Is Hc1909

Is-Hy1911 is-hy1911 is-hy1911 images 708 p4dbimg images2.eprevue.net 3:

2017-08-30

: Is-Hc1909 is-hc1909 images 708 p4dbimg

Open the PDF directly: View PDF PDF.
Page Count: 1

DownloadIs-hc1909
Open PDF In BrowserView PDF
ASSEMBLY / INSTALLATION INSTRUCTIONS

6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com

1. Before beginning the installation, carefully unpack and
identify all parts, referring to the illustration.

OUTLET BOX
CROSSBAR

HOUSE SUPPLY and
GROUND WIRES

LOCK WASHER A
LOCK NUT A

OUTLET BOX SCREWS
( not supplied)
NIPPLE

2. Turn power to the installation point OFF at circuit breaker.
3. Slip down the GLASS PANEL to the inside of the CAGE.
Locate the TABS onto the top edge of the GLASS PANEL
and match the holes on them with the mounting holes on the
top edge of the CAGE. Use screw driver, thread the LOCK
SCREWS into the mounting holes and hand tighten until
snug to secure the GLASS PANEL.

LOCK NUT B
CANOPY CHAIN LOOP

4.Install the bulb referring to fixture markings and/or labels for
maximum wattage.

LOCK WASHER B
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN

CEILING CANOPY

CANOPY LOCK RING

FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP

FIXTURE HOOD

LOCK
SCREW

SOCKET

5.Lift the CAGE with GLASS PANELS upward to attach the
bottom of the FIXTURE HOOD and make the holes on the
top edge of the CAGE match the mounting holes on the
bottom of the FIXTURE HOOD. Secure them together with
the LOCK SCREWS. Hand them until snug with screw
driver.
6. Thread the FIXTURE LOOP onto the nipple on the top
center of the FIXTURE HOOD and hand tighten until snug.
7. Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and LOCK WASHER A onto the top
end of NIPPLE. Thread NIPPLE into the center of
CROSSBAR. Locate the LOCK NUT B onto the bottom
end of the NIPPLE. Tighten LOCK NUT A against
CROSSBAR with plier until snug.
8. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing links if
needed. Please note that depending on chain material
thickness, you might be required to use chain pliers to
spread links open. Proceed to attach one end of chain to
FIXTURE LOOP, attached to top of fixture. Pass the fixture
wires through FIXTURE CHAIN alternating links. Proceed
to pass the fixture wires through the following mounting
components in this order: 1)CANOPY LOCK RING;
2)CEILING CANOPY; 3) CANOPY CHAIN LOOP;
4) LOCK WASHER B and LOCK NUT B; 5) NIPPLE;
6) LOCK NUT A and LOCK WASHER A.
9. Making the connections:
(2 people recommended for the remaining steps)
Position the fixture under the ceiling mounted outlet box.
Pass LOCK WASHER B over the NIPPLE. Thread
CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK
NUT B down the NIPPLE, against the CANOPY CHAIN
LOOP and snug with pliers. Pass the wires through the
NIPPLE. Take up wire slack and trim wires so that approx.
6” will remain inside outlet box. Proceed to attach the top
of the FIXTURE CHAIN to the bottom of the CANOPY
CHAIN LOOP.
Using wire connectors (not supplied) connect the HOUSE
GROUND WIRE to the FIXTURE GROUND WIRE;
connect the HOUSE WHITE WIRE to the FIXTURE
SUPPLY WIRE (WHITE or RIBBED SIDE); connect the
HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY
WIRE(BLACK or SMOOTH SIDE). Wrap each
connection with approved electrical tape.

TAB
GLASS PANEL

LOCK SCREW

CAGE

10. With the proper connections made, proceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be
sure that all wires are carefully tucked into the OUTLET
BOX cavity. Secure canopy against ceiling by threading
CANOPY LOCK RING onto the CANOPY LOOP. Tighten
until snug.
11. Restore power to the installation point ON. Retain this
sheet for future reference.

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!

IS-HC1909
2006-2-28
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c17fce9d-f70f-4700-a164-acbf62e95115
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2007:02:28 10:47:35+08:00
Modify Date                     : 2007:02:28 10:47:35+08:00
Document ID                     : uuid:37174f68-d8c6-42cd-8723-26365eeec615
Format                          : application/pdf
Title                           : untitled
EXIF Metadata provided by EXIF.tools

Navigation menu