Grundfos CR1 Pump User Manual
User Manual: Grundfos CR1 Pump User Manual
Open the PDF directly: View PDF 
.
Page Count: 84
| Download | |
| Open PDF In Browser | View PDF |
GRUNDFOS DATA BOOKLET CR, CRI, CRN, CRE, CRIE, CRNE Vertical multistage centrifugal pumps 50 Hz Contents Product data Introduction Performance range - CR, CRI, CRN Performance range - CRE, CRIE, CRNE Applications Product range Pump Motor Terminal box positions Ambient temperature Viscosity 3 4 4 5 6 7 7 8 8 8 Control of E-pumps Examples of E-pump applications Central management system Remote control Control panel Control modes for E-pumps CRE, CRIE, CRNE with integrated pressure sensor CRE, CRIE and CRNE without sensor 9 10 10 10 11 11 11 12 12 13 13 14 22 24 26 28 30 32 34 36 40 42 44 46 48 60 62 64 Motor data 66 67 Pumped liquids Pumped liquids List of pumped liquids 68 68 Accessories Operating and inlet pressures Maximum operating pressure and temperature range 15 Operating range of the shaft seal 15 Maximum inlet pressure 16 Selection and sizing Selection of pumps How to read the curve charts Guidelines to performance curves CR 1s CRI, CRN 1s CR, CRE 1 CRI, CRN, CRIE, CRNE 1 CR, CRE 3 CRI, CRN, CRIE, CRNE 3 CR, CRE 5 CRI, CRN, CRIE, CRNE 5 CRI, CRN, CRIE, CRNE 10 CR, CRE 15 CRI, CRN, CRIE, CRNE 15 CR, CRE 20 CRI, CRN, CRIE, CRNE 20 CRN, CRNE 64 CR, CRE 90 CRN, CRNE 90 Standard motors for CR, CRI, CRN, 50 Hz E-motors for CRE, CRIE, CRNE, 50 Hz Construction CR(E) 1s, 1, 3, 5, 10, 15 and 20 CRI(E), CRN(E) 1s, 1, 3, 5, 10, 15 and 20 CR(E) 32, 45, 64 and 90 CRN(E) 32, 45, 64 and 90 Type keys Performance curves Technical data 17 21 21 Pipework connection Counter flanges for CR(E) Counter flanges for CRN(E) PJE couplings for CRN(E) FlexiClamp base connections Potentiometer for CRE, CRIE, CRNE G10-LON interface for CRE, CRIE, CRNE LiqTec for CR(E), CRI(E) and CRN(E) Remote control, R100 EMC-filter for CRE, CRIE, CRNE Sensors for CRE, CRIE, CRNE 70 70 72 74 74 77 77 77 77 77 78 Variants Lists of variants - on request 79 Further product documentation WinCAPS WebCAPS 2 80 81 Product data CR, CRI, CRN, CRE, CRIE, CRNE Introduction CRE, CRIE, CRNE pumps TM02 7397 3403 This data booklet deals with CR, CRI and CRN as well as CRE, CRIE and CRNE pumps. GR5381 Fig. 2 CRE, CRIE and CRNE pumps Fig. 1 CR, CRI and CRN pumps CRE, CRIE and CRNE pumps are built on the basis of CR, CRI, CRN pumps. CRE, CRIE and CRNE pumps belong to the so-called E-pump family. CRE, CRIE and CRNE pumps are referred to as E-pumps. CR, CRI and CRN pumps are vertical multistage centrifugal pumps. The in-line design enables the pump to be installed in a horizontal one-pipe system where the suction and discharge ports are in the same horizontal plane and have the same pipe dimensions. This design provides a more compact pump design and pipework. The difference between the CR and the CRE pump range is the motor. CRE, CRIE and CRNE pumps are fitted with an E-motor, i.e. a motor with built-in frequency control. Grundfos CR pumps come with various pump sizes and various numbers of stages to provide the flow and the pressure required. Frequency control enables continuously variable control of motor speed, which makes it possible to set the pump to operation at any duty point. The aim of continuously variable control of the motor speed is to adjust the performance to a given requirement. CR pumps are suitable for a variety of applications from pumping of potable water to pumping of chemicals. The pumps are therefore used in a wide diversity of pumping systems where the performance and material of the pump meet specific demands. The CR pumps consist of two main components: The motor and the pump unit. The motor of CR pumps is a Grundfos motor designed to EN standards. The pump unit consists of optimised hydraulics, various types of connections, an outer sleeve, a pump head and various other parts. CR pumps are available in various material versions according to the pumped liquid. The motor of the CRE pump is a Grundfos MGE or MMGE motor designed to EN standards. CRE, CRIE and CRNE pumps are available with an integrated pressure sensor connected to the frequency control. The pump materials are the same as those of the CR, CRI and CRN pump range. Selecting a CRE pump Select a CRE pump if: • controlled operation is required, i.e. consumption fluctuates, • constant pressure is required, • communication with the pump is required. Adaptation of performance through frequency-controlled speed control offers obvious advantages: • Energy savings. • Increased comfort. • Control and monitoring of the pump performance. 3 Product data CR, CRI, CRN, CRE, CRIE, CRNE Performance range - CR, CRI, CRN H [m] 50 Hz 400 300 CR 32 CRN 32 200 100 80 60 CR 1s CR 3 CR 10 CR 20 CR 64 CRI 1s CRI 3 CRI 10 CRI 20 CRN 64 CRN 1s 40 30 CRN 3 CRN 10 CRN 20 CR 1 CR 5 CR 15 CR 45 CR 90 CRI 1 CRI 5 CRI 15 CRN 45 CRN 90 CRN 1 CRN 5 CRN 15 20 0.8 1 1 0.8 1 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 Q [m³/h] 2 3 4 5 6 8 10 20 30 40 50 60 80 100 Q [m³/h] Eta [%] 80 60 20 0 High pressure range TM02 1192 3605 40 Performance range - CRE, CRIE, CRNE H [m] 50 Hz 300 200 100 80 60 CRE 1 CRE 5 CRE 15 CRE 32 CRE 64 CRIE 1 CRIE 5 CRIE 15 CRNE CRNE 64 CRNE 1 CRNE 5 CRNE 15 32 CRE 3 CRE 10 CRE 20 CRE 45 CRIE 3 CRIE 10 CRIE 20 CRNE 45 CRNE 3 CRNE 10 CRNE 20 40 CRE 90 CRNE 90 20 0.8 1 4 1 2 3 4 5 6 8 10 20 30 40 50 60 80 100 Q [m³/h] TM02 7281 3605 30 Product data CR, CRI, CRN, CRE, CRIE, CRNE Applications Application CR, CRI CRN CRE, CRNE Water supply Filtration and transfer at waterworks Distribution from waterworks Pressure boosting in mains Pressure boosting in high-rise buildings, hotels, etc. Pressure boosting for industrial water supply Industry Pressure boosting in... process water systems washing and cleaning systems vehicle washing tunnels fire fighting systems Liquid transfer in... cooling and air-conditioning systems (refrigerants) boiler feed and condensate systems machine tools (cooling lubricants) aquafarming Transfer of... oils and alcohols acids and alkalis glycol and coolants Water treatment Ultra-filtration systems Reverse osmosis systems Softening, ionising, demineralizing systems Distillation systems Separators Swimming baths Irrigation Field irrigation (flooding) Sprinkler irrigation Drip-feed irrigation Recommended version. Alternative version. CRT, CRTE version available. For further information about CRT, CRTE pumps see, "Pumped liquids" page 68 or related CRT, CRTE data booklet. 5 Product data CR, CRI, CRN, CRE, CRIE, CRNE Product range Range Nominal flow rate [m3/h] CR 1s CR, CRE 1 CR, CRE 3 0.8 1 3 Temperature range [°C] CR, CRE 10 CR, CRE 15 5 10 15 CR, CR, CR, CR, CR, CRE 20 CRE 32 CRE 45 CRE 64 CRE 90 20 32 –20 to +120 Temperature range [°C] – on request Max. pump efficiency [%] CR, CRE 5 45 64 90 –30 to +120 –40 to +180 –40 to +180 35 48 58 66 70 72 72 78 79 80 81 0.3-1.1 0.7-2.4 1.2-4.5 2.5-8.5 5-13 9-24 11-29 15-40 22-58 30-85 45-120 21 22 24 24 22 23 25 28 26 20 20 - 47 47 47 47 47 47 39 40 39 39 0.37-1.1 0.37-2.2 0.37-3 0.37-5.5 0.37-7.5 1.1-15 1.1-18.5 1.5-30 3-45 4-45 5.5-45 Flow range [m3/h] - 0.7-2.4 1.2-4.5 2.5-8.5 5-13 8.5-23.5 10.5-29 15-40 22-58 30-85 45-120 Max. pressure [bar] - 22 24 24 22 23 25 28 26 20 20 Motor power [kW] - 0.37-2.2 0.37-3 0.37-5.5 0.37-7.5 1.1-15 1.1-18.5 1.5-22 3-22 4-22 5.5-22 - - - - CR pumps Flow range [m3/h] Max. pressure [bar] High pressure [bar] – on request Motor power [kW] CRE pumps Version CR, CRE: Cast iron and stainless steel EN 1.4301/AISI 304 CRI, CRIE: Stainless steel EN 1.4301/AISI 304 CRN, CRNE: Stainless steel EN 1.4401/AISI 316 CRT, CRTE: Titanium See the CRT, CRTE data booklet. CR, CRE pipe connection Oval flange (BSP) Rp 1 Rp 1 Rp 1 Rp 1¼ Rp 1½ Rp 2 Rp 2 - - - - Rp 2½ Rp 2½ - - - - Oval flange (BSP) – on request Rp 1¼ Rp 1¼ Rp 1¼ Rp 1 Rp 1¼ Rp 2 Flange DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 40 DN 50 DN 50 DN 65 DN 80 DN 100 DN 100 - - - - DN 50 - - DN 80 DN 100 DN 125 DN 125 Flange – on request CRI, CRIE pipe connection Oval flange (BSP) Rp 1 Rp 1 Rp 1¼ Rp 1¼ Rp 1½ Rp 2 Rp 2 - - - - Oval flange (BSP) – on request Rp 1¼ Rp 1¼ Rp 1 Rp 1 Rp 2 - - - - - - Flange DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 40 DN 50 DN 50 - - - - - - - - DN 50 - - - - - - PJE coupling (Victaulic) R 1¼ DN 32 R 1¼ DN 32 R 1¼ DN 32 R 1¼ DN 32 R2 DN 50 R2 DN 50 R2 DN 50 - - - - Clamp coupling (L-coupling) ø48.3 ø48.3 ø48.3 ø48.3 ø60.3 ø60.3 ø60.3 - - - - G2 G2 G2 G2 G 2¾ G 2¾ G 2¾ - - - - Flange – on request Union (+GF+) CRN(E) pipe connection Oval flange (BSP) Rp 1 Rp 1 Rp 1¼ Rp 1¼ Rp 1½ Rp 2 Rp 2 - - - - Oval flange (BSP) – on request Rp 1¼ Rp 1¼ Rp 1 Rp 1 Rp 2 - - - - - - Flange DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 25/ DN 32 DN 40 DN 50 DN 50 DN 65 DN 80 DN 100 DN 100 - - - - DN 50 - - DN 80 DN 100 DN 125 DN 125 PJE coupling (Victaulic) R 1¼ DN 32 R 1¼ DN 32 R 1¼ DN 32 R 1¼ DN 32 R2 DN 50 R2 DN 50 R2 DN 50 R 3 1) R 4 1) R 4 1) R 5 1) Clamp coupling (L-coupling) ø48.3 ø48.3 ø48.3 ø48.3 ø60.3 ø60.3 ø60.3 - - - - G2 G2 G2 G2 G 2¾ G 2¾ G 2¾ - - - - Flange – on request Union (+GF+) 1) On request 6 Product data CR, CRI, CRN, CRE, CRIE, CRNE Pump Electrical tolerances according to EN 60034. The CR and CRE pumps are non-self-priming, vertical multistage centrifugal pumps. From 0.37 to 1.1 kW Grundfos offers CRE pumps fitted with single-phase MGE motors (1 x 200-240 V). The pumps are available with a Grundfos standard motor (CR pumps) or a frequency-controlled motor (CRE pumps). Electrical data CR, CRI, CRN pumps MG motor The pump consists of a base and a pump head. The chamber stack and the outer sleeve are secured between the pump head and the base by means of staybolts. The base has suction and discharge ports on the same level (in-line). All pumps are equipped with a maintenance-free mechanical shaft seal of the cartridge type. Mounting designation Up to 4 kW: V 18 From 5.5 kW: V 1 Insulation class F Efficiency class EFF 1 (0.37-0.75 kW and 3 kW are EFF 2) Enclosure class IP 55 Supply voltage (Tolerance: ±10%) Supply frequency Motor P2: 0.37-1.5 kW: 3 x 220-240/380-415 V, 50 Hz P2: 2.2-45 kW: 3 x 380-415, 50 Hz 50 Hz IP 44, IP 54 and IP 65 - on request. CRE, CRIE, CRNE pumps Coupling Shaft seal (Cartridge type Impellers MGE motor (P2 ≤ 7.5 kW) Mounting designation Up to 4 kW: V 18 From 5.5 kW: V 1 Insulation class F Efficiency class EFF 1 Enclosure class IP 54 Pump head Outer sleeve Supply voltage (Tolerance: ±10%) Staybolts Base Base plate GR5357 - GR3395 Supply frequency Fig. 3 CR pump Motor Grundfos standard motors - MG and Siemens motors CR, CRI and CRN pumps are fitted with a totally enclosed, fan-cooled, 2-pole Grundfos standard motor with principal dimensions in accordance with the EN standards. P2: 0.37-1.1 kW: 1 x 200-240 V P2: 0.75-7.5 kW: 3 x 380-480 V MGE motor (P2 ≥ 11-22 kW) EFF 2 P2: 11-22 kW: 3 x 380-415 V 50/60 Hz Single-phase MGE motors are EFF 2. Optional motors The Grundfos standard range of motors covers a wide variety of application demands. However, for special applications or operating conditions, custom-built motor solutions can be provided. For special applications or operating conditions, Grundfos offers custom-built motors such as: • ATEX approved motors, • MG motors with anti-condensation heating unit, • motors with thermal protection. Electrical tolerances according to EN 60034. From 0.37 to 2.2 kW Grundfos offers CR pumps fitted with single-phase MG motors (1 x 220-230/240 V). Frequency-controlled motors - MGE CRE, CRIE and CRNE pumps are fitted with a totally enclosed, fan-cooled, 2-pole frequency-controlled motor with principal dimensions in accordance with the EN standards. 7 Product data CR, CRI, CRN, CRE, CRIE, CRNE Motor protection Ambient temperature MG and Siemens motors Single-phase Grundfos motors have a built-in thermal overload switch (IEC 34-11: TP 211). 0.37-0.75 kW motors (EFF 2, MG): Max. +40°C. 1.1-11 kW motors (EFF 1, MG): Max. +60°C. Three-phase motors must be connected to a motor starter in accordance with local regulations. Three-phase Grundfos motors from 3 kW and upwards have a built-in thermistor (PTC) according to DIN 44 082 (IEC 34-11: TP 211). MGE motors CRE, CRIE, CRNE pumps require no external motor protection. The MGE motor incorporates thermal protection against slow overloading and blocking (IEC 3411: TP 211). 15-45 kW motors (EFF 1, Siemens): Max. +55°C. If the ambient temperature exceeds above maximum values or if the motor is located 1000 metres above sea level, the motor output (P2) must be reduced due to the low density and consequently low cooling effect of the air. In such cases, it may be necessary to use a motor with a higher rated output. P2 [%] EFF 1, Siemens 100 EFF 1, MG 90 EFF 2, MG 80 60 As standard the terminal box is mounted on the suction side of the pump. 50 20 25 30 35 40 45 50 55 60 65 70 75 80 t [°C] 1000 2250 3500 4750 m TM03 1868 3305 70 Terminal box positions Position Stellung 66 Standard Position Stellung99 Position Stellung 12 12 Fig. 4 Terminal box positions 8 Position Stellung 33 TM02 18 05 2001 Fig. 5 Relationship between motor output (P2) and ambient temperature Viscosity The pumping of liquids with densities or kinematic viscosities higher than those of water will cause a considerable pressure drop, a drop in the hydraulic performance and a rise in the power consumption. In such situations the pump should be equipped with a larger motor. If in doubt, contact Grundfos. Control of E-pumps Examples of E-pump applications CRE, CRIE and CRNE pumps are the ideal solution in a number of applications characterized by a need for variable flow at constant pressure. The pumps are suited for water supply systems and pressure boosting, but also industrial applications. Depending on the nature of the application, the pumps offer energy-savings, increased comfort and improved processing. E-pumps in the service of industry Industry uses a large number of pumps in many different applications. Demands on pumps in terms of pump performance and mode of operation make speed control a must in many applications. Below is mentioned some of the applications in which E-pumps are often used. CR, CRI, CRN, CRE, CRIE, CRNE Constant flow • Steam boiler systems, • Condensate systems, • Sprinkler irrigation systems, • Chemical industry, etc. Example: In a steam boiler, it is important to be able to monitor and control pump operation to maintain a constant level of water in the boiler. By using an E-pump with level sensor in the boiler, it is possible to maintain a constant water level. A constant water level ensures optimum and cost-efficient operation as a result of a stable steam production. Dosing applications • Chemical industry (i.e. control of pH-values), • Petrochemical industry, • Paint industry, Constant pressure • Water supply, • Degreasing systems, • Washing and cleaning systems, Example: In the petrochemical industry, E-pumps with pressure sensor are used as dosing pumps. The Epumps helps to ensure that the correct mixture ratio is achieved when more liquids are combined. • Distribution from waterworks, • Humidifying systems, • Water treatment systems, • Process boosting systems, etc. Example: Within industrial water supply, E-pumps with integrated pressure sensor are used to ensure a constant pressure in the piping network. From the sensor, the E-pump receives inputs about changes of pressure as a result of changes in the consumption. The E-pump responds to the input by adjusting the speed until the pressure is equalized. The constant pressure is stabilized once more on the basis of a preset setpoint. Constant temperature • Air-conditioning systems at industrial plants, • Industrial cooling systems, • Industrial freezing systems, • Casting and moulding tools, etc. Example: In industrial freezing systems, E-pumps with temperature sensor increase comfort and lower operating costs compared with pumps without a temperature sensor. An E-pump continuously adapts its performance to the changing demands reflected in the differences in temperature of the liquid circulating in the freezing system. Thus, the lower the demand for cooling, the smaller the quantity of liquid circulated in the system and vice versa. • Bleaching systems, etc. E-pumps functioning as dosing pumps improves processing and offer energy-savings. E-pumps in commercial building services Commercial building services use E-pumps to maintain a constant pressure or a constant temperature based on a variable flow. Constant pressure • Water supply in high-rise buildings i.e. office buildings, hotels, etc. Example: E-pumps with pressure sensor are used for water supply in high-rise buildings to ensure a constant pressure even at the highest draw-off point. As the consumption pattern and thus the pressure changes during the day, the E-pump continuously adapts its performance until the pressure is equalized. Constant temperature • Air-conditioning systems in hotels, schools, • Building cooling systems, etc. Example: E-pumps are an excellent solution in buildings where constant temperature is essential. E-pumps keep the temperature constant in air-conditioned highrise glass buildings, irrespective of the seasonal fluctuations of the out-door temperature, and various heat impacts inside the building. 