128 A0 11 EN !! SF20220RSandfilterpump

Preview ! SF20220RSandfilterpump Leapfrog Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

User Manual: !! Leapfrog Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Open the PDF directly: View PDF .
Page Count: 30

Download
Open PDF In Browser	View PDF

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

OWNER’S MANUAL

English

128

IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.

Sand Filter Pump
Model SF20220R

For illustrative purposes only.

Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.

©2010 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands

128**-A0-1108

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

TABLE OF CONTENTS

English

Warnings.......................................................................... 3
Parts List & References.................................................. 4-8
Setup Instructions ......................................................... 9-17
Product Specifications................................................... 11
Operating Instructions ................................................... 18-20
Intex Pools Operating Time Table.................................. 21-22
Non-Intex Pools Operating Time Table.......................... 23
Maintenance.................................................................... 24-25
Long Term Storage.......................................................... 25
Troubleshooting Guide................................................... 26
Common Pool Problems................................................. 27
General Aquatic Safety................................................... 28
Limited Warranty............................................................. 29
Intex Service Center Locations..................................... 30

SAVE THESE INSTRUCTIONS

Page 2

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SAFETY RULES

English

IMPORTANT SAFETY RULES

Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.

READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They must
at all times be supervised by a knowledgeable and experienced adult responsible for their
safety.
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect this product only to a grounding type receptacle protected
by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a
qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD.
Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).
• Always unplug this product from the electrical outlet before removing, cleaning, servicing
or making any adjustment to the product.
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn
mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or
converter plugs to connect unit to electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your
hands are wet.
• Keep this product more than 2m away from the pool.
• Keep this product more than 3.5m away from the pool (for France only).
• Keep the plug of this product more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on it and
accessing the pool.
• Do not operate this product when pool is occupied.
• This product is for use with storable pools only. Do not use with permanently installed
pools. A storable pool is constructed so that it may be readily disassembled for storage
and reassembled to its original configuration.
• To reduce the risk of entrapment hazard, never enter the pool if suction strainer
component is loose, broken, cracked, damaged or missing. Replace loose, broken,
damaged, cracked or missing suction strainer components immediately.
• Never play or swim near suction fittings. Your body or hair may be trapped causing
permanent injury or drowning.
• To prevent equipment damage and risk of injury, always turn pump off before changing
the filter control valve position.
• Never operate this product above the maximum working pressure stated on the filter tank.
• Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to
blow off and cause serious injury, property damage or death.
• This product is intended to be used only for the purposes described in the manual!

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.

SAVE THESE INSTRUCTIONS

Page 3

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PARTS LI ST

English

PARTS LIST
1

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

SAVE THESE INSTRUCTIONS

Page 4

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PARTS LI ST

English

PARTS LIST (continued)
19

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

SAVE THESE INSTRUCTIONS

Page 5

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PARTS REFERENCE

English

PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.

31
32
10
1
2

9
11
8

12
4

13
14

5
15
16
17

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

SAVE THESE INSTRUCTIONS

Page 6

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PARTS REFERENCE

English

PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

SAVE THESE INSTRUCTIONS

Page 7

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PARTS REFERENCE

English

PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
REF. NO.

DESCRIPTION

QTY.

SPARE PART NO.

PRESSURE GAUGE

11224

DRAIN OUTLET COVER

11131

CENTER PIPE

11268

TANK O-RING

11225

FILTER GRID

11269

DRAIN VALVE CAP

11226

DRAIN VALVE O-RING

11227

CLAMP BOLT

11262

L-SHAPE O-RING

11228

HOSE WITH NUTS

11010

SAND FILTER INTERCONNECTING HOSE

11229

WRENCH

11231

LEAF TRAP COVER

11259

LEAF TRAP O-RING

11232

BASKET

11260

FILTER HOUSING NUT

11261

O-RING A

10712

SEDIMENT RELEASE VALVE

10460

VALVE O-RING

10264

PLUNGER VALVE (HOSE O-RING & STEP
WASHER INCLUDED)

10747

HOSE O-RING

STEP WASHER

STRAINER NUT

10256

FLAT STRAINER RUBBER WASHER

10255

THREADED STRAINER CONNECTOR

11235

10262
10745

ADJUSTABLE POOL INLET NOZZLE

11074

ADAPTOR B

10722

STRAINER CONNECTOR

11070

POOL INLET NOZZLE

11071

STRAINER GRID

11072

6-WAY VALVE DIVERTER

11324

6-WAY VALVE SET

11321

PUMP MOTOR & CONTROL

11322

PRE-FILTER ASSEMBLY

11371

When ordering parts, be sure to quote the model number and part numbers.

SAVE THESE INSTRUCTIONS

Page 8

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:

1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (25) (see drawing 1).
Be careful not to lose the step rubber
washer (22). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (23) from the threaded
connector (25). Leave the flat washer (24)
on the connector (25).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector (25) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut (23) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (23) back onto the threaded
connector (25) (see drawing 2).
5. Finger tighten the strainer nut (23) onto the
threaded connector (25).
6. Grasp the plunger valve assembly. Make
sure the step washer (22) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (25) (see drawing 3).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling (see
drawings 4.1 & 4.2).

INSIDE
LINER WALL

3
1

2
1
2

SAVE THESE INSTRUCTIONS

4.1
INSIDE
LINER
WALL

4.2

Page 9

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

POOL INLET - NOZZLE & PLUNGER VALVE SETUP
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (25) (see drawing 5).
Be careful not to lose the step rubber
washer (22). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (23) from the threaded
connector (25). Leave the flat washer (24)
on the connector (25).
3. Install the nozzle and plunger valve at the
upper position of pool inlet. From the inside
of the pool liner insert the connector (25)
into one of the pre-cut holes with the
washer remaining on the connector to be
placed against the inside of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut (23) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (23) back onto the threaded
connector (25) (see drawing 6).
5. Finger tighten the adjustable pool inlet
nozzle (26) and the strainer nut (23) onto
the threaded connector (25).
6. Grasp the plunger valve assembly. Make
sure the step washer (22) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (25) (see drawing 7).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling (see
drawings 8.1 & 8.2).
9. Adjust the direction of nozzle head pointing
away from the pool outlet for a better
circulation result (see drawing 9).
10. The pool liner is now ready to fill with
water. Consult the above-ground-pool
owner’s manual for filling instructions.

1
INSIDE
LINER WALL

7
1

2
8.1

INSIDE
LINER
WALL

8.2

9
WATER
FLOW

POOL

SAVE THESE INSTRUCTIONS

Page 10

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

PR O DU C T S P EC S & SE TU P IN S TR U CT IO N S

English

PRODUCT SPECIFICATIONS
The sand filter removes suspended particles and does not sanitize your pool.
Pool chemistry is a specialized area and you should consult your local pool
service specialist for details.
Power:
Wattage:
Maximum working pressure:
Effective filtering area:
Maximum Flow Rate:
Recommended filtering media:

220-240 Volt AC
650 W
3.5 bar (50 psi)
0.13 m2 (1.44 ft2)
10030 liters/hour (2650 gallons/hour)
Use only No. 20 silica sand. Particle size
range 0.45 to 0.85 mm (0.018 to 0.033
inches). Uniformity Coefficient less than 1.75.
Recommended filtering media quantity: 45 Kg (100 Lbs)
Limited Warranty:
2 Years (see “Limited Warranty”)

SETUP INSTRUCTIONS
Pump location and mounting:
• The system must be installed on a solid level and vibration-free base.
• Provide a location protected from the weather, moisture, flooding and
freezing temperature.
• Provide adequate access, space and lighting for routine maintenance.
• Pump motor requires free circulation of air for cooling. Do not install
the pump in a damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.

Motor pre-filtering assembly setup:
1. Remove the sand filter and its accessories from the packaging carefully and
inspect for any visible damage. If parts are damaged contact your local
service center listed at the back of this owner’s manual.
2. In a counter-clockwise motion unscrew the leaf trap cover (13) from the
pre-filter housing. Take out the basket (15) and filter housing nut (16) (see
drawing 10).
3. Connect the pre-filter housing to the motor water inlet. Note: Align the connector
in the pre-filter housing with the water inlet on the motor (see drawing 11).
10

SAVE THESE INSTRUCTIONS

Page 11

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SETUP INSTRUCTIONS (continued)
4. In a clockwise motion screw filter housing nut (16) onto the motor water inlet
(See drawings 12.1 & 12.2).
12.2

12.1

5. Replace the basket (15) and leaf trap cover (13) back to the pre-filter housing
(See drawings 13.1 & 13.2).
13.1

13.2

Sand tank installation:
1. Place the tank on the selected location.
2. Connect the motor pre-filtering assembly unit to the tank support base (See
drawing 14.1). NOTE: Ensure the pre-filter housing water inlet hose connection
is facing towards the pool.
IMPORTANT: Some countries, especially in the European community,
require the product to be secured to the ground or to a base in a
permanent upright position. Check your local authorities to determine if
there is a regulation in your area regarding above-the-ground swimming
pool filter-pumps. If yes, then the product can be mounted to a platform
using the two holes located in the base. See drawing 14.2.
The product can be mounted on a cement base or onto a wooden
platform to prevent accidental falling over.
• The mounting holes are 6.4 mm in diameter and spaced 117.4 mm
apart.
• Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
14.1

14.2

117.4 mm

SAVE THESE INSTRUCTIONS

Page 12

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SETUP INSTRUCTIONS (continued)
3. In a clockwise motion screw the center pipe (3) onto the filter grid (5) securely
by hand (see drawing 15).
4. Vertically insert the filter grid and center pipe assembly into the tank. Ensure
filter grid assembly is securely fitted to the bottom of the tank, and the center
pipe is vertically centered inside the tank (see drawing 16).
15

Sand loading:
IMPORTANT: Use only No. 20 silica sand with particle size range 0.45 to 0.85
mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.
NOTE: Before loading the tank with sand, ensure the sand filter grid and
center pipe assembly is securely in place on the tank bottom, and the
center pipe (3) is vertically centered inside the tank.
1. To prevent sand from falling into the center pipe top opening when pouring the
sand, cover the center pipe top opening with a cup or similar object (see
drawing 17).
2. With one person holding the center pipe to keep it centered, pour the sand into
the tank at a slow rate manually to prevent the filter grid assembly from shifting
(see drawing 18).
17

SAVE THESE INSTRUCTIONS

Page 13

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SETUP INSTRUCTIONS (continued)
3. Fill the tank approximately half way first to evenly distribute the sand inside the
tank, then fill the tank with some water to provide a cushioning effect when the
remaining sand is poured in. This prevents the filter grid (5) from excessive
shock (see drawing 19).
4. Sand shall be filled between the “MAX” and “MIN” marked gauge on the center
pipe. Evenly spread and level out the sand by hand (see drawings 19 & 20).
20

MAX

MIN

MAX

MIN

5. Remove the protective cup from the center pipe top opening.
6. Wash away all sand around the top edge of the tank.
IMPORTANT: Ensure the center pipe (3) remains centered after sand loading
is completed before proceeding to the next step.

