TWR KE18F User's Guide MKE1x F TWRKE18F User
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
NXP Semiconductors User's Guide Document Number: TWRKE18FUG Rev. 0, 09/2016 TWR-KE18F User's Guide 1. Introduction The NXP Tower development platform is a set of software and hardware tools for evaluation and development. It is an ideal tool for the rapid prototyping of microcontroller-based applications. The TWR-KE18F supports a power supply voltage range from 3.3 V to 5 V. It features a MKE18F16, a device featuring a maximum operating frequency of 168 MHz, up to 512 KB Flash size, and numerous analog and digital peripherals. The TWR-KE18F includes the ARM® open standard embedded serial and debug adapter known as OpenSDA(CMSIS-DAP). This circuit offers the user several options for serial communications, flash programming, and run-control debugging. The TWR-KE18F microcontroller module is designed to work either in standalone mode or as part of the NXP Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. There are many software development tool options available to the user. Choices include Kinetis Design Studio (KDS), IAR Embedded Workbench, and Keil MDK featuring the µVision IDE. All of these features combine to give users the Tower needed to rapidly prototype many embedded designs: a powerful microcontroller built on a very low-power core and SOC platform, easy-access to I/O with a large © 2016 NXP B.V. Contents 1. 2. 3. 4. Introduction .................................................................... 1 Getting Started ................................................................ 2 TWR-KE18F Features ..................................................... 2 TWR-KE18F Hardware Description ................................ 4 4.1. Power supply ........................................................ 4 4.2. OpenSDA circuit (CMSIS-DAP) ........................... 5 4.3. Microcontroller ..................................................... 7 4.4. Sensor .................................................................. 9 4.5. Infrared port ....................................................... 10 4.6. CAN transceiver ................................................. 11 4.7. Potentiometer, thermistor, pushbuttons, and LEDs 12 4.8. FlexIO header ..................................................... 12 5. Default Jumper Setting .................................................. 13 6. References .................................................................... 14 7. Revision History ........................................................... 15 TWR-KE18F Features ecosystem of compatible hardware, a flexible programming and debug interface, and a large ecosystem of software development environments. 2. Getting Started Refer to the TWR-KE18F Quick Start Package for step-by-step instructions for getting started with the Tower board. See the “Jump Start Your Design” section at nxp.com/TWR-KE18F for the Quick Start Package and software lab guides. 3. TWR-KE18F Features The TWR-KE18F hardware is a NXP Tower development board assembled with the following features: • MKE18F512VLL16 MCU (168 MHz core clock, 512 KB flash, 64 KB RAM, 100LQFP package) • Tower-compatible processor board • Onboard OpenSDA (CMSIS-DAP) circuit: K20DX128VFM5 with debug and virtual serial port • Four user-controlled status LEDs and one RGB LED • Two mechanical push buttons and one reset button • I/O headers for easy access to MCU I/O pins • Thermistors and potentiometer • FXOS8700CQ 3D accelerometer + 3D magnetometer • Board power select with 3.3 V or 5 V MCU operation • Infrared port communication • CAN transceiver • Flex™ I/O header The TWR-KE18F features two MCUs: The target MCU is the MKE18F512VLL16. The OpenSDA(CMSIS-DAP) MCU is the MK20DX128VFM5. Figure 1 shows the block diagram of the TWR-KE18F board. The primary components and their location on the hardware assembly are shown in Figure 2 and Figure 3. TWR-KE18F User's Guide, Rev. 0, 09/2016 2 NXP Semiconductors TWR-KE18F Features Figure 1. TWR-KE18F block diagram Figure 2. Front Side of TWR-KE18F TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 3 TWR-KE18F Hardware Description Figure 3. Back Side of TWR-KE18F 4. TWR-KE18F Hardware Description 4.1. Power supply When TWR-KE18F is installed into the Tower System, the board power supply can be either from an on-board source (CMSIS-DAP USB connector) or from another source through Tower Elevator. By default, in stand-alone operation, the TWR-KE18F board power source is 5.0 V, which is derived from the CMSIS-DAP USB microB connector J2. One low-dropout regulator U6 provides 3.3 V supply from the 5.0 V input voltage. All of the user-selectable power options for peripherals can be configured by headers. Refer to the default headers setting table section 5. The following figure shows the schematic drawing for