OmniPro II Installation Manual Omni Pro V2.16
User Manual: OmniPro II v2.16 Installation Manual AlarmHow.net Library
Open the PDF directly: View PDF 
.
Page Count: 76
| Download | |
| Open PDF In Browser | View PDF |
HOME AUTOMATION, INC. Control & Security System Includes the SIA CP-01 Control Panel Standard Features for False Alarm Reduction Installation Manual Document Number 20I00-2 Rev. 2.16 December, 2007 Home Automation, Inc. Installation Manual Includes the SIA CP-01 Control Panel Standard Features for False Alarm Reduction Document Number 20I00-2 Rev. 2.16 December, 2007 Copyright © 2001-2007 Home Automation, Inc. All Rights Reserved CONTENTS INTRODUCTION........................................................................................................................................... 1 PLANNING .......................................................................................................................................................................................1 INSTALLATION............................................................................................................................................ 2 CONTROLLER HOOKUP .............................................................................................................................................................2 ABOUT SECURITY ZONES ..........................................................................................................................................................4 BURGLAR ZONE HOOKUPS ..................................................................................................................................................4 ABOUT FIRE ZONES .....................................................................................................................................................................5 TWO-WIRE SMOKE DETECTORS .........................................................................................................................................6 FOUR-WIRE SMOKE DETECTORS .......................................................................................................................................6 TELEPHONE CONNECTIONS .....................................................................................................................................................9 DIGITAL SUBSCRIBER LINE (DSL) CONNECTIONS.........................................................................................................9 LCD CONSOLE HOOKUP...........................................................................................................................................................11 CONSOLE SETUP .........................................................................................................................................................................12 CONSOLE ADDRESS.............................................................................................................................................................12 SOUNDER................................................................................................................................................................................12 KEY CLICK .............................................................................................................................................................................12 KEY BACKLIGHT ..................................................................................................................................................................12 VIEWING ADJUSTMENT......................................................................................................................................................12 LANGUAGE ............................................................................................................................................................................12 EXIT SETUP MODE ...............................................................................................................................................................12 SOUNDER OUTPUTS ...................................................................................................................................................................14 INTERIOR SOUNDER HOOKUP...........................................................................................................................................14 EXTERIOR SOUNDER HOOKUP .........................................................................................................................................14 CONTROLLER OUTPUTS ..........................................................................................................................................................16 RESET OUTPUTS .........................................................................................................................................................................16 OUTPUT APPLICATIONS...........................................................................................................................................................16 GENERAL PURPOSE SWITCHING APPLICATIONS.........................................................................................................16 SOUNDER TRIGGERING ......................................................................................................................................................16 COMMUNICATOR OUTPUTS ..............................................................................................................................................17 "ARMED" AND "OK TO ARM".............................................................................................................................................17 SWITCHED OUTPUT .............................................................................................................................................................17 HAI COMMUNICATING THERMOSTATS..........................................................................................................................17 REMOTE ARM/DISARM SWITCH............................................................................................................................................17 HAI THERMOSTATS ...................................................................................................................................................................19 PROGRAMMABLE ENERGY SAVER MODULES .................................................................................................................20 TEMPERATURE, OUTDOOR TEMPERATURE, AND HUMIDITY ....................................................................................21 BUILT-IN SERIAL PORTS ..........................................................................................................................................................23 BUILT-IN ETHERNET PORT .....................................................................................................................................................24 CONTROLLER IP ADDRESS, PORT NUMBER, AND ENCRYPTION KEY.....................................................................24 CONTROLLER IP ADDRESS ................................................................................................................................................25 CONTROLLER PORT NUMBER ...........................................................................................................................................25 ENCRYPTION KEY ................................................................................................................................................................25 OMNIPRO II ETHERNET CONNECTIONS..........................................................................................................................25 CONNECTING TO NETWORK VIA PC ACCESS................................................................................................................26 SYSTEM POWER UP PROCEDURE ....................................................................................................... 28 CONSOLE CHECK OUT..............................................................................................................................................................28 TELEPHONE CHECK OUT ........................................................................................................................................................28 BURGLAR ZONE CHECK OUT .................................................................................................................................................29 FIRE ZONE CHECK OUT ...........................................................................................................................................................29 CUSTOMER CHECKOUT ...........................................................................................................................................................29 IN CASE OF TROUBLE ...............................................................................................................................................................30 CONSOLES..............................................................................................................................................................................30 CONTROLLER ........................................................................................................................................................................30 DIGITAL COMMUNICATOR................................................................................................................... 32 DESCRIPTION OF CONTACT ID..............................................................................................................................................32 DESCRIPTION OF 4/2 FORMAT ...............................................................................................................................................33 3/1 FORMAT ..................................................................................................................................................................................33 OPENING AND CLOSING REPORTS .......................................................................................................................................33 INSTALLER SETUP.................................................................................................................................... 34 SETUP CONTROL ........................................................................................................................................................................34 X-10 HOUSE CODE ................................................................................................................................................................34 UPB NETWORK ID ................................................................................................................................................................34 X-10 3-PHASE .........................................................................................................................................................................35 OUTPUT TYPES .....................................................................................................................................................................35 Z-WAVE NODE ID .................................................................................................................................................................36 SETUP ZONES...............................................................................................................................................................................37 ZONE EXPANSION ................................................................................................................................................................37 ZONE RESISTORS..................................................................................................................................................................37 ZONE TYPES ..........................................................................................................................................................................38 LATCHING ZONE TYPES .....................................................................................................................................................38 DESCRIPTION OF ZONE TYPES..........................................................................................................................................39 SETUP DIGITAL COMMUNICATOR .......................................................................................................................................42 FIRST PHONE NUMBER, FIRST ACCOUNT NUMBER ....................................................................................................42 COMMUNICATOR TYPE ......................................................................................................................................................42 TWO-WAY AUDIO.................................................................................................................................................................42 REPORT OPEN/CLOSE ..........................................................................................................................................................43 REPORT BYPASS / RESTORE ..............................................................................................................................................43 AUTOMATIC TEST TIME .....................................................................................................................................................43 ALARM CODES (4/2 and 3/1 Formats) ..................................................................................................................................43 SETUP AREAS...............................................................................................................................................................................44 SETUP AREAS: CONTROL ...................................................................................................................................................44 SETUP AREAS: ZONES .........................................................................................................................................................46 SETUP AREAS: BUTTONS....................................................................................................................................................46 SETUP AREAS: CONSOLES .................................................................................................................................................46 SET-UP AREAS: THERMOSTATS........................................................................................................................................47 SETUP AREAS: MESSAGES ................................................................................................................................................47 SETUP TEMPERATURES ...........................................................................................................................................................48 TEMPERATURE DISPLAY....................................................................................................................................................48 THERMOSTAT TYPE.............................................................................................................................................................48 Z-WAVE THERMOSTAT NODE ID......................................................................................................................................48 SETUP MISCELLANEOUS .........................................................................................................................................................49 INSTALLER CODE.................................................................................................................................................................49 ENABLE PC ACCESS.............................................................................................................................................................49 PC ACCESS CODE..................................................................................................................................................................49 CALL BACK PHONE NUMBER............................................................................................................................................49 OUTSIDE SIREN DELAY ......................................................................................................................................................49 DIAL OUT DELAY .................................................................................................................................................................50 ALARM RESET TIME ............................................................................................................................................................50 ARMING CONFIRMATION...................................................................................................................................................50 FIRE ALARM VERIFICATION .............................................................................................................................................50 SUPERVISE INT SNDR..........................................................................................................................................................51 SUPERVISE EXT SNDR.........................................................................................................................................................51 ENABLE EMERGENCY KEYS .............................................................................................................................................51 TIME DISPLAY.......................................................................................................................................................................51 DATE DISPLAY......................................................................................................................................................................51 AC POWER FREQUENCY .....................................................................................................................................................51 DEAD LINE DETECT.............................................................................................................................................................52 OFF HOOK DETECT ..............................................................................................................................................................52 PICKUP AFTER HANGUP .....................................................................................................................................................52 CLOCK ADJUSTMENT..........................................................................................................................................................52 MODEL AND SOFTWARE VERSION..................................................................................................................................52 RESET SYSTEM EEPROM ....................................................................................................................................................52 RESET SYSTEM RAM............................................................................................................................................................53 ETHERNET MAC ADDRESS.................................................................................................................................................53 SETUP EXPANSION .....................................................................................................................................................................53 MODULE 1 TYPE ...................................................................................................................................................................53 MODULE 2 TYPE - MODULE 4 TYPE .................................................................................................................................54 SERIAL 1 RATE ......................................................................................................................................................................54 SERIAL 1 FUNCTION ............................................................................................................................................................54 SERIAL 2 - SERIAL 5 RATE..................................................................................................................................................54 SERIAL 2 FUNCTION ............................................................................................................................................................54 SERIAL 3 FUNCTION ............................................................................................................................................................55 SERIAL 4 - SERIAL 5 FUNCTION ........................................................................................................................................55 SERIAL 6 RATE ......................................................................................................................................................................55 SETUP ZONE OPTIONS ..............................................................................................................................................................56 SWINGER SHUTDOWN NUMBER.......................................................................................................................................56 CROSS ZONE WINDOW........................................................................................................................................................56 ZONE 1 OPTIONS – ZONE 176 OPTIONS............................................................................................................................56 SIA CP-01 COMPLIANCE ......................................................................................................................... 57 Minimum Equipment Requirements for a CP-01 Compliant Installation: ...............................................................................57 OMNIPRO II SPECIFICATIONS.............................................................................................................. 58 UNDERWRITER'S LABORATORIES (UL) INSTALLATION REQUIREMENTS .......................... 59 24-HOUR STANDBY BATTERY CAPACITY......................................................................................... 60 SMOKE DETECTOR INSTALLATION GUIDELINES ........................................................................ 61 APPENDIX A – CONTACT ID REPORTING FORMAT....................................................................... 62 APPENDIX B - DIGITAL COMMUNICATOR CODE SHEET ............................................................ 63 APPENDIX C - ZONE AND UNIT MAPPING ........................................................................................ 68 FIGURES FIGURE 1 - CONTROLLER HOOKUP............................................................................................................................................3 FIGURE 2 - OVERALL CONNECTIONS DIAGRAM ....................................................................................................................5 FIGURE 3 - TWO-WIRE FIRE ZONE CONNECTIONS .................................................................................................................7 FIGURE 4 - FOUR-WIRE FIRE ZONE CONNECTIONS ...............................................................................................................8 FIGURE 5 - RJ31X JACK CONNECTIONS...................................................................................................................................10 FIGURE 6 – DSL SPLITTER CONNECTIONS .............................................................................................................................11 FIGURE 7 - CONSOLE CONNECTIONS ......................................................................................................................................13 FIGURE 8 - SOUNDER CONNECTIONS......................................................................................................................................15 FIGURE 9 - RESETTING CONTROLLER OUTPUTS..................................................................................................................16 FIGURE 10 - REMOTE KEYSWITCH CONNECTIONS ..............................................................................................................18 FIGURE 11 - HAI THERMOSTAT CONNECTIONS....................................................................................................................19 FIGURE 12 - TEMPERATURE / HUMIDITY SENSOR CONNECTIONS ..................................................................................21 FIGURE 13 - PESM CONNECTIONS ............................................................................................................................................22 FIGURE 14 - RS-232 CONNECTIONS...........................................................................................................................................23 FIGURE 15 - RS-485 CONNECTIONS...........................................................................................................................................24 FIGURE 16 - LOCAL NETWORK..................................................................................................................................................26 FIGURE 17 - LOCAL / WIDE AREA NETWORK ........................................................................................................................27 FIGURE 18 - 24-HOUR STANDBY CONNECTIONS ..................................................................................................................60 INTRODUCTION This installation guide is intended as an aid to installing the OmniPro II Control & Security System. The installer should also have thoroughly reviewed and understood the OmniPro II Owner's Manual, which has important information regarding final setup of the system. This manual assumes that the installer has a basic understanding of installing a security system. This guide applies to the 20A00-2, -5, and -22 versions of the OmniPro II series controller. Refer to the Underwriters Laboratories Installation Requirements section for details in the application of each. Failure to install the OmniPro II and its accessories in accordance with the UL Requirements in this manual and in the Owner's Manual, is a violation of the Listing Mark. PLANNING Before you start, your system should be planned as follows: 1. Zones: • Decide where each contact or detector will be located • Decide which zone it will occupy • Decide zone type for each zone • Decide which area it will occupy • With the customer, decide what text and voice descriptors will be used. Consult table of voice descriptors, so that you can choose similar words for the text to avoid customer confusion. • See SMOKE DETECTOR INSTALLATION GUIDELINES to plan locations for smoke detectors 2. Consoles: • Consult the customer on the console location. The console should be easily accessible. 3. Interior Sounder and Outside Siren: • Locate both where they cannot be tampered with. 4. Lighting and Appliance Switches and Modules. 5. Plan for thermostats, energy saver modules, or other options. 6. Give consideration to where the controller will go. Remember that it needs a duplex receptacle not controlled by a switch, preferably on its own circuit, within 5 feet of the controller. Page 1 INSTALLATION Go over your plan with your customer. 1. Install the entire system. Refer to sections in this manual to see how to install various components. 2. Follow the Power-Up and Checkout procedures. 3. Explain the basics to the customer. Deliver all manuals and documentation. 4. Follow up with your customer to keep them satisfied. CONTROLLER HOOKUP 1. When choosing a place to mount the controller, consider the following: a. A duplex outlet, preferably on its own circuit, is required to be within 5 feet of the controller for the power transformer and the UPB PIM or X-10 Interface Module. b. The controller should be protected from weather, temperature extremes, and burglars. 2. GROUND THE CONTROLLER "EARTH GND" TERMINAL TO A COLD WATER PIPE OR TO A 4-FOOT GROUND ROD TO PRESERVE ITS BUILT-IN TRANSIENT PROTECTION. USE 14 GAUGE WIRE. TRANSIENT PROTECTION WILL NOT WORK IF THE CONTROLLER IS NOT PROPERLY GROUNDED. 3. Connect the 24 VAC power transformer to the 24 VAC INPUT terminals. 4. Connect the BLACK battery wire to the minus (-) terminal on the battery. DO NOT connect the red wire at this time. DO NOT reverse the connections; the battery fuse will blow. Note that the unit will NOT START on the battery alone. 5. Connect the Powerline Interface Module to the OmniPro II controller: a) UPB PIM (P/N: 36A00-1): Plug one end of the 6-conductor modular cable into the connector marked “J3” (SERIAL 3) on the OmniPro II controller and plug the other end into the modular connector on the PIM. b) X-10 Interface Module (P/N: TW523): Plug one end of the 4-conductor modular cable into the connector marked “J7” (X-10) on the OmniPro II controller and plug the other end into the modular connector on the X-10 Interface Module. 