6-way valve installation:
1. Place the tank o-ring (4) around the top edge of the tank groove (see
drawing 21). NOTE: Ensure the tank o-ring is free of sand or debris.
21

SAVE THESE INSTRUCTIONS

Page 14

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SETUP INSTRUCTIONS (continued)
2. Lower the 6-way valve cover over the tank slowly, and ensure the bypass pipe
protruding underneath the 6-way valve cover fits securely into the center
pipe (3) top opening (see drawing 22). Make sure the tank o-ring is securely
fitted between the top edge of the tank groove and the 6-way valve cover
edge.
IMPORTANT: There are three hose connection ports on the 6-way valve,
ensure the outlet connection (from filter to the pool) on the valve is facing
towards the pool, and the inlet connection (from motor to valve) is aligned
with the motor outlet (see drawing 23).
22

WATER
INLET

WATER
OUTLET

3. Place an L-shape o-ring (9) on the 6-way valve inlet connection and on the
pump motor outlet. In a clockwise motion connect the sand filter
interconnecting hose (11) between the pump motor outlet and the 6-way valve
inlet connection (see drawing 24).
4. Remove the clamp bolt cover and the clamp bolt (8), and install the flange
clamp around the tank and 6-way valve flanges (see drawing 25).
5. Insert the clamp bolt (8) into the pre-installed nut on the clamp, and securely
tighten it with the wrench (12) supplied. Replace the clamp bolt cover back.
(see drawings 26.1 & 26.2).
24

26.1

26.2

WARNING
Improper tank valve and clamp assembly could cause the valve and clamp
to blow off and cause serious injury, property damage or death.

SAVE THESE INSTRUCTIONS

Page 15

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SAND FILTER PUMP HOSE CONNECTION SETUP

WARNING
•
•
•
•

Keep this product more than 2m away from the pool.
Keep this product more than 3.5m away from the pool (for France only).
Keep the plug of this product more than 3.5m away from the pool.
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.

The 6-way valve has three hose connection ports.
1. Connect one hose (10) end to the pre-filter inlet and the other end of the hose
to the lower plunger valve with the strainer. Ensure the hose nuts are securely
tighten.
2. Connect the second hose (10) between the 6-way valve water outlet and the
upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely
tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be
directed to a proper draining receptacle using a hose or pipe (not provided).
Remove the drain cap before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.

WATER LEVEL

6-WAY VALVE
PLUNGER VALVE
WATER OUTLET
WATER
INLET

L-SHAPE
O-RING

ADJUSTABLE
POOL INLET
NOZZLE

WATER INLET

THREADED
STRAINER
CONNECTOR

TO
DRAIN

L-SHAPE
O-RING
POWER
CORD

MOTOR

MOTOR
WATER
OUTLET

OUTSIDE
LINER WALL

PREFILTER

>2M

>3.5M
(ILLUSTRATION NOT TO SCALE)

SAVE THESE INSTRUCTIONS

Page 16

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SETUP I NSTRUCTIONS

English

SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
For NON-INTEX pool:
Connect the hose (10) to the pool inlet/outlet connection with a large hose clamp.
Tighten securely. Remove the drain cap (2) before attaching the drain/waste
hose or pipe.
10

LARGE HOSE
CLAMP

2
POOL

>2M

>3.5M

For INTEX pool size 16' and below:
1. In a counter-clockwise motion unscrew plunger valve union from the threaded
strainer connector (25). Be careful not to lose the step rubber washer (22).
2. Grasp the plunger valve assembly. Make sure the step washer (22) is in place.
Connect adaptor B (27) to plunger valve union.
3. Remove wall plug and then insert the strainer (28 & 30) into the lower position
of protruding hose connection, and the nozzle (28 & 29) into the upper position
of protruding hose connection. Adaptor B (27) fits over the strainer
connection (28) inserted into the connection. Tighten securely.
4. Remove the drain cap (2) before attaching the drain/waste hose or pipe.

28 & 29
2
POOL
28 & 30

>2M

>3.5M

SAVE THESE INSTRUCTIONS

Page 17

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

OPERATI NG I NSTRUCTIONS

English

OPERATING INSTRUCTIONS

WARNING
• Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or
residual current device (RCD). Contact a qualified electrician if you cannot
verify that the receptacle is protected by a GFCI/RCD. Use a qualified
electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).
• To reduce the risk of electric shock, do not use extension cords, timers,
plug adaptors or converter plugs to connect unit to electric supply;
provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water
or when your hands are wet.
• Never operate this product above the maximum working pressure stated
on the filter tank.
• Always switch off pump before changing the 6-way valve position.
• Operating this product without water flowing through the system can
cause a build up of hazardous pressure which can result in an explosive
situation, serious injury, property damage or death.
• Never test this pump with compressed air. Never operate the system with
water temperature above 35° C (95° F).

6-way valve positions and function:
Valve Position
Function
Normal filtration and regular
FILTER
(see drawing 27) vacuuming of pool
BACKWASH Reverses water flow to clean
(see drawing 28) filter media
For initial startup cleaning of the sand, and
RINSE
(see drawing 29) leveling the sand bed after backwashing
For vacuuming directly to waste,
WASTE
(see drawing 30) lowering pool level or to drain the pool

Water Flow Direction
From pump through filter media
to pool
From pump through filter media
to valve waste/drain outlet
From pump through filter media
to valve waste/drain outlet
From pump to valve waste/drain
outlet bypassing the filter media

RECIRCULATE For circulating water back to pool

From pump through valve to
pool bypassing the filter media

(see drawing 31) without going through the filter media

Shuts off all flow to filter and pool

CLOSED

(see drawing 32) “Do not use this setting with pump running”

CK
WA
SH

WAST

ULATE

RECIRC

S
CLO

E
NS
RI

OS
CL

SAVE THESE INSTRUCTIONS

RECIRCULATE

NS
RI

29
FILT
ER
WASTE

FIL
T

WASTE

REC
IRC

NS
RI

BA
CK

Page 18

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

OPERATI NG I NSTRUCTIONS

English

OPERATING INSTRUCTIONS (continued)
30
NS E
RI

S
CLO

BA
CK
WA
SH

FILTE
R

S
CLO

TE
R

IRCULATE

AC
KW
ASH

WASTE

FILTE
R

WASTE

RECIR
CULATE

NS
RI

O
CL

Initial startup and operation:
Before operating, be sure that:
• All the hoses have been connected and tightened securely, and correct amount
of filter sand have been loaded.
• The entire system is connected to a grounding type receptacle protected by a
ground-fault circuit interrupter (GFCI) or residual current device (RCD).

CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, and explosive situation could exist.
1. Grasp a plunger valve handle. Turn the handle counter-clockwise, pull up until it
stops, and then turn it clockwise until the metal protruding notch anchor is in
the "0/1" position. Repeat for the second plunger valve. This opens the valves to
allow water to flow into the sand filter pump.
2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to
a proper draining receptacle.
3. Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH” position
(see drawings 28 & 33).
IMPORTANT: To prevent damage to the
6-way valve, always depress the valve
handle before turning. Always switch off
pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 34). Water
is circulating backward through the sand
media and to waste/drain outlet. Backwash
until a clear flow of water is observed in the
waste/drain outlet or through the drain sediment
window.
NOTE: The initial backwash of the filter is
recommended to remove any impurities or fine
sand particles in the sand media.

SAVE THESE INSTRUCTIONS

OFF TIMER

Page 19

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

OPERATI NG I NSTRUCTIONS

English

OPERATING INSTRUCTIONS (continued)
5. Switch off the pump, change the 6-way valve to “RINSE” position (see
drawing 29).
6. Switch on the pump and run the pump for about one minute to level out the
sand bed after backwashing the sand media.
7. Switch off the pump, change the 6-way valve to “FILTER” position (see
drawing 27).
8. Switch on the pump. The system is now operating in the normal filtering mode.
Run the pump until the desired pool water clearance is obtained and no more
than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash
frequently due to unusual heavy dirt present in the water and sand. After that,
as the filter removes dirt and impurities from the pool water, the accumulated
dirt in the sand media will cause the pressure to rise and the flow to diminish. If
there is no vacuuming device attached to the system and the pressure gauge
reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH” under “initial startup and operation” section.
Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also
cause the flow to diminish and the pressure to rise. Remove any vacuuming
device from the system and check if the pressure gauge reading has dropped
from the yellow zone to the green zone.

Operating the system under “TIMER” mode or manually:
To operate the sand filter pump in “FILTER” mode under “TIMER” control:
A. Set the timer dial to the desired operating hours. See operation time table
(see drawing 35).
B. Turn on the pump by pressing the switch to “ ” position, the sand filter
pump is now filtering the water and will stop after the operating hours are
completed. The built-in timer will now operate for the number of hours
selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the sand filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “-” position, the sand filter
pump is now filtering the water.
B. To turn off the pump, press the switch to “O” position.
35

TIMER DIAL
(HOURS)

OFF

TIMER

SAVE THESE INSTRUCTIONS

Page 20

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

English

128

INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)
This table shows the required operating time for average use of the sand filter pump with above
ground pools.

Pool Size

Sand filter
Water Capacity (Calculated at
pump operating
90% for Frame Pool and 80% for
time (For one
Easy Set & Oval Pool)
cycle)
(Gals)

(Liters)

(Hours)

18' x 42" (549cm x 107cm)

4786

18115

18' x 48" (549cm x 122cm)

5455

20647

18' x 52" (549cm x 132cm)

5894

22309

18' x 48" (549cm x 122cm)

6423

24311

18' x 52" (549cm x 132cm)

6981

26423

24' x 48" (732cm x 122cm)

11483

43462

24' x 52" (732cm x 132cm)

12481

47421

16' x 48" (488cm x 122cm)

5061

19156

18' x 52" (549cm x 132cm)

6981

26423

16'8" x 49" (508cm x 124cm)

5061

19156

18'8" x 53" (569cm x 135cm)

6981

26423

20' x 12' x 48" (610cm x 366cm x 122cm)

4393

16628

24' x 12' x 48" (732cm x 366cm x 122cm)

5407

20465

28' x 12' x 48" (853cm x 366cm x 122cm)

6420

24300

18' x 9' x 52" (549cm x 274cm x 132cm)

4545

17203

24' x 12' x 48" (732cm x 366cm x 122cm)

7757

29359

24' x 12' x 52" (732cm x 366cm x 132cm)

8403

31805

32' x 16' x 52" (975cm x 488cm x 132cm)

14364

54368

INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL

ROUND
METAL
FRAME POOL

ULTRA FRAME
POOL
SEQUOIA SPIRIT®
POOL SET

OVAL FRAME
POOL

RECT. ULTRA
FRAME POOL

SAVE THESE INSTRUCTIONS

Page 21

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

English

128

INTEX POOLS OPERATING TIME TABLE (WITH INTEX SALTWATER SYSTEM)
If the system is attached to an “Intex Saltwater System” unit, the filter pump running time
should be longer than the required operating time of the Intex Saltwater System unit.

Pool Size

Saltwater System
Water Capacity (Calculated at
Sand Filter
operating Time (with
90% for Frame Pool and 80%
Pump
cyanuric acid 30-50ppm) (hours) Operating
for Easy Set & Oval Pool)
Time
10 - 19°C 20 - 28°C 29 - 36°C
(Gals)
(Liters)
(50 - 66°F) (68 - 82°F) (84 - 97°F) (hours)

INTEX ABOVE GROUND POOLS (AGP’s)

EASY SET®
POOL

CIRCULAR
METAL
FRAME POOL

15' x 33" (457cm x 84cm)

2587

9792

15' x 36" (457cm x 91cm)

2822

10681

15' x 42" (457cm x 107cm)

3284

12430

15' x 48" (457cm x 122cm)

3736

14141

16' x 42" (488cm x 107cm)

3754

14209

16' x 48" (488cm x 122cm)

4273

16173

18' x 42" (549cm x 107cm)

4786

18115

18' x 48" (549cm x 122cm)

5455

20647

18' x 52" (549cm x 132cm)

5894

22309

15' x 36" (457cm x 91cm)

3282

12422

15' x 42" (457cm x 107cm)

3861

14614

15' x 48" (457cm x 122cm)

4440

16805

16' x 48" (488cm x 122cm)

5061

19156

18' x 48" (549cm x 122cm)

6423

24311

18' x 52" (549cm x 132cm)

6981

26423

20' x 52" (610cm x 132cm)

8638

32695

24' x 48" (732cm x 122cm)

11483

43462

24' x 52" (732cm x 132cm)

12481

47241

ULTRA FRAME
POOL

16' x 48" (488cm x 122cm)

5061

19156

18' x 52" (549cm x 132cm)

6981

26423

SEQUOIA SPIRIT®
POOL SET

16'8" x 49" (508cm x 124cm)

5061

19156

18'8" x 53" (569cm x 135cm)

6981

26423

18' x 10' x 42" (549cm x 305cm x 107cm)

2885

10920

20' x 12' x 48" (610cm x 366cm x 122cm)

4393

16628

OVAL FRAME
POOL

RECT. ULTRA
FRAME POOL

24' x 12' x 48" (732cm x 366cm x 122cm)

5407

20465

28' x 12' x 48" (853cm x 366cm x 122cm)

6420

24300

18' x 9' x 52" (549cm x 274cm x 132cm)

4545

17203

24' x 12' x 52" (732cm x 366cm x 132cm)

8403

31805

32' x 16' x 52" (975cm x 488cm x 132cm)

14364

54368

NOTE: The “12” hours timer setting position has an additional 20 minutes over the actual
setting.

SAVE THESE INSTRUCTIONS

Page 22

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

English

128

NON-INTEX POOLS OPERATING TIME TABLE
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
Sand filter pump operating
time (For one cycle)

Water Capacity
(Gals)

(Liters)

(Hours)

4000

15140

5000

18925

6000

22710

7000

26495

8000

30280

9000

34065

10000

37850

11000

41635

12000

45420

13000

49205

14000

52990

15000

56775

16000

60560

17000

64345

18000

68130

19000

71915

20000

75700

21000

79485

22000

83270

23000

87055

24000

90840

25000

94625

26000

98410

SAVE THESE INSTRUCTIONS

Page 23

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

MAI NTENANCE

English

MOTOR PRE-FILTER CLEANING AND MAINTENANCE
1. Make sure the filter pump is switched off, then disconnect the power cord from
the electrical outlet.
2. Grasp a plunger valve handle. Turn the handle counter-clockwise, push down
until it stops and then turn it clockwise until the plastic protruding notch anchors
in the "0/1" position. Repeat for the second plunger valve. This prevents the
water from flowing out of the pool.
36

3. Release the pressure first by opening the
sediment release valve (18) located
on the lower side of the pre-filter housing
(see drawing 36).
1

4. In a counter-clockwise motion unscrew the
leaf trap cover (13), then remove the
basket (15) and leaf trap o-ring (14) from the
pre-filter housing (see drawing 37).

5. Empty and flush the basket using a garden hose, may use a plastic brush to
remove deposits from the basket. Do not use metal brush.
6. Clean and rinse the inside of the pre-filter housing and the leaf trap O-ring with
a garden hose.
7. Reinstall the leaf trap O-ring, basket and leaf trap cover to the pre-filter housing.
8. Close the sediment release valve (18) back.

SAVE THESE INSTRUCTIONS

Page 24

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

MAI NTENANCE

English

POOL CARE & CHEMICALS
•

•
•
•

All pools require care to keep the water clear and hygienically clean. With proper
chemical control, your filter will help attain this objective. Consult your pool supply dealer
for instructions regarding the proper use of chlorine, algaecide and other chemical
agents required for sparkling clear water.
Keep pool chemicals away from children.
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could
occur.
Daily pH checking and chemical treatment of the water is very important and cannot be
overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required
when filling the pool as well as during the season. Consult your local swimming pool
supply store for instructions.
The season's first filling of the pool may have brackish water requiring extra water
additives and extra filtering time. Do not allow swimming in pool until the pH level is
balanced. Consult your local swimming pool supply store for instructions.
Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool
and splash water outside the pool. Lawn areas underneath the pool liner will be
destroyed. Note that some types of grass may grow through the liner.
Filter run time depends on pool size, weather and usage level. Experiment with various
run times so as to produce clean clear water.

CAUTION
Concentrated chlorine solutions may damage the pool liner. Always follow the
chemical manufacturer’s directions, and the health and hazard warnings.

LONG TERM STORAGE & WINTERIZATION

CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is
non-toxic and will not damage plastic system components; other anti-freezes
are highly toxic and may damage plastic components in the system.
1.

Before emptying your pool for long term storage, or relocation, be sure the water is
directed towards an acceptable drain water receptacle away from the house. Check local
regulations for specific directions regarding disposal of swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves and
remove the strainers/plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (6) from the drain valve to
thoroughly drain the tank. The drain valve is located at the bottom of the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term storage:
• L-shape o-ring (9).
• o-ring A (17).
• Pump hose O-rings (21).
• Strainer valve assembly step washers (22).
• Flat strainer rubber washers (24).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve top
“N” position. This allows the water to drain from the valve. Leave the 6-way valve in this
inactive position.
9. It is best to place all dry pieces and pump motor in the original packaging for storage. To
avoid condensation or corrosion problem, do not cover or wrap pump motor with plastic bags.
10. Store the pump motor and accessories in a dry place. The storage's temperature
should be controlled, between 0 degrees Celsius (32 degrees Fahrenheit) and 40
degrees Celsius (104 degrees Fahrenheit).

SAVE THESE INSTRUCTIONS

Page 25

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

TROUBLESHOOTING GUIDE
TROUBLE

CAUSE

SOLUTION

FILTER MOTOR
FAILS TO START

• Line cord must be plugged into a 3
• The motor is not plugged in.
wire outlet that is protected by a Class
• The fuse box needs checking.
A Ground Fault Circuit Interrupter, or
• The GFCI/RCD circuit breaker
RCD.
is tripped.
• Reset circuit breaker. If circuit breaker
• Motor too hot and overload
trips repeatedly, your electrical system
protection is shut off.
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let the motor cool down and restart again.

FILTER DOESN’T
CLEAN POOL

• Improper chlorine or pH
levels.
• No filtering media in tank.
• Wrong 6-way valve setting
position.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.

• Adjust the chlorine and pH level. Consult
your local swimming pool supply stores.
• Load with filter sand, see “sand loading
instructions”.
• Set valve to “ FILTER” position.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.

FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY
SLOW

•
•
•
•
•

Clogged inlet or discharge.
An air leak on the intake line.
Excessively dirty pool.
Sand media clogged with dirt.
Nozzle and strainer
connections are reversed.
• Crusting or caking on the
filtering sand surface.
• Pool vacuuming device
attached to the system.

• Clear any obstructions in the intake
hose by discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Clean the pre-filtering basket more often.
• Backwash filter.
• Install the nozzle at the upper position
of the pool inlet, and the strainer at the
lower position of the pool outlet.
• Remove about 1” of sand if necessary.
• Remove any pool vacuuming device
attached to the system line.

PUMP DOESN’T
WORK

•
•
•
•

Low water level.
Strainer screen clogged up.
An air leak on the intake hose.
Faulty motor or the impeller
is jammed.

• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for
damage.
• Contact Intex service center.

6-WAY
VALVE/COVER
LEAKING

•
•
•
•

Sand tank o-ring missing.
Sand tank o-ring dirty.
Flange clamp not tight.
6-way valve damage.

• Remove 6-way valve cover and ensure the
o-ring is in place.
• Clean sand tank o-ring with garden hose water.
• Tighten the clamp with wrench supplied.
• Contact Intex service center.

HOSE LEAKING

• Hose nut not securely tight.
• Hose connection fitting
o-ring/L-shape o-ring missing.

• Tighten/reinstall hose nut.
• Ensure o-ring/L-shape o-ring is in place
and not damaged.

TIMER IS
INACCURATE OR
TIMER CAN'T BE
SET

• Possible inner timer
defective.

• Turn off the pump and restart 5 minutes
later.
• Re-set the timer.
• Contact Intex service center.

PRESSURE GAUGE
DOESN’T WORK

• Clogged inlet of the pressure
gauge.
• Pressure gauge damage.

• Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
• Contact Intex service center.

SAND IS FLOWING
BACK INTO THE
POOL

• Sand is too small.
• Sand bed is calcified.

• Use only No. 20 silica sand with particle
size range 0.45 to 0.85 mm (0.018
to 0.033 inches) and a Uniformity
Coefficient less than 1.75.
• Change sand.

SAVE THESE INSTRUCTIONS

Page 26

TROUBLESHOOTING GUIDE

English

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

COMMON POOL PROBLEMS
PROBLEM

DESCRIPTION

CAUSE

SOLUTION

ALGAE

• Greenish water.
• Green or black
spots on pool liner.
• Pool liner is
slippery and/or has
a bad odor.

• Chlorine and pH levels
need adjustment.

• Super chlorinate with shock
treatment. Correct pH to your
pool store's recommended
level.
• Vacuum pool bottom.
• Maintain proper chlorine
level.

COLORED
WATER

• Water turns blue,
brown, or black
when first treated
with chlorine.

• Copper, iron or
maganese in water
being oxidized by the
added chlorine.
This is Common.

• Adjust pH level to the
recommended level.
• Run filter until water is clear.

FLOATING
MATTER IN
WATER

• Water is cloudy or
milky.

• "Hard water" caused
by a too high pH level.
• Chlorine content is low.
• Foreign matter in
water.

• Correct the pH level. Check
with your pool dealer for
advice.
• Adjust the chlorine level.

CHRONIC
LOW WATER
LEVEL

• Level is lower than
on previous day.

• Rip or hole in pool
liner or hoses.
• The drain valves are
loose.

• Repair with a patch kit.
• Finger tighten all caps.

SEDIMENT
ON POOL
BOTTOM

• Dirt or sand on
pool floor.

• Heavy use, getting in
and out of pool.

• Use Intex pool vacuum to
clean bottom of pool.

SURFACE
DEBRIS

• Leaves, insects
etc.

• Pool too close to
trees.

• Use Intex pool skimmer.

IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.

SAVE THESE INSTRUCTIONS

Page 27

COM MON PROBLEMS

English

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

128

SAFETY GUIDELINES

English

GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.

SAVE THESE INSTRUCTIONS

Page 28

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

English

128

LIMITED WARRANTY
Your Sand Filter Pump has been manufactured using the highest quality materials and
workmanship. All Intex products have been inspected and found free of defects prior to
leaving the factory. This Limited Warranty applies only to the Sand Filter Pump.
The following provision is only valid within the European member states countries: The
legal regulation of Directive 1999/44/EC will not be effected by this Intex warranty.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for a period of two (2) years from the date of
the initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty
is invalid.
If a manufacturing defect is found within this two (2) years period, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will determine
the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN
NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE
LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL
DAMAGES OR LIABILITIES. Some countries, or jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
This Limited Warranty does not apply if the Sand Filter Pump is subject to negligence,
abnormal use or operation, accident, improper operation, improper voltage or current
contrary to operating instructions, or to damage by circumstances beyond Intex’s control,
including but not limited to, ordinary wear and tear and damage caused by exposure to
fire, flood, freezing, rain, or other external environmental forces. This Limited Warranty
applies only to those parts and components sold by Intex. The Limited Warranty does not
cover unauthorized alterations, repairs or disassembly by anyone other than Intex
Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered by
this warranty.

SAVE THESE INSTRUCTIONS

Page 29

(128) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/18/2010

English

128

For service questions or to order replacement parts, please contact the appropriate
office listed below or visit www.intexdevelopment.com for answers to most
frequently asked questions.
AREAS
•

ASIA

•

EUROPE

•

FRANCE

•

GERMANY

•

ITALY

•

SWITZERLAND

•

SPAIN / PORTUGAL

•

AUSTRALIA

•

NEW ZEALAND

•

MIDDLE EAST
REGION

•

SOUTH AFRICA

•

CHILE / URUGUAY

LOCATION

INTEX DEVELOPMENT CO. LTD.
9TH FLOOR,
DAH SING FINANCIAL CENTRE,
108 GLOUCESTER ROAD,
WANCHAI, HONG KONG
TEL: 852-28270000
FAX: 852-23118200
E-mail: xmservicesupport@intexcorp.com.cn
Website: www.intexdevelopment.com
INTEX TRADING B.V.
POSTBUS 1075, 4700 BB ROOSENDAAL,
THE NETHERLANDS
TEL: 31-(0)165-593939
FAX: 31-(0)165-593969
E-mail: service@intexcorp.nl
Website: www.intexcorp.nl
UNITEX / INTEX SERVICE FRANCE S.A.S
52, ROUTE NATIONALE,
39190 BEAUFORT, FRANCE
TEL: 08 90 71 20 39 (0,15€/min)
FAX: 03 84 25 18 09
Website: www.intex.fr
STEINBACH VERTRIEBSGMBH
C/O WEBOPAC LOGISTICS GMBH
INTER-LOGISTIK-PARK 1-3
87600 KAUFBEUREN
TEL: 0180 5 405 100 200
(0,14€/min aus dem Festnetz, Mobilfunk max. 0,42€/min)
FAX: + 43 (7262) 61439
E-mail: service@intexcorp.de
Website: www.intexcorp.de
A & A MARKETING SERVICE
VIA RAFFAELLO SANZIO
20058 VILLASANTA (MI)
TEL: 199 12 19 78
FAX: +39 039 2058204
E-mail: info@intexitalia.com
Website: www.intexitalia.com
TOY BROKERS LTD
MARKETING HOUSE,
BLACKSTONE ROAD,
HUNTINGDON, CAMBS.
PE29 6EF. UK
TEL: 0844 561 7129
FAX: 01480 414761
E-mail: sales@toybrokers.com
Website: www.intexspares.com
GWM AGENCY
GARTEN-U. WOHNMÖBEL,
RÄFFELSTRASSE 25,
POSTFACH,
CH-8045 ZURICH/SWITZERLAND
TEL: 0900 455456 or +41 44 455 50 60
FAX: +41 44 455 50 65
E-mail: gwm@gwm.ch
Website: www.gwm.ch, www.gwmsale.ch
Nostrum Iberian Market S.A.
Av. de la Albufera, 321
28031 Madrid, Spain
TEL: +34 902101339
FAX for Spain: +34 9 029 089 76
Email for Spain: sat@intexiberian.com
FAX for Portugal: +351 707 506 090
Email for Portugal: spv-pt@intexiberian.com
Website: www.intexiberian.com
HUNTER PRODUCTS PTY LTD
LEVEL 1, 225 BAY STREET,
BRIGHTON, VICTORIA,
AUSTRALIA
TEL: 61-3-9596-2144 or 1800-224-094
FAX: 61-3-9596-2188
E-mail: enquiries@hunteroverseas.com.au
Website: www.hunterproducts.com.au
HAKA NEW ZEALAND LIMITED
UNIT 4, 11 ORBIT DIVE, ALBANY,
AUCKLAND 0757, NEW ZEALAND
TEL: 649-4159213 / 0800 634434
FAX: 649-4159212
E-mail: geoff@hakanz.co.nz
Website: www.hakanz.co.nz
FIRST GROUP INTERNATIONAL
AL MOOSA GROUP BUILDING, 1ST
FLOOR, OFFICE 102 & 103, UMM HURAIR
ROAD, KARAMA, DUBAI, UAE
TEL: 00971-4-800INTEX(46839) / +971-4-3373322
FAX: 00971-4-3375115
E-mail: intex@firstgroupinternational.com.
Website: www.firstgroupinternational.com
WOOD & HYDE
15-17 PACKER AVENUE, INDUSTRIA 2,
CAPE TOWN, SOUTH AFRICA 7460
TEL: 27-21-0800-204-692
FAX: 27-21-505-5600
E-mail: ygoldman@melbro.co.za
COMEXA S.A.
EL JUNCAL 100, PARQUE INDUSTRIAL PORTEZUELO,
QUILICURA, SANTIAGO, CHILE.
TEL: 600-822-0700
E-mail: serviciotecnico@silfa.cl

•

AREAS

ARGENTINA

•

PERU

•

SAUDI ARABIA

•

AUSTRIA

•

CZECH REPUBLIC /
EASTERN EUROPE

•

BELGIUM

•

DENMARK

•

SWEDEN

•

NORWAY

•

FINLAND

•

RUSSIA

•

POLAND

•

HUNGARY

•

BRASIL

•

ISRAEL

SAVE THESE INSTRUCTIONS

LOCATION

JARSE INDUSTRIAL Y COMERCIAL S.A
MANUEL GARCIA Nº124, PARQUE PATRICO,
BUENOS AIRES, ARGENTINA
TEL: 4942-2238 (interno 106);
TEL: 4942-2238( interno 145)
E-mail: Martín Cosoleto: mcosoleto@jarse.com.ar
E-mail: Daniel Centurion: dcenturion@jarse.com.ar
Website: www.jarse.com.ar
COMEXA S.A.
AVENIDA COMANDANTE ESPINAR 142,
MIRAFLORES, LIMA, PERÚ
TEL: 446-9014
SAUDI ARABIAN MARKETING &
AGENCIES CO. LTD.
PRINCE AMIR MAJED STREET,
AL-SAFA DISTRICT. JEDDAH,
KINGDOM OF SAUDI ARABIA
TEL: 966-2-693 8496
FAX: 966-2-271 4084
E-mail: toy@samaco.com.sa
Website: www.samaco.com.sa
STEINBACH VERTRIEBSGMBH
AISTINGERSTRAßE 2
4311 SCHWERTBERG
TEL: 0820 - 200 100 200
(0,145€/min aus allen Netzen)
FAX: + 43 (7262) 61439
E-mail: service@intexcorp.at
Website: www.intexcorp.at
INTEX TRADING S.R.O.
BENESOVSKA 23,
101 00 PRAHA 10,
CZECH REPUBLIC
TEL: +420-267 313 188
FAX: +420-267 312 552
E-mail: info@intexcorp.cz
N.V. SIMBA-DICKIE BELGIUM S.A.
MOESKROENSESTEENWEG 383C,
8511 AALBEKE, BELGIUM
TEL: 0800 92088
FAX: 32-56.26.05.38
E-mail: intex@nicotoy.be
E-mail: intexsupport@nicotoy.be
Website: www.nicotoy.be/downloads.htm
K.E. MATHIASEN A/S
SINTRUPVEJ 12, DK-8220
BRABRAND, DENMARK
TEL: +45 89 44 22 00
FAX: +45 86 24 02 39
E-mail: intex@keleg.dk
Website: www.intexnordic.com
LEKSAM AB
BRANDSVIGSGATAN 6,
S-262 73 ÄNGELHOLM,
SWEDEN
TEL: +46 431 44 41 00
FAX: +46 431 190 35
E-mail: intex@leksam.se
Website: www.intexnordic.com
NORSTAR AS
PINDSLEVEIEN 1,
N-3221 SANDEFJORD,
NORWAY
TEL: +47 33 48 74 10
FAX: +47 33 48 74 11
E-mail: intex@norstar.no
Website: www.intexnordic.com
NORSTAR OY
SUOMALAISTENTIE 7,
FIN-02270 ESPOO,
FINLAND
TEL: +358 9 8190 530
FAX: +358 9 8190 5335
E-mail: info@norstar.fi
Website: www.intexnordic.com
LLC BAUER
KIEVSKAYA STR., 20,
121165 MOSCOW, RUSSIA
TEL: 099-249-9400/8626/9802
FAX: 095-742-8192
E-mail: intex.russia@gmail.com
Website: www.intex.su
KATHAY HASTER
UL. LUTYCKA 3, 60-415 POZNAN
TEL: +48 61 8498 334
FAX: +48 61 8474 487
E-mail: inx@kathay.com.pl
Website: www.intexpoland.pl
RECONTRA LTD./RICKI LTD.
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,
HUNGARY
TEL: +361 372 5200/113
FAX: +361 209 2634
E-mail: service@recontra.hu
KONESUL MARKETING & SALES LTDA
RUA ANTONIO DAS CHAGAS,
1.528 - CEP. 04714-002,
CHÁCARA SANTO ANTONIO - SÃO
PAULO - SP - BRASIL
TEL: 55 (11) 5181 4646
FAX: 55 (11) 5181 4646
E-mail: sacintexbrasil@uol.com.br
ALFIT TOYS LTD
MOSHAV NEHALIM,
MESHEK 32, 49950, ISRAEL
TEL: +972-3-9076666
FAX: +972-3-9076660
E-mail: michald@chagim.co.il

Page 30

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Count                      : 30
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:4f2d2112-f85a-11df-8769-000d93400d92
Producer                        : QuarkXPress(R) 7.31
Modify Date                     : 2010:11:25 14:07:40+08:00
Create Date                     : 2010:08:17 11:32:29Z
Creator Tool                    : QuarkXPress(R) 7.31
Metadata Date                   : 2010:11:25 14:07:40+08:00
Document ID                     : uuid:9e1c1192-f6ce-11df-9cb7-000d93400d92
Format                          : application/pdf
Title                           : 128---A0-11-- EN
Creator                         : QuarkXPress(R) 7.31

EXIF Metadata provided by EXIF.tools

128 A0 11 EN !! SF20220RSandfilterpump

Preview ! SF20220RSandfilterpump Leapfrog Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Navigation menu

Versions of this User Manual:

Views

Navigation