ZFM User ManualV13 Fingerprint Manual
Fingerprint%20user%20manual
User Manual: Fingerprint user manual
Open the PDF directly: View PDF 
.
Page Count: 26
| Download | |
| Open PDF In Browser | View PDF |
Fingerprint Identification Module User Manual -1- I Introduction Operation Principle Fingerprint processing includes two parts: fingerprint enrollment and fingerprint matching (the matching can be 1:1 or 1: N). When enrolling, user needs to enter the finger two times. The system will process the two time finger images, generate a template of the finger based on processing results and store the template. When matching, user enters the finger through optical sensor and system will generate a template of the finger and compare it with templates of the finger library. For 1:1 matching, system will compare the live finger with specific template designated in the Module; for 1: N matching, or searching, system will search the whole finger library for the matching finger. In both circumstances, system will return the matching result, success or failure. -2- II Main Parameters Power DC 3.8V-7.0V Interface UART(TTL logical level) Working current Typical: ＜65mA Matching Mode 1:1 and 1:N Baud rate Peak: ＜95mA (9600*N)bps, Character file size 256 bytes 512 bytes Storage capacity N=1～12 (default N=6） <1s Template size 1000 Security level FAR <0.001% FRR <1.0% Average searching time < 1s (1:500) Window dimension 14.5mm*19.4mm Working environment Temp: -20℃- +60℃ RH: 40%-85% Storage environment Temp: -40℃- +85℃ RH: <85% Integral type 54*20*20.5mm Image acquiring time Outline Dimention -3- 5 (1, 2, 3, 4, 5(highest)) III Hardware Interface 3.1 Connecting with upper computer 3.1.1 Serial Communication 1 Name Vtouch Type in 2 Sout Induction signal output（cable color:yellow） 3 Vin out in 4 TD out Data output. TTL logical level (cable color: green） 5 RD in Data input. TTL logical level (cable color: white) 6 GND － Signal ground. Connected to power ground (cable color: black） Pin Nmuber Function Description Touch induction power input（cable color: blue） Power input（cable color: red） 3.1.1.1 Hardware connection Via serial interface, the Module may communicate with MCU of 5V power: TD connects with RXD (receiving pin of MCU), RD connects with TXD (transferring pin of MCU). Should the upper computer (PC) be in RS-232 mode, please add level converting circuit, like MAX232, between the Module and PC. 3.1.1.2 Serial communication protocol The mode is semiduplex synchronism serial communication. And the default baud rate is 57600bps. User may set the baud rate in 9600～115200bps. Transferring frame format is 10 bit: the low-level starting bit, 8-bit data with the LSB first, and an ending bit. There is no check bit. start bit 1 0 stop bit D0 D1 D2 D3 D4 D5 10bit frame format -4- D6 D7 1 3.1.1.3 Reset time At power on, it takes about 300ms for initialization. During this period, the Module can't accept commands for upper computer. Module initialized immediately after sending a byte (0x55) to the host computer, said module can already work normally and the receiving host computer instruction. 3.1.1.4 Electrical parameter (All electrical level takes GND as reference) 1. Power supply Parameter Item Power Voltage (Vin) Maximum Voltage (Vinmax) Operation (Icc) Current Min 3.8 Typ 110 Peak Current (Ipeak) 2. Item Note V Normal working value. 9.0 V Exceeding the Maximum rating may cause permant harm to the Module. 130 mA 130 mA －0.3 90 Unit Max 7.0 TD（output, TTL logic level） Unit Parameter Condition Min Typ Max 0.4 3.3 VOL VOH IOL=－4mA IOH= 4mA 2.4 3. RD（input, TTL logic level） Item Condition Parameter Min Typ Max VIL 0.6 VIH 2.4 IIH 1 VIH =5V VIH =3.3V 30 5.5 VImax －0.3 V V Unit Note V V Loigc Logic mA uA V Maximum input voltage -5- 0 1 Note Logic 0 Logic 1 IV System Resources To address demands of different customer, Module system provides abundant resources at users use. 4.1 Notepad The system sets aside a 512-bytes memory (16 pages* 32 bytes) for user's notepad, where data requiring power-off protection can be stored. The host can access the page by instructions of PS_WriteNotepad and PS_ReadNotepad. Note: when write on one page of the pad, the entire 32 bytes will be written in wholly covering the original contents. 4.2 Buffer There are an image buffer and two 512-byte-character-file buffer within the RAM space of the module. Users can read & write any of the buffers by instructions. Note: Contents of the above buffers will be lost at power-off. 4.2.1 Image buffer ImageBuffer serves for image storage and the image format is 256*288 pixels. When transferring through UART, to quicken speed, only the upper 4 bits of the pixel is transferred (that is 16 grey degrees). And two adjacent pixels of the same row will form a byte before the transferring. When uploaded to PC, the 16-grey-degree image will be extended to 256-grey-degree format. That's 8-bit BMP format. 4.2.2 Character file buffer Character file buffer, CharBuffer1, CharBuffer2, can be used to store both character file and template file. 4.3 Fingerprint Library System sets aside a certain space within Flash for fingerprint template storage, that's fingerprint library. Contents of the library remain at power off. Capacity of the library changes with the capacity of Flash, system will recognize the latter automatically. Fingerprint template's storage in Flash is in sequential order. Assume the fingerprint capacity N, then the serial number of template in library is 0, 1, 2, 3……N-2, N-1. User can only access library by template number. 