GSM800E Videx 4836 1 4000 Series
User Manual: GSM800E Videx 4836-1 4000 series
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
GSM-800E V&VK V1.0 Installation Manual Programming Installation 1) Before you install this equipment, please read this full manual. 2) Ensure that there is good network reception at the location where it will be installed. Speech Unit 200mm min 4-5 feet minimum 3) For medium or low reception areas, to reduce audio interference on a call, install an optional external antenna. Ensure it is kept as high as possible, and ABOVE all electronics. Programming is best done by SMS text. It can also be done by DTMF from a normal telephone. 1) First check reception. Send the following SMS to the unit... The unit should reply SIGNAL LEVEL = ? Where ? will be between 1 and 31 Below 14 can cause problems with relay operation, or no voice from the gate to the house. Take action to improve reception. 1-12 Poor *20# 13-20 Medium 21-31 Good 2) Program the numbers you wish the unit to dial when the call button is pressed, up to a maximum of 3 numbers. Each SMS must start with the pass code, default 1234, in the following format *12*1234#, followed immediately by a command. E.g to program the telephone number 0987654321, enter the following SMS.. Entrance Pillar Side View Wiring *12*1234#110987654321# 4) Carefully follow the wiring instructions. Additional wiring suggestions for electric strike lock and magnetic lock are shown overleaf. Pass code Data Function code Up to 3 numbers can be sent together in a single SMS as follows.. *12*1234#11tel.number1#12tel.number2#13tel.number3# 11 = Telephone number 1 12 = Telephone number 2 13 = Telephone number 3 3) It is recommended to change the “no answer” time if there is more than 1 number stored. This stops the unit ringing a number after a set time, and can be used to prevent voicemail answering the call. Send the following SMS.. *12*1234#52??# Where ?? can be 2 digits from 10-99 seconds, default is 20. The unit can allow up to 100 telephone numbers to be stored, for users to be able to ring the system for automatic entry. This uses caller ID like a phone to determine the identity of the caller. First, the unit must know what country it is operating in. 4) Program the country code as follows.. Optional Antenna (Elevated position) Speech panel GSM module Intercom Transmitter Shielded CAT5 cable 8 meters max. Keep short as possible for best audio quality. *12*1234#71??# Where ?? can be 1-3 digits. For uk, insert 44, for Ireland 353. Do not use any leading zeros. 5) Enter the telephone numbers required to have access control. Do not enter country code, just the complete number as you would dial it.. *12*1234#720987654321# Up to 3 numbers can be sent together in the same SMS. Just add 72 then the number, then # each time. The pass code only needs to be put at the beginning of each new messge. Additional Programming Parameters GSM-3E SIM card 5) Register your SIM card with the network, and check it works in a mobile phone first. If you are using a Pre-pay or Pay&Go SIM, it will need topped up first. Your SIM should be GSM compatible. 6) Ensure the power is OFF before inserting the SIM card. 7) Carefully slide the SIM holder in the OPEN direction, insert the SIM, and slide in the CLOSED direction to lock it in place. Do NOT Force or use a screwdriver! 8) After a final check of wiring, switch on the power. 9) Allow 20-30 seconds for the unit to boot up and detect the network. Once successful connection has been made, the unit will sound a confirmation tone and the status LED will begin flashing. If there is a fault or problem, the unit will emit a series of bleeps or warning tones. If this occurs, check... 1) That the SIM card has been activated and has credit. 2) That the SIM card does not require a PIN code, disable this in a phone. 3) That the SIM card can make and received a call on a phone. 4) If the SIM card was purchased with a phone, that it is not locked to that phone. Call the network operator to check. 5) Switch off power, remove and reseat the SIM card and try again. Code Description Default 01????# Change programming password. 1234 02????# Change access control password (allows users not in caller ID list to call intercom and use pass code to activate relay). 5678 03????# Change monitoring mode password (dial to listen in mode) 1212 1n*# Delete a button calling number, where n = number 1,2 or 3. N/A 3?