΩ=1000Ω,MΩ=1000kΩ ・チップ部品交換時の注意 取り外した部品は再使用せず,未使用の部品をご使用くださ い。 タンタルコンデンサのマイナス側は熱に弱いため注意してくだ さい。 ・チップ部品には下記のように表示したものがあります。 例 C 541 L 452 22U 10UH TA A 2520 ↑ ↑ ↑ 種類 ケースサイズ 外形寸法(mm) ・抵抗,コンデンサ,ICなど定数にXXがあるものは,使用して いない事を示しています。このため,使用していない回路が記 載されている事があります。 ・★印のある部品は,機種などにより異なりますので機能別マウ ント一覧表を参照してください。 ・可変抵抗と半固定抵抗で,B特性の表示を省略。 ・信号名表記について,下記のような場合があります。 XEDIT → EDIT PB/XREC → PB/REC ・2は不燃性抵抗。 ・1はヒューズ抵抗。 ・Cはパネル表示名称。 ・AはB+ライン。 ・BはB−ライン。 ・JはBライン(+,−)の入出力方向を示す。 ・Cは調整名称。 パターンボックス カラーバーチャート For PTB-450: J-6020-250-A Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-1450: J-6082-559-A L = 1 m (PTB-450) L = 40 cm (PTB-1450) パターンボックス レンズ前面 L カメラ 2. 図a及び図bの波形が得られるように画枠調整して下さい。 H シ 黄 ア ン A B マ ゼ 白 ン 緑 ダ 赤 A=B 青 B A 図a(映像入出力端子出力波形) 電子ビーム走査線 【電圧・波形測定条件ノート】 ・電圧値及び信号波形はパターンボックスのカラーバーチャート を被写体としたときの測定点対アース間の参考値。 (デジタルマルチメータ;入力インピーダンス DC10MΩ使 用) ・使用テスタの入力インピーダンスにより電圧値が多少異なりま す。 ブラウン管の画像枠 図b(テレビモニタの映像) イメージャ交換時の注意 ・イメージャを交換した場合は,カメラ部の全調整を 行ってください。 ・イメージャは構造上,静電気により破壊される恐れが あるため,MOS ICと同様に注意して取り扱ってくだ さい。 また,受光部にはゴミの付着,および強い光がはいる ことのないように注意してください。 0印の部品,または0印付きの点線で囲まれた部品は, 安全性を維持するために重要な部品です。 従って交換時は,必ず指定の部品を使用して下さい。 お願い 図面番号で部品を指定するときは基板名又はブロック を併せて指定して下さい。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-3 2 1 3 4 6 5 7 8 A A Note: IC7002 is supplied including in CCD block assy. Note: Voltages of IC7002 can not be measured, because this is mounted by the side of the lens. R10.8/P0.1 Q7001 UNR32A300LS0 SWITCH 0 SE7002 PITCH SENSOR C7030 XX 2 4 1 3 R7014 1M 1.3 1.3 R7.7/P0.1 1.3 1.3 1.3 C7016 0.1u 1.3 4 B 1.3 V5 3 2.8 R7013 10k C7026 0.047u 0.9 V4 Vref R7005 1k OUT V3 R7006 12k IC7002 ICX617AKF-J CCD IMAGER C7028 10u C7024 10u R7017 XX 1 GND V2 2 C7005 0.1u Vcc V1 V6 VL 1 RCSUB N.C GND 2 N.C 3 SUB 4 H1 5 N.C 6 H2 7 N.C 8 RG 9 V_OUT 10 N.C B VDD 1.3 0.7 R7004 10k IDRV R7011 XX C7006 1u C7007 4.7u L7001 10uH 3 2 1 GND LIB2 LIA1 LO1 HI1 HO1 Vref1 AM1 OUT1 PASS LIA2 LO2 HI2 AM2 OUT2 CRST VCC C7023 4.7u IC7003 NJM3230V(TE2) PITCH/YAW SENSOR AMP 2 4 3 C 2.8 0 1.3 1.3 1.3 11 12 13 14 15 16 17 18 19 20 1.3 C7018 0.1u Vref2 4 HO2 5 1.5 6 C7014 XX C7013 XX 6 1.3 C7008 XX CD-672 2.8 2 1 1 Vref VCC OUT C7027 0.047u C7025 10u C7029 10u OUT GND R7007 XX R7008 XX 5 1 ISF 2 R7009 XX IN 3 C 7 2 4 6 8 R7019 XX R7020 XX C7012 XX R7010 XX R7012 XX 8 1.5 IC7001 XX R7001 XX 1 3 5 7 9 GND C7002 0.1u 4 C7003 0.1u R7018 XX C7001 XX 10 1 R7002 1200 C7017 0.1u 0.8 R7/P0 Q7002 2SC5096-O/R(TE85L) CLAMP Vcc R12.1/P0.1 C7004 XX RB7001 22k LIB2 11 12 13 14 15 16 17 18 19 20 3 4 C7015 0.1u R7015 1M R7016 10k 1.3 SE7001 YAW SENSOR L7002 10uH C7009 XX D D C7010 0.1u CD-672 2 3 4 5 6 7 8 1 E SE_2.8V YAW_AD VST_C_RESET PITCH_AD SE_GND SUB RCSUB 9 V6 GND 11 12 13 14 10 V5 V4 V3 V2 V1 15 GND 16 GND 17 H1 18 GND 19 H2 20 GND 21 RG 22 GND 24 25 26 27 28 23 GND CAM_-7.5V CAM_15V GND CCD_OUT+ GND CN7001 E 28P FB7001 C7011 10u MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E Note: CD-672 complete board is supplied instead of CD-687 complete board, because CD-672 complete board and CD-687 complete board are compatible. CD-672/CD-687 BOARD : MEGA model FP-838 FLEXIBLE Page 4-5 of Level 2 CCD IMAGER F F XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-4 CD-672/CD-687 2 V6 1 YAW_AD SE_2.8V SE_2.8V 1PIN H2 H1 VL SUB NC RG VDD R7103 XX RCSUB 16 VST_C_RESET YAW_AD 15 PITCH_AD VST_C_RESET CCD_OUT SE_GND PITCH_AD REG_GND SUB GND 14 RCSUB SUB REG_GND RCSUB B C Note: Voltages of IC7101 can not be measured, because this is mounted by side of the lens. 13 GND C7108 0.1u B 12 GND C7106 XX Note: IC7101 is not included in CD-731 complete board. C RG V6 V6 C VSHT V5 11 V4 V5 10 V3 V4 H1 V2 V3 REG_GND V2 CN1201 Page 4-6 of Level 3 9 V1 R8/P0 C7101 10u 16V H2 GND V1 Q7101 2SC3931G0LS0 BUFFER C7104 10u 16V VC-520 (1/20) 8 GND R12/ P0 C7103 0.01u B B 7 GND 9 V1 H1 GND 10 V2 GND H1 11 6 H2 GND 12 V3 GND H2 13 5 RG GND 14 4 RG B R7101 3300 15 V4 GND GND C7105 15p CH R8.8/P0 16 V5 GND GND A 8 L7101 10uH CAM_-7.5V 7 R7102 XX CAM_15V CAM_-7.5V 3 GND CAM_15V 2 C GND V6 CN7001 Page 4-4 of Level 2 CCD_OUT+ 1 CD-672/CD-687 GND CCD_OUT+ 6 IC7101 ICX650NKF-H : NTSC ICX651NKF-H : PAL CCD IMAGER 1PIN GND 5 CAM_-7.5V B 4 CAM_12.0V 28PIN 3 VOUT A GND A V1 A 4 3 2 V2 1 V3 4 3 V4 2 V5 1 28PIN D D D D CN7101 16P VC-520 (1/20) MEGA model:DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CN1203 Through the Flexible Flat Cable (FFC-133) Page 4-6 of Level 3 E E E E Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E CD-731 BOARD : Non MEGA model CCD IMAGER FP-838 FLEXIBLE BOARD : MEGA model F VC-CD CONNECTION F F (PRINTED WIRING BOARD is omitted.) XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE F 05 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-5 FP-838, CD-731 Schematic diagrams of the VC-520 board are not shown. Pages from 4-6 to 4-25 are not shown. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4 3 2 1 A A R5701 XX CN5701 B C 1 EP_4.6V 2 A A NESW007AT-T099 D5702 (BACKLIGHT) CN5701 18P LED_K B 21 4 3 2 1 B COM 18P LED_K 1 EP_4.6V 2 EVF_COM 3 EVF_PSIG 4 EVF_VG 5 EVF_VR 6 R5701 XX D5701 NESW007AT-T099 (BACKLIGHT) EVF_COM EVF_PSIG EVF_VG EVF_VR EVF_VB 21 EVF_COM 20 EVF_PSIG 19 EVF_VG 18 EVF_VR 17 EVF_VB 16 EVF_PCG 15 EVF_EN 14 EVF_VCK 13 EVF_VST 12 EVF_STB 11 EVF_REF EVF_COM 3 20 PSIG EVF_VB 7 EVF_PSIG 4 19 CS EVF_PCG 8 EVF_VG 5 18 VG EVF_EN 9 EVF_VR 6 17 VR EVF_VCK 10 EVF_VB 7 16 VB EVF_VST 11 EVF_PCG 8 15 PCG EVF_STB 12 EVF_EN 9 14 EN EVF_REF 13 EVF_VCK 10 13 VCK EVF_GND 14 10 EVF_DWN EVF_VST 11 12 VST EVF_HCK1 15 9 EVF_NRW EVF_STB 12 11 STB EVF_HCK2 16 8 EVF_RGT EVF_REF 13 10 REF EVF_HST 17 7 EVF_HCK1 EVF_GND 14 9 WIDE EVF_VDD 18 6 EVF_HCK2 EVF_HCK1 15 8 RGT 5 EVF_HST EVF_HCK2 16 7 HCK1 4 VSSG 3 VSS 2 EVF_VDD 1 N.C. 17 6 HCK2 EVF_VDD 18 5 HST 4 VSSG 3 VSS 2 VDD 1 N.C. C5701 0.1u B CN3101 Through the Flexible Flat Cable (FFC-140) C5702 1u B R5702 1M C5703 XX D5701 EDZ-TE61-5.6B Page 4-21 of Level 3 CN5702 VC-520 (16/20) CN3101 Through the Flexible Flat Cable (FFC-140) EVF_VCK EVF_VST EVF_STBY EVF_REF EVF_HCK1 EVF_HCK2 C5701 0.1u B C5702 1u B D5702 C5703 XX EDZ-TE61-5.6B CN5702 C 21P Page 4-21 of Level 3 21P LCD902 COLOR EVF UNIT D C EVF_EN EVF_HST EVF_HST VC-520 (16/20) C EVF_PCG B D LCD902 WIDE COLOR EVF UNIT D D MEGA model:DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E Non MEGA model:DCR-DVD110E/DVD115E/DVD610/DVD610E Note: LCD902 is not included in BL-022 complete board. Note: LCD902 is not included in BL-021 complete board. E F BL-021 BOARD : Non MEGA model EVF, EVF BACKLIGHT E E F F XX MARK:NO MOUNT E BL-022 BOARD : MEGA model EVF, EVF BACKLIGHT F XX MARK:NO MOUNT 05 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-26 BL-021, BL-022 1 2 4 3 5 7 6 8 10 9 11 12 Note: LCD901 is not included in PD-351 complete board. A COM_P PANEL_VR PANEL_VG 28 REG_GND 27 REG_GND 26 VDD_P 25 EP_2.8V 24 D_2.8V 23 BL_H3 22 BL_H2 21 BL_H1 20 REG_GND 19 KEY_AD0 18 TP_X 17 TP_SEL1 16 FP-573 FLEXIBLE TP_Y 15 REF 14 LND001-LND030 Page 4-29 of Level 2 29 PANEL_VB B PANEL_NOR/REV 12 HCK2 11 HST 10 C EN PSIG CN6201 VG_P VST_P VB_P VCK_P EN_P DWN_P R6207 XX R6215 XX R6231 XX R6230 XX R6214 XX XSTBY_P XX R6229 XX CL6202 CL6201 6 5 4 VST 3 VCK 2 COM 1 Q6203 XX CL6203 REF_P C6206 0.1u B HCK2_P REF_P R6232 XX HCK1_P VP_P HCK1_P HCK2_P HST_P PCG_P D6203 NSSW008CT-P1-T177 VD6205 XX D6204 NSSW008CT-P1-T177 VD6206 XX D6205 NSSW008CT-P1-T177 VD6207 XX VG_P VR_P VB_P RGT_P COM_P EN_P VP_P 7 RGT R6209 1M HST_P 8 DWN C6205 1u B PCG_P 9 XSTBY D6202 EDZ-TE61-5.6B C6204 13 HCK1 PCG VR_P 30 XX D6203-D6205 (BACKLIGHT) XSTBY_P R6233 24 COM 23 CS 22 VST 21 VCK 20 EN 19 DWN 18 VDD 17 VSS 16 N.C. 15 VSSG 14 XSTBY 13 PCG 12 HST 11 REF 10 TEST1 9 TEST2 8 HCK2 7 HCK1 6 PSIG 5 G 4 R 3 B 2 RGT 1 COM CN6205 LCD901 (1/2) 2.7inch WIDE COLOR LCD UNIT A B with TOUCH PANEL C 24P DWN_P RGT_P VST_P VCK_P CL6204 COM_P 30P D6210 XX 2 1 3 RV-011 LN7601, LN7602 D Through the Harness (HN-024) ×2 LN6202 NOR_REV LN6203 REG_GND C6201 XX D Page 4-33 of Level 2 6P 2ND_SS_SW 3 LND001-LND006 2ND_ZOOM(T) 4 Page 4-34 of Level 2 2ND_ZOOM(W) 5 HOME_SW 6 R6202 R6201 2200 1500 1200 E XX D6201 E R6203 4 2 5 1 N.C 2 3 REG_GND 1 CN6202 CONTROL SWITCH BLOCK (SB22100) F F with LCD UNIT CN6204 TP_R 1 TP_L 2 N.C. 3 TP_BOT 4 TP_TOP 5 N.C. 6 VD6201 XX VD6202 XX 0.0047u C6202 B VD6203 XX VD6204 XX 2.8 B 0.0047u C6203 5 LCD901 (2/2) TOUCH PANEL 6P 2.8 0 1 6 2.8 LN6201 2 6 3 0 PD-351 BOARD : Non MEGA model 2.8 5 1 4 2.8 Q6201 XP421F-TXE R6226 XX 2 Q6202 XP411F-TXE Q6201, Q6202 TOUCH PANEL I/F G 3 4 G Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E 0 LCD, LCD BACKLIGHT XX MARK:NO MOUNT NO MARK:REC/PB MODE CH_GND H H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-27 PD-351 1 2 4 3 5 7 6 8 10 9 11 12 Note: LCD901 is not included in PD-352 complete board. A COM_P 24 COM 23 CS 22 VST 21 VCK 20 EN 19 DWN 18 VDD 17 VSS 16 N.C. 15 VSSG 14 XSTBY 13 PCG 12 HST 11 REF 10 TEST1 A VR_P PANEL_VR PANEL_VG 29 PANEL_VB 28 REG_GND 27 REG_GND 25 EP_2.8V 24 D_2.8V 23 BL_H3 22 BL_H2 21 BL_H1 20 REG_GND 19 KEY_AD0 18 TP_X 17 TP_SEL1 16 TP_Y 15 REF 14 LND001-LND030 Page 4-29 of Level 2 13 HCK1 12 HCK2 11 PCG C VB_P VCK_P EN_P DWN_P D6202 C6204 R6215 XX R6231 XX R6230 1u B R6214 XX XSTBY_P XX 8 7 XSTBY 6 DWN 5 RGT 4 VST 3 VCK 2 COM 1 CL6202 CL6201 0 Q6203 2SA2078G0LSO SWITCH C6205 1u B R6209 1M -5.5 CL6203 REF_P C6206 0.1u B HCK2_P R6232 xx HCK1_P REF_P VP_P HCK1_P HCK2_P HST_P PCG_P 9 EN R6207 120k HST_P 10 PSIG EDZ-TE61-5.6B PCG_P D6203 NSSW008CT-P1-T177 VD6205 XX D6204 NSSW008CT-P1-T177 VD6206 XX D6205 NSSW008CT-P1-T177 VD6207 XX VG_P VR_P VB_P RGT_P COM_P EN_P D6203-D6205 (BACKLIGHT) VP_P R6233 XX 9 N.C. 8 HCK2 7 HCK1 6 PSIG 5 G 4 R 3 B 2 RGT 1 COM CN6205 LCD901 (1/2) 2.7inch WIDE COLOR LCD UNIT B with TOUCH PANEL C 24P XSTBY_P DWN_P RGT_P VST_P VCK_P CL6204 COM_P 30P CN6201 VST_P R6229 XX PANEL_NOR/REV HST VG_P 26 VDD_P B FP-573 FLEXIBLE 30 D6210 XX 2 1 3 RV-012 D LN7601, LN7602 LN6202 NOR_REV Through the Harness (HN-024) ×2 LN6203 REG_GND C6201 XX D Page 4-33 of Level 2 6P 2ND_SS_SW 3 2ND_ZOOM(T) 4 2ND_ZOOM(W) 5 HOME_SW 6 R6202 R6201 2200 1500 1200 E XX D6201 E R6203 4 2 5 1 N.C 2 3 LND001-LND006 Page 4-34 of Level 2 REG_GND 1 CN6202 CONTROL SWITCH BLOCK (SB22100) F F TP_R 1 TP_L 2 N.C. 3 TP_BOT 4 TP_TOP 5 N.C. 6 LCD901 (2/2) TOUCH PANEL with LCD UNIT VD6201 XX VD6202 XX 0.0047u C6202 B VD6203 XX VD6204 XX 2.8 CN6204 5 B 0.0047u C6203 6P 2.8 0 1 6 2.8 LN6201 6 3 2 1 4 2.8 0 2.8 5 R6226 XX 2 Q6202 XP411F-TXE Q6201, Q6202 TOUCH PANEL I/F Q6201 XP421F-TXE G 3 4 G 0 MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CH_GND H PD-352 BOARD : MEGA model H LCD, LCD BACKLIGHT XX MARK:NO MOUNT NO MARK:REC/PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-28 PD-352 2 1 3 PANEL_VR PANEL_VR LND001 LND032 PANEL_VG PANEL_VG LND002 LND033 PANEL_VB PANEL_VB LND003 LND034 REG_GND REG_GND LND004 LND035 REG_GND REG_GND LND005 LND036 VDD_P VDD_P LND006 LND037 EP_2.8V EP_2.8V LND007 LND038 D_2.8V D_2.8V LND008 LND039 BL_H3 BL_H3 LND009 LND040 BL_H2 BL_H2 LND010 LND041 BL_H1 BL_H1 LND011 LND042 REG_GND REG_GND LND012 LND043 KEY_AD0 KEY_AD0 LND013 TP_X LND014 TP_SEL1 LND015 TP_Y LND016 REF LND017 PANEL_NOR/REV LND018 LND044 TP_X LND045 TP_SEL1 LND046 TP_Y LND047 C REF PANEL_NOR/REV LND049 HCK1 HCK1 LND019 LND050 HCK2 HCK2 LND020 LND051 HST HST LND021 LND052 PCG PCG LND022 LND053 EN EN LND023 PSIG LND024 XSTBY LND025 LND054 PSIG LND055 XSTBY LND056 DWN DWN LND026 LND057 RGT RGT LND027 LND058 VST VST LND028 LND059 VCK VCK LND029 LND060 COM COM LND030 30PIN D Non MEGA model PD-351 CN3102 CN6201 Page 4-21 of Level 3 Page 4-27 of Level 2 S5693 C 1 2 4 A C 1 3 8 EJECT_DET 4 3 4 3 7 REG_GND VC-520 (12/20) 6 LID_OPEN S5691 OPEN 2 4 5 XEJECT_SW 4 C 1 REG_GND(D_MT_GND) 3 EJECT_DRV CN4402 Page 4-17 of Level 3 2 ACCS_VCC 3 1 ACCS_LED LND001 B B B GND M903 MOTOR UNIT (GEARD MOTOR) M LND002 DRV D5691 SML-512UWT86 ACCESS Note: M903 is not included in FP-569 flexible complete board. C FP-569 FLEXIBLE BOARD C C EJECT SWITCH/MOTOR 05 1 2 3 4 Note: CN901 (HOT SHOE) is not included in FP-840 flexible board. 16PIN GND A D MEGA model PD-352 CN6201 Page 4-28 of Level 2 CN901 HOT SHOE Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E E 4 S5694 (EJECT DETECT) 2 S5692 C 1 2 1PIN VC-520 (16/20) 3 S5692, S5693 (LID OPEN DETECT) 30PIN 1PIN LND031 LND048 2 A A A B 1 4 B E A USB- 12PIN USB+ GND SHOE_CONT SHOE_CONT LANC LANC STROBE STROBE ID2 ID2 UNREG UNREG CN1008 UNREG UNREG Page 4-25 of Level 3 ID1 ID1 MIC_RL MIC_GND MIC_RR MIC_FL MIC_GND MIC_FR MIC_FL GND MIC_FR 1PIN VC-520 (20/20) B GND 1PIN MEGA model:DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E FP-573 FLEXIBLE BOARD F VC-PD CONNECTION C F FP-840 FLEXIBLE BOARD : MEGA model C HOT SHOE (PRINTED WIRING BOARD is omitted.) (PRINTED WIRING BOARD is omitted.) 05 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-29 FP-573, FP-569, FP-840 • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 3 2 1 4 6 5 7 8 LN5801 Harness(HN-024)(Gray) SP+ A LN5802 A SP901 SPEAKER Harness(HN-024)(Gray) SP- Note: BT901 (lithium battery) and SP901 are not included in CK-191 complete board. B BH5801 (BATTERY HOLDER) VD5804 VD5802 BT901 (LITHIUM BATTERY) REG_GND 1 SP+ 2 SP- 3 REG_GND 4 KEY_AD3 5 XBATT_VIEW 6 BATT_LI_3V 7 HI_XRESET ACCCESS_LED D_2.8V 3 VD5805 XX R5801 XX C 8 9 10 VC-520 (20/20) 3 3 CN1002 Through the Flexible Flat Cable (FFC-089) 1 S5802 4 3 1 VD5807 XX C 2 1 VD5806 XX 10P VD5803 XX CN5801 B XX XX 1 S5803 XX S5806 N 4 DISP/ BATT INFO 2 4 2 2 Page 4-25 of Level 3 2 D VD5801 XX 1 3 D 4 S5801 RESET CHASSIS_GND R5802 D5801 LN5803 220 CL-196HR-CD-T (MS ACCESS) E E Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E CK-191 BOARD : Non MEGA model CONTROL SWITCH F F XX MARK:NO MOUNT 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-30 CK-191 • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 3 2 1 4 6 5 7 8 LN5801 Harness(HN-024)(Gray) SP+ A LN5802 A SP901 SPEAKER Harness(HN-024)(Gray) SP- Note: BT901 (lithium battery) and SP901 are not included in CK-192 complete board. B BH5801 (BATTERY HOLDER) VD5804 VD5802 BT901 (LITHIUM BATTERY) REG_GND 1 SP+ 2 SP- 3 REG_GND 4 KEY_AD3 5 XBATT_VIEW 6 BATT_LI_3V 7 HI_XRESET ACCCESS_LED D_2.8V 3 VD5805 XX DVD410E/DVD810/DVD810E R5801 1200 C 8 9 10 VC-520 (20/20) 3 3 CN1002 Through the Flexible Flat Cable (FFC-089) 1 S5802 4 1 VD5807 XX C 2 1 VD5806 XX 10P VD5803 XX CN5801 B XX XX 3 1 S5803 S5806 DUBBING N 4 DISP/ BATT INFO 2 4 2 2 Page 4-25 of Level 3 2 D VD5801 XX 1 3 D 4 S5801 RESET CHASSIS_GND R5802 D5801 LN5803 220 CL-196HR-CD-T (MS ACCESS) E E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CK-192 BOARD : MEGA model CONTROL SWITCH F F XX MARK:NO MOUNT 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-31 CK-192 MSDATA3 11 XMS_IN 10 MSDATA2 9 MSDATA0 8 MSDATA1 7 MS_BS 6 REG_GND 5 REG_GND 4 SIRCS_SIG 3 PANEL_O/C 2 D_2.8V 1 XX XX R7306 FB7301 120 FB7302 R7307 R7303 120 120 R7304 XX C7302 XX MS_VCC 14 MS_VCC 13 MS_SCLK MS_SCLK 12 7 MSDATA3 MSDATA3 11 6 XMS_IN XMS_IN 10 5 MSDATA2 MSDATA2 9 10 VSS 9 VCC 8 120 R7302 FB7303 FB7304 R7308 XX S7301 PANEL OPEN/CLOSE MEMORY STICK DUO B B 4 MSDATA0 MSDATA0 3 MSDATA1 MSDATA1 7 2 MSBS MS_BS 6 1 VSS REG_GND 5 CN7302 10P R7310 XX 16P CN7301 VD7301 XX FP-842 FLEXIBLE IC7301 XX C Page 4-33 of Level 2 OUT VCC GND 15 C7301 XX C REG_GND LN7302 8 REG_GND 4 SIRCS_SIG 3 PANEL_O/C 2 D_2.8V 1 16P FP-842 FLEXIBLE Page 4-33 of Level 2 R7301 R7305 XX XX R7306 FB7301 FB7302 R7307 FB7303 FB7304 R7303 120 120 R7304 R7308 XX C7302 XX 10 VSS 9 VCC 8 MS_SCLK 7 MSDATA3 6 XMS_IN 5 MSDATA2 4 MSDATA0 3 MSDATA1 120 R7302 120 REG_GND LN7301 XX S7301 PANEL OPEN/CLOSE 2 MSBS 1 VSS CN7302 MEMORY STICK DUO B 10P R7310 XX IC7301 RS-450-T REMOTE COMMANDER RECEIVER VD7301 XX C 2.8 OUT 3 12 R7305 LN7301 REG_GND 2.8 VCC 2 MS_SCLK R7301 16 REG_GND GND 1 13 REG_GND REG_GND 12 14 MS_VCC A 11 MS_VCC C7301 XX 3 15 2 CN7301 16 REG_GND 1 B C A A REG_GND 4 12 A 3 2 1 4 11 3 2 1 LN7302 REG_GND REG_GND LN7303 LN7303 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E D D D D E E E E MS-391 BOARD : Non MEGA model MS-392 BOARD : MEGA model MS CONNECTOR MS CONNECTOR, REMOTE COMMANDER RECEIVER XX MARK:NO MOUNT F F F 05 XX MARK:NO MOUNT NO MARK:REC/PB MODE F 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-32 MS-391, MS-392 1 2 3 1 4 A VCC VCC VCC VCC REG_GND REG_GND SCLK SCLK REG_GND REG_GND S7601 (PANEL REVERSE) 2 1 DATA3 INS INS DATA2 DATA2 REG_GND REG_GND SDIO/DATA0 SDIO/DATA0 REG_GND REG_GND DATA1 DATA1 BS BS REG_GND REG_GND CN1006 Page 4-25 of Level 3 LN6202, LN6203 Through the Harness (HN-024) ×2 Page 4-27 of Level 2 B B 3 B Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E BOARD : DVD410E/DVD810/DVD810E C C C RV-011 BOARD: Non MEGA model PANEL REVERSE DETECT (PRINTED WIRING BOARD is omitted.) 05 05 1 2 3 D_2.8V PANEL_O/C PANEL_O/C SIRCS_SIG SIRCS_SIG REG_GND REG_GND REG_GND REG_GND MS_BS MS_BS MSDATA1 MSDATA1 MSDATA0 MSDATA0 MSDATA2 MSDATA2 XMS_IN XMS_IN MSDATA3 MSDATA3 MS_SCLK MS_SCLK MS_VCC MS_VCC MS_VCC MS_VCC REG_GND REG_GND REG_GND REG_GND 16Pin 4 3 A A A S7601 (PANEL REVERSE) 2 1 PD-352 LN6202, LN6203 Through the Harness (HN-024) ×2 B B Page 4-28 of Level 2 REG_GND LN7601 4 3 B NOR_REV LN7602 1Pin Non MEGA model MS-391 VC-520 (20/20) MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CN1003 Page 4-25 of Level 3 CN7301 Page 4-32 of Level 2 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CN7301 Page 4-32 of Level 2 C 2 16Pin D_2.8V MEGA model MS-392 1 4 1Pin B 4 NOR_REV FLASH MEMORY A LN7601 LN7602 1pin FP-841 FLEXIBLE REG_GND PD-351 VC-520 (20/20) DATA3 14pin C A 14pin 1pin B 4 3 A A FLASH MEMORY (MDL4060S3C) (8GB) 2 FP-842 FLEXIBLE BOARD C C C RV-012 BOARD: MEGA model VC-MS CONNECTION PANEL REVERSE DETECT (PRINTED WIRING BOARD is omitted.) 05 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-33 FP-841, FP-842, RV-011, RV-012 • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 1 2 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E A 4 3 2 1 4 3 A A A EASY S006 S004 R001 6.1k HOME BACK LIGHT S005 R002 2.7k QUICK ON S003 S004 W Non MEGA model PD-351 6P (ZOOM) B LND001 HOME_SW S002 T 2ND_ZOOM(W) LND002 2ND_ZOOM(T) LND003 2ND_SS_SW LND004 N.C LND005 REG_GND LND006 S001 1P R003 10k B B CN6202 Page 4-27 of Level 2 D004 B SML-512WWT86 QUICK ON MEGA model PD-352 1 CN6202 Page 4-28 of Level 2 REG_GND PHOTO KEY_AD2 D_2.8V QUICKREC_LED_VDD S002 PHOTO FREEZE W T (ZOOM)t T REG_GND ZOOM_VR_AD KEY_AD1 R005 10k POWER S003 PHOTO REC CONTROL SWITCH BLOCK (SB22100) C C MODE S003 REG_GND D_2.8V C ON t R004 2.7k D_2.8V OFF (CHG) S002 t START/STOP RV001 XPOWER_SW XPOWER_SW XMODE_SW XMODE_SW REG_GND C START/STOP S/S CONTROL SWITCH BLOCK (SB22100) is replaced as block, so that PRINTED WIRING BOARD is omitted. S001 CHARGE_LED_VDD XCHARGE_LED XCAM_LED 05 XPHOTO_LED 28 1 2 3 VC-520 (20/20) D Note: BH001 and J001 are not included in FP-839 flexible board. A BATT_GND CHG MODE_LED_VDD 4 24pin D001 SML-512WWT86 CN1013 Page 4-25 of Level 3 D002 SML-412MWT86 CAM D PHOTO D003 SML-412MWT86 A BATT_GND BATT_GND BATT_GND 4 BH001 BATTERY TERMINAL C BATT_GND BATT_SIG 2 N.C 1 BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG B BATT_XEXT ACV_UNREG VC-520 (20/20) CN1001 Page 4-25 of Level 3 E B E ACV_UNREG ACV_UNREG ACV_UNREG ACV_UNREG N.C J001 DC IN 2 HOT 3 SW ACV_GND 1 COLD ACV_GND CONTROL KEY BLOCK (PS26100) ACV_GND ACV_GND ACV_GND C F 1Pin CONTROL KEY BLOCK (PS26100) is replaced as block, so that PRINTED WIRING BOARD is omitted. F C FP-839 FLEXIBLE BOARD 05 DC IN 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-34 SB22100, FP-839, PS26100 4-3. PRINTED WIRING BOARDS Link CD-672/CD-687 BOARD: MEGA model RV-012 BOARD: MEGA model CD-731 BOARD: Non MEGA model PD-352 BOARD (SIDE A): MEGA model FP-569 FLEXIBLE BOARD PD-352 BOARD (SIDE B): MEGA model BL-021 BOARD: Non MEGA model CK-191 BOARD: Non MEGA model BL-022 BOARD: MEGA model CK-192 BOARD: MEGA model RV-011 BOARD: Non MEGA model MS-391 BOARD: Non MEGA model PD-351 BOARD (SIDE A): Non MEGA model MS-392 BOARD: MEGA model PD-351 BOARD (SIDE B): Non MEGA model FP-839 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVE610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS (ENGLISH) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • Chip parts. Transistor • • : Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation B (JAPANESE) プリント図共通ノート 【プリント図ノート】 ・ ・ :無鉛半田を使用しています。 :基板 :フレキシブル配線板 見ている面側のパターン。 :裏側のパターン (他のパターンについては表示されていません) ・スルーホールは省略。 ・プリント図には,本機で使用していない部品が記載されている 場合があります。 ・Cはパネル表示名称。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-35 Diode 6 5 4 4 5 6 5 C E 4 4 3 5 3 3 1 23 1 2 3 3 2 1 1 2 3 3 2 1 2 1 2 1 2 1 4 3 3 4 6 5 4 4 5 6 2 1 1 2 3 3 2 1 2 2 1 3 2 5 4 3 3 4 5 4 1 1 2 3 2 4 1 1 6 54 CD-672/CD-687 (4 layers): MEGA model, CD-731 (2 layers): Non MEGA model : Uses unleaded solder. MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E, Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E CD-672/CD-687 BOARD (SIDE A) CD-672/CD-687 BOARD (SIDE B) (MEGA model) (MEGA model) 3 8 7 C7015 R7020 1 C7018 C7016 Note: CD-672 complete board is supplied instead of CD-687 complete board, because CD-672 complete board and CD-687 complete board are compatible. R7019 L7002 SE7001 (YAW) 2 Note: IC7002 is supplied including in CCD block assy. 3 C7009 E R7008 R7004 IC7002 C7030 C7012 R7007 R7010 C7005 R7006 E B 6 R7005 4 C7004 R7002 IC7001 3 R7011 1 C L7001 R7012 R7009 C7002 Q7002 FB7001 C7028 C7001 C7003 R7014 1 10 C7007 R7001 C7023 B C 1 20 R7015 R7013 C7006 C7011 2 1 IC7003 3 C7008 4 3 4 R7016 1 C7024 2 C7027 C7026 10 11 C7025 Q7001 C7029 C7010 4 1 R7017 2 C7017 1 RB7001 R7018 SE7002 (PITCH) 2 4 C7014 11 20 C7013 1 28 CN7001 CD-672: 1-871-068- 11 CD-687: 1-871-276- 11 05 CD-672: 1-871-068- 11 05 CD-687: 1-871-276- 11 CD-731 BOARD (SIDE A) CD-731 BOARD (SIDE B) (Non MEGA model) (Non MEGA model) E C7105 B R7103 Q7101 R7101 C L7101 8 1 C7104 C7101 C7106 IC7101 16 C7103 C7108 9 R7102 1 CN7101 16 1-874-671- 05 1-874-671- 11 05 11 Note: IC7101 is not included in CD-731 complete board. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-36 CD-672/CD-687, CD-731 Printed wiring boards of the VC-520 boards are not shown. Pages from 4-37 to 4-38 are not shown. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 FP-569 (1 layer), BL-021 (2 layers): Non MEGA model, BL-022 (2 layers): MEGA model : Uses unleaded solder. D5691 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E OPEN ACCESS 4 2 S56 91 S5692, S5693 (LID OPEN DETECT) 3 3 FP-569 FLEXIBLE BOARD 69 4 S5 FP-569 M903 MOTOR UNIT (GEARD MOTOR) LND001 1 3 M S5694 (EJECT DETECT) S5694 LND002 4 2 Note: M903 is not included in FP-569 flexible complete board. >PI< 2 1 8 69 3 2 3 S5 1 1 4 2 1 05 1-871-283- 11 17 1 K A C5702 A 2 C5701 05 1-874-571- 11 05 1 D5701 21 1-874-571- K 20 CN5702 21 D5702 20 CN5702 R5702 2 1 D5701 (BACKLIGHT) R5701 1 2 CN5701 C5702 R5701 17 18 D5702 (BACKLIGHT) C5703 2 CN5701 (MEGA model) (MEGA model) (Non MEGA model) 18 BL-022 BOARD (SIDE B) BL-022 BOARD (SIDE A) BL-021 BOARD (SIDE B) (Non MEGA model) C5703 BL-021 BOARD (SIDE A) C5701 11 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-39 1-874-572- 11 05 1-874-572- 11 FP-569, BL-021, BL-022 RV-011 (2 layers), PD-351 (2 layer): Non MEGA model : Uses unleaded solder. Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E PD-351 BOARD (SIDE A) (Non MEGA model) LN6201 1 D6210 2 3 1 30 R6215 CN6201 R6214 R6226 6 R6203 CN6202 1 C6201 3 4 D6201 1 5 R6202 R6201 RV-011 BOARD (Non MEGA model) R6231 CL6204 S7601 (PANEL REVERSE) 6 1 R6207 E B Q6201 4 6 3 1 Q6202 CL6201 4 3 C6204 CL6202 C6205 C6202 C6203 C R6232 R6230 VD6204 R6209 VD6203 R6233 C6206 VD6202 VD6201 LN6202 D6202 VD6205 VD6206 HARNESS (HN-024) (Gray) LN6203 RV - 011 RV 05 LN7601 G LN7602Q6203 HARNESS (HN-024) (Gray) CL6203 R6229 S7601 VD6207 1-874-594- 11 1 24 CN6205 1 6 CN6204 1-874-583- 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-40 11 RV-011, PD-351 (SIDE A) PD-351 (2 layers): Non MEGA model : Uses unleaded solder. Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E PD-351 BOARD (SIDE B) (Non MEGA model) D6205 A K D6203-D6205 (BACKLIGHT) D6203 A K D6204 A K 1-874-583- 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-41 11 PD-351 (SIDE B) RV-012 (2 layers), PD-352 (2 layers): MEGA model : Uses unleaded solder. MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E PD-352 BOARD (SIDE A) (MEGA model) LN6201 1 D6210 2 3 1 30 R6215 CN6201 R6214 R6226 6 1 C6201 R6203 CN6202 3 4 D6201 1 5 R6202 R6201 RV-012 BOARD (MEGA model) R6231 CL6204 S7601 (PANEL REVERSE) 6 1 R6207 4 6 3 1 Q6202 CL6201 4 3 C6204 CL6202 CL6203 R6229 B E Q6201 Q6203 C6205 C6202 C6203 C HARNESS (HN-024) (Gray) 1-874-595- 11 R6232 R6230 VD6204 VD6203 R6209 VD6202 R6233 LN6202 C6206 LN6203 HARNESS (HN-024) (Gray) VD6201 D6202 RV - 012 RV 05 LN7601 G LN7602 S7601 VD6207 VD6205 VD6206 1 24 CN6205 1 6 CN6204 1-874-584- 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-42 11 RV-012, PD-352 (SIDE A) PD-352 (2 layers): MEGA model : Uses unleaded solder. MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E PD-352 BOARD (SIDE B) (MEGA model) D6205 A K D6203-D6205 (BACKLIGHT) D6203 A K D6204 A K 1-874-584- 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-43 11 PD-352 (SIDE B) CK-191 (2 layers): Non MEGA model : Uses unleaded solder. Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E CK-191 BOARD (SIDE A) (Non MEGA model) 2 LN5803 K D5801 (MS ACCESS) A R5802 4 S5801 3 1 1 3 1 3 VD5807 1 VD5803 VD5801 3 R5801 S5802 S5803 S5806 RESET 4 2 4 2 4 N DISP/ BATT INFO 05 2 1-874-576- 11 VD5806 VD5805 CK-191 BOARD (SIDE B) (Non MEGA model) 1 BH5801 10 BT901 3 HARNESS (HN-024) (Gray) SP901 SPEAKER 05 CN5801 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 VD5804 LN5801 HARNESS (HN-024) (Gray) BT901 BATTERY, LITHIUM SECONDARY LN5802 1 2 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. VD5802 1-874-576- Note: BT901 (lithium battery) is not included in CK-191 complete board. 11 Note: Replace the battery holder (BH5801) together when replacing the lithium battery (BT901) on the CK-191 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium battery next. ノート: CK-191基板のリチウム電池(BT901)を交換 する場合はバッテリホルダ(BH5801)も同時 に新品に交換して下さい。(一度使用した バッテリホルダは再使用できません。) 部品取り付けの際は,先にバッテリホルダを 取り付けてからリチウム電池を装着してくだ さい。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-44 CK-191 CK-192 (2 layers): MEGA model : Uses unleaded solder. MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E CK-192 BOARD (SIDE A) (MEGA model) 2 LN5803 K D5801 (MS ACCESS) R5802 A 4 S5801 3 1 3 1 3 VD5807 1 VD5803 VD5801 1 3 R5801 S5802 S5803 S5806 RESET 4 2 DISP/ BATT INFO 05 4 2 4 2 N DUBBING 1-874-577- 11 VD5806 VD5805 CK-192 BOARD (SIDE B) (MEGA model) 1 BH5801 10 BT901 3 HARNESS (HN-024) (Gray) SP901 SPEAKER 05 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 VD5804 LN5801 HARNESS (HN-024) (Gray) BT901 BATTERY, LITHIUM SECONDARY CN5801 LN5802 Note: BT901 (lithium battery) is not included in CK-192 complete board. 1 2 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. VD5802 1-874-577- 11 Note: Replace the battery holder (BH5801) together when replacing the lithium battery (BT901) on the CK-192 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium battery next. ノート: CK-192基板のリチウム電池(BT901)を交換 する場合はバッテリホルダ(BH5801)も同時 に新品に交換して下さい。(一度使用した バッテリホルダは再使用できません。) 部品取り付けの際は,先にバッテリホルダを 取り付けてからリチウム電池を装着してくだ さい。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-45 CK-192 MS-391 (2 layers): Non MEGA model : Uses unleaded solder. Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MS-391 BOARD (SIDE B) (Non MEGA model) MS-391 BOARD (SIDE A) (Non MEGA model) LN7301 MEMORY STICK DUO 1 LN7303 1-874-627- 11 FB7302 FB7303 FB7304 R7308 R7307 R7303 R7304 R7305 CN7301 R7301 C7301 16 1 11 11 FB7301 1-874-627- R7302 05 R7306 3 5 2 IC7301 R7310 C7302 1 4 CN7302 VD7301 S7301 10 S7301 PANEL OPEN/CLOSE 12 LN7302 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-46 MS-391 MS-392 (2 layers): MEGA model : Uses unleaded solder. MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E MS-392 BOARD (SIDE B) (MEGA model) MS-392 BOARD (SIDE A) (MEGA model) LN7301 MEMORY STICK DUO 3 5 2 1 IC7301 R7310 C7302 1 4 CN7302 VD7301 S7301 10 S7301 PANEL OPEN/CLOSE 12 LN7302 LN7303 1-874-628- 11 05 11 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-47 FB7301 FB7302 FB7303 FB7304 R7308 R7307 R7303 R7304 R7301 05 R7305 1 R7302 C7301 16 CN7301 R7306 1-874-628- 11 MS-392 FP-839 (1 layer) : Uses unleaded solder. J001 DC IN FP-839 FLEXIBLE BOARD 2 mk OR 3 2 1 C BH001 BATTERY TERMINAL C FP-839 2 4 XX 1-874-948- >P1< 1 Note: BH001 and J001 are not included in FP-839 flexible board. 24 05 1 1-874-948- 11 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 4-48E FP-839 NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS Link A OVERALL SECTION B CABINET R SECTION-1 E BT/EVF SECTION C CABINET R SECTION-2 F CABINET L SECTION D LCD SECTION G H LENS SECTION (DVD110E/ DVD115E/DVD610/DVD610E) MD SECTION I LENS SECTION (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) Link ELECTRICAL PARTS LIST ACCESSORIES BL-021 BOARD E CK-191 BOARD C MS-392 BOARD B BL-022 BOARD E CK-192 BOARD C PD-351 BOARD D CD-672 BOARD I FP-569 FLEXIBLE BOARD F PD-352 BOARD D CD-687 BOARD I FP-839 FLEXIBLE BOARD E RV-011 BOARD D CD-731 BOARD H MS-391 BOARD B RV-012 BOARD D DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST (ENGLISH) NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • CAPACITORS: uF: µF • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD... When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • Color Indication of Appearance Parts Example: (SILVER) : Cabinet’s Color (Silver) : Parts Color (JAPANESE) 【使用上の注意】 • ここに記載されている部品は, 補修用部品であるため, 回路図及び セットに付いている部品と異なる場合があります。 • -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合 があります。 • *印の部品は常備在庫しておりません。 • コンデンサの単位でuFはμFを示します。 • 抵抗の単位Ωは省略してあります。 金 被:金属被膜抵抗。 サンキン:酸化金属被膜抵抗。 • インダクタの単位でuHはμHを示します。 • 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ A..., μPA..., μPB..., μPC..., μPD...を示します。 • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-1 お願い 図面番号で部品を指定するときは基板名又はブロック を併せて指定してください。 0印の部品,または0印付の点線で囲まれた部品は, 安全性を維持するために,重要な部品です。 従って交換時は,必ず指定の部品を使用してください。 • 外装部品色表示 例: (SILVER):セットの色を表す。 (Silver) : 部品の色を表す。 5. REPAIR PARTS LIST DISASSEMBLY 5-1. EXPLODED VIEWS HARDWARE LIST 5-1-1. OVERALL SECTION #11 Cabinet L Section (See page 5-7) #3 #2 BT/EVF Section (See page 5-6) #2 #2 #3 Cabinet R Section-1 (See page 5-3) #2 4 1 #2 2 #2 3 Ref. No. 1 2 3 3 3 Part No. Description Ref. No. 3-281-796-01 WINDOW, REMOTE CONTROL 1-874-951-11 FP-842 FLEXIBLE BOARD 3-281-791-01 COVER, R (DVD110E/DVD115E/DVD610/DVD610E) 3-281-791-11 COVER, R (DVD310E/DVD710/DVD710E) 3-281-791-21 COVER, R (DVD410E/DVD810/DVD810E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-2 4 #2 #3 #11 Part No. Description 3-281-795-01 2-635-562-31 2-660-401-01 3-078-890-11 LID, MS SCREW (M1.7) (Black) SCREW (M1.7), NEW TRU-STAR, P2 (Red) SCREW, TAPPING (Silver) 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. CABINET R SECTION-1 56 Cabinet R Section-2 (See page 5-4) #11 #3 57 55 #11 LCD Section (See page 5-5) 54 #2 53 52 51 Ref. No. 51 Part No. Description Ref. No. 52 52 3-281-848-01 CABINET (C), P (261) (DVD110E/DVD115E/DVD610/DVD610E) 3-281-848-11 CABINET (C), P (261) (DVD310E/DVD710/DVD710E) 3-281-848-21 CABINET (C), P (261) (DVD410E/DVD810/DVD810E) 3-281-849-01 BELT, (P) CABINET (C) (DVD110E) 3-281-849-11 BELT, (P) CABINET (C) (DVD115E) 52 52 52 52 52 3-281-849-21 3-281-849-31 3-281-849-41 3-281-849-51 3-281-849-61 53 A-1438-687-A COVER ASSY (261), JACK (DVD110E/DVD115E/DVD610/DVD610E) A-1438-690-A COVER ASSY (262), JACK (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 51 51 53 BELT, (P) CABINET (C) (DVD610/DVD610E) BELT, (P) CABINET (C) (DVD310E) BELT, (P) CABINET (C) (DVD710/DVD710E) BELT, (P) CABINET (C) (DVD410E) BELT, (P) CABINET (C) (DVD810/DVD810E) 54 54 55 55 * 56 * 57 #2 #3 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-3 #11 Part No. Description A-1436-155-A PANEL ASSY (261), F (DVD110E/DVD115E/DVD610/DVD610E) A-1436-156-A PANEL ASSY (262), F (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) A-1439-631-A MS-391 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) A-1439-645-A MS-392 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 3-281-850-01 FRAME, MS 3-291-848-01 GASKET (TO) 2-635-562-31 SCREW (M1.7) (Black) 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) 3-078-890-11 SCREW, TAPPING (Silver) 5. REPAIR PARTS LIST DISASSEMBLY 5-1-3. CABINET R SECTION-2 ! : Board BT901 (BATTERY, STORAGE, LITHIUM) on the mount position. (See page 4-44, 45) SP901 ns: not supplied 112 110 101 113 BT901 (Note) 109 HARDWARE LIST 111 BH5801 (Note) #11 107 #3 ns #11 107 ns 105 106 108 104 102 • Refer to page 5-1 for mark 0. 103 Note: Replace the battery holder (BH5801) together when replacing the lithium battery (BT901) on the CK-191/192 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium battery next. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Note: CK-191/192基板のリチウム電池(BT901)を交換する場合 はバッテリホルダ(B H 5 8 0 1 )も同時に新品に交換して下 さい。(一度使用したバッテリホルダは再使用できませ ん。) 部品取り付けの際は,先にバッテリホルダを取り付けてか らリチウム電池を装着してください。 