4.4 System Configuration Parameter To facilitate users developing, Module opens part system parameters for use. And the basic instructions are SetSysPara & ReadSysPara. Both instructions take Parameter Number as parameter. -6- When upper computer sends command to modify parameter, Module first responses with original configurations, then performs the parameter modification and writes configuration record into Flash. At the next startup, system will run with the new configurations. 4.4.1 Baud rate control (Parameter Number: 4) The Parameter controls the UART communication speed of the Module. Its value is an integer N, N= [1, 12]. Corresponding baud rate is 9600*N bps. 4.4.2 Security Level (Parameter Number: 5) The Parameter controls the matching threshold value of fingerprint searching and matching. Security level is divided into 5 grades, and corresponding value is 1, 2, 3, 4 and 5. At level 1, FAR is the highest and FRR is the lowest; however at level 5, FAR is the lowest and FRR is the highest. 4.4.3 Data package length (Parameter Number: 6) The parameter decides the max length of the transferring data package when communicating with upper computer. Its value is 0, 1, 2, 3, corresponding to 32 bytes, 64 bytes, 128 bytes, 256 bytes respectively. 4.5 System status register System status register indicates the current operation status of the Module. Its length is 1 word, and can be read via instruction ReadSysPara. Definition of the register is as follows: Bit Num 15 4 Description Reserved 3 ImgBufStat 2 1 0 PWD Pass Busy Note: Busy：1 bit. 1: system is executing commands; 0: system is free; Pass：1 bit. 1: find the matching finger; 0: wrong finger; PWD：1 bit. 1: Verified devices handshaking password. ImgBufStat：1 bit. 1: image buffer contains valid image. 4.6 Module password The default is 0x00000000，If the default password is not modified；If be modified through UART communication or password, the first instruction is the host computer and the communication module must be verify the password, only the password verification through, module can enter the normal working state, receiving other instructions（That is, the serial communication must first perform a handshake signal processing）. Password modification, new password stored in Flash, power cuts are still preserved（The modified password cannot be acquired through communication instructions, such as accidentally forgetting the modules cannot communicate, please kindly with）. 4.7 Module address Each module has an identifying address. When communicating with upper computer, each instruction/data is transferred in data package form, which contains the address item. Module system only responds to data package whose address item value is the same with its identifying address. The address length is 4 bytes, and its default factory value is 0xFFFFFFFF. User may modify the address via instruction SetAdder. The new modified address remains at power off. -7- V Communication Protocol 5.1 Data package format When communicating, the transferring and receiving of command/data/result are all wrapped in data package format. Data package format Header Adder Package identifier Package length Package content Checksum (instruction/data/Parameter） Definition of Data package Name Symbol Length Header START 2 bytes Fixed value of EF01H; High byte transferred first. 4 bytes Default value is 0xFFFFFFFF, which can be modified by command. High byte transferred first and at wrong adder value, module will reject to transfer. Adder Package identifier Package length Package contents Checksum ADDR PID 01H Command packet; 02H Data packet; Data packet shall not appear alone in executing process, must follow command packet or acknowledge packet. 07H Acknowledge packet; 08H End of Data packet. 1 byte LENGTH 2 bytes DATA － SUM Description 2 bytes Refers to the length of package content (command packets and data packets) plus the length of Checksum (2 bytes). Unit is byte. Max length is 256 bytes. And high byte is transferred first. It can be commands , data , command's parameters, acknowledge result, etc. (fingerprint character value, template are all deemed as data); The arithmetic sum of package identifier, package length and all package contents. Overflowing bits are omitted. High byte is transferred first. -8- 5.2 Check and acknowledgement of data package Note: Commands shall only be sent from upper computer to the Module, and the Module acknowledges the commands. Upon receipt of commands, Module will report the commands execution status and results to upper computer through acknowledge packet. Acknowledge packet has parameters and may also have following data packet. Upper computer can't ascertain Module's package receiving status or command execution results unless through acknowledge packet sent from Module. Acknowledge packet includes 1 byte confirmation code and maybe also the returned parameter. Confirmation code definition is: 1. 