DRTS 6 _GB DATA SHEET

ISA-DRTS-6-Data-Sheet-Brochure ISA-DRTS-6-Data-Sheet-Brochure

User Manual: DRTS-6-DATA-SHEET

Open the PDF directly: View PDF .
Page Count: 11

Download
Open PDF In Browser	View PDF

DRTS 6
Advanced Relays, Energy Meters and Transducers Test Set

•

Multi-tasking test set designed for testing
protection relays, energy meters, transducers.

•
•

Powerful and lightweight.

•
•
•
•
•

High accuracy: better than 0.1% (standard);
HP model better than 0,05%.
IEC61850 Protocol interface.
Up to 9 current and 6 voltage outputs plus
auxiliary DC supply (option).
Laptop PC or PDA control.
USB and RS232 interfaces.
Advanced testing and data management
software TDMS.

•

Complete library of relays from the major
manufacturers.

•
•

Highest quality, safety and reliability.
Worldwide high quality technical support in
100 countries.

A

P

P

L

I

C

A

T

I

O

N

DRTS 6 can test all the following relays

RELAY TYPE
Distance relay
Synchronizing device
Under/over-voltage relay
Directional Power relay
Field relay
Reverse phase current relay
Phase sequence voltage relay
Incomplete sequence relay
Instantaneous over-current relay
Inverse time over-current relay
Power factor relay
Voltage balance relay
Ground detector relay
Directional over-current relay
Phase angle out of step relay
Automatic reclosing relay
Frequency relay
Pilot wire receiver relay
Lockout relay
Differential protection relay
Voltage directional relay
Power directional relay
Tripping relay

IEEE NO
21
25
27/59
32
40
46
47
48
50
51
55
60
64
67
78
79
81
85
86
87
91
92
94

DRTS 6

DRTS 6 SPECIFICATIONS
Six phase AC/DC current outputs
AC/DC current outputs

6X
6X
6X
3X
3X
3X
3X
3X
3X
3X
2X
1X
1X

CURRENT
A

POWER
VA

ZMAX
Ohm

0...15
0...1.5
0...0.15
0...15
0...1.5
0...0.15
0...30
0...3
0...0.3
0...15
0...45
0...90
0...30

80

0.35
0.35
0.35
0.44
0.44
0.44
0.18
0.18
0.18
0.71
0.12
0.06
0.35

100

160

160
240
480
320

RESOLUTION

1
0.1
0.1
1
0.1
0.1
2
0.2
0.2
1
3
6
2

mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA

. Six independent current sources with a common neutral.
. Independent adjustment of current outputs.
. Duty cycle: at 20°C ambient temperature: 3*15 A continuous;
6*7.5 A continuous; 6*15 A 3 minutes.
. Waveform resolution: 28 bit.
. Capable of stepping or ramping the current.
. Rate of change programmable between ± 0.001 A/s and ±
999 A/s.
. Output accuracy: ± 0.05% typical, ± 0.1% guaranteed.
. Distortion: 0.1%.
. Automatic protection for overloads and open circuit.

Four phase AC/DC voltage outputs
AC/DC voltage outputs
VOLTAGE
POWER
V
VA
4X
3X
3X
3X
1X
1X

0...300
0...300
0...125
0...12.5
0...600
0...300

85
100
100
10
200
200

ZMAX
Ohm
1125
900
160
160
1800
450

RESOLUTION
4.6
4.6
1.9
190
9.2
4.6

mV
mV
mV
µV
mV
mV

. Four independent voltage sources, with a common neutral.
. Independent adjustment of voltage outputs.
. Duty cycle: continuous.

2

. Waveform resolution: 28 bit.
. Capable of stepping or ramping the voltage.
. Rate of change programmable between ± 0.001 V/s and
± 999 V/s.
. Voltage accuracy: ± 0.05% typical, ± 0.1% guaranteed.
. Distortion: 0.1%.
. Automatic protection for overloads, counter-feed and short
circuit.
. The fourth voltage output can be selected to act as:
.. Fourth voltage output V4 (AC/DC);
.. Zero-sequence component
VO = (V1+V2+V3)/3 or VO = (V1+V2 +V3)/1.73.

Battery simulator
Output voltage: 0…260 V DC, program controlled.
Power: 100 W or 2 A; continuous duty.
Accuracy: ± 1%.
Automatic protection for overloads.
Step or ramp control.

Angles
Phase angle range: 0° - 360°.
Angle resolution: 0.01°.
Angle accuracy: ± 0.1°.
Step or ramp control with a rate of change between
± 0.1°/s and 999°/s.