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 Ref. No. Part No. * 101 102 103 3-290-774-01 SHEET (261), MUFFLE 1-871-287-11 FP-573 FLEXIBLE BOARD 3-281-846-01 COVER (C), HINGE (DVD110E/DVD115E/DVD610/DVD610E) 3-281-846-11 COVER (C), HINGE (DVD310E/DVD710/DVD710E) 3-281-846-21 COVER (C), HINGE (DVD410E/DVD810/DVD810E) 103 103 104 105 106 106 106 107 108 Description X-2187-937-1 HINGE ASSY (281M) 3-281-847-01 COVER (M), HINGE A-1519-609-A CABINET (R) ASSY (261) (SERVICE) (DVD110E/DVD115E/DVD610/DVD610E) A-1519-610-A CABINET (R) ASSY (262) (SERVICE) (DVD310E/DVD710/DVD710E) A-1519-611-A CABINET (R) ASSY (263) (SERVICE) (DVD410E/DVD810/DVD810E) 2-589-376-01 FOOT (395), RUBBER 3-281-841-01 CABINET (R), ORNAMENTAL BELT Ref. No. Part No. 109 * 110 111 3-283-643-01 SCREW, TRIPOD 3-281-851-01 FRAME, BOTTOM A-1439-630-A CK-191 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) Description 111 A-1439-643-A CK-192 BOARD, COMPLETE (DVD310E/DVD710/DVD710E) 111 A-1439-644-A CK-192 BOARD, COMPLETE (DVD410E/DVD810/DVD810E) 112 1-964-966-11 HARNESS (HN-024) 113 1-833-210-11 CABLE, FLEXIBLE FLAT (FFC-089) 0*BH5801 1-756-615-51 HOLDER, BATTERY (Note) 0 BT901 SP901 #3 #11 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-4 1-756-134-12 1-825-260-41 2-660-401-01 3-078-890-11 BATTERY, STORAGE, LITHIUM (Note) LOUD SPEAKER (1.6CM) SCREW (M1.7), NEW TRU-STAR, P2 (Red) SCREW, TAPPING (Silver) 5. REPAIR PARTS LIST HARDWARE LIST 5-1-4. LCD SECTION ns: not supplied 163 162 161 LCD901 #11 154 160 159 158 152 156 153 ns 157 155 151 Ref. No. 151 151 * 152 153 154 154 155 156 Part No. Description Ref. No. A-1439-627-A PD-351 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) A-1439-640-A PD-352 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 3-083-393-01 TAPE (P) 1-964-966-11 HARNESS (HN-024) A-1439-628-A RV-011 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) 157 158 159 160 * 161 162 163 A-1439-641-A RV-012 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 2-694-515-01 REFLECTION SHEET (2.7) 2-666-801-11 LIGHT GUIDE (2.7) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-5 Part No. Description 2-694-514-01 DIFFUSION SHEET (2.7) 2-694-513-01 PRISM SHEET H (2.7) 2-694-512-01 2-694-516-01 3-281-839-01 3-281-838-01 1-479-926-11 PRISM SHEET V (2.7) FRONT FRAME (2.7) PLATE (261), LCD GROUND CABINET (M), P (261) SWITCH BLOCK, CONTROL (SB22100) LCD901 A-1363-616-A TP BLOCK ASSY (27STMG08H) (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) LCD901 A-1363-617-A TP BLOCK ASSY (27STMG08T) (DVD110E/DVD115E/DVD610/DVD610E) #11 3-078-890-11 SCREW, TAPPING (Silver) 5. REPAIR PARTS LIST 211 HARDWARE LIST 210 5-1-5. BT/EVF SECTION ns: not supplied 209 #12 208 212 213 LCD902 214 207 206 205 203 204 215 202 201 217 #11 J001 ns BH001 ns 216 219 218 #3 221 #11 220 • Refer to page 5-1 for mark 0. DVD410E/DVD810/DVD810E Ref. No. 201 202 Part No. Description Ref. No. * 203 * 204 1-834-868-11 CABLE, FLEXIBLE FLAT (FFC-140) A-1439-629-A BL-021 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) A-1439-642-A BL-022 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 2-638-820-02 GUIDE, LAMP 2-638-819-01 CUSHION, LCD * 205 * 206 * 207 208 2-638-818-01 2-638-816-01 2-638-815-01 2-899-658-01 202 208 ILLUMINATOR PLATE (TFT), DEFLECTION SPACER, LCD CAP (212), INNER (DVD110E/DVD115E/DVD610/DVD610E) 2-899-659-01 CAP (215), INNER (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 209 210 211 212 213 2-899-660-01 3-281-818-01 3-281-825-01 2-664-667-01 X-2187-715-1 214 2-699-246-01 COVER, DC (IN) Part No. Description 215 216 217 218 A-1519-607-A 2-589-376-01 1-480-495-11 1-874-948-11 PANEL ASSY (261) (SERVICE), BT FOOT (395), RUBBER KEY BLOCK, CONTROL (PS26100) FP-839 FLEXIBLE BOARD 219 1-874-950-11 FP-841 FLEXIBLE BOARD (DVD410E/DVD810/DVD810E) A-1538-642-A MDL4060S3C COMPLETE ASSY (SERVICE) (FLASH MEMORY) (DVD410E/DVD810/DVD810E) 3-096-097-01 CUSHION (P), EMC 1-780-064-21 BATTERY TERMINAL BOARD 1-815-792-11 CONNECTOR, DC-IN (7.2V) (DC IN) 220 * 221 0 BH001 0 J001 PANEL (CF), POLARIZATION CABINET, INNER CABINET, VF SPRING, VF SLIDE EYE CUP ASSY DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-6 LCD902 8-753-241-14 LCX076AKE-1 (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) LCD902 8-753-245-09 LCX059CKK-1 (DVD110E/DVD115E/DVD610/DVD610E) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) (DVD410E/DVD810/DVD810E) #11 3-078-890-11 SCREW, TAPPING (Silver) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-6. CABINET L SECTION ns: not supplied #11 251 #11 ns 255 253 256 MD Section (See page 5-8) #11 ns 254 ns ns #11 252 ns #2 #11 #11 M903 Ref. No. Part No. Description 251 252 253 254 * 255 2-699-266-01 A-1519-608-A 3-090-616-01 A-1228-528-A 2-699-262-01 LIGHT, ACCESS GUIDE, CABINET (L) ASSY (261) (SERVICE) SHAFT (F), STRAP FP-569 FLEXIBLE BOARD, COMPLETE SHEET METAL, LID Ref. No. 256 M903 #2 #11 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-7 Part No. Description 3-281-794-01 1-787-237-11 2-635-562-31 3-078-890-11 CABINET (L (UPPER)) MOTOR UNIT (GEARD MOTOR) SCREW (M1.7) (Black) SCREW, TAPPING (Silver) 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-7. MD SECTION Lens Section (DVD110E/DVD115E/DVD610/DVD610E: See page 5-9) (DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E: See page 5-10) #16 #3 305 304 306 303 VC -52 0 302 #3 301 • Refer to page 5-1 for mark 0. Ref. No. Part No. * 301 302 3-281-793-01 LABEL, REPLACEMENT CAUTION A-1439-718-A VC-520 BOARD, COMPLETE (SERVICE) (DVD110E) A-1439-719-A VC-520 BOARD, COMPLETE (SERVICE) (DVD115E) A-1439-720-A VC-520 BOARD, COMPLETE (SERVICE) (DVD610/DVD610E) A-1439-739-A VC-520 BOARD, COMPLETE (SERVICE) (DVD310E) 302 302 302 302 302 Description Ref. No. A-1439-741-A VC-520 BOARD, COMPLETE (SERVICE) (DVD710) A-1439-742-A VC-520 BOARD, COMPLETE (SERVICE) (DVD710E) 302 302 302 * 303 304 * 305 0 306 #3 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-8 #16 Part No. Description A-1439-744-A VC-520 BOARD, COMPLETE (SERVICE) (DVD410E) A-1439-745-A VC-520 BOARD, COMPLETE (SERVICE) (DVD810) A-1439-746-A VC-520 BOARD, COMPLETE (SERVICE) (DVD810E) 3-281-792-01 X-2187-713-1 2-596-924-11 A-1212-602-A 2-660-401-01 GUARD, OP FLEXIBLE FRAME ASSY, MD GASKET (MD) SERVICE (DDX-C2000) BLOCK ASSY SCREW (M1.7), NEW TRU-STAR, P2 (Red) 2-586-337-01 SCREW, MD (Silver) 5. REPAIR PARTS LIST HARDWARE LIST 5-1-8. LENS SECTION (DVD110E/DVD115E/DVD610/DVD610E) ns: not supplied 360 361 366 #3 362 363 #3 359 MIC901 358 364 ns #11 365 #11 357 #12 IC7101 (Note) 353 354 356 355 Note : Be sure to read “Precautions for Replacement of Imager” on page 4-2 when changing the imager. 352 351 Note : イメージャの交換時は4 - 3 ページの“イメージャ 交換時の注意”を必ずお読みください。 Ref. No. Part No. Description Ref. No. Part No. * 351 352 353 354 355 3-281-814-01 8-848-839-01 1-788-706-11 3-271-382-01 1-834-363-11 SHEET, LENS TERMINAL PROTECTION DEVICE, LENS LSV-1171A OPTICAL FILTER BLOCK (OFB-08-02) SEAL RUBBER 1171 CABLE, FLEXIBLE FLAT (FFC-133) * 362 * 363 3-281-810-01 INSULATOR 3-281-808-01 HOLDER, MICROPHONE 356 * 357 358 * 359 360 A-1439-626-A 3-281-802-01 3-281-803-01 2-699-280-01 3-281-805-01 CD-731 BOARD, COMPLETE FRAME, LENS KNOB (261), NS PLATE, NS CLICK GRILLE, MICROPHONE (261) (DVD110E/DVD610/DVD610E) * 364 * 365 366 IC7101 3-281-811-01 2-898-042-01 3-281-807-01 8-753-289-10 360 361 361 3-281-806-01 GRILLE, MICROPHONE (262) (DVD115E) 3-281-812-01 CABINET, TOP (261) (DVD110E/DVD610/DVD610E) 3-281-812-11 CABINET, TOP (261) (DVD115E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-9 IC7101 Description CUSHION, MICROPHONE GASKET (MIC) SCREEN, WIND ICX651NKF-H (CCD IMAGER) (DVD110E/DVD115E/DVD610E) (Note) 8-753-288-68 ICX650NKF-H (CCD IMAGER) (DVD610) (Note) MIC901 1-542-723-31 MICROPHONE UNIT (DVD115E) MIC901 1-542-723-41 MICROPHONE UNIT (DVD110E/DVD610/DVD610E) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) #11 3-078-890-11 SCREW, TAPPING (Silver) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) 5. REPAIR PARTS LIST HARDWARE LIST 5-1-9. LENS SECTION (DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E) ns: not supplied 414 413 415 421 #3 411 #2 #3 CN901 416 410 417 #11 #3 420 409 405 MIC901 (Note 1) #3 408 404 403 ns (IC7002) 418 #12 ns 407 ns (Note 2) 419 #11 406 Note 1: Be sure to read “Precautions for Replacement of Imager” on page 4-2 when changing the imager. Note 1: イメージャの交換時は4-3ページの“イメージャ 交換時の注意”を必ずお読みください。 402 401 Note 2: CD-672 complete board is supplied instead of CD-687 complete board, because CD-672 complete board and CD-687 complete board are compatible. Note 2: CD-687基板は供給されません。代わりにCD-672 基板が供給されます。 Ref. No. Part No. Description * 401 402 403 404 405 3-281-814-01 A-1248-849-A 1-788-523-11 3-088-645-01 A-1511-867-A SHEET, LENS TERMINAL PROTECTION LENS (BLOCK ASSY 1180 (J1)) OPTICALFILTER BLOCK (OFB-06-11) RUBBER (Z), SEAL CCD BLOCK ASSY (1M SSGE) (CCD IMAGER) (Note 1) 406 407 Ref. No. 407 408 * 409 1-874-947-11 FP-838 FLEXIBLE BOARD A-1244-919-A CD-672 BOARD, COMPLETE (DVD710E/DVD810E) A-1244-919-A CD-687 BOARD, COMPLETE (Note 2) 1-874-949-11 FP-840 FLEXIBLE BOARD 3-281-802-01 FRAME, LENS 410 * 411 413 414 3-281-804-01 2-699-280-01 3-281-806-01 A-1438-988-A 414 415 Part No. Description * 416 * 417 * 418 3-281-813-01 CABINET, TOP (262) (DVD310E/DVD710/DVD710E) 3-281-813-11 CABINET, TOP (262) (DVD410E/DVD810/DVD810E) 3-281-810-01 INSULATOR 3-281-808-01 HOLDER, MICROPHONE 3-281-811-01 CUSHION, MICROPHONE * 419 * 420 421 CN901 MIC901 2-898-042-01 3-096-097-01 3-281-807-01 1-818-890-11 1-542-723-31 GASKET (MIC) CUSHION (P), EMC SCREEN, WIND CONNECTOR, EXTERNAL (HOT SHOE) MICROPHONE UNIT #2 #3 #11 #12 2-635-562-31 2-660-401-01 3-078-890-11 3-080-204-21 SCREW (M1.7) (Black) SCREW (M1.7), NEW TRU-STAR, P2 (Red) SCREW, TAPPING (Silver) SCREW, TAPPING, P2 (Black) 415 KNOB (262), NS PLATE, NS CLICK GRILLE, MICROPHONE (262) COVER ASSY (262), SHOE (DVD310E/DVD710/DVD710E) A-1438-989-A COVER ASSY (263), SHOE (DVD410E/DVD810/DVD810E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-10 BL-021 BL-022 CD-672 CD-687 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. A-1439-629-A BL-021 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) ********************** < CAPACITOR > C5701 C5702 1-125-777-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 0.1uF 1uF 10% 10% 10V 10V Part No. Description C7015 C7016 C7017 1-125-777-11 CERAMIC CHIP 1-125-777-11 CERAMIC CHIP 1-125-777-11 CERAMIC CHIP 0.1uF 0.1uF 0.1uF 10% 10% 10% 10V 10V 10V C7018 C7023 C7024 C7025 C7026 1-125-777-11 1-127-760-11 1-165-989-11 1-165-989-11 1-100-251-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 4.7uF 10uF 10uF 0.047uF 10% 10% 10% 10% 10% 10V 6.3V 6.3V 6.3V 10V C7027 C7028 C7029 1-100-251-11 CERAMIC CHIP 1-165-989-11 CERAMIC CHIP 1-165-989-11 CERAMIC CHIP 0.047uF 10uF 10uF 10% 10% 10% 10V 6.3V 6.3V < CONNECTOR > * CN5701 1-779-333-51 CONNECTOR, FFC/FPC 18P * CN5702 1-817-698-81 CONNECTOR, FPC (ZIF) 21P < DIODE > D5701 * D5702 < CONNECTOR > 8-719-074-67 DIODE EDZ-TE61-5.6B 6-501-591-01 DIODE NESW007AT-T099 (BACKLIGHT) CN7001 1-820-586-51 CONNECTOR, FFC/FPC 28P < FERRITE BEAD > < RESISTOR > FB7001 1-400-331-11 FERRITE, EMI (SMD) (1005) R5702 1-218-989-11 RES-CHIP 1M 5% 1/16W < IC > IC7002 A-1439-642-A BL-022 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) ********************** IC7003 (Not supplied) ICX617AKF-H (CCD IMAGER) (Note 2) (IC7002 is supplied including in CCD block assy.) 8-759-489-19 IC uPC6756GR-8JG-E2 < COIL > < CAPACITOR > C5701 C5702 1-125-777-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 0.1uF 1uF 10% 10% L7001 L7002 10V 10V 1-400-588-11 INDUCTOR 1-400-588-11 INDUCTOR 10uH 10uH < TRANSISTOR > < CONNECTOR > Q7001 Q7002 * CN5701 1-779-333-51 CONNECTOR, FFC/FPC 18P * CN5702 1-817-698-81 CONNECTOR, FPC (ZIF) 21P 6-550-234-01 TRANSISTOR 8-729-055-21 TRANSISTOR UNR32A300LS0 2SC5096-O/R (TE85L) < RESISTOR > < DIODE > * D5701 D5702 6-501-591-01 DIODE NESW007AT-T099 (BACKLIGHT) 8-719-074-67 DIODE EDZ-TE61-5.6B A-1244-919-A CD-672 BOARD, COMPLETE (DVD710E/DVD810E) A-1244-919-A CD-687 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) (Note 1) ********************** (IC7002 (CCD imager) is not included in CD-672/CD-687 complete board. Included in CCD block assy.) R7002 R7004 R7005 R7006 R7013 1-218-954-11 1-218-965-11 1-218-953-11 1-218-966-11 1-218-965-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1.2K 10K 1K 12K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R7014 R7015 R7016 1-218-989-11 RES-CHIP 1-218-989-11 RES-CHIP 1-218-965-11 RES-CHIP 1M 1M 10K 5% 5% 5% 1/16W 1/16W 1/16W < COMPOSITION CIRCUIT BLOCK > * RB7001 1-234-379-21 RES, NETWORK 22K (1005X4) < ANGULAR VELOCITY SENSOR > < CAPACITOR > C7002 C7003 C7005 C7006 1-100-566-91 1-100-566-91 1-125-777-11 1-100-591-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 1uF 10% 10% 10% 10% C7007 1-127-820-11 CERAMIC CHIP 4.7uF 10% C7010 1-125-777-11 CERAMIC CHIP 0.1uF 10% C7011 1-165-875-11 CERAMIC CHIP 10uF 10% 25V 25V 10V 25V (CD-672) 16V * SE7001 1-479-022-61 SENSOR, ANGULAR VELOCITY (YAW) * SE7002 1-479-022-51 SENSOR, ANGULAR VELOCITY (PITCH) 10V (CD-672) 10V Note 1: CD-672 complete board is supplied instead of CD-687 complete board, because CD-672 complete board and CD-687 complete board are compatible. Note 1: CD-687基板は供給されません。代わりにCD-672 基板が供給されます。 Note 2: Be sure to read “Precautions for Replacement of Imager” on page 4-2 when changing the imager. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-11 Note 2: イメージャの交換時は4-3ページの“イメージャ 交換時の注意”を必ずお読みください。 CD-731 Ref. No. Part No. Description Ref. No. A-1439-626-A CD-731 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) ********************** (IC7101 is not included in CD-731 complete board.) S5806 1-124-779-00 1-100-567-81 1-124-779-00 1-164-854-11 1-100-566-91 ELECT CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.01uF 10uF 15PF 0.1uF 20% 10% 20% 5% 10% CK-192 Description 1-771-844-21 SWITCH, TACTILE (SMD) (N) A-1439-643-A CK-192 BOARD, COMPLETE (DVD310E/DVD710/DVD710E) A-1439-644-A CK-192 BOARD, COMPLETE (DVD410E/DVD810/DVD810E) ********************** (BT901 (lithium battery) is not included in CK-192 complete board.) < CAPACITOR > C7101 C7103 C7104 C7105 C7108 Part No. CK-191 16V 25V 16V 50V 25V < BATTERY HOLDER > 0* BH5801 1-756-615-51 HOLDER, BATTERY (Note 2) < CONNECTOR > < BATTERY > * CN7101 1-816-646-51 FFC/CONNECTOR, FPC (LIF) 16P 0 BT901 1-756-134-12 BATTERY, STORAGE, LITHIUM ION (Note 2) < IC > < CONNECTOR > IC7101 8-753-288-68 ICX650NKF-H (CCD IMAGER) (DVD610) IC7101 (Note 1) 8-753-289-10 ICX651NKF-H (CCD IMAGER) (DVD110E/DVD115E/DVD610E) (Note 1) * CN5801 1-816-643-51 FFC/CONNECTOR, FPC (LIF) 10P < COIL > L7101 1-400-588-11 INDUCTOR D5801 10uH 6-551-873-01 TRANSISTOR 2SC3931G0LS0 R5801 1-218-954-11 RES-CHIP R5802 1-218-945-11 RES-CHIP 1-218-959-11 RES-CHIP 1.2K 5% 1/16W (DVD410E/DVD810/DVD810E) 220 5% 1/16W < SWITCH > < RESISTOR > R7101 8-719-077-09 DIODE CL-196HR-CD-T (MS ACCESS) < RESISTOR > < TRANSISTOR > * Q7101 < DIODE > 3.3K 5% S5801 S5802 S5803 1/16W A-1439-630-A CK-191 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) ********************** (BT901 (lithium battery) is not included in CK-191 complete board.) < BATTERY HOLDER > S5806 1-771-844-21 SWITCH, TACTILE (SMD) (RESET) 1-771-844-21 SWITCH, TACTILE (SMD) (DISP/BATT INFO) 1-771-844-21 SWITCH, TACTILE (SMD) (DUBBING) (DVD410E/DVD810/DVD810E) 1-771-844-21 SWITCH, TACTILE (SMD) (N) Note 1: Be sure to read “Precautions for Replacement of Imager” on page 4-2 when changing the imager. 0* BH5801 1-756-615-51 HOLDER, BATTERY (Note 2) Note 1: イメージャの交換時は4 - 3 ページの“イメージャ 交換時の注意”を必ずお読みください。 < BATTERY > 0 BT901 1-756-134-12 BATTERY, STORAGE, LITHIUM ION (Note 2) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. < CONNECTOR > * CN5801 1-816-643-51 FFC/CONNECTOR, FPC (LIF) 10P 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 < DIODE > D5801 8-719-077-09 DIODE CL-196HR-CD-T (MS ACCESS) Note 2: Replace the battery holder (BH5801) together when replacing the lithium battery (BT901) on the CK-191 board and CK-192 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium battery next. < RESISTOR > R5802 1-218-945-11 RES-CHIP 220 5% 1/16W < SWITCH > S5801 S5802 1-771-844-21 SWITCH, TACTILE (SMD) (RESET) 1-771-844-21 SWITCH, TACTILE (SMD) (DISP/BATT INFO) Note 2: CK-191基板およびCK-192基板のリチウム電池(BT901) を交換する場合はバッテリホルダ(BH5801)も同時に 新品に交換して下さい。(一度使用したバッテリホルダ は再使用できません。) 部品取り付けの際は,先にバッテリホルダを取り付けて からリチウム電池を装着してください。 • Refer to page 5-1 for mark 0. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-12 FP-569 Ref. No. Part No. Description FP-839 Ref. No. MS-391 MS-392 Part No. A-1228-528-A FP-569 FLEXIBLE BOARD, COMPLETE ******************************* FB7301 FB7302 FB7303 FB7304 6-500-817-01 DIODE SML-512UWT86 (ACCESS) 1-469-580-21 1-469-580-21 1-469-580-21 1-469-580-21 < SWITCH > S5691 S5692 S5693 S5694 1-786-148-11 1-786-148-11 1-786-148-11 1-786-179-31 SWITCH, PUSH (1 KEY) (OPEN) SWITCH, PUSH (1 KEY) (LID OPEN DETECT) SWITCH, PUSH (1 KEY) (LID OPEN DETECT) SWITCH, PUSH (1 KEY) (EJECT DETECT) * IC7301 6-600-563-01 IC RS-450-T < RESISTOR > < BATTERY TERMINAL > R7302 R7303 R7306 R7307 1-218-942-11 1-218-942-11 1-218-942-11 1-218-942-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 120 120 120 120 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W < SWITCH > * S7301 1-786-545-41 SWITCH, PUSH LEVER (S) (PANEL OPEN/CLOSE) 1-780-064-21 BATTERY TERMINAL BOARD < CONNECTOR > 0 J001 INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) < IC > 1-874-948-11 FP-839 FLEXIBLE BOARD ******************** (BH001 and J001 are not included in FP-839 flexible board.) 0 BH001 Description < FERRITE BEAD > < DIODE > D5691 PD-351 A-1439-627-A PD-351 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) ********************** 1-815-792-11 CONNECTOR, DC-IN (7.2V) (DC IN) < CAPACITOR > A-1439-631-A MS-391 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) *********************** C6202 C6203 C6205 C6206 < CONNECTOR > 1-100-581-81 1-100-581-81 1-165-908-11 1-125-777-11 INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) 1-218-942-11 1-218-942-11 1-218-942-11 1-218-942-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 120 120 120 120 5% 5% 5% 5% D6202 * D6203 * D6204 * D6205 1/16W 1/16W 1/16W 1/16W 8-719-074-67 6-501-476-01 6-501-476-01 6-501-476-01 DIODE DIODE DIODE DIODE EDZ-TE61-5.6B NSSW008CT-T071 (BACKLIGHT) NSSW008CT-T071 (BACKLIGHT) NSSW008CT-T071 (BACKLIGHT) < TRANSISTOR > Q6201 Q6202 < SWITCH > * S7301 50V 50V 10V 10V < DIODE > < RESISTOR > R7302 R7303 R7306 R7307 10% 10% 10% 10% * CN6201 1-818-072-61 CONNECTOR, FFC/FPC (ZIF) 30P * CN6202 1-818-069-61 CONNECTOR, FFC/FPC (ZIF) 6P * CN6204 1-818-069-61 CONNECTOR, FFC/FPC (ZIF) 6P CN6205 1-815-031-51 FFC/CONNECTOR, FPC (ZIF) 24P < FERRITE BEAD > 1-469-580-21 1-469-580-21 1-469-580-21 1-469-580-21 0.0047uF 0.0047uF 1uF 0.1uF < CONNECTOR > * CN7301 1-816-646-51 FFC/CONNECTOR, FPC (LIF) 16P CN7302 1-819-613-22 MEMORY STICK DUO CONNECTOR 10P FB7301 FB7302 FB7303 FB7304 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 8-729-427-67 TRANSISTOR 8-729-427-37 TRANSISTOR 1-786-545-41 SWITCH, PUSH LEVER (S) (PANEL OPEN/CLOSE) A-1439-645-A MS-392 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) ********************** < CONNECTOR > * CN7301 1-816-646-51 FFC/CONNECTOR, FPC (LIF) 16P CN7302 1-819-613-22 MEMORY STICK DUO CONNECTOR 10P • Refer to page 5-1 for mark 0. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-13 XP421F-TXE XP411F-TXE < RESISTOR > R6201 R6202 R6203 R6209 1-218-954-11 1-218-955-11 1-218-957-11 1-218-989-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1.2K 1.5K 2.2K 1M 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W PD-352 Ref. No. Part No. Description Ref. No. A-1439-640-A PD-352 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) ********************** < CAPACITOR > C6202 C6203 C6204 C6205 C6206 1-100-581-81 1-100-581-81 1-165-908-11 1-165-908-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0047uF 0.0047uF 1uF 1uF 0.1uF 10% 10% 10% 10% 10% 50V 50V 10V 10V 10V < CONNECTOR > * CN6201 1-818-072-61 CONNECTOR, FFC/FPC (ZIF) 30P * CN6202 1-818-069-61 CONNECTOR, FFC/FPC (ZIF) 6P * CN6204 1-818-069-61 CONNECTOR, FFC/FPC (ZIF) 6P CN6205 1-815-031-51 FFC/CONNECTOR, FPC (ZIF) 24P < DIODE > D6202 * D6203 * D6204 * D6205 8-719-074-67 6-501-476-01 6-501-476-01 6-501-476-01 DIODE DIODE DIODE DIODE EDZ-TE61-5.6B NSSW008CT-T071 (BACKLIGHT) NSSW008CT-T071 (BACKLIGHT) NSSW008CT-T071 (BACKLIGHT) < TRANSISTOR > Q6201 Q6202 * Q6203 8-729-427-67 TRANSISTOR 8-729-427-37 TRANSISTOR 6-551-836-01 TRANSISTOR XP421F-TXE XP411F-TXE 2SA2078G0LS0 < RESISTOR > R6201 R6202 R6203 R6207 R6209 1-218-954-11 1-218-955-11 1-218-957-11 1-218-978-11 1-218-989-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1.2K 1.5K 2.2K 120K 1M 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W A-1439-628-A RV-011 BOARD, COMPLETE (DVD110E/DVD115E/DVD610/DVD610E) ********************** < SWITCH > S7601 1-786-707-11 SWITCH, DETECTION (SMD) (PANEL REVERSE) A-1439-641-A RV-012 BOARD, COMPLETE (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) ********************** < SWITCH > S7601 1-786-707-11 SWITCH, DETECTION (SMD) (PANEL REVERSE) Electrical parts list of the VC-520 board is not shown. Pages 5-15 to 5-24 are not shown. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-14 Part No. Description RV-011 RV-012 • EXCEPT J MODEL to J MODEL Checking supplied accessories. Rechargeable Battery Pack NP-FH40 0 A-1201-658-A (US, CND) 0 A-1201-659-B (EXCEPT US, CND, CH) 0 A-1201-660-A (CH) Power Cord 0 1-555-074-91 (AUS) 0 1-783-952-61 (AR) 0 1-790-107-61 (US, CND) 0 1-792-549-41 (JE) 0 1-824-910-71 (AEP, EE, NE, E: PAL, E: NTSC (Latin America)) 0 1-832-169-31 (UK, HK) 0 1-832-121-31 (CH) 0 1-833-892-21 (KR) 0 1-834-852-11 (E: NTSC (Except Latin America)) Conversion (2P) Adaptor Conversion (2P) Adaptor 0 1-569-008-12 0 1-569-007-12 (E: NTSC (Latin America)) (E: NTSC (Except Latin America)) AC Adaptor (AC-L200/L200B) 0 1-479-285-21 CD-ROM “Handycam Application Software” 3-286-118-01 USB Cable 1-829-868-31 A/V Connecting Cable 1-831-553-11 Operating Guide 3-285-366-11 (ENGLISH) (DVD610: US, CND, E/ DVD710: US, CND, E/DVD810: US, CND, E, JE) 3-285-366-21 (FRENCH) (DVD610: CND/DVD710: CND/ DVD810: CND) 3-285-366-31 (SPANISH) (DVD610: E, AR/DVD710: E, AR/ DVD810: E, AR, JE) 3-285-366-41 (PORTUGUESE) (DVD810: JE) 3-285-366-51 (TRADITIONAL CHINESE) (DVD610: E/ DVD710: E/DVD810: E) 3-285-366-61 (KOREAN) (DVD810: KR, JE) 3-285-367-11 (ENGLISH) (DVD110E/DVD115E/DVD310E/ DVD410E/DVD610E: E, HK, AUS/DVD710E: E/ DVD810E: E, HK, AUS, JE) 3-285-367-21 (FRENCH) (DVD110E: AEP/DVD115E: AEP/ DVD310E: AEP/DVD410E: AEP) 3-285-367-31 (GERMAN, DUTCH) (DVD110E: AEP/ DVD115E: AEP/DVD310E: AEP/DVD410E: AEP) 3-285-367-41 (SPANISH, PORTUGUESE) (DVD110E: AEP/ DVD115E: AEP/DVD310E: AEP/DVD410E: AEP) 3-285-367-51 (ITALIAN, GREEK) (DVD110E: AEP/ DVD115E: AEP/DVD310E: AEP/DVD410E: AEP) 3-285-367-61 (RUSSIAN, SWEDISH) (DVD110E: NE/ DVD115E: NE/DVD310E: NE/DVD410E: NE/ DVD610E: NE/DVD810E: NE, JE) 3-285-367-71 (DANISH, FINNISH) (DVD110E: NE/ DVD115E: NE/DVD310E: NE/DVD410E: NE/ DVD610E: NE/DVD810E: NE) 3-285-367-81 (UKRAINIAN) (DVD110E: NE/DVD115E: NE/ DVD310E: NE/DVD410E: NE/DVD610E: NE/ DVD810E: NE) 3-285-367-91 (POLISH, CZECH) (DVD110E: EE/ DVD115E: EE/DVD310E: EE/DVD410E: EE) 3-285-368-11 (HUNGARIAN, SLOVAK) (DVD110E: EE/ DVD115E: EE/DVD310E: EE/DVD410E: EE) 3-285-368-21 (TURKISH) (DVD110E: EE/DVD115E: EE/ DVD310E: EE/DVD410E: EE) 3-285-368-31 (SIMPLIFIED CHINESE) (DVD610E: E, CH/ DVD710E: E, CH/DVD810E: E, JE) 3-285-368-41 (TRADITIONAL CHINESE) (DVD610E: HK/DVD810E: HK) 3-285-368-51 (ARABIC, PERSIAN) (DVD610E: E/DVD710E: E/DVD810E: E) Wireless Remote Commander RMT-835 1-479-275-41 (DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E) DVD-ROM “ENJOY HANDYCAM” 3-282-264-01 (KR) ENGLISH/KOREAN/JAPANESE 3-282-264-11 (US, CND, E, AR) ENGLISH/FRENCH/SPANISH/PORTUGUESE 3-282-264-21 (AEP, EE, NE, UK) ENGLISH/RUSSIAN/GERMAN 3-282-264-31 (AEP) ENGLISH/SPANISH/PORTUGUESE/ITALIAN 3-282-264-41 (AEP) ENGLISH/FRENCH/PORTUGUESE/DUTCH 3-282-264-61 (E, HK, AUS, CH) ENGLISH/FRENCH/SIMPLIFIED CHINESE for CHINA/ TRADITIONAL CHINESE for HONG KONG 3-282-264-71 (E) ENGLISH/TRADITIONAL CHINESE for TAIWAN/ SPANISH/PORTUGUESE • Refer to page 5-1 for mark 0. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-25 Ver. 1.1 2008.03 Ver. 1.0からの変更部分は 青色で記載されています。 • J MODEL 付属品 AC アダプター (AC-L200/L200B) 0 1-479-285-41 電源コード 0 1-792-549-41 ワイヤレスリモコン RMT-835 1-479-275-41 リチャージブルバッテリー パック NP-FH40 0 A-1201-657-A CD-ROM 「Handycam Application Software」 3-286-118-01 取扱説明書 3-285-366-01 (日本語) USB ケーブル 1-829-868-31 A/V 接続ケーブル 1-831-553-11 • 0マークについては,5-1ページを参照してください。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 5-26E DVD-ROM 「エンジョイハンディーカム」 3-282-264-01 英語/韓国語/日本語 HARDWARE LIST (1/6) #1: M1.7 X 2.5 (Black) 2-635-562-11 #2: M1.7 X 4.0 (Black) 2-635-562-31 #3: M1.7 X 2.5 (Red) 2-660-401-01 1.7 2.5 1.7 4.0 #5: M1.7 X 3.5 (Tapping) (Black) 3-080-204-01 #11: M1.7 X 4.0 (Tapping) (Silver) 3-078-890-11 1.7 1.7 4.0 #13: M1.7 X 2.5 (Tapping) (Silver) 3-085-397-01 1.7 2.5 5.0 #16: M1.4 X 2.5 (Silver) 2-586-337-01 2.5 #19: M1.2 X 4.0 (Tapping) (Red) 3-086-156-21 1.4 1.5 2.5 1.4 1.4 1.5 #18: M1.4 X 2.5 (Silver) 2-635-591-21 1.7 2.2 1.7 1.7 #15: M1.4 X 1.5 (Silver) 3-062-214-01 1.7 #17: M1.7 X 1.5 (Silver) 2-586-389-01 #12: M1.7 X 5.0 (Tapping) (Black) 3-080-204-21 4.0 #14: M1.7 X 2.5 (Silver) 2-599-475-11 2.5 3.5 1.6 #10: M1.7 X 4.0 (Silver) 2-599-475-31 1.7 1.7 1.7 5.0 #8: M1.7 X 3.5 (Tapping) (Silver) 3-078-890-01 1.4 3.5 1.4 2.5 #7: M1.7 X 1.6 (Black) 7-627-552-18 1.7 3.5 1.7 2.5 #6: M1.4 X 1.7 (Silver) 2-598-474-01 #9: M1.7 X 5.0 (Tapping) (Silver) 3-078-890-21 #4: M1.4 X 2.5 (Tapping) (Dark Silver) 3-348-998-81 #20: M1.4 X 3.0 (Silver) 2-635-591-31 1.4 1.2 4.0 3.0 HARDWARE LIST (2/6) #21: M1.4 X 3.0 (Black) 2-662-396-21 #22: M1.7 X 5.0 (Tapping) (Silver) 3-083-261-01 #23: M1.7 X 4.0 (Tapping) (Black) 3-080-204-11 1.7 1.4 5.0 3.0 #25: M1.7 X 3.0 (Black) 2-635-562-21 3.0 3.0 #36: M3.0 X 6.0 (Silver) 4-886-821-11 3.0 4.0 6.0 6.0 #38: M3.0 X 20.0 (Tapping) (Silver) 7-685-651-79 2.0 4.5 #35: M4.0 X 6.0 (Tapping) (Silver) 3-975-291-02 8.0 #37: M2.0 X 6.0 (Tapping) (Black) 3-080-206-31 3.0 4.0 #34: M3.0 X 8.0 (Black) 3-077-331-41 6.0 #32: M2.0 X 4.5 (Tapping) (Silver) 2-102-498-01 1.2 3.5 #33: M3.0 X 6.0 (Silver) 3-077-331-21 4.0 #31: M3.0 X 4.0 (Silver) 2-102-434-01 1.4 1.4 1.4 2.0 #30: M1.2 X 3.5 (Tapping) (White) 3-086-156-11 2.5 #28: M1.4 X 4.0 (Tapping) (Silver) 3-348-998-61 1.4 2.0 #29: M1.4 X 2.5 (Black) 2-662-396-01 5.5 #27: M1.4 X 2.0 (Black) 2-662-396-11 1.7 1.7 1.7 4.0 #26: M1.4 X 2.0 (Silver) 2-635-591-11 3.0 #24: B1.7 X 5.5 (Tapping) (Black) 4-679-805-11 #39: M2.6 X 5.0 (Tapping) (Black) 7-685-791-09 #40: M2.0 X 4.0 (Tapping) (Silver) 7-685-851-04 3.0 2.0 6.0 2.6 20.0 5.0 2.0 4.0 HARDWARE LIST (3/6) #41: M3.0 X 8.0 (Tapping) (Silver) 3-065-748-01 #42: M2.0 X 4.0 (Tapping) (Silver) 7-628-253-00 #43: M1.7 X 4.0 (Red) 2-660-401-31 2.0 3.0 8.0 #46: M1.7 X 3.0 (Red) 2-660-401-11 #49: M2.0 X 4.0 (Black) 2-630-005-31 3.0 #50: M2.0 X 3.0 (Red) 2-891-494-11 2.0 4.0 #48: M1.7 X 2.5 (Silver) 3-973-497-91 1.4 1.7 3.0 1.7 3.0 #47: M1.4 X 3.0 (Tapping) (Silver) 2-665-774-01 1.4 2.5 1.7 4.0 4.0 #45: M1.4 X 2.5 (Silver) 2-587-151-01 #44: M1.7 X 3.0 (Tapping) (Silver) 3-078-890-61 1.7 2.5 #51: M2.0 X 2.5 (Silver) 3-073-686-01 #52: M2.0 X 4.0 (Tapping) (Black) 3-080-206-11 2.0 2.0 2.0 4.0 3.0 2.5 #53: M2.0 X 5.0 (Tapping) (Black) 3-080-206-21 #54: M1.75 X 6.0 (Tapping) (Black) 3-318-203-11 6.0 5.0 #57: M1.7 X 4.0 (Black) 7-627-852-18 #56: M2.0 X 3.5 (Silver) 3-067-187-11 1.75 2.0 2.0 4.0 #58: M2.0 X 6.0 (Tapping) (Silver) 3-719-408-11 6.0 2.0 3.5 #59: M2.0 X 5.0 (Tapping) (Silver) 3-080-205-21 2.0 1.7 4.0 #55: M2.0 X 4.0 (Silver) 2-655-582-11 #60: M2.6 X 5.0 (Black) 3-061-062-11 2.6 2.0 5.0 5.0 HARDWARE LIST (4/6) #61: M3.0 X 10.0 (Black) 7-682-549-09 #62: M2.0 X 3.0 (Silver) 3-080-202-21 3.0 10.0 2.0 12.5 #66: M1.4 X 1.4 (Silver) 2-635-591-41 1.4 3.5 2.0 4.0 3.5 3.5 #76: M1.7 X 4.0 (Tapping) (Silver) 2-666-551-11 1.7 4.0 #79: M1.4X 2.0 (Silver) 2-587-151-11 #80: M1.4X 2.0 (Black) 3-279-411-01 1.4 1.4 1.2 2.0 1.7 1.7 #78: M1.4 X 3.5 (Red) 3-208-537-11 1.4 1.4 #75: M1.7 X 3.5 (Tapping) (Silver) 2-666-551-01 6.0 #77: M1.2 X 5.0 (Tapping) (Silver) 3-086-156-31 #72: M1.4 X 2.0 (Silver) 4-663-621-41 2.0 #74: M1.7 X 6.0 (Tapping) (Silver) 2-666-551-31 1.7 4.0 #71: M1.4 X 2.0 (Red) 3-208-537-01 5.0 1.2 5.0 1.4 1.7 1.7 #73: M1.2 X 4.0 (Tapping) (Black) 3-086-156-61 #68: M1.7 X 4.0 (Silver) 2-655-581-01 1.4 #70: M1.7 X 5.0 (Silver) 2-599-475-41 3.0 5.0 #67: M1.4 X 2.0 (Silver) 3-389-523-16 1.4 #69: M1.7 X 3.0 (Silver) 2-599-475-21 1.7 5.0 3.0 #65: M1.4 X 3.5 (Silver) 2-635-591-01 #64: M1.7 X 5.0 (Tapping) (Silver) 2-666-551-21 #63: M5.0 X 12.5 (Black) 3-060-811-21 2.0 1.4 2.0 HARDWARE LIST (5/6) #81: M1.7 X 2.5 (Silver) 2-515-756-01 #82: M1.4 X 1.4 (Silver) 3-272-251-01 #83: M1.7 X 7.0 (Tapping) (Black) 3-080-204-41 1.7 1.4 2.5 #86: M1.7 X 4.0 (Tapping) (Silver) 2-695-434-21 2.5 #97: M1.4 X 2.5 (Black) 2-662-396-31 1.4 8.0 1.4 2.5 #99: M2.5 X 6.0 (Tapping) (Silver) 3-776-750-02 3.8 8.0 #96: M1.4 X 2.5 (Silver) 2-587-151-21 3.0 1.7 #98: M3.0 X 8.0 (Silver) 3-077-331-01 2.5 3.9 #95: M3.0 X 8.0 (Tapping) (Black) 7-685-646-79 4.0 3.5 2.0 1.7 3.5 #94: M1.7 X 4.0 (Black) 2-515-483-31 1.7 #92: M2.0 X 3.9 (Black) 3-268-954-01 #91: M1.7 X 3.0 (Tapping) (Silver) 2-695-434-11 3.0 1.6 5.9 1.7 2.0 #93: M1.7 X 3.5 (Tapping) (Silver) 3-254-082-01 1.6 5.3 #90: M1.7 X 3.0 (Silver) 3-271-395-01 5.0 #88: M1.6 X 5.9 (Tapping) (Silver) 2-689-015-01 #87: M1.6 X 5.3 (Black) 2-689-328-01 4.0 2.0 3.0 1.7 1.7 #89: M2.0 X 5.5 (Tapping) (Silver) 2-695-575-01 1.7 7.0 1.4 #85: M1.7 X 2.5 (Black) 2-515-483-11 #84: M2.0 X 3.0 (Silver) 3-072-453-11 #100: M2.0 X 6.0 (Black) 3-080-203-51 2.5 6.0 2.0 6.0 HARDWARE LIST (6/6) #102: M2.6 X 8.0 (Black) 7-621-284-30 #101: M2.0 X 5.0 (Silver) 7-621-555-39 2.6 2.0 5.0 #105: M2.0 X 4.0 (Red) 2-891-494-31 10.0 #106: M2.0 X 6.0 (Black) 3-713-786-11 #107: M2.0 X 5.0 (Silver) 3-032-750-01 2.0 4.0 6.0 #109: M1.7 X 3.0 (Black) 2-515-483-21 #110: M2.0 X 3.0 (Black) 2-630-005-21 5.0 #117: M1.7 X 4.5 (Tapping) (Silver) 2-695-429-31 1.4 2.0 #112: M1.4 X 5.0 (Black) 2-178-410-11 1.4 5.0 #115: M1.4 X 3.5 (Tapping) (Silver) 3-348-998-51 #116: M2.0 X 3.5 (Tapping) (Silver) 2-695-435-01 2.0 1.4 3.5 #118: M1.4 X 2.0 (Black) 2-655-580-01 1.7 3.0 4.0 5.5 1.7 1.7 2.0 1.7 #108: M1.7 X 3.0 (Tapping) (Black) 2-695-430-01 #111: M1.7 X 4.0 (Tapping) (Black) 2-887-124-01 #114: M2.0 X 5.5 (Tapping) (Silver) 2-698-464-01 #113: M1.7 X 5.0 (Black) 2-635-562-41 8.0 5.0 3.0 3.0 3.0 2.0 2.0 1.7 #104: M3.0 X 8.0 (Black) 7-682-548-09 2.6 8.0 2.0 4.5 #103: M2.6 X 10.0 (Silver) 7-685-794-09 3.5 Reverse 985224932.pdf Revision History Ver. Date History 1.0 2007.12 Official Release 1.1 2008.03 Revised-1 (A1 DI07-306) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L2 Contents — • Correction of Repair Parts S.M. revised: Page 5-26 S.M. Rev. issued — Yes DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E RMT-835 SERVICE MANUAL LEVEL Ver. 1.1 2008.01 Revision History Revised-1 Replace the previously issued SERVICE MANUAL 9-852-249-11 with this manual. Photo: DCR-DVD810 3 US Model Canadian Model AEP Model UK Model East European Model North European Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Japanese Model Link MODEL INFORMATION TABLE PRINTED WIRING BOARDS REPAIR PARTS LIST SCHEMATIC DIAGRAMS The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DIGITAL VIDEO CAMERA RECORDER DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 9-852-249-12 Sony EMCS Co. 2008A0500-1 © 2008.1 Published by Kohda TEC Model information table Non MEGA model Model Destination DCR-DVD110E DCR-DVD115E AEP, UK, AEP, UK, EE, NE EE, NE Color system 5.1ch recording DCR-DVD610 US, CND, E, AR, BR DCR-DVD610E AEP, E, AUS, HK, CH PAL × PAL a NTSC × PAL × a × a × a a a a Remote commander Active Interface Shoe × × × × × × × × Internal flash memory BL board × BL-021 × BL-021 × BL-021 × BL-021 CD board CK board CD-731 CK-191 CD-731 CK-191 CD-731 CK-191 CD-731 CK-191 MS board PD board MS-391 PD-351 MS-391 PD-351 MS-391 PD-351 MS-391 PD-351 RV board RV-011 RV-011 RV-011 RV-011 Data copy CAM → PC PC → CAM MEGA model Model Destination DCR-DVD310E DCR-DVD410E DCR-DVD710 DCR-DVD710E DCR-DVD810 DCR-DVD810E AEP, UK, AEP, UK, US, CND, E, KR, AEP, E, AUS, US, CND, E, AR AEP, E, CH EE, NE EE, NE AR, JE, J HK, JE Color system 5.1ch recording PAL a PAL a NTSC a PAL a NTSC a PAL a a × a × a a a a a a a a Remote commander Active Interface Shoe a a a a a a a a a a a a Internal flash memory BL board × BL-022 a BL-022 × BL-022 × BL-022 a BL-022 a BL-022 CD board CK board CD-687 CK-192 CD-687 CK-192 CD-687 CK-192 CD-672/CD-687 CK-192 CD-687 CK-192 CD-672/CD-687 CK-192 MS board PD board MS-392 PD-352 MS-392 PD-352 MS-392 PD-352 MS-392 PD-352 MS-392 PD-352 MS-392 PD-352 RV board RV-012 RV-012 RV-012 RV-012 RV-012 RV-012 Data copy CAM → PC PC → CAM • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model MX : Mexican model NE : North European model DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 —2— ENGLISH JAPANESE CAUTION: The use of optical instrument with this product will increase eye hazard. CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. CAUTION Use of controls or adjustments or perfor mance procedures other than those specified herein may result in hazardous radiation exposure. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. 2. 3. 4. 5. 6. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 —3— ENGLISH JAPANESE 注意 電池の交換は,正しく行わないと破裂する恐れがあり ます。電池を交換する場合には必ず同じ型名の電池 又は同等品と交換してください。 サービス,点検時には次のことにご注意下さい。 6. フレキシブルプリント基板の取扱いについて 1. 注意事項をお守りください。 サービスのとき特に注意を要する個所については, キャビネット,シャーシ,部品などにラベルや捺印で • コテ先温度を270℃前後にして行なって下さい。 • 同一パターンに何度もコテ先を当てないで下さい。 注意事項を表示しています。これらの注意書き及び取 扱説明書等の注意事項を必ずお守り下さい。 (3回以内) • パターンに力が加わらないよう注意して下さい。 2. 指定部品のご使用を セットの部品は難燃性や耐電圧など安全上の特性を 7. 無鉛半田について 無鉛半田を使用している基板には,無鉛(Lead Free)を意 持ったものとなっています。従って交換部品は,使用 されていたものと同じ特性の部品を使用して下さい。 味するレッドフリーマークがプリントされています。 (注意: 基板サイズによっては,無鉛半田を使用して 特に回路図,部品表に0印で指定されている安全上重要 な部品は必ず指定のものをご使用下さい。 いてもレッドフリーマークがプリントされて いないものがあります) 3. 部品の取付けや配線の引きまわしはもとどおりに 安全上,チューブやテープなどの絶縁材料を使用した :レッドフリーマーク 無鉛半田には,以下の特性があります。 り,プリント基板から浮かして取付けた部品がありま す。また内部配線は引きまわしやクランパによって発 • 融点が従来の半田よりも約40℃高い。 従来の半田こてをそのまま使用することは可能です 熱部品や高圧部品に接近しないよう配慮されています ので,これらは必ずもとどおりにして下さい。 が,少し長めにこてを当てる必要があります。 温度調節機能のついた半田こてを使用する場合,約 4. サービス後は安全点検を サービスのために取外したネジ,部品,配線がもとど 350℃に設定して下さい。 注意: 半田こてを長く当てすぎると,基板のパター おりになっているか,またサービスした個所の周辺を 劣化させてしまったところがないかなどを点検し,安 ン(銅箔)がはがれてしまうことがあります ので,注意して下さい。 • 粘性が強い 従来の半田よりも粘性が強いため,IC端子などが半田 全性が確保されていることを確認して下さい。 5. チップ部品交換時の注意 • 取外した部品は再使用しないで下さい。 • タンタルコンデンサのマイナス側は熱に弱いため交 ブリッジしないように注意して下さい。 • 従来の半田と混ぜて使用可能 無鉛半田には無鉛半田を追加するのが最適ですが, 従来の半田を追加しても構いません。 換時は注意して下さい。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 —4— 4-2. SCHEMATIC DIAGRAMS Link VC-520 BOARD (1/20) (A/D CONVERTER, TIMING GENERATOR) VC-520 BOARD (11/20) (RF PROCESS ) VC-520 BOARD (2/20) (LENS DRIVE, EVR) VC-520 BOARD (12/20) (DVD MECHA DRIVE) VC-520 BOARD (3/20): Non MEGA model (LENS DRIVE) VC-520 BOARD (13/20) (D/A CONVERTER) VC-520 BOARD (4/20) (LENS DRIVE) VC-520 BOARD (5/20) (CPU (SIGNAL PROCESS 1)) VC-520 BOARD (6/20) (CPU (SIGNAL PROCESS 2)) VC-520 BOARD (7/20) (CPU (POWER SUPPLY)) VC-520 BOARD (8/20) (SDRAM, OneNAND FLASH) VC-520 BOARD (9/20) (DVD DSP, DVD DRIVE CONTROL) VC-520 BOARD (10/20) (SDRAM, FLASH) VC-520 BOARD (14/20): DVD110E/DVD610/ DVD610E (VIDEO OUT, AUDIO I/O) VC-520 BOARD (15/20): DVD115E/DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E (VIDEO, AUDIO I/O) VC-520 BOARD (16/20) (LCD/EVF DRIVE) VC-520 BOARD (17/20) (HI CONTROL) VC-520 BOARD (18/20) (DC IN, CHARGE) VC-520 BOARD (19/20) (DC/DC CONVERTER) VC-520 BOARD (20/20) (CONNECTOR) COMMON NOTE FOR SCHEMATIC DIAGRAMS Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVE610E DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 ENGLISH 4-2. SCHEMATIC DIAGRAMS JAPANESE 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS (ENGLISH) THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 1. Connection Pattern box Color bar chart For PTB-450: J-6020-250-A Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-1450: J-6082-559-A L = 1 m (PTB-450) L = 40 cm (PTB-1450) Pattern box Front of the lens L Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– Line • J : IN/OUT direction of (+,–) B LINE. • C: adjustment for repair. (Measuring conditions voltage and waveform) • Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Camera A B A=B Red Blue White Magenta H Cyan Green Yellow 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. B A Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame Fig.b (Picture on monitor TV) Precautions for Replacement of Imager • If the imager has been replaced, carry out all the adjustments for the camera section. • As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-2 ENGLISH 4-2. SCHEMATIC DIAGRAMS JAPANESE (JAPANESE) 回路図共通ノート (他に必要なノートは各ブロックに記載してあります) 【回路図ノート】 1. 接続図 ・ケミコン,タンタルを除くコンデンサで,耐圧50V以下のもの はその耐圧を省略。単位はすべてμF(pはpF)。 ・チップ抵抗で指示のないものは,1/10W以下。 kΩ=1000Ω,MΩ=1000kΩ ・チップ部品交換時の注意 取り外した部品は再使用せず,未使用の部品をご使用くださ い。 タンタルコンデンサのマイナス側は熱に弱いため注意してくだ さい。 ・チップ部品には下記のように表示したものがあります。 例 C 541 L 452 22U 10UH TA A 2520 ↑ ↑ ↑ 種類 ケースサイズ 外形寸法(mm) ・抵抗,コンデンサ,ICなど定数にXXがあるものは,使用して いない事を示しています。このため,使用していない回路が記 載されている事があります。 ・★印のある部品は,機種などにより異なりますので機能別マウ ント一覧表を参照してください。 ・可変抵抗と半固定抵抗で,B特性の表示を省略。 ・信号名表記について,下記のような場合があります。 XEDIT → EDIT PB/XREC → PB/REC ・2は不燃性抵抗。 ・1はヒューズ抵抗。 ・Cはパネル表示名称。 ・AはB+ライン。 ・BはB−ライン。 ・JはBライン(+,−)の入出力方向を示す。 ・Cは調整名称。 パターンボックス カラーバーチャート For PTB-450: J-6020-250-A Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A For PTB-1450: J-6082-559-A L = 1 m (PTB-450) L = 40 cm (PTB-1450) パターンボックス レンズ前面 L カメラ 2. 図a及び図bの波形が得られるように画枠調整して下さい。 H シ 黄 ア ン A B マ ゼ 白 ン 緑 ダ 赤 A=B 青 B A 図a(映像入出力端子出力波形) 電子ビーム走査線 【電圧・波形測定条件ノート】 ・電圧値及び信号波形はパターンボックスのカラーバーチャート を被写体としたときの測定点対アース間の参考値。 (デジタルマルチメータ;入力インピーダンス DC10MΩ使 用) ・使用テスタの入力インピーダンスにより電圧値が多少異なりま す。 ブラウン管の画像枠 図b(テレビモニタの映像) イメージャ交換時の注意 ・イメージャを交換した場合は,カメラ部の全調整を 行ってください。 ・イメージャは構造上,静電気により破壊される恐れが あるため,MOS ICと同様に注意して取り扱ってくだ さい。 また,受光部にはゴミの付着,および強い光がはいる ことのないように注意してください。 0印の部品,または0印付きの点線で囲まれた部品は, 安全性を維持するために重要な部品です。 従って交換時は,必ず指定の部品を使用して下さい。 お願い 図面番号で部品を指定するときは基板名又はブロック を併せて指定して下さい。