9 Control of E-pumps CR, CRI, CRN, CRE, CRIE, CRNE Control options of E-pumps Communication with CRE, CRIE, CRNE pumps is possible by means of Remote control • a central management system, The operator communicates with the E-pump by pointing the IR-signal transmitter at the control panel of the E-pump terminal box. • remote control (Grundfos R100) or • a control panel. The R100 remote control produced by Grundfos is available as an accessory. TM00 4498 2802 The purpose of controlling an E-pump is to monitor and control the pressure, temperature, flow and liquid level of the system. Central management system Communication with the E-pump is possible even though the operator is not present near the E-pump. Communication is enabled by having connected the Epump to a central management system allowing the operator to monitor and change control modes and setpoint settings of the E-pump. Fig. 7 R100 remote control On the R100 display it is possible to monitor and change control modes and settings of the E-pump. Control panel Control management system The control panel of the E-pump terminal box makes it possible to change the setpoint settings manually. Light fields Buttons LON Interface eg.G10 or G100 Indicator lights Fig. 8 Control panel on CRE pump E-pump Fig. 6 Structure of a central management system 10 TM02 6592 1404 GENIbus connection TM00 7600 0404 LON connection Control of E-pumps CR, CRI, CRN, CRE, CRIE, CRNE Control modes for E-pumps Grundfos offers CRE, CRIE and CRNE pumps in two different variants: In constant-curve mode, the pump is not controlled. It can be set to pump according to a preset pump characteristic within the range from min. curve to max. curve, see figure below. • CRE, CRIE and CRNE with integrated pressure sensor H • CRE, CRIE and CRNE without sensor. Max. CRE, CRIE, CRNE with integrated pressure sensor CRE, CRIE and CRNE pumps with integrated pressure sensor are suitable for applications where you want to control the pressure after the pump, irrespective of the flow. For further information, see the section "Examples of E-pump applications" page 9. Signals of pressure changes in the piping system are transmitted continuously from the sensor to the pump. The pump responds to the signals by adjusting its performance up or down to compensate for the pressure difference between the actual and the desired pressure. As this adjustment is a continuous process, a constant pressure is maintained in the piping system. TM00 9323 1204 Min. Q Fig. 11 Constant curve mode CRE, CRIE and CRNE without sensor CRE, CRIE and CRNE pumps without sensor are suitable for applications where • uncontrolled operation is required • you want to fit another sensor later in order to control the flow, temperature, differential temperature, liquid level, pH value, etc at some arbitrary point in the system. CRE, CRIE and CRNE pumps without sensor can be set to: • controlled-operation mode or • uncontrolled-operation mode (factory-setting). H Max. Min. Fig. 9 CRE, CRIE and CRNE pumps A CRE, CRIE or CRNE pump with integrated pressure sensor facilitates installation and commissioning. CRE, CRIE and CRNE pumps with integrated pressure sensor can be set to: Q set Q Fig. 12 Constant flow mode In uncontrolled-operation mode, the pump operates according to the constant curve set, see figure below. • constant-curve mode. H In constant-pressure mode, the pump maintains a preset pressure after the pump, irrespective of the flow, see figure below. Max. Min. Q Fig. 10 Constant pressure mode TM00 9322 4796 H Q TM00 9323 1204 • constant-pressure mode (factory setting) or Hset TM02 7264 2803 TM02 7398 3403 In controlled-operation mode, the pump adjusts its performance to the desired setpoint, see figure below. Fig. 13 Constant curve mode CRE, CRIE and CRNE pumps can be fitted with sensor types meeting the requirements mentioned in the data booklet titled "Grundfos E-pumps". 11 Construction CR, CRI, CRN, CRE, CRIE, CRNE TM02 1808 2001 - GR7373 - GR7375 CRI(E), CRN(E) 1s, 1, 3, 5, 10, 15 and 20 TM02 1198 0601 - GR7377 - GR7379 CR(E) 1s, 1, 3, 5, 10, 15 and 20 Sectional drawing Sectional drawing 1 1 3 3 10 2 6 7 5 6 7 5 9 TM02 1194 1403 9 8 8 11 Materials: CRI(E), CRN(E) Materials: CR(E) Pos. Designation 10 4 Materials Pos. Designation EN/DIN AISI/ASTM EN-JL1030 ASTM 25B 1 Pump head Materials Cast iron EN-GJL-200 1) EN/DIN AISI/ASTM EN-JL1030 ASTM 25B 1 Pump head Cast iron EN-GJL-200 3 Shaft Stainless steel 1.4401 AISI 316 AISI 431 2 Pump head cover Stainless steel 1.4408 CF 8M eq. to AISI 316 4 Impeller Stainless steel 1.4301 AISI 304 3 Shaft Stainless steel 5 Chamber Stainless steel 1.4301 AISI 304 1.4401 2) 1.4460 3) AISI 316 AISI 329 6 Outer sleeve Stainless steel 1.4301 AISI 304 8 Base Stainless steel 1.4408 CF 8M eq. to AISI 316 7 O-ring for outer sleeve EPDM or FKM Neck ring Shaft seal 8 Base Cast iron EN-GJL-200 9 10 11 Base plate EN-JL1030 ASTM 25B 9 Neck ring PTFE 10 Shaft seal PTFE Cartridge type Cast iron EN-GJL-200 1) EPDM or FKM CRI(E) Stainless steel Stainless steel Stainless steel 1.4301 1.4301 1.4301 AISI 304 AISI 304 AISI 304 1.4401 1.4401 1.4401 AISI 316 AISI 316 AISI 316 Rubber parts EPDM or FKM EN-JL1030 ASTM 25B Rubber parts 4 5 6 7 Impeller Chamber Outer sleeve O-ring for outer sleeve EPDM or FKM CRN(E) Impeller Stainless steel Chamber Stainless steel Outer sleeve Stainless steel O-ring for 7 EPDM or FKM outer sleeve 1) Stainless steel available on request. 2) CRI(E), CRN(E) 1S, 1, 3, 5 3) CRI(E), CRN(E) 10, 15, 20 4 5 6 12 TM02 1195 1403 4 Construction CR, CRI, CRN, CRE, CRIE, CRNE CRN(E) 32, 45, 64 and 90 TM02 7399 3403 TM01 2150 1298 - GR5952 CR(E) 32, 45, 64 and 90 Sectional drawing Sectional drawing 2 2 3 3 10 4 1 6 5 11 7 8 12 6 5 11 7 8 9 12 13 Materials: CRN(E) Materials: CR(E) Pos. Designation 1 TM01 1836 1403 9 4 TM01 1837 1403 10 Materials Pos. Designation Materials EN/DIN AISI/ASTM EN-JS1050 ASTM 80-55-06 1 Pump head EN-JL1030 ASTM 25B 2 Motor stool EN/DIN AISI/ASTM Stainless steel 1.4408 CF 8M eq. to AISI 316 Cast iron EN-GJL-200 1) EN-JL1030 ASTM 25B 1 Pump head Cast iron EN-GJS-500-7 2 Motor stool Cast iron EN-GJL-200 3 Shaft Stainless steel 1.4057 AISI 431 3 Shaft Stainless steel 1.4462 4 Impeller Stainless steel 1.4301 AISI 304 4 Impeller Stainless steel 1.4401 AISI 316 5 Chamber Stainless steel 1.4301 AISI 304 5 Chamber Stainless steel 1.4401 AISI 316 6 Outer sleeve Stainless steel 1.4301 AISI 304 6 Outer sleeve Stainless steel 1.4401 AISI 316 7 O-ring for outer sleeve EPDM or FKM 7 O-ring for outer sleeve EPDM or FKM 8 Base Cast iron EN-GJS-500-7 8 Base Stainless steel 1.4408 CF 8M eq. to AISI 316 9 Neck ring Carbon-graphite filled PTFE 9 Neck ring Carbon-graphite filled PTFE EN-JS1050 ASTM 88-55-06 EN-JS1050 ASTM 80-55-06 10 Shaft seal 10 Shaft seal 11 Bearing ring Bronze 11 Bearing ring 12 Bottom bearing ring Tungsten carbide/Tungsten carbide 12 Rubber parts EPDM or FKM Tungsten carBottom bearbide/Tungsten ing ring carbide 13 Base plate Carbon-graphite filled PTFE Cast iron EN-GJS-500-71) Rubber parts EPDM or FKM 1) Stainless steel available on request. 13 Construction Type keys CR, CRI, CRN, CRE, CRIE, CRNE Codes Example CR(E), CRI(E), CRN(E) Example Pump version CR E 32 (s) -4 -2 -A -F -G -E -HQQE Type range: CR, CRI, CRN A Basic version B Oversize motor F Pump with integrated frequency control CR pump for high temperatures (air-cooled top assembly) H Horizontal version Flow rate [m3/h] HS All impellers with reduced diameter (applies only to CR, CRI, CRN 1s) High-pressure pump with high speed MGE motor I Different pressure rating Number of impellers J Pump w/different max. speed Number of reduced-diameter impellers (CR(E), CRN(E) 32, 45, 64, 90) K Pump with low NPSH M Magnetic drive Code for pump version N Fitted with sensor Code for pipe connection P Undersize motor R Horizontal version with bearing bracket SF High pressure pump X Special version Code for materials Code for rubber parts Code for shaft seal Pipe connection A Oval flange B NPT thread CA FlexiClamp (CRI(E), CRN(E) 1, 3, 5, 10, 15, 20) F DIN flange G ANSI flange J JIS flange N Changed diameter of ports P PJE coupling X Special version Materials A Basic version D Carbon-graphite filled PTFE (bearings) G Wetted parts 1.4401/AISI 316 GI All parts stainless steel, wetted parts 1.4401/AISI 316 I Wetted parts 1.4301/AISI 304 II All parts stainless steel, wetted parts 1.4301/AISI 304 K Bronze (bearings) S SiC bearings + PTFE neck rings X Special version Code for rubber parts E EPDM F FXM K FFKM V FKM Shaft seal H 14 Balanced cartridge seal Q Silicon carbide U Tungsten carbide B Carbon E EPDM F FXM K FFKM V FKM A -F -A -E -H QQ E Operating and inlet pressures CR, CRI, CRN, CRE, CRIE, CRNE Maximum operating pressure and temperature range Maximum and temperature operating range pressure TM02 1383 1101 PJE, Clamp, UNION, DIN TM02 1379 1101 Oval flange Max. permissible Liquid temperature Max. permissible operating pressure range operating pressure Liquid temperature range CR, CRI, CRN 1s 16 bar –20°C to +120°C 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 1 16 bar –20°C to +120°C 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 3 16 bar –20°C to +120°C 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 5 16 bar –20°C to +120°C 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 10-1 CR(E), CRI(E), CRN(E) 10-16 16 bar –20°C to +120°C 16 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 10-17 CR(E), CRI(E), CRN(E) 10-22 - - 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 15-1 CR(E), CRI(E), CRN(E) 15-7 10 bar –20°C to +120°C - - CR(E), CRI(E), CRN(E) 15-1 CR(E), CRI(E), CRN(E) 15-10 - - 16 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 15-12 CR(E), CRI(E), CRN(E) 15-17 - - 25 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 20-1 CR(E), CRI(E), CRN(E) 20-7 10 bar –20°C to +120°C - - CR(E), CRI(E), CRN(E) 20-1 CR(E), CRI(E), CRN(E) 20-10 - - 16 bar –20°C to +120°C CR(E), CRI(E), CRN(E) 20-12 CR(E), CRI(E), CRN(E) 20-17 - - 25 bar –20°C to +120°C CR(E), CRN(E) 32-1-1 CR(E), CRN(E) 32-7 - - 16 bar –30°C to +120°C CR(E), CRN(E) 32-8-2 CR(E), CRN(E) 32-14 - - 30 bar –30°C to +120°C CR(E), CRN(E) 45-1-1 CR(E), CRN(E) 45-5 - - 16 bar –30°C to +120°C CR(E), CRN(E) 45-6-2 CR, CRN 45-11 - - 30 bar –30°C to +120°C –30°C to +120°C CR, CRN 45-12-2 CR(E), CRN(E) 64-1-1 CR, CRN 64-6-2 CR(E), CRN(E) 90-1-1 CR, CRN 45-13-2 - - 33 bar CR(E), CRN(E) 64-5 - - 16 bar –30°C to +120°C CR, CRN 64-8-1 - - 30 bar –30°C to +120°C CR(E), CRN(E) 90-4 - - 16 bar –30°C to +120°C CR, CRN 90-6 - - 30 bar –30°C to +120°C CR, CRN 90-5-2 Operating range of the shaft seal The operating range of the shaft seal depends on operating pressure, pump type, type of shaft seal and liquid temperature. The following curves apply to clean water and water with anti-freeze liquids. For selecting the right shaft seal, see ’List of pumped liquids’ page 68. 25 H Q Q E H Q Q E HQQE HQQE O-ring (cartridge) (balanced seal), SiC/SiC, EPDM –40°C to +120°C HQQV O-ring (cartridge) (balanced seal), SiC/SiC, FKM –20°C to +90°C HQQV 5 0 -60 -40 -20 0 20 40 60 80 100 120 140 t [°C] • high temperatures up to +180°C, TM03 2107 3705 10 Max. temp. range [°C] • low temperatures down to –40°C or 30 15 Description In case of extreme temperatures, i.e. p [bar] 35 20 Shaft seal see "List of variants - on request" on page 79. Fig. 14 Operating range of standard shaft seals 15 Operating and inlet pressures Maximum inlet pressure The following table shows the maximum permissible inlet pressure. However, the current inlet pressure + the pressure against a closed valve must always be lower than the maximum permissible operating pressure. If the maximum permissible operating pressure is exceeded, the conical bearing in the motor may be damaged and the life of the shaft seal reduced. CR, CRI, CRN 1s 1s-2 › 1s-36 10 bar CR(E), CRI(E), CRN(E) 1 1-2 › 1-36 10 bar CR(E), CRI(E), CRN(E) 3 3-2 3-31 › 3-29 › 3-36 10 bar 15 bar CR(E), CRI(E), CRN(E) 5 5-2 5-18 › 5-16 › 5-36 10 bar 15 bar CR(E), CRI(E), CRN(E) 10 10-1 10-7 › 10-6 › 10-22 › 15-3 › 15-17 › 20-3 › 20-17 › 32-4 › 32-10 › 32-14 › 45-2 › 45-5 › 45-13-2 › 64-2-2 › 64-4-2 › 64-8-1 16 › 90-1 › 90-3-2 › 90-6 This pump is not allowed to start at an inlet pressure of 10 bar, but at an inlet pressure of 16.0 – 10.6 = 5.4 bar. Example 2: The following pump type has been selected: CR 10-2 A-A-A This pump is allowed to start at an inlet pressure of 8.0 bar, as the discharge pressure against a closed valve is only 2.0 bar, which results in an operating pressure of 8.0 + 2.0 = 10.0 bar. On the contrary, the max. operating pressure of this pump is limited to 16.0 bar, as a higher operating pressure will require an inlet pressure of more than 8.0 bar. 4 bar 10 bar 15 bar 4 bar 10 bar 15 bar 4 bar 10 bar 15 bar CR(E), CRN(E) 90 90-1-1 90-2-2 90-3 Discharge pressure against a closed valve: 10.6 bar, see page 41. 