the power supply inputs and the on-board voltage regulator. TWR-KE18F User's Guide, Rev. 0, 09/2016 4 NXP Semiconductors TWR-KE18F Hardware Description Figure 4. Power supply The following table lists some power sources descriptions. Table 1. TWR-KE18F power sources Power Source Name P5V_TRG_SDA P5V_ELEV P3V3_REG V_BRD VREG_IN MCU_PWR MCU_VDD VDDA VREFH Description Output of USB power switch controlled by the VTRG_EN signal from the OpenSDA and the ELE_PS_SENSE signal from the TWR elevator connectors. Goes to regulator input select header. Power to the elevator boards. Output of 3.3 V regulator or from the Elevator connectors. May also be supplied externally by connecting to the board voltage select header. Output of 3.3 V or 5 V regulators as selected by the board voltage select header. May also be supplied externally by connecting to the board voltage select header. Power into the on board voltage regulators. MCU digital power. Filtered from V_BRD. MCU digital power input after current measurement jumper. VDDA power for MCU and analog circuits. Filtered from MCU_PWR. Upper reference voltage for ADC on the MCU. Filtered from VDDA. 4.2. OpenSDA circuit (CMSIS-DAP) The OpenSDA circuit (CMSIS–DAP) is an open-standard serial and debug adapter. It bridges serial and debug communications between a USB host and an embedded target processor as shown in Figure 5. CMSIS-DAP features a mass storage device (MSD) bootloader, which provides a quick and easy mechanism for loading different CMSIS-DAP Applications such as flash programmers, run-control debug interfaces, serial-to-USB converters, and more. Two or more CMSIS-DAP applications can run simultaneously. For example, run-control debug application and serial-to-USB converter runs in parallel to provide a virtual COM communication interface while allowing code debugging via CMSIS-DAP TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 5 TWR-KE18F Hardware Description with just single USB connection. These two applications are provided in a single code package. Refer to the CMSIS-DAP User’s Guide for more details. Figure 5. CMSIS-DAP block diagram CMSIS-DAP is managed by a Kinetis K20 MCU built on the ARM Cortex-M4 core. The CMSIS-DAP circuit includes a status LED (D1) and a RESET pushbutton (SW1). The pushbutton asserts the Reset signal to the KE18F target MCU. It can also be used to place the CMSIS-DAP circuit into bootloader mode by holding down the RESET pushbutton while plugging the USB cable to USB connector J2. Once the CMSIS-DAP enters bootloader mode, other CMSIS-DAP applications such as debug app can be programmed. SPI and GPIO signals provide an interface to the SWD debug port of the KE18F. Additionally, signal connections are available to implement a UART serial channel. The CMSIS-DAP circuit receives power when the USB connector is plugged into a USB host. 4.2.1. Debug interface Signals with SPI and GPIO capability are used to connect directly to the SWD of the KE18F. These signals are also brought out to a standard 10-pin Cortex Debug connector (J10) as shown in Figure 6. The user could use J10 to debug and download code to KE18F with this SWD/JTAG interface. TWR-KE18F User's Guide, Rev. 0, 09/2016 6 NXP Semiconductors TWR-KE18F Hardware Description Figure 6. SWD/JTAG debug connector 4.2.2. Virtual serial port A serial port connection is available between the CMSIS-DAP MCU and pins PTB1 and PTB0 of the KE18F. Several of the default CMSIS-DAP applications provided by NXP, including the MSD Flash Programmer and the CMSIS-DAP USB HID interface, provide a USB communications device class (CDC) interface that bridges serial communications between the USB host and this serial interface. 4.3. Microcontroller MKE18F16 MCU is the high end series MCU in Kinetis E family, providing robust 5 V solution with the high performance ARM® Cortex®-M4 core clock running up to 168 MHz, flash size up to 512 KB. It offers multiple ADCs and Flextimers, a CAN 2.0B compliant FlexCAN module and rich suite of communication interfaces including UARTs, I2Cs, SPIs, and FlexIO which provide flexibility for serial communication emulation. The following table lists the features of MKE18F512VLL16. Table 2. Features of MKE18F512VLL16 Feature ARM Cortex-M4 core System Description 32-bit MCU core from ARM's Cortex-M class adding DSP instructions and single-precision floating point unit based on ARMv7 architecture System integration module Power management and mode controllers o Multiple power modes available based on high speed run, run, wait, stop, and power-down modes Miscellaneous control module Crossbar switch TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 7 TWR-KE18F Hardware Description Table 2. Features of MKE18F512VLL16 Feature Memories Clocks Security Analog Timers Communications Description Memory protection unit Peripheral bridge Direct memory