小型環境_e_ D250 (115V) Espec SH 641 Datasheet
User Manual: D250 (115V)
Open the PDF directly: View PDF 
.
Page Count: 14
| Download | |
| Open PDF In Browser | View PDF |
® E stablished 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Bench-Top Type Temperature (& Humidity) Chamber SH･SU CAT.NO.E01111-K1209 Characteristics Full variation to select from With its 3 temperature range patterns (to −60, −40 or −20℃), and 2 volumes (20 and 60L) selection, the Bench-top chambers offer 10 models in temperature or temperature/ humidity configuration, to fulfill customers' needs. Light and small structure The chamber structure is optimized to save space while offering a wide test area (22.5L for 1st model). Its relatively l ig ht we ig ht a l lows s e t u p a l mo s t everywhere. Stacked chambers (on stands) Full-size chamber performance in a compact design The SH-661 model achieves −60 to ＋150℃ temperature range and 30 to 95％ rh for humidity in a small structure. It shows undoubtedly better performance than any other previous bench-top model. A refrigeration system that reduces energy consumption by 55% Our exclusive refrigerator system with capacity control achieves 55％ reduction in power consumption compared to our previous model. (SH/SU-221･241 models) Test area (60L model) Easy wiring access The chamber features free access to the test area. Cable ports are provided on both right and left side to allow easy wiring of specimens for measurement or voltage application. 3 Characteristics Layout arrangement thanks to additional stand (option) L and H stands are equipped with casters, and allow easy storage to optimize your testing zone. L stand is lower to fit under H stand and stack chambers. (L=Low, H=High) * It is recommended to secure stands to the floor with provided anchor bolts. Easy water supply Water is supplied from the front side tank (equipped with a level sensor). Auxiliary water tank circuit (option) is also available for extended operation time. (SH model) Right-opening door (option) The door opening can be reversed to fit your installation space. Stands (option) Viewing window (option) An optional viewing window can be added to check specimens and wiring during testing. ( W215 × H 215m m fo r 20L mo d el , W215×H315mm for 60L model) * Standard performance of the chamber will not be met when adding this option. Water supply tank Right-opening door (option) Viewing window (option) 4 Characteristics Ion migration evaluation The Bench-top chamber can be combined with ESPEC's Ion Migration Evaluation System (AMI) to ensure even more accurate evaluation results. Paperless recorder (option) Portable type, to record temperatures from various sources, such as test area temperature. Recording is possible on Compact Flash Card or via USB port. Material labeling for easy recycling Example: Bench-top Type Temperature (& Humidity) Chamber connected with the Ion Migration Evaluation System (sold separately) Paperless recorder Portable type (option) 5 Cable port plug (Material marked) Plastic molded components are labeled and easily detachable to make recycling e a s ie r fo r f u t u r e d i s p o s a l of t h e equipment. Control operation Key input setting E a s y s e t t i n g of t e m p e r a t u r e a n d humidity values, but also upper and lower temperature (& humidity) limit alarms, by mechanical key input. Description of program function Program function Pattern Temp. 3 8 4 5 2 Step program 7 1 6 9 Program operation up to 9 steps Besides const ant set ting, prog ram o p e r a t io n i s ava i l a ble by s e t t i n g different patterns (9 step/ pattern) of heat up and pull down temperatures, to meet requi rements of temperat u re characteristic test or temperature (& humidity) cycling. The instrumentation additionally offers various functions. Time Temp. 3 Temperature gradient program 2 Remote control from your PC Using "WEB Manager" (converter sold separately) and an intranet to connect the chamber and a computer makes it possible to edit profiles and perform monitoring from the computer. 