8 bar 10 bar CR(E), CRN(E) 64 64-1-1 64-2-1 64-4-1 16 bar 10 bar Discharge pressure against a closed valve: 2.0 bar, see page 73. CR(E), CRN(E) 45 45-1-1 45-3-2 45-6-2 Max. operating pressure: Max. inlet pressure: 8 bar 10 bar CR(E), CRN(E) 32 32-1-1 32-5-2 32-11 Example 1: The following pump type has been selected: CR 5-16 A-A-A Max. operating pressure: Max. inlet pressure: CR(E), CRI(E), CRN(E) 20 20-1 20-4 Examples of operating and inlet pressures The values for operating and inlet pressures shown in the table must not be considered individually but must always be compared, see the following examples: 8 bar 10 bar CR(E), CRI(E), CRN(E) 15 15-1 15-4 CR, CRI, CRN, CRE, CRIE, CRNE 4 bar 10 bar 15 bar 16 bar 8.0 bar In case the inlet or operating pressure exceeds the pressure permitted, see "Lists of variants - on request" page 79. Selection and sizing CR, CRI, CRN, CRE, CRIE, CRNE Selection of pumps Pump efficiency Before determining the best efficiency point, the operation pattern of the pump needs to be identified. Selection of pumps should be based on: • The duty point of the pump (see section 1) • Dimensional data such as pressure loss as a result of height differences, friction loss in the pipework, pump efficiency etc. (see section 2) • Pump materials (see section 3) • Pump connections (see section 4) Is the pump expected to operate at the same duty point, then select a CR pump which is operating at a duty point corresponding with the best efficiency of the pump. p H [MPa] [m] • Shaft seal (see section 5). 2.4 1. Duty point of the pump 2.0 -13 240 p H [MPa] [m] CR, CRE 32 -14 -14-2 -13 240 -9 160 -8 (E) 140 -7 120 -6 (E) 100 -5 80 -4 (E) 60 -3 (E) 40 -2 (E) 20 -1 (E) 0.8 -3-2 -2-2 (E) 0.0 -9 160 -8 (E) 140 -7 120 0 0 0 -8-2 P2 [hp] 1.6 -4-2 -3 (E) -3-2 20 -1 (E) -2-2 (E) -1-1 (E) 24 28 32 36 Q [m³/h] 10 Q [l/s] Best efficiency 2 4 6 8 Eta [%] Eta 80 P2 1/1 P2 2/3 1.0 0.8 0.5 0.0 0.0 40 20 0 0 p [kPa] H [m] 200 20 60 4 8 12 16 20 24 28 32 36 NPSH [m] QH 2900 rpm 1/1 QH 2900 rpm 2/3 15 Q [m³/h] 8 NPSH 6 120 4 0 8 12 2 16 20 4 24 28 6 32 8 P2 [kW] 36 10 Q [m³/h] Q [l/s] Eta 2.0 10 80 Eta [%] 40 5 0 0 4 2 0 0 4 8 12 16 20 24 28 32 36 Q [m³/h] 80 2.4 P2 1/1 1.5 P2 2/3 1.0 0.0 0.0 40 H [m] 200 20 0 4 8 12 16 20 24 28 32 36 Q [m³/h] NPSH [m] QH 2900 rpm 1/1 QH 2900 rpm 2/3 15 8 NPSH 6 120 10 40 5 0 0 Fig. 16 Example of a CR pump’s duty point 20 0 p [kPa] 60 4 2 0 0 4 8 12 16 20 24 28 32 36 Q [m³/h] Fig. 15 Example of a curve chart As the pump is sized on the basis of the highest possible flow, it is important always to have the duty point to the right on the efficiency curve (eta) in order to keep efficiency high when the flow drops. Eta 2. Dimensional data When sizing a pump the following must be taken into account: Q [ m3 /h ] • Required flow and pressure at the draw-off point. • Pressure loss as a result of height differences (Hgeo). TM00 9190 1303 0.5 TM02 7302 3103 0.8 80 20 P2 [kW] 160 0 0 160 16 1.5 -6-2 -4 (E) -2 (E) 12 2.0 -5-2 40 8 2.4 -5 60 4 -9-2 -6 (E) 80 -1-1 (E) -11-2 -10 (E) 100 1.6 -6-2 -12-2 -7-2 P2 [hp] -8-2 -4-2 50 Hz -10-2 0.0 -9-2 -7-2 0.4 -11 200 180 0.4 -11-2 -10 (E) 180 ISO 9906 Annex A -13-2 -12 (E) 220 0.8 Duty point -12-2 -11 TM02 7302 3103 260 1.2 -12 (E) 200 50 Hz ISO 9906 Annex A -13-2 -5-2 280 1.6 CR, CRE 32 -14-2 -10-2 1.6 1.2 2.0 -14 260 220 From a duty point it is possible to select a pump on the basis of the curve charts shown in "Performance curves" from page 29. 2.4 280 Fig. 17 Best efficiency • Friction loss in the pipework (Hf). It may be necessary to account for pressure loss in connection with long pipes, bends or valves, etc. Hf • NPSH value. For calculation of the NPSH value, see "Minimum inlet pressure - NPSH", page 20. Required flow, required pressur Hgeo NPSH TM02 6711 1403 • Best efficiency at the estimated duty point. Fig. 18 Dimensional data 17 Selection and sizing CR, CRI, CRN, CRE, CRIE, CRNE Normally, E-pumps are used in applications characterized by a variable flow. Consequently, it is not possible to select a pump that is constantly operating at optimum efficiency. H Q n n n -------- = -----Q n x x Hn In order to achieve optimum operating economy, the pump should be selected on the basis of the following criteria: Hx H ⎛ n n⎞ 2 n ------- = ⎜ ------⎟ H ⎝ n x⎠ x nn nx • The max. duty point required should be as close as possible to the QH curve of the pump. • The required duty point should be positioned so that P2 is close to the max. point of the QH curve. Eta Q Qx Between the min. and max. performance curve Epumps have an infinite number of performance curves each representing a specific speed. Therefore it may not be possible to select a duty point close to the 100% curve. Qn η n ------- ≈ 1 ηx nx nn H [m] Q Qx Qn nn Pn 0 Q [m³/h] TM01 4916 4803 0 Fig. 19 Min. and max. performance curves In situations where it is not possible to select a duty point close to the 100% curve the below affinity equations can be used. The head (H), the flow (Q) and the input power (P) are all the appropriate variables for the motor speed (n). Note: The approximated formulas apply on condition that the system characteristic remains unchanged for nn and nx and that it is based on the formula H = k x Q2 , where k is a constant. The power equation implies that the pump efficiency is unchanged at the two speeds. In practice this is not quite correct. Finally, it is worth noting that the efficiencies of the frequency converter and the motor must be taken into account if a precise calculation of the power saving resulting from a reduction of the pump speed is wanted. 18 nx Px Min. curve Pn ⎛ n n⎞ 3 ------- = ⎜ ------⎟ Px ⎝ n x⎠ Q TM00 8720 3496 P Max. curve Fig. 20 Affinity equations Legend Hn Hx Qn Qx nn nx ηn ηx Rated head in metres Current head in metres Rated flow in m3/h Current flow in m3/h Rated motor speed in min-1 (nn = 2900 min-1) Current motor speed in min-1 Rated efficiency in % Current efficiency in % WinCAPS and WebCAPS WinCAPS and WebCAPS are both selection programmes offered by Grundfos. The two programmes make it possible to calculate an E-pump’s specific duty point and energy consumption. By entering the dimensional data of the pump, WinCAPS and WebCAPS can calculate the exact duty point and energy comsumption. For further information see page 80 and page 81. Selection and sizing CR, CRI, CRN, CRE, CRIE, CRNE 3. Pump material The material variant (CR(E), CRI(E), CRN(E)) should be selected based of the liquid to be pumped. The product range covers the following three basic types. TM01 2100 1198 • The CR(E), CRI(E) pump types are suitable for clean, non-aggressive liquids such as potable water, oils, etc. • The CRN(E) pump type is suitable for industrial liquids and acids, see” "List of pumped liquids" on page 68 or contact Grundfos. For saline or chloride-containing liquids such as sea water, CRT(E) pumps of titanium are available. Fig. 21 CR pump 4. Pump connections Selection of pump connection depends on the rated pressure and pipework. To meet any requirement the CR(E), CRI(E) and CRN(E) pumps offer a wide range of flexible connections such as: F (DIN) P (PJE) A (oval) TM02 1201 0601 • Oval flange (BSP) • DIN flange • PJE coupling • Clamp coupling • Union (+GF+) Fig. 22 Pump connections • Other connections on request. 5. Shaft seal As standard, the CR(E) range is fitted with a Grundfos shaft seal (cartridge type) suitable for the most common applications. TM02 0538 4800 The following key parameters must be taken into account, when selecting the shaft seal: • Type of pumped liquid • liquid temperature and • maximum pressure. Grundfos offers a wide range of shaft seal variants to meet specific demands see "List of pumped liquids" on page 68. Fig. 23 Shaft seal (cartridge type) Inlet pressure and operating pressure The limit values stated on page 15 and page 16 must not be exceeded as regards ... • maximum inlet pressure and TM02 1204 060 • maximum operating pressure. Fig. 24 Inlet and operating pressure 19 Selection and sizing CR, CRI, CRN, CRE, CRIE, CRNE tm (°C) Hv (m) 190 126 • the liquid temperature is high, 180 100 • the flow is significantly higher than the rated flow, 170 79 160 62 • water is drawn through long pipes, 150 • inlet conditions are poor. 140 45 40 35 30 Hf • water is drawn from depths, To avoid cavitation, make sure that there is a minimum pressure on the suction side of the pump. The maximum suction lift "H" in metres head can be calculated as follows: H Pb NPSH Hv 130 20 110 15 100 12 10 8,0 90 H = pb x 10.2 – NPSH – Hf – Hv – Hs pb = Barometric pressure in bar. (Barometric pressure can be set to 1 bar). In closed systems, pb indicates the system pressure in bar. 80 70 60 50 40 NPSH = Net Positive Suction Head in metres head. (To be read from the NPSH curve at the highest flow the pump will be delivering). Hf Hv Hs = Friction loss in suction pipe in metres head. (At the highest flow the pump will be delivering.) = Vapour pressure in metres head. (To be read from the vapour pressure scale. "Hv" depends on the liquid temperature "Tm"). = Safety margin = minimum 0.5 metres head. If the "H" calculated is positive, the pump can operate at a suction lift of maximum "H" metres head. If the "H" calculated is negative, an inlet pressure of minimum "H" metres head is required. 20 25 120 30 20 10 0 6,0 5,0 4,0 3,0 2,0 1,5 1,0 0,8 0,6 0,4 0,3 0,2 0,1 TM02 7439 3403 Minimum inlet pressure - NPSH Calculation of the inlet pressure "H" is recommended when Fig. 25 Minimum inlet pressure - NPSH Note: In order to avoid cavitation never select a pump with a duty point too far to the right on the NPSH curve. Always check the NPSH value of the pump at the highest possible flow. Selection and sizing CR, CRI, CRN, CRE, CRIE, CRNE How to read the curve charts Pump type, frequency and ISO standard. p H [MPa] [m] 2.4 280 -14 260 -13 240 -12-2 -11 200 -10 (E) 180 -9 160 -8 (E) 140 -7 120 -6 (E) 100 -5 80 -4 (E) 60 -3 (E) 40 -2 (E) 50 Hz ISO 9906 Annex A -13-2 -12 (E) 220 2.0 CR, CRE 32 -14-2 -11-2 QH curve for the individual pump. The bold curves indicate the recommended duty range for best efficiency. -10-2 1.6 -9-2 -8-2 -7-2 -6-2 -5-2 0.8 -4-2 -3-2 0.4 -2-2 (E) The power curves indicate pump input power per stage. Curves are shown for complete (1/1) and for reduceddiameter (2/3) impellers. -1 (E) 20 0.0 -1-1 (E) 0 0 4 0 P2 [hp] 8 12 2 16 20 4 24 28 6 32 8 P2 [kW] 36 Q [m³/h] 10 Q [l/s] Eta [%] Eta 2.0 80 2.4 P2 1/1 1.5 1.6 1.0 0.8 0.5 0.0 0.0 H [m] 200 20 60 40 20 0 0 p [kPa] 160 P2 2/3 4 8 12 16 20 24 28 32 36 Q [m³/h] NPSH [m] QH 2900 rpm 1/1 QH 2900 rpm 2/3 15 8 NPSH 6 120 10 4 40 5 2 0 0 80 The eta curve shows the efficiency of the pump. The eta curve is an average curve of all the pump types shown in the chart. The efficiency of pumps with reduced-diameter impellers is approx. 2% lower than the eta curve shown in the chart. 0 0 4 8 12 16 20 24 28 32 36 The NPSH curve is an average curve for all the variants shown. When sizing the pumps, add a safety margin of at least 0.5 m. Q [m³/h] TM02 7302 3103 Number of stages. First figure: number of stages; second figure: number of reduced-diameter impellers. 1.2 QH curve for each individual impeller. Curves for complete (1/1) and reduced-diameter (2/3) impellers are Fig. 26 How to read the curve charts Guidelines to performance curves • Tolerances to ISO 9906, Annex A, if indicated. • The motors used for the measurements are standard Grundfos motors (MG or MGE). • Measurements have been made with airless water at a temperature of 20°C. • The curves apply to a kinematic viscosity of 2 υ = 1 mm /s (1 cSt). • Due to the risk of overheating, the pumps should not be used at a flow below the minimum flow rate. • The QH curves apply to a rated motor speed of 2900 min-1. All curves are based on current motor speeds. The curve below shows the minimum flow rate as a percentage of the nominal flow rate in relation to the liquid temperature. The dotted line shows a CR pump fitted with an air-cooled top assembly. Qmin [%] 30 CR 20 10 0 40 60 80 100 120 140 160 180 t [°C] TM01 2816 0303 The guidelines below apply to the curves shown on the following pages: Fig. 27 Minimum flow rate 21 Performance curves Technical data CR 1s CR 1s p [kPa] H [m] CR 1s 220 2000 50 Hz -36 ISO 9906 Annex A 200 -33 180 -30 1600 160 -27 -25 140 -23 1200 -21 120 -19 100 -17 -15 800 80 -13 -12 60 -11 -10 -9 -8 400 -7 40 -6 -5 -4 20 -3 -2 0 0 0.0 0.1 0.00 P2 [hp] P2 [kW] 0.04 0.03 0.03 0.2 0.3 0.05 0.4 0.10 0.5 0.6 0.15 0.7 0.8 0.20 0.9 1.0 0.25 Q [m³/h] 0.30 Q [l/s] Eta P2 Eta [%] 30 0.02 20 0.01 10 0.00 0.00 0 p [kPa] H [m] 0.02 0.0 60 6 40 4 20 2 0 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Q [m³/h] NPSH [m] QH 2900 rpm 6 4 NPSH 2 0 0.0 22 0.1 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Q [m³/h] TM02 7424 3605 0.01 Technical data CR 1s Dimensional sketch D2 B2 D1 G 1/2 B1 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 G 1/2 A (Oval) 19 x 24.5 Rp 1 M10 x 40 G 1/2 100 141 250 4 x ø13.5 ø35 180 220 100 145 160 20 20 50 75 ø89 ø100 ø140 22 75 180 220 4 x ø13.5 TM03 1721 2805 G 1/2 Dimensions and weights Pump type Dimension [mm] Motor P2 Oval flange DIN flange [kW] B1 B1+B2 B1 B1+B2 D1 Net weight [kg] D2 Oval DIN flange flange CR 1s-2 0.37 254 445 279 470 141 109 18 23 CR 1s-3 0.37 254 445 279 470 141 109 18 23 CR 1s-4 0.37 272 463 297 488 141 109 19 23 CR 1s-5 0.37 290 481 315 506 141 109 19 24 CR 1s-6 0.37 308 499 333 524 141 109 19 24 CR 1s-7 0.37 326 517 351 542 141 109 20 24 CR 1s-8 0.37 344 535 369 560 141 109 20 25 CR 1s-9 0.37 362 553 387 578 141 109 21 25 CR 1s-10 0.37 380 571 405 596 141 109 21 26 CR 1s-11 0.37 398 589 423 614 141 109 21 26 CR 1s-12 0.37 416 607 441 632 141 109 22 26 CR 1s-13 0.37 434 625 459 650 141 109 22 27 CR 1s-15 0.55 470 661 495 686 141 109 24 28 CR 1s-17 0.55 506 697 531 722 141 109 25 29 CR 1s-19 0.55 542 733 567 758 141 109 25 30 CR 1s-21 0.75 584 815 609 840 141 109 28 32 CR 1s-23 0.75 620 851 645 876 141 109 29 33 CR 1s-25 0.75 656 887 681 912 141 109 29 34 CR 1s-27 1.1 692 923 717 948 141 109 32 37 CR 1s-30 1.1 - - 771 1002 141 109 - 38 CR 1s-33 1.1 - - 825 1056 141 109 - 39 CR 1s-36 1.1 - - 879 1110 141 109 - 41 23 Performance curves CRI, CRN 1s CRI, CRN 1s p [kPa] H [m] CRI, CRN 1s 220 2000 50 Hz -36 ISO 9906 Annex A 200 -33 180 -30 1600 160 -27 -25 140 -23 1200 -21 120 -19 100 -17 -15 800 80 -13 -12 60 -11 -10 -9 -8 400 -7 40 -6 -5 -4 20 -3 -2 0 0 0.0 0.1 0.00 P2 [hp] P2 [kW] 0.04 0.03 0.03 0.2 0.3 0.05 0.4 0.10 0.5 0.6 0.15 0.7 0.8 0.20 0.9 1.0 0.25 Q [m³/h] 0.30 Q [l/s] Eta P2 Eta [%] 30 0.02 20 0.01 10 0.02 0.00 0.00 0 0.0 p [kPa] H [m] 60 6 40 4 20 2 0 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Q [m³/h] NPSH [m] QH 2900 rpm 6 4 NPSH 2 0 0.0 24 0.1 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Q [m³/h] TM02 7425 3605 0.01 Technical data CRI, CRN 1s Dimensional sketch D2 B2 D1 G 1/2 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 ø89 ø105 ø140 75 250 180 210 34 22 ø42.2 50 100 150 210 ø32 ø85 162 ø32 TM03 1722 2805 19 x 27 ø14 4 x ø13 ø59 G 1/2 CA (FlexiClamp) 22 P (PJE) 50 B1 G 1/2 Dimensions and weights Pump type Dimension [mm] Motor P2 PJE/CA DIN flange [kW] B1 B1+B2 B1 B1+B2 B2 Net weight [kg] D1 D2 PJE/CA DIN flange CRI/CRN 1s-2 0.37 257 448 282 473 191 141 109 16 20 CRI/CRN 1s-3 0.37 257 448 282 473 191 141 109 16 21 CRI/CRN 1s-4 0.37 275 466 300 491 191 141 109 17 21 CRI/CRN 1s-5 0.37 293 484 318 509 191 141 109 17 21 CRI/CRN 1s-6 0.37 311 502 336 527 191 141 109 18 22 CRI/CRN 1s-7 0.37 329 520 354 545 191 141 109 18 22 CRI/CRN 1s-8 0.37 347 538 372 563 191 141 109 18 23 CRI/CRN 1s-9 0.37 365 556 390 581 191 141 109 19 23 CRI/CRN 1s-10 0.37 383 574 408 599 191 141 109 19 23 CRI/CRN 1s-11 0.37 401 592 426 617 191 141 109 19 24 CRI/CRN 1s-12 0.37 419 610 444 635 191 141 109 20 24 CRI/CRN 1s-13 0.37 437 628 462 653 191 141 109 20 25 CRI/CRN 1s-15 0.55 473 664 498 689 191 141 109 22 26 CRI/CRN 1s-17 0.55 509 700 534 725 191 141 109 23 27 CRI/CRN 1s-19 0.55 545 736 570 761 191 141 109 23 28 CRI/CRN 1s-21 0.75 587 818 612 843 231 141 109 26 31 CRI/CRN 1s-23 0.75 623 854 648 879 231 141 109 27 31 CRI/CRN 1s-25 0.75 659 890 684 915 231 141 109 28 32 CRI/CRN 1s-27 1.1 695 926 720 951 231 141 109 31 35 CRI/CRN 1s-30 1.1 749 980 774 1005 231 141 109 32 36 CRI/CRN 1s-33 1.1 803 1034 828 1059 231 141 109 33 37 CRI/CRN 1s-36 1.1 857 1088 882 1113 231 141 109 34 39 25 Performance curves CR, CRE 1 CR, CRE 1 p [kPa] H [m] 2000 50 Hz ISO 9906 Annex A -33 200 -30 (E) 180 1600 CR, CRE 1 -36 (E) 220 -27 160 -25 140 1200 -23 (E) -21 120 -19 (E) -17 100 -15 (E) 800 80 -13 -12 -11 (E) -10 60 -9 -8 400 -7 (E) 40 -6 -5 -4 20 -3 (E) -2 0 0 0.0 0.2 0.0 0.4 0.6 0.1 0.8 1.0 0.2 1.2 0.3 1.4 1.6 0.4 1.8 2.0 0.5 2.2 0.6 Q [m³/h] Q [l/s] Eta [%] P2 [kW] Eta 0.06 40 P2 0.03 20 0.00 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Q [m³/h] H [m] NPSH [m] QH 2900 rpm 6 4 2 NPSH 0 0 0.0 26 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Q [m³/h] TM02 7290 3605 3 Technical data CR, CRE 1 Dimensional sketch D2 B2 D1 G 1/2 B1 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 G 1/2 A (Oval) 19 x 24.5 Rp 1 M10 x 40 G 1/2 100 141 250 4 x ø13.5 ø35 20 20 50 75 ø89 ø100 ø140 22 100 145 160 180 220 4 x ø13.5 75 180 220 TM03 1721 2805 G 1/2 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE Net weight [kg] D2 Dimension [mm] Net weight [kg] Oval DIN Oval flange DIN flange D1 flange flange B1 B1+B2 B1 B1+B2 CR 1-2 0.37 254 445 279 470 141 109 18 23 - - - - CR(E) 1-3 0.37 254 445 279 470 141 109 18 23 254 445 279 470 - CR 1-4 0.37 272 463 297 488 141 109 19 23 - - - - - CR 1-5 0.37 290 481 315 506 141 109 19 24 - - - - - CR 1-6 0.37 308 499 333 524 141 109 20 24 - - - - - CR(E) 1-7 0.37 326 517 351 542 141 109 20 25 326 517 351 542 CR 1-8 0.55 344 535 369 560 141 109 21 26 - - - - - CR 1-9 0.55 362 553 387 578 141 109 21 26 - - - - - CR 1-10 0.55 380 571 405 596 141 109 22 26 - - - - - CR(E) 1-11 0.55 398 589 423 614 141 109 22 27 398 589 423 614 CR 1-12 0.75 422 653 447 678 141 109 24 29 - - - - - CR 1-13 0.75 440 671 465 696 141 109 25 29 - - - - - CR(E) 1-15 0.75 476 707 501 732 141 109 26 30 476 707 501 732 CR 1-17 1.1 512 743 537 768 141 109 29 33 - - - - CR(E) 1-19 1.1 548 779 573 804 141 109 29 34 548 779 573 804 CR 1-21 1.1 584 815 609 840 141 109 30 35 - - - - CR(E) 1-23 1.1 620 851 645 876 141 109 31 36 620 851 645 876 CR 1-25 1.5 - - 697 978 178 110 - 44 - - - - - CR 1-27 1.5 - - 733 1014 178 110 - 44 - - - - - CR(E) 1-30 1.5 - - 787 1068 178 110 - 46 - - 787 1068 CR 1-33 2.2 - - 841 1162 178 110 - 47 - - - - CR(E) 1-36 2.2 - - 895 1216 178 110 - 49 - - 895 1216 D2 - - - 19.8 23.9 - - - - - - - - - 21.2 25.3 - - - - - - - - - 24.0 28.1 - - - - - - 28.7 32.7 141 140 141 140 141 140 178 167 - - 178 167 - - - - 30.8 34.9 - - 32.4 36.5 - - - - - - - 51.2 178 167 178 167 - Oval DIN flange flange - 178 167 - - - 58.3 27 Performance curves CRI, CRN, CRIE, CRNE 1 CRI, CRN, CRIE, CRNE 1 p [kPa] H [m] 2000 CRI, CRN 1 CRIE, CRNE 1 -36 (E) 220 -33 200 50 Hz ISO 9906 Annex A -30 (E) 180 1600 -27 160 -25 140 1200 -23 (E) -21 120 -19 (E) -17 100 -15 (E) 800 80 -13 -12 -11 (E) -10 60 -9 -8 400 -7 (E) 40 -6 -5 -4 20 -3 (E) -2 0 0 0.0 0.2 0.0 0.4 0.6 0.1 0.8 1.0 0.2 1.2 0.3 1.4 1.6 0.4 1.8 2.0 0.5 2.2 0.6 Q [m³/h] Q [l/s] Eta [%] P2 [kW] Eta 0.06 40 P2 0.03 20 0.00 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Q [m³/h] H [m] NPSH [m] QH 2900 rpm 6 4 2 NPSH 0 0 0.0 28 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Q [m³/h] TM02 7291 3605 3 Technical data CRI, CRN, CRIE, CRNE 1 Dimensional sketch D2 B2 D1 G 1/2 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 ø89 ø105 ø140 75 250 180 210 34 22 ø42.2 50 100 150 210 ø32 162 ø32 ø85 TM03 1722 2805 19 x 27 ø14 4 x ø13 ø59 G 1/2 CA (FlexiClamp) 22 P (PJE) 50 B1 G 1/2 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 Net weight [kg] D1 D2 PJE/ CA DIN flange Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 Net weight [kg] D1 D2 - - CRI/CRN 1-2 0.37 257 448 282 473 141 109 16 20 - - - - CRI(E)/CRN(E) 1-3 0.37 257 448 282 473 141 109 16 21 257 448 282 473 CRI/CRN 1-4 0.37 275 466 300 491 141 109 17 21 - - - - - CRI/CRN 1-5 0.37 293 484 318 509 141 109 17 21 - - - - - CRI/CRN 1-6 0.37 311 502 336 527 141 109 18 22 - - - - - CRI(E)/CRN(E) 1-7 0.37 329 520 354 545 141 109 18 22 329 520 354 545 CRI/CRN 1-8 0.55 347 538 372 563 141 109 19 23 - - - - - CRI/CRN 1-9 0.55 365 556 390 581 141 109 20 24 - - - - - CRI/CRN 1-10 0.55 383 574 408 599 141 109 20 24 - - - - - CRI(E)/CRN(E) 1-11 0.55 401 592 426 617 141 109 20 24 401 592 426 617 CRI/CRN 1-12 0.75 425 656 450 681 141 109 23 27 - - - - - CRI/CRN 1-13 0.75 443 674 468 699 141 109 23 28 - - - - - CRI(E)/CRIN(E) 1-15 0.75 479 710 504 735 141 109 24 28 479 710 504 735 CRI/CRN 1-17 1.1 515 746 540 771 141 109 27 31 - - - - CRI(E)/CRN(E) 1-19 1.1 551 782 576 807 141 109 28 32 551 782 576 807 CRI/CRN 1-21 1.1 587 818 612 843 141 109 29 33 - - - - CRI(E)/CRN(E) 1-23 1.1 623 854 648 879 141 109 30 34 623 854 648 879 CRI/CRN 1-25 1.5 675 956 700 981 178 110 37 41 - - - - - CRI/CRN 1-27 1.5 711 992 736 1017 178 110 38 42 - - - - - CRI(E)/CRN(E) 1-30 1.5 765 1046 790 1071 178 110 39 43 765 1046 790 1071 CRI/CRN 1-33 2.2 819 1140 844 1165 178 110 41 45 - - - - CRI(E)/CRN(E) 1-36 2.2 873 1194 898 1219 178 110 42 46 873 1194 898 1219 - 20.6 - - - - - - - - - 18.4 22.0 - - - - - - - - - 21.2 24.8 - - - - - - 25.9 29.5 141 140 141 140 178 167 - 178 167 - - - - 28.0 31.6 - - 29.6 33.2 - - - - - - 44.3 47.9 178 167 178 167 - DIN flange 17.0 141 140 - PJE/ CA - 178 167 - - 51.4 55.0 29 Performance curves CR, CRE 3 CR, CRE 3 p [kPa] H [m] 240 CR, CRE 3 -36 (E) 50 Hz ISO 9906 Annex A 220 2000 -33 -31 200 -29 (E) 180 1600 -27 -25 160 -23 (E) 140 1200 -21 -19 (E) 120 -17 800 100 -15 (E) 80 -12 -13 -11 -10 (E) 60 -9 -8 400 -7 (E) 40 -6 -5 (E) -4 20 -3 -2 0 0.0 0.4 0.0 0.8 1.2 0.2 1.6 2.0 0.4 2.4 0.6 2.8 3.2 0.8 3.6 4.0 1.0 4.4 Q [m³/h] 1.2 Q [l/s] Eta [%] P2 [kW] 0.09 60 P2 Eta 0.06 0.03 20 0.00 0 0.0 H [m] 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 Q [m³/h] NPSH [m] QH 2900 rpm 6 3 4 2 2 NPSH 1 0 0 0.0 30 40 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 Q [m³/h] TM02 7292 3605 0 Technical data CR, CRE 3 Dimensional sketch D2 B2 D1 G 1/2 B1 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 G 1/2 A (Oval) 19 x 24.5 Rp 1 M10 x 40 G 1/2 100 141 250 4 x ø13.5 ø35 20 20 50 75 ø89 ø100 ø140 22 100 145 160 180 220 4 x ø13.5 75 180 220 TM03 1721 2805 G 1/2 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE Net weight [kg] D2 Dimension [mm] Net weight [kg] Oval DIN Oval flange DIN flange D1 flange flange B1 B1+B2 B1 B1+B2 D2 Oval DIN flange flange CR 3-2 0.37 254 445 279 470 141 109 18 23 - - - - - - - - CR 3-3 0.37 254 445 279 470 141 109 18 23 - - - - - - - - CR 3-4 0.37 272 463 297 488 141 109 19 23 - - - - - - - - CR(E) 3-5 0.37 290 481 315 506 141 109 19 24 290 481 315 506 20.4 24.5 CR 3-6 0.55 308 499 333 524 141 109 20 25 - - - - CR(E) 3-7 0.55 326 517 351 542 141 109 21 25 326 517 351 542 CR 3-8 0.75 350 581 375 606 141 109 23 27 - - - - - CR 3-9 0.75 368 599 393 624 141 109 23 28 - - - - - CR(E) 3-10 0.75 386 617 411 642 141 109 24 28 386 617 411 642 CR 3-11 1.1 404 635 429 660 141 109 26 31 - - - - - CR 3-12 1.1 422 653 447 678 141 109 26 31 - - - - - CR 3-13 1.1 440 671 465 696 141 109 27 31 - - - - - CR(E) 3-15 1.1 476 707 501 732 141 109 28 32 476 707 501 732 CR 3-17 1.5 528 809 553 834 178 110 36 40 - - - - CR(E) 3-19 1.5 564 845 589 870 178 110 37 41 564 845 589 870 CR 3-21 2.2 600 921 625 946 178 110 38 42 - - - - CR(E) 3-23 2.2 636 957 661 982 178 110 39 43 636 957 661 982 CR 3-25 2.2 - - 697 1018 178 110 - 44 - - - - - CR 3-27 2.2 - - 733 1054 178 110 - 45 - - - - - CR(E) 3-29 2.2 - - 769 1090 178 110 - 46 - - 769 1090 CR 3-31 3.0 - - 809 1144 198 120 - 51 - - - - - CR 3-33 3.0 - - 845 1180 198 120 - 51 - - - - - CR(E) 3-36 3.0 - - 899 1234 198 120 - 53 - - 899 1234 141 140 - - - - 21.8 25.9 - - - - - - 26.9 31.0 - - - - - - - - - 29.6 33.7 141 140 178 167 178 167 - - 178 167 - - - - 42.5 46.6 - - 48.1 52.2 - - - - - - - 54.7 - - - - - - - 62.3 178 167 178 167 198 177 31 Performance curves CRI, CRN, CRIE, CRNE 3 CRI, CRN, CRIE, CRNE 3 p [kPa] H [m] 240 CRI, CRN 3 CRIE, CRNE 3 -36 (E) 220 2000 50 Hz -33 ISO 9906 Annex A -31 200 -29 (E) 180 1600 -27 -25 160 -23 (E) 140 1200 -21 -19 (E) 120 -17 800 100 -15 (E) 80 -12 -13 -11 -10 (E) 60 -9 -8 400 -7 (E) 40 -6 -5 (E) -4 20 -3 -2 0 0.0 0.4 0.0 0.8 1.2 0.2 1.6 2.0 0.4 2.4 0.6 2.8 3.2 0.8 3.6 4.0 1.0 4.4 Q [m³/h] 1.2 Q [l/s] Eta [%] P2 [kW] 0.09 60 P2 Eta 0.06 0.03 20 0.00 0 0.0 H [m] 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 Q [m³/h] NPSH [m] QH 2900 rpm 6 3 4 2 2 NPSH 1 0 0 0.0 32 40 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 Q [m³/h] TM02 7293 3605 0 Technical data CRI, CRN, CRIE, CRNE 3 Dimensional sketch D2 B2 D1 G 1/2 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 ø89 ø105 ø140 75 250 180 210 34 22 ø42.2 50 100 150 210 ø32 162 ø32 ø85 TM03 1722 2805 19 x 27 ø14 4 x ø13 ø59 G 1/2 CA (FlexiClamp) 22 P (PJE) 50 B1 G 1/2 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 Net weight [kg] D1 D2 PJE/ CA DIN flange Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 Net weight [kg] D1 D2 PJE/ CA DIN flange CRI/CRN 3-2 0.37 257 448 282 473 141 109 16 19 - - - - - - - - CRI/CRN 3-3 0.37 257 448 282 473 141 109 16 19 - - - - - - - - CRI/CRN 3-4 0.37 275 466 300 491 141 109 17 19 - - - - - - - - CRI(E)/CRN(E) 3-5 0.37 293 484 318 509 141 109 17 20 293 484 318 509 17.6 21.2 141 140 CRI/CRN 3-6 0.55 311 502 336 527 141 109 18 21 - - - - CRI(E)/CRN(E) 3-7 0.55 329 520 354 545 141 109 19 21 329 520 354 545 CRI/CRN 3-8 0.75 353 584 378 609 141 109 21 24 - - - - - CRI/CRN 3-9 0.75 371 602 396 627 141 109 22 24 - - - - - CRI(E)/CRN(E) 3-10 0.75 389 620 414 645 141 109 22 25 389 620 414 645 CRI/CRN 3-11 1.1 407 638 432 663 141 109 25 27 - - - - - CRI/CRN 3-12 1.1 425 656 450 681 141 109 25 28 - - - - - CRI/CRN 3-13 1.1 443 674 468 699 141 109 26 28 - - - - - CRI(E)/CRN(E) 3-15 1.1 479 710 504 735 141 109 26 29 479 710 504 735 CRI/CRN 3-17 1.5 531 812 556 837 178 110 34 36 - - - - CRI(E)/CRN(E) 3-19 1.5 567 848 592 873 178 110 34 37 567 848 592 873 CRI/CRN 3-21 2.2 603 924 628 949 178 110 36 38 - - - - CRI(E)/CRN(E) 3-23 2.2 639 960 664 985 178 110 37 39 639 960 664 985 CRI/CRN 3-25 2.2 675 996 700 1021 178 110 37 40 - - - - - CRI/CRN 3-27 2.2 711 1032 736 1057 178 110 38 41 - - - - - CRI(E)/CRN(E) 3-29 2.2 747 1068 772 1093 178 110 39 42 747 1068 772 1093 CRI/CRN 3-31 3.0 787 1122 812 1147 198 120 44 47 - - - - - CRI/CRN 3-33 3.0 823 1158 848 1183 198 120 45 47 - - - - - CRI(E)/CRN(E) 3-36 3.0 877 1212 902 1237 198 120 46 49 877 1212 902 1237 - - - - 19.0 22.6 - - - - - - 24.1 27.7 - - - - - - - - - 26.8 30.4 141 140 178 167 178 167 - - 178 167 - - - - 39.7 43.3 - - 45.3 48.9 - - - - - - 47.8 51.4 - - - - - - 55.4 59.0 178 167 178 167 198 177 33 Performance curves CR, CRE 5 CR, CRE 5 p [kPa] H [m] CR, CRE 5 260 2400 50 Hz -36 (E) ISO 9906 Annex A 240 220 2000 -32 200 -29 (E) 180 1600 -26 -24 160 -22 140 1200 -20 (E) -18 120 -16 (E) 100 800 -15 -14 -13 -12 80 -11 -10 (E) 60 -9 -8 (E) 400 -7 -6 40 -5 -4 (E) 20 -3 -2 (E) 0 0 1 0.0 2 3 0.5 4 5 1.0 6 7 1.5 8 2.0 P2 [kW] Q [m³/h] 2.5 Q [l/s] Eta [%] Eta 0.15 60 P2 0.10 40 0.05 20 0.00 0 0 H [m] 1 2 3 4 5 6 7 8 Q [m³/h] NPSH [m] QH 2900 rpm 6 3 4 2 NPSH 2 1 0 0 0 34 1 2 3 4 5 6 7 8 Q [m³/h] TM02 7294 3605 0 Technical data CR, CRE 5 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 D3 G 1/2 A (Oval) 19 x 24.5 Rp 1 M10 x 40 G 1/2 100 141 250 4 x ø13.5 ø35 20 20 50 75 ø89 ø100 ø140 22 100 145 160 180 220 4 x ø13.5 75 180 220 TM03 1723 2805 B1 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE Net weight [kg] D2 D3 Oval flange Dimension [mm] DIN Oval flange flange B1 B1+B2 DIN flange B1 B1+B2 Net weight [kg] D1 CR(E) 5-2 0.37 254 445 279 470 141 109 - 18 23 254 445 279 470 CR 5-3 0.55 281 472 306 497 141 109 - 20 24 - - - - CR(E) 5-4 0.55 308 499 333 524 141 109 - 20 25 308 499 333 524 CR 5-5 0.75 341 572 366 597 141 109 - 22 27 - - - - - CR 5-6 1.1 368 599 393 624 141 109 - 25 30 - - - - - CR 5-7 1.1 395 626 420 651 141 109 - 26 30 - - - - - CR(E) 5-8 1.1 422 653 447 678 141 109 - 26 31 422 653 447 678 CR 5-9 1.5 465 746 490 771 178 110 - 34 38 - - - - CR(E) 5-10 1.5 492 773 517 798 178 110 - 34 39 492 773 517 798 CR 5-11 2.2 519 840 544 865 178 110 - 36 40 - - - - - CR 5-12 2.2 546 867 571 892 178 110 - 36 41 - - - - - CR 5-13 2.2 573 894 598 919 178 110 - 37 41 - - - - CR 5-14 2.2 600 921 625 946 178 110 - 37 42 - - - CR 5-15 2.2 627 948 652 973 178 110 - 38 43 - - CR(E) 5-16 2.2 654 975 679 1000 178 110 - 38 43 654 975 CR 5-18 3.0 712 1047 737 1072 198 120 - 44 48 - - - - CR(E) 5-20 3.0 766 1101 791 1126 198 120 - 45 50 766 1101 791 1126 CR 5-22 4.0 820 1194 845 1217 220 134 - 56 62 - - - - - CR 5-24 4.0 - - 899 1271 220 134 - - 63 - - - - - CR 5-26 4.0 - - 953 1325 220 134 - - 64 - - - - - CR(E) 5-29 4.0 - - 1034 1406 220 134 - - 66 - - 1034 1406 CR 5-32 5.5 - - 1145 1536 220 134 300 - 82 - - - - CR(E) 5-36 5.5 - - 1253 1644 220 134 300 - 84 - - 1253 1644 D2 D3 141 140 - - 19.8 - - - - 21.2 25.3 - - - - - - - - - - - - - 28.8 32.9 - 141 140 178 167 - Oval DIN flange flange - 23.9 - - - - 41.3 45.4 - - - - - - - - - - - - - - - - - - - - - - - - - - 679 1000 - 48.5 52.6 178 167 178 167 - - - - - - 55.1 59.2 - - - - - - - - - - - - - - 76.5 198 177 220 188 - - 220 188 - - - - - 95.5 35 Performance curves CRI, CRN, CRIE, CRNE 5 CRI, CRN, CRIE, CRNE 5 p [kPa] H [m] CRI, CRN 5 CRIE, CRNE 5 260 2400 -36 (E) 240 50 Hz ISO 9906 Annex A 220 2000 -32 200 -29 (E) 180 1600 -26 -24 160 -22 140 1200 -20 (E) -18 120 -16 (E) 100 800 -15 -14 -13 -12 80 -11 -10 (E) -9 60 -8 (E) 400 -7 -6 40 -5 -4 (E) -3 20 -2 (E) 0 0 1 0.0 2 3 0.5 4 5 1.0 6 7 1.5 8 2.0 P2 [kW] Q [m³/h] 2.5 Q [l/s] Eta [%] Eta 0.15 60 P2 0.10 40 0.05 20 0.00 0 0 H [m] 1 2 3 4 5 6 7 8 9Q [m³/h] NPSH [m] QH 2900 rpm 6 3 4 2 2 NPSH 1 0 0 0 36 1 2 3 4 5 6 7 8 9Q [m³/h] TM02 7295 3605 0 Technical data CRI, CRN, CRIE, CRNE 5 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 FGJ (DIN-ANSI-JIS) PN 25 / DN 25/32 ø89 ø105 ø140 75 250 180 210 34 22 ø42.2 50 100 150 210 TM03 1724 2805 19 x 27 ø14 4 x ø13 ø59 G 1/2 CA (FlexiClamp) ø32 22 P (PJE) 50 B1 D3 162 ø32 ø85 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 CRI(E)/CRN(E) 5-2 0.37 257 448 282 473 141 109 - 16 21 257 448 282 473 CRI/CRN 5-3 0.55 284 475 309 500 141 109 - 18 22 - - - - CRI(E)/CRN(E) 5-4 0.55 311 502 336 527 141 109 - 18 22 311 502 336 527 CRI/CRN 5-5 0.75 344 575 369 600 141 109 - 21 25 - - - - - CRI/CRN 5-6 1.1 371 602 396 627 141 109 - 24 28 - - - - - CRI/CRN 5-7 1.1 398 629 423 654 141 109 - 24 28 - - - - - CRI(E)/CRN(E) 5-8 1.1 425 656 450 681 141 109 - 25 29 425 656 450 681 CRI/CRN 5-9 1.5 468 749 493 774 178 110 - 32 36 - - - - CRI(E)/CRN(E) 5-10 1.5 495 776 520 801 178 110 - 32 37 495 776 520 801 CRI/CRN 5-11 2.2 522 843 547 868 178 110 - 34 38 - - - - - CRI/CRN 5-12 2.2 549 870 574 895 178 110 - 34 38 - - - - - CRI/CRN 5-13 2.2 576 897 601 922 178 110 - 35 39 - - - - CRI/CRN 5-14 2.2 603 924 628 949 178 110 - 35 40 - - - CRI/CRN 5-15 2.2 630 951 655 976 178 110 - 36 40 - - CRI(E)/CRN(E) 5-16 2.2 657 978 682 1003 178 110 - 36 41 657 978 CRI/CRN 5-18 3.0 715 1050 740 1075 198 120 - 42 46 - - - - CRI(E)/CRN(E) 5-20 3.0 769 1104 794 1129 198 120 - 43 47 769 1104 794 1129 CRI/CRN 5-22 4.0 823 1195 848 1220 220 134 - 55 59 - - - - - CRI/CRN 5-24 4.0 877 1249 902 1274 220 134 - 56 61 - - - - - CRI/CRN 5-26 4.0 931 1303 956 1328 220 134 - 58 62 - - - - - CRI(E)/CRN(E) 5-29 4.0 1012 1384 1037 1409 220 134 - 59 64 1012 1384 1037 1409 D2 D3 141 140 - - 17.0 - - - - 18.4 22.0 - - - - - - - - - - - - - 26.0 29.6 - 141 140 178 167 - - - 38.5 42.1 - - - - - - - - - - - - - - - - - - - - - - - - - - 682 1003 - 45.7 49.3 5.5 1123 1514 1148 1539 220 134 300 75 79 - - - - CRI(E)/CRN(E) 5-36 5.5 1231 1622 1256 1647 220 134 300 77 81 1231 1622 1256 1647 - 20.6 - CRI/CRN 5-32 - PJE/ DIN CA flange 178 167 178 167 - - - - - - 52.3 55.9 - - - - - - - - - - - - - 69.6 73.2 198 177 220 188 - - 220 188 - - - - 88.6 92.2 37 Performance curves CR, CRE 10 CR, CRE 10 p [kPa] H [m] CR, CRE 10 240 50 Hz -22 (E) ISO 9906 Annex A 220 2000 -20 200 -18 180 1600 -16 (E) 160 -14 140 1200 -12 (E) 120 -10 100 800 -9 (E) -8 80 -7 -6 (E) 60 400 -5 -4 (E) 40 -3 (E) -2 (E) 20 -1 (E) 0 0 1 0.0 2 3 0.5 4 5 1.0 6 1.5 7 8 2.0 9 10 2.5 11 12 3.0 Q [m³/h] 3.5 Q [l/s] P2 [kW] Eta [%] 0.4 Eta 0.3 P2 80 60 0.2 40 0.1 20 0.0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 Q [m³/h] H [m] NPSH [m] 12 6 2900 rpm 8 4 4 2 NPSH 0 0 0 38 1 2 3 4 5 6 7 8 9 10 11 12 Q [m³/h] TM02 7296 3605 0 Technical data CR, CRE 10 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 D3 FJ (DIN-JIS) PN 16-25 / DN 40 B1 A (oval) Rp 1 1/2" G 1/2 ø39 18 x 20.2 4 x ø13.5 20 80 ø114 ø150 20 80 ø110 215 256 130 178 280 M12 x 45 27 4 x ø13.5 130 178 200 Net weight [kg] Dimension [mm] TM03 1725 2805 G 1/2 100 215 256 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE D2 D3 Oval DIN flange flange Oval flange DIN flange B1 B1+B2 B1 B1+B2 D1 Net weight [kg] D2 D3 Oval DIN flange flange CR(E) 10-1 0.37 343 534 343 534 141 109 - 31 34 343 534 343 534 141 140 - 32.9 35.9 CR(E) 10-2 0.75 347 578 347 578 141 109 - 34 36 347 347 347 347 178 167 - 35.2 37.2 CR(E) 10-3 1.1 377 608 377 608 141 109 - 37 39 377 608 377 608 178 167 - 32.9 35.9 CR(E) 10-4 1.5 423 704 423 704 178 110 - 45 47 423 704 423 704 178 167 - 54.5 51.5 CR 10-5 2.2 453 734 453 734 178 110 - 46 49 - - - - - - - CR(E) 10-6 2.2 483 764 483 764 178 110 - 47 50 483 764 483 764 - 57.5 60.5 CR 10-7 3.0 518 853 518 853 198 120 - 52 55 - - - - - - - - - CR 10-8 3.0 548 883 548 883 198 120 - 53 56 - - - - - - - - - CR(E) 10-9 3.0 578 913 578 913 198 120 - 54 57 578 913 578 913 - 63.0 66.0 CR 10-10 4.0 608 980 608 980 220 134 - 66 69 - - - - CR(E) 10-12 4.0 668 1040 668 1040 220 134 - 69 71 668 1040 668 1040 CR 10-14 5.5 760 1151 760 1151 220 134 300 91 94 - - - - CR(E) 10-16 5.5 820 1211 820 1211 220 134 300 93 96 820 1211 820 1211 - - 178 167 198 177 - - 220 188 - - - - - - 78.3 81.3 - 220 188 298 - - 104.9 107.9 - CR 10-18 7.5 - - 880 1271 220 134 300 - 101 - - - - - - - - CR 10-20 7.5 - - 940 1331 220 134 300 - 103 - - - - - - - - - CR(E) 10-22 7.5 - - 1000 1391 220 134 300 - 105 - - 1000 1391 - 116.7 220 188 298 39 Performance curves CRI, CRN, CRIE, CRNE 10 CRI, CRN, CRIE, CRNE 10 p [kPa] H [m] -22 (E) CRI, CRN 10 CRIE, CRNE 10 -20 ISO 9906 Annex A 240 220 2000 50 Hz 200 -18 180 1600 -16 (E) 160 -14 140 1200 -12 (E) 120 -10 100 800 -9 (E) -8 80 -7 -6 (E) 60 400 -5 -4 (E) 40 -3 (E) -2 (E) 20 -1 (E) 0 0 1 0.0 2 3 0.5 4 5 1.0 6 1.5 7 8 2.0 9 10 2.5 11 12 3.0 Q [m³/h] 3.5 Q [l/s] P2 [kW] Eta [%] 0.4 Eta 0.3 P2 80 60 0.2 40 0.1 20 0.0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 Q [m³/h] H [m] NPSH [m] 12 6 2900 rpm 8 4 4 2 NPSH 0 0 0 40 1 2 3 4 5 6 7 8 9 10 11 12 Q [m³/h] TM02 7297 3605 0 Technical data CRI, CRN, CRIE, CRNE 10 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 D3 FGJ (DIN-ANSI-JIS) PN 16-25 / DN 40 G 1/2 26 80 130 200 ø42 ø105 215 248 130 200 280 4 x ø13 TM03 2498 4405 215 248 26 ø60.1 80 130 200 261 ø87 202 80 4 x ø13 26 G 1/2 CA (Flexiclamp) 18.5 x 23.5 ø115 ø150 B1 P (PJE) ø50 215 248 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange CRI(E)/CRN(E) 10-1 0.37 353 544 353 544 141 109 - 28 32 353 544 353 544 141 140 - 29.9 33.9 CRI(E)/CRN(E) 10-2 0.75 357 588 357 588 141 109 - 31 34 357 588 357 588 178 167 - 32.2 35.2 CRI(E)/CRN(E) 10-3 1.1 387 618 387 618 141 109 - 34 38 387 618 387 618 178 167 - 29.9 33.9 CRI(E)/CRN(E) 10-4 1.5 433 714 433 714 178 110 - 42 46 433 714 433 714 178 167 - 48.5 52.5 CRI/CRN 10-5 2.2 463 784 463 784 178 110 - 44 47 - - - - - - - CRI(E)/CRN(E) 10-6 2.2 493 814 493 814 178 110 - 45 48 493 814 493 814 - 55.5 58.5 CRI/CRN 10-7 3.0 528 863 528 863 198 120 - 50 54 - - - - - - - - - CRI/CRN 10-8 3.0 558 893 558 893 198 120 - 51 55 - - - - - - - - - CRI(E)/CRN(E) 10-9 3.0 588 923 588 923 198 120 - 52 56 588 923 588 923 - 61.0 65.0 CRI/CRN 10-10 4.0 618 990 618 990 220 134 - 64 68 - - - - CRI(E)/CRN(E) 10-12 4.0 678 1050 678 1050 220 134 - 66 70 678 1050 678 1050 CRI/CRN 10-14 5.5 770 1161 770 1161 220 134 300 88 92 - - - - CRI(E)/CRN(E) 10-16 5.5 830 1221 830 1221 220 134 300 90 94 830 1221 830 1221 CRI/CRN 10-18 7.5 890 1281 890 1281 220 134 300 96 99 - - - - - - - - - CRI/CRN 10-20 7.5 950 1341 950 1341 220 134 300 98 101 - - - - - - - - - CRI(E)/CRN(E) 10-22 7.5 1010 1401 1010 1401 220 134 300 100 104 1010 1401 1010 1401 - - 178 167 198 177 - - 220 188 - - - - - - 76.3 79.3 - - - 220 188 300 102.9 105.9 220 188 298 110.7 114.7 41 Performance curves CR, CRE 15 CR, CRE 15 p [kPa] H [m] CR, CRE 15 -17 (E) 240 50 Hz ISO 9906 Annex A 220 2000 -14 (E) 200 180 -12 1600 160 -10 140 -9 (E) 1200 120 -8 -7 (E) 100 -6 800 80 -5 (E) -4 60 -3 (E) 400 40 -2 (E) 20 0 0 2 0 4 6 1 8 10 2 12 3 14 16 4 18 20 5 22 6 Q [m³/h] Q [l/s] P2 [kW] Eta [%] 0.8 P2 Eta 0.6 80 60 0.4 40 0.2 20 0.0 0 0 2 4 6 8 10 12 14 16 18 20 22 Q [m³/h] H [m] NPSH [m] 15 6 2900 rpm 10 4 5 2 NPSH 0 0 0 42 2 4 6 8 10 12 14 16 18 20 22 Q [m³/h] TM02 7298 3605 0 -1 (E) Technical data CR, CRE 15 Dimensional sketch D2 B2 D1 G 1/2 D3 130 176 300 A (oval) G 1/2 30 20 ø65 90 ø120 215 256 130 176 300 ø65 215 256 Rp 2" M12 x 45 TM03 1727 2805 20 90 ø125 ø165 G 1/2 90 ø18.1 4 x ø13.5 G 1/2 GJ (ANSI-JIS) 18 x 21.5 20 B1 F (DIN) PN 16-25 / DN 50 ø127 ø165 G 1/2 130 215 256 130 178 200 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE Net weight [kg] D2 D3 Dimension [mm] Oval DIN Oval flange flange flange B1 B1+B2 DIN flange B1 B1+B2 D1 Net weight [kg] D2 D3 Oval DIN flange flange CR(E) 15-1 1.1 400 631 400 631 141 109 - 41 42 400 631 400 631 178 167 - 36.9 37.9 CR(E) 15-2 2.2 415 736 415 736 178 110 - 49 50 415 736 415 736 178 167 - 59.5 60.5 CR(E) 15-3 3.0 465 800 465 800 198 120 - 54 55 465 800 465 800 198 177 - 63.0 64.0 CR 15-4 4.0 510 882 510 882 220 134 - 67 68 - - - - - - - CR(E) 15-5 4.0 555 927 555 927 220 134 - 68 69 555 927 555 927 - 78.3 79.3 CR 15-6 5.5 632 1023 632 1023 220 134 300 90 91 - - - - CR(E) 15-7 5.5 677 1068 677 1068 220 134 300 92 93 677 1068 677 1068 CR 15-8 7.5 - - 722 1113 220 134 300 - 97 - - - - CR(E) 15-9 7.5 - - 767 1158 220 134 300 - 98 - - 767 1158 - - 220 188 - - - 220 188 298 - - - 220 188 298 - - 103.9 104.9 - - - 108.7 - CR 15-10 11.0 - - 889 1388 260 172 350 - 130 - - - - - - - - CR 15-12 11.0 - - 979 1478 260 172 350 - 134 - - - - - - - - - CR(E) 15-14 11.0 - - 1069 1568 260 172 350 - 138 - - 1069 1518 258 359 350 - 188.0 CR(E) 15-17 15.0 - - 1204 1682 320 197 350 - 157 - - 1204 1665 313 377 350 - 190.5 43 Performance curves CRI, CRN, CRIE, CRNE 15 CRI, CRN, CRIE, CRNE 15 p [kPa] H [m] CRI, CRN 15 CRIE, CRNE 15 -17 (E) 240 220 2000 50 Hz ISO 9906 Annex A -14 (E) 200 180 -12 1600 160 -10 140 -9 (E) 1200 120 -8 -7 (E) 100 -6 800 80 -5 (E) -4 60 -3 (E) 400 40 -2 (E) 20 0 0 2 0 4 6 1 8 10 2 12 3 14 16 4 18 20 5 22 6 Q [m³/h] Q [l/s] P2 [kW] Eta [%] 0.8 P2 Eta 0.6 80 60 0.4 40 0.2 20 0.0 0 0 2 4 6 8 10 12 14 16 18 20 22 Q [m³/h] H [m] NPSH [m] 15 6 2900 rpm 10 4 5 2 NPSH 0 0 0 44 2 4 6 8 10 12 14 16 18 20 22 Q [m³/h] TM02 7299 3605 0 -1 (E) Technical data CRI, CRN, CRIE, CRNE 15 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 D3 FGJ (DIN-ANSI-JIS) PN 16-25 / DN50 ø50 130 200 ø65 ø120.5 TM03 1728 2805 ø87 90 26 130 200 300 215 248 26 202 90 26 ø60.1 90 130 200 261 18.5 x 21.8 G 1/2 4 x ø13 G 1/2 CA (Flexiclamp) ø127 ø165 B1 P (PJE) 215 248 215 248 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange CRI(E)/CRN(E) 15-1 1.1 397 628 400 631 141 109 - 34 42 397 628 400 631 178 167 - 29.9 34.9 CRI(E)/CRN(E) 15-2 2.2 413 734 415 736 178 110 - 42 50 413 734 415 736 178 167 - 52.5 57.5 CRI(E)/CRN(E) 15-3 3.0 463 798 465 800 198 120 - 48 55 463 798 465 800 198 177 - 57.0 61.0 CRI/CRN 15-4 4.0 508 880 510 882 220 134 - 60 68 - - - - - - - CRI(E)/CRN(E) 15-5 4.0 553 925 555 927 220 134 - 62 69 553 925 555 927 - 71.3 76.3 CRI/CRN 15-6 5.5 630 1021 632 1023 220 134 300 83 91 - - - - - - CRI(E)/CRN(E) 15-7 5.5 675 1066 677 1068 220 134 300 85 93 675 1066 677 1068 CRI/CRN 15-8 7.5 720 1111 722 1113 220 134 300 89 97 - - - - CRI(E)/CRN(E) 15-9 7.5 765 1156 767 1158 220 134 300 90 98 765 1156 767 1158 CRI/CRN 15-10 11.0 887 1386 889 1388 260 172 350 122 130 - - - - - - - - - CRI/CRN 15-12 11.0 977 1476 979 1478 260 172 350 126 134 - - - - - - - - - CRI(E)/CRN(E) 15-14 11.0 1067 1566 1069 1568 260 172 350 130 138 1067 1516 1069 1518 258 359 350 180.0 185.0 CRI(E)/CRN(E) 15-17 15.0 1202 1680 1204 1682 320 197 350 149 157 1202 1663 1204 1665 313 377 350 181.5 186.5 - - 220 188 - - 220 188 298 96.9 - - - - 100.9 - 220 188 298 100.7 105.7 45 Performance curves CR, CRE 20 CR, CRE 20 p [kPa] H [m] CR, CRE 20 260 2400 -17 (E) 50 Hz ISO 9906 Annex A 240 220 -14 (E) 2000 200 -12 180 1600 160 -10 (E) 140 1200 -8 120 -7 (E) 100 -6 800 80 -5 (E) 60 -4 -3 (E) 400 40 -2 (E) 20 0 0 2 0 4 6 1 8 10 2 12 3 14 16 4 18 20 5 22 24 6 26 28 7 Q [m³/h] 8 Q [l/s] P2 [kW] Eta [%] 1.6 80 1.2 Eta P2 0.8 0.4 60 40 20 0.0 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Q [m³/h] H [m] NPSH [m] 2900 rpm 15 6 10 4 5 2 NPSH 0 0 0 46 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Q [m³/h] TM02 7300 3605 0 -1 (E) Technical data CR, CRE 20 Dimensional sketch D2 B2 D1 G 1/2 D3 TM03 1727 2805 90 ø120 215 256 130 176 300 ø65 215 256 Rp 2" M12 x 45 20 ø65 G 1/2 ø125 ø165 20 90 130 176 300 A (oval) G 1/2 30 90 ø18.1 4 x ø13.5 G 1/2 GJ (ANSI-JIS) 18 x 21.5 20 B1 F (DIN) PN 16-25 / DN 50 ø127 ø165 G 1/2 130 215 256 130 178 200 Dimensions and weights Pump type CR Motor Dimension [mm] P2 [kW] Oval flange DIN flange D1 B1 B1+B2 B1 B1+B2 CRE Net weight [kg] D2 D3 Dimension [mm] Oval DIN Oval flange flange flange B1 B1+B2 DIN flange B1 B1+B2 D1 Net weight [kg] D2 D3 Oval DIN flange flange CR(E) 20-1 1.1 400 631 400 631 141 109 - 41 42 400 631 400 631 178 167 - 36.9 37.9 CR(E) 20-2 2.2 415 736 415 736 178 110 - 49 50 415 736 415 736 178 167 - 65.8 66.8 CR(E) 20-3 4.0 465 837 465 837 220 134 - 65 66 465 837 465 837 220 188 - 75.3 76.3 CR 20-4 5.5 542 933 542 933 220 134 300 87 88 - - - - - - - CR(E) 20-5 5.5 587 978 587 978 220 134 300 89 90 587 978 587 978 100.9 101.9 CR 20-6 7.5 632 1023 632 1023 220 134 300 92 93 - - - - CR(E) 20-7 7.5 677 1068 677 1068 220 134 300 94 95 677 1068 677 1068 CR 20-8 11.0 - - 799 1298 260 172 350 - 127 - - - - CR(E) 20-10 11.0 - - 889 1388 260 172 350 - 130 - - 889 1338 CR 20-12 15.0 - - 979 1457 320 197 350 - 148 - - - - - - CR(E) 20-14 15.0 - - 1069 1547 320 197 350 - 152 - - 1069 1530 313 377 350 - 185.5 CR(E) 20-17 18.5 - - 1204 1722 320 197 350 - 187 - - 1204 1703 313 377 350 - 226.0 - - 220 188 298 - - - 220 188 298 - - - 258 359 350 - - - - - 104.7 105.7 - - - 181.0 47 Performance curves CRI, CRN, CRIE, CRNE 20 CRI, CRN, CRIE, CRNE 20 p [kPa] H [m] 260 2400 CRI, CRN 20 CRIE, CRNE 20 -17 (E) 240 50 Hz ISO 9906 Annex A 220 -14 (E) 2000 200 -12 180 1600 160 -10 (E) 140 1200 -8 120 -7 (E) 100 -6 800 80 -5 (E) 60 -4 -3 (E) 400 40 -2 (E) 20 0 0 2 0 4 6 1 8 10 2 12 3 14 16 4 18 20 5 22 24 6 26 28 7 Q [m³/h] 8 Q [l/s] P2 [kW] Eta [%] 1.6 80 1.2 Eta P2 0.8 0.4 60 40 20 0.0 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Q [m³/h] H [m] NPSH [m] 2900 rpm 15 6 10 4 5 2 NPSH 0 0 0 48 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Q [m³/h] TM02 7301 3605 0 -1 (E) Technical data CRI, CRN, CRIE, CRNE 20 Dimensional sketch D2 B2 D1 G 1/2 G 1/2 D3 FGJ (DIN-ANSI-JIS) PN 16-25 / DN50 ø50 130 200 ø65 ø120.5 TM03 1728 2805 ø87 90 26 130 200 300 215 248 26 202 90 26 ø60.1 90 130 200 261 18.5 x 21.8 G 1/2 4 x ø13 G 1/2 CA (Flexiclamp) ø127 ø165 B1 P (PJE) 215 248 215 248 Dimensions and weights CRI/CRN Pump type Motor P2 [kW] CRIE/CRNE Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange Net weight [kg] Dimension [mm] PJE/CA DIN flange B1 B1+B2 B1 B1+B2 D1 D2 D3 PJE/ DIN CA flange CRI(E)/CRN(E) 20-1 1.1 397 628 397 628 141 109 - 34 39 397 628 397 628 178 167 - 29.9 34.9 CRI(E)/CRN(E) 20-2 2.2 413 734 413 734 178 110 - 42 47 413 734 413 734 178 167 - 52.5 57.5 CRI(E)/CRN(E) 20-3 4.0 463 835 463 835 220 134 - 59 63 463 835 463 835 220 188 - 68.3 73.3 CRI/CRN 20-4 5.5 540 931 540 931 220 134 300 80 85 - - - - - - CRI(E)/CRN(E) 20-5 5.5 585 976 585 976 220 134 300 82 87 585 976 585 976 CRI/CRN 20-6 7.5 630 1021 630 1021 220 134 300 85 90 - - - - CRI(E)/CRN(E) 20-7 7.5 675 1066 675 1066 220 134 300 87 92 675 1066 675 1066 CRI/CRN 20-8 11.0 797 1296 797 1296 260 172 350 119 123 - - - - CRI(E)/CRN(E) 20-10 11.0 887 1386 887 1386 260 172 350 122 127 887 1336 887 1336 - - 220 188 298 93.9 - - - - 220 188 298 97.7 - - - - 98.9 102.7 - 258 359 350 173.0 178.0 CRI/CRN 20-12 15.0 977 1455 977 1455 320 197 350 140 145 - - - - CRI(E)/CRN(E) 20-14 15.0 1067 1545 1067 1545 320 197 350 144 148 1067 1528 1067 1528 313 377 350 177.5 182.5 - - - - - CRI(E)/CRN(E) 20-17 18.5 1202 1720 1202 1720 320 197 350 179 183 1202 1701 1202 1701 313 377 350 218.0 222.0 49 Performance curves CR, CRE 32 CR, CRE 32 p H [MPa] [m] 2.4 280 -14 260 -13 240 -14-2 -12-2 -11 200 50 Hz ISO 9906 Annex A -13-2 -12 (E) 220 2.0 CR, CRE 32 -11-2 -10 (E) -10-2 180 1.6 -9 160 -8 (E) 140 -7 120 -6 (E) 100 -5 -9-2 -8-2 -7-2 1.2 -6-2 -5-2 0.8 80 -4 (E) 60 -3 (E) 40 -2 (E) 20 -1 (E) -4-2 -3-2 0.4 -2-2 (E) 0.0 -1-1 (E) 0 0 4 0 P2 [hp] 8 12 2 16 20 4 24 28 6 32 8 P2 [kW] 36 Q [m³/h] 10 Q [l/s] Eta [%] Eta 2.0 80 2.4 P2 1/1 1.5 1.6 P2 2/3 60 1.0 40 0.8 0.5 20 0.0 0.0 p [kPa] H [m] 200 20 160 0 0 4 8 12 16 20 24 28 32 36 NPSH [m] QH 2900 rpm 1/1 QH 2900 rpm 2/3 15 Q [m³/h] 8 NPSH 6 10 4 40 5 2 0 0 80 0 0 50 4 8 12 16 20 24 28 32 36 Q [m³/h] TM02 7302 3605 120 Technical data CR, CRE 32 Dimensional sketch D2 B2 D1 D3 G 1/2 8 x ø18 G 1/2 105 ø107 ø145 ø185 G 1/2 4 x ø14 30 170 223 320 