6. Refer to FIGURE 1 (CONTROLLER HOOKUP) for this configuration. Page 2 1/4" SPACING BLACK WIRE TO RED WIRE TO + YUASA NP7-12 OR EQUIVALENT BATTERY 12V 7AH THE BATTERY IS NON-POWER LIMITED. THE BATTERY LEADS MUST BE SEPERATED FROM ALL OTHER POWER LIMITED/CLASS II WIRING IN THE ENCLOSURE BY AT LEAST 1/4" Status COLD WATER PIPE OR GROUND ROD> Network. ¾ If you are connecting from the local network, enter the controller’s IP address under “Network IP Address or Domain Name”. ¾ If you are connecting from the Internet, enter either the public IP address (the way to reach your local network via the Internet) or domain name (e.g. www.homeauto.com). 3. Enter the port number that is configured for the controller. 4. Select the Encryption tab. Enter the two part encryption key as it is displayed on the console. 5. Select OK. 6. Click Connect >> Network >> Connect. PC Access should change from “Off-Line” to “On-Line”. The “Modem” item on the main menu has been replaced with the “Connect” item. The submenu under “Connect” then allows selection of “Modem”, “Serial” or “Network”. When an account file is opened, the connection type will default to “Serial”. 192.168.0.101 HAI OmniPro II Controller To connect to an OmniPro II controller on a local network using HAI PC Access, under Configure >> Network enter the controller’s IP address: Hub or Router 192.168.0.50 Computer (i.e. 192.168.0.101) 192.168.0.51 Computer FIGURE 16 - LOCAL NETWORK Page 26 To connect to an OmniPro II controller from the Internet using HAI PC Access, under Configure >> Network enter the public IP address: To connect to an OmniPro II controller on a local network using HAI PC Access, under Configure >> Network enter the controller’s IP address: (i.e. 134.42.112.8) (i.e. 10.0.0.230) FIGURE 17 - LOCAL / WIDE AREA NETWORK If the controller is connected to the Internet via a dynamic IP address, to locate and communicate with the controller from remote locations over the Internet using HAI PC Access, you must subscribe to a Dynamic DNS (Domain Name Service). Dynamic DNS is a service that maps your dynamic (changing) IP address to a static (permanent) hostname, allowing you to access your OmniPro II controller over the Internet using your static hostname instead of an IP address. A “client” program (typically provided by the Dynamic DNS provider) runs on a PC on your local network and is used to automatically update your Dynamic DNS provider with your current IP address. Several router/switch manufacturers have embedded a Dynamic DNS client into their router firmware. These devices work with several of the Dynamic DNS providers, including both free and commercial services. These devices are especially beneficial because the router can be powered up all the time, so the dynamic update is always current and is handled by a single device (the router/switch) in the local network. This allows you to locate and connect to the OmniPro II controller without having a computer on the local network powered up and running. Page 27 SYSTEM POWER UP PROCEDURE 1. Carefully review hookups to the zones, grounds, sounders, and consoles. 2. Disconnect 1 lead of both the interior and exterior sounders. NOTE: Follow this power up procedure to verify proper operation of the power supply, battery charger, and low voltage cut out relay. 3. The positive lead to the battery should be disconnected at this time. Make sure that the red battery wire is not touching anything. 4. Plug in the power transformer. - The AC ON LED should illuminate. - Within one minute, the STATUS LED should begin blinking at a rate of 1 blink per second. This indicates that the OmniPro II processor and software are working. - The PHONE LED should be OFF (if all telephones are on-hook and the RJ31X jack is properly connected. 5. Unplug the power transformer to kill the system. Connect the red battery wire to the + (positive) battery terminal. The system should not start. 6. Plug in the power transformer. The system should start. 7. Unplug the power transformer. The system should continue to run on the battery (the STATUS LED will continue to flash). 8. Plug the transformer back in and secure it to the outlet. CONSOLE CHECK OUT 1. The console(s) should be operating. Press ' * ' to silence the trouble beeper if it is beeping. Press OFF, 1, 1, 1, 1 (or the current User code) if the alarm is tripped. If the consoles are not operating properly, make sure that no two consoles have the same address, and check the wiring. 2. With all doors and windows closed and all motion detectors secure, the bottom line of the display should read SYSTEM OK. If there are any trouble indications that occurred during installation, press ' * ' to acknowledge them and silence the beeper. 3. Set the time and date by pressing the 9 key. Enter the Master Code, then press the 2 key. Enter the time on the keypad, then the DATE (enter date as 6 characters: January 1, 02 as 010102). 4. The console should now show the time and date on the top line and "SYSTEM OK" on the bottom line. TELEPHONE CHECK OUT 1. Verify that the Telephone Company surge arrestor is properly grounded. 2. Verify that the incoming telephone lines are run to the surge arrestor first, then from the surge arrestor to the RJ31X jack, then from the RJ31X jack to the house phones. 3. The PHONE LED, on the controller, should be off when the phones are hung up. 4. Pick up an in-house phone, wait about 1 second, then press the ' # ' key. You should hear the Voice menu on the phone. If not, check to see that the RJ31X jack is properly wired and connected to the controller. There should be no interference from the Telephone Company while the menu is being read over the phone. Page 28 5. Record the owner's NAME and ADDRESS in the ADDRESS speech memory as shown in SETUP ADDRESS in the OWNER'S MANUAL (Press 8, 9, then 1111 or the current Master code to record the address). NOTE: DO NOT record any TOUCH TONES in the ADDRESS!! 6. Check that all in-house phones are working. BURGLAR ZONE CHECK OUT 1. With all doors and windows closed and all motion detectors and security devices secure, the console display should read "SYSTEM OK". 2. If any zones are abnormal, check your wiring. If the battery indication is low, make sure that the battery is connected securely. Give the battery a chance to charge. 3. From the top-level display, have a partner go around the house and trip each sensor one at a time. The display should indicate the correct zone "NOT RDY" when the zone is tripped, then return to "SYSTEM OK" when the zone is secured. Be sure that the zone type indicated (ENTRY/EXIT, PERIMETER, ETC.) is correct for the zone being tested. 4. If the zone being checked is armed, (i.e. PANIC or TAMPER type, which is always armed) the alarm will be activated. Press OFF and 1111 or the current User code to silence the alarm, or bypass the PANIC and TAMPER zone(s) before you start. 5. Reconnect the sirens. Be sure that no one is standing near a siren. Activate the alarm, and ensure that both the inside and, after a delay, outside sirens activate. FIRE ZONE CHECK OUT 1. Press ' * ' to return the console to the SYSTEM OK indication. Check the fire zone per the sensor manufacturer's instructions. The fire alarm should be activated (pulsing interior sounder, exterior siren). 2. Press ' * ' to silence the alarm. The display will still indicate that the FIRE ZONE is in alarm. 3. Press DAY or NIGHT or AWAY and the User code to arm the system, then OFF and the User code to disarm. This arm/disarm cycle will reset the smoke detector. If the cause for alarm (i.e. smoke) has cleared, the display will return to SYSTEM OK. NOTE: Be sure that the DIAL OUT DELAY is long enough so that you can cancel the alarm before the system dials out. CUSTOMER CHECKOUT After you have completed the system check out and everything works, be sure that the customer knows how to: 1. Disarm/silence the system (OFF, 1111 or current User code). HAVE THE CUSTOMER PRACTICE! 2. Change the codes. 3. Get the menu over the in-house phones. Page 29 You should also: 4. Demonstrate arming and disarming. 5. Demonstrate home control. 6. Demonstrate setup and programming. 7. Show him/her how to program the dial out numbers. 8. Deliver the Owner's Manual. 9. If the customer has subscribed to a central monitoring service, this should be explained to him/her. IN CASE OF TROUBLE CONSOLES If you experience trouble that seems to be with a console, try disconnecting the console and running the console self test as described under CONSOLE HOOKUPS in this manual. If the console does not run the self-test properly, it should be returned to HAI for repair. "NO CONTROLLER DATA" or erratic operation of the LCD display could be a result of: A and B terminals connected backwards, poorly, or 2 or more consoles have the same address. CONSOLE SELF TEST Use the self test mode to verify the proper operation of the console. 1. Disconnect the console from the controller. Connect +12 and GND terminals to a 12-volt source (or a fresh 9-volt transistor battery.) The console beeper will beep twice per second, the LCD backlight and the keypad key will be lit, and the LCD will display "NO CONTROLLER DATA". 2. Simultaneously press and hold the 7 and the down arrow (Ø) keys for approximately 3 seconds. The beeper will beep 5 times, the LCD backlight and keypad backlight will turn off, and the display will clear. The LED at the top right corner of the console will start to cycle through its different colors (red, green, yellow, then turns off). At the end of each cycle the beeper will beep once. 3. Press any key. The LCD backlight and the keypad key backlight will turn on. 4. Press the keys in the following order and verify that the appropriate character fills the screen. 0 - 9, *, #, AWAY (A), NIGHT (B), DAY (C), OFF (D), × (filled blocks), and Ø (blanks). If this is successful, the console is good. Simultaneously press and hold the 7 and down arrow (Ø) keys to exit the self test mode or disconnect power. CONTROLLER Check the AC ON (bottom) LED. If it is not lit, check for 24 VAC at the transformer connections. Check the STATUS (top) LED on the controller board. It should be blinking once per second, indicating the proper operation of the microprocessor and memory. If not, try powering the system down by disconnect the power transformer and battery, then reconnect both. The status light should begin blinking. If the AC ON LED is on and the STATUS light is still not blinking, check the AUX +12 V with a DC voltmeter. It should be 13.7 volts. If not, make sure that there isn't too much load on the system. Disconnect all loads. If the STATUS LED still won't blink, there is a problem with the controller board and it must be returned to HAI for repair. Page 30 Phone line problems, or problems with the OmniPro II voice are usually the result of the RJ31X jack being improperly wired. Check RJ31X jack wiring and polarity carefully, as described in TELEPHONE CONNECTIONS. In the event that the controller is found defective, the controller board can be removed without disconnecting the entire wiring from their terminals. The terminal strips can be removed from the controller board. Then the controller (or processor board) can be repaired and reinstalled easily. Follow this procedure for removing the controller board: 1. If possible, upload the programs and configuration. (This will not be possible if the status LED isn't flashing or if you can't get the voice to work.) 2. Unplug the power transformer. 3. Disconnect the battery 4. Disconnect the RJ31X modular cable at the jack!! If you only disconnect it at the OmniPro II controller only, the house phones won't work. 5. Disconnect the X-10 cable. Disconnect the serial cable(s). Disconnect Ethernet cable. 6. Carefully remove the four terminal strips from the controller board. Gently push down on terminal strip retention clips. These clips are located on either end of the strip and 2 in the middle. Slowly pull strip away from terminal block socket and secure. 7. Remove 9 screws and washers; 3 on the top edge, 3 on the bottom edge, and 3 in the middle of the controller. 8. Remove the controller board. 9. Wrap the controller board with protective material and pack carefully. HAI will not be responsible for returned items damaged due to inadequate packaging. 10. Call Home Automation, Inc. with the serial number for a Return Authorization number to help us track your return. Write the R. A. # on the outside of the package. 11. Return the controller to Home Automation, Inc. Please include your return address, any special shipping instructions and daytime phone number so that we can reach you if we have any questions. Also include a brief description of the problem that you are having. 12. INSTALLATION: follow the removal process in reverse. Follow the POWER UP and CHECK OUT procedures in this manual. 13. NOTE: When a controller is returned from being repaired, all setup and programming is lost. The board is returned with the factory default setup and programming. FOR HELP: Call HAI between the hours of 9:00 AM and 5:00 PM Central time, Monday - Friday, at (800) 229-7256. Page 31 DIGITAL COMMUNICATOR The OmniPro II digital communicator can use Contact ID, or Standard 4/2 or 3/1, (20 pps, 1800 Hz data, 2300 Hz handshake), or (10 pps, 1900 Hz data, 1400 Hz handshake), dual round compared format. Any central station with modern equipment can receive these formats. Compatible receivers are Ademco, Radionics, Osborne-Hoffman, Linear, FBI, and Silent Knight. It is up to the installer to verify compatibility. At the time of installation, the installer is required to verify compatibility and phone line seizure of the Digital Communicator. If the digital dialer does not get a handshake signal from the central station 45 seconds after it begins dialing, it hangs up and tries again. The dialer will try the FIRST PHONE NUMBER 5 times, then go to the SECOND PHONE NUMBER and try that 5 times. After that, the system will indicate COMMUNICATIONS FAILURE on the console display and the digital communicator will not try again until another reportable event occurs. The digital communicator will not dial out until the DIAL OUT DELAY has expired. If the alarm is canceled prior to the expiration of the DIAL OUT DELAY, no transmission will take place. After the DIAL OUT DELAY has expired, though, all alarm trips will be transmitted followed by a CANCEL code. When the digital communicator is used, all voice dial outs will be delayed for five minutes after the expiration of the dial out delay to allow time for the central station to call the premises after an alarm code has been sent. If the digital communicator is unable to successfully communicate with the central station, the user will be alerted to the trouble condition. When the system status is requested using the voice, this condition is reported over the phone as "SECURITY PHONE MESSAGE" trouble. Digital Communicator in Controller Phone Line Central Station Single Line Transmission Signal System Configuration DESCRIPTION OF CONTACT ID Contact ID reporting allows very specific event codes to be sent to the central station. A complete report takes under three seconds. Contact ID reporting uses predefined event codes that allow the central station to quickly identify the condition being reported. The specific security zone or