IB(NA) 66522 C Mitsubishi Freqrol FR A024 Manual

• SAFETY PRECAUTIONS
• SETTING MEMO
• SAFETY INSTRUCTIONS
• CONTENTS
• GUIDELINES FOR HANDLING
• 1. PRECAUTIONS
• 2. NOMENCLATURE AND FUNCTIONS
• 3. PREPARATION BEFORE OPERATION
• 4. OPERATION CONTROL MODES
• 5. INSTALLATION
• 6. WIRING
  • 6.1 Precautions
  • 6.2 Connecting the Power Supply and Motor
  • 6.3 Connecting the Control Signals
  • 6.4 Operating the Inverter Using Single-Power Supply
  • 6.5 Wiring procedures
• 7. SETTlNG PARAMETERS BEFORE STARTUP
• 8. NOMENCLATURE OF PARAMETER UNIT
• 9. PRECAUTIONS ON OPERATING THE PARAMETER UNIT
• 10. OUTLINE OF THE FUNCTIONS
• 11. OPERATION
  • 11.1 Operation Modes
  • 11.2 Selecting the Operation Mode
  • 11.3 External Operation Mode (Operation Using External input Signals)
  • 11.4 PU Operation Mode (Operation Using the Parameter Unit)
  • 11.5 Combination Operation Mode (Operation Using both External Signals and Parameter Unit)
  • 11.6 Switch over mode
  • 11.7 Edit Enable Signal Mode
  • 11.8 Local/Auto External Signal Selection Mode
• 12. SETTING AND CHANGING THE PARAMETERS
• 13. INITIALIZING THE PARAMETERS
  • 13.1 Parameter Clear
  • 13.2 Parameter All Clear
• 14. MONITORING
• 15. ERRORS
  • 15.1 Error Codes and Contents of Errors
  • 15.2 Digital Display (7-Segment Display) and Actual Characters
  • 15.3 Logged Error Contents
  • 15.4 Clearing Error Log
• 16. PARAMETER UNIT DISCONNECTION DETECTION FUNCTION
• 17. RESETTING THE INVERTER
• 18. CALIBRATING THE FREQUENCY METER
• 19. ADJUSTING "BlAS" AND "GAIN" OF FREQUENCY SETTING SIGNALS
• 20. CONTROLLING KEY CLICK SOUND (TACTILE FEED BACK)
• 21. SELECTING GENERAL-PURPOSE MAGNETIC FLUX VECTOR CONTROL
• 22. PARAMETERS
  • Parameter List
  • Description of the Parameters
  • Pr.0: Setting the torque boost (manual)
  • Pr.1, Pr2: Setting the upper/lower limit of frequency
  • Pr.3: Setting the base frequency
  • Pr.4, Pr5, Pr6: setting the multiple-speed
  • Pr.7, Pr.8: Setting the acceleration/deceleration time
  • Pr.9: Setting the electronic thermal relay
  • Pr.10, Pr.11, Pr.12: Adjusting the DC Injection braking
  • Pr.13: Setting the starting frequency
  • Pr.14: Selecting the applied load
  • Pr.15, Pr.16: Setting the Jog operation
  • Pr.17: Setting the thermal relay input
  • Pr.18: Setting the upper limit frequency for high speed operation
  • Pr.22, Pr.23, Pr.66: Setting the stall prevention function operation level
  • Pr.29: Selecting the acceleration/deceleration pattern
  • Pr.30, Pr.70: Setting the regenerative brake duty ratio
  • Pr.31, Pr.32, Pr.33, Pr.34, Pr.35, Pr.36: Serial communication functions
  • Pr.37: Setting the speed display unit
  • Pr.38: Frequency at 5V (10V) input
  • Pr.39: Frequency at 20mA input
  • Pr.40: Sestting the allocation of output terminals
  • Pr.41: Adjusting the SU frequency bandwidth
  • Pr.42, Pr43: Setting the sensing for output frequency
  • Pr.44, Pr.45, Pr.46, Pr.47: Setting the second control functions
  • Pr.54: Selecting the FM terminal function
  • Pr.55 Reference for frequency monitor
  • Pr.56: Reference for current monitor
  • Pr.57, Pr.58: Operation restart after instantaneous power failure
  • Pr.59: Input terminal allocation
  • Pr.60: Input filter time constant
  • Pr.61: Tone control selection
  • Pr.62, Pr.63: Open motor circuit detection function
  • Pr.64, Pr76, Pr.81: Slip compensation
  • Pr65: Selection o retry
  • Pr.67, Pr68, Pr.69: Retry function
  • Pr.70: Refer to Pr.30
  • Pr.71: Selecting the applicable motor
  • Pr.72: Changing the PWM carrier frequency
  • Pr.73: Selecting the frequency command voltage range
  • Pr.74: Selecting the current input signal/Starting command - rotation direction command selection
  • Pr.75: Reset selection/detection of parameter unit disconnection
  • Pr.77: Disabling parameter write
  • Pr.78: Reverse lockout
  • Pr.79: Selecting the operation mode
  • Pr.80: Capacity of applicable motor (for general-purpose magnetic flux vector control)
  • Pr.91, Pr.92, Pr.93, Pr.94, Pr.95, Pr.96: Frequency jump
  • Pr.900: Calibrating the output at terminal FM
  • Pr.902, Pr.903, Pr.904, Pr.905: Adjusting the gain and bias for the frequency setting signal
  • Pr.990: Selecting key click sound (parameter unit)
  • Pr.991: Selection of the parameter unit display data
  • Pr.996: Clearing the alarm
  • Pr.997: Resetting the inverter
  • Pr.998, Pr.999: Initializing the parameters
• 23. INSPECTION AND MAINTENANCE
  • 23.1 Precautions on Inspection and Maintenance
  • 23.2 Inspection items
  • 23.3 Replacing Parts
  • 23.4 Measuring Voltage, Current, and Power in Main Circuit
• 24. TROUBLESHOOTING
  • 24.1 Inspection by the Display on the Parameter Unit
  • 24.2 Troubles and Check Points
  • 24.3 Protection Functions
  • 24.4 Noise
  • 24.5 Power harmonic guidelines (Japan)
• 25. SPECIFICATIONS
  • 25.1 Standard Specifications
  • 25.2 Common Specifications
  • 25.3 Block Diagram
  • 25.4 Definition of Terminals
  • 25.5 External Dimensions
• 26. SELECTION OF PERIPHERAL DEVICE
• 27. OPTION
• APPENDICES
  • Appendix 1. INSTRUCTIONS FOR COMPLIANCE WITH THE EUROPEAN DIRECTIVES (LVD compliant product has CE marking.)
  • Appendix 2. INSTRUCTIONS FOR COMPLIANCE WITH THE UL STANDARD (UL listed product has UL marking.)
  • Appendix 3. WARRANTY
• Revisions