ø74 240 298 TM01 1749 3298 B1 PN16-25-40/DN65 Dimensions and weights CR Pump type Motor P2 [kW] CRE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight [kg] DIN flange D1 D2 D3 Net weight [kg] B1 B1+B2 B1 B1+B2 CR(E) 32-1-1 1.5 505 786 178 110 135 61 505 786 178 167 135 78.5 CR(E) 32-1 2.2 505 826 178 110 135 62 505 826 178 167 135 89.5 CR(E) 32-2-2 3.0 575 910 198 120 76 575 910 198 177 145 98.0 CR(E) 32-2 4.0 575 947 220 134 158 87 575 947 220 188 160 109.3 CR 32-3-2 5.5 645 1036 220 134 298 107 - - CR(E) 32-3 5.5 645 1036 220 134 298 107 645 1036 - - - - 220 188 298 - - - 119.9 CR 32-4-2 7.5 715 1106 220 134 298 117 - - CR(E) 32-4 7.5 715 1106 220 134 298 117 715 1106 CR 32-5-2 11.0 895 1394 260 172 350 155 - - - - - - CR 32-5 11.0 895 1394 260 172 350 155 - - - - - - CR 32-6-2 11.0 965 1464 260 172 350 158 - - - - - CR(E) 32-6 11.0 965 1464 260 172 350 158 965 1414 CR 32-7-2 15.0 1035 1513 320 197 350 175 - - - - - - CR 32-7 15.0 1035 1513 320 197 350 175 - - - - - - CR 32-8-2 15.0 1105 1583 320 197 350 178 - - - - - CR(E) 32-8 15.0 1105 1583 320 197 350 178 1105 1566 220 188 298 258 359 350 313 377 350 126.7 212.0 236.5 CR 32-9-2 18.5 1175 1693 320 197 350 211 - - - - - - CR 32-9 18.5 1175 1693 320 197 350 211 - - - - - - CR 32-10-2 18.5 1245 1763 320 197 350 214 - - - - - CR(E) 32-10 18.5 1245 1763 320 197 350 214 1245 1744 CR 32-11-2 22.0 1315 1925 363 262 350 250 - - - - - - CR 32-11 22.0 1315 1925 363 262 350 250 - - - - - - CR 32-12-2 22.0 1385 1995 363 262 350 254 - - - - - CR(E) 32-12 22.0 1385 1995 363 262 350 254 1385 1910 CR 32-13-2 30.0 1455 2101 415 300 400 322 - - - - - - CR 32-13 30.0 1455 2101 415 300 400 322 - - - - - - CR 32-14-2 30.0 1525 2171 415 300 400 325 - - - - - - CR 32-14 30.0 1525 2171 415 300 400 325 - - - - - - 313 377 350 351 399 350 280.0 327.0 51 Performance curves CRN, CRNE 32 CRN, CRNE 32 p H [MPa] [m] 280 260 2.4 1.6 -14-2 -13 240 -12-2 -11 200 -11-2 -10 (E) 180 -9 160 -8 (E) 140 -7 50 Hz ISO 9906 Annex A -13-2 -12 (E) 220 2.0 CRN, CRNE 32 -14 -10-2 -9-2 -8-2 -7-2 1.2 120 -6 (E) 100 -5 80 -4 (E) 60 -3 (E) 40 -2 (E) 20 -1 (E) -6-2 -5-2 0.8 -4-2 -3-2 0.4 -2-2 (E) 0.0 -1-1 (E) 0 0 4 0 P2 [hp] 8 12 2 16 20 4 24 28 6 32 8 P2 [kW] 36 Q [m³/h] 10 Q [l/s] Eta [%] Eta 2.0 80 2.4 P2 1/1 1.5 1.6 P2 2/3 60 1.0 40 0.8 0.5 20 0.0 0.0 0 0 p [kPa] H [m] 8 12 16 20 24 28 32 36 15 Q [m³/h] NPSH [m] QH 2900 rpm 1/1 QH 2900 rpm 2/3 20 160 4 8 NPSH 6 10 4 40 5 2 0 0 80 0 0 52 4 8 12 16 20 24 28 32 36 Q [m³/h] TM02 7303 3605 120 Technical data CRN, CRNE 32 Dimensional sketch D2 B2 D1 D3 G 1/2 8 x ø18 G 1/2 105 ø107 ø145 ø185 G 1/2 4 x ø14 30 170 226 320 ø74 240 298 TM01 1750 2203 B1 PN16-25-40/DN65 Dimensions and weights CRN Pump type Motor P2 [kW] CRNE Dimension [mm] Dimension [mm] DIN flange B1 B1+B2 D1 D2 D3 Net weight [kg] DIN flange B1 B1+B2 D1 D2 D3 Net weight [kg] CRN(E) 32-1-1 1.5 505 786 178 110 135 61 505 786 178 167 135 78.5 CRN(E) 32-1 2.2 505 826 178 110 135 62 505 826 178 167 135 89.5 CRN(E) 32-2-2 3.0 575 910 198 120 76 575 910 198 177 145 97.0 CRN(E) 32-2 4.0 575 947 220 134 158 87 575 947 220 188 160 108.3 - CRN 32-3-2 5.5 645 1036 220 134 298 107 - - CRN(E) 32-3 5.5 645 1036 220 134 298 107 645 1036 CRN 32-4-2 7.5 715 1106 220 134 298 117 - - CRN(E) 32-4 7.5 715 1106 220 134 298 117 715 1106 - - - 220 188 298 - - - 220 188 298 118.9 126.7 CRN 32-5-2 11.0 895 1394 260 172 350 155 - - - - - - CRN 32-5 11.0 895 1394 260 172 350 155 - - - - - - CRN 32-6-2 11.0 965 1464 260 172 350 158 - - - - - CRN(E) 32-6 11.0 965 1464 260 172 350 158 965 1414 CRN 32-7-2 15.0 1035 1513 320 197 350 175 - - - - - - CRN 32-7 15.0 1035 1513 320 197 350 175 - - - - - - CRN 32-8-2 15.0 1105 1583 320 197 350 178 - - - - - CRN(E) 32-8 15.0 1105 1583 320 197 350 178 1105 1566 CRN 32-9-2 18.5 1175 1693 320 197 350 211 - - - - - CRN 32-9 18.5 1175 1693 320 197 350 211 - - - - - - CRN 32-10-2 18.5 1245 1763 320 197 350 214 - - - - - - CRN(E) 32-10 18.5 1245 1763 320 197 350 214 1245 1744 CRN 32-11-2 22.0 1315 1925 363 262 350 250 - - - - - - CRN 32-11 22.0 1315 1925 363 262 350 250 - - - - - - CRN 32-12-2 22.0 1385 1995 363 262 350 254 - - - - - CRN(E) 32-12 22.0 1385 1995 363 262 350 254 1385 1910 CRN 32-13-2 30.0 1455 2101 415 300 400 322 - - - - - - CRN 32-13 30.0 1455 2101 415 300 400 322 - - - - - - CRN 32-14-2 30.0 1525 2171 415 300 400 325 - - - - - - CRN 32-14 30.0 1525 2171 415 300 400 325 - - - - - - 258 359 350 313 377 350 313 377 350 351 399 350 212.0 236.5 - 279.0 326.0 53 Performance curves CR, CRE 45 CR, CRE 45 p H [MPa] [m] CR, CRE 45 340 3.2 -13-2 -12 2.4 280 -11 260 -10 ISO 9906 Annex A -12-2 300 2.8 50 Hz 320 -11-2 -10-2 240 -9 -9-2 220 2.0 -8 200 -8-2 -7 180 1.6 -7-2 160 -6 (E) -6-2 140 1.2 0.8 -5 (E) -5-2 120 100 -4 (E) 80 -3 (E) -4-2 -3-2 60 0.4 -2 (E) -2-2 (E) 40 -1 (E) 20 0.0 -1-1 (E) 0 0 5 0 P2 [hp] 10 2 15 20 4 25 6 30 8 35 40 10 45 12 50 14 Q [m³/h] 16 P2 [kW] 4 4 55 Q [l/s] 80 Eta P2 1/1 3 Eta [%] 60 P2 2/3 2 40 1 20 2 0 p H [kPa] [m] 0 0 10 15 20 25 30 35 40 45 50 55 Q [m³/h] QH 2900 rpm 1/1 25 NPSH QH 2900 rpm 2/3 NPSH [m] 5 200 20 150 15 3 100 10 2 50 5 1 0 0 4 0 0 54 5 5 10 15 20 25 30 35 40 45 50 55 Q [m³/h] TM02 7304 3605 0 Technical data CR, CRE 45 Dimensional sketch D2 B2 D1 D3 G 1/2 8 x ø18 G 1/2 140 ø120 ø160 ø200 G 1/2 4 x ø14 ø80 266 331 45 190 248 365 TM01 1751 3203 B1 PN16-25-40/DN80 Dimensions and weights CR Pump type Motor P2 [kW] CRE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight [kg] - 80 559 DIN flange B1 B1+B2 D1 D2 D3 Net weight [kg] B1 B1+B2 CR(E) 45-1-1 3.0 559 894 198 120 894 198 177 145 CR(E) 45-1 4.0 559 931 220 134 158 91 559 931 220 188 160 115.3 CR(E) 45-2-2 5.5 639 1030 220 134 298 108 639 1030 220 188 298 125.9 220 188 298 129.7 104.0 CR(E) 45-2 7.5 639 1030 220 134 298 110 639 1030 CR 45-3-2 11.0 829 1328 260 172 350 149 - - CR(E) 45-3 11.0 829 1328 260 172 350 149 829 1278 CR 45-4-2 15.0 909 1387 320 197 350 169 - - CR(E) 45-4 15.0 909 1387 320 197 350 169 909 1370 CR 45-5-2 18.5 989 1507 320 197 350 204 - - CR(E) 45-5 18.5 989 1507 320 197 350 204 989 1488 CR 45-6-2 22.0 1069 1679 363 262 350 240 - - CR(E) 45-6 22.0 1069 1679 363 262 350 240 1069 1594 CR 45-7-2 30.0 1149 1795 415 300 400 321 - - - - - - CR 45-7 30.0 1149 1795 415 300 400 321 - - - - - - CR 45-8-2 30.0 1229 1875 415 300 400 336 - - - - - - CR 45-8 30.0 1229 1875 415 300 400 336 - - - - - - CR 45-9-2 30.0 1309 1955 415 300 400 341 - - - - - - CR 45-9 37.0 1309 2012 415 300 400 361 - - - - - - CR 45-10-2 37.0 1389 2092 415 300 400 366 - - - - - - CR 45-10 37.0 1389 2092 415 300 400 366 - - - - - - CR 45-11-2 45.0 1469 2178 442 325 450 478 - - - - - - CR 45-11 45.0 1469 2178 442 325 450 478 - - - - - - CR 45-12-2 45.0 1549 2258 442 325 450 483 - - - - - - CR 45-12 45.0 1549 2258 442 325 450 483 - - - - - - CR 45-13-2 45.0 1629 2338 442 325 450 488 - - - - - - - - - 258 359 350 - - - 313 377 350 - - - 313 377 350 - - - 351 399 350 211.0 231.5 271.0 314.0 55 Performance curves CRN, CRNE 45 CRN, CRNE 45 p H [MPa] [m] CRN, CRNE 45 340 3.2 -13-2 -12 2.4 280 -11 260 -10 ISO 9906 Annex A -12-2 300 2.8 50 Hz 320 -11-2 -10-2 240 -9 -9-2 220 2.0 -8 200 -8-2 -7 180 1.6 -7-2 160 -6 (E) -6-2 140 1.2 0.8 -5 (E) -5-2 120 100 -4 (E) 80 -3 (E) -4-2 -3-2 60 0.4 -2 (E) -2-2 (E) 40 -1 (E) 20 0.0 -1-1 (E) 0 0 5 0 P2 [hp] 10 2 15 20 4 25 6 30 8 35 40 10 45 12 50 14 Q [m³/h] 16 P2 [kW] 4 4 55 Q [l/s] 80 Eta P2 1/1 3 Eta [%] 60 P2 2/3 2 40 1 20 2 0 H p [kPa] [m] 0 0 10 15 20 25 30 35 40 45 50 55 Q [m³/h] QH 2900 rpm 1/1 25 NPSH QH 2900 rpm 2/3 NPSH [m] 5 200 20 150 15 3 100 10 2 50 5 1 0 0 4 0 0 56 5 5 10 15 20 25 30 35 40 45 50 55 Q [m³/h] TM02 7305 3605 0 Technical data CRN, CRNE 45 Dimensional sketch D2 B2 D1 D3 G 1/2 8 x ø18 G 1/2 140 ø120 ø160 ø200 G 1/2 4 x ø14 ø80 266 331 45 190 251 365 TM01 1752 3203 B1 PN16-25-40/DN80 Dimensions and weights CRN Pump type Motor P2 [kW] CRNE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight [kg] B1 B1+B2 - 80 559 DIN flange D1 D2 D3 Net weight [kg] B1 B1+B2 CRN(E) 45-1-1 3.0 559 894 198 120 894 198 177 145 CRN(E) 45-1 4.0 559 931 220 134 158 91 559 931 220 188 160 114.3 CRN(E) 45-2-2 5.5 639 1030 220 134 298 108 639 1030 220 188 298 124.9 CRN(E) 45-2 7.5 639 1030 220 148 300 110 639 1030 220 188 298 128.7 CRN 45-3-2 11.0 829 1328 260 172 350 149 - - CRN(E) 45-3 11.0 829 1328 260 172 350 149 829 1278 CRN 45-4-2 15.0 909 1387 320 197 350 169 - - CRN(E) 45-4 15.0 909 1387 320 197 350 169 909 1370 CRN 45-5-2 18.5 989 1507 320 197 350 204 - - CRN(E) 45-5 18.5 989 1507 320 197 350 204 989 1488 CRN 45-6-2 22.0 1069 1679 363 262 350 240 - - CRN(E) 45-6 22.0 1069 1679 363 262 350 240 1069 1594 CRN 45-7-2 30.0 1149 1795 415 300 400 321 - - - - - - CRN 45-7 30.0 1149 1795 415 300 400 321 - - - - - - CRN 45-8-2 30.0 1229 1875 415 300 400 336 - - - - - - CRN 45-8 30.0 1229 1875 415 300 400 336 - - - - - - CRN 45-9-2 30.0 1309 1955 415 300 400 341 - - - - - - CRN 45-9 37.0 1309 2012 415 300 400 361 - - - - - - CRN 45-10-2 37.0 1389 2092 415 300 400 366 - - - - - - CRN 45-10 37.0 1389 2092 415 300 400 366 - - - - - - CRN 45-11-2 45.0 1469 2178 442 325 450 478 - - - - - - CRN 45-11 45.0 1469 2178 442 325 450 478 - - - - - - CRN 45-12-2 45.0 1549 2258 442 325 450 483 - - - - - - CRN 45-12 45.0 1549 2258 442 325 450 483 - - - - - - CRN 45-13-2 45.0 1629 2338 442 325 450 488 - - - - - - - - - 258 359 350 - - - 313 377 350 - - - 313 377 350 - - - 351 399 350 103.0 210.0 231.5 270.0 313.0 57 Performance curves CR, CRE 64 CR, CRE 64 p H [MPa] [m] CR, CRE 64 240 50 Hz -8-1 220 2.0 ISO 9906 Annex A -8-2 -7 200 -7-1 -7-2 180 1.6 -6 -6-1 160 -6-2 -5 140 -5-1 -5-2 1.2 120 -4 (E) -4-1 100 -4-2 (E) -3 0.8 -3-1 (E) 80 -3-2 -2 (E) 60 -2-1 0.4 -2-2 (E) 40 -1 (E) -1-1 (E) 20 0.0 0 0 10 0 P2 [hp] 10 20 30 5 40 50 10 60 15 70 80 20 Q [m³/h] Q [l/s] P2 [kW] 8 Eta Eta [%] 80 8 6 P2 1/1 60 6 4 P2 2/3 40 4 0 2 20 0 0 0 p [kPa] H [m] 300 32 40 50 60 70 80 Q [m³/h] NPSH [m] 8 QH 2900 rpm 2/3 6 16 4 8 2 0 0 0 58 30 NPSH 24 0 20 QH 2900 rpm 1/1 200 100 10 10 20 30 40 50 60 70 80 Q [m³/h] TM02 7306 3605 2 Technical data CR, CRE 64 Dimensional sketch D2 D1 F (DIN) PN25-40/DN100 B2 8 x ø22 ø150 ø190 ø235 G 1/2 4 x ø14 ø100 45 D3 266 331 G 1/2 G 1/2 8 x ø18 140 ø150 ø180 ø220 G 1/2 4 x ø14 ø100 45 190 248 365 266 331 TM01 1753 5197 B1 F (DIN) PN16/DN100 Dimensions and weights CR Pump type Motor P2 [kW] CRE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight DIN flange [kg] D1 B1 B1+B2 D2 D3 Net weight [kg] B1 B1+B2 CR(E) 64-1-1 4.0 561 933 220 134 158 91 561 933 220 188 160 118.3 CR(E) 64-1 5.5 561 952 220 134 298 102 561 952 220 188 298 124.9 220 188 298 132.7 CR(E) 64-2-2 7.5 644 1035 220 134 298 114 644 1035 CR 64-2-1 11.0 754 1253 260 172 350 149 - - CR(E) 64-2 11.0 754 1253 260 172 350 149 754 1203 CR 64-3-2 15.0 836 1314 320 197 350 174 - - CR(E) 64-3-1 15.0 836 1314 320 197 350 174 836 1297 CR 64-3 18.5 836 1354 320 197 350 204 - - CR(E) 64-4-2 18.5 919 1437 320 197 350 214 919 1418 CR 64-4-1 22.0 919 1529 363 262 350 245 - - CR(E) 64-4 22.0 919 1529 363 262 350 245 919 1444 CR 64-5-2 30.0 1001 1647 415 300 400 316 - - - - - - CR 64-5-1 30.0 1001 1647 415 300 400 316 - - - - - - CR 64-5 30.0 1001 1647 415 300 400 316 - - - - - - CR 64-6-2 30.0 1084 1730 415 300 400 336 - - - - - - CR 64-6-1 37.0 1084 1787 415 300 400 356 - - - - - - CR 64-6 37.0 1084 1787 415 300 400 356 - - - - - - CR 64-7-2 37.0 1166 1869 415 300 400 376 - - - - - - CR 64-7-1 37.0 1166 1869 415 300 400 376 - - - - - - CR 64-7 45.0 1166 1875 442 325 450 440 - - - - - - CR 64-8-2 45.0 1249 1958 442 325 450 473 - - - - - - CR 64-8-1 45.0 1249 1958 442 325 450 473 - - - - - - - - - 258 359 350 - - - 313 377 350 - - - 313 377 350 - - - 351 399 350 210.0 231.5 270.0 309.0 59 Performance curves CRN, CRNE 64 CRN, CRNE 64 p H [MPa] [m] CRN, CRNE 64 240 50 Hz -8-1 220 2.0 ISO 9906 Annex A -8-2 -7 200 -7-1 -7-2 180 1.6 -6 -6-1 160 -6-2 -5 140 -5-1 -5-2 1.2 120 -4 (E) -4-1 100 -4-2 (E) -3 0.8 80 -3-1 (E) -3-2 -2 (E) 60 -2-1 0.4 -2-2 (E) 40 -1 (E) -1-1 (E) 20 0.0 0 0 10 0 P2 [hp] 10 20 30 5 40 50 10 60 15 70 20 P2 [kW] 8 Q [m³/h] Q [l/s] Eta Eta [%] 80 8 6 P2 1/1 60 6 4 P2 2/3 40 4 0 2 20 0 0 0 p [kPa] H [m] 300 32 40 50 60 70 Q [m³/h] NPSH [m] 8 QH 2900 rpm 2/3 6 16 4 8 2 0 0 0 60 30 NPSH 24 0 20 QH 2900 rpm 1/1 200 100 10 10 20 30 40 50 60 70 Q [m³/h] TM02 7307 3605 2 Technical data CRN, CRNE 64 Dimensional sketch D2 D1 F (DIN) PN25-40/DN100 B2 8 x ø22 ø150 ø190 ø235 G 1/2 4 x ø14 ø100 45 D3 266 331 G 1/2 G 1/2 8 x ø18 140 ø150 ø180 ø220 G 1/2 4 x ø14 ø100 45 190 251 365 266 331 TM01 1754 0904 B1 F (DIN) PN16/DN100 Dimensions and weights CRN Pump type Motor P2 [kW] CRNE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight DIN flange [kg] D1 B1 B1+B2 D2 D3 Net weight [kg] B1 B1+B2 CRN(E) 64-1-1 4.0 561 933 220 134 158 91 561 933 220 188 160 117.3 CRN(E) 64-1 5.5 561 952 220 134 298 102 561 952 220 188 298 123.9 CRN(E) 64-2-2 7.5 644 1035 220 134 298 114 644 1035 220 188 298 131.7 CRN 64-2-1 11.0 754 1253 260 172 350 149 - - CRN(E) 64-2 11.0 754 1253 260 172 350 149 754 1203 CRN 64-3-2 15.0 836 1314 320 197 350 174 - - CRN(E) 64-3-1 15.0 836 1314 320 197 350 174 836 1297 CRN 64-3 18.5 836 1354 320 197 350 204 - - CRN(E) 64-4-2 18.5 919 1437 320 197 350 214 919 1418 CRN 64-4-1 22.0 919 1529 363 262 350 245 - - CRN(E) 64-4 22.0 919 1529 363 262 350 245 919 1444 CRN 64-5-2 30.0 1001 1647 415 300 400 316 - - - - - - CRN 64-5-1 30.0 1001 1647 415 300 400 316 - - - - - - CRN 64-5 30.0 1001 1647 415 300 400 316 - - - - - - CRN 64-6-2 30.0 1084 1730 415 300 400 336 - - - - - - CRN 64-6-1 37.0 1084 1787 415 300 400 356 - - - - - - CRN 64-6 37.0 1084 1787 415 300 400 356 - - - - - - CRN 64-7-2 37.0 1166 1869 415 300 400 376 - - - - - - CRN 64-7-1 37.0 1166 1869 415 300 400 376 - - - - - - CRN 64-7 45.0 1166 1875 442 325 450 440 - - - - - - CRN 64-8-2 45.0 1249 1958 442 325 450 473 - - - - - - CRN 64-8-1 45.0 1249 1958 442 325 450 473 - - - - - - - - - 258 359 350 - - - 313 377 350 - - - 313 377 350 - - - 351 399 350 209.0 229.5 269.0 308.0 61 Performance curves CR, CRE 90 CR, CRE 90 p H [MPa] [m] CR, CRE 90 210 2.0 -6 200 50 Hz 190 1.8 ISO 9906 Annex A -6-2 180 170 1.6 -5 160 150 1.4 -5-2 140 -4 130 1.2 120 -4-2 110 1.0 -3 (E) 100 90 0.8 0.6 80 -3-2 (E) 70 -2 (E) 60 50 0.4 30 0.2 -2-2 (E) 40 -1 (E) -1-1 (E) 20 10 0.0 0 0 10 0 P2 [hp] 10 20 30 5 40 50 10 60 15 70 80 20 90 100 25 110 30 Q [m³/h] Q [l/s] P2 [kW] Eta [%] 8 80 P2 1/1 Eta P2 2/3 8 6 6 60 4 40 2 20 4 2 0 0 0 0 p [kPa] 10 20 30 40 50 60 70 80 90 100 110 H [m] NPSH [m] 40 NPSH QH 2900 rpm 1/1 300 Q [m³/h] 30 8 6 200 20 4 100 10 2 0 0 0 0 62 10 20 30 40 50 60 70 80 90 100 110 Q [m³/h] TM02 7308 3605 QH 2900 rpm 2/3 Technical data CR, CRE 90 Dimensional sketch D2 D1 F (DIN) PN25-40/DN100 B2 8 x ø22 45 ø156 ø190 ø235 G 1/2 D3 4 x ø14 ø100 280 348 G 1/2 8 x ø18 G 1/2 140 ø156 ø180 ø220 G 1/2 ø100 45 199 261 380 4 x ø14 280 348 TM01 1755 2203 B1 F (DIN) PN16/DN100 Dimensions and weights CR Pump type Motor P2 [kW] CRE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight DIN flange [kg] D1 B1 B1+B2 D2 D3 Net weight [kg] B1 B1+B2 CR(E) 90-1-1 5.5 571 962 220 134 298 107 571 962 220 188 298 CR(E) 90-1 7.5 571 962 220 134 298 109 571 962 220 188 298 133.7 CR(E) 90-2-2 11.0 773 1272 260 172 350 150 