Panasonic KX T7667 Quick Reference Guide VOICESONIC

KX-T7667 to the manual e87bdc6a-5532-4bef-baba-987f2ab41eca

User Manual: VOICESONIC KX-T7667

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

Panasonic Telephone Systems

Panasonic KX-T7667

www.voicesonic.com
Phone: 877-289-2829

Digital Proprietary Telephone

Quick Reference Guide

Panasonic KX-T7667, Panasonic KXT7667, KX T7667, KX-T7667, KX-T7667B, KX-T7667W, KX-T7667

Important Information
If you are having problems making calls, unplug the extension and connect a known
working telephone. If the known working telephone operates properly, have the
defective telephone repaired by an authorized Panasonic Factory Servicenter. If the
known working telephone does not operate properly, check the KX-TDA series
Business Telephone Systems and the internal extension wiring.
Keep the unit away from heating appliances and devices that generate electrical
noise, such as fluorescent lamps, motors and televisions. These noise sources can
interfere with the performance of the unit.
This unit should not be placed in rooms where the temperature is less than 5 ˚C
(41 ˚F) or greater than 40 ˚C (104 ˚F). Allow 10 cm (3-15/16 in) clearance around the
unit for proper ventilation.
Avoid environments with excessive smoke, dust, mechanical vibration, shock, or
direct sunlight.
Wipe the unit with a soft cloth. Do not clean the unit with abrasive powders or with
chemical agents such as benzine or thinner.
Use only the correct Panasonic handset.
Do not disassemble this unit. Dangerous electrical shock could result. The unit must
only be disassembled and repaired by qualified service technicians.
If damage to this unit exposes any internal parts, immediately disconnect the
telephone line and mains supply. Then return the unit to a servicenter.
Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.
WARNING:
TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. THIS HANDSET EARPIECE IS MAGNETIZED AND MAY RETAIN
SMALL FERROUS OBJECTS.
DISCONNECT THE TELEPHONE LINE CORD FROM THIS PRODUCT IF THIS PRODUCT
EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE.
THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE
HAS STOPPED AND CONTACT AN AUTHORIZED SERVICENTER.

IMPORTANT NOTICE:
Under power failure conditions, this telephone may not operate. Please ensure that a
separate telephone, not dependent on local power, is available for use in an emergency.

Included Accessories: (for extra orders, call toll free 1-800-332-5368)
Handset . . . . . . . . . . . . . . . 1
Telephone Line Cord . . . . . 1

Handset Cord . . . . . . . . . 1
Stand . . . . . . . . . . . . . . . . 1

Please read other important information on pages 11-13 before use.
Document Version: 2006-05

Features List
(CO)

Outside (CO) Line button

(ICD Group)

C. Tone

Off-hook

On-hook

Incoming Call Distribution Group button

Confirmation Tone

R.B. Tone

(DSS)

Feature number

Talk

Direct Station Selection button

Ringback Tone

Operation

Feature

MakingCalls
Calls
Making
To an extension

Calling

To an outside party

extension no.

(CO)

outside
phone no.

Redial
quick dial no.

Quick Dialing
To store

One-touch
Dialing

To dial

desired no.
(max. 32 digits)

(CO)

assigned as a One-touch
Dialing button

Operator Call

0
To store

Personal
Speed Dialing

desired no.
(max. 32 digits)

personal speed
dial no. (2 digits)

C. Tone

To dial
personal speed dial no. (2 digits)

System
Speed Dialing

To dial
system speed dial no. (3 digits)

Doorphone Call

doorphone no. (2 digits)
C. Tone

To set
While hearing a busy tone

Automatic
Callback Busy

To cancel

C. Tone

To answer from an idle extension
While hearing a callback ring

C. Tone

To answer from an idle outside line
While hearing a callback ring
outside phone no.

R.B. Tone

During a Conversation
To hold

Call Hold

To retrieve a call at the holding extension
(CO)

C. Tone

To retrieve an outside call from another extension
(CO)

—2—

(ICD Group)

Features List
Feature

Operation
During a Conversation
extension no.

Call Transfer

C. Tone

To an extension

outside
phone no.