00h: command execution complete; 2. 01h: error when receiving data package; 3. 02h: no finger on the sensor; 4. 03h: fail to enroll the finger; 5. 06h: fail to generate character file due to the over-disorderly fingerprint image; 6. 07h: fail to generate character file due to weakness of character point or over-smallness of fingerprint image 7. 08h: finger doesn't match; 8. 09h: fail to find the matching finger; 9. 0Ah: fail to combine the character files; 10. 0Bh: addressing PageID is beyond the finger library; 11. 0Ch: error when reading template from library or the template is invalid; 12. 0Dh: error when uploading template; 13. 0Eh: Module can't receive the following data packages. 14. 0Fh: error when uploading image; 15. 10h: fail to delete the template; 16. 11h: fail to clear finger library; 17. 15h: fail to generate the image for the weakness of valid primary image; 18. 18h: error when writing flash; 19. 1Ah: invalid register number; -9- VI Module Instruction System 6.1 System-related instructions 6.1.1 Verify password :VfyPwd Description: The password verification module（Serial communication must be shake） Input Parameter: control code 0 Return Parameter: confirmation code; Instruction code: 13H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 4byte 2 bytes Header Chip address Package identifier Package length Instruction code Control code Checksum EF01H xxxx 01H 0007H 13H 0 001BH Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Chip address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: Port operation complete; Confirmation code=01H: error when receiving package; Confirmation code=13H: fail to operate the communication port; 6.1.2 Set password : SetPwd Description: Module password settings. (Refer to 4.6 for more information) Input Parameter: PassWord; Return Parameter: Confirmation code Instruction code: 12H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte Header Module address EF01H xxxx Package identifier Package length Instruction code 01H 0007H 12H 4byte 2 bytes PassWord Checksum PassWord sum Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes Header Module address Package identifier Package length EF01H xxxx 07H 0003H Note: Confirmation code=00H: OK; Confirmation code=01H: error when receiving package; - 10 - 1 byte Confirmatio n cod xx e H 2 bytes Checksum Sum 6.1.3 Set Module address: SetAdder Description: Set Module address. Input Parameter: New Module address Return Parameter: Confirmation code (1 byte) Instruction code: 15H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 4 bytes 2 bytes Header Original Module address Package identifier Package length Instruction code New Module address Checksum EF01H xxxx 01H 0007H 15H xxxx sum Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header New Module address Package identifier Package length Confirmation code Checksum EF01H xxxx xxH Sum 07H 0003H Note: Confirmation code=00H: address setting complete; Confirmation code=01H: error when receiving package; 6.1.4 Set module system’s basic parameter: SetSysPara Description: Operation parameter settings. (Refer to 4.4 for more information) Input Parameter: Parameter number+ Contents; Return Parameter: Confirmation code (1 byte) Instruction code: 0eH Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte Header Module address EF01H xxxx 1byte 1byte 2 bytes Package identifier Package length Instruction code Parameter number Contents Checksum 01H 0005H 0eH 4/5/6 xx sum Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum xxH Sum EF01H xxxx 07H 0003H Note: Confirmation code=00H: parameter setting complete; Confirmation code=01H: error when receiving package; Confirmation code=1aH: wrong register number; Table6.1 Parameter number+ Contents Name Parameter number Contents Baud rate 4 N(N=1~12, Corresponding baud rate is 9600*N bps.) Security level 5 N(1、2、3、4、5) Data package length 6 N(0、1、2、3，corresponding length is 32、64、128、 256（bytes）) - 11 - 6.1.5 Read system Parameter: ReadSysPara Description: Read Module’s status register and system basic configuration parameters（ ; Refer to 4.4 for system configuration parameter and 4.5 for system status register）. Input Parameter：none Return Parameter：Confirmation code (1 byte) + basic parameter（16bytes） Instruction code: 0Fh Command (or instruction) package format: 2 bytes 4bytes 1 byte Header Module address EF01H xxxx 2 bytes 1 byte 2 bytes Package identifier Package length Instruction code Checksum 01H 0003H 0fH 0013H Acknowledge package format: 2 bytes 4bytes 1 byte Header Module address EF01H xxxx 2 bytes 1 byte 16 bytes 2 bytes Package identifier Package length Confirmation code Basic parameter list Checksum 07H 0013H xxH See following Table6.2 sum Note: Confirmation code=00H: read complete; Confirmation code=01H: error when receiving package; Table6.2 system basic parameters Name Description Offset (word) Size (word) Contents of system status register 0 1 Fixed value: 0x0000 1 1 Finger library size 2 1 Security level Security level (1, 2, 3, 4, 5) 3 1 Device address 32-bit device address 4 2 Data packet size Size code (0, 1, 2, 3) 6 1 N (baud = 9600*N bps) 7 1 Status register System identifier code Finger library size Baud settings 6.1.6 Read the fingerprint template index table: ReadConList Description: Reading fingerprint template index table and each time the most read 256 fingerprint template. Input Parameter: Index page=0~3. Index page 0 representative read 0 ~ 255 fingerprint template index table Index page 1 representative read 256 ~ 511 fingerprint template index table Index page 2 representative read 512 ~ 767 fingerprint template index table Index page 3 representative read 768 ~ 1024 fingerprint template index table Return Parameter: Confirmation code (1 byte) + template index table Instruction code: 1fH Command (or instruction) package format: 2 bytes 4bytes 1 byte Header EF01H Module address 2 bytes 1 byte 1 byte Package identifier Package length Instruction code 01H 0004H 1FH xxxx Index page 0/1/2/3 2 bytes Checksum sum Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte Header Module address Package identifier Package length Confirmation code EF01H xxxx 07H 0023H xxH - 12 - 32 bytes Index table See following Table6.3 2 bytes Checksum sum 1：Confirmation code =0x00: Read index table success； Confirmation code =0x01: error when receiving package; 2：Every time the most read 256 fingerprint template index data, the data is insufficient 256 bit "0". 3：Index table data structure: each of the 8 as a group, and each group consists of beginning a high output. Table6.3 Index table data structure Order of transmission least significant byte From low to high byte output, and each byte by beginning a high output. 7 6 5 4 3 2 1 0 Template Number 0/1 0/1 0/1 0/1 0/1 Template index table 0/1 0/1 0/1 data 15 14 13 12 11 10 9 8 Template Number Template Number 0/1 0/1 0/1 0/1 0/1 Template index table 0/1 0/1 0/1 data … … … 255 254 253 252 251 250 249 248 Most significant byte Template Number 0/1 0/1 0/1 0/1 0/1 Template index table 0/1 0/1 0/1 data Note: the index table data "0" on behalf of the corresponding position without a valid template; "1" represents the corresponding to the location of the effective template. 6.1.7 Read valid template number: TempleteNum Description: read the current valid template number of the Module Input Parameter: none Return Parameter: Confirmation code (1 byte)，template number N Instruction code: 1dH Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 1DH 0021H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes 2 bytes Header Module address Package identifier Package length Confirmation code Template number Checksum N sum EF01H xxxx 07H 0005 xxH Note: Confirmation code=00H: read complete; Confirmation code=01H: error when receiving package; 6.2 Fingerprint-processing instructions 6.2.1 To collect finger image: GenImg Description: detecting finger and store the detected finger image in ImageBuffer while returning successful confirmation code; If there is no finger, returned confirmation code would be” can’t detect finger” . Input Parameter: none Return Parameter: Confirmation code (1 byte) Instruction code: 01H Command (or instruction) package format: - 13 - 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 01H 0005H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum xxH Sum EF01H xxxx 07H 0003H Note: Confirmation code=00H: finger collection success; Confirmation code=01H: error when receiving package; Confirmation code=02H: can’t detect finger; Confirmation code=03H: fail to collect finger; 6.2.2 Open the fingerprint lighting background LED : OpenLED Description: Open the fingerprint lighting background LED Input Parameter: none Instruction code: 50H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 50H 0054H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Confirmation code=00H: operation success； Confirmation code =others: operation failed 6.2.3 Close the fingerprint lighting background LED : CloseLED Description: Close the fingerprint lighting background LED Input Parameter: none Instruction code: 51H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 51H 0055H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Confirmation code=00H: operation success； Confirmation code =others: operation failed - 14 - 6.2.4 Fingerprint get image free lighting : GetmageFree Description: Fingerprint get image free lighting Input Parameter: none Instruction code: 52H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 52H 0056H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum xxH sum EF01H xxxx 07H 0003H Confirmation code =00H: finger collection success; Confirmation code =01H: error when receiving package; Confirmation code =02H: sensor has no finger; Confirmation code =03H: fail to collect finger 6.2.5 Handshake : GetEcho Description: Instructions to the module to send to shake hands, if the module is working correctly, will return to the confirmation code 0x55, the computer can continue to send instructions to the module; if the confirmation code for other or no response, said equipment abnormal. Input Parameter: none Instruction code: 53H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 53H 0057H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Confirmation code=55H: The equipment is normal, can receive the command； Confirmation code = Other or no response, said equipment abnormal. In addition, module after power on automatically send 0x55 as handshake marks, MCU detected after 0x55, can immediately send the command to enter the working state. 