user code is identified as part of the report. For each event code transmitted, the report also includes an event qualifier that identifies whether the report is for a new event (such as a security zone trip), or a restoration of an event (such as a security zone no longer tripped). Trouble conditions are reported, as well as restoration of these trouble conditions. For security armings and disarmings, this event qualifier is also used to identify whether the report is for an arm or disarm. The reporting format for Contact ID is listed in Appendix A in this manual. When using Contact ID, the alarm codes and/or reporting format cannot be changed. However, if the DCM code (under the 4/2 and 3/1 Alarm Code Formats) is set to “0” or “00”, then OmniPro II will not make a call to the central station to report that code when using Contact ID. Page 32 DESCRIPTION OF 4/2 FORMAT The 4/2 format consists of a four-digit account code, from 0000 to FFFF and a two-digit alarm code from 00 to FF. When the digital communicator calls the central station receiver, the latter answers and sends a brief 2300 Hz tone or a 1400 Hz tone called a "Handshake" tone. The digital communicator then reports digits of the account and alarm codes as bursts of either (1800 Hz) or (1900 Hz) tone; the digit 8 is represented by eight bursts of tone. A message, or "round" consists of an account code and an alarm code. Two rounds are sent, and two consecutive rounds must match at the receiver. If they do, the central station receiver sends another brief 2300 Hz or 1400 Hz tone to acknowledge to the digital dialer that the message has been properly received. If the rounds don't match, the receiver does not send the second tone and the digital dialer tries again, up to 5 times. If the rounds are not acknowledged after 5 tries, the digital dialer hangs up and tries the entire call again. The digital communicator can report alarm zone trips, alarm cancels, low battery, and fire zone trouble. It may also be setup to generate an automatic test signal at periodic intervals. The communicator may be setup to call second phone number using a second account number in the event that it is unable to communicate successfully using the first phone number and account. The digital communicator is setup at the factory to transmit a code when the battery is low or trouble with the fire zone is detected. If these codes are set to 0 or 00, no code will be sent when the trouble condition is detected. Although the alarm codes can be changed, we recommend that the alarm codes setup at the factory be used to minimize the risk of installer error in programming the digital communicator. Simply enter the phone numbers and account codes, then verify the alarm codes. 3/1 FORMAT Older central stations may require a 3/1 format. To use 3/1 format, both account numbers must be changed to 3 digit codes and EVERY alarm code must be changed to a 1-digit code. Do not mix code lengths! OPENING AND CLOSING REPORTS The OmniPro II system can send opening and closing reports by user to the central station. When the system is disarmed by user code 1-16, the communicator can call the central station and report that the system was disarmed (opened) with the user code that was used. When the system is armed by user code 1-16, the communicator can call the central station and report that the system was armed (closed) with the user code that was used. If any other code or a method disarms the system (i.e. Code 17-99, Keyswitch, or Scheduled Program), the communicator will send a generic OPEN report to the central station. The code that is sent is defined as OTHER OPEN. If the system is armed by any other method other than one that requires a code (i.e. Quick Arm, Keyswitch, or Scheduled Program), the communicator will send a generic CLOSE report to the central station. The code that is sent is defined as OTHER CLOSE. Page 33 INSTALLER SETUP This section describes the items that the installer must setup as part of system installation. The Installer Setup mode is used to configure the general operation of the system, the Outputs, the Areas, the Zone Types, the Digital Communicator, and various other settings. This information is covered only in this manual. All other SETUP items, including delay times, names and voices, voice dialer, and codes are covered in the Owner's Manual, Document No. 20R00-2. SETUP items are stored permanently in the system, even if the battery and AC power are disconnected. The "default" settings are the ones that have been set at the factory. You can review or change the setup items easily, as shown below. Note: The default Installer Code is 1111. To access the SETUP menu, press the 9 key and enter the installer code. To access the INSTALLER SETUP menu, press the # (INST) key. INSTALLER SETUP MENU: 1=CTRL 2=ZONE 3=DCM ↓ 4=AREA 7=EXP ↑ 5=TEMP 6=MISC SETUP CONTROL To configure X-10, UPB, voltage outputs, and Vizia RF Z-Wave options, from the Installer Setup menu, select the 1 (CTRL) key. The output type for both the interior and exterior horns may also be changed. Press (Ø) to advance to the next item, (×) to go back. X-10 HOUSE CODE The base X-10 house code must be specified. The base house code is the house code for units 1-16 and is referenced as house code 1. The house code for the units 17-32 is the next house code after the base house code, or house code "B" if the base house code is "A". House codes "C" through "P" follows for Units 33-256, respectively. X-10 HOUSE CODE: 1-16=A-P A ↓ UPB NETWORK ID The Network ID is a unique number between 1 and 255 which identifies your UPB Network. UPB NETWORK ID: 1-255 1 Enter the UPB Network ID (1-255) followed by the ' # ' key. UPB PASSWORD: The Network Password is a 4-digit number between 0001-FFFF that is used to protect your UPB network from unauthorized changes to the internal settings of your UPB devices. UPB PASSWORD: 0000-FFFF 1234 Enter the UPB Password (0000-FFFF) followed by the ' # ' key. To enter the digits A-F, first press the “OFF” key, then press the 0-5 key respectively (i.e. “1A2B” = 1 OFF 0 2 OFF 1 #). Page 34 UPB STATUS TIME (STATUS TRACKING): When using HLC, “Status Tracking” is used to update the status of each HLC device in a room whenever a scene is executed in that room. For example, the scene “A” button is pushed on a Room Controller in the Living Room. All of the lighting loads in the Living Room are changed, but the status for the individual lighting loads isn’t updated in OmniPro II until a status request message is sent to each unit. When “Status Tracking” is enabled, this is done automatically after a scene is executed. The value set for the UPB Status Time is the amount of seconds that the OmniPro II controller waits before requesting status after a scene is executed. By default, the time is set to 5 seconds. This gives lighting loads (with varying fade rates) the necessary time to “settle down” before the status is requested. UPB STATUS TIME: 0-255 SECONDS 5 Enter 1-255 for 1 to 255 seconds. Enter 0 to disable “Status Tracking”. Note: “Status Tracking” must be enabled for OmniPro II to accurately set the LED indicators on Room and House Controllers. X-10 3-PHASE This setting is used to select whether the X-10 signal is transmitted only at zero crossing for single phase (120V/240V) electrical systems or is transmitted at 0, 60, and 120 degrees for three phase electrical systems. X-10 3-PHASE: 0=NO 1=YES 0 To turn 3-Phase On, press 1 then ' # '. To turn 3-Phase Off, press 0 then ' # '. The burst at 60 and 120 degrees will be eliminated. The default setting for 3-Phase is No. OUTPUT TYPES An output type must be specified for each of the voltage outputs and for the interior and exterior horn outputs. The first group of outputs is global. This means that the output is valid for any area. The sounder and communicator outputs will be activated for an alarm in any area. The remaining types are area specific. This means that the output is only valid in the specified area. Area specific sounder and communicator types will only be activated for alarms in that area. The following output types are available: OUTPUT TYPE NUMBER Global A1 A2 A3 A4 A5 GENERAL PURPOSE 0 0 0 0 0 0 OK TO ARM 1 17 33 49 65 81 ARMED 2 18 34 50 66 82 PRE-ALM SNDR 3 19 35 51 67 83 INT SNDR 4 20 36 52 68 84 INT BURG SNDR 5 21 37 53 69 85 INT FIRE SNDR 6 22 38 54 70 86 EXT SNDR 7 23 39 55 71 87 EXT BURG SNDR 8 24 40 56 72 88 EXT FIRE SNDR 9 25 41 57 73 89 BURG COMM 10 26 42 58 74 90 FIRE COMM 11 27 43 59 75 91 AUX COMM 12 28 44 60 76 92 SWITCHED POWER 13 29 45 61 77 93 *Interior and Exterior Fire Sounders pulsate in a 3 pulse temporal pattern. Page 35 DESCRIPTION A6 0 97 98 99 100 101 102 103 104 105 106 107 108 109 A7 0 113 114 115 116 117 118 119 120 121 122 123 124 125 A8 0 129 130 131 132 133 134 135 136 137 138 139 140 141 General Purpose Output OK To Arm Output Armed Output Pre-Alarm Sounder Interior Sounder Interior Burglary Sounder Interior Fire Sounder * Exterior Sounder Exterior Burglary Sounder Exterior Fire Sounder* Burglary Communicator Fire Communicator Auxiliary Communicator Switched Power Output The Setup Control items are: OUTPUT 1 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 2 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 3 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 4 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 5 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 6 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 7 TYPE: 0 GENERAL PURPOSE #=CHNG OUTPUT 8 TYPE: 0 GENERAL PURPOSE #=CHNG INTERIOR HORN: INT SNDR #=CHNG 4 EXTERIOR HORN: EXT SNDR 7 #=CHNG ↑ For output types, the current setting is shown on the bottom line. Press the ' # ' key to select a new type from a list of types. The display shows: SELECT TYPE: INT SNDR 6 Use the Up and Down arrow keys to scroll through the list, or select the appropriate output type number. Then press ' # ' to enter the new type. If the Interior Horn is configured as a "General Purpose" output, Unit Number 393 is used to control the output. If the Exterior Horn is configured as a "General Purpose" output, Unit Number 394 is used to control the output. In this configuration, Unit Numbers 393 and 394 should not be used as "Flags". Z-WAVE NODE ID The Node ID is a unique number between 1 and 232 which identifies a Z-Wave device on the Vizia RF Z-Wave Network. Each Node must be associated (mapped) with a unit number in the OmniPro II controller. For Vizia RF Z-Wave pushbutton controllers, enter the Node ID for the Z-Wave pushbutton controller associated with that room (e.g. Unit 1, Unit 9, Unit 17, etc). If desired, more than one pushbutton controller may be assigned to a room by associating the pushbutton controller on any unit number in that room. If a second pushbutton controller is used, do not assign in a name in the controller. UNIT 1 NODE ID: 0-232 0 UNIT 232 NODE ID: 0-232 0 ↑ THROUGH Enter the Node ID (0-232) for each Z-Wave device followed by the ' # ' key. Enter 0 if there is no node associated with the specified unit number. Page 36 SETUP ZONES To configure zone expansion, zone resistors, and the zone types (definitions) for each security zone, from the Installer Setup menu, select the 2 (ZONE) key. Note: There zone options that define the way that each zone functions. To access Zone Options, press the 8 (ZOPT) key. ZONE EXPANSION Expansion Enclosures can be used to add additional zones to the OmniPro II system. Each Expansion Enclosure adds 16 zones to the system. If used, you must specify the number of Expansion Enclosures (1-8) used. Each Model 17A00 Expansion Enclosure adds 16 hardwired zones to the OmniPro II system. Wireless Receives can also be used to add additional zones to the OmniPro II system. When connected to an OmniPro II, the Wireless Receiver is recognized as an Expansion Enclosure. Each Wireless Receiver can handle up to 64 wireless zones, in groups of 16. Each group of 16 zones is considered 1 Expansion Enclosure. You must specify how many groups of wireless zones are being used. Specify the number of 17A00 Expansion Enclosures plus the number of wireless groups: NUMBER OF EXP ENCL 1-8 0 NOTES: 1. Up to 2 Model 10A06 Hardwire Expanders can be used with OmniPro II. Zones 1-16 on the first Expander are Zones 17-32 on OmniPro II. Zones 1-16 on the second Expander are Zones 33-48 on OmniPro II. 2. When used, the Model 10A06 Hardwire Expander Modules must be configured under Setup | Installer | Expansion. 3. Zones 1-16 on the first Expansion Enclosure are Zones 49-64 on OmniPro II. Zones 1-16 on the 2nd - 8th Expansion Enclosure are Zones 65 -176, respectively on OmniPro II. ZONE RESISTORS This item is used to specify if the 1000-ohm end-of-line zone resistors will be used with zone inputs on the controller and zone expanders (this does not affect Expansion Enclosures). If this item is set to "Yes", all zones are required to use an end-of-line resistor. End-of-line zone resistors are always required on Supervised Fire and Gas zones, and all zone inputs on Expansion Enclosures. The default setting is "Yes". ZONE RESISTORS: 0=NO 1=YES 1 Z 1 TYPE THROUGH Z176 TYPE This item specifies the zone type for each zone. All choices are listed in this manual under DESCRIPTION OF ZONE TYPES. For zone types, the current setting is shown on the bottom line. ZONE 1 TYPE: AUXILIARY 64 #=CHNG ZONE 176 TYPE: AUXILIARY 64 #=CHNG ↑ THROUGH Page 37 To change a zone type, press the ' # ' key, then use the arrow keys to scroll through the list of zone types. Press the ' # ' key to select a new type. The display shows: SELECT TYPE: PERIMETER 1 ZONE RESPONSE TIME All zones, in the OmniPro II are set to a 300 millisecond fixed response time. ZONE TYPES ZONE TYPE ENTRY/EXIT PERIMETER NIGHT INT AWAY INT 2X ENTRY DELAY 4X ENTRY DELAY LATCH PERIM LATCH NIGHT INT LATCH AWAY INT PANIC POLICE EMERG SILENT DURESS TAMPER LATCH TAMPER FIRE FIRE EMERG GAS AUX EMERG TROUBLE FREEZE WATER FIRE TAMPER AUXILIARY KEY SWITCH ENERGY SAVER OUTDOOR TMP TEMPERATURE TEMP ALARM HUMIDITY ER OUTDOOR TMP ER TEMPERATURE ER TEMP ALARM NUMBER 0 1 2 3 4 5 6 7 8 16 17 18 19 20 32 33 34 48 49 54 55 56 64 65 80 81 82 83 84 85 86 87 DESCRIPTION Entry/Exit Perimeter Night Interior Away Interior Double Entry Delay Quadruple Entry Delay Latching Perimeter Latching Night Interior Latching Away Interior Panic Police Emergency Duress Tamper Latching Tamper Fire Fire Emergency Gas Alarm Auxiliary Emergency Trouble Freeze Water Fire Tamper Auxiliary Keyswitch Input Programmable Energy Saver Module Outdoor Temperature Temperature Temperature Alarm Humidity Extended Range Outdoor Temperature Extended Range Temperature Extended Range Temperature Alarm LATCHING ZONE TYPES When any device (other then FIRE or GAS) is connected to SWITCH 12V or a Switched Power Output, the zone must be configured as one of the LATCHING ZONE TYPES (latching perimeter, latching night interior, latching away interior, and latching tamper). LATCHING ZONE TYPES ignore the status of that zone during power cycles. Used primarily when the FIRE ALARM VERIFICATION feature is being used or if more than one area is being protected. This type will ignore the status of LATCHING ZONES (i.e. Glassbreak Detectors) when the power is switched to reset devices. Page 38 DESCRIPTION OF ZONE TYPES ENTRY/EXIT ENTRY/EXIT ZONE types are intended for doors. ENTRY/EXIT ZONES are armed in security modes DAY, NIGHT, AWAY, and VACATION. In DAY and AWAY modes, there is an entry delay (defined by ENTRY DELAY) on ENTRY/EXIT ZONES to allow you to get into the house and turn off the alarm before it sounds. In NIGHT & DAY INSTANT mode, there is no entry delay, so that the alarm sounds immediately if someone opens a door. There are two special types of ENTRY/EXIT ZONES for use with garage doors, or doors that are far away from the control console. They are called DOUBLE ENTRY DELAY and QUADRUPLE ENTRY DELAY zones. These zones have double or quadruple the ENTRY DELAY to give you additional time to reach the console to disarm the system upon returning. Only the ENTRY DELAY is extended on these zone types. The EXIT DELAY is not extended. If an ENTRY/EXIT ZONE is tripped first, all other zones will are delayed. PERIMETER and LATCHING PERIMETER PERIMETER ZONE types are intended for windows and exterior doors not requiring an entry delay. All PERIMETER ZONES are armed in security modes DAY, NIGHT, AWAY, and VACATION. There is not an entry delay on a perimeter zones. If a window or door on this zone is opened while the security system is in DAY, NIGHT, AWAY or VACATION mode, the alarm will sound immediately. LATCHING PERIMETER ZONES ignore the status of that zone during power cycles. NIGHT INTERIOR and LATCHING NIGHT INTERIOR NIGHT INTERIOR ZONES are intended for motion detectors in areas where no one should be while you are sleeping in your home. For example, if you have a two-story home and sleep upstairs, your downstairs motion detector(s) should be on a NIGHT INTERIOR ZONE. NIGHT INTERIOR ZONES are armed in security modes NIGHT, VACATION, and AWAY only. There is no delay on a NIGHT INTERIOR ZONE. Night interior zones are NOT armed in DAY or DAY INSTANT mode, so that you may move about freely in your home when the security system is in DAY or DAY INSTANT mode, while still having the windows and doors protected. LATCHING NIGHT INTERIOR ZONES ignore the status of that zone during power cycles. AWAY INTERIOR and LATCHING AWAY INTERIOR AWAY INTERIOR ZONES are for areas of your home where no one should be while you are away. In the previous example, your upstairs motion detector(s) should be on an AWAY INTERIOR ZONE. AWAY INTERIOR ZONES are armed only when the security mode is AWAY. LATCHING AWAY INTERIOR ZONES ignore the status of that zone during power cycles. PANIC, TAMPER, and LATCHING TAMPER PANIC and TAMPER ZONES are for emergency pushbuttons and tamper switches. PANIC and TAMPER ZONES are always armed, even if the security mode is OFF. There are no delays on PANIC and TAMPER ZONES. An emergency dial out is activated after the DIAL OUT DELAY. TAMPER ZONES should be used for items such as gun cabinets and liquor closets. LATCHING TAMPER ZONES ignore the status of that zone during power cycles. POLICE EMERGENCY This zone type activates the burglar alarm and sounder. An emergency dial out is activated after the DIAL OUT DELAY. Page 39 DURESS EMERGENCY (SILENT DIAL OUT) If you wish to have a button in your home that activates a SILENT dial out, (no lights flashing and no sounder) it should be connected to a zone that is configured as a DURESS EMERGENCY. If this zone is accidentally tripped, you will not know that the OmniPro II is making a silent dial out, and hence won't know to stop it. To stop a silent dial out once it has started, you must go to the console and press OFF then enter your code. SUPERVISED FIRE Any zone can be programmed as a SUPERVISED FIRE ZONE. In UL Listed Installations, all fire detectors must be configured as a SUPERVISED FIRE ZONE and connected as shown in this manual. When Zones 1-4 are configured as a SUPERVISED FIRE ZONE, the corresponding Zone Jumpers (JP11-JP14) must be in the "SMK" (smoke) position. FIRE EMERGENCY This zone type activates the fire alarm for a normally closed (open for alarm) and open collector (short to ground for alarm) switches. It is not supervised as required for UL Listed Installations and shall NOT be used in such installations. GAS This GAS ZONE will generate an alarm, activate the sounder (on - off - on - long off), and make a dial out. This zone type requires an external 1000-ohm end-of-line resistor. When Zones 1-4 are configured as a GAS ZONE, the corresponding Zone Jumpers (JP11-JP14) must be in the "SMK" (smoke) position. AUXILIARY EMERGENCY This AUXILIARY EMERGENCY ZONE type will generate an alarm (console beeper - no sirens) and make an emergency dial out when the zone is violated. An emergency dial out is activated after the DIAL OUT DELAY. TROUBLE This zone type can be used to monitor the status of an external device, such as the battery status of a wireless security receiver. It can also used to record events in the event log (i.e. driveway activation, opening of a gate, etc.) without setting off the alarm. When the zone is tripped, the zone name will be displayed on the display as "NOT RDY". The alarm is not activated, regardless of the security mode. The trouble is logged in the event log. The digital communicator (if used) will report the alarm code for the zone. The voice dialer will not be activated. FREEZE This FREEZE ALARM ZONE type will generate an alarm (console beeper, no sirens) and make an emergency dial out. WATER This WATER ALARM ZONE type will generate an alarm (console beeper, no sirens) and make an emergency dial out. FIRE TAMPER This zone type is used to monitor the wiring to bells and sirens (other than those connected to the Horn Output). The zone will report trouble if an open, short, or other wiring problem is detected in the supervised bell circuit. This zone will make a digital dial out when violated. Connect a wire from the Fire Tamper zone (+) to an output configured as a Sounder. Page 40 AUXILIARY A zone defined as AUXILIARY is ignored for security. It is used to activate macros or to conditionalize programs. This is the default setting for all zones. Zones that are not in use should be configured as AUXILIARY. KEYSWITCH INPUT This zone is used to arm AWAY and Disarm the OmniPro II security system using a toggle (to ground) keyswitch or keypad. PROGRAMMABLE ENERGY SAVER MODULE This zone type is for use with the Programmable Energy Saver Modules (PESM). It converts the Zone and the corresponding Output to operate the PESM. Only Zones 9-16 can be programmed as a PESM. OUTDOOR TEMPERATURE AND ER OUTDOOR TEMPERATURE Use this zone type for Outdoor Temperature Sensors. The outdoor temperature can be displayed on the console, spoken over the telephone, or displayed on an HAI Communicating Thermostat. TEMPERATURE AND EXTENDED RANGE TERMPERATURE The general-purpose TEMPERATURE ZONE type is typically used to monitor indoor temperatures and control devices. It sets the zone secure/not ready state for program conditionals and event button activation programs. If FREEZE ALARM is enabled, it reports a potential freeze condition if the temperature falls below 40o. TEMPERATURE ALARM AND EXTENDED RANGE TEMPERATURE ALARM The TEMPERATURE ALARM ZONE type will generate an alarm (console beeper, no sirens) and dial out if the temperature goes above the high setpoint or drops below the low setpoint. HUMIDITY The HUMIDITY ZONE type is used to monitor indoor and outdoor humidity levels from 0 to 100 percent using the Model 31A00-2 Indoor/Outdoor Temperature and Humidity Sensor. It sets the zone secure/not ready state for program conditionals and event button activation programs. NOTE ON TEMPERATURE AND HUMIDITY ZONE TYPES Outdoor temperature, temperature, and temperature alarm zone types all have HEAT (LOW) and COOL (HIGH) setpoints. The zone is "Not Ready" when the temperature is above the high setpoint or below the low setpoint. The zone is "Secure" when the temperature is between the setpoints. Setting a setpoint to 0 disables the setpoint. Except for a type 83 and 87, the alarm is not activated. The zone "Not Ready" or "Secure" status is used to activate button programs and program conditionals. Page 41 SETUP DIGITAL COMMUNICATOR To setup the Digital Communicator, from the Installer Setup menu, select the 3 (DCM) key. FIRST PHONE NUMBER, FIRST ACCOUNT NUMBER The first item in the DIGITAL COMMUNICATOR category is the FIRST PHONE NUMBER. Enter the FIRST PHONE NUMBER on the keypad. This enables the Digital Communicator. You can cause a 2-second pause during dialing by pressing the DAY key. To prevent a call waiting line from interfering with the dial out, you may use the call waiting cancel sequence at the beginning of the number. The call waiting sequence is typically ' * 7 0 T ' (T = pause); however this may vary depending on your region. If you are using the call waiting sequence, only use it on the “FIRST PHONE NUMBER”; do not use it on the “SECOND PHONE NUMBER”. FIRST PHONE NUMBER: - ↓ To disable the digital communicator, enter a single "-" for the FIRST and SECOND PHONE NUMBER by pressing the OFF key, then ' # '. Phone number may be up to 24 digits long. Press the down arrow (Ø) to advance to the FIRST ACCT NUMBER: FIRST ACCT NUMBER: 0-FFFF 0000 Enter the 4 digit account number (3 digits if using 3/1 format) and press ' # '. To enter the digits B-F, first press the OFF key, then press the 1-5 key respectively (i.e. 1B11 = 1 OFF 1 1 1 #). NOTE: You must enter 4 digits for the account number if you are using 4/2 format (i.e. 0123), and 3 digits if using 3/1 (i.e. 123). SECOND PHONE NUMBER, SECOND ACCOUNT NUMBER Enter these if used. Note: do not use the call waiting sequence on the “SECOND PHONE NUMBER”. SECOND PHONE NUMBER: SECOND ACCT NUMBER: 0000 0-9999 COMMUNICATOR TYPE This item is used to select the transmitting parameters of the digital communicator. The OmniPro II can transmit in FAST 2300 Hz (20 PPS) mode, in SLOW 1400 Hz (10 PPS) 3/1 format, and in Contact ID. COMMUNICATOR TYPE: 0=2300 1=1400 2=ID 2 The default setting is 2 = ID (Contact ID). If you need to transmit to a 4/2 or 3/1 receiver, select the proper handshaking frequency (2300 Hz or 1400 Hz) and press ' # '. TWO-WAY AUDIO If a Two-Way Audio Module is being used, this item enables hands free audio communication between your customer's premises and the central station. Page 42 After the transmission of the alarm to the central station, the operator can talk and listen to people and sounds at the premises. TWO-WAY AUDIO: 0=NO 1=YES 0 If a Two-Way Audio Module is part of the system, select the 1 (YES) key to enable this feature. REPORT OPEN/CLOSE The communicator can be setup to send an opening and a closing report by user code. Whenever the system is disarmed the communicator will send an opening report to the central station. When the system is armed, the communicator will send a closing report to the central station. REPORT OPEN/CLOSE: 0=NO 1=YES 0 To enable the communicator to send opening and closing reports to the central station, select the 1 (YES) key. REPORT BYPASS / RESTORE This item is used to enable/disable reporting to the central station when a zone is bypassed or restored when using Contact ID. The communicator can be configured to send bypass/restore signals to the central station when using Contact ID. Whenever a zone is bypassed, the communicator will send a zone bypassed report to the central station. When a zone is restored, the communicator will send a zone restored report to the central station. REPORT BYPASS/REST: 0=NO 1=YES 1 To disable the communicator from sending bypass and restore reports to the central station, select the 0 (NO) key. AUTOMATIC TEST TIME The communicator CAN be setup to automatically send a test code to the central station on a periodic basis. AUTOMATIC TEST TIME is used to set the time and days of the week of the test, and the TEST CODE specifies the code that will be transmitted for the test. AUTOMATIC TEST TIME: -NEVER #=CHNG To disable the automatic test, press the ' # ' key and then 0 for Never, and ' # '. TEST CODE: 0-FF 98 ALARM CODES (4/2 and 3/1 Formats) Press the down arrow (Ø) to advance to the next ZONE ALARM CODE. Press the up arrow (×) to go to the previous ZONE ALARM CODE. To change an alarm code, enter two digits for 4/2 format, or one digit when using 3/1 format, then press the ' # ' key. Enter the 2 digit alarm code (1 digits if using 3/1 format) and press ' # '. To enter the digits B-F, first press the OFF key, then press the 1-5 key respectively (i.e. B1 = OFF 1 1 # and CB = OFF 2 OFF 1 #). The various alarm codes are sent when the indicated alarm zone is tripped. Each alarm code must be two digits long for 4/2 format (01-FF), 1 digit for 3/1 format (1-F). To disable the digital communicator for a specific zone, set the alarm code to 0 or 00. The digital dialer will not report when this zone is tripped. Page 43 ZONE 1 ALARM CODE: 0-FF 01 THROUGH USER 16 CLOSE CODE: 76 ↑ 0-FF SETUP AREAS To configure the system for multiple areas, from the Installer Setup menu, press the 4 (AREA) key. The number of areas must be specified. Also, consoles, zones, units, thermostats, and buttons must be assigned to areas. By default, the system is setup for one area. The display prompts for the number of areas that will be used: NUMBER OF AREAS: 1-8 1 If you choose 2-8, the Setup Areas menu is displayed: SETUP AREAS 1=CTRL 2=ZONES 3=BTTN ↓ 4=CONS 8=MSG 5=TEMP ↑ SETUP AREAS: CONTROL To assign control units to specific areas, from the Setup Areas menu, press the 1 (CTRL) key. Units can be setup so that they can be activated from specific areas or from all areas. Units for an entire X-10 House Code (groups of 16 unit numbers) can be assigned to specific areas. Units 257-384 (Expansion Enclosure voltage outputs) can be assigned to specific areas in groups of eight. Units 385-392 (controller voltage outputs) may be assigned individually to specified areas. Units 393-511 (flags) can be assigned to specific areas in groups of eight. X-10 UNITS UNITS 1-16 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↓ UNITS 129-144 AREAS: 1 2 3 4 5 6 7 8 0=CLR EXPANSION ENCLOSURE UNITS UNITS 17-32 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 145-160 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 257-260 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 33-48 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 161-176 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 261-264 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 49-64 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 177-192 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 265-268 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 65-80 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 193-208 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 269-272 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 81-96 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 209-224 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 273-276 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 