7 8 4 1 6 9 5 *1,2 Time 1.HOLD Temp. 2.CONST Retains value of last step Termination program Flexible communication interface An RS-485 connector is equipped as standard, but RS-232C or GP-IB is also available as option. *1,2 END END Operation at constant temp. END 3.OFF Time Chamber OFF Time Time *1 Sets a program repetition frequency between a range of 1 and 99. *2 Selects HOLD, CONST or OFF when a program is over. Temperature (& humidity) program indicator controller Setting Mechanical key input Display 7 segment LED display Operating mode Program operation, constant operation Control PID control Setting and indication Temp. : 0.1ºC Humid. : 1%rh (SH only) Time : 1 minute Setting and indication ranges Temp. : −25 to ＋155ºC (SH-221, SU-221) −45 to ＋155ºC (SH-241/641, SU-241/641) −65 to ＋155ºC (SH-261/661, SU-261/661) Humid. : 0 to 100%rh (SH only) Time : 0 to 99 hours 59 minutes, 100 to 999 hours Indication accuracy * Temp. : 0.5ºC (Typ.) Humid. : ±2%rh (Typ.) (SH only) Time : within 30 sec. per month Program memory capacity 9 steps per pattern (1 to 99 times) Interface RS-485 Auxiliary functions Input-burnout detection Upper and lower temp. (& humid.) limit alarm Self-diagnostic (watchdog timer) Alarm indication Power cut protection Refrigerator capacity automatic control Battery Lithium battery ×1 * At ambient temperature ＋23ºC 6 SH Model SH−221 SH−241 System −20 to ＋150℃ (−4 to ＋302℉) Temp. range Temp. performance *1 −40 to ＋150℃ (−40 to ＋302℉) Temp. Heat up rate rate of change Pull down rate −60 to ＋150℃ (−76 to ＋302℉) −40 to ＋150℃ (−40 to ＋302℉) −60 to ＋150℃ (−76 to ＋302℉) 3.2℃ /min. 3.2℃ /min. 3.2℃ /min. 2.9℃ /min. 2.9℃ /min. 2.1℃ /min. 2.1℃ /min. 2.1℃ /min. 1.7℃ /min. 1.7℃ /min. Heat up time From −20 to ＋150℃ From −40 to ＋150℃ From −60 to ＋150℃ From −40 to ＋150℃ From −60 to ＋150℃ within 55 min. within 60 min. within 70 min. within 70 min. within 80 min. Temp. extreme achievement time Pull down time From ＋20 to −20℃ within 20 min. From ＋20 to −40℃ within 50 min. From ＋20 to −60℃ within 70 min. From ＋20 to −40℃ within 60 min. From ＋20 to −60℃ within 90 min. −20℃ −40℃ −60℃ −40℃ −60℃ Humid. range 30 to 95％rh (Refer to diagram on page 9) Humid. fluctuation ±3.0％rh Heater Nichrome strip wire heater Refrigeration unit Humidifier Construction SH−661 Temp. gradient / 2.5℃ (−20 to ＋100℃) 2.5℃ (−40 to ＋100℃) 2.5℃ (−60 to ＋100℃) 2.5℃ (−40 to ＋100℃) 2.5℃ (−60 to ＋100℃) Temp. variation in space 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) Lowest attainable temp. Sheathed heater System Mechanical single-stage refrigeration system Mechanical cascade refrigeration system Cooler Plate fin cooler Refrigerator Hermetically sealed compressor, Air-cooled condenser, Expansion mechanism: Capillary tube system Refrigerator capacity 400W [Unit 1: 400W ×1, Unit 2: 400W ×1] Refrigerant R404A R23, R404A Capacity 22.5 L 64 L Chamber total load resistance 20 kg Inside dimensions mm (inch) *2 W300×H300×D250 (W11.81×H11.81×D9.84) Outside dimensions mm (inch) *2 W440×H630×D695 (W17.32×H24.80×D27.36) Weight 83 kg (78 for 100V type) Power supply *3 W400×H400×D400 (W15.75×H15.75×D15.75) W440×H690×D785 (W17.32×H27.18×D30.91) W540×H730×D920 (W21.26×H28.74×D36.22) 105 kg 130 kg ＋5 to ＋35℃ (＋41 to ＋95℉） Allowable ambient conditions Utility requirements SH−641 ±0.3℃ (−20 to ＋100℃) ±0.3℃ (−40 to ＋100℃) ±0.3℃ (−60 to ＋100℃) ±0.3℃ (−40 to ＋100℃) ±0.3℃ (−60 to ＋100℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) Temp. fluctuation Humid. performance *1 SH−261 Balanced Temperature & Humidity Control system (BTHC system) 100V AC 1φ50/60Hz 13.5 A 15.0 A 18.0 A 115V AC 1φ60Hz 13.0 A 14.5 A — 200V AC 1φ50/60Hz — 10.5 A 220V AC 1φ50/60Hz 8.0 A 9.5 A 10.0 A *4 8.0 A 9.5 A 10.0 A 230V AC 1φ50Hz *4 7.5 A 9.5 A 10.0 A 220V AC 1φ60Hz Noise level *5 Exhaust heat quantity 55 dB 59 dB 61 dB 3500 kJ/h (836 kcal/h) 4000 kJ/h (955 kcal/h) 5040 kJ/h (1204 kcal/h) *1 The performance values are based on IEC 60068-3-5:2001, JTM K07:2007 for the temperature chamber, IEC 60068-3-6:2001, JTM K09:2009 for the humidity chamber. Performance figures are given for a ＋23℃ ambient temperature, 65% rh, rated power supply and no specimens inside the test area. However, the lowest attainable temperature is given for a max. ambient temperature of ＋30℃. Heat-up time is the achieved time from lowest temperature to highest temperature within temperature range. *2 Excluding protrusions. *3 At ambient temperature ＋23℃. For SH-641/661, make sure to check the power capability of your installation beforehand. *4 Compliance with CE Marking. *5 Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel (ISO 1996-1:2003 _ A-weighted sound pressure level) 7 SU Model SU−221 SU−241 System −20 to ＋150℃ (−4 to ＋302℉) Temp. range Temp. performance *1 −40 to ＋150℃ (−40 to ＋302℉) Temp. gradient / 2.5℃ (−20 to ＋100℃) Temp. variation in space 4.0℃ (＋100.1 to ＋150℃) Temp. Heat up rate rate of change Pull down rate SU−661 −60 to ＋150℃ (−76 to ＋302℉) −40 to ＋150℃ (−40 to ＋302℉) −60 to ＋150℃ (−76 to ＋302℉) 2.5℃ (−40 to ＋100℃) 2.5℃ (−60 to ＋100℃) 2.5℃ (−40 to ＋100℃) 2.5℃ (−60 to ＋100℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 4.0℃ (＋100.1 to ＋150℃) 3.2℃ /min. 3.2℃ /min. 3.2℃ /min. 2.9℃ /min. 2.9℃ /min. 2.1℃ /min. 2.1℃ /min. 2.1℃ /min. 1.7℃ /min. 1.7℃ /min. Heat up time From −20 to ＋150℃ From −40 to ＋150℃ From −60 to ＋150℃ From −40 to ＋150℃ From −60 to ＋150℃ within 55 min. within 60 min. within 70 min. within 70 min. within 80 min. Temp. extreme achievement time Pull down time From ＋20 to −20℃ within 20 min. From ＋20 to −40℃ within 50 min. From ＋20 to −60℃ within 70 min. From ＋20 to −40℃ within 60 min. From ＋20 to−60℃ within 90 min. −20℃ −40℃ −60℃ −40℃ −60℃ Lowest attainable temp. Refrigeration unit Heater Nichrome strip wire heater System Mechanical single-stage refrigeration system Mechanical cascade refrigeration system Cooler Plate fin cooler Refrigerator Hermetically sealed compressor, Air-cooled condenser, Expansion mechanism: Capillary tube system Refrigerator capacity 400W [Unit 1: 400W ×1, unit 2: 400W ×1] Refrigerant R404A R23, R404A Capacity 22.5 L 64 L Chamber total load resistance 20 kg Inside dimensions mm (inch) *2 W300×H300×D250 (W11.81×H11.81×D9.84) Outside dimensions mm (inch) *2 Weight Power supply *3 W400×H400×D400 (W15.75×H15.75×D15.75) W440×H560×D695 (W17.32×H24.8×D27.36) W440×H620×D785 (W17.32×H24.41×D30.91) W540×H660×D920 (W21.26×H25.98×D36.22) 78 kg (73 for 100V type) 100 kg 123 kg ＋5 to ＋35℃ (＋41 to ＋95℉） Allowable ambient conditions Utility requirements SU−641 ±0.3℃ (−20 to ＋100℃) ±0.3℃ (−40 to ＋100℃) ±0.3℃ (−60 to ＋100℃) ±0.3℃ (−40 to ＋100℃) ±0.3℃ (−60 to ＋100℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) ±0.5℃ (＋100.1 to ＋150℃) Temp. fluctuation