Panasonic CRT Television TC 14A12P 20B12

TC-20B12 to the manual 29c049cd-dbfc-4765-aad5-3de438ffb3d3

User Manual: Panasonic CRT Television TC-14A12P

Open the PDF directly: View PDF PDF.
Page Count: 42

DownloadPanasonic CRT Television TC-14A12P TC-20B12
Open PDF In BrowserView PDF
Order DCS - AGO2002 - 003 - MS

Service Manual
Color Television

TC-14A12P
TC-20B12
BR2L chassis
Specifications
TELEVISION

TC-14A12P

TC-20B12

Power source

110/220 V AC, 60 Hz automatic switch

110/220 V AC, 60 Hz automatic switch

Consumption

55 W

69 W

Antenna input jack

75 W - VHF/UHF/Cable

75 W - VHF/UHF/Cable

Color systems

NTSC/PAL-N/AUTO/PAL-M

NTSC/PAL-N/AUTO/PAL-M

Tuning system

F.S.T.

F.S.T.

Channel capability

2 to 13 (VHF)

2 to 13 (VHF)

14 to 69 (UHF)

14 to 69 (UHF)

1 to 125 (Cable)

1 to 125 (Cable)

Picture tube (visual diagonal)

33 cm

48 cm

Audio system

3 W max (RMS)

3 W max (RMS)

Video input jack

1 (back of unit)

1 (back of unit)

Dimension (width, height, depth)

370 x 349 x 374 mm

502 x 455 x 471 mm

Weight

9,6 kg

17 kg

Remote Control Transmiter:
Power Source
Infrared Length
Number of Buttons
Dimensions (W x H x D)

3V (2 AA type batteries)
9500 A (Angstron)
29 keys
(54 x 27 x 135) mm

Supplied Accessories:
• 1 Remote Control Transmitter
• 1 300Ω/75Ω Aerial Adaptor
• 2 “AA” type batteries
• 1 Internal antenna (for TC-14A12P only)

Specifications are subject to change without notice. Weight and dimensions shown are approximate.

TC-14A12P / TC-20B12

WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technician individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repared only by experienced professional technicians.
Any attempt to service or repair the product deal with in this service information by anyone could result in serious injury or death.

General Guidelines

Contents

An Isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks. It will also protect the Receiver from being
damaged by accidental shorting that may occur during servicing.
When servicing, observe the original lead dress, especially in
the high voltage circuit. Replace all damaged parts (also parts
that show signs of overheating.)
Always Replace Protective Devices, such as fishpaper, isolation
resistors and capacitors, and shields after servicing the Receiver.
Use only manufacturer’s recommended rating for fuses, circuit
breakers, etc.
High potentials are present when this Receiver is operating.
Operation of the Receiver without the rear cover introduces
danger from electrical shock. Servicing should not be performed
by anyone who is not thoroughly familiar with the necessary
precautions when servicing high-voltage equipment.
Extreme care should be practiced when Handling the Picture
Tube. Rough handling may cause it to implode due to
atmospheric pressure (14.7 lbs per sq. in). Do not sick or scratch
the glass or subject it to any undue pressure. When handling,
use safety goggles and heavy gloves for protection. Discharge
the picture tube by shorting the anode to chassis ground (not to
the cabinet or to other mounting hardware). When discharging,
connect cold ground (i.e. dag ground lead) to the anode with a
well insulated wire or use a grounding probe.
Avoid prolonged exposure at close range to unshielded areas of
the picture tube to prevent exposure to X-ray radiation.
The Test Picture Tube used for servicing the chassis at the bench
should incorporate safety glass and magnetic shielding. The
safety glass provides shieldinf for the tube viewing area against
X-ray radiation as well as implosion. The magnetic shield limits
X-ray radiation around the bell of the picture tube in addition to
restricting magnetic effects. When using a picture tube test jig
for service, ensure that the jig is capable of handling 31kV without
causing X-ray radiation.
Before returning a serviced receiver to the owner, the service
technician must thoroughly test the unit to ensure that is
completely safe to operatore. Do not use a line isolation
transformer when testing.

