FA142cprogform FA142C Program Manual
User Manual: FA142C Program Manual AlarmHow.net Library
Open the PDF directly: View PDF 
.
Page Count: 24
| Download | |
| Open PDF In Browser | View PDF |
PROGRAMMING GUIDE (Includes Programming Form) FA142C SECURITY SYSTEM Addition of new 5800 series transmitters with this control panel is prohibited, other than for repair of existing installations. Non-permitted use voids U.S. warranty. NN7227–1 PRFA 4/97 TABLE OF CONTENTS Programming Form ................................................................................................ 3 Mechanics of Programming .................................................................................. 7 General Programming Information.................................................................... 7 Entering the Programming Mode....................................................................... 7 Programming a Data Field ................................................................................. 8 Reviewing a Data Field/Erasing an Entry in a Data Field ............................... 8 Interactive Menu Mode Programming (✱ 56, ✱ 80, ✱ 81, ✱ 82, & ✱ 83 .................. 8 Loading Factory Defaults ................................................................................... 8 Programming System Setup Fields .................................................................... 8 Exiting the Programming Mode ......................................................................... 8 5800 Series Transmitter Input Loop Identification ........................................ 9 Alpha Vocabulary List (For Entering Zone Descriptors) ................................... 10 Character (ASCII) Chart (For Adding Custom Words) ...................................... 10 Zone Response Type Definitions ....................................................................... 11 Data Field Descriptions ....................................................................................... 13 Remote Programming and Control (Downloading) ...................................... 20 General Information .......................................................................................... 20 Equipment Required ......................................................................................... 20 Initial Download ................................................................................................ 20 Remote Programming Information .................................................................. 20 Remote Programming Advisory Notes ............................................................. 21 Summary of Connections Diagram ........................................ Inside Back Cover (23) – 2– FA142C PROGRAMMING FORM Local programming requires the use of a 2-line Alpha keypad (e.g., FA550KP) . To set all program fields to First Alert default values: Key ✱97. [ ] = Default Value Function Programmed Values Field SYSTEM SETUP (✱ 20- ✱27) ✱20 INSTALLER CODE ✱21 QUICK ARM ENABLE ✱22 RF SYSTEM TYPE [0 = none]; 1 = 5700 (4281); 2 = 5800 (5881) ✱23 FORCED BYPASS FUNCTION ✱24 RF HOUSE ID CODE [0][0] ✱25 WIRED EXPANSION/RELAY USED [0 = none]; 1 = bypass open zones 2 = bypass open zones + (if in system) zones 17, 30, 31, 46, 47. MUST enter (01-31) for 5700 System. Enter also for 5827 or 5827BD Keypad. [0 = none]; 1 = 4219; 2 = 4229; 3 = 4204 ✱26 VOICE MODULE ACCESS CODE ✱27 OUTPUT TO LONG RANGE RADIO ÊÊ Enter 4 digits, 0-9...[4] [1] [1] [1] [0 = no]; 1 = yes Ê 1st digit: Enter 1Ð9; 2nd digit: Enter only #+11 for '✴', #+12 for '#'. [0] in either position = disabled. ÊÊ[0 = no]; 1 = yes If yes selected, dialer reports to PRIMARY No. (field ÊÊÊ ✴47) will also be sent via LRR. All dialer and LRR reports will be in Contact ÊÊÊID format (overriding field ✴46 selection). ZONE SOUNDS AND TIMING (✱ 28- ✱39) ✱28 SINGLE ALARM SOUNDING/ZONEÊ ÊÊ ✱29 FIRE SOUNDER TIMEOUT [0 = fire sounder timeout]; 1 = no fire sounder timeout ✱30 ALARM BELL TIMEOUT 0 = none; [1= 4 min]; 2 = 8 min; 3 = 12 min; 4 = 16 min. ✱38 ENTRY DELAY 0 = 0 sec ; 1= 20 sec; [2 = 30 sec]; 3 = 45 sec; 4 = 60 sec; 5 = 90 sec EXIT Delay = ENTRY Delay + 15 sec ✱39 AUDIBLE EXIT WARNING 0 = no; [1 = yes] DIALER PROGRAMMING ( ✱40- ✱50) ✱40 [0 = no]; 1 = yes In fields ✴40, ✴ 41, ✴42, enter up to the number of digits shown. Do not fill unused spaces. Enter 0-9; #+11 for ' ✴'; #+12 for '#'; #+13 for a pause. PABX ACCESS CODE Enter up to 4 digits. If fewer than 4 digits entered, exit by pressing ✴ (and press 41, if entering next field). To clear entries from field, press ✴ 40 ✴. ✱41 PRIMARY PHONE No. ✱42 SECONDARY PHONE No. ✱43 SUBSCRIBER ACCT No. Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing ✴ (and press 42, if entering next field). To clear entries from field, press ✴41 ✴. Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing ✴ (and press 43, if entering next field). To clear entries from field, press ✴42 ✴. Enter 0-9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F]. Enter ✴ as 4th digit, if 3+1 dialer reporting is to be used. If only 3 digits used, exit by pressing ✴(and press next field). To clear entries from field, press ✴43 ✴. Examples: For Acct No. 1234 , enter: 1 2 3 4 For Acct No. B234, enter: For Acct No. 123, enter: ✱45 PHONE SYSTEM SELECT ✱46 REPORT FORMAT Ê Entry of a number other than one ÊÊÊspecified will give unpredictable ÊÊÊresults. ✱47 #+11 2 3 4 1 2 3 ✴ If Cent. Sta. IS NOT on a WATS line:[0 = Pulse Dial]; 1 = Tone Dial If Cent. Sta. IS on a WATS line: 2 = Pulse Dial ; 3 = Tone Dial Also see field ✴ 27. [0 = 3+1, 4+1 ADEMCO L/S STANDARD] 1 = 3+1, 4+1 RADIONICS STANDARD 2 = 4+2 ADEMCO L/S STANDARD 3 = 4+2 RADIONICS STANDARD SPLIT/DUAL REPORTING ** A 10-digit code is sent to the pager consisting of ÊÊÊÊa 4-digit Subscriber #, a 3-digit Event code, & a ÊÊÊÊ3-digit User or Zone #. See DATA FIELD ÊÊÊÊDESCRIPTIONS in this manual for an ÊÊÊÊexplanation of the 10-digit code. 6 or undefined = 4+2 ADEMCO EXPRESS 7 = ADEMCO CONTACT ID REPORTING 8 = 3+1, 4+1 ADEMCO L/S EXPANDED 9 = 3+1, 4+1 RADIONICS EXPANDED [0] ÊÊÊÊÊÊÊÊÊ0 = Disable (Backup report only) TO PRIMARY PHONE No. TO SECONDARY PHONE No. 1 = Alarms, Restore, Cancel Other Reports 2 = All Reports except Open/Close, Test Open/Close, Test 3 = Alarms, Restore, Cancel All Reports 4 = All Reports except Open/Close, Test All Reports 5 = All Reports ( Dual Reporting) All Reports TO PRIMARY PHONE No. TO PAGING No.* (SECONDARY) 6 = All reports except Open/Close ** Alarms, Open/Close, Troubles 7 = All reports ** Alarms, Troubles 8 = All reports ** Alarms, Open/Close, Troubles 9 = All reports except Open/Close ** Alarms, Open/Close for Users 5 Ð25, * Can only be used if Primary reporting is Ademco Contact ID. – 3– ✱48 15 SEC DIALER DELAY (BURG) [0 = no]; 1 = yes ✱49 PERIODIC TEST MESSAGE [0 = none]; 1 = 24 hrs; 2 = wkly; 3 = monthly. Enter Test Code in field ✴ 64. ✱50 SESCOA/RADIONICS SELECT [0 = Radionics (0-9, B-F reporting)]; 1 = SESCOA (0-9 only reporting) Ê Select 0 for all other formats. ✱51 CONFIRMATION OF ARMING DING [0 = no]; 1 = yes; 2 = yes, but with RF arming only. ZONE 3 RESPONSE TO OPEN [0 = 400 ms nominal]; 1 = 10 ms nominal ✱52 Ê Entry ✱56 of a number other than one specified will give unpredictable results. (See explanation on next page) → ZONE ASSIGNMENT/ALARM REPORT CODES ZONE No. (Zn) ZONE DESCRIPTION ZONE TYPE (ZT) ALARM RPT CODE (Hex) (RC) INPUT DEVICE (In) ENROLLED RF INPUT (L) Wired Zone 1 0 1 HW Ñ Wired Zone 2 0 2 HW Ñ Wired Zone 3 0 3 HW Ñ Wired Zone 4 0 4 HW Ñ Wired Zone 5 0 5 HW Ñ Wired Zone 6 0 6 HW Ñ 0 7 Ñ Ñ 0 8 Ñ Ñ Ñ Ñ 0 5 Keypad Panic (✴ & #, or B) Duress Tamper 0 9 Ñ Ñ Keypad Panic (1 & ✴, or A) 9 5 Ñ Ñ Keypad Panic (3 & #, or C) 9 6 Ñ Ñ EXPANSION ZONES: 4219/4229 Loop A, 4219/4229 can add up to 8 wired expansion zones. With 4281L, up to 4 RF expansion zones also available; 4281M/5881L, up to 8; 5881M, up to 16; 4281H/5881H, up to 30 (minus, in the last case, the number of 4219/4229 zones used). 