2016 Meridian 400SLD Bulk Seed Tender Operators Manual Operator
User Manual: Meridian-400SLD-Seed-Tender-Operator-Manual
Open the PDF directly: View PDF .
Page Count: 84
Download | ![]() |
Open PDF In Browser | View PDF |
PRODUCT WARRANTY REGISTRATION FORM WARRANTY REGISTRATION This form must be filled out by the dealer and signed by both the dealer and the customer at the time of delivery. Please mail or fax the completed form for validation of the equipment registration. Customer’s Name______________________________________________________ Address ______________________________________________________________ City, State, Postal Code____ _____________________, _______, ___________ Cut Here to Remove Page Phone Number (_______) _______- ___________ PRODUCT INFORMATION Seed Tender Model # ___________ S e r i a l N u m b e r # _______________________ I have thoroughly instructed the buyer on the above-described equipment, including review of the Operator’s Manual content, equipment care, adjustments, operational use, safety procedures, and applicable warranty policy. Dealer/Company Name____________________________________ City, State, Postal Code _________________________, ________________ , ______________ Dealer’s Signature___________________________________________ Date ____/____/______ The above equipment and Operator’s Manual have been received by me, and I have been thoroughly instructed as to care, adjustments, safe operation, and applicable warranty policy. Owner’s Signature_____________________________________ Date ____/____/_______ 2902 Expansion Blvd. Storm Lake, Iowa 50588 Phone: 800-437-2334 Fax: 712-732-1028 Email: iowa_warranty@meridianmfg.com 3 PRODUCT WARRANTY REGISTRATION FORM DEALER INSPECTION FORM DEALER INSPECTION REPORT Review safetycheck and operating instructions withlevel owner. ____If equipped, gasoline engine fuel Verify receipt of all options ordered. ____If equipped, check gasoline engine oil level Verify that towstart vehicle is large engine enough to safely tow seed tender. ____If equipped, gasoline Check gasoline engine fuel level. Addharness as needed. ____Inspect brake and lighting wiring connection ____Check air pressure in oil tires Check gasoline engine level. Add as needed. ____Make sure electric aresure in working condition Start gasoline enginebrakes and make it operates properly. ____Make all in guards/shields correctly Check sure oil level hydraulic tank. are Addinstalled as needed. ____Make all safety signsAdd are as installed Check sure air pressure in tires. needed.and ledgible ____Make surewheel all four 1993 Diesel Fuel Placards are installed Make sure nuts/bolts are tightened to proper torque on all wheels. ____Reflectors and lights must clean and working Make sure hitch-to-tongue andbe hitch-to-frame bolts are tightened to proper torque. ____Inspect customer’s hitch for 2 180 -5/16” ball and locks into towing position. Make sure conveyor tube rotates degrees ____Verify receipt of all options Make sure the weighing systemordered is working properly. ____Make sure hitch-to-tongue bolts are tight Make sure the remote control unit is working properly. ____Make sure safety chains are properly attached and are in good working condition Make sure all guards/shields are installed correctly. ____Wheel nuts/bolts must be tightened to proper torque on all wheels Make sure all safety signs are installed and legible. ____Wiring harness plug must be in working condition and fit into tow vehicle’s receptacle Reflectors and lights must be clean and working properly. ____Make sure breakaway cable and pin is supplied with trailer Inspect brake and lighting wiring harness connections. All lights must be functioning. ____Make sure battery is fully charged and in good working order Make sure seed tender battery is fully charged and in good working order. ____Make sure license plate light is operating Make sure breakaway brake system battery is fully charged and in good working order. ____Make sure turn signal lights are operating Make sure electric brakes are in working condition. ____Make sure brake lights are operating Inspect customer’s hitch for 2-5/16” ball or fifth wheel. ____Verify that tow vehicle is large enough to safely tow the trailer Make sure safety chains are properly attached and are in good working condition. ____Make sure owner is instructed to check wheel bolt/nut torque at Wiring harness plugmiles; must be in working condition and fit into tow vehicle’s receptacle. 5, 10, 25, and 50 then check annually ____Review safety and operating instructions with owner Make sure breakaway brake cable and pin is supplied with trailer. Make sure license plate light is operating. Make sure turn signal lights are operating. Make sure brake lights are operating. Make sure owner is instructed to check wheel bolt/nut torque at 5, 10, 25, and 50 miles; then check annually. 2902 E xpansion Blvd . S torm Lake , IA 50588 PH# 712 -732 -1780 FAX# 712 -732 -1028 Date: ____/____/_______ CERTIFICATE OF ORIGIN LICENSING INFORMATION SOLD TO : DEALER : ___________________________Business ___________________________Contact ___________________________Address ___________________________City, State, Zip ___________________________Business ___________________________Contact ___________________________Address ________________________ City, State, Zip TENDER MODEL #_________________________________________________________ TENDER WEIGHT__________________________________________________________ TENDER SERIAL #__________________________________________________________ (One serial number is issued on complete tender packages. Those trailers do not receive a serial number.) TRAILER MODEL #:_________________________________ Cut Here to Remove Page TRAILER SERIAL #________________________________________ Tender 110 BST Wagon TRAILER WEIGHT :_________________ 80110 1,004# 240 –Rear Facing (BH trailer included) 80121 3720# Tender 110 BST -T (trailer included) 80111 1,830# 240 –Fr ont Facing (BH trailer included) 80136 3720# Tender 22 5 R ST Wagon 80131 1733# Tender 375 (no trailer) 80349 4207# Ten der 22 5 RST -BH 80601 3375# Tender 375 -BH 80345 6071# Tender 225RST -GN 80602 4097 # Tender 375 -GN 80346 6721# Tender 225RST -BWT -BH 80603 3577# Tender 375 -BWT -BH 80347 6079# Tender 225RST -BWT -GN 80604 4299# Tender 375BWT -GN 80348 6729# 80249 2,545# Tender 375RT8 -BWT (trailer included) 80377 5,913# Tender 240RT6 -BWT -BH 802 53 4,475# Tender 375RT8 -T (trailer included) 80379 5,607# Tender 240RT6 -BH 802 50 4,174# Tender T itan 2SE -T (trailer included) 80201 2,254# 802 51 2,604# Tender Titan 2SE -BWT 80616 2302# Tender 240RT8 -BWT -BH 80248 4,534# Tender T itan 2-T (11 ’ 1 0” discharge) 80134 1820# Tender 240RT8 -GN 8025 5 4,232# Tender Titan 2 -T (15 ’ 6” discharge) 80135 1868# Tender 240RT6 Tender 240RT8 Tender 240 RT8 -BWT -GN 80243 4,491# 80401 2,803# Tender 375RT6 Wagon 80381 3,094# Tender T4SE -T (trailer included) Tender T4SE Wagon 80402 4,431# Tender 375RT6 -BH 80324 5,636# Ten der T4SE -BWT (trailer included) 80403 4,833# Tender 375RT6 -BWT -BH 80337 5,942# Tender T4SE -T -GN 80609 4893 # Tender 375RT6 -GN 80338 6637# Tender 4SE -T -GN -BWT 80608 5235 # Tender 375RT8 80382 3476# Tender 400 -6SLD 80352 3375 # Tender 37 5RT8 Wagon 80376 3106# Tender 400BH -6SLD 80353 5040 # Tender 37 5RT8 –BH 80326 5760# Tender 400GN -6SLD 80354 5690 # Tender 375RT8 -GN 80327 6441# Tender 400 -8SLD 80355 3530# Tender 375RT8 -BWT -BH 80339 5990# Tender400BH -8SLD 80356 5195# Tender 37 5RT8 -GN 80340 6672# Tender 400GN -8SLD 80357 5845 # 5 IMPORTANT INFORMATION SERIAL NUMBER LOCATION PATENT INFORMATION Report the serial number of your Meridian 400 SLD Seed Tender and engine when ordering parts or requesting service or other information. The serial number plates are located where indicated. Please mark the number in the space provided for easy reference. Seed Tender Meridian continuously enhances its product offering through product improvements and new product innovations. Marketplace feedback, technological innovation, new materials and manufacturing methods, and a philosophy of continuous improvement constantly challenge the company to develop new and better ways of addressing market needs. Meridian is committed to innovation and reinvestment and as a result, the company maintains a portfolio of patents and intellectual property. For more information on our patents please see our website: www.meridianmfg.com/patents Engine Model Number: 400 SLD Serial Number: ____________________________ Engine Serial Number: ______________________ 7 CONTENTS 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.1 Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2 Operator Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.3 Owner/Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2. SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.1 General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.2 Equipment Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3 Safety Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.4 Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.4.1 How to Install Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.5 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.6 Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.7 Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.8 Lock-Out or Tag-Out Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.9 Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.10 Transport Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.11 Refuelling Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.12 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.13 Sign-Off Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3. SAFETY SIGN LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.1 Overall Seed Tender Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.2 Bolt Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.2.1 Bolt Torque Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.2.2 Grade Markings Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5. MACHINE COMPONENTS AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.1 Component Nomenclature and Location . . . . . . . . . . . . . . . . . . . . . . . . 24 5.2 Engine and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.3 Control System Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.3.1 Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.3.2 Setting the Weight to Dispense . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.3.3 Setting Active Slide Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.3.4 Auto Reset Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.3.5 Control System Compliance Information . . . . . . . . . . . . . . . . . . . . . 27 5.4 Wireless Remote Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.4.1 Functions of Keypad Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.4.2 Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.4.3 Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6. PRE-OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.1 Machine Break-In Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.1.1 Before Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.1.2 Inspections for 1/2, 5, and 10 Hours . . . . . . . . . . . . . . . . . . . . . . . 31 6.2 Pre-Operation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7. 8 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1 Connecting the Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.1 Bumper Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.2 Gooseneck Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.2 Opening and Closing Roll‑Up Tarp . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.3.1 Conventional Loading (Filling the Seed Tender) . . . . . . . . . . . . . . . . . 36 7.3.2 Loading Using Self‑Filling Feature (Filling the Seed Tender) . . . . . . . . . . 37 7.3.2 Unloading (Filling the Planter) . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8. STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.2 Placing in Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.3 Removing from Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 9. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 9.1 Greasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 9.2 Grease Fitting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10. SERVICE PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.1 Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.1.1 Battery Replacement Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.1.2 Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.1.3 Remote Control Transmitter and Receiver Synchronization . . . . . . . . . . 48 10.1.4 Changing Sleep Time on the Transmitter . . . . . . . . . . . . . . . . . . . . 49 10.1.5 Weigh System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 10.2 Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 10.2.1 Hydraulic Oil Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 10.2.2 Hydraulic Pressure Relief Valves . . . . . . . . . . . . . . . . . . . . . . . . . 50 10.2.3 Hydraulic Motor Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 10.3 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 10.3.1 Approved Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 10.3.3 Change Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 10.3.4 Clean Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 10.5 Belt Delivery Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 10.5.1 Unplugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 10.5.2 Belt Tension Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 10.5.3 Belt Tracking Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 10.5.4 Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 10.6 Trailer Breakaway System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 10.6.1 Testing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 10.6.2 Changing Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 10.7 Wheel Bolt Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 10.8 Trailer Hitch Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 10.9 Service Record Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 10.9 Service Record Chart (Continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 10.10 Service Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.10.1 Daily (8 Hours) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.10.2 Weekly (50 Hours) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.10.3 Annually (400 Hours) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.11 Axle Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 10.11.1 First 200 Miles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 10.11.2 3,000 Miles or 3 Months . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 10.11.3 6,000 Miles or 6 Months . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 10.11.4 12,000 Miles or 12 Months . . . . . . . . . . . . . . . . . . . . . . . . . . 57 10.12 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 11. OEM LITERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 11.1 Honda® Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 11.2 Retractable Compartment Tarp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 11.3 Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 9 12. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 12.1 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 12.2 Control Panel Indicator LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 12.2.2 Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 12.2.1 Error Code Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 12.2.3 Control System Wiring Locations . . . . . . . . . . . . . . . . . . . . . . . . 61 13. WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 13.1 Warranty Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 14. PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 14.1 400 SLD Seed Tender 80137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 14.2 Conveyor (8”) 80634 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 14.2.1 Pan Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 14.2.2 Collection Chute Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 14.2.3 Tube Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 14.2.4 Discharge Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 14.3 Ladder, Slide Gate, View Port, and Sample Gate . . . . . . . . . . . . . . . . . . . 68 14.4 Axle/wheel Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 14.5 Hydraulic Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 14.5.1 Engine And Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . 71 14.5.2 Hydraulic Hoses And Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . 72 14.5.3 Hydraulic Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 14.6 Weigh System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 14.7 Decals and Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 14.8 Turret detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 14.9 Bumper Hitch Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 14.10 Gooseneck Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 10 1. 1.1 INTRODUCTION CONGRATULATIONS 1.2 OPERATOR ORIENTATION Congratulations on your choice of a Meridian Manufacturing Group 400 SLD Seed Tender Bulk Seed Tender to complement your seed delivery system in your farming operation. This equipment has been designed and manufactured to meet the exacting standards for such equipment in the agricultural industry and will keep your seed delivery system at optimum efficiency. MMG-00247 The Bulk Seed Tender system is designed to handle any kind of bulk seed, quickly transport it, and then transfer it into planters and drills, as required. This unit is designed to not only off-load bulk seed into the planting equipment, but it can also load itself from a bulk seed storage container or truck. Safe, efficient, and trouble‑free operation of your Bulk Seed Tender requires that you and anyone else who will be operating or maintaining the machine, read and understand the Safety, Operation, Maintenance, and Troubleshooting information contained within this Operator’s Manual. This manual covers the 400 SLD model manufactured by Meridian Manufacturing Group, Inc. Use the Table of Contents and Index as a guide to locate required information. The directions left, right, front and rear, as mentioned throughout this manual, are as seen from the truck drivers’ seat and facing in the direction of travel. 1.3 OWNER/OPERATOR It is the responsibility of the owner or operator to read this manual and to train all other operators before they start working with the machine. Follow all safety instructions exactly. Safety is everyone’s business. By following recommended procedures, a safe working environment is provided for the operator, bystanders, and the area around the work site. Untrained operators are not qualified and must not operate the machine. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. It is the responsibility of the owner or operator to read this manual and to train all operators before they start working with the machine. Follow all safety instructions as laid out in this manual. Keep this manual handy for easy reference and to pass on to new operators or owners. Call your Meridian Manufacturing Group, Inc. dealer if you need assistance, information, or additional copies of the manuals. The information, specifications, and illustrations in this manual are those in effect at the time of printing. We reserve the right to change specifications or design at any time without notice. MMG-00248 11 2. SAFETY SAFETY ALERT SYMBOL This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages on the Meridian Bulk Seed Tender Models and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message. WHY IS SAFETY IMPORTANT TO YOU? 3 Big Reasons • Accidents Disable and Kill • • Accidents Cost • • Accidents Can Be Avoided • SIGNAL WORDS: Note the use of the signal words DANGER, WARNING, and CAUTION with the safety messages. The appropriate signal word for each message has been selected using the following guidelines: CAUTION CAUTION - Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. WARNING WARNING - Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices. DANGER DANGER - Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations typically for machine components which, for functional purposes, cannot be guarded. If you have any questions not answered in this manual, require additional copies of the manual, or the manual is damaged, please contact your dealer or Meridian Manufacturing Group, 2902 Expansion Blvd., Storm Lake, Iowa, 50588, toll free 1-800-437-2334, phone (712) 732-1780, or fax (712) 732-1028. 12 YOU are responsible for the SAFE operation and maintenance of your Meridian Manufacturing Group bulk seed tender Model 400 SLD Seed Express delivery system. YOU must ensure that you and anyone else who is going to operate, maintain, or work around the Bulk Seed Tender be familiar with the operating and maintenance procedures and related SAFETY information contained in this manual. This manual will take you step-by-step through your working day and alert you to all good safety practices that should be adhered to while operating the Bulk Seed Tender system. Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVERYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follow all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. • • • 2.1 GENERAL SAFETY 1. Read and understand the Operator’s Manual and all safety signs before operating, maintaining, adjusting, filling, unloading, or unplugging the Bulk Seed Tender system. 2. Have a first aid kit available for use should the need arise and know how to use it. 3. Have a fire extinguisher available for use should the need arise and know how to use it. 4. Do not allow riders. 5. When working around or operating this equipment, wear appropriate personal protective equipment. This list includes but is not limited to: Bulk Seed Tender system owners must give operating instructions to operators or employees before allowing them to operate the machine, and then annually thereafter per OSHA (Occupational Safety and Health Administration) regulation 1928.57. The most important safety feature on this equipment is a SAFE operator. It is the operator’s responsibility to read and follow ALL Safety and Operating instructions in the manual. Most accidents can be avoided. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. Always be and stay alert to any possible unsafe operating or maintenance procedures or conditions. • A hard hat • Protective shoes with slip resistant soles • Protective goggles, glasses, or face shield • Heavy gloves and protective clothing • Respirator 6. Do not allow long hair, loose fitting clothing, or jewelry around equipment. 7. Install and secure all guards before starting. 8. STOP Stop engine, remove ignition key, and wait for all moving parts to stop before servicing, repairing, adjusting, loading, filling, or unplugging. 9. WARNING do not operate signed by date • • Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety of the components and systems and could affect the life of the equipment, possibly invalidating the warranty coverage. Establish a lock-out or tag-out policy for the work site. Be sure all personnel are trained in and follow all procedures. Lock-out or tag-out all power sources before working around loading/ unloading equipment. 10. Clear the area of people, especially small children, before starting. 11. Review safety related items annually with all personnel who will be operating, using, or maintaining the bulk seed tender system. Think SAFETY! Work SAFELY! 13 2.2 EQUIPMENT SAFETY GUIDELINES 1. Safety of the operator and bystanders is one of the main concerns in designing and developing a machine. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. You, the operator, can avoid many accidents by observing the following precautions in this section. To avoid personal injury or death, study the following precautions and insist those working with you, or for you, follow them. 2. In order to provide a better view, certain photographs or illustrations in this manual may show an assembly with a safety shield removed. However, equipment should never be operated in this condition. Keep all shields in place. If shield removal becomes necessary for repairs, replace the shield prior to use. 3. Never use alcoholic beverages or sedative drugs while operating this equipment. Consult your doctor about operating this machine while taking prescription medications. 4. Under no circumstances should young children be allowed to work with this equipment. Do not allow persons to operate or assemble this unit until they have read this manual and have developed a thorough understanding of the safety precautions and how it works. Review the safety instructions with all users annually. 5. This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a responsible, properly trained, and physically able person familiar with farm machinery and trained in this equipment’s operations. If the elderly are assisting with farm work, their physical limitations need to be recognized and accommodated. 6. Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is in question - DON’T TRY IT. 7. Do not modify the equipment in any way. Unauthorized modification may result in serious injury or death and may impair the function and life of the equipment. 14 8. In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer to Safety Messages and operation instruction in each of the appropriate sections of the auxiliary equipment and machine Manuals. Note all Safety Signs affixed to the auxiliary equipment. 2.3 SAFETY TRAINING 1. Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator or bystander. 2. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of this equipment. 3. The best safety feature is an informed, careful operator. It is the operator’s responsibility to read and comply with ALL Safety and Operating instructions in the manual. Accidents can be avoided. 4. Working with unfamiliar equipment can lead to injuries. Read this manual, as well as the manual for your auxiliary equipment, before assembling or operating to acquaint yourself with the machines. If this machine is used by any person other than yourself, it is your responsibility to make certain that the operator reads and understands the operator’s manuals and is instructed in safe and proper use. 5. Know your controls and how to immediately stop augers, conveyors, and any other auxiliary equipment in an emergency. Read this manual and the one provided with all auxiliary equipment. 6. Train all new personnel and review instructions frequently with employees. Be certain only a properly trained and physically able person will operate the machinery. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. 2.4 1. SAFETY SIGNS AR N I NG 2. PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS! Motors or equipment can be noisy enough to cause permanent or partial hearing loss. We recommend that you wear hearing protection on a full-time basis if the noise in the operator’s position exceeds 80db. NOTE: Hearing loss from loud noise (tractors, chain saws, radios, and other such sources close to the ear) is cumulative over a lifetime with uncertain natural recovery. 3. Clear working area of debris, trash, or hidden obstacles that might be hooked or snagged, causing injury, damage, or tripping. Keep safety signs clean and legible at all times. Replace any safety sign or instruction sign that is missing or not legible. Refer to the Safety Sign Location section for additional information. 2. When parts that displayed a safety sign are replaced, the replacement should also display the safety sign. 3. Replacement safety signs (labels) are available from your authorized Dealer Parts Department or the factory at no cost. 2.4.1 How to Install Safety Signs • Be sure that the installation area is clean and dry. • Be sure temperature is above 50°F (10°C). • Determine exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper. • Align the sign over the specified area and carefully press the small portion with the exposed sticky backing in place. • Slowly peel back the remaining paper and carefully smooth the remaining portion of the sign in place. • 2.5 1. 4. Operate only in daylight or good artificial light. 5. Be sure machine is properly attached to the trailer, adjusted, and in good operating condition. 6. Ensure that all guards, shielding, and safety signs are properly installed and in good condition. 7. Before starting, give the machine a “once over” for any loose bolts, worn parts, cracks, leaks, frayed belts, and make necessary repairs. Always follow maintenance instructions. 2.6 OPERATING SAFETY 1. Make sure that anyone who will be operating the bulk seed delivery system or working on or around the unit reads and understands all the operating, maintenance, and safety information in the operator’s manual. 2. Keep all bystanders, especially children, away from the machine when loading or unloading, or when authorized personnel are carrying out maintenance work. Small air pockets can be pierced with a pin and smoothed out using a piece of sign backing paper. PREPARATION Never operate the seed delivery system and auxiliary equipment until you have read and completely understand this manual, the auxiliary equipment Operator’s Manual, and each of the Safety Messages found on the safety signs on the delivery system and auxiliary equipment. 3. WARNING do not operate signed by date Establish a lock-out or tag-out policy for the work site. Be sure all personnel are trained in and follow all procedures. Lock-out or tag-out all power sources before servicing the unit or working around loading/ unloading equipment. 15 4. STOP 5. Stop engine, remove ignition key, and wait for all moving parts to stop before servicing, repairing, adjusting, loading, filling, or unplugging. Keep working area clean and free of debris to prevent slipping or tripping. 6. Do not allow riders on the trailer or frame when transporting. 7. Keep hands, feet, hair, and clothing away from rotating parts. 8. Do not place hands, fingers, or arms between moving parts. 9. Stay away from overhead power lines. Electrocution can occur without direct contact. 10. Install and secure all guards before starting. 11. Use care when climbing on frame or ladder to prevent slipping or falling. 12. Fasten frame securely to trailer before transporting. 13. Always empty compartment 2 first to prevent an unbalanced load. An unbalanced load can cause the tender to upend. 14. 2.7 6. Always use personal protection devices, such as eye, hand, and hearing protectors, when performing any service or maintenance. 7. OEM 8. A fire extinguisher and first aid kit should be readily accessible while performing maintenance on this equipment. 9. Periodically tighten all bolts, nuts, and screws and ensure all cotter pins are properly installed to ensure unit is in safe condition. 10. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. 11. Turn OFF all electrical power and tag or lockout the power source before performing any electrical test or before connecting or disconnecting valve coils or other electrical loads. 12. Never operate or test any function of the equipment when people are in an area of a potential crush hazard. Review safety related items annually with all personnel who will be operating, using, or maintaining the seed delivery system. MAINTENANCE SAFETY 1. Good maintenance is your responsibility. Poor maintenance is an invitation for trouble. 2. Follow good shop practices. Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to the original specifications. The manufacturer will not be responsible for injuries or damages caused by use of unapproved parts and/or accessories. 2.8 LOCK-OUT OR TAG-OUT SAFETY 1. WARNING 3. Ensure proper ventilation. Never operate the engine in a closed building. The exhaust fumes may cause asphyxiation. 4. STOP Before working on this machine, shut off the engine and remove the ignition keys. do not operate signed by date 2. Train all operators and service personnel before allowing them to work around the seed delivery system. 3. WARNING do not operate signed by date 5. 16 Never work under equipment unless it is securely blocked. Establish a formal Lock-Out or Tag-Out program for your operation. Provide tags on the machine and a sign-up sheet to record tag-out details. 2.9 STORAGE SAFETY 2.11 REFUELLING SAFETY 1. Store the unit in an area away from human activity. 1. 2. Do not permit children to play on or around the stored machine. 2. Allow engine to cool for five minutes before refuelling. Clean up spilled fuel before restarting engine. 3. Do not refuel the machine while smoking or when near open flame or sparks. 3. Store the unit in a dry, level area. Support the frame with planks, if required. 2.10 1. G TRANSPORT SAFETY Comply with local, state, and federal laws governing safety and conveyance of farm machinery on public roads. 2. Ensure all lights, reflectors, and other lighting requirements are installed and in good working condition. Handle fuel with care. It is highly flammable. 4. Fill fuel tank outdoors. 5. Prevent fires by keeping machine clean of accumulated trash, straw, grease, and debris. 2.12 BATTERY SAFETY Keep all sparks and flames away from batteries, as gas given off by electrolyte is explosive. 3. Ensure that the trailer is equipped with brakes that are in good working order. Be familiar with their operation. 1. 4. Do not exceed a safe travel speed. Slow down for rough terrain and when cornering. 2. Avoid contact with battery electrolyte: wash off any spilled electrolyte immediately. 5. 3. Fasten frame securely to trailer before transporting. 6. Be sure the trailer is securely hitched to the towing vehicle and a retainer is used through the hitch jaws. Always attach a safety chain between the hitch and the towing vehicle. 7. Stay away from overhead power lines. Electrocution can occur without direct contact. Wear safety glasses when working near batteries. 4. Do not tip batteries more than 45 degrees, to avoid electrolyte loss. 5. To avoid injury from spark or short circuit, disconnect battery ground cable before servicing any part of electrical system. 8. Plan your route to avoid heavy traffic. 9. Install auger spout transport lock before transporting. 10. Do not drink and drive. 11. Be a safe and courteous driver. Yield to oncoming traffic in all situations, including narrow bridges, intersections, etc. Watch for traffic when operating near or crossing roadways. 12. Never allow riders on the tender or the trailer. 17 2.13 SIGN-OFF FORM Meridian Manufacturing Group follows the general Safety Standards specified by the American Society of Agricultural Engineers (ASAE) and Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the Meridian Manufacturing Group Bulk Seed Tender Model 400 SLD seed delivery system must read and clearly understand ALL Safety, Operating, and Maintenance information presented in this manual. Make these periodic reviews of SAFETY and OPERATION a standard practice for all of your equipment. We feel an untrained operator is unqualified to operate this machine. A sign-off sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understand the information in the Operator’s Manual and have been instructed in the operation of the equipment. Do not allow anyone to operate this equipment until such information has been reviewed. Annually review this information before the season start-up. SIGN-OFF FORM Date 18 Employee’s Signature Employer’s Signature 3. SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in the following pages. Good SAFETY AWARENESS requires that you familiarize yourself with the various safety signs, the type of warning and the area, or a particular function related to that area. 2. Product Serial Number Decal (#19984) REMEMBER - If safety signs have been damaged, removed, become illegible, or parts replaced without signs, new signs must be applied. New safety signs are available from your authorized dealer free of charge. 4 1 2 MMG-00270 1. CAUTION — Read and Understand (#19934) CAUTION • Read and understand the Operator’s Manual before using. Review safety instructions annually. • Stop engine, remove ignition key, and wait for all moving parts to stop before servicing, repairing, adjusting, loading, filling, or unplugging. • Keep working area clean and free of debris to prevent slipping or tripping. • Do not allow riders on the trailer or frame when transporting. • Only enter seed compartment when it is empty. • Keep hands, feet, hair, and clothing away from moving parts. • Do not place hands, arms, or body between seed box and frame or lid to prevent pinching or crushing. Components can move unexpectedly. • Do not place hands, fingers, or arms between unloading auger tube segments when placing in unloading configuration. • Stay away from overhead power lines. Electrocution can occur without direct contact. • Install and secure all guards before starting. • Use care when climbing on frame or ladder to prevent slipping or falling. • Do not smoke when refuelling or working around machine. • Fasten frame securely to trailer before transporting. • In two compartment seed tenders, always empty Compartment 2 first to prevent an unbalanced load. An unbalanced load can cause hitch to upend. 19934 3 5 MMG-00272 3. WARNING — Rotating Parts (#19936) ROTATING PART HAZARD KEEP AWAY To prevent serious injury or death from rotating parts: • Stop engine, remove ignition key, and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging. • Install and secure all guards before operating. • Do not operate with rotating parts exposed. 19936 19 4. WARNING — Fall Hazard (#19939) 6. WARNING — Automatic Operation (#15056) THIS MACHINE IS AUTOMATICALLY, AND REMOTELY CONTROLLED. THE HOPPER GATES WILL OPEN AND CLOSE DURING THE OPERATION OF THIS MACHINE WITHOUT WARNING. FALLING HAZARD Avoid serious injury or death from falling: Gri the ladder ith oth hands hen lim ing to revent sli ing or falling ee rungs lean to revent sli ing 5. WARNING — Hot Surface (#20088) 20 19939 DO NOT PLACE HANDS AND OR OTHER BODY PARTS THROUGH THE GATE OPENINGS WHILE OPERATING THIS MACHINE. MAINTAIN A SAFE DISTANCE WHILE OPERATING THIS MACHINE. 15056 7. WARNING — Pinch Point (#20087) 8. WARNING — Crush Hazard / Electrocution (#17509) CRUSH HAZARD Keep hands and arms clear of conveyor tube when placing it in storage position. Weight of tube will cause crushing injuries. ELECTROCUTION HAZARD Avoid contact with overhead power lines or electrically powered objects. • Be aware of your surroundings when raising or lowering conveyor. • Maintain at least 20 feet between equipment and any electrical hazard. • Contact with electricity can result in serious personal injury or death. 17509 9. Instruction — Release Conveyor (#15055) 10. Instruction — Capture Conveyor (#15057) 21 4. SPECIFICATIONS 4.1 OVERALL SEED TENDER SPECIFICATIONS 22 4.2 BOLT SPECIFICATIONS WARNING The torque value for bolts and capscrews are identified by their head markings. Replacing higher “Grade” bolts (Grade 8) with lower Grade bolts (Grade 5) will lead to equipment failure and can result in injury or death. Always use replacement bolts with the same Grade markings as the removed bolt. 4.2.1 Bolt Torque Values Torque figures indicated above are valid for nongreased or non-oiled threads and heads unless otherwise specified. Therefore, do not grease or oil bolts or cap screws unless otherwise instructed in this manual. When using locking elements, increase torque values by 5%. Bolt Diameter “A” SAE Grade 2 N·m (lb-ft) SAE Grade 5 N·m (lb-ft) SAE Grade 8 N·m (lb-ft) 1/4" 8 (6) 12 (9) 17 (12) 5/16" 13 (10) 25 (19) 36 (27) 3/8" 27 (20) 45 (33) 63 (45) 7/16" 41 (30) 72 (53) 100 (75) 1/2" 61 (45) 110 (80) 155 (115) 9/16" 95 (70) 155 (115) 220 (165) 5/8" 128 (95) 215 (160) 305 (220) 3/4" 225 (165) 390 (290) 540 (400) 7/8" 230 (170) 570 (420) 880 (650) 1" 345 (225) 850 (630) 1320 (970) 4.2.2 Grade Markings Chart Grade 2 Low or Medium Carbon Steel No Marking Grade 5 3 Radial Lines Medium Carbon Steel Quenched and Tempered Grade 8 6 Radial Lines Medium Carbon Alloy Steel, Quenched and Tempered 23 5. MACHINE COMPONENTS AND CONTROLS 5.1 COMPONENT NOMENCLATURE AND LOCATION The Meridian 400 SLD Seed Tender models are designed as bulk seed transfer units to transfer large amounts of seed into a planter or drill. Large bulk seed containers are loaded into the seed tender compartments (1 & 2) using two methods. The seed can be loaded into one of two compartments from a seed box or other means. The seed tender can also load itself using its conveyor (23). The center-mounted conveyor (7) then transfers the seed from the compartments into planters or drills. Slide gates (22) on the compartments control the flow of seed into the conveyor. A gasoline engine (12) mounted on the frame powers a hydraulic pump, which operates the hydraulic motor for the conveyor and the control cylinders (raise, lower, and rotate the conveyor; open and close the slide gates). (12) Gasoline Engine to Power Hydraulic Pump. (13) Coupling (Engine to Pump). (14) Hydraulic Pump. (15) Hydraulic Oil Filter. (16) Hydraulic Tank Oil Level Sight Gauge. (17) Hydraulic Tank. The conveyor is mounted on a pivoting platform (21) that rotates 135°. An optional spout on the end of the conveyor allows for convenient distribution. (1) Compartment 1. (2) Compartment 2. (3) Roll Tarp and Open/Close Bar. (4) Seed Tender Frame. (5) Control Panel and Wireless Remote Control (not shown). (6) Trailer (Standard or Gooseneck). (7) Conveyor in Planter Loading Position. (8) Delivery Spout. 24 (18) Hopper and Cover. (19) Breakaway Trailer Brake System. (20) Transport Lock (Field and Road). (21) Pivot Platform. (22) Bin Slide Gates and Cylinders. (23) Conveyor in Self-loading Position. 5.2 ENGINE AND CONTROLS A Honda® engine is used with the unit. Always read the engine Operator’s Manual supplied with the seed tender for the detailed operating procedures. 1 3. Choke Lever The choke lever controls the fuel/air mixture to the engine. Close the choke when starting if the engine is cold. Open the choke as the engine warms. Always open the choke fully during operation. 4. Fuel Shut-Off Valve Each engine is equipped with a valve between the fuel tank and the carburetor. Slide the fuel valve toward the block to turn ON and away for OFF. Turn the fuel OFF when not in use or before transporting. 2 5. Throttle Lever This lever controls the engine RPM. Move the lever laterally to increase or decrease the RPM. Always run at maximum throttle while operating. MMG-00249 1. Electrical System Key Switch (located in Control Box 5) This key switch controls the power to the electrical system. Turn the key clockwise to turn the electrical system ON. The key must be in the ON position for the engine to start. Turn the key counterclockwise to stop the engine and turn OFF the electrical system. 2. Engine Start Button (located in Control Box 5) Press and hold this button until the engine starts. Also set the choke lever on the engine when starting the engine. Turn the key switch counterclockwise to turn OFF the engine. 5. 6. Starting Rope This retracting rope and T-handle is an optional method used to turn the engine over for starting. Grasp the T-handle firmly and pull the rope sharply to start the engine. Key on master control must be ON to pull-start. 7. Battery (12 Volt) A 12 Volt battery supplies the power to start the gasoline engine. When the engine is operating a trickle charge is sent to the battery to keep it fully charged. 25 5.3 CONTROL SYSTEM FUNCTIONS The MEGA REMOTE system is a state‑of‑the‑art microprocessor based Radio Frequency (RF) control system. It provides the operator the ability to operate the seed tender from the control panel or from the wireless handheld remote transmitter. 5.3.1 Control Functions The controls on this panel are intended to be used only as a backup resource. All of the functions of the seed tender can more easily be controlled using the handheld remote transmitter. 