6.2.6 Auto-login : AutoLogin Description: Send the instruction, can make the module automatically complete the image acquisition, generation characteristics, synthetic template and the stored template work, To the four command line" To collect finger image (GenImg)", "To generate character file from image (Img2Tz)", "To generate template (RegModel) ", "To store template (Store)" into an instruction to complete. Input Parameter: Fingerprint wait time + Number of times for pressing the fingerprint +Stored sequence number Instruction code: 54H Command (or instruction) package format: - 15 - 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 1 byte 2 bytes 1 byte 2 bytes Header Module Package Package Instruction Fingerprint Number of times Stored Repeated Checksum address identifier length code wait time for pressing the sequence registration fingerprint number mark EF01H xxxx 01H 0003H 54H xxH 2/3 xxxx 0/1 sum 1. The fingerprint wait time is to wait the longest finger presses each image acquisition, if there is no finger presses on this parameter setting time, is that there is no finger. The domain values range from 1 to 255, the higher the value, the more time. The 70 series, usually taken as 54 (36H), corresponding to a time of 3.5 seconds, the other time intervals are listed in the following table: Real time interval（s） Real time interval（s） Fingerprint wait time Fingerprint wait time 31(1fH) 38(26H) 46(2eH) 54(36H) 2 2.5 3 3.5 62(3eH) 69(45H) 77(4dH) 85(55H) 4 4.5 5 5.5 2. Number of times for pressing the fingerprint is to Press the number of fingers to confirm the registration fingerprint, only the value of 2 or 3. Value of 2 represents the two press fingerprint recognition, value of 3 represents the 3 press fingerprint recognition. 3. Number of times for pressing the fingerprint is 2, the command will gather two fingerprint to register as a template, if collect the fingerprint success for the first time will sending a response code 56H (PS_AUTOLOGIN_OK1), then continue the second fingerprint process. Number of times for pressing the fingerprint is 3, the command will gather three fingerprint to register as a template, if collect the fingerprint success for the first time will sending a response code 56H (PS_AUTOLOGIN_OK1), and if collect the fingerprint success for the second time will sending a response code 57H (PS_AUTOLOGIN_OK2), then continue the third fingerprint process. 4. Repeated registration mark is set whether to allow repeated registration. 0 representative does not allow duplicate registration, i.e. if the current registration finger has been registered in the fingerprint database, then this will no longer register. 1 representative allows repeated registration, namely the current registration finger regardless of the fingerprint database whether registered, the registration of all. Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Confirmation code =00H: auto Login success Confirmation code =02H: sensor has no finger； Confirmation code=06H: fail to generate character file due to the over-disorderly fingerprint image; Confirmation code=07H: fail to generate character file due to lackness of character point or over-smallness of fingerprint image; Confirmation code =0aH: fail to combine the character files. That’s, the character files don’t belong to one finger； Confirmation code =0bH: the stored sequence number exceeds the effective range； Confirmation code =56H: the first finger collection success； Confirmation code =57H: the Second finger collection success； Confirmation code =24H: failure due to repeated registration（That is, the current registered fingerprint in fingerprint database already exists） - 16 - 6.2.7 Auto-Search : AutoSearch Description：Send the instruction, can make the module automatically complete the image acquisition, generation characteristics and search fingerprint in the fingerprint template library work. To the three command line " To collect finger image (GenImg)", "To generate character file from image (Img2Tz)", " To search finger library (Search) " into an instruction to complete. Input Parameter：Fingerprint wait time + Start page number + Search number. Instruction code：55H Command (or instruction) package format: 2 bytes Header 4bytes Module address EF01H xxxx 1 byte Package identifier 2 bytes Package length 01H 1 byte 1 byte 2 bytes Instruction Fingerprint Start page code wait time number 0008H 55H xxH 2 bytes Search number xxxx 2 bytes Checksum xxxx sum The fingerprint wait time is to wait the longest finger presses each image acquisition, if there is no finger presses on this parameter setting time, is that there is no finger. The domain values range from 1 to 255, the higher the value, the more time. The 70 series, usually taken as 54 (36H), corresponding to a time of 3.5 seconds, the other time intervals are listed in the following table: Real time interval（s） Real time interval（s） Fingerprint wait time Fingerprint wait time 31(1fH) 38(26H) 46(2eH) 54(36H) 2 2.5 3 3.5 2 bytes Header 4bytes Module address EF01H xxxx 62(3eH) 69(45H) 77(4dH) 85(55H) 4 4.5 5 5.5 Acknowledge package format: 1 byte 2 bytes 1 byte Package Package Confirmation