Construction SU−261 Balanced Temperature Control system (BTC system) 100V AC 1φ50/60Hz 11.0 A 15.0 A 18.0 A 115V AC 1φ60Hz 10.5 A 14.5 A — 200V AC 1φ50/60Hz 220V AC 1φ50/60Hz 220V AC 1φ60Hz *4 230V AC 1φ50Hz *4 Noise level *5 Exhaust heat quantity — 7.0 A 10.5 A 9.5 A 10.0 A 7.0 A 9.5 A 10.0 A 6.5 A 9.5 A 10.0 A 55 dB 59 dB 61 dB 3500 kJ/h (836 kcal/h) 4000 kJ/h (955 kcal/h) 5040 kJ/h (1204 kcal/h) *1 The performance values are based on IEC 60068-3-5:2001, JTM K07:2007 for the temperature chamber. Performance figures are given for a ＋23℃ ambient temperature, 65%rh, rated power supply and no specimens inside the test area. However, the lowest attainable temperature is given for a max. ambient temperature of ＋30 ℃. Heat-up time is the achieved time from lowest temperature to highest temperature within temperature range. *2 Excluding protrusions. *3 At ambient temperature ＋23℃. For SU-641/661, make sure to check the power capability of your installation beforehand. *4 Compliance with CE Marking. *5 Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel (ISO 1996-1:2003 _ A-weighted sound pressure level) 8 TEMPERATURE & HUMIDITY CONTROL RANGE (SH) FITTINGS Relative Humidity (%rh) ● 100 90 80 70 60 50 40 30 20 10 0 95％rh ● ● ● ● ● ● ● ● 10 20 15℃ 30 40 50 60 Temperature (℃) 70 80 90 100 ● Temperature-Humidity recorder terminal Specimen power supply control terminal External alarm terminal External output terminal Cable port Power cable Drain hose Water supply tank (SH only) Humidifying tray drain plug (SH only) Drain socket for water sensor box (SH only) 85℃ * At ambient temperature +23℃ ACCESSORIES ● MODEL S - 1 Temperature range 2: −20 to ＋150℃ 4: −40 to ＋150℃ 6: −60 to ＋150℃ ● Capacity 2: 22.5L 6: 64.0L H: Temperature & humidity chamber U: Temperature chamber ● ● ● ● SAFETY DEVICES ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 9 Leakage breaker Thermal fuse Boil dry protector (SH only) Control circuit short-circuit protective fuse Overheat and overcool protector Temperature switch for air circulator Specimen power supply control terminals Refrigerator overload relay Refrigerator high pressure switch Chamber door switch Upper and lower temperature (& humidity) limit alarms (Built-into temperature [humidity] controller) Burn-out detection circuit (Built-into temperature [humidity] controller) Watchdog timer (Built-into temperature [humidity] controller) Refrigerator automatic delay circuit (Built-into temperature [humidity] controller) ● Shelf 1 Capacity SH/ SU-221, 241, 261 : 500g SH/ SU-641, 661 : 5kg Max. number of shelves SH/ SU-221, 241, 261 : 5 (Shelf pitch 35mm) SH/ SU-641, 661 : 5 (Shelf pitch 50mm) Connector 2P for connecting terminal for temp. & humid. recorder SH:2/ SU:1 6P for connecting signal terminal 1 Cable port plug (φ25mm) 2 Cartridge fuse (Class A, 250V, 3A) 1 Socket adapter (100V, 115V on 20L type only) 1 Wet-bulb wick (Box of 24pcs) 1 (SH only) Humidifying tray drain hose 2m 1 (SH only) Drain hose for water sensor box 0.3m 1 (SH only) User's manual (CD-R, booklet) 1 set 70 (2.8) 70 (2.8) 30 150 (5.9) 540 (21.3) 70 (2.8) 300 (11.8) 695 (27.4) 920 (36.2) 250 (9.8) ● 440 (17.3) 300 (11.8) 70 (2.8) 70 (2.8) 70 (2.8) SH-221･241 440 (17.3) 510 (20.0) 690 (27.2) 300 (11.8) 440 (17.3) 510 (20.0) 630 (24.8) 440 (17.3) 400 (15.7) 540 (21.3) 610 (24.0) 730 (28.7) ● 250 (9.8) 300 (11.8) 30 90 (3.5) 30 90 (3.5) ● 400 (15.7) DIMENSIONS unit：mm (inch) SH-261 35 (1.4) 785 (30.9) 35 (1.4) 250 (9.8) 250 (9.8) SH-641･661 400 (15.7) 10 (0.4) 400 (15.7) 10 30 400 (15.7) 11 30 540 (21.2) 400 (15.7) 70 (2.8) 300 (11.8) 695 (25.7) SU-641・661 920 (36.2) 10 (0.4) 250 (9.8) ● 440 (17.3) 250 (9.8) 300 (11.8) 70 (2.8) 70 (2.8) 70 (2.8) SU-221・241 436.5 (17.1) 590 (23.2) 620 (24.4) 300 (11.8) 440 (17.3) 530 (20.8) 560 (22.0) 440 (17.3) 400 (15.7) 70 (2.8) 70 (2.8) ● 250 (9.8) 300 (11.8) 536.5 (21.1) 630 (24.8) 660 (25.9) 30 ● 400 (15.7) DIMENSIONS unit：mm (inch) SU-261 35 (1.4) 785 (30.9) 250 (9.8) 35(1.4) OPTIONS Paperless recorder (Portable type) Temperature recorder (Portable type) Viewing window Records temperature of each section such as the temperature inside the chamber. Data saving cycle: 5 sec Portable type External recording media: CF memory card (256MB) USB port Language support: ENG, JPN [SRJ25] Temperature range: −100 to ＋200℃ Effective recording chart width: 100mm Number of inputs: Temperature 6 SH/SU-221, 241, 261 W215×H215mm SH/SU-641, 661 W215×H315mm [Temperature type] Temperature range: −100 to ＋200℃ Number of inputs (Initial setting): Temperature 1 (5 more channels can be turned ON) [Temperature and humidity type] Temperature range: − 50 to ＋150℃ −100 to ＋150℃ Humidity range: 0 to 100%rh Number of inputs (Initial setting): Temperature 1 / Humidity 1 (4 more channels can be turned ON) Temperature & humidity recorder (Portable type) Effective recording chart width: 100mm Number of inputs: Temperature 5 Humidity 1 [SRJ14] Temperature range: −100 to ＋150℃ Humidity range: 0 to 100%rh (for SH) When equipped with a viewing window, chamber performance are as follow: Temperature uniformity : ±1.0℃ (−20 to ＋100℃) ±1.5℃ (−100.1 to ＋150℃) Humidity uniformity : ±5.0％rh Temp. heat up rate: Std rate ＋10 min. (or less) Temp. pull down rate: Std rate ＋10 min. (or less) (＋20 to −35℃) Std rate +30 min. (or less) (＋20 to −60℃) [SRJ12] Temperature range: −50 to ＋150℃/ Humidity range: 0 to 100%rh (for SH) W215×H215mm Inner door Wet-bulb temperature detecting terminal Paperless recorder Portable type For the test area wet-bulb temperature detection. A ther mocouple type T (C o p p e r / C o p p e r - N i c k e l ) o r o f equivalent thermoelectric capacity is used. Connector included. Glass door provided inside the chamber, t o obse r ve t he c ond it ion s of t he specimens. * A wiper is included for SH models. * This option is not compatible with a viewing window or right-opening door. * Used for observation of the specimens inside the chamber. * Not available for SU. Thermocouple Attached to specimens to measure specimen temperature. ・2m ・4m ・6m SU model * Thermocouple type T without ball (Copper / Copper-Nickel) * Same as accessory items 12 OPTIONS Right-opening door Auxiliary water tank circuit (SH) Stand Door can be changed for a reverse one (hinges on the right, handle on the left) Used to automatically refill the standard tank with the auxiliary water tank. Required water quality: Conductivity 0.1 to 10μS/cm Water supply pressure: 4.9 to 19.6KPa (Gauge) Enhances the mobility of the chamber, a n d f a c i l i t a t e s l o a d / u n l o a d of specimens. L stand can fit under the H stand to save space. * This option is not compatible with inner glass door option. Auxiliary water tank (SH) Used to refill the standard tank. Tray for auxiliary tank (SH) P revent s water lea kage du r i ng standard tank refill process. Additional cable port * Be sure to secure the stand to the floor with the provided anchor bolts. ・ L stand SH/SU-221, 241: W440×H450×D750mm (25kg) SH/SU-261: W440×H390×D750mm (21.5kg) SH/SU-641, 661: W540×H350×D860mm (28kg) ・ H stand SH/SU-221, 241, 261: W630×H1140×D815mm (36kg) SH/SU-641, 661: W730×H1140×D925mm (40kg) Shelf Provided in addition / replacement of the standard cable ports. ・ 25mm diameter ・ 50mm diameter ・ 100mm diameter ・ Flat cable port (W100×H25mm) * Each cable port is equipped with a silicone sponge rubber plug. * Basic specification of the chamber may not be met when equipped with a cable port. Equivalent to standard accessory: 〈SH/SU-221, 241, 261〉 Effective size: W200×D150mm Load resistance: 500gr. 