3 1 9 10 11 12 2 Conveyor Swing Left and Swing Right (5) This switch positions the conveyor to the right or left. Press the switch to the LEFT to position the conveyor towards the front of the unit. Press the switch to the RIGHT to position the conveyor towards the rear of the unit. Conveyor Start and Stop (6) This toggle switch starts and stops the conveyor belt. Press the toggle switch UP to start the conveyor. Press the toggle switch DOWN to stop the conveyor. Slide Gate 1 (7) This switch opens and closes the slide gate at the bottom of the compartment 1. Press and hold the switch UP to open the slide gate; press and hold the switch DOWN to close the slide gate. The opening can be varied to provide the desired flow rate of seed onto the conveyor belt. 5 Slide Gate 2 (8) This switch opens and closes the slide gate at the bottom of compartment 2. Press and hold the switch UP to open the slide gate; press and hold the switch DOWN to close the slide gate. The opening can be varied to provide the desired flow rate of seed onto the conveyor belt. 4 6 13 7 8 MMG-00279 On/Off Key Switch (1) This key switch controls the power to the electrical system. Turn the key clockwise to turn the electrical system ON. The key must be in the ON position for the engine to start or the handheld remote transmitter to function. Turn the key counterclockwise to turn OFF the electrical system. Starting the Engine (2) Press and hold this button until the engine starts. Also set the choke lever on the engine when starting the engine. Turn the key counterclockwise to turn OFF the engine. LCD Display (3) Turning key switch (1) to the ON position will turn the LCD backlight ON. It will stay on until the key is turned to the OFF position. Conveyor Lift and Lower (4) This switch raises and lowers the conveyor. Press the switch UP to raise the conveyor. Press the switch DOWN to lower the conveyor. Increase (9) Increases the weight when setting the Weight to Dispense function. From the Main Display screen, to lighten the LCD display contrast press the Increase button. Press and hold both the Increase and Decrease buttons simultaneously for ten seconds to enable or disable the display screen. Decrease (10) Decreases the weight when setting the Weight to Dispense function. From the Main Display screen, to darken the LCD display contrast press the Increase button. Press and hold both the Increase and Decrease buttons simultaneously for ten seconds to enable or disable the display screen. Scroll (11) Press the scroll button to scroll between the various display pages. — Main Display screen (shows weight) — Weight To Dispense screen (shows amount of seed that will be delivered to planter) — Active Slide Gate screen — Auto Reset screen 26 Tare (12) To “Tare” or zero the scale when the receiver display is on the main display page showing the weight, press and hold the tare push button on either the remote transmitter or the receiver for three seconds. The display will then show the weight as zero. RS232 Connector for Diagnostics (13) 5.3.2 Setting the Weight to Dispense 1. Select the Weight To Dispense screen using scroll button (11). 2. Press and hold Tare button (12) for five seconds. 3. The first character of the weight will start blinking. 4. Use the Increase (9) or Decrease (10) buttons to select the appropriate number. 5. Use the Scroll button to move to the next digit. Use the Increase (9) or Decrease (10) buttons to select the appropriate number. Repeat this until the desired weight has been entered. 6. Finally, holding the Tare button for another five seconds to save the new weight. NOTE: The weight of the seed is calculated when it is inside the compartments and as it flows through the slide gates. Any seed in the seed pan or the conveyor has already been weighed and does not affect the total weight. 5.3.3 Setting Active Slide Gate 1. Select the Active Slide Gate screen using scroll button (11). 2. Use the Increase/Decrease buttons to set the slide gate to either #1 or #2. 3. When the Auto Reset button is pressed on the remote transmitter, the slide gate selected will open automatically. 5.3.4 Auto Reset Function 1. Using the Weight To Dispense screen, select the desired weight of seed to be delivered to the planter. 2. Using the Active Slide Gate screen, select either compartment 1 (Slide Gate 1) or compartment 2 (Slide Gate 2). 3. Press the Auto Reset button on the remote transmitter. The unit monitors the weight of seed being dispensed. As the weight approaches the desired Weight To Dispense, the slide gate will begin to close. If the weight stops changing too soon, the unit will open the slide gate slowly in order to get the desired amount. 5.3.5 Control System Compliance Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to the reception of other electronics, which can be determined by turning the equipment off and on, DO NOT operate this equipment around those devices. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with nonapproved equipment or unshielded cables is likely to result in interference to electronic device reception. The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment. 27 5.4 WIRELESS REMOTE TRANSMITTER Each radio remote transmitter is designed to operate with a unique radio ID code and RF channel sequence. Each receiver is programmed to respond only to the remote transmitter with the correct ID code/RF channel sequence for which it is set. This feature allows multiple systems to work in close proximity to one another without interference. 5.4.1 Functions of Keypad Buttons Use the buttons on the keypad to operate the desired functions of the seed tender. If the remote transmitter goes out of range for more than two seconds, all outputs except CONVEYOR will turn off as a safety feature. In the event that a remote transmitter becomes damaged and a new one is needed, the receiver can be reprogrammed to respond to the new remote transmitter. Refer to “10.1.3 Remote Control Transmitter and Receiver Synchronization” on page 48 of this manual. All of the normal functions of the seed tender can be controlled by the remote transmitter. POWER (1) Press Power button (1) to turn remote transmitter ON. Press and hold the button to turn it OFF. To save battery life, the remote transmitter will automatically turn off when it is idle (no functions are used) for a period greater than the sleep time (default is 15 minutes). Refer to “10.1.4 Changing Sleep Time on the Transmitter” on page 49 to change the sleep time on the transmitter. NOTE: The remote transmitter will NOT automatically shut off as long as the receiver has power applied to it. ENG STOP (2) Press Engine Stop button to turn OFF engine. CONV (3) The Conveyor button starts and stops the conveyor belt. Press the INC button to start the conveyor. Press STOP button to stop conveyor. GATE 1 (4) The Slide Gate 1 buttons open and close the slide gate at the bottom of compartment 1. Press the OPEN button to open the slide gate, and press the CLOSE button to close the slide gate. The opening can be varied to provide the desired flow rate of seed onto the conveyor belt. 28 CONV (5) This Conveyor button positions the conveyor to the right or left. Press the LEFT button to position the conveyor towards the front of the unit. Press the RIGHT button to position the conveyor towards the rear of the unit. TARE (8) The tare button will reset the scale to zero in order to measure only the content being added to one compartment without measuring the weight of the seed tender itself. This allows an exact measurement of the seed to be placed in the compartment. ENG START (9) Press the engine start button to start the engine. If the engine has not been started recently set the choke to ON. GATE 2 (6) The Slide Gate 2 buttons open and close the slide gate at the bottom of compartment 2. Press the OPEN button to open the slide gate, and press the CLOSE button to close the slide gate. The opening can be varied to provide the desired flow rate of seed onto the conveyor belt. CONV (7) This Conveyor button raises and lowers the conveyor. Press the LIFT button to raise the conveyor. Press the LOWER button to lower the conveyor. AUTO RESET (10) Pressing the AUTO RESET button on the remote transmitter will dispense the Weight To Dispense out the selected gate. The gate that was selected in the Active Gate screen will open in #s. The unit will monitor the weight being dispensed. As the weight approaches the desired Weight To Dispense, the gate will begin to close. If the weight stops changing too soon, the unit will open the gate slowly in order to get the desired amount. 1. The auto reset mode does not turn the CONVEYOR on. The desired speed for the CONVEYOR should be set manually. 2. If the transmitter is in the middle of auto dispense mode and the remote goes out of range, the unit will close all open gates regardless the status of dispensing. 3. If the remote goes into the sleep mode during the auto dispense mode, the unit will abort the auto dispense mode and close the active gate. 4. Pressing any of the gate function buttons on the transmitter will close the active gate and stop the auto dispense mode. 5. If during the auto dispense mode the POWER button is pressed, the active gate will close. 29 ENABLE/DISABLE DISPLAY Hold both INCREASE and DECREASE push buttons on the control panel simultaneously for 10 seconds to enable or disable the display. BAR PAGE On the BAR PAGE where all weights are shown separately, holding down the TARE button on the control panel for 10 seconds will zero the reading for all the bars. 5.4.2 Display Panel If the “NO LINK” message appears, the remote transmitter is not communicating with the control panel on the seed tender. Make sure the ON/OFF key switch is in the ON position. (1) Weight Displayed in Pounds. (2) Signal Strength. (3) Percentage of Battery Life. 5.4.3 Display Messages Pressing the POWER button turns the remote transmitter ON and displays the message “Meridian Mega Remote”. 30 The remote transmitter will display the WEIGHT of the seed in the seed compartments in pounds. It also displays the battery life of the two AA batteries in a percentage of remaining life. When the POWER button is pressed and held, the message “Transmitter is turning OFF” will be displayed. 6. 6.1 PRE-OPERATING INSTRUCTIONS MACHINE BREAK-IN PERIOD A special break-in procedure has been developed to ensure the integrity of the seed tender when first put into service. Follow the Before Starting instructions and then follow the Inspections for 1/2, 5, and 10 Hours instructions at the appropriate interval. After completing these instructions, follow the normal service schedule in the Maintenance section and engine manual. 6.1.1 Before Starting 1. Read and follow the instructions in the Honda® engine and the Meridian Operator’s Manuals. 6.1.2 Inspections for 1/2, 5, and 10 Hours 1. Recheck machine fluid levels. Refill as required. 2. Recheck the tension and alignment of the delivery belt. 3. Recheck hardware and fasteners; frame to trailer tie-downs, all fasteners, and wheel bolts. Tighten to their specified torque. 4. At 10 hours, change the engine oil with the specified oil. 2. Review and follow Set-Up Instructions and the Pre-operation Checklist before starting machine. 3. Initially check wheel bolt torque and then again at 10, 25, and 50 miles. Refer to the Wheel Bolt Torque Requirements section in this manual for tightening instructions. 4. If needed, adjust the height of the hitch assembly. Refer to the appropriate hitch section in this manual for either the standard trailer hitch or the gooseneck hitch. 5. Start the engine and check the controls. Be sure that they function properly. 31 6.2 PRE-OPERATION CHECKLIST 9. Check the fluid level in the hydraulic tank. Add fluid as needed. Efficient and safe operation of the Meridian Bulk Seed Tender system requires that each operator reads and follows the operating procedures and all related safety precautions outlined in this section. 10. Check the tension of the delivery belt. Follow the instructions in the manual to correct the tension and/or alignment. A pre-operational checklist is provided for the operator. It is important for both personal safety and maintaining the efficient operation of the delivery system that this checklist be followed. 11. When the machine is operating, check the alignment of the delivery belt. Follow the instructions in the manual to correct the tension and/or alignment. Before operating the delivery system and each time thereafter, the following areas should be checked: 1. Lubricate the machine, as outlined and shown in the Grease/Lubrication Location Diagram in the Maintenance section of this manual. Follow the prescribed schedule. 2. Check the engine fluid levels, fuel, and crankcase oil. Add as required. IMPORTANT The engine warranty is void if the engine is run without oil. 3. Check hardware and fasteners; seed tender frame to trailer tie-downs, hitch bolts, trailer hitch to trailer bolts, and all other fasteners. Tighten to their specified torque. 4. Make sure the wheel bolt lug nuts are tight. 5. Check the tires and ensure that they are inflated to their specified pressure. 6. Remove all entangled material. 7. Visually inspect the conveyor and frame for damage. 8. Test the breakaway brake unit and the trailer brakes. • Make sure the trailer brakes are operating properly. • Make sure the trip wire to the breakaway switch is connected to the tow vehicle. • Make sure the pin is correctly installed in the breakaway switch. • Press the Test button. The indicator should illuminate green. If the red light illuminates, the battery charge is low. Refer to the Breakaway system in the Maintenance section for instructions on charging the battery. 32 7. OPERATION OPERATING SAFETY • • • • Make sure that anyone operating the seed delivery system or working on or around the unit reads and understands all the operating, maintenance, and safety information in the Operator’s Manual. Keep all bystanders, especially children, away from the machine when loading or unloading is being done, or when authorized personnel are carrying out maintenance work. Establish a lock-out tag-out policy for the worksite. Be sure all personnel are trained in and follow all procedures. Lock-out tag-out all power sources before servicing the unit or working around loading/unloading equipment. Stop engine, remove ignition key, and wait for all moving parts to stop before servicing, repairing, adjusting, loading, filling, or unplugging. • Keep working area clean and free of debris to prevent slipping or tripping. • Do not allow riders on the trailer or frame when transporting. 7.1 CONNECTING THE TRAILER WARNING • Keep hands, feet, hair, and clothing away from moving parts. • Do not place hands, arms, or body between the seed box and frame or lid to prevent pinching or crushing. Components can move unexpectedly. • Stay away from overhead power lines. Electrocution can occur without direct contact. • Install and secure all guards before starting. • Use care when climbing on frame or ladder to prevent slipping or falling. • Do not smoke when refueling or working around machine. • Fasten frame securely to trailer before transporting. • Review safety related items annually with all personnel who will be operating, using, or maintaining the seed delivery system. 2. Use the trailer jack to lift the hitch above the height of the receiver on the tow vehicle (standard hitch assembly shown). To prevent serious injury or death from upending hazard, do not stand over hitch when unhooking the trailer from the tow vehicle. Load or fill compartment 1 first to keep weight on the hitch. Unload or empty compartment 2 first to keep weight on the hitch. 7.1.1 Bumper Hitch 1. Complete the Pre‑operation Checklist. CAUTION Ensure that all bystanders, especially small children, are clear of the working area. Ensure there is enough room and clearance to safely back up to the machine. 33 3. Slowly back the tow vehicle until the hitch and ball are aligned. 7.1.2 Gooseneck Hitch 4. Lower the hitch onto the ball. 1. Adjust the trailer jack to set the trailer in a level position. 5. Raise the jack and place it in its stowed position. 6. Release the latch to lock the hitch around the ball and install the retainer clip to secure the connection. 7. Attach the safety chain securely to the truck frame to prevent unexpected separation. Cross the chains when attaching. WARNING Crush Hazard. The adjustable height tube in Step 2 is very heavy and can cause severe injury if it falls free. Once the lock bolt is loosened and the hitch pin is removed, the tube is free to fall to the ground if not properly supported. 2. Loosen lock bolt (1) on the adjustable height tube. Remove the keeper pin (2) and remove the tube lock pin (3). 8. Connect the wiring harness for the lights and brakes. 9. Connect the breakaway system cable to the tow vehicle. 10. Route all the cables in a manner that will prevent snagging. Be sure to provide slack for turning. 34 3. Adjust the tube height for the tow vehicle which would keep the trailer in a level position. 7.2 OPENING AND CLOSING ROLL‑UP TARP 4. Reinstall the pin and keeper. Tighten the tube lock bolt. 1. Remove the retaining pin from the crank holder. Using both hands, carefully remove the crank from the holder. 5. Raise the gooseneck ball hitch to go over the lowered tailgate of the tow vehicle and to clear the height of the gooseneck ball. 6. Open the clamp latch on the gooseneck coupler. MMG-00257 2. Extend the crank handle assembly to a comfortable operating position. 3. Roll the tarp to the fully opened position. 7. Position the trailer’s coupler directly over the ball in the bed of the tow vehicle. 8. Lower the gooseneck trailer into position and latch the clamp. 9. Attach the safety chains. 10. Connect the trailer light wiring to your vehicle’s connector and check all of your lights, including your brake lights. 11. Completely raise the trailer jack to the storage/ transport position. MMG-00259 4. Place the crank back in the holder and reinsert the pin. MMG-00258 35 7.3 OPERATION 3. Open the roll‑up tarp. 7.3.1 Conventional Loading (Filling the Seed Tender) This Operation section provides a step-by-step procedure for first loading seed into the seed tender compartments by 1) using the self‑filling feature at the farm or 2) using the conventional top fill method. It then shows how to unload the tender into a planter in the field or another type of container. 1. Connect the seed tender to a tow vehicle of sufficient size to safely transport the unit to its desired destination. SAFETY INSTRUCTIONS CAUTION Always load compartment 1 first to maintain a positive tongue weight. Negative tongue weight can cause the hitch to rapidly swing upward if not securely fastened to the tow vehicle, which can result in personal injury. 4. Fill the front seed compartment first to maintain a positive tongue weight. NOTE: Two sample slide gates, one in each compartment, can be used to retrieve samples of the seed from the compartment. To prevent possible injury, do not load the seed tender unless it is securely fastened to a tow vehicle. 2. Before loading the seed tender compartments, make sure the two slide gates are in the fully closed position. The gasoline engine (hydraulic system) must be operating to close the hydraulically controlled slide gate cylinders. MMG-00335 5. Close the roll‑up tarp and secure the handle in the storage position. MMG-00323 MMG-00258 36 7.3.2 Loading Using Self‑Filling Feature (Filling the Seed Tender) Using the self‑filling feature, the seed compartments can be loaded with the seed tender’s conveyor from a storage box, storage bin, grain truck, or other means directly into the seed compartments. 1. Unlatch the conveyor arm from the transport position by releasing the latch. 3. 2. If not already removed, remove the protective cover from the seed pan. It may be necessary to lower the hopper in order to remove the cover. To lower the hopper, pull out on the sliding lock collar and raise the handle to lower the hopper. Turn the key switch to the ON position. 4. Move fuel valve lever (2) to the ON position. 5. To start a cold engine, move choke lever (1) to the CLOSED position. MMG-00325 6. Start the engine and move throttle lever (3) to run the engine at full speed. 37 7. Using the remote control unit or the control panel, slightly raise the conveyor from the transport position. MMG-00324 NOTICE The indicator mark and the alignment plate must be aligned for the conveyor arm locking pin to engage. This pin locks the inner and outer tubes of the conveyor arm together. These two tubes must be locked together before releasing the conveyor hitch receiver (ball coupling). If the tubes are not locked together, the inner tube will slide down inside the outer tube and will require an external lifting device to raise it back into the correct position. MMG-00322b 8. Using the remote control unit or the control panel, rotate conveyor to align the triangular indicator on the conveyor pivot plate with the alignment plate on the frame, as shown. 9. To lock the conveyor arm tubes together, pull the handle of the lock pin outward slightly and rotate it 90° counterclockwise. 1 2 MMG-00328 38 10. Release and push the lock pin inward to lock the inner and outer tubes of the conveyor arm together. Make sure the pin is fully engaged. 13. Slide the ball coupling out of the conveyor hitch receiver. MMG-00329 11. Once the tubes are locked together, move the toggle switch downward to unlock the conveyor hitch receiver (ball coupling) on the conveyor. CRUSH HAZARD Keep hands and arms clear of conveyor tube when placing it in storage position. Weight of tube will cause crushing injuries. ELECTROCUTION HAZARD Avoid contact with overhead power lines or electrically powered objects. • Be aware of your surroundings when raising or lowering conveyor. • Maintain at least 20 feet between equipment and any electrical hazard. • Contact with electricity can result in serious personal injury or death. 17509 Be observant of overhead power lines or other electrical hazards. 14. When the ball coupling is free of the conveyor hitch receiver, lift the bottom of the conveyor arm over the fender and hold it off the ground until it is in its final position. MMG-00330 WARNING 12. Rotate hopper guide handle 90° into the position shown. If two people are positioning the conveyor arm, one at the controls and the other holding the conveyor arm, be extremely careful to prevent a crush hazard. Do not place any part of your body between stationary and moving parts. MMG-00326 39 15. Use the conveyor left or the conveyor right buttons (switches) to position conveyor arm into the desired position. The photos show the self‑filling position. 40 16. If desired, release the stand lock pin and rotate the stand downward. Engage the lock pin when the stand is fully extended. CAUTION To prevent personal injury, do not use the conveyor if the guard (metal bars) has been removed. CAUTION Always load compartment 1 first to maintain a positive tongue weight. Negative tongue weight can cause the hitch to rapidly swing upward if not securely fastened to the tow vehicle, which can result in personal injury. 17. Raise the hopper by pulling the lock collar outward and lowering the handle. Lock the handle into place when the hopper is at the desired height. 18. Start the conveyor. Refer to section 5.3 for setting automatic seed delivery functions. Do not open the slide gates when the conveyor is in the self‑filling position. 41 19. Allow the seed to flow into the conveyor from the external source to fill the seed tender or other container. MMG-00324 22. Lower the hopper. Raise the stand, if used. 23. Guide the ball coupling into conveyor hitch receiver. Make sure ball coupling is free of dirt and debris before placing it into the receiver. 20. When the seed tender or other container is filled, stop the conveyor. 24. Press and hold the toggle switch upward to lock the ball coupling into the conveyor hitch receiver. MMG-00330a 21. Return the conveyor arm to the storage position by first rotating the conveyor arm to align the triangular indicator on the conveyor pivot plate with the alignment plate on the frame, as shown. 42 25. Pull out on locking pin and rotate 90° clockwise to shield toggle switch. Release the locking pin and make sure it is firmly seated in the open position. NOTE: Two sample slide gates, one in each compartment, are used to retrieve samples of the seed from the compartment. 2 1 3 MMG-00335 MMG-00331 29. If necessary, close the roll‑up tarp and secure the handle in the storage position. 26. Rotate conveyor to the transport position; either front or back. 27. Lower the conveyor arm onto transport support and lock into place with latch. MMG-00258 7.3.2 Unloading (Filling the Planter) CAUTION MMG-00322a NOTE: Do not move the seed tender unless the conveyor is locked in the transport position. CRUSH HAZARD Keep hands and arms clear of conveyor tube when placing it in storage position. Weight of tube will cause crushing injuries. ELECTROCUTION HAZARD Avoid contact with overhead power lines or electrically powered objects. • Be aware of your surroundings when raising or lowering conveyor. Always unload compartment 2 first to maintain a positive tongue weight. Negative tongue weight can cause the hitch to rapidly swing upward if not securely fastened to the tow vehicle, which can result in personal injury. 1. Before unloading, shut off engine on the tow vehicle, set the parking brake, and remove the ignition key. • Maintain at least 20 feet between equipment and any electrical hazard. • Contact with electricity can result in serious personal injury or death. 17509 Be observant of overhead power lines or other electrical hazards. 28. Move the seed tender to the location of the planting equipment following all safe towing practices. 43 2. Unlatch conveyor from the transport position by releasing the latch. CRUSH HAZARD Keep hands and arms clear of conveyor tube when placing it in storage position. Weight of tube will cause crushing injuries. ELECTROCUTION HAZARD Avoid contact with overhead power lines or electrically powered objects. • Be aware of your surroundings when raising or lowering conveyor. • Maintain at least 20 feet between equipment and any electrical hazard. • Contact with electricity can result in serious personal injury or death. 17509 Be observant of overhead power lines or other electrical hazards. 9. Position the conveyor to place the spout over the planter’s seed box. 3. If necessary, remove the protective cover from the hopper. MMG-00325 4. Turn the key switch on the control panel to the ON position. 5. Move the fuel valve lever to the ON position. 6. To start a cold engine, move the choke lever to the CLOSED position. 7. Start the engine and move the throttle lever to run the engine at full speed. 8. Slightly raise the conveyor out of the transport position. MMG-00322b 44 10. Position the hopper to prevent spillage of the seed. Make sure the handle is locked into the desired position before opening the seed compartment slide gates. 11. Manually start the conveyor or use the Auto Reset feature to automatically dispense a preselected amount of seed. Refer to section 5.4 Auto Reset Function for instructions. 13. When the planter is filled, close the slide gate and then stop the conveyor belt. CAUTION Always unload compartment 2 first to maintain a positive tongue weight. Negative tongue weight can cause the hitch to rapidly swing upward if not securely fastened to the tow vehicle, which can result in personal injury. 12. Open the slide gate on either compartment 1 or 2 with the remote control unit or the control panel for the desired seed flow. 14. Return the conveyor to the transport position and latch before moving the seed tender. The button and/or switch is only activated while pressed and held. The flow of seed into the conveyor can be controlled by the amount the slide gate is opened. 45 8. 8.1 STORAGE GENERAL INFORMATION After planting or when the machine will not be used for a period of time, completely inspect all major systems of the seed tender. Replace or repair any worn or damaged components to prevent unnecessary downtime at the beginning of the next season. IMPORTANT To prevent component damage, store the seed tender in a dry, level area. If the seed tender is not attached to a trailer, support the frame with planks to raise the unit off the ground. 8.2 PLACING IN STORAGE CAUTION Store the unit in an area away from human activity. To prevent the possibility of serious injury, do not permit children to play on or around the stored machine. 1. Remove all seed from the seed tender. 2. Place the gasoline engine fuel valve in the OFF position. 3. Thoroughly wash the machine with a pressure washer or water hose to remove all dirt, mud, or debris. 4. Inspect rotating parts for entangled material. Remove all entangled materials. 5. Check the condition of the conveyor belt. Replace or adjust, as required. 6. Check the condition of the hydraulic pump to engine shaft connectors and spider. Replace or adjust, as required. 7. Touch up paint nicks and scratches to prevent rusting. 8. Remove the ignition key and store in a secure place. 9. Remove the battery and store it in a cool, dry area on wooden blocks or a wooden pallet. Charge it monthly to maintain an adequate charge. 10. It is best to store the machine inside and if that is not possible, cover with a waterproof tarp and tie down securely. 46 8.3 REMOVING FROM STORAGE When removing the machine from storage, follow this procedure: 1. Remove the tarp, if covered. 2. Install and connect the battery. 3. Review and follow the Pre-Operation Checklist. 4. Review and follow the Service Checks in the Maintenance section. IMPORTANT If the machine has been stored for more than twelve months, warm the engine by running it for two to three minutes and drain the oil. Change the oil while the oil is warm to remove any condensation. Refer to the Engine Oil Change in the Maintenance section. 9. MAINTENANCE MAINTENANCE SAFETY • Good maintenance is your responsibility. • Follow good shop practices. - Keep service area clean and dry. - Be sure electrical outlets and tools are properly grounded. - Use adequate light. • Make sure there is plenty of ventilation. Never operate the engine in a closed building. Exhaust fumes may cause asphyxiation. • Before working on this machine, shut OFF the engine, and remove the ignition keys. • Never work under equipment unless it is securely blocked. • Always use personal protection devices, such as eye, hand, and hearing protectors when performing any service or maintenance. • Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to the original specifications. The manufacturer will not be responsible for injuries or damages caused by use of unapproved parts and/or accessories. • A fire extinguisher and first aid kit should be readily accessible while performing maintenance on this equipment. • Periodically tighten all bolts, nuts, and screws and check that all cotter pins are properly installed to ensure the unit is in a safe operating condition. • When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. 9.1 GREASING Use the Service Checks information in the Maintenance section to keep a record of all scheduled maintenance. 1. Use an SAE multi-purpose high temperature grease or a multi-purpose lithium base grease. 2. Use only a handheld grease gun for all greasing. An air-powered greasing system can damage the seals on bearings and lead to early failures. 3. Wipe grease fitting with a clean cloth before greasing to avoid injecting dirt and grit. 4. Replace and repair broken fittings immediately. 5. If fittings will not take grease, remove and clean thoroughly. Also, clean lubricant passageway. Replace fitting if necessary. 9.2 GREASE FITTING LOCATIONS The lift cylinder is equipped with grease zerks on each end. MMG-00261 Each wheel hub is equipped with a grease zerk under the center dust cap. MMG-00260 47 10. 10.1 SERVICE PROCEDURES REMOTE CONTROL UNIT The remote transmitter unit is powered by two AA batteries. The display window on the remote transmitter indicates the remaining battery life. When batteries are new, the display indicates 100% power. As the remote transmitter is used, the power decreases. When red indicator light (2) turns ON, the batteries should be replaced immediately, or discontinue the use of the remote transmitter. 10.1.2 Battery Replacement 1. Remove the two Phillips head screws from the cover on the back of the unit. 2. Replace the batteries, making sure they are correctly positioned. 10.1.1 Battery Replacement Tips • Check the batteries at least every six months (for low Voltage, leakage, etc.). • Always use the correct size and type of battery. Replace old batteries with new 1.5 Volt AA, alkaline batteries. • Always replace both batteries at the same time. • Do not mix types, brands, or ages of replacement batteries. • Do not install the batteries backwards. Make sure you insert the batteries with the + (plus) and – (minus) terminals aligned correctly. • Remove the batteries from the controller if not expected to be in use for several months. • Do not attempt to recharge a battery unless it is specifically marked “rechargeable.” • Dispose of old batteries properly. 10.1.3 Remote Control Transmitter and Receiver Synchronization To reprogram the ID code to the receiver, use the following procedure. NOTE: Do not interrupt this procedure before it has completed or the system may not operate correctly. 1. Turn the remote transmitter and receiver OFF. 2. Press and hold the POWER button on the handheld remote transmitter for more than ten seconds. The LCD display will indicate when to apply power to the receiver. 3. When directed, apply power to the receiver. Green LED stays on constantly when reprogramming is in progress. 4. When the process is completed, the green LED will blink on and off. Test the remote transmitter to make sure it functions properly. 48 10.1.4 Changing Sleep Time on the Transmitter 10.2 HYDRAULIC SYSTEM 10.2.1 Hydraulic Oil Change To change the sleep time on the transmitter, use the following procedure. 1. With the transmitter off, press and hold ENGINE STOP, CONVEYOR STOP and POWER button. 2. Wait for a few seconds, then release the buttons. 3. The green and red LEDs will start blinking together. 4. Use CONVEYOR INC and CONVEYOR STOP to increase/decrease the sleep time. 5. Select the desired sleep time. 6. Press POWER button to save and exit. 10.1.5 Weigh System Clean transmitter regularly with a damp cloth and mild detergent. Inspect electrical wiring for wear points or other damage. Repair as required. Inspect all connections for looseness or corrosion. Tighten and/or “seal” as necessary. CAUTION When performing any inspection or maintenance on the remote system, always use care to prevent injury or damage to the equipment. The following are general precautions, which should be closely followed in carrying out any maintenance work. Do not have hydraulic power available to the valves when performing electrical tests. Never operate or test any function if any person is in an area where they could be hurt by being hit or squeezed by the hydraulic equipment. Turn power off before connecting or disconnecting valve coils or other electrical An oil and filter change is recommended annually or every 400 hours of operation using an AW HVI Hydraulic ISO 32 oil. IMPORTANT Never run the hydraulic pump unless the hydraulic oil tank is full (indicated in sight level gauge). (1) 1. Place a large waste oil container under the tank drain port. The hydraulic tank holds approximately ten gallons of oil. 2. Drain the hydraulic tank by removing the drain plug from the tank. Allow the tank to drain completely. 3. Remove and replace the oil filter. Apply a thin coat of oil to the rubber seal of the new oil filter. Hand-tighten only. 4. Re-install the drain plug. 5. Fill the tank to the fill line at the top of the gauge with approximately ten gallons of AW HVI Hydraulic ISO 32 oil. Replace the cap. 6. Start the engine and cycle all the cylinders several times. loads. 7. Recheck the oil level in the tank and add as needed. 49 10.2.2 Hydraulic Pressure Relief Valves IMPORTANT There are two pressure relief valves (1 and 2) which have been factory preset for the most efficient operation of the seed tender. DO NOT adjust these relief valves. If the unit is not operating properly, refer to the Troubleshooting section, call an authorized dealer, or call the factory. 1 2 MMG-00262 10.2.3 Hydraulic Motor Coupling Changing the pump coupling does not require the hydraulic tank to be drained. If the pump must be disconnected, drain the hydraulic tank and be prepared to catch any oil that remains in the two hydraulic hoses. 4. Loosen the setscrews in each coupling half and remove the old couplings. Install new couplings on the engine shaft and the pump shaft. When completely assembled, the shaft length in each coupling half should be the same. Tighten the pump end setscrews to 78 to 87 lb-in. Do not tighten the engine shaft coupling at this time. 5. Place the urethane spider in the pump coupling. Align and install the pump and pump coupling. 6. Tighten the pump bolts to a “Grade 5” bolt toque for that size of bolt. Refer to the 4.2 Bolt Specifications section. 7. Slide the engine coupling against the other coupling half and tighten the setscrew. 8. Replace the orange protective cover. NOTE: If the adapter plate was removed, tighten the four retaining bolts to “Grade 5” bolt torque for that size of bolt. 10.3 ENGINE For any questions concerning the Honda® engine not provided in this manual, refer to the OEM manual that was provided with the seed tender. To contact Honda®, refer to the OEM Literature section in this manual. 1. Remove the orange protective cover from the adapter assembly. 10.3.1 Approved Fuel 2. Remove the two pump mounting bolts. Use a regular unleaded automotive gasoline for all operating conditions. The fuel tank capacity is 1.0 liter (2.1 US pints). 3. Pull the pump away from the adapter to separate the coupling halves. 50 10.3.2 Engine Oil Use a typical SAE 10W-30 or 10W-40 multiviscosity motor oil for normal operating conditions. Consult your engine manual for the recommended oil in cold temperatures. The crankcase capacity is 1.1 liters (1.16 US qt.). 10.3.3 Change Engine Oil 1. Review the Operator’s Manual for the engine. 2. Allow the engine to cool before changing oil. Draining works best when oil is warm. CAUTION Burn Hazard. Hot engine oil can burn skin. 10.5 BELT DELIVERY TUBE 10.5.1 Unplugging 3. Be sure the engine key switch is in the OFF position and the fuel valve is turned OFF. If the conveyor becomes plugged, follow this procedure: 4. Place a pan under the drain plug. 1. Position the conveyor with easy access to both ends. 5. Remove the drain plug and allow oil to drain for ten minutes. 6. Reinstall the engine drain plug and tighten. 7. Dispose of the oil in an approved container. Follow industrial disposal regulations. 8. Fill the engine with SAE 10W-30 oil for general usage. If the engine is operated in more extreme conditions, refer to the OEM manual for oil recommendations. 2. Stop the engine and remove the ignition key. Place a lock-out tag on the control box to prevent accidental starting of the conveyor. 3. Open the lower access door at the bottom of the conveyor and/or open the delivery spout cover. 9. Run the engine for one minute and recheck the oil level. Add oil as needed. 10.3.4 Clean Air Cleaner Check the air cleaner daily before each usage. Clean it every three months or 50 hours of operation (clean it more frequently when used in dusty conditions). 10.4 LOAD CELLS Four load cells are used with the weighing system. There is no maintenance required for these load cells. If the seed tender does not seem to be functioning correctly, refer to the Troubleshooting section, call an authorized dealer, or call the factory. 51 4. Remove obstruction. 5. Close and secure the lower access door and delivery spout cover. 10.5.2 Belt Tension Adjustment 2. Tighten or loosen the bolt to correct the tracking problem. 3. Place both locking nuts on either side of the lock plate and tighten the locking nuts together. 4. Start the conveyor and make sure the belt is tracking in the center of the drive drum. Readjust if needed. 10.5.4 Belt Replacement Use the old belt to thread the new belt into the delivery tube. 1. Unlatch and open the access door. MMG-00333 1. Loosen the locknut on each side of the belt tension mechanism. 2. Tighten the two adjusting bolts equally to 23 lb-ft. While holding the adjusting bolt in place, retighten both locking nuts. 3. Start the conveyor and make sure the belt is tracking in the center of the drive drum. If the belt is not tracking properly, use the Belt Tracking Adjustment procedure to correct the problem. MMG-00334 IMPORTANT The drive drum at the bottom of the conveyor must be square (drive shaft must be equal distance from end of unit) for the belt to track properly. 10.5.3 Belt Tracking Adjustment 2. Loosen the lower drive drum adjusting bolts to their loosest position. 3. Disconnect the two ends of the conveyor belt. 1. Loosen the locknuts on the adjusting bolt. 52 4. Attach the replacement belt to the end of the old conveyor belt. 5. Slowly pull the old belt out of the delivery tube and thread the new one into position. 6. Disconnect the old belt and connect the ends of the new belt together. 7. Readjust the belt tension. 8. Close and latch the access door. 9. Start the conveyor to make sure the belt is tracking properly. 10. Recheck the tension and alignment of the belt frequently during the first ten hours of operation and adjust as needed. IMPORTANT If the battery is weak or dead (red indicator, even after charging), as indicated by the indicator light, the battery must be replaced. 3. Plug the trailer into the tow vehicle. The yellow “Charging” light should be ON. 4. Test the system by pulling the pin out of the breakaway switch. The battery will activate the brakes. (Note: Do not use this kit as a parking brake). The battery should be charged and tested prior to each trailer outing. NOTE: Typically a belt will seat itself during the first ten hours of operation and then require less or no adjustment. 10.6 TRAILER BREAKAWAY SYSTEM 10.6.2 Changing Battery The battery in the breakaway system is rechargeable, but not replaceable. If the battery will not hold a charge, replace the unit. 10.6.1 Testing the Battery 1. Disconnect the trailer plug from the tow vehicle; otherwise, you are testing the tow vehicle’s battery. 2. Press the green TEST button on the control box located inside the frame of the trailer. The green indicator light should illuminate if the battery is fully charged. If the yellow or red indicator lights illuminate, the unit’s battery should be charged before towing the trailer. 53 10.7 WHEEL BOLT TORQUE REQUIREMENTS 10.8 TRAILER HITCH BOLTS The front hitch section of the seed tender is bolted to the trailer frame. This design allows the same trailer to use either a standard hitch assembly or a gooseneck trailer hitch. These hitch assemblies are interchangeable, if needed. Check the torque on the trailer hitch bolts at least once per year. Tighten the bolts to 115 lb-ft. 1. Initially check the wheel bolt torque at 5, 10, 25, and 50 miles and after each wheel removal. NOTE: Torque wrenches are the best method to ensure the proper amount of torque is being applied to a wheel nut. CAUTION To prevent injury due to possible dangerous separation of wheels from the axle, the wheel nuts must be maintained at the proper torque levels. Properly maintained wheel nuts prevent loose wheels and broken studs. 2. Tighten the wheel nuts in three stages. — First stage: 20 to 25 foot pounds. — Second stage: 50 to 60 foot pounds. — Third stage: 90 to 120 foot pounds. 3. Tighten the wheel nuts in a clockwise, cross‑axle alternating pattern. 54 MMG-00332 10.9 SERVICE RECORD CHART The chart on the following page should be copied and filled out as maintenance is performed on the machine. Refer to the Lubrication, Maintenance, and Service sections for additional instructions. 10.9 SERVICE RECORD CHART (CONTINUED) Date Serviced by 8 hours or daily Check Engine Fluid Levels Check Hydraulic Tank Oil Level Test Breakaway Brake System Inspect Tires Check Remote Control Battery Life Check Conveyor Belt Tension and Alignment 50 Hours or Weekly Clean Engine Air Intake Filter Check Tire Pressure Check Conveyor Belt Tension and Alignment Clean remote transmitter with a damp cloth and mild detergent. 200 Hours or SEMI/ANNUAL Adjust Brakes Inspect Brake Magnets 400 hours or annually Change Engine Oil Check Wheel Bolt Torque Check Frame and Trailer Hold-Downs Check Hydraulic Motor Coupling Check Conveyor Tube Slide Plates Check Load Cells Inspect Brake Lining Wear, Brake Cylinder, and Brake Wiring Grease Wheel Bearings and Check Hub for Wear Inspect Axle Grease Seal Inspect all electrical wiring connections for looseness or corrosion. Thoroughly Clean Machine 55 10.10 SERVICE CHECKS 10.10.1 Daily (8 Hours) WARNING 10.10.2 Weekly (50 Hours) 1. Change engine oil. 2. Clean or change engine air filter. Gasoline is a highly combustible fuel. Improper use, handling, or storage of gasoline can be dangerous. Never touch or fill a hot engine. DO NOT fill the engine’s fuel tank near an open flame while smoking or while engine is running. DO NOT fill tank in an enclosed area with poor ventilation. Wipe up spills immediately. 1. Check engine oil level and fill as needed. 2. Check engine fuel level and fill as needed. 3. Check hydraulic fluid level (1) and fill as needed. 3. Check the tension on the delivery belt. Adjust tension if needed. Refer to “10.5.2 Belt Tension Adjustment” on page 52 of this manual for instructions. 4. Check tire pressure. Inflate the tires to the recommended pressure stated on the tire. 10.10.3 Annually (400 Hours) 1. Check wheel bolt torque. Refer to 10.7 Wheel Bolt Torque Requirements section in this manual for tightening instructions. 2. Check frame and trailer hold-down bolts. 3. Check hydraulic motor to engine shaft coupling and spider. Refer to the Changing Hydraulic Motor Coupling section for instructions. 4. Thoroughly clean the seed tender. 4. Test trailer breakaway system. Refer to “10.6 Trailer Breakaway System” on page 53of this manual. 5. Initially check wheel bolt torque at 5,10, 25, and 50 miles. Refer to “10.7 Wheel Bolt Torque Requirements” on page 54 of this manual for tightening instructions. 6. Check remote transmitter battery life and change them, if needed. Refer to “10.1 Remote Control Unit” on page 48 of this manual for additional information. 7. Check delivery belt for proper tracking. Refer to “10.5.3 Belt Tracking Adjustment” on page 52 of this manual. 56 5. Check the tires for wear, and replace if needed. 10.11 AXLE MAINTENANCE 10.11.1 First 200 Miles 1. Adjust brakes. Refer to OEM manual for procedure. 10.11.2 3,000 Miles or 3 Months 1. Adjust brakes. Refer to OEM manual for procedure. 2. Check torque on wheel nuts. Refer to the section in this manual. 3. Inspection tires for wear. Refer to OEM manual for procedure. 10.11.3 6,000 Miles or 6 Months 1. Inspect brake magnets for wear. Refer to OEM manual for procedure. 2. Inspect suspension parts for wear. Refer to OEM manual for procedure. 10.11.4 12,000 Miles or 12 Months 1. Inspect brake lining wear, check brake cylinder for leaks, and inspect brake wiring for damage. Refer to OEM manual for procedure. 2. Grease the wheel bearings and check the hub for wear. Refer to OEM manual for procedure. 3. Inspect grease seal for leakage. Refer to OEM manual for procedure. 4. Inspect springs for any wear or loss of arch. Refer to OEM manual for procedure. 10.12 TIRES Check the tires for normal and/or abnormal tire wear. Replace tires that are damaged or worn beyond normal tread life. Refer to the axle OEM manual for a Tire Wear Diagnostic Chart. Replace the tires with Meridian part number 18131 or an equivalent tire: 3T235/80R16 TR643 Load Range E For Trailer Service Only 57 11. 11.1 OEM LITERATURE HONDA® ENGINE For any questions concerning the Honda® G340X Engine, refer to the OEM manual that was provided with the seed tender. Additional information can be obtained from: United States Power Equipment Division Customer Relations Office 4900 Marconi Drive Alpharetta, GA 30005-8847 (770) 497-6400 Honda® Canada, Inc. 715 Milner Avenue Toronto, ON M1B 2K8 (888) 946-6329 11.2 RETRACTABLE COMPARTMENT TARP For any questions concerning the Agri-Cover, refer to the OEM manual that was provided with the seed tender. Additional information can be obtained from: ACI Agri-Cover PO Box 508 Jamestown, ND 58402 Phone: (866) 414-5422 Fax: (701) 251-1512 customerrelations@agricover.com 11.3 AXLE For any questions concerning the Axis Products axle, refer to the OEM manual that was provided with the seed tender. An Owner’s Manual and parts listing is provided with the seed tender. Additional information can be obtained from: Axis Products, Inc. 3403 Reedy Drive Elkhart, IN 46514 Phone: (574) 266-8282 Three decals are also provided showing the correct operation and maintenance for the tarp. Attaching these decals is the responsibility of the purchaser. 58 12. 12.1 TROUBLESHOOTING TROUBLESHOOTING CHART PROBLEM Engine will not start. Conveyor belt will not start. Electrical or hydraulic functions are not working properly. CAUSE SOLUTION No fuel. Fill the fuel tank. Low engine oil. Fill the crankcase with oil. Cold engine. Open choke. Ignition key switch off. Turn ignition key switch on. Battery dead. Recharge or replace battery. Engine problem. Refer to engine manual. No power. Start engine and increase speed above 1400 RPM. Drive motor coupling. Repair or replace coupling. Belt tension. Increase belt tension. No hydraulic oil. Check oil level. Transmitter power is OFF. Turn Power ON. Receiver power is OFF. Turn Power ON. Battery cable or battery. Check battery cable and make sure battery is fully charged. Error in the control system. Check LED Error Code light. Improper ground. Check for proper grounding electrical circuit. Hydraulic valve or motor. Ensure hydraulic pump is working properly and hydraulic tank is filled with oil. Intermittent function. Check receiver antenna for damage and proper connection. Loose connector at the valve coil. 59 12.2 CONTROL PANEL INDICATOR LEDS 2 1 12.2.1 Error Code Outputs The receiver module can identify problems with the system in the form of an error code. Check red indicator light (1) on the receiver to diagnose system problems. Each of the outputs from the receiver module is designed with built-in short circuit and overload protection. The outputs can also detect a no‑load or broken wire condition. MMG-00300 These error conditions are indicated by the red LED indicator on the receiver module or the HISTOGRAM page on the optional Palm Pilot™. Refer to the Error Code Chart for explanation of the error codes. Green LED indicator light (2) will blink on the receiver during normal communication. The ON/OFF outputs will indicate an error under no load or broken wire status if NOT activated, and will detect a short if activated. 12.2.2 Error Codes Error Code Cause Solution 1 RF Communication Transmitter is OFF. Transmitter went into sleep mode. Interference in RF communication link. 2 Wrong ID Transmitter and receiver are not synchronized. 3 Scale Bar Fault RS-232 communication cable between scale unit and receiver is damaged, disconnected, or the scale unit is OFF. 4 Low Battery System voltage is below 10.5 Volts. 5 Conveyor Speed Fault Check for short or open circuit. 6 Engine Start Fault Check for short or open circuit. 7 Engine Stop Fault Check for short or open circuit. 8 Conveyor Lift Fault Check for short or open circuit. 9 Conveyor Lower Fault Check for short or open circuit. 10 Conveyor Left Fault Check for short or open circuit. 11 Conveyor Right Fault Check for short or open circuit. 12 Slide Gate 1 Open Fault Check for short or open circuit. 13 Slide Gate 1 Close Fault Check for short or open circuit. 14 Slide Gate 2 Open Fault Check for short or open circuit. 15 Slide Gate 2 Close Fault Check for short or open circuit. NOTE: Error codes are invalid during manual operation. 60 12.2.3 Control System Wiring Locations Pin Description A Conveyor Speed CR Proportional Output - Orange/Black B Engine Start Output C Engine Stop Output D Conveyor Lift Output - Red E Conveyor Lower Output - Blue F NC G NC H Power J NC K NC L Conveyor Left Output - White M Conveyor Right Output - Green N Ground O Slide Gate One Open Output – Red/Black P Slide Gate One Close Output – Blue/Black Q Slide Gate Two Open Output – Green/Black R Slide Gate Two Close Output- Black/White S NC T NC U NC V NC W NC X NC 61 13. WARRANTY 13.1 WARRANTY STATEMENT Limited Materials and Workmanship Warranty For Bulk Seed Tenders Meridian Manufacturing Group (hereinafter referred to as the Manufacturer) hereby warrants the Bulk Seed Tender(s) sold by it to be free from any defect in material or workmanship under normal use and service for a period of one (1) year from the date of shipment. The Manufacturer’s obligation under this warranty shall be limited to the repair or replacement only, FOB the original point of shipment, of any defective parts or portions of the seed tender or accessories manufactured by Meridian. Any warranty claim must be reported to the Manufacturer within one (1) year from the date of shipment. THIS WARRANTY IS SUBJECT TO THE FOLLOWING LIMITATIONS, PROVISIONS AND CONDITIONS: 1. This warranty does not apply: a) To any product sold by the Manufacturer where it is used in areas exposed to corrosive or aggressive conditions including salt water, acids, alkaloid, ash, cement dust, animal waste or other corrosive chemicals from either inside or outside the bin. b) For failures or defects arising out of damage during shipment or during storage on site. c) To materials replaced or repaired under this warranty except to the extent of the remainder of the applicable warranty. d) To damage resulting from misuse, negligence, accident or improper site preparation by others. e) If the product has been altered or modified by others. f) If in the case of coating failures the failure is the result of damage, lack of proper maintenance or failure to remove road salt or other contaminants that may have come in contact with the bin surface. g) To loss of time, inconvenience, loss of material, down time or any other consequential damage. h) For a function that is different than original designed intent. 2. The obligation of the Manufacturer under this warranty shall not arise unless the Manufacturer is notified and this warranty is presented together with a written statement specifying the claim or defect within thirty (30) days after the failure is first detected or made known to the owner and within one (1) year from the shipment date. The Manufacturer in its sole discretion shall determine if the claim is valid and whether correction of the defect or failure shall be made by repair or replacement of the materials. 3. The coating warranty is based on the manufacturer’s performance specification for Polyester Powder finishes and does not include repair of minor blemishes or rusting that is normally part of the general maintenance of the seed tender. This warranty does not cover excessive wear on interior coatings. See attachment for full Performance Specification details on Polyester Powder Finishes. 4. The obligation of the Manufacturer hereunder extends only to the original owner and to the Meridian dealer to whom the materials may have been initially sold. This warranty shall not be subject to any assignment or transfer without the written consent of the Manufacturer. 5. The customer shall acknowledge that it has made its own independent decision to approve the use of the supplied materials and also the specific fabrication and construction procedures utilized to complete the seed tender, and has satisfied itself as to the suitability of these products for this particular application. 6. The foregoing sets forth the only warranties applicable to said materials and said warranties are given expressly and in lieu of all other warranties, expressed or implied, statutory or otherwise, of merchantability or fitness for a particular purpose and all warranties which exceed or differ from said warranties herein are disclaimed by the Manufacturer. 7. The owners sole and exclusive remedy against the Manufacturer shall be limited to the applicable warranty set forth herein and the endorsements, if any, issued together with this document and no other remedy (including but not limited to the recovery of assembly or disassembly costs, shipping costs, direct, incidental, special, indirect or consequential damages for lost profits, lost sales, injury to person or property or any other loss, whether arising from breach of contract, breach of warranty, tort, including negligence, strict liability or otherwise) shall be available to the owner or Meridian Dealer or any other person or entitles whether by direct action or for contribution or indemnity or otherwise. 8. The financial obligation of the Manufacturer under this warranty shall be limited to the repair or replacement of the product as originally supplied and in no event shall exceed the original cost of the product supplied. 9. The Manufacturer shall not have any obligation under any warranty herein until all accounts for materials, installation and erection of the said product thereof and for labor and other work performed by the Manufacturer or its dealers have been paid in full by the owner. Warranty Claim Procedure 1. Registering product with Meridian Manufacturing. 2. Contact the dealer unit was purchased from upon discovery of any defects. 3. A completed warranty claim form submitted by dealer to Meridian warranty representative for review and course of action. 4. Warranty repair work will only be performed by Meridian, the dealer or an approved representative. No warranty work completed prior to approval. Failure to follow procedure may affect any or all reimbursement. 5. Claims will be adjudicated at the sole discretion of the manufacturer and in accordance with the terms and conditions of the applicable limited warranty. 6. A complete list of warranty procedures can be procured from the Warranty Department or found in your owner’s manual. Effective July 1, 2009 62 14. PARTS The following pages contain a list of serviceable parts for the 400 SLD Seed Tender unit. Parts are available from your authorized Dealer Parts Department. 14.1 400 SLD SEED TENDER 80137 14.2 - 8” CONVEYOR DETAILS 14.3 - LADDER DETAIL SLIDE GATE DETAIL SAMPLE GATE DETAIL 14.10 - GOOSENECK DETAIL 14.9 - BUMPER HITCH DETAIL 14.8 - TURRET DETAIL 14.7 - LIGHT AND DECAL DETAIL 14.6 - WEIGH SYSTEM DETAIL 14.5 - POWER SYSTEM DETAIL 14.4 - AXLE / WHEEL DETAIL 14.2 CONVEYOR (8”) 80634 14.2.4 — T 14.2.3 — TU 14.2.2— 14.2.1— T UT T T T 63 14.2.1 Pan Detail 5 28 27 30 31 32 29 26 33 25 24 7 8 9 34 6 35 23 22 10 36 21 16 15 14 13 18 17 20 19 37 12 11 9 8 7 38 10 4 5 Item Qty. Part No. 1 6 19301 2 2 19133 3 4 3 2 1 39 6 Description Item Qty. Part No. Description Bolt, Hex, 1/4-20 x 1” 21 2 20087 Decal, Pinch Point, Hand Bumper, Rubber 22 2 19447 Grip, Handle 19335 Bolt, Carriage, 3/8-16 x 1-1/2” 23 1 19095 Holder, Tool 4 1 19118 Ring, Snap, Square, Zinc, 3/8 x 2-1/4” 24 8 19310 Bolt, Hex, 5/16-18 x 1” 5 18 19564 Nut, Hex, Flanged, 3/8-16 25 42 19318 Nut, Hex, Flanged, 5/16-18 6 2 25248 Weldment, Scoop Bracket 26 2 19404 Bushing, Nylon 1” 7 4 27040 Housing, Roller Bearing 27 1 26029 Pin, Hopper Loop Pivot 8 4 21258 Bearing 28 1 25429 Guard, Hopper Weldment 9 4 Bearing, Collar 29 11 19560 Bolt, Hex, 1/4-20 x 3/4” 10 2 25842 Weldment, Roller Side Plate 30 12 19128 Nut, Hex, Nylon, 1/4-20 11 2 19069 Screw, Rnd Head Phillips, 3/8-16 x 1” 31 12 19307 Washer, Flat, 1/4 12 2 19349 Washer, Lock, 3/8” 32 1 25241 Seal, Hopper Retainer (Rear) 13 2 19093 Bearing, Roller, 7/8” OD 33 5 19126 Nut, Hex, Flanged, 3/8-16 14 1 19566MS Nut, Hex, Flanged, 5/8-11 34 1 19126 Nut, 1/4-20 15 1 19376 Bolt, Hex, 5/8-11 x 4” 35 1 25781 Weldment, Pan 16 1 25273 Weldment, Swing Handle 36 2 25664 Bushing, 0.75 OD x 0.507 ID x 0.5 17 3 19380 Bolt, Hex, 5/8-11 x 4-1/2” 37 1 25251 Weldment, Stand 18 2 19663 Nut, Square, 5/8-11 38 1 23684 Cover 19 2 19575 Bolt, Hex, Flanged, 1/2-13 x 1-1/2” 39 1 19554 Roller, Idler Assembly 20 4 19595 Nut, Hex, Flanged, 1/2-13 64 21258 14.2.2 Collection Chute Detail 12 11 8 7 9 10 13 12 13 6 5 4 14 3 15 2 16 1 Item Qty. Part No. 1 2 25242 Seal, Hopper Retainer, Side Description Item Qty. Part No. 10 3 19328 Description 2 1 25240 Retainer, Hopper, Rubber 11 1 25844 Holder, Brush Assembly 3 1 25787 Plate, Left Cap 12 24 19568 Bolt, Hex, Flanged, 5/16-18 x 3/4” 4 3 19347 Locknut, Nylon, 3/8-16 13 1 26032 Weldment, Hopper Loop 5 1 25277 Weldment, Hopper Lever Lock Collar 14 1 25786 Plate, Right Cap 6 1 19284 Pin, Spring, 3/16 x 1-1/8” 15 1 25672 Plate, Hopper Cap (Rear) 7 2 19447 Grip, Handle 16 1 25240 Seal, Rubber, Hopper 8 1 25290 Lever, Hopper 17 1 25660 Cover (Ns) 9 1 19177 Pin, Slotted Spring Bolt, Hex, 3/8-16 x 2 65 14.2.3 Tube Detail 1 2 3 4 5 6 7 8 14 12 7 13 11 1 10 1 9 Item Qty. Part No. 1 18 19577 Bolt, Hex, Flanged, 3/8-16 x 3/4 Description 2 1 17707 Coupler, Quick (Female) 4050-15P 3 1 17708 Coupler, Quick (Male) 8010-15P 4 1 36209 Weldment, Conveyor Tube 5 2 25666 Plate, Lock, Stainless 6 10 19315 Bolt, Carriage, 5/16-18 x 3/4 7 12 19318 Nut, Hex, Flanged, 5/16-18 8 8 19569 Bolt, Hex, Flanged, 3/8-16 x 1” 9 1 23815 Guard, Belt 10 1 30469 Weldment, Rocker Pin 11 4 19325 Bolt, Hex, 3/8-16 x 1” 12 2 25696 Pin, Hammerstrap, 1 x 3-3/4” 13 4 19564 Nut, Hex, Flanged, 3/8-16 14 1 23618 Guard, Belt 66 14.2.4 Discharge Detail 5 6 4 25 24 23 21 9 3 13 21 16 14 22 17 18 19 15 20 2 1 11 10 12 9 7 8 14 19 18 17 15 12 28 4 27 26 Item Qty. Part No. Description Item Qty. Part No. 1 1 25827 Weldment, Discharge Hood Transition 15 42 19318 Nut, Hex, Flanged, 5/16-18 Description 2 2 21257 Latch, Over-Center 16 1 25839 Plate, Bearing Spacer 3 4 19548 Rivet, 1/8” 17 4 27040 Housing, Roller Bearing 4 24 19568 Bolt, Hex, Flanged, 5/16-18 x 3/4” 18 4 21258 Bearing 5 1 25829 Weldment, Discharge Hood 19 4 21258-00c 6 1 18188 Light, Work (Optional) 20 18 19564 Nut, Hex, Flanged, 3/8-16 7 1 25278 Plate, Discharge Roller Slide 21 2 19249 Coupler, Lovejoy 8 1 25838 Plate, Transition Seal 22 1 19291 Coupling, Red Spider 9 4 19695 Bolt, Carriage, 3/8-16 x 1-1/4” 23 4 19595 Nut, Hex, Flanged, 1/2-13 Bearing, Collar 10 1 19533 Roller, Drive Assembly 24 1 19768 Motor, Hydraulic 4.5 cubic inch 11 2 25810 Brush, 5-1/4” 25 2 19355 Cap Screw, 1/2-13 x 1-1/2” 12 4 19382 Nut, Hex, 5/8-11 26 1 25799 Plate, Discharge Bottom 13 2 25809 Retainer, Brush 27 1 25805 Weldment, Discharge Transition 14 8 19310 Bolt, Hex, 5/16-18 x 1” 28 3 19380 Bolt, Hex, 5/8-11 x 4-1/2” 67 14.3 LADDER, SLIDE GATE, VIEW PORT, AND SAMPLE GATE L3 L8 L1 L7 L6 DETAIL C 3 L8 L4 L5 C L3 L2 L9 2 1 5 10 9 4 5 6 8 7 11 12 18 13 17 14 68 15 16 10 Item Qty. Part No. Description 1 24 19564 Nut, Hex, Flanged, 3/8-16 2 9 19577 Bolt, Hex, Flanged, 3/8-16 x 3/4 3 1 25899 Ladder Assembly L1 1 25673 Ladder, Top Assembly L2 1 25674 Ladder, Swing Assembly L3 8 19063 Plug, 1" Tube L4 2 19325 Bolt, Hex, 3/8-16 x 1 L5 2 19347 Locknut, 3/8-16 Nylon L6 1 19064 Shock, 120 Lb. Gas Spring Assist L7 1 19138 Cable, Self Gripping Velcro L8 2 19318 Nut, Hex, Flanged, 5/16-18 L9 2 19067 Pad, Rubber 4 1 25793 Insert, Slide Gate UHMW 5 2 25794 Slide, Gate 6 6 19348 Washer, Flat, 3/8 7 2 19335 Bolt, Carriage, 3/8-16 x 1-1/2 8 4 19334 Bolt, Carriage, 3/8-16 x 1 9 2 19149 Cylinder, Gate 10 7 19347 Locknut, Nylon, 3/8-16 11 4 47008 View Glass, S.S. Ring Assembly 12 12 19129 Rivet, 3/16 x 1/2 13 2 36150 Gate, Sample 14 2 25279 Retainer, Gate Skirt Side 15 4 19699 Screw, Self Drilling, 8-32 x 1/2 16 1 25276 Retainer, Gate Skirt 17 1 25662 Skirt, Gate 18 10 19779 Screw, Self Drilling, Zinc, 8-18 x 3/4 69 14.4 AXLE/WHEEL DETAIL 12 6 5 1 2 6 5 4 3 10 Item Qty. Part No. 11 Description 1 2 40145 Fender Assembly, Triple Axle 2 3 18193 Axle, 7000 lbs. 3 6 18131 ST235/80R16 4 8 19388 Bolt, Hex, 3/4-10 x 2 5 12 19396 Washer, Helical Spring Lock, 3/4 6 12 19394 Nut, Hex, 3/4-10 7 2 19133 Bumper, Rubber 8 2 19560 Bolt, Hex, 1/4-20 X 3/4 9 2 19126 Nut, Hex, Flanged, 1/4-20 10 2 19274 Flap, Mud 11 8 18482 Screw, Hex, Self-Tap 10-24 x 1/2 12 4 19650 BOLT, HEX, 3/4-10 X 4-1/2 13 2 23873 Plate, Hitch (NS) 14 1 14048 Wire Harness Fender 2012 (NS) * (NS) Not Shown Note: Quantities shown are for the triple axle model. 70 7 8 9 14.5 HYDRAULIC POWER SYSTEM 14.5.1 Engine And Hydraulic Pump 17 3 2 7 10 11 8 12 13 9 1 25 14 15 16 A 4 5 6 19 20 21 22 23 18 DETAIL A 24 Item Qty. Part No. Item Qty. Part No. 1 6 19597 Screw, Self Drilling,1/4-14 x 3/4 Description 14 1 18658 Cable, Battery, Set (33-1/2) Description 2 1 26119 Trim, Edge (10-5/8) 15 1 21286 Battery, SP-30 3 1 21270 Honda G340 (w/o Ignition Switch) 16 1 21319 Strap, Rubber Bungee (6”) 4 4 19328 Bolt, Hex, 3/8-16 x 2 17 1 19294 Tank Assembly, Hydraulic, 10 Gallon 5 6 19347 Locknut, Nylon, 3/8-16 18 10 19569 Bolt, Hex, Flanged, 3/8-16 x 1 6 6 19348 Washer, Flat, 3/8 19 1 19289 Housing, Bell 7 1 26120 Trim, Edge (27-5/16) 20 1 19247 Coupling w/ Setscrew, Engine Side 8 1 23838 Plate, Motor Guard 21 1 19290 Coupler, Spider, Black 9 1 26115 Cover, Manifold, Plastic 22 1 19248 Coupling w/ Setscrew, Pump Side 10 1 19165 Valve, Manifold 23 1 19295 Pump, Hydraulic 11 12 19568 Bolt, Hex, Flanged, 5/16-18 x 3/4 24 2 18577 Capscrew, Socket Head 12 4 19325 Bolt, Hex, 3/8-16 x 1-3/4 25 1 18006 Plug, Drain 13 24 19564 Nut, Hex, Flanged, 3/8-16 71 14.5.2 Hydraulic Hoses And Fittings 7 1 2 3 4 G H 6 8 M N 7 5 C D 6 7 14 15 A B C D 29 10 E F M 11 N 17 12 5 K I G 9 J H L 16 13 12 13 I 8 J 18 L 19 16 27 20 31 28 B A F K 29 17 E 21 24 26 25 72 23 22 30 15 Item Qty. Part No. Description 1 2 19355 Bolt, Hex 2 2 19595 Nut, Hex, Flanged, 1/2-13 3 1 19768 Motor, Hydraulic 4 2 17999 5 2 32338 Hose, Hydraulic 6 2 19149 Cylinder, Gate 7 4 18284 O-ring, Boss to 7/16-20 SAE 37° 8 2 32331 Hose, Hydraulic Valve to Gate, 1-1/4” 9 1 17707 Coupler, Quick (Female) 4050-15P 10 1 17708 Coupler, Quick (Male) 8010-15P 11 2 17623 O-ring, Boss to 3/4-16 SAE 37° 12 1 32335 Hose, Conveyor Motor Pressure ,1/2” Dia. 13 1 32336 Hose, Conveyor Motor Return, 1/2” Dia. 14 2 32332 Hose, Valve to Gate, 2-1/4” Dia. 15 2 32329 Hose, Raise and Lower, 1/4” Dia. 16 1 32333 Hose, Valve T-port to Return Filter, 3/4” Dia. 17 2 32334 Hose, Pump Pressure, 1/2” Dia. 18 1 5404-16-12 19 1 17133 Adapter, Elbow, 3/4 NPT to 1‑1/16-12 SAE 37° 20 1 19294 Tank, 10 Gallon Hydraulic Assembly 21 1 17754 Elbow, Adapter, 1 NPT to 1-5/16-12 SAE 37° 22 1 CP-752-10 23 1 32330 Hose, Tank to Pump, 1” Dia. Adapter, 1-1/16-12 Male SAE O-ring Boss to 1-1/16-12 Male SAE 37° Filter, 10 Micron Oil 24 1 18285 25 1 19295 Pump, Hydraulic 1 18292 Adapter, Elbow 7/8-14 Male SAE O-ring Boss (Long) to 7/8-14 Male SAE 37° 27 1 18578 Motor, 28.3 cubic inch, Pivot Plate 28 2 17699 Adapter, 1/2-14 Male BSPP to 7/16-20 SAE 29 2 32328 Hose, Valve to Rotate Motor 1/4” Dia. 30 2 17720 Adapter, 7/16-20 SAE O-ring Boss to 7/16-20 SAE 37° 31 1 17718 Cylinder, 3-1/2” Bore x 1.2 Stroke x 1-3/4” Rod 26 73 14.5.3 Hydraulic Manifold 8 7 9 6 10 1 3 4 13 5 14 2 11 1 12 Item Qty. 1 1 C12133 Part No. Body, Five Function Seed Tender Description 2 1 6400-12-12 Fitting, Straight, -12 MJIC x -12 MORB 3 2 6400-08-08 Fitting, Straight, -8 MJIC x -8 MORB 4 1 4500210 Orifice Check Disc, 0.037 5 8 6400-04-06 Fitting, Straight, -6 MJIC x -6 MORB 6 8 SV9-8-A-0-00 300AA00061A C11374 Cartridge, Solenoid Coil, P Series 12 Vdc Deutsch Spacer, Coil 7 1 RV1-10-I-0-30/24 Cartridge, Relief Valve 2400 PSI 8 1 RV1-10-I-0-30/26 Cartridge, Relief Valve 2600 PSI 9 1 PCS4-10-0-80 Cartridge, Pressure Compensator 80 PSI 10 1 ESV1-10-C-0-00 Prop. Poppet Valve Normally Closed Cartridge, Prioirty Flow, 1.25 GPM 11 1 PFR1-10-F-0-/1.25 12 1 RDH042S30 Cartridge, Relief Valve 100-3000 PSI 13 1 4500220 Orifice Check Disc, 0.046 14 1 PFR1-10-F-0-/0.50 Cartridge, Prioirty Flow, 0.50 GPM 74 14.6 WEIGH SYSTEM 2 1 13 13 3 18 12 11 17 16 14 20 15 9 8 7 6 9 5 10 19 4 21 Item Qty. Part No. Description Item Qty. Part No. Description 1 1 21257 Latch Assembly 12 4 17769 Bolt, Hex, Flanged, 1/4-20 x 0.75 2 1 23929 Enclosure Box 13 12 19129 Rivet, 3/16” x 1/2” 3 1 23930 Enclosure Box Lid 14 8 19795 Pin, Cotter 1/8 x 1 Square Cut Type 4 1 17610 Transmitter, Solid State 3A2222a 15 8 18641 Pin, 3/8” x 3” Headed 5 1 17612 Solid State Control Box 3B2223a2a 16 4 30458 Mount, Load Cell 6 2 17625 Hinge 17 4 13147 Bar, Load Cell 7 14 18941 Screw, Machine, Pan Head, #10 18 16 18943 Bolt, Hex, Flanged, 1/2-13 x 1.25 8 14 17722 Nut, #10-32 Nylon 19 16 19595 Nut, Hex, Flanged, 1/2-13 9 7 19564 Nut, Hex, Flanged, 3/8-1 6 20 1 30449 Weldment, Main Body 10 1 24689 Weldment, Enclosure Mount 21 1 30454 Weldment, Undercarriage 11 4 19126 Nut, Hex, Flanged, 1/4-20 75 14.7 DECALS AND LIGHTING 1 2 2 3 11 10 9 4 5 6 6 5 4 8 7 12 17 12 2 11 29 28 17 9 1 27 18 26 13 14 15 16 25 9 12 15 19 3 21 17 24 76 23 22 20 Item Qty. Part No. Description 1 2 20089 Decal, Gradient 2 2 18151 Light, Amber Clearance 3 2 15054 Decal, 400 SLD 4 2 15056 Decal, Gate Pinch Point 5 1 19052 Decal, Gate 1 6 1 19053 Decal, Gate 2 7 1 20088 Decal, Warning Hot Surface 8 1 18188 Light, Work 9 2 20087 Decal, Pinch Point Hand 10 1 19939 Decal, Falling Hazard 11 4 20082 Decal, Meridian 12 1 26095 Kit, Agri Cover Tarp 13 1 17730 Manual, 400 SLD Owners 14 1 18128 Tube, Storage 15 3 19309 Bolt, Hex, 5/16-18 x 3/4 16 5 19318 Nut, Hex, Flanged, 5/16-18 17 5 18229 Light, Red Clearance 18 1 19934 Decal, Caution Read Manual 19 6 19568 Bolt, Hex, Flanged, 5/16-18 x 3/4 20 1 19984 Decal, Serial Number 21 2 18117 Light, Tail 22 3 18096 Tape, Reflective, Meridian 2x6x6 23 2 19111 Plug, 6” x 2” Tube (0.188” Wall) 24 4 18420 Plug, 5” X 3” Tube (0.188” Wall) 25 1 17509 Decal, Warning, Crush/Electrocution Hazard 26 1 15055 Decal, Instruction, Release Conveyor 27 1 15057 Decal, Instruction, Capture Conveyor 28 3 14069 Sleeve, Tarp Stop Flat (FS627) 29 2 20090 Decal, Gradient 30 1 14044 Harness, Clearance Light (NS) 31 1 14046 Harness, Work Light (NS) 32 1 14067 Harness, Undercarriage Wire (NS) 77 14.8 TURRET DETAIL 11 12 10 9 8 13 7 6 5 14 A 3 4 15 2 1 DETAIL A 16 17 18 22 19 20 21 Item Qty. Part No. Item Qty. Part No. 1 4 19126 Nut, Hex, Flanged, 1/4-20 Description 15 1 30461 Pin, Cylinder 2 4 19114 Screw, Countersunk Cap 1/4-20 x 1 16 5 19569 Bolt, Hex, Flanged, 3/8-16 x 1 3 2 25849 Pad, Wear, Extend Arm 17 1 23901 Plate, Reinforcement 4 1 18164 Jack, 5K, 10” Stroke Top Wind 18 1 30459 Receiver, Conveyor Hitch 5 1 14002 Switch 19 12 19568 Bolt, Hex, Flanged, 5/16-18 x 3/4 6 1 30468 Pin, Lock 20 10 19318 Nut, Hex, Flanged, 5/16-18 7 1 30453 Weldment, Conveyor Arm Bottom 21 2 19624 Latch, Horizontal 8 1 36031 Weldment, Conveyor Arm Top 22 1 30452 Weldment, Conveyor Pivot Plate 9 3 18476 Bolt, Hex, 3/4-10 x 1-1/2 10 1 23757 Plate, Retainer, Swivel, Conveyor 11 1 17758 Bushing 12 1 12582 Pin, Clevis 1 x 4-45/64 Eff. Length 13 1 19794 Pin, Lynch 3/16 x 1 14 1 17718 Cylinder 78 Description 14.9 BUMPER HITCH DETAIL 6 1 5 3 Item Qty. Part No. 2 4 Description 1 2 19911 Decal, White, Meridian Trailer 2 24 19116 Bolt, Hex, 1/2-13 x 1-1/2” long Grade 8 3 24 19373 Washer, Lock, 1/2" 4 24 19115 Nut, Hex, 1/2-13, Grade 8 5 21 18096 Tape, Reflective, Meridian 2 x 6 x 6” 6 1 25851 Weldment, Bumper Hitch 7 1 14047 Wire Harness, Tongue (NS) 8 1 18192 Mount, Jack Stand A-Frame (NS) 9 1 19298 Coupler, Hitch 2-5/16 Adjustable (NS) 10 1 19275 Breakaway, Battery (NS) * (NS) Not Shown 79 14.10 GOOSENECK DETAIL 10 11 12 9 3 1 8 14 16 15 4 6 5 4 13 15 16 6 17 2 Item Qty. Part No. Description 1 2 19911 Decal, White, Meridian Trailer 2 1 18197 Crank, Handle, Gooseneck Jack 3 1 25325 Extension, Handle, Gooseneck Jack 4 28 19116 Bolt, Hex, 1/2-13 x 1-1/2” Grade 8 5 28 19373 Washer, Lock, 1/2” 6 28 19115 Nut, Hex 1/2-13, Grade 8 7 1 14043 Wire Harness, Tongue (NS) 8 26 18096 Tape, Reflective, Meridian 2 x 6 x 6 9 1 25336 Weldment, Gooseneck 10 1 19275 Breakaway, Battery BA10-150 11 3 19779 Screw, Self Drilling, #8-18 x 3/4 12 1 19597 Screw, Self Drilling 1/4-14 x 3/4 13 1 25322 Weldment, Jack, Gooseneck - 12k 14 1 19626 Bolt, Hex, Flanged, 3/8-16 x 1-3/4 15 2 19347 Locknut, nylon, 3/8-16 16 3 19348 Washer, Flat, 3/8 17 1 19592 Bolt, Hex, 3/8-16 x 2-1/2 80 5 NOTES 81 NOTES 82 MERIDIAN MANUFACTURING INC. With over 65 years of experience, Meridian is your storage and handling expert. Cambridge Office 605 Sheldon Drive Cambridge, ON N1T 2K1 PH: 519.620.6004 TF: 855.346.3712 FX: 519.620.6041 Camrose Office 4232 - 38 St. Camrose, AB T4V 4B2 PH: 780.672.4516 TF: 800.830.2467 FX: 780.672.4759 Regina Office PO Box 1996 Regina, SK S4P 3E1 PH: 306.545.4044 TF: 800.667.5904 FX: 306.545.4216 Storm Lake Office 2902 Expansion Blvd. Storm Lake, IA 50588 PH: 712.732.1780 TF: 800.437.2334 FX: 712.732.1028 Lethbridge Office 3125 - 24 Ave. N. Lethbridge, AB T1H 5G2 PH: 403.320.7070 TF: 800.661.1436 FX: 403.320.7579 Winkler Office Box 760, 275 Hespler Ave. Winkler, MB R6W 4A8 PH: 204.325.7883 TF: 800.665.7259 FX: 204.325.5556 © 2014 Meridian Manufacturing Inc. Registered Trademarks Used Under License. 84 Form No. 17730 Printed In U.S.A. (03-2014)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Meridian Manufacturing Inc. Create Date : 2015:12:15 10:42:53-06:00 Modify Date : 2016:04:22 14:59:43-06:00 XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Metadata Date : 2016:04:22 14:59:43-06:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:357ae3a5-1c18-41e3-954f-651ec46e72b9 Original Document ID : xmp.did:0380117407206811AB08BD934DD0E129 Document ID : xmp.id:12e75c2c-e238-a548-9534-44755a11f59a Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:bcd075a7-9541-264c-964f-7188dd55205e Derived From Document ID : xmp.did:BB71E39FC18DE311A3FBFBADCE3D3F9C Derived From Original Document ID: xmp.did:0380117407206811AB08BD934DD0E129 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2015:12:15 10:42:53-06:00 Format : application/pdf Title : 2016 Meridian 400SLD Bulk Seed Tender operators Manual Description : Operators Manual Creator : Meridian Manufacturing Inc. Subject : Producer : Adobe PDF Library 15.0 Trapped : False Keywords : .. Page Count : 84EXIF Metadata provided by EXIF.tools