GENERAL DESCRIPTION HUGE Reference Manual For The Nuvoton N76E003 Microcontroller

User Manual:

Open the PDF directly: View PDF .
Page Count: 261 [warning: Documents this large are best viewed by clicking the View PDF Link!]

Scroll down to view the document on your mobile browser.

1. General Description
2. Features
3. Block Diagram
4. Pin Configuration
5. Memory Organization
- 5.1 Program Memory
- 5.2 Data Memory
- 5.3 On-Chip XRAM
- 5.4 Non-Volatile Data Storage
6. Special Function Register (SFR)
- 6.1 ALL SFR DESCRIPTION
7. I/O Port Structure and Operation
- 7.1 Quasi-Bidirectional Mode
- 7.2 Push-Pull Mode
- 7.3 Input-Only Mode
- 7.4 Open-Drain Mode
- 7.5 Read-Modify-Write Instructions
- 7.6 Control Registers of I/O Ports
8. Timer/Counter 0 and 1
- 8.1 Mode 0 (13-Bit Timer)
- 8.2 Mode 1 (16-Bit Timer)
- 8.3 Mode 2 (8-Bit Auto-Reload Timer)
- 8.4 Mode 3 (Two Separate 8-Bit Timers)
9. Timer 2 and Input Capture
- 9.1 Auto-Reload Mode
- 9.2 Compare Mode
- 9.3 Input Capture Module
10. Timer 3
11. Watchdog Timer (WDT)
- 11.1 Time-Out Reset Timer
- 11.2 General Purpose Timer
12. Self Wake-Up Timer (WKT)
13. Serial Port (UART)
- 13.1 Mode 0
- 13.2 Mode 1
- 13.3 Mode 2
- 13.4 Mode 3
- 13.5 Baud Rate
- 13.6 Framing Error Detection
- 13.7 Multiprocessor Communication
- 13.8 Automatic Address Recognition
14. Serial Peripheral Interface (SPI)
- 14.1 Functional Description
- 14.2 Operating Modes
  - 14.2.1 Master Mode
  - 14.2.2 Slave Mode
- 14.3 Clock Formats and Data Transfer
- 14.4 Slave Select Pin Configuration
- 14.5 Mode Fault Detection
- 14.6 Write Collision Error
- 14.7 Overrun Error
- 14.8 SPI Interrupt
15. Inter-Integrated Circuit (I2C)
- 15.1 Functional Description
- 15.2 Control Registers of I2C
- 15.3 Operating Modes
- 15.4 Typical Structure of I2C Interrupt Service Routine
- 15.5 I2C Time-Out
- 15.6 I2C Interrupt
16. Pin Interrupt
17. Pulse Width Modulated (PWM)
- 17.1 Functional Description
- 17.2 PWM Interrupt
18. 12-bit Analog-To-Digital Converter (ADC)
- 18.1 Functional Description
- 18.2 Control Registers of ADC
19. Timed Access Protection (TA)
20. Interrupt System
- 20.1 Interrupt Overview
- 20.2 Enabling Interrupts
- 20.3 Interrupt Priorities
- 20.4 Interrupt Service
- 20.5 Interrupt Latency
- 20.6 External Interrupt Pins
21. In-Application-Programming (IAP)
- 21.1 IAP Commands
- 21.2 IAP User Guide
- 21.3 Using Flash Memory as Data Storage
- 21.4 In-System-Programming (ISP)
22. Power Management
- 22.1 Power-Down Mode
23. Clock System
- 23.1 System Clock Sources
  - 23.1.1 Internal Oscillators
- 23.2 System Clock Switching
- 23.3 System Clock Divider
- 23.4 System Clock Output
24. Power Monitoring
- 24.1 Power-On Reset (POR)
- 24.2 Brown-Out Detection (BOD)
25. Reset
- 25.1 Power-On Reset
- 25.2 Brown-Out Reset
- 25.3 External Reset and Hard Fault Reset
- 25.4 Hard Fault Reset
- 25.5 Watchdog Timer Reset
- 25.6 Software Reset
- 25.7 Boot Select
- 25.8 Reset State
26. Auxiliary Features
- 26.1 Dual DPTRs
- 26.2 96-bit UID
27. On-Chip-Debugger (OCD)
- 27.1 Functional Description
- 27.2 Limitation of OCD
28. CONFIG Bytes
29. In-Circuit-Programming (ICP)
30. Instruction Set
31. Electrical Characteristics
- 31.1 Absolute Maximum Ratings
- 31.2 D.C. Electrical Characteristics
- 31.3 A.C. Electrical Characteristics
- 31.4 Analog Electrical Characteristics
- 31.5 ESD Characteristics
- 31.6 EFT Characteristics
- 31.7 Flash DC Electrical Characteristics
32. Package Dimensions
- 32.1 20-pin TSSOP - 4.4 X 6.5 mm
- 32.2 20-pin QFN – 3.0 X 3.0 mm
33. Document Revision History

Navigation menu