Output frequency
Frequency range: from DC (0 Hz) to 2000 Hz. Transient 5 kHz.
Capable of generating different frequencies on any output.
Maximum frequency error: 25 µHz (0.5 ppm).
Resolution: 0.1 mHz.
Possibility of slewing the frequency, with a slope from 0.001
Hz/s to 999.999 Hz/s. Resolution: 0.001 Hz/s.
Capable of generating waveform with superimposed harmonic
distortion.

Binary inputs
10 binary inputs clean or with voltage from 24 to 425 V AC
and 4.5 to 600 V DC, separated in two groups of 5, with two
common points isolated at 1 kV AC.
Selection of the type of input: Voltage clean; 5 - 24 - 48 - 100
V; software controlled.
Selection of the input debounce duration, from 0 us to
2 ms, in 64 steps of 32 us each, program controlled.
Timer range: 0 - 999,999.9999 s (277 hours) or, in cycles:

DRTS 6

RELAYS, ENERGY METERS AND TRANSDUCERS TEST SET

0 - 50,000,000 cycles (50 Hz);
0 - 60,000,000 cycles (60 Hz).
Resolution: 0.1 ms.
Timer accuracy: 0.025% of reading ± 0.1 ms.

AC/DC Voltage measuring Input, High
Measuring range ± 250 V.
AC accuracy: 0.1% of range ± 0.1% of value.
DC accuracy: 0.05% of range ± 0.05% of value.

Counter inputs

Interface connection

These inputs allow testing energy meters, including high
frequency outputs.
Number of inputs: 2; with no common zero point.
Frequency range: 0 to 50 kHz.

Type of interface: USB and RS232 at 57.6 kbaud.

Auxiliary outputs
Four timed relay contacts; both normal open and normal closed
provided.
Characteristics of contacts with a resistive load:
. Maximum voltage: 300 V AC/DC;
. Maximum current: 8 A.
Range of programmable delay: from 0 to 999.99 s.

Power supply
Mains power supply: 90 to 132 and 180 to 264 V AC, sinusoidal,
single phase.
Frequency: 47 to 63 Hz.
Power consumption:
. standby: less than 150 W;
. maximum load: 1600 W.

Case
Aluminum, with carrying handle.

Low level signal outputs

Weight and dimensions

The purpose of these low voltage outputs is to test protection
relays that use transducers such as Rogowsky coils and voltage
dividers; for this simulation low voltage inputs are necessary.
Number of outputs: 6.
Full range V & I output: 0... 7.26 V rms.
Frequency: DC to 20 kHz.
Output current: 5 mA max.
Resolution: 0.43 mV or 0.043 mV.
Accuracy: 0.1% of the range.
Distortion: 0.1% typical.

Weight: 18 kg.
Dimensions: 170 (h) x 470 (w) x 430 (d) mm.

Accessories supplied with the unit
Protective carrying bag.
Set of test leads.
Power supply cable.
Serial interface cable and USB cable.
Ground connection cable.
Instruction and maintenance manuals.
TDMS software.

Analog Measurements (optional):
DC Current measuring Input, Low
Measuring range: ± 20 mA.
Accuracy: 0.02% of range ± 0.01% of value.
DC Voltage measuring Input, Low
Measuring range ± 10 V.
Accuracy: 0.02% of range ± 0.01% of value.
AC/DC Current measuring Input, High
Measuring range: ± 20 A.
AC accuracy: 0.2% of range ± 0.1% of value.
DC accuracy: 0.1% of range ± 0.1% of value.

DRTS 6 HP
High Precision option
This option has enhanced characteristics with respect to
the standard model. This model is conceived for the test of
class 0.2 energy meters. The following table summarizes the
performances of the DRTS 6 HP (High Precision) version with
respect to the standard one.