# Speaker volume. Where ? = level 0 - 4 3 4?# Microphone volume. Where ? = level 0 - 4 3 51?# Relay time. Where ? = 1-9999 seconds. 1 sec 53??# Max call time. Where ??? = 005-999 seconds (3 digit code) 60 sec 55??# Max monitoring time (for listen in mode when calling the intercom) 00-60 mins. 00 = no limit. 10 min 57??# Unit can call or SMS service number by set duration to prevent SIM card deactivation if seldom used. 00-60 days. 00 = no inform. 00 58?# Choose between scheduled call to service number or send SMS to service number. ?=1 for SMS, 2 for call. 1 77number# Store service number to receive scheduled SMS or call from intercom. N/A 77*# Delete service number. N/A 65?# Dial in mode for withheld numbers or non stored numbers. 1 = answer the call & wait for pass code. 2 = answer the call & automatically activate 2 way speech. 73??# Delete phone number for caller ID access. N/A 73*# Delete all phone numbers for caller ID access. N/A 999# Restore defaults N/A *21# Check stored numbers. Note: no pass code needed for this command. O = dial out number. I = Dial in number. N/A 1 Remember to begin each new SMS with pass code *12*1234# Note: DTMF Programming is done by calling the unit, & entering the pass code first, then after a long single confirm tone, commands can be entered. A fault is indicated by 3 short bleeps. Fault finding & FAQs Additional Wiring Information A/C Strike Lock Wiring Q. The unit will not power up. No LEDs on. A. Check power supply voltage is within 11.5V-12.5V DC. GSM module DETECT GND PB GND N/O COM N/C VCC AC AC A/C PSU for lock Strike lock From 12v d.c. power supply Break Glass Exit Button N/O C1 NC1 NO1 Optional emergency break glass unit Keypad module D/C Magnetic Lock Wiring Q. The unit powers up but there is a bleeping from the door station. A. This means the unit is not able to detect the network for some reason. -Check the SIM card is activated and has calling credit. -Power off the unit, remove the SIM and check it in a mobile phone to verify it can make a call. -Check the SIM does not ask for a PIN code when put in a phone. If it does, then disable the PIN code request. -Check the SIM is a standard GSM SIM, not 3G or 4G only SIM. If you are unsure, contact your SIM card provider to verify. Frequency of operation should be any one of the international quad band standards, 850 / 900 / 1800 / 1900 MHz. -Check the reception is good. Poor reception is not sufficient. -Check the antenna has been mounted as high as possible, not near large metal objects, or wet green shrubs etc. -Check the antenna connection. Visually inspect that the centre pin inside the antenna is intact, and has not been pushed back inside the fitting. Q. The unit calls the first number, but there is not enough time to answer before it diverts to the next number. A. Increase the no answer time as per programming instructions. GSM module DETECT GND PB GND N/O COM N/C VCC AC AC Q. The unit calls the first number but voicemail comes on before it can ring the second number. A. Decrease the no answer time as per programming instructions. D/C PSU for lock Recommend diode fitted here Magnetic Lock From 12v d.c. power supply Break Glass Exit Button N/C C1 NC1 NO1 Optional emergency break glass unit Keypad module Keypad Programming (only for VK model) Enter engineers code Factory default is 111111 Press ENTER Enter access code for relay 3 Press ENTER 4-8 digits Press ENTER Enter pulse time for relay 1 Press ENTER Enter access code for relay 2 Q. There is no audio from the gate, but the person at the gate can hear ok. A. This can be due to low reception. -Check reception level by *20#. -Change SIM card if necessary to another network which may have better coverage. -Purchase a high gain antenna. This may also be caused by either a defective microphone, or incorrect microphone wiring, or a short circuit by whiskers between the centre core and the shielding, or excessive microphone cable length. Press ENTER Confirm or change engineers code Enter access code for relay 1 Enter pulse time for relay 2 Q. The caller ID part does not work. A. Be sure to program the caller ID part under 72 feature. If your number is a private or number withheld, then it will not work. Even if you have already programmed a number to receive a call from the intercom, if you also want that number to have caller ID access, it must be programmed under the 72 feature also. Ensure the number is entered as you would normally dial it from another phone. Do not put the country code in front of the number. Enter the country code in which the unit is operating in separate under the 71 feature. International callers ringing the intercom may not work. Press ENTER Enter pulse time for relay 3 Press ENTER 2 digits, 01-99. E.g. 03=3 sec Press ENTER FINISH Red LED should now be OFF Q. The audio quality that can be heard on the remote telephone is poor or humming (buzzing). A. A small amount of GSM buzz can be considered normal on GSM intercoms, but not so much that causes inability to hear the person speaking. This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough. -Try earthling the speech panel chassis to 0V of the power supply. -This is also a symptom of poor reception. Try above steps on checking and improving reception. Q. The * or # key does not work when the intercom calls a phone. A. Check if you can hear the relay clicking at the gate when the * or # key is pressed during a call. If it can be heard, then the system is working, check wiring between the relay and the lock or gate panel. If the relays do not make a clicking sound, then check this feature on a different mobile cell phone or landline. If it works on a different phone, check the settings on the phone in question under DTMF tones. Failure of DTMF tones to operate correctly is also a symptom of low reception. Check steps above on improving reception. Try pressing the buttons longer when attempting to activate the gates or door. User Manual For GSM 800 Videx 4000 series Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed. There are several modes of operation depending on how the unit has been programmed by your installer. The following instructions will assume default programming. Intercom calling your phone Press * to open OR 1 4 7 Call button pressed * 2 5 8 0 END Answer call. Press # to hold open 3 6 9 # and Press 1 to release again (Only some gate systems allow hold open control, depending on manufacturer) Sending SMS Commands Default pass code 5678 is shown in all examples. This may have been changed by your installer. Latch or hold open gate / door Unlatch gate / door SEND SMS SEND SMS SEND SMS SEND SMS SEND SMS *33*5678# *34*5678# *35*5678# *22# *21# Trigger Gate / Door 1 4 7 1 2 3 1 2 3 2 3 5 6 4 5 6 4 5 6 8 9 7 8 9 7 8 9 HOLD OPEN FEATURE, OR “PARTY MODE” 0 systems # Some allow*hold 0 open #control, depending * gate * 0 on # manufacturer. Send the following SMS commands to control the gates.. If limit switch fitted, check gate status.. 1 2 3 4 5 6 Reply will indicate 9 7 8or closed. opened * 0 # Check stored numbers 1 2 3 4 5 6 O = dial out number 9 for I =7Dial 8 in number caller ID0access. # * Calling the intercom options *33*5678# Dialling… MY GATE 1 4 7 * END Option 1) If your number is saved inside the intercom memory, just dial it and it will activate the door or gate without answering your call. The intercom will end the call for you. 2 5 8 0 3 6 9 # END Option 2) If your number is not saved in the intercom memory, it will answer the call. Enter the code on your telephone keypad to activate the door or gate (default code shown). Fig.2 wiring diagram IMPORTANT: Do NOT drill holes in the top or near the top of the enclosure. Do NOT use silicone sealants! Intercom Transmitter GSM 800 Keep short as possible, 8 meters max Wiring Gate Status Button8 Button7 Button6 Button2 Button1 - + Egress Mic PWR IN Speaker Reset Button 12v or 15v d.c. ONLY WARNING Do NOT use 24v ac. Connect to the buttons module Button2 Button3 Button4 Button5 Button6 2 P3 P4 3 1 C C1 P1 P2 S S1 Solid core of shield connected to 0V on PCB above for better audio quality. Relay 1 Relay 2 Relay 3 SW2 SW1 NC3 NO3 C3 NC2 NO2 C2 NC1 NO1 C1 + 7 8 9 Shielded CAT5 Press Button5 GSM LED Status LED Power LED 1 Button4 *# Press Speech Panel Connections 12v out + Relay 1 Momentary Latch Unlatch Relay 2 Momentary Latch Unlatch Button3 LOCK OPEN Antenna connector. Finger tighten only! Keypad Connections (VK models only) Microphone
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 4 Trapped : True Author : KonradSamczyk Creator : Serif DrawPlus 11, 0, 3, 23 (Feb 25, 14:12:55) Title : GSM800E Videx 4836-1 4000 series Create Date : 2015:03:19 15:54:06Z Producer : PDFlib+PDI 6.0.0p2 (Win32)EXIF Metadata provided by EXIF.tools