Dis.4492 Scheda Tecnica Vigilo 2250 2280 I GB F D.FH11 File 1359030259
User Manual: File-1359030259
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
stroke 500 VIGILO 2250 410 170 Ø200 bollard thickness 4mm 1'350 FADINI l'apricance llo housing 850 410 Ø275 10 metres of cable Electric motor Limit switch TECHNICAL DATA stroke 800 FADINI l'apricance llo Ø200 VIGILO 2280 Ø275 10 metres of cable the gate opener Made in Italy GB Drwg. No. Electric motor Limit switch housing 1'140 410 1'940 170 bollard thickness 4mm 410 VIGILO is an electro-hydraulic post for traffic control. The motor pomp is incorporated and pre-connected. This makes the unit easier to install. The cylindrical post is made of steel, has a diametre of 200 mm and can be commanded to rise from the ground level or lower by remote control. Two options are available: Vigilo 2250 (500mm stroke) and Vigilo 2280 (stroke 800mm). All the essential component parts (motor pump and hydraulic actuator) are inside the location enclosure, which is made of cataphoresis treated steel, a special treatment to prevent rust, and designed to be sunk into the ground. The up and down movements are carried out by the piston shaft, directly connected to the top of the post from inside the unit. This automation is factory pre-set and calibrated making installation quick and easy in that no further adjusting is needed for proper operations. Just the electrical connections are required to be made on site for the electric motor and UP-cycle limit switch (10 m cables each are supplied with the equipment) to the electronic control board Elpro S40. Once the post has been driven to the upper limit stroke, the motor is stopped by means of a water-tight, fully sealed limit switch (limit switch Rising), on descending the motor is stopped when the post reaches the end of the permitted down stroke. The connections between the motor pump assembly, positioned in the front side of the automation, and the hydraulic actuator are by means of rigid copper pipes completely inside the foundation housing. A shaped universal spanner is supplied with the post to over-ride the hydraulic circuit in the pump inside the enclosure and lower the unit by hand if required. The cover of the square enclosure is designed to remain clear of standing water or other fluids. A brim is fitted to protect the top edge of the post. A back reflecting sticker, with red and yellow stripes, ensures full visibility of the post in daylight as well as in the dark, even in difficult weather conditions. All Vigilo automations are individually tested to ensure best performance at Meccanica Fadini. Oil-hydraulic motor-pump unit - Vico 2240 - Hydraulic actuator Electric motor Post weights Vigilo Range Hydraulic pump Pump flow rate Average working pressure Max. Achievable pressure Working temperature Hydraulic oil type Static weight of pump assembly Pump protection standards Power yield Supply voltage Frequency Absorbed current Absorbed power Capacitor Motor revolutions Service mode P10 4.45 l/min. 2 MPa (20 bar) 4 MPa (40 bar) -20°C +80°C Oil Fadini 10 Kg IP 54 Piston travel time Vigilo 2250 Piston travel time Vigilo 2280 Service stroke Vigilo 2250 Service stroke Vigilo 2280 Shaft diametre Piston diametre Pre-set Pushing Power Protection standard complete Static weight Vigilo 2250 (stroke 500 mm) Static weight Vigilo 2280 (stroke 800 mm) 0.25 KW (0.33 HP) 230 V 50 Hz 1.8 A 330 W 20 µF 2'800 rpm S3 Construction features Post colour Vigilo range Post, housing and cylindrical container material Anti-corrosion treatment Performance Vigilo 2250 Model Registered 4492 TECHNICAL SPECIFICATION TABLE Duty cycle 4s Rise - 30s Dwell - 4s Lower - 30s Dwell Time of one complete cycle 68s Complete cycles Rise - Dwell - Lower - Dwell No.53/hour Cycles per year (8 hours' service per day) No.154'000 102 Kg 131 Kg Anthracite greig RAL 7016 "Fe 360" steel Cataphoresis Performance Vigilo 2280 Duty cycle 6s Rise - 30s Dwell - 6s Lower - 30s Dwell Time of one complete cycle 72s Complete cycles Rise - Dwell - Lower - Dwell No.50/hour Cycles per year (8 hours' service per day) No.146'000 VIGILO 2250 VIGILO meccanica R RISING BOLLARDS 4s 6s 500 mm 800 mm 16 mm 30 mm 15 daN IP 557 R 2280 FADINI stroke 500 VIGILO 2250 410 170 Ø200 bollard thickness 4mm inox 1'350 FADINI l'apricance llo housing 850 410 Ø275 10 metres of cable Electric