(CO)

To an outside party

Useful Features
To set/cancel

Off-hook Monitor

During a conversation using the handset

SP-PHONE
SP

To set

C. Tone

parking zone no.
(2 digits)

Specified
Auto

C. Tone

Call Park
To retrieve

stored parking
zone no. (2 digits)

C. Tone

To add other parties during a conversation

Multiple Party
Conversation

C. Tone

desired
phone no.

Talk to the
new party.

C. Tone

Talk with
multiple parties.

To leave a conference

C. Tone

(DSS)

Call Pickup

extension no.

Directed

group no. (2 digits)

Group

Sending a Call
Waiting Tone

While hearing a busy tone

Answering a
Call Waiting

To hold the current call then talk to the new party

Wait for an answer.

(CO)

* Disregard this step if both parties are extensions.

—3—

C. Tone

Features List
Feature

Operation
Useful Features
To page

paging group
no. (2 digits)

C. Tone

Announce.

Wait for
an answer. C. Tone

To answer

Paging

C. Tone

To allow/deny a paged announcement

Message
Waiting

Deny

Allow

C. Tone

To leave a message waiting indication
When the called extension is busy or does not answer

Caller

C. Tone

To call back

Called
extension

Log-in/Log-out

1 For Log-in

0 For Log-out

ICD Group Specified
extension no.

All

C. Tone

Before Leaving Your Desk
To set

Setting Absent
Message

parameter
(if required)

To cancel

Call
Forwarding

message no.
(1-9)

All calls

Busy

No answer

Busy/
No answer

Cancel

Both Calls

Outside Calls

Intercom Calls

extension no.
OR

CO line
access no.

—4—

#
outside
phone no.

C. Tone

Features List
Feature

Operation
Before Leaving Your Desk
To lock

Extension
Dial Lock

1
C. Tone

To unlock

extension PIN*
(max. 10 digits)

C. Tone

*PIN: Personal Identification Number

Setting the Telephone According to Your Needs

Do Not Disturb

Extension
Feature Clear

Both Calls

Outside Calls

Intercom Calls

Set

Cancel

C. Tone

0
C. Tone

To set

hour/minute
(4 digits)

AM
OR

Timed
Reminder

once

daily

C. Tone

To cancel

To stop or answer the ring back

0
C. Tone

To set/cancel for intercom calls

No Call

Tone

Whisper OHCA

No tone

Tone

C. Tone

Receiving
Call Waiting
To set/cancel for outside calls

•
•
•

C. Tone

For more details, refer to the Business Telephone System User Manual or consult
your dealer.
You can change the flexible CO buttons to the feature buttons.
“Location of Controls” is shown on pages 7-8.

—5—

Settings on the Programming Mode
To enter the program mode

To exit

Operation
Loop-CO
(L-CO)

(CO)

Single-CO
(S-CO)

(CO)

Direct Station
Selection

(CO)

One-touch
Dialing
Incoming Call
Distribution
Group (ICD
Group)

FWD/DND
- Both calls

(CO)

CO line no.

FWD/DND
- Outside calls

(CO)

extension
no.

FWD/DND
- Intercom calls

(CO)

desired no.

Account

(CO)

Conference

(CO)

ICD Group no.

No line

0
Preferred Line
Assignment-Outgoing

An idle outside line

1
2
3

+ CO button no.

(CO)

Intercom

0
Preferred Line
Assignment-Incoming

1
2

Alternate ReceivingRing/Voice

+ CO button no.

(CO)

Ringing (Tone Call)

Directly (Voice Call)

Ring only
No (No tone)

Call Waiting for
Outside calls

Call Waiting
Selection

0 No Call

1 Tone

Call Waiting Tone
Type Selection

Tone 1

A CO/ICD Group
button

No line
The longest
ringing line
An assigned
outside button

Yes (Tone)

Whisper OHCA

Tone 2

To set an extension PIN

Extension PIN
[Personal Identification
Number]
(PIN-max.10 digits)

Station Programming
Data Default Set

extension PIN

same PIN

To change a stored extension PIN to new one
stored extension PIN

—6—

new PIN

same PIN

Location of Controls
LCD (Liquid Crystal Display) with Backlight
16

15
14
1
2
3
4
5

6
7
8

Headset Jack

Microphone

PROGRAM: Used to enter and exit
the personal programming mode.

