GRANDVIEW GV230 Manuel LENNOX 230

User Manual: GRANDVIEW GV230

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

INSTALLATION AND OPERATION MANUAL

Free-Standing
EPA Certified
Wood-Burning Stoves
Save These Instructions
For Future Reference
P/N 506031-01, Rev. F, 07/2013

Wood-Burning Stoves
Models Grandview™
GV230 and GV300

P506031-01

With Innovative Thermal Fin Technology (TFT™)

A French manual is available upon request. Order P/N 506223-28.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 506223-28.

This appliance must be properly installed and operated in order to prevent the
possibility of a house fire. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow these
instructions could result in property damage, bodily injury or even death.
Contact your local building or fire officials to obtain a permit and
information on any installation requirements and inspection
requirements in your area.
4002589

WARNING
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.

CONGRATULATIONS!

Pedestal Installation...................................................................... 15
Attaching Stove to Manufactured Home Floor - GV230 ................ 16

When you purchased your new wood stove, you joined the ranks of
thousands of individuals whose answer to their home heating needs
reflects their concern for aesthetics, efficiency and our environment. We
extend our continued support to help you achieve the maximum benefit
and enjoyment available from your new wood stove.

Outside Combustion Air Kit Installation........................................ 17

Thank you for selecting a Lennox Hearth Products wood stove as the
answer to your home supplemental heating needs.

Paint Curing.................................................................................. 21

Brick and Baffle Board Installation - GV230 ................................. 18
Brick and Baffle Board Installation - GV300 ................................. 19
For Mobile Home Installs.............................................................. 20
Post Installation Checks................................................................ 20
Burn-In Period.............................................................................. 21
Operating Hints............................................................................. 21

TABLE OF CONTENTS

Door Operation............................................................................. 21
Starting and Maintaining a Fire................................................22-23
Fuel .... .......................................................................................... 23

Using This Manual.......................................................................... 2

Getting the Most Out of Your Stove.............................................. 24

Important Safety Information.......................................................... 3

Maximizing Your Stove’s Overall Efficiency................................... 24

Testing Information......................................................................... 4

Achieving Clean, Long Burns........................................................ 24

Draft Requirements......................................................................... 4

Blower Operation (optional kit) .................................................... 25

Selecting the Proper Venting System.............................................. 4

Do’s and Don’ts............................................................................. 26

Chimney Height Requirements........................................................ 5

Maintenance............................................................................ 26-27

Negative Pressure Warning ............................................................ 5

Troubleshooting............................................................................ 28

Clearances to Combustibles - GV230 ............................................. 7

Replacement Parts Lists............................................................... 29

Clearances to Combustibles - GV300 ............................................. 8

Accessories.................................................................................. 31

Floor Protection.........................................................................6-10

Product Reference Information..................................................... 32

Alcove, Floor Protection - GV230.................................................... 9
Alcove, Floor Protection - GV300.................................................. 10
Specifications ............................................................................... 11
Typical Installation Figures............................................................ 12
Chimney Installation..................................................................... 13
Manufacture (mobile) Home Installations..................................... 13
Chimney - Wall Pass-Through Requirements............................... 14
Leg Installation............................................................................. 15

USING THIS MANUAL
Please read and carefully follow all of the instructions found in this
manual. Please pay special attention to the safety instructions provided
in this manual.

PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE

17.

18.

19.
20.
21.

22.

23.

24.
25.
26.
27.

Safety and
and General
General
Planning Installation Safety
Installation

16.

Operation

15.

Maintenance

1. When this room heater is not properly installed, a house
fire may result. To reduce the risk of fire, follow the installation instructions. Contact local building or fire officials
about restrictions and installation inspection requirements
in your area.
2. Wear gloves during installation to avoid injury from sharp
edges on the stove and/or its parts.
3. This unit is designed and engineered to burn only dry, wellseasoned wood. Burning wet wood will greatly reduce the
stove’s efficiency, produce excessive amounts of smoke
and can cause dangerous chimney fires due to creosote
build-up.
4. Before opening the door, the draft control must be fully open
to avoid possible combustion flash (ignition of hot volatile
gases as the door is opened).
5. Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or ’freshenup’
a fire in this heater. Keep all such liquids well away from
the heater while it is in use. DO NOT USE CHEMICALS OR
FLUIDS TO START THE FIRE.
6. While burning, fuel utilizes oxygen from the air in the room.
Be sure to allow an adequate amount of fresh air into the
room where the stove is burning.
7. The outside surface of the stove will be hot while burning
properly and can set items like clothing and curtains on
fire. Keep furnishings and other combustible materials
away from the stove. Using the heat from the stove to dry
wet clothing can be hazardous if clothes are placed too
near the surface of the stove.
8. HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING
FURNISHINGS AND COMBUSTIBLE MATERIAL A CONSIDERABLE DISTANCE AWAY. CONTACT MAY CAUSE SKIN BURNS.
Do not allow children to play near the stove without close
supervision. Do not touch the stove while it is burning.
Use extreme caution while the unit is in use. Surface temperatures become dangerously hot and can cause serious
burns.
9. Do not allow anyone to operate the stove who is not familiar
with the operating instructions.
10. Attempts to achieve heat output rates that exceed stove
design specifications can result in permanent damage to
the stove. Never leave your stove unattended on high burn
rates. This may cause overfiring. Overfiring the stove may
cause a house fire. If the stove glows, you are overfiring.
11. Keep a water hose or hand-operated fire extinguisher close
for safety.
12. Smoke Detectors - Since there are always several potential sources of fire in any home, we recommend installing
smoke detectors. If possible, install the smoke detector in
a hallway adjacent to the room (to reduce the possibility
of occasional false activation from the heat produced by
the stove). If your local code requires a smoke detector
be installed within the same room, you must follow the
requirements of your local code. Check with your local
building department for requirements in your area.
13. Inspect your chimney at least once a month during the burn-

14.

Troubleshooting

read THIS MANUAL IN ITS ENTIRETY and understand these Rules to follow for safety.

ing season to check for soot and creosote accumulations.
Any accumulations over 1/8” thick should be removed by
a professional chimney sweep. Do not attempt to burn out
heavy creosote accumulations with a hot fire. If large accumulations are occurring, review your burning procedures.
If a creosote fire should develop, the fire department should
be called immediately and then attempts should be made
to control the fire until assistance arrives. If a “runaway”
fire should develop causing over-heating of the stove, the
door and draft regulators should be closed immediately.
The fire should die down once deprived of oxygen. After a
severe chimney fire, the complete chimney system should
be checked before further use.
Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly
On Hearth (firebrick). Do not use andirons or other methods
of supporting the fuel.
Please read this entire manual before you install and use
your new room heater. Failure to follow instructions may
result in property damage, bodily injury, or even death.
Check all local building and safety codes before installation.
The installation instructions and appropriate code requirements must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
In the U.S.A, install in accordance with the National Fire
Protection Association’s Code, NFPA 211, Standards for
Chimneys, Fireplaces, Vents and Solid-Fuel-Burning Appliances, or similar regulations, may apply to the installation
of a Solid-Fuel-Burning appliance in your area. In Canada,
the guideline is established by the CSA Standard, CAN/
CSA-B365-M93, Installation Code for Solid-Fuel-Burning
Appliances and Equipment.
DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY
AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY
APPROVED FOR SUCH INSTALLATIONS.
WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH
MAY LEAD TO DEATH!
Carbon Monoxide Poisoning - Early signs of carbon monoxide poisoning resemble the flu with headaches, dizziness,
or nausea. If you have these signs, get fresh air at once!
Have the heater inspected by a qualified service technician.
Some people are more affected by carbon monoxide than
others. These include pregnant women, people with heart
or lung disease or anemia, those under the influence of
alcohol, and those at high altitudes.
Failure to use manufacturer provided parts, variations in
techniques and construction materials or practices other than
those described in this manual may create a fire hazard and
void the limited warranty.
Do not make any make-shift compromises during installation. Any modification or alteration may result in damage
to the appliance or dwelling and will void the warranty,
certification and listings of this unit.
These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate heat source
when installed in a dwelling.
Do Not Overfire - If Heater or Chimney Connector Glows,
You Are Overfiring.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH
AS GASOLINE, NAPHTHA OR ENGINE OIL.

Parts / Accessories

IMPORTANT SAFETY AND WARNING
INFORMATION

Testing Information
This manual describes the installation and operation of the Grandview™
230 and Grandview 300 non-catalytic wood heaters. This heater meets
the U.S. Environmental Protection Agency’s emissions limits for wood
heaters sold on or after July 1, 1990. This heater has been developed,
tested and constructed in accordance with the requirements of UL 1482,
ULC S627 and HUD standards and is listed by Intertek Testing Services,
Portland, OR. It has been approved for residential, mobile home and
alcove installations.

Draft Requirements
This appliance is dependent upon a properly functioning chimney for
optimum performance. It is a high efficiency appliance that loses much
less heat up the chimney than older appliances and fireplaces. For this
reason it is important to match the stove to the chimney. The chimney
has two functions:
1. It draws combustion air into the appliance (without air, no fuel will
burn) and
2. It exhausts combustion by-products. Your new Country® Collection
stove is what is known as a “natural draft” appliance.
The appliance depends solely on the natural draft of the chimney system
to draw combustion air into the unit. Draft is the force that moves air
from the appliance up into the chimney. The amount of draft in your
chimney depends on the length of the chimney, local geography, nearby
obstructions and other factors. Too much draft may cause excessive
temperatures in the appliance (overfiring). Slow or inadequate draft
equals poor combustion and possible smoking problems. The following
are some conditions that may contribute to poor chimney draft:
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate draft.
3. A chimney with excessive height (this may allow exhaust to cool too
much before exiting, which will stall the rate the exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney Guidelines).
Inadequate draft will cause the appliance to leak smoke into the room
through the stove and the chimney connector joints.
Excessive draft may cause an uncontrollable burn or a glowing red stove
or chimney part.
Overfiring Damage - If the heater or chimney connector glows, you are
overfiring. Other symptoms may include: Cracking, warping or burning
out of components, plated accessories may turn color, stove glass may
develop a haze, which will not come off with cleaning.
Overfiring of a stove is a condition where excessive temperatures are
reached, beyond the design capabilities of the appliance. The damage
that occurs from overfiring is not covered under the manufacturer’s
limited warranty.
Also see Troubleshooting on Page 28.

Selecting the Proper Venting System
The appliance is merely one component of a larger system. The other
equally important component is the venting system. This is necessary for
achieving the required flow of combustion air to the fire chamber and for
safely removing unwanted combustion by-products from the appliance.
If the venting system’s design does not promote these ends, the system
may not function properly. Poorly functioning venting systems may create
performance problems as well as be a safety hazard. A draft test should
read greater than .04’ W.C. (inches water column) and less than .08”
W.C. As per NFPA-211 standard (see paragraph below), the installer
must take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements of the
appliance. See Chimney Guidelines below to assist you in selecting the
proper venting system for your installation.
American National Standards Institute ANSI/NFPA 211, Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances - See
Draft Section: A chimney or vent shall be so designed and constructed
to develop a flow sufficient to completely remove all flue and vent gases
to the outside atmosphere. The venting system shall satisfy the draft
requirements of the connected appliance in accordance with the manufacturer’s instructions.
Chimney Guidelines:
• This appliance requires approximately 12 feet minimum of “effective
draw” provided by the venting system. As a rule of thumb, every 90
degree total direction change in the venting will result in a loss of
approximately 5 feet of “effective draw.” Example: If two 45 degree
offsets are used, subtract 5 feet from the actual vertical vent height
to determine your “effective draw.” In this case if you had 14 feet of
vertical vent, the effective draw would only be approximately 9 feet
(14 ft. - 5 ft. = 9 ft.), therefore it may be necessary to add additional
height to the venting system.
• Do not install an offset within the first two feet above the flue outlet
on the appliance.
• In well insulated and weather tight homes, it may be difficult to establish
a good draft up your chimney. The poor draft is caused by a shortage
of air in the house. In this situation an Outside Air Kit may need to
be installed (See Negative Pressure Warning on Page 5 and Outside
Combustion Air on Page 17).

(914 mm)

Min.

Figure 1 - Chimney Height Requirements
To pass inspection in nearly any jurisdiction, the chimney must meet both
safety and exhaust flow requirements. The (3’ by) 2’ by 10’ rule applies
to both masonry and factory-built chimneys.
* Ref. USA - National Standard, NFPA 211-latest edition and Canada
National Standard CSA B365-01-latest edition. Vents installed with a
listed cap shall terminate in accordance with the terms of the cap’s
listings.

Ventilation Requirements - Provide adequate air for combustion. The
fresh air requirements of this appliance must be met within the space
where it will be installed. Ventilation is essential when using a Solid-FuelBurning heater. In well insulated and weather tight homes, it may be
difficult to establish a good draft up the chimney (caused by a shortage
of air in the home). The lack of air is caused by many common household
appliances which exhaust air from the home (such as a furnace, heat
pump, air conditioner, clothes dryer, exhaust fans, fireplaces, and other
fuel burning appliances). Also, the combustion process of this heater
uses oxygen from inside the dwelling. If the available fresh air delivery
in the dwelling is insufficient to support the demands of these appliances,
problems can result (e.g. excessive negative pressure can develop in the
dwelling which will affect the rate at which this appliance can draft thus
resulting in performance problems). To correct this problem it may help
to open a window (preferably on the windward side of the house) or install
an optional outside air kit.

Installation

10'
(3 m)

Operation

3' (914 mm)
Min.

Maintenance

2’ (610 mm) Min.

Troubleshooting

Less than
10' (3 m)

This appliance is not designed to be operated in a negative pressure.
In very airtight homes with large kitchen exhaust fans, furnace cold air
returns, fresh air exchange systems and any other air system in close
proximity to the heating appliance may create a negative pressure in the
same room as the heating appliance. This can create dangerous back
drafting of the stove and chimney joints, drawing combustion by-products
into the home. Be sure your home has adequate makeup air to eliminate
negative pressures caused by the above-mentioned sources. Outside air
connected to the appliance probably will not resolve such a problem as
the stove or fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from negative
pressures described here.

Parts / Accessories

The chimney must extend 3’ (.92m) above the level of roof penetration
and a minimum of 2’ (.61m) higher than any roof surface within 10’
(3m) (see below). Check with your local building officials for additional
requirements for your area.

Planning
Planning Installation
Installation Safety and General

Negative Pressure Warning

Chimney Height Requirements

Clearances to Combustibles
WARNING: BE ABSOLUTELY SURE THE DISTANCE BETWEEN
THE HEATER AND THE SURFACE OF ANY COMBUSTIBLE CONSTRUCTION IS NOT LESS THAN SHOWN IN THE FIGURES ON
PAGE 7 FOR MODEL GV230 WOODSTOVE AND ON PAGE 8 FOR
MODEL GV300 WOODSTOVE.
Floor Protection
USA - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 16” in front of the
door opening of the heater and 8” to either side of the door opening.
Canada - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 450 mm in front of
the door opening of the heater and 200 mm to either side of the stove
body and 200 mm to the rear or to the wall, whichever is smaller.
USA and Canada - A chimney connector / venting extends horizontally
over the floor, protection must also cover the floor under the connector
/ venting and at least 2” (51 mm) to either side.
Alcove Installations USA and Canada - The floor protection must be a
thermally rated non-combustible floor protector. See Page 9 for GV230
stoves or Page 10 for GV300 stoves for details on determining acceptable floor protection materials or hearth pads for alcove installations.

Alcove Installation
Clearances - In alcove installations, only 6” double wall connector pipe
can be used (single wall or single wall pipe with shield is not allowed).

Chimney and Connector
Minimum 6" diameter, minimum 24 MSG black steel connector pipe with
UL103HT listed factory-built chimney suitable for use with solid fuels
or masonry chimney. Horizontal connection not tested, refer to local
building codes for installation. See installation instructions for details.
Restrictions apply! Read instructions before installing.
Residential chimney systems must be from the same brands as listed
for mobile homes but connector pipe may be double wall, single wall,
or single wall with shield as listed.
This appliance may be vented into a code-approved masonry chimney
with flue liner.
WARNING: CHIMNEY CONNECTOR MUST BE IN GOOD CONDITION AND
KEPT CLEAN. DO NOT INSTALL DAMAGED PARTS.
All of the stove connector pipe used must be of the same brand. The
chimney that the stove pipe transitions into may be a different brand.
Other than the transition of the stove pipe into the chimney, do Not mix
different brand vent components. Install all vent components per vent
manufacturer’s instructions.
The chimney connector shall not pass through an attic or roof space,
closet or similar concealed space, or a floor, or ceiling. Where passage
through a wall, or partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365, Installation Code for SolidFuel-Burning Appliances and Equipment.
There must be an effective vapor barrier at the location where the chimney
or other component penetrates to the exterior of the structure. Follow
the vent manufacturer's detailed instructions.

Minimum alcove width between combustible materials:
GV230 - 52” (1321 mm)
GV300 - 54” (1372 mm)

IMPORTANT NOTE: See Draft Requirements and Selecting a Proper
Venting System on Page 4 to assist you in choosing the proper venting
system for your installation.

Maximum alcove depth:
GV230 and GV300 - 48” (1219 mm)

Clearance dimensions are to flue collar. If a single wall connector pipe
with shield is used, a 1 inch air space is needed between pipe and shield.
Shield attaches to rear of stove pipe and must run from stove top to
ceiling. Pipe shield shall be UL listed.

Minimum alcove height:
GV230 and GV300 - 72” (1829 mm)
Thermal Floor Protection

Components Required For Installations

GV230 - Thermal floor protection is only required where the stove is
installed into an alcove.

Legs OR Pedestal Assembly.

GV300 - Thermal floor protection is required in all installations.

Use all required components specified for this appliance. Do
not substitute.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Note: The cover
plate is not necessary if a blower has never been installed
because a knock-out will be in place to act as the cover.

Installation Clearances - Refer to FIGURES 2, 3 AND 4

Alcove Depth
48" (1219mm) MAX.

†A

Combustible
Wall

D
H

Stove

USA

Elbow

G F

F G

E†

Alcove

Floor
Protection

Stove

E†

USA

Stove

Floor
Protection

Installation

Floor
Protection

Elbow

Combustible Wall

Combustible Wall
B

Corner Installation

Alcove or Parallel Installation

Planning Installation Safety and General

Grandview™ GV230

Top View
I

Top View

Figure 4 - GV230

USA - inches (millimeters)
B (1)

C (3)

D (1)

E (8)

F (1,4) G(3,4)

H (2)

I (6)

J (2)

K (7)

L (5)

T (6)

Single Wall Residential-Vertical Vent

16 12-3/8
(406) (314)

22
(559)

12-1/2

8
5-11/16 16
(200) (145) (406)

38-5/8
(981)

51
(1295)

33
(838)

16
(406)

0
(0)

84
(2134)

58-7/8
(1495)

N/A
N/A

Single Wall Residential-With Elbow

19 15-3/8
(483) (391)

23
(584)

13-1/2

8
5-11/16 16
(200) (145) (406)

38-5/8
(981)

54
(1372)

33
(838)

16
(406)

0
(0)

84
(2134)

58-7/8
(1495)

19
N/A

10 6-3/8
Double Wall Residential or Mobile Home-Vertical Vent

(254) (162)

20
(508)

10-1/2

8
4-11/16 15
(200) (119) (381)

38-5/8
(981)

45
(1143)

33
(838)

16
(406)

0
(0)

84
(2134)

57-1/2
(1461)

N/A
N/A

Double Wall Residential or Mobile Home-With Elbow

10 6-3/8
(254) (162)

21
(533)

11-1/2

(292)

8
4-11/16 15
(200) (119) (381)

38-5/8
(981)

45
(1143)

33
(838)

16
(406)

0
(0)

84
(2134)

57-1/2
(1461)

10
N/A

Double Wall Alcove-Vertical Vent

13 9-3/8
(330) (238)

22-1/2
(572)

13
(330)

8
(200)

38-5/8
(981)

48
(1219)

33
(838)

16
(406)

0
(0)

72
(1829)

N/A
N/A

A (3)

E (8)

PIPE

INSTALLATION

A (3)

(318)

(343)

(267)

N/A
N/A

CANADA - inches (millimeters)
B (1)

C (3)

D (1)

F (1,4) G(3,4)

H (2)

I (6)

J (2)

K (7)

L (5)

T (6)

Single Wall Residential-Vertical Vent

16 12-3/8
(406) (314)

22
(559)

12-1/2
(318)

8
5-11/16 16
(200) (145) (406)

49
(1235)

53
(1346)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

58-7/8
(1495)

N/A
N/A

Single Wall Residential-With Elbow

19 15-3/8
(483) (391)

23
(584)

13-1/2

(343)

8
5-11/16 16
(200) (145) (406)

49
(1235)

56
(1422)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

58-7/8
(1495)

19
(483)

10 6-5/16
Double Wall Residential or Mobile Home-Vertical Vent

(254) (160)

20
(508)

10-1/2
(267)

8
4-11/16 15
(200) (119) (381)

47
(1193)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

57-1/2
(1461)

N/A
N/A

8
4-11/16 15
(200) (119) (381)

47
(1193)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

57-1/2
(1461)

10
(254)

49
(1235)

50
(1270)

41-1/8
(1045)

18
(450)

8
72
(200) (1829)

N/A
N/A

PIPE

INSTALLATION

Double Wall Residential or Mobile Home-With Elbow

10 6-5/16
(254) (160)

21 11-9/16
(533) (293)

Double Wall Alcove-Vertical Vent

13 9-3/8
(330) (238)

22-1/2 13-1/16
8
(572) (331) (200)

Footnotes:
1- These dimensions to the stove body are for reference
only. Actual distances should be measured from the
stove’s flue collar.
2- Minimum noncombustible hearth pad dimensions.
3- Clearances to connector pipe shall be measured from
the flue collar of the stove.
4- Not applicable to alcove installations.

N/A
N/A

5- In corner applications, when installed at minimum
back wall clearances, the required floor protection
is dimensioned off the back plane of the stove,
therefore the floor protection required off the
back corners (at a 45 degree angle) only needs to
extend to the wall. This situation will only occur in
CANADA installations.

Operation

Figure 3 - GV230

Maintenance

Figure 2 - GV230

Side View

Troubleshooting

Canada

Parts / Accessories

† See note 8

6- Reference dimension only, to assist in planning the
installation.
7- Measured from front of floor protection to the front of
firebox.
8- USA=8” (200mm) from door opening, Canada=8”
(200mm) from sides and back of unit.

7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Grandview™ GV300

Installation Clearances - Refer to FIGURES 5, 6 AND 7

Alcove Depth
48" (1219mm) MAX.

Floor
Protection

†A

Combustible
Wall

L
U

C
D
H

Stove

Elbow

G F

F G

E†
USA

Alcove

Elbow

Combustible Wall

Combustible Wall
B

Corner Installation

Alcove or Parallel Installation

Floor
Protection

Stove

E†
USA

Stove

Floor
Protection

Top View
† See note 8

Canada

Figure 5 - GV300

Figure 6 - GV300

Side View

Figure 7 - GV300

USA - inches (millimeters)
PIPE

INSTALLATION

Single Wall Residential-Vertical Vent

A (3)

B (1)

C (3)

16 12-3/8 25-1/8
(406) (314) (635)

D (1)

E (8)

H (2)

I (6)

J (2)

K (7)

L (5)

T (6)

8
(200)

6
(152)

17
(432)

41-1/8
(1045)

53-1/2
(1359)

33
(838)

16
(406)

0
(0)

84
(2134)

62-7/8
(1597)

N/A
N/A

8
(200)

6
(152)

17
(432)

41-1/8
(1045)

57-1/8
(1451)

33
(838)

16
(406)

0
(0)

84
(2134)

62-7/8
(1597)

19
N/A

8
(200)

5
(127)

16
(406)

41-1/8
(1045)

49-1/8
(1248)

33
(838)

16
(406)

0
(0)

84
61-7/16
(2134) (1561)

N/A
N/A

8
(200)

5
(127)

16
(406)

41-1/8
(1045)

49-1/8
(1248)

33
(838)

16
(406)

0
(0)

84
61-7/16
(2134) (1561)

10
N/A

N/A
N/A

41-1/8
(1045)

51-1/8
(1299)

33
(838)

16
(406)

0
(0)

72
(1829)

N/A
N/A

(381)

F (1,4) G(3,4)

19-5/8 16
(499) (406)

26-1/8
(664)

(406)

11-5/8 8
Double Wall Residential or Mobile Home-Vertical Vent

(295) (203)

23-1/8
(587)

(330)

Double Wall Residential or Mobile Home-With Elbow

11-5/8 8
(295) (203)

24-1/8
(613)

(356)

Double Wall Alcove-Vertical Vent

13-5/8 10
(346) (254)

26-1/8
(664)

(406)

8
(200)

A (3)

C (3)

D (1)

E (8)

H (2)

I (6)

J (2)

K (7)

L (5)

T (6)

8
(200)

6
(152)

17
(432)

51-1/8
(1299)

55-1/2
(1410)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

64-7/8
(1648)

N/A
N/A

8
(200)

6
(152)

17
(432)

51-1/8
(1299)

59-1/8
(1502)

41-1/8
(1045)

18
(450)

8
84
(200) (2134)

64-7/8
(1648)

19
(483)

8
(200)

5
(127)

16
(406)

51-1/8
(1299)

41-1/8
(1045)

18
(450)

8
84
63-7/16
(200) (2134) (1611)

N/A
N/A

8
(200)

5
(127)

16
(406)

51-1/8
(1299)

41-1/8
(1045)

18
(450)

8
84
63-7/16
(200) (2134) (1611)

10
(254)

8
(200)

N/A
N/A

51-1/8
(1299)

53-1/8
(1349)

41-1/8
(1045)

18
(450)

8
72
(200) (1829)

Single Wall Residential-With Elbow

CANADA - inches (millimeters)
PIPE

Top View

INSTALLATION

B (1)

Single Wall Residential-Vertical Vent

16 12-3/8 25-1/8
(406) (314) (635)

(381)

Single Wall Residential-With Elbow

19-5/8 16
(499) (406)

26-1/8
(664)

(406)

11-5/8 8
Double Wall Residential or Mobile Home-Vertical Vent

(295) (203)

23-1/8
(587)

(330)

Double Wall Residential or Mobile Home-With Elbow

11-5/8 8
(295) (203)

24-1/8
(613)

(356)

Double Wall Alcove-Vertical Vent

13-5/8 10
(346) (254)

26-1/8
(664)

(406)

F (1,4) G(3,4)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

N/A
N/A

Grandview™ GV230

Methods of determining floor protection equivalents:
To determine the thickness required for the alternate material when
either the "k" value or "r" value is known, use either the k formula or r
formula.
Example: If Micore 160 Mineral Fiber Board is to be used for the
floor protection, how thick must this material be?

kL = k value per inch of listed material
rL = r value per inch of listed material
TL = minimum thickness of listed material

TM (inches) =

.312 (inches)=

k formula:
k-value (per Inch) of
alternate material (kM) x
k-value (per inch)
of listed material (kL)

Specified min.
thickness
of listed
material (TL)

TM (inches) =

*.47

TM (inches) =

*.35
*.47

.50"

.312 (inches)=

.745

.50"

Answer - The minimum required thickness of the Micore 160 is .372"
therefore round up to nearest standard thickness available which is
3/8” (.375”)

*2.13
*2.86

.50"

.745

.50"

Answer - The minimum required thickness of the Micore 160 is .372"
therefore round up to nearest standard thickness available which is
3/8” (.375”)

Listed Material

.47
KL

r (per inch)
2.13
rL

Installation

Listed Material
k (per inch)

Listed Min. Thickness
1/2" (.50")
TL

** Approved Alternate Materials for Floor/Hearth Protection
Alternative Materials

Thermal Values
k (per inch)
KM

r (per inch)
rM

Minimum Thickness

(rounded to nearest 1/8 inch)

Min. Thickness
TM

Kaowool M Board

.47

2.13

.5" (1/2")

Micore 160™

.35

2.86

.37" (3/8")

Micore 300™

.46

2.17

.49" (1/2")

Durock™ Cement Board

1.92

.52

2.04" (2-1/8")

Hardibacker™

1.95

.51

2.07" (2-1/8")

Hardibacker 500™

2.30

.43

2.45" (2-1/2")

Cultured Stone Hearthstone™

2.82

.35

3" (3")

Wonderboard

3.23

.31

3.44" (3-1/2")

Super Firetemp M

.61

1.64

.65" (3/4")

Super Firetemp L

.54

1.85

.57" (5/8")

Face brick

9.00

.111

9.57" (9-5/8")

U.S. Gypsum
U.S. Gypsum

Johns-Manville

Note: An asterisk "*" indicates, it is a value taken from Table 1.
Using the k formula:

Minimum
thickness of
=
alternate
material (TM)

U.S. Gypsum

kM = k value per inch of alternate material
rM = r value per inch of alternate material
TM = minimum thickness required for alternate material
TS = standard thickness of the alternate material

TM (inches) =

Specified min.
thickness
of listed
material

Johns-Manville

Common brick

5.00

.20

5.32” (5-3/8")

Cement mortar

5.00

.20

5.32” (5-3/8”)

Ceramic tile

12.5

.08

13.30" (13-3/8")

Marble

~11

~.09

11.70" (11-3/4")

Operation

Note: Any noncombustible material having a minimum thickness of
1/2”(12.7mm) whose k value is less than .47 or whose r value is more
than 2.13 is acceptable. If the alternate material used has a higher k value
or lower r value will require a greater thickness of the material used. In
some cases, if the k value is less or the r value higher, a thinner material
may be used.

r-value (per Inch)
of listed material
x
r-value (per inch)
of alternate material

Maintenance

The floor protection or alternate material used as a floor protector must
be constructed of a durable noncombustible material having an equal or
better thermal conductivity value (lower k value) of k =.47 BTU/IN FT2 HR
°F or a thermal resistance that equals or exceeds r = 2.13 HR °F FT2 IN/
BTU with a minimum thickness of 1/2”. With these values, determine the
minimum thickness of the alternate material required using the formula(s)
and shown in Table 1.

Minimum
thickness of
=
alternate
material

Troubleshooting

Using Alternate Material As Floor Protection

Using the r formula:

Table 1 - USA AND CANADA REQUIREMENTS - GV230

Parts / Accessories

When the Grandview™ 230 is installed in an Alcove, the floor protection
must be a thermally rated non-combustible floor protector meeting or
exceeding a thermal rating of k=.47 or equivalent with a listed thickness
of 1/2" (12.7 mm) minimum in the USA and Canada. The thermal protection must extend 16” in front of the heater and 8” to each side (measured
from the door opening).

Planning Installation Safety and General

ALCOVE INSTALLATIONS - FLOOR Protection

** If the hearth extension material(s) that is intended to be used is NOT
listed on Table 1, the material can still be used if the material(s) is noncombustible. However, the manufacturer of the material must provide
either the listed k-value per inch or r-value per inch with listed thickness
so that the minimum thickness required for the hearth can be calculated
(per instructions here or as specified in the NFI Certification Manuals).
Note: Also see NFI (National Fireplace Institute) Certification Manuals showing other acceptable calculation methods and acceptable alternate materials
which can be used.

9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Grandview™ GV300

FLOOR Protection

The Grandview™ 300 floor protection must be a thermally rated noncombustible floor protector meeting or exceeding a thermal rating of
k=.47 or equivalent with a listed thickness of 1-1/2" (38.1mm) minimum
in the USA and Canada. The thermal protection must extend 16” in front
of the heater (measuring from the front of the firebox) and the the width
of the heater (26-1/2”).
Using Alternate Material As Floor Protection
The floor protection or alternate material used as a floor protector must
be constructed of a durable noncombustible material having an equal
or better thermal conductivity value (lower k value) of k =.47 BTU/IN
FT2 HR °F or a thermal resistance that equals or exceeds r = 2.13 HR
°F FT2 IN/BTU with a minimum thickness of 1-1/2”. With these values,
determine the minimum thickness of the alternate material required using
the formula(s) and shown in Table 2.
Note: Any noncombustible material having a minimum thickness of
1-1/2” (38.1 mm) whose k value is less than .47 or whose r value is
more than 2.13 is acceptable. If the alternate material used has a higher
k value or lower r value will require a greater thickness of the material
used. In some cases, if the k value is less or the r value higher, a thinner
material may be used.
Methods of determining floor protection equivalents:
To determine the thickness required for the alternate material when
either the "k" value or "r" value is known, use either the k formula or r
formula.

Using the r formula:
Minimum
thickness of
=
alternate
material

kM = k value per inch of alternate material
rM = r value per inch of alternate material
TM = minimum thickness required for alternate material
TS = standard thickness of the alternate material

TM (inches) =

1.117 (inches)=

k formula:
Minimum
thickness of
=
alternate
material (TM)

k-value (per Inch) of
alternate material (kM) x
k-value (per inch)
of listed material (kL)

Specified min.
thickness
of listed
material (TL)

TM (inches) =

*.47

TM (inches) =

*.35
*.47

1.50"

1.117 (inches)=

.745

1.50”

Answer - The minimum required thickness of the Micore 160 is 1.117"
therefore round up to nearest total standard thickness - Example: Use
two 5/8” (.625”) boards for a total thickness of 1-1/4” (1.250”).

*2.13
*2.86

1.50"

.745

1.50”

Listed Material
k (per inch)
Listed Material

.47
KL

r (per inch)
2.13
rL

Listed Min. Thickness
1-1/2" (1.5")
TL

** Approved Alternate Materials for Floor/Hearth Protection
Alternative Materials

Thermal Values

Minimum Thickness

(rounded to nearest 1/8 inch)

k (per inch)
KM

r (per inch)
rM

Min. Thickness
TM

Kaowool M Board

.47

2.13

1.5" (1-1/2")

Micore 160™

.35

2.86

1.12" (1-1/8")

Micore 300™

.46

2.17

1.47" (1-1/2")

Durock™ Cement Board

1.92

.52

6.13" (6-1/8")

Hardibacker™

1.95

.51

6.22" (6-1/4")

Hardibacker 500™

2.30

.43

7.34" (7-3/8")

Cultured Stone Hearthstone™

2.82

.35

9" (9")

Wonderboard

3.23

.31

10.3" (10-3/8")

Super Firetemp M

.61

1.64

1.95" (2")

Super Firetemp L

.54

1.85

1.72" (1-3/4")

Face brick

9.00

.111

28.72" (28-3/4")

Common brick

5.00

.20

15.96” (16")

U.S. Gypsum

Johns-Manville

Note: An asterisk "*" indicates, it is a value taken from Table 2.
Using the k formula:

Specified min.
thickness
of listed
material

Answer - The minimum required thickness of the Micore 160 is 1.117”
therefore round up to nearest total standard thickness - Example: Use
two 5/8” (.625”) boards for a total thickness of 1-1/4” (1.250”).

U.S. Gypsum

kL = k value per inch of listed material
rL = r value per inch of listed material
TL = minimum thickness of listed material

TM (inches) =

U.S. Gypsum

Example: If Micore 160 Mineral Fiber Board is to be used for the
floor protection, how thick must this material be?

r-value (per Inch)
of listed material
x
r-value (per inch)
of alternate material

Johns-Manville

Cement mortar

5.00

.20

15.96” (16”)

Ceramic tile

12.5

.08

39.89" (39-7/8")

Marble

~11

~.09

35.12" (35-1/8")

Table 2 - USA AND CANADA REQUIREMENTS - GV300
** If the hearth extension material(s) that is intended to be used is NOT
listed on Table 2, the material can still be used if the material(s) is noncombustible. However, the manufacturer of the material must provide
either the listed k-value per inch or r-value per inch with listed thickness
so that the minimum thickness required for the hearth can be calculated
(per instructions here or as specified in the NFI Certification Manuals).
NOTE: Also see NFI (National Fireplace Institute) Certification Manuals
showing other acceptable calculation methods and acceptable alternate
materials which can be used.

10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Description

Ship.
Wt.

Ship.
Volume

H8338

Grandview 230
Wood-Burning
Stove

385 lb.

20.09 cu. ft.

Grandview 300
Wood-Burning
Stove

445 lb.

Stove Pipe Diameter
Single Wall or
Double Wall
6” (152 mm)

Log Length

16” W x 18” D Max.
(406mm W x 457mm D Max.)

Log Length

Firebox

17” W x 19” D x 12-1/2” H Max. Firebox
(432mm W x 483mm D x 318mm
H Max.) Volume = 2.3 cu. ft.

20.09 cu. ft.

NOTES:
• . Dimensions shown are approximations only
.25(+/- 1/4”)
• Diagrams, illustrations and photographs are
not to scale - consult installation instructions.
Product designs, materials, dimensions, specifications, colors and prices are subject to change or
discontinuance without notice.
• Approved for residential, manufactured home
(GV230 only), and alcove installations.
• Optional Kits Available:
Door Trim Kit
Blower
Outside Air Kit
Louvers
Legs (choice of three styles)
Pedestal
Ash Drawer for legs or for pedestal

Glass Viewing Area

16-1/2” W x 11-5/16” H
(419mm W x 287mm H)

EPA Test Load:
Cord Wood: u

28,200 BTUs/hr.
76,000 BTUs/hr.

Maximum Burn Times u

12 hours

Heating Capacity u

1200 to 2200 sq. ft.

EPA Grams Per Hour

3.6 gr/hr

17” W x 21” D Max.
(341.8mm W x 533mm D Max.)
18.2” W x 21.23” D x 13” H Max.
(462.28mm W x 539.25mm D x
330.2mm H Max.)
Volume = 2.91 cu. ft.

Glass Viewing Area

16-1/2” W x 11-5/16” H
(419mm W x 287mm H)

EPA Test Load:
Cord Wood: u

29,181 BTUs/hr.
100,000 BTUs/hr.

Maximum Burn Times u 14 hours

EPA Phase II and Washington State Approved

Heating Capacity u

2000 to 3000 sq. ft.

EPA Grams Per Hour

3.09 gr/hr

EPA Phase II and Washington State Approved
A

6”
(152mm)

Operation

H8958

Stove Pipe Diameter
Single Wall or
Double Wall
6” (152 mm)

Planning Installation Safety and General

Cat.
No.

GV300 Specifications

Installation

Product Reference Information

GV230 Specifications

uSquare-foot heating capacities and burn times
are approximations only. Actual performance
may vary depending upon home design and
insulation, ceiling heights, climate, condition and
type of wood used, appliance location, burn rate,
accessories chosen, chimney installation and how
the appliance is operated.

The Grandview™ Models GV230 and GV300
woodstoves are safety listed with the following
agency:

H
Pedestal - J
Olympic Legs - K
Coastal Legs - L
Lakeview Legs - M

Maintenance

SPECIFICATIONS - GV230 AND GV300

• Intertek, Tested to UL 1482, ULC S627

4002589

Model

GV230

25-1/8”
(638mm)

24-3/4”
(629mm)

26-5/8”
(676mm)

6-9/16”
(167mm)

23-3/4”
(603mm)

21-5/16”
(541mm)

1”
(25mm)

GV300

26-1/2”
(673mm)

27-3/8”
(695mm)

29-5/16”
(744mm)

6-5/8”
(169mm)

26-3/16”
(666mm)

21-7/16”
(544mm)

1-1/16”
(27mm)

Model

GV230

11-5/16”
(287mm)

16-1/2”
(419mm)

35”
(889mm)

33-1/2”
(851mm)

32-1/2”
(826mm)

32-13/16”
(833mm)

23-1/8”
(587mm)

GV300

16-1/2”
(419mm)

11-5/16”
(287mm)

36-1/8
(917mm)

34-5/8
(880mm)

33-5/8
(854mm)

33-15/16”
(862mm)

23-1/8
(588mm)

Figure 8 - Dimensions
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Parts / Accessories

Troubleshooting

Using 6” Diameter Single Wall Connector Pipe

Single Wall Pipe

STAINLESS STEEL LINER
Using 6” Diameter Rigid Stainless Steel Liner

INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!

INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Chimney
Termination
Rain Cap

Chimney
Termination
Cap
Storm
Collar
Roof
Flashing

Flashing

Ceiling Support
Assembly

Length
Masonry
Adaptor

Slip
Adaptor

Single wall stove pipe
must not pass through
attics, closets, walls or
ceilings. It is used to
connect this appliance
to a factory built or
masonry chimney.
Fasten each stove pipe
connection with at least
3 sheet metal screws.

90° Tee

Chimney
Connector

6” x 24” 24-gage
black steel or 26
gage blued steel
single wall pipe
Fasten stove pipe to
flue collar with 3 sheet
metal screws.

Floor
Protector

Figure 10 - Connected to a Masonry Chimney
Floor
Protector

YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.

Figure 9 - Typical Installation

12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Double Wall Pipe

Using 6” Diameter Type L-Vent Connector Pipe
Mobile (Manufactured) Home Installation Shown

INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Mobile home installations
require a spark arrestor at the
chimney termination.
Termination Cap
with Spark Arrestor

3 Feet (0.9M)
Minimum

Remove, if mobile
home is transported

Storm
Collar
Flashing

Fasten each stove pipe
connection with at least
3 sheet metal screws.

Support
Box

Planning Installation Safety and General

• Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
• All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot. The
connector pipe must meet minimum clearances in any direction to
walls or other combustible materials. It must attach to a listed double
wall metal chimney at least 6” in diameter or to a masonry chimney
with a flue passage of at least 48 square inches.
• It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use. Install connector at
no less than the minimum clearances from the ceiling when using a
90-degree elbow to pass through combustible constructions.
• Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufacturer’s
directions. NFPA No. 211 gives approved methods for passing a flue
pipe through combustible constructions (see Page 14).

Installation

CHIMNEY INSTALLATION

All mobile home
installations require
an outside air kit (see
Page 31 for ordering
information) and
the stove must be
secured to the floor
and grounded to the
mobile home chassis.

Minimum of
12-15’ (3.7-4.6M)
of Flue to achieve
a stable draft.

Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (in
Canada CAN/CSA Z240 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
A225.1.

DVL Close
Clearance
Connector Pipe

Maintenance

Model GV230 woodstove is approved for installation into a manufactured (mobile) home. NOTE: Model GV300 woodstove is not
approved for installation into a manufactured (mobile) home.

Fasten stove pipe to
flue collar using 3
sheet metal screws.

All mobile home installations require an outside air kit (see Page 31 for
ordering information). The stove must be secured to the floor and grounded
to the chassis of the mobile home (see Page 13 for detailed instructions).

Operation

Manufactured Home Installations (GV230 ONLY)
(ref. Figure 11)

Approved Chimney* - Your stove is approved for use with Class A, UL
103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type and Building
Heating Appliance Chimney (HT chimney - 2100° Fahrenheit) and double
wall connector pipe. Approved chimney brands are Security Chimneys™,
Jakes Evans/GSW, Dura-vent, Metal Fab, Ameri-Tec, Metalbestos and
Industrial Chimney (ICC).
Clearances to connector shall be measured from 6” flue collar. Restrictions
apply! Read instructions before installing.

Floor
Protector

Chassis

Install Outside Air
Kits per instructions
on Page 17

Figure 11 - Typical Installation

YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.

Secure to floor per
instructions on Page 16

Floor

Grounded to Steel Chassis
using a #8 AGW copper
wire or equivalent.

Parts / Accessories

CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

Troubleshooting

WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A MOBILE
HOME.

13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Chimney Connector Systems and Clearances from Combustible
Walls for Residential Heating Appliances (NFPA 211) Refer to
Figure 12.

System A

Minimum chimney clearance to brick
and combustibles 2 in. (51mm)

System A. Minimum 3.5 in. (90 mm) thick brick masonry wall
framed into combustible wall with a minimum of 12 in. (305 mm)
brick separation from clay liner to combustibles. Fireclay liner (ASTM
C 315, Standard Specification for Clay Flue Linings, or equivalent),
minimum 5/8 in. (16 mm) wall thickness, shall run from outer surface
of brick wall to, but not beyond, the inner surface of chimney flue
liner and shall be firmly cemented in place.

Minimum clearance
12 in. (305mm)
of brick

Chimney
flue
Minimum
12 in. (305mm)
to combustibles

Clearance: 12 in. (305 mm)
System B. Solid-insulated, listed factory-built chimney length of the
same inside diameter as the chimney connector and having 1 in.
(25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air
space between the outer wall of the chimney length and combustibles.

System B

The inner end of the chimney length shall be flush with the inside of
the masonry chimney flue and shall be sealed to the flue and to the
brick masonry penetration with non-water-soluble refractory cement.
Supports shall be securely fastened to wall surfaces on all sides.

Masonry chimney
constructed to NFPA 211

Air Space – 9 in.
(228.6mm) Min.

Supports shall be securely fastened to wall surfaces on all sides and
shall be sized to fit and hold chimney section. Fasteners used to secure
chimney section shall not penetrate chimney flue liner.

Chimney
Connector

Use Chimney
Mfrs. Parts to
Attach
Chimney
Connector
flue
Solid-Insulated
Masonry chimney
Listed Factoryconstructed to NFPA 211
Built Chimney
Sheet Steel Supports Length

System C

Minimum chimney clearance to sheet
steel supportrs and combustibles
2 in. (51mm)

Supports shall be securely fastened to wall surfaces on all sides and
shall be sized to fit and hold chimney section. Fasteners used to secure
chimney section shall not penetrate chimney flue liner.

System D. Solid-insulated, listed factory-built chimney length with
an inside diameter 2 in. (51 mm) larger than the chimney connector
and having 1 in. (25.4 mm) or more of insulation, serving as a passthrough for a single wall sheet steel chimney connector of minimum
24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in.
(51 mm) air space between the outer wall of chimney section and
combustibles. Minimum length of chimney section shall be 12 in.
(305 mm). Chimney section concentric with and spaced 1 in. (25.4
mm) away from connector by means of sheet steel support plates
on both ends of chimney section. Opening shall be covered, and
chimney section supported on both sides with sheet steel supports
of minimum 24 gauge [0.024 in. (0.61 mm)] thickness.

Min. Clearance
9 in. (229mm)

Nonsoluble
Refractory
Cement
Chimney Length
Flush with
Inside of Flue

Clearance: 9 in. (229 mm)

Clearance: 6 in. (152 mm)

Fire clay
liner

Minimum Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (51mm)

Factory Built
Chimney Length

Fasteners between supports and the chimney length shall not penetrate the chimney liner.

System C. Sheet steel chimney connector, minimum 24 gauge [0.024
in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24
gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4
mm) air channels, separated from combustibles by a minimum of 6
in. (152 mm) of glass fiber insulation. Opening shall be covered, and
thimble supported with a sheet steel support, minimum 24 gauge
[0.024 in. (0.61 mm)] in thickness.

Chimney
connector

2 Air Channels, Each 1
in. (25.4 mm)
Chimney
Connector

2 Ventilated Air
Channels, Each
1 in. (25.4 mm)
Construction of
Sheet Steel

Chimney
flue
Masonry chimney
constructed to NFPA 211
Sheet Steel Supports
Minimum chimney clearance to sheet steel
supports and combustibles 2 in. (51mm)

System D
Sheet Steel
Supports
Chimney
Section

Min. Clearance
2 in. (51 mm)
1 in. (25.4 mm)
air space to
chimney length

Chimney
Connector
Chimney connector
Air Space – 2 in.
(51mm) Min.

Clearance: 2 in. (51 mm)

Chimney length
Sheet Steel Supports
Masonry chimney
constructed to NFPA 211

Additional requirements:
1. Insulation material used as part of wall pass-through system shall be
of noncombustible material and shall have a thermal conductivity of
1.0 Btu-in./hr-ft2 - ºF (4.88 kg-cal/hr-m2 - ºC) or less.
2. All clearances and thicknesses are minimums; larger clearances and
thicknesses shall be permitted.
3. Any material used to close up an opening for the connector shall be of
noncombustible material.
4. A connector to a masonry chimney, except for System B, shall extend
in one continuous piece through the wall pass-through system and the
chimney wall to the inner face of the flue liner, but not beyond.

Figure 12 - Chimney Connector Systems and Clearances from Combustible Walls

14
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.

CAUTION: Wear gloves during installation in case of sharp
edges on the stove.

Leg Installation

Pedestal Installation

1. Carefully place stove on it’s back. Be careful not to scratch the stove,
use a piece of cardboard or carpet to protect the back of the stove.
2. Using a 9/16” wrench or socket remove the bolt in each of the four
corners along with the attached shipping brackets.
3. Remove legs from the packaging and using the bolts and washers
that come with the legs install each leg in each corner with one bolt
and one washer.
4. Before the legs are fully tightened down make sure that they are aligned
correctly to match the front and side planes of the stove.
5. The stove can now be set up on the legs making sure that all baffle
boards and bricks are set back in place. These items may have shifted
when the stove was placed on it’s back.
6. If it is necessary to level, secure, or ground your stove, use the holes
in the bottom of the leg for those applications. To level the stove use
leg leveling kit (P/N H8407) or leveling pads (P/N H7638). Level by
adjusting the bolt or leveling pad down on each leg that is not in full
contact with the hearth or surface below that the stove in located on.

1. Remove the heater from the carton, if packaged, upon receipt and
check for any damaged or missing parts.
2. Install the 10-24 screws included with the pedestal kit to the bottom
of the stove as seen in Figure 14. You will need a 5/32” allen wrench
to complete this.
3. Carefully place stove on it’s back. Be careful not to scratch the stove,
use a piece of cardboard or carpet to protect the back of the stove.
4. The pedestal will have key hole slots that line up with the screws that
were placed in the bottom of the stove. Carefully install pedestal on
the installed screws with the open end of the pedestal towards the
rear of the stove.
5. Assuring that the pedestal is placed correctly in slots then tighten all
six screws.
6. The stove can now be set up on the pedestal making sure that all
baffle boards and bricks are set back in place. These items may have
shifted when the stove was placed on it’s back.
7. When installing a pedestal on this stove you MUST plug the one leg
mounting bolt hole, located on the bottom of the stove in the front left
corner, with the bolt that was used to mount the shipping legs. FAILURE TO INSTALL THIS BOLT PROPERLY WILL RESULT IN REDUCED
CONTROL OF THE STOVE’S COMBUSTION SYSTEM!

Planning Installation Safety and General

(Tieing down and grounding are required only in mobile homes)

You MUST plug
this one leg
mounting bolt
hole. Read Step
7 above.

Figure 13

Figure 14

Parts / Accessories

Troubleshooting

Maintenance

(Tieing down and grounding are required only in mobile homes)

Installation
Installation

Residential and Mobile Homes

Operation

Pedestal Installation

Leg Installation

15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ATTACHING STOVE to manufactured home floor GV230 WOODSTOVE ONLY

Stove Back

Leg Tie Down Kits (Manufactured [mobile] Homes)
Order:
H7665 Leg Tie Down Kit, Coastal and Lakeview Legs
H5308 Leg Tie Down Kit, Olympic Legs

ATTACHING STOVE TO MANUFACTURED HOME FLOOR
THE STOVE MUST BE ATTACHED TO THE FLOOR AT NO LESS THAN
TWO POINTS

Tie Down Holes

Figure 15 - Securing Pedestal to Floor

Pedestal
Locate the two holes on the back of the pedestal (Figure 15). Secure the
pedestal to the floor using two field provided 1/4” screws.
Lakeview and Coastal Legs
Connect the bolt down bracket to each leg using kit (P/N H7665) screw
as shown in Figure 16. Secure the leg bracket to the floor using one field
provided 1/4” bolt.
Olympic Legs
Connect the bolt down bracket to each leg using kit (P/N H5308) screw
as shown in Figure 17. Secure the leg bracket to the floor using one field
provided 1/4” screw.
Figure 16 - Securing Coastal and Lakeview Legs to Floor

Figure 17 - Securing Olympic Legs to Floor

16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Outside Air Kits
Order:
1 ea. P/N UZIAD Outside Air Coupler Kit (connects outside air ducting, UZI, to
stove)
AND
1 ea. P/N UZI Outside Air Ducting Kit (includes 4” insulated flex x 10’ long)
Coupler (attached to
existing collar)

Aluminum
Tape

Duct

Outside Air Kit Coupler
Figure 19 - Outside Air Connection to Stove

Aluminum Tape

Opening
Facing
Down

Duct

Wall

Operation

Screw

Figure 20 - Through the Wall, Outside Air Termination

Manufactured Home Through the Floor Outside Air Kit Installation (refer to Figure 21) - Model GV230 wood stove only.

Aluminum
Tape

UZIAD Outside Air Coupler

Coupler (attached to
existing collar)
Duct

Figure 21 - Manufactured Home Installation

Maintenance

- Make a 4-1/4” (110 mm) hole in the outside wall of the house at the
chosen location. From outside, place the outside air register in the
hole (open side down) and fasten the register to the wall, with screws
as shown (see Figure 20).
- Install the coupler onto the existing collar on stove (see Figure 18).
- Attach the duct to the coupler on stove (see Figure 19). Using the
aluminium tape provided, wrap the tape around the joint between the
flexible duct and the air inlet.

Outside
Intake

Troubleshooting

The outside air assembly may be installed according to the following
requirements:
A) Duct length should be kept to a minimum.
B) The air intake register must not be installed more than ten (10) feet
(3050 mm) above the base of the stove.
C) The fresh air must come from outside the house. The air intake must
not draw air from the attic, from the basement or garage.
D) The air intake should be installed where it is not likely to be blocked by
snow or exposed to extreme wind and away from automobile exhaust
fumes, gas meters and other vents.
E) The duct and register may be installed above or below floor level.

Figure 18

OUTDOORS

INDOORS

Through the Wall Outside Air Kit Installation
(refer to Figures 18, 19 and 20)

Parts / Accessories

To install the outside air kit coupler onto the stove, line up the “V” notch
in the coupler with the “V” notch in the open on the bottom of the stove.
Push and twist so the rolled edge catches the bottom of the stove and
continue turning full 360° to lock the coupler in place.

Installation

An outside air kit is required in Manufactured (mobile) Home installations. For residential installations, check with local authorities having
jurisdiction in your area, it may be mandatory.

Planning Installation Safety and General

Outside COMBUSTION Air Kit Installation - GV230 & GV300

17
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Grandview™ GV230

Brick and baffle Installation

CAUTION: Wear gloves during brick installation in case of
sharp edges inside the stove.

1. Install firebox bottom brick spacers on both the left and right side of
firebox. The brick spacers are located in the package with the manual.
Assure that brick spacers are pushed to each side until they are in
full contact with the firebox side on each side.
2. Install brick #1-20 in the numbered sequence shown in Figure 22.
3. Brick’s 13 and 14 will be located between the steel firebox and rear
baffle board (already installed).
4. Once all bricks are installed confirm that the already installed baffle
boards are in there correct location and resting on the secondary
burn tubes.

Warning: If the bricks are not installed exactly as
shown below, they could fall out of place during
refueling or burning of the stove causing serious
injury.

Letter A Brick Are Full Size

Firebox Brick Layout as
Viewed from the Front

13-A

9” (229mm) Long x
4-1/2” (114mm) Wide x
1-5/16” (33mm) Thick

14-A
18-A

15-A

19-A

16-A
17-A

9-A

10-A

11-A

1-A

2-A
4-A

3-A
6-A

5-A

20-A

12-A

8-A

7-A

Figure 22 - GV230 Brick Diagram

Back Baffle Board

Front Baffle Board
Back Baffle Board

Front Baffle Board

Figure 23 - GV230 Baffle Boards Installed

Figure 24 - GV230 Baffle Boards

18
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

6.5”
6.5
(165mm)

7.7
7.7”
(196mm)

Brick and baffle Installation

CAUTION: Wear gloves during brick installation in case of
sharp edges inside the stove.

1. Install brick #1-26 in the numbered sequence shown in Figure 25.

Warning: If the bricks are not installed exactly as
shown below, they could fall out of place during
refueling or burning of the stove causing serious
injury.

2. Once all bricks are installed confirm that the already installed baffle
boards are in there correct location and resting on the secondary
burn tubes.

Planning Installation Safety and General

Grandview™ GV300

5-A

7-A

6-A

9” (229mm) Long x
4-1/2” (114mm) Wide x
1-5/16” (33mm) Thick

13-A
16-A

10-A
2-A

4-A

3-A

20-A

19-A

14
A

15
A

22-A

21-A

17
A

Operation

12
A

11
A

9
A

8
A

1-A

18
A

24-A
26-A

23-A

Installation

Letter A Brick Are Full Size

Firebox Brick Layout as
Viewed from the Front

Maintenance

25-A

Figure 25 - GV300 Brick Diagram

Front and Back
Baffle Board

17.870”
17.870
(454mm)

Figure 26 - GV300 Baffle Boards Installed

Figure 27 - GV300 Baffle Boards

8.741
8.741”
(222mm)

Troubleshooting

Front Baffle Board

Parts / Accessories

Back Baffle Board

19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Post Installation Checks

FOR MOBILE HOME INSTALLS
Be sure the stove is properly grounded
Be sure the stove is properly securely
fastened to the floor
Be sure the outside air vent is free of
obstructions and has a mesh screen in place

Check that all chimney pipe joints are
secured and installed according to the
manufacturers instruction.
If used, make sure the outside air kit is
properly installed and unobstructed.
Make sure the legs or pedestal are securely
fastened to the stove.
Double check all stove clearances.
Be sure bricks and baffle boards are
properly installed.
If plated accessories are used, be sure
surfaces are clean prior to firing the stove.
See Page 21

FOR YOUR OWN PROTECTION AND INSURANCE PURPOSES,
HAVE YOUR CHIMNEY AND CONNECTOR PIPE INSTALLATION
INSPECTED BY YOUR LOCAL BUILDING CODE AUTHORITY OR
FIRE MARSHAL BEFORE STARTING A FIRE IN YOUR STOVE.
NOTIFY YOUR INSURANCE COMPANY.

20
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

LARGE ROARING FIRE UNTIL THIS CURING EFFECT IS COMPLETE
OR YOU MAY DAMAGE THE FINISH OF YOUR STOVE. Spray can

touch-ups should be done only with a high temperature stove paint (cat.
no. H8159), available from all Lennox Hearth Products dealers.

Burn-In Period

DOOR OPERATION
Do not operate the appliance with the door open or ajar other
than possibly during start up to create a draft (Do not leave the
unit unattended while the front door is slightly open during start
up). Operating the appliance with the door open other than in
initial start up if needed will produce extreme temperatures
within the appliance. Damage caused from over-firing is not
covered under the manufacturers limited warranty.

WARNING
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replacement parts.

Please be patient with the heat output of your stove or fireplace insert for
the first few weeks. The steel will go through a curing process that eliminates moisture, which is deep in the steel and firebrick. This moisture will
reduce initial heat output of your stove or fireplace insert and may make
it difficult to start. (DO NOT OVERFIRE THE STOVE DURING THIS

Door

PROCESS. IF THE STOVE OR CHIMNEY BECOMES RED, REDUCE
THE AMOUNT OF AIR ENTERING THE STOVE IMMEDIATELY).

Handle

Planning Installation Safety and General

Your new stove is painted with a high temperature paint that cures during
the first few firings. We recommend that you put your stove or fireplace
insert through a regimen of three burns. The first two should last for
20 minutes each at 250 degrees (the stove or fireplace insert should be
allowed to cool completely between each burn). The third should be a
burn of at least 450 degrees F. for 45-60 minutes. The paint will become
soft, gummy and emit non-toxic smoke during these burns. During these
first burns, open the appliance door frequently to help prevent the door
gasket from adhering to the appliance. After the stove or fireplace insert
cools down for the third time, the paint will harden. DO NOT BUILD A

5. Feeding excessive amounts of fuel to the stove or fireplace insert
should be avoided. It is important to supply it with sufficient draft
and fuel to maintain a moderately hot fire. If, during overnight burns,
heavy creosote deposits develop inside your stove and on the door,
the draft is set too low - review your burning habits!

Installation

If your stove has plated accessories, be sure to clean it with a household
type glass cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire and before any fire if the plated surfaces
have been handled or soiled. Do not close the door tightly during the
“Burn-In Period.” Also, open the door frequently (every 5-10 minutes)
to keep the gasket from adhering to the curing paint. Ventilate the
house well during these first firings as the paint gives off carbon dioxide
and unpleasant odors. It is recommended that persons sensitive to an
imbalance in the indoor air quality avoid the stove or fireplace insert
during the curing process.

Operation
Operation

FORE OPENING THE DOOR TO AVOID POSSIBLE COMBUSTION
FLASH!! (Ignition of hot volatile gases as the door is opened).

Maintenance

4. CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN BE-

Paint Curing

Opening Door - Lift
handle and pull to
open door
Closing Door - Hold
handle lifted, swing door
closed then push handle
down to engage latch

Figure 28

Parts / Accessories

1. Burn only dry, well-seasoned cord wood. In some states it is illegal
to burn wet wood or anything other than clean, dry wood products.
2. Your stove or fireplace insert is designed to operate with the door
closed! Operate only with the door shut tightly at all times except when
loading wood and possibly on start up to establish a draft. Never leave
the unit unattended while the front door is opened.
3. DO NOT contact or move the baffle boards while loading wood. Occasionally check the baffle to assure that the boards are in there correct
location.

Troubleshooting

Operating Hints

21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

DO NOT LEAVE THE STOVE UNATTENDED WHILE THE FRONT
DOOR IS SLIGHTLY OPEN.

Starting and Maintaining a Fire
1. NEVER USE FLAMMABLE LIQUIDS TO START OR REKINDLE

A SOLID FUEL FIRE!!

2. Fully open the primary draft control by placing draft control (wood
handle located on left side of the stove) in the highest position. This
control determines the amount of air entering the stove. Lowering
this control reduces the burn rate of the stove. For your convenience,
the control is marked with five positions to assist you in obtaining
repeatable burn rates.
3. Place a small amount of crumpled paper in the front of the firebox
and cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling to become
fully engulfed in flames. You will now close the wood units front door.
Your wood units front door may or may not need to be left slightly
open during this start up process, this depends on the stove model
and the amount of draft present.
5. When operating any wood burning appliance, it is important to
become familiar with how the damper control affects heat output
and the overall temperature of the appliance. A stove thermometer can be a helpful tool to help ensure you are not over-firing
your appliance and it will also ensure you are burning fuel at a
rate that is most efficient. Place a stove thermometer on the top
of the appliance as shown in Figure 29. Monitor the temperature every 15 minutes or so until you become more familiar with
your appliance. Close the damper all the way down if you begin
to reach 500 degrees, as this is a sign that you are operating
your appliance at too high a temperature.

Magnetic Thermometer
(recommended)

High Burn

CAUTION: Do Not alter the adjustment range of the draft control
for increased firing for any reason.
Operate only with fuel door and ash drawer closed. Maintain
all seals in good condition. Do not operate with broken glass.

Place a small
amount of
crumpled paper
in the front of the
firebox

Cover paper with
a few pieces of
kindling

Figure 30

Light paper

SEE MAINTENANCE SECTION FOR GLASS CLEANING GUIDELINES AND
TIPS FOR KEEPING THE GLASS CLEAN (PAGE 27).
6. Once kindling is burning well, larger pieces of wood may be added,
then the door should be fully closed if there was the need to keep it
slightly open during start up.
7. For best results, use smaller pieces of wood to get the stove or
fireplace insert temperature very high before loading larger wood
for sustained burns. If necessary, crack the door to allow ignition of
the fuel charge. Now you can add larger pieces of wood and after
several minutes of high burn, set the left control for the desired heat
output. Check the exhaust in about 15 to 20 minutes (see Figure 32).
Large amounts of smoke indicate an improper burn setting (either
too high or too low). Adjust and recheck in 5 to 10 minutes.

Medium Burn
Low Burn

Figure 29

Figure 31

22
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

What does “Well-Seasoned” mean?
When a tree is cut down, the wood is green, full of sap and moisture.
This moisture content can exceed 80%, which must be reduced to less
than 20%. Wood properly seasoned is then capable of generating the
heat the stove was designed to provide.
Green wood does not burn easily. Attempting to burn green wood often
results in a lot of smoke and very little fire. Time is the most important
factor in seasoning wood. Ideally the moisture content should be reduced
to 11-20%. NOTE: The use of a firewood moisture meter is recommended
to ensure the firewood contains less than 20% moisture.

Figure 32

Seasoning Guide
Softwoods - 6 months to 18 months
Hardwoods - 12 months to 24 months

Fuel
This appliance is designed and engineered to burn, dry, well-seasoned
wood only.
Dry, seasoned wood is that which has been cut, split and allowed to dry
under a covered area where air is free to flow and circulate under and
around the wood (not under a tarp or plastic). Make sure wood is not
stacked directly on the ground, it may absorb moisture from the ground.
It should be allowed to dry in these conditions for a minimum of six
months, preferably one year or more. IT MUST BE UNDERSTOOD

Logs that are 5” diameter across or larger should be split in half, three
pieces if over 8 inches, and four pieces when over a foot across. If a tree
has been dead for 2 - 4 years it still needs to be cut, split, and seasoned
for 6 to 24 months depending on the wood.

THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP
AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED.

Your stove will not operate at the level that it is meant to unless you use
seasoned, dry wood. Do not burn driftwood or wood that has been in salt
water, doing so will void your warranty. Do not burn incorrect fuels such
as flammable liquids, grease, treated wood, coal, garbage, cardboard,
solvents, or colored paper. Burning treated wood, garbage, solvents,
or colored paper may result in the release of toxic fumes. This type of
burning will also void your warranty.
Do Not store fuel within space heater installation clearances or within
the space required for refueling and ash removal.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Planning Installation Safety and General
Installation

Figure 33

Operation
Operation

4 Ft. (1.2M)
4'

Maintenance

4 Ft.
4'
(1.2M)

Troubleshooting

Standard
Cord of
Wood

Parts / Accessories

8 Ft.
8'
(2.4M)

Achieving Clean, Long Burns

Getting the Most Out of Your Stove
Recent developments in wood-burning technology have made woodburning a cleaner and more convenient way to heat your home. Overall
efficiency in a wood-burning appliance is a combination of combustion
efficiency and heat transfer efficiency. Whether heating your entire home or
just a room or two, your understanding of how to best operate your stove
or insert will enhance its overall efficiency and performance. What this
can mean to you is longer, cleaner burns, less wood use and more heat.

To achieve long burn times, after having thoroughly preheated the
stove, load the firebox without blocking the small air opening found in
the center front of the firebox. At this point, you may need to burn the
stove with the draft open for a few minutes to ignite the wood. All Lennox
Hearth Products stoves are EPA tested for emissions at low burn with the
air control completely closed. Whether or not you should burn your stove
with the air control completely closed will depend on the following factors:

The following sections will outline techniques you can use to “get the
most out of your stove.” Please read them carefully.

•
•
•
•
•

Maximizing Your Stove’s Overall Efficiency
It is important to know that for clean highly efficient burns you will
need to have sufficient temperatures inside the firebox for thorough
combustion. The best method for determining if you have sufficient
temperatures is to watch the brick lining in your firebox. When you first
light your stove or fireplace insert, the firebrick will turn a dark brown or
black. After 20 to 30 minutes of a hot fire, most of the bricks should return
to near their original beige color. This means the firebrick have reached
a high enough temperature for your stove to achieve high combustion
efficiency and you are ready to adjust the draft control to a lower setting.
Second and just as important, is achieving a high level of heat transfer
efficiency. Slowing the rate of flow through the stove or insert enhances
heat transfer, thus allowing more time for heat to be transferred into your
home. To do this, be sure to thoroughly preheat your stove and then
reduce the amount of primary air by closing the draft control down to a
lower setting. (More air may produce a slightly greater amount of heat,
but will greatly increase wood consumption).
To get the most out of your appliance, you will need to combine good
combustion efficiency with good heat transfer practices. The following
are some tips on how to operate your stove to achieve the highest overall
efficiency.
1. Thoroughly preheat your stove before slowing the burn rate by closing
the draft control.
2. When loading wood into a preheated stove or fireplace insert, allow
a vigorous fire to build before lowering the draft control.
3. Operate your stove as much as possible in the low to medium burn
ranges.
4. Do not lower the draft setting so low as to completely extinguish the
flames in the firebox. Check for at least some small flames twenty
minutes after setting the draft control.
5. Do not continually operate your stove or fireplace insert in the high
(wide open) setting. This wastes wood by carrying a great deal of
heat up the chimney and can damage your stove or fireplace insert
and chimney.
6. Go outside and check your chimney. More than a very small amount
of smoke indicates wasted heat, creosote build up and pollution (see
Figure 32).

How you load your wood
Your chimney type, height and draft
Your wood type and its moisture content
The temperature of the stove or fireplace insert
Which model stove or insert you have

In order to maximize the burn time of your stove you may need to experiment to get the right balance of starting temperature, wood type, and
draft control setting for your particular venting configuration. Do not
reload the stove for long burns when the stainless secondary tubes or
baffles are glowing red, or when the stove is uncomfortably hot to load.
This indicates the stove is too hot to load for a long burn.

MANUAL OPERATION: Flip blower mode switch to the
manual position (up) and adjust blower speed dial to desired setting.
To turn blower off, rotate blower speed dial counter clockwise until it
clicks “off.”

Manual / Auto
Rocker Switch

Blower Speed
Control Knob

AUTO OPERATION: Flip blower mode switch to auto position and turn blower speed dial clockwise until it clicks out of the “off”
position. When the stove warms up (approx. 15-20 Mins), the blower
will automatically turn on (adjust blower speed dial to desired speed
setting). When the stove or insert cools down, the blower will automatically turn off.

Figure 35 - Blower Controls

WARNING
The blower must be plugged directly into a properly
grounded three-prong receptacle, 120 VAC, 60 Hz, single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.

Blower Operation Guidelines
While in auto operation mode, the blower will turn off and on based on
The temperature of the stove or fireplace insert. Auto operation ensures
there is sufficient heat build-up to warm the air being moved by the blower before the blower is turned on. Likewise, when the stove cools off, the
blower is turned off to prevent circulating cool air. Depending on the size
and intensity of the fire it may be necessary to adjust the fan speed accordingly to ensure uninterrupted fan operation. For example a small fire
may require a slower fan speed to keep the heat output by the fan consistent. If the blower is operated in manual mode, it may be necessary to
adjust the blower speed as the fire begins to burn down and the stove is
no longer hot enough to effectively heat the air moved by the blower. If
the air coming from the blower feels cool, one should either decrease the
blower speed or stoke the fire to build up more heat.

Installation must be in accordance with National Electrical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA C22.1 Canadian Electrical Code - latest
edition.

N/C = NORMALLY CLOSED
N/O = NORMALLY OPEN

YLW

= FEMALE DISCONNECT
= MALE DISCONNECT
= STUD CONNECTION

RED
RED

WHT
BLK

BLK

POWER CORD
GRN
SPEED
CONTROL/OFF

Figure 34 - Blower Wiring Schematic

ROOM AIR
BLOWER

Troubleshooting

AUTO-RESET TEMPERATURE
SWITCH N/O

TWO POSITION
SWITCH
MANUAL/TEMPERATURE

Parts / Accessories

In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive
rear wall temperatures will result if the stove is burned
without the cover plate. The cover plate is not necessary
if a blower has never been installed because a knock-out
will be in place to act as the cover.

Maintenance

DANGER: Disconnect power before servicing blower.

NOTE: Turn blower off before opening the door to load the fuel.

NOTE: SWITCH CONDITIONS
GIVEN AT ROOM TEMPERATURE

Planning Installation Safety and General

The blower can be operated in either manual or automatic mode. When
operated automatically, the blower will turn on when the stove is hot,
and turn off when the stove is cool.

Installation

Blower Operation

Operation
Operation

BLOWER OPERATION (Optional Kit)

25
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Do’s and Don’ts
DO NOT: Install or operate the stove or fireplace insert before reading this manual.

DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT:

Open the stove or fireplace insert door without fully opening the draft first.

DO NOT:

Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in salt water
on the way to the mill. (This will void your warranty).

DO NOT:

Handle the Nickel Door Trim unnecessarily. Use the door handle only.

DO NOT:

Force oversized logs into the firebox as this may dislodge the baffle assembly.

DO NOT:

Close the door tightly during Burn-In Period.

DO:

Be sure to clean any fingerprints from optional accessories that have plated surfaces before burning the appliance. Clean the plated
surfaces only with household type glass cleaner and a very soft cloth.

DO:

Consult local building department if other than recommended clearances are desired.

DO:

Read instructions for the baffle boards occasionally to ensure you have not bumped or moved them out of place when loading wood.

DO:

Check the chimney and baffle monthly to make sure they are clean.

DO:

Burn seasoned, dry wood only! (RAIN = WET WOOD)

DO:

Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.

DO:

Enjoy the warm feeling of your new Country® Collection stove.

Maintenance
Glass Retainer

GLASS REPLACEMENT INSTRUCTIONS
(Refer to Figure 36)

Locate screws (10 ea.)
(peal back gasket as shown)

Arrows indicate
screw locations

Step 1. Remove Door Assembly - Remove the upper and lower hinge
pins by pressing the bottom of each hinge pin up, then pull out
from the top. Lift off door and place face down on a soft surface.
Step 2. Remove Glass Retainer Screws (10 ea.) - Using an 1/8” allen
wrench remove the ten glass retainer screws. To locate screws,
peel back the door gasket as necessary. The screws are located
by the holes in the stainless steel glass retainer strips.
Step 3. Remove Glass - Carefully remove broken glass one piece at a
time (protective leather gloves are recommended).
Step 4. Clean Door Frame - Clean the area of the door frame where the
new glass with gasket will be installed.

Upper
Hinge Pin
Door Gasket
Lower
Hinge Pin

Back View of Door

Glass Retainer
Back View of
Doorframe

Step 5. Install New Glass Assembly - Install the new glass with gasket
(use only factory supplied 5mm ceramic glass with gasket. Do
not substitute).
Step 6. Reinstall Retainer and Screws - Carefully reinstall the glass
retainer and screws. Be very careful not to overtighten the screws
(this could result in glass breakage when the stove is hot).
Step 7. Reinstall Door - Align hinges on door frame with corresponding
hinge holes on the face of stove. Reinstall the upper and lower
hinge pins from the top.

Glass with Gasket

Figure 36 - Glass Replacement
26
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Hex Head Screws
10 ea.

TIPS FOR KEEPING THE GLASS CLEAN
• Burn only dry seasoned cord wood. Wet wood = Dirty glass.
• A short, hot fire (15 - 20 minutes) may help to clean off some of the
normal buildup. Lower burns = more build-up. Higher burns = less
build-up.
• Keep freshly loaded wood away from the glass.
• After reloading, allow all the wood to catch flame before dampering
down the stove.

Creosote Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapors,
which combine with expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire.
The chimney and chimney connector should be inspected at least once
monthly during the heating season to determine if a creosote buildup has
occurred. If creosote has accumulated (1/8” [3 mm] or more), it should
be removed to reduce the risk of a chimney fire.
Establish a routine for the fuel, wood burner and firing technique.
Check daily for creosote build-up until experience shows how often
you need to clean to be safe. Be aware that the hotter the fire the
less creosote is deposited, and weekly cleaning may be necessary
in mild weather even though monthly cleaning may be enough in
the coldest months. Contact your local municipal or provincial fire
authority for information on how to handle a chimney fire. Have a
clearly understood plan to handle a chimney fire.

Locking Screw

Planning Installation Safety and General

Door Latch: Adjustment Instructions - Remove the right side heat
shield by loosening the 3 screws located on the back of the stove. Using
a “L” shaped 5/32” allen wrench, loosen the locking screw in the latch
assembly as shown in Figure 37. With the locking screw loosened, adjust
the top 5/32” allen screw (Figure 37) in the front of the stove to adjust
the door tension. Turning the screw to the right will tighten the door,
turning the screw to the left will loosen the door. When you loosen the
door it will be easiest to pull the roller pin to the full forward position and
make slight adjustments to tighten to the desired tension. Assure that
the tension on the front door creates a good seal between the gasket on
the front door and the firebox front. After adjusting the door tension,
re-tighten the lock screw and replace the heat shield.

•

Installation

Door Hinges: If door hinges need lubricating, use an anti-seize compound (never use oil) available from your Lennox Hearth Products dealer.

Do not use abrasives such as steel pads, steel wool or oven cleaner
as they will scratch the glass. Never scrape glass with a razor blade
as this may pit the glass and make it impossible to clean in the future.
Do not use chemical glass cleaners as they may damage the gaskets
or painted surfaces.

Operation
Operation

•

Maintenance

Door Gasket: Periodically check gasket to make sure it is not overcompressed. If compressed, replace with a special woven door rope.
(Don’t try substituting rope, only use Lennox Hearth Products door rope).
PLATED ACCESSORIES: Clean only with household type glass cleaner
and a very soft cotton cloth. Other products may damage plated finish,
paint and gaskets.
BAFFLE BOARDS: Your baffle boards should be inspected during every chimney cleaning. If either board is damaged then replace baffle
boards.
GLASS CLEANING GUIDELINES
WARNING: DO NOT CLEAN GLASS WHEN APPLIANCE IS HOT!
Glass on any wood stove will not stay perfectly clean. Here are some
guidelines for cleaning and caring for the glass:
• Ensure the stove is cold prior to cleaning glass.
• This appliance is designed to provide a flow of air over the inside of
the glass, where along with high heat helps inhibit build-up on the
glass. When build-up occurs, a commercial glass cleaner designed
for stoves is recommended. Regular household glass cleaners will
not clean creosote.

CAUTION
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasive cleaners. Do not clean with any materials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.

WARNING
Inspect and clean chimney and connector frequently.
Under certain conditions of use, creosote buildup
may occur rapidly.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Troubleshooting

Figure 37

Ashes should be scooped out of a cool stove or fireplace insert with a
small metal shovel. Ashes should be placed in a steel container with a
tight fitting lid and moved outdoors immediately. Other waste shall not
be placed in this container. The closed container of ashes should be
placed on a non-combustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes are disposed
of by burial in soil or otherwise locally dispersed, they should be retained
in the closed container until all the cinders have thoroughly cooled. Ashes
can ignite up to 72 hours after removal from the appliance.

Parts / Accessories

Adjustment Screw

Maintenance
Maintenance

DISPOSAL OF ASHES

Troubleshooting

Problem

Solution

POOR DRAFT:

Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have
poor drafts. Remember, the stove or fireplace inserts’ draft depends solely on the natural draft of the chimney (See
Draft Requirements on Page 4). If your stove or fireplace insert is not drafting properly, your chimney is the problem.
All stoves are thoroughly tested to ensure proper draft with the correct size chimney flue.

EXCESSIVE DRAFT:

With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by slowing the
burn rate of the stove or fireplace insert once it has reached proper operating temperature (See Maximizing Your Stoves
Overall Efficiency on Page 24).

DIRTY GLASS:

1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft control.
2) Make sure your wood is well-seasoned and dry (not open to rain - see Creosote [Page 27] and Fuel [Page 23] sections).
3) See Poor Draft section (above) and Cleaning Glass on Page 27.

SMOKES WHEN
DOOR IS OPEN:

1) If smoke is entering the room, check to make sure your baffle boards are properly installed.
2) Check the chimney for blockage due to creosote (see Chimney [Page 6] and Creosote [Page 27] sections).
3) Check draft (See POOR DRAFT section above).

WOOD BURNS
TOO FAST:

1) The draft control must be closed further.
2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”

POOR HEAT OUTPUT:

1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
2) Your stove or fireplace insert needs to be seasoned (moisture removed from the steel and brick). Continue to burn a
fire. It normally takes from one to three weeks of burning to season your stove (See Burn-In procedures on Page 21).
3) See Excessive Draft section above.

PAINT GIVES OFF
ODOR (smoke):

Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See Burn-In
Period on Page 21).

GV230

GV300

Inner Door Frame, Cast Iron

H8365

Outer Door Frame, Cast Iron

H8366

Glass Gasket 1”

H8380

Door Gasket 7/8”

Ceramic Glass With Gasket

Blower Snap Switch

H8374

Blower Blade

H8375

Blower Cover

H8376

Speed Control - High Temperature

H5742

Blower Rocker Switch

H8066

---

Blower Opening Cover Plate

H8399

Blower Power Cord

H5660

MISCELLANEOUS PARTS
---

Dry Graphite (apply to door handle
bushing)

71052

H5639

---

Anti Seize, 2 Gram Pouch

H5633

H8392

Heat Exchanger Bolt Kit

H8387

Flue Ring Bolt Kit

H8388

Door Handle Kit

H8395

---

Door Latch Assembly (4 button head screws
and latch)

H8397

---

Ash Drawer Hardware Kit

H8389

Glass, Retainer Kit

H8394

---

Taptite Qty 8 (34055)

H8390

Door Hardware Kit (includes 2 pins, door
roller and 10 button head screws and door
set screw)

H8398

---

Button Head Screw Qty 8 (34027)

H8391

---

Secondary Tube Retainer Clips

---

Replacement Secondary Air Tube Kit

H8373

H9081

Complete Firebrick Kit (GV230 - 20 bricks
included, GV300 - 26 bricks included)

H8378

H9082

LEG PARTS

FIREBOX PARTS

Coastal Brushed Nickel Leg - single leg

H8383

Coastal, Nickel Leg - single leg

H8384

Coastal, Black Leg - single leg

H8385

Firebrick 4-1/2” X 9”, Each

Lakeview, Steel Black Leg - single leg

H8386

Baffle Board Kit

---

Olympic, Brushed Nickel Cast Leg - single leg

H5619
Damper Rod

H8367

H5612
H8379

H9083

BODY PARTS

---

Olympic, Nickel Cast Leg - single leg

H5621

---

Olympic, Black Cast Leg - single leg

H5669

Damper Assembly

H8382

Stove Top Replacement

H8368

H9084

Cast Iron Heat Exchanger (hardware
included)

H8369

H9085

Left Side Heat Shield (hardware
included)

H8370

H9086

Right Side Heat Shield (hardware
included)

H8371

H9087

Rear, Heat, Shield (hardware included)

H8372

H9088

Heat Exchanger Gasket

---

Leg, Hardware, Bolt, Kit
PEDESTAL PARTS

Ash Plug Remover and Rake

H5564

Removable Ash Plug

H8381

Planning Installation Safety and General

Description

Operation

Item #

GV300

H8393
H8396

H8377

Maintenance

FRONT DOOR PARTS LIST

GV230

Troubleshooting
Troubleshooting

Contact an Lennox Hearth Products dealer to obtain any of these
parts. Never use substitute materials. Use of non-approved parts
can result in poor performance and safety hazards.