General Guidelines ..................................................................... 02
Operation Guide ......................................................................... 03
IC 601 - Pins and Functions ..................................................... 15
IC601 and IC451 Voltage Table ................................................ 17
IC601 - Block Diagram .............................................................. 18
General Summary .................................................................... 19
Service Adjustments and Calibrations
Service Mode .............................................................................. 20
How to operate the DAC controls ............................................. 20
EQUIPMENT REQUIRED .......................................................... 21
AGC RF CALIBRATION ............................................................. 21
BUZZ (SOUND CIRCUIT) .......................................................... 21
ANODE AND HEATER VOLTAGE CONFIRMATION ............... 21
PAL COLOR OUTPUT SIGNAL ADJUSTMENT ...................... 21
NTSC SUB-TINT CALIBRATION ............................................... 22
PROTECTION CIRCUIT (SHUTDOWN) ................................... 22
CONFIRMATION OF OPERATION ........................................... 22
WHITE QUALITY CALIBRATION .............................................. 22
VERTICAL DEFLECTION .......................................................... 22
CALIBRATION AND CONFIRMATION ...................................... 22
CRT CUT OFF CALIBRATION .................................................. 23
WHITE BALANCE CALIBRATION ............................................. 23
SUB-BRIGHTNESS CALIBRATION ........................................... 23
FOCUS CALIBRATION .............................................................. 23
COLOR PURITY ADJUSTMENT ............................................... 24
CONVERGENCE CALIBRATION ............................................... 24
EEPROM - Memory Maps ......................................................... 25
Power Source Voltages .............................................................. 25
Main Board Schematic Diagram ................................................ 26
CRT Board Schematic Diagram ................................................ 27
Main Board Conductor view ...................................................... 28
Waveform .................................................................................... 32
Parts Location ............................................................................. 35
Packing and Acessories ............................................................. 36
Replacement Mechanical Parts List .......................................... 36
Replacement Electrical Parts List .............................................. 37

-2-

Location of Controls (TC-20B12)
ENGLISH

Back view

Front view

Operation Guide

Front view

Location of Controls (TC-14A12P)

Back view

Power cable

-3-

AUDIO

Antenna
input jack

POWER

Antenna
input jack

VIDEO

Power supply
cord output

Audio/video
input jack

Audio/video
input jack

VIDEO AUDIO
FUNC TV/AV

–

+

AV/IN

POWER

Power switch

FUNC

TV/AV

VOLUME

CHANNEL

Earphone output

Remote control sensor

Audio/Video input
Power switch

(FUNC) function button

Stand by
indicator

Channel Down ( ) or Up ( ) buttons

Volume Down ( – ) or Up ( + ) buttons

Function
button

Channel buttons
( ) ( )

Volume buttons
( ) ( )

TC-14A12P / TC-20B12

TV/AV button

TV/VCR
button

Remote
control sensor

ENGLISH

REMOTE CONTROL

Operation Guide

Remote Control
Installing the Batteries
1. Remove the battery compartment cover
from the back of the remote control, by
pressing the lock down and pulling the
cover out.

1

2. Install the batteries in the compartment
(polarities (+) and (-) must be correct).

R-TUNE

MUTE

POWER

TV/VCR
CHANNEL SELECTION

TIMER
VOLUME

3. To replace, fit both cover lugs into the
compartment slots and press the lock to
close.

2

Two “AA” batteries

Battery replacement precautions

1. Batteries must be replaced as a pair.

WAKE-UP

2. Do not combine a used battery with a
new one.

CHANNEL
KEYBOARD

-4-

3. Do not mix battery types
(example: “zinc carbon” with
“alkaline”).
RECALL

PICTURE MENU

4. Do not attempt to charge, short-circuit,
disassemble, heat, or burn used
batteries.

3

PICTURE NORM
MAIN MENU AND
MENU NA
VIGA
TION
NAVIGA
VIGATION

5. Remove the batteries if the remote
control transmitter will not be used
for a long period of time.

Note:

This remote control transmitter uses two “R6” (AA) batteries.
Dispose of the batteries in the domestic trash.
DOMESTIC
TRASH

TC-14A12P / TC-20B12

Location of Controls

ENGLISH

Outdoor Antenna Connection
For proper sound and picture reception,
an outdoor antenna, a proper cable
(75 ohms coaxial cable or 300 ohms twin
cable) and an appropriate terminal
(75 ohms) are required.
Your local service representative can
help you obtain the adequate system
and accessories for antennas.
Installation procedures different from
those presented here or any
modification of existing systems or
required accessories, as well as all
expenses involved in such actions,
shall be considered as the owner’s
sole responsibility.

1. Power Switch
Press this switch to turn the unit ON. Press again to
turn it OFF.

POWER

2. Function Button
Press this button to access the PRESET menu.
Press it continuously to select a menu function, as
shown in the illustration.
To exit the PRESET menu, press the function button
continuously.

FUNC

5
CH 5

or

Operation Guide

Operation of TV Controls

Installation

(For more details, refer to PRESET menu.)
PRESET

300 ohms
twin cable

300 to
75 ohms
matching
transformer
(supplied)

75 ohms
coaxial
cable

CH SELECT

DIRECT

ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

CABLE

AUTO
OFF

V Button
3. TV/A
TV/AV
Press this button to select the desired input.

Connection
-5-

VCR
To connect a VCR, proceed as follows:
1. Connect the VCR
audio and video
output terminals to
the audio and
video input jacks,
located on the
back of the unit.
2. Press the TV/AV
button to select the
AV mode. Turn the
VCR ON.

4. Volume Buttons
Press the left or right button for the desired listening
level.

VCR back view (only for illustration purpose)
Outdoor
antenna

TV back view (only for illustration purpose)

CHANNEL

5. Channel Buttons
Press these buttons to select the desired channel.

3. Press the button
again to return to
the TV mode.

TC-14A12P / TC-20B12

NOTE:
To use the video game, connect the video game audio and video output terminals to
the audio and video input jacks on the TV.
Connection cables are not supplied.

5
2

8

4

10
3

ENGLISH

6

1

Press these buttons to adjust
the listening level.

5.

Note:
A numerical and
graphic indication will
be displayed. The
numerical indication
ranges from zero (no
sound) to 63 (maximum
level).

TV/A
V Button
TV/AV
Press this button to select TV or video input.

7
13
11

9
14

6.

Mute Button (

)

Press this button to quickly
reduce sound level. Press it
again to restore sound.
The mute indicator (red) will
be displayed.

Power Button (O stand by mode)

1.

To turn the unit ON with this button, the power switch on the TV panel must
be ON. To turn it OFF, press the button again (stand by mode). If the unit
was turned OFF with the remote control (stand by mode), it is also possible
to turn it ON by pressing either channel button.

7.

-6-

Note:
• Leaving the unit in the stand by mode will not cause any damages and
energy consumption is minimum.
• It is recommended to turn the unit OFF periodically by using the TV
power switch. When the unit is turned ON again after 30 minutes, the
demagnetization circuit of picture tube is activated.
• If the unit is to be left unused for a long period of time, turn it OFF by
using the TV power switch, disconnect the antenna and unplug the AC
power supply cord.

CHANNEL

Channel Buttons
Press these buttons to select the
programmed channels.

3.

)

Press this button to review the selected system.
Press it again to disable this function.

8.

2.

Recall Button (

T imer Button (

)

This TV can be programmed to
turn OFF after a certain period
of time.

Time indication will flash
to indicate the last three
remaining minutes prior to
turn OFF.

Press this button repeatedly for
automatic turn OFF after 30, 60
or 90 minutes, as desired.