access (DMA) controller with multiplexer to increase available DMA requests. DMA can now handle transfers in VLPS mode External watchdog monitor (EWM) Watchdog (WDOG) Program flash memory FlexMemory o FlexNVM o FlexRAM SRAM Boot ROM Multiple clock generation options available from internally and externally generated clocks System oscillator to provide clock source for the MCU Cyclic Redundancy Check (CRC) module for error detection Software watchdog (WDOG) with independent clock source External watchdog monitor (EWM) module Error-correcting code (ECC) on Flash memories 128-bit unique identification (ID) number Memory Protection Unit (MPU) module ADC self-test and calibration feature High speed analog-to-digital converter (ADC) Comparator (CMP) Digital-to-analog converter (DAC) Bandgap voltage reference (1V reference voltage) Programmable delay block (PDB) FlexTimers Low-power periodic interrupt timer (LPIT) Low power timer (LPTMR) Independent real time clock (RTC) FlexCAN Low-power Serial peripheral interface (LPSPI) Low-power Inter-integrated circuit (LPI2C) Low-power UART (LPUART) FlexIO 4.3.1. Clock source The KE18F MCU starts up to the default reset clock for core/system clock, which is 48 MHz from FIRC. Software can enable the main external oscillator (EXTAL/XTAL), or slow frequency internal reference (SIRC) 2/8 MHz if desired as the core/system clock. There is one System PLL inside KE18F clock module, it enables the chip to run up to the maximum frequency of 168 Mhz. The external oscillator/resonator can range from 32.768 KHz to 32 MHz. Its main usage is for RTC time base. An 8 MHz crystal is the default external source for the SCG oscillator inputs (XTAL/EXTAL). The clock source diagram is shown in the following figure. TWR-KE18F User's Guide, Rev. 0, 09/2016 8 NXP Semiconductors TWR-KE18F Hardware Description Figure 7. Clock source 4.3.2. Serial port The primary serial port interface signals are PTB1 and PTB0. These signals are connected to both the CMSIS-DAP and to the J3/J5 TWR elevator connector. 4.3.3. Reset The PTA5/RESET signal on KE18F is connected externally to a pushbutton, SW1, and also to the CMSIS-DAP circuit. The reset button can be used to force an external reset event in the target MCU. The reset button can also be used to force the CMSIS-DAP circuit into bootloader mode. 4.4. Sensor FXOS8700CQ is a small, low-power, 3-axis, linear accelerometer + magnetometer. The device features a selectable I2C or point-to-point SPI serial interface with 8-bit accelerometer and 14-bit magnetometer ADC resolution along with smart-embedded functions. It is interfaced through an I2C bus and three GPIO signals as shown in the following figure. TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 9 TWR-KE18F Hardware Description Figure 8. FXOS8700CQ sensor 4.5. Infrared port An infrared transmit and receive interface is implemented on the board. The PTC7 pin directly drives an infrared diode. The receiver uses an infrared phototransistor connected to an on-chip analog comparator ACMP2_IN3 through a low-pass filter. Then the output of the analog comparator ACMP2_OUT is routed to a UART module externally for easier processing of the incoming data stream. The Infrared port schematic is shown in the following figure. TWR-KE18F User's Guide, Rev. 0, 09/2016 10 NXP Semiconductors TWR-KE18F Hardware Description Figure 9. Infrared port 4.6. CAN transceiver The TWR-KE18F features a Controller Area Network interface using a NXP MC33901WEF CAN transceiver. The signals from the transceiver are connected to two 3-pin headers with the FlexCAN module pin out of KE18F. They can also be routed to the CAN transceiver TJA1051T/3 on TWR SER board through the elevator. The CAN transceiver schematic is shown in the following figure. TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 11 TWR-KE18F Hardware Description Figure 10. CAN receiver 4.7. Potentiometer, thermistor, pushbuttons, and LEDs The TWR-KE18F features: • • • • • 4.8. A potentiometer connected to an ADC input channel (PTC14/ADC0_SE12) A thermistor connected to two ADC input channels (PTA0/ADC0_SE0 and PTA1/ADC0_SE1) Two pushbutton switches (SW2 and SW3 connected to PTD3 and PTD6) User controllable LEDs connected to GPIO signals — Yellow LED D8 connected to PTC12 — Red LED D6 connected to PTC10 — Orange LED D9 connected to PTC13 — GREEN LED D7 connected to PTC11 A RGB LEDs connected to FTM signals — RED color connected to PTD16/FTM0_CH1 — GREEN color connected to PTD15/FTM0_CH0 — BLUE color connected to PTB5/FTM0_CH5 FlexIO header KE18F has one on-chip FlexIO module, which is capable of supporting a wide range of protocols including: UART, I2C, SPI, I2S, and PWM generation. It is more efficient than integrating multiple peripherals for each desired protocol. There are eight FlexIO pins implemented in total and bonded out on