CONF (Conference): Used to
establish a multiple party conversation.

INTERCOM: Used to make or receive
intercom calls.

FWD/DND (Call Forwarding/Do Not
Disturb): Used to perform Call
Forwarding or Do Not Disturb.

FLASH/RECALL: Used to disconnect
the current call and make another call
without hanging up.

AUTO ANS (Auto Answer)/MUTE:
Used to receive an incoming call in
hands-free mode or mute the
microphone/handset during a
conversation.
AUTO DIAL/STORE: Used for
System/Personal Speed Dialing or
storing program changes.

REDIAL: Used to redial the last
dialed number.

TRANSFER: Used to transfer a call
to another party.

HOLD: Used to place a call on hold.

—7—

Location of Controls
11

SP-PHONE (Speakerphone): Used
for the hands-free operation.

Navigator Key: Used to adjust the
volume and select desired items for
each function.

MESSAGE: Used to leave a message
waiting indication or call back the
party who left the message waiting
indication.
Message/Ringer Lamp: When you
receive a call, the lamp flashes red.
When someone has left you a
message, the lamp stays on red.

Flexible Outside (CO) Line Button:
Used to make or receive an outside
call. Pressing this button seizes an
idle outside line automatically. (Button
assignment is required.) Also used as
feature buttons. (Button assignment is
required.)

PAUSE: Used to insert a pause
during dialing.

Setting
Speaker/Ringer/Handset/Headset Volume
Speaker Volume

While in hands-free conversation

Ringer Volume

While on-hook or receiving a call

Handset/Headset Volume

While using the handset or headset

LCD Contrast/Headset Mode
While on-hook
LCD Contrast

Headset Mode

Press UP or DOWN.

Ring Tone
(CO)

Press Twice.

*1 The ring tone pattern of patterns 09 to 30 is the same as pattern 01.

LCD Backlight
While on-hook
0

Automatic *2

Always On

Always Off

*2 Default setting: Automatic

—8—

Press UP or DOWN.

Tilt Angle
The tilt angle of the unit can be adjusted.
To adjust the angle, insert the stand into the desired holes as shown below.

< LOW >

PUSH
PUSH

LOW

HIGH

< HIGH >

PUSH
PUSH

LOW

HIGH

—9—

Connection
The telephone line cord
(included)

To the main unit ( TO MAIN UNIT )
/PABX

< Back view >

Headset

Headset (not included)
Recommendable: KX-TCA86, KX-TCA91,
KX-TCA92
Not compatible: KX-T7090

CAUTION
Ensure the cord is inserted in the groove
to prevent damage to the connector.

Wall Mounting
1 Pull down the handset hook until it locks,

3 Mount the unit on the wall.

so the tab holds the handset.

83 mm
(3-1/4 in)

2 Remove the attached stand.
2

To temporarily place the handset down
during a conversation, hook it over the
top edge of the phone as shown.

— 10 —

Important Safety Instructions
When using this unit, basic safety
precautions, including those below, should
always be followed to reduce the risk of
fire, electric shock and injury to persons.
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on this unit.
3. Unplug this unit from the main unit
before cleaning. Do not use liquid or
aerosol cleaners. Clean with a damp
cloth.
4. Do not use the unit near water, for
example, near a bathtub, kitchen sink,
or laundry tub, in a wet basement, or
near a swimming pool.
5. Place this unit on a flat surface.
Serious damage and/or injury may
result if the unit falls.
6. The unit should never be placed near
or over a radiator or other heat source.
7. Do not allow anything to rest on the
extension cord. Do not locate this unit
where the cord may be stepped on or
tripped on.
8. To reduce the risk of fire or electric
shock, do not overload wall outlets and
extension cords.
9. Do not insert objects of any kind into
this unit through openings, as they
may touch dangerous voltage points or
short out parts that could result in a
risk of fire or electric shock. Never spill
liquid of any kind on the unit.
10. To reduce the risk of electric shock, do
not disassemble this unit. Only
qualified personnel should service this
unit. Opening or removing covers may
expose you to dangerous voltages or
other risks. Incorrect reassembly can
cause electric shock.