97-112 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 225-240 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 277-280 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 113-128 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 241-256 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 280-284 AREAS: 1 2 3 4 5 6 7 8 0=CLR Page 44 UNITS 285-288 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 373-376 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 465-472 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 289-292 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 377-380 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 473-480 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 293-296 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 381-384 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 481-488 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 297-300 AREAS: 1 2 3 4 5 6 7 8 0=CLR CONTROLLER OUTPUT UNITS UNITS 489-496 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 301-304 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 385 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 497-504 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 305-308 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 386 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 505-511 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↑ UNITS 309-312 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 387 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 313-316 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 388 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 317-320 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 389 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 321-324 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 390 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 325-328 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 391 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 329-332 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 392 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 333-336 AREAS: 1 2 3 4 5 6 7 8 0=CLR FLAG UNITS UNITS 337-340 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 393-400 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 341-344 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 401-408 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 345-348 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 409-416 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 349-352 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 417-424 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 353-356 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 425-432 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 357-360 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 433-440 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 361-364 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 441-448 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 365-368 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 449-456 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 369-372 AREAS: 1 2 3 4 5 6 7 8 0=CLR UNITS 457-464 AREAS: 1 2 3 4 5 6 7 8 0=CLR Page 45 SETUP AREAS: ZONES To assign zones to areas, from the Setup Areas menu, press 2 (ZONE). Each zone must be assigned to one and only one area. ZONE 1 AREA: 1-8 1 ZONE 176 AREA 1-8 1 ↓ THROUGH ↑ SETUP AREAS: BUTTONS To assign groups of macro buttons to specific areas, from the Setup Areas menu, press the 3 (BTTN) key. Buttons can be configured so that they can only be activated from a particular area or from any area. Buttons are assigned to areas in groups of eight. BUTTONS 1-8 AREAS: 1 2 0=CLR ↓ BUTTONS 49-56 AREAS: 1 2 0=CLR BUTTONS 97-104 AREAS: 1 2 0=CLR BUTTONS 9-16 AREAS: 1 2 0=CLR BUTTONS 57-64 AREAS: 1 2 0=CLR BUTTONS 105-112 AREAS: 1 2 0=CLR BUTTONS 17-24 AREAS: 1 2 0=CLR BUTTONS 65-72 AREAS: 1 2 0=CLR BUTTONS 113-120 AREAS: 1 2 0=CLR BUTTONS 25-32 AREAS: 1 2 0=CLR BUTTONS 73-80 AREAS: 1 2 0=CLR BUTTONS 121-128 AREAS: 1 2 0=CLR ↑ BUTTONS 33-40 AREAS: 1 2 0=CLR BUTTONS 81-88 AREAS: 1 2 0=CLR BUTTONS 41-48 AREAS: 1 2 0=CLR BUTTONS 89-96 AREAS: 1 2 0=CLR SETUP AREAS: CONSOLES To assign a console to an area, from the Setup Areas menu, press the 4 (CONS) key. Each console must be assigned to one and only one area. A console may be set to global, which allows it to access areas other than its assigned area through security arming and the "go to" function. CONSOLE 1 AREA: 1-8 1 CONSOLE 1 GLOBAL: 0=NO 1=YES 1 ↓ THROUGH CONSOLE 16 AREA: 1 1-8 CONSOLE 16 GLOBAL: 0=NO 1=YES 1 ↑ Page 46 SET-UP AREAS: THERMOSTATS To assign thermostats to specific areas, from the Set-up Areas menu, press the 5 (TEMP) key. Thermostats can be set up so that they can only be controlled from a specific area or from all areas. PESMs and Temperature Sensors can only be controlled from a single area, as specified in SETUP AREAS. THERMOSTAT 1 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↓ THROUGH THERMOSTAT 64 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↑ SETUP AREAS: MESSAGES To assign messages to specific areas, from the Setup Areas menu, press the 8 (MSG) key. Messages can be setup so that they can be displayed in a specific area or in all areas. MESSAGES 1-8 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↓ MESSAGES 49-56 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 97-104 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 9-16 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 57-64 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 105-112 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 17-24 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 65-72 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 113-120 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 25-32 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 73-80 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 121-128 AREAS: 1 2 3 4 5 6 7 8 0=CLR ↑ MESSAGES 33-40 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 81-88 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 41-48 AREAS: 1 2 3 4 5 6 7 8 0=CLR MESSAGES 89-96 AREAS: 1 2 3 4 5 6 7 8 0=CLR Page 47 SETUP TEMPERATURES From the Installer Setup Menu, press the 5 (Temp) key to configure temperature options, enable and configure thermostats, and to assign Node IDs for each Z-Wave Thermostat. TEMPERATURE DISPLAY This allows you to choose between Fahrenheit and Celsius temperature format. TEMPERATURE DISPLAY: 1 1=FAHRENHEIT 2=CELSIUS ↓ THERMOSTAT TYPE If HAI thermostats are part of the system, this item specifies the thermostat type for each thermostat (this enables the thermostat). If thermostats are used, they must be configured to the applicable thermostat type. When any THERMOSTAT TYPE is changed from the default setting of "Not Used", Zone 16 and Output 8 is automatically configured for thermostats. There is no need to change the ZONE TYPE for Zone 16 or OUTPUT TYPE for Output 8. For thermostat types, the current setting is shown on the bottom line. THERMOSTAT 1 TYPE: 0 NOT USED #=CHNG THROUGH THERMOSTAT 64 TYPE: 0 NOT USED #=CHNG ↑ To enable or change a thermostat type, press the ' # ' key. Use the arrow keys to scroll through the list of thermostat types, then press ' # ' to select a new type. The display shows: SELECT TYPE: AUTO HEAT/COOL TYPE NUMBER AUTO HEAT/COOL HEAT/COOL HEAT ONLY COOL ONLY SETPOINT ONLY 1 2 3 4 5 1 ↓ DESCRIPTION Automatic changeover heat and cool thermostat Manual changeover heat and cool thermostat Heating only thermostat Cooling only thermostat Setpoint only thermostat Z-WAVE THERMOSTAT NODE ID If Z-Wave Thermostats are part of the system, the Node ID for the thermostat must be associated (mapped) with the specified thermostat address in the OmniPro II controller. TSTAT 1 NODE ID: 0-232 0 TSTAT 64 NODE ID: 0-232 0 ↑ THROUGH Enter the Node ID (0-232) for each Z-Wave thermostat followed by the ' # ' key. Enter 0 if there is no node associated to the specified thermostat. Page 48 SETUP MISCELLANEOUS To configure the miscellaneous Installer Setup items, from the Installer Setup menu, press the 6 (MISC) key. INSTALLER CODE The Installer code allows the installer access to the Installer Setup menu. The Installer code should be changed and not given to the customer. The Installer code cannot be used for remote phone access. INSTALLER CODE: 0000-9999 0000=DISABLE↓ The default setting for the Installer code is 1 1 1 1. NOTE: Remember this Installer code and do not disable. There is no way to reset or retrieve the code! If the code is forgotten or disabled, the OmniPro II controller must be sent back to the factory. Call for an RA#. ENABLE PC ACCESS This enables or disables the PC ACCESS feature. Factory default is enabled. ENABLE PC ACCESS: 0=NO 1=YES 1 PC ACCESS CODE This code allows dealers to put an access code in the system that is separate from the customer's Master code and the Installer code. Dealers can use the PC Access code to access the system by PC. The PC Access code cannot arm and disarm the system. The PC Access code is NOT programmed from the factory. To use it, set it to any code other than 0000. To disable the PC Access code, enter 0000 for the code. NOTE: This item must be enabled (by entering a code) if PC Access is will be used. PC ACCESS CODE: 0000-9999 0000=DISABLE CALL BACK PHONE NUMBER In response to a request for remote PC ACCESS using the PC ACCESS code, the system will hang up and dial this number back immediately. To program the CALLBACK PHONE NUMBER, enter the number then press ' # '. To remove the CALLBACK PHONE NUMBER, press the OFF key to enter a single "-", then press ' # '. CALL BACK PHONE NUMBER: OUTSIDE SIREN DELAY If an output is configured as an "Exterior Sounder", when the alarm is "tripped", the interior sounder is turned on first. After the OUTSIDE SIREN DELAY, the outside sounder is turned on. This feature helps reduce annoying false alarms by signaling inside the premises first. The outside siren delay is set to 15 seconds at the factory. You may change it to any value from 0 to 60 seconds. If you want the outside sounder to turn on immediately when the alarm is activated, set the delay to 0. We recommend a minimum time of 15 seconds. DIAL OUT DELAY: 0-60 SECONDS 15 Page 49 DIAL OUT DELAY The DIAL OUT DELAY is the number of seconds that the OmniPro II waits before making an emergency dial out, AFTER the alarm is "tripped" (activated by burglar or fire) to preclude an accidental activation of the alarm from calling in a false alarm. This delay is set at the factory to 30 seconds. Note: The DIAL OUT DELAY may be disabled for each individual zone (See – Zone Options). DIAL OUT DELAY: 15-45 SECONDS 30 ALARM RESET TIME The Alarm Reset Time is the time it takes before the alarm system resets itself after the alarm is tripped. ALARM RESET TIME: 6-30 MINUTES 6 To change the alarm reset time, enter a new time between 6-30 minutes, then press the ' # ' key. The default setting is 6 minutes. ARMING CONFIRMATION The Arming Confirmation is a quick pulse (squawk) given by the outside siren when the alarm system is armed into a security mode and the EXIT DELAY is expired. ARMING CONFIRMATION: 0=NO 1=YES 0 To enable the arming confirmation feature, press the 1 (YES) key, then press the ' # ' key. The default setting is 0 (NO) disabled. FIRE ALARM VERIFICATION This unit is equipped with a FIRE ALARM VERIFICATION feature. When enabled, if a zone configured as a FIRE (Type 32) or a GAS (Type 34) is activated, the system will cycle SWITCH 12V and Switched Power Outputs off for 10 seconds. The SWITCH 12V power output will then be restored, and 5 seconds later, the zones will be monitored again. If the zone is activated again within a 2-minute window, the fire alarm will be activated. If not, no fire alarm will be indicated. VERIFY FIRE ALARMS: 0=NO 1=YES 0 This feature is turned OFF by factory default. If VERIFY FIRE ALARMS is turned ON: 1) Any device (other than FIRE or GAS) connected to a SWITCH 12V Output (i.e. Glassbreak Detectors), must be connected to a zone configured as a LATCHING ZONE TYPE. 2) The following notice is required by UL: Page 50 WARNING This unit includes an alarm verification feature that will result in a delay of the system fire alarm signal from the initiating circuit. The total delay (OmniPro II controller plus detector delay) shall not exceed 60 seconds. No other initiating devices shall be connected to these circuits unless approved by the local authority having jurisdiction. Zone Circuit Control Unit Delay Detector Model/Delay Total Delay ________ : 10 seconds + ______________ = __________________ ________ : 10 seconds + ______________ = __________________ ________ : 10 seconds + ______________ = __________________ ________ : 10 seconds + ______________ = __________________ SUPERVISE INT SNDR This enables or disables supervision of the Interior Horn Output, which monitors the wiring to the connected sirens. Factory default is disabled. SUPERVISE INT SNDR: 0=NO 1=YES 0 SUPERVISE EXT SNDR This enables or disables supervision of the Exterior Horn Output, which monitors the wiring to the connected sirens. Factory default is disabled. SUPERVISE EXT SNDR: 0=NO 1=YES 0 ENABLE EMERGENCY KEYS This enables or disables the functionality of the emergency keys on the console keypad. Factory default is enabled. Select the 1 (YES) key to enable the emergency keys. Select the 2 (NO) key to disable the emergency keys. ENABLE EMERG KEYS: 0=NO 1=YES 1 TIME DISPLAY This allows you to choose between AM/PM and 24-HOUR time format. TIME DISPLAY: 1=AM/PM 2=24HR 1 DATE DISPLAY This allows you to choose between MONTH/DAY and DAY/MONTH date format. DATE DISPLAY: 1=MMDD 2=DDMM 1 AC POWER FREQUENCY Set this to the appropriate AC Powerline Frequency. AC POWER FREQUENCY: 1=60HZ 2=50HZ 1 Page 51 DEAD LINE DETECT NOTE: To disable OmniPro II from detecting a dead line, set this item to '0'; otherwise adjust only under direction of HAI. This item adjusts the threshold that is used to determine when the phone line goes dead. DEAD LINE DETECT: 0-15 0=DISABLE 8 OFF HOOK DETECT NOTE: Adjust only under direction of HAI. This item adjusts the threshold that is used to determine when the phone line is going off hook. OFF HOOK DETECT: 20-250 69 PICKUP AFTER HANGUP This item is used to disable OmniPro II from picking up the phone line after the called party hangs up the line. PICKUP AFTER HANGUP: 0=NO 1=YES 1 Currently, after the called party or the called party's answering machine hangs up the phone line, OmniPro II picks up the line and make its "Beep". If you wish to turn the Pickup After Hangup OFF, press 0 then ' # '. To turn it back On, press 1 then ' # '. The default setting for Pickup After Hangup is Yes. CLOCK ADJUSTMENT If the clock on an OmniPro II is running faster or slower than the actual time, you can have the OmniPro II automatically compensate up to 29 seconds per day. The OmniPro II will add or subtract the selected amount of time daily. CLOCK ADJUSTMENT: 30 1-59=-29 TO +29 SEC/DAY Enter 1-29 to subtract 1-29 seconds. Enter 31-59 to add 1-29 seconds. Enter 30 for no adjustment to the clock. The default setting is 30. MODEL AND SOFTWARE VERSION Next, the model number and software version for the system is displayed: HAI OMNIPRO II S/W VERSION 2.0 RESET SYSTEM EEPROM Select the 1 (YES) key to reset the EEPROM. All programs, names, and setup items will be reset. All system RAM will also be initialized and the system will restart. This option, if effect, allows the system to be restored to factory fresh configuration. RESET SYSTEM EEPROM? 