Front End Signal Conditioners Owner's Guide Owners

• Safety Notes
  • Statement of Intended Use
    • Safety and Quality Standards
    • General Safety Instructions
      • Bio Amp Safety Instructions
      • Stimulus Isolator Safety Instructions
      • Earthing and Ground Loop Noise
    • Cleaning and Sterilization
    • Inspection and Maintenance
    • Environment
      • Storage Conditions
      • Operating Conditions
      • Disposal
• Overview
  • Introduction
    • Checking the Front-end
    • Connecting to the PowerLab
      • Single Front-ends
      • Multiple Front-ends
      • Special Cases
        • Connecting Stimulator Front-Ends
        • Maximum Number of Front-Ends
    • Using ADInstruments Programs
      • Front-end Drivers
      • The Front-end Self-test
      • Software Behavior
    • Preventing Problems
      • Aliasing
      • Frequency Distortion
      • Saturation
      • Ground Loops
        • Mains filter
        • Notch Filter
      • Electrode Contact
      • Motion Artifacts
• Animal Bio Amp
  • The Animal Bio Amp
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
    • Using LabChart and Scope
      • The Bio Amp dialog
    • Using the Animal Bio Amp
      • Some Suitable Uses
      • Some Unsuitable Uses
      • The Animal Bio Amp Input
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Bio Amp
  • Bio Amp Safety Instructions
    • The Bio Amp front-ends
      • The Back Panel
    • Connecting to the PowerLab
      • Using More Than One Bio Amp
      • The Bio Amp Cable
    • Using LabChart
      • The Bio Amp dialog
    • Using the Bio Amp
      • Some Suitable Uses
      • Some Unsuitable Uses
      • Recording Technique
        • Right-leg Drive
    • Troubleshooting
    • Specifications
      • Single Bio Amp
      • Dual Bio Amp
      • Quad/Octal Bio Amp
        • Electromagnetic Compatibility
• BP Amp
  • The BP Amp
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
    • Equipment and Technique
      • The Disposable BP Transducer
    • Using LabChart and Scope
      • The BP Amp dialog
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Bridge Amp
  • The Bridge Amp
    • The Front Panel
      • The Back Panel
    • Setting Up
    • Connecting to the PowerLab
    • Using LabChart and Scope
      • The Bridge Amp dialog
    • Using Transducers
      • Compatibility
      • Suitable Transducers
      • Unsuitable Transducers
      • How Transducers Work
      • Checking the Transducer
        • Using Grass Transducers with Bridge Amps
    • Adapting Transducers
      • Introduction
      • Setting the Excitation Voltage
      • Wiring Up the Transducer
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Dual Bio Amp/Stimulator
  • The Dual Bio Amp/Stimulator
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
    • Using LabChart and Scope
      • The Bio Amp dialog
    • The Stimulator
    • Using the Dual Bio Amp/Stimulator
      • Some Suitable Uses
      • Some Unsuitable Uses
      • Recording Technique
    • Technical Aspects
    • Troubleshooting
    • Specifications
• GSR Amp
  • The GSR Amp
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
    • Using LabChart and Scope
      • The GSR Amp dialog
    • Equipment and Technique
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Neuro Amp EX
  • The Neuro Amp
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
      • Single Front-end
      • Multiple Front-ends
        • Using More Than One Neuro Amp EX
        • Software Requirements
    • Using LabChart and Scope
      • Neuro Amp EX dialog
    • Types of Measurement
      • The Neuro Amp EX Headstage
      • Recording Technique
      • Setting up to Record From a Subject
        • Motion Effects
        • Electrode Contact
    • Technical Aspects
      • The Neuro Amp EX Input
    • Troubleshooting
    • Specifications
      • Neuro Amp EX Front-end [FE185]
      • Neuro Amp EX Headstage [MLT185]
      • Electromagnetic Compatibility
• pH Amp
  • The pH Amp
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
      • Single Front-end
      • Multiple Front-ends
    • Using LabChart and Scope
      • The pH Amp dialog
      • Calibrating the pH Amp Electrode
      • Setting Up the Temperature Signal
        • The Temperature Probe
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Spirometer
  • The Spirometer
    • The Front Panel
      • The Back Panel
    • Connecting to the PowerLab
    • Using LabChart and Scope
      • The Spirometer dialog
    • Using the Spirometer
      • Fitting the Flow Head
      • Calibrating the Flow Head
        • Using an approximate conversion factor
        • Injecting a known volume and integrating
        • Using the Spirometry Extension
        • Reducing Drift
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Stimulator HC
  • The Stimulator HC
    • The Front Panel
      • The Safety Switch
      • The Back Panel
    • Connecting to the PowerLab
    • The Stimulator HC dialog
      • Choosing How Stimulation Should Start
      • Creating a Custom Stimulus Waveform
      • The Stimulator Panel
      • PowerLabs with Independent versus Differential Analog Outputs
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Stimulus Isolator
  • The Stimulus Isolator
    • The Front Panel
      • The Safety Switch
      • The Back Panel
    • Connecting to the PowerLab
    • The Stimulus Isolator dialog
      • Choosing How Stimulation Should Start
      • Choosing a Stimulus Type
      • Setting Stimulus Parameters
      • The Stimulator Panel
    • Technical Aspects
    • Troubleshooting
    • Specifications
• Warranty