11. Unplug this unit from the main unit
and have the unit serviced by
qualified service personnel in the
following cases:
A. When the extension cord is
damaged or frayed.
B. If liquid has been spilled on the
unit.
C. If the unit has been exposed to rain
or water.
D. If the unit does not work normally
by following the manual. Adjust
only controls covered by the
manual. Improper adjustment may
require repair by an authorized
servicenter.
E. If the unit has been dropped, or
damaged.
F. If the unit's performance
deteriorates.
12. Avoid using a telephone (other than
a cordless type) during an electrical
storm. There is a remote risk of
electric shock from lightning.
13. Do not use the telephone in the
vicinity of a gas leak to report the
leak.

— 11 —

SAVE THESE
INSTRUCTIONS

FCC Information
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued compliance with FCC rules, do not make any unauthorized
changes or modifications to this equipment would void the user's authority to
operate this device.
When programming emergency numbers and/or making test calls to emergency
numbers:
1) Remain on the line and briefly explain to the dispatcher the reason for the call
before hanging up.
2) Perform such activities in the off peak hours, such as early morning hours or
late evenings.

— 12 —

Customer Information
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of the cabinet of this equipment is a label
that contains, among other information, a product identifier in the format
US: AAAEQ##Txxxx. If requested, this number must be provided to the telephone
company.
If trouble is experienced with this equipment KX-T7667, for repair or warranty
information, please contact:
Panasonic Services Company
BTS Center
1225 Northbrook Parkway Suite
1-216 Suwanee
GA 30024
If the equipment is causing harm to the telephone network, the telephone
company may request that you disconnect the equipment until the problem is
resolved.
Hearing Aid Compatibility:
This telephone provides magnetic coupling for hearing aids.
Use only handsets or other acoustic devices with this equipment that are
compliant with the hearing aid compatibility requirements of FCC Part 68.

Other Important Information
When you ship the product:
Carefully pack and send it prepaid, adequately insured and preferably in the
original carton. Attach a postage-paid letter, detailing the symptom to the outside
of the carton.
DO NOT send the product to the Executive or Regional Sales offices. They are
NOT equipped to make repairs.
Product service:
Panasonic Servicenters for this product are listed in the servicenter directory.
Consult your certified Panasonic dealer for detailed instructions.

— 13 —

Note

— 14 —

Note

— 15 —

For your future reference
SERIAL NO.
(found on the bottom of the unit)

DATE OF PURCHASE

NAME OF DEALER
DEALER'S ADDRESS
DEALER'S TEL. NO.

Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is prohibited
without the written consent of Panasonic Communications Co., Ltd.
2006 Panasonic Communications Co., Ltd. All Rights Reserved.

See More
Panasonic Manuals

3DQDVRQLF7HOHSKRQH6\VWHPV

www.voicesonic.com
Phone: 877-289-2829

PSQX4167ZA-BM KK0506SY0(M)

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Keywords                        : Panasonic KX-T7667, Panasonic KXT7667, KX T7667, KX-T7667, KX-T7667B, KX-T7667W, KX-T7667 Quick Reference, Reference Guide, Panasonic Quick Reference Guide
Create Date                     : 2003:06:04 15:41:31Z
Modify Date                     : 2010:04:01 11:08:37-04:00
Metadata Date                   : 2010:04:01 11:08:37-04:00
Creator Tool                    : FrameMaker 7.0
Format                          : application/pdf
Creator                         : 
Title                           : Panasonic KX-T7667 Quick Reference Guide
Description                     : Panasonic KX-T7667 Quick Reference Guide
Subject                         : Panasonic KX-T7667, Panasonic KXT7667, KX T7667, KX-T7667, KX-T7667B, KX-T7667W, KX-T7667 Quick Reference, Reference Guide, Panasonic Quick Reference Guide
Document ID                     : uuid:43bab73d-c21f-4aac-a3f9-48276c16ff61
Instance ID                     : uuid:b9272170-d6b5-48e3-b820-8d62e71f7063
Page Count                      : 16

EXIF Metadata provided by EXIF.tools

Panasonic KX T7667 Quick Reference Guide VOICESONIC

KX-T7667 to the manual e87bdc6a-5532-4bef-baba-987f2ab41eca

Navigation menu

Versions of this User Manual:

Views

Navigation