identifier length code 07H 0007H xxH 2 bytes Number 2 bytes score 2 bytes Checksum xxxx xxxx sum Confirmation code =00H: search success； Confirmation code =09H: search failed； Confirmation code =02H: sensor has no finger； Confirmation code=06H: fail to generate character file due to the over-disorderly fingerprint image; Confirmation code=07H: fail to generate character file due to lackness of character point or over-smallness of fingerprint image; Confirmation code =22H: residual fingerprint； Confirmation code =23H: The specified interval does not exist an effective fingerprint template 6.2.8 Search fingerprints（With residual judgment）: SearchResBack Description：to search the whole or part finger library for the template that matches the one in CharBuffer1 or CharBuffer2. When found, PageID will be returned. This command with Search (Instruction code = 04H) difference is for the remaining fingerprint return code is different, SearchResBack detected residual return code 22H, and the Search command detection residual return code 09H Input Parameter：BufferID + StartPage + PageNum Return Parameter：Confirmation code + Number（Match the fingerprint template） Instruction code：56H Command (or instruction) package format: 2 bytes Header 4bytes 1 byte Module Package address identifier EF01H xxxx 01H Note: BufferID of CharBuffer1 and 2 bytes Package length 1 byte Instruction code 1 byte Buffer number 2 bytes 2 bytes StartPage Page number 0008H 56H BufferID StartPage PageNum CharBuffer2 are 1h and 2h respectively. - 17 - 2 bytes Checksum sum 2 bytes Header 4bytes Module address EF01H xxxx Acknowledge package format: 1 byte 2 bytes 1 byte Package Package Confirmation identifier length code 07H 0007H xxH 2 bytes Page number 2 bytes Score 2 bytes Checksum PageID MatchScore sum Confirmation code =00H，search success； Confirmation code =01H，error when receiving package; Confirmation code =09H，search failed; Confirmation code =22H，residual fingerprint 6.2.9 Upload image: UpImage Description: to upload the image in ImageBuffer to upper computer. Input Parameter: none Return Parameter: Confirmation code (1 byte) Instruction code: 0aH Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 0AH 000EH Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum 2 bytes N bytes 2 bytes Data package format（have subsequent packet）: 2 bytes 4bytes 1 byte Header Module address Package identifier Package length Contents Checksum EF01H xxxx 02H N+2 Image data Sum End package format（have not subsequent packets）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 08H N+2 Image data sum Note 1： Confirmation code=00H: ready to transfer the following data packet; Confirmation code=01H: error when receiving package; Confirmation code=0fH: fail to transfer the following data packet; 2：Module shall transfer the following data packet and end packet after responding to the upper computer. And data packet and end packet no reply packet. 3.The value of N(number of bytes of the packet content) is determined by the length of the packet content, factory package content length is set to 128 bytes. 6.2.10 Download the image: DownImage Description: to download image from upper computer to ImageBuffer. The image must be 256*288 size in BMP format. - 18 - Input Parameter: none Return Parameter: Confirmation code (1 byte) Instruction code: 0bH Command (or instruction) package format: 2 bytes 4bytes 1 byte Header EF01H Module address xxxx Acknowledge package format: 2 bytes 4bytes 2 bytes 1 byte 2 bytes Package identifier Package length Instruction code Checksum 01H 0003H 0bH 000FH 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum 2 bytes N bytes 2 bytes Data package format（have subsequent packet）: 2 bytes 4bytes 1 byte Header Module address Package identifier Package length Contents Checksum EF01H xxxx 02H N+2 Image data Sum End package format（have not subsequent packets）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 08H N+2 Image data sum Note: 1：Confirmation code=00H: ready to transfer the following data packet; Confirmation code=01H: error when receiving package; Confirmation code=0eH: fail to transfer the following data packet; 2：Module shall transfer the following data packet and end packet after responding to the upper computer. 3：The value of N (number of bytes of the packet content) is determined by the length of the packet content, factory package content length is set to 128 bytes. 6.2.11 To generate character file from image: Img2Tz Description: to generate character file from the original finger image in ImageBuffer and store the file in CharBuffer1 or CharBuffer2. Input Parameter: BufferID (character file buffer number) Return Parameter: Confirmation code (1 byte) Instruction code: 02H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Buffer number Checksum EF01H xxxx 01H 0004H 02H BufferID sum Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. Other values (except 1h, 2h) would be processed as CharBuffer2. Acknowledge package format: - 19 - 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: generate character file complete; Confirmation code=01H: error when receiving package; Confirmation code=06H: fail to generate character file due to the over-disorderly fingerprint