1st Exp'n Zone B, 2nd C, 3rd D, 4th E, 5th F, 6th G, 7th H, 8th 9th 10th 11th 12th 13th 14th 15th 16th 17th 18th 19th 20th 21st 22nd 23rd 24th 25th 26th 27th 28th 29th 30th –4– ENTER FOR [5800 0NLY[ I N TH E P R E V I O U S P A G E ' S Z O N E A S S I G N M E N T T A B L E : Zn = ZONE NUMBER Zone Nos. are from 01 to 63, 95, 96. Some are pre-assigned. With Field ✴25 set for auxiliary wired loops (4219 or 4229), use Zone Nos. 10Ð17 for loops A-H. With Field ✴22 set for RF (5700 or 5800), use Zone Nos. 18-63 if 4219/4229 is ALSO used, or 10-63 if 4219/4229 is NOT used. ZT = ZONE TYPE 00 = Zone Not Used 05 = Trouble Day/Alarm 10 = Interior w/Delay DEFAULT VALUES 01 = Entry/Exit ÊÊÊÊÊÊÊÊÊNight 20 = ArmÐStay* Zn: 01 02 03 04 05 02 = Do not use 06 = 24 Hr Silent 21 = ArmÐAway* ZT: [01] [04] [03] [03] [09] 03 = Perimeter 07 = 24 Hr Audible 22 = Disarm* Zn: 06 07 95 96 04 = Interior Follower 08 = 24 Hr Aux 23 = No Alarm ZT: [07] [06] [00] [00] 09 = Fire ÊÊÊÊÊÊÊÊResponse * Used for 5800 RF systems only RC = ALARM REPORT CODE Two Hex Digits. For each Hex Digit, enter: 00Ð09 for 0Ð9, 10 for A, 11 for B, 12 for C, 13 for D, 14 for E, 15 for F. If "00" is entered in the first pair of boxes, there will be no report for that zone. For contact ID reporting, this is an enabling code only. Make any hex digit entry (other than "00") in the first pair of boxes. The second pair of boxes will be ignored. In = LOOP INPUT DEVICE HW: Hard Wire Enter 3 for RF: Supervised RF These are automatically AW: Aux Wire (4219 or 4229) Enter 4 for UR: Unsupervised RF assigned, except "UR" Enter 5 for BR: Button Type RF and "BR" for 5800 RF. L = RF INPUT LOOP Used with 5800 RF Loop Input Devices. TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✴ 60-✴ 75): With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1-9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. A "0" ( not "#+10") in the first box will disable a report. A "0" ( not "#+10") in the second box will result in automatic advance to the next field when programming. With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1-9, 0, or B-F, as described above. A "0" ( not "#+10") in the second box will eliminate the expanded message for that report. A "0" ( not "#+10") in both boxes will disable the report. With Ademco Contact ID Reporting: Enter any digit (other than "0") in the first box, to enable zone to report (entries in the second boxes will be ignored). A "0" ( not "#+10") in the first box will disable the report. Examples: For Code 3 (Single Digit), enter: 3 0 For Code 32 (Two Digits), enter: For Code B2 (Hexadecimal) enter: 3 #+11 ✱ SYSTEM STATUS REPORT CODES ( 60-✱ 68) ✱74 LOW BAT RESTORE RPRT CODE ✱75 RF XMTR LO BAT RST RPRT CODEÊ OUTPUT AND SYSTEM SETUP (✱ 80-✱ 92) ✱80 OUTPUT RELAYS Program only if Relays are to be used. See next page. ZONE LISTS FOR OUTPUT RELAYS CUSTOM ALPHA EDITING: (Also entered from field ✴56): See procedure in instructions. SEQUENTIAL MODE (Used for enrolling transmitters in ✱81 ✱82 ✱83 ✱91 a 5800 RF system after all other zone information has been programmed.) CUSTOM OPTION SELECTION (See field ✴ 98) = None selected] 4 = AAV (Audio 6 = Sounder Delay 1 = Local Lockout Alarm Veri+ AAV 2 = Sounder Delay fication) 7 = Local Lockout 3 = Local Lockout 5 = Local Lockout + Sounder Delay + Sounder Delay + AAV + AAV ÊÊ[0 2 2 ✱92 REPORTS PER ARMED PERIOD [0 = 10 max total alarm + alarm restore], 1 = unlimited DOWNLOAD INFO (✱ 94, ✱ 95) ✱94 DOWNLOAD PHONE No. ✱60 TROUBLE REPORT CODE ✱61 BYPASS REPORT CODE ✱62 AC LOSS REPORT CODE Enter up to 12 digits: 0-9; #+11 for ' ✴'; #+12 for '#'; #+13 for a pause. Do not fill unused spaces. If fewer than 12 digits entered, exit field by pressing ✴ (and press 95, if entering next field). To clear entries from field, press ✴ 94 ✴. ✱63 LOW BATTERY REPORT CODE ✱64 TEST REPORT CODE ✱65 OPEN/EXIT ALARM RPRT CODE / 2nd digit of OPEN REPORT is automatically sent as the user number if expanded or 4+2 reporting is selected. 2nd digit of EXIT ALARM REPORT is automatically sent as the 2nd digit of the zone alarm report code programmed in ✴56, if expanded or 4+2 reporting is selected. ✱66 AWAY/STAY CLOSE RPRT CODE / 2nd digit of any CLOSE REPORT is automatically sent as the user number, if expanded or 4+2 reporting is selected. ✱95 RING DET COUNT FOR DOWNLOADING [0=Disable Station Initiated Download]; 1Ð14 = number of rings (1-9, #+10=10, #+11=11, #+12=12, #+13 =13, #+14=14); 15=answering machine defeat (#+15 =15) ✱96 INITIALIZES DOWNLOAD ID , SUBSCRIBER ACCOUNT No. FOR INITIAL DOWNLOAD: No entry required. ✱97 SETS ALL PROGRAM FIELDS TO DEFAULT VALUES: No entry required. TO EXIT PROGRAM MODE (✱ 98 or ✱ 99) Press ✴98 or ✴ 99 if exiting programming, or next field number if continuing. ✱67 RF XMTR LOW BAT RPRT CODE ✱68 CANCEL REPORT CODE RESTORE REPORT CODES (✱ 70-✱ 75) ✱70 ALARM RESTORE RPRT CODE 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in ✴56, if expanded or 4+2 re porting is selected. ✱71 TROUBLE RESTORE RPRT CODE ✱72 BYPASS RESTORE RPRT CODE ✱73 AC RESTORE RPRT CODE –5– ✱98 EXITS PROGRAMMING MODE and prevents re-entry by (or, if Local Lockout has been chosen in field ✴91, allows re-entry only by): Master Code + Code + 0. ✱99 EXITS PROGRAMMING MODE and allows re-entry by: Master Code + Code + 0 or by: Power-up + ✴ + #. OUTPUT RELAYS WORKSHEET FOR FIELDS ✱80, and ✱81. Applicable only if relays are to be used. Fill in required data and follow detailed programming procedure described for Output Relays in the Installation Instructions. ✱80 OUTPUT RELAYS Notes: 1. 2. 3. Field ✴25 must be programmed for a 4229 (Relays 01 and 02) or a 4204 (Relays 01 to 04). If an AAV (Audio Alarm Verification) option is selected in field ✴91, Relay 01 should not be programmed here. Tampers of contacts or expansion units cannot be used to operate relays. S T A R T RELAY ACTION (A) OUTPUT RELAY S T O P =either or both EVENT (EV) ZONE LIST (ZL) =either or both - ZONE TYPE /SYST OP'N (ZT) "RESTORE of" ZONE LIST (ZL) ZONE TYPE /SYST OP'N (ZT) 01 SEE NOTE 2 ABOVE 02 03 04 Where: ✱81 A = RELAY ACTION EV = EVENT ZL = ZONE LIST 0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off 0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble 1, 2, or 3 (from Field ✴ 81) or 0 = Not Used. START ZONE LIST : Upon alarm, fault, or trouble of ANY zone on this list, relay action will START. STOP "RESTORE of" ZONE LIST: Upon restore of ALL zones on this list, relay action will STOP. ÊÊÊÊÊIt need not be same list as used for START. ZT = ZONE TYPE/SYSTEM OPERATION Choices for Zone Types are: 00 = Not Used 06 = 24 Hr Silent Note : Any zone in "ZT" going into alarm, 01 = Entry/Exit 07 = 24 Hr Audible fault, or trouble will actuate relay. 03 = Perimeter 08 = 24 Hr Aux Any zone of that type that restores 04 = Interior Follower 09 = Fire Trouble will stop relay action. 