IS CS1718RK

: Is-Cs1718Rk is-cs1718rk images 708 p4dbimg

Open the PDF directly: View PDF .
Page Count: 3

Download
Open PDF In Browser	View PDF

Assembly Instruction Sheet #IS-CS1718RK
For Style CS1718RK

6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com

Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection.
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (4) B10 Candelabra Base 60W bulb Maximum.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Note: This fixture can be mounted as hanging or semi-flush. Refer to respective installation steps for installations.

Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

Package Contents

STEP 2 - Install Canopy Chain Loop and Nipple

Fixture
A Loop
x1

Center
B Column
x1

D

Nipple
x1

Socket
C Assembly
x1

E

Cap
x1

Hardware Contents
AA

BB

Crossbar
x1

F

Finial
x1

GG Fixture Chain
x1
HH

Quick Link
x2
Ceiling
II Canopy
x1

Lock Washer
x2
CC

Big Hex Nut
x2

DD

Nipple
x1

JJ
KK

Canopy
EE Chain Loop
x1

LL

Mounting Screw
x2

Small Lock Washer
x2
Small Hex Nut
x2

Canopy Lock
FF Ring
x1

* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Nipple (DD) into the Crossbar
(AA) until the Nipple (DD) is
about 0.375” above the
Crossbar (AA).
C. Remove the Canopy Lock Ring
(FF) from the Canopy Chain
BB
Step B
Loop (EE). Place the Ceiling
CC
AA
Canopy (II) over the Canopy
Chain Loop (EE) against the
ceiling to determine the correct
DD
position of the Nipple (DD).
Thread the Canopy Lock Ring
CC
onto the Canopy Chain Loop
Step A
BB
(EE). Adjust the Nipple (DD) to
allow the Ceiling Canopy (II) to
rest against the ceiling when
EE
held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock Ring
II
(FF) and the Ceiling Canopy
(II). Tighten the Hex Nut (CC)
against the Crossbar (AA) to
Figure 2
FF
secure in place.
STEP 3 - Install Column to Fixture
Body

FOR HANGING
STEP 1 - Install Crossbar
A. Attach the Crossbar (A A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) . Tighten until snug .

A. Unfold support arms on fixture
assembly to proper locations.
B. Thread Center Column (B) onto Socket
Assembly (C), tighten until sung.
C. Thread Fixture Loop (A) onto the
nipple on the top of Center Column (B),
hand tighten until sung.

A

B

C

Outlet Box
Green Ground
Screw

Figure 1

2015 QuoizelInc.

AA
Outlet Box Screw
(not included)

Figure 3

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
1of3

January2015

FOR SEMI-FLUSH

STEP 4 - Install Cap and Finial
A. Thread the Nipple (D) into the
Socket Assembly (C).
B. Place the Cap (E) over the
Nipple (D), secure by threading
the Finial (F) onto the Nipple
(D), hand tighten until sung.

STEP 7 - Remove the Mounting
Ball
C

Figure 4

A. Remove the Mounting Ball from
Center Column (B) by unscrew
the Lock Screw.

D

B

Mounting
Ball

B

Figure 7
E

STEP 8 - Install Column to Fixture Body

F

STEP 5 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
the links if needed.
* Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop (A) and
the Canopy Chain Loop (EE), pull the supply wires through the
Fixture Chain (GG) alternating links. After the wires are through the
Fixture Chain (GG), pull the Supply Wires and the Ground Wire
through the Canopy Lock Ring (FF)
and the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain
(GG) to the Fixture Loop (A) with one
Quick Link (HH). Lift the fixture and
Fixture Chain (GG) up And Attach the
DD
other end of the Fixture Chain (GG)
EE
Supply
Wires
onto the Canopy Chain Loop (EE) with
and Ground
another Quick Link (HH). The fixture
HH
Wire
will now hang safely. Close the chain
loop at the Ceiling Canopy Loop (EE).
D. Feed the Supply Wires and Ground
GG
Wire through the Canopy Chain Loop
II
(EE) and Nipple (DD) into the Outlet
Box. Cut the wires leaving
approximately 8” of wire extending
from the Outlet Box.
E. Refer to Step 6 for wire connections.
F. Raise the Ceiling Canopy (II) and
Canopy Lock Ring (FF) up the Fixture
Chain (GG) and over the Canopy
Chain Loop (EE). Tighten the Canopy
Lock Ring (FF) onto the Canopy Chain
Loop (EE) until tight.
G . Process to Step 12 to complete the
installations.
Suggested chain length for Ceiling
height :
8’ ceiling : use 9 links of chain and 2
quick links
9’ ceiling : use 19 links of chain and 2
quick links
10’ ceiling : use 29 links of chain and 2
quick links

Lock
Screw

FF
HH

A

Figure 5

B

A. Unfold support arms on fixture assembly
to proper locations.
B. Thread Center Column (B) onto Socket
Assembly (C), tighten until sung.
C. Thread the Nipple (D) into the Socket
Assembly (C).
D. Place the Cap (E) over the Nipple (D),
secure by threading the Finial (F) onto
the Nipple (D), hand tighten until sung.

C

D
E

Figure 8

F

STEP 9 - Install Crossbar and Mounting Screws
A. Attach the Crossbar (AA) to the Canopy and line up a set of
mounting holes on the Crossbar (AA) to holes on the Canopy.
Thread Mounting Screws (JJ) into the holes. Pass Small Lock
Washers (KK) and thread Small Hex Nuts (LL) onto Mounting
Screws (JJ).
B. Pass the supply wires through the Crossbar (AA). Attach the
Crossbar (AA) to the Outlet Box with the head of the Green Ground
Screw facing you. Secure it with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box
C. Fit the Canopy to Mounting
Supply
Wires
Screws (JJ) and secure with
with Ground Wire
Mounting Balls. Note: The
Green
Canopy should be snug against
JJ
Ground
the ceiling and the Mounting
Screw
Balls. If not, adjust the length of
A
Mounting Screws (JJ) by
unscrewing the assembled
KK
LL
Small Hex Nut (LL) and Small
Outlet Box Screw
Lock Washer (KK) and then
(not included)
screwing the Mounting Screws
(JJ) in or out of the Crossbar
Canopy
(AA) until the correct length is
achieved. Once the Ceiling
Mounting
Canopy with Small Hole (II) is
Ball
secure, remove the Mounting
Ball and Canopy and proceed
Figure 9
to Step 10.
STEP 10 - Wire Connections

STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply

Ribbed side wire
from fixture

2015 QuoizelInc.

White wire
from supply

Smooth side wire
from fixture

Black wire from
supply (or Red)
Ground wire
from supply

A. Cut the wires leaving approximately 6 ” of wire extending from the
fixture canopy. Use standard wire connectors (not included) to make
all wire connections. (Connectors are not included with fixture.)
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.

Figure 6

Black wire from
supply (or Red)

Ground wire
from fixture

Ground wire
from supply

Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of3

Figure 10

January2015

STEP 11 - Install Fixture to Ceiling

CS1718RK
5” Dia.

A. Carefully tuck all wires into the outlet box and position the Canopy
over the outlet box. Align the holes in the Canopy with Mounting
Screws (JJ), then attach the Canopy using Mounting Balls. Hand
tighten until snug.
B. Continue Step 12 to complete the
rest installations.

1”

FINISH: RUSTIC BLACK
69.6”OVERALL HEIGHT
( INCLUDES 48” CHAIN
AND 2 QUICK LINKS )

JJ

Canopy
Mounting
Ball

Figure 11

STEP 12 - Install Bulb

16.5”

A. This fixture uses candelabra
bulb with standard screw base.
Maximum 60 watts.
B. Insert bulb and screw snugly
into place.

Bulb
Socket

Your fixture is now assembled
and ready to use. Enjoy!
18” Dia.
Figure 12
6” Dia.
1.5”

15.8”

18” Dia.

NOTE: TWO LIGHTS SHOWN FOR
ILLUSTRATION PURPOSES ONLY.
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
(4) 60W Candelabra
NO. PART NUMBER REPLACEMENT PART REQ.
Base Bulbs
(Not Supplied)
1

2015 QuoizelInc.

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
3of3

January2015



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jasperz
Create Date                     : 2015:02:02 16:26:28+08:00
Modify Date                     : 2015:02:02 16:26:28+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : IS-CS1718RK.cdr
Creator                         : jasperz
Document ID                     : uuid:de878198-693b-4618-abbe-a3437132b619
Instance ID                     : uuid:eb61ad22-43b9-4e8b-8c9e-d37c7b1de012
Page Count                      : 3

EXIF Metadata provided by EXIF.tools