motor Limit switch TECHNICAL DATA stroke 800 FADINI l'apricance llo Ø200 VIGILO 2280 Ø275 10 metres of cable the gate opener Made in Italy GB Drwg. No. 6109 Electric motor Limit switch housing 1'140 410 1'940 410 170 bollard thickness 4mm inox VIGILO - inox - is an electro-hydraulic post for traffic control. The motor pomp is incorporated and pre-connected. This makes the unit easier to install. The cylindrical post is made of steel, has a diametre of 200 mm and can be commanded to rise from the ground level or lower by remote control. Two options are available: Vigilo 2250 - inox - (500mm stroke) and Vigilo 2280 - inox - (stroke 800mm). All the essential component parts (motor pump and hydraulic actuator) are inside the location enclosure, which is made of cataphoresis treated steel, a special treatment to prevent rust, and designed to be sunk into the ground. The up and down movements are carried out by the piston shaft, directly connected to the top of the post from inside the unit. This automation is factory pre-set and calibrated making installation quick and easy in that no further adjusting is needed for proper operations. Just the electrical connections are required to be made on site for the electric motor and UP-cycle limit switch (10 m cables each are supplied with the equipment) to the electronic control board Elpro S40. Once the post has been driven to the upper limit stroke, the motor is stopped by means of a water-tight, fully sealed limit switch (limit switch Rising), on descending the motor is stopped when the post reaches the end of the permitted down stroke. The connections between the motor pump assembly, positioned in the front side of the automation, and the hydraulic actuator are by means of rigid copper pipes completely inside the foundation housing. A shaped universal spanner is supplied with the post to over-ride the hydraulic circuit in the pump inside the enclosure and lower the unit by hand if required. The cover of the square enclosure is designed to remain clear of standing water or other fluids. A brim is fitted to protect the top edge of the post. A back reflecting sticker, with red and yellow stripes, ensures full visibility of the post in daylight as well as in the dark, even in difficult weather conditions. All Vigilo - inox - automations are individually tested to ensure best performance at Meccanica Fadini. Oil-hydraulic motor-pump unit - Vico 2240 - Hydraulic actuator Electric motor Post weights Vigilo Range - inox - Hydraulic pump Pump flow rate Average working pressure Max. Achievable pressure Working temperature Hydraulic oil type Static weight of pump assembly Pump protection standards Power yield Supply voltage Frequency Absorbed current Absorbed power Capacitor Motor revolutions Service mode P10 4.45 l/min. 2 MPa (20 bar) 4 MPa (40 bar) -20°C +80°C Oil Fadini 10 Kg IP 54 Piston travel time Vigilo 2250 inox Piston travel time Vigilo 2280 inox Service stroke Vigilo 2250 inox Service stroke Vigilo 2280 inox Shaft diametre Piston diametre Pre-set Pushing Power Protection standard complete Static weight Vigilo 2250 inox (stroke 500 mm) Static weight Vigilo 2280 inox (stroke 800 mm) 0.25 KW (0.33 HP) 230 V 50 Hz 1.8 A 330 W 20 µF 2'800 rpm S3 Construction features Material of the enclosure and structure " of the stainless steel post Performance Vigilo 2250 - inox - Model Registered TECHNICAL SPECIFICATION TABLE Duty cycle 4s Rise - 30s Dwell - 4s Lower - 30s Dwell Time of one complete cycle 68s Complete cycles Rise - Dwell - Lower - Dwell No.53/hour Cycles per year (8 hours' service per day) No.154'000 RISING BOLLARDS inox Stainless steel 4s 6s 500 mm 800 mm 16 mm 30 mm 15 daN IP 557 102 Kg 131 Kg "Fe 360" Inox "Aisi 304" Performance Vigilo 2280 - inox - Duty cycle 6s Rise - 30s Dwell - 6s Lower - 30s Dwell Time of one complete cycle 72s Complete cycles Rise - Dwell - Lower - Dwell No.50/hour Cycles per year (8 hours' service per day) No.146'000 VIGILO 2250 VIGILO meccanica R R 2280 FADINI FADINI l'apr icancello Ø200 Electric Motor cable Ø275 R bollard thickness 4mm housing 850 170 410x410 VIGILO 2251 1'350 LEDs stroke 500 CT TA N O EC Limit switch cable LED cable 10 metres electric IM EL ON cables each bundle Model Registered IT H ITC W S L UB O -D VIGILO 2281 R bollard thickness 4mm FADINI l'apr icancello n°8 LEDs Ø200 cables each bundle