05 = Trouble Day/Alarm Night 10 = Interior w/Delay Choices for System Operation are: 20 = ArmingÐStay 33 = Any Burglary Alarm 39 = Any Fire Alarm 21 = ArmingÐAway 34 = Code + # + 7 Key Entry 40 = Bypassing 22 = Disarming (Code + OFF) 35 = Code + # + 8 Key Entry 41 = AC Power Failure 31 = End of Exit Time 36 = At Bell Timeout** 42 = System Battery Low 32 = Start of Entry Time 38 = Chime 58 = Duress **Or at Disarming, whichever occurs earlier. ZONE LISTS FOR OUTPUT RELAYS Record desired zone numbers. More or fewer boxes than shown may be needed, since any list may include any or all of system's zone numbers. Zone List 1: Started or stopped by zone numbers (enter 00 to end entries). , , , , , , , , , ...etc. , , ...etc. , , ...etc. Zone List 2: Started or stopped by zone numbers (enter 00 to end entries). , , , , , , , Zone List 3: Started or stopped by zone numbers (enter 00 to end entries). , , , , , , –6– , MECHANICS OF PROGRAMMING This section provides information on how programming is performed in this system. It will enable you to understand how to enter and exit the programming mode, and how to program the data fields and the user-friendly interactive menu modes ( ✱56, ✱ 80, ✱ 81, ✱ 82, ✱ 83). We therefore urge you to read and understand the following before proceeding with any programming. The following program fields must be programmed (as required) before doing any programming. ✱ 22. RF SYSTEM ✱ 25. OUTPUT RELAY MODULE See Programming System Setup Fields on next page. General Programming Information Characteristics for each installation are stored in non-removable, electrically erasable, non-volatile EEROM memory. These must be programmed for the particular instal lation to establish its specific alarm and reporting features. It is possible to program the system at any time, even at the installer's premises prior to the actual installation. Simply apply power temporarily to the control and then program the unit as desired. Note: You cannot enter the programming mode unless the system is disarmed. There are two programming modes: data field programming and interactive menu mode programming. Data field programming is used for setting various system options and menu mode programming is used for programming zone information, programming relay outputs, and for entering 5800 series transmitter serial numbers. To program the system, you must use an FA550KP 2-line Alpha keypad connected to the keypad terminals on the control (4, 5, 6, & 7). The Alpha keypad need not necessarily remain in the system after programming. Programming can also be performed remotely from the installerÕs office/home, using an IBM personal computer, a modem, and appropriate downloading software. See the REMOTE PROGRAMMING AND CONTROL (DOWNLOADING) section in this manual. Entering the Program Mode You may use one of the following methods: (a) Press both the [ ✱] and [#] keys at the same time within 50 seconds after power is applied to the Control, or (b) After power up, enter the INSTALLER code (4 1 1 1) + 8 + 0. Method (b) is disabled if you exit the program mode using ✱ 98 instead of ✱99. See ÒExiting the Program ModeÓ paragraph later in this section. If a different INSTALLER code is subsequently pro grammed, use it instead of 4111 to gain access to the Programming mode. Following entry into the program mode, data field ✱20 will be dis played (this is the first field in the system). The system will now accept en tries for field ✱ 20. You can then proceed with the required programming (see the next paragraph ÒProgramminng a Data FieldÓ). Programming a Data Field 1. Press [ ✱] plus Field No. (for example, ✱21), then make the desired entry. 2. When you have completely programmed a data field, the keypad will ÒbeepÓ three times and then automatically display the next data field in sequence. To go to a different field, press [✱] plus the desired field No. –7– 3. If the number of digits that you need to enter in a data field is less than the maximum digits available (for ex ample, the phone number field), enter the desired data, then press ✱ and the next data field number to be programmed. 4. If you try to enter a non-existent field, an Alpha keypad will display NOT USED and EE (Entry Error). Simply key [✱ ] again plus a valid field number. Reviewing a Data Field/Erasing an Entry in a Data Field Press [#] plus Field No. Data will be displayed for that field number. N o changes will be accepted in this mode. To delete an entry in a field, press [ ✱] plus Field No. + [✱]. ( Applies only to fields ✱40 Ð ✱ 42, and ✱94.) Interactive Menu Mode Programming ( ✱56, Typical prompt displayed during interactive menu mode programming Enter Zn Num. (00 = Quit) 01 ÊZone Number ↑ ✱80, ✱81, ✱82 and ✱83) Press [ ✱] plus menu mode No. (for example, ✱ 56). The Alpha keypad will display the first of a series of prompts requesting entries. A detailed procedure (with displays of prompts) is provided in those sections in the Installation Instructions where programming in the menu mode is to be performed. Menu Mode ✱56 Zone Programming ✱80 ✱81 ✱82 ✱83 Used To Program Zone characteristics, report codes, alpha descrip tors and serial numbers for 5800 transmitters Relay Programming 4204 Relay modules Zone List Programming Zone Lists for 4204 relay activation Alpha Programming Zone alpha descriptors Sequential Mode 5800 series transmitter serial numbers Loading Factory Defaults ( ✱97) To load the factory defaults, enter the programming mode, press the programming mode. ✱ 97, then exit Do not press ✱ 97 to load defaults if any programming has been done previouslyÑdata already programmed into the system will be changed! ✱96 resets the Subscriber Account number and CSID in preparation for an initial download. Programming System Setup Fields The following program fields MUST be programmed before doing any programming. ✱22 RF SYSTEMÊÊÊ(Default is 0). Enter Ò1Ó if 5700 RF system type is being used; enter Ò2Ó if a 5800 RF system type is being used; enter Ò0Ó if no RF is being used. ✱25 WIRED EXPANSION/OUTPUT RELAYÊÊ(Default is 0). Enter Ò1Ó if a 4219 wired expansion unit is used, Ò2Ó if a 4229 wired expansion/ relay unit is used, Ò3Ó if a 4204 relay is being used, or Ò0Ó if none are being used. Exiting the Programming Mode ✱98 EXITS PROGRAMMING MODE and prevents re-entry by Installer Code + [Code] + [0] . To enter the programming mode if ✱98 was used to exit, you must first power the system down. Then power up again, and press [ ✱] and [#] both at once, within 50 seconds of powering up. ✱99 EXITS PROGRAMMING MODE and allows re-entry by: Installer Code + [Code] + [0] or by: Pressing [ ✱] and [#] at the same time, within 50 seconds of powering up the system. –8– 5800 Series Transmitter Input Loop Identification ¥ All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes. Each of the inputs requires its own programming zone (e.g., a 5804's four inputs require four programming zones). ¥ Transmitter inputs entered as: "RF" (Supervised RF) Type send periodic check-in signals, as well as fault, restore and low battery signals. The transmitter must remain within the receiver's range. ÒUR" (Unsupervised RF) Type send all the signals that the "RF" Type does, but the control does not supervise the check-in signals. The transmitter may, therefore, be carried off-premises. "BR" (Unsupervised Button RF) Type only send fault signals. Restore or check-in signals are not sent, but low battery signals are sent when a button is pressed. The transmitter may be car ried offpremises. The transmitter may be carried off-premises. INPUT (LOOP) 3 2 1 INPUT (LOOP) 1 4 (PRIMARY) (REED) LOOP 1 (TERMINALS) (AUX. CENTER) 3 (AUX. RIGHT) 5802MN LEARN AS "UR" OR "RF" INPUT (LOOP) 2 LOOP 3 LOOP 2 LOOP 3 (TERMINALS) 5817 LEARN AS "RF" 5801 LEARN AS "UR" OR "RF" 5827 SET HOUSE ID (DIP SWITCHES) 5819 LEARN AS "RF" 5827 SET HOUSE CODE (REED) INPUT (LOOP) 1 LOOP 1 LOOP 1 (INTERNAL SHOCK 5827BD SENSOR) 5808 LEARN AS "RF" 5804 LEARN AS "BR" INPUT (LOOP) 2 2 (ALWAYS USE) YOU MUST LEARN THIS BUTTON LOOP 4 INPUT (LOOP) 1 SET HOUSE ID 5827BD SET HOUSE CODE LOOP 3(KEYPAD PROGRAMMABLE) (TERMINALS) 5819S (WHS & BRS) LEARN AS "RF" INPUT (LOOP) 2 (REED) INPUT (LOOP) 2 (REED) INPUT (LOOP) 1 LOOP 1 (TERMINALS) LOOP 1 (TERMINALS) (MOTION) (Green) (Red) (Yellow) 5816 LEARN AS "RF" ALTERNATE POSITION FOR LOOP2 5816MN LEARN AS "RF" 5850 (GBD) LEARN AS "RF" –9– 5890 LEARN AS "RF" ALPHA VOCABULARY LIST (For Entering Zone Descriptors) NOTE : Some rarely-used words appearing in previously published lists have been deleted from the list below. Use only this list for selecting zone descriptors. 000 ¥ 001 ¥ 002 004 005 ¥ 006 ¥ 007 ¥ 009 010 ¥ ¥ ¥ ¥ ¥ ¥ ¥ 012 013 014 016 017 018 019 020 ¥ 021 ¥ 022 023 025 ¥ 026 028 029 030 031 033 034 035 036 037 038 040 046 047 ¥ ¥ ¥ ¥ ¥ 048 049 ¥ 050 051 ¥ 052 ¥ 053 054 055 Note: (Word Space) A AIR ALARM ALLEY AMBUSH AREA APARTMENT ATTIC AUDIO B BABY BACK BAR BASEMENT BATHROOM BED BEDROOM BELL BLOWER BOILER BOTTOM BREAK BUILDING C CABINET CALL CAMERA CAR CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLOSED COMPUTER CONTACT D DAUGHTERS DELAYED DEN DESK DETECTOR DINING DISCRIMINATOR DISPLAY ¥ 057 ¥ 059 ¥ 060 061 ¥ 062 ¥ 064 ¥ 065 066 067 068 ¥ 069 ¥ 071 072 ¥ 073 075 ¥ 076 ¥ 077 ¥ 079 ¥ 080 081 082 ¥ 083 084 ¥ 085 ¥ 089 ¥ 090 091 ¥ 092 093 094 ¥ 095 ¥ 096 098 099 100 ¥ 101 102 103 104 ¥ 105 DOOR DOWN DOWNSTAIRS DRAWER DRIVEWAY DUCT E EAST ELECTRIC EMERGENCY ENTRY EQUIPMENT EXIT EXTERIOR F FACTORY FAMILY FATHERS FENCE FIRE FLOOR FLOW FOIL FOYER FREEZER FRONT G GARAGE GAS GATE GLASS GUEST GUN H HALL HEAT HOLDUP HOUSE INFRARED INSIDE INTERIOR INTRUSION J JEWELRY K KITCHEN ¥ 106 ¥ 107 108 ¥ 109 ¥ 110 111 ¥ 113 ¥ 114 115 116 117 ¥ 118 ¥ 119 121 122 ¥ 123 ¥ 125 126 128 129 ¥ 130 ¥ 131 132 ¥ 134 135 ¥ 136 ¥ 138 139 ¥ 140 142 ¥ ¥ ¥ ¥ 143 144 145 146 147 148 150 151 152 153 155 ¥ 156 L LAUNDRY LEFT LEVEL LIBRARY LIGHT LINE LIVING LOADING LOCK LOOP LOW LOWER M MACHINE MAIDS MAIN MASTER MEDICAL MEDICINE MONEY MONITOR MOTHERS MOTION MOTOR N NORTH NURSERY O OFFICE OPEN OPENING OUTSIDE OVERHEAD P PAINTING PANIC PASSIVE PATIO PERIMETER PHONE POINT POLICE POOL POWER R RADIO REAR 155 ¥ 156 157 159 160 ¥ 161 ¥ 162 163 ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ 164 165 166 167 168 169 170 171 173 174 175 176 178 179 180 182 184 185 186 190 191 192 193 194 196 197 ¥ 199 200 ¥ 201 202 ¥ ¥ ¥ ¥ 205 206 207 208 R RADIO REAR RECREATION REFRIGERATION RF RIGHT ROOM ROOF S SAFE SCREEN SENSOR SERVICE SHED SHOCK SHOP SHORT SIDE SKYLIGHT SLIDING SMOKE SONS SOUTH SPRINKLER STATION STORE STORAGE STORY SUPERVISED SUPERVISION SWIMMING SWITCH T TAMPER TELCO TELEPHONE TEMPERATURE THERMOSTAT TOOL TRANSMITTER U UP UPPER UPSTAIRS UTILITY 209 210 212 213 214 ¥ 216 ¥ 217 ¥ 219 220 222 223 ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 V VALVE VAULT VOLTAGE W WALL WAREHOUSE WEST WINDOW WING WIRELESS X XMITTER Y YARD Z ZONE (No.) ZONE 0 1 1ST 2 2ND 3 3RD 4 4TH 5 5TH 6 6TH 7 7TH 8 8TH 9 9TH 250 Custom Word #1 251 Custom Word #2 252 Custom Word #3 253 Custom Word #4 254 Custom Word #5 Bulleted (¥) words in boldface type are those that are also available for use by the 4285 Phone Module. If using a Phone module, and words other than these are selected for Alpha descriptors, the module will not provide annunciation of those words. CHARACTER (ASCII) CHART (For Adding Custom Words) 32 (space) 33 ! 34 " 35 # 36 $ 37 % 38 & 39 ' 40 ( 41 ) 42 43 44 45 46 47 48 49 50 51 ✴ + , Ð . / 0 1 2 3 52 53 54 55 56 57 58 59 60 61 4 5 6 7 8 9 : ; < = 62 63 64 65 66 67 68 69 70 71 ÊÊ – 10 – > ? @ A B C D E F G 72 73 74 75 76 77 78 79 80 81 H I J K L M N O P Q 82 83 84 85 86 87 88 89 90 R S T U V W Y Z ZONE RESPONSE TYPE DEFINITIONS Type 00 Zone Not Used Type 01 Entry/Exit Burglary Type 02 Program a zone with this zone type if the zone is not used. This zone type provides entry delay whenever the zone is faulted if the control is armed in the AWAY or STAY modes. When the panel is armed in the Instant or Maximum modes, no entry delay is provided. Exit delay begins whenever the control is armed, regardless of the arming mode selected. These delays are programmable. This zone type is usually assigned to sensors or contacts on doors through which primary entry and exit will take place. Not used in this system Type 03 Perimeter Burglary This zone type gives an instant alarm if the zone is faulted when the panel is armed in the AWAY, STAY, INSTANT or MAXIMUM modes. This zone type is usually assigned to all sensors or contacts on exterior doors and windows. Type 04 Interior, Follower This zone type is active when the panel is armed in the AWAY or MAXIMUM modes. Entry delay (using the programmed entry time) results if the panel is armed in the AWAY mode and the entry/exit zone is faulted first. Otherwise this zone type gives an instant alarm. Exit delay is present for any arming mode. This zone type is usually assigned to a zone covering an area such as a foyer, lobby, or hallway through which one must pass (upon entry, after faulting the entry/exit zone) to reach the keypad to disarm the system. Since this zone type is designed to pro vide an instant alarm if the entry/exit zone is not violated first, it will protect an area in the event an intruder hides on the premises prior to the system being armed, or gains access to the premises through an unprotected area. This zone type is bypassed automatically when the panel is armed STAY or INSTANT. Type 05 Trouble by Day/ Alarm by Night This zone type will give an instant alarm if faulted when armed in the AWAY, STAY, INSTANT or MAXIMUM (night) modes. During the disarmed state (day), the system will provide a latched trouble sounding from the keypad (and a central station report, if desired). This zone type is usually assigned to a zone which contains a foil-protected door or window (such as in a store), or to a zone covering a "sensitive" area such as a stock room, drug supply room, etc. This zone type can also be used on a sensor or contact in an area where immediate notification of an entry is desired. Type 06 24-hour Silent Alarm This zone type sends a report to the Central Station but provides no keypad display or sounding. This zone type is usually assigned to a zone containing an Emergency button. Type 07 24-hour Audible Alarm This zone type sends a report to the Central Station, and provides a rapid beeping sound at the keypad, and an audible external alarm. This zone type is usually assigned to a zone that has an Emergency button. Type 08 24-hour Auxiliary Alarm This zone type sends a report to the Central Station and provides a rapid beeping sound at the keypad. (No bell output is provided). This zone type is usually assigned to a zone containing a button for use in personal emergencies, or to a zone containing monitoring devices such as water or temperature sensors, etc. Type 09 Supervised Fire This zone type provides a fire alarm on short circuit and a trouble condition on open circuit. The bell output will pulse when this zone type is faulted. This zone type is always active and cannot be bypassed. This zone type can be assigned to control panel wired zone 5 and to certain wireless zones. Type 10 Interior w/Delay This zone type gives entry delay (using the programmed entry time), if tripped when the panel is armed in the Away mode, regardless of whether or not an entry/exit delay zone was tripped first. This zone type is also active during MAXIMUM mode, but n o entry delay is provided (an alarm occurs immediately if the zone is tripped). Exit delay is present for any arming mode. This zone type is bypassed automatically when the panel is armed Stay or Instant . – 11 – Type 20 ArmÐStay This is a special-purpose zone type used with 5800 series wireless pushbutton units which will result in arming the system in the STAY mode when the zone is activated. Pushbutton units send zone number as a user number to central station when arming or disarming. Type 21 ArmÐAway This is a special-purpose zone type used with 5800 series wireless pushbutton units which will result in arming the system in the AWAY mode