0=NO 1=YES 0 Page 52 RESET SYSTEM RAM Select the 1 (YES) key to cause all of the system RAM to be reinitialized. The time, date, and event log will be cleared. Other volatile memory locations will also be reinitialized. The system RAM should only be reset if the system is acting strangely and memory corruption is suspected. Resetting the system RAM will not reset any setup items stored in EEPROM. RESET SYSTEM RAM? 0=NO 1=YES 0 ETHERNET MAC ADDRESS The Ethernet MAC Address, short for Media Access Control address, is the hardware address that uniquely identifies OmniPro II when connected to a network. ETHERNET MAC ADDRESS FF-FF-FF-FF-FF-FF ↑ SETUP EXPANSION To configure each Expansion Module that is installed on the system, from the Installer Setup menu, press the 7 (EXP) key. Expansion Modules include Hardwire Zone Expanders, ALC Interface Modules, and Serial Interface Modules. MODULE 1 TYPE The Module Type defines the function of each expansion module on the controller. Module 1 is the module with the “ADDR” jumper set to 1. Set the module type from the list below. Press ' # ' to change the module type, then use the arrow keys to select the proper module type, then press ' # ' to enter. MODULE 1 TYPE NOT USED 1 #=CHNG ↓ For example, when configuring the module for a Hardwire Expander and if the jumper on the Hardwire Expander is set to 1, set “Module 1” Type to “1” (HARDWIRE EXPNDR). MODULE TYPES NOT USED HARDWIRE EXPNDR ALC OMNI-LINK PRO-LINK UPB RADIO RA NUVO CONCERTO CENTRALITE VIZIA RF Z-WAVE HAI HI-FI NUVO ESSENTIA/SIMPLESE XANTECH NUMBER 0 1 2 3 4 5 6 7 9 10 11 13 14 DESCRIPTION No module is installed Model 10A06 Hardwire Expander installed ALC Interface Module is installed Model 10A17 Serial Interface using the Omni-Link protocol Model 10A17 Serial Interface using the Pro-Link protocol Model 10A17 Serial Interface using the UPB protocol Model 10A17 Serial Interface using the RadioRA protocol Model 10A17 Serial Interface using the NuVo Concerto protocol Model 10A17 Serial Interface using the CentraLite protocol Model 10A17 Serial Interface using the Z-Wave protocol Model 10A17 Serial Interface using the HAI Hi-Fi protocol Model 10A17 Serial Interface using the NuVo Essentia/Simplese protocol Model 10A17 Serial Interface using the Xantech protocol Notes: 1. Only 2 Model 10A06 Hardwire Expander Modules can be installed. 2. Only 2 ALC Interface Modules can be installed. 3. Only 1 Serial Interface Module can be installed. 4. The NuVo Grand Concerto, Speakercraft, or Proficient audio system can not be connected to the HAI Model 10A17 Serial Interface Module. It must be connected to the (J2 Serial - J5 Serial) built-in serial port on the OmniPro II controller. Page 53 MODULE 2 TYPE - MODULE 4 TYPE Module 2 is the module with the jumper set to 2, and so on. Set each module type from the list of “Module Types”. SERIAL 1 RATE "Serial 1 Rate" selects the baud rate used for the first built-in serial interface (J1 Serial) on the OmniPro II controller. Select the baud rate for the first built-in serial interface from the list. Use the arrow keys to select the baud rate then press the ' # ' key. BAUD RATE NUMBER 75 baud 150 baud 300 baud 600 baud 1200 baud 2400 baud 4800 baud 9600 baud 1 2 3 4 5 6 7 8 (default) SERIAL 1 FUNCTION The "Serial 1 Function" selects the communication protocol used for the first built-in serial interface (J1 Serial) on the OmniPro II controller. Select the function for the first built-in serial interface from the list. Use the arrow keys to select the function then press the ' # ' key. FUNCTION TYPES OMNI-LINK PRO-LINK UPB RADIO RA NUVO CONCERTO RUSSOUND CENTRALITE VIZIA RF Z-WAVE HAI HI-FI NUVO GRAND CONCERTO NUVO ESSENTIA/SIMPLESE XANTECH SPEAKERCRAFT PROFICIENT NUMBER 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DESCRIPTION Serial communication using the Omni-Link protocol Serial communication using the Pro-Link protocol Serial communication using the UPB protocol Serial communication using the RadioRA protocol Serial communication using the NuVo Concerto protocol Serial communication using the Russound protocol Serial communication using the CentraLite protocol Serial communication using the Z-Wave protocol Serial communication using the HAI Hi-Fi protocol Serial communication using the NuVo Grand Concerto protocol Serial communication using the NuVo Essentia/Simplese protocol Serial communication using the Xantech protocol Serial communication using the Speakercraft protocol Serial communication using the Proficient protocol Note: The NuVo Grand Concerto, Speakercraft, or Proficient audio systems can not be connected to the first built-in serial port (J1 Serial) on the OmniPro II controller. It must be connected to the (J2 Serial - J5 Serial) built-in serial port on the OmniPro II controller. SERIAL 2 - SERIAL 5 RATE "Serial 2 Rate" - “Serial 5 Rate" selects the baud rate used for the second, third, fourth, and fifth built-in serial interface ports (J2 Serial - J5 Serial, respectively) on the OmniPro II controller. Select the baud rate for the built-in serial interface from the list. SERIAL 2 FUNCTION The "Serial 2 Function" selects the communication protocol used for the second built-in serial interface ports (J2 Serial) on the OmniPro II controller. Select the function for the built-in serial interface from the list. Page 54 SERIAL 3 FUNCTION The “Serial 3 Function” by default is set to UPB to utilize HLC Lighting. When using HLC, plug the HAI Powerline Interface Module (PIM) into the third built-in serial interface (J3 Serial) on the OmniPro II controller. To change the “Serial 3 Function”, select the function for the built-in serial interface from the list. SERIAL 4 - SERIAL 5 FUNCTION The "Serial 4 Function" and "Serial 5 Function" selects the communication protocol used for the built-in serial interface ports (J4 Serial and J5 Serial, respectively) on the OmniPro II controller. Select the function for the built-in serial interface from the list. Notes about audio distribution systems: 1. OmniPro II only supports communications with one audio distribution system: HAI Hi-Fi, NuVo Concerto, NuVo Grand Concerto, NuVo Essentia/Simplese, Russound, Xantech, Speakercraft, or Proficient. Do not configure more than one audio protocol. 2. When connecting the Speakercraft audio system to the OmniPro II: a. b. c. 3. The Speakercraft RSA 1.0 MZC Control Interface Module must be used. Use the HAI Model 21A05-2 Serial PC Cable for making the connection. In order for the key presses to perform the correct operation, an MKP keypad must be assigned to address zero in each zone. When connecting the Proficient audio system to the OmniPro II: a. b. Use the HAI Model 21A05-2 Serial PC Cable for making the connection. In order for the key presses to perform the correct operation, a PMK keypad must be assigned to address zero in each zone. 4. When connecting the NuVo Concerto, NuVo Essentia, NuVo Simplese, Russound CAV or CAM, or Xantech MRC-88 audio system to the OmniPro II, use the HAI Model 36A05-4 Serial Connectivity Cable for making the connection. 5. When connecting the NuVo Grand Concerto audio system to the OmniPro II, an RS-232 Line Booster or Optical Isolator must be used. See the following Knowledge Base article for additional information and wiring diagram: http://kb.homeauto.com/default.asp?id=849&SID=&Lang=1. SERIAL 6 RATE "Serial 6 Rate" selects the baud rate used when a Serial Interface Module is added to the OmniPro II system. If a Serial Interface Module is installed, select its baud rate then press the ' # ' key. Page 55 SETUP ZONE OPTIONS Zone options are parameters that define the way that a zone functions. There are global zone options that affect all zones and there are individual zone options that affect how each individual zone functions. To configure zone options, from the Installer Setup menu, press the 8 (ZOPT) key. SWINGER SHUTDOWN NUMBER Swinger Shutdown is a false alarm prevention feature that counts the number of alarms caused by a specific zone. After a certain number of alarms caused by the same zone within the same arming period, the controller will then shutdown that zone for the remainder of that arming period. The "Swinger Shutdown Number" is the number of times that a zone may cause an alarm during the same arming period before it is shutdown. SWINGER SHUTDOWN NUM: 1-2 1 ↓ When enabled, if the Swinger Shutdown zone is violated (causes an alarm) 1 or 2 times (according to the “Swinger Shutdown Number”) within the same arming period, the controller will then shutdown and ignore that zone for the remainder of that arming period. The default setting is 1. CROSS ZONE WINDOW Cross Zoning is a feature that enforces redundant detection of devices such that two or more zones must trip within a defined period to cause an alarm. This feature is typically used when multiple devices are used to cover the same general area. The "Cross Zone Number" is the number of seconds in which a second zone must trip after a zone configured as “Cross Zoning” has been tripped in order to cause an alarm. CROSS ZONE NUMBER: 15-240 SECONDS 60 The default setting is 60 seconds. ZONE 1 OPTIONS – ZONE 176 OPTIONS Each zone has individual zone options that may be configured for Cross Zoning, Swinger Shutdown, and Dial Out Delay. ZONE 1 OPTIONS: 0-7 4 ZONE 176 OPTIONS: 0-7 4 THROUGH ↑ Enter a single value to configure the individual zone options for each zone according to the table below: Zone Options Table Zone Options Value Cross Zoning Swinger Shutdown Dial Out Delay 0 No No No 1 Yes No No 2 No Yes No 3 Yes Yes No 4 No No Yes 5 Yes No Yes 6 No Yes Yes The default value for Zone 1 Options – Zone 176 Options is 4. See the highlighted area of Zone Options Table. Page 56 7 Yes Yes Yes SIA CP-01 COMPLIANCE This control complies with the SIA CP-01 Control Panel Standard - Features for False Alarm Reduction. CP-01 is a standard sponsored by the Security Industry Association (SIA) designed with features for security systems and associated arming and disarming devices intended to reduce the incidence of false alarms. PROGRAMMABLE FEATURES SHIPPING DEFAULTS AND RECOMMENDED PROGRAMMING CP-01 PAR. # FEATURE REQUIREMENT RANGE SHIPPING DEFAULT RECOMMENDED PROGRAMMING* Exit Time (Exit Delay) 4.2.2.1 Required (programmable) For full or auto arming: 45-180 seconds 60 seconds 60 seconds Progress Annunciation - Disable (Audible Exit Delay) 4.2.2.2 Allowed Individual consoles may be disabled Enabled on all consoles Enabled on all consoles Exit Time Restart 4.2.2.3 Required Option For re-entry during exit delay Enabled Enabled Unvacated Premises 4.2.2.5 Required Option (except for remote arm) If no exit after full arm Enabled Enabled Entry Delay 4.2.3.1 Required (programmable) 30-60 seconds 30 seconds At least 30 seconds** Abort Window for Non-Fire Zones (Dial Out Delay – Zone Option) 4.2.5.1 Required Option May be disabled by zone Enabled Enabled (all zones) Abort Window Time (Dial Out Delay) 4.2.5.1 Required Option 15-45 seconds 30 seconds At least 15 seconds** Abort annunciation (Alarm Aborted) 4.2.5.1.2 Required Option Display that alarm was aborted Enabled No programming option Cancel Window (Alarm Reset Time) 4.2.5.4 Required 6-30 minutes 6 minutes At least 6 minutes Cancel annunciation (Alarm Canceled) 4.2.5.4.1 Required Option Display that alarm was canceled Enabled No programming option Duress Feature (Duress Code) 4.2.6.1 & 4.2.6.2 Allowed Option No duplicates with other user codes Disabled Disabled Cross Zoning (Cross Zoning – Zone Option) 4.3.1 Required Option May be enabled by zone Disabled Enabled and two (or more) zones programmed Programmable Cross Zoning Time (Cross Zone Window) 4.3.1 Allowed 15-120 seconds 15 seconds Time based on walk path in protected area Swinger Shutdown (Swinger Shutdown Number) 4.3.2 Required (programmable) For all non-fire zones, shut down at 1 or 2 trips One trip One trip Swinger Shutdown Disable (Swinger Shutdown – Zone Option) 4.3.2 Allowed For non-police response zones Enabled Enabled (all zones) Fire Alarm Verification 4.3.3 Required Option Depends on Sensors Disabled Enabled unless sensor can self verify Call Waiting Cancel 4.5 Required Option Depends on user phone line Disabled Enabled if user has call waiting * Programmable at installation may be subordinate to other UL requirements for the intended application. ** Combined Entry Delay and Abort Window (Dial Out Delay) should not exceed 1 minute. Minimum Equipment Requirements for a CP-01 Compliant Installation: Quantity 1 1 - 16 Description Applicable Model Numbers OmniPro II Controller Model 20A00-2, 20A00-5, 20A00-8, 20A00-21, 20A00-22 Omni Console Model 33A00-1, 33A00-4 Page 57 OMNIPRO II SPECIFICATIONS Size: Controller: 13 W x 13 H x 4.5 D Console: 4.6 W x 4.5 H x 1.2 D Weight: Controller: Console: approx. 10 lb. approx. 0.5 lb. Operating Ranges: 32 - 122 degrees F (0 - 50 degrees C) 10 - 95 % relative humidity, non-condensing Power: 120 VAC, 60 Hz, 60 watts Transformer: 24 VAC, 1.67 amps, 40 VA Battery: Rechargeable Lead-Acid, 12 volts, 7 amp-hour Device Fuse: Polyfuse: 1.35 A Horns Fuse: Polyfuse: 1.35 A Battery Fuse: Polyfuse: 4.00 A Polyfuses are permanent fuses that do not need replacement. Nominal Voltage: 10 - 13.7 VDC, 0.5 V max. peak to peak ripple Low Voltage Cut Out: approx. 9 VDC Typical Current Consumption at Nominal Voltage: Controller: 135 mA Console: backlight off - 35 mA; backlight on - 100 mA Controller Maximum Group Current Outputs: Devices: AUX 12 VDC, SWITCH 12 VDC, CONSOLE, and OUTPUTS 1 - 8: 1 A Horn: INT HORN and EXT HORN: 1 A Controller Maximum Individual Current Outputs: Devices: (Do not exceed 1 A total) AUX 12 VDC SWITCH 12 VDC CONSOLE OUTPUTS 1 - 8 1 A 1 A 1 A 100 mA For 24-Hour Battery Standby Time, the following must be observed: (See Figure 18) Controller Maximum Group Current Outputs (applies to residential and commercial): Devices: AUX 12 VDC, SWITCH 12 VDC, CONSOLE, and OUTPUTS 1 - 8: 250mA Horn: INT HORN and EXT HORN: 300mA Page 58 UNDERWRITER'S LABORATORIES (UL) INSTALLATION REQUIREMENTS The OmniPro II control units (20A00-2, -5, and -22) are suitable for household burglar and fire applications. Refer to UL1641 for installation requirements. Model 20A00-5 is also suitable for use in Commercial Burglar Alarm Applications, Central Station, Local and Police Connect. Refer to UL 681 for Installation Requirements. 1. The line carrier (X-10) operation is considered supplementary. Operation of the line carrier devices was not investigated by UL. 2. For those zones programmed as PANIC, DURESS or POLICE EMERGENCY, the initiating device shall be a UL Listed Hold Up Device switch. 