3

DRTS 6

STANDARD DRTS 6 ACCURACY
OUTPUT CURRENT
Typical: ± 0.05% ± 0.01% of range
Maximum: ± 0.1% ± 0.02% of range
OUTPUT VOLTAGE
Typical: ± 0.05% ± 0.01% of range
Maximum: ± 0.1% ± 0.02% of range
PHASE ANGLE
Typical: ± 0.02°
Maximum: ± 0.1°
3 PHASE POWER
Typical: ± 0.05%
Maximum: ± 0.2%

DRTS 6 HP ACCURACY
OUTPUT CURRENT
Typical: ± 0.02% from 0.1 to 15 A
Maximum: ± 0.05% from 0.1 to 15 A
OUTPUT VOLTAGE
Typical: ± 0.02% from 50 to 300 V
Maximum: ± 0.05% from 50 to 300 V
PHASE ANGLE
Typical: ± 0.01°
Maximum: ± 0.02°
3 PHASE POWER
Typical: ± 0.05%
Maximum: ± 0.1%

ADDITIONAL EXTERNAL AMPLIFIERS
FOR DRTS 6
AMI 99
Three phase current amplifier
The three phase current amplifier AMI 99 is an additional
device to the DRTS 6. DRTS 6 in connection with AMI 99
allows to have 9 currents or 6 currents at 30 A per phase or
three currents at 60 A per phase.

AMI 99 with DRTS 6
CURRENT
A
9X
9X
9X
6X
6X
6X
3X
3X
3X
1X

6 x 0...15
3 x 0...30
6 x 0...1.5
3 x 0...3
6 x 0...0.15
3 x 0...0.3
0...30
0...3
0...0.3
0...60
0...6
0...0.6
0...180

POWER
VA

ZMAX
Ohm

80
160

0.35
0.18

160

0.18
0.18
0.18
0.09
0.09
0.09
0.029

320

960

RESOLUTION
230
460
23
46
2.3
4.6
460
46
4.6
920
92
9.2
2.8

AMI 99 stand alone

3X
3X
3X
1X
1X

CURRENT
A
0...30
0...3
0...0.3
0...30
0...90

POWER
VA
160

320
480

ZMAX
Ohm
0.18
0.18
0.18
0.35
0.06

RESOLUTION
460 µA
46 µA
4.6 µA
460 µA
1.38mA

AMI 99 stand alone
. Three independent current sources, with a common neutral.
. Automatic range switch and independent range selection.
. Waveform resolution: 28 bit.
. Output accuracy: ± 0.1% of the output, ± 0.02% of the range.
. Distortion: 0.1% total maximum, with any load.
. Automatic protection for overloads.
. Angle accuracy: ± 0.05°.

Power supply
Mains power supply: 90 to 264 V AC, single phase.
Frequency: 47 to 63 Hz.
Power consumption:
. stanby: less than 100 W;
. maximum load: 1000 W.

Weight and dimensions
Weight: 16 kg.
Dimensions: 170 (h) x 470 (w) x 430 (d) mm.
4

µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
mA

DRTS 6

RELAYS, ENERGY METERS AND TRANSDUCERS TEST SET

AMIV 66 stand alone

Case
Case: aluminium, with carrying handle.

Accessories supplied with the unit

3X
3X
3X
1X
1X

. Protective plastic bag.
. Mains supply cable to DRTS 6.
. Interconnecting cable to DRTS 6.

CURRENT
A

POWER
VA

ZMAX
Ohm

0...15
0...1.5
0...0.15
0...15
0...45

80

0.35
0.35
0.35
0.71
0.12

160
240

RESOLUTION
230 µA
23 µA
2.3 µA
230 µA
0.69 mA

AMIV 66
Three phase current and two phase voltage
amplifier
The three phase current and two phase voltage amplifier
AMIV 66 is an accessory for the DRTS 6 for tests that require
nine independent currents at the same time (two secondary
differential transformers), or six voltages at the same time
(synchronising devices), or six currents and six voltages.
The three current outputs of AMIV 66 can be generated together
with DRTS 6: this also allows paralleling current outputs, thus
increasing output current and power.

AMIV 66 stand alone
. Three independent current sources, with a common neutral.
. Automatic range switch and independent range selection.
. Waveform resolution: 28 bit.
. Output accuracy: ± 0.1% of the output, ± 0.02% of the range.
. Distortion: 0.1% total maximum, with any load.
. Automatic protection for overloads.
. Angle accuracy: ± 0.05°.

Two phase voltage generator
AMIV 66 with DRTS 6

6X
6X
6X
1X
1X

AMIV 66 with DRTS 6

9X
9X
9X
3X
3X
3X
1X

0...15
0...1.5
0...0.15
0...45
0...4.5
0...0.45
0...135

POWER
VA

ZMAX
Ohm

80

0.35

240

0.12

720

0.04

POWER
VA

ZMAX
Ohm

0...300
0...125
0...12.5
0...600
0...300

85
85
8
400
400

1060
185
185
200
50

VOLTAGE
V

POWER
VA

ZMAX
Ohm

0...300
0...125
0...12.5
0...600
0...300

100
100
10
200
200

900
160
160
1800
450

RESOLUTION

4.6
1.9
190
9.2
4.6

mV
mV
µV
mV
mV

AMIV 66 stand alone

Three phase current generator
CURRENT
A

VOLTAGE
V

RESOLUTION
230 µA
23 µA
2.3 µA
690 µA
69 µA
6.9 µA
2 mA

2X
2X
2X
1X
1X

RESOLUTION

4.6
1.9
190
9.2
4.6

mV
mV
µV
mV
mV

5

DRTS 6

AMIV 66 stand alone
. Two independent voltage sources, with a common neutral.
. Output frequency: from 0 Hz to 2000 Hz; transient 5 kHz.
. Waveform resolution: 28 bit.
. Output accuracy: ± 0.1% of the value, ± 0.02% of the range.
. Distortion: 0.1% total maximum, with any load.
. Automatic protection for overloads and counter-feed.
. Angle accuracy: ± 0.05°.

Power supply
Power supply voltage: 90 to 264 V AC single phase.
Frequency: 47 to 63 Hz.
Power consumption:
. stanby: less than 100 W;
. maximum load: 500 W.

Case
Aluminium, with carrying handle.

Accessories supplied with the unit
. Power supply cable.
. Relay connection cables kit.
. Interconnecting cable to DRTS.6.
. Plastic carrying bag.

Weight and dimensions
Weight: 18 kg.
Dimensions: 170 (h) x 470 (w) x 360 (d) mm.

AMV 66
Two phase voltage amplifier
The two phase voltage amplifier AMV 66 is an accessory for
the DRTS 6, for tests that require six voltages at the same
time (synchronising devices).

Two phase voltage generator
AMV 66 with DRTS 6

6X
6X
6X
1X
1X

VOLTAGE
V

POWER
VA

ZMAX
Ohm

0...300
0...125
0...12.5
0...600
0...300

80
80
320
320

1125
195
195
195
50

VOLTAGE
V

POWER
VA

ZMAX
Ohm

0...300
0...125
0...12.5
0...600
0...300

80
80

1125
195
195
390
97

4.6
1.9
190
9.2
4.6

mV
mV
µV
mV
mV

AMV 66 stand alone

2X
2X
2X
1X
1X

160
160

RESOLUTION

4.6
1.9
190
9.2
4.6

mV
mV
µV
mV
mV

AMV 66 stand alone
. Two independent voltage sources, with a common neutral.
. Output frequency: from 0 Hz to 2000 Hz; transient 5 kHz.
. Waveform resolution: 28 bit.
. Output accuracy: ± 0.1% of the output, ± 0.02% of the range.
. Distortion: 0.1% total maximum, with any load.
. Automatic protection for overloads and counter-feed.
. Angle accuracy: ± 0.05°.

Power supply
Power supply voltage: 90 to 264 V AC single phase.
Frequency: 47 to 63 Hz.
Power consumption, maximum load: 500 W.

Case
Aluminium, with carrying handle.

Accessories supplied with the unit
. Power supply cable.
. Interconnecting cable to DRTS 6.
. Plastic carrying bag.

6

RESOLUTION

DRTS 6

RELAYS, ENERGY METERS AND TRANSDUCERS TEST SET

Weight and dimensions
Weight: 7 kg.
Dimensions: 170 (h) x 230 (w) x 360 (d) mm.

OPTIONAL ACCESSORIES
IEC61850 INTERFACE
The standard IEC61850 describes the communication of
devices in substations. IEC61850 messages coming from the
devices connected to the substation network (such as a relay)
are also called GOOSE. GOOSE messages describe binary
status signals over the substation network and are also used
for relays tripping . For relay testing applications within IEC
61850 substations it is necessary to access to these data.
This new feature is performed by ISA Automatic Relay Test Set
DRTS 6 and with the TDMS software.
By means of a dedicated hardware and the TDMS software, ISA
DRTS 6 can expand his testing capabilities by handling those
IEC61850 messages.
The IEC61850 Interface option for DRTS 6 is required for
relay testing with Ethernet-based substation communication
protocol. The IEC61850 Interface is mounted directly on the
front panel of the DRTS 6.

Primaries: 12.5 A and 15 A;
Secondaries: 0.5 A; 1 A; 2.5 A; 5 A;
Nominal power: 100 VA;
Current ratio error: 0.2.
Case: plastic.
For the single phase test of the CDG relay it is possible to
have three times the above power, connecting current
outputs in series.

I100A CURRENT BOOSTER
The option I100A is a set of six current transformers, that
allows to perform the following tests:
- With DRTS 6, 3x50 A;
- With DRTS 6 and AMI 99, 6X50 A (differential relays) or
3x100 A (over-current relays).
Characteristics:
Primary: 3x(2x15) +3x30 A;
Secondary: 6x50 A, that can be put in parallel, to form 3x100 A;
Nominal power: 6x120 VA @ 50 A, or 3x240 VA, steady;
Current ratio error: 0.5;
Frequency range: 40 Hz to 2 kHz.
Case: plastic.
Dimensions: 400 x 300 x 175 mm.
Weight: 12 kg.
Inputs from DRTS 6 are put in parallel inside the option:
all transformers have 30 A on the primary and 50 A on the
secondary.
The option includes twelve connecting cables to DRTS 6 and
AMI 99 current outputs.

GPS SYNCHRONIZER
The GPS synchronizer is an external module that allows to
synchronize the test start of two DRTS 6.

IN2-CDG CURRENT BOOSTER FOR 1 A RATED
HIGH BURDEN RELAYS
With DRTS 6 the full power of 100 VA is available only at the
current of 15 A. The option IN2-CDG by means of a set of three
current transformers, has the following characteristics:

7

DRTS 6

Features:
. 1 digital output O-24 V DC, for synchronization.
. 1 selector to program the following pulse intervals: 5 s; 10 s;
20 s; 30 s; 40 s; 60 s.
. Maximum timing error with respect to nominal: 2 µs.
. Lights to confirm: power-on; Locked; Pulse available.
. 1 START and STOP push-button.
. Power supply: 110/22O V AC.
The option includes:
. the antenna;
. an extension cable for the antenna, 20 m long;
. two cables, red and black, 2 m long, with banana
terminations, for the connection to the test set trip input;
. the power supply cable.
Weight: 1.7 kg.
Dimensions: 150 (w) x 100 (h) x 240 (d) mm.
Case: aluminium.
Two test sets synchronized with GPS produce the maximum
error of 50 µs.

The option includes:
. A support to keep the scanning head in front of the energy
meter;
. The cable, 2 m long, from the scanning head to the DRTS 6;
. The power supply transformer, for the power of 220 V AC, to
supply the scanning head.
. Two safety banana plugs for the connection to DRTS 6.

TRANSIT CASE
Three options are available:
. Heavy duty transit case (Discovery type) in black plastics,
with handle and wheels.
. Heavy duty transit case in aluminium, with handle and
wheels.
. Soft carrying bag.

TESTING CABLES
This option includes additional cables, with different colours.

SH 2003 ENERGY METERS UNIVERSAL SCANNING HEAD
SH 2003 is a scanning head that eases the test of energy
meters. lt is an universal scanning head because it can be used
both with LED impulse electronic meters and Ferraris rotating
disk meters. With rotating disk the sensor uses a green light
beam that optimizes the recognition of any type of mark.

SEI OPTION FOR THE SERIES CONNECTION OF
CURRENTS
This option is made of a set of three burdens that equalize
the load for current outputs of DRTS 6. Each burden includes
two resistors rated 22 Ohm 1 W; at maximum load it causes
an error of – 1.6 %. The burden is easily connected to current outputs by means of three safety banana sockets plus
plugs, that ease connections.

PAV OPTION FOR THE PARALLEL CONNECTION
OF VOLTAGES

With LED recognition the following specification applies:
. lmpulse duration: more than 60 µs.;
. lmpulse frequency: less than 500 Hz;
. Light wavelength: 500 to 960 nm (red).

8

The option includes small resistors to be connected in
series to voltage outputs of DRTS 6 and of AMV 66 or AMIV
66 options. Burden is 1 Ohm for tests up to 125 V and 5.7
Ohm for tests at 300 V; at maximum load it causes an error
of – 0.5%.
- Case: plastic.
- Dimensions: 22 x 45 x 85 mm.
- Connections to the instrument: two wires 0.2 m long, with
safety banana plugs.
- Connection to the load: by a safety banana plug.
- 125 V or 300 V selection: by switch.

DRTS 6

RELAYS, ENERGY METERS AND TRANSDUCERS TEST SET

PAI OPTION FOR THE USE AT 30 A, THREE
PHASE
The option PAI is made of four jumpers, that ease the paralleling of output sockets: I1 and I4; I2 and I5; I3 and I6, and
of the two IN sockets: this eases the connection to the relay
under test.