when the zone is activated. Pushbutton units send zone number as a user number to central station when arming or disarming. Type 22 Disarm This is a special-purpose zone type used with 5800 series wireless pushbutton which will result in disarming the system when the zone is activated. Type 23 No Alarm Response This can be used on a zone when an output relay action is desired, but with no accompanying alarm (e.g., lobby door access). By using a 4281/5881 type RF Receiver and the appropriate 5700/5800 series transmitters, all of the zone types listed* are available for the wireless portion of the system. * Note: Zone Types 20, 21, and 22 cannot be used in a 5700 RF system. – 12 – DATA FIELD DESCRIPTIONS The blank programming form in this manual should be used to record the data for this installation. The following is a list of all data fields in this control (presented in numerical order). This list provides an explanation of each data field, and will serve as a reference for all fields in the system. Defaults (where applicable) are indicated in the text for each field in this list. Note:ÊThe Radio should be programmed for device address 3 on the keypad lines. ✱20 INSTALLER CODE Default is 4-1-1-1. The Installer code is used to program the system, and to assign the 4-digit Master security code in the normal operation mode, via the keypad See "Master Code" in the SYSTEM OPERATION section in the Installation Instructions for the procedure. Enter 4 digits, 0Ð9. ✱21 QUICK ARM ENABLE (1-Digit Entry) Default is 0. If enabled, the [#] key can be used instead of the security code when arming the system. Enter 0 for disabled or 1 for enabled. This feature will function only if the Master Code is programmed. ✱22 RF SYSTEM (1-Digit Entry) Default is 0 (none). This option is enabled if a wireless receiver is used. Enter 1 for 4281 series RF receivers, 2 for 5881* series RF receivers. Enter 0 if no receiver is being used. * 5882 series RF receivers in Canada. ✱23 FORCED BYPASS FUNCTION (1-Digit Entry) Default is 0. This feature allows all open zones to be bypassed automatically. Ò1Ó will bypass all open zones, Ò2Ó will bypass all open zones, plus zones 17, 30, 31, 46, and 47 (whether open or not) All zones that are bypassed by this function will be displayed after the bypass is initiated: ✱24 RF HOUSE ID CODE (2-Digit Entry) Default is 00 . The House ID identifies receivers and wireless keypads in a 5700 type system, and must be assigned (01Ð31). If a 5827 or 5827BD Wireless keypad is to be used in a 5800 RF system, a House ID code MUST also be entered (01Ð31), and the keypad should be set to the same ID. In a 5800 system with no 5827 or 5827BD wireless keypad, enter 00 (no House ID). ✱25 WIRED EXPANSION/OUTPUT RELAY USEDÊÊÊÊ (1-Digit Entry) Enter Ò1Ó if a 4219 wired expansion unit is used, Ò2Ó if a 4229 wired expansion/ relay unit is used, Ò3Ó if a 4204 relay is being used, or Ò0Ó if none are being used (Ò0Ó is the default). ✱26 VOICE (PHONE) MODULE ACCESS CODE (2-Digit Entry) Default is 00 . The use of a 4285 Phone Module requires a 2-digit phone access code. Enter as follows: ÊFor first digit, enter any digit from 1 to 9; for second digit, enter # +11 for " ✱ ", or # +12 for "#". Example: If the desired access code is 7 ✱ , 7 is the first entry, and # + 11 (for ✱ ) is the second entry. Ò00Ó = Phone Module disabled. Note: A Ò0Ó in either digit will disable the 4285 Phone Module. ✱27 OUTPUT TO LONG RANGE RADIO (1-Digit Entry) Default is 0. 0= no, 1 = yes. If output to LRR is selected here (1), all messages that are programmed to go to the primary telephone line receiver will also be sent to the radio (e.g., 7720 PLUS or 7820). These messages will always be in Contact ID format (overriding the selection in field ✱46). The data line is supervised ,as well as certain functions in the radio. If communication is lost or a trouble develops, a message will be attempted to be sent via both radio and telephone to the central station. Normal trouble restore report ( ✱71) is sent on restore of the condition. – 13 – ZONE SOUNDS AND TIMING (✱28Ð✱ 39) ✱28 UL SINGLE ALARM SOUNDING PER ZONE Default is 0. (Per Armed Period) (1-Digit Entry) This field limits external alarm sounding to once per arming period for a given zone. Enter 1 for yes; 0 for no. For UL installations, enter 0 for unlimited Alarm Soundings ✱29 FIRE SOUNDER TIMEOUT (1-Digit Entry) Default is 0. This field determines whether the external sounder will shut off after time allotted, or continue until manually turned off. Enter 0 for sounder timeout, or 1 for no timeout. ✱30 ALARM BELL TIMEOUT (1-Digit Entry) Default is 1. This field determines whether the external sounder will shut off after time allotted, or continue until manually turned off. Enter as follows: 0 = No timeout; 1 = 4 min (default); 2 = 8 min; 3 = 12 min; 4 = 16 min. ✱38 ENTRY DELAY (1-Digit Entry) Default is 2. System will wait the time allotted before sounding alarm upon entering. May be selected individually 0 = 0 secs; 1 = 20 secs; 2 = 30 secs; 3 = 45 secs; 4 = 60 secs; 5 = 90 secs. (EXIT delay = Entry delay plus 15 seconds). UL For UL installations, entry delay can be no greater than 45 seconds. ✱39 AUDIBLE EXIT WARNING (1-Digit Entry) Default is 1. If enabled, this field provides exit warning sound when armed AWAY or MAXIMUM. Warning sound consists of slow continuous beeps until last 5 seconds, when it changes to fast beeps. The warning sound will end at the termination of Exit time. 0 = no; 1 = yes. DIALER PROGRAMMING (✱40Ð✱ 50) ✱40 Fields ✱40, ✱ 41, ✱ 42: Enter up to the number of digits shown. Do not fill unused spaces. Enter 0Ð9, # + 11 for Ô ✱Õ # + 12 for Ô#Õ # + 13 for a pause (2.5 secs) PABX ACCESS CODE (See Box at Left) Enter up to 4 digits if PABX is needed to access an outside line. If fewer than 4 digits are needed to be entered, exit by pressing ✱ and next field number (e.g., 41). To clear entries from field, press ✱ 40✱ . ✱41 PRIMARY PHONE No. (See Box at Left) Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing ✱ and next field number (e.g., 42). To clear entries from field, press ✱41✱ . Note: Back-up reporting (8 calls are made to the secondary phone number if no kiss-off is received after 8 attempts to primary number) is automatic only if there is a secondary phone number (field ✱ 42). ✱42 SECONDARY PHONE No. (See Box at Left) Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing ✱ and next field number (e.g., 43). To clear entries from field, press ✱42✱ . See Note in field ✱ 41 also. Note: If you wish to send a report to a pager, see field ✱47 on next page . ✱43 SUBSCRIBER ACCOUNT. No. (Enter 4 digits). Enter digits 0Ð9, #+11=B, #+12=C, #+13=D, #+14=E, or #+15=F. See the Programming Form for examples. Enter 0 as the first digit of a 4-digit account No. Note: Do not enter Ò0Ó as the first digit if you intend to use the Paging feature (see selections 6Ð9 in field ✱47). Some paging systems have voice mail capability, activated by a leading Ò0Ó in the message. End field by pressing ✱ (and press next field). This field is also used as the Long Range Radio Subscriber Account #. – 14 – ✱45 PHONE SYSTEM SELECT (1-Digit Entry) If Central Station Receiver is not on WATS line: 0 = Pulse Dial 1 = Tone Dial If Central Station Receiver is on WATS line: 2 = Pulse Dial 3 = Tone Dial ✱46 REPORT FORMAT (1-Digit Entry) Default is 0. Determine which format is to be used to report to the central station. Enter 1 digit (0Ð9). 0 = 3+1; 4+1 ADEMCO Lo Speed Standard (this is the default) 1 = 3+1; 4+1 Radionics Standard 2 = 4+2 ADEMCO Lo Speed Standard 3 = 4+2 Radionics Standard 6 = 4+2 ADEMCO Express 7 = ADEMCO Contact ID Reporting 8 = 3+1; 4+1 ADEMCO Lo Speed Expanded 9 = 3+1; 4+1 Radionics Expanded (Enter ✱ as the 4th digit of ✱ 43 if 3+1 dialer reporting is to be used.) Note: The maximum number of alarm and alarm restore reports during one armed period is determined by field ✱ 92. See field ✱ 27, which may override this fieldÕs selection. ✱47 SPLIT/DUAL REPORTING (1-Digit Entry) Default is 0. Enter 0 to disable (Backup report only). Entries 1 through 9 can be made, as indicated in the table below. Entries 6 through 9 will send a report to a pager (in addition to the selected primary phone number), but you must enter the pager number as the secondary phone number in field ✱42. For an explanation of these formats, see the SYSTEM COMMUNICATION section in the Installation Instructions. Ê* Can only be used if the Primary reporting format is Ademco Contact ID. If reporting to a Pager, choose from 6, 7, 8, or 9, as desired. Default is 0. Ê1 = Ê2 = Ê3 = Ê4 = Ê5 = TO PRIMARY PHONE # Alarms, Restore, Cancel All except Open/Close, Test Alarms, Restore, Cancel All except Open/Close, Test All reports TO SECONDARY PHONE # Other Reports Open/Close, Test All reports All reports All reports Ê6 = Ê7 = Ê8 = Ê9 = TO PRIMARY PHONE # All reports except Open/Close All reports All reports All reports except Open/Close TO PAGING No. * (Secondary) Alarms/Open/Close, Troubles Alarms, Troubles Alarms/Open/Close, Troubles Alarms, Open/Close for users #5Ð25à, Troubles à Will report only Users 5, 6 & 8. If using 5800 series wireless button-type devices, the zone number of the arm or disarm button (10Ð25) will be sent as the user number. Entries 6 through 9 will send a report to a pager (in addition to the selected primary phone number), but you must enter the pager number as the secondary phone number in field ✱42. A 10-digit code is sent to the pager which will take the following format: 4-digit Subscriber No . → Ê SSSSÐEEEÐNNN ← 3-digit User or Zone No. (as entered in field ✱ 43) Ê ↑ 3-Digit Event Code (EEE), as follows: 911 = Alarm (NNN = Zone No.) 001 = Open, System disarmed (NNN = User No.) 002 = Close, System armed ( NNN = User No.) 811 = Trouble ( NNN = Zone No.) Ê The first digit of the Subscriber No. entered in field ✱43 must be 1Ð9 (do not use 0); the ÊÊÊlast 3 digits can be 0Ð9. Failure to observe this requirement may interfere with ÊÊÊpaging services. (Continued) – 15 – Example 1.ÊÊ Pager displays:ÊÊ1 23 4Ð911Ð004 This indicates that Subscriber No. 1234Õs system is reporting an Alarm (911), due to zone 4 being faulted (004). Example 2.ÊÊPager displays:ÊÊ1 23 4Ð001Ð005 This indicates that Subscriber No. 1234Õs system is reporting an opening (001) by User 5 (005). Note that no restore reports are sent to the pager. Important: AAV should not be used when Paging or Alarm Reports are being sent to a Secondary number. If this is done, the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the telephone line, and the AAV ÒListen inÓ session cannot then take place. ✱48 15-SECOND DIALER DELAY (BURGLARY) Default is 0 . Single-digit entry. If selected, will provide 15-second delay of burglary alarm report to the central station. Allows time for subscriber to avoid a false alarm transmission. 0 for no delay, or 1 for 15-second delay. ✱49 PERIODIC TEST REPORT (1-Digit Entry) Default is 0. Select the desired test report interval. 0 = none; 1 = 24 hours; 2 = weekly; 3 = 30 days. Test Report code entered in field ✱ 64 is sent; reports with Subscriber No. UL For UL installations, 24 hours (1) must be selected ✱50 SESCOA/RADIONICS SELECT 0 = Radionics (0Ð9, BÐF reporting) 1 = SESCOA (0Ð9 only reporting) Select 0 for all other formats. ✱51 CONFIRMATION OF ARMING DING (1-Digit Entry) Default is 0. Enter 1 to enable 1/2 second external alarm sounding ÒdingÓ when closing report goes in, or at the end of exit delay. Enter 2 for alarm sounding ding with RF arming only (this will work with either a button RF unit or a 5827. 0 disables the ÒdingÓ. ✱52 ZONE 3 RESPONSE TIME TO OPEN (1-Digit Entry) 0 = 400ms nominal; 1 = 10ms nominal. ✱56 (1-Digit Entry) Default is 0. Default is 0. ÊÊ ZONE ASSIGNMENT/ALARM REPORT CODES This is an interactive menu mode that is used to program z o n e numbers, zone types, alarm and report codes, and to identify the type of loop input device. This mode can also be used for entering 5800 series transmitter serial numbers (serial numbers can also be entered using the Sequential Mode in ✱83, but only after all other zone programming has been completed in ✱56). Alpha descriptors can also be entered for zones in ✱56 (alternatively, Alpha descriptors can be entered in menu mode ✱82). Refer to the BASIC HARDWIRED ZONES 1Ð6 section in the Installation Instructions for detailed hardwired zone programming, and the WIRELESS (RF) ZONE EXPANSION (5700 & 5800 RF SYSTEMS ) section for detailed wireless zone expansion programming. Refer also to the zone assignment table for ✱ 56 in the programming form in this manual. – 16 – TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES (✱60 Ð ✱ 68, ✱70 Ð ✱ 75) SYSTEM STATUS REPORT CODES (✱60 Ð✱ 68) With a 3+1 or 4+1 Standard Format: Enter a code in the first digit box: 1Ð9, 0, B, C, D, E, or F. Enter "# + 10" for 0, "# + 11" for B, "# + 12" for C, "# + 13" for D, "# + 14" for E, "# + 15" for F. A "0" (not "# + 10") in the first digit box will disable a report. A "0" (not "# + 10") in the second digit box (if any) will result in automatic advance to the next field when programming. With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1Ð9, 0, or BÐF, as de scribed above. A "0" (not "# + 10") in the second box will eliminate the expanded message for that report. A "0" (not "# + 10") in both boxes will disable the report. With Ademco Contact ID Reporting: Enter any digit (other than "0") in the first box, to enable zone to report This is an "enabling" code only and is disregarded in the actual reporting to the central office. Entries in the second boxes will be ignored. A "0" (not "# + 10") in the first box will disable the report. Examples: For Code 3 (Single Digit), enter: ÊÊÊÊ3ÊÊÊÊ ÊÊÊÊ0ÊÊÊÊ For Code 32 (Two Digits), enter: ÊÊÊÊ3ÊÊÊÊ ÊÊÊÊ2ÊÊÊÊ For Code B2 (Hexadecimal) enter: #Ê+Ê11Ê ÊÊÊÊ2ÊÊÊÊ ✱60 TROUBLE REPORT CODEÊÊ (See box above.) (2-Digit Entry) ✱61 BYPASS REPORT CODEÊ (See box above.) (2-Digit Entry) ✱62 AC LOSS REPORT CODEÊ (See box above.) (2-Digit Entry) Reports with Subscriber No. Timing of this report is random with up to a 48-minute delay. The Restore report has a random delay of up to about 12 minutes. If AC restores before the report goes out, there is no AC restore report. ✱63 LOW BAT REPORT CODE (See box above.) Reports with Subscriber No. (2-Digit Entry) ✱64 TEST REPORT CODE (See box above.) Periodic Reports with Subscriber No. (2-Digit Entry) ✱65 OPEN/EXIT ALARM REPORT CODE, 1st DIGITS (2-Digit Entry) Open Report Code : To enable, enter a code (or 0 to disable) in the lefthand box (see box above). For expanded or 4+2 reporting, 2nd digit = User #. Exit Alarm Report Code: To enable, enter a code (or 0 to disable) in the right-hand box (see box above). If enabled, any alarm from an exit or interior zone occurring within two minutes after the end of the exit delay will send a special message indicating exit alarm to the central station, and a zone indication and "Exit Alarm" or "EA" is displayed on the keypad. If an exit or interior zone contains a fault as the exit delay ends, the local bell and keypad sound continuously. a) If the subscriber then disarms the system before the ensuing Entry delay ends, no message is transmitted to the central station, but a zone indication and "Canceled Alarm" or "CA" is displayed on the keypad. b) If the system is not disarmed before that entry delay ends , a special message indicating Exit Alarm is