Description

Installation

BLOWER PARTS
Item #

Parts
Parts//Accessories
Accessories

Replacement Parts - ModelS Grandview™ 230 AND 300

27
15
32

24
28
14
7
8
3
1

5
9
6

30
11

36
31

21
18

19
13

30
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

DOOR TRIM
Item #

PEDESTAL (REQUIRED)
Description

PED-GV

GV230

Pedestal, Black

GV300

LEG-COSTL-BLK

LEG-COSTL-BRNKL

Coastal Legs, Black

H8339

Coastal Legs, Brushed Nickel

H8340

LEG-COSTL-NKL

Coastal Legs, Nickel

H8341

LEG-LKVIEW-BLK

Lakeview Legs, Black

H8342

LEG-OLY-B

Olympic Sculptured Black

70000

LEG-OLY-N

Olympic Sculptured Nickel

70002

LEG-OLY-BRN

Olympic Sculptured Brushed
Nickel

70008

ASHDR-KIT-PED-GV

Pedestal, Ash Drawer Kit

H8344

ASHDR-KIT-LEG-GV

Leg, Ash Drawer Kit

H8345

LOUVERS

LVR-GV230-BRNKL

Door Trim, Nickel

H8346

Door Trim, Brushed Nickel

H8347

BLOWER
BLWR-GV-700-SS

Blower

H8350

OUTSIDE AIR KITS
10

UZIAD

Outside Air Coupler for
Connection of UZI to
Fireplace

UZIAD

UZI

TSPK-B

Touch-up Spray Paint Kit,
Black

H8159

WP-LEGF-LBRKT

Leg Tie Down Kit, Coastal
& Lakeview Legs, Mobile
Homes

H7665

W-LEGF-LBRKT

Leg Tie Down Kit, Olympic
Legs, Mobile Homes

H5308

BELLA-LLK

Leg Leveling Pads

H7638

----

W-LLK

Leg Leveling Bolt Kit

H8407

Outside Air Kit (4’’ I.D. x
10 ft. long insulated flex)

UZI

Louvers, Black

H8348

H8959

Louvers, Brushed Nickel

H8349

H8960

Operation

LVP-GV230-BLK

GV300

COMMON ACCESSORIES

ASH DRAWERS

DRTRM-GV230-BRNKL

DRTRM-GV230-NKL

H8343

OR LEGS (REQUIRED)
2

GV230

Installation

Model

Description

PA I N T

Maintenance

Troubleshooting

Parts / Accessories

Item #

Model

Planning Installation Safety and General

Accessories - ModelS Grandview™ 230 AND 300

31
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Warranty
Your wood appliance is covered by a limited warranty (provided with the
appliance). Please read the warranty to be familiar with its coverage.
Retain this manual. File it with your other documents for future reference.

Replacement parts
See Page 29 for a complete replacement parts list. Use only parts supplied from the manufacturer.
Normally, all parts should be ordered through your Lennox Hearth
Products distributor or dealer. Parts will be shipped at prevailing prices
at time of order.

2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
visit us at www.LennoxHearthProducts.com
1-800-655-2008

Product reference information
We recommend that you record the following important information about
your appliance. If you did not purchase your appliance directly from a
Lennox Hearth Products dealer, then please call 1-800-655-2008 for the
name and phone number of your nearest Lennox Hearth Products dealer
who will answer your questions or address your concerns.

When ordering repair parts, always give the following information:
1. The model number of the appliance.

Your Appliance’s Model Number________________________________________
Your Appliance’s Serial Number_________________________________________
The Date On Which Your Appliance Was Installed___________________________
Your Dealer's Name__________________________________________________

Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, and prices, and also to discontinue colors, styles, and products.
Consult your local distributor for fireplace code information.
LENNOX®, the LENNOX design, DAVE LENNOX, the image of DAVE LENNOX and other related
LENNOX marks are registered or common law trademarks of Lennox Industries Inc. and are
used with permission.

P/N 506031-01 Rev. F 07/2013

P506031-01

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Create Date                     : 2013:07:19 08:51:37-07:00
Creator                         : Adobe InDesign CS5 (7.0.4)
Modify Date                     : 2013:07:22 08:57:15-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:76c4eced-f6ac-cb41-9ec7-daa284443b07
Document ID                     : xmp.did:936DEDCC89F0E2118C16D9FE32F49C62
Original Document ID            : adobe:docid:indd:fa59d9ea-104c-11df-b20b-f0fc12e1c386
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:46B139BA89F0E2118C16D9FE32F49C62
Derived From Document ID        : xmp.did:CDBCD4F4339DE211A565C5554CD2848E
Derived From Original Document ID: adobe:docid:indd:fa59d9ea-104c-11df-b20b-f0fc12e1c386
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:4021F219EE73DF119FBD9B3E2ACADB41, xmp.iid:4121F219EE73DF119FBD9B3E2ACADB41, xmp.iid:39ED60037884DF118F23B2E956C00FAB, xmp.iid:3AED60037884DF118F23B2E956C00FAB, xmp.iid:78220806BEA4DF119E20A9145DE662D6, xmp.iid:719FEC442EFEDF11BFADED784A70A9A0, xmp.iid:729FEC442EFEDF11BFADED784A70A9A0, xmp.iid:739FEC442EFEDF11BFADED784A70A9A0, xmp.iid:2A566D976201E01193F1CD9B79720B16, xmp.iid:2B566D976201E01193F1CD9B79720B16, xmp.iid:2C566D976201E01193F1CD9B79720B16, xmp.iid:2F566D976201E01193F1CD9B79720B16, xmp.iid:30566D976201E01193F1CD9B79720B16, xmp.iid:31566D976201E01193F1CD9B79720B16, xmp.iid:097C6A698801E01193F1CD9B79720B16, xmp.iid:90EB2FB01702E0118B15DAB58C12AD2C, xmp.iid:3DB7BCC97304E011B1E4A283878AA156, xmp.iid:E19F353CAB04E011B1E4A283878AA156, xmp.iid:B275A748F206E011B120E59E2521C08B, xmp.iid:261A637C6117E0119DDADEBE10AA5685, xmp.iid:B614D36E0A1DE011B7128DF2C7C8A799, xmp.iid:B714D36E0A1DE011B7128DF2C7C8A799, xmp.iid:B814D36E0A1DE011B7128DF2C7C8A799, xmp.iid:B914D36E0A1DE011B7128DF2C7C8A799, xmp.iid:65CD18B2121DE011B7128DF2C7C8A799, xmp.iid:66CD18B2121DE011B7128DF2C7C8A799, xmp.iid:67CD18B2121DE011B7128DF2C7C8A799, xmp.iid:0F83A3E02A1FE011B19AA1FF76E7EB3C, xmp.iid:244E2D72D732E01185F4F925C9B09224, xmp.iid:254E2D72D732E01185F4F925C9B09224, xmp.iid:264E2D72D732E01185F4F925C9B09224, xmp.iid:894472C7B933E01185F4F925C9B09224, xmp.iid:75FA6E1A1136E0119198A8449A12AF6F, xmp.iid:702E16CC2D44E01197D59E319004659C, xmp.iid:C10C8E15DE48E01197D59E319004659C, xmp.iid:BCC9853C9355E011835AB8C4CE6278AA, xmp.iid:BDC9853C9355E011835AB8C4CE6278AA, xmp.iid:C0C9853C9355E011835AB8C4CE6278AA, xmp.iid:B3759859BA80E011B916A9E1C57F5693, xmp.iid:834A48E85398E011A5F1E9A8FE786124, xmp.iid:6F5888A6FEA7E011857BE99541E1B542, xmp.iid:28F542E30DA8E011B995D817B32036DE, xmp.iid:29F542E30DA8E011B995D817B32036DE, xmp.iid:7A0CDCF1C7ACE01187BCEDEC5CDE26BF, xmp.iid:2D1A951413AFE011ACB9F621C1CCE90C, xmp.iid:9DC508E34AB1E0118B8CDB986B26D8B6, xmp.iid:8249AC475EB1E011824285E99E7A4B9D, xmp.iid:8349AC475EB1E011824285E99E7A4B9D, xmp.iid:8449AC475EB1E011824285E99E7A4B9D, xmp.iid:01D3639225B2E0118282A450EECAD4D0, xmp.iid:02D3639225B2E0118282A450EECAD4D0, xmp.iid:03D3639225B2E0118282A450EECAD4D0, xmp.iid:04D3639225B2E0118282A450EECAD4D0, xmp.iid:52E49F4ADBB2E011ADE6FF95E6C94D37, xmp.iid:56E49F4ADBB2E011ADE6FF95E6C94D37, xmp.iid:57E49F4ADBB2E011ADE6FF95E6C94D37, xmp.iid:5BE49F4ADBB2E011ADE6FF95E6C94D37, xmp.iid:B97790F2C7B3E011ADE6FF95E6C94D37, xmp.iid:BA7790F2C7B3E011ADE6FF95E6C94D37, xmp.iid:BB7790F2C7B3E011ADE6FF95E6C94D37, xmp.iid:B0FEDEC4DEB3E0118361E6F47DFB0698, xmp.iid:B2FEDEC4DEB3E0118361E6F47DFB0698, xmp.iid:B3FEDEC4DEB3E0118361E6F47DFB0698, xmp.iid:B5FEDEC4DEB3E0118361E6F47DFB0698, xmp.iid:CD309C4D85B4E0118361E6F47DFB0698, xmp.iid:3869297DADB7E0118008DAB674209A30, xmp.iid:3969297DADB7E0118008DAB674209A30, xmp.iid:7D175151BAB7E0118008DAB674209A30, xmp.iid:80175151BAB7E0118008DAB674209A30, xmp.iid:6644A09168B8E01196D5F9F6C176E2BE, xmp.iid:6744A09168B8E01196D5F9F6C176E2BE, xmp.iid:6844A09168B8E01196D5F9F6C176E2BE, xmp.iid:6D44A09168B8E01196D5F9F6C176E2BE, xmp.iid:6E44A09168B8E01196D5F9F6C176E2BE, xmp.iid:DF94F8475CBCE01196D5F9F6C176E2BE, xmp.iid:3D7AE365F7BDE0118922EF8EC5BF24EE, xmp.iid:3E7AE365F7BDE0118922EF8EC5BF24EE, xmp.iid:A91FA2A6EEC1E011810E9EF0CAF3045E, xmp.iid:AB1FA2A6EEC1E011810E9EF0CAF3045E, xmp.iid:AC1FA2A6EEC1E011810E9EF0CAF3045E, xmp.iid:DC1095B530C4E011835BDE54E03784CD, xmp.iid:DD1095B530C4E011835BDE54E03784CD, xmp.iid:DE1095B530C4E011835BDE54E03784CD, xmp.iid:DF1095B530C4E011835BDE54E03784CD, xmp.iid:821D4E7920C5E011928CCD317BA9438F, xmp.iid:73DE2A821FC8E011A6D28BF6980F05AE, xmp.iid:74DE2A821FC8E011A6D28BF6980F05AE, xmp.iid:FF4D1A9A3EC8E011A6D28BF6980F05AE, xmp.iid:004E1A9A3EC8E011A6D28BF6980F05AE, xmp.iid:6E730923E1C8E011A6D28BF6980F05AE, xmp.iid:6F730923E1C8E011A6D28BF6980F05AE, xmp.iid:7A48DF94C0C9E011A6D28BF6980F05AE, xmp.iid:5C98E184CEC9E0118FCDD5459D0BCF79, xmp.iid:5D98E184CEC9E0118FCDD5459D0BCF79, xmp.iid:5E98E184CEC9E0118FCDD5459D0BCF79, xmp.iid:5F98E184CEC9E0118FCDD5459D0BCF79, xmp.iid:1E287C820BCDE0119A50B3D8A6734F19, xmp.iid:F33F924D7DCEE0119A50B3D8A6734F19, xmp.iid:A4B421799FCEE011911EC7AFD54307CC, xmp.iid:9CE2C0DDA1CEE011911EC7AFD54307CC, xmp.iid:E8BD946B72D2E011AEE0BDF0DC4589C7, xmp.iid:5B3527B92AD3E011AEE0BDF0DC4589C7, xmp.iid:3D8B2AB853E8E011B2439D0D36C67708, xmp.iid:3E8B2AB853E8E011B2439D0D36C67708, xmp.iid:3F8B2AB853E8E011B2439D0D36C67708, xmp.iid:438B2AB853E8E011B2439D0D36C67708, xmp.iid:A4CC043363E8E011B2439D0D36C67708, xmp.iid:1A52E05617F1E011A988AE2952FEF4C0, xmp.iid:A52565E354FBE0118E1EE7421004D3A1, xmp.iid:A62565E354FBE0118E1EE7421004D3A1, xmp.iid:AB2565E354FBE0118E1EE7421004D3A1, xmp.iid:7F5572827A05E111ADC69BF2A7F02333, xmp.iid:6304053AFE0AE111AE23B20B18939D24, xmp.iid:4C4BE985E90BE111AE23B20B18939D24, xmp.iid:2841A33C810CE1119E6184EC0970DB43, xmp.iid:CDFBF1D28C0CE111977AEC7835059DCD, xmp.iid:57EBE01E4F36E111A8F7E2F1FD6AC33F, xmp.iid:6DF61FD3F636E111A8B7BA38356B3741, xmp.iid:6E4C1E9E0337E111B188CC378BF8CC82, xmp.iid:34249A742B37E111A3CD8C3DBAACBB40, xmp.iid:4F0A410FD837E111A3CD8C3DBAACBB40, xmp.iid:0D0BB13BA938E111A3CD8C3DBAACBB40, xmp.iid:5E1049DBDC3AE111A8DB9A8A43856431, xmp.iid:601049DBDC3AE111A8DB9A8A43856431, xmp.iid:5C5A5EBEA23BE111A8DB9A8A43856431, xmp.iid:D88A0DF9B03BE1118E3494E1B5F760CF, xmp.iid:C757B7E3793CE1119B89FF1E42ADC997, xmp.iid:5A7B8D4D2841E11196B8A6737CE146BA, xmp.iid:7D1B138E5E4CE111A26EA7FAC8C7EAA8, xmp.iid:7E1B138E5E4CE111A26EA7FAC8C7EAA8, xmp.iid:EBF9EC0DFC4CE111A26EA7FAC8C7EAA8, xmp.iid:743E4B82E450E111B7C5C20943505BF8, xmp.iid:753E4B82E450E111B7C5C20943505BF8, xmp.iid:7C3E4B82E450E111B7C5C20943505BF8, xmp.iid:4CF2A0EA0351E111B7C5C20943505BF8, xmp.iid:50F2A0EA0351E111B7C5C20943505BF8, xmp.iid:AB578A4EDB51E1118210B1C3B31DB5DE, xmp.iid:626953671054E111BBDDE3EB64A6EDE5, xmp.iid:16EEBF9B2F58E1119229A11572D4E8AB, xmp.iid:14AE7D736F77E111985FA1AC1D19864D, xmp.iid:E228D5DADD88E111AE6BD08EB32020B7, xmp.iid:085CC9C06689E11193E0A4C2F2B508BE, xmp.iid:170C1E7C2E8AE111932AA0E95F249780, xmp.iid:180C1E7C2E8AE111932AA0E95F249780, xmp.iid:40B13756628AE111932AA0E95F249780, xmp.iid:45B13756628AE111932AA0E95F249780, xmp.iid:7942B4BC138BE111B034BE63D06E33EE, xmp.iid:8B5240E4AB8FE111A49CD41E7C12FCC9, xmp.iid:BCEA68DCAE90E111A6A699AD8F16960C, xmp.iid:C1EA68DCAE90E111A6A699AD8F16960C, xmp.iid:3BE9816341AFE111B657F77688DED351, xmp.iid:3DE9816341AFE111B657F77688DED351, xmp.iid:D713975A14BBE111AB03B906DB6C8EEA, xmp.iid:D913975A14BBE111AB03B906DB6C8EEA, xmp.iid:507D445CD1BBE1118783CEBAAA9DA136, xmp.iid:A5705140DFBBE1118783CEBAAA9DA136, xmp.iid:1D6ED4AAEABEE1119D2ECBAFE0B2E10D, xmp.iid:1DC627AE6ADAE111B919A45829560769, xmp.iid:1EC627AE6ADAE111B919A45829560769, xmp.iid:9871B7FA29E7E1118C80995AD163DF21, xmp.iid:786FFE545406E211938CE59F0F37770F, xmp.iid:35A1AEE01E07E211B174C2F751294061, xmp.iid:E10F08557718E2119C46A03F23B4F08C, xmp.iid:EA0F08557718E2119C46A03F23B4F08C, xmp.iid:1FD353AC3519E211859B9AFE2A571F37, xmp.iid:23D353AC3519E211859B9AFE2A571F37, xmp.iid:DA51BBBAFE1DE211A5BFE80C28FD1C21, xmp.iid:DB51BBBAFE1DE211A5BFE80C28FD1C21, xmp.iid:E051BBBAFE1DE211A5BFE80C28FD1C21, xmp.iid:BD5EC95D161EE2118738F07116C9C82B, xmp.iid:CABCD4F4339DE211A565C5554CD2848E, xmp.iid:CBBCD4F4339DE211A565C5554CD2848E, xmp.iid:CCBCD4F4339DE211A565C5554CD2848E, xmp.iid:CDBCD4F4339DE211A565C5554CD2848E, xmp.iid:AD55DD153C9DE211A565C5554CD2848E, xmp.iid:A589EB563D9DE211A565C5554CD2848E, xmp.iid:2BE63CF16CA0E2119F0B90B8815DCEF5, xmp.iid:9CB84D8385A0E2118D36B2C803C9A31C, xmp.iid:DA6227D747A1E2118134C5B0CECB18AB, xmp.iid:18E6974FE9BBE211ACD9A56666C4D9CD, xmp.iid:CCE077ABEEBBE211ACD9A56666C4D9CD, xmp.iid:18C3179CCDC7E211919A871197247253, xmp.iid:F4531E48E8C7E211919A871197247253, xmp.iid:DFB0FB22E9C7E211919A871197247253, xmp.iid:D0FEE5C5E3D2E211B274DE9440EA4680, xmp.iid:6676810385D3E211BA8C9CA3A072EA40, xmp.iid:51BE54428DD3E211BA8C9CA3A072EA40, xmp.iid:1C1DF6B9A3D3E211BA8C9CA3A072EA40, xmp.iid:B2D24FF37AD4E211A63DAB44818910AB, xmp.iid:8810923150D8E211AB7DC797A7FA53A7, xmp.iid:D734E9B424D9E211AB7DC797A7FA53A7, xmp.iid:90AEC21625D9E211AB7DC797A7FA53A7, xmp.iid:1065473FD1D9E211AB7DC797A7FA53A7, xmp.iid:ABAE3B6FEBDCE211BC6B8D9ED0C9DF4C, xmp.iid:E821BE9166DFE211ADE9C525F62A3EC8, xmp.iid:0E99EA358AEDE211B894F55501D60941, xmp.iid:33DEF59528EEE211B894F55501D60941, xmp.iid:45B139BA89F0E2118C16D9FE32F49C62, xmp.iid:46B139BA89F0E2118C16D9FE32F49C62, xmp.iid:936DEDCC89F0E2118C16D9FE32F49C62, xmp.iid:946DEDCC89F0E2118C16D9FE32F49C62
History When                    : 2010:06:09 15:54:48-07:00, 2010:06:09 15:54:48-07:00, 2010:06:30 12:22:38-07:00, 2010:06:30 12:22:38-07:00, 2010:08:10 13:47:41-07:00, 2010:12:02 08:07:32-08:00, 2010:12:02 08:07:32-08:00, 2010:12:02 16:30:34-08:00, 2010:12:06 09:59:38-08:00, 2010:12:06 09:59:38-08:00, 2010:12:06 10:08:49-08:00, 2010:12:06 12:33:47-08:00, 2010:12:06 12:37:42-08:00, 2010:12:06 13:05:15-08:00, 2010:12:06 15:58:46-08:00, 2010:12:07 14:48:20-08:00, 2010:12:10 12:38:25-08:00, 2010:12:10 15:47:26-08:00, 2010:12:13 15:59:25-08:00, 2011:01:03 13:05:43-08:00, 2011:01:10 15:30:24-08:00, 2011:01:10 15:33:51-08:00, 2011:01:10 15:34:24-08:00, 2011:01:10 15:34:44-08:00, 2011:01:10 15:38:15-08:00, 2011:01:10 15:43:31-08:00, 2011:01:11 11:55:56-08:00, 2011:01:13 11:29:47-08:00, 2011:02:08 08:06:18-08:00, 2011:02:08 08:06:58-08:00, 2011:02:08 09:33:18-08:00, 2011:02:08 14:34:09-08:00, 2011:02:11 15:55:24-08:00, 2011:03:07 09:07:25-08:00, 2011:03:07 13:24:07-08:00, 2011:03:23 14:37:35-07:00, 2011:03:23 14:38:34-07:00, 2011:03:23 15:38:34-07:00, 2011:05:17 15:27:03-07:00, 2011:06:17 06:53:09-07:00, 2011:07:06 11:56:46-07:00, 2011:07:07 12:48:49-07:00, 2011:07:07 12:57:40-07:00, 2011:07:12 14:00:29-07:00, 2011:07:15 15:57:07-07:00, 2011:07:18 07:33:21-07:00, 2011:07:18 12:18:01-07:00, 2011:07:18 13:47:06-07:00, 2011:07:18 13:51:13-07:00, 2011:07:19 09:38:46-07:00, 2011:07:19 09:42:24-07:00, 2011:07:19 13:47:08-07:00, 2011:07:19 13:58:41-07:00, 2011:07:20 07:19:34-07:00, 2011:07:20 08:57:29-07:00, 2011:07:20 08:58:13-07:00, 2011:07:21 11:30:31-07:00, 2011:07:21 11:33:37-07:00, 2011:07:21 11:34:36-07:00, 2011:07:21 11:48:07-07:00, 2011:07:21 14:25:36-07:00, 2011:07:22 08:49:41-07:00, 2011:07:22 09:10:57-07:00, 2011:07:22 09:30:43-07:00, 2011:07:22 12:51:04-07:00, 2011:07:26 11:19:36-07:00, 2011:07:26 12:05:42-07:00, 2011:07:26 12:13:11-07:00, 2011:07:26 15:36:50-07:00, 2011:07:27 08:53:28-07:00, 2011:07:27 09:36:42-07:00, 2011:07:27 09:52:47-07:00, 2011:07:29 12:08:09-07:00, 2011:07:29 12:08:57-07:00, 2011:08:01 12:59:20-07:00, 2011:08:03 10:38:28-07:00, 2011:08:03 10:40:21-07:00, 2011:08:08 15:56:33-07:00, 2011:08:09 13:15:31-07:00, 2011:08:10 12:34:12-07:00, 2011:08:11 08:43:50-07:00, 2011:08:11 08:46:08-07:00, 2011:08:11 08:47:20-07:00, 2011:08:12 09:22:42-07:00, 2011:08:12 13:21:06-07:00, 2011:08:16 08:50:47-07:00, 2011:08:16 08:56:27-07:00, 2011:08:16 14:19-07:00, 2011:08:16 14:47:32-07:00, 2011:08:17 13:12:06-07:00, 2011:08:17 13:12:48-07:00, 2011:08:18 10:42:24-07:00, 2011:08:18 12:16:05-07:00, 2011:08:18 12:16:20-07:00, 2011:08:18 12:16:21-07:00, 2011:08:18 14:34:50-07:00, 2011:08:23 09:32:14-07:00, 2011:08:24 11:18:30-07:00, 2011:08:24 15:26:35-07:00, 2011:08:24 15:39:02-07:00, 2011:08:29 12:24:42-07:00, 2011:08:30 10:11:31-07:00, 2011:09:26 08:57:38-07:00, 2011:09:26 09:15:04-07:00, 2011:09:26 09:17:17-07:00, 2011:09:26 09:52:27-07:00, 2011:09:26 15:13:10-07:00, 2011:10:07 13:22:38-07:00, 2011:10:20 14:34:34-07:00, 2011:10:20 14:56:55-07:00, 2011:10:21 07:40:46-07:00, 2011:11:02 10:46:29-07:00, 2011:11:09 12:38:38-08:00, 2011:11:10 15:54:11-08:00, 2011:11:11 08:21:40-08:00, 2011:11:11 09:44:37-08:00, 2012:01:03 13:09:06-08:00, 2012:01:04 09:11:39-08:00, 2012:01:04 11:31:19-08:00, 2012:01:04 15:36:30-08:00, 2012:01:05 12:05:42-08:00, 2012:01:06 14:05:50-08:00, 2012:01:09 09:33:40-08:00, 2012:01:09 14:07:17-08:00, 2012:01:10 07:49:56-08:00, 2012:01:10 10:35:16-08:00, 2012:01:11 09:39:54-08:00, 2012:01:17 08:46:18-08:00, 2012:01:31 14:54:39-08:00, 2012:01:31 15:09:42-08:00, 2012:02:01 09:43:28-08:00, 2012:02:06 09:03:36-08:00, 2012:02:06 09:07:35-08:00, 2012:02:06 12:32:12-08:00, 2012:02:06 13:00:19-08:00, 2012:02:06 13:41:08-08:00, 2012:02:08 13:38:06-08:00, 2012:02:10 16:03:16-08:00, 2012:02:15 15:53:38-08:00, 2012:03:26 11:13:56-07:00, 2012:04:17 15:55:46-07:00, 2012:04:18 11:07:23-07:00, 2012:04:19 13:23:14-07:00, 2012:04:19 13:36:52-07:00, 2012:04:19 14:13-07:00, 2012:04:19 15:45-07:00, 2012:04:20 15:52:15-07:00, 2012:04:26 15:51:17-07:00, 2012:04:27 14:20:49-07:00, 2012:04:27 15:49:28-07:00, 2012:06:05 12:35:54-07:00, 2012:06:05 14:36:54-07:00, 2012:06:20 14:43:48-07:00, 2012:06:20 15:44:17-07:00, 2012:06:21 11:56:33-07:00, 2012:06:21 13:30:40-07:00, 2012:06:25 10:25:16-07:00, 2012:07:30 12:03:13-07:00, 2012:07:30 12:03:32-07:00, 2012:08:15 15:38:48-07:00, 2012:09:24 09:17:17-07:00, 2012:09:25 10:54:23-07:00, 2012:10:17 09:25:58-07:00, 2012:10:17 15:51:21-07:00, 2012:10:18 08:08:28-07:00, 2012:10:18 15:51:53-07:00, 2012:10:24 10:17:46-07:00, 2012:10:24 10:47:11-07:00, 2012:10:24 12:32:04-07:00, 2012:10:24 13:06:58-07:00, 2013:04:04 07:28:45-07:00, 2013:04:04 07:28:45-07:00, 2013:04:04 07:29:25-07:00, 2013:04:04 07:29:25-07:00, 2013:04:04 08:26:56-07:00, 2013:04:04 08:35:55-07:00, 2013:04:08 09:54:13-07:00, 2013:04:08 12:50:06-07:00, 2013:04:09 12:01:09-07:00, 2013:05:13 09:22:31-07:00, 2013:05:13 10:00:52-07:00, 2013:05:28 12:34:27-07:00, 2013:05:28 15:45:23-07:00, 2013:05:28 15:51:30-07:00, 2013:06:11 15:10:49-07:00, 2013:06:12 10:25:01-07:00, 2013:06:12 11:24:03-07:00, 2013:06:12 14:04:52-07:00, 2013:06:13 15:45:30-07:00, 2013:06:18 12:49:31-07:00, 2013:06:19 14:10:45-07:00, 2013:06:19 14:13:29-07:00, 2013:06:20 10:46:10-07:00, 2013:06:24 09:30:51-07:00, 2013:06:27 13:17:20-07:00, 2013:07:15 13:07:44-07:00, 2013:07:16 08:01:25-07:00, 2013:07:19 08:41:50-07:00, 2013:07:19 08:42:20-07:00, 2013:07:19 08:42:21-07:00, 2013:07:19 08:45:29-07:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /, /metadata, /metadata, /;/metadata, /, /metadata, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /;/metadata, /metadata, /metadata, /, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata
Metadata Date                   : 2013:07:22 08:57:15-05:00
Creator Tool                    : Adobe InDesign CS5 (7.0.4)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 10098 bytes, use -b option to extract), (Binary data 8115 bytes, use -b option to extract)
Doc Change Count                : 38119
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 32

EXIF Metadata provided by EXIF.tools

GRANDVIEW GV230 Manuel LENNOX 230

Navigation menu

Versions of this User Manual:

Views

Navigation