773 1222 258 359 350 216.0 CR(E) 90-2 15.0 773 1251 320 197 350 164 773 1234 313 377 350 232.5 CR(E) 90-3-2 18.5 865 1383 320 197 350 214 865 1364 313 377 350 272.0 CR(E) 90-3 22.0 865 1475 363 262 350 245 865 1390 351 399 350 311.0 CR 90-4-2 30.0 957 1603 415 300 400 326 - - - - - - CR 90-4 30.0 957 1603 415 300 400 326 - - - - - - CR 90-5-2 37.0 1049 1752 415 300 400 366 - - - - - - CR 90-5 37.0 1049 1752 415 300 400 366 - - - - - - CR 90-6-2 45.0 1141 1850 442 325 450 437 - - - - - - CR 90-6 45.0 1141 1850 442 325 450 437 - - - - - - 130.9 63 Performance curves CRN, CRNE 90 CRN, CRNE 90 p H [MPa] [m] CRN, CRNE 90 210 2.0 -6 200 50 Hz 190 1.8 ISO 9906 Annex A -6-2 180 170 1.6 -5 160 150 1.4 -5-2 140 -4 130 1.2 120 -4-2 110 1.0 -3 (E) 100 90 0.8 0.6 80 -3-2 (E) 70 -2 (E) 60 50 0.4 30 0.2 -2-2 (E) 40 -1 (E) -1-1 (E) 20 10 0.0 0 0 10 0 P2 [hp] 10 20 30 5 40 50 10 60 15 70 80 20 90 100 25 110 30 Q [m³/h] Q [l/s] P2 [kW] Eta [%] 8 80 P2 1/1 Eta P2 2/3 8 6 60 6 4 40 2 20 4 2 0 0 0 0 p [kPa] 10 20 30 40 50 60 70 80 90 100 110 NPSH [m] 40 NPSH QH 2900 rpm 1/1 300 Q [m³/h] H [m] 30 8 6 200 20 4 100 10 2 0 0 0 0 64 10 20 30 40 50 60 70 80 90 100 110 Q [m³/h] TM02 7309 3605 QH 2900 rpm 2/3 Technical data CRN, CRNE 90 Dimensional sketch D2 D1 F (DIN) PN25-40/DN100 B2 8 x ø22 ø156 ø190 ø235 G 1/2 4 x ø14 ø100 45 D3 280 348 G 1/2 G 1/2 8 x ø18 140 ø156 ø180 ø235 G 1/2 4 x ø14 ø100 45 199 261 380 280 348 TM02 1570 2203 B1 F (DIN) PN16/DN100 Dimensions and weights CRN Pump type Motor P2 [kW] CRNE Dimension [mm] DIN flange D1 D2 Dimension [mm] D3 Net weight DIN flange [kg] D1 B1 B1+B2 D2 D3 Net weight [kg] B1 B1+B2 CRN(E) 90-1-1 5.5 571 962 220 134 298 107 571 962 220 188 298 CRN(E) 90-1 7.5 571 962 220 134 298 109 571 962 220 188 298 133.7 CRN(E) 90-2-2 11.0 773 1272 260 172 350 150 773 1222 258 359 350 216.0 CRN(E) 90-2 15.0 773 1251 320 197 350 164 773 1234 313 377 350 232.5 CRN(E) 90-3-2 18.5 865 1383 320 197 350 214 865 1364 313 377 350 272.0 CRN(E) 90-3 22.0 865 1475 363 262 350 245 865 1390 351 399 350 311.0 CRN 90-4-2 30.0 957 1603 415 300 400 326 - - - - - - CRN 90-4 30.0 957 1603 415 300 400 326 - - - - - - CRN 90-5-2 37.0 1049 1752 415 300 400 366 - - - - - - CRN 90-5 37.0 1049 1752 415 300 400 366 - - - - - - CRN 90-6-2 45.0 1141 1850 442 325 450 437 - - - - - - CRN 90-6 45.0 1141 1850 442 325 450 437 - - - - - - 130.9 65 Motor data CR, CRI, CRN, CRE, CRIE, CRNE Standard motors for CR, CRI, CRN, 50 Hz Motor P2 [kW] Frame size 0.37 71 220-240∆/380-415Y 1.7/1 0.8-0.7 78.5 0.55 71 220-240∆/380-415Y 2.5/1.4 0.8-0.7 80 12-13/6.9-7.5 0.75 80 220-240∆/380-415Y 3.3/1.9 0.81-0.71 81 19.1-20.5/11.0-11.8 1.1 80 220-240∆/380-415Y 4.5/2.6 0.84-0.76 82.8 28.5-31.5/16.3-17.9 1.5 90 220-240∆/380-415Y 5.5/3.2 0.87-0.82 85.5 46.3-50.7/26.8-29.3 2.2 90 380-415∆ 4.5-4.5 0.89-0.87 87.5 37.8-42.3 3.0 100 220-240∆/380-415Y 11-6.4 0.87-0.8 85 88-96.8/50.8-55.7 4.0 112 380-415∆ 8-8 0.88-0.84 89 89.6-98.4 5.5 132 380-415∆ 11.2-11.2 0.88-0.84 90 119.8-131.0 7.5 132 380-415∆ 15.2-15.2 0.87-0.8 89.5 152-168.7 11 160 380-415∆ 21.4-21.4 0.9-0.9 91.4 156.2-171.2 15 160 380-415∆/660-690Y 26.5/15.2 0.9-0.9 91.5 185.5/106.4 18.5 160 380-415∆/660-690Y 31.5/18.4 0.92-0.92 92.5 220.5/128.8 22 180 380-415∆/660-690Y 38.5/22 0.88-0.88 94 277.2/158.4 30 200 380-415∆/660-690Y 53/30.5 0.88-0.88 93.5 371/213.5 37 200 380-415∆/660-690Y 64/37 0.89-0.89 94 460.8/266.4 45 225 380-415∆/660-690Y 77/44.5 0.89-0.89 95 562.1/324.9 I 1/1 [A] Cos ϕ 1/1 η [%] I start -----------I 1⁄1 MG 8.5-9.2/4.9-5.3 TM03 1711 2805 Standard voltage [V] 66 TM03 1710 2805 Siemens Motor data CR, CRI, CRN, CRE, CRIE, CRNE E-motors for CRE, CRIE, CRNE, 50 Hz Motor P2 [kW] Frame size Phase Standard voltage [V] I 1/1 [A] Cos ϕ 1/1 η [%] 0.37 71 1 200-240 2.7-2.5 0.96 68 0.55 71 1 200-240 3.9-3.6 0.96 70 0.75 80 1 200-240 5.1-4.7 0.97 72 1.1 80 1 200-240 7.4-6.8 0.97 73 1.5 90 3 380-480 4 0.74 78 2.2 90 3 380-480 5.35 0.77 80 3.0 100 3 380-480 6.8 0.83 81 4.0 112 3 380-480 9 0.84 82 5.5 132 3 380-480 12 0.86 82 7.5 132 3 380-480 16 0.86 84.5 11 160 3 380-415 21.4 0.93 84 TM03 1712 2805 MGE 15 160 3 380-415 28 0.94 85.5 18.5 160 3 380-415 34 0.95 85.5 22 180 3 380-415 42 0.94 85 TM03 1713 2805 MMGE 67 Pumped liquids CR, CRI, CRN, CRE, CRIE, CRNE Pumped liquids List of pumped liquids Thin, non-explosive liquids, not containing solid particles or fibres. The liquid must not chemically attack the pump materials. A number of typical liquids are listed below. Other pump versions may be applicable, but those stated in the list are considered to be the best choices. When pumping liquids with a density and/or viscosity higher than that of water, oversized motors must be used, if required. The table is intended as a general guide only, and cannot replace actual testing of the pumped liquids and pump materials under specific working conditions. Whether a pump is suitable for a particular liquid depends on a number of factors of which the most important are the chloride content, pH value, temperature and content of chemicals, oils, etc. The list should, however, be applied with some caution as factors such as • concentration of the pumped liquid, • liquid temperature or Please note that aggressive liquids (e.g. sea water and some acids) may attack or dissolve the protective oxide film of the stainless steel and thus cause corrosion. • pressure. may affect the chemical resistance of a specific pump version. The CR(E), CRI(E), CRN(E) pump types are suitable for the following liquids: Safety precautions must be made when pumping dangerous liquids. CR(E), CRI(E) • Non-corrosive liquids. Notes D Often with additives. E Density and/or viscosity differ from that of water. Allow for this when calculating motor output and pump performance. F Pump selection depends on many factors. Contact Grundfos. In systems where all parts in contact with the liquid must be made of high-grade stainless steel. H Risk of chrystallization/precipitation in shaft seal. 1 The pumped liquid highly inflammable. 2 The pumped liquid is combustible. CRT(E) • Saline liquids. 3 Insoluble in water. 4 Low self-ignition point. For liquid transfer, circulation and pressure boosting of cold or hot clean water. CRN(E) • Industrial liquids. • Hypochlorites. • Acids. For saline or chloride-containing liquids such as sea water or oxidizing agents such as hypochlorites, CRT(E) pumps of titanium are available. See separate data booklet on CRT(E). Benzoic acid, C 6H5COOH 32, 45, 64, 90 - 5%, +20°C - - - HQQE HQQE HQQE 1, F 100%, +20°C - - - HQQE HQQE HQQE D, F - HQQE HQQE HQQE - - - E 20%, +30°C - - - HQQE HQQE HQQE - Note Liquid concentration, liquid temperature - 20%, +40°C HQQE HQQE HQQE - - 1, 3, 4, F 100%, +20°C HQBV HQBV HQBV - - - H 0.5%, +20°C - - - HQQV HQQV HQQV - <+120°C HQQE HQQE HQQE - - - F +120°C - +180°C - - - - - - - <+90°C HQQE HQQE HQQE - - - D, E 30%, +50°C HQQE HQQE HQQE - - - Calcium hydroxide, Ca(OH)2 E Saturated solution, +50°C HQQE HQQE HQQE - - - Chloride-containing water F <+30°C, max. 500 ppm - - - HQQE HQQE HQQE Chromic acid, H2CrO4 H 1%, +20°C - - - HQQV HQQV HQQV Boiler water Calcareous water Calcium acetate (as coolant with inhibitor) Ca(CH3COO)2 68 10, 15, 20 Ammonium hydroxide, NH4OH Aviation fuel 1s, 1, 3, 5 Ammonium bicarbonate, NH4HCO3 32, 45, 64, 90 Acetic acid, CH3COOH Acetone, CH3COCH3 Alkaline degreasing agent 10, 15, 20 Pumped liquid CRN(E) 1s, 1, 3, 5 CR(E), CRI(E) Pumped liquids CR, CRI, CRN, CRE, CRIE, CRNE - +120°C - Condensate - 120°C HQQE Copper sulfate, CuSO4 Corn oil E 10%, +50°C - 32, 45, 64, 90 5%, +40°C 10, 15, 20 - H Completely desalinated water (demineralized water) 1s, 1, 3, 5 Liquid concentration, liquid temperature 32, 45, 64, 90 Citric acid, HOC(CH2CO2H)2COOH Note CRN(E) 10, 15, 20 Pumped liquid 1s, 1, 3, 5 CR(E), CRI(E) - - HQQE HQQE HQQE - - HQQE HQQE HQQE HQQE HQQE - - - - - HQQE HQQE HQQE - D, E, 3 100%, +80°C HQQV HQQV HQQV - - 2, 3, 4, F 100%, +20°C HQBV HQBV HQBV - - - - <+120°C HQQE HQQE HQQE - - - Ethanol (ethyl alcohol), C2H5OH 1, F 100%, +20°C HQQE HQQE HQQE - - - Ethylene glycol, HOCH2CH2OH D, E 50%, +50°C HQQE HQQE HQQE - - - Diesel oil Domestic hot water (potable water) Formic acid, HCOOH - 5%, +20°C - - - HQQE HQQE HQQE Glycerine (glycerol), OHCH2CH(OH)CH2OH D, E 50%, +50°C HQQE HQQE HQQE - - - Hydraulic oil (mineral) E, 2, 3 100%, +100°C HQQV HQQV HQQV - - - Hydraulic oil (synthetic) E, 2, 3 100%, +100°C HQQV HQQV HQQV - - - Isopropyl alcohol, CH3CHOHCH3 1, F 100%, +20°C HQQE HQQE HQQE - - - Lactic acid, CH3CH(OH)COOH Linoleic acid, C17H31COOH E, H 10%, +20°C - - - HQQV HQQV HQQV E, 3 100%, +20°C HQQV HQQV HQQV - - - Methanol (methyl alcohol), CH3OH 1, F 100%, +20°C HQQE HQQE HQQE - - - E, 2, 3 100%, +80°C HQQV HQQV HQQV - - - E, H 100%, +80°C HQQV HQQV HQQV - - - F 1%, +20°C - - - HQQE HQQE HQQE - Motor oil Naphthalene, C10H8 Nitric acid, HNO3 Oil-containing water Olive oil Oxalic acid, (COOH)2 Ozone-containing water, (O3) Peanut oil Petrol - <+100°C HQQV HQQV HQQV - - D, E, 3 100%, +80°C HQQV HQQV HQQV - - - H 1%, +20°C - - - HQQE HQQE HQQE - <+100°C - - - HQQE HQQE HQQE D, E, 3 100%, +80°C HQQV HQQV HQQV - - - 1, 3, 4, F 100%, +20°C HQBV HQBV HQBV - - - - - - HQQE HQQE HQQE Phosphoric acid, H3PO4 Propanol, C3H7OH E 20%, +20°C 1, F 100%, +20°C HQQE HQQE HQQE - - - Propylene glycol, CH 3CH(OH)CH2OH D, E 50%, +90°C HQQE HQQE HQQE - - - Potassium carbonate, K2CO3 E 20%, +50°C HQQE HQQE HQQE - - - D, E 30%, +50°C HQQE HQQE HQQE - - - Potassium hydroxide, KOH E 20%, +50°C - - - HQQE HQQE HQQE Potassium permanganate, KMnO4 - 5%, +20°C - - - HQQE HQQE HQQE D, E, 3 100%, +80°C HQQV HQQV HQQV - - - H 0.1%, +20°C - - - HQQE HQQE HQQE Potassium formate (as coolant with inhibitor), KOOCH Rape seed oil Salicylic acid, C6H4(OH)COOH Silicone oil E, 3 100% HQQV HQQV HQQV - - - Sodium bicarbonate, NaHCO3 E 10%, +60°C - - - HQQE HQQE HQQE D, E 30%, <+5°C, pH>8 HQQE HQQE HQQE - - - E 20%, +50°C - - - HQQE HQQE HQQE Sodium hypochlorite, NaOCl F 0.1%, +20°C - - - HQQV HQQV HQQV Sodium nitrate, NaNO3 E 10%, +60°C - - - HQQE HQQE HQQE Sodium phosphate, Na3PO4 E, H 10%, +60°C - - - HQQE HQQE HQQE Sodium sulfate, Na2SO4 Softened water E, H 10%, +60°C - - - HQQE HQQE HQQE - <+120°C - - - HQQE HQQE HQQE D, E, 3 100%, +80°C HQQV HQQV HQQV - - - F 1%, +20°C - - - HQQV HQQV HQQV Sodium chloride (as coolant), NaCl Sodium hydroxide, NaOH Soya oil Sulfuric acid, H2SO4 Sulfurous acid, H2SO3 - 1%, +20°C - - - HQQE HQQE HQQE Unsalted swimming pool water - Approx. 2 ppm free chlorine (Cl2) HQQE HQQE HQQE - - - 69 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Pipework connection For pipework connection, various sets of counter flanges and couplings are available. Counter flanges for CR(E) A set consists of one counter flange, one gasket, bolts and nuts. Counter flange Pump type Rated pressure Pipework connection Product number Threaded 16 bar, EN 1092-2 Rp 1 409901 For welding 25 bar, EN 1092-2 25 mm, nominal 409902 Threaded 16 bar, EN 1092-2 Rp 1¼ 419901 For welding 25 bar, EN 1092-2 32 mm, nominal 419902 Threaded 16 bar, EN 1092-2 Rp 1½ 429902 Threaded 16 bar, EN 1092-2 Rp 2 429904 For welding 25 bar, EN 1092-2 40 mm, nominal 429901 For welding 40 bar, special flange 50 mm, nominal 429903 Threaded 16 bar, EN 1092-2 Rp 2 339903 Threaded 16 bar, special flange Rp 2½ 339904 Threaded 16 bar, special flange Description ø68 ø85 ø115 TM03 2115 3705 CR 1s CR(E) 1 CR(E) 3 CR(E) 5 ø78 ø100 ø140 TM03 0400 3705 ø19 CR 1s CR(E) 1 CR(E) 3 CR(E) 5 ø19 TM03 0401 3705 ø19 ø88 ø110 ø150 CR(E) 10 TM03 0402 3705 ø19 ø102 ø125 ø165 18.5 ø127 TM02 7203 2803 19.5 ø102 ø125 ø165 CR(E) 15 CR(E) 20 Rp 2½ 96509578 TM03 0402 3705 ø19 ø102 ø125 ø165 ø19 122 ø145 ø185 Rp 2½ / 16 bar 70 25 bar, EN 1092-2 50 mm, nominal 339901 For welding 40 bar, special flange 65 mm, nominal 339902 Threaded 16 bar, EN 1092-2 Rp 2½ 349902 Threaded 16 bar, special flange Rp 3 349901 For welding 16 bar, EN 1092-2 65 mm, nominal 349904 For welding 40 bar, DIN 2635 65 mm, nominal 349905 For welding 16 bar, special flange 80 mm, nominal 349903 ø19 ø126 ø145 ø190 Rp 3 / 16 bar ø122 ø145 ø185 40 bar TM03 2116 3705 ø19 For welding CR(E) 32 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Counter flange Pump type TM03 2117 3705 ø19 ø132 ø160 ø200 ø22 ø158 ø180 ø220 16 bar ø162 ø190 ø235 25 bar TM03 2118 3705 ø19 CR(E) 45 CR(E) 64 CR(E) 90 Rated pressure Pipework connection Product number Threaded 16 bar Rp 3 350540 For welding 16 bar 80 mm, nominal 350541 For welding 40 bar 80 mm, nominal 350542 Threaded 16 bar, EN 1092-2 Rp 4 369901 For welding 16 bar, EN 1092-2 100 mm, nominal 369902 For welding 25 bar, EN 1092-2 100 mm, nominal 369905 Description Flange with 20 mm higher collar. With this collar, the installation dimensions of a CR 20 will be identical to those of a CR 32. If a CR 32 is replaced with a CR 20, the base must be raised by 15 mm. 71 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Counter flanges for CRN(E) Counterflanges for CRN(E) pumps are made of stainless steel according to EN 1.4401 (AISI 316). A set consists of one counter flange, one gasket, bolts and nuts. Counter flange Pump type Rated pressure Pipework connection Product number Threaded 16 bar, EN 1092-2 Rp 1 405284 For welding 25 bar, EN 1092-2 25 mm, nominal 405285 Threaded 16 bar, EN 1092-2 Rp 1¼ 415304 For welding 25 bar, EN 1092-2 32 mm, nominal 415305 Threaded 16 bar, EN 1092-2 Rp 1½ 425245 Threaded 16 bar, EN 1092-2 Rp 2 96509570 For welding 25 bar, EN 1092-2 40 mm, nominal 425246 For welding 25 bar, special flange 50 mm, nominal 96509571 Description TM03 2115 3705 ø19 ø68 ø85 ø115 CRI(E), CRN(E) 1s, 1, 3 and 5 ø78 ø100 ø140 TM03 0400 3705 ø88 ø110 ø150 TM03 0401 3705 ø19 CRI(E), CRN(E) 1s, 1, 3 and 5 ø19 ø89 ø110 ø150 TM02 7202 2803 18.5 ø115 21 CRI(E) 10 CRN(E) 10 TM03 0401 3705 ø19 ø88 ø110 ø150 ø89 ø110 ø150 72 TM02 7202 2803 18.5 ø115 21 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Counter flange Pump type Rated pressure Pipework connection Product number Threaded 16 bar, EN 1092-2 Rp 2 335254 Threaded 16 bar, special flange Rp 2½ 96509575 Threaded 16 bar, special flange Description TM00 0402 3705 ø19 ø102 ø125 ø165 ø102 ø125 ø165 TM02 7203 2803 18.5 ø127 19.5 Rp 2½ 96509579 CRI(E) 15, 20 CRN(E) 15, 20 TM03 0402 3705 ø19 ø102 ø125 ø165 For welding 25 bar, EN 1092-2 For welding 25 bar, special flange 50 mm, nominal 335255 ø102 ø125 ø165 ø19 TM00 7203 2803 18.5 ø127 19.5 ø121 ø145 ø121 ø145 16 bar 25 bar/40 bar TM03 2119 3705 ø19 TM03 2117 3705 CRN(E) 45 ø22 ø158 ø180 ø220 16 bar ø162 ø190 ø235 40 bar TM03 2118 3705 ø19 Threaded 16 bar Rp 2½ 349910 Threaded 16 bar, special flange Rp 3 349911 For welding 16 bar 65 mm, nominal 349906 For welding 40 bar 65 mm, nominal 349908 For welding 16 bar, special flange 80 mm, nominal 349907 For welding 25 bar, special flange 80 mm, nominal 349909 Threaded 16 bar Rp 3 350543 For welding 16 bar 80 mm, nominal 350544 For welding 40 bar 80 mm, nominal 350545 Threaded 16 bar Rp 4 369904 For welding 16 bar 100 mm, nominal 369903 For welding 40 bar 100 mm, nominal 369906 CRN(E) 32 ø19 ø132 ø160 ø200 65 mm, nominal 96509573 CRN(E) 64 CRN(E) 90 Flange with 20 mm higher collar. With this collar, the installation dimensions of a CR 20 will be identical to