J20, as shown in the following figure. TWR-KE18F User's Guide, Rev. 0, 09/2016 12 NXP Semiconductors Default Jumper Setting Figure 11. FlexIO header 5. Default Jumper Setting There are several jumpers provided for isolation, configuration, and feature selection. The following table provides details. Table 3. Default jumper settings Jumper Option Setting Description J3 UART TX Selection 1-2 Connect to Elevator UART TX 2-3 Connect to OpenSDA UART TX 1-2 Connect OpenSDA reset to MCU 2-3 Connect pin reset to MCU directly, when OpenSDA is not powered UART RX Selection 1-2 Connect to Elevator UART RX 2-3 Connect to OpenSDA UART RX J6 CAN TX Selection 1-2 Connect CAN transceiver to MCU CAN0 TX pin directly 2-3 Connect CAN transceiver to Elevator CAN TX J7 CAN RX Selection 1-2 Connect CAN transceiver to MCU CAN0 RX pin directly 2-3 Connect CAN transceiver to Elevator CAN RX J8 CAN Transceiver connection ON Connection with external board OFF No connection with external board J9 POTENTIOMETER Enable ON Enable potentiometer OFF Disable potentiometer J11 OpenSDA SWD CLK connection ON Connect SWD_CLK to OpenSDA circuit OFF Disconnect SWD_CLK to OpenSDA circuit OpenSDA SWD DIO connection ON Connect SWD_DIO to OpenSDA circuit J12 OFF Disconnect SWD_DIO to OpenSDA circuit J4 Reset Selection J5 TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 13 References Table 3. Default jumper settings Jumper J13 J16 J17 J18 J19 Option Reset connection Board power supply selection Upper reference voltage VREFH selection Analog circuits power VDDA connection MCU digital power connection J21 Elevator 3.3V connection J22 Elevator 5V connection J23 Elevator 5V connection J24 External clock selection Setting Description ON Connect reset signal to MCU pin OFF Disconnect reset signal to MCU pin 1-2 Board voltage V_BRD power from OpenSDA USB, 5V 2-3 Board voltage V_BRD power from regulator,3.3V 1-2 VREFH from 3.3V regulator 2-3 VREFH from VDDA ON Connect VDDA to board power V_BRD OFF Disconnect VDDA to board power V_BRD ON Connect MCU_VDD to board power V_BRD OFF Disconnect MCU_VDD to board power V_BRD ON Connect 3.3V regulator output to TWR elevator OFF Disconnect 3.3V regulator output to TWR elevator ON Connect 5V USB power switch output to TWR elevator OFF Disconnect 5V USB power switch output to TWR elevator ON Connect 5V OpenSDA input to TWR elevator OFF Disconnect 5V OpenSDA input to TWR elevator 1-2 External 8Mhz crystal input 2-3 External oscillator input to EXTAL pin directly 6. References The reference documents for the TWR-KE18F hardware are shown below. All of these documents are available online at www.nxp.com/TWR-KE18F. • TWR-KE18F Quick Start Guide: Quick Start Guide and supporting files for getting started with the TWR-KE18F. • TWR-KE18F User’s Guide: Document overview and detailed information for the TWR- KE18F hardware. • TWR-KE18F Schematics PDF: Schematics for the TWR- KE18F hardware. • KE18F Sub-Family Reference Manual: A reference manual for KE18F sub-family devices TWR-KE18F User's Guide, Rev. 0, 09/2016 14 NXP Semiconductors Revision History 7. Revision History Table 4. Revision history Revision number Date Substantive changes 0 09/2016 Initial release TWR-KE18F User's Guide, Rev. 0, 09/2016 NXP Semiconductors 15 How to Reach Us: Information in this document is provided solely to enable system and software Home Page: nxp.com implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. NXP reserves the right to make changes without further Web Support: nxp.com/support notice to any products herein. NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the following address: nxp.com/SalesTermsandConditions. NXP, the NXP logo, NXP SECURE CONNECTIONS FOR A SMARTER WORLD, Freescale, the Freescale logo, and Kinetis are trademarks of NXP B.V. All other product or service names are the property of their respective owners. ARM, the ARM Powered logo, and Cortex are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved. © 2016 NXP B.V. Document Number: TWRKE18FUG Rev. 0 09/2016
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : NXP Semiconductors Description : TWR-KE18F User's Guide Title : TWR-KE18F User's Guide Subject : 5V MCU, 32-bit MCU, Kinetis E, KE1xF, CAN, Dual CAN, FlexIO, BootROM, EERPOM, FlexNVM, ECC, MPU, cache, TWR-KE18F, HVP-KE18F Create Date : 2016:09:20 09:38:05+02:00 Creator Tool : Microsoft® Word 2016 Modify Date : 2016:09:20 09:38:48+02:00 Metadata Date : 2016:09:20 09:38:48+02:00 Producer : Microsoft® Word 2016 Document ID : uuid:018a75be-7d5f-4451-a8ab-dc66b294c329 Instance ID : uuid:31679e3d-c376-4c55-80ca-986bfb74bbb7 Page Mode : UseOutlines Page Count : 16 Author : NXP Semiconductors Keywords : 5V MCU, 32-bit MCU, Kinetis E, KE1xF, CAN, Dual CAN, FlexIO, BootROM, EERPOM, FlexNVM, ECC, MPU, cache, TWR-KE18F, HVP-KE18F Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools