Manual 8.578.80.02 HK MP5 22 Rimfire 07R11
User Manual: Manual-HK-MP5-22-Rimfire-07R11
Open the PDF directly: View PDF 
.
Page Count: 30
| Download | |
| Open PDF In Browser | View PDF |
MP5 Self loading rifle Cal. .22L.R. HV USA Rear Sight Ejection Port Handguard Front Sight Compensator Buttstock Latch Magazine Buttstock Trigger Guard Magazine Release Buttpad Upper Receiver Charging Handle Rear Receiver Pin Muzzle Lower Receiver Compensator WARNING: READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. MADE BY CARL WALTHER Grip Trigger Safety No. Contents Page Identification 1 Safety Rules 3 - 11 1 Safety Operating Instructions 12 2 Inspection 13 3 Loading the Firearm 14 4 Insertion of the First Cartridge 5 Firing 6 Decocking the Hammer 7 Firearm with Empty Magazine 16 8 Unloading 16 9 Clearing Misfires 17 10 Settings - Sights, Stock, Bolt Speed, Optical Sight 11 Field Stripping the Firearm 12 Cleaning 15 15-16 18 - 19 20 21 -22 13 Storage 22 14 Repair 23 15 Warranty CONTENTS 16 Technical Data 23 - 24 25 17 Exploded View / Parts 26 - 27 18 Variants / Accessories 28 - 29 19 Contact 2 14 - 15 back YOUR SAFETY RESPONSIBILITY SAFETY IS YOUR NUMBER ONE RESPONSIBILITY! AT HOME, IN THE FIELD, AT THE RANGE, OR ANYWHERE, THE FIRST CONCERN OF EVERY FIREARM OWNER SHOULD BE SAFETY. APPLY THE FOLLOWING SAFETY RULES IN EVERY SITUATION, WITH ANY KIND OF FIREARM. WARNING: YOU MUST FOLLOW ALL OF THESE SAFETY RULES TO ENSURE THE SAFE USE OF YOUR FIREARM YOUR SAFETY RESPONSIBILITIY WARNING: SAFE GUN HANDLING IS YOUR PERSONAL RESPONSIBILITY! WARNING: SAFE USE OF A FIREARM IS YOUR PERSONAL RESPONSIBILITY AND THE FAILURE TO FOLLOW ALL OF THESE BASIC SAFETY RULES MAY RESULT IN SEVERE PERSONAL INJURY OR DEATH TO YOU OR OTHERS. YOU ARE THE MOST IMPORTANT SAFETY DEVICE WHEN IT COMES TO THE USE OF YOUR FIREARM. CARL WALTHER GMBH AND UMAREX USA WILL NOT BE RESPONSIBLE FOR ANY PERSONAL INJURY, DEATH OR PROPERTY DAMAGE THAT RESULTS FROM: (1) (2) (3) (4) (5) THE CRIMINAL OR NEGLIGENT USE OF THIS FIREARM; A DISREGARD OF THESE SAFETY INSTRUCTIONS AND WARNINGS; IMPROPER OR CARELESS HANDLING OF THIS FIREARM; THE USE OF NON-STANDARD, DEFECTIVE, IMPROPER OR RELOADED AMMUNITION; OR IMPROPER OR NEGLIGENT MODIFICATIONS OR REPAIR TO THE FIREARM. 3 - SAFE GUN HANDLING IS YOUR PERSONAL RESPONSIBILITY AT ALL TIMES. Firearms are dangerous and can cause serious injury or death if they are misused or used inappropriately. Safety must be the first consideration of anyone who owns or handles firearms. - YOU ARE RESPONSIBLE FOR FIREARM SAFETY AT ALL TIMES. You must undertake full-time responsibility for your firearm´s safety and security. You must protect yourself and all others against injury or death from misuse of the firearm. - SAFE FIREARM STORAGE IS YOUR RESPONSIBILITY. You must secure firearms safely from children and unauthorized users. A lock has been provided for use with this firearm. Never assume that the use of this lock is sufficient to safely secure your firearm. You must always evaluate your personal situation and employ the security system(s) that meet your needs and prevent children and unauthorized users from gaining access to your firearm. - Accidents are the result of violating the rules of safe gun handling and common sense. YOUR SAFETY RESPONSIBILITIY - For your safety and the safety of others, NEVER RELY ON MECHANICAL FEATURES ALONE. Only your safe gun handling habits will ensure the safe use of the firearm. This is your responsibility. - NEVER KEEP AMMUNITION IN THE SAME LOCATION AS THE FIREARM. Store in a separate and secure place. - DO NOT ALTER, MODIFY OR REPLACE ANY OF THE PARTS OF THE INTERNAL COMPONENTS OF YOUR FIREARM All work must be performed by an Umarex USA authorized gunsmith. If you do otherwise, improper functioning may occur and serious injury may result. - NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THE INTERNAL COMPONENTS OF YOUR FIREARM including the firing pin, or sear. Improper manipulation of any internal component may affect the safety and reliability of your firearm and may cause serious injury. 4 WARNING: - READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE USING YOUR FIREARM THE FAILURE TO FOLLOW THESE BASIC FIREARM SAFETY RULES MAY RESULT IN AN UNINTENDED WHICH COULD CAUSE SERIOUS PERSONAL INJURY OR DEATH TO YOU AND OTHERS. DISCHARGE - BEFORE HANDLING ANY FIREARM, UNDERSTAND ITS OPERATION. Not all firearms are the same. Familiarize yourself with the mechanical features of any firearm you intend to use. If you feel uncertain about any operational aspects of your firearm, please contact Umarex USA before proceeding with its operation. - ALWAYS SAFELY STORE AND SECURE YOUR FIREARM. Safe and secure storage of your firearm is one of the most important responsibilities of firearm ownership. It is a full-time responsibility. You must always secure your firearm and ammunition separately so that they are not accessible to children or other unauthorized persons. (See Safe Storage Instructions in this manual). YOUR SAFETY RESPONSIBILITY - ALWAYS KEEP YOUR FIREARM POINTED IN A SAFE DIRECTION. NEVER point this firearm at any person. Never point at anything you do not intend to shoot whether or not the firearm is loaded. This is particulary important when loading, unloading, or field stripping the gun. ALWAYS control the direction of the muzzle. - NEVER PLACE YOUR FINGER ON THE TRIGGER OR INSIDE THE TRIGGER GUARD UNLESS YOU INTEND TO FIRE. Ensure that other objects do not touch the trigger. - ALWAYS BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT. Always be sure of where the bullet will strike and shoot only where there is a safe backstop free of obstructions, water or other surfaces which can cause ricochets. Think of what the bullet may hit if it misses the target or ricochets. Do not fire into the sky. - NEVER DISASSEMBLE YOUR FIREARM OR MANIPULATE THE INTERNAL COMPONENTS OF YOUR FIREARM beyond the field stripping procedure outlined in this manual. Improper disassembly or manipulation of your firearm may be dangerous and can lead to serious injury or death. - NEVER CARRY OR STORE A FIREARM with the hammer or striker in the cocked position. 5 - NEVER ALLOW YOUR FIREARM TO BE USED BY INDIVIDUALS WHO HAVE NOT READ OR DO NOT UNDERSTAND THESE FIREARM SAFETY RULES - BE SURE ALL ACCESSORIES, SUCH AS HOLSTERS AND GRIPS, ARE COMPATIBLE with the firearm and that the accessories do not interfere with the safe operation. - ALWAYS USE THE CORRECT AMMUNITION FOR YOUR PARTICULAR FIREARM as indicated by the marking on the barrel or receiver. Never use non-standard, reloaded, or “handloaded” ammunition which has not been subjected to internal ballistic pressure testing. - ALWAYS HAVE ADEQUATE VENTILATION. Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Review the warning and labels for all ammunition and cleaning products carefully. YOUR SAFETY RESPONSIBILITIY - NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING. Do not use your firearm if you are on any medication which impairs, even slightly, your mental and/or physical ability. - ALWAYS WEAR EYE AND HEARING PROTECTION SPECIFIED FOR FIREARM USE every time you discharge your firearm. Make sure others in the vicinity of where you will be shooting wear protection as well. - NEVER ALLOW ANY ALTERATION OR REPLACEMENT OF PARTS IN YOUR FIREARM UNLESS PERFORMED BY AN UMAREX USA AUTHORIZED GUNSMITH. If you do otherwise, improper functioning of your firearm may occur and serious injury or death may result. - NEVER CROSS OBSTACLES SUCH AS FENCES OR STREAMS WITH A LOADED FIREARM. - Firearm safety training is available. Contact your dealer, law enforcement agency, local sportman´s club, or the NRA for availability. - APPROPRIATE USE FOR YOUR FIREARM MEANS USING YOUR FIREARM FOR LEGAL PURPOSES. 6 SAFE STORAGE & TRANSPORTATION WARNING: - You must always secure your firearm and ammunition separately so that they are not accessible to children or other unauthorized persons. - Safe and secure storage and transportation of your firearm is your responsibility. It is a full-time responsibility. - YOU SHOULD ALWAYS SECURE YOUR FIREARM IN A MANNER THAT WILL PREVENT UNAUTHORIZED ACCESS. ALWAYS STORE YOUR FIREARM UNLOADED. Your firearm and ammunition should be stored separately and in a manner inaccessible to children and unauthorized persons. - ALWAYS MAKE CERTAIN THAT YOUR FIREARM IS SAFELY SECURED IN A MANNER SO AS TO PREVENT UNAUTHORIZED ACCESS TO THE FIREARM. CARL WALTHER HAS PROVIDED A LOCK FOR THIS PURPOSE. Please read and follow the instructions for the use of this lock. There are other alternative locks and safe storage containers available in the marketplace which may be appropriate for your particular needs. Consult your local gunshop, hardware store or local police department for guidance on the variety of other safe storage devices or practices which may be appropriate for your particular needs. By purchasing this firearm you have taken on the responsibility of safely securing the firearm at all times and preventing its unauthorized use. Never assume that the use of only a lock is sufficient to safely secure your firearm. It is your personal responsibility to select and use whatever measure or practices that will best enable you to be absolutely certain that your firearm is secure at all times. YOUR SAFETY RESPONSIBILITY SAFE AND SECURE STORAGE OF YOUR FIREARM IS ONE OF THE MOST IMPORTANT RULES OF FIREARM SAFETY. YOUR FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY OR DEATH TO YOU OR OTHERS. You are responsible to determine which devices or practices are appropriate for the safe storage of your firearm and your ammunition. 