those of a CR 32. If a CR 32 is replaced with a CR 20, the base must be raised by 15 mm. 73 Accessories CR, CRI, CRN, CRE, CRIE, CRNE PJE couplings for CRN(E) Materials in contact with the pumped liquid are made of stainless steel EN 1.4401 (AISI 316) and rubber. A set consists of two coupling halves (Victaulic type 77), one gasket, one pipe stud (for welding or threaded), bolts and nuts. Coupling Pump type Threaded TM00 3808 1094 CRI(E), CRN(E) 1, 3 and 5 CRI(E) CRN(E) 10, 15 and 20 PN Pipework connection 80 bar R 1¼ Pipe stub For welding 80 bar Threaded 70 bar For welding 70 bar Rubber parts Number of Product coupling number sets needed EPDM 2 419911 FKM 2 419905 EPDM 2 419912 FKM 2 419904 EPDM 2 339911 FKM 2 339918 EPDM 2 339910 FKM 2 339917 DN 32 R2 DN 50 FlexiClamp base connections All sets comprise the necessary number of bolts and nuts as well as a gasket/O-ring. A B A B TM02 7369 3303 B TM02 7370 3303 A Pump type TM02 7368 3303 Base connection CRI(E), CRN(E) 1, 3 and 5 CRI(E), CRN(E) 1, 3 and 5 CRI(E), CRN(E) 1, 3 and 5 Connection Oval (cast iron) Rubber parts Number of coupling sets needed Product number Klingersil 1 96449748 Klingersil 1 96449749 Rp 1 Klingersil 2 96449746 Rp 1¼ Klingersil 2 96449747 EPDM 2 96449743 FKM 2 96449744 EPDM 2 96449745 FKM 2 96449900 EPDM 2 405280 FKM 2 405281 EPDM 2 415296 Pipework connection A Rp 1 Rp 1¼ 50 Oval (stainless steel) Union DIN (stainless steel) B G2 DN 25 DN 32 50 75 210 228 250 Rp 1 Rp 1¼ Clamp, threaded pipe stub TM02 7371 3303 B 74 NPT 1 CRI(E), CRN(E) 1, 3 and 5 A 208 50 NPT 1¼ 28.5 - Clamp, pipe stub for welding 37.2 - FKM 2 415297 EPDM 2 405291 405292 FKM 2 EPDM 2 415311 FKM 2 415312 EPDM 2 405282 FKM 2 405283 EPDM 2 415300 FKM 2 415301 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Base connection Pump type Connection B A B TM02 7374 3303 A TM02 7372 3303 Oval (cast iron) Number of coupling sets needed Product number Rp 1¼ Klingersil 2 96498775 Rp 1½ Klingersil 2 96498727 Klingersil 2 96498836 Rp 1¼ Klingersil 2 96498776 Rp 1½ Klingersil 2 96498728 Rp 2 Klingersil 2 96498835 EPDM 2 96500275 FKM 2 96500276 EPDM 2 96498840 FKM 2 96500119 EPDM 2 96500263 FKM 2 96500264 EPDM 2 96500265 FKM 2 96500266 EPDM 2 96500257 FKM 2 96500269 EPDM 2 425238 FKM 2 425239 EPDM 2 335241 FKM 2 335242 EPDM 2 96508600 FKM 2 96508601 EPDM 2 425242 FKM 2 425243 EPDM 2 335251 FKM 2 335252 A B Rp 2 CRI(E) 10 CRN(E) 10 80 Oval (stainless steel) CRI(E) 10 CRN(E) 10 Rubber parts Pipework connection Union G 2¾ 80 260 288 FGJ (cast iron) DN 40 FGJ (stainless steel) CRI(E) 10 CRN(E) 10 B 316 FGJ (cast iron) TM02 7373 3303 A 80 DN 50 FGJ (stainless steel) Rp 1½ 259 Clamp, threaded pipe stub CRI(E) 10 CRN(E) 10 Rp 2 Rp 2½ 80 346 A TM02 7375 3303 B 48.3 (DN 40) - Clamp, pipe stub for welding 60.3 (DN 50) - 75 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Base connection Pump type Connection B A B TM02 7374 3303 A TM02 7372 3303 Oval (cast iron) CRI(E) 15, 20 CRN(E) 15,20 Number of coupling sets needed Product number Rp 1¼ Klingersil 2 96498775 Rp 1½ Klingersil 2 96498727 Klingersil 2 96498836 Rp 1¼ Klingersil 2 96498776 Rp 1½ Klingersil 2 96498728 Rp 2 Klingersil 2 96498835 EPDM 2 96500275 FKM 2 96500276 EPDM 2 96498840 FKM 2 96500119 EPDM 2 96500263 FKM 2 96500264 EPDM 2 96500265 FKM 2 96500266 EPDM 2 96500267 FKM 2 96500269 EPDM 2 425238 FKM 2 425239 EPDM 2 335241 FKM 2 335242 EPDM 2 96508600 FKM 2 96508601 EPDM 2 425242 FKM 2 425243 EPDM 2 335251 FKM 2 335252 A B Rp 2 90 Oval (stainless steel) CRI(E) 15, 20 CRN(E) 15,20 Rubber parts Pipework connection Union G 2¾ 90 260 288 FGJ (cast iron) A B TM02 7373 3303 DN 40 CRI(E) 15, 20 CRN(E) 15, 20 FGJ (stainless steel) 90 334 FGJ (cast iron) DN 50 FGJ (stainless steel) Rp 1½ 259 Clamp, threaded pipe stub CRI(E) 15, 20 CRN(E) 15, 20 A Rp 2 Rp 2½ 90 346 TM02 7375 3303 B 76 48.3 (DN 40) - Clamp, pipe stub for welding 60.3 (DN 50) - Accessories CR, CRI, CRN, CRE, CRIE, CRNE Potentiometer for CRE, CRIE, CRNE Remote control, R100 Potentiometer for setpoint setting and start/stop of the CRE, CRIE, CRNE pump. R100 is used for wireless communication with the CRE, CRIE, CRNE pump. The communication takes place by means of infrared light. Product Product number External potentiometer with cabinet for wall mounting Product 625468 G10-LON interface for CRE, CRIE, CRNE EMC-filter required for installation of 11 to 22 kW Epumps in residential areas. Product Product number EMC-filter (11 kW) EMC-filter (15 kW) 96478309 EMC-filter (18.5 kW) Product number G10-LON interface 625333 EMC-filter for CRE, CRIE, CRNE The G10-LON interface is used in connection with data transmission between a Locally Operating Network (LON) and electronically controlled Grundfos pumps applying the Grundfos bus-protocol GENIbus. Product Product number R100 EMC-filter (22 kW) 00605726 LiqTec for CR(E), CRI(E) and CRN(E) A dry-running protection device, the LiqTec protects pump and process against dry-running and temperatures exceeding 130°C ±5°C. Connected to the motor PTC sensor, LiqTec also monitors motor temperature. LiqTec is prepared for DIN rail mounting in control cabinet. Enclosure class: IP X0. TM03 2108 3705 CR(E) CRI(E) CRN(E) 90 mm Extension cable 15 m Product number 200-240 - 96556429 80-130 - 96556430 Pump type Voltage [V] 116 mm Dry-running protection - LiqTec - Sensor ½" - Cable 5 m - 96443676 77 Accessories CR, CRI, CRN, CRE, CRIE, CRNE Sensors for CRE, CRIE, CRNE Accessory Type Flowmeter SITRANS FM MAGFLO MAG 5100 W Supplier Measuring range Product number Siemens 1-5m (DN 25) ID8285 Flowmeter SITRANS FM MAGFLO MAG 5100 W Siemens 3 - 10 m3 (DN 40) ID8286 3 3 Flowmeter SITRANS FM MAGFLO MAG 5100 W Siemens 6 - 30 m (DN 65) ID8287 Flowmeter SITRANS FM MAGFLO MAG 5100 W Siemens 20 - 75 m3 (DN 100) ID8288 Temperature sensor TTA (0) 25 Carlo Gavazzi 0°C to +25°C 96432591 Temperature sensor TTA (-25) 25 Carlo Gavazzi –25°C to +25°C 96430194 Temperature sensor TTA (50) 100 Carlo Gavazzi +50°C to +100°C 96432592 Temperature sensor TTA (0) 150 Carlo Gavazzi 0°C to +150°C 96430195 Protecting tube ø9 x 50 mm Carlo Gavazzi 96430201 Protecting tube ø9 x 100 mm Carlo Gavazzi 96430202 Accessory for temperature sensor. All with ½ RG connection Cutting ring bush Carlo Gavazzi Temperature sensor, ambient temperature WR 52 tmg (DK: Plesner) –50°C to +50°C 96430203 ID8295 Differential temperature sensor ETSD Honsberg 0°C to +20°C 96409362 Differential temperature sensor ETSD Honsberg 0°C to +50°C 96409363 Note: All sensors have 4-20 mA signal output. Danfoss pressure sensor kits for CRE, CRIE, CRNE 1, 3, 5, 10, 15, 20, 32, 45, 64 and 90 Kit consisting of • Danfoss pressure transmitter, type MBS 3000, with 2 m screened cable Connection: G ½ A (DIN 16288 - B6kt) • 5 cable clips (black) • Instruction manual PT (00 40 02 12) Pressure range Temperature range 0 - 4 bar 96428014 0 - 6 bar 0 - 10 bar Product number 96428015 –40°C to +85°C 96428016 0 - 16 bar 96428017 0 - 25 bar 96428018 HUBA differential pressure sensor kit Kit consisting of.. • • • • • • • • • 78 1 1 1 2 1 1 2 2 5 sensor incl. 1.5 m screened cable (7/16" connections) original HUBA bracket (for wall mounting) Grundfos bracket (for mounting on motor) M4 screws for mounting of sensor on bracket M6 screw (self-cutting) for mounting on MGE 90/100 M8 screw (self-cutting) for mounting on MGE 112/132 capillary tubes (short/long) brackets (1/4" - 7/16") cable clips (black) Pressure range Product number 0 - 0.6 bar 485450 0 - 1 bar 485441 0 - 1.6 bar 485442 0 - 2.5 bar 485443 0 - 4 bar 485444 0 - 6 bar 485445 Variants Lists of variants - on request Although the Grundfos CR(E), CRI(E), CRN(E) product range offers a number of pumps for different applications, customers require specific pump solutions to satisfy their needs. Below please find the range of options available for customizing the CR(E) pumps to meet the customers’ demands. Contact Grundfos for further information or for requests other than the ones mentioned below. CR, CRI, CRN, CRE, CRIE, CRNE Pumps Variant Description Horizontally mounted pump For safety or height reasons, certain applications, for instance on ships, require the pump to be mounted in the horizontal position. For easy installation the pump is equipped with brackets that support motor and pump. Low-temperature pump Exposed to temperatures down to –40°C, coolant pumps may require neck-rings with a different diameter in order to prevent impeller drag. High-speed pump up to 47 bar For high-pressure applications, Grundfos offers a unique pump capable of generating up to 47 bar. The pump is equipped with a high-speed motor, type MGE. The direction of rotation is the opposite of that of standard pumps, and the chamber stack is turned upside-down, as a result of which the pumped liquid flows in the opposite direction. For high-pressure applications,Grundfos offers a unique double pump system capable of generating a pressure of up to 47 bar pressure. Motors Variant Description ATEX motor For operation in hazardous atmospheres, explosion-proof or dust-ignition-proof motors may be required. High-pressure pump up to 47 bar Motor with anticondensation heating unit For operation in humid environments motors with built-in anti-condensation heating unit may be required. Recommended for boiler-feed applications Low-NPSH pump where cavitation may occur due to poor inlet (improved suction) conditions. Grundfos offers motors with built-in bimetallic Motor with thermal thermal switches or temperature-controlled protection PTC sensors (thermistors) incorporated in the motor windings. Oversize motor 4-pole motor Ambient temperatures above 40°C or installation at altitudes of more than 1000 metres above sea level require the use of an oversize motor (i.e. derating). The bearing flange is suitable for applications where the inlet pressure is higher than the Pump with bearing maximum pressure recommended. The bearing flange increases the life of motor flange bearings. (Recommended for standard motors.) Belt-driven pump Belt-driven pumps designed to operate in places with limited space or where no electrical power is available. Pump for pharmaceutical and biotechnological applications CRN(E) pumps designed for applications requiring the sterilization and CIP capability of pipes, valves and pumps. (CIP = Cleaning-InPlace.) Grundfos offers 4-pole standard motors. Shaft seals Variant Description Shaft seal with FFKM O-ring material Shaft seals with FFKM or FXM O-ring material are recommended for applications where the pumped liquid may damage the standard Oring material. Seal with flush, quench seal Recommended for applications involving crystallizing, hardening or sticky liquids. Air-cooled shaft seal system Recommended for applications involving extremely high temperatures. No conventional mechanical shaft seal can withstand liquid temperatures of up to 180°C for any length of time. For such applications, Grundfos’ unique aircooled shaft seal system is recommended. In order to ensure a low liquid temperature around the standard shaft seal, the pump is fitted with a special air-cooled shaft seal chamber. No separate cooling is required. Double seal with pressure chamber Recommended for applications involving poisonous or explosive liquids. Protects the surrounding environment and the people working in the vicinity of the pump. Consists of two seals mounted in a "back-toback" arrangement inside a separate pressure seal chamber. As the pressure in the chamber is higher than the pump pressure, leakage is prevented. A dosing pump or a special pressure-intensifier generates the seal chamber pressure. CR MAGdrive Magnetically driven pumps for industrial applications. Key applications are industrial processes invoving the handling of aggressive, environmental, dangerous or volatile liquids, e.g. organic compounds, solvents, etc. Connections and other variants Variant Description Pipe connections In addition to the wide range of standard flange connections, a 16 bar DIN standard clamping flange is available. Customized flanges are available according to specifications. TriClamp connection TriClamp connections are of a hygienic design with a sanitary coupling for use in the pharmaceutical and food industry. Electropolished pump To substantially reduce the risk of corrosion of the materials. For use in the pharmacentical/food industry. 79 Further product documentation CR, CRI, CRN, CRE, CRIE, CRNE In addition to this printed data booklet, Grundfos offers the following sources of product documentation. • WinCAPS • WebCAPS. WinCAPS WinCAPS is a Windows-based Computer Aided Product Selection program containing information on more than 90,000 Grundfos products. cd-wincaps Available on CD-ROM in more than 15 languages, WinCAPS offers • detailed technical information • selection of the optimum pump solution Fig. 28 WinCAPS CD-ROM • dimensional drawings of each pump • detailed service documentation • installation and operating instructions • wiring diagrams of each pump. Click Sizing and select the most suitable pump for your application. WinCAPS Click Catalogue and select a product from the extensive product catalogue. Fig. 29 WinCAPS 80 Further product documentation CR, CRI, CRN, CRE, CRIE, CRNE WebCAPS WebCAPS is a Web-based Compute Aided Product Selection program and a web-version of WinCAPS. WebCAPS is accessible on Grundfos’ homepage, www.grundfos.com, and offers • detailed technical information • dimensional drawings of each pump • wiring diagrams of each pump. Click Service to find information on service kits and spare parts. Click Search and select a product from the extensive product catalogue. Click Replacement and select the right replacement pump based on the current installation. Click on Sizing and select the most suitable pump for your application. Click CAD drawings to select and download CAD drawings in: –.stp –.dxf –.dwg Being a registered user click Log in to: – save your settings – define and save your own units – save personalised information. Click Settings and select your preferred options. WebCAPS_English Click Catalogue and select a product from the extensive product catalogue. Click Literature to select and download Grundfos documentation by browsing the product ranges or performing a specific search. Literature includes: – data booklets – installation and operating instructions – service etc. Fig. 30 WebCAPS 81 Further product documentation 82 CR, CRI, CRN, CRE, CRIE, CRNE Further product documentation CR, CRI, CRN, CRE, CRIE, CRNE 83 Being responsible is our foundation Thinking ahead makes it possible Innovation is the essence V7023751 1105 Repl. V7023751 0105 GB GRUNDFOS A/S . DK-8850 Bjerringbro . Denmark Telephone: +45 87 50 14 00 www.grundfos.com Subject to alterations.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 84 Page Mode : UseOutlines XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:9d845b39-3792-4d2b-b880-392da5bbe636 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2005:11:25 10:44:55Z Creator Tool : FrameMaker 7.0 Modify Date : 2005:11:25 10:44:55Z Document ID : uuid:d8e29da1-b051-4005-ba24-828e526cb13b Format : application/pdf Title : untitled Creator : FrameMaker 7.0EXIF Metadata provided by EXIF.tools