A K Eye K10 K20 HCR Manual 01.2018
K-EyeK10-K20-HCR_Manual_01.2018
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
ENGLISH K-EYE K10 HCR K-EYE K20 HCR C61430 C61440 INSTRUCTION MANUAL PRELI MINAR Y INDEX Page Contents 2 Safety information 3 Unpacking and preparation 4 Installation and start-up 5 Control panel 9 Maintenance 11 Technical information Congratulations on choosing a Claypaky product! We thank you for your custom. Please note that this product, as all the others in the rich Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements. 1 SAFETY INFORMATION EN IT DE ES FR RU K-EYE K10 & K20 HCR SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: http://www.claypaky.it/en Ref: [FIS016 - Safety Information A.leda K-EYE series] INFORMAZIONI DI SICUREZZA IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: http://www.claypaky.it/en/download Rif: [FIS016 - Safety Information A.leda K-EYE series] INFORMATIONEN ZUR SICHERHEIT WICHTIG: Claypaky empfiehlt, die Sicherheitsinformationen bezüglich dieses Produkts genau zu lesen und aufzubewahren. Sie sind in Digitalversion immer unter folgendem Link auffindbar: http://www.claypaky.it/en/download Ref: [FIS016 - Safety Information A.leda K-EYE series] INFORMACIONES DE SEGURIDAD IMPORTANTE: Claypaky recomienda leer detenidamente y conservar la información de seguridad relativa a este producto. Además, está disponible una versión digital de la misma en el siguiente enlace: http://www.claypaky.it/en/download Ref: [FIS016 - Safety Information A.leda K-EYE series] CONSIGNES DE SÉCURITÉ IMPORTANT: Claypaky recommande de lire attentivement et de conserver les informations de sécurité relatives à ce produit, disponibles en version digitale au lien suivant: http://www.claypaky.it/en/download Réf. : [FIS016 - Safety Information A.leda K-EYE series] ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ ВАЖНО: Claypaky рекомендует внимательно прочитать и сохранить инструкцию по технике безопасности данного изделия, которая всегда доступна в электронном формате по следующей ссылке: http://www.claypaky.it/en/download Наименование: [FIS016 - Safety Information A.leda K-EYE series] 2 UNPACKING AND PREPARATION 1 2 x 183102/805 Packing contents - Fig. 1 2 3 LOCKED UNLOCKED ° ° 90 ° 90 ° 90 90 PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 K-EYE K10 & K20 HCR 3 45° 45° 45° 45° INSTALLATION AND START-UP 4 Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. 5 1 2 2 3 1 Connecting and disconnecting power cable - Fig. 5 K-EYE K10 & K20 HCR 4 CONTROL PANEL 6 Mains Connecting to the mains supply - Fig. 6 7 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 3 PIN SIGNAL 2 SCREEN 1 3 SIGNAL Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3/5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors. 8 Fixture ID 2 Dmx Address Warning Message 1 Switching on the projector - Fig. 8 Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display: Model K-EYE HCR Firmware Version X.X.X Date - Hour xxx (Fixture ID) Dmx Address xxx System errors E: ......................... W: ......................... On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit - Tilt 128 bit). The control panel (Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the key will be cancelled. F K-EYE K10 & K20 HCR 5 9 28 28 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off. Setting the projector Fixture ID On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255). The Fixture ID address can be set with the projector switched off. B C Functions of the buttons - Using the menu F C Confirms the displayed value, or activates the displayed function, or enters the successive menu. Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu. DOWN B Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu. D Return to the top level. E Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù. UP LEFT RIGHT USING THE MENU: 1) Press once – “Main Menu” appears on the display. 2) Use the UP and DOWN keys to select the menu to be used: • Setup (Setup Menu): To set the setting options. • Option (Option Menu): To set the operating options • Informations (Informations Menu): To read the counters, software version and other information. • Manual Control (Manual control Menu): To trigger the test and manual control functions. • Test (Test Menu): To check the proper functionning of effects • Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel. 3) Press to display the first item in the selected menu. 4) Use the UP and DOWN keys to select the MENU items. F F B C B C Setting addresses and options with the projector disconnected The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds. F K-EYE K10 & K20 HCR 6 10 WARNING: no alcohol Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. CAUTION: • To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down before turning the fixture off, so that the front lenses of the fixture are invested as little as possible from the sun. • Set Zoom channel to 255-bit before turning off the projector to facilitate the packaging of the projector. • It is recommended not to use compressed air with more than 4 atmospheres for cleaning the internal parts of the fixture, led board area. This is to avoid damaging electronic components. • To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.). It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations: - General cleaning of internal parts. - Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky. - General visual check of the internal components, cabling, mechanical parts, etc. - Electrical, photometric and functional checks; eventual repairs. Cleaning the lenses Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other detergent could damage the lenses). Continue K-EYE K10 & K20 HCR 7 ➔ 11 1 2 6 3 4 5 Battery removal - Fig. 11 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. K-EYE K10 & K20 HCR 8 MAINTENANCE 3 12 4 1 2 Opening the covers - Fig. 12 13 1 2 1 1 1 Removing/Assembling the lens unit - Fig. 13 Continue K-EYE K10 & K20 HCR 9 ➔ 14 Replacing the line actuator - Fig. 14 ACCESSORIES Two accessories are available for additional control of the beam: TOP HAT Motorized Top Hat, which is applied to the front lens and pulls out automatically together with the zoom. It works as frost/gel holder as well. C21096 Kit Opzionale Top Hat K-EYE K10 HCR FROST/GEL HOLDER You can apply a frost diffuser or a gel by using the optional holder C21097 Kit Opzionale Top Hat K-EYE K20 HCR C21095 Kit telaio per filtro K-EYE K20 HCR K-EYE K10 & K20 HCR C21094 Kit telaio per filtro K-EYE K10 HCR 10 CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES No mains supply. LED exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses broken Dust or grease deposited. CHECKS AND REMEDIES Check the power supply voltage. Call an authorised technician. Replace the cables. Check addresses (see instructions). Call an authorised technician. Call an authorised technician. Clean (see instructions). TECHNICAL INFORMATION POWER SUPPLIES 100/240V 50/60 Hz K-EYE K10 HCR INPUT POWER 450 VA 274 (10.79") Zoom OUT LIGHT SOURCE Light sources: 6-color LED modules LED module: R+G+B+Amber+Cyan+Lime Number of LEDS: 19 LED life expectancy: min. 50,000h Total lumen output: 5,500 lumen Typical lumen manteinance: 70%@50,000 hours Typical CRI value > 97 up to 99 224 (8.82") Zoom IN OPTICS Optics featuring 6-color LED module system + rodbar mixing system + front lens 6°- 50° linear electronic Zoom 496 (19.53") 257 (10.12") 438 (17.24") 391 (15.39") COLOR SYSTEM Color system: R+G+B+Cyan+Amber+Lime LED module Color Temperature control: Linear from 2500K to 8000K (CTO controlled mode plus RAGCB correction) Control of the colors: RAW mode, HSL mode, RGB mode, CMY mode - RAW mode Enable specific control of each color - HSL mode function is based on algorithm. HSL parameters: HUE, HUE fine, Saturation, Crossfade, Path, Tint - RGB mode The projectors works in the same way as a classical RGB fixture - CMY mode The projectors works in the same way as a classical CMY fixture Halo Emulation 750W, 1000W, 1200W, 2000W, 2500W lamp emulation. Gamma Wave: Different chromatic curves for each color Macro: Dedicated color macro channel with 80 preselected colors EFFECTS SECTION Electronic and linear dimmer, 16 bit Strobe 24 flash/sec. Electronic, instant open and blackout. Variable speed pulsation 292 (11.50") K-EYE K10 & K20 HCR 387 (15.24") CONTROL AND PROGRAMMING 27/31 DMX 512 control channels Control signal: USITT DMX 512 Protocols: RDM, WebServer and Art-Net Display: Graphic LCD backlit b/w display Display battery: Long life self-charging buffer battery Pan/Tilt Resolution 16 bit Dimmer Resolution 16 bit Movement control: vectorial DMX signal connection: 3 and 5 pole XLR input and output Firmware update: Software upload through DMX input 11 BODY Structure in aluminium with die-cast plastic cover Handles Two side handles for transportation Device locking PAN and TILT mechanisms for transportation Optional frame for external gels and frost filters Optional top hat (adjustable with the Zoom movement) MOVING BODY PAN range: 540° TILT range: 210° ELECTRONICS Long-life auto-charging buffer battery Preset color and graphic effect macros Function reset controllable from a central control unit Menu-driven internal self-test function Electronic check-up of every single parameter with error alarm DMX level monitoring on each channel Automatic internal data transmission error diagnostics Firmware upgrade