7 WARNING: NEVER LOCK A LOADED FIREARM AND NEVER LOAD A LOCKED FIREARM YOUR SAFETY RESPONSIBILITIY - NEVER ASSUME THAT A ``HIDING`` PLACE IS A SECURE STORAGE METHOD. Others may be aware of your storage location or come upon it by chance. It is your personal responsibility to use common sense when storing and securing your firearm and ammunition and to always make sure that it is not accessible to children or other unauthorized persons. Always make sure your firearm is unloaded before storing. - ALWAYS FOLLOW THE LAW!! You must be familiar with all local, state, and federal laws regarding the safe discharge, storage and transportation of your firearm. Failure to know and follow the law may result in unauthorized access or use of your firearm by another. Obey all laws relating to the storage and transportation of firearms. Your local police department or gunshop will furnish you with available information on storing and/or transporting a firearm legally. - NEVER TRANSPORT A LOADED FIREARM. When transporting your firearm, be sure it is unloaded and the bolt or action is open. - YOUR FIREARM IS YOUR RESPONSIBILITY. Protect your firearm from theft or misuse by untrained or unqualified individuals. PREPARATION FOR FIRING WARNING: THE FAILURE TO FOLLOW THESE FIREARM SAFETY REQUIREMENTS WILL CAUSE SERIOUS INJURY OR DEATH TO YOU OR OTHERS. - ALWAYS WEAR ADEQUATE AND PROPER EAR PROTECTION SPECIFIED FOR FIREARM USE to prevent permanent damage to your hearing. Make sure others who are nearby are wearing ear protection as well. - ALWAYS WEAR SAFETY GLASSES SPECIFIED FOR FIREARM USE, whether indoors or out. Safety glasses should protect your eyes from the firing flash and particles associated with the discharge of ammunition. Failure to do so creates a risk of personal injury from particle or debris ejection or ricochets. 8 NEVER SHOOT AT HARD SURFACES, WATER OR UP INTO THE SKY. Always select a place to shoot that has a safe backstop and is free from obstruction and water surfaces which cause ricochets. - ALWAYS BE AWARE OF PEOPLE AROUND YOU so that persons cannot accidentally walk into the line of fire. - ALWAYS POSITION THE SHOOTER SO THAT ALL OTHERS ARE OUT OF THE LINE OF FIRE and are not within an area where they may be struck by ricochets, or by ejected cases from other types of firearms. - ALWAYS KEEP FINGERS AND OTHER PARTS OF YOUR BODY AWAY FROM THE MUZZLE AND AWAY FROM THE FIREARM BOLT AND EJECTION PORT. - ALWAYS BE ALERT AND ALWAYS FOLLOW THE SAFETY INSTRUCTIONS OF FIRING RANGE OFFICER. - ALWAYS BE SURE THAT ALL ACTIONS OF FIREARMS ARE OPEN, THAT CHAMBERS ARE CLEAR OF AMMUNITION, MAGAZINES ARE REMOVED, AND THE FIREARM IS POINTING IN A SAFE DIRECTION. - ALWAYS BE ALERT. Never shoot if you are tired, cold or impaired in any way. - ALWAYS TREAT YOUR FIREARM AS IF IT WERE LOADED. - NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING. YOUR SAFETY RESPONSIBILITY - 9 AMMUNITION A GENERAL PRINCIPLES - There are different types of ammunition for different types of firearms. Your firearm has been designed for ammunition of a specific type and a specific caliber. It is important to select the proper ammunition for your firearm. WARNING: NEVER USE AMMUNITION NOT SPECIFICALLY DESIGNATED FOR USE IN YOUR FIREARM. FAILURE TO USE THE CORRECT TYPE OR CALIBER OF AMMUNITION MAY CAUSE THE FIREARM TO JAM, FAIL TO FIRE OR EVEN GENERATE EXCESSIVE PRESSURE WHICH CAN DAMAGE OR EVEN RUPTURE YOUR FIREARM, CAUSING PERSONAL INJURY, DEATH OR PROPERTY DAMAGE. YOUR SAFETY RESPONSIBILITIY - You are responsible for selecting ammunition that meets industry standards and is appropriate in type and caliber for this firearm. - Locate the caliber designation marked on the left side of the lower receiver. This information indicates the ammunition caliber that should be used in this firearm. B HANDLOADED OR RELOADED AMMUNITION WARNING: NEVER USE NON-STANDARD, RELOADED OR ``HANDLOADED`` AMMUNITION WHICH HAS NOT BEEN SUBJECTED TO INTERNAL BALLISTIC PRESSURE TESTING. RELOADED OR HANDLOADED AMMUNITION MAY HAVE MANY MANUFACTURING AND QUALITY VARIABLES (SUCH AS THE TYPE AND AMOUNT OF GUN POWDER). ANY AMMUNITION THAT IS IMPROPERLY MANUFACTURED, EVEN IN THE SLIGHTEST DEGREE, MAY FAIL TO FIRE OR MAY GENERATE EXCESSIVE INTERNAL PRESSURES WHICH CAN DAMAGE OR EVEN RUPTURE THE FIREARM, CAUSING PERSONAL INJURY OR DEATH TO THE SHOOTER OR THOSE IN THE IMMEDIATE VICINITY. 10 - Use only commercially manufactured ammunition with internal ballistic pressure which are in strict accordance with the specifications of the Sporting Arms and Ammunition Manufacturers´ Institute (SAAMI). If you are uncertain, contact your ammunition supplier for verification. - Use only ammunition specifically recommended for your firearm. Never mix ammunition. Never use a cartridge not specifically designated for use in your firearm. Pressure from the wrong type of ammunition may exceed the capability of your firearm and may damage or even rupture your firearm. - In some cases, a round of ammunition not specified on your firearm may fit into the chamber. Firing ammunition not specified on your firearm may cause it to rupture and cause serious injury or death to you or others. - Always inspect your ammunition before using it. Never use dirty, corroded or damaged ammunition which can lead to a burst cartridge which may cause damage to the firearm and personal injury or death. WARNING: .22 L.R. CALIBER CARTRIDGES HAVE A WIDE RANGE OF LOADS, FROM LOW VELOCITY FOR SPORT SHOOTING AND MAXIMUM PRECISION TO VERY POWERFUL FOR A HIGH PROJECTILE VELOCITY. TO ENSURE RELIABLE OPERATION, A SEMI-AUTOMATIC FIREARM MUST BE MATCHED TO A CERTAIN CARTRIDGE LOAD. FOR THIS REASON THE CAL. .22 L.R. HK MP5 HAS BEEN DESIGNED FOR HIGH-QUALITY STANDARD AMMUNITION AND HV (HIGH VELOCITY) AMMUNITION, AND ONE CAN BE SURE OF TROUBLE-FREE OPERATION ONLY WITH THESE TYPES. PLEASE NOTE THAT THESE RIFLES ARE NOT DESIGNED FOR THE USE OF CAL. .22 EXTRA LONG AMMUNITION. 11 YOUR SAFETY RESPONSIBILITY C AMMUNITION SPECIFICS WARNING: fig. 1 Manual safety in “SAFE” position fig. 2 Manual safety in “FIRE” position fig. 3 Manual safety in “SAFE” position fig. 4 Manual safety in “FIRE” position ALWAYS LEAVE THE MANUAL SAFETY ENGAGED (ON “SAFE”) UNTIL YOU INTEND TO FIRE. 1 Manual Safety SAFE POSITION - turn the safety lever so it is pointing to the word “SAFE” (fig. 1). FIRE POSITION - turn the safety lever so it is pointing to the word “FIRE” (fig. 2). The safety can be operated from both sides of the firearm. Left side = fig. 1 and 2 Right side = fig. 3 and 4 WARNING: OPERATING INSTRUCTIONS NEVER RELY SOLELY ON MECHANICAL FEATURES ALONE - ALWAYS BE EXTREMELY CAREFUL, USE SAFE GUN HANDLING PRACTICES, AND AVOID SITUATIONS WHICH COULD LEAD TO AN ACCIDENT. WARNING: ALWAYS INSPECT THE CHAMBER OF YOUR FIREARM AFTER THE MAGAZINE HAS BEEN REMOVED FROM THE GUN. MAKE SURE THAT NO CARTRIDGE IS LEFT IN THE CHAMBER. 12 2 Inspection WARNING: BEFORE LOADING, MAKE SURE THAT THE FIREARM IS ALWAYS POINTED IN A SAFE DIRECTION, IS ON SAFE, AND IS UNLOADED (MAGAZINE REMOVED, CHAMBER CLEARED, EMPTY CHAMBER INDICATOR (BLUE TAB) IS INSTALLED, AND BARREL CLEAR OF ANY OBSTRUCTIONS). WARNING: NEVER PUT YOUR HAND IN FRONT OF THE MUZZLE. Functional Inspection: 1. Bolt movement: Make sure the firearm is ON SAFE, then remove the magazine and retract the bolt by pulling back the charging handle. Release the charging handle to return the bolt fully forward into battery. 2. Bolt catch: Insert the empty magazine, retract the bolt by pulling back the charging handle. The bolt locks back in rearmost position. INSPECTION 3. Decocking: Make sure that the firearm is ON SAFE and unloaded (magazine removed, chamber cleared, empty chamber indicator (blue tab) is installed, and barrel clear of any obstructions)! Pull charging handle rearward and then release allowing it to freely move forward. Place safety in the “FIRE” position, make sure the muzzle is pointed is a safe direction. Pull the trigger. The hammer drops to a de-cocked position. Put back on “SAFE”. 13 3 Loading the Firearm WARNING: BEFORE LOADING, MAKE SURE THAT THE FIREARM IS ALWAYS POINTED IN A SAFE DIRECTION, IS ON SAFE, AND IS UNLOADED (MAGAZINE REMOVED, CHAMBER CLEARED, EMPTY CHAMBER INDICATOR (BLUE TAB) IS INSTALLED, AND BARREL CLEAR OF ANY OBSTRUCTIONS). Press magazine release and remove empty magazine (fig. 5). Use the side-mounted button to push the follower down. Insert the cartridge under the magazine lips, at the same time pushing down the follower (fig. 6). Do not use excessive force. Remove empty chamber indicator (blue tab). Insert the loaded magazine until the magazine catch locks it in position (fig. 7). After inserting a magazine, always test to make sure it is locked in place by giving it a firm tap on the bottom of the magazine. fig. 5 fig. 6 4 Loading the chamber with the first cartridge Pick up the firearm with your shooting hand and point the muzzle in a safe direction. Use your other hand to retract and release the bolt with the help of the charging handle (fig. 8). Never put your hand in front of the muzzle. As the bolt travels forward it inserts the first round into the chamber. The hammer is now cocked. Leave the safety in the safe position until you are ready to fire. LOADING THE FIREARM WARNING: NEVER PUT YOUR HAND IN FRONT OF THE MUZZLE. WARNING: ALWAYS LOAD A ROUND INTO THE CHAMBER BY FEEDING IT FROM THE MAGAZINE. FAILURE TO FOLLOW THIS WARNING CAN RESULT IN SEVERE INJURY OR DEATH TO YOU OR OTHERS. NEVER ATTEMPT TO LOAD THE FIREARM BY INSERTING A ROUND INTO THE OPEN EJECTION PORT. 14 fig. 7 WARNING: fig. 8 MP5 CAL. .22L.R. ARE DESIGNED SO THAT THEY ARE ABLE TO FIRE WHEN THE MAGAZINE IS REMOVED. THEREFORE, IF THE MAGAZINE IS REMOVED FROM THE FIREARM AND THERE IS A LOADED ROUND IN THE CHAMBER, IT WILL FIRE IF THE TRIGGER IS PULLED. AFTER INSERTING A MAGAZINE, ALWAYS TEST TO MAKE SURE IT IS LOCKED IN PLACE BY APPLYING SOME REMOVAL PRESSURE TO THE MAGAZINE. WARNING: YOUR FIREARM IS NOW READY TO FIRE. KEEP YOUR FINGER OFF THE TRIGGER AND OUT OF THE TRIGGER GUARD UNTIL YOU ARE READY TO FIRE. Grasp firearm with one hand on forearm and other hand on grip with index finger resting along outside of trigger guard. Raise firearm and pull buttstock firmly into shoulder. Aim at a safe target. Move the manual safety to the fire position. Squeeze the trigger slowly and maintain the pressure until the round is fired. Your firearm loads another round immediately after firing. fig. 9 - You may continue to fire by pulling and fully releasing the trigger until the magazine is empty. - If you wish to stop, release trigger, remove finger from trigger guard, and set safety selector to “SAFE” position. If you have fired the last round from the magazine, the bolt will be held in the rearmost position so that the firearm can quickly be reloaded by replacing the empty magazine with a full magazine, or the chamber can be inspected to ensure it is empty (fig. 9). 6 Decocking - If you decide not to fire after the hammer has been cocked or if you decide to suspend firing, keep the firearm pointed in a safe direction. Remove your finger from within the trigger guard. Place the manual safety in the “SAFE” position and remove the magazine. Pull charging handle rearward to eject any remaining cartridge(s). 15 LOADING / FIRING / DECOCKING 5 Firing - Make sure that the firearm is unloaded (magazine removed, chamber cleared, empty chamber indicator fig. 10 (blue tab) installed, and barrel clear of any obstructions)! - You must be certain there is no cartridge in the chamber or obstructions in the barrel. Remember that any time you release the bolt while a magazine containing cartridges is in the firearm, you will have reloaded the firearm and it will be capable of firing. - Place the manual safety in the “FIRE” position (fig. 10). - Squeeze trigger to decock the firearm. - Place the manual safety in the “SAFE“ position. - The firearm may now be transported safely. NOTE: The gun has an internal bolt catch. To put the bolt into its forward position, remove the magazine, make sure the chamber is clear, insert the empty chamber indicator (blue tab), then retract the charging handle and release it. WARNING: KEEP THE FIREARM POINTED IN A SAFE DIRECTION WHEN DECOCKING. FAILURE TO DO THIS CAN RESULT IN SERIOUS INJURY OR DEATH. EMPTY MAGAZINE / UNLOADING 7 Firearm with Empty Magazine After the last round has been fired, the bolt catch holds the bolt in the open position (fig. 11). Place the manual safety in the “SAFE” position. fig. 11 Continue shooting - Replace the empty magazine with a full one. Pull bolt rearward and release with the help of the charging handle (fig. 8), the bolt will travel forward and load the chamber with the first round. Keep your firearm in your shooting hand, finger off the trigger and the firearm pointed in a safe direction so that there is no danger to other persons. Discontinue shooting - Remove magazine and inspect the chamber to verify it does not contain any ammunition (fig. 11). Close the bolt and decock hammer as described in section 6. 16 Manual safety in “FIRE” position 8 Unloading Point the muzzle in a safe direction. Make sure the firearm is ON SAFE. Remove the magazine. Ensure that the chamber is empty by pulling back the charging handle to visually inspect the chamber (fig. 11). Place empty chamber indicator (blue tab) into the empty chamber (fig. 23). Keep firearm pointed in a safe direction. Retract and release the charging handle so that the bolt moves into battery. Push the manual safety to the “FIRE” position (fig. 10) and squeeze trigger to decock the firearm. The firearm may now be carried safely. 9 Clearing Misfires - If a cartridge fails to fire, place the manual safety in the “SAFE” position, wait 30 seconds while keeping the muzzle pointed in a safe direction. Remove the magazine. Keep your finger off the trigger and out of the trigger guard. Grasp the bolt with the charging handle and briskly pull it fully rearward to eject the misfired round. Check the barrel chamber and bore for any obstructions by passing a cleaning rod from muzzle to ejection port. Never look down the barrel from the muzzle end. You must be certain there are no cartridges in the chamber or obstructions in the barrel. Remember that any time you release the bolt while a magazine containing cartridges is in the firearm, you will have reloaded the firearm and it will be capable of firing. WARNING: NEVER TRY TO RE-USE A MISFIRED CARTRIDGE. 17 CLEARING MISFIRES / SETTINGS WARNING: IF YOUR FIREARM GIVES ANY INDICATION THAT IT IS NOT PERFORMING PROPERLY OR THE OPERATION OF YOUR FIREARM HAS CHANGED “THE WAY IT FEELS OR SOUNDS”, STOP FIRING. MAKE SURE THE FIREARM IS POINTED IN A SAFE DIRECTION, UNLOAD THE FIREARM AND HAVE IT INSPECTED AND TEST FIRED BY A GUNSMITH QUALIFIED TO PERFORM SERVICE ON HK MP5 RIMFIRE RIFLES MADE BY CARL WALTHER. 10 Settings 10.1 Setting the Rear Sight fig. 12 The rotating rear sight drum provides four various diameter apertures. Adjusting the rear sight apertures is done by rotating the rear sight drum (fig 12). 10.2 Setting of the Rear Sight The elevation is adjusted by turning the sight drum (fig 12). Turning the drum clockwise lowers point-ofimpact and turning drum counter-clockwise raises point-of-impact. The windage is adjusted by turning the windage screw on the right side of the rear sight (fig. 13). Before adjusting the sight for windage the locking screw on top of the sight must be loosened (fig.13). After the windage adjustment is made, retighten the locking screw. Turning the windage screw clockwise moves point-of-impact left and turning counter-clockwise moves point-of-impact right. fig. 13 1. 2. 10.3 Setting of the Retractable Stock The length of the buttstock can be adjusted. Pushing the buttstock latch allows the buttstock to be positioned in either an extended or closed position (fig. 14). SETTINGS 18 fig. 14 10.4 Setting of the Bolt Speed fig. 15 The bolt speed can be adjusted for different ammunition requirements. To reach the screw for bolt speed adjustment the gun has to be disassembled as described in Section 11 Field Stripping. Only adjust the bolt speed if problems are encountered when firing a different type of ammunition. For high velocity ammunition, use the correct size Allen wrench (hex key) to increase the bolt speed by turning the screw clockwise (fig. 15). First, position the adjustment screw so that the screwhead is flush with the surrounding surface. Then, incrementally turn the screw clockwise up to a maximum of 9 complete revolutions to achieve maximum performance. Do not turn more than nine (9) turns clockwise. fig. 16 For standard ammunition, use the correct size Allen wrench (hex key) to decrease the bolt speed by turning the screw counter clockwise (fig. 15). The screwhead must never rise above “flush” with the surrounding surface. 10.5 Mounting an Optical sight To mount an optical sight you need a low profile mount (Section 18.2 Accessories). Place the low profile mount on the lugs of the upper receiver and secure it by tightening the bolts on the four clamps (fig. 16). Then place the optical sight on the mount and secure in the usual manner (fig. 17). FIELD STRIPPING fig. 17 19 11 Field Stripping WARNING: ALWAYS FOLLOW THE DISASSEMBLY INSTRUCTIONS EXACTLY. NEVER DO ANYTHING BEYOND WHAT YOU ARE SPECIFICALLY INSTRUCTED TO DO IN THIS MANUAL. NEVER ALTER OR MODIFY THE PARTS IN YOUR FIREARM. WARNING: ALWAYS WEAR EYE PROTECTION THAT IS SPECIFIED FOR USE WITH fig. 18 FIREARMS, EVERY TIME YOU HANDLE YOUR FIREARM FOR CLEANING AND MAINTENANCE. fig. 19 WARNING: PRIOR TO DISASSEMBLY, PLACE THE MANUAL SAFETY IN THE SAFE POSITION, TAKE OUT THE MAGAZINE AND CHECK THAT THE FIREARM IS NOT LOADED. To disassemble insert an empty magazine, pull back the bolt to its rearmost position with the charging handle. Remove the magazine for further disassembly. Visually inspect to verify that no ammo remains anywhere in the rifle. Push the rear receiver pin out of the gun to the right (fig. 18-19) , buttstock must be removed so that upper receiver pivots upward. FIELD STRIPPING NOTE: Further disassembly is not necessary or recommended and will void your warranty. If the compensator is removed, to reinstall: hand-tighten and then use the supplied wrench to further tighten by only 1/4 turn (fig. 20). 20 fig. 20 12 Cleaning In order to keep the firearm functional and to extend its service life, the firearm should be cleaned and maintained at regular intervals. WARNING: BEFORE CLEANING, MAKE SURE THAT THE FIREARM IS ALWAYS POINTED IN A SAFE DIRECTION, IS ON SAFE , AND IS UNLOADED (MAGAZINE REMOVED, CHAMBER CLEARED, AND BARREL CLEAR OF ANY OBSTRUCTIONS). Remove fouling from breech, magazine lips, follower, and receiver with a brush and a cloth. Clean the barrel with bore solvent and a brush and then dry it with cleaning patches; always begin at the chamber. Repeat until barrel is clean. Apply a thin coat of oil to all metal parts. Reassemble firearm and check for proper function. - Verify gun is ON SAFE. Insert EMPTY magazine and retract charging handle so that bolt assembly remains in open position. Remove magazine. Visually inspect to verify that no ammo remains anywhere in the rifle. Remove the rear receiver pin and the buttstock so that the receiver pivots upward. Thoroughly clean the bolt assembly area with a brush and cloth (aerosol gun scrubber works great) to remove powder residue and debris. Clean the barrel with bore solvent utilizing a flexible cleaning rod inserted through breech end of barrel (where bullet seats). CLEANING NOTE: Cleaning the barrel from the muzzle end requires a bore brush that does NOT exceed 1-inch in the length. Using a brush exceeding this length will result in the brush being lodged in the breech area. 21 - Apply 4 drops of gun oil to the main spring (fig. 21). Apply 1 drop of gun oil to the extractor (fig. 22). Apply 1 drop of gun oil to each end of the firing pin assembly as well as the moving parts of the buttstock. (fig. 21-22). Reassemble rifle by installing the rear pin. Wipe down exterior surface of rifle with gun oil. Insert the blue tab (empty chamber indicator), pull the charging handle rearward, then release to close the bolt assembly. fig. 21 fig. 22 MOUNTING ACCESORIES / CLEANING / STORAGE NOTE: Do not apply more oil to the recoil spring, extractor or firing pin assembly than is mentioned above. Doing so will result in an increased accumulation of powder residue which can lead to misfires and jamming issues. 