〈SH/SU-641, 661〉 Effective size: W300×D300mm Load resistance: 5kg. Specimen basket Equivalent to standard accessory. Material: Stainless steel (5 mesh) 25mm diameter type L stand flat type Cable port rubber plug Prevents air leakage from the cable port. Two chambers stacked (L and H stands) ■Some photographs listed in this catalog contain Japanese display. ■This product can be customized for your needs. For further information, please contact us. 13 OPTIONS Interface ・GPIB ・RS-232C * Select one, instead of standard RS-485 Communication cables ・RS-485 ・GPIB ・RS-232C 5m/ 10m/ 30m 2m/ 4m 1.5m/ 3m/ 6m Safety precautions Do not use specimens which are explosive or inflammable, or which contain such substances. To do so could be hazardous, as this may lead to fire or explosion. ● Do not place corrosive materials in the chamber. If corrosive substances or liquid is used, the life of the unit may be significantly shortened specifically because of the corrosion of stainless steel, resin and silicone materials. ● ● Do not place life forms or substances that exceed allowable heat generation. ● Be sure to read the user's manual before operation. 14 http://www.espec.co.jp/english Head Office 3-5-6, Tenjinbashi, Kita-ku, Osaka 530-8550, Japan Tel : 81-6-6358-4741 Fax : 81-6-6358-5500 ESPEC NORTH AMERICA, INC. Tel : 1-616-896-6100 Fax : 1-616-896-6150 ESPEC EUROPE GmbH Tel : 49-89-1893-9630 Fax : 49-89-1893-96379 ESPEC (CHINA) LIMITED Tel : 852-2620-0830 Fax : 852-2620-0788 ESPEC ENVIRONMENTAL EQUIPMENT (SHANGHAI) CO., LTD. Head Office Tel : 86-21-51036677 Fax : 86-21-63372237 BEIJING Branch Tel : 86-10-64627025 Fax : 86-10-64627036 TIANJIN Branch Tel : 86-22-26210366 Fax : 86-22-26282186 GUANGZHOU Branch Tel : 86-20-83317826 Fax : 86-20-83317825 SHENZHEN Branch Tel : 86-755-83674422 Fax : 86-755-83674228 SUZHOU Branch Tel : 86-512-68028890 Fax : 86-512-68028860 ESPEC TEST TECHNOLOGY (SHANGHAI) CO., LTD. Tel : 86-21-68798008 Fax : 86-21-68798088 ESPEC SOUTH EAST ASIA SDN.BHD. Tel : 60-3-8945-1377 Fax : 60-3-8945-1287 Quality Management System Assessed and Registered ESPEC CORP. has been assessed by and registered in the Quality Management System based on the International Standard ISO 9001:2008 (JIS Q 9001:2008) through the Japanese Standards Association (JSA). ＊Registration : ESPEC CORP. (Overseas subsidiaries not included) TS9B24C03 (The contents of this catalog is as of September, 2012.) Environmental Management System Assessed and Registered ESPEC CORP. ● Specifications are subject to change without notice due to design improvements. ● Corporate names and trade names mentioned in this catalog are trademarks or registered trademarks.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : tsucky Create Date : 2012:09:10 10:11:47+09:00 Modify Date : 2015:05:01 09:59:45-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : Adobe InDesign CS3_J (5.0.4) Metadata Date : 2015:05:01 09:59:45-07:00 Producer : Acrobat Distiller 9.5.2 (Macintosh) Format : application/pdf Creator : tsucky Title : 小型環境_e_.indd Document ID : uuid:31bdfea2-b283-4791-b088-d6c23b1a328b Instance ID : uuid:8b552605-f400-44dc-bea1-f26697d5c385 Page Layout : TwoPageRight Page Count : 14EXIF Metadata provided by EXIF.tools