N9310A RF Signal Generator Data Sheet Brochure
User Manual: N9310A-RF-Signal-Generator-Data-Sheet-Brochure
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Keysight N9310A RF Signal Generator 9 kHz to 3.0 GHz Data Sheet 02 | Keysight | N9310A RF Signal Generator - Data Sheet Definitions and Conditions “Specifications” describe the performance of parameters that apply to the full temperature range of 5 to 45 °C, unless otherwise noted. “Typical” values describe additional product performance information. It is performance beyond specifications that 80 percent of the units exhibit with a 95 percent confidence level over the temperature range 20 to 30 °C. Typical performance does not include measurement uncertainty. “Nominal” values indicate expected performance, or describe product performance that is useful in the application of the product. The signal generator will meet its specifications when: –– It is within its calibration cycle –– It has been turned on at least 45 minutes –– It has been stored at an ambient temperature within the allowed operating range for at least two hours before being turned on; if it had previously been stored at a temperature range inside the allowed storage range, but outside the allowed operating range 03 | Keysight | N9310A RF Signal Generator - Data Sheet Specifications Supplemental information Frequency Range Resolution Switching speed Frequency reference Aging rate Temperature stability Timebase reference output Frequency Amplitude Connector External reference input Range Amplitude Connector and impedance Output Power Resolution Accuracy Switching speed VSWR (typical) Output connector and impedance Reversal power protection DC voltage RF power Spectral purity SSB phase noise Residual FM Harmonics Non-harmonics 9 kHz to 3.0 GHz 0.1 Hz < 10 ms Option PFR ± 1 ×10 −7 /year ± 1.5 ×10 −7 /2 years ± 1.5 ×10 −8 (20 to 30 °C) ± 5 ×10 −8 (5 to 50 °C) Typical; Within 0.1 ppm of final frequency Standard ± 1 ×10 −6 / year ± 1 ×10 −6 (5 to 45 °C) 10 MHz > 0.35 Vrms level into 50 Ω BNC female 2 MHz, 5 MHz, 10 MHz 0.5 to 2 Vrms 50 Ω; BNC female –127 to +13 dBm 0.1 dB < ± 1 dB < 10 ms < 1.6 < 1.8 N-type; 50 Ω nominal 30 V +36 dBm < –95 dBc/Hz < 30 Hz rms; < 90 Hz peak < 20 Hz rms < –30 dBc < –50 dBc +20 dBm settable Fc ≥ 100 kHz, –120 ≤ Level ≤ +13 dBm, 20 to 30 °C Typical; < 0.3 dB deviation 1.5 MHz ≤ Fc ≤ 2.5 GHz 2.5 GHz ≤ Fc ≤ 3 GHz 1 minute; the warning for reversed power protection is nominally at +25 dBm Typical, Fc = 1 GHz at 20 kHz offset CW mode, Fc = 1 GHz; BW = 0.3 to 3 kHz Res FM optimized mode Level ≤ 0 dBm, Fc ≥ 1 MHz Level ≤ 0 dBm, ≥ 10 kHz from carrier 04 | Keysight | N9310A RF Signal Generator - Data Sheet Specifications (continued) Supplemental information Characteristic SSB phase noise fc = 1,000 MHz fc = 2,000 MHz Sweep modes RF and LF LF sweep range RF sweep range Sweep points Dwell time Amplitude Sweep range Sweep points Dwell time 20 Hz to 80 kHz 9 kHz to 3 GHz 2 to 1,001 10 ms to 1 s –127 to +13 dBm 2 to 1,001 10 ms to 1 s Simultaneous modulation 1 AM AM 1. ØM Pulse Internal External Internal External Internal External − • − • • • − − External • − − • • • − − • • • • − − − • Internal • • • − • − • • External • • • − − − • • • • • − − − • • Internal − − • • • • − − External − − • • • • − − ØM Pulse FM Internal I/Q FM I/Q The N9310A has one external modulation input connector. The simultaneous external modulations are applied to the same input signal. 05 | Keysight | N9310A RF Signal Generator - Data Sheet Specifications (continued) Supplemental information Amplitude modulation Operating modes Range Resolution Rates Accuracy (Fc ≥ 100 kHz) Internal, external AC 0 to 100% 0.1% 20 Hz to 20 kHz < ± (5% of setting +0.2%) Distortion < 2% External input Sensitivity Input impedance Frequency modulation Operating modes Frequency deviation Resolution Rates Distortion MOD IN connector 0.5 Vpeak BNC; > 100 kΩ (Fc ≥ 100 kHz) Internal, external AC 20 Hz to 100 kHz < 1% 20 Hz to 80 kHz 1% Deviation accuracy < ± (5% of FM deviation +300 Hz) Carrier frequency deviation External input Sensitivity Input impedance Phase modulation Operating modes Phase deviation < 200 Hz MOD IN connector 0.5 Vpeak BNC; > 100 kΩ (Fc ≥ 100 kHz) Internal 0 to 10 rad 0 to 5 rad < 1% 300 Hz to 20 kHz < ± (5% of FM deviation +0.2 rad) < 1.5% Resolution Rates Deviation accuracy Distortion Input impedance Pulse modulation Operating modes On/Off ratio Rise/Fall time Pulse width Pulse period Time resolution Input connector and voltage level BNC; > 100 kΩ Internal, external ≥ 40 dB < 3 μs 100 μs to 1 s 200 μs to 2 s 1 μs BNC female; TTL Envelope peak < maximum specified power 1 kHz, 0 dBm and 80% modulation, 0.3 to 3 kHz bandwidth 1 kHz, 0 dBm and 80% modulation, 0.5 to 15 kHz bandwidth Input voltage for 100% modulation depth Nominal Minimum 1 Hz 1 kHz rate, 0.3 to 3 kHz bandwidth, deviation = 50 kHz 1 kHz, 0 dBm and 50 kHz deviation, 0.3 to 3 kHz bandwidth Relative to carrier; external mode Input voltage for 100 kHz modulation deviation Nominal Rate ≤ 10 kHz 10 kHz < rate ≤ 20 kHz 1 kHz rate, 0.3 to 3 kHz bandwidth 1 kHz rate, 0.3 to 3 kHz bandwidth, deviation = 5 rad Nominal Internal, external Internal 06 | Keysight | N9310A RF Signal Generator - Data Sheet Specifications (continued) Internal modulation source Waveform Frequency range Supplemental information Provides a modulation signal for AM, FM, phase modulation, and LF out Sine 20 Hz to 80 kHz Resolution Accuracy LF out (Internal modulation source) Amplitude 0.1 Hz 0.005% Typical 0 to 3 Vpeak Level to high impedance Output voltage resolution Frequency response Total harmonic distortion Connector and impedance Precision frequency reference (option PFR) Output frequency Accuracy Temperature Stability 20 to 30 °C 5 to 50 °C Aging 1 year 2 years Achievable Initial Calibration Accuracy Output level Connector Calibration connection I/Q modulation (Option 001 only) Operating mode VSWR Full scale input < 1% < ± 0.2 dB < 0.1% BNC female; < 1Ω 1 mV minimum resolution 20 Hz to 20 kHz Typical; 20 Hz to 20 kHz, 30 kHz low pass filter Front panel Modulation frequency range Carrier suppression QPSK EVM GMSK phase error Connector and impedance DC to 20 MHz 40 dBc 3% 1.2 °rms BNC female; 50 Ω 2. 3. 10 MHz ± [(time since last adjustment × aging rate) + temperature stability+ calibration accuracy 2] 3 ± 1.5 ×10 −8 ± 5 ×10 −8 ± 1 × 10 −7 ± 1.5 × 10 −7 ± 4 × 10 −8 > +4 dBm BNC female, 50 Ω nominal, rear panel Mini USB port, real panel External I/Q inputs < 1.5 I2 + Q2 = 0.5 Vrms At 3 dB points Typical; modulation frequency = 10 kHz Typical; 1 Msps; 0.22 RRC filter Typical; 1 Msps; BT = 0.5 Rear panel Calibration accuracy depends on how accurately the frequency standard was adjusted to 10 MHz. If the adjustment procedure is followed, the calibration accuracy is given by the specification of the achievable initial calibration accuracy. The specification applies after the generator has been powered on for four hours. 07 | Keysight | N9310A RF Signal Generator - Data Sheet Specifications (continued) Supplemental information USB connector USB host interface USB device interface General Recommended calibration cycle Power requirement Power consumption Temperature range 3 x A plug 1 x B plug V 1.1 protocol V 1.1 protocol 2-year Keysight Technologies, Inc. has verified that the stability of this product’s architecture justifies a longer calibration interval of 2 years. Auto-ranging 100 to 240 Vac; 50 to 60 Hz 65 W 5 to 45 °C –20 to 70 °C 9.2 kg 132.5 x 320 x 400 mm Operating Storage Nominal HxWxD Weight Dimensions Display Resolution 640 x 480 Size 165.1 mm (6.5 in) diagonal (nominal) Data storage Internal 16 MB nominal External Supports USB 2.0-compatible memory devices EMC Complies with European EMC Directive 2004/108/EC –– IEC/EN 61326-1 or IEC/EN 61326-2-1 –– CISPR Pub 11 group 1, class A –– AS/NZS CISPR 11:2004 –– ICES/NMB-001:2004 This ISM device complies with Canadian ICES-001 Cet appareil ISM est conforme à la norme NMB-001 du Canada Safety Complies with European Low Voltage Directive 2006/95/EC –– IEC/EN 61010-1 2nd edition –– Canada: CSA C22.2 No. 61010-1-04 –– USA: UL 61010-1 2nd edition Audio noise Acoustic noise emission Geraeuschemission LpA < 70 dB LpA < 70 dB Operator position Am Arbeitsplatz Normal position Normaler Betrieb Per ISO 7779 Nach DIN 45635 t.19 Environmental stress Samples of this product have been type tested in accordance with the Keysight Environmental Test Maunal and verified to be robust against the environmental stresses of storage, transportation, and end-use; those stresses include, but are not limited to, temperature, humidity, shock, vibration, altitude, and power line conditions. Test methods are aligned with IEC 60068-2 and levels are similar to MILPRF-28800F Class 3 08 | Keysight | N9310A RF Signal Generator - Data Sheet Evolving Since 1939 Our unique combination of hardware, software, services, and people can help you reach your next breakthrough. We are unlocking the future of technology. From Hewlett-Packard to Agilent to Keysight. myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. www.keysight.com/find/emt_product_registration Register your products to get up-to-date product information and find warranty information. Keysight Services www.keysight.com/find/service Keysight Services can help from acquisition to renewal across your instrument’s lifecycle. Our comprehensive service offerings—onestop calibration, repair, asset management, technology refresh, consulting, training and more—helps you improve product quality and lower costs. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements. Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. www.keysight.com/find/n9310a For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 11 2626 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-9-7-17) DEKRA Certified ISO9001 Quality Management System www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2015 Quality Management System This information is subject to change without notice. © Keysight Technologies, 2017 Published in USA, December 1, 2017 5990-8116EN www.keysight.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36 Create Date : 2017:11:22 19:05:50-07:00 Metadata Date : 2017:11:22 19:05:53-07:00 Modify Date : 2017:11:22 19:05:53-07:00 Creator Tool : Adobe InDesign CC 13.0 (Macintosh) Instance ID : uuid:78a55969-1857-ae49-b875-024d649e1f19 Original Document ID : xmp.did:5259B79ADEA3E311A5169BB3BD84A224 Document ID : xmp.id:933474ba-2bba-45ee-a0c2-025688e32d62 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:cdf89bb7-865d-483f-9f37-98d3e1b929d2 Derived From Document ID : xmp.did:78FD55EE6743E411A395B60CE21BB301 Derived From Original Document ID: xmp.did:5259B79ADEA3E311A5169BB3BD84A224 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.0 (Macintosh) History Changed : / History When : 2017:11:22 19:05:50-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 8 Creator : Adobe InDesign CC 13.0 (Macintosh)EXIF Metadata provided by EXIF.tools