Is My1613

2017-08-30

: Is-My1613 is-my1613 images 708 p4dbimg

Open the PDF directly: View PDF PDF.
Page Count: 3

DownloadIs-my1613
Open PDF In BrowserView PDF
INSTRUCTION SHEET IS- MY1613
STYLE NUMBER: MY1613ML

6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com

PACKAGE CONTENTS

ISSUED 04-2008

Part
A

Description

Quantity

Crossbar

1pc
1pc

B

Green Ground Screw

C

Nipple

1pc

D

Hex Nut

3pcs

E

Lock Washer

2pcs

F

Flat Washer

1pc

G

Hex Coupling

1pc

I
J

Ceiling Canopy
Stem
Shade Stop

1pc
1pc
1pc

K

Shade

1pc

L

1pc

M

Shade Holder
Cap

N

Finial

1pc

H

!

H
A

I

B

J

C

K

D
E

L

F

M

G
N

1pc

WARNINGS AND CAUTIONS
WARNING :
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION :
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture.
● We are strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.

PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time : 20 - 30 minutes
● Tools Required for Assembly (not included) : Flathead Screwdriver , Phillips Screwdriver, Pliers, Electrical
Tape, Wire Cutters, Safety Glasses & 3, 60 Watt, Type A - 19 Medium Base Bulbs.
● Helpful Tools (not included) : Wire Strippers.

ASSEMBLY INSTRUCTIONS
STEP 1 :

a . Locate the Crossbar and attach it to the Outlet Box
using the Outlet Box Screws ( not supplied ).
b . Locate the Nipple and thread one Hex Nut onto it about
half way. Slip a Lock Washer onto it and thread one
end of the Nipple into the center hole of the Crossbar .
c . Position the Ceiling Canopy over the outlet box,
passing the mounting hole in the center of the Ceiling
Canopy over the end of Nipple .
d . Adjust the Nipple so approx . 3 / 8 " inch of the Nipple is
protruding from the mounting hole. This adjustment may
take a few tries.
e . When this length is achieved, remove the Ceiling
Canopy and tighten the Hex Nut up against the
underside of the Crossbar with pliers.
1 OF 3

Outlet
Box
Crossbar

Outlet Box
Screw
Hex Nut
Nipple

Lock Washer
Ceiling Canopy

ASSEMBLY INSTRUCTIONS

STYLE NUMBER: MY1613ML

STEP 2

:
Thread another Hex Nut onto the other end of the
nipple. Thread this Hex Nut on just enough so the
inside surface of the pan rests against it.
* You may have to trial fit the Ceiling Canopy one more
times to insure this distance also. This Hex Nut is
needed here to prevent you from crushing down the
center of the Ceiling Canopy .

Nipple
Hex Nut

Ceiling Canopy

STEP 3

:
* Use Wire Connectors ( not supplied ) to connect the
wires .
a . C onnect the House Ground Wire to the Fixture Ground
Wire .
b . C onnect the House White Wire to the Fixture Supply Wire
( White or Ribbed Side ) .
c . C onnect the House Black ( or Red ) Wire to the Fixture
Supply Wire ( Black Side ).
d . Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet
Box .

WHITE OR RIBBED

WHITE OR RIBBED

FROM HOUSE

FROM FIXTURE

BLACK ( OR RED) WIRE

BLACK SIDE

FROM HOUSE

FROM FIXTURE

GROUND WIRE

GROUND WIRE

FROM HOUSE

FROM FIXTURE

STEP 4 :

a . Position the Ceiling Canopy to the ceiling by passing
the Nipple through the center hole .
b . Slip on the Flat Washer and the Lock Washer and then
thread the Hex Coupling to the bottom end of the Nipple .
Snug down assembly until the Ceiling Canopy is flush
against the ceiling .
* Be sure that there are no trapped or pinched wires
along the edge of the pan.

Nipple

Ceiling Canopy

Flat Washer
Lock Washer
Hex Coupling

STEP 5

:
Thread the beaded end of the Stem into the Hex
Coupling and hand tighten until snug .
Ceiling Canopy
Hex Coupling
Stem

STEP 6 :
Install the correct wattage Bulbs referring to the fixture
markings and / or labels for maximum wattage .

2 OF 3

ASSEMBLY INSTRUCTIONS

STYLE NUMBER: MY1613ML

STEP 7 :

Place Shade , Shade Stop and Shade Holder over the
end of the Stem as shown in the illustration . Thread
the Hex Nut onto the end of the Stem to secure the
Shade . Please tighten the Hex Nut gently in case
cracked the Shade .

Ceiling Canopy

Stem

Shade Stop

Shade
Shade Holder
Hex Nut

STEP 8

:
Place the Cap over the end of the Stem and secure
with the Finial . Tighten until snug .

Stem
Cap
Finial

Your installation is completed now . Restore the power
to the installation point ON . Retain this sheet for future
reference .

3 OF 3
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:179a1e42-3c69-4ac3-a904-26439daebeba
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2008:04:25 09:48:08+08:00
Create Date                     : 2008:04:25 09:48:08+08:00
Document ID                     : uuid:18211ea7-fa96-4594-acfa-6288c33657e5
Format                          : application/pdf
Title                           : untitled
EXIF Metadata provided by EXIF.tools

Navigation menu