with no power Firmware transfer from one light to another SAFETY DEVICES Minimum distance of illuminated objects: 0.2 meters (8”) Minimum distance from flammable materials: 0.2 meters (8”) Max ambient temperature: 40°C (104°F) Max temperature of the external surface: 90°C (194°F) Bipolar circuit breaker with thermal protection Automatic break in power supply in case of overheating Forced ventilation withaxial fans WORKING POSITION Working position: Any Hanging system: 2xfast-lock omega clamps (1/4 turn) on the base Optional 48-51mm, max300Kg clamps; Ø 4mm, lenght680mm safety cable CE MARKING In conformity with the European Directives: • 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD) • 2014/30/EU - Electromagnetic Compatibility (EMC) • 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS) • 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP) WEIGHT 16.5 Kg (36.38 lbs) K-EYE K20 HCR 301 (11,85") Zoom OUT 355 (13.98") 251 (9.89") Zoom IN 488 (19.21") 495 (19.49") 605 (23.82") POWER SUPPLIES 100/240V 50/60 Hz INPUT POWER 750 VA LIGHT SOURCE Light sources: 6-color LED modules LED module: R+G+B+Amber+Cyan+Lime Number of LEDS: 37 LED life expectancy: min. 50,000h Total lumen output: 11,000 lumen Typical lumen manteinance: 70%@50,000 hours Typical CRI value > 97 up to 99 OPTICS Optics featuring 6-color LED module system + rodbar mixing system + front lens 6°- 50° linear electronic Zoom COLOR SYSTEM Color system: R+G+B+Cyan+Amber+Lime LED module Color Temperature control: Linear from 2500K to 8000K (CTO controlled mode plus RAGCB correction) Control of the colors: RAW mode, HSL mode, RGB mode, CMY mode - RAW mode Enable specific control of each color - HSL mode function is based on algorithm. HSL parameters: HUE, HUE fine, Saturation, Crossfade, Path, Tint - RGB mode The projectors works in the same way as a classical RGB fixture - CMY mode The projectors works in the same way as a classical CMY fixture Halo Emulation 750W, 1000W, 1200W, 2000W, 2500W lamp emulation Gamma Wave: Different chromatic curves for each color Macro: Dedicated color macro channel with 80 preselected colors EFFECTS SECTION Electronic and linear dimmer, 16 bit Strobe 24 flash/sec. Electronic, instant open and blackout. Variable speed pulsation CONTROL AND PROGRAMMING 27/31 DMX 512 control channels Control signal: USITT DMX 512 Protocols: RDM, WebServer and Art-Net Display: Graphic LCD backlit b/w display Display battery: Long life self-charging buffer battery Pan/Tilt Resolution 16 bit Dimmer Resolution 16 bit Movement control: vectorial DMX signal connection: 3 and 5 pole XLR input and output Firmware update: Software upload through DMX input BODY Structure in aluminium with die-cast plastic cover Handles Two side handles for transportation Device locking PAN and TILT mechanisms for transportation Optional frame for external gels and frost filters Optional top hat (adjustable with the Zoom movement) MOVING BODY PAN range: 540° Resolution: PAN = 2.11° - PAN FINE = 0.008° TILT range: 210° Resolution: TILT = 0.960° - TILT FINE = 0.004° 423 (16.65") SAFETY DEVICES Minimum distance of illuminated objects: 0.2 meters (8”) Minimum distance from flammable materials: 0.2 meters (8”) Max ambient temperature: 40°C (104°F) Max temperature of the external surface: 90°C (194°F) Bipolar circuit breaker with thermal protection Automatic break in power supply in case of overheating Forced ventilation withaxial fans WORKING POSITION Working position: Any Hanging system: 2xfast-lock omega clamps (1/4 turn) on the base Optional 48-51mm, max300Kg clamps; Ø 4mm, lenght680mm safety cable CE MARKING In conformity with the European Directives: • 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD) • 2014/30/EU - Electromagnetic Compatibility (EMC) • 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS) • 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP) WEIGHT 22.5 Kg (49.6 lbs) ELECTRONICS Long-life auto-charging buffer battery Preset color and graphic effect macros Function reset controllable from a central control unit Menu-driven internal self-test function Electronic check-up of every single parameter with error alarm DMX level monitoring on each channel Automatic internal data transmission error diagnostics Firmware upgrade with no power Firmware transfer from one light to another Clay Paky S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it IST011/001 – EN - PRELIMINARY 01/2018 328 (12.91")
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 12 Creator : QuarkXPress(R) 12.22 Producer : QuarkXPress(R) 12.22 Modify Date : 2018:01:12 08:43:46+01:00 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Title : a Create Date : 2018:01:12 08:43:46+01:00EXIF Metadata provided by EXIF.tools