13 Storage WARNING: NEVER LEAVE A LOADED FIREARM UNATTENDED! Always keep and store your firearm in an unloaded condition with the safety in the “SAFE” position. Keep the firearm and ammunition away from children and unauthorized persons. Firearms should be stored separately from ammunition. Always store your firearm with the empty chamber indicator (blue tab) in the chamber to make sure no cartridge is loaded (fig. 23). 22 fig. 23 14 Repair Do not return defective or damaged product to the dealer. If your firearm needs repair, call Umarex USA (479) 646-4210 and ask for the Service Department. WARNING: ONLY AN UMAREX USA AUTHORIZED GUNSMITH SHOULD INSPECT AND REPAIR YOUR FIREARM! 15 Warranty LIMITED ONE YEAR WARRANTY This product is warranted to the original owner for 1 year from date of purchase against defects in material and workmanship and is not transferable. WHAT IS NOT COVERED Parts, labor, and shipping charges to Umarex USA for defective product and damages caused by abuse or failure to perform normal maintenance as well as any other expense. Consequential damages, or incidental expenses, including damage to property. Umarex USA will not be responsible for unauthorized adjustments or modifications, use of defective or improper ammunition, corrosion, criminal misuse, negligence, resale, and/or use under the influence of drugs or alcohol. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Umarex USA reserves the right to determine what constitues ordinary wear and tear. WARRANTY CLAIMS Warranty Claims and Repair for U.S. customers. Call Umarex USA (479)-646-4210 and ask for the Service Department. If it is determined a return is necessary, you will be issued a Return Authorization Number. Write this number boldly on the box and return the product prepaid to Umarex USA. Your name, address, phone number and a note with the model number, serial number, and explanation of the defect found must be included in the package. Also include a copy of the original purchase receipt along with a check in the amount of $24.95, payable to Umarex USA, to cover return shipping and handling charges. 23 REPAIR / WARRANTY WHAT IS COVERED Replacement parts and labor. IMPLIED WARRANTIES Any implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to 1 year from date of retail purchase. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. TO THE EXTENT ANY PROVISION OF THIS WARRANTY IS PROHIBITED BY FEDERAL STATE, OR MUNICIPAL LAW WHICH CANNOT BE PREEMPTED, IT SHALL NOT BE APPLICABLE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY. UNDER NO CIRCUMSTANCES SHALL UMAREX USA AND CARL WALTHER GMBH BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ECONOMIC LOSS, INJURY, DEATH OR PROPERTY DAMAGE, WHETHER AS A RESULT OF BREACH OF THIS WARRANTY, NEGLIGENCE OR OTHERWISE. NOTE: All liability is excluded in the event that the instructions and warnings in this manual are not observed. WARRANTY SHIPPING GUIDELINES • Ensure that the firearm is unloaded. • Do not attempt to ship a firearm via US Postal Service; only federally licensed firearm dealers may ship a firearm by US Postal Service. • DO NOT SHIP ANY AMMUNITION. • Enclose a letter which includes your full name and address (no P.O. Boxes, please), daytime telephone number, e-mail address, the serial number of the firearm, and details of the problem experienced (stating the brand and type of ammunition used when the problem occurred) or work desired. • Record the serial number before shipping, in case you wish to check on the repair status of your firearm. • Please remove all custom parts and accessories, such as stocks, special sights and scopes, or slings from your firearm before returning. • Place the firearm in its original box and then pack it securely within another container to avoid damage. • The package must NOT bear any markings which indicate the identity of the contents. • It is recommended that shipments be insured by the owner, since Umarex USA will accept no responsibility for loss or damage in transit. • It is most important that you comply with federal, state, and local laws and regulations. The following guidelines are meant to help, but you must seek assistance from the appropriate authorities if necessary. • If your firearm must be replaced, it may be necessary to ship the replacement to a dealer rather than directly to you. You will be requested to furnish a signed FFL (Federal Firearms License) from your dealer in such an instance. 