sent to the central station and a zone indication and "Exit Alarm" or "EA" is displayed on the keypad. For expanded or 4+2 reporting, a 2nd digit is sent, and is the same as the 2nd digit of the zone alarm report code programmed in field ✱56. For Contact ID reporting, Event code 374 and the zone number is sent. There is no restore message for an Exit Alarm report. – 17 – RESTORE REPORT CODES (✱70 Ð ✱ 75) ✱66 AWAY/STAY CLOSE REPORT CODE (2-Digit Entry) (See box on previous page.) To enable, enter a code (or 0 to disable) in either or both boxes. For expanded or 4+2 reporting, 2nd digit for each = User # . ✱67 RF XMTR. LOW BATTERY REPORT CODE (See box on previous page). ✱68 CANCEL REPORT CODE (2-Digit Entry) (See box on previous page.) ✱70 ALARM RESTORE REPORT CODE (See box on previous page). For expanded or 4+2 reporting, a 2nd digit is automatically sent, and is the same as the 2nd digit of the zone alarm report code programmed in field ✱ 56. ✱71 TROUBLE RESTORE REPORT CODE (2-Digit Entry) (See box on previous page). This is sent when a trouble in a zone is restored. ✱72 BYPASS RESTORE REPORT CODE (2-Digit Entry) (See box on previous page) . This is sent when a zone that has been bypassed is un-bypassed. ✱73 AC RESTORE REPORT CODE (2-Digit Entry) (See box on previous page) . Reports with Subscriber No. ✱74 LOW BAT RESTORE REPORT CODE (2-Digit Entry) (See box on previous page). Reports with Subscriber No. ✱75 RF XMTR. LOW BATTERY RESTORE CODE (2-Digit Entry) (See box on previous page). This is sent when a transmitter that previously sent in a low battery message has sent a message indicating it no longer has a low battery condition. ✱80 OUTPUT RELAYS This is an interactive menu mode that is applicable only if a 4229 wired expansion/relay unit or 4204 relays are to be used (Ò2Ó and Ò3Ó respectively in field ✱ 25). See the RELAY OUTPUTS section in the Installation Instructions for a detailed programming procedure. Also refer to the OUTPUT RELAY table for field ✱80 in the Programming Form in this manual. ✱81 ZONE LISTS FOR OUTPUT DEVICES This is an interactive menu mode that is applicable only if field ✱ 25 is programmed for 4229 or 4204 relays. Refer to the RELAY OUTPUTS section in the Installation Instructions for a detailed programming procedure. Also refer to the ZONE LISTS FOR OUTPUT RELAYS table for ✱81 in the Programming Form in this manual. ✱82 CUSTOM ALPHA EDITING See the ALPHA DESCRIPTION PROGRAMMING section in the Installation Instructions for procedure. ✱83 SEQUENTIAL MODE May be used for enrolling transmitters in a 5800 RF system after all other zone information has been programmed in ✱56. See the Installation Instructions for a detailed programming procedure. ✱91 CUSTOM OPTION SELECTION (1-Digit Entry) Default is 0. Select one of the following 0 = None selected 5 = Local lockout + AAV 1 = Local lockout 6 = Sounder delay + AAV 2 = Sounder delay 7 = Local lockout + Sounder delay ÊÊÊÊÊ+ AAV 3 = Local lockout + Sounder delay 4 = AAV (Audio Alarm Verification) Local lockout: Exiting by ✱98 will allow re-entry into programming mode at the keypad only by:ÊÊInstaller Code + 8 + 0 (not by: Power-up + [✱] & [#]). – 18 – (2-Digit Entry) Sounder delay: Delays the external sounder by 15 seconds for Fire and Burglary. Internal sounder is immediate on alarm. Communicator (dialer) delay is still set by field ✱ 48. AAV (Audio Alarm Verification): Cuts off internal and external sounders for that alarm at termination of communicator report of alarm, and causes Output Relay 01 to energize for 2 seconds to trigger AAV Unit. UL For UL installations, the AAV option cannot be used (do not select 4, 5, 6, or 7). AAV should not be used when Paging or Alarm Reports are being sent to a Secondary number. If this is done, the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the telephone line, and the AAV ÒListen inÓ session cannot take place. ✱92 NUMBER OF REPORTS IN ARMED PERIOD Default is 0. (1-Digit Entry). This option can be used to limit the number of messages (alarm & alarm restore reports) sent to the central station in an armed period. Ò0Ó limits reports to a total of 10; Ò1Ó allows an unlimited number of reports. UL DOWNLOAD INFORMATION (✱94, ✱ 95) Ò1Ó must be selected for UL installations ✱94 DOWNLOAD PHONE NUMBER Enter up to 12 digits; 0Ð9, # +11 for Ò✱ Ó, # + 12 for Ò#Ó, # + 13 for a pause. Do not fill unused spaces. If fewer than 12 digitsare entered, exit field by entering ✱ (and press 95 if entering next field) . To clear entries from field, press ✱ 94✱ . ✱95 RING DETECTION COUNT FOR DOWNLOADING Default is 0. Enter number of rings before control picks up phone line (or 0 or 15). Refer to the chart below and program this field accordingly. ÊPhone Module Yes Answering ÊÊMachine No Yes Yes Yes Yes No No No No No Yes No Yes No Yes Downloading Field ✱95 No Set for value other than Ò0Ó (1Ð14). This will enable the control panel to answer the phone call. Otherwise, it will not be possible to access the Phone Module No Set for a value higher than the number of rings for which the answering machine is set. Example: if machine is set for 4 rings, use a value of 5 or higher. This is recommended so that the Phone Module can still be accessed if the answering machine is turned off and does not answer the phone call. Yes Set for value other than Ò0Ó (1Ð14). Yes Enter Ò15Ó to bypass answering machine. No Enter Ò0Ó. No Enter Ò0Ó. Yes Enter 1Ð14. Yes Enter 15. See Important Note below. Important Note: If Ò15Ó is entered in field ✱95 to bypass an answering machine, and a 4285 Phone Module is included in the installation, you should note the following: When calling in from an off-premises phone (to receive a status report or to execute a command), the user should make the initial call, allow 1 to 3 rings only, and hang up. Then call in again Ð the Phone Module will now seize the line, and 2 long tones will be heard, followed by the usual voice prompt for the 2-digit phone access code. If this procedure is not followed, Phone Module operation will not be possible. – 19 – TO EXIT PROGRAMMING MODE (✱98 or ✱99) ✱96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No. FOR DOWNLOADING (No data entry required; press ✱96) ✱97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES (No data entry required; pressing ✱ 97 automatically loads all First Alert defaults). Do not use if previously programmed with other values. ✱98 EXITS PROGRAMMING MODE and prevents re-entry by : INSTALLER Code + 8 + 0 . To enter the programming mode if ✱98 was used to exit, you must first power the system down. Then power up again, and depress [✱ ] and [#] both at once, within 50 seconds of powering up. ✱99 EXITS PROGRAMMING MODE and allows re-entry by: INSTALLER Code + 8 + 0 or by method described in paragraph above (power down, power up and depress [ ✱] and [#] both at once, within 50 seconds of powering up.) . – 20 – REMOTE PROGRAMMING AND CONTROL (DOWNLOADING) General Information The FA142C can be remotely programmed from an IBM compatible Per sonal Computer (PC), a HAYES Modem, and Downloading Software (as specified below). Programming the control from a remote location is protected against compromise by someone attempting to defeat the system, using multi-levels of security protection: 1. Security Code Handshake: An 8-digit download ID code must be matched between the control and the downloader. UL 2. Site-Initiated Remote Programming: Telco Hand-off feature allows the technician at the site to call the downloading facility from the control panel phone line, initiate a site download (Installer or Master Code + # + 1), and the control will immediately be on-line with the modem at the downloading facility. Also, if a local computer has a modem, the telephone line terminals of the control can be connected to the modem, and a direct download connection can be established with the new downloader program. 