ORDERING INFORMATION
CODE
30156

MAINS SYNCHRONISER
The option is made of a plug that fits into the mains, and
that has two banana sockets for the connection to the
test set counting input. The purpose is to synchronize the
outputs of two test sets to the mains: as the synchronisation is repeated every 2 minutes, the test set stays locked
to the mains for the infinity. The option includes a circuit
that squares the sinusoidal mains waveform; the isolated
output is a square-wave with an amplitude of 18 V nominal,
running at the mains frequency.
There are two instances where the option can be necessary:
. Generating a current or voltage into a device that is also
taking a signal from the mains;
. Synchronising two test sets to the mains, and then using
them to test line differential relays.

STAND UP SUPPORT
The stand-up support allows using the test set in a stand-up
position. This is very useful in case of too small room or no
support for the test set. There is enough room for the power
supply cord, and for the cooling air to flow in.

MODULE
DRTS 6
6 x I 0...15 A - 4 x V 0...300 V
1 x VDC output 0...260 V at 100 W
Standard set of test cables
Soft carry bag
TDMS - Test & Data Management Software

OPTIONAL ACCESSORIES
CODE
19153
23156
81156
98156
47156
10161
20162
15156
77156
18156
48156
35150
36156
34156
24156
19170
59156
58156

MODULE
Analog AC/DC Measurement Module
High Precision (HP) outputs; 0.05% accuracy
outputs with SIT laboratory certificate (EU
accreditated)
IEC61850 Interface, hardware and software
IN 2 CDG - Option for High Burden Relays
I 100 - 100 A Current Booster
GPS syncronizer
SH 2003 energy meter universal scanning
head
Additional set of test cables
Heavy duty transport case (Discovery type)
Aluminium transport case
Soft carrying bag
SEI option to put in serie the current outputs
PA-I option to put in parallel the current
output (3 x 30A)
PA-V
Mains synchronizer
Stand up support
Thytronic thysensor cables set
ABB zero power cables set

APPLICABLE STANDARD
The test set conforms to the EEC directives regarding
Electromagnetic Compatibility and Low Voltage instruments.
A) Electromagnetic Compatibility:
Directive 2004/108/EC (CE conform). Applicable standard:
EN 61326:2006.
B) Low Voltage Directive:
Directive 2006/95/EC (CE conform).
. Applicable standards, for a class I instrument, pollution
degree 2, Installation category II: CEI EN 61010-1.
In particular:
. Inputs/outputs protection: IP 2X - CEI EN 60529.
. Operating temperature: 0°C to 55°C;
storage: -25°C to 70°C.
. Relative humidity: 5 - 95% without condensing.

EXTERNAL AMPLIFIERS
CODE

MODULE

27156
28156
13156

AMI-99 (3 x I - 0 … 30 A at 160 VA)
AMV-66 (2 x V - 0 … 300 V at 80 VA)
AMIV-66 (3 x I - 0 … 15 A at 80 VA)
(2 x V - 0 … 300 V at 80 VA)

OPTIONAL ACCESSORIES FOR EXTERNAL
AMPLIFIERS
CODE
15156
18156

MODULE
Set of testing cables
Aluminium Transport Case
9

DRTS 6

10

AMI 99 - External amplifier

Heavy duty transport case

AMIV 66 - External amplifier

Heavy duty transport case in aluminium

AMV 66 - External amplifier

Soft bag

DRTS 6

Optional set of testing cables

Standard set of testing cables

ISA Srl
Via Prati Bassi, 22
21020 Taino VA - Italy
Tel +39 0331 956081
Fax +39 0331 957091
Web site: www.isatest.com
E-Mail: isa@isatest.com
11

Stand up support

EN - DRTS 6 - 06/2014

IN 2 CDG - Option for High Burden Relays

The document is subject to change without notice.
Always refer to our technical specification for more detailed
information and as formal contract document.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : sassib
Create Date                     : 2014:06:11 14:33:45+02:00
Modify Date                     : 2014:06:11 14:44:39+02:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:06:11 14:44:39+02:00
Format                          : application/pdf
Title                           : DRTS 6 _GB.indd
Creator                         : sassib
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Document ID                     : uuid:a68dff9c-3e9a-4f40-a0f9-4e0ff6160bc4
Instance ID                     : uuid:aecd7a2b-04db-4b11-ab17-888b371b153f
Page Count                      : 11

EXIF Metadata provided by EXIF.tools