image; Confirmation code=07H: fail to generate character file due to lackness of character point or over-smallness of fingerprint image; Confirmation code=15H: fail to generate the image for the lackness of valid primary image; 6.2.12 To generate template: RegModel Description: To combine information of character files from CharBuffer1 and CharBuffer2 and generate a template which is stored back in both CharBuffer1 and CharBuffer2. Input Parameter：none Return Parameter：Confirmation code (1 byte) Instruction code: 05H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 05H 09H 2 bytes 1 byte 2 bytes Acknowledge package format: 2 bytes 4bytes 1 byte Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: operation success; Confirmation code=01H: error when receiving package; Confirmation code=0aH: fail to combine the character files. That’s, the character files don’t belong to one finger. 6.2.13 To upload character or template: UpChar Description: to upload the character file or template of CharBuffer1/CharBuffer2 to upper computer; Input Parameter: BufferID (Buffer number) Return Parameter: Confirmation code (1 byte) Instruction code: 08H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Buffer number Checksum EF01H xxxx 01H 0004H 08H BufferID sum - 20 - Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Data package format（have subsequent packet）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 02H N+2 Template data Sum End package format（have not subsequent packets）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 08H N+2 Template data sum Note 1: Confirmation code=00H: ready to transfer the following data packet; Confirmation code=01H: error when receiving package; Confirmation code=0dH: error when uploading template; 2: Module shall transfer following data packet after responding to the upper computer.; 3.The value of N(number of bytes of the packet content) is determined by the length of the packet content, factory package content length is set to 128 bytes. 4: The instruction doesn’t affect buffer contents. 6.2.14 To download character file or template: DownChar Description: to download character file or template from upper computer to the specified buffer of Module; Input Parameter: BufferID (buffer number) Return Parameter: Confirmation code (1 byte) Instruction code: 09H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes Header Module address Package identifier Package length Instruction code buffer number Checksum EF01H xxxx 01H 0004H 09H BufferID sum Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH Data package format（have subsequent packet）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 02H N+2 Template data Sum - 21 - sum End package format（have not subsequent packets）: 2 bytes 4bytes 1 byte 2 bytes N bytes 2 bytes Header Module address Package identifier Package length Contents Checksum EF01H xxxx 08H N+2 Template data sum Note 1: Confirmation code=00H: ready to transfer the following data packet; Confirmation code=01H: error when receiving package; Confirmation code=0eH: fail to receive the following data packages. 2: Module shall transfer the following data packet after responding to the upper computer. 3.The value of N(number of bytes of the packet content) is determined by the length of the packet content, factory package content length is set to 128 bytes. 6.2.15 To store template: Store Description: to store the template of specified buffer (Buffer1/Buffer2) at the designated location of Flash library. Input Parameter: BufferID(buffer number)+PageID（Flash location of the template, two bytes with high byte front and low byte behind） Return Parameter: Confirmation code (1 byte) Instruction code: 06H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes 2 bytes Header Module address Package identifier Package length Instruction code buffer number Location number Checksum EF01H xxxx 01H 06H 0006H BufferID PageID Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum sum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: storage success; Confirmation code=01H: error when receiving package; Confirmation code=0bH: addressing PageID is beyond the finger library; Confirmation code=18H: error when writing Flash. 6.2.16 To read template from Flash library: LoadChar Description: to load template at the specified location (PageID) of Flash library to template buffer CharBuffer1/CharBuffer2 Input Parameter: BufferID(buffer number)+PageID (Flash location of the template, two bytes with high byte front and low byte behind)。 