3. Station-Initiated Remote Programming: The operator calls the site from your office to initiate the download call. The control hangs up and then calls back the PC via the preprogrammed telephone number. The unit can then be uploaded, downloaded, or controlled from your office. The control can also be set for no callback by the downloader. 4. Data Encryption: Data passed between the PC and the control is en crypted for security so that it is very difficult for a foreign device tapped into the phone line to take over communication and substitute system compromising information. Downloading is not permissible for UL installations unless an installer is present at the installation site. Equipment Required At the premises: • FA142C Control and keypad. At the installer's of fice/home: • An IBM PC compatible computer. • Either a HAYES brand SMARTMODEM 1200 [Level 1.2 or higher external or Level 1.1 or higher (with 4 position DIP switch) internal style],or a HAYES brand Optima 24 Plus FAX96 Modem. • First Alert’s FADL Downloading Software (Rev 4 or higher), or Compass Windows downloading software (at revision level 1.0.1.0. or higher). • Appropriate interconnecting cables. Remote Programming Information The downloading system can perform many functions when in communication with the control unit. Besides uploading and downloading, the status of the sys tem can be observed and various commands can be initiated, as follows: • Arm the System in the Away Mode; Disarm the System. • Bypass a Zone. • Shut Down Communication (dialer) Functions (non-payment of monitoring fees in an owned system). • Shut Down all Security System Functions (non-payment for a leased system). – 21 – • Inhibit Local Keypad Programming (prevents account takeover). • Read: Arming Status, AC Power Status, Lists of Faulted Zones, Bypassed Zones, Zones Currently in Alarm, Zones Currently in Trouble, and RF Sensors with Low Battery Conditions. Note: After the control and the PC have established valid communication, each keypad on the system will become inactive and will display "CC" or " MODEM COMM.". The control, however, will still be scanning its zones and looking for alarms. If an alarm does occur, after communication is broken off, alarms are sounded and the proper dialer reports are sent to the central station. The keypads will become active after the download communication is terminated. The detailed operation of the download functions is covered in the installation instructions for the Downloading Software . Remote Programming Advisory Notes • Alarm and trouble reporting may be delayed during the time that the system and the Downloader are linked to each other following a valid exchange of codes, but the proper message will get through to the Central Station after the link is broken. • Keypad entries are ignored during the time interval stated above. • A copy of the program downloaded may be produced from the IBM PC compatible computer, using the product's in ternal report generator, when an optional printer is connected (consult your PC manual for proper printer and connections). • Program Upload or Download Time ÑApproximately one minute fifteen seconds for a complete program. – 22 – + – FOR COMPLETE INFORMATION, SEE INSTRUCTIONS ALARM OUTPUT 10.5-13.8VDC, 2A MAX. (600mA MAX FOR UL USAGE, INCLUDING AUX. POWER) STEADY FOR BURGLARY/PANIC, PULSING FOR FIRE (e.g. USE ADEMCO No. 740 SOUNDER, No.702 OR 719 SIREN, OR 12V BELL) CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER. 12 13 14 15 16 18 HANDSET 19 20 21 LOCATED AT LOWER RIGHT OF CIRCUIT BOARD RING (RED) INCOMING PHONE LINE TELEPHONE WIRING (VIA RJ31X* JACK DIRECT CONNECT CORD) *IN CANADA, CA38A JACK EARTH GROUND SEE INSTRUCTIONS FOR PROPER GROUNDING DOC LOAD NO.: 3 ZONE 6 REMOTE KEYPAD 17 TIP RING TIP (BROWN) (GRAY) (GREEN) ZONE 5 RED: KEYPAD PWR (+) BLACK: KEYPAD GROUND (–) RETURN PLUG-IN TRANSFORMER 16.5VAC, 25VA (e.g. ADEMCO No. 1321. USE No. 1321CN IN CANADA) 11 } } NOTE: KEYPAD CURRENT MUST BE INCLUDED IN AUX. CURRENT DRAIN CALCULATIONS TO 110VAC UNSWITCHED OUTLET (24HR) 10 ZONE 4 ▲ } – 23 – AUX. POWER OUTPUT 10.5-13.8VDC 500mA MAX. INTERRUPTS FOR FIRE ALARM RESET 9 ZONE 3 + 8 EARTH GROUND TERMINAL HEAT DETECTOR - ZONE 2 – 7 • 2000 1000 OHMS OHMS EOLR • EOLR HI 6 LO 5 HI 4 VIOLET TO LO SIDE OF SELECTED ZONE * IF PROGRAMMED FOR FIRE * IF PROGRAMMED FOR FIRE ZONE 1 3 YELLOW: DATA OUT TO KEYPAD 2 GREEN: DATA IN FROM KEYPAD 1 EOL POWER SUPERVISION RELAY MODULE A77-716B + 2–75* * TOZONES ZONE ▲ USE UL LISTED LIMITED ENERGY CABLE FOR ALL CONNECTIONS BLK RED GRN YEL LO BLK RED GRN YEL TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER OUTPUT AND REMOTE KEYPAD CURRENTS. • - SET RECEIVER’S 4-WIRE SMOKE DIP SWITCH FOR OR COMBUSTION DEVICE ADDRESS DETECTOR OF “0”. See receiver’s TO HI SIDE OF SELECTED ZONE instructions. ADEMCO 4281 or 5881* Type RF RECEIVER WIRELESS ZONES 4281L: UP TO 4 4281M/5881L: UP TO 8 5881M: UP TO 16 4281H/5881H/5881EH: UP TO 30 * 5882 TYPE IN CANADA (See Instructions) + RED BLK – 4 + LO – 5 - HI + CONNECTOR TABS AUX PWR + OUTPUT TERMS AND/OR HI RED LO + LO BLACK HI – BLK RED GRN YEL HI BATTERY 12V, 4AH (e.g. ADEMCO No. 467) OR 12V, 1.2AH ADEMCO No. 5800TM TRANSMITTER MODULE (20mA) (for No. 5827BD Wireless Bidirectional Keypad) AND/OR FA4285 VOICE MODULE (160mA) AND/OR ADEMCO LONG RANGE RADIO SET UNIT’S DIP SWITCH FOR DEVICE ADDRESS OF “1” See unit’s instructions. ADEMCO No. 4219 WIRED EXPANSION MODULE (8 ADD'L EOLR WIRED ZONES) -ORADEMCO No. 4229 WIRED EXPANSION/RELAY MODULE (8 ADD'L EOLR WIRED ZONES PLUS 2 OUTPUT RELAYS) -ORADEMCO No. 4204 RELAY MODULE (4 OUTPUT RELAYS) LO CHARGING VOLTAGE 13.8VDC THESE OPTIONAL ITEMS MAY ALSO BE USED SEE THEIR INSTRUCTIONS OPTIONAL FOR UP TO 30 ADDITIONAL ZONES (ONE FROM EITHER OR BOTH GROUPS) BATTERY FUSE (e.g. ADEMCO No. 90-12) GEL LEAD ACID TYPE. FOR REPLACEMENT BATTERY NORMALLY NEED NOT BE USE SAME VALUE REPLACED FOR AT LEAST 3 YRS. BATTERY CAPACITY FOR EMERGENCY STANDBY USE AT LEAST 4 HOURS. 3A 1000 OHMS EOLR 1000 OHMS EOLR 1000 OHMS EOLR 1000 OHMS EOLR 1000 OHMS EOLR 1000 OHMS EOLR REMOTE KEYPADS SYSTEM MUST BE PROGRAMMED WITH AN FA510KP OR FA550KP. IT NEED NOT REMAIN IN SYSTEM. AFTER PROGRAMMING, THE SYSTEM CAN USE: FA210KP (30mA), FA250KP (120mA), OR FA550KP (140mA). MULTIPLE KEYPADS MAY BE USED, BUT USE MAX. OF 220 FT. OF #22 WIRE OR 550 FT. OF #18. • MAXIMUM LOOP RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR) • RESPONSE, ZONES 1-6: 300-500MSEC • ZONE 3 CAN BE PROGRAMMED FOR N.C. SENSOR FAST RESPONSE TO AN OPEN: 10MSEC MAX • ZONE 5 CAN BE PROGRAMMED FOR USE AS A FIRE ZONE. SEE DIAGRAM. THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO. AC398U-68192-AL-E RINGER EQUIVALENCE: 0.7B. WARNING: TO PREVENT RISK OF SHOCK, DISCONNECT TELEPHONE LINE AT TELCO JACK BEFORE SERVICING THIS UNIT. THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 74 (NATIONAL FIRE PROTECTION ASSOC., BATTERYMARCH PARK, QUINCY, MA 02269). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION, TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT. WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED. WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. FA142C SUMMARY OF CONNECTIONS 1 72 Michael Drive Syosset, New York 11791 Copyright © 1997 PITTWAY CORPORATION
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 1998:10:05 20:54:08 Producer : Acrobat Distiller 3.01 for Windows Author : Administrator Title : FA142cprogform.pdf Modify Date : 1998:10:05 20:55:01 Page Count : 24 Page Mode : UseThumbsEXIF Metadata provided by EXIF.tools