3. Connections to phone circuit must be made via the supplied cable and RJ31X Jack as shown under RJ31X JACK CONNECTIONS in this manual. 4. For connection of smoke detectors to the controller, refer to requirements under FIRE ZONE HOOKUP and FIRE ZONE CONNECTIONS diagrams in this manual. 5. The controller must be configured for 24 hour Standby Time as shown under 24 HR STANDBY CONNECTIONS diagram in this manual. Maximum current ratings for 24 hours must be observed. 6. Recognized energy limited cable shall be employed, 22 AWG minimum for all connections. 7. The audible signal appliance shall be the Listed Wheelock Model MT-12/24-R Multitone Signal, rated 10.5 - 15.6 VDC, 95 dB(A) with 2 reflecting planes. The audible signal shall be mounted indoors in a central location. The audible signal appliance can be connected to either the "INT HORN" or "EXT HORN" circuits. In the case of the latter, the OUTSIDE SIREN DELAY shall be set to 0 seconds. 8. For Residential Applications, the Model 10A01-1 Enclosure shall be used. 9. For Commercial Applications, the Model 10A02-2 Commercial Enclosure shall be used. 10. For Commercial Applications, Listed Ademco AB12 Bell and housing to be used. 11. If the remote arm/disarm switch is used, it shall be the Listed Ademco Model 9789. 12. Operation of the controls with the Programmable Energy Saver Module was not conducted by UL. 13. Operation of the Model 12A00 Wireless Receiver was not verified by UL. 14. Operation of the Two-Way Audio Module was not verified by UL. 15. RS-232 and RS-485 communications were not verified by UL. 16. Refer to the OmniPro II Owner's Manual (Document No. 20R00-2) for programming requirements in UL Listed Installations. 17. For the monitoring of burglar alarm initiating devices, the zone type shall provide an audible output (i.e., not DURESS). 18. The Omni controller must be connected (when employed) to listed carbon monoxide gas detectors (i.e. Sentrol -Model 240-CO). 19. All connections to energy sensors and modules must be done to listed Class 2 circuits only. 20. The OmniPro II must be used in Residential Applications that are under a single ownership. When used in UL Listed Installations, the following items apply: 1. The "High Security Mode" must be ON. 2. The "Enable Auto Bypass" feature must be OFF. 3. The "Zone Resistors" must be YES. 4. The "Supervise Int Horn" must be YES. 5. The ENTRY DELAY SHALL NOT EXCEED 45 SECONDS for Residential Applications; 60 seconds for Commercial Applications. 6. The EXIT DELAY shall not exceed 60 seconds. 7. Double Delay and Quad Delay zone types shall not be used. 8. The BEEP ON TROUBLE feature must be ON. 9. For Residential Applications the sounding device may be mounted indoors. If, however, the sounding device is connected to the "EXT HORN" terminals of the OmniPro II, then the OUTSIDE SIREN DELAY shall be set to 0. 10. The DIAL OUT DELAY shall not exceed 30 seconds. 11. The SWINGER SHUTDOWN feature for each zone must be NO. 12. The CROSS ZONING feature for each zone must be NO. 13. The EXIT TIME RESTART feature must be NO. Installer: NAME: __________________________________ Page 59 NUMBER: _______________________________ 24-HOUR STANDBY BATTERY CAPACITY Maximum current ratings for 24-hours: Aux 12 VDC, Switch 12 VDC, Console, and Outputs 1-8: 250 mA Interior Horn and Exterior Horn: 350 mA 3M, P/N 952 SNAP CONNECTOR OVER WIRE 12" RED 12" BLACK BLACK WIRE TO RED WIRE TO + BATTERY 12V 7AH BATTERY 12V 7AH FIGURE 18 - 24-HOUR STANDBY CONNECTIONS Page 60 SMOKE DETECTOR INSTALLATION GUIDELINES 1. Ceiling mounted smoke detectors should be located in the center of the room or hall, or not less than 4 inches from any wall. When the detector is mounted on a wall, the top of the detector should be 4 to 12 inches from the ceiling. 2. Do not install smoke detectors where normal ambient temperatures are above 100 deg. F (37.8 deg. C) or below 40 deg. F (4 deg. C). Also, do not locate the detector in front of air conditioners, heating registers, or other locations where normal air circulation will keep smoke form entering the detector. 3. Additional information on Household Fire Warning is available at nominal cost from: The National Fire Protection Association, Battery March Park, Quincy, MA. 02269. Request Standard No. NFPA 72. Contact your home Insurance Company for a possible reduction of your insurance premium. 4. A smoke detector should be located between the sleeping area and the rest of the family living unit. 5. In family living units with more than one sleeping area, a smoke detector should be provided to protect each sleeping area. 6. A smoke detector should be located on each story (Refer to the diagrams below). 7. For complete details on proper location and installation of smoke detectors, refer to the instructions supplied with the smoke detector. Page 61 APPENDIX A – CONTACT ID REPORTING FORMAT ZONE TYPE TRIP TROUBLE Entry/exit (also Double & Quad) Perimeter (also Latching) Night Interior (also Latching) Away Interior (also Latching) Panic Police Emergency Silent Duress Tamper (also Latching) Fire Fire Emergency Gas Auxiliary Emergency Trouble Freeze Water Auxiliary Fire tamper Temperature Alarm 134 131 132 132 120 120 122 137 110 110 151 150 330 159 154 none 321 152 370 370 370 370 375 375 375 370 373 373 373 370 330 370 370 370 321 370 EVENT CODE DESCRIPTION Zone bypass/restore Fire zone bypass/restore Automatic communicator test Cancel User disarm/arm Programmed disarm/arm PC Access disarm/arm Quick arm Keyswitch disarm/arm Recent closing Exit error 570 571 602 406 401 403 407 408 409 459 374 Zone bypass/restore Fire bypass/restore Periodic test Cancel Open/close by user Automatic open/close Remote open/close Closing-quick arm Keyswitch open/close Recent closing Exit error SYSTEM TROUBLE CODE DESCRIPTION Battery low Fuse AC power failure Phone line dead Digital communicator Fire tamper 302 312 301 351 350 321 DESCRIPTION Entry/exit burglary Perimeter burglary Interior burglary Interior burglary Panic alarm Panic alarm Silent panic Tamper burglary Fire alarm Fire alarm Gas alarm 24 hour non-burglary System peripheral trouble Low temperature alarm Water leakage Auxiliary trouble Bell/siren #1 trouble Refrigeration alarm Low system battery Power supply overcurrent AC power loss Phone line #1 trouble Communication failure Bell/siren #1 trouble Page 62 APPENDIX B - DIGITAL COMMUNICATOR CODE SHEET INFORMATION FOR CENTRAL STATION Date: _________________________ Subscriber Name:______________________________________________________________________ Address 1: ______________________________________________________________________ Address 2: ______________________________________________________________________ City, State, Zip: ____________________________________________ Home #: _______________________ Work #: _________________ Password: ________________________________________________ Installer Name: ______________________________________________________________________ Address 1: ______________________________________________________________________ Address 2: ______________________________________________________________________ City, State, Zip: ____________________________________________ Phone #: _______________________ Beeper #: ________________ Subscriber's Notification List: 1. Name: __________________________________________________ Phone #: __________________________________________________ Relationship: __________________________________________________ 2. Name: __________________________________________________ Phone #: __________________________________________________ Relationship: __________________________________________________ 3. Name: __________________________________________________ Phone #: __________________________________________________ Relationship: __________________________________________________ Subscriber Equipment: Home Automation, Inc. - OmniPro II Notes: __________________________________________________________________________________ _________________________________________________________________________________________ _________________________________________________________________________________________ _________________________________________________________________________________________ First Phone #: ____________________________________________ First Account #: ____________________________________________ Second (Backup) Phone #: __________________________________ Second (Backup) Account #: __________________________________ Communicator Type (Contact ID, 1400 Hz, or 2300 Hz): ____________________ TWO-WAY AUDIO: _______ YES _______ NO REPORT OPEN/CLOSE: _______ YES _______ NO 24 HOUR TEST: _______ YES _______ NO TEST TIME: ________________________ Page 63 CODE ZONE DESCRIPTION ACTION TO TAKE 98 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 TEST CODE ZONE 1: ZONE 2: ZONE 3: ZONE 4: ZONE 5: ZONE 6: ZONE 7: ZONE 8: ZONE 9: ZONE 10: ZONE 11: ZONE 12: ZONE 13: ZONE 14: ZONE 15: ZONE 16: ZONE 17: ZONE 18: ZONE 19: ZONE 20: ZONE 21: ZONE 22: ZONE 23: ZONE 24: ZONE 25: ZONE 26: ZONE 27: ZONE 28: ZONE 29: ZONE 30: ZONE 31: ZONE 32: ZONE 33: ZONE 34: ZONE 35: ZONE 36: ZONE 37: ZONE 38: ZONE 39: ZONE 40: ZONE 41: ZONE 42: ZONE 43: ZONE 44: ZONE 45: ZONE 46: ZONE 47: ZONE 48: ZONE 49: ZONE 50: ZONE 51: ZONE 52: ZONE 53: ZONE 54: ZONE 55: ZONE 56: ZONE 57: _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Page 64 CODE ZONE DESCRIPTION ACTION TO TAKE CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EB EC ED EE EF F0 F1 F2 F3 0B 0C 0D 0E 0F 1B 1C 1D 1E 1F 2B 2C 2D 2E 2F 33 34 ZONE 58: ZONE 59: ZONE 60: ZONE 61: ZONE 62: ZONE 63: ZONE 64: ZONE 65: ZONE 66: ZONE 67: ZONE 68: ZONE 69: ZONE 70: ZONE 71: ZONE 72: ZONE 73: ZONE 74: ZONE 75: ZONE 76: ZONE 77: ZONE 78: ZONE 79: ZONE 80: ZONE 81: ZONE 82: ZONE 83: ZONE 84: ZONE 85: ZONE 86: ZONE 87: ZONE 88: ZONE 89: ZONE 90: ZONE 91: ZONE 92: ZONE 93: ZONE 94: ZONE 95: ZONE 96: ZONE 97: ZONE 98: ZONE 99: ZONE 100: ZONE 101: ZONE 102: ZONE 103: ZONE 104: ZONE 105: ZONE 106: ZONE 107: ZONE 108: ZONE 109: ZONE 110: ZONE 111: ZONE 112: ZONE 113: _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Page 65 CODE ZONE DESCRIPTION ACTION TO TAKE 35 36 37 38 39 3B 3C 3D 3E 3F 4B 4C 4D 4E 4F 57 58 58 5B 5C 5D 5E 5F 6B 6C 6D 6E 6F 77 78 79 7B 7C 7D 7E 7F 80 88 89 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 9B 9C 9D 9E 9F F4 ZONE 114: ZONE 115: ZONE 116: ZONE 117: ZONE 118: ZONE 119: ZONE 120: ZONE 121: ZONE 122: ZONE 123: ZONE 124: ZONE 125: ZONE 126: ZONE 127: ZONE 128: ZONE 129: ZONE 130: ZONE 131: ZONE 132: ZONE 133: ZONE 134: ZONE 135: ZONE 136: ZONE 137: ZONE 138: ZONE 139: ZONE 140: ZONE 141: ZONE 142: ZONE 143: ZONE 144: ZONE 145: ZONE 146: ZONE 147: ZONE 148: ZONE 149: ZONE 150: ZONE 151: ZONE 152: ZONE 153: ZONE 154: ZONE 155: ZONE 156: ZONE 157: ZONE 158: ZONE 159: ZONE 160: ZONE 161: ZONE 162: ZONE 163: ZONE 164: ZONE 165: ZONE 166: ZONE 167: ZONE 168: ZONE 169: ZONE 170: ZONE 171: _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Page 66 CODE ZONE DESCRIPTION ACTION TO TAKE F5 F6 F7 F8 F9 81 82 83 84 85 86 87 99 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 ZONE 172: ZONE 173: ZONE 174: ZONE 175: ZONE 176: FREEZE ALARM FIRE EMERG POLICE EMERG AUX EMERG DURESS BATTERY LOW FIRE TROUBLE CANCEL CODE OTHER OPEN USER 1 OPEN USER 2 OPEN USER 3 OPEN USER 4 OPEN USER 5 OPEN USER 6 OPEN USER 7 OPEN USER 8 OPEN USER 9 OPEN USER 10 OPEN USER 11 OPEN USER 12 OPEN USER 13 OPEN USER 14 OPEN USER 15 OPEN USER 16 OPEN OTHER CLOSE USER 1 CLOSE USER 2 CLOSE USER 3 CLOSE USER 5 CLOSE USER 5 CLOSE USER 6 CLOSE USER 7 CLOSE USER 8 CLOSE USER 9 CLOSE USER 10 CLOSE USER 11 CLOSE USER 12 CLOSE USER 13 CLOSE USER 14 CLOSE USER 15 CLOSE USER 16 CLOSE _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Page 67 APPENDIX C - ZONE AND UNIT MAPPING ZONE Zones 1-16 Zones 17-32 Zones 33-48 Zones 49-64 Zones 65-80 Zones 81-96 Zones 97-112 Zones 113-128 Zones 129-144 Zones 145-160 Zones 161-176 DEVICE Zones 1-16 on Controller Zones 1-16 on 1st Model 10A06 Hardwire Expander Zones 1-16 on 2nd Model 10A06 Hardwire Expander Zones 1-16 on 1st Model 17A00 Expansion Enclosure Zones 1-16 on 2nd Model 17A00 Expansion Enclosure Zones 1-16 on 3rd Model 17A00 Expansion Enclosure Zones 1-16 on 4th Model 17A00 Expansion Enclosure Zones 1-16 on 5th Model 17A00 Expansion Enclosure Zones 1-16 on 6th Model 17A00 Expansion Enclosure Zones 1-16 on 7th Model 17A00 Expansion Enclosure Zones 1-16 on 8th Model 17A00 Expansion Enclosure UNITS Units 1-16 Units 17-32 Units (1-31) Units 33-48 Units 49-64 Units (33-63) Units 65-95 Units 81-96 Units (65-95) Units 97-112 Units 113-128 Units (97-127) Units 129-144 Units 145-160 Units (129-159) Units 161-176 Units 177-192 Units (161-191) Units 193-208 Units 209-224 Units (193-223) Units 225-240 Units 241-256 Units (225-255) Units 257-272 Units 273-288 Units 289-304 Units 305-320 Units 321-336 Units 337-352 Units 353-368 Units 369-384 Units 385-392 Units 393-511 MODULES / OUTPUTS / FLAGS X-10 modules 1 - 16, House Code X X-10 modules 1 - 16, House Code X+1 ALC addresses 1-31, Module 1 - Branch 1 X-10 modules 1 - 16, House Code X+2 X-10 modules 1 - 16, House Code X+3 ALC addresses 1-31, Module 1 - Branch 2 X-10 modules 1 - 16, House Code X+4 X-10 modules 1 - 16, House Code X+5 ALC addresses 1-31, Module 1 - Branch 3 X-10 modules 1 - 16, House Code X+6 X-10 modules 1 - 16, House Code X+7 ALC addresses 1-31, Module 1 - Branch 4 X-10 modules 1 - 16, House Code X+8 X-10 modules 1 - 16, House Code X+9 ALC addresses 1-31, Module 2 - Branch 1 X-10 modules 1 - 16, House Code X+10 X-10 modules 1 - 16, House Code X+11 ALC addresses 1-31, Module 2 - Branch 2 X-10 modules 1 - 16, House Code X+12 X-10 modules 1 - 16, House Code X+13 ALC addresses 1-31, Module 2 - Branch 3 X-10 modules 1 - 16, House Code X+14 X-10 modules 1 - 16, House Code X+15 ALC addresses 1-31, Module 2 - Branch 4 Outputs 1-16, 1st Model 17A00 Expansion Enclosure Outputs 1-16, 2nd Model 17A00 Expansion Enclosure Outputs 1-16, 3rd Model 17A00 Expansion Enclosure Outputs 1-16, 4th Model 17A00 Expansion Enclosure Outputs 1-16, 5th Model 17A00 Expansion Enclosure Outputs 1-16, 6th Model 17A00 Expansion Enclosure Outputs 1-16, 7th Model 17A00 Expansion Enclosure Outputs 1-16, 8th Model 17A00 Expansion Enclosure Voltage Outputs (1-8) on Controller Flags Page 68 HAI • New Orleans, LA • U S A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Mode : UseThumbs XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2007:12:13 12:53:23-06:00 Creator Tool : Acrobat PDFMaker 8.1 for Word Modify Date : 2008:07:11 09:04:48-05:00 Metadata Date : 2008:07:11 09:04:48-05:00 Producer : Acrobat Distiller 8.1.0 (Windows) Format : application/pdf Creator : Scott A. Dudoussat Title : OmniPro II Installation Manual Description : Rev. 2.16 Document ID : uuid:24cdb3e1-b8c3-4324-9be2-28e61285dab3 Instance ID : uuid:f9834e63-4589-4eec-9126-ae1e3dc5f9c4 Company : Home Automation, Inc. Part : 1 Conformance : B Page Count : 76 Page Layout : SinglePage Subject : Rev. 2.16 Author : Scott A. DudoussatEXIF Metadata provided by EXIF.tools