Return Parameter: Confirmation code (1 byte)Instruction code: 07H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes 2 bytes Header Module address Package identifier Package length Instruction code buffer number Page number Checksum EF01H xxxx 01H 0006H 07H BufferID PageID sum Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. - 22 - Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: load success; Confirmation code=01H: error when receiving package; Confirmation code=0cH: error when reading template from library or the readout template is invalid; Confirmation code=0BH: addressing PageID is beyond the finger library; 6.2.17 To delete template: DeletChar Description: to delete a segment (N) of templates of Flash library started from the specified location (or PageID); Input Parameter: PageID (template number in Flash)+ N (number of templates to be deleted) Return Parameter: Confirmation code (1 byte) Instruction code: 0cH Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes 2bytes 2 bytes Header Module address Package identifier Package length Instruction code Page number number of templates to be deleted Checksum EF01H xxxx 01H 0007H 0cH PageID N sum Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: delete success; Confirmation code=01H: error when receiving package; Confirmation code=10H: failed to delete templates; 6.2.18 To empty finger library: Empty Description: to delete all the templates in the Flash library Input Parameter: none Return Parameter: Confirmation code (1 byte) Instruction code: 0dH Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code Checksum EF01H xxxx 01H 0003H 0dH 0011H Acknowledge package format: 2 bytes 4bytes Header Module address 1 byte 2 bytes 1 byte 2 bytes Package identifier Package length Confirmation code Checksum - 23 - EF01H xxxx 07H 0003H Note: Confirmation code=00H: empty success; Confirmation code=01H: error when receiving package; Confirmation code=11H: fail to clear finger library; xxH sum 6.2.19 To carry out precise matching of two finger templates: Match Description: to carry out precise matching of templates from CharBuffer1 and CharBuffer2, providing matching results. Input Parameter: none Return Parameter: Confirmation code (1 byte) + matching score. Instruction code: 03H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Instruction code EF01H xxxx 01H 0003H Checksum 03H 0007H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte Header Module address Package identifier Package length Confirmation code EF01H 2 bytes 2 bytes Matching score Checksum xxxx 07H 0005H xxH xxH sum Note 1: Confirmation code=00H: templates of the two buffers are matching; Confirmation code=01H: error when receiving package; Confirmation code=08H: templates of the two buffers aren’t matching; 2: The instruction doesn’t affect the contents of the buffers. 6.2.20 To search finger library: Search Description: to search the whole or part finger library for the template that matches the one in CharBuffer1 or CharBuffer2. When found, PageID will be returned. Input Parameter: BufferID+StartPage (searching start address)+ PageNum（searching numbers） Return Parameter: Confirmation code (1 byte)+PageID (matching templates location） Instruction code: 04H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1 byte 2 bytes 2 bytes Header Module address Package identifie r Package length EF01H xxxx 01H 0008H Instructio n code 04H 2 bytes buffer number Start page number Number Checksum BufferID StartPage PageNum sum Note: BufferID of CharBuffer1 and CharBuffer2 are 1h and 2h respectively. Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte Header Module address Package identifier Package length Confirmation code 2 bytes Page EF01H xxxx 07H 0007H xxH PageID Note 1: Confirmation code=00H: found the matching finer; Confirmation code=01H: error when receiving package; - 24 - 2 bytes Score 2 bytes Checksum MatchScore sum Confirmation c o d e =09H: No ma t c h i n g i n the library (both the PageID and matching score are 0); 2: The instruction doesn’t affect the contents of the buffers. 6.3 Other instructions 6.3.1 To write note pad: WriteNotepad Description: for upper computer to write data to the specified Flash page; Input Parameter: NotePageNum, user content (or data content) Return Parameter: Confirmation code (1byte) Instruction code: 18H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes Header Module address Package identifier EF01H xxxx 01H Package length 1 byte 1byte 32 bytes 2 bytes Instruction code Page number Data content Checksum 18H 0~15 content sum 0024H Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 2 bytes Header Module address Package identifier Package length Confirmation code Checksum EF01H xxxx 07H 0003H xxH sum Note: Confirmation code=00H: write success; Confirmation code=01H: error when receiving package; 6.3.2 To read note pad: ReadNotepad Description: to read the specified page’s data content;. Input Parameter: none Return Parameter: Confirmation code (1 byte) + data content Instruction code: 19H Command (or instruction) package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 1byte 2 bytes Header Module address Package identifier Package length Instruction code Page number Checksum EF01H xxxx 01H 0004H 19H 0~15 xxH Acknowledge package format: 2 bytes 4bytes 1 byte 2 bytes 1 byte 32bytes 2 bytes Header Module address Package identifier Package length Confirmation code User content Checksum EF01H xxxx 07H 0023H xxH content Note: Confirmation code=00H: read success; Confirmation code=01H: error when receiving package; - 25 - sum Dimentions Dimentions of integral type Module（unit：mm） - 26 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 26 Language : zh-CN Tagged PDF : Yes Title : Microsoft Word - ZFM user manualV13.doc Author : babyface Creator : Microsoft® Word 2013 Create Date : 2014:11:10 09:35:57+08:00 Modify Date : 2014:11:10 09:35:57+08:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools