Is Hc1909

Is-Hy1911 is-hy1911 is-hy1911 images 708 p4dbimg images2.eprevue.net 3:

: Is-Hc1909 is-hc1909 images 708 p4dbimg

Open the PDF directly: View PDF .
Page Count: 1

OUTLET BOX

HOUSE SUPPLY and

GROUND WIRES

OUTLET BOX SCREWS

not supplied()

CROSSBAR

LOCK WASHER A

LOCK NUT A

NIPPLE

LOCK NUT B

LOCK WASHER B

CANOPY CHAIN LOOP

FIXTURE SUPPLY

and GROUND WIRE

FIXTURE CHAIN

CEILING CANOPY

CANOPY LOCK RING

FIXTURE SUPPLY

and GROUND WIRE

FIXTURE LOOP

FIXTURE HOOD

SOCKET

LOCK

SCREW

TAB

GLASS PANEL

LOCK SCREW

CAGE

1 Before beginning the installation carefully unpack and

identify all parts referring to the illustration

2 Turn power to the installation point OFF at circuit breaker

3 Slip down the GLASS PANELto the inside of the CAGE.

Locate the TABS onto the top edge of the GLASS PANEL

and match the holes on them with the mounting holes on the

top edge of the CAGE. Use screw driver, thread the LOCK

SCREWS into the mounting holes and hand tighten until

snug to secure the GLASS PANEL.

4.Install the bulb referring to fixture markings and/or labels for

maximum wattage.

5.Lift the CAGE with GLASS PANELS upward to attach the

bottom of the FIXTURE HOOD and make the holes on the

top edge of the CAGE match the mounting holes on the

bottom of the FIXTURE HOOD. Secure them together with

the LOCK SCREWS. Hand them until snug with screw

driver.

6. Thread the FIXTURE LOOPonto the nipple on the top

center of the FIXTURE HOOD and hand tighten until snug.

7 Fasten the CROSSBAR to the OUTLET BOX with

(2)OUTLET BOX SCREWS(not supplied). Proceed to

thread LOCK NUT A and LOCK WASHER A onto the top

end of NIPPLE. Thread NIPPLE into the center of

CROSSBAR. Locate the LOCK NUT B onto the bottom

end of the NIPPLE. Tighten LOCK NUT A against

CROSSBAR with plier until snug.

8. Locate the FIXTURE CHAIN and determine desired

hanging height of fixture.Adjust chain by removing links if

needed. Please note that depending on chain material

thickness, you might be required to use chain pliers to

spread links open. Proceed to attach one end of chain to

FIXTURE LOOP, attached to top of fixture. Pass the fixture

wires through FIXTURE CHAIN alternating links. Proceed

to pass the fixture wires through the following mounting

components in this order: 1)CANOPY LOCK RING;

2)CEILING CANOPY 3 CANOPY CHAIN LOOP

4 LOCK WASHER B and LOCK NUT B 5 NIPPLE

6 LOCK NUT A and LOCK WASHER A

9.

(2 people recommended for the remaining steps)

Position the fixture under the ceiling mounted outlet box.

Pass LOCK WASHER B over the NIPPLE. Thread

CANOPY CHAIN LOOPonto NIPPLE. Thread LOCK

NUT B down the NIPPLE, against the CANOPYCHAIN

LOOP and snug with pliers. Pass the wires through the

NIPPLE. Take up wire slack and trim wires so that approx.

6” will remain inside outlet box. Proceed to attach the top

of the FIXTURE CHAIN to the bottom of the CANOPY

CHAIN LOOP.

Using wire connectors (not supplied) connect the HOUSE

GROUND WIRE to the FIXTURE GROUND WIRE

connect the HOUSE WHITE WIRE to the FIXTURE

SUPPLY WIRE (WHITE or RIBBED SIDE); connect the

HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY

WIRE(BLACK or SMOOTH SIDE). Wrap each

connection with approved electrical tape.

10. With the proper connections made, proceed to push the

CEILING CANOPY upward over the OUTLETBOX. Be

sure that all wires are carefully tucked into the OUTLET

BOX cavity. Secure canopy against ceiling by threading

CANOPY LOCK RING onto the CANOPY LOOP. Tighten

until snug.

11 Restore power to the installation point ON. Retain this

sheet for future reference.

.

..

.

,

,.

.

;) ;

););

).

;

.

Making the connections:

ASSEMBLY / INSTALLATION INSTRUCTIONS

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

,.

..

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,

CONSULT A LICENSED ELECTRICIAN! IS-HC1909

2006-2-28