Electric Motor cable Limit switch cable Ø275 housing 1'140 170 1'940 410x410 10 metres electric LED cable the gate opener Made in Italy GB Drwg. No. 6456 TECHNICAL DATA Oil-hydraulic motor-pump unit - Vico 2240 - Hydraulic actuator Electric motor Bollard weights Vigilo Range Hydraulic pump Pump flow rate Average working pressure Max. Achievable pressure Working temperature Hydraulic oil type Static weight of pump assembly Pump protection standards stroke 800 n°8 VIGILO 2251 and VIGILO 2281 are electro-hydraulic posts for traffic control. The motor pomp is incorporated and pre-connected. This makes the unit easier to install. The cylindrical post is made of steel, has a diametre of 200 mm and can be commanded to rise from the ground level or lower by remote control. Two options are available: Vigilo 2251 (500mm stroke) and Vigilo 2281 (stroke 800mm), both models are fitted with mechanical limit switches, for rising and lowering cycles, and 8 led lamps for intermittent light. All the essential component parts (motor pump and hydraulic actuator) are inside the location enclosure, which is made of cataphoresis treated steel, a special treatment to prevent rust, and designed to be sunk into the ground. The up and down movements are carried out by the piston shaft, directly connected to the top of the post from inside the unit. This automation is factory pre-set and calibrated making installation quick and easy in that no further adjusting is needed for proper operations. Just the electrical connections are required to be made on site for the electric motor, led lamps and limit switches (supplied with the equipment in 10 m lengths, each) to the electronic control board Elpro S40. The movement of the post is stopped by means of a water-tight limit switch, operated by a sliding feeler, fitted on to the post. The connections between the motor pump assembly, positioned in the front side of the automation, and the hydraulic actuator are by means of rigid copper pipes completely inside the foundation housing. A shaped universal spanner is supplied with the post to over-ride the hydraulic circuit in the pump inside the enclosure and lower the unit by hand if required. The cover of the square enclosure is designed to remain clear of standing water or other fluids. A rubber brim is fitted to protect the top edge of the post. A back reflecting sticker, with red and yellow stripes, ensures full visibility of the post in daylight as well as in the dark, even in difficult weather conditions. All Coral posts are individually tested at Meccanica Fadini's to ensure best performance. Power yield Supply voltage Frequency Absorbed current Absorbed power Capacitor Motor revolutions Service mode P10 4.45 l/min. 2 MPa (20 bar) 4 MPa (40 bar) -20°C +80°C Oil Fadini 10 Kg IP 54 Piston travel time Vigilo 2251 Piston travel time Vigilo 2281 Service stroke Vigilo 2251 Service stroke Vigilo 2281 Shaft diametre Piston diametre Pre-set Pushing Power Protection standard complete 0.25 KW (0.33 HP) 230 V 50 Hz 1.8 A 330 W 20 µF 2'800 rpm S3 Performance Vigilo 2251 Duty cycle 4s Rise - 30s Dwell - 4s Lower - 30s Dwell Time of one complete cycle 68s Complete cycles Rise - Dwell - Lower - Dwell No.53/hour Cycles per year (8 hours' service per day) No.154'000 Static weight Vigilo 2251 (stroke 500 mm) Static weight Vigilo 2281 (stroke 800 mm) Construction features Post colour Vigilo range Post, housing and cylindrical container material Anti-corrosion treatment RISING BOLLARDS 102 Kg 131 Kg Anthracite greig RAL 7016 "Fe 360" steel Cataphoresis Performance Vigilo 2281 Duty cycle 6s Rise - 30s Dwell - 6s Lower - 30s Dwell Time of one complete cycle 72s Complete cycles Rise - Dwell - Lower - Dwell No.50/hour Cycles per year (8 hours' service per day) No.146'000 VIGILO 2251 VIGILO n°8 R TECHNICAL SPECIFICATION TABLE 4s 6s 500 mm 800 mm 16 mm 30 mm 15 daN IP 557 R LEDs 2281 meccanica FADINI
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2010:10:19 15:08:22+02:00 Create Date : 2009:12:10 15:57:43+01:00 Metadata Date : 2010:10:19 15:08:22+02:00 Format : application/pdf Title : dis.4492 Scheda tecnica Vigilo 2250-2280 I-GB-F-D.FH11 Creator : Andrea Document ID : uuid:bbc80f20-a18a-44ff-af1f-55e76fb9d9ca Instance ID : uuid:37aa6ed4-8edf-4ec2-a1b6-120f7bc909c9 Has XFA : No Page Count : 3 Author : AndreaEXIF Metadata provided by EXIF.tools