24 HECKLER & KOCH MP5 A5 HECKLER & KOCH MP5 SD6 caliber .22 L.R. HV .22 L.R. HV action blowback blowback trigger single stage trigger single stage trigger 6.5 - 8.4 lbs (2950 g - 3810 g) 6.5 - 8.4 lbs (2950 g - 3810 g) magazine capacity 25 rounds 25 rounds dimensions (L/H/W) 26.8-33.8 / 8.5 / 2.2 inch (680 - 860 / 216 / 55 mm) 26.8-33.8 / 8.5 / 2.2 inch (680 - 860 / 216 / 55 mm) barrel length 16.1 inch (409 mm) 16.1 inch (409 mm) sight radius 13.2 inch (335 mm) 13.2 inch (335 mm) 0.24/0.13/0.11/0.1 inch (6 / 3.4 / 2.9 /2.5 mm) 0.24/0.13/0.11/0.1 inch (6 / 3.4 / 2.9 /2.5 mm) 0.07 inch (1.8 mm) 0.07 inch (1.8 mm) 7 lbs (3200g) 6.7 lbs (3060 g) 2.5 ounce (70 g) 2.5 ounce (70 g) trigger pull diameter of rear sight aperture front sight width weight w/out mag magazine weight (empty) TECHNICAL DATA 16 Technical Data 25 17 Exploded view/ Parts 17.1 Exploded view EXPLODE VIEW 26 MP5 578.51.05 fake silencer 578.52.05 fake silencer SD 81 82 83 84 85 86 87 88 89 91 92 93 94 95 97 98 99 101 102 103 104 105 106 107 108 109 1 577.70.04 rear sight 5 578.10.03.1 receiver top 49 578.50.03.1 lug tube 9 576.20.39.1 system screw 51 578.40.03.1 bolt 10 578.10.01.1 receiver right 52 576.50.02 barrel USA 11 578.11.01 Back plate 19 578.11.11 buttstock 53 576.40.09.1 system screw 24 578.11.06 push pin 54 578.10.10.1 magazine release lever 26 576.20.16.3 screw nut 55 578.40.01.1 slide housing right 27 578.10.02.1 receiver left 28 578.10.06.1 magazine catch 56 578.10.11.1 bushing magazine release lever 29 578.10.08.1 magazine catch spring 57 576.40.17.0 extractor 30 578.10.07.1 magazine catch button 58 506.40.05.1 bolt for extractor 31 578.10.12.1 screw 59 576.40.25.1 spring 32 578.10.13.1 screw 60 576.40.06.3 spring adjustment screw 33 578.10.04.1 spring guiding rod 61 576.40.07.1 main spring bolt 34 578.10.05.1 spring guiding rod bolt 62 578.40.05.1 main spring 35 578.30.08.1 cocking handle spring 64 578.40.04 slide 36 578.30.03.1 cocking handle support 65 578.40.02.1 slide housing left 37 578.30.05.1 cocking handle 40 578.70.20 front sight 69 576.40.14.1 spring for slide catch front sight SD 70 576.40.15.3 pin for slide catch 44 578.30.09 push pin 71 576.40.18.1 adjustment pin 45 578.30.01.1 forearm 72 576.40.11.0 slide catch forearm SD 73 576.20.36.0 ejector cocking handle tube 74 578.20.01.1 trigger housing right cocking handle tube SD 75 578.20.07.1 bumper barrel sleeve Int. 76 576.20.28.3 pin barrel sleeve USA 77 578.20.04 hammer 576.20.14.1 578.20.05.1 578.20.06.1 576.20.29.1 578.20.10.0 576.20.15.3 576.20.04 576.20.18.3 570.20.18.1 570.20.23.3 578.20.24.3 578.20.22.1 578.20.20.1 578.20.23.1 576.20.41.1 578.20.09.2 576.40.08.3 578.20.03.0 578.20.02.1 576.10.08.3 578.20.21.3 512.20.42.1 576.100.04.1 576.20.24.3 506.20.47.3 578.60 578.61 110 578.30.11.3 111 512.50.06.2 578.50.05.2 112 578.71.22.1 muzzle nut 80 576.20.40.1 hammer spring 113 576.20.21.1 578.72.20 578.32.01.1 46 578.30.02.1 578.32.02.1 47 578.50.01.1 578.51.01.1 48 578.50.04.1 578.50.02 578.45.01.0 578.45.02.0 barrel Int. slide housing right Russia slide housing left Russla hammer spring receptor safety safety detent pin spring disconnector pin trigger sear pin spring screw nut pin safety lever right pistol grip safety lever left pin spring slide cover pin trigger trigger housing left lock washer screw simulating device Wench SW13 allen wrench SW4 allen wrench SW2.5 SA magazine 25 rd SA magazine 10 rd Roll pin O-Ring O-Ring Front sight post 2 disconnector spring DESIGNATION 17.2 Parts 27 18 Variants and accessories 18.1 Variants MP5 A5 • Metal Receiver • Retractable Stock • Adjustable Rear Sight (Windage, Elevation) MP5 SD6 • Metal Receiver • Adjustable Rear Sight (Windage, Elevation) • Retractable Stock VARIANTS 28 18.2 Accessories MP5 Magazine Sling Swivel 10 Round 25 Round 2245331 2245310 2245311 Fixed Stock Walther PS 55 Scope 2245332 2300580 RIS for MP5 A5 Walther PS 22 Point Sight 2245330 2300577 Low Profile Mount 2245334 MP5 ACCESSORIES HK .22 LR Forearm Grip 2245333 29 HK MP5 .22 Rimfire Rifles made by Carl Walther - Germany under license from Heckler & Koch Distribution and repair service by: This INSTRUCTION MANUAL should always accompany the firearm and be transferred with it upon change of ownership or when presented to another person. A copy of the INSTRUCTION MANUAL is available FREE upon request from: CONTACT UMAREX USA Inc. www.umarexusa.com www.hk22rimfire.com Sales + Warranty Service 7700 Chad Colley Boulevard / Fort Smith, AR 72916 / USA Phone: 479-646-4210 / Fax: 479-646-4206 All technical changes and modifications reserved. 8.578.80.02 rev. D July 2011
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : drewes Create Date : 2011:07:07 11:56:40+02:00 Modify Date : 2011:07:07 11:56:40+02:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Manual 8.578.80.02.indd Creator : drewes Document ID : uuid:e651a4ae-d882-48dd-9190-4ad72bbbfa62 Instance ID : uuid:f5421217-19dc-446e-a240-df9c7451fe47 Page Count : 30EXIF Metadata provided by EXIF.tools