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-3 1 2 4 3 6 5 8 7 10 9 11 12 14 13 15 16 A A FB1204 C1216 22u 6.3V TA A_2.8V L1201 10uH A_2.8V C1215 XX AD5 CAM_15/12V C1214 0.1u CAM_DD_ON CH_SI CL1201 C1210 XX CAM_-7.5V V5 V6 SUB CAM_-7.5V FB1201 C1212 4.7u B AD2 B AD3 B C1231 4.7u B C1230 XX C1217 XX C1221 0.1u B CL1202 REG_GND DVSS1 CAM_DD_ON DVDD1 DVSS4 V5 D3 D0 ZSG1 AVDD1 V6 D1 MON2 LINE DVSS12 1 VD C1208 0.1u B VDR_VDD SUB RG C1213 C1202 47p CH 3 2 4 1 RG D10 D11 D7 V1 RESET CLK_O TG_VD TG_HD TG_HD D AD10 V2 4.6 (2.9) <3.4> V3 AD11 CL1203 CAM_15/12V TG_HD 4 3 FB1203 TG_VD CL1204 IC1202 R1114Q291D-TR-FA C1225 4.7u B 2.9V REG : Non MEGA model R1114Q341D-TR-FA 3.4V REG : MEGA model E 2 R1220 XX 4.6 A_4.6V L1203 C1227 C1228 1u B 22u 6.3V XSYS_RST XX C1233 1u B D_2.8V_1 C1220 4.7u REG_GND V1 H1 H2 R1209 XX MEGA model H AD6 C1223 XX F X1201 Page 4-5 of Level 2 TG_VD R1206 XX F FP-838 FLEXIBLE CH_SI AD8 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 C1 C2 C1211 0.1u B G CH_SO C1222 0.1u B 1 H1 16P CN1201 DVSS5 H2 DVSS5 V2 CH_CS CH_SI VCC HD VHH CH_SCK CH_CS CH_SO V_OUT VH CS V4 47 2 AVDD2 R1212 FB1202 CCD_OUT REG_GND D9 CH_SCK RG 3 V3 VRB V1 C XSYS_RST AD4 AD7 AD12 4 V2 VRT AD13 5 RG AVSS12 R1211 XX 6 VSHT REG_GND D8 AD9 CN1203 REG_GND DVDD4 CCD_IN DVDD5 7 FBC C1219 XX 8 H1 HL H2 H2 Page 4-5 of Level 2 DVSS4 SHC NC 9 VM A/D CONVERTER, TIMING GENERATOR CCD_GND R1208 XX 10 V1 D4 IC1201 R2J45015AHBGW0 SDI SCAN V2 V3 ID OSC_I CN7101 Through the Flexible Flat Cable (FFC-133) V4 D6 OSC_O 11 C1205 0.1u B DVDD2 ADCK R1205 C1201 XX 47p CH CD-731 V3 CH_CS LINECK DVDD3 12 V5 DVSS4 DVSS3 V4 MEGA model V6 SCK DLLC 13 DVSS4 DVSS5 14 V5 DVSS4 AVSS12 DVDD5 15 V6 C1207 0.1u B V4 AVSS12 H1 CAM_12.0V R1218 0 SHC R1204 XX E 16 C1209 0.1u B C1206 0.1u B 0.1u B CAM_-7.5V 47 D5 GND Non MEGA model C1203 C1204 0.001u B D2 ZV1 VDR_VDD R1219 R1201 XX 0 R1202 BIAS CE CH_SO Non MEGA model D K10 K9 K8 K7 K6 K5 K4 K3 K2 K1 J10 J9 J8 J7 J6 J5 J4 J3 J2 J1 CH_SCK CAM_DD_ON XSYS_RST R1203 33k C3 C4 C5 C6 C7 C8 C9 C10 D1 D2 D3 D4 D8 D9 D10 E1 E2 E3 E8 E9 E10 AVSS12 AVSS12 DS_GATE MON DVDD1 C DVDD1 VL SUB SDO H10 H9 H8 H7 H6 H5 H4 H3 H2 H1 G10 G9 G8 G3 G2 G1 F10 F9 F8 F3 F2 F1 28P GND 1 CCD_OUT+ 2 GND 3 CAM_15V 4 CAM_-7.5V 5 GND 6 GND 7 RG 8 GND 9 H2 10 GND 11 H1 12 GND 13 GND 14 V1 15 V2 16 V3 17 V4 18 V5 19 V6 20 GND 21 RCSUB 22 SUB 23 G MARKED:MOUNT TABLE RG C1213 X1201 H2 Non MEGA model 0.001u 24MHz MEGA model NTSC 0.01u 33MHz PAL 0.001u 27MHz H1 CHCK V1 V2 AD2 V3 AD3 V4 AD4 V5 AD5 V6 AD6 AD7 CSUB AD8 SUB AD9 SE_GND 24 REG_GND AD10 PITCH_AD 25 PITCH_AD AD11 VST_C_RESET 26 VST_C_RESET AD12 YAW_AD 27 YAW_AD SE_2.8V 28 A_2.8V AD13 AD2 AD3 AD4 H AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E I I J J K K VC-520 BOARD (1/20) A/D CONVERTER, TIMING GENERATOR XX MARK:NO MOUNT NO MARK:REC/PB MODE ( ):Non MEGA model < >:MEGA model L L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-6 VC-520 (1/20) 6 HALL_REF LENS BLOCK is replaced as block, so that there PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted. D_2.8V C5107 XX VCC 2.8 EVR (D/A CONVERTER) RB5101 47k ZOOM_A 1 ZOOM_A ZM_XA ZOOM_XA 2 ZOOM_XA ZM_XB ZOOM_XB 3 ZOOM_XB ZM_B ZOOM_B 4 ZOOM_B GND GND 5 THERMO_OUT TEMP_OUT 6 FC_SENSE_OUT 7 FC_SENS_Vcc FC_SENSE_VCC 8 GND 9 ZM_SENS_Vcc ZM_SENSE_VCC 10 ZM_SENS_OUT ZM_SENSE_OUT 11 I_DRIVE(+) GND 12 I_DRIVE(-) IRIS_DRIVE(+) 13 GND IRIS_DRIVE(-) 14 I_BIAS(+) IRIS_BIAS(+) 15 I_HALL(+) IRIS_HALL(+) 16 I_BIAS(-) IRIS_BIAS(-) 17 IRIS_BIAS_IRIS_HALL_- I_HALL(-) IRIS_HALL(-) 18 IR_SWITCH_OUT IR_SWITCH_OUT 19 GND GND 20 FC_XA FOCUS_XA 21 1 3 5 7 1 3 5 7 2 4 6 8 ZM_RST IRIS_DRIVE_+ 0 RB5102 A_2.8V 1 3 4 2.8 B D_2.8V ZM_RST_LED 5 2.8 REG_GND IRIS_HALL_+ MT_5.0V MT_5.0V_LD VD5101 XX XNS_SW C5104 33u 10V R5172 XX L5101 4.7uH REG_GND C FOCUS_XA FOCUS_A FOCUS_XB FC_B FOCUS_B 24 OP1_A+ A IRIS_BIAS_+ MEGA model 22 FOCUS_B Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E MEGA model R5136 22k : Non MEGA model R5135 22k 18k : MEGA model D OP2_AOUT (1.1) 0.9 0.9 C5105 0.47u B OP2_A- OP2_A+ (R1.3/P0) 4 A_IN- A_IN+ GND 3 2 1 HALL BIAS/GAIN CONTROL : Non MEGA model HALL AMP, HALL GAIN CONTROL : MEGA model B_IN- B_IN+ B_IN- B_OUT Vcc IC5103 NJM12904V(TE2) B_IN+ IC5102 NJM12904V(TE2) 4 A_OUT 3 A_IN- 2 A_OUT REG_GND GND OP1_AOUT (R0.3/P0 ) OP1_A(R1.3/P0.3) IRIS_PWM 1 Vcc REG_GND IRIS_DRIVE_- 23 B_OUT GND CAM_SCK CAM_SO VD5102 XX 2 4 6 8 FOCUS_A 7 (1.9)<2.8> DI FC_RST_LED 6 -0.9 FOCUS_XB 8 2 Non MEGA model FC_A D 6 5 5 6 7 8 E VC-520 BOARD (2/20) 4.6 4.6 LENS DRIVE, EVR 0.1 IRIS DRIVE, HALL AMP : Non MEGA model IRIS DRIVE, HALL BIAS CONTROL : MEGA model 05 R5139 0.7 0.1 A_4.6V_LD ( R1.3/P0.9)<1.2> OP1_BOUT 0.9 OP1_B0.9 OP1_B+ F RB5103 0 DA_STRB 2.8 2.8 Q5101 UP04116G08S0 SENSOR SWITCH -0.9 FC_XB Non MEGA model E FC_RST GND A_IN+ C LENS_TEMP_AD R5165XX R5173 XX 0 C5101 4.7u B CN5101 24P B CLK R5174 XX ZM_A FC_SENS_OUT LD 8 AO3 0.9 IC5101 NJW5210RB1 1 3 5 7 LENS BLOCK AO2 2 4 6 8 A AO1 (1)<1.2> 7 HALL_GAIN 6 REG_GND (0.8)<1.6> 8 5 HALL_OFFSET 7 1 5 2 4 3 3 2 4 1 330 C5106 0.1u XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE ( ):Non MEGA model < >:MEGA model IRIS_BIAS_0.6 0.1 Q5102 2SC5846G0LS0 AMP MEGA model R5138 R5137 1k 10k HALL_GAIN F HALL_REF R5140 22k MEGA model DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-7 VC-520 (2/20) 1 2 3 4 5 6 7 9 8 10 11 12 I_HALL_AD A A C5407 0.047u B 2 4 6 8 RB5401 1k 1 3 5 7 R5411 15k HALL_REF R5410 0 C5409 0.001u B RB5402 470k 1 3 5 7 Q5401 RN1119FV(TL3SONY) IRIS DRIVE R0.3/P0 0 R5414 B OP2_AOUT OP2_A- OP2_A+ 0 0 R5412 OP1_B- OP1_B+ OP1_BOUT R5403 1M R3.9/P4.9 OP1_A+ C5403 4.7u B OP1_A- C5402 0.0047U B OP1_AOUT D5401 MA2S1110G8S0 C5414 XX C5412 XX R5409 2 4 6 8 B C5401 XX HALL_OFFSET C5411 XX C5406 470p B C5404 0.1u B R5405 220k R5404 2200 C C R5406 10k C5405 0.1u B REG_GND C5410 0.01u B C5413 0.0022u B IRIS_COM R5402 0 R5415 47k D D D_2.8V D_2.8V MT_5.0V_LD R0.5/P0 REG_GND E DIR1B E DIR1A 0 0 DIR0A 0.2 2.8 0.2 EN0 0.2 0.2 4.8 EN01 DIR0B C5408 XX EN3 R2.4/P0 IN3 IN4 EN4 PGND OUT4B OUT3B VM23 PGND OUT2B VDD OUT1B 24 23 22 21 20 19 18 17 16 15 14 13 IN1 4 6 8 9 5 7 EN2 VM4 3 IN2 PGND R1.7/P0.1 OUT4A 2 EN1 OUT2A R1.7/P0.1 OUT3A 1 F 10 11 12 4.8 ZOOM_A PGND REG_GND OUT 1A F VM1 IC5401 R2A30406SP-W00T FOCUS/ZOOM MOTOR DRIVE 0 0 R2/P0 R1.7/P4.2 R1.6/P0.1 ZOOM_B 4.8 ZOOM_XB R0.5/P0 ZOOM_XA IRIS_DRIVE_+ IRIS_DRIVE_IRIS_BIAS_+ G G IRIS_HALL_+ IRIS_HALL_FOCUS_XA FOCUS_A FOCUS_XB FOCUS_B VC-520 BOARD (3/20) :Non MEGA model Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E LENS DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE H H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-8 VC-520 (3/20) Ver. 1.1 2008.01 1 2 3 4 6 5 7 9 8 10 11 12 MEGA model IRIS_HALL_IRIS_BIAS_+ A IRIS_HALL_+ R5310 180k IRIS_DRIVE_+ R0.1/ P3.2 C R5301 10 R5302 100 C5302 0.1u C5301 0.22u C5303 1u R5304 10k D5301 MA2S1110G8S0 OP2_A- 0 0 OP2_A+ OP1_BOUT B OP2_AOUT OP1_B- C5314 0.01u HALL_OFFSET HALL_OFFSET I_HALL_AD 0 R5319 OP1_A- R5317 4 OP1_B+ GND 3 0 A_IN+ 2 OP1_AOUT A_OUT A_IN- 1 R5303 100k R5321 C5307 0.033u 0.9 R0.8/P3.4 C5313 0.001u R5315 R3.7/ P3.1 Q5301 2SC5846GOLSO IRIS DRIVE R0.8/P3.4 0.9 D5302 MA2S1110G8S0 R5318 180k XX R5311 39k IC5302 NJM12904V(TE2) IRIS DRIVE B C5310 R5312 180k 5 OP1_A+ 0.9 0.9 6 B_IN- Vcc B_OUT 7 R5316 180k R5320 180k B_IN+ 0.9 4.6 C5304 0.0033u 8 R5313 XX R5305 100k R5314 5600 C5305 0.033u IRIS_DRIVE_- C5309 0.01u A C5311 0.01u R5322 10k R5306 4700 C C5312 XX R5307 33k HALL_REF HALL_REF A_4.6V_LD A_4.6V_LD C5315 4.7u B A_4.6V L5301 10uH D_2.8V MT_5V D_2.8V C5317 XX D REG_GND MT_5.0V_LD D MT_5.0V_LD C5316 XX REG_GND CAM_DD_ON SHUTTER_ON E EN4 IN5 BR4 IN6 EN5 EN6 BR5 IN7 BR6 EN7 OUT1A PS F2 D4 E4 G1 C2 A1 C3 B2 C4 A2 A5 C5 E OUT4A EN2 FOCUS/ZOOM MOTOR DRIVE, IRIS DRIVE OUT4B OUT5A IN2 BR1 EN1 OUT5B IN1 OUT6A OUT6B PGND2 OUT7A PGND2 REG_GND DIR1B EN01 DIR1A EN0 DIR0B DIR0A F C5306 0.1u B MT_5.0V_LD PGND1 PGND1 VM4 VM3 OUT7B G2 F7 F6 G7 G3 G4 D1 D7 A4 G5 C1 E1 G C7 E7 F5 G6 E5 D3 E3 F1 D5 B6 A7 A6 BR2 IC5301 LV8053LG-TLM-E OUT3B VCC F IN3 VM2 REG_GND OUT3A VM1 ZOOM_B EN3 RNF ZOOM_XB BR3 OUT2B RNFS ZOOM_A IN4 OUT2A VLIM FOCUS_B ZOOM_XA OUT1B VREF FOCUS_A FOCUS_XB DGND F3 F4 A3 B3 B5 B4 C6 B7 E6 D6 B1 D2 E2 FOCUS_XA C5308 0.1u R5308 XX G R5309 XX MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E VC-520 BOARD (4/20) LENS DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE H H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-9 VC-520 (4/20) 1 2 4 3 6 5 8 7 10 9 11 A D_3.3V 12 A_2.8V D_2.8V D15 VIN_Y[7] LCD_PDR[7] D26 VIN_Y[6] LCD_PDR[6] C26 B17 VIN_Y[5] LCD_PDR[5] C27 B16 VIN_Y[4] LCD_PDR[4] B26 B15 VIN_Y[3] LCD_PDR[3] B27 A15 VIN_Y[2] LCD_PDR[2] A26 C16 VIN_Y[1] LCD_PDR[1] A27 D16 VIN_Y[0] LCD_PDR[0] D27 C17 VIN_C[7] LCD_PDG/LCD_Y/LCD_SNE[7] D_2.8V D_1.2V 15 C15 D_3.3V A_2.8V 14 13 D_1.2V 16 EVF_BL_ON A A_1.2V C1702 0.001u B X1701 12MHz 4 3 1 2 R1782 XX A_1.2V D_3.3V R1783 XX C1706 0.001u B C A7 PLL1_VCC B7 A6 C1728 0.001u B AA32 PLL1_GND AVDD1 AB32 PLL2_VCC AGND1 V32 B6 PLL2_GND AGND1 W32 E1 PLL3_VCC AGND1 Y32 D1 PLL3_GND AVDD2 V33 G1 PLL4_VCC AVDD2 F1 PLL4_GND AGND2 U35 H1 PLL5_VCC AGND2 Y35 A_1.2V C1705 4.7u B AVDD1 AVDD3 C1723 4.7u B C1714 0.001u B C28 LCD_PDG/LCD_Y/LCD_SNE[5] D29 VIN_C[4] LCD_PDG/LCD_Y/LCD_SNE[4] A28 VIN_C[3] LCD_PDG/LCD_Y/LCD_SNE[3] A29 D18 VIN_C[2] LCD_PDG/LCD_Y/LCD_SNE[2] D28 D17 VIN_C[6] B29 TP_SEL1 LCD_PDG/LCD_Y/LCD_SNE[0] B28 TP_SEL2 VIN_C[0] A16 DOLCE_VCLK_OUT LCD_PDB/LCD_C[7] A18 VIN_CLK_IN LCD_PDB/LCD_C[6] C30 A20 EXT_CAM_CLK_IN LCD_PDB/LCD_C[5] A30 LCD_PDB/LCD_C[4] D31 B30 A17 VIN_FLD LCD_PDB/LCD_C[3] VIN_VD LCD_PDB/LCD_C[2] B31 C20 VIN_HD LCD_PDB/LCD_C[1] C31 C21 MILANO_FLD LCD_PDB/LCD_C[0] D30 B21 MILANO_VD MILANO_FD B20 EXT_CAM_VD A21 HD/SD_IN LCD_CLK_OUT J1 PLL5_GND K1 PLL6_VCC AGND3 W34 L1 PLL6_GND ADVDD AA33 ADVDD AA34 LCD_EXT_CLK_IN LCD_HS ADGND RESET AB33 DVDD AB34 DVSS PLL_MODE2 DVSS AD32 F3 PLL_MODE1 GNDS AC33 D2 PLL_MODE0 GNDS AC34 RREF AB35 PLL_BYPASS H2 PCV E3 TESTMODE R1784 XX C11 STL_DATA[14] AD13 B11 STL_DATA/CCDIN_A[13] DR_VDATA[7] C33 DR_VDATA7 AD12 B12 STL_DATA/CCDIN_A[12] DR_VDATA[6] B33 DR_VDATA6 AD11 D11 STL_DATA/CCDIN_A[11] DR_VDATA[5] C34 AC35 USB_ID U32 D_1.2V DR_VDATA5 AD10 C13 STL_DATA/CCDIN_A[10] DR_VDATA[4] D32 DR_VDATA4 AD9 B13 STL_DATA/CCDIN_A[9] DR_VDATA[3] D34 DR_VDATA3 AD8 AD7 A12 STL_DATA/CCDIN_A[8] DR_VDATA[2] D33 DR_VDATA2 C12 STL_DATA/CCDIN_A[7] DR_VDATA[1] E34 DR_VDATA1 R1724 AD6 D13 STL_DATA/CCDIN_A[6] DR_VDATA[0] D35 DR_VDATA0 100 ± 0.5% AD5 A13 STL_DATA/CCDIN_A[5] AD4 D12 STL_DATA/CCDIN_A[4] DR_GHDATA[3] F33 DR_GHDATA3 AD3 C14 STL_DATA/CCDIN_A[3] DR_GHDATA[2] E33 DR_GHDATA2 DR_GHDATA[1] G33 DR_GHDATA1 DR_GHDATA[0] E32 DR_GHDATA0 DR_GSDATA[3] F34 DR_GSDATA3 DR_GSDATA[2] F32 DR_GSDATA2 R1721 620 ± 0.5% VBUS C1724 1u B C1717 0.001u B AC32 E2 F2 AD2 A14 STL_DATA/CCDIN_A[2] B14 STL_DATA/CCDIN_A[1] D14 STL_DATA/CCDIN_A[0] GND GUARD E V4 TDI_1 U3 TCK_1 DP W35 USB_D+ DM V35 USB_DDA_STRB U33 TDO_1 USB_VBUS_EN U34 C1716 1u B RTCK_1 TRST/BKTGIO_1 V1 TDI_0 T2 TCK_0 U2 TMS_0 U1 TDO_0 AVCC R33 AVSSQ R32 VRH N34 VRL P34 VRN R34 BKTGIO_0 JTAG SEL[3] R2 JTAG SEL[2] ADC/DAC T1 R1 JTAG SEL[1] JTAG SEL[0] V2 VRP N35 AIN P35 AOUT R35 STABLE_RUN BOOT_MODE[2] Y1 BOOT_MODE[1] AA2 BOOT_MODE[0] IC1701 (1/6) ADC H STL_ADDR[9] STL_ADDR[8] STL_ADDR[7] H11 STL_ADDR[6] P32 VREF N33 V_OUT N32 AVCC_ADC2 AG33 AVSS_ADC2 AE33 ADC2_IN1 AM35 ADC2_IN2 AN34 ADC2_IN3 AM34 ADC2_IN4 AM33 AVSS_ADC1 AD35 AVCC_ADC1 AJ32 ADC1_IN1 AL35 ADC1_IN2 AK34 ADC1_IN3 AL34 ADC1_IN4 AK33 ADC1_IN5 AG35 ADC1_IN6 AF35 ADC1_IN7 AK35 2.8 C1720 0.01u B C1715 1u B STL_ADDR[5] DR_VINCK_OUT F35 K10 STL_ADDR[4] DR_SCK54_OUT E35 H14 STL_ADDR[3] STL_ADDR[2] H10 STL_ADDR[1] J11 STL_ADDR[0] DR_GSPILOT GND GUARD H12 J10 DR_GHPILOT H35 G35 R1739 DATA[7] XX DR_VINCK GND GUARD J32 DATA[6] K33 DATA[5] K32 G14 STL_BS[1] DATA[4] L34 J15 STL_BS[0] DATA[3] L33 DATA[2] L32 G15 STL_RAS DATA[1] M33 J16 STL_CAS DATA[0] M32 H15 STL_WE D6 STL_CS1 C7 STL_CS0 C6 STL_CKE A8 STL_CLK_OUT A9 STL_BUS_CTRL D_2.8V TP_SEL2 1 3 5 7 XNS_SW Q1701 UNR31AF00LS0 TOUCH PANEL SELECT SWITCH RB1705 100k RB1703 XX C1726 0.01u B 2.8 RB1707 1M 0 2 4 6 8 F HOTSHOE_ID2 C1725 0.01u B MEGA model G 1 3 5 7 2 4 6 C1729 8 0.1u B C1730 C1731 0.01u 0.01u CCD_FLD B10 CCD_FD TG_HD D10 CCD_HD C9 CKTG_O 256fs_OUT M29 CHCK D9 CKTG_I BCK_OUT M28 B9 CKTG_EXT LRCK_OUT N29 D7 CK_AD SDI0 N28 C8 CLAMP_DUMMY SDI1 P29 D8 CLAMP_OPB SDI2 P28 SDO0 R29 F4 MSHUT_EN SDO1 R28 M1 STRB_ON1 MEGA model RB1706 4700 MEGA model AD34 ADC0_IN1 AH35 ADC0_IN2 AH34 ADATA ADC0_IN3 AJ35 ADC0_IN4 AH33 KEY_AD3 ADC0_IN5 AG34 MEM_SEL1 D_2.8V SHUTTER_ON RB1704 10k RB1701 XX H33 J33 R1745 XX R1746 XX ADA_FCK ADA_BCK ADA_LRCK ADA_SOA0 ADA_SOA1 R1737 XX H ADA_SIA0 KEY_AD0 2 4 6 8 EXT_STROBE N3 STRB_ON2 N4 CAM_V/STRB_ON3 R4 VSUB_CONT DIR0A N7 DIR0A DIR0B K8 DIR0B EN0 M7 BRK0A/EN0 H8 BRK0B DIR1A L9 DIR1A DIR1B J8 DIR1B KEY_AD1 KEY_AD2 MEGA model MEM_SEL2 XX JACK_AD ZOOM_VR_AD AJ33 R1736 LRCK_INOUT PITCH_AD AVSS_ADC0 R1735 H32 C10 TG_VD YAW_AD MEGA model AJ34 MCK_OUT CL1717 I_HALL_AD AL33 ADC0_IN7 K35 L35 R1744 XX LENS_TEMP_AD R1768 1k AG32 AF34 K34 A_2.8V ADC1_IN8 ADC0_IN6 VCLK_OUT TP_Y HOTSHOE_ID1 MEGA model 1 3 5 7 FLD SYSCLK_OUT TP_X AVCC_ADC0 ADC0_IN8 E P33 AVSS_DAC CSUB I DR_GHPILOT DR_GSPILOT/SYS_V SYS_SOUND R1787 XX CXD4218GG-TL CPU DR_GSDATA0 G13 ± 0.5% 1k 2 4 6 8 AA3 DR_GSDATA[0] G11 R1726 ± 0.5% 1 3 5 7 BOOT_MODE[3] Select BOOT_MODE[4] AA1 DR_GSDATA1 STL_ADDR[10] G32 G12 1 3 5 7 G AA4 Boot Mode BOOT_MODE_PORT0 G34 FC_RST_LED C1709 0.001u B AVCC_DAC DR_GSDATA[1] A_2.8V 2 4 6 8 STABLE_RUN P2 P1 STL_ADDR[11] ZM_RST_LED R1725 1k ± 0.5% R1722 10k F R1785 XX 7 5 3 1 T3 USB_VBUS_DISCHG 8 6 4 2 T4 W4 G10 H13 D T34 TMS_1 JTAG W3 USB_VBUS_CHG D25 D24 Y33 Y34 DVDD IC_2401 I/F G2 ADGND STL_DATA[15] I2S I/F CLK_AUDIO_IN A11 CAMIN I/F CLK_SYS_IN C2 PLL B3 C25 XX EN01 L8 BRK1A/EN1 H9 BRK1B P8 DIR2A L7 DIR2B CAM Peripheral XSYS_RST C1703 10p CH USB I/F R1717 1k A25 AA35 LCD_PDEN GND GUARD C IR_LED_ON A32 V34 LCD_VS/SYS_V D A31 D20 D21 XX LCD_PDG/LCD_Y/LCD_SNE[1] VIN_C[1] B19 D_3.3V B R1789 D19 LCD I/F R1781 XX LCD_PDG/LCD_Y/LCD_SNE[6] VIN_C[5] C18 A19 C19 VIN I/F B C29 I IC1701 (2/6) CXD4218GG-TL CPU ZM_RST J FC_RST K7 BRK2A/EN2 J7 BRK2B A5 SENS1A B5 SENS1B AE32 SENS0 AF32 SENS2 AE35 FG1A AE34 FG1B J REG_GND MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710EDVD810/DVD810E K K VC-520 BOARD (5/20) CPU (SIGNAL PROCESS 1) XX MARK:NO MOUNT NO MARK:REC/PB MODE L L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-10 VC-520 (5/20) 1 3 2 5 4 6 9 8 7 10 11 12 14 13 15 16 A A AR11 XMS_ACC_LED WD_DIS R1846 H21 GPIO_S[11] EXIO_ADDR[11] G21 GPIO_S[10] EXIO/CF_ADDR[10] AM8 H22 GPIO_S[9] EXIO/CF_ADDR[9] AP11 SHOE_ON G22 GPIO_S[8] EXIO/CF_ADDR[8] AR10 FM_PWR_ON H23 GPIO_S[7] EXIO/CF_ADDR[7] AN9 AA8 EMC_ADDR[25] G23 GPIO_S[6] EXIO/CF_ADDR[6] AN11 Y7 EMC_ADDR[24] H24 GPIO_S[5] EXIO/CF_ADDR[5] AP9 W8 EMC_ADDR[23] G24 GPIO_S[4] W9 EMC_ADDR[22] XX PANEL_O/C PANEL_NOR/REV XX R1847 R1871 XX XVBUS_DET START/STOP REG_GND CAM_DD_ON EXIO/CF_ADDR[4] MEGA model DVD410E/DVD810/DVD810E B AN8 H25 GPIO_S[3] EXIO/CF_ADDR[3] G25 GPIO_S[2] EXIO/CF_ADDR/ATA_ADDR[2] AM11 H26 GPIO_S[1] EXIO/CF_ADDR/ATA_ADDR[1] AM10 G26 GPIO_S[0] EXIO/CF_ADDR/ATA_ADDR[0] AM9 U9 EMC_ADDR[21] 2 4 6 8 ATA_A2 R9 EMC_ADDR[20] ATA_A1 AB8 EMC_ADDR[19] RB1801 ATA_A0 T9 EMC_ADDR[18] AA7 EMC_ADDR[17] AR9 82 1 3 5 7 XATA_CS0 DVD410E/DVD810/DVD810E R1850 FM_BS C 120 EXIO/CF_DATA/ATA_DATA[15] AJ9 MS_BS EXIO/CF_DATA/ATA_DATA[14] AM12 AE28 MS_BIO[3] EXIO/CF_DATA/ATA_DATA[13] AJ10 FB1803 AE29 FM_BIO3 R1851 XX R1857 XX FM_BIO2 R1852 XX R1858 XX AF28 MS_BIO[2] EXIO/CF_DATA/ATA_DATA[12] AJ8 FM_BIO1 R1853 XX R1859 XX AG28 MS_BIO[1] EXIO/CF_DATA/ATA_DATA[11] AH10 FM_BIO0 R1854 XX R1860 XX AH28 MS_BIO[0] EXIO/CF_DATA/ATA_DATA[10] AH13 AG29 MS_CLK AM31 MSX_BS R1855 FM_CLK 120 EXIO/CF_DATA/ATA_DATA[9] AH8 EXIO/CF_DATA/ATA_DATA[8] AJ14 EXIO/CF_DATA/ATA_DATA[7] AH9 XX R1863 XX R1868 XX R1864 XX R1869 XX MSX_BIO[3] AN30 AN33 AM30 AR32 W1 IRIS_COM R1838 47k Data MSX/MS I/F AN12 MSX_BIO[2] EXIO/CF_DATA/ATA_DATA[1] AH14 MSX_BIO[1] EXIO/CF_DATA/ATA_DATA[0] AH12 RB1804 7 5 3 1 MSX_BIO[0] MSX_CLK CF_CE2/ATA_CS[1] TPU0_OUT TPU1_OUT AL2 AK2 EXIO/CF/ATA_IORD EXIO/CF/ATA_IOWR AN4 CF_REG/ATA_DMACK AM3 Y2 TPU4_OUT CF_INPACK/ATA_DMARQ AK1 CF_WAIT/ATA_IORDY AJ4 SIRCS_SIG Y3 SIR_RXD AR12 I2C_SCK AR13 I2C_SDA R1842 AM4 TPU3_OUT SIR_TXD 8 6 4 2 EMC_ADDR[14] Y10 EMC_ADDR[14] ATA_D12 EMC_ADDR[13] W11 EMC_ADDR[13] ATA_D11 EMC_ADDR[12] T11 EMC_ADDR[12] ATA_D10 EMC_ADDR[11] V10 EMC_ADDR[11] ATA_D9 EMC_ADDR[10] V9 EMC_ADDR[10] ATA_D8 EMC_ADDR[9] T10 EMC_ADDR[9] ATA_D7 EMC_ADDR[8] Y11 EMC_ADDR[8] ATA_D6 EMC_ADDR[7] Y9 EMC_ADDR[7] ATA_D5 EMC_ADDR[6] W12 EMC_ADDR[6] ATA_D4 EMC_ADDR[5] W10 EMC_ADDR[5] ATA_D3 EMC_ADDR[4] V11 EMC_ADDR[4] ATA_D2 EMC_ADDR[3] U11 EMC_ADDR[3] ATA_D1 EMC_ADDR[2] V12 EMC_ADDR[2] ATA_D0 EMC_ADDR[1] U12 EMC_ADDR[1] EMC_ADDR[0] AA9 180 EMC_ADDR[0] 180 EMC_DATA[31] AG18 EMC_DATA[31] EMC_DATA[30] AF20 EMC_DATA[30] EMC_DATA[29] AJ19 EMC_DATA[29] EMC_DATA[28] AE19 EMC_DATA[28] EMC_DATA[27] AH18 EMC_DATA[27] EMC_DATA[26] AF19 EMC_DATA[26] ATA_DMARQ EMC_DATA[25] AJ20 EMC_DATA[25] ATA_IORDY EMC_DATA[24] AE18 EMC_DATA[24] ATA_INTRQ EMC_DATA[23] AF18 EMC_DATA[23] EMC_DATA[22] AH19 EMC_DATA[22] EMC_DATA[21] AH20 EMC_DATA[21] XATA_DIOR R1843 180 XATA_DIOW R1841 180 XATA_DMACK D_2.8V R1803 1k 2 4 6 RB1806 10k 1 3 5 7 CF_RDY/ATA_TRQ AM2 CF_BVD2/ATA_DASP AK4 CF_BVD1/ATA_PDIAG AN3 CF_WP/ATA_IOCS16 AL3 REG_GND EMC_DATA[20] AE20 EMC_DATA[20] CF_Reset/ATA_RESET AL4 XATA_RESET EMC_DATA[19] AG19 EMC_DATA[19] EXIO_DIR AN6 XQUICKREC_LED EMC_DATA[18] AH26 EMC_DATA[18] CF_DRV AK3 XPHOTO_LED EMC_DATA[17] AJ21 EMC_DATA[17] EMC_DATA[16] AD18 EMC_DATA[16] RB1807 22 EXIO_CS0 AM5 EMC_DATA[15] AD19 EMC_DATA[15] JOG0_A/TPU0_INA EXIO_CS1 AP5 EMC_DATA[14] AH25 EMC_DATA[14] AH1 JOG0_B/TPU0_INB EXIO_WAIT AN5 EMC_DATA[13] AG20 EMC_DATA[13] AJ2 JOG1_A/TPU1_INA AJ1 JOG1_B/TPU1_INB AH2 XFM_IN DVD410E/DVD810/DVD810E EXIO_IRQ AP6 EMC_DATA[12] AJ24 EMC_DATA[12] EXIO_DREQ AM6 EMC_DATA[11] AH22 EMC_DATA[11] EXIO_DACK AR6 EMC_DATA[10] AG26 EMC_DATA[10] EMC_DATA[9] AG21 EMC_DATA[9] F UART0_TXD EMC_DATA[8] AH24 EMC_DATA[8] UART0_RXD PCI_AD[31] AR26 EMC_DATA[7] AG25 EMC_DATA[7] T25 UART0_CTS PCI_AD[30] AM22 EMC_DATA[6] AH21 EMC_DATA[6] T26 UART0_RTS PCI_AD[29] AP26 EMC_DATA[5] AF26 EMC_DATA[5] PCI_AD[28] AN22 EMC_DATA[4] AJ23 EMC_DATA[4] R27 UART1_TXD PCI_AD[27] AN27 EMC_DATA[3] AJ26 EMC_DATA[3] XCS_LCD T27 UART1_RXD PCI_AD[26] AP22 EMC_DATA[2] AH23 EMC_DATA[2] XCS_IC_2401 U27 UART1_CTS PCI_AD[25] AM27 EMC_DATA[1] AJ25 EMC_DATA[1] XCS_IC_2801/IC_2901 U26 UART1_RTS PCI_AD[24] AR22 EMC_DATA[0] AJ22 EMC_DATA[0] PCI_AD[23] AR27 AM23 EMC_XOE AG15 EMC_XOE UART U25 U24 E F DDR_XWE T8 DDR_XCS[1] V7 DDR_XCS[0] V8 DDR_XRAS U8 DDR_CKE1 U7 R1829 100k UART2_SI H27 UART2_RXD PCI_AD[21] AN23 EMC_XWE AF17 EMC_XWE H28 UART2_CTS PCI_AD[20] AP23 AG11 EMC_XCS[2] J27 UART2_RTS PCI_AD[19] AP27 EMC_XCS[1] AF10 EMC_XCS[1] DDR_DQS[3] AC8 PCI_AD[18] AR23 EMC_XCS[0] AG10 EMC_XCS[0] DDR_DQS[2] AB7 PCI_AD[17] AN28 EMC_XDQM[3] AH15 EMC_XDQM[3] PCI_AD[16] AM24 EMC_XDQM[2] AD17 EMC_XDQM[2] PCI_AD[15] AM28 EMC_XDQM[1] AH16 EMC_XDQM[1] PCI_AD[14] EMC_XDQM[0] AE17 EMC_XDQM[0] AN26 EMC_XRAS AG16 EMC_XRAS PCI_AD[12] AP28 EMC_XCAS AE16 EMC_XCAS EMC_CKE AJ15 EMC_CKE A23 SSP0_CLK PCI_AD[11] AM26 C23 SSP0_FRM PCI_AD[10] AR28 D23 SSP0_TXD PCI_AD[9] AR25 EMC_CLK0_OUT W25 EMC_CLK0_OUT B23 SSP0_RXD PCI_AD[8] AN29 EMC_CLK0_IN W26 EMC_CLK0_IN PCI_AD[7] AP25 EMC_CLK1_OUT Y25 EMC_CLK1_OUT EMC_CLK1_OUT Y26 EMC_CLK1_IN XSCK_IC_4201 G18 SSP1_CLK PCI_AD[6] AN25 XCS_IC_4201 H19 SSP1_FRM PCI_AD[5] AM29 TXD_TO_IC_4201 G19 SSP1_TXD PCI_AD[4] AM25 RXD_TO_IC_4201 H18 SSP1_RXD PCI_AD[3] AR29 PCI_AD[2] AP24 XFR_SCK A22 SIO0_SCK PCI_AD[1] AP29 XCS_EX D22 SIO0_SCS PCI_AD[0] AR24 FR_SI B22 SIO0_TXD FR_SO C22 SIO0_RXD CAM_SO AG17 EMC_RDY0 AH17 EMC_XRST PCT_BE[3] PCT_BE[2] AM17 J17 SIO1_SCK PCT_BE[1] AN16 G17 SIO1_SCS PCT_BE[0] AM16 PCI_PAR AM15 AF16 EMC_XRESET_OUT PCI_FRM AN13 CL1804 EMC_XRESET_OUT SIO1_RXD E5 F_CE0 XBB_SCK M18 SIO2_SCK PCI_TRDY AN14 E4 F_XAVD L19 SIO2_SCS PCI_SERR AM13 K4 F_XRP BB_SO M19 SIO2_TXD PCI_DEVSEL AM14 L18 SIO2_RXD PCI_IDSEL AN15 PCI_PERR AN17 CH_SCK L16 SIO3_SCK CH_CS L17 SIO3_SCS PCI_REQFS0 AM20 CH_SO M17 SIO3_TXD PCI_GNTTS0 AP17 CH_SI K16 SIO3_RXD PCI_REQFS1 AN20 PCI_GNTTS1 AP18 PCI_REQFS2 AN18 SIO SIO1_TXD Control IC1701 (3/6) CXD4218GG-TL CPU K DQS DDR REG_GND J AM18 PCI_REQFS3 AR18 PCI_GNTTS3 AP21 PCI_STOP AR19 PCI_IRDY AR21 PCI_RESET H I K17 PCI_GNTTS2 AG7 CL1805 H17 BB_SI M8 IC1701 (4/6) CXD4218GG-TL CPU CL1802 AP15 N8 DDR_DQS[0] TEMP CL1803 PCI I/F CAM_SCK EMC_RDY0 DDR AN24 PCI_AD[13] DDR_DQS[1] DQM UART3_RTS EMC_Control K27 EMC UART3_CTS Clock UART3_RXD SSP H UART3_TXD J25 J26 EMC XHOT_STBY K26 G NAND UART3_SI DDR PCI_AD[22] Clock UART2_TXD Address/Data G27 UART3_SO J D UART2_SO G I C XATA_CS1 AM1 CF_OE CF_WE TPU2_OUT Y4 33 R1840 AL1 U4 PANEL_BL_ON 2 4 6 8 EMC_ADDR[15] ATA_D13 RB1805 W2 REG_GND E AH11 EXIO/CF_DATA/ATA_DATA[3] CF_CE1/ATA_CS[0] V3 IRIS_PWM EXIO/CF_DATA/ATA_DATA[4] AJ12 FB1802 R1845 XX AJ11 EXIO/CF_DATA/ATA_DATA[2] Control R1844 120 Non MEGA model AM32 EXIO/CF_DATA/ATA_DATA[5] 1 3 5 7 33 Y8 R1830 5600 XX R1867 AJ13 8 6 4 2 EMC_ADDR[16] EMC_ADDR[15] 1 3 5 7 R1862 EXIO/CF_DATA/ATA_DATA[6] 33 RB1803 2 4 6 8 XX MSX_CLK R1801 XX MSX_BIO[4] PWM MSX_BIO0 MSX_BIO[5] SIRCS MSX_BIO1 AP32 AN31 EXIO/CF/ATA I/F XX R1870 MSX_BIO2 MSX_BIO[6] FB1801 R1866 MSX_BIO3 D 120 AP31 I2C R1865 MSX_BIO[7] JOG MSX_BS AN32 RB1802 U10 ATA_D14 8 R1873 XX ATA_D15 7 5 3 1 FB1804 R1872 XX REG_GND 33 8 6 4 2 7 5 3 1 DDR_Address AN7 DDR_Data EXIO_ADDR[12] DDR_Control AN10 GPIO_S[12] DDR AM7 EXIO_ADDR[13] CL1801 B AP10 EXIO_ADDR[14] GPIO_S[13] EMC EXIO_ADDR[15] GPIO_S[14] EMC_Address GPIO_S[15] G20 J21 EMC_Data VST_C_RESET MEGA model J20 H20 Address XBB_RST GPIO MS_PWR_ON AP19 PCI_CLKEN AN19 PCI_CLKIN AR16 PCI_CLKOUT AR17 PCI_CLKRUN AM19 PCI_INTA AR20 PCI_INTB AM21 PCI_INTC AP20 PCI_INTD AN21 K VC-520 BOARD (6/20) Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E L CPU (SIGNAL PROCESS 2) XX MARK:NO MOUNT L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-11 VC-520 (6/20) 1 3 2 4 6 5 7 9 8 10 11 12 A_2.8V R2001 XX A_2.8V A_2.8V D_1.2V R2011 XX D_1.2V D_1.2V R2012 XX D_1.8V A D_1.8V A R2013 XX D_1.8V D_1.8V C2042 2.2u B C2043 2.2u B C2045 4.7u B R2014 XX D_2.8V D_2.8V R2015 XX D_2.8V D_2.8V C2039 2.2u B C2038 2.2u B D_1.8V IC1701 (5/6) CXD4218GG-TL IC1701 (6/6) D_1.2V B D_1.2V D_2.8V C2006 0.001u B C ALGCOREVDDT S_VDDQ U28 AD4 ALGCOREVDDT S_VDDQ U29 AE3 ALGCOREVDDT S_VDDQ V28 AE4 ALGCOREVDDT S_VDDQ V29 AN2 ATAIOVDD S_VDD Y28 AP3 AD3 CXD4218GG-TL CPU CPU ATAIOVDD S_VDD AP4 ATAIOVDD F_VCCQ AA28 AR4 ATAIOVDD F_VCCQ AA29 C2031 0.001u B C2032 0.001u B Y29 C2033 0.001u B D3 COREVDD COREGND D4 COREVDD COREGND D5 COREVDD COREGND L27 K20 COREVDD COREGND M35 K18 K19 L4 COREVDD COREGND T28 L20 COREVDD COREGND T29 L28 COREVDD COREGND T32 M3 COREVDD COREGND T33 M4 COREVDD COREGND V27 W27 COREVDD COREGND W7 W28 COREVDD COREGND W33 AR5 ATAIOVDD F_VCC AC28 AR7 ATAIOVDD F_VCC AC29 D_2.8V M34 AUDIOVDD EMCIOVDD V24 W29 COREVDD COREGND AB1 A_2.8V AF33 AVCC_PI EMCIOVDD V25 Y27 COREVDD COREGND AB2 AD33 AVSS_PI EMCIOVDD V26 AA27 COREVDD COREGND AB3 J2 CAMCOREVDDT EMCIOVDD W24 AC2 COREVDD COREGND AB4 J3 CAMCOREVDDT EMCIOVDD AJ16 AC3 COREVDD COREGND AB28 J4 CAMCOREVDDT AB29 G3 C2002 0.001u B D_1.2V D_2.8V D_1.8V D D_1.8V C2010 0.001u B C2003 0.001u B D_1.2V EMCIOVDD AJ17 CAMINIOVDD EMCIOVDD AJ18 G4 CAMINIOVDD I2CIOVDD AR15 H3 CAMINIOVDD GCIOVDD G9 H4 CAMINIOVDD GCCOREVDD L3 R8 DDRVDDQ GCCOREGND J9 T7 DDRVDDQ MSIOVDD AF29 AD7 DDRVDDQ MSXIOVDD AP33 AD8 DDRVDDQ NICEIOVDD H34 P7 DDRVDD NICEIOVDD J34 R7 DDRVDD NICEIOVDD J35 AE7 D_2.8V R2016 XX C2013 0.001u B D_2.8V R2017 XX C2012 0.001u B D_1.2V D_1.8V C2019 0.1u B C2014 0.001u C2015 0.001u C2017 0.001u B B AC4 COREVDD COREGND AD28 COREVDD COREGND D_2.8V AF7 COREVDD COREGND AD2 A_2.8V AF8 COREVDD COREGND AD29 D_1.2V D_2.8V AP7 COREVDD COREGND AE2 AP30 COREVDD COREGND AE27 A2 AF27 COREGND COREGND A3 COREGND COREGND AH3 A4 COREGND COREGND AH4 A10 COREGND COREGND AH7 A33 COREGND COREGND AH29 AG27 A34 COREGND COREGND AH32 AH27 D_2.8V DDRVDD PCIIOVDD DDRVDD PCIIOVDD B1 COREGND COREGND AF2 DDRIOVDD PCIIOVDD AJ27 B2 COREGND COREGND AJ7 AF3 DDRIOVDD PCIIOVDD AP14 B4 COREGND COREGND AJ28 AF4 DDRIOVDD PCIIOVDD AR14 AJ29 AG1 DDRIOVDD PLLTOPCOREVDDT AG2 DDRIOVDD PLLTOPCOREVDDT M2 AG3 DDRIOVDD USBIOVDD T35 AG4 DDRIOVDD PERIIOVDD1 N1 AE1 DLL1_VCC PERIIOVDD1 N2 AF1 DLL1_GND PERIIOVDD2 P3 L2 DLL2_VCC PERIIOVDD2 P4 AD1 DLL2_GND PERIIOVDD2 R3 K28 DRIOVDD PERIIOVDD3 A24 K29 DRIOVDD PERIIOVDD3 B24 L29 DRIOVDD PERIIOVDD3 C24 B32 LCDIOVDD VINIOVDD B18 C32 LCDIOVDD VINIOVDD G16 J28 LCDIOVDD VINIOVDD H16 J29 LCDIOVDD AE9 AF9 B8 COREGND COREGND B25 COREGND COREGND AK32 B34 COREGND COREGND AL32 D_3.3V B35 COREGND COREGND AN1 C1 COREGND COREGND AN35 C3 COREGND COREGND AP1 C4 COREGND COREGND D_2.8V C2025 0.001u B D_2.8V AP2 C5 COREGND COREGND AP8 C35 COREGND COREGND AP12 G7 COREGND COREGND AP13 G8 COREGND COREGND AP16 G28 COREGND COREGND AP34 G29 COREGND COREGND AP35 H7 COREGND COREGND AR2 H29 COREGND COREGND AR3 A1 J18 COREGND COREGND AR8 MPGCOREVDDT A35 J19 COREGND COREGND AR30 MPGCOREVDDT AR1 K2 COREGND COREGND AR31 AG8 MPGCOREVDDT AR35 K3 COREGND COREGND AR33 AG9 MPGCOREVDDT K9 COREGND COREGND AR34 C2026 0.001u B D AJ3 A_1.2V C2024 0.001u B C AC7 AE8 AC1 E C2034 0.001u B B E F F REG_GND G G VC-520 BOARD (7/20) CPU (POWER SUPPLY) H XX MARK:NO MOUNT H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-12 VC-520 (7/20) 1 3 2 4 6 5 7 9 8 10 11 12 A A Note: IC2101 is not supplied, but this included in VC-520 complete board. C EMC_DATA[4] EMC_DATA[8] EMC_DATA[7] EMC_DATA[10] EMC_DATA[3] EMC_ADDR[8] EMC_DATA[5] EMC_ADDR[7] EMC_DATA[6] EMC_ADDR[11] EMC_DATA[4] EMC_DATA[8] EMC_DATA[14] EMC_DATA[7] EMC_DATA[13] EMC_DATA[10] EMC_DATA[9] EMC_CKE EMC_DATA[9] EMC_DATA[11] EMC_DATA[12] EMC_DATA[14] EMC_DATA[18] EMC_DATA[16] EMC_DATA[13] EMC_ADDR[13] D EMC_ADDR[4] EMC_ADDR[13] EMC_ADDR[4] EMC_DATA[15] EMC_DATA[17] EMC_DATA[21] EMC_DATA[11] EMC_ADDR[6] EMC_DATA[12] EMC_DATA[29] EMC_DATA[14] EMC_DATA[18] EMC_DATA[12] EMC_DATA[16] EMC_DATA[13] EMC_XDQM[1] EMC_DATA[15] EMC_DATA[30] EMC_DATA[17] EMC_DATA[31] EMC_DATA[21] EMC_DATA[28] EMC_DATA[27] EMC_DATA[11] EMC_DATA[10] EMC_ADDR[12] EMC_ADDR[3] EMC_ADDR[0] EMC_ADDR[8] EMC_ADDR[15] E EMC_ADDR[6] EMC_ADDR[9] EMC_ADDR[2] EMC_ADDR[14] EMC_ADDR[1] EMC_ADDR[12] EMC_ADDR[3] EMC_ADDR[0] EMC_ADDR[8] EMC_ADDR[15] EMC_ADDR[6] EMC_ADDR[9] EMC_ADDR[2] EMC_ADDR[14] EMC_ADDR[1] EMC_DATA[19] EMC_DATA[25] EMC_DATA[20] EMC_DATA[28] EMC_DATA[29] EMC_DATA[30] EMC_DATA[23] EMC_DATA[22] EMC_DATA[27] EMC_DATA[24] EMC_DATA[31] EMC_ADDR[5] EMC_ADDR[11] EMC_ADDR[7] EMC_ADDR[10] EMC_ADDR[5] EMC_DATA[26] C2105 0.1u B EMC_DATA[26] EMC_DATA[25] EMC_DATA[20] EMC_DATA[25] EMC_DATA[28] EMC_DATA[9] EMC_DATA[29] EMC_DATA[8] EMC_DATA[30] EMC_DATA[23] EMC_DATA[22] EMC_DATA[27] EMC_DATA[24] EMC_DATA[31] EMC_DATA[24] EMC_DATA[26] EMC_XDQM[3] EMC_ADDR[11] EMC_XWE EMC_ADDR[7] EMC_XCAS EMC_ADDR[10] EMC_XCAS EMC_XDQM[0] F EMC_DATA[19] EMC_XWE EMC_XDQM[2] EMC_XOE EMC_XRAS EMC_XCAS EMC_XCS[1] EMC_XDQM[0] EMC_XWE EMC_XWE CL2101 EMC_XDQM[2] T3 T13 U1 S_BA1 S_DQ9 S_BA0 S_DQ8 S_Vddq S_Vddq S_Vssq S_Vssq DNU DNU DNU NC NC NC S_DQ0 DNU S_Vdd S_A0 S_A9 S_A1 S_A5 S_A3 NC NC S_DQ15 S_DQ2 S_A4 S_DQ1 S_A8 S_A10 S_A7 S_DQ21 S_A11 S_DQ20 NC S_DQ17 S_DQ14 S_DQ16 S_DQ13 S_DQM0 NC NC S_DQ3 S_CKE S_A6 S_DQ22 S_DQ29 S_DQ23 NC S_DQ19 S_DQ12 S_DQ18 NC S_Vddq S_DQM1 S_Vssq S_DQ30 S_DQ5 S_DQ31 S_DQ4 S_DQ28 NC S_DQ27 S_DQM2 S_DQ11 S_Vssq S_DQ10 S_Vddq DNU S_Vssq S_Vddq S_Vssq S_Vssq S_Vddq S_Vddq S_DQ7 S_DQ26 S_DQ6 S_DQ25 NC S_Vddq NC S_Vssq S_DQ24 S_CLK S_DQM3 S_Vssd S_A12 S_/WE NC S_/CAS S_Vdd S_/RAS S_Vssd S_/CS DNU DNU EMC_DATA[0] EMC_ADDR[0] EMC_ADDR[1] EMC_ADDR[3] EMC_DATA[2] EMC_DATA[1] EMC_ADDR[9] EMC_ADDR[13] EMC_ADDR[10] EMC_DATA[21] EMC_DATA[20] EMC_DATA[17] EMC_DATA[16] EMC_ADDR[1] EMC_ADDR[3] EMC_ADDR[6] EMC_XDQM[0] C2103 0.1u B EMC_DATA[3] EMC_DATA[22] EMC_DATA[23] EMC_ADDR[8] EMC_ADDR[12] EMC_DATA[19] EMC_DATA[18] EMC_ADDR[2] EMC_ADDR[5] EMC_DATA[5] EMC_DATA[4] EMC_ADDR[10] EMC_XDQM[2] EMC_ADDR[14] EMC_ADDR[4] EMC_ADDR[7] EMC_ADDR[15] EMC_DATA[7] EMC_ADDR[0] EMC_DATA[6] EMC_ADDR[15] EMC_ADDR[11] EMC_ADDR[14] EMC_XOE EMC_XWE EMC_DATA[2] EMC_DATA[3] EMC_DATA[11] DNU DNU DNU NC DNU NC DNU NC F_Vsso NC F_Vcc NC NC F_Vsso NC NC NC F_A9 NC NC F_A13 NC NC NC F_DQ0 F_A1 NC F_A3 F_Vcc F_Vsso F_A6 DNU NC F_DQ15 F_Vcc NC F_DQ7 F_A8 F_Vccq F_A12 NC NC NC F_A2 NC F_A5 F_DQ8 NC NC NC NC F_/CEo NC F_DQ14 F_A10 T9 T10 T11 T12 U3 U4 U5 U6 U7 U8 U9 U10 U11 U12 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 W1 W2 W3 W12 W13 W14 EMC_DATA[6] EMC_ADDR[4] NC DNU DNU F_A14 F_DQ6 F_A4 F_Vccq F_A7 F_DQ12 F_/RP F_Vccq T8 EMC_DATA[5] EMC_DATA[15] EMC_DATA[2] S_Vssd EMC_ADDR[2] F_A15 F_Vccq T7 EMC_DATA[3] EMC_DATA[1] S_A2 DNU DNU NC F_A0 F_/AVD F_CLK NC F_DQ13 F_A11 NC F_DQ5 F_/OEo F_DQ4 F_DQ10 F_/WEo F_DQ2 F_DQ9 F_DQ3 F_RDY F_DQ11 F_INTo B C2101 0.1u B EMC_DATA[0] C EMC_DATA[15] EMC_DATA[7] C2102 0.1u B EMC_DATA[8] EMC_XCS[0] D CL2104 EMC_DATA[14] EMC_DATA[6] EMC_DATA[12] EMC_DATA[1] F_DQ1 T6 EMC_DATA[2] S_Vdd DNU DNU T5 EMC_DATA[1] EMC_ADDR[5] DNU DNU EMC_XRAS EMC_CLK1_OUT P11 R6 R7 R8 R9 R10 R11 T4 CL2103 DNU P10 P9 P8 P7 N10 F9 F8 F7 F6 E10 E9 E8 E7 E6 D11 D10 D9 D8 D7 D6 D5 C12 C11 C10 C9 C8 C7 C6 C5 C4 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 A14 A13 A12 A3 A2 EMC_ADDR[9] EMC_DATA[0] DNU L5 L10 L11 L12 L13 L14 M2 M3 M4 M5 M10 M11 M12 M13 N2 N3 N4 N5 N11 N12 N13 P2 P3 P4 P5 P6 P12 P13 R2 R3 R4 R5 R12 R13 T2 EMC_DATA[0] EMC_DATA[0] S_Vdd L4 C2106 0.1u B R2105 XX EMC_CLK1_OUT S_Vssq NC K5R1213ACB-DK75T 512M OneNAND FLASH L3 EMC_CLK1_OUT EMC_CLK1_OUT DNU IC2101 (2/2) C2104 0.1u B L2 EMC_CLK0_OUT B EMC_CLK0_OUT DNU K1 K2 K3 K4 K5 K10 K11 K12 K13 K14 L1 J14 J13 J12 J11 J10 J5 J4 J3 J2 J1 H13 H12 H11 H10 H5 H4 H3 H2 G13 G12 G11 G10 G5 G4 G3 G2 F13 F12 F11 F10 F5 F4 F3 F2 E13 E12 E11 E5 E4 E3 E2 D13 D12 D4 D3 D2 C14 C13 C3 C2 C1 B14 B2 B1 A1 R2104 22 EMC_CLK0_IN DNU U2 U13 U14 IC2101 (1/2) K5R1213ACB-DK75T 512M SDRAM REG_GND EMC_DATA[13] EMC_DATA[5] EMC_DATA[4] E EMC_DATA[10] EMC_DATA[9] EMC_RDY0 EMC_XRESET_OUT EMC_XCS[0] EMC_CLK0_OUT EMC_XRAS EMC_ADDR[12] F R2106 XFLASH_RST EMC_XOE 1k C2107 XX EMC_XCS[1] EMC_XDQM[1] EMC_XDQM[3] EMC_CKE EMC_XRAS EMC_RDY0 EMC_XRESET_OUT EMC_XCS[1] EMC_XCS[1] CL2102 EMC_XDQM[1] D_1.8V D_1.8V EMC_XDQM[3] EMC_CKE C2109 4.7u B EMC_XRAS D_1.8V EMC_RDY0 R2108 XX C2112 47u 4V TA R2107 XX D_1.8V C2108 XX D_1.8V EMC_XRESET_OUT D_1.8V G G EMC_XRESET_OUT EMC_RDY0 EMC_CKE 2 4 6 8 1 3 5 7 VC-520 BOARD (8/20) RB2102 47k SDRAM, OneNAND FLASH H XX MARK:NO MOUNT H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-13 VC-520 (8/20) 2 1 4 3 6 5 7 9 8 10 12 11 14 13 MPXOUT2 FB4201 D_1.2V A_2.8V L4203 XX A_2.8V A_2.8V SDAT WP1_OP MSPDSH APCLOAD A A_2.8V A_2.8V DEW_AD ACCS_LED SLEEP_SW LD_EN JTDI_J JRTCK_J FDQ1 FEA1 FEA3 FDQ0 FEA18 FDQ13 FDQ14 FEA15 FEA12 ATA_D4 ATA_D15 ATA_D1 ATA_D13 ATA_D10 ATA_DMARQ XATA_DMACK SDDQ0 SDDQ1 XATA_CS0 SDA8 SDDQ12 XSDRAS SDA7 SDA11 EJECT_DET TXD_TO_IC_4201 MNT6 SDA2 FGINI FRDR SLSTRD1 A 16 15 D_1.2V D_1.2V_C D_2.8V_P C4246 1u B C4247 XX D_2.8V FB4203 D_2.8V C4248 1u B REG_GND R4240 22 AVDD9 L4 K4 J4 H4 G4 F4 E4 D4 C4 C5 ATDD5 AVSS15 ATDD8 AVDD15 FEA2 FEA4 FEA13 FDQ7 FDQ6 VDDE FEA5 FDQ12 FDQ10 FDQ11 VSS FDQ2 VDDE FEA7 FOEZ FPGMZ FCE1Z FDQ5 FEA8 FEA0 FEA10 VDDI VDDE TRST FEA14 XRST JTMS ATXRST ATDD6 PB6 VDDE PB3 VSS PL3 VDDI PL0 VDDE PD4 XIOW PD0 WP3 VSS WSP_WAP XDASP LPPI VDDE SDDQ15 AVSS14 SDDQ2 AVSS12 SDDQ3 AVDD13 WBVRB SDDQ10 AVDD11 VSS ADIO2 SDDQ9 SWRF C8 BOTM2 N3 XSDCAS AVSS9 SDA12 ADIO1 AVSS4 G3 PI3 AVDD4 F3 VDDI AVDD2 E3 VSS AVDD1 D3 VDDE SKEWR SPDW SPCW SDDQ5 SDDQ13 XATA_CS1 XATA_RESET ATA_A0 ATA_A1 XATA_DIOR ATA_D14 ATA_D12 ATA_D3 ATA_D5 ATA_D8 R4206 XX XATA_RESET ATA_D15 ATA_D14 ATA_D13 ATA_D12 ATA_D11 ATA_D10 ATA_D9 ATA_D8 ATA_D7 ATA_D6 ATA_D5 ATA_D4 ATA_D3 ATA_D2 ATA_D1 ATA_D0 ATA_D15 ATA_D14 ATA_D13 ATA_D12 ATA_D11 ATA_D10 ATA_D9 ATA_D8 ATA_D7 ATA_D6 ATA_D5 ATA_D4 ATA_D3 ATA_D2 ATA_D1 ATA_D0 ATA_DMARQ XATA_DIOR XATA_DIOW ATA_IORDY XATA_DMACK ATA_INTRQ ATA_A2 ATA_A1 ATA_A0 ATA_DMARQ XATA_DIOR XATA_DIOW ATA_IORDY XATA_DMACK ATA_INTRQ ATA_A2 ATA_A1 ATA_A0 FEA13 FDQ7 FDQ6 FDQ12 FDQ11 FDQ2 FEA7 XATA_CS0 XATA_CS1 FOEZ XATA_CS0 XATA_CS1 FCE1Z FFDR FRDR TFDR TRDR FMPWN_OUT0 FMPWN_OUT1 DRV_SEL SLSTFD1 SLSTRD1 SLSTFD2 SLSTRD2 FGINI SV_FS4SV XMUTE0 XMUTE1 DRV_SEL SLSTFD1 SLSTRD1 SLSTFD2 SLSTRD2 FGINI SV_FS4SV XMUTE0 XMUTE1 G C4249 0.01u XIC_4201_RESET JTMS_J R4257 1k XMUTE1 XIC_4201_RESET_A LPP2 LPP2 JL4212 BRMOD SCS FB4206 R4256 WP3_OP WFPDSH 22 LPP C4220 XX C4239 XX BH2 FDQ0 FDQ1 FDQ2 FDQ3 FDQ4 FDQ5 FDQ6 FDQ7 FDQ8 FDQ9 FDQ10 FDQ11 FDQ12 FDQ13 FDQ14 FDQ15 FEA0 FEA1 FEA2 FEA3 FEA4 FEA5 FEA6 FEA7 FEA8 FEA9 FEA10 FEA11 FEA12 FEA13 FEA14 FEA15 FEA16 FEA17 FEA18 FEA19 FCE1Z FOEZ FPGMZ FDQ0 FDQ1 FDQ2 FDQ3 FDQ4 FDQ5 FDQ6 FDQ7 FDQ8 FDQ9 FDQ10 FDQ11 FDQ12 FDQ13 FDQ14 FDQ15 FEA0 FEA1 FEA2 FEA3 FEA4 FEA5 FEA6 FEA7 FEA8 FEA9 FEA10 FEA11 FEA12 FEA13 FEA14 FEA15 FEA16 FEA17 FEA18 FEA19 FCE1Z FOEZ FPGMZ SDA0 SDA1 SDA2 SDA3 SDA4 SDA5 SDA6 SDA7 SDA8 SDA9 SDA10 SDA11 SDA0 SDA1 SDA2 SDA3 SDA4 SDA5 SDA6 SDA7 SDA8 SDA9 SDA10 SDA11 SDBS0 SDBS1 XSDRAS XSDCAS XSDWE SDCKE SDCLK SDLDQM SDUDQM XSDCS SDDQ0 SDDQ1 SDDQ2 SDDQ3 SDDQ4 SDDQ5 SDDQ6 SDDQ7 SDDQ8 SDDQ9 SDDQ10 SDDQ11 SDDQ12 SDDQ13 SDDQ14 SDDQ15 SDBS0 SDBS1 XSDRAS XSDCAS XSDWE SDCKE SDCLK SDLDQM SDUDQM XSDCS SDDQ0 SDDQ1 SDDQ2 SDDQ3 SDDQ4 SDDQ5 SDDQ6 SDDQ7 SDDQ8 SDDQ9 SDDQ10 SDDQ11 SDDQ12 SDDQ13 SDDQ14 SDDQ15 VC H3 C4238 0.1u B B3 C3 FMPWN_OUT1 SP_SPFD SLEEP_SW LD_EN TEMP OSCEN WP1_OP WP2_OP WP3_OP SLEEP_SW LD_EN TEMP OSCEN WP1_OP WP2_OP WP3_OP H XSCK_IC_4201 TXD_TO_IC_4201 RXD_TO_IC_4201 XCS_IC_4201 TXD RXD LID_OPEN EJECT_DET PLG JTMS_J JTCK_J JTDI_J JTDO_J JNTRST_J JRTCK_J XSCK_IC_4201 TXD_TO_IC_4201 RXD_TO_IC_4201 XCS_IC_4201 TXD RXD LID_OPEN EJECT_DET PLG JTMS_J JTCK_J JTDI_J JTDO_J JNTRST_J JRTCK_J EQRF_S VC PH1 BH1 PI FE TE CE PH2 BH2 SWRF MPXOUT1 MPXOUT2 EQRF_S VC PH1 BH1 PI FE TE CE PH2 BH2 SWRF MPXOUT1 MPXOUT2 RFMCLK RFMCLK RECD1 AWBL DWBL LPP LPP2 RECD1 AWBL DWBL LPP LPP2 RFPDSH WFPDSH ROPCSH MSPDSH ATTPLS WLDON APCLOAD XRST_IC_4101 SCS SCLK SDAT RFPDSH WFPDSH ROPCSH MSPDSH ATTPLS WLDON APCLOAD XRST_IC_4101 SCS SCLK SDAT I J SV_FS4SV SLSTFD1 MNT5 SDA3 RXD_TO_IC_4201 PLG SDA6 SDA10 SDBS1 XSDCS XSDWE SDLDQM SDDQ7 XCS_IC_4201 VC-520 BOARD (9/20) DVD DSP, DVD DRIVE CONTROL XX MARK:NO MOUNT L WBVCTL L SV_NOISE F FFDR FRDR TFDR TRDR FMPWN_OUT0 FMPWN_OUT1 FEA0 VC B6 R4241 100k B7 FS4 SFDR PF6 PF5 PF1 PH5 PH2 PI6 PI4 SDA3 SDA6 SDA10 SDBA1 XSDCS XSDWE SDLDQM SDDQ7 SDDQ11 SDDQ4 SDDQ6 SDDQ14 XPDIAG ATDA2 INTRQ IORDY ATDD0 ATDD2 ATDD11 ATDD9 FEA16 FDQ15 ATDD7 FEA11 FEA9 FEA19 FDQ4 FDQ3 FDQ9 FEA17 FDQ8 FEA6 JTDO_J JTCK_J FEA6 R4260 XX XMUTE0 SCLK WLDON WP2_OP ATTPLS ROPCSH RFPDSH C4237 0.1u B K D4201 XX DWBL B8 E SDCKE C4240 0.01u B MNT2 R4223 1k B9 C4231 220p CH R4232 1200 JNTRST_J XX R4205 C4229 0.022u B C4227 0.1u B SDA9 SDBS0 SDDQ8 C4230 0.022u B C4219 10p C4228 0.022u JNTRST_J R4222 10k MPXOUT1 TEMP PH1 RECD1 SLSTFD2 TFDR C4226 0.1u B AWBL C4225 0.1u B R4221 10k ± 0.5% R4219 1k C4223 0.1u B GSHCK C4222 10p CH 22 R4225 1k R4215 R4214 3300 K PLLVCI DVSS1 VPD JTDO JTCK AA2 AB2 AB3 AB4 AB5 AB6 AB7 AB8 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AA22 Y22 W22 V22 U22 T22 R22 P22 N22 M22 L22 K22 J22 H22 G22 F22 E22 D22 C22 B22 B21 B20 B19 B18 B17 B16 B15 B14 B13 B12 B11 B10 SDDQ11 Y2 SDDQ4 W2 SDDQ6 V2 SDDQ14 U2 ATA_INTRQ T2 ATA_A2 R2 R4234 10k P2 ATA_IORDY N2 ATA_D0 M2 ATA_D2 L2 ATA_D11 K2 ATA_D9 J2 ATA_D7 H2 FEA16 G2 FDQ15 F2 FEA11 E2 FEA9 D2 FEA19 C2 FDQ4 B2 FDQ3 A2 FDQ9 A3 FEA17 A4 FDQ8 A5 FB4204 A6 JNTRST TFDR J SDA0 B4 SPVS PF7 SDA1 B5 PF3 RXD SDA5 J3 AVSS7 SDA4 A9 VDDE A8 BOTM1 PH7 DRV_SEL LID_OPEN XSCK_IC_4201 R4207 XX BH1 SDCK MNT7 MNT4 K3 VC VSS D FFDR L3 SDUDQM M3 VDDE BOOTSEL A7 VDDI IC4201 CXD5052GG-T6 DVD DSP, DVD DRIVE CONTROL TRDR C7 C9 AA3 AA4 AA5 AA6 AA7 AA8 AA9 AA10 AA11 AA12 AA13 AA14 AA15 AA16 AA17 AA18 AA19 AA20 AA21 Y21 W21 V21 U21 T21 R21 P21 N21 M21 L21 K21 J21 H21 G21 F21 E21 D21 C21 C20 C19 C18 C17 C16 C15 C14 C13 C12 C11 C10 DVDD1 SLSTRD2 Y3 ATDD3 FMPWN_OUT0 W3 ATDD12 VDDI SP_SPRD V3 ATDD14 OSCI PI U3 OSCO T3 VDDE XIOR R3 ATDA1 FE P3 VSS TE C6 DEW SKEW AVDD8 MPXO2 AVSS11 AVDD14 AVSS10 FB4205 WP1 PD2 WSP_SV VDDI APC_LOAD PB2 PB4 PB7 JTDI JRTCK TESTEN FDQ1 FEA1 FEA3 FDQ0 FEA18 FDQ13 FEA12 FDQ14 FEA15 ATDD4 ATDD15 ATDD10 ATDD13 ATDD1 DMACK DMARQ VDDI XCS0 SDDQ0 SDDQ1 ATDA0 PB5 SDA4 TXD PL1 PB1 I XCS1 VDDE PL2 R4202 XX SDCLK SDDQ13 PD1 WLDON XSDCAS VDDE VDDE PD3 C4209 0.1u B SDDQ5 ATP_WB SDUDQM SDDQ8 VSS WP2 SDDQ9 VDDE WSP_ROP SDDQ10 OSC_EN SDCKE WSP_RAP SDDQ3 SDBA0 DWBLI SDDQ2 VDDI WBLPFO SDDQ15 SDA9 SUBVSS2 WBLPFG XATA_DIOW SDA0 WBVCTL WBLPFN 10k SDA1 AVSS13 R4261 PI2 SDA5 WBLREF AWBLI C4204 0.01u FFDR WBLPFI WBVRT ATA_D6 TRDR WBDAO AVSS8 C4208 0.1u B AVDD10 PI7 TEMP R4201 1k PH1 MPXO1 FEA10 PH4 VDDI SVADRT2 FEA8 PF0 SVADRB2 SVNOISE FDQ5 AUX2 AUX1 FPGMZ PF4 PEAK1 FDQ10 SPDV PEAK2 AVDD7 FEA5 SKEWF SVADRB1 RCVRB FEA4 C4211 10u B AVSS2 SLSTR2 RCDAO L4202 10uH AVDD5 CE AVSS6 RCBIAS FEA2 VDDI AVSS5 SPRD AVSS1 1 C A1 AVDD6 SUBVSS1 3 2 M4 B1 C1 D1 E1 F1 SVADRT1 RECD1 33.8688MHz F C4202 0.1u B RCRFIN GSHCK C4210 10u B H RCVRT VDDE X4201 XATA_RESET AVSS3 SPCV MNT1 N4 TE SLSTF2 C4206 0.1u B FEA14 AVDD3 L1 XRST_IC_4101 P4 M1 WBVCTL OSCEN R4 N1 C4218 0.001u B T4 P1 C4216 0.1u B U4 R1 R4203 270k C4203 0.1u B V4 T1 C4215 0.1u B W4 U1 SWRF G RCVCTL V1 C4214 0.1u B PH2 Y4 W1 D Y5 Y1 CE VDDE G1 C4213 0.1u B Y6 FE H1 C4217 0.1u B C4250 0.47u R4259 1200 Y7 PI A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 B23 C23 D23 E23 F23 G23 H23 J23 K23 L23 M23 N23 P23 R23 T23 U23 V23 W23 Y23 AA23 AB23 AC23 AC22 AC21 AC20 AC19 AC18 AC17 AC16 AC15 AC14 AC13 AC12 AC11 AC10 AC9 AC8 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AB1 AA1 EQRF_S C4212 0.1u B Y8 RFMCLK J1 C4207 0.1u B C4201 0.1u B Y9 B C4236 0.1u B R4248 XX VSS K1 RFMCLK XSDRAS C SDDQ12 SDA8 SDA7 SDA2 SDA11 PI5 PH0 VDDI PF2 PH3 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 E20 F20 G20 H20 J20 K20 L20 M20 N20 P20 R20 T20 U20 V20 W20 Y20 Y19 Y18 Y17 Y16 Y15 Y14 Y13 Y12 Y11 Y10 PH6 D8 VDDI D7 FRDR VSS D6 SLDU VSS D5 SPCU VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS M12 L12 L13 M13 N13 N12 N11 M11 L11 K11 K12 K13 K14 L14 M14 N14 P14 P13 P12 P11 P10 N10 M10 L10 K10 R4247 68k C4233 XX AVDD12 10k C4232 0.1u B R4233 B E C4205 10p C4234 XX 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-14 VC-520 (9/20) 1 3 2 4 6 5 7 8 IC4303 W9864G6GH-7S-ER10 D_2.8V_S Note: IC4302 is not spplied, but this is included in VC-520 complete board. 64M SDRAM A SDDQ2 4 2.8 2.8 5 SDDQ1 6 C4302 0.1u B 2.8 7 SDDQ3 2.8 8 SDDQ4 C4303 0.1u B B 2.8 SDDQ5 SDDQ6 2.8 2.8 SDDQ7 2.8 0 SDLDQM XSDWE XSDCAS 2.8 2.8 2.8 XSDRAS 2.8 XSDCS SDBS0 2.8 2.8 SDBS1 SDA10 2.8 0 SDA0 C 0 SDA1 0 SDA2 SDA3 REG_GND C4304 0.1u B D_2.8V_S 0 2.8 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 2.8 DQ15 DQ0 VSSQ VDDQ DQ14 DQ1 DQ13 DQ2 VDDQ VSSQ DQ12 DQ3 DQ11 DQ4 VSSQ VDDQ DQ10 DQ5 DQ9 DQ6 VDDQ VSSQ DQ8 DQ7 VSS VDD NC LDQM UDQM WE CLK CAS CKE RAS NC CS A11 BS0 A9 BS1 A8 A10 A7 A0 A6 A1 A5 A2 A4 A3 VSS VDD 2.8 2.8 2.8 2.8 SDDQ15 SDDQ14 SDDQ13 REG_GND 2.8 2.8 2.8 2.8 2.8 SDDQ12 SDDQ11 FB4302 C4305 0.1u B C4310 1u B SDDQ10 SDDQ9 IC4302 39VF1601-70-4C-B3KE-GG013T 16M FLASH C4308 XX 2.8 SDDQ8 FEA15 FEA14 0 1.4 FEA13 SDUDQM FEA12 SDCLK FEA11 R0.5/P0.1 SDCKE 0 0 0 R0/P2.8 0 R0/P2.8 R0/P2.8 FEA10 FEA9 SDA11 FEA8 SDA9 FEA19 SDA8 SDA7 FPGMZ SDA6 SDA5 XIC_4201_RESET_A SDA4 REG_GND FEA17 FEA7 FEA6 D_2.8V_S FEA5 5 3 4 SDDQ2 7 SDDQ4 SDDQ5 SDDQ6 SDDQ7 E SDLDQM XSDWE XSDCAS XSDRAS XSDCS SDBS0 SDBS1 SDA10 SDA0 SDA1 SDA2 F SDA3 REG_GND 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 SDDQ3 8 6 SDDQ1 DQ0 Vccq DQ1 DQ2 Vssq DQ3 DQ4 Vccq DQ5 DQ6 Vssq DQ7 Vcc LDQM XWE XCAS XRAS XCS BS0 BS1 A10 A0 A1 A2 A3 Vcc FEA4 Vss DQ15 Vssq DQ14 DQ13 Vccq DQ12 DQ11 Vssq DQ10 DQ9 Vccq DQ8 Vss NC UDQM CLK CKE NC A11 A9 A8 A7 A6 A5 A4 Vss 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 SDDQ0 D 2 1 IC4301 XX Vcc D_2.8V D_2.8V FEA18 REG_GND A D_2.8V_S D1 C1 A1 B1 D2 C2 A2 B2 C3 A3 B3 C4 B4 A4 D3 D4 B5 A5 C5 D5 B6 A6 C6 D6 3 2.8 VSS VDD 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 SDDQ0 2.8 2 C4301 1u B 1 2.8 FEA3 SDDQ15 FEA2 FEA1 SDDQ14 SDDQ13 RB4301 10k 1 3 5 7 A15 A16 A14 BYTE# A13 VSS A12 DQ15/A-1 A11 DQ7 A10 DQ14 A9 DQ6 A8 DQ13 A19 NC DQ5 DQ12 WE# DQ4 RESET# VDD NC WP# RY/BY# DQ11 DQ3 DQ10 A18 DQ2 A17 DQ9 A7 DQ1 A6 DQ8 A5 DQ0 A4 OE# A3 VSS A2 CE# A1 A0 B E1 F1 H1 G1 E2 F2 H2 G2 E3 F3 H3 G3 G4 H4 F4 E4 G5 H5 F5 E5 G6 H6 F6 E6 FB4301 D_2.8V FEA16 FDQ15 FDQ7 FDQ14 FDQ6 FDQ13 FDQ5 C4311 0.1u B FDQ12 FDQ4 C FDQ11 FDQ3 FDQ10 FDQ2 FDQ9 FDQ1 FDQ8 FDQ0 FOEZ FCE1Z D FEA0 2 4 6 8 SDDQ12 SDDQ11 SDDQ10 SDDQ9 SDDQ8 E SDUDQM SDCLK SDCKE SDA11 VC-520 BOARD (10/20) SDA9 SDA8 SDRAM, FLASH SDA7 SDA6 XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE SDA5 SDA4 F REG_GND 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-15 VC-520 (10/20) • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 2 4 3 5 7 6 8 10 9 12 11 EQRF_S ADVC 1 A A VWDC3 C4138 39p CH VWDC2 VRDC 10k R4137 VWDC1 FPDO A_2.5V FVREF L4103 C4120 0.1u B 10uH A_2.5V C4113 4.7u B B 2 FL4101 XX 1 4 50 FPDO FPDIC_VC 49 FVREF FPDIC_GND 48 FPDIC_GND 47 FPDIC_GND 46 TLT+ 45 TLT+ 44 TLT- 43 TLT- 42 TRK+ 41 14 LDD_AVSS 13 VWDC3 TESTOUTP FL4103 XX LD_EN ENBL 12 2 1 TEMP 11 4 3 LDD_AVDD 10 1 3 B VC R4136 XX C4118 4.7u LDD_LVDD 6 OSCEN 5 DVSS 4 LDD_W1DIS 3 WP1_OP LDD_W2DIS 2 WP2_OP LDD_W3DIS 1 WP3_OP D IC4101 E CXA2725GA-T4 RF PROCESS B11 B12 C11 C12 D11 D12 CE BGIREF VTIREF BH2 PH2 CE 7 5 3 1 22k HAVC MPXOUT2 SWRF SWRF AWBL LPPC TESTOUTN AGC3C GND AGC2C TESTOUTP AGC1C ADVC VDD VC L2 M2 L3 M3 L4 M4 L5 M5 L6 M6 L7 M7 M8 L8 M9 L9 M10 L10 F11 G12 G11 H12 APCLOAD MPXOUT1 MPXOUT2 H11 H GND MPXOUT1 AWBL E B 0.001u C4129 B 0.1u C4130 0.1u B C4131 0.1u B C4132 M11 L11 F D_2.8V FB4103 D_2.5V D_2.8V FB4104 CL4111 D_2.5V C4126 XX C4111 4.7u B C4135 4.7u B CL4112 XRST_IC_4101 REG_GND CL4105 ATTPLS CL4108 G LPP2 LPP CL4109 WFPDSH XX RFPDSH WLDON CL4107 R4138 MSPDSH C4139 XX ROPCSH DVD MECHANISM DECK is replaced as block, so that there PRINIED WIRING BOARD and SCHEMATIC DIAGRAM are omitted. D 8 6 4 2 J12 G B TE C4134 0.1u B RB4101 AUX1 F OSCEN TE VCC E11 RFTC C PI FE E12 VCC RFDC B PI FE F12 NC GND NC ACHPF EQRF VWDC3 WAPCTC VWDC2 VRDC VRDCN VWDC1 FPDO RAPCTC VWDCN FVREF A DRV_A_3.9V FB4106 C4104 10u DVD MECHANISM DECK (DDX-C2000) (1/2) G C4117 4.7u A_2.8V C4137 XX FB4105 ADVC TEMP C4108 0.001u 7 C4136 10u C4107 0.001u LDD_LVDD C4141 0.1u VCC BH1 J11 LDD-W3SET GSW PH1 BH1 K12 VWDC1 DRFN PH1 K11 15 DRFP M12 L12 LDD-W1SET TESTOUTN HAVCC C WLDON VWDC2 B C4140 0.1u A12 AGCON VRDC 2 FL4104 XX 4 10u HAVC 16 8 A1 C4116 H A11 LPP2 G CL4141 17 9 B1 F CL4140 A10 LPP E CL4139 LDD-W2SET NC C1 CL4138 LDD_RSET NC APCLOAD D B10 DWBL 18 H C CL4137 A9 RECD1 19 H G B CL4136 20 G F A CL4135 B9 XRST 21 E A8 VCC 22 E C2 DRFN B8 DVCC D DRFP CL4134 A7 SCS 23 D HAVC B7 SCLK 24 C C A6 SDATA FB4102 C4102 1u B B B6 DGND GSW A5 GND SLEEP_SW 3 B5 MCLK 1 25 B A4 WFPDSH 26 B4 RFPDSH 27 RF- A3 MSPDSH 29 RF+ B3 ROPCSH PDIC_VCC 28 A2 ATTPLS 4 D2 2 30 A E1 31 PDIC_GAIN PDIC_VC B 0.1u FL4102 XX D1 C4119 SLEEP_SW F F GSW E2 32 DRFN FCS- F1 33 PDIC_GND C4109 0.1u B C4110 0.1u B DRFP F2 34 PDIC_GND TRK- FCS+ G1 FCS- C4112 4.7u B G2 35 B2 TRK+ H1 36 FCS- DRV_A_3.9V TLT- H2 FCS+ DRV_A_3.9V TLT+ J1 37 C4128 100p CH C4127 0.1u B J2 38 FCS+ BH2 L4102 10uH K1 39 TRK- B C4124 0.1u B PH2 K2 40 TRK- C4123 0.01u B CL4119 L1 TRK+ C4122 0.1u B RB4102 1M 8 7 6 5 4 3 2 1 C4114 10u B REG_GND FPDIC_OUT A E C4101 1u B 51 C4106 0.001u D 3 FB4101 FPDIC_VCC C4105 0.001u C REG_GND DRV_A_3.9V M1 CN4103 51P C4121 0.01u B DWBL RECD1 RFMCLK XRST_IC_4101 SCS SCLK SDAT VC-520 BOARD (11/20) H H RF PROCESS XX MARK:NO MOUNT 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-16 VC-520 (11/20) • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 1 2 4 3 5 7 6 8 10 9 12 11 A A DRV_SEL FCS+ FGINI FCSFB4401 D_2.8V TRK+ D_2.8V TRK- B B DRV_SEL TLT+ TLTEJECT_DRV REG_GND C4404 10u B Q4402 UNR32A300LS0 LED DRIVE REG_GND D4402 XX 0 4 ACCS_LED 5 3 2 1 1.7 FMPWN_OUT1 CN4402 TLIM CLK ST1OP FGSEL VM2 BRMOD EJO SPDIR PGND3 PGNDSP EJIN FMPWN_OUT0 TRDR LID_OPEN TFDR EJECT_DET RB4402 XX 1 3 5 7 2 4 6 8 ACCS_LED 2 ACCS_VCC 3 EJECT_DRV 4 REG_GND(D_MT_GND) 5 XEJECT_SW 6 LID_OPEN 7 REG_GND 8 EJECT_DET C FRDR FP-569 FLEXIBLE FFDR Page 4-29 of Level 2 D SLED4 SLED3 SLED2 SLED1 C4410 10u A1 B1 C3 C2 D2 C1 D3 D1 E2 E3 E1 E4 F1 F2 G1 G2 E XEJECT_SW 8P 1 ST2IM ST2IP ST1IM PGNDSP COM H1 H2 F3 G3 G4 H3 F4 H4 G5 F5 H5 E5 H6 G6 H7 G7 NC PGND1 TLOP TLOM NC VM1 PGND1 VM1 TROP TROM FCOM VM2 L4402 4.7uH C4411 0.022u R4406 68k C4405 XX PGND2 ST1OM VM3 2.8 ST2OP IDLE ST1IP Q4401 UNR31A3G0LS0 SWITCH ST2OM MUTE W 0 SP_SPRD GND SPRNF2 2.8 LIMSET SPRNF1 BRMOD PGND2 IC4401 R2A30212LG-W00B : Non MEGA model BD6310AGU-E2 : MEGA model DVD MECHA DRIVE VCC SPGND XMUTE1 SV_FS4SV SPDRV V XMUTE0 XMUTE0 FCIP VSP 12k FCIM REF SPRNF1 R4405 TRIP TEST VSP C4403 10u 7 5 3 1 TRIM NC U D 7 5 3 1 PGND1 FG REG_GND RB4401 100k 8 6 4 2 8 6 4 2 NC R4413 180 D_2.8V TLIP NC SP_SPFD B2 A2 B3 A3 D4 A4 C4 B4 A5 C5 A6 B5 B6 C6 A7 A8 C4402 0.047u B RB4403 10k FCOP C MDID B7 B8 C7 C8 D5 D8 D6 D7 E8 E6 F8 E7 F7 F6 G8 H8 E EJECT_DRV PLG CN4401 L4403 DRV_MT_4.3V 1uH DRV_MT_4.3V C4406 22u 10V TA 1 REG_GND SLED1 2 SLED1 SLED2 3 SLED2 SLED3 4 SLED3 SLED4 5 SLED4 W 6 W V 7 REG_GND L4404 DRV_MT_5.0V C4408 10u B DRV_MT_5.0V 1uH COM F SLSTRD2 U SLSTFD2 V SLSTRD1 W 10P REG_GND V U 8 U COM 9 COM REG_GND 10 REG_GND F SLSTFD1 R4409 1 R4410 1 R4411 1 DVD MECHANISM DECK (DDX-C2000) (2/2) MEGA model DVD MECHANISM DECK is replaced as block, so that there PRINIED WIRING BOARD and SCHEMATIC DIAGRAM are omitted. G G Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E VC-520 BOARD (12/20) H DVD MECHA DRIVE H XX MARK:NO MOUNT NO MARK:REC/PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-17 VC-520 (12/20) 1 2 3 5 4 6 9 8 7 10 11 12 14 13 15 16 A A CL2405 CL2404 R2405 XX B C2409 B XBB_RST XX D_2.8V D_2.8V C2423 XX DR_VINCK C2427 B 2.2u R2439 XX REG_GND D_2.8V A_2.8V A_2.8V D_1.2V D_1.2V C2429 B 2.2u C FB2401 D_1.2V TSTOUT22 GRSLPILOT ALYDT2_TSTO2 HMYO5 ALYDT0_TSTO0 TSTOUT21 ALYDT4_TSTO4 HMYO6 ALYDT1_TSTO1 TSTOUT20 ALYDT3_TSTO3 HMYO7 IC2401 ALYDT5_TSTO5 TSTOUT19 R8A01015ABGTLV D/A CONVERTER ALYDT7_TSTO7 AVSS_r2 LNDAPBREXT IOVDD5 AVDD5 IOVSS5 LNDAPBDT ALYDT6_TSTO6 AVSS5 ALCDT1_TSTO9 LNDAPRDT ALCDT3_TSTO11 AVDD4 ALCDT0_TSTO8 LNDAPBCBU ALCDT2_TSTO10 AVSS4 ALCDT4_TSTO12 ALCDT7_TSTO15 LNDAPRCBU ALCDT5_TSTO13 LNDAPRREXT LNDAYDT ALCDT6_TSTO14 LNDAYREXT IOVDD6 LNDAYCBU ALFLDO_TSTO16 DVDD7 AVSS3 ALVDO_TSTO17 AVDD3 DVSS7 AVDD2 EVDARDT ALCKO13 AVSS9 IOVSS6 EVDAGDT ALHDO_TSTO18 AVDD11 SICKSEL PLLALVSS EVDABDT PLLALVDD AVSS2 EVDACBU ALCK13 AVVSS_l1 AVDD10 ANATEST EVDAREXT AVDD8 PNDAREXT ACCVO PNDACBU AVSS6 AVSS1 AGCVO PNDABDT CLPVO AVDD1 AVDD9 PNDAGDT AA1 reserve ALADCVRBB Digital PANEL PNDARDT CL2409 CL2408 CL2407 0.001u R2407 3900 ± 5% 180 ± 5% RB2401 XX A_2.8V LNDAPBDT B R2408 IC_2401_C/PB_OUT R2421 DPNDE DPNHD XX IC_2401_Y_OUT R2423 C2415 XX 1 4 2 A_2.8V 0.1u 5 6 G 3 Q2401 XX LNDAYDT R2411 R2412 C2417 180 ± 5% 3900 ± 5% A_2.8V 0.1u H R2417 12k C2419 0.1u ± 0.5% RB2402 XX PNDABDT C2414 0.001u 270 R2418 ± 0.5% 270 R2419 ± 0.5% PANEL_B A_2.8V R2427 XX R2428 XX R2429 XX PNDAGDT B PANEL_G PNDARDT 270 R2420 8 2 C2420 XX I PANEL_R ± 0.5% AVVSS_l2 DPNVD DVSS2 DVDD2 DPNCKO DPNB1 B1 A1 D1 E4 E1 F4 D2 C2 F1 G4 E2 D4 G1 H4 F2 E5 G2 J4 H1 F5 H2 G5 J1 K4 J2 H5 K1 J5 K2 L4 L1 K5 L5 L2 M4 M1 M5 M2 N5 N1 N4 N2 P5 P1 R5 P2 P4 R1 T5 R2 W2 T1 R4 T2 AA3 U1 T4 U2 U4 V1 V2 W1 Y2 Y1 CL2406 C2411 1 DPNB2 DPIOVSS2 DPNB4 DPIOVDD2 DPNB5 DPNB0 DPNB6 DPNB7 DPNG3 DPNG2 DPNB3 DPNG0 DPNG4 DPIOVSS1 DPNG5 DPNG1 DPNG6 DPIOVDD1 DPNR2 DPNR0 DPNG7 DPNR1 DPNR5 DPNR7 DPNR6 DPNR3 PNVD DVDD1 DPNR4 PNHD DVSS1 EVFVD EVFHD SO IOVDD1 ALADCVRTB F 2 4 6 8 HMYO4 GRSLDT3 1 3 5 7 HMYO3 TSTOUT23 TSTEN 2 4 6 8 TSTOUT24 GRSLDT1 1 3 5 7 HMYO2 TSTCKEN A_2.8V GRFSDT3 E D_2.8V IOVDD2 D D_1.2V HMYO1 GRSLDT2 AA2 AA1 AA4 V5 AA5 V6 Y4 Y3 AA6 V7 Y5 V4 AA7 V8 Y6 U5 Y7 V9 AA8 U6 Y8 U7 AA9 V10 Y9 U8 AA10 U9 Y10 V11AA11 U10 U11 Y11 V12AA12 U12 Y12 U13AA13 V13 Y13 U14AA14 U15 Y14 V14AA15 U16 Y15 Y19AA16 V15 Y16 W21AA17 V16 Y17 V17AA18 Y18AA19 Y20AA20 HMCBO6 HMCBO2 GRFSPILOT ALADCVR1 I IOVSS2 DVDD9 XCS B HMYO0 HDMI IOVSS1 0.001u GRFSDT0 XSCK C2402 HMCRO0 GRSLDT0 SEL18 G HMCRO7 GRFSDT2 SI B RETSTEN AVSS_r1 C2401 0.001u HMCRO6 VIN2 ALADYVRTI DR_GSPILOT F VIN0 ALADYVRBI DR_GSDATA3 HMCBO4 DVSS5 AVDD6 DR_GSDATA1 HMCRO5 GRFSDT1 ALADYVINP DR_GHDATA3 DVDD3 ALADYVINN DR_GSDATA2 HMCRO4 VIN5 ALADYVRTB DR_GHPILOT DVSS3 VIN3 AVSS7 DR_GHDATA0 HMCRO3 PLLHMVSS ALADYVR1 DR_GSDATA0 HMCRO2 VIN1 ALADCVINP DR_GHDATA2 PLLHMVDD ALADYVRBB DR_VDATA2 HMCRO1 AVDD7 DR_VDATA0 HMCBO5 VIN4 AVSS8 DR_GHDATA1 AA21 reserve IOVSS3 IOVDD3 HMCBO1 HMCBO3 HMCBO0 HMVD HMHD DVSS4 DVDD4 HMFLD TSTIN0 TSTIN3 HMPXCKO TSTIN2 TSTIN1 HMMCKO DVDD8 TSTIN6 TSTIN5 TSTIN4 TSTIN7 TSTIN9 TSTIN8 IOVSS4 IOVDD4 TSTIN10 TSTIN13 TSTIN11 TSTIN14 TSTIN12 TSTIN15 DVDD6 TSTIN16 TSTIN17 XRST TSTIN18 SDSET DVSS6 TSTIN19 TSTIMD0 TSTIMD1 TSTIMD2 TSTIMD3 TSTIMD4 TSTCKIN5 TSTCKIN4 SCKO TSTOMD0 TSTCKIN3 TSTCKIN2 VINCK SCK54 DVDD5 TSTOMD1 TSTOMD2 TSTOMD3 TSTCKIN1 MVO TSTOMD4 TSTOMD5 VIN7 DR_VDATA5 A21 reserve A1 reserve DR_VDATA3 HMCBO7 VIN6 ALADCVINN DR_VDATA1 A2 B2 A3 B4 A4 D5 B5 D6 A5 C1 B6 D7 A6 B3 B7 E6 A7 D8 B8 E7 A8 E8 B9 D9 A9 E9 B10 E10 A10 D10 B11 E11 E12 A11 D11 B12 E13 A12 E14 B13 D12 A13 E15 B14 E16 A14 D13 B15 E17 B16 D14 A15 D18 B17 D15 A16 B19 B18 D16 A17 D17 A18 A21 A20 DR_VDATA6 H A_2.8V B21 B20 C21 D20 D21 E18 E20 F18 E21 A19 F20 G18 F21 C20 G20 F17 G21 H18 H20 G17 H21 H17 J20 J18 J21 J17 K20 K17 K21 K18 L20 L17 M17 L21 L18 M20 N17 M21 P17 N20 M18 N21 R17 P20 T17 P21 N18 R20 U17 T20 P18 R21 V18 U20 R18 T21 W20 V20 T18 U21 U18 V21 AA21 Y21 DR_VDATA4 E R2440 XX A_2.8V D_1.2V C2410 XX DR_VDATA7 D C2428 B 2.2u D_1.2V R2402 XX D_1.2V A_2.8V C2404 0.001u B D_2.8V A_2.8V C2425 XX C D_2.8V C2424 XX D_2.8V 7 3 6 4 5 Q2402 XX J J C2407 0.001u B C2408 0.001u B D_1.2V A_2.8V D_2.8V K BB_SO K XBB_SCK XCS_IC_2401 BB_SI VC-520 BOARD (13/20) PANEL_HD D/A CONVERTER PANEL_VD XX MARK:NO MOUNT L L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-18 VC-520 (13/20) 1 2 4 3 5 7 6 8 10 9 11 12 A A C2902 0.047u B B B INT_MIC_R D_2.8V REG_GND INT_MIC_L C2901 0.047u B C2903 0.001u B C2912 XX 7 5 3 1 C2905 0.001u B 8 6 4 2 2200 RB2902 C2917 XX C2915 0.1u B 7 5 3 1 RB2901 10k 8 6 4 2 C XCS_IC_2801/IC_2901 C2926 0.1u B 2.6 2.8 0.2 1.4 0.3 2.4 1.4 1.4 1.4 1.4 BB_SO 2.8 RB2903 100k 1 2 4 3 6 5 7 8 C C2927 0.1u B C2918 XX R2905 XX XBB_SCK C2933 0.022u B 4.8 Q2901 MCH3211-TL-E 3.6V REG MT_5.0V 3.6 R2904 47k C2932 0.1u B 1 2 3 4 5 6 7 8 9 C2924 0.1u B SP+ CLOCK ZAP 1.4 D R0.7/P0 ADA_SOA0 R0.7/P0 ADA_SIA0 0 C2921 1u 0 C2919 0.01u IC_2401_Y_OUT IC_2401_C/PB_OUT 2.8 L2903 10uH B A_2.8V 0 2.8 C2916 4.7u B C2920 0.1u B E 10 11 12 REG_GND C2923 4.7u SP- F DATA CS OFFSET AGC_TC VCCDRIVE R1.4/P0 R2903 4700 MICVCC VCCSP 4.1 AU_4.6V INT_MIC_L COUT C2904 1u E INT_MIC_R VCC BEEP_IN 13 14 15 16 17 18 19 20 21 22 23 24 C2909 0.047u B VREFSP 1.4 VOUT R2902 4700 CIN YOUT R2901 22k 3.6 SP_AGC ADA_LRCK 1.4 0 1.8 SYS_SOUND V_GND 0 1.8 YIN LINE_IO_R 10u C2907 4.7u B GND VSS 0 SDIN IC2901 NN12922A-BB VIDEO OUT, AUDIO I/O GND 0 AUDIO_R_I/O VCC LINE_IO_L C2922 8 7 5 6 3 4 2 1 RB2904 100 C- 0 AUDIO_L_I/O C_GND 2.8 0 B SDOUT C+ 4.7u WCLK VREF VDD C2929 OFFSET 0 1.4 2.8 1.4 OFFSET B MCLK SPOUT_- 0.1u OFFSET SPGND C2910 C2928 4.7u B 1.4 1.9 D 0.1u B R1.4/P0 L2904 10uH ADA_FCK BCLK SPOUT_+ C2930 AU_2.8V ADA_BCK VCCH OFFSET_SP 4.6 48 47 46 45 44 43 42 41 40 39 38 37 C2906 4.7u B 1.9 L2905 10uH EXT_MIC_R AU_4.6V VDD EXT_MIC_L 36 35 34 33 32 31 30 29 28 27 26 25 L2902 A_2.8V C2911 10u B C_TO_PB VIDEO_OUT S_Y_OUT F V_TO_PR Y_TO_Y 10uH G G VC-520 BOARD (14/20) :DVD110E/DVD610/DVD610E VIDEO OUT, AUDIO I/O H H XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-19 VC-520 (14/20) Ver. 1.1 2008.01 1 2 4 3 5 6 8 7 9 11 10 12 A A AU_4.6V B AU_4.6V XBB_SCK L2802 10uH C2823 4.7u B BB_SO XCS_IC_2801/IC_2901 XSYS_RST C2832 XX C2831 XX C2844 XX C2838 XX R2809 XX 2 4 6 8 C2828 XX XSYS_RST R2808 XX R2807 XX C 1 3 5 7 RB2804 47k AUDIO_L_I/O 1 3 5 7 2 4 6 8 ADA_BCK C2814 1u 4.1 0.1u 0.1u 0.1u 0.1u C2833 C2836 C2839 0.1u C2830 C2834 V_IN MICVCC_R V_GND VCC_L Y_IN MONI_L2 LOOP_IN SPAGC_TC Y_IN_1 SPAGC_OUT Y_IN_2 SPAMP_OUT VCC_V SP_IN C_IN_1 VCC_SP C_IN_2 VREF_SP V_GND MONI_RECPB_R2 C2850 XX D IC_2401_Y_OUT IC_2401_C/PB_OUT E C2847 1u A_2.8V C2848 L2805 10uH A_2.8V 0.01u C2851 4.7u N.C DRIVE_COUT VCC_DRIVE DRIVE_VOUT DRIVE_GND SDC_OUT N1 N2 P2 N3 P3 P4 N4 N5 P5 P6 N6 N7 N8 P7 P8 N9 P9 N10P10 N11P11 P12 P13 P14 WCLK DATAOUT_Front BCLK MCLK ZAP_GND XRST INT_EXT_OUT MIC_MONO_OUT SI SCK A_GND OFFSET_RR VCC_H MONI_L1 OFFSET_RL OFFSET_FL OFFSET_FR AGC_TC_Rear MICVCC_F XCS CLAMP_TC Rear_SHOE_R VSS_IN 4.8 F AGC_TC_Front Rear_SHOE_L SP+ MT_5.0V SDC_IN NN12923B-BB VIDEO, AUDIO I/O C2825 0.01u 3.6 LINE_IN_L A_GND VSS_OUT C2824 4.7u C_IN IC2801 DRIVE_YOUT C2815 0.0047u R2819 68k Y_GCA Rear_INT_R P_C2 Q2801 MCH3211-TL-E 3.6V REG SYS_SOUND R2804 XX VREF_L P_GND SYS_SOUND Y_IN_OUT P_C1 AU_2.8V SYS_SOUND C_GCA Rear_INT_L VDD_P 0.1u D_GND Front_SHOE_R LINEOUT_R C2820 C_IN_OUT A_GND R2818 6800 AU_2.8V EXT_R Front_SHOE_L OFFSET_PBR L2801 10uH SDC_J LINEOUT_L C2822 XX R2805 XX VCC_D OFFSET_PBL R2806 XX C2819 XX DATA_IN MONO_DET_IN HPOUT_R E D_2.8V EXT_L A_GND C2821 4.7u D_2.8V ZAP MICDET2 MUTE_OUT C2806 0.001u C2812 0.001u SHOE_MIC_FR ADA_SIA0 DATAOUT_Rear HPOUT_L C2801 0.1u SHOE_MIC_FL MONITOR_R1 SP- MEGA model LINE_IN_R Front_INT_L 1 3 5 7 D Front_INT_R SP_GND 0.047 C2805 4.7u ADA_SOA0 ADA_SOA1 RB2801 2.2k C2802 0.1u ADA_LRCK B14 C13 C14 D13 D14 E14 F14 E13 F13 G14 H14 G13 H13 J13 K13 J14 K14 L14 L13 N12 M14N14 M13N13 A1 A2 A3 A4 B4 A5 B5 A6 A7 B6 B7 A8 B8 A9 B9 A10 B10 A11 B11 A12 B12 A13 A14 B13 0.047 C2818 0.001u 0.047 C2817 0.001u C2811 C2808 C2809 2 4 6 8 INT_MIC_F C2816 0.001u INT_MIC_L C2829 0.1u 22k RB2803 INT_MIC_R C ADA_FCK AUDIO_R_I/O F B1 B2 C2 D2 B3 C1 D1 E2 E1 F2 F1 G1 G2 H2 H1 J2 J1 K2 K1 L2 L1 M1 M2 P1 R2803 C2845 0.01u 47k C2842 4.7u SP+ SP- C2843 10u R2802 4700 SP+ AU_4.6V A_2.8V L2803 10uH REG_GND C2835 C2837 0.1u 0.1u C2840 C2841 10u 0.1u C_TO_PB G 1 3 5 7 AUDIO_L_I/O AUDIO_R_I/O 2 4 6 8 G V_TO_PR Y_TO_Y RB2805 100 VC-520 BOARD (15/20) H :DVD115E/DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E VIDEO, AUDIO I/O MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E H XX MARK:NO MOUNT NO MARK:REC/PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-20 VC-520 (15/20) 1 2 4 3 5 7 6 8 10 9 12 11 Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E L3103 EP_8.5V 10uH A L3102 EVF_COM_CN 10uH C3112 2.2u B L3101 A_2.8V R3101 XX 10uH A_2.8V EVF_VR C3102 PANEL_R C3103 10u B 0.01u COMDA_PANEL 2.8 PANEL_HD 2.6 L2.1/E1.8 COMDA_EVF COM_EVF SI VST VDD VDD SCAN VCK XHD VSS 2.8 XVD POFF XCLR VSS RGT HCK1 HCK2 HST PCG 1 2 3 4 5 6 7 8 9 2.8 PANEL_VD XBB_RST COMREF WIDE D R3104 XX XSTBY_P XSCK 13 14 15 16 17 18 19 20 21 22 23 24 0.3 PANEL_NOR/REV GND2 IC3101 CXM3018R-T4 LCD/EVF DRIVE XCS EVF_VP 2.5 POFF EVF_VB 4.5 EVF_REF 5 EVF_GND 4 EVF_HCK1 3 EVF_HCK2 2 EVF_HST 4 2.8 3 8.5 8 6 4 2 2.5 2.5 L2.8 /E0 0 7 5 3 1 EVF_VR Page 4-26 of Level 2 D3101 XX C MEGA model BL-022 0 CN5701 Through the Flexible Flat Cable (FFC-140) Q3106 UNR32A3G0LS0 Page 4-26 of Level 2 CL3104 CN3102 EVF_VST 0 EVF_VCK PANEL_VR 2 PANEL_VG 3 PANEL_VB 4 REG_GND 5 REG_GND 6 VDD_P 7 EP_2.8V 8 D_2.8V 9 BL_H3 EVF_EN 10 BL_H2 EVF_STBY 11 BL_H1 12 REG_GND 13 KEY_AD0 14 TP_X 15 TP_SEL1 16 TP_Y 17 REF 18 PANEL_NOR/REV 19 HCK1 20 HCK2 21 HST 22 PCG 23 EN 24 PSIG 25 XSTBY 26 DWN 27 RGT 28 VST 29 VCK 30 COM EVF_PCG D KEY_AD0 TP_X EVF_HCK2 TP_SEL1 EVF_HCK1 C3109 XX 30P 1 2.8 1.4 EVF_HST TP_Y COM_P XSTBY_P PANEL_NOR/REV DWN_P 18P CN5701 Through the Flexible Flat Cable (FFC-140) 10 11 12 E EVF_VDD C3120 0.01u B 0 B Non MEGA model BL-021 EVF_VG 2.5 XBB_RST RGT_P EVF_STB 6 CN3101 EN BB_SO KEY_AD0 KEY_AD0 PANEL_NOR/REV SO 6 5 2 1 R3121 100k Q3106, Q3107 B+ SWITCH RB3101 XX 2.5 2.6 VR TEST DWN TP_Y XX R3103 XBB_SCK XBB_SCK VG OPIN L2.8/E0 TP_Y 2.5 VB XSTBY_E TP_X TP_X XCS_LCD C3116 0.1u B VCC2 0.2 TP_SEL1 0.7 EVF_VST 7 1 Q3107 MCH6305-TL-E-S 8.5 OPOUT L0/E2.8 BB_SI EVF_VCK 8 EVF_HST B C3115 VP GND1 0 1.4 1.4 1.2 CH R3102 68k XBB_RST TP_SEL1 EVF_EN 9 EVF_HCK2 10u TRST 1.4 BB_SI BB_SI C3106 560p L2.8/E0 C3105 0.1u B BB_SO 2.8 XBB_SCK COM_PANEL COMDA_PANEL REF BIN EXTDA GIN RIN XCS_LCD XBB_RST EVF_PCG 10 EVF_HCK1 L2.5/ E2.3 L4.1/E3.7 L2.1/E2.3 L0.6/E1.8 L2.3/E2.5 1.4 1.7 1.7 1.7 2.8 1.2 Filter VCC1 PANEL_HD 48 47 46 45 44 43 42 41 40 39 38 37 C EVF_VB 11 EVF_REF EXTDA PANEL_VD BB_SO EVF_VR 12 EVF_STBY 36 35 34 33 32 31 30 29 28 27 26 25 XBB_SCK EVF_VG 13 EVF_VST COM_PANEL 0.01u REG_GND XCS_LCD EVF_PSIG 14 EVF_VCK C3118 RB3104 10k 8 7 5 6 3 4 2 1 0.01u EVF_EN EVF_REF C3113 4.7u PANEL_VD 15 EVF_PCG R3105 100k ± 0.5% PANEL_HD EVF_COM EVF_VB R3122 XX B C3101 PANEL_G EP_4.6V 16 EVF_VP C3104 1u B PANEL_B LED_K 17 EVF_VG C3108 C3110 4.7u 10u B B C3107 XX A 18 EP_4.6V A_4.6V D_2.8V E XSTBY_P DWN_P R3111 XX RGT_P 2 3 EVF_BL_ON COM_P 1 6 L0/ E0.6 4 F L2.3/E1.5 R3119 2200 PANEL_BL_ON L0/E1.2 L3.8/ E0 L3.3/ L3.2/ E4.6 E0 L3.3/ E0 RB3103 8 7 5 6 3 4 2 1 8 A_IN+ B_IN- GND B_IN+ 6 L3.2/ E4.6 Vcc B_OUT A_IN- L3.9/E4.1 Q3101 L3.2/ UP04501G08S0 E4.6 4.5 L3.3/ E0 Q3101-Q3104 LCD BACKLIGHT DRIVE A_OUT 7 8.5 L3.8/E0 L3.9/E4.6 5 L3.9/ E4.6 Q3104 2SA1832-YGR-TE85L 1 L3.9/ E4.6 Page 4-29 of Level 2 LCD/EVF BACKLIGHT CONTROL IC3102 NJM12904V(TE2) 2 3 Q3103 2SA1832-YGR-TE85L L3.9/ E4.6 LND031-LND060 L7.3/ E0.7 R3114 18 ±0.5% 3 2 6 1 4 5 L3.2/ E4.6 L0.1/ E4.6 R3109 2200 R3113 18 ± 0.5% 4 RB3102 47k 2 4 6 8 C3121 4.7u B G Q3102 2SA1832-YGR-TE85L L0.6/ E0 1 3 5 7 A_4.6V R3107 30k : Non MEGA model 39k : MEGA model ± 0.5% R3110 18 ± 0.5% R3108 4700 F FP-573 FLEXIBLE 5 L0/ E1.2 Q3105 UP04601G08S0 EVF BAKLIGHT DRIVE L7.3/ E0.7 L0/ E0.6 L0.2/ E0.6 100k C3119 XX R3112 1k G R3120 150 : Non MEGA model 82 : MEGA model ± 0.5% R3115 220k REG_GND ± 0.5% VC-520 BOARD (16/20) LCD/EVF DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE L:LCD MODE E:EVF MODE H H 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-21 VC-520 (16/20) 2 4 3 5 7 6 8 10 9 D_2.8V D_1.2V D_1.2V D_1.2V EVER_3.0V EVER_3.0V R4901 XX EVER_3.0V VOUT VTR_UNREG VOUT VOUT 2 4 6 8 VOUT 12 11 D2.8V D_2.8V A RB4905 47k VTR_UNREG BATT_UNREG BATT_UNREG A 1 3 5 7 1 XCAM_LED XPOWER_SW BATT_IN FR_XRESET GND XCAM_LED RB4904 1k 1 2 4 3 6 5 7 8 XPOWER_SW XMS_IN TA REG_GND BATT/XEXT C4901 22u XCHARGE_LED XCHARGE_LED C4912 XX XBATT_VIEW XBATT_VIEW C4914 0.01u B XIC_4201_RESET XEJECT_SW E2 F1 F2 L7 2 4 6 8 LANC_IN LANC_OUT 1.8/3VCTRL WD_DIS C STABLE_RUN XHOT_STBY FAST_CHARGE INIT_CHARGE_ON XCAM_LED XCHARGE_LED BOOT_MODE_PORT0 D GENERAL_AD SYSTEM_AD K7 L8 K8 K11 K9 J10 J11 H9 H10 H11 G10G11F11 F10 E11 E10 E9 D11D10 D9 C11 C10 B10 B8 1 3 5 7 K6 J7 R4932 100k EVER_3.0V R4935 1k XX XX E R4931 XX XX 10k R4936 CL4911 D_1.2V C4915 0.1u B CL4912 R4929 470k VCC XFR_SCK FR_SO FR_SI XCS_EX XLANC_ON CLAMP_ON C4913 0.01u B XCS_DD XX VTR_DD_ON 1.8/3VCTRL R4941 1.8/3VCTRL 10k F R4942 ±0.5% XX IC4905 XUNREG_RESET C4905 XX L6 XFLASH_RST 2 4 INA 5 FR_EVER_SCK K5 J5 1 INB OUTY GND XFLASH_RST 3 R4909 XX R4937 D_1.8V FR_EVER_SO RB4903 10k 3 CL4910 FR_EVER_SCK L5 CL4909 GENERAL_AD FR_EVER_SO G1 G2 H2 H3 J4 R4926 GENERAL_AD E1 FR_EVER_SCK SYSTEM_AD B1 C2 C1 C3 D2 D1 D3 E3 XSYS_RST VCC IC4904 XX C4904 XX P65 P35_AN05 FR_EVER_SO SYSTEM_AD P66 P04_INT08 R4928 5 INA 2 4 BATT_IN BATT_IN P67 P36_AN06 1 INB OUTY GND P70_INT00 P03_INT07 P34_AN04 XBATT_VIEW XX P71_INT01 P37_AN07 P33_AN03 XMODE_SW P72_INT02 P40_AN08 P02_INT06 P50 P32_AN02 VTR_DD_ON 7 5 3 1 P74 P41_AN09 P01_INT05 BEXCK P31_AN01 8 6 4 2 P73_INT03 P76_SO2 P75_SCK2 VCC1 P77_SI2 VSS2 VCC2 VSS3 VSS1 VSS6 VSS4 VSS7 VSS5 VSS8 NC P00_INT04 P51 P30_AN00 3 RB4902 1k P52 BSOUT2 XX INB 2 4 C4903 XX XEJECT_SW R4908 XX XCS_DD P42_AN10 BSOUT1 R4918 XX INA XPOWER_SW 1 INB OUTY 5 2 3 INA XSYS_RST XCS_DD AVR P53 P27_SCK0 IC4903 1 4 5 C4902 XX OUTY BATT_SIG VTR_DD_ON P43_AN11 BSIN P26_SO0 XX BATT_SIG VTR_DD_ON P44_AN12 AVSS P54 HI CONTROL P25_SI0 XIC_4201_RESET P55 MB95005BGL-G-110-ERE1 P24_CS0X XX IC4902 E P45_AN13 AVCC IC4901 P23 0.1u R4907 XSYS_RST BATT/XEXT P46_AN14 SUBCK2 P56 BRSTX P22 C4910 XIC_4201_RESET BATT/XEXT P47_AN15 SUBCK1 P57 P05_INT09 R4903 XSYS_RST SIO2 1 3 5 7 RB4901 10k XDR_RESET 2 4 6 8 XUNREG_RESET BDBMX P60_PPG10 CPO P21_PPG01 CL4908 CLAMP_ON VCI P61_PPG11 P20_PPG00 CL4905 BOOT_MODE_PORT0 X1A P17 ± 0.5% BATT_SIG XUNREG_RESET NC R4917 1k ± 0.5% 1800 X0A P16 CL4902 C4909 0.1u B P62_LSO P15 CL4901 R4913 TMD P14 FR_SO XFR_SCK R4915 6800 C4908 B 0.01u XX P63_LSI P13_ADTG R4910 P64 MOD P12_SCK1 1 C4907 CH 12p RSTX P11_SO1 3 CL4906 D C6 A10 J2 B11 C4 A5 B5 C5 A6 B6 C7 A7 B7 C8 A8 P10_SI1 FR_SI R4914 XX 2 CL4904 CLAMP_ON F3 P07_INT11 XCS_EX K3 K1 K2 C4906 CH 10p WD_DIS CL4903 BOOT_MODE_PORT0 G9 G3 F9 P06_INT10 FR_SO XFR_SCK J6 XLANC_PWR_ON FR_SI J8 L2 XCS_EX J9 H1 L3 C L11 J3 STABLE_RUN R4911 10M 1608 WD_DIS XHOT_STBY X4901 32.768kHz STABLE_RUN C4911 B 0.1u VSS9 XSYS_RST XMS_IN XHOT_STBY B C4916 0.1u B A1 J1 XEJECT_SW XMODE_SW K4 A4 A9 C9 B9 A11 L1 XMODE_SW B2 A2 B3 A3 B4 K10 L9 L10 L4 B R4933 47k ± 0.5% C4917 0.01u B R4930 1M ± 0.5% R4934 100k ± 0.5% F VTR_UNREG BATT_UNREG FAST_CHARGE FAST_CHARGE INIT_CHARGE_ON INIT_CHARGE_ON XIC_4201_RESET XSYS_RST FR_XRESET XFLASH_RST FR_XRESET G LANC_IN G LANC_IN LANC_OUT Note: IC4901 is not supplied, but this included in VC-520 complete board. LANC_OUT XLANC_PWR_ON XLANC_PWR_ON XLANC_ON XLANC_ON VC-520 BOARD (17/20) H HI CONTROL H XX MARK:NO MOUNT 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-22 VC-520 (17/20) • Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. 1 2 4 3 5 7 6 8 10 9 12 11 GSHCK A A AO 1.3 VCC R4501 100k INIT_CHARGE_ON FAST_CHARGE A_2.8V 6 5 2.8 GND MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E C4505 0.0022u B C4506 4.7u B B REG_GND (1.4A/32V) F002 (1.4A/32V) F003 (1.4A/32V) F004 (1.4A/32V) DRV_UNREG MT_BL_UNREG VTR2_UNREG 4 R4604 1200 0 C REG_GND XUNREG_RESET 3 C4611 0.1u Q4606 MCH6305-TL-E-S B+ SWITCH (1.4A/32V) 6 5 2 1 8.3 R4609 10k MEGA model C4605 0.022u 16V R4605 6800 2 8 0 Q4604 2SC5846G0LS0 CHARGE CONTROL 0 Q4602 UNR32A3G0LS0 BATT_UNREG_CN C4613 XX R4610 1M R4607 1M 8.1 0.1 F006 (1.4A/32V) C 0 SHOE_UNREG C4612 1u 8 1 D4601 MA4ZD03001S0 R4615 XX SHOE_ON F005 8.3 4 OUT R4606 100k Q4601 2SB798-T1-DLDK -0.1 3 GND 8.1 8.3 Q4601, Q4602 CHARGE SWITCH VDD 4 8.3 8.3 N.C. 8 8 ACV_UNREG_CN R4608 XX S-80840CNNB-B8ZT2G RESET 1 R4603 10 1608 IC4601 2.8 6 5 7 8 B VTR_UNREG Q4603 MTM684110LS0 SWITCH 8.3 BATT/XEXT F001 3 SBO 8 AI 7 3 SIB 4 1.3 0.6 C4502 22p CH R4502 10k 9 1 2 DO 0.4 1 SIA 2.7 C4503 0.47u B 3 OUT 4 SOA 0.4 10 0.6 1 SE4501 SHOCK SENSOR IC4501 TA6038FNG (EL) SHOCK SENSOR AMP 2 C4501 22p CH R4611 1k MEGA model REG_GND 1 3 2 Q4605 UNR32A3G0LS0 SWITCH D4603 1SS361-TE85L BATT_UNREG D D D4602 XX REG_GND C4606 XX C4607 10u C4608 10u C4609 10u C4610 10u REG_GND R4612 XX R4613 XX REG_GND R4614 XX REG_GND E E F F G G VC-520 BOARD (18/20) H DC IN, CHARGE H XX MARK:NO MOUNT NO MARK:REC/PB MODE 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-23 VC-520 (18/20) 1 3 2 5 4 6 7 9 8 11 10 12 13 15 14 16 A Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E A MT4.3 DRV_UNREG MT5 / 15 MT_BL_UNREG 2.8 / 4.1 / 4.6 VTR2_UNREG 1.2 / 2.5 VTR_UNREG L4815 4.7uH D_1.8V B B C4858 XX CH1 4.6V L4813 4.7uH XX A_4.6V 4.7uH 2016 AU_4.6V 2016 A_4.6V XX REG_GND L4811 L4810 2016 C4853 4.7u C4855 4.7u R4844 C4851 XX C C REG_GND L4821 1uH MT_5.0V C4866 10u REG_GND CH2 MT_5V L4822 1uH DRV_MT_5.0V C4867 10u REG_GND 1u C4872 D CH1 4.6V 3 1.8/3VCTRL 1 CH3 2.8V 2 CH4 MT_4.3V CE GND VDD 4 R1114Q331D-TR-FA IC4802 3.3V REG CH2 MT5V VOUT 3 D 4.8 3.3 D_3.3V C4871 1u CH5 2.5V CH6 1.2V CH7 15.7V R4828 CH8 3.9V F XX XX R4825 R4823 R4845 R4817 R4815 R4816 560k 470p 47k C4827 R4826 D4805 MA2SD320G8S0 1 3 2 REG_GND NC (CP) VREG7 VREGD HVREG NF8 IN7 FB8 NF7 FB7 SOFT6 IN6 FB6 NF6 FB5 NF5 IN8 IN5 IN4 IN3 FB4 NF4 IN2 FB3 NF3 FB2 NF2 IN1 VREG8 SW4 PGND4 DC CONTROL, RESET, LANC DRIVE PVCC5 SW5 VCC2 PGND5 VRO PVCC6 SW6 VOUT PGND6 VBAT PVCC7 SW7 VCH PGND7 CS XRESET GATE8 F 2.2u A_2.5V C4865 4.7u 22uH C4834 2.2u 5V C4841 4.7u 10uH 2.2u CH6 1.2V 2.8V L4814 1uH C4842 4.7u 246 8 L4803 C4832 0 C4843 CLAMP_ON 10u R4806 1 2.5V C4844 4.7u 220p 10k 0.047u C4821 R4821 C4824 0.047u 100k C4819 R4819 0.1u 0.01u C4817 4 0 Q4804 SSM6N16FE(TPLR3) CLAMP C4854 4.7u C4856 4.7u CH8 3.9V L4805 L4809 4.7uH DRV_A_3.9V 22uH C4837 2.2u 1.2V C4850 4.7u C4845 4.7u H L4806 C4838 22uH 2.2u Non MEGA model R14.9/ P0 L4807 15.7V 15.7 33uH 4.8 C4847 4.7u 2 3 R4840 91k ± 0.5% 4.8 Q4802 MCH5819-TL-E SWITCHING 4 C4848 1u -15.7V 1 2 D4806 MA4ZD03001S0 6 5 4 R4832 4700 12.6 R4839 22k ± 0.5% 5 4 1 2.7 8.3 C4816 5 2 L4804 10uH C4836 2.2u 2.2 EVER_3.0V D_1.2V XX 135 7 6 3 2.8 1.2 4.3V G A_1.2V R4847 RB4801 100 22uH 2.2u Q4801 SCH2806-TL-E SWITCHING 3.9 J C4869 4.7u L4802 C4835 C4874 4.7u C4852 XX Q4807 UP04601G08S0 12V REG R12.6/ P0 R12/ P0 CAM_12VREG R11.9/P0.4 R4841 XX R4833 XX I 3 C4849 1u Q4803 2SA2078G0LS0 15V REG C4808 0.1u 4.7uH C4840 4.7u L4801 E11 A1 F10 F9 E10 D11D10C10 G9 C11 A11 B2 B6 A4 B5 B8 A7 A8 D2 D6 D3 H6 F8 E4 H7 K7 E5 L7 J6 J5 LANC_DC 4.7uH D_2.5V 4.6V REG6CTL VOUT6 VCONT6 VOUT5 VCONT5 STBY6 REG78CTL SCP I RT SW8 C5 D5 E6 L5 K6 L6 E7 H1 G2 G1 F3 A3 B4 A2 F5 J1 K1 L2 F6 D1 C2 B1 F7 E1 F2 F1 G3 L4 J4 L3 PVCC4 CT 0.1u DIN RST VCC3 FR_XRESET C4806 IC4801 BD9838GV-E2 SLOPE D4802 1SS357-TPH3 PGND3 CH8A SSREG6 100 BATT_IN VOUT SW3 CH8B SOFT 0.1u PVCC3 CH7L/H VR C4805 R4801 BATT_LI_3V CH5LH SCP9 VOUT 1u SW2 GND2 C4804 PVCC2 PGND2 XCTL2 MAS3132EGLS0 EVER_3.0V C4831 0.47u C4833 CH6LH WAKE_UP C4803 0.22u 1 1uH L4819 STB DATA_OUT EVER_3.0V D4801 3 L4817 CH5 2.5V GND DATA_IN BATT_UNREG 2 CH4 MT4.3V C4863 10u D4803 MA4ZD03001S0 SW1 LANC_OUT FR_EVER_SO E C4873 XX DRV_MT_4.3V 4 PGND1 LD C4870 4.7u C4830 1u VREGA CLK C4868 4.7u D4804 MA2SD320G8S0 R4824 0.0047U C4826 0.01u C4825 XX XX C4823 10k R4822 220p CH C4818 R4818 C4828 1u C4864 4.7u XX XX XX XX R4812 C4815 XX R4814 XX R4820 68k XX XX C4814 C4822 10u C4820 0.001u R4813 R4811 C4813 68k 0.0022u 10k 100p CH C4812 R4810 XX XX C4810 A_2.8V PVCC1 VOUT4 XCS_DD FR_EVER_SCK VTR_UNREG NF1 FB1 G AU_2.8V D_2.8V C4862 XX VCC1 SENSE 1.8/3VCTRL A_2.8V XX L4820 L11 L1 D9 E8 E9 J2 B11 H4 B10 H3 C9 H2 A10 G7 C4 C3 B3 D4 G6 K2 K3 K4 H5 J3 G5 A6 K5 G4 A5 A9 C4802 1u D_2.8V_1 C4829 2.2u R4802 XX XX 1uH L4818 1uH L4816 K8 L8 G8 C8 D8 D7 B7 C7 C6 F11 G10 B9 J7 J8 L9 L10 K11 H9 J9 J10 J11 G11 H11 H10 K10 K9 H8 E3 F4 E2 C4801 1u H R4807 XX XX C4807 R4804 R4808 C4811 XX XX E R4809 R4805 XX XX XX L4824 L4823 4.7uH CH3 2.8V MEGA model R4835 R14.9/P0 CAM_15/12V 15.7 L4808 22uH R15/P15.5 C4839 2.2u Q4805 2SA2078G0LS0 8.5V REG 8.5 0 EP_8.5V 15.7 C4857 2.2u 15.1 4 1 2 3 C4846 10u C4859 4.7u Q4806 R-15.3/ 2SC5846G0LS0 P-16.2 R-7.5/P0 3.9 C4809 10u ± 0.5% R-14.7/ P-16 R4803 3 6 Q4808 4 UP04401G08S0 R4834 22k 1 5 CL4802 4700 R-0.1/ P0.3 2 R4837 ± 0.5% R0.5/P0 J CAM_-7.5V R4836 R4831 100k R4838 ± 0.5% R4836 47k : Non MEGA model 100k : MEGA model R4838 15k : Non MEGA model 9.1k : MEGA model C4861 2.2u R4837 100k : Non MEGA model 220k : MEGA model K VTR_DD_ON 1.8/3VCTRL XLANC_ON LANC_IN LANC_OUT XLANC_PWR_ON LANC_SIG K LANC_DC Q4806, 4808 -7.5V REG VC-520 BOARD (19/20) DC/DC CONVERTER CAM_DD_ON XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE L L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-24 VC-520 (19/20) 1 3 2 5 4 6 9 8 7 10 11 12 14 13 15 16 A A R1012 ACV_GND 2 ACV_GND 3 ACV_GND 4 ACV_GND 5 N.C. 6 ACV_UNREG R1009 XX CN1009 REG_GND CN1006 0.001u C1020 1 0.001u C1019 2 BS 3 DATA1 4 REG_GND 5 8 10 ACV_UNREG FM_BIO2 FM_BIO3 11 BATT_XEXT 12 BATT_UNREG 13 BATT_UNREG FM_CLK 14 15 BATT_UNREG 16 BATT_UNREG 17 N.C. 18 BATT_SIG 19 BATT_UNREG_CN R1007 20 BATT_GND 21 BATT_GND 22 BATT_GND 23 BATT_GND 24 4 3 C1006 0.1u B BATT_SIG 220 BATT_GND D1001 EDZ-TE61-5.6B INS MPXOUT1 TRST_J 14 JNTRST_J 4 13 MPXOUT2 JTDI_J 13 JTDI_J 5 XDR_RESET 12 XDR_RESET JTMS_J 12 JTMS_J BOOTSEL 11 BOOTSEL JTCK_J 11 JTCK_J MNT1 10 MNT1 JRTCK_J 10 JRTCK_J MNT2 9 MNT2 JTDO_J 9 JTDO_J TXD 8 TXD MNT4 8 MNT4 FP-841 FLEXIBLE Page 4-33 of Level 2 DATA3 10 REG_GND 11 SCLK 12 MT_5.0V 4.8 BATT_UNREG IC1002 R1114Q291D-TR-FA 2.9V REG R1016 XX (ACV_GND_CN) REG_GND DATA2 8 9 BATT/XEXT VD1001 REG_GND 7 REG_GND 13 VCC 14 VCC REG_GND (BATT_GND_CN) CPC RXD 7 RXD MNT5 7 MNT5 SV_NOISE 6 SV_NOISE MNT6 6 MNT6 REG_GND 5 REG_GND MNT7 5 MNT7 TESTOUTN 4 TESTOUTN PI 4 PI D_2.8V 3 D_2.8V FE 3 FE (For Check) TESTOUTP 2 TESTOUTP TE 2 TE VTR_UNREG 1 JIG_UNREG CE 1 CE CN1013 CONTROL KEY BLOCK (PS26100) Page 4-34 of Level 2 CN1010 1 2 BOOT_MODE[3] 8 D_2.8V 7 BOOT_MODE_PORT0 N.C (Oberon_EXT) 6 CPC HOST_RXD 5 UART2_SI (For Check) HOST_TXD 4 UART2_SO AV_RXD 3 UART3_SI AV_TXD 2 UART3_SO GND 1 REG_GND XFM_IN 3 2 1 18P REG_GND 1 KEY_AD2 2 D_2.8V 3 QUICKREC_LED_VDD 4 REG_GND 5 D_2.8V 6 ZOOM_VR_AD 7 KEY_AD1 8 D_2.8V 9 XPOWER_SW 10 XMODE_SW 11 REG_GND 12 S/S 13 CHARGE_LED_VDD 14 XCHARGE_LED 15 XCAM_LED 16 XPHOTO_LED 17 MODE_LED_VDD 18 8P D_2.8V C1008 XX C1007 1u B 2.9V FM_PWR_ON R1017 XX D1007 XX XX 14 MPXOUT2 SDIO/DATA0 6 CN1011 14P MPXOUT1 0 9 ACV_UNREG VDD ACV_UNREG REG_GND FM_BS FM_BIO0 ACV_UNREG_CN 14P FM_BIO1 VOUT C 2 GND Page 4-34 of Level 2 3 1 7 ACV_UNREG FP-839 FLEXIBLE 0.001u C1017 DVD410E/DVD810/DVD810E (ACV_GND_CN) 4 CE B 0.001u C1018 B KEY_AD2 R1006 15 2.8 Q1003 DTA114EMFS6T2L LED DRIVE XQUICKREC_LED 0 2.8 ZOOM_VR_AD KEY_AD1 XPOWER_SW XMODE_SW C START/STOP R1008 EVER_3.0V 150 XCHARGE_LED XCAM_LED XPHOTO_LED R1018 220 D_2.8V 3 1 2 ACV_GND 1 XX LF1002 24P 0 CN1001 D1008 XX REG_GND REG_GND D D MEGA model Note: MIC901 is not included in VC-520 complete board. VD1005 REG_GND 3 VDD VOUT 4.8 C1001 0.1u B 4 REG_GND 3 MS_VCC 4 MS_VCC MSX_CLK 5 MS_SCLK CE GND 2.9V 1 2 C1002 1u 0 MS_PWR_ON C1003 XX MSX_BIO3 6 MSDATA3 XMS_IN 7 XMS_IN MSX_BIO2 8 MSDATA2 MSX_BIO0 9 MSDATA0 10 MSDATA1 MSX_BS 11 MS_BS REG_GND F REG_GND 6P CN1005 MIC_REG_GND 1 REG_GND INT_MIC_L 2 INT_MIC_L L MIC_REG_GND R 12 REG_GND 13 REG_GND CN1008 INT_MIC_R 4 5 INT_MIC_F 6 GND MIC_FR INT_MIC_F SIRCS_SIG 14 SIRCS_SIG PANEL_O/C 15 PANEL_O/C D_2.8V 16 D_2.8V 3 4 ID1 5 Page 4-29 of Level 2 2 3 UNREG 6 UNREG 7 ID2 8 STROBE 9 LANC 10 SHOE_CONT 11 GND 12 10P SHOE_MIC_FL REG_GND R1019 HOTSHOE_ID1 XX R1020 XX A/V R R1022 SHOE_UNREG XX HOTSHOE_ID2 AUDIO_L 1 LANC_SIG 2 S_GND 3 R1021 XX LANC_DC 4 S_C/D3_Pb 5 AUDIO_R 6 JACK_AD 7 VIDEO/AUDIO_GND 8 VIDEO/D3_Pr 9 S_Y/D3_Y 10 EXT_STROBE 2 D1002 XX 3 LANC_DC JACK_AD 1 XX RB1001 75 1 3 5 7 3 4 KEY_AD3 5 KEY_AD3 XBATT_VIEW 6 XBATT_VIEW BATT_LI_3V 7 BATT_LI_3V HI_XRESET 8 FR_XRESET ACCCESS_LED 9 XMS_ACC_LED D_2.8V 10 1 USB_D- 2 USB_D+ 3 ID 4 USB_GND 5 CN5801 Through the Flexible Flat Cable (FFC-089) Page 4-31 of Level 2 6 SP- SPREG_GND USB_VCC (USB) 8 MEGA model CK-192 SP+ 7 Page 4-30 of Level 2 H REG_GND 2 XX REG_GND G V_TO_PR C_TO_PB 5P 10P 1 VD1004 XX Y_TO_Y 2 4 6 8 S_C/D3_PB SP+ VD1003 REG_GND (SHOE_GND) S_Y/D3_Y REG_GND S_Y/D3_Y F VD1002 VIDEO/D3_PR CN1002 S_C/D3_PB R1029 XX C1021 XX C1011 XX VIDEO/D3_PR R1030 S_Y/D3_Y G CN5801 Through the Flexible Flat Cable (FFC-089) AUDIO_R_I/O FB1003 C1012 XX Page 4-33 of Level 2 CN1004 AUDIO_L_I/O FB1001 2 D1004 XX E LANC_SIG FB1002 REG_GND Non MEGA model CK-191 470p LANC_SIG 3 1 FP-842 FLEXIBLE C1015 C1016 470p SHOE_MIC_FR 2 MIC_FL FP-840 FLEXIBLE DVD115E/DVD310E/ DVD410E/DVD710/ DVD710E/DVD810/DVD810E 1 MIC_GND INT_MIC_R CN1012 D1006 XX C1010 XX 12P 3 MIC_REG_GND FRONT MSX_BIO1 1 11 12 2 MT_5.0V MIC901 MICROPHONE UNIT 13 14 REG_GND 0 R1005 XX E 1 VD1006 (SHOE_GND) 16P CN1003 REG_GND IC1001 R1114Q291D-TR-FA 2.9V REG USB_VCC USB_D-_CN USB_D+_CN USB_D2 4 1 3 LF1001 USB_D+ REG_GND LN1001 REG_GND DEW_AD LN1002 DEW_AD USB_DUSB_D+ C1005 100p CH H REG_GND D_2.8V XVBUS_DET 2.8 0 Q1001 UNR32A3G0LS0 USB DETECT I R1015 10k USB_VCC C1004 XX I REG_GND Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E Non MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E DVD110E/DVD115E/ J DVD310E/DVD410E J D_2.8V R1001 0 D_2.5V D_2.8V R1003 0 R1010 10k R1013 XX SYSTEM_AD R1023 15 1608 1/10W MEM_SEL1 GENERAL_AD MEM_SEL2 R1002 0 DVD610/DVD610E/ DVD710/DVD710E/ DVD810/DVD810E R1004 0 R1011 1200 REG_GND 5 R1014 0 REG_GND R1024 15 1608 1/10W 4 D1005 CL-335IRS2-X-TS (NIGHSHOT) 3 21 1.8 C1013 XX Q1002 2SC5663T2L LED DRIVE 0 IR_LED_ON R1025 3300 K REG_GND K REG_GND VC-520 BOARD (20/20) CONNECTOR L XX MARK:NO MOUNT NO MARK:REC/PB MODE L 05 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-25 VC-520 (20/20) 4-3. PRINTED WIRING BOARDS Link VC-520 BOARD (SIDE A) COMMON NOTE FOR PRINTED WIRING BOARDS DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 VC-520 BOARD (SIDE B) 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS (ENGLISH) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • Chip parts. Transistor • • : Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation B (JAPANESE) プリント図共通ノート 【プリント図ノート】 ・ ・ :無鉛半田を使用しています。 :基板 :フレキシブル配線板 見ている面側のパターン。 :裏側のパターン (他のパターンについては表示されていません) ・スルーホールは省略。 ・プリント図には,本機で使用していない部品が記載されている 場合があります。 ・Cはパネル表示名称。 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-35 Diode 6 5 4 4 5 6 5 C E 4 4 3 5 3 3 1 23 1 2 3 3 2 1 1 2 3 3 2 1 2 1 2 1 2 1 4 3 3 4 6 5 4 4 5 6 2 1 1 2 3 3 2 1 2 2 1 3 2 5 4 3 3 4 5 4 1 1 2 3 2 4 1 1 6 54 VC-520 (8 layers) : Uses unleaded solder. Note: LF1002, R1009 and R1012 have the same mount location. When you replace, since either LF1002 or R1009 and R1012 are used, please refer to schematic diagram and electrical parts list. H6 C6 B6 A6 J7 H7 C7 B7 A7 K8 J8 H8 G8 F8 E8 D8 C8 B8 A8 K9 J9 H9 G9 F9 E9 D9 C9 B9 A9 C1220 4 3 2 D4603 1 C1215 R1020 R1022 C4612 C E C1702 CL1201 P 14 2.8V R1781 4 24 23 D1001 3 4.6V D4602 2 X1701 1 R1829 C1728 C2034 C1703 R1717 R1007 C2024 R1782 R1838 C2003 C2043 C1008 R1017 2.5V B C4846 C1222 13 C4844 2 D1002 3 3 4 IC1002 3 1 2 2 J6 K7 R1209 2 X1201 1 CN1006 K6 C1213 1 A5 R4613 A4 B5 C4840 A3 B4 C5 L4801 B3 C4 C1006 L4805 C3 D4 C4842 R1016 AC3 AB3 AA3 Y3 W3 V3 U3 T3 R3 P3 N3 M3 L3 K3 J3 H3 G3 F3 E3 D3 C3 B3 A3 AR4 AP4 AN4 AM4 AL4 AK4 AJ4 AH4 AG4 AF4 AE4 AD4 AC4 AB4 AA4 Y4 W4 V4 U4 T4 R4 P4 N4 M4 L4 K4 J4 H4 G4 F4 E4 D4 C4 B4 A4 AR5 AP5 AN5 AM5 E5 D5 C5 B5 A5 A6 AP7 AN7 AM7 AJ7 AH7 AG7 AF7 AE7 AD7 AC7 AB7 AA7 Y7 W7 V7 U7 T7 R7 P7 N7 M7 L7 K7 J7 H7 G7 D7 C7 B7 A7 AP8 AN8 AM8 AN6 AM6 AJ8 AH8 AG8 AF8 AE8 AD8 AC8 AB8 AA8 Y8 W8 V8 U8 T8 R8 P8 N8 M8 L8 K8 J8 H8 G8 D6 D8 C8 B8 A8 AR9 AP9 AN9 AM9 AJ9 AH9 AG9 AF9 AE9 Y9 R9 W9 V9 U9 T9 AR10 AP10 AN10 AM10 AJ10 AH10 AG10 AF10 Y10 W10 V10 U10 T10 AR11 AP11 AN11 AM11 AJ11 AH11 AG11 Y11 W11 V11 U11 T11 W12 V12 U12 AJ12 AH12 AJ13 AH13 AR14 AP14 AN14 AM14 AJ14 AH14 AR15 AP15 AN15 AM15 AJ15 AH15 AG15 AR16 AP16 AN16 AM16 AJ16 AH16 AG16 AF16 AE16 R1868 L9 K9 K10 J9 AR17 AP17 AN17 AM17 AJ17 AH17 AG17 AF17 AE17 AD17 AJ18 AH18 AG18 AF18 AE18 AD18 AR19 AP19 AN19 AM19 AJ19 AH19 AG19 AF19 AE19 AD19 IC1701 G9 D9 R1869 R1870 C10 B10 A10 C11 B11 A11 H12 G12 D12 C12 B12 A12 H13 G13 D13 C13 B13 A13 H14 G14 D14 C14 B14 A14 H15 G15 D15 C15 B15 A15 A16 L16 K16 J16 H16 G16 D16 C16 B16 M17 L17 K17 J17 H17 G17 D17 C17 B17 M18 L18 K18 J18 H18 G18 D18 C18 B18 A18 M19 L19 K19 J19 H19 G19 D19 C19 B19 A19 L20 K20 AJ20 AH20 AG20 AF20 AE20 J20 J21 H20 G20 D20 C20 B20 CL1717 A_2.8V C2026 C2032 A20 AJ21 AH21 AG21 AJ22 AH22 H21 G21 D21 C21 B21 A21 H22 G22 D22 C22 B22 A22 AR23 AP23 AN23 AM23 AJ23 AH23 AR24 AP24 AN24 AM24 AJ24 AH24 W24 V24 U24 AR25 AP25 AN25 AM25 AJ25 AH25 AG25 Y25 W25 V25 U25 T25 AR26 AP26 AN26 AM26 AJ26 AH26 AG26 AF26 Y26 W26 V26 U26 T26 AR27 AP27 AN27 AM27 AJ27 AH27 AG27 AF27 AE27 AA27 Y27 W27 V27 U27 T27 R27 L27 K27 J27 H27 G27 D27 C27 B27 A27 AR28 AP28 AN28 AM28 AJ28 AH28 AG28 AF28 AE28 AD28 AC28 AB28 AA28 Y28 W28 V28 U28 T28 R28 P28 N28 M28 L28 K28 J28 H28 G28 D28 C28 B28 A28 AR29 AP29 AN29 AM29 AJ29 AH29 AG29 AF29 AE29 AD29 AC29 AB29 AA29 Y29 W29 V29 U29 T29 R29 P29 N29 M29 L29 K29 J29 H29 G29 D29 C29 B29 A29 D30 C30 B30 A30 D31 C31 B31 A31 AR32 AP32 AN32 AM32 AL32 AK32 AJ32 AH32 AG32 AF32 AE32 AD32 AC32 AB32 AA32 Y32 W32 V32 U32 T32 R32 P32 N32 M32 L32 K32 J32 H32 G32 F32 E32 D32 C32 B32 A32 AR33 AP33 AN33 AM33 AL33 AK33 AJ33 AH33 AG33 AF33 AE33 AD33 AC33 AB33 AA33 Y33 W33 V33 U33 T33 R33 P33 N33 M33 L33 K33 J33 H33 G33 F33 E33 D33 C33 B33 A33 AR34 AP34 AN34 AM34 AL34 AK34 AJ34 AH34 AG34 AF34 AE34 AD34 AC34 AB34 AA34 Y34 W34 V34 U34 T34 R34 P34 N34 M34 L34 K34 J34 H34 G34 F34 E34 D34 C34 B34 A34 AR35 AP35 AN35 AM35 AL35 AK35 AJ35 AH35 AG35 AF35 AE35 AD35 AC35 AB35 AA35 Y35 W35 V35 U35 T35 R35 P35 N35 M35 L35 K35 J35 H35 G35 F35 E35 D35 C35 B35 A35 H23 G23 D23 C23 B23 A23 H24 G24 D24 C24 B24 A24 J25 H25 G25 D25 C25 B25 A25 K26 J26 H26 G26 D26 C26 B26 A26 C2017 AR31 AP31 AN31 AM31 CL1801 C2038 R1847 R1871 FB1804 C2012 R1739 C2013 R1737 R2015 R1855 R1854 1 13 CN1011 R1853 R1858 R1852 R1857 R1851 FB1803 R1873 2 14 1 R1872 13 CN1009 2 14 R1850 D_2.8V 5 R2011 3 1 C2045 10 C1709 R1722 R1012 R1783 D_1.2V R1011 D_3.3V R1010 R1013 R1735 1 1 C1723 R1859 A_2.8V R1726 D_1.2V 7 RB1701 1 8 2 R1787 2 CN1003 R1725 C1714 C1717 C1724 R1768 C2039 R1860 R1785 C1729 C1715 C1716 2 8 1 RB1706 7 P R1009 R1789 C1725 7 RB1703 1 8 2 F005 R1846 R2017 C1730 F003 F004 CL1204 CL1203 A17 AR21 AP21 AN21 AM21 C1731 16 A9 D10 D11 AR22 AP22 AN22 AM22 C2002 FB1802 C2033 C1726 R1844 R2105 B9 G10 G11 FB1801 R1864 CL1804 CL1805 C9 H10 H11 J15 AR18 AP18 AN18 AM18 H9 J10 J11 5V B Note: IC2101 is not supplied, but this is included in VC-520 complete board. 7 RB1705 1 8 2 E Q1701 E B R1006 AR12 AP12 AN12 AM12 AR13 AP13 AN13 AM13 AA9 C6 C 2 8 RB1707 1 7 Q1003 AP6 VD1001 2 AR6 F006 4.3V D1008 C2006 C2019 B6 AR7 AR8 C4606 1.2V 9 R1841 L4806 CN1013 AD3 2 AE3 18 AF3 CN1001 AG3 1 AH3 R1018 AJ3 R1008 AK3 1 AL3 C1017 AN3 AM3 4 AP3 C1018 AR3 4 R1840 3 A2 D1007 A1 B2 1 B1 C2 C4609 C1 D2 F002 D1 E2 LF1002 E1 F2 C4610 F1 G2 F001 G1 H2 2 H1 J2 3 J1 K2 C4608 K1 L2 C1019 L1 M2 C1020 M1 N2 C4607 N1 P2 8 P1 R2 2 R1 T2 1 T1 U2 L4802 U1 V2 7 V1 W2 CN1010 W1 Y2 1 Y1 AA2 2 AA1 AB2 CN1002 AB1 AC2 C4845 AC1 AD2 C4841 AD1 AE2 L4807 AE1 AF2 L4804 AF1 AG2 R2001 AG1 AH2 C2031 AH1 AJ2 C1706 AJ1 AK2 C2015 R1830 AK1 C4843 U14 V14 W14 C1007 1 L4803 D3 Q4605 E3 IC1201 C2025 P13 R13 T13 U13 V13 W13 2 D1006 1 F3 H5 R2016 P12 R12 T12 U12 V12 W12 3 6 G3 H4 J5 1 H3 J4 K5 Q4606 J3 K4 R2014 N13 P11 R11 T11 U11 V11 3 18 4 K3 C1219 3 A2 R4609 B2 AR30 AP30 AN30 AM30 15 1 2 R4611 C2 C4613 D2 R4610 E2 C1225 F2 R1205 G2 AL2 R1867 R2104 C1001 C1011 R1019 C1202 C1201 C1223 FB1202 C1221 H2 AL1 10 05 C1214 C1204 R1203 J2 AN2 AM2 R1862 R1801 C2101 R1005 R1021 R4612 7 1 RB1704 8 2 N12 P10 R10 T10 U10 V10 T8 T7 U8 U7 R1865 2 IC10011 3 4 C2922 C2923 K2 R1211 C1211 R1014 VD1006 A1 AN1 AM1 R1721 C1016 B1 C1705 R1724 VD1005 C1 C1208 R1784 C1015 D1 CL1202 R2012 C2010 2 8 RB1806 1 7 FB1001 FB1002 E1 AP2 C2014 R2013 C2042 M13 N11 P9 R9 V9 V8 R1863 C1003 CN4401 F1 AP1 R1744 C1002 1 G1 R1206 C1217 C1233 4IC1202 3 1 2 L1201 C1212 R1803 R1843 B14 C14 K14 L14 J14 C13 D13 E13 F13 G13 H13 R2108 C2109 A14 C2105 R2106 A13 A12 B13 C12 D12 E12 F12 G12 H12 J13 K13 J12 K12 L13 G11 H11 L12 G10 H10 J11 K11 L11 J10 K10 L10 N10 P8 R8 P7 D_1.8V R1845 R1030 FB1003 L2902 R1029 7 RB1001 1 8 2 C1021 FB1203 2 1 D1004 AR2 R1842 R1866 L2903 11 C1012 AR1 R1745 T9 R7 D_1.8V CL1802 CL1803 C2911 C C2102 R1208 17 CN3101 L4808 CL2102 C2916 C2932 Q2901 VD1003 VD1002 C2924 CL2104 R2904 C2904 9 5 10 1 62 7 3 84 CN1012 VD1004 B E C1209 R1219 C1227 L1203 R1220 A C1210 7 RB1807 1 8 2 R2901 CL2101 CL2103 A/V R V7 T6 T4 T5 U6 U4 U5 V6 V5 V3 W3 V4 T3 V2 U1 V1 13 12 1 W2 48 R2902 C2933 W1 C2909 C2920 C2907 D1005 (NIGHTSHOT) C2919 U3 T2 C2928 C2921 R2903 U2 R1024 5 R1023 IC2901 R1202 C1231 C2801 C2802 C2812 C2806 R2807 R2808 C1216 AR20 AP20 AN20 AM20 L2904 H1 R1746 U9 R6 M11 M10 IC2101 K4 K5 L4 L5 P6 R5 M4 N4 N5 P4 P5 R4 M5 K3 L3 N3 P3 R3 R1218 C2808 C2103 C11 D11 E11 F11 B11 C10 D10 E10 F10 F8 F7 F4 F6 G4 G5 H4 H5 J4 J5 F5 B10 C9 D9 B9 B8 C8 D8 E9 B7 C7 D7 E8 E7 F9 C6 D6 E6 B4 C4 C5 D4 D5 E4 E5 B5 B6 A3 B3 C3 D3 E3 F3 G3 H3 J3 K2 L2 M2 N2 P2 M3 K1 L1 J1 B12 P12 N12 P11 N11 P10 N10 A1 A2 B2 B1 C1 C2 D2 G2 H2 F2 C2106 24 R2 C2929 25 C2104 L2905 36 37 R1212 1 2 A_1.2V C2107 M12 A9 B9 N9 P9 7 RB2804 1 8 2 A8 B8 IC2801 N8 P8 RB2102 R2905 C2912 C2930 J1 C2838 AU_4.6V C2108 C2848 C2918 C2902 C2903 C2905 C2927 C2915 C2832 J2 C2906 C2926 7 1 8 RB29042 B C1013 C2901 2 1 Q1002 E C1206 C1207 C1205 R2107 C2847 E2 1 7 8 RB5102 2 7 1 RB2901 8 2 CAM_15/12V K1 FB1201 8 7 3 L2802 C2112 16 2 K10 J10 H10 G10 F10 E10 D10 C10 B10 A10 C2917 2 8 RB2902 1 7 A C2831 C2828 R2809 12 CN1008 R1204 R1201 C1203 1 2 C2823 C2839 C2844 A_2.8V C2910 4 C2833 A R1025 1 D_2.8V A7 B7 N7 P7 N6 P6 C2834 C2836 C1230 CAM_-7.5V 7 8 D_1.8V 2 1 2 C2851 L2805 2 8 1 RB5101 7 2 8 RB2805 1 7 C2811 C2809 L2801 A6 B6 B12 A12 A5 B5 N5 N3 N4 P5 P4 P3 C2830 C2829 FB1204 C1228 C2850 5 C C2818 AU_2.8V P14 N14 M14 L14 K14 J14 H14 G14 F14 E14 D14 C14 B14 A14 A4 B4 B11 A11 A3 B3 P13 N13 M13 L13 K13 J13 H13 G13 F13 E13 D13 C13 B13 A13 A2 B2 C2 D2 F2 G2 K2 N2 P2 P1 M2 L2 J2 H2 F1 J1 K1 N1 M1 C2841 CN3102 C2843 C2845 7 1 RB2903 8 2 2 8 1 RB5103 7 C2840 B L1 R4413 L2803 Q4402 H1 G1 E1 R2803 1 R2802 2 D1 C2835 E2 A1 B1 C1 Q2801 CN4402 C2837 B B10 A10 C2817 C2814 R5173 7 1 8 RB44022 D1005 27 C2816 E 1 D4402 4 C2822 C2820 C2842 3 1 C2821 15 CN1203 A_2.8V R2806 C2819 C2805 R2818 C2825 R2805 C2824 R2804 VD5102 6 4 Q5101 3 1 30 29 8 R2819 C2815 C E 5 RB2803 7 24 1 CN1201 R5165 C5107 C VD5101 2 28 7 RB28011 8 2 C1720 R5172 2 CN1005 C1010 6 1 23 CN5101 2 1 R4614 VC-520 BOARD (SIDE A) C R1736 LN1001 LN1002 1-874-566- 11 21 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-37 VC-520 (SIDE A) VC-520 (8 layers) : Uses unleaded solder. C2427 6 U1 6 V1 6 Y1 AA16 A15 B15 D15 E15 5 U1 5 V1 5 Y1 AA15 4 U1 4 V1 4 Y1 AA14 D13 E13 D12 E12 A11 B11 D11 E11 3 U1 3 V1 3 Y1 AA13 2 U1 2 V1 2 Y1 AA12 1 U1 1 V1 1 Y1 AA11 A10 B10 A9 B9 A8 B8 D10 E10 0 U1 0 V1 0 Y1 AA10 D9 E9 U9 V9 Y9 9 AA D8 E8 U8 V8 Y8 8 AA A7 B7 D7 E7 U7 V7 Y7 7 AA A6 B6 D6 E6 U6 V6 Y6 6 AA A5 B5 D5 E5 F5 G5 H5 J5 K5 L5 M5 N5 P5 R5 T5 U5 V5 Y5 5 AA A4 B4 D4 E4 F4 G4 H4 J4 K4 L4 M4 N4 P4 R4 T4 U4 V4 Y4 4 AA A2 B2 C2 D2 E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 R2 T2 U2 V2 W2 Y2 2 AA A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 R1 T1 U1 V1 W1 Y1 1 AA IC2401 A3 B3 Y3 3 AA R2439 C2415 2 8 1 RB2401 7 R2408 R5316 C5414 C5314 R5318 R5314 R5315 C5313 R5320 C5412 C5411 C5409 1 C5407 F6 G6 H6 A5 B5 C5 D5 E5 F5 G5 H5 A4 B4 C4 D4 E4 F4 G4 H4 A3 B3 C3 D3 E3 F3 G3 H3 A2 B2 C2 D2 E2 F2 G2 H2 A1 B1 C1 D1 E1 F1 G1 H1 R2428 C5404 R5405 R5403 C5405 4 1 C5301 IC5302 E B B C5403 E R3112 C Q3104 Q3102 4 6 Q3101 1 3 Q5401 R5301 D5401 D5301 R5402 C5402 C C Q3103 E B R3111 R3121 C3120 Q3106 E B C3105 DRV_MT_5.0V A DRV_MT_4.3V R3102 C3109 C3104 R3104 R3101 1-874-5668 R5404 R5415 R5310 R5308 D5302 C5308 R3109 C R3110 C3121 R3105 L4404 G1 R5309 7 RB3103 1 8 2 1 L3103 R3120 3 1 Q3105 4 6 C3116 C C3103 G2 A1 B1 C1 D1 E1 F1 E C4405 L4403 R2418 R2419 R3122 C3102 C4410 A2 B2 C2 D2 E2 F2 R5307 D3101 C4406 2 8 RB2402 1 7 C3101 G3 B 14 H7 E6 R2423 R2411 1 8 8 H8 G7 D6 3 R2427 2 8 1 RB3102 7 G8 F7 C6 C4408 1 Q2401 4 6 4 IC5102 5 C5311 C5406 R5319 R5409 C5312 R5410 R5322 4 1 C3119 1 F8 E7 B6 G4 A3 B3 C3 D3 E3 F3 C C5303 R5304 C3108 C2411 R2421 E8 D7 A6 A4 B4 C4 D4 E4 F4 Q5301 R5306 CN1012 7 Y1 AA17 D16 E16 D8 C7 G5 B E C5302 12 8 Y1 AA18 D17 E17 F17 G17 H17 J17 7 K1 7 L1 7 M1 7 N1 7 P1 7 R1 7 T1 7 U1 7 V1 A16 B16 C8 B7 G6 A5 B5 C5 D5 E5 F5 11 D18 E18 F18 G18 H18 J18 8 K1 8 L1 8 M1 8 N1 8 P1 8 R1 8 T1 8 U1 8 V1 A17 B17 A12 B12 R5411 Q5102 IC5101 B IC3102 C2424 R2407 C3118 B8 A7 A6 B6 C6 D6 E6 F6 6 A18 B18 IC4401 A8 Q3107 9 Y1 AA19 C4402 R4405 R5303 4 C C2428 C2410 C2420 R2405 R5414 IC5103 R5139 R5140 8 B E C4403 G7 MT_5.0V_LD R3119 A6 IC5301 A7 B7 C7 D7 E7 F7 C5316 1 B6 A5 C5305 R5302 C5306 C5304 3 C6 B5 C5317 CL3104 1 D6 C5 A_2.8V C2409 C2404 A13 B13 R3107 13 12 E6 D5 R5311 R5305 48 F6 E5 FB4401 R3103 G6 F5 R5406 R3115 IC3101 G5 D_2.8V FB4302 7 RB4301 1 8 2 24 A4 7 1 RB3101 8 2 25 B4 D14 E14 12 D_2.8V C3112 36 37 C4 C3110 F4 2 8 RB1802 1 7 C3107 G4 C5307 C5410 A H4 2 8 RB1803 1 7 L3102 A3 7 RB3104 1 8 2 A2 B3 L3101 B2 C3 C3113 C2 C3115 D2 E3 D3 IC4302 E4 D4 R4411 E2 F3 C4302 R4410 F2 G3 D_2.8V C3106 A1 C4404 B1 54 R4261 C1 2 8 RB1805 1 7 L4402 D1 2 8 RB1801 1 7 C4204 2 8 1 RB4403 7 E1 R4233 R4234 C4208 C4232 R4201 R5312 R5313 R3114 D19 C19 B19 A19 1 L5101 R3108 AC19 AB19 AA19 Y19 R4202 R3113 D18 C18 B18 A18 13 D17 C17 B17 A17 AC18 AB18 AA18 Y18 C5315 4 D16 C16 B16 A16 AC17 AB17 AA17 Y17 L5301 C5408 C4237 5 AC16 AB16 AA16 Y16 13 IC5401 C4303 D15 C15 B15 A15 C5309 24 C4305 AC15 AB15 AA15 Y15 R5136 C5105 C5413 R4241 D14 C14 B14 A14 G2 A14 B14 R5412 5 C4202 D13 C13 B13 A13 P14 N14 M14 L14 K14 R4207 R4409 C2425 R5138 8 D12 C12 B12 A12 P13 N13 M13 L13 K13 AC14 AB14 AA14 Y14 11 21 5 Q2402 1 4 R2420 D_2.8V R2417 C2419 C2414 R2429 2 C2417 X4901 3 5 P12 N12 M12 L12 K12 AC13 AB13 AA13 Y13 R2412 CL4911 CL4910 CL4912 CL4909 C2423 C5401 8 AC12 AB12 AA12 Y12 C2407 R1004 R1003 C4915 R4928 R4935 C2401 D_1.2V R1001 C2402 C2429 C4913 R1002 R5137 D11 C11 B11 A11 H3 R2402 C5101 R5174 C5104 P11 N11 M11 L11 K11 IC4301 IC4303 AC11 AB11 AA11 Y11 A19 B19 R4930 FB4301 D9 C9 B9 A9 D10 C10 B10 A10 A20 B20 C20 D20 E20 F20 G20 H20 J20 0 K2 0 L2 0 M2 0 N2 0 P2 0 R2 0 T2 0 U2 0 V2 0 W2 0 Y2 AA20 R4929 C4308 D8 C8 B8 A8 IC4201 C4246 C4210 F1 7 RB5402 1 8 2 R5135 P10 N10 M10 L10 K10 A21 B21 C21 D21 E21 F21 G21 H21 J21 1 K2 1 L2 1 M2 1 N2 1 P2 1 R2 1 T2 1 U2 1 V2 1 W2 1 Y2 AA21 R4907 C5310 C5106 R4206 AC9 AB9 AA9 Y9 R4406 CL2404 R4909 R4936 C4207 D6 C6 B6 A6 D7 C7 B7 A7 CL2405 3 R5317 7 RB5401 1 2 8 C D5 C5 B5 A5 AC6 AB6 AA6 Y6 AC7 AB7 AA7 Y7 Q4401 IC4904 1 C4238 F4 E4 D4 C4 B4 A4 AC10 AB10 AA10 Y10 C2408 1 C4212 R4259 C4213 J4 H4 G4 C4311 C4912 C4910 R4926 C4917 C4217 L4 K4 H2 H6 R4903 4 R4214 C4225 C4214 AC4 AB4 AA4 Y4 W4 V4 U4 T4 R4 P4 N4 M4 AC21 AB21 AA21 Y21 W21 V21 U21 T21 R21 P21 N21 M21 L21 K21 J21 H21 G21 F21 E21 D21 C21 B21 A21 G1 H5 CL2406 5 27 28 C4247 C4226 C4227 C4203 C4201 C4216 R4223 C4215 C4228 C4229 R4136 C4231 C4211 L4202 C4135 C4126 F3 E3 D3 C3 B3 A3 C4411 3 R4937 7 1 RB4903 8 2 C4914 1 CL4903 CL4906 CL4904 CL4905 L1 1 K11 J1 1 H11 G11 F1 1 E1 1 D11 C11 B1 1 A1 1 L1 0 K10 J1 0 H10 G10 F1 0 E1 0 D10 C10 B1 0 A1 0 C8 B8 A8 L9 K9 J9 H9 G9 F9 E9 D9 C9 B9 A9 L8 K8 J8 L7 K7 J7 R4934 C4907 3 6 1 J3 H3 G3 R2440 C4916 C7 B7 A7 C6 B6 A6 C5 B5 A5 C4 B4 A4 4 IC4905 C4905 IC4901 L6 K6 J6 L5 K5 J5 L4 K4 J4 CL4908 R4933 R4910 L3 K3 2 8 RB1804 1 7 3 1 IC4902 4 5 C4904 2 8 RB4904 1 7 L3 K3 J3 H3 G3 F3 E3 D3 C3 B3 A3 R4914 L2 K2 J2 H2 G2 F2 E2 D2 C2 B2 A2 R4915 R4911 AC3 AB3 AA3 Y3 W3 V3 U3 T3 R3 P3 N3 M3 D_1.2V FB2401 C4906 R1015 C1005 1 LF1001 CL4902 L1 K1 J1 H1 G1 F1 E1 D1 C1 B1 A1 R4942 R4941 C1004 Q1001 B C4908 F2 E2 D2 C2 B2 A2 C4209 C4240 X4201 R4232 C4230 C4249 R4257 M12 L12 K12 J12 H12 G12 F12 E12 D12 C12 B12 A12 B10 A10 M11 L11 K11 J11 H11 G11 F11 E11 D11 C11 B11 A11 M10 L10 M9 L9 M8 L8 R4847 D_2.5V D_2.8V 3IC4903 1 4 5 1 4 D4806 3 R4615 C4611 R4839 7 R4913 E C4223 C4220 C4128 7 1 RB4101 8 2 FB4104 7 RB4901 1 8 2 5 C4909 F1 E1 D1 C1 B1 A1 J2 H2 G2 C4903 CL4901 2 IC46011 3 4 J1 H1 G1 L2 K2 R4908 VOUT 2 8 RB4905 1 7 E AC23 AB23 AA23 Y23 W23 V23 U23 T23 R23 P23 N23 M23 L23 K23 J23 H23 G23 F23 E23 D23 C23 B23 A23 CL2407 C4820 C4849 C4848 L1 K1 AC2 AB2 AA2 Y2 W2 V2 U2 T2 R2 P2 N2 M2 AC20 AB20 AA20 Y20 W20 V20 U20 T20 R20 P20 N20 M20 L20 K20 J20 H20 G20 F20 E20 D20 C20 B20 A20 C4902 6 4 Q4804 1 3 C4301 B AC22 AB22 AA22 Y22 W22 V22 U22 T22 R22 P22 N22 M22 L22 K22 J22 H22 G22 F22 E22 D22 C22 B22 A22 C4854 5 R4215 7 1 RB4401 8 2 C4124 R4137 C4138 C4127 C4107 B8 A8 B7 A7 B9 A9 B6 A6 B5 A5 IC4101 B4 A4 M5 L5 M7 L7 C4132 C4248 C4310 Q4802 2 8 RB4902 1 7 2 3 B3 A3 2 8 RB4801 1 7 R4901 5 4 8 C4131 C4139 C4505 05 C4130 R4826 1 R4932 B 2 Q4803 E B R4831 C4861 Q4806 C 4 2 C4503 1 H1 3 2 CL4111 FB4103 L4814 C4856 C4827 R4820 R4818 C4818 R4804 C4822 R4918 R4502 3 C4129 FB4203 AC1 AB1 AA1 Y1 W1 V1 U1 T1 R1 P1 N1 M1 R4138 CL4105 4 E C CN1004 R4501 C4206 CL4112JL4212 CL4107 E C4911 C4506 R4203 C4233 C4222 AC8 AB8 AA8 Y8 R4260 C4134 C4825 LANC_DC R4917 10 C4111 CL4109 R4205 CL2409 R4823 CL4802 1 6 R4222 C4250 AC5 AB5 AA5 Y5 FB4204 CL2408 VOUT R4841 IC4501 R4225 FB4201 L4815 C4826 C4118 CL4108 R4817 R4824 B C R4608 C4852 R4840 4 3 SE4501 5 FB4205 C4117 Q4805 R4835 1 Q4807 6 C4863 C4867 C4866 C4501 R4240 C4219 C4809 R4813 C4858 C4814 R4806 R4825 R4814 R4805 C4140 M6 L6 C4141 M4 L4 C4116 C4806 R4815 C4808 M3 L3 M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 B1 A1 D4802 A C4502 C4121 C4105 C4114 C4110 C4112 C4864 C4815 C4807 C4823 C4119 R4801 C4901 R4832 FB4206 R4256 C4205 C4109 C4873 L4818 C4805 R4803 L11 K11 J11 H11 G11 F11 E11 D11 C11 B11 A11 L10 K10 J10 H10 G10 F10 E10 D10 C10 B10 A10 L9 K9 J9 H9 G9 F9 E9 D9 C9 B9 A9 L8 K8 J8 H8 G8 F8 E8 D8 C8 B8 A8 R4828 C4857 C4874 R4833 C4122 C4136 R4838 3 1 Q4808 4 5 C4859 L4817 C C4872 C4871 R4837 C4123 C4120 C4804 C E 7 RB4102 1 8 2 M2 L2 K2 J2 H2 G2 F2 E2 D2 C2 B2 A2 C4803 C4847 C4828 R4836 B 2 IC48021 3 4 R4834 Q4602 C4108 D4201 R4822 D4804 C L4822 C4838 C4868 3 R4802 R4807 C4810 C4801 R4808 R4819 R4821 C4811 C4824 L7 K7 J7 H7 G7 F7 E7 D7 C7 B7 A7 C4837 C4833 R4605 B Q4601 L4823 R4816 C4832 E C4870 L4816 C4862 L4102 R4809 R4811 R4810 C4812 C4816 D4801 R4604 R4603 L4821 1 2 5 4 Q4603 8 1 R4606 L6 K6 J6 H6 G6 F6 E6 D6 C6 B6 A6 4 L5 K5 J5 H5 G5 F5 E5 D5 C5 B5 A5 3 C L4 K4 J4 H4 G4 F4 E4 D4 C4 B4 A4 1 D4601 L1 K1 J1 H1 G1 F1 E1 D1 2 R4607 C4834 C4605 Q4604 L3 K3 J3 H3 G3 F3 E3 D3 C3 B3 A3 D4805 C4831 B E L4824 IC4801 L2 K2 J2 H2 G2 F2 E2 D2 C2 B2 A2 2 C4835 1 B1 A1 D4803 C4821 C4813 R4812 C4819 C4839 3 C4836 6 C4137 4 C4106 CL4134 CL4138 CL4140 CL4119 CL4136 L4819 C4817 C4802 Q4801 4 C4830 FL4103 1 FB4105 CL4139 CL4135 CL4137 CL4141 R4845 R4931 L4820 C4865 C4869 1 R4221 R4219 3 2 C4218 C4829 3 2 50 EVER_3.0V L4809 C4851 2 C4101 C4850 R4844 4 FL4101 3 L4813 L4810 D_2.8V C4239 4 1 C4102 C4855 C4304 C4236 L4103 C4853 L4811 C4234 FB4102 R4248 R4247 2 4 L4203 C4104 FB4106 3 FB4101 CN4103 FL4104 1 2 4 1 FL4102 3 C4113 1 51 4 DRV_A_3.9V 5 A_2.8V A_2.5V R5321 Note: IC4301 and IC4303 have the same mounted location. When you replace, since either IC4301 or IC4303 are used, please refer to schematic diagram and electrical parts list. VC-520 BOARD (SIDE B) CN1004 (USB) Note: IC4302 and IC4901 are not supplied, but they are included in VC-520 complete board. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 4-38 VC-520 (SIDE B) 5. REPAIR PARTS LIST (ENGLISH) NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • CAPACITORS: uF: µF • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD... When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • Color Indication of Appearance Parts Example: (SILVER) : Cabinet’s Color (Silver) : Parts Color (JAPANESE) 【使用上の注意】 • ここに記載されている部品は, 補修用部品であるため, 回路図及び セットに付いている部品と異なる場合があります。 • -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合 があります。 • *印の部品は常備在庫しておりません。 • コンデンサの単位でuFはμFを示します。 • 抵抗の単位Ωは省略してあります。 金 被:金属被膜抵抗。 サンキン:酸化金属被膜抵抗。 • インダクタの単位でuHはμHを示します。 • 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ A..., μPA..., μPB..., μPC..., μPD...を示します。 • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-1 お願い 図面番号で部品を指定するときは基板名又はブロック を併せて指定してください。 0印の部品,または0印付の点線で囲まれた部品は, 安全性を維持するために,重要な部品です。 従って交換時は, 必ず指定の部品を使用してください。 • 外装部品色表示 例: (SILVER):セットの色を表す。 (Silver) : 部品の色を表す。 VC-520 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. A-1439-718-A VC-520 BOARD, COMPLETE (SERVICE) (DVD110E) A-1439-719-A VC-520 BOARD, COMPLETE (SERVICE) (DVD115E) A-1439-720-A VC-520 BOARD, COMPLETE (SERVICE) (DVD610/DVD610E) A-1439-739-A VC-520 BOARD, COMPLETE (SERVICE) (DVD310E) A-1439-741-A VC-520 BOARD, COMPLETE (SERVICE) (DVD710) A-1439-742-A VC-520 BOARD, COMPLETE (SERVICE) (DVD710E) A-1439-744-A VC-520 BOARD, COMPLETE (SERVICE) (DVD410E) A-1439-745-A VC-520 BOARD, COMPLETE (SERVICE) (DVD810) A-1439-746-A VC-520 BOARD, COMPLETE (SERVICE) (DVD810E) ********************** (IC2101, IC4302 and IC4901 are not supplied, but they are included in VC-520 complete board.) < CAPACITOR > C1001 C1002 C1005 C1006 C1007 1-125-777-11 1-165-908-11 1-164-874-11 1-125-777-11 0.1uF 10% 10V 1uF 10% 10V 100PF 5% 50V 0.1uF 10% 10V (DVD410E/DVD810/DVD810E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD410E/DVD810/DVD810E) C1015 C1016 C1017 C1018 C1019 1-164-935-11 1-164-935-11 1-164-937-11 1-164-937-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 470PF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C1020 C1201 C1202 C1203 C1204 1-164-937-11 1-164-866-11 1-164-866-11 1-107-826-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 47PF 47PF 0.1uF 0.001uF 10% 5% 5% 10% 10% 50V 50V 50V 16V 50V C1205 C1206 C1207 C1208 C1209 1-125-777-11 1-125-777-11 1-125-777-11 1-107-826-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 10V 16V 10V C1211 C1212 C1213 1-125-777-11 CERAMIC CHIP 1-112-300-91 CERAMIC CHIP 1-100-567-81 CERAMIC CHIP C1213 1-164-937-11 CERAMIC CHIP C1214 1-125-777-11 CERAMIC CHIP 10% 10V 10% 10V 10% 25V (DVD710/DVD810) 0.001uF 10% 50V (EXCEPT DVD710/DVD810) 0.1uF 10% 10V C1216 C1220 C1221 C1222 C1225 1-119-750-11 1-127-760-11 1-125-777-11 1-125-777-11 1-127-820-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 4.7uF 0.1uF 0.1uF 4.7uF 20% 10% 10% 10% 10% 6.3V 6.3V 10V 10V 16V C1227 C1228 1-165-908-11 CERAMIC CHIP 1-119-750-11 TANTAL. CHIP 1uF 22uF 10% 20% 10V 6.3V 0.1uF 4.7uF 0.01uF DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-15 Description C1231 C1233 C1702 1-127-760-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 1-164-937-11 CERAMIC CHIP 4.7uF 1uF 0.001uF 10% 10% 10% 6.3V 10V 50V C1703 C1705 C1706 C1709 C1714 1-164-850-11 1-127-760-11 1-164-937-11 1-164-937-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10PF 4.7uF 0.001uF 0.001uF 0.001uF 0.5PF 10% 10% 10% 10% 50V 6.3V 50V 50V 50V C1715 C1716 C1717 C1720 C1723 1-165-908-11 1-165-908-11 1-164-937-11 1-100-567-81 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 1uF 0.001uF 0.01uF 4.7uF 10% 10% 10% 10% 10% 10V 10V 50V 25V 6.3V C1724 C1725 1-165-908-11 CERAMIC CHIP 1uF 10% 10V 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C1726 C1728 C1729 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP Part No. C1730 C2002 C2003 C2006 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C2010 C2012 C2013 C2014 C2015 1-164-937-11 1-164-937-11 1-164-937-11 1-164-937-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C2017 C2019 C2024 C2025 C2026 1-164-937-11 1-125-777-11 1-164-937-11 1-164-937-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 50V 10V 50V 50V 50V C2031 C2032 C2033 C2034 C2038 1-164-937-11 1-164-937-11 1-164-937-11 1-164-937-11 1-165-884-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 2.2uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 6.3V C2039 C2042 C2043 C2045 C2101 1-165-884-11 1-165-884-11 1-165-884-11 1-127-760-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 2.2uF 2.2uF 2.2uF 4.7uF 0.1uF 10% 10% 10% 10% 10% 6.3V 6.3V 6.3V 6.3V 10V C2102 C2103 C2104 C2105 C2106 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 10V C2109 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C1731 VC-520 Ref. No. Part No. Description C2112 C2401 C2402 C2404 1-131-862-91 1-164-937-11 1-164-937-11 1-164-937-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.001uF 0.001uF 0.001uF 20% 10% 10% 10% 4V 50V 50V 50V Ref. No. C2407 C2408 C2411 C2414 C2415 1-164-937-11 1-164-937-11 1-164-937-11 1-164-937-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.001uF 0.1uF 10% 10% 10% 10% 10% 50V 50V 50V 50V 10V C2417 C2419 C2427 C2428 C2429 1-125-777-11 1-125-777-11 1-125-889-11 1-125-889-11 1-125-889-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 2.2uF 2.2uF 2.2uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 10V C2801 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) C2824 C2825 C2829 C2830 C2833 C2834 C2802 C2805 C2806 C2808 C2835 C2836 C2837 C2839 C2840 C2809 C2811 C2812 C2814 C2815 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) C2841 C2842 C2843 C2845 C2847 C2816 C2817 C2818 C2820 C2821 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) C2848 C2851 C2901 C2902 C2903 C2904 C2823 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-16 C2905 Part No. Description 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD110E/DVD610/DVD610E) 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD110E/DVD610/DVD610E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD110E/DVD610/DVD610E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD110E/DVD610/DVD610E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD110E/DVD610/DVD610E) VC-520 Ref. No. C2906 Part No. Description 1-127-760-11 CERAMIC CHIP C2907 1-127-760-11 CERAMIC CHIP C2909 1-119-923-11 CERAMIC CHIP C2910 1-125-777-11 CERAMIC CHIP C2911 1-165-989-11 CERAMIC CHIP C2915 1-125-777-11 CERAMIC CHIP C2916 1-127-760-11 CERAMIC CHIP C2919 1-100-567-81 CERAMIC CHIP C2920 1-125-777-11 CERAMIC CHIP C2921 1-165-908-11 CERAMIC CHIP C2922 1-165-989-11 CERAMIC CHIP C2923 1-127-760-11 CERAMIC CHIP C2924 1-125-777-11 CERAMIC CHIP C2926 1-125-777-11 CERAMIC CHIP C2927 1-125-777-11 CERAMIC CHIP C2928 1-127-760-11 CERAMIC CHIP C2929 1-127-760-11 CERAMIC CHIP C2930 1-125-777-11 CERAMIC CHIP C2932 1-125-777-11 CERAMIC CHIP C2933 1-107-819-11 CERAMIC CHIP C3101 1-100-567-81 CERAMIC CHIP Ref. No. 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 0.047uF 10% 10V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 10uF 10% 6.3V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 0.01uF 10% 25V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 1uF 10% 10V (DVD110E/DVD610/DVD610E) 10uF 10% 6.3V (DVD110E/DVD610/DVD610E) 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 4.7uF 10% 6.3V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 0.1uF 10% 10V (DVD110E/DVD610/DVD610E) 0.022uF 10% 16V (DVD110E/DVD610/DVD610E) 0.01uF 10% 25V C3102 C3103 C3104 C3105 * C3106 1-100-567-81 1-100-567-81 1-165-908-11 1-125-777-11 1-100-741-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 1uF 0.1uF 560PF 10% 10% 10% 10% 5% 25V 25V 10V 10V 50V C3108 C3110 C3112 C3113 C3115 1-165-989-11 1-127-760-11 1-125-889-11 1-127-760-11 1-165-989-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 4.7uF 2.2uF 4.7uF 10uF 10% 10% 10% 10% 10% 6.3V 6.3V 10V 6.3V 6.3V C3116 C3118 C3120 C3121 C4101 1-125-777-11 1-165-989-11 1-100-567-81 1-127-760-11 1-165-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 0.01uF 4.7uF 1uF 10% 10% 10% 10% 10% 10V 6.3V 25V 6.3V 10V C4102 C4104 C4105 C4106 C4107 1-165-908-11 1-165-989-11 1-164-937-11 1-164-937-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 10uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 10V 6.3V 50V 50V 50V DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-17 Part No. Description C4108 C4109 C4110 C4111 C4112 1-164-937-11 1-125-777-11 1-125-777-11 1-127-760-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 4.7uF 4.7uF 10% 10% 10% 10% 10% 50V 10V 10V 6.3V 6.3V C4113 C4114 C4116 C4117 C4118 1-127-760-11 1-165-989-11 1-165-989-11 1-127-760-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 10uF 10uF 4.7uF 4.7uF 10% 10% 10% 10% 10% 6.3V 6.3V 6.3V 6.3V 6.3V C4119 C4120 C4121 C4122 C4123 1-125-777-11 1-125-777-11 1-100-567-81 1-125-777-11 1-100-567-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.01uF 0.1uF 0.01uF 10% 10% 10% 10% 10% 10V 10V 25V 10V 25V C4124 C4127 C4128 C4129 C4130 1-125-777-11 1-125-777-11 1-164-874-11 1-164-937-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 100PF 0.001uF 0.1uF 10% 10% 5% 10% 10% 10V 10V 50V 50V 10V C4131 C4132 C4134 C4135 C4136 1-125-777-11 1-125-777-11 1-125-777-11 1-127-760-11 1-165-989-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 4.7uF 10uF 10% 10% 10% 10% 10% 10V 10V 10V 6.3V 6.3V C4138 C4140 C4141 C4201 C4202 1-164-864-11 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 39PF 0.1uF 0.1uF 0.1uF 0.1uF 5% 10% 10% 10% 10% 50V 10V 10V 10V 10V C4203 C4204 C4205 C4206 C4207 1-125-777-11 1-100-567-81 1-164-850-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 10PF 0.1uF 0.1uF 10% 10% 0.5PF 10% 10% 10V 25V 50V 10V 10V C4208 C4209 C4210 C4211 C4212 1-125-777-11 1-125-777-11 1-165-989-11 1-165-989-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 10uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 6.3V 6.3V 10V C4213 C4214 C4215 C4216 C4217 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 10V C4218 C4219 C4222 C4223 C4225 1-164-937-11 1-164-850-11 1-164-850-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 10PF 10PF 0.1uF 0.1uF 10% 0.5PF 0.5PF 10% 10% 50V 50V 50V 10V 10V C4226 C4227 C4228 C4229 C4230 1-125-777-11 1-125-777-11 1-107-819-11 1-107-819-11 1-107-819-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.022uF 0.022uF 0.022uF 10% 10% 10% 10% 10% 10V 10V 16V 16V 16V C4231 C4232 1-164-882-11 CERAMIC CHIP 1-125-777-11 CERAMIC CHIP 220PF 0.1uF 5% 10% 16V 10V VC-520 Ref. No. Part No. Description Ref. No. C4236 C4237 C4238 1-125-777-11 CERAMIC CHIP 1-125-777-11 CERAMIC CHIP 1-125-777-11 CERAMIC CHIP 0.1uF 0.1uF 0.1uF 10% 10% 10% 10V 10V 10V C4240 C4246 C4248 C4249 C4250 1-100-567-81 1-165-908-11 1-165-908-11 1-100-567-81 1-125-891-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 1uF 1uF 0.01uF 0.47uF 10% 10% 10% 10% 10% 25V 10V 10V 25V 10V C4301 C4302 C4303 C4304 C4305 1-165-908-11 1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 10V C4310 C4311 C4402 C4403 C4404 1-165-908-11 1-125-777-11 1-119-923-11 1-165-989-11 1-165-989-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 0.1uF 0.047uF 10uF 10uF 10% 10% 10% 10% 10% 10V 10V 10V 6.3V 6.3V C4406 C4408 C4410 C4411 C4501 1-165-897-11 1-165-989-11 1-165-989-11 1-107-819-11 1-164-858-11 TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 10uF 10uF 0.022uF 22PF 20% 10% 10% 10% 5% 10V 6.3V 6.3V 16V 50V C4502 C4503 C4505 C4506 C4605 1-164-858-11 1-125-891-11 1-164-939-11 1-127-760-11 1-107-819-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22PF 0.47uF 0.0022uF 4.7uF 0.022uF 5% 10% 10% 10% 10% 50V 10V 50V 6.3V 16V C4607 C4608 C4609 C4610 C4611 1-165-875-11 1-165-875-11 1-165-875-11 1-165-875-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 10uF 10uF 0.1uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 10V C4612 C4801 C4802 C4803 C4804 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V 1-165-908-11 CERAMIC CHIP 1uF 10% 10V 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C4805 C4806 C4808 C4809 C4812 1-125-777-11 1-125-777-11 1-125-777-11 1-165-989-11 1-164-874-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 10uF 100PF 10% 10% 10% 10% 5% 10V 10V 10V 6.3V 50V C4813 C4816 C4817 C4818 C4819 1-164-939-11 1-125-777-11 1-100-567-81 1-164-882-11 1-119-923-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0022uF 0.1uF 0.01uF 220PF 0.047uF 10% 10% 10% 5% 10% 50V 10V 25V 16V 10V C4820 C4821 C4822 C4824 C4825 1-164-937-11 1-164-933-11 1-165-989-11 1-119-923-11 1-100-567-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 220PF 10uF 0.047uF 0.01uF 10% 10% 10% 10% 10% 50V 50V 6.3V 10V 25V C4826 C4827 C4828 1-100-581-81 CERAMIC CHIP 1-164-935-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 0.0047uF 10% 470PF 10% 1uF 10% 50V 50V 10V DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-18 Part No. Description C4829 C4830 1-127-861-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 2.2uF 1uF 10% 10% 16V 10V C4831 C4832 C4833 C4834 C4835 1-107-823-11 1-125-889-11 1-125-889-11 1-125-889-11 1-125-889-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47uF 2.2uF 2.2uF 2.2uF 2.2uF 10% 10% 10% 10% 10% 16V 10V 10V 10V 10V C4836 C4837 C4838 C4839 C4840 1-125-889-11 1-125-889-11 1-125-889-11 1-125-889-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 2.2uF 2.2uF 2.2uF 2.2uF 4.7uF 10% 10% 10% 10% 10% 10V 10V 10V 10V 6.3V C4841 C4842 C4843 C4844 C4845 1-127-760-11 1-127-760-11 1-165-989-11 1-127-760-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 4.7uF 10uF 4.7uF 4.7uF 10% 10% 10% 10% 10% 6.3V 6.3V 6.3V 6.3V 6.3V C4846 C4847 C4848 C4849 C4850 1-165-989-11 1-127-820-11 1-100-591-91 1-100-591-91 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 4.7uF 1uF 1uF 4.7uF 10% 10% 10% 10% 10% 6.3V 16V 25V 25V 6.3V C4853 C4854 C4855 C4856 C4857 1-127-760-11 1-127-760-11 1-127-760-11 1-127-760-11 1-125-889-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 4.7uF 4.7uF 4.7uF 2.2uF 10% 10% 10% 10% 10% 6.3V 6.3V 6.3V 6.3V 10V C4859 C4861 C4863 C4864 C4865 1-127-820-11 1-125-889-11 1-165-989-11 1-127-760-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 2.2uF 10uF 4.7uF 4.7uF 10% 10% 10% 10% 10% 16V 10V 6.3V 6.3V 6.3V C4866 C4867 C4868 C4869 C4870 1-165-989-11 1-165-989-11 1-127-760-11 1-127-760-11 1-127-760-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 4.7uF 4.7uF 4.7uF 10% 10% 10% 10% 10% 6.3V 6.3V 6.3V 6.3V 6.3V C4871 C4872 C4874 C4901 C4906 1-165-908-11 CERAMIC CHIP 1uF 10% 10V 1-165-908-11 CERAMIC CHIP 1uF 10% 10V 1-127-820-11 CERAMIC CHIP 4.7uF 10% 16V (DVD110E/DVD115E/DVD610/DVD610E) 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C4907 C4908 C4909 C4910 C4911 1-164-852-11 1-100-567-81 1-125-777-11 1-125-777-11 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 12PF 0.01uF 0.1uF 0.1uF 0.1uF 5% 10% 10% 10% 10% 50V 25V 10V 10V 10V C4913 C4914 C4915 C4916 C4917 1-100-567-81 1-100-567-81 1-125-777-11 1-125-777-11 1-100-567-81 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.1uF 0.1uF 0.01uF 10% 10% 10% 10% 10% 25V 25V 10V 10V 25V C5101 C5104 C5105 1-127-760-11 CERAMIC CHIP 1-113-682-11 TANTAL. CHIP 1-125-891-11 CERAMIC CHIP 4.7uF 33uF 0.47uF 10% 20% 10% 6.3V 10V 10V VC-520 Ref. No. C5106 C5301 C5302 C5303 C5304 C5305 C5306 C5307 C5308 C5309 C5311 C5313 C5314 C5315 C5402 C5403 C5404 C5405 C5406 C5407 C5409 C5410 Part No. Description Ref. No. 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-165-908-11 CERAMIC CHIP 1uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V 1-127-772-81 CERAMIC CHIP 0.033uF 10% 10V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V (DVD110E/DVD115E/DVD610/DVD610E) 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V (DVD110E/DVD115E/DVD610/DVD610E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD110E/DVD115E/DVD610/DVD610E) 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V (DVD110E/DVD115E/DVD610/DVD610E) 1-164-935-11 CERAMIC CHIP 470PF 10% 50V (DVD110E/DVD115E/DVD610/DVD610E) 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V (DVD110E/DVD115E/DVD610/DVD610E) 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (DVD110E/DVD115E/DVD610/DVD610E) 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V (DVD110E/DVD115E/DVD610/DVD610E) Part No. Description CN1006 1-815-762-51 CONNECTOR, FFC/FPC 14P (DVD410E/DVD810/DVD810E) CN1008 1-779-330-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 12P (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) CN1009 1-815-762-51 CONNECTOR, FFC/FPC 14P CN1010 1-779-328-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 8P CN1012 1-815-794-13 CONNECTOR (MULTIPLE) (A/V R) * CN1013 1-821-546-61 CONNECTOR, FFC/FPC (ZIF) 18P CN1201 1-779-338-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 28P (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) CN1203 1-779-332-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 16P (DVD110E/DVD115E/DVD610/DVD610E) * CN3101 1-779-333-51 CONNECTOR, FFC/FPC 18P CN3102 1-779-339-51 FFC/CONNECTOR, FPC (LIF (NON-ZFF)) 30P * CN4103 1-819-860-51 * CN4401 1-816-643-51 CN4402 1-779-328-51 * CN5101 1-815-763-51 CONNECTOR, FPC (ZIF) 51P FFC/CONNECTOR, FPC (LIF) 10P FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 8P CONNECTOR, FFC/FPC 24P < DIODE > D1001 * D1005 D4601 D4603 * D4801 D4802 D4803 D4804 D4805 D4806 * D5301 * D5302 * D5401 8-719-074-67 6-501-598-01 8-719-074-08 8-719-421-67 DIODE DIODE DIODE DIODE EDZ-TE61-5.6B CL-335IRS-X-TS (NIGHTSHOT) MA4ZD03001S0 MA132WK (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 6-501-928-01 DIODE MAS3132EGLS0 8-719-027-76 8-719-074-08 6-500-813-01 6-500-813-01 8-719-074-08 DIODE DIODE DIODE DIODE DIODE 1SS357-TPH3 MA4ZD03001S0 MA2SD32008S0 MA2SD32008S0 MA4ZD03001S0 6-501-947-01 DIODE MA2S1110G8S0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 6-501-947-01 DIODE MA2S1110G8S0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 6-501-947-01 DIODE MA2S1110G8S0 (DVD110E/DVD115E/DVD610/DVD610E) < FUSE > 0 F001 0 F002 0 F003 0 F004 0 F005 1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21 0 F006 1-576-406-21 FUSE, MICRO (1608) (1.4A/32V) FUSE, MICRO (1608) (1.4A/32V) FUSE, MICRO (1608) (1.4A/32V) FUSE, MICRO (1608) (1.4A/32V) FUSE, MICRO (1608) (1.4A/32V) FUSE, MICRO (1608) (1.4A/32V) (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) < FERRITE BEAD > C5413 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V (DVD110E/DVD115E/DVD610/DVD610E) < CONNECTOR > * CN1001 1-815-763-51 * CN1002 1-779-329-51 CN1003 1-779-332-51 * CN1004 1-821-723-11 * CN1005 1-779-327-51 CONNECTOR, FFC/FPC 24P FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 10P FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 16P CONNECTOR, SQUARE TYPE (USB) 5P (USB) FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 6P FB1001 FB1002 FB1003 FB1201 FB1202 1-400-927-31 1-400-927-31 1-400-833-21 1-400-331-11 1-400-723-11 BEAD, FERRITE (1005) BEAD, FERRITE (1005) SMD EMI FERRITE FERRITE, EMI (SMD) (1005) INDUCTOR, FERRITE BEAD (1005) FB1203 1-400-331-11 FERRITE, EMI (SMD) (1005) FB1204 1-400-331-11 FERRITE, EMI (SMD) (1005) FB1801 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) • Refer to page 5-1 for mark 0. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-19 Ver. 1.1 2008.01 The changed portions from Ver. 1.0 are shown in blue. Ref. No. Part No. VC-520 Description Ref. No. FB1802 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) FB1803 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) (DVD410E/DVD810/DVD810E) FB1804 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) (DVD410E/DVD810/DVD810E) FB2401 1-400-619-11 BEAD, FERRITE (CHIP) (1608) FB4101 1-400-619-11 BEAD, FERRITE (CHIP) (1608) FB4102 1-400-619-11 BEAD, FERRITE (CHIP) (1608) FB4103 1-400-619-11 BEAD, FERRITE (CHIP) (1608) IC5302 IC5401 Part No. Description 8-759-693-13 IC NJM12904V (TE2) (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 8-759-637-96 IC uPD16877MA-6A5-E2 (DVD110E/DVD115E/DVD610/DVD610E) < COIL > L1201 L2801 FB4104 FB4105 FB4106 FB4201 FB4203 1-400-619-11 1-400-619-11 1-414-864-11 1-400-619-11 1-400-619-11 BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) FERRITE, EMI (SMD) (1608) BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) L2802 FB4204 FB4205 FB4206 FB4301 FB4302 1-414-864-11 1-469-109-21 1-469-109-21 1-400-619-11 1-400-619-11 FERRITE, EMI (SMD) (1608) FERRITE, EMI (SMD) (1608) FERRITE, EMI (SMD) (1608) BEAD, FERRITE (CHIP) (1608) BEAD, FERRITE (CHIP) (1608) L2805 L2803 1-400-588-11 INDUCTOR 10uH 1-400-588-11 INDUCTOR 10uH (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-400-588-11 INDUCTOR 10uH (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-400-588-11 INDUCTOR 10uH (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-400-588-11 INDUCTOR 10uH (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) L2902 1-400-588-11 INDUCTOR L2903 1-400-588-11 INDUCTOR L2904 1-400-588-11 INDUCTOR L2905 1-400-588-11 INDUCTOR L3101 1-400-588-11 INDUCTOR L3102 L3103 L4102 L4103 L4202 1-400-588-11 1-400-588-11 1-400-588-11 1-400-588-11 1-400-588-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10uH 10uH 10uH 10uH 10uH L4402 L4403 L4404 L4801 L4802 1-469-553-21 1-469-549-21 1-469-549-21 1-456-137-11 1-457-049-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 4.7uH 1uH 1uH 22uH 10uH L4803 L4804 L4805 L4806 L4807 1-416-669-11 1-457-049-21 1-456-137-11 1-416-669-11 1-456-138-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22uH 10uH 22uH 22uH 33uH L4808 L4809 L4811 L4813 L4814 1-456-137-11 1-469-553-21 1-469-553-21 1-469-553-21 1-469-549-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22uH 4.7uH 4.7uH 4.7uH 1uH L4815 L4817 L4818 L4819 L4820 1-469-553-21 1-469-549-21 1-469-549-21 1-469-553-21 1-469-553-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 4.7uH 1uH 1uH 4.7uH 4.7uH L4821 L4822 L4823 L4824 L5101 1-469-549-21 1-469-549-21 1-469-553-21 1-469-549-21 1-469-553-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 1uH 1uH 4.7uH 1uH 4.7uH L5301 1-400-588-11 INDUCTOR 10uH FB4401 1-400-619-11 BEAD, FERRITE (CHIP) (1608) < IC > * IC1001 * IC1002 * IC1201 * IC1202 * IC1202 * IC1701 IC2101 * IC2401 * IC2801 6-708-445-01 IC R1114Q291D-TR-FA 6-708-445-01 IC R1114Q291D-TR-FA (DVD410E/DVD810/DVD810E) 6-711-079-01 IC R2J45015AHBGW0 6-708-445-01 IC R1114Q291D-TR-FA (DVD110E/DVD115E/DVD610/DVD610E) 6-708-447-01 IC R1114Q341D-TR-FA (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 8-753-300-16 (Not supplied) 6-709-936-01 6-710-768-01 IC IC IC IC * IC3101 IC3102 * IC4101 * IC4201 IC4302 8-753-242-24 8-759-693-13 8-753-235-82 8-753-274-88 (Not supplied) IC IC IC IC IC * IC4303 6-710-459-01 IC W9864G6GH-7S-ER10 * IC4401 6-710-787-01 IC R2A30212LG-W00B (DVD110E/DVD115E/DVD610/DVD610E) 6-709-970-01 IC BD6310GU-E2 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 6-707-601-01 IC TA6038FNG (EL) 6-702-519-01 IC S-80840CNNB-B8ZT2G * IC2901 * IC4401 IC4501 IC4601 CXD4218GG-TL K5R1213ACB-AK75T R8A01015ABGTLV NN12923B-BB (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 6-710-463-01 IC NN12922A-BB (DVD110E/DVD610/DVD610E) IC IC IC IC IC CXM3018R-T4 NJM12904V (TE2) CXA2725GA-T4 CXD5052GG-T6 39VF1601-70-4C-B3KE-GG013T * IC4801 IC4802 IC4901 IC5101 IC5102 6-710-736-01 6-703-977-01 (Not supplied) 6-706-663-01 8-759-693-13 BD9838GV-E2 R1114Q331D-TR-FA MB95005BGL-G-110-ERE1 NJW5210RB1 NJM12904V (TE2) IC5103 * IC5301 8-759-693-13 IC NJM12904V (TE2) 6-708-988-01 IC LV8053LG-TLM-E (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-20 10uH (DVD110E/DVD610/DVD610E) 10uH (DVD110E/DVD610/DVD610E) 10uH (DVD110E/DVD610/DVD610E) 10uH (DVD110E/DVD610/DVD610E) 10uH VC-520 Ref. No. Part No. Description Ref. No. < LINE FILTER > LF1001 1-457-223-11 COMMON MODE CHOKE COIL * LF1002 1-457-217-21 COMMON MODE CHOKE COIL < TRANSISTOR > * Q1001 Q1002 Q1003 * Q1701 Q2801 Q2901 6-551-766-01 6-550-102-01 6-550-238-01 6-551-771-01 8-729-056-75 TRANSISTOR UNR32A3G0LS0 TRANSISTOR 2SC5663T2L TRANSISTOR DTA114EMFS6T2L TRANSISTOR UNR31AFG0LS0 TRANSISTOR MCH3211-TL-E (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 8-729-056-75 TRANSISTOR MCH3211-TL-E (DVD110E/DVD610/DVD610E) UP04501G08S0 2SB1462-Q 2SB1462-Q 2SB1462-Q * Q3101 Q3102 Q3103 Q3104 6-551-847-01 8-729-425-50 8-729-425-50 8-729-425-50 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q3105 * Q3106 Q3107 * Q4401 * Q4402 8-729-054-48 6-551-766-01 6-551-184-01 6-551-760-01 6-551-766-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q4601 * Q4602 Q4603 * Q4604 * Q4605 8-729-101-07 6-551-766-01 6-551-442-01 6-551-758-01 6-551-766-01 TRANSISTOR 2SB798-DL TRANSISTOR UNR32A3G0LS0 TRANSISTOR TPCP8301 (T5RSONYF) TRANSISTOR 2SC5846G0LS0 TRANSISTOR UNR32A3G0LS0 (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) Q4606 Q4801 Q4802 * Q4803 Q4804 * Q4805 * Q4806 Q4807 * Q4808 * Q5101 * Q5102 * Q5301 Q5401 UP04601008S0 UNR32A3G0LS0 MCH6305-TL-E-S UNR31A3G0LS0 UNR32A3G0LS0 6-551-184-01 TRANSISTOR MCH6305-TL-E-S (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 6-550-813-01 TRANSISTOR SCH2806-TL-E 6-550-533-01 TRANSISTOR MCH5819-TL-E 6-551-836-01 TRANSISTOR 2SA2078G0LS0 6-550-180-01 TRANSISTOR SSM6N16FE (TPLR3) 6-551-836-01 TRANSISTOR 2SA2078G0LS0 6-551-758-01 TRANSISTOR 2SC5846G0LS0 8-729-054-48 TRANSISTOR UP04601008S0 (DVD110E/DVD115E/DVD610/DVD610E) 6-551-846-01 TRANSISTOR UP04401G08S0 6-551-850-01 TRANSISTOR UP04116G08S0 6-551-758-01 TRANSISTOR 2SC5846G0LS0 6-551-758-01 TRANSISTOR 2SC5846G0LS0 (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 6-550-758-01 TRANSISTOR DTC113TMFS6T2L (DVD110E/DVD115E/DVD610/DVD610E) Part No. Description R1008 R1010 R1011 R1014 R1015 1-218-943-11 1-218-965-11 1-218-954-11 1-218-990-81 1-218-965-11 RES-CHIP RES-CHIP RES-CHIP SHORT CHIP RES-CHIP R1018 R1023 R1024 R1025 R1201 1-218-945-11 1-216-799-11 1-216-799-11 1-218-959-11 1-218-990-81 RES-CHIP 220 5% 1/16W METAL CHIP 15 5% 1/10W METAL CHIP 15 5% 1/10W RES-CHIP 3.3K 5% 1/16W SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) R1202 R1203 R1212 R1218 1-218-937-11 1-218-971-11 1-218-937-11 1-218-990-81 R1002 R1004 R1006 R1007 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-21 1/16W 1/16W 1/16W 5% 1/16W R1717 R1721 R1722 R1724 R1725 R1726 1-220-180-11 1-208-911-11 1-218-941-11 1-208-683-11 1-208-683-11 RES-CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP 620 10K 100 1K 1K 5% 0.5% 5% 0.5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W R1768 R1803 R1829 R1830 R1838 1-218-953-11 1-218-953-11 1-218-977-11 1-218-962-11 1-218-973-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 100K 5.6K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1840 R1841 R1842 R1843 R1844 1-218-944-11 1-218-944-11 1-218-944-11 1-218-944-11 1-218-942-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 180 180 180 180 120 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R1850 1-218-942-11 RES-CHIP R1855 1-218-942-11 RES-CHIP R1865 R2104 R2106 1-218-942-11 RES-CHIP 1-218-933-11 RES-CHIP 1-218-953-11 RES-CHIP R2407 R2408 R2411 R2412 R2417 1-218-960-11 1-218-944-11 1-218-944-11 1-218-960-11 1-208-709-11 R2418 R2419 R2420 R2802 1-208-873-81 1-208-873-81 1-208-873-81 1-218-961-11 R2803 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD310E/DVD410E) 1-218-990-81 SHORT CHIP 0 (DVD610/DVD610E/ DVD710/DVD710E/DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 1-218-931-11 RES-CHIP 15 5% 1/16W 1-218-945-11 RES-CHIP 220 5% 1/16W 5% 5% 5% RES-CHIP 47 5% 1/16W RES-CHIP 33K 5% 1/16W RES-CHIP 47 5% 1/16W SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 1-218-953-11 RES-CHIP 1K 5% 1/16W < RESISTOR > R1001 150 10K 1.2K 0 10K R2818 R2819 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 120 5% 1/16W (DVD410E/DVD810/DVD810E) 120 5% 1/16W (DVD410E/DVD810/DVD810E) 120 5% 1/16W 22 5% 1/16W 1K 5% 1/16W 3.9K 180 180 3.9K 12K 5% 5% 5% 5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W METAL CHIP 270 0.5% 1/16W METAL CHIP 270 0.5% 1/16W METAL CHIP 270 0.5% 1/16W RES-CHIP 4.7K 5% 1/16W (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-218-973-11 RES-CHIP 47K 5% 1/16W (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-218-963-11 RES-CHIP 6.8K 5% 1/16W (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1-218-975-11 RES-CHIP 68K 5% 1/16W (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) VC-520 Ref. No. Part No. Description R2901 1-218-969-11 RES-CHIP R2902 1-218-961-11 RES-CHIP R2903 1-218-961-11 RES-CHIP R2904 1-218-973-11 RES-CHIP R3102 R3105 R3107 1-218-975-11 1-208-935-11 1-208-922-11 R3107 1-208-721-11 R3108 R3109 R3110 R3112 R3113 1-218-961-11 1-218-957-11 1-220-876-81 1-218-953-11 1-220-876-81 R3114 R3115 R3119 R3120 1-220-876-81 1-208-943-11 1-218-957-11 1-208-861-81 Ref. No. 22K 5% 1/16W (DVD110E/DVD610/DVD610E) 4.7K 5% 1/16W (DVD110E/DVD610/DVD610E) 4.7K 5% 1/16W (DVD110E/DVD610/DVD610E) 47K 5% 1/16W (DVD110E/DVD610/DVD610E) RES-CHIP 68K 5% 1/16W METAL CHIP 100K 0.5% 1/16W METAL CHIP 30K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) METAL CHIP 39K 0.5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) Part No. Description R4413 R4501 R4502 R4603 1-218-944-11 1-218-977-11 1-218-965-11 1-216-797-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP R4604 R4605 R4606 R4607 R4609 1-218-954-11 1-218-963-11 1-218-977-11 1-218-989-11 1-218-965-11 RES-CHIP 1.2K 5% 1/16W RES-CHIP 6.8K 5% 1/16W RES-CHIP 100K 5% 1/16W RES-CHIP 1M 5% 1/16W RES-CHIP 10K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) R4610 R4801 R4803 R4806 1-218-989-11 RES-CHIP 1M 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-953-11 RES-CHIP 1K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-941-81 RES-CHIP 100 5% 1/16W 1-218-961-11 RES-CHIP 4.7K 5% 1/16W 1-216-789-11 METAL CHIP 2.2 5% 1/10W R4810 R4811 R4818 R4819 R4820 1-218-965-11 1-218-975-11 1-218-965-11 1-218-977-11 1-218-975-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP R4821 R4824 R4826 R4831 R4832 1-218-965-11 1-218-986-11 1-218-973-11 1-218-977-11 1-218-961-11 RES-CHIP 10K 5% 1/16W RES-CHIP 560K 5% 1/16W RES-CHIP 47K 5% 1/16W RES-CHIP 100K 5% 1/16W RES-CHIP 4.7K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) R4834 R4835 1-218-969-11 RES-CHIP 22K 5% 1/16W 1-218-990-81 SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 1-208-927-11 METAL CHIP 47K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-208-935-11 METAL CHIP 100K 0.5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-208-935-11 METAL CHIP 100K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) R4611 R3120 RES-CHIP RES-CHIP METAL CHIP RES-CHIP METAL CHIP 4.7K 2.2K 18 1K 18 5% 5% 0.5% 5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W METAL CHIP 18 0.5% 1/16W METAL CHIP 220K 0.5% 1/16W RES-CHIP 2.2K 5% 1/16W METAL CHIP 82 0.5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-208-663-11 METAL CHIP 150 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) R3121 R4137 R4201 R4203 R4214 1-218-977-11 1-218-965-11 1-218-953-11 1-218-982-11 1-218-959-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100K 10K 1K 270K 3.3K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R4215 R4219 R4221 R4222 R4223 1-218-953-11 1-218-953-11 1-208-911-11 1-218-965-11 1-218-953-11 RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 1K 1K 10K 10K 1K 5% 5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R4225 R4232 R4233 R4234 R4240 1-218-933-11 1-218-954-11 1-218-965-11 1-218-965-11 1-218-933-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 22 1.2K 10K 10K 22 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R4837 R4241 R4247 R4256 R4257 R4259 1-218-977-11 1-218-975-11 1-218-933-11 1-218-953-11 1-208-889-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 100K 68K 22 1K 1.2K 5% 5% 5% 5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W R4838 R4261 R4405 R4406 R4409 1-218-965-11 1-218-966-11 1-218-975-11 1-218-446-11 R4836 R4836 R4837 R4838 R4839 R4410 R4411 RES-CHIP 10K 5% 1/16W RES-CHIP 12K 5% 1/16W RES-CHIP 68K 5% 1/16W METAL CHIP 1 5% 1/10W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-446-11 METAL CHIP 1 5% 1/10W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-446-11 METAL CHIP 1 5% 1/10W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-22 R4840 180 100K 10K 10 10K 68K 10K 100K 68K 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1-208-943-11 METAL CHIP 220K 0.5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-208-910-11 METAL CHIP 9.1K 0.5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-208-711-11 METAL CHIP 15K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-208-715-11 METAL CHIP 22K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-208-934-11 METAL CHIP 91K 0.5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) R4911 R4913 R4915 R4917 R4929 1-219-570-11 1-208-893-11 1-208-703-11 1-218-953-11 1-218-985-11 METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 10M 1.8K 6.8K 1K 470K 5% 0.5% 0.5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R4930 R4932 R4933 1-218-989-11 RES-CHIP 1-218-977-11 RES-CHIP 1-208-927-11 METAL CHIP 1M 100K 47K 5% 5% 0.5% 1/16W 1/16W 1/16W VC-520 Ref. No. Part No. Description R4934 R4935 1-208-935-11 METAL CHIP 1-218-953-11 RES-CHIP R4937 R4942 R5135 R5136 1-218-965-11 1-218-965-11 1-218-969-11 1-218-968-11 R5136 R5137 R5138 R5139 R5140 R5301 Ref. No. 100K 1K 0.5% 5% 1/16W 1/16W R5320 RES-CHIP 10K 5% 1/16W RES-CHIP 10K 5% 1/16W RES-CHIP 22K 5% 1/16W RES-CHIP 18K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-969-11 RES-CHIP 22K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) R5321 R5322 R5402 R5403 1-218-965-11 1-218-953-11 1-218-947-11 1-218-969-11 RES-CHIP 10K 5% 1/16W RES-CHIP 1K 5% 1/16W RES-CHIP 330 5% 1/16W RES-CHIP 22K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-216-797-11 METAL CHIP 10 5% 1/10W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) R5404 R5405 R5406 R5409 R5410 R5302 R5303 R5304 R5305 R5306 R5307 R5310 R5311 R5312 R5314 R5315 R5316 R5317 R5318 R5319 1-218-941-81 RES-CHIP 100 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-977-11 RES-CHIP 100K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-965-11 RES-CHIP 10K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-977-11 RES-CHIP 100K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-961-11 RES-CHIP 4.7K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-971-11 RES-CHIP 33K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-980-11 RES-CHIP 180K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-972-11 RES-CHIP 39K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-980-11 RES-CHIP 180K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-962-11 RES-CHIP 5.6K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 1-218-980-11 RES-CHIP 180K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 1-218-980-11 RES-CHIP 180K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) R5411 R5412 R5414 R5415 Part No. Description 1-218-980-11 RES-CHIP 180K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 (DVD310E/DVD410E/ DVD710/DVD710E/DVD810/DVD810E) 1-218-965-11 RES-CHIP 10K 5% 1/16W (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) 1-218-989-11 RES-CHIP 1M 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-218-957-11 RES-CHIP 2.2K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-218-981-91 RES-CHIP 220K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-218-965-11 RES-CHIP 10K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) 1-218-967-11 RES-CHIP 15K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) 1-218-990-81 SHORT CHIP 0 (DVD110E/DVD115E/DVD610/DVD610E) 1-218-973-11 RES-CHIP 47K 5% 1/16W (DVD110E/DVD115E/DVD610/DVD610E) < COMPOSITION CIRCUIT BLOCK > * RB1001 RB1704 RB1705 RB1706 1-234-723-21 1-234-378-11 1-234-381-21 1-234-377-21 RES, NETWORK 75 (1005X4) RES, NETWORK 10K (1005X4) RES, NETWORK 100K (1005X4) RES, NETWORK 4.7K (1005X4) (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) * RB1707 1-234-384-21 RES, NETWORK 1M (1005X4) * RB1801 RB1802 RB1803 RB1804 RB1805 1-200-016-21 1-242-963-21 1-242-963-21 1-242-963-21 1-242-963-21 RB1806 RB1807 * RB2102 RB2801 1-234-378-11 1-234-943-21 1-234-380-21 1-234-376-11 RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK 82 (1005X4) 33 (1005X4) 33 (1005X4) 33 (1005X4) 33 (1005X4) RES, NETWORK 10K (1005X4) RES, NETWORK 22 (1005X4) RES, NETWORK 47K (1005X4) RES, NETWORK 2.2K (1005X4) (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) * RB2803 1-234-379-21 RES, NETWORK 22K (1005X4) (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) * RB2804 1-234-380-21 RES, NETWORK 47K (1005X4) (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) RB2805 1-234-945-21 RES, NETWORK 100 (1005X4) (DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) RB2901 1-234-378-11 RES, NETWORK 10K (1005X4) (DVD110E/DVD610/DVD610E) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-23 VC-520 Ref. No. Part No. Description Ref. No. RB2902 1-234-376-11 RES, NETWORK 2.2K (1005X4) (DVD110E/DVD610/DVD610E) RB2903 1-234-381-21 RES, NETWORK 100K (1005X4) (DVD110E/DVD610/DVD610E) RB2904 1-234-945-21 RES, NETWORK 100 (1005X4) (DVD110E/DVD610/DVD610E) 47K (1005X4) 100K (1005X4) 10K (1005X4) 22K (1005X4) * RB3102 RB3103 RB3104 * RB4101 1-234-380-21 1-234-381-21 1-234-378-11 1-234-379-21 RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK * RB4102 RB4301 RB4401 RB4403 RB4801 1-234-384-21 1-234-378-11 1-234-381-21 1-234-378-11 1-234-945-21 RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK 1M (1005X4) 10K (1005X4) 100K (1005X4) 10K (1005X4) 100 (1005X4) RB4901 RB4902 RB4903 RB4904 * RB4905 1-234-378-11 1-234-375-21 1-234-378-11 1-234-375-21 1-234-380-21 RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK RES, NETWORK 10K (1005X4) 1K (1005X4) 10K (1005X4) 1K (1005X4) 47K (1005X4) * RB5101 1-234-380-21 RES, NETWORK 47K (1005X4) RB5102 1-234-400-21 CONDUCTOR, NETWORK (1005X4) (DVD310E/DVD410E/DVD710/DVD710E/ DVD810/DVD810E) RB5103 1-234-400-21 CONDUCTOR, NETWORK (1005X4) (DVD110E/DVD115E/DVD610/DVD610E) RB5401 1-234-375-21 RES, NETWORK 1K (1005X4) (DVD110E/DVD115E/DVD610/DVD610E) RB5402 1-234-956-21 RES, NETWORK 470K (1005X4) (DVD110E/DVD115E/DVD610/DVD610E) < SENSOR > * SE4501 1-480-013-21 SHOCK SENSOR < VARISTOR > * * * * VD1001 VD1002 VD1005 VD1006 1-802-279-11 1-802-279-11 1-802-279-11 1-802-279-11 VARISTOR (SMD) VARISTOR (SMD) VARISTOR (SMD) VARISTOR (SMD) < VIBRATOR > * X1201 * X1201 X1201 * X1701 * X4201 * X4901 1-813-856-11 OSCILLATOR, CRYSTAL (27MHz) (DVD310E/DVD410E/DVD710E/DVD810E) 1-813-857-21 OSCILLATOR, CRYSTAL (33MHz) (DVD710/DVD810) 1-814-072-21 QUARTZ CRYSTAL OSCILLATOR (24MHz) (DVD110E/DVD115E/DVD610/DVD610E) 1-813-403-21 QUARTZ CRYSTAL OSCILLATOR (12MHz) 1-813-816-21 VIBRATOR, CERAMIC (33.8688MHz) 1-813-709-41 QUARTZCRYSTALUNITFOROSCILLATOR (32.768kHz) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 5-24 Part No. Description Reverse 985224912.pdf Revision History Ver. Date History 1.0 2007.12 Official Release 1.1 2008.01 Revised-1 (A1 DI07-258) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_L3 Contents — • Correction of Schematic Diagrams • Correction of Repair Parts S.M. correction: Page 4-9, Page 4-20, Page 5-20 S.M. Rev. issued — Yes DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E RMT-835 Ver. 1.2 2008.03 Revision History SECTION 6 ADJUSTMENTS Auto-ADJ Link Before starting adjustments DRIVE SECTION ADJUSTMENTS Adjusting items when replacing main parts and boards (Non MEGA model) Adjusting items when replacing main parts and boards (MEGA model) List of service tools PREPARATIONS BEFORE ADJUSTMENTS AUDIT (Drive Adjustment Program) DIAGNOSIS POWER ADJUSTMENT SERVO ADJUSTMENT CAMERA SECTION ADJUSTMENTS TROUBLESHOOTING PREPARATIONS BEFORE ADJUSTMENTS ADJUSTMENT PROGRAM DESTINATION DATA WRITE USB SERIAL No. INPUT VIDEO SYSTEM ADJUSTMENTS SERVICE MODE APPLICATION FOR ADJUSTMENT (SeusEX) SERVICE MODE DATA BACKUP CAMERA SYSTEM ADJUSTMENTS (Non MEGA model) CAMERA SYSTEM ADJUSTMENTS (MEGA model) LCD/EVF SYSTEM ADJUSTMENTS AUDIO SYSTEM ADJUSTMENTS ERROR • Use this Service Manual together with the Automatic Adjustment Program (DCR-DVD610 Series Auto-Adj Ver_1.2r03.exe or DCR-DVD710 Series Auto-Adj Ver_1.2r03.exe) and the AUDIT (Drive Adjustment Program). Non MEGA model: DCR-DVD110E/DVD115E/DVD610/DVD610E • Automatic Adjustment Program: DCR-DVD610 Series Auto-Adj Ver_1.2r03.exe MEGA model: DCR-DVD310E/DVD410E/DVD710/DVD710E/DVD810/DVD810E • Automatic Adjustment Program: DCR-DVD710 Series Auto-Adj Ver_1.2r03.exe DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 9-852-249-53 Sony EMCS Co. 2008C0500-1 © 2008.3 Published by Kohda TEC CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION: The use of optical instrument with this product will increase eye hazard. CAUTION Use of controls or adjustments or perfor mance procedures other than those specified herein may result in hazardous radiation exposure. CAUTION In the process of adjusting optical power, CLASS1M laser optical radiates. so do not remove this sensor disk. Optical sensor disc (J-6082-570-A) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ —2— 6. ADJUSTMENTS Before starting adjustments 1-1. Adjusting items when replacing main parts and boards (Non MEGA model) When replacing main parts and boards, adjust the items indicated by z in the following table. Note 1: The Automatic Adjustment Program does not support. Note 2: DCR-DVD115E only. Note 3: DCR-DVD110E/DVD610/DVD610E only. Note 4: IC2101 (Flash memory) on the VC-520 board and IC4302 (Flash memory) on the VC-520 board cannot be replaced. Replaced parts Destination Destination data write Data Write USB Serial No. USB serial No. input Input Origin oscillation check (Note 1) S VIDEO OUT Y level adj. VIDEO S VIDEO OUT chroma level adj. adjustment VIDEO OUT level check CAMERA HALL adj. adjustment 1 CAMERA Flange back adj. adjustment 2 CAMERA Flange back check adjustment 3 F No. standard data input CAMERA MAX GAIN adj. adjustment 4 Color reproduction adj. Color reproduction check CAMERA AWB & LV standard data input adjustment 5 AWB adj. AWB check CAMERA Black Defect adj. adjustment 6 LCD automatic adj. (VCO adj, Contrast adj.) LCD V-COM adj. adjustment Transmissive moed white balance adj. EVF automatic adj. (VCO adj, Contrast adj.) EVF White balance adj. adjustment Touch panel adjustment AUDIO adjustment AUDIT VC-520 board (COMPLETE) PD-351 board (COMPLETE) BL-021 board (COMPLETE) CD-731 board (COMPLETE) VC-520 board IC4401 (DVD mecha drive) VC-520 board IC4201 (DVD DSP) VC-520 board IC4101 (RF process) VC-520 board IC3101 (LCD/EVF driver) VC-520 board IC2901 (Video out, Audio I/O) (Note 3) VC-520 board IC2801 (Video out, Audio I/O) (Note 2) VC-520 board IC2401 (D/A converter) VC-520 board IC1201 (A/D converter, Timing generator) VC-520 board IC1701, X1701 (CPU, Oscillator) BL-021 board D5702 (EVF backlight) CD-731 board IC7101 (CCD imager ) Microphone unit MIC901 EVF block LCD902 (LCD panel) z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z Touch panel adj. Internal 3ch microphone sensitivity adj. (Note 2) POWER adj. SERVO adj. LCD block LCD901 (LCD panel) Drive block Adjustment Lens device Adjusting item Board replacement Parts replacement PD-351 board D6203 - 6205 (LCD backlight) Block replacement z z z z z z z z z z z z z z z z z z z z z Table 6-1-1 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-1 z z z 1-2. Adjusting items when replacing main parts and boards (MEGA model) When replacing main parts and boards, adjust the items indicated by z in the following table. Note 1: The Automatic Adjustment Program does not support. Note 2: When replacing the Flash Memory block, erase the data in internal memory of the board before replacement. Note 3: DCR-DVD410E/DVD810/DVD810E only. Note 4: CD-672 complete board is supplied instead of CD-687 complete board, because CD-672 complete board and CD-687 complete board are compatible. Note 5: IC2101 (Flash memory) on the VC-520 board and IC4302 (Flash memory) on the VC-520 board cannot be replaced. Replaced parts Destination Destination data write Data Write USB Serial No. USB serial No. input Input Origin oscillation check (Note 1) S VIDEO OUT Y level adj. VIDEO S VIDEO OUT chroma level adj. adjustment VIDEO OUT level check CAMERA HALL adj. adjustment 1 CAMERA Flange back adj. adjustment 2 CAMERA Flange back check adjustment 3 F No. standard data input CAMERA MAX GAIN adj. adjustment 4 Mechanical shutter adj Color reproduction adj. Color reproduction check CAMERA AWB & LV standard data input adjustment 5 AWB adj. AWB check CAMERA Black Defec adj. adjustment 6 CAMERA Steady shot check adjustment 7 LCD automatic adj. (VCO adj, Contrast adj.) V-COM adj. LCD adjustment Transmissive moed white balance adj. Reflective mode white balance adj. EVF automatic adj. (VCO adj, Contrast adj.) EVF White balance adj. adjustment Touch panel adjustment AUDIO adjustment AUDIT VC-520 board (COMPLETE) PD-352 board (COMPLETE) BL-022 board (COMPLETE) CD-672/687 board (COMPLETE) (Note 4) VC-520 board IC4401 (DVD mecha drive) VC-520 board IC4201 (DVD DSP) VC-520 board IC4101 (RF process) VC-520 board IC3101 (LCD/EVF driver) VC-520 board IC2801 (Video, Audio I/O) VC-520 board IC2401 (D/A converter) VC-520 board IC1201 (A/D converter, Timing generator) VC-520 board IC1701, X1701 (CPU, Oscillator) PD-352 board D6203 - 6205 (LCD backlight) BL-022 board D5701 (EVF backlight) CD-672/687 board SE7001, 7002 (YAW, PITCH sensor) (Note 4) Flash Memory block (Note 2, 3) Microphone unit MIC901 EVF block LCD902 (LCD panel) z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z Touch panel adj. z z z z z z z z z z z z Internal 3ch microphone sensitivity adj. POWER adj. SERVO adj. LCD block LCD901 (LCD panel) Drive block Adjustment Lens device Adjusting item Board replacement Parts replacement CD-672/687 board IC7002 (CCD imager ) (Note 4) Block replacement z z z z z z z z z z Table 6-1-2 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-2 z z Ver. 1.1 2008.01 1-3. List of service tools • Oscilloscope • Amplifier built-in speaker for PC • Color monitor • Adjustment sound source file J-1 • Frequency counter J-2 J-3 HASP key and application for adjustment (SeusEX) Personal computer (Note 1, 2) J-4 USB cable 1-829-868-31 Contact our service headquarters of each area how to get the application for adjustment (SeusEX) and HASP key. J-5 J-6 Flange back adjustment jig J-6082-563-A Minipattern box J-6082-353-B J-7 J-8 Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A J-9 Color bar chart Clear chart For PTB-450: J-6020-250-A For PTB-450: J-6080-621-A For PTB-1450: J-6082-559-A For PTB-1450: J-6082-560-A J-12 J-11 J-10 ND filter 1.0 J-6080-808-A ND filter 0.4 J-6080-806-A ND filter 0.1 J-6080-807-A Filter for color temperature correction (C14) J-6080-058-A J-13 J-14 Optical power meter J-6082-569-A Siemens star chart J-6080-875-A Camera table J-6082-384-A J-15 Optical sensor disc J-6082-570-A DVD–RW (DRW3) Reference + DOW Disc 8-212-001-51 Fig. 6-1-1 (1) Note 1: Personal computer OS: Windows 2000/XP (Camera Section) Windows 2000 SP4 or later/XP SP2 or later (Drive Section) RAM: 256MB or more recommended USB: 2.0 recommended (also compatible with 1.1) Three connectors are required. Note 2: The following programs and driver must already be installed in the personal computer. (Contact our service headquarters of each area how to get the programs and driver) • SeusEX • Optical power meter driver • AUDIT DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-3 J-16 J-17 DVD–R for Self Jitter Disc 8-212-002-11 J-18 DVD+RDL for Self Disc (Manufactured by Sony Corporation) J-19 AC adaptor AC-L200/L200B 1-479-285-21/41 (Note 3) Fig. 6-1-1 (2) Note 3: 1-479-285-21 (for except J model) 1-479-285-41 (for J model) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-4 Extension cable (10P) J-6082-572-A 6-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION) 1-1-1. Preparations 1) Connect the equipment for adjustments according to Fig. 6-1-3. L = 1 m (PTB-450) L = 40 cm (PTB-1450) Pattern box Front of the lens L Camera Fig. 6-1-2 Video system Adjustment Camera system Adjustment Oscilloscope Color monitor Terminated 75 Ω S-Video or Video Video Audio L Audio R To A/V jack PC (The SeusEX must be installed in the PC.) AC adaptor AC-L200/L200B (1-479-285-21/41) OS: Windows 2000/XP RAM: 256MB or more recommended USB: 2.0 recommended (also compatible with 1.1) Two connectors are required. AC IN To DC IN jack USB cable (1-829-868-31) HASP Key Fig. 6-1-3 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-5 1-1-2. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without inserting disc. 1. 2. 3. 4. 5. (HOME) menu – (SETTINGS) – MOVIE SETTINGS DIGITAL ZOOM ............................................................. STEADY SHOT ............................................................... AUTO SLW SHUTTR ..................................................... 6. (HOME) menu – (SETTINGS) – GENERAL SET DEMO MODE ................................................................. POWER switch ............................................................. Movie BACK LIGHT .................................................................. OFF NIGHTSHOT PLUS ........................................................ OFF (OPTION) menu FOCUS .......................................................................... AUTO OFF OFF OFF OFF 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame C C=D D Yellow Cyan Green White Magenta Red Blue Blue Yellow Cyan Green White Magenta Red H CRT picture frame V A B A=B B A Fig. b (monitor TV picture) Enlargement Fig. a (VIDEO terminal of A/V jack output waveform) Difference in level B Adjust the camera zoom and direction to obtain the output waveform shown in Fig. a and the monitor TV display shown in Fig. b. A Fig. 6-1-4 3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 6-1-4. (Color reproduction adjustment frame) 2) Clear chart (AWB adjustment frame) Shoot the color bar chart. Then adjust the zoom to TELE side from WIDE side, and stop it when the black frame of the chart disappears. Remove the color bar chart from pattern box and insert a clear chart in its place. 3) Chart for flange back adjustment Join together a piece of white A0 size paper (1189mm × 841 mm) and a piece of black paper to make the chart shown in Fig. 6-1-5. White 841 mm Black 1189 mm Note: Use a non-reflecting and non-glazing vellum paper. The size must be A0 or larger and the joint between the white and black paper must not have any undulations. Fig. 6-1-5 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-6 Ver. 1.2 2008.03 1-2. 3. Function of Each Button on Main Menu Screen When the Automatic Adjustment Program started, the Main Menu screen in Fig. 6-1-6 will appear. On this screen, select each adjustment section. ADJUSTMENT PROGRAM The DCR-DVD110E/DVD115E/DVD310E/DVD410E//DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E are adjusted by the Automatic Adjustment Program. The Automatic Adjustment Program enters automatically via the SeusEX the adjustment operations that were formerly entered manually by the adjustment remote commander (some items may be adjusted by manual operation on the operation screen of the SeusEX). 1. 1) 2) 3) 4) qd 1 Precautions When Using Automatic Adjustment Program The Automatic Adjustment Program writes the adjustment results such as EVR data to the set through two-way communication with the camcorder via the SeusEX. Accordingly, the Automatic Adjustment Program must be used in the environment where the SeusEX operates. The Automatic Adjustment Program cannot be used when the SEUS or the SeusCam is running. Exit the SEUS or the SeusCam before using the Automatic Adjustment Program. The SeusEX must be already started on the PC when using the Automatic Adjustment Program. With the SeusEX not started, some adjustment items will take time in adjustment. The program run time may vary depending on the environment of the personal computer used. qs 2 4 5 6 7 q; 8 qa 9 3 Fig. 6-1-6 1 [Connecting the Equipment] button A connection diagram of the equipment is displayed. 2. Start of Automatic Adjustment Program Double-click the application file (DCR-DVD610 Series Auto-Adj Ver_1.2r03.exe or DCR-DVD710 Series Auto-Adj Ver_1.2r03.exe), and the Automatic Adjustment Program will start. 2 [CONNECT] button The mode of Camcorder is switched to the Adjustment Mode. When the Adjustment Mode has switched normally, the operation of the buttons 4 - qa is enabled. 3 [END] button The mode of Camcorder is switched to the normal mode. When the normal mode has switched correctly, the Automatic Adjustment Program is finished. 4 [DESTINATION DATA WRITE] button The “DESTINATION DATA WRITE” screen appears. 5 [USB SERIAL No. INPUT] button The “USB SERIAL No. INPUT” screen appears. 6 [VIDEO SYSTEM ADJUSTMENT] button The “VIDEO SYSTEM ADJUSTMENT” screen appears. 7 [CAMERA SYSTEM ADJUSTMENT] button The “CAMERA SYSTEM ADJUSTMENT” screen appears. 8 [LCD/EVF SYSTEM ADJUSTMENT] button The “LCD/EVF SYSTEM ADJUSTMENT” screen appears. 9 [AUDIO SYSTEM ADJUSTMENT] button The “AUDIO SYSTEM ADJUSTMENT” screen appears. q; [SERVICE MODE] button The “SERVICE MODE” screen appears. qa [DATA BACKUP] button The “DATA BACKUP” screen appears. qs This part indicates the version of Automatic Adjustment Program. qd [Adjust item] button “Adjusting items when replacing main parts and boards” table is displayed. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-7 4. Setting of Adjustment Mode Before performing the adjustment, “Setting of Adjustment Mode” is required. 5. Release of Adjustment Mode To finish the adjustment, be sure to perform “Release of Adjustment Mode”. [Setting method] 1) Connect the Camcorder to the PC with a USB cable, and turn on the power switch. 2) The USB SELECT menu will appear on the LCD screen of the Camcorder, and then select “USB CONNECT (Memory Stick)” to establish the connection. 3) Start the Automatic Adjustment Program, and click the [Connect] button on the Main Menu screen. 4) When the following message is displayed, turn off and on again the power switch of the Camcorder. Note: Turning off and on the power switch causes the Camcorder to be switched to the Adjustment Mode. After the Camcorder restarted, click the [OK] button in the message window. [Releasing method] 1) Click the [END] button on the Main Menu screen. 2) When the following message is displayed, releasing of adjustment mode has completed. Click the [OK] button in the message window to exit the Automatic Adjustment Program. Note: The Camcorder switches to the normal mode by turning off and on the power switch. After the adjustment finished, turn off and on again the power switch of the Camcorder to confirm that the USB SELECT menu is displayed. 5) Upon successful completion of the settings in the Adjustment Mode, the operation of each button on the Main Menu screen is enabled. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-8 1-3. 2. Destination Data Write [Writing method] 1) Select the model name from the pulldown list. DESTINATION DATA WRITE Note: The DESTINATION DATA WRITE can be set with the Service board only. Performing the DESTINATION DATA WRITE with other than the Service board causes the error (E:20:00 will be blinking) and the power to be shut down. 1. Function of Each Button on Destination Data Write Screen Click the [DESTINATION DATA WRITE] button on the Main Menu screen, and the “DESTNATION DATA WRITE” screen in Fig. 6-1-7 will appear. 1 2) Select the target destination from the pulldown list. 4 5 2 3 Fig. 6-1-7 1 [To Menu] button Return to the main menu. 3) Click the [Data Write] button. 2 Model Name List Selects the model name. 3 Destination List Selects the written destination. 4 [Data Write] button Write the destination data to the camcorder. 4) Following message will be appeared after completing data writing. 5 Destination Check button Current destination setting checked when the “DESTINATION DATA WRITE” screen started is displayed. When this button is clicked, the destination is checked and the display is updated. 5) After the destination data writing completed, click the Destination Check button to check the destination. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-9 3. Selectable Language Table E HK AUS CH SV JE NE AEP UK Melayu Indonesia Hungarian Polish Czech a a a a a a a a a a Thai a a a a a a a a a a Turkish Korean a z z a z a a a a a a Simplified English a a a a a a a a a a a Traditional Chinese Greek Portuguese Simplified Chinese Dutch Russian Spanish German Italian French Japanese a a a z a a a a a a a Persian HK KR PL JE CND Espanyol E Canadian French AR2 BR1 E33 E23 HK1 KR2 PL1 JE3 CA2 E34 E35 E36 E37 HK1 AU2 CN1 CN2 SV1 JE3 CEL CEE CEI CEJ CEM CEP CEN CEH Braz.Portuguese J US MX AR BR English AREA J1 U2 MX2 Albanian PAL model NTSC model DESTINATION SELECTABLE LANGUAGE z z a a a a z z a z z z z z z z z z a a z z z z z z z z z z a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a z z a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a z: INITIAL LANGUAGE Table 6-1-3 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-10 a a a a a a a a a a a a a a a a a a a a a a a a a a z a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a 1-4. 1. Function of Each Button on USB Serial No. Input Screen Click the [USB SERIAL No. INPUT] button on the Main Menu screen, and the “USB SERIAL No. INPUT” screen in Fig. 6-1-8 will appear. USB SERIAL No. INPUT The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. If original ID can be read from the board before replacement, read it from the board before replacement using the “SERIAL READ/ WRITE” screen, and then write it after replacement. If original ID cannot be read from the board before replacement, write the ID for service using the “MANUAL WRITE” screen. (The ID for service is different from the ID written when the set is shipped.) Enter the PRODUCT ID (last 5 characters of model name) and SERIAL No. into the screen and write them. 1 3 2 4 5 6 7 Fig. 6-1-8 1 [To Menu] button Return to the main menu. 2 Display area The “PRODUCT ID”and “SERIAL No.” are displayed. 3 [Check Serial] button The USB SERIAL No. data is read from the camcorder and displayed in the display area. 4 [Read and Save] button The USB SERIAL No. data is read from the camcorder and saved in PC as a file. Default file name is as follows: (Example: MEGA model) DCR-DVD710_SERIAL_xxxxxxxx_yyyymmdd.dat Date USB serial number Data name 5 [Load and Write] button The USB SERIAL No. data is loaded from the file saved in PC and written to the camcorder. 6 Input area Enter “PRODUCT ID” and “SERIAL No.” when writing the ID for service. The “PRODUCT ID” is set from the last 5 characters of model name if the model name is selected. For the “SERIAL No.”, read it from the label on the camcorder body and enter it. 7 [Write Manually] button The USB SERIAL No. data entered in the input area is written to the camcorder. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-11 1-5. VIDEO SYSTEM ADJUSTMENTS 1. Function of Each Button on Video System Adjustment Screen Click the [VIDEO SYSTEM ADJUSTMENT] button on the Main Menu screen, and the “VIDEO SYSTEM ADJUSTMENT” screen in Fig. 6-1-9 will appear. 1 2 3 Fig. 6-1-9 1 [To Menu] button Return to the main menu. 2 [Preparation] button Notes for adjustment or jigs used are displayed. 3 [Start] button “Video Adjustment” starts. 2. Adjustment Items of VIDEO System Adjustment The adjustment items of video system adjustment are as listed in Table 6-1-4. The Automatic Adjustment Program executes the adjustment items if the VIDEO Adjustment Start button is clicked. Button Name (Note) VIDEO Adjustment Adjustment Measurement Point Measuring Instrument Origin Oscillation Check Pin 3 of X1701 on VC-520 board Frequency counter S VIDEO OUT Y Level Adj. Y signal terminal of S VIDEO plug of A/V jack (75 ohm terminated) S VIDEO OUT Chroma Level Adj. VIDEO OUT Level Check Adjusting Address Block Page Address - - Oscilloscope 10 60 4400 Chroma signal terminal of S VIDEO plug of A/V jack (75 ohm terminated) Oscilloscope 10 60 4401, 4402 VIDEO terminal of A/V jack (75 ohm terminated) Oscilloscope - - - Note: The Automatic Adjustment Program does not support. Table 6-1-4 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-12 - 3. Origin Oscillation Check Check the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent. Subject 4. VIDEO Adjustment [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Video Adj. 2. S VIDEO OUT Y Level Adj. 3. S VIDEO OUT Chroma Level Adj. 4. VIDEO OUT Level Check Not required Measurement Point Pin 3 of X1701 on VC-520 board Measuring Instrument Frequency counter Specified value f = 12000000 ± 240 Hz [Adjusting method] 1) Click the [Start] button of the VIDEO Adjustment. 2) The Automatic Adjustment Program executes the “1. Data Setting during Video Adj.”. 3) If “1. Data Setting during Video Adj.” completed successfully, the following screen is displayed during the execution of “2. S VIDEO OUT Y Level Adj.”. Using the [Up]/[Down] button on the screen, adjust so that the Y signal level satisfies the specified value. After the adjustment, click the [End] button in the screen. Switch setting 1) POWER ............................................................. MOVIE mode Checking method: 1) Check that the frequency (f) satisfies the specified value. 2 1 3 4 X1701 Measurement Point VC-520 BOARD (SIDE A) IC1701 Fig. 6-1-10 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-13 4) After that, the following screen is displayed during the execution of “3. S VIDEO OUT Chroma Level Adj.”. Using the [Up]/ [Down] button on the screen, adjust so that the Cr signal level and the Cb signal level satisfies the specified value. After the adjustment, check that the burst level of the chroma signals satisfies the specified value, and click the [End] button in the screen. 6) Upon successful completion of all item the VIDEO Adjustment, the following message is displayed. Click the [OK] button. 5) If the [End] button is clicked, “4. VIDEO OUT Level Check” will be executed. The following message and screen are displayed. Check that the sync signal level and burst level of the video signals satisfies the specified value, and click the [OK] button in the message. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-14 1-6. CAMERA SYSTEM ADJUSTMENTS (Non MEGA model) 1. Function of Each Button on Camera System Adjustment Screen Click the [CAMERA SYSTEM ADJUSTMENT] button on the Main Menu screen, and the “CAMERA SYSTEM ADJUSTMENT” screen in Fig. 6-1-11 will appear. 1 3 2 3 2 3 5 4 3 Fig. 6-1-11 1 [To Menu] button Return to the main menu. 2 [Preparation] button Notes for adjustment or jigs used are displayed. 3 [Start] button Each adjustment from “Camera Adjustment 1” to “Camera Adjustment 6” starts. 4 Model Select radio button Selects the model to be adjusted. Note: NTSC model: DCR-DVD610 PAL model: DCR-DVD110E/DVD115E/DVD610E 5 [Release Data Setting] button The data setting at the adjustment is cancelled. During the data setting, the button color changes from “white” to “red”. When the data setting is cancelled, the button color returns to “white”. (Use this button when an error occurred in the camera adjustment. If the adjustment completed successfully, the data setting is automatically cancelled and the button color returns to “white”.) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-15 2. Adjustment Items of Camera System Adjustment The adjustment items of camera system adjustment are as listed in Table 6-1-5. The Automatic Adjustment Program divides the adjustment items into six, camera adjustment 1-6. Clicking either CAMERA Adjustment Start button allows the adjustment item which corresponds to that button to be executed. The adjustment conditions of the subject and filter vary depending on which item is adjusted. The Adjustment Program displays an instruction for the subject and filter as a message during the adjustment. Adjustment Button Name CAMERA Adjustment 1 Subject HALL Adj. Not required CAMERA Adjustment 2 Flange Back Adj. Siemens star chart with ND filter for minipattern box (Note) or Flange back adjustment jig CAMERA Adjustment 3 Flange Back Check CAMERA Adjustment 4 F No. Standard Data Input MAX GAIN Adj. Color Reproduction Check Siemens star chart Clear chart (Center frame) Color bar chart (Color reproduction adjustment frame) 0020 to 0030, 004C, 004D 11 61 - - 11 61 0160 to 017F 11 61 015C to 015F 11 61 0060 to 006E - - Flange back adjustment chart and subject more than 500 m away Color Reproduction Adj. - - AWB & LV Standard Data Input Clear chart (All White frame) 11 61 0074 to 007B, 0180 to 018B, 01C0 to 01C3 AWB Adj. Clear chart (All White frame) Filter C14 for color temperature correction 11 61 0070 to 0073, 008C to 0093, 01C4 to 01C7 AWB Check Clear chart (All White frame) ND filter 1.0, 0.4 and 0.1 - - Black Defect Adj. Clear chart (All White) (Shoot the clear chart with the zoom TELE end.) 11 61 CAMERA Adjustment 5 CAMERA Adjustment 6 Adjusting Address Block Page Address 0150 to 0159, 11 61 0190 to 019B Note: Dark Siemens star chart. Table 6-1-5 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-16 - 00C0 to 011D, 01A0 to 01B3 3. CAMERA Adjustment 1 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. HALL Adj. 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 1. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) If “1. Data Setting during Camera Adj.” completed successfully, and the items “2. HALL Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 4) Upon successful completion of all items of the CAMERA Adjustment 1, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-17 Ver. 1.1 2008.01 4. CAMERA Adjustment 2 (Using the minipattern box or flange back adjustment jig) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back Adj. 3. Release of Data Setting during Camera Adj. [Preparation (Using the flange back adjustment jig)] (Illuminance: 950 to 1050 lux) Note 2: When using the flange back adjustment jig, take care of the following points: • For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering. • Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room illumination only. Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination. 1) Install the flange back adjustment jig so that the distance between it and the front of lens of camera is less than 3 cm. 2) Make the height of flange back adjustment jig and the camera equal. 3) Check that the center of chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. [Preparation (Using the minipattern box)] 1) The minipattern box is installed as shown in the following figure. Note 1: The attachment lenses are not used. 2) Install the minipattern box so that the distance between it and the front of lens of camera is less than 3 cm. 3) Make the height of minipattern box and the camera equal. 4) Check the output voltage of the regulated power supply is the specified voltage ± 0.01 Vdc. 5) Check that the center of Siemens star chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. Flange back adjustment jig Specified voltage: The specified voltage varies according to the minipattern box, so adjustment the power supply output voltage to the specified voltage written on the sheet which is supplied with the minipattern box. Below 3 cm Camera Below 3 cm Fig. 6-1-13 Minipattern box [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. Camera Regulated power supply Output voltage : Specified voltage ± 0.01 Vdc Output current : more than 3.5 A Red (+) Black (–) Yellow (SENS +) White (SENS –) 4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 5) Upon successful completion of all items of the CAMERA Adjustment 2, the following message is displayed. Click the [OK] button. Need not connected Black (GND) Fig. 6-1-12 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-18 Ver. 1.1 2008.01 5. CAMERA Adjustment 2 (Using the flange back adjustment chart and subject more than 500 m away) 5-1. CAMERA Adjustment 2 (1) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back (1) Adj. 3. Release of Data Setting during Camera Adj. 5-2. CAMERA Adjustment 2 (2) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back (2) Adj. 3. Release of Data Setting during Camera Adj. [Preparation] 1) Set the zoom lens to the TELE end and expose a subject that is more than 500 m away. (subjects with clear contrast such as building, etc.) (Nearby subjects less than 500 m away should not be in the screen) [Preparation] 1) Place the Flange back adjustment chart at 2 m position away from the lens. 2) Check that the center of Flange back adjustment chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. [Adjusting method] 1) Click the [Start $2%] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. [Adjusting method] 1) Click the [Start $1%] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. 4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be executed. The following message is displayed during the execution of adjustment, and then place the ND filter on the lens so as to obtain the optimum image. 4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 5) Upon successful completion of all items of the CAMERA Adjustment 2 (1), the following message is displayed. Click the [OK] button. 5) If “2. Flange Back Adj.” completed successfully, “3. Release of Data Setting during Camera Adj.” will be executed. 6) Upon successful completion of all items of the CAMERA Adjustment 2 (2), the following message is displayed. Click the [OK] button. 6) Perform “CAMERA Adjustment 2 (2)”. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-19 Ver. 1.1 2008.01 6. CAMERA Adjustment 3 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back Check 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 3. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject in accordance with the message. 4) If the [OK] button is clicked, “2. Flange Back Check” is executed. The following messages are displayed, and then operate the camera to make a check in accordance with the messages. 5) Upon completion of “2. Flange Back Check”, “3. Release of Data Setting during Camera Adj.” is executed. 6) Upon successful completion of all items of the CAMERA Adjustment 3, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-20 7. CAMERA Adjustment 4 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Picture Frame Setting (Center Frame) 3. F No. Standard Data Input 4. MAX GAIN Adj. 5. Release of Data Setting during Camera Adj. 8. CAMERA Adjustment 5 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Picture Frame Setting (Color Reproduction Adjustment Frame) 3. Color Reproduction Adj. 4. Color Reproduction Check 5. Picture Frame Setting (AWB Adjustment Frame) 6. AWB & LV Standard Data Input 7. AWB Adj. 8. AWB Check 9. Release of Data Setting during Camera Adj. [Adjusting method] 1) Select the model (NTSC Model or PAL Model) with the Model Select radio button. Note: NTSC model: DCR-DVD610 PAL model: DCR-DVD110E/DVD115E/DVD610E 2) Click the [Start] button of the CAMERA Adjustment 4. 3) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 4) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed during the execution of “2. Picture Frame Setting (Center Frame)”. Set the subject in accordance with the message. [Adjusting method] 1) Select the model (NTSC Model or PAL Model) with the Model Select radio button. Note: NTSC model: DCR-DVD610 PAL model: DCR-DVD110E/DVD115E/DVD610E 2) Click the [Start] button of the CAMERA Adjustment 5. 3) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 4) Upon successful completion of the “1. Data Setting during Camera Adj.”, “2. Picture Frame Setting (Color Reproduction Adjustment Frame)” is executed and the following message is displayed. Adjust the zoom and camera direction and then set the picture frame. After the setting finished, click the [End] button. 5) If the [OK] button is clicked, the following message is displayed, and then check the size of clear chart shot on the monitor screen. 6) After the checking, if the [OK] button in the message window is clicked, the adjustment items from “3. F No. Standard Data Input” to “4. MAX GAIN Adj.” are executed. 7) Upon successful completion of the “4. MAX GAIN Adj.”, “5. Release of Data Setting during Camera Adj.” is executed. 8) Upon successful completion of all items of the CAMERA Adjustment 4, the following message is displayed. Click the [OK] button. The buttons on this screen provide the following functions: [Save the position] button Saves the camera zoom and focus position data. [Load the position] button Reads the camera zoom and focus position data saved last and moves the camera zoom and focus to that position. Note 1: The zoom and focus position data are saved with “DCR_DVD610_ZoomFocusData.txt” file name in the same holder as the Automatic Adjustment Program. No position data can be read if this file is moved or deleted. Note 2: Only the latest position data can be saved. If the [Save the position] button is clicked, the latest data are saved overwriting the previous data. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-21 8) After the setting, if the [OK] button is clicked, the adjustment items from “6. AWB & LV Standard Data Input” to “8. AWB Check” are executed. During the execution, the following messages are displayed in the order given below. Place or remove the filters on the lens in accordance with the messages. 5) After setting the picture frame, if the [End] button is clicked, “3. Color Reproduction Adj.” and the adjustment items of “4. Color Reproduction Check” are executed. The following messages are displayed in the order given below during the excution. Then, change the chart in accordance with the messages. 6) Upon successful completion of the “7. Color Reproduction Check”, the following message is displayed. Then, set the picture frame in accordance with the message. 9) Upon completion of “8. AWB Check”, “9. Release of Data Setting during Camera Adj.” is executed 10) Upon successful completion of all items of the CAMERA Adjustment 5, the following message is displayed. Click the [OK] button. 7) If the [OK] button is clicked, “5. Picture Frame Setting (AWB Adjustment Frame)” is executed. The following messages are displayed in the order given below during the execution. Then, change the chart in accordance with the messages. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-22 9. CAMERA Adjustment 6 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Black Defect Adj. 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 6. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Then, set the subject in accordance with the message. 4) Click the [OK] button, and the “2. Black Defect Adj.” will be executed. 5) Upon completion of “2. Black Defect Adj.”, “3. Release of Data Setting during Camera Adj.” is executed. 6) Upon successful completion of all items of the CAMERA Adjustment 6, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-23 1-7. CAMERA SYSTEM ADJUSTMENTS (MEGA model) 1. Function of Each Button on Camera System Adjustment Screen Click the [CAMERA SYSTEM ADJUSTMENT] button on the Main Menu screen, and the “CAMERA SYSTEM ADJUSTMENT” screen in Fig. 6-1-14 will appear. 1 3 2 3 2 4 3 4 5 3 Fig. 6-1-14 1 [To Menu] button Return to the main menu. 2 [Preparation] button Notes for adjustment or jigs used are displayed. 3 [Start] button Each adjustment from “Camera Adjustment 1” to “Camera Adjustment 7” starts. 4 Model Select radio button Selects the model to be adjusted. Note: NTSC model: DCR-DVD710/DVD810 PAL model: DCR-DVD310E/DVD410E/DVD710E/ DVD810E 5 [Release Data Setting] button The data setting at the adjustment is cancelled. During the data setting, the button color changes from “white” to “red”. When the data setting is cancelled, the button color returns to “white”. (Use this button when an error occurred in the camera adjustment. If the adjustment completed successfully, the data setting is automatically cancelled and the button color returns to “white”.) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-24 2. Adjustment Items of Camera System Adjustment The adjustment items of camera system adjustment are as listed in Table 6-1-6. The Automatic Adjustment Program divides the adjustment items into seven, camera adjustment 1-7. Clicking either CAMERA Adjustment Start button allows the adjustment item which corresponds to that button to be executed. The adjustment conditions of the subject and filter vary depending on which item is adjusted. The Adjustment Program displays an instruction for the subject and filter as a message during the adjustment. Adjustment Button Name CAMERA Adjustment 1 Subject HALL Adj. Not required CAMERA Adjustment 2 Flange Back Adj. Siemens star chart with ND filter for minipattern box (Note) or Flange back adjustment jig CAMERA Adjustment 3 Flange Back Check Siemens star chart MAX GAIN Adj. Clear chart (Center frame) Mechanical Shutter Adj. Color Reproduction Adj. Color Reproduction Check Color bar chart (Color reproduction adjustment frame) 0020 to 0030, 004C, 004D 11 61 - - 11 61 0160 to 017F 11 61 015C to 015F 11 61 0120 to 0136 11 61 0060 to 006E - - Flange back adjustment chart and subject more than 500 m away F No. Standard Data Input CAMERA Adjustment 4 Adjusting Address Page Address 0150 to 0159, 11 61 0190 to 019B Block - - AWB & LV Standard Data Input Clear chart (All White frame) 11 61 0074 to 007B, 0180 to 018B, 01C0 to 01C3 AWB Adj. Clear chart (All White frame) Filter C14 for color temperature correction 11 61 0070 to 0073, 008C to 0093, 01C4 to 01C7 AWB Check Clear chart (All White frame) ND filter 1.0, 0.4 and 0.1 - - CAMERA Adjustment 6 Black Defect Adj. Clear chart (All White) (Shoot the clear chart with the zoom TELE end.) 11 61 CAMERA Adjustment 7 Steady shot Check Not required - - CAMERA Adjustment 5 Note: Dark Siemens star chart. Table 6-1-6 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-25 - 00C0 to 011D, 01A0 to 01B3 - 3. CAMERA Adjustment 1 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. HALL Adj. 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 1. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) If “1. Data Setting during Camera Adj.” completed successfully, and the items “2. HALL Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 4) Upon successful completion of all items of the CAMERA Adjustment 1, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-26 Ver. 1.1 2008.01 4. CAMERA Adjustment 2 (Using the minipattern box or flange back adjustment jig) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back Adj. 3. Release of Data Setting during Camera Adj. [Preparation (Using the flange back adjustment jig)] (Illuminance: 950 to 1050 lux) Note 2: When using the flange back adjustment jig, take care of the following points: • For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering. • Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room illumination only. Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination. 1) Install the flange back adjustment jig so that the distance between it and the front of lens of camera is less than 3 cm. 2) Make the height of flange back adjustment jig and the camera equal. 3) Check that the center of chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. [Preparation (Using the minipattern box)] 1) The minipattern box is installed as shown in the following figure. Note 1: The attachment lenses are not used. 2) Install the minipattern box so that the distance between it and the front of lens of camera is less than 3 cm. 3) Make the height of minipattern box and the camera equal. 4) Check the output voltage of the regulated power supply is the specified voltage ± 0.01 Vdc. 5) Check that the center of Siemens star chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. Flange back adjustment jig Specified voltage: The specified voltage varies according to the minipattern box, so adjustment the power supply output voltage to the specified voltage written on the sheet which is supplied with the minipattern box. Below 3 cm Camera Below 3 cm Fig. 6-1-16 Minipattern box [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. Camera Regulated power supply Output voltage : Specified voltage ± 0.01 Vdc Output current : more than 3.5 A Red (+) Black (–) Yellow (SENS +) White (SENS –) 4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 5) Upon successful completion of all items of the CAMERA Adjustment 2, the following message is displayed. Click the [OK] button. Need not connected Black (GND) Fig. 6-1-15 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-27 Ver. 1.1 2008.01 5. CAMERA Adjustment 2 (Using the flange back adjustment chart and subject more than 500 m away) 5-1. CAMERA Adjustment 2 (1) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back (1) Adj. 3. Release of Data Setting during Camera Adj. 5-2. CAMERA Adjustment 2 (2) [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back (2) Adj. 3. Release of Data Setting during Camera Adj. [Preparation] 1) Set the zoom lens to the TELE end and expose a subject that is more than 500 m away. (subjects with clear contrast such as building, etc.) (Nearby subjects less than 500 m away should not be in the screen) [Preparation] 1) Place the Flange back adjustment chart at 2 m position away from the lens. 2) Check that the center of Flange back adjustment chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. [Adjusting method] 1) Click the [Start $2%] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. [Adjusting method] 1) Click the [Start $1%] button of the CAMERA Adjustment 2. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject by referring to “Preparation”. 4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be executed. The following message is displayed during the execution of adjustment, and then place the ND filter on the lens so as to obtain the optimum image. 4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3. Release of Data Setting during Camera Adj.” will be executed. 5) Upon successful completion of all items of the CAMERA Adjustment 2 (1), the following message is displayed. Click the [OK] button. 5) If “2. Flange Back Adj.” completed successfully, “3. Release of Data Setting during Camera Adj.” will be executed. 6) Upon successful completion of all items of the CAMERA Adjustment 2 (2), the following message is displayed. Click the [OK] button. 6) Perform “CAMERA Adjustment 2 (2)”. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-28 Ver. 1.1 2008.01 6. CAMERA Adjustment 3 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Flange Back Check 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 3. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Set the subject in accordance with the message. 4) If the [OK] button is clicked, “2. Flange Back Check” is executed. The following messages are displayed, and then operate the camera to make a check in accordance with the messages. 5) Upon completion of “2. Flange Back Check”, “3. Release of Data Setting during Camera Adj.” is executed. 6) Upon successful completion of all items of the CAMERA Adjustment 3, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-29 7. CAMERA Adjustment 4 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Picture Frame Setting (Center Frame) 3. F No. Standard Data Input 4. MAX GAIN Adj. 5. Mechanical Shutter Adj. 6. Release of Data Setting during Camera Adj. 8) Upon successful completion of all items of the CAMERA Adjustment 4, the following message is displayed. Click the [OK] button. [Adjusting method] 1) Select the model (NTSC Model or PAL Model) with the Model Select radio button. Note: NTSC model: DCR-DVD710/DVD810 PAL model: DCR-DVD310E/DVD410E/DVD710E/ DVD810E 2) Click the [Start] button of the CAMERA Adjustment 4. 3) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 4) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed during the execution of “2. Picture Frame Setting (Center Frame)”. Set the subject in accordance with the message. 5) If the [OK] button is clicked, the following message is displayed, and then check the size of clear chart shot on the monitor screen. 6) After the checking, if the [OK] button in the message window is clicked, the adjustment items from “3. F No. Standard Data Input” to “5. Mechanical Shutter Adj.” are executed. 7) Upon successful completion of the “5. Mechanical Shutter Adj.”, “6. Release of Data Setting during Camera Adj.” is executed. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-30 Note 2: Only the latest position data can be saved. If the [Save the position] button is clicked, the latest data are saved overwriting the previous data. 5) After setting the picture frame, if the [End] button is clicked, “3. Color Reproduction Adj.” and the adjustment items of “4. Color Reproduction Check” are executed. The following messages are displayed in the order given below during the excution. Then, change the chart in accordance with the messages. 8. CAMERA Adjustment 5 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Picture Frame Setting (Color Reproduction Adjustment Frame) 3. Color Reproduction Adj. 4. Color Reproduction Check 5. Picture Frame Setting (AWB Adjustment Frame) 6. AWB & LV Standard Data Input 7. AWB Adj. 8. AWB Check 9. Release of Data Setting during Camera Adj. [Adjusting method] 1) Select the model (NTSC Model or PAL Model) with the Model Select radio button. Note: NTSC model: DCR-DVD710/DVD810 PAL model: DCR-DVD310E/DVD410E/DVD710E/ DVD810E 2) Click the [Start] button of the CAMERA Adjustment 5. 3) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 4) Upon successful completion of the “1. Data Setting during Camera Adj.”, “2. Picture Frame Setting (Color Reproduction Adjustment Frame)” is executed and the following message is displayed. Adjust the zoom and camera direction and then set the picture frame. After the setting finished, click the [End] button. 6) Upon successful completion of the “4. Color Reproduction Check”, the following message is displayed. Then, set the picture frame in accordance with the message. 7) If the [OK] button is clicked, “5. Picture Frame Setting (AWB Adjustment Frame)” is executed. The following messages are displayed in the order given below during the execution. Then, change the chart in accordance with the messages. The buttons on this screen provide the following functions: [Save the position] button Saves the camera zoom and focus position data. [Load the position] button Reads the camera zoom and focus position data saved last and moves the camera zoom and focus to that position. Note 1: The zoom and focus position data are saved with “DCR_DVD710_ZoomFocusData.txt” file name in the same holder as the Automatic Adjustment Program. No position data can be read if this file is moved or deleted. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-31 8) After the setting, if the [OK] button is clicked, the adjustment items from “6. AWB Standard Data Input” to “8. AWB Check” are executed. During the execution, the following messages are displayed in the order given below. Place or remove the filters on the lens in accordance with the messages. 9) Upon completion of “8. AWB Check”, “9. Release of Data Setting during Camera Adj.” is executed 10) Upon successful completion of all items of the CAMERA Adjustment 5, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-32 9. CAMERA Adjustment 6 10. CAMERA Adjustment 7 [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Steady Shot Check 3. Release of Data Setting during Camera Adj. [Automatic Adjustment Program execution items and sequence] 1. Data Setting during Camera Adj. 2. Black Defect Adj. 3. Release of Data Setting during Camera Adj. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 7. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. With the camcoder in stationary state, click the [OK] button. [Adjusting method] 1) Click the [Start] button of the CAMERA Adjustment 6. 2) The Automatic Adjustment Program executes “1. Data Setting during Camera Adj.”. 3) Upon successful completion of the “1. Data Setting during Camera Adj.”, the following message is displayed. Then, set the subject in accordance with the message. 4) If the [OK] button is clicked, “2. Steady Shot Check” is executed. Upon successful completion of the “2. Steady Shot Check”, the following message is displayed. Check that the steadyshot function operates normally in accordance with the message. 4) Click the [OK] button, and the “2. Black Defect Adj.” will be executed. 5) Upon completion of “2. Black Defect Adj.”, “3. Release of Data Setting during Camera Adj.” is executed. 6) Upon successful completion of all items of the CAMERA Adjustment 6, the following message is displayed. Click the [OK] button. 5) If the [OK] button is clicked, “3. Release of Data Setting during Camera Adj.” is executed. 6) Upon successful completion of all items of the CAMERA Adjustment 7, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-33 1-8. 1 [To Menu] button Return to the main menu. LCD/EVF SYSTEM ADJUSTMENTS 1. Function of Each Button on LCD/EVF System Adjustment Screen Click the [LCD/EVF SYSTEM ADJUSTMENT] button on the Main Menu screen, and the “LCD/EVF SYSTEM ADJUSTMENT” screen in Fig. 6-1-17 will appear. 1 2 [Start] button Each adjustment “LCD Adjustment”, “EVF Adjustment” or “Touch Panel Adjustment” starts. 2 Fig. 6-1-17 2. Adjustment Items of LCD/EVF System Adjustment The adjustment items of LCD/EVF system adjustment are as listed in Table 6-1-7. The Automatic Adjustment Program executes the adjustment items if the LCD/EVF Adjustment Start button is clicked. Button Name LCD Adjustment EVF Adjustment Touch Panel Adjustment Adjustment Block Adjusting Address Page Address 1050 (NTSC model), 60 1051 (PAL model) VCO Adj. 10 Contrast Adj. 10 60 1058 V-COM Adj. 10 60 1052 Transmissive Mode White Balance Adj. 10 60 1056, 1057 Reflective Mode White Balance Adj. 10 60 107B, 107C VCO Adj. 10 60 103F (NTSC model), 1040 (PAL model) Contrast Adj. 10 60 1047 White Balance Adj. 10 60 1045, 1046 Touch Panel Adj. (Note) Note: The adjustment data cannot be read or written from the SeusEX. Table 6-1-7 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-34 4) If the [End] button is clicked, the following screen is displayed during the execution of “4. Transmissive Mode White Balance Adj.”. Check that the LCD screen is not colored. If colored, using the [Up]/[Down] button on the screen, adjust so that the LCD screen is not colored. After the adjustment, click the [End] button in the screen. 3. LCD Adjustment [Automatic Adjustment Program execution items and sequence] 1. Data Setting during LCD/EVF Adj. 2. LCD Automatic Adj. (VCO Adj., Contrast Adj.) 3. V-COM Adj. 4. Transmissive Mode White Balance Adj. 5. Reflective Mode White Balance Adj. [Adjusting method] 1) Click the [Start] button of the LCD Adjustment. 2) The Automatic Adjustment Program executes the “1. Data Setting during LCD/EVF Adj.” and “2. LCD Automatic Adj.”. 3) After that, the following screen is displayed during the execution of “3. V-COM Adj.”. Using the [Up]/[Down] button on the screen, adjust so that the brightness of portions A and B on the LCD panel is equal. After the adjustment, click the [End] button in the screen. 5) If the [End] button is clicked, “5. Reflective Mode White Balance Adj.” will be executed. 6) Upon successful completion of all item the LCD Adjustment, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-35 4. EVF Adjustment [Automatic Adjustment Program execution items and sequence] 1. Data Setting during LCD/EVF Adj. 2. EVF Automatic Adj. (VCO Adj., Contrast Adj.) 3. White Balance Adj. 5. Touch Panel Adjustment [Automatic Adjustment Program execution items and sequence] 1. Touch Panel Adj. [Adjusting method] 1) Click the [Start] button of the Touch Panel Adjustment. 2) The Automatic Adjustment Program executes the “1. Touch Panel Adj.1”. The following message is displayed, and then adjust the LCD screen in accordance with the instructions given on the screen. After the adjustment, click the [OK] button in the message window. [Adjusting method] 1) Click the [Start] button of the EVF Adjustment. 2) The Automatic Adjustment Program executes the “1. Data Setting during LCD/EVF Adj.” and “2. EVF Automatic Adj.”. 3) After that, the following screen is displayed during the execution of “3. White Balance Adj.”. Check that the EVF screen is not colored. If colored, using the [Up]/[Down] button on the screen, adjust so that the EVF screen is not colored. After the adjustment, click the [End] button in the screen. 4) Upon successful completion of all item the EVF Adjustment, the following message is displayed. Click the [OK] button. 3) Upon successful completion of all item the Touch Panel Adjustment, the following message is displayed. Click the [OK] button. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-36 1-9. AUDIO SYSTEM ADJUSTMENTS (DCR-DVD115E/DVD310E/DVD410E/DVD710/ DVD710E/DVD810/DVD810E) 1. Function of Each Button on Audio System Adjustment Screen Click the [AUDIO SYSTEM ADJUSTMENT] button on the Main Menu screen, and the “AUDIO SYSTEM ADJUSTMENT” screen in Fig. 6-1-18 will appear. 1 2 3 4 Fig. 6-1-18 1 [To Menu] button Return to the main menu. 2 [Preparation] button Notes for adjustment or jigs used are displayed. 3 [Start] button “Audio Adjustment” starts. 4 [Release Data Setting] button The data setting at the adjustment is cancelled. During the data setting, the button color changes from “white” to “red”. When the data setting is cancelled, the button color returns to “white”. (Use this button when an error occurred in the audio adjustment. If the adjustment completed successfully, the data setting is automatically cancelled and the button color returns to “white”.) 2. Adjustment Items of AUDIO System Adjustment The adjustment items of audio system adjustment are as listed in Table 6-1-8. The Automatic Adjustment Program executes the adjustment items when the AUDIO Adjustment Start button is clicked. Button Name AUDIO Adjustment Adjustment Adjusting Address Block Page Address Internal 3ch Microphone Sensitivity Adj. 10 Table 6-1-8 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-37 60 0104 to 013F 3. AUDIO Adjustment Note 1: Perform “AUDIO Adjustment” without inserting disc. Note 2: AUDIO Adjustment is available only once after the power is turned on. If the adjustment is retried, turn off the power and turn on again. [Adjusting method] 1) Play back the adjustment sound source file on the PC. 2) Set the speaker volume so that the adjustment signal sound is heard to the extent of the loudness of talking voices. 3) Click the [Start] button of the AUDIO Adjustment. 4) The Automatic Adjustment Program executes “1. Data Setting during Audio Adj.”. 5) When “1. Data Setting during Audio Adj.” completed successfully, and the items “2. Internal 3ch microphone Adj.” and “3. Release of Data Setting during Audio Adj.” will be executed. 6) Upon successful completion of all items of the AUDIO Adjustment, the following message is displayed. Click the [OK] button. [Automatic Adjustment Program execution items and sequence] 1. Data Setting during AUDIO Adj. 2. Internal 3ch microphone Adj. 3. Release of Data Setting during Audio Adj. [Preparation] Prepare an amplifier built-in speaker for PC and arrange it above the internal 3ch microphone of the camcoder. • Adjust the speaker position so that it is within ±3 cm from the center of camcoder internal 3ch microphone at the height of 40 cm. • The diaphragm of speaker position should be set face down toward the internal 3ch microphone. • The speaker may be held by hand if it is hard to secure. In case of adjustment NG, reduce or increase the speaker volume, and then retry adjustment. If the Adjustment Program displays a message “Volume too loud” or “Volume too low”, adjust the speaker volume following the message. PC Amplifier built-in speaker for PC about 40 cm Internal 3ch microphone Fig. 6-1-19 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-38 3. 1-10. ERROR Adjustment Time Out In the case of an error during the execution of adjustment, the Automatic Adjustment Program interrupts the processing at that point, and displays an error message, and then terminates the program execution there. This part indicates the adjustment item in which an error occurred. 1-10-1. Error Message When an error message is displayed, perform the remedy given below, and then retry adjustment. If the error message is displayed though the remedy was performed, the circuits will be faulty. 1. Fig. 6-1-22 Connect Error, Adjust Control Error Fig. 6-1-20 Symptom USB communication with the set is abnormal. Cause • USB cable is not inserted tightly. • Power supply is not installed correctly. • Communication with SeusEX is abnormal. Remedy • Disconnect the USB cable once, and then reconnect it tightly and check that the set is in “USB Mode”. • Install the power supply correctly. • Start the SeusEX and click the [Connect] to check that the connection state is established. 2. Cause Data error exists in the camera. Remedy Reset the camera. Cause • Adjustment conditions are wrong. • Data error exists in the camera. Remedy • Check that the conditions such as a subject are correct. • Reset the camera. Adjustment NG This part indicates the adjustment item in which an error occurred. Fig. 6-1-23 Fig. 6-1-21 The camera is not ready for adjustment. Adjustment does not finish within the specified time. 4. RESET the CAMERA and Try Again Symptom Symptom DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-39 Symptom The adjusted data does not become the specified value. Cause • Adjustment conditions are wrong. • Data error exists in the camera. Remedy • Check that the conditions such as a subject are correct. • Reset the camera. 1-10-2. Precautions When an Error Occurred The Automatic Adjustment Program sets the data for adjustment before the adjustment starts. Accordingly, if the adjustment terminates by an error, the data during the adjustment may be left in the camera. Note: With this data left in the camera, the camera will not operate normally. Audio System Adjustment screen In this case, the [Release Data Setting] button is displayed in “red” on the screen as shown figures below. Click the [Release Data Setting] button to cancel the data setting. When the data setting is cancelled, the button color becomes “white”. Fig. 6-1-25 Camera System Adjustment screen Fig. 6-1-24 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-40 Ver. 1.1 2008.01 6-2. DRIVE SECTION ADJUSTMENTS 2-1. PREPARATIONS BEFORE ADJUSTMENTS (DRIVE SECTION) 2-1-1. Connection 1) Connect the apparatuses as shown below, and perform adjustment. Note 1: Before starting the adjustment, remove the disc from the camcorder. PC (The SeusEX must be installed in the PC.) OS: Windows 2000 SP4 or later/XP SP2 or later RAM: 256MB or more recommended USB: 2.0 recommended (also compatible with 1.1) Three connectors are required. AC adaptor AC-L200/L200B (1-479-285-21/41) AC IN To DC IN jack USB cable (1-829-868-31) To DRIVE (Note 2) HASP Key Optical sensor disc (J-6082-570-A) Optical power meter (J-6082-569-A) POWER Adjustment Note 2: Refer to “How to Set the Optical Sensor Disc”. Fig. 6-2-1 [Connecting method] 1) Connect the Camcorder to the PC with a USB cable, and turn on the power switch. 2) The USB SELECT menu will appear on the LCD screen of the Camcorder, and then select “USB CONNECT (Memory Stick) ” to establish the connection. Note 3: Don’t select “USB CONNECT (Disc) ”. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-41 2-1-2. How to Set Optical Sensor Disc 1) Before setting the optical sensor disc, remove a lug on the sensor side of the disc. 2-1-3. Precautions on Adjustment 1. Adjustment data The adjustment data for the drive block are recorded to the IC4302 on the VC-520 board. These data cannot be read or written from the adjustment remote commander or SeusCam, unlike the camera and LCD adjustment data. Accordingly, be sure to adjust all items of the drive adjustment when the following parts were replaced: • Drive block • Mounted VC-520 board • IC4101 (RF process) on the VC-520 board • IC4201 (DVD DSP) on the VC-520 board • IC4401 (DVD mecha drive) on the VC-520 board Remove this lug Fig. 6-2-2 2) Push in the optical sensor disc until it clicks same as when a disc is set, and adjust the position so that the cable from the sensor comes just above the pickup lens, as shown below. After positioning, fix the disc with a tape so that it does not rotate. 2. Order of adjustment Adjust the drive block in the following order: 1) POWER Adjustment 2) SERVO Adjustment This part should come just above the pickup 3. Precaution on the laser diode In the POWER Adjustment, operate the drive with the disc cover left open. During the adjustment, be sure to observe the following precautions: 1) Set the optical sensor disc correctly. 2) Keep the distance of more than 30 cm apart from the camcoder. 3) Work on the LCD screen side of the camcoder (opposite side of the drive). Note: Laser light of the equipment is focused by the object lens in the optical pick-up so that the light focuses on the reflection surface of the disc. Therefore, be sure to keep your eyes more then 30 cm apart from the object lens when you check the emission of laser diode. Fix with a tape Fig. 6-2-3 Pickup Lens (Laser Diode) Fig. 6-2-4 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-42 2-1-4. Alignment disc To diagnose and adjust the drive block, the discs listed in the following table are used. Note 1: Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT) If a wrong disc is used, the disc could be destroyed and could not be reused. Note 2: Handle the disc with care, and before use, check if the disc is scratched or dirty. Name Use Remark DVD-R Disc for Self Jitter Diagnosis and adjustment of DVD-R This disc can be used about 78 times (min. 22 times) for the diagnosis and adjustment. (Note 3) DVD-RW Reference + DOW Disc Diagnosis and adjustment of DVD-RW This disc can be used about 1174 times for the diagnosis and adjustment. (Note 3) DVD+RDL Self Disc Diagnosis and adjustment of DVD+RDL This disc can be used about 38 times (min. 9 times) for the diagnosis and adjustment. (Note 3) Table 6-2-1 Note 3: If the use counts of the DVD-R Disc for Self Jitter, DVD-RW Reference + DOW Disc, or DVD+RDL Disc for Self Jitter exceed respective limits, the following message will be displayed. Replace it with a new disc and click the [OK] button in the message window. The disc use counts are saved in the PC. Accordingly, the disc used for diagnosis and adjustment, PC and drive adjustment program (AUDIT for 2008) must always be controlled in the same combination. If the disc is used with another PC or other versions (AUDIT for Service, AUDIT for UX1, etc.), the diagnosis and adjustment will fail and that disc will no longer be able to use. For reference (Note 3 in Japanese) 注3:DVD-R セルフジッターディスク,DVD-RWリファレンス+ DOWディスクとDVD+RDLセルフジッターディスクは,使 用限度を超えると次のメッセージが表示されます。新しいディスクと交換して,メッセージの[OK]ボタンをクリックし てください。 ディスクの使用回数は,PC内部に保存されます。このため,診断・調整で使用するディスクとPCおよびドライブ調整 プログラム(AUDIT for 2008)の組み合わせには制限があります。(2-1-5.Unigue disc IDを参照) 別のPCや他のバージョン(AUDIT for Service,AUDIT for UX1等)でディスクを使用すると,診断・調整が正常に行わ れずNGとなってしまい,そのディスクが使用不可能になってしまう場合があります。 Fig. 6-2-5 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-43 2-1-5. Unique disc ID (For all kind, DVD-RW, DVD-R, DVD+RDL) Unique disc ID will be written on the disc which is used first time for AUDIT for 2008. At the same time, same disc ID will be stored in the install folder of AUDIT for 2008. AUDIT is checking whether these ID is same or not. Thus, the PC and the adj disc must be managed together. In fact, adjustment discs can not be swapped between the PC which AUDIT for 2008 is installed each other. The disk which ID is not storeed is considered as new disc (not recorded at all). When you use the disc used halfway, it might be possible cause of some error. 1. Disc shareing between the previous AUDIT and AUDIT for 2008 Start using disc first time is AUDIT for 2008 Start using disc first time is previous AUDIT OK AUDIT for 2008 previous AUDIT OK previous AUDIT AUDIT for 2008 DVD-RW AUDIT for 2008 previous AUDIT OK Able to share AUDIT for 2008 OK Able to share OK previous AUDIT previous AUDIT AUDIT for 2008 DVD-R AUDIT for 2008 previous AUDIT It is able to use on previous AUDIT but it is unable to use on AUDIT for 2008 again. Due to address mismatch of file management. AUDIT for 2008 OK Unable to share (AUDIT 2008 detect the disc as new one due to missing disc ID.) previous AUDIT previous AUDIT AUDIT for 2008 DVD+RDL AUDIT for 2008 previous AUDIT It is able to use on previous AUDIT but it is unable to use on AUDIT for 2008 again. Due to address mismatch of file management. 2. Unable to share AUDIT 2008 detect the disc as new one due to missing disc ID. Disc shareing between the PC which is installed AUDIT for 2008 PC1 PC2 AUDIT for 2008 AUDIT for 2008 All discs Unable to share (Each PC has deferent disc information) DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-44 Ver. 1.1 2008.01 2-1-6. Installation method for “Audit for 2008” Support environment: Windows 2000 SP4 or later, Windows XP SP2 or later (.NET Framework which used in this program may not be installed on previous version of Windows.) “Audit for 2008” supports all functions of “Audit for 2007”. It is not necessary to use “Audit for 2007” any more. Disc set for adjustment which used on “Audit for 2007” can be used on “Audit for 2008” if they aren't used on other PCs before installing “Audit for 2008”. 1) Uninstall “Audit for 2007”. Control Panel → Add or Remove Programs 2) Uninstall “Audit for 2008” (If it is already installed). Control Panel → Add or Remove Programs 3) Install .NET Framework 2.0 (only for the first time installation). Download “dotnetfx.exe” as suitable for your PC environment from Microsoft Web site and install it. (We confirmed normal operation just on .NET Framework 2.0. Therefore, we can not guarantee on the other version (over ver. 3.0) of .NET Framework.) 4) Install “Audit for 2008”. Double click Auditfor2008.exe and follow installer. Note: If it is first time to install .NET Framework 2.0, we recommend to check the security patch by Windows Update, etc. and to install if necessary. Perform just step 2 and 4 from second installation. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-45 Ver. 1.1 2008.01 2-2. AUDIT (Drive Adjustment Program) 2-2-1. AUDIT Starting Method Click the [Start] button on the task bar, and from the [Programs], click [AUDIT for Service] – [AUDIT for 2008], and the AUDIT will start. The SeusEX starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment. Again, the SeusEX starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the AUDIT operation screen appears. If the SeusEX cannot start (because, for instance, the HASP key is not connected to the PC), the AUDIT also does not start. 2-2-2. Description of Screen 1. Diagnosis section 2. Adjustment section 5. [STOP] button 6. [SET] button 7. Menu section 8. Caution display section 3. Comment display section Fig. 6-2-6 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-46 4. Status display section 6. [SET] button (After completing the TEST) This button cancels the TEST mode set to the cam coder during the diagnosis and adjustment. If the TEST mode is cancelled successfully, the following message is displayed. Note: Before exiting the AUDIT, be sure to cancel the TEST mode by clicking the SET button of “After completing the TEST”. Unless the TEST mode is cancelled, the drive may not operate normally, such that “disc cover does not open”, “drive error is displayed”, etc.. 1. Diagnosis section Use these buttons when diagnosing the drive block. 2. Adjustment section Use these buttons when adjusting the drive block. 3. Comment display section At the execution of diagnosis and adjustment, its progress situation is displayed. 1) [Clear] button This button clears the comment in the display section. 2) [LOG] button This button saves the comment in the display section as a log file. [Clear] button [LOG] button Fig. 6-2-9 7. Menu section 1) [RESET] button This button resets internal register. (Use this button to interrupt the work so far when diagnosis and adjustment stopped and no response is returned. The work terminates with the previous adjustment data written to the camcoder.) 2) [Lid Open] button This button opens the disc cover. Fig. 6-2-7 4. Status display section The result of diagnosis and adjustment is displayed. 8. Caution display section At the execution of POWER Adjustment, the caution of POWER Adjustment is displayed. Fig. 6-2-10 Fig. 6-2-8 5. [STOP] button This button stops the diagnosis and adjustment in the midway. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-47 2-3. DIAGNOSIS 2-3-1. Menu in Diagnosis Section START button: START button Status lamp All items of diagnosis buttons are executed in the descending order. Diagnosis button: Only the diagnostic item assigned to the button name is executed. Status lamp: Diagnosis status is displayed with color. White Not diagnosed Red blinking Diagnosis in progress Green Diagnosis OK Red Diagnosis NG Diagnosis buttons Fig. 6-2-11 2-3-2. Order 1 Diagnosing Method Diagnostic item Disc No Disc No Disc 2 3 Message Sensors 4 No Disc No Disc DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-48 Operation Click the [START] button of “DIAGNOSIS”. Check the movement of the pickup lens (Focus direction/Tracking direction), and click the [OK] button in the message window. Check the movement of the sled, and click the [OK] button in the message window. Check the rotation of the spindle, and click the [OK] button in the message window. Order Diagnostic item Message Disc No Disc 5 Operation Set the Optical sensor disc. (At this time, when the Shock Sensor senses a shock normally, this message disappears. Sensors Set the Optical sensor disc, and with the disc Optical Sensor Disc cover left open, click the [OK] button in the message window. (Note 1) 6 7 -R Seek DVD-R Disc for Self Jitter 8 -R Read 9 -R Write 10 (If the diagnosis result of previous item is OK, this item is executed successively.) (If the diagnosis result of previous item is OK, this item is executed successively.) -RW Seek DVD-RW Reference + DOW Disc 11 -RW Read 12 -RW Write Set the DVD-R Disc for Self Jitter, and then close the disc cover and click the [OK] button in the message window. Remove the DVD-R Disc for Self Jitter, and set the DVD-RW Reference + DOW Disc, and then close the disc cover and click the [OK] button in the message window. (If the diagnosis result of previous item is OK, this item is executed successively.) (If the diagnosis result of previous item is OK, this item is executed successively.) Note 1: In the process of checking optical power, CLASS 1M laser optical radiates. So do not remove the Optical sensor disc. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-49 Order 13 Diagnostic item Message Disc +RDL Seek DVD+RDL Self Disc 14 +RDL Read 15 +RDL Write 16 Operation Remove the DVD-RW Reference + DOW Disc, and set the DVD+RDL Self Disc, and then close the disc cover and click the [OK] button in the message window. (If the diagnosis result of previous item is OK, this item is executed successively.) (If the diagnosis result of previous item is OK, this item is executed successively.) No Disc Remove the DVD+RDL Self Disc. (On the AUDIT screen, if the status lamps of respective diagnosis buttons are all lit in green, the diagnosis is over.) Note 2: Before exiting the AUDIT, click the [SET] button of “After completing the TEST” to cancel the TEST mode. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-50 2-4. POWER ADJUSTMENT In the POWER Adjustment, operate the drive with the disc cover left open. During the adjustment, be sure to observe the following precautions: 1) Set the optical sensor disc correctly. 2) Keep the distance of more than 30 cm apart from the camcoder. 3) Work on the LCD screen side of the camcoder (opposite side of the drive). 2-4-1. Menu in POWER Adjustment Section START button: START button Adjustment buttons Status lamp All items of adjustment buttons are executed in the descending order. Adjustment button: Only the adjustment item assigned to the button name is executed. Status lamp: Adjustment status is displayed with color. White Not adjusted Red blinking Adjustment in progress Green Adjustment OK Red Adjustment NG Fig. 6-2-12 2-4-2. Order Adjusting Method Adjustment item Message Disc 1 No Disc 2 No Disc Operation Click the [START] button of “POWER Adjustment”. Set the Optical sensor disc. (At this time, when the Shock Sensor senses a shock normally, this message disappears. Initial & Sensor Set the Optical sensor disc, and with the disc cover left open, click the [OK] button in the Optical Sensor Disc message window. (Note 1) 3 4 Power Adjust 5 No Disc (If the adjustment result of previous item is OK, this item is executed successively.) Remove the Optical Sensor Disc. (On the AUDIT screen, if the status lamps of respective adjustment buttons are all lit in green, the adjustment is over.) Note 1: In the process of adjusting optical power, CLASS 1M laser optical radiates. So do not remove the Optical sensor disc. Note 2: Before exiting the AUDIT, click the [SET] button of “After completing the TEST” to cancel the TEST mode. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-51 2-5. 2-5-1. SERVO ADJUSTMENT Menu in SERVO Adjustment Section START button: START button Status lamp Adjustment buttons Fig. 6-2-13 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-52 All items of adjustment buttons are executed in the descending order. Adjustment button: Only the adjustment item assigned to the button name is executed. Status lamp: Adjustment status is displayed with color. White Not adjusted Red blinking Adjustment in progress Green Adjustment OK Red Adjustment NG 2-5-2. Order Adjusting Method Adjustment item Servo Param Initialize 3 -RW Ref 4 -RW Self 5 Disc No Disc 1 2 Message -R Self 6 +RDL Self 7 Data Dump 8 DVD-RW Reference + DOW Disc Operation Click the [START] button of “SERVO Adjustment”. Set the DVD-RW Reference + DOW Disc, and with the disc cover left open, click the [OK] button in the message window. (If the adjustment result of previous item is OK, this item is executed successively.) (If the adjustment result of previous item is OK, this item is executed successively.) DVD-R Disc for Self Jitter DVD+RDL Self Disc Remove the DVD-RW Reference + DOW Disc, and set the DVD-R Disc for Self Jitter, and then close the disc cover and click the [OK] button in the message window. Remove the DVD-R Disc for Self Jitter, and set the DVD+RDL Self Disc, and then close the disc cover and click the [OK] button in the message window. (If the adjustment result of previous item is OK, this item is executed successively.) No Disc Remove the DVD+RDL Self Disc. (On the AUDIT screen, if the status lamps of respective adjustment buttons are all lit in green, the adjustment is over.) Note: Before exiting the AUDIT, click the [SET] button of “After completing the TEST” to cancel the TEST mode. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-53 2-6. 2-6-1. TROUBLESHOOTING Fundamental Troubleshooting Flow Initial inspection Execute Yes OK? End No Execute Yes OK? No Faulty part isolation processing Faulty part isolation processing Replace MD Block Execute No VC Board recovery processing OK? Yes (MD Block is faulty) Return to initial inspection DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-54 VC Board recovery processing Replace RF IC Replace DSP IC Replace Driver IC Priority varies depending on the isolated item Execute No OK? Yes Restore original MD Block Execute No OK? Replace MD Block Yes End DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-55 2-6-2. Diagnosis Sensor Purpose Check operation of OP (Focus, Tracking, Sled, Spindle) Trouble Symptom Check the emission of laser diode Check various sensors (Dew sensor, Temperature sensor, Shock sensor) Cause Faulty OP Faulty Driver IC Repair Replace the MD block Replace the VC board Faulty connection of flexible board Faulty OP Faulty sensor, Faulty connection of flexible board Check flexible board OP age-based change Faulty operation of mechanism Faulty DSP IC Faulty RF IC Disc type check (only DVD-R) Replace the MD block Temperature sensor t Replace the MD block Dew sensor t Check flexible board Shock sensor t Replace the VC board Replace the MD block Replace the MD block Replace the VC board Replace the VC board The following diagnosis is performed with DVD-R, DVD-RW and DVD+DLR The diagnosis of DVD+RDL is performed with L0/L1 layer each layer. Seek Purpose Check the seek performance (Seek between 2 points) x5 x2 patterns t Calculation of average time Trouble Symptom Cause OP age-based change Faulty mechanism Faulty DSP IC Faulty RF IC Repair Readjust Replace the MD block Replace the VC board Replace the VC board Trouble Symptom Cause OP age-based change Faulty mechanism Faulty DSP IC Faulty RF IC Repair Readjust Replace the MD block Replace the VC board Replace the VC board Trouble Symptom Cause OP age-based change Faulty mechanism Faulty DSP IC Faulty RF IC Repair Readjust Replace the MD block Replace the VC board Replace the VC board Read Purpose Check the read performance LPP Error Rate, RF Jitter Write Purpose Check the write performance During LPP/ADIP Error Rate, RF Jitter DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-56 2-6-3. Power Adjust Prepare, Sensor Purpose Initialization of all data at adjustment area Check operation of Shock sensor Laser Power Adjustment Purpose Adjust the Laser power Trouble Symptom Trouble Symptom Cause Faulty Flash IC Repair Replace the VC board Faulty shock sensor Replace the VC board Cause Faulty connection to power meter Faulty installation of power sensor jig Faulty lighting of LD Repair Check connection to power meter, Check power supply Check installation of power sensor jig Check flexible board, Replace the MD block Replace the MD block Faulty operation of mechanism Faulty RF IC Faulty DSP IC Faulty SDRAM IC Faulty Flash IC DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-57 Replace the VC board Replace the VC board Replace the VC board Replace the VC board 2-6-4. Servo Adjust Servo Parameter Initialize Purpose Initialization of servo-related adjustment data Trouble Symptom DVD-RW Reference Disc Adjustment Purpose Trouble Symptom Adjust the servo with DVD-RW DVD-RW Self Jitter Purpose Adjust the recording with DVD-RW Check the self recording with DVD-RW DVD-R Self Jitter Purpose Adjust the servo with DVD-R Adjust the recording with DVD-R Check the self recording with DVD-R DVD+RDL Self Jitter Purpose Adjust the servo with DVD+RDL Adjust the recording with DVD+RDL Check the self recording with DVD+RDL Data Dump Purpose The adjustment value is dumped Trouble Symptom Trouble Symptom Trouble Symptom Trouble Symptom Cause Faulty Flash IC Faulty DSP IC Cause The disc is dirty or has scratches on it Faulty OP Faulty DSP IC Faulty RF IC Cause The disc is dirty or has scratches on it Faulty OP Faulty DSP IC Faulty RF IC Cause The disc is dirty or has scratches on it Faulty OP Faulty DSP IC Faulty RF IC Cause The disc is dirty or has scratches on it Faulty OP Faulty DSP IC Faulty RF IC Cause Faulty DSP IC Faulty RF IC DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-58 Repair Replace the VC board Replace the VC board Repair Check disc Replace the MD block Replace the VC board Replace the VC board Repair Check disc Replace the MD block Replace the VC board Replace the VC board Repair Check disc Replace the MD block Replace the VC board Replace the VC board Repair Check disc Replace the MD block Replace the VC board Replace the VC board Repair Replace the VC board Replace the VC board 6-3. SERVICE MODE 3-1. APPLICATION FOR ADJUSTMENT (SeusEX) The adjustment software (SeusEX) can change operational coefficients of signal processing, EVR data, etc. same as the adjustment remote commander. The SeusEX performs two-way communication between PC and camcorder using the USB terminal. The twoway communication result data can be written in the nonvolatile memory. 1. 1) 2) 3) 4) 2. Operation • Block change To change the block, click [Block] on the SeusEX screen and enter the block to be changed. The block is displayed in hexadecimal notation. • Page change To change the page, click [Page] on the SeusEX screen and enter the page to be changed. The page is displayed in hexadecimal notation. Connection Connect the HASP key to the USB terminal of the PC. Connect the PC and camcorder with the USB cable. Start the SeusEX on the PC. Click [Connect] on the SeusEX screen. If the connection is normal, the SeusEX screen will be as shown in Fig. 6-3-1, indicating the “connected” state. Note: The SeusEX will go in “disconnect” state, if the camcorder is turned off (for instance, by resetting the set). In such a case, click [Connect] on the SeusEX screen to restore the “connected” state. • Address change To change the address, click [Address] on the SeusEX screen and enter the address to be changed. The address is displayed in hexadecimal notation. • Data change To change the data, click [Set] on the SeusEX screen and enter the data. The data is displayed in hexadecimal notation. This operation does not write the data to the nonvolatile memory. • Data writing To write the data to the EEPROM, click [Write] on the SeusEX screen and enter the data value to be written. To write the data to the flash memory, change the data value using the [Set] on the SeusEX screen and then click [Save] to save the data. • Data reading The data displayed on the SeusEX screen are the data values at the time when the pages and addresses were set, and they are not updated automatically. To check the data change, click [Read] on the SeusEX screen and update the displayed data. Fig. 6-3-1 DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-59 3-2. 2. Switch Check Click the [Switch Check] button on the SERVICE MODE screen, and the “SWITCH CHECK” screen will appear. SERVICE MODE 1. Function of Each Button on Service Mode Screen Click the [SERVICE MODE] button on the Main Menu screen, and the “SERVICE MODE” screen in Fig. 6-3-2 will appear. 1 2 3 4 Fig. 6-3-2 1 [To Menu] button Return to the main menu. Using method: Click the [Start] button, and the switch check will start. During execution of switch check, the pressed switch is displayed in orange. Also, once the switch was pressed, its name characters change to blue in color. 2 [Switch Check] button “SWITCH CHECK” screen appears. 3 [LED Check] button “LED CHECK” screen appears. 4 [Jack Check] button “JACK CHECK” screen appears. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-60 3. LED Check Click the [LED Check] button on the SERVICE MODE screen, and the “LED CHECK” screen will appear. 4. Jack Check Click the [Jack Check] button on the SERVICE MODE screen, and the “JACK CHECK” screen will appear. Using method: LED ON or OFF can be controlled with [LED ON] or [LED OFF] button on the screen. Using method: Click the [Start] button, and the jack check will start. During execution of jack check, the connected jack is displayed in orange. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-61 3-3. DATA BACKUP With the “DATA BACKUP”, the adjustment data in the camcorder can be backed up in the PC as a file. The adjustment data that can be backed up are as follows. 1) 2) 3) 4) 1. Function of Each Button on Data Backup Screen Click the [DATA BACKUP] button on the Main Menu screen, and the “DATA BACKUP” screen in Fig. 6-3-3 will appear. 1 Video System Adjustments Camera System Adjustments LCD/EVF System Adjustments Audio System Adjustments 2 Note: The adjustment data for the drive cannot be backed up. 3 Fig. 6-3-3 1 [To Menu] button Return to the main menu. 2 [Data Read and Save] button Read the adjustment data from the camcorder and save them in PC as a file. Default file name is as follows: (Example: MEGA model) DCR-DVD710_MEM_xxxxxxxx_yyyymmdd.dat Date USB serial number Data name 3 [Data Load and Write] button Load the adjustment data from the file saved in PC and write them to the camcorder. DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ 6-62E Reverse 985224953.pdf Revision History History Date 1.0 2007.12 Official Release — 1.1 2008.01 Revised-1 (A1 DI07-262) Replace the previously issued SERVICE MANUAL 9-852-249-51 with this Manual. • Change of Automatic Adjustment Program Version of Automatic Adjustment Program has been changed from Ver_1.0r01 into Ver_1.1r02. • Correction of adjustment condition. • Change of System requirements for using AUDIT. • Addition of Installation method for “Audit for 2008”. • Deletion of Installation Method. S.M. revised: Page 6-3, Page 6-7, Page 6-18, Page 6-19, Page 6-20, Page 6-27, Page 6-28, Page 6-29, Page 6-41, Page 6-45, Page 6-46 Yes 1.2 2008.03 Revised-2 (A2 DI07-300) Replace the previously issued SERVICE MANUAL 9-852-249-52 with this Manual. • Change of Automatic Adjustment Program Version of Automatic Adjustment Program has been changed from Ver_1.1r02 into Ver_1.2r03. S.M. revised: Page 6-7 Yes DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/ DVD610E/DVD710/DVD710E/DVD810/DVD810E_ADJ Contents S.M. Rev. issued — Ver.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2009:04:21 11:16:56+02:00 Create Date : 2009:04:21 11:16:56+02:00 Metadata Date : 2009:04:21 11:16:56+02:00 Creator Tool : Adobe PageMaker 6.53 Format : application/pdf Title : DCR-DVD110E/DVD115E/DVD310E/DVD410E/DVD610/DVD610E/DVD710/DVD710E/DVD810/DVD810E Description : US,Canadian,AEP,UK,East European,North European,E,Australian,Hong Kong,Chinese,Korea,Argentine,Brazilian,Tourist,Japanese Creator : Sony Corporation Document ID : uuid:72901824-4544-4a11-b18c-d252f3d968b4 Instance ID : uuid:b5ef7b17-1125-49e2-a439-968fbf2b88c2 Producer : Acrobat Distiller 5.0.5 for Macintosh Has XFA : No Page Count : 195 Subject : US,Canadian,AEP,UK,East European,North European,E,Australian,Hong Kong,Chinese,Korea,Argentine,Brazilian,Tourist,Japanese Author : Sony CorporationEXIF Metadata provided by EXIF.tools