Channel Keyboard for Direct Selection (Memory Position)
Press these buttons to select the desired channel.
To select channels with two figures, press the -/-- button and then press the
buttons corresponding to the channel number.
Example: For channel 12, press -/-- , 1 , 2
To select channels with three figures, press the buttons corresponding to
the channel number.
Note: For selecting channels with three figures, the CH SELECT
function must be in DIRECT mode, and the ANTENNA mode in
CABLE (Refer to Tuning Procedures - Channel Selection and
Antenna Mode).

Note:
• When AUTO is selected, the unit will turn OFF automatically (stand by mode) 5 minutes after the TV station
broadcast is finished.
• This function (AUTO) will not operate when the VCR (AV) mode is selected.
To cancel the TIMER (
), select “0” (zero) by pressing the TIMER button, or turn the unit OFF by using the power
switch on the TV panel.

Operation Guide

12

Volume Buttons (+, –)

TC-14A12P / TC-20B12

4.

General Operation

ENGLISH

PICTURE MENU Button

9.
PIC MENU

Press this button to select the picture menu sequentially, as shown below:

On screen

Function

DYNAMIC

For bright places. This setting selects a higher level of brightness
and contrast.

STANDARD

For places with normal levels of luminosity. This setting selects a
normal level of brightness and contrast.

SOFT

For dark places. This setting selects a reduced level of
brightness and contrast.

1. Press the WAKE-UP button.
WAKE UP

R-TUNE Button
Press this button to instantly switch between the last two channels selected.

13.

MAIN MENU

MAIN MENU Button
Press this button to access the icon menu on the screen.

WAKE-UP Button

10.

12.

Operation Guide

General Operation

General Operation

14.

Menu navigation buttons

99

2. Press the menu navigation buttons ( / ) to set the
WAKE-UP feature.

WAKE UP TIMER

OFF

WAKE UP TIMER

00:10

The time can be set in increments of 10 minutes.
3. Set the time and turn the unit OFF by using the remote
control (stand by mode).
If the unit is turned OFF with the remote control (stand by
mode) and the WAKE-UP feature set, the led on the TV
panel will flash.

99

-7-

The unit will be turned ON automatically at the selected
time.
Note:
• The WAKE-UP feature can be programmed up to
12 hours.
• When the unit is turned ON by the WAKE-UP feature, the
TIMER will be set automatically to turn it OFF in
90 minutes. Press any button to cancel the TIMER.
4. To cancel the WAKE-UP feature:
4.1 Turn the unit OFF by using the power switch on the TV
panel.
4.2 Press the menu navigation buttons ( / ) during the
WAKE-UP indication until OFF is displayed.

WAKE UP TIMER

4.3 Press the N (Picture norm) button while the WAKE-UP
mode is displayed.
90

11.

N (Picture nor
m) Button
norm)
Press this button to reset picture setting levels (color, brightness, contrast, etc.) or
sound (tone, AVL*), back to the factory preset level.
Not
e:
Note
• For this function to operate, picture and sound setting menu must be activated.
* Refer to page 22.
TC-14A12P / TC-20B12

Select
Icon

Screen
indication

PICTURE

SOUND

IDIOMA

FEATURES

PRESET

PORTUGUÊS
ESPAÑOL
ENGLISH

ENGLISH

Press

Channel Selection
Select the most familiar channel visualization pattern.
channel 02
channel 04
channel 06
channel 08
channel 10
channel 12
channel 14
channel 16
channel 18
channel 20

Press
Screen
indication
(example)

5
CH 5
PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

MENU DYNAMIC
32

COLOR

32

NTSC-TINT

32

BRIGHT

63

CONTRAST

32

SHARPNESS

BLUE BACK
TONE LOW
AVL ON

NTSC-TINT
BRIGHT

63

CONTRAST

32

SHARPNESS

COLOR TEMP. STD

VCR/GAME
CC ON MUTE

STD

IDIOMA

OFF

PORTUGUÊS

OFF

ESPAÑOL

OFF

ENGLISH

NO

5
CH 5

MENU DYNAMIC
32 COLOR

32

CHILD LOCK
CC MODE

COLOR TEMP. STD

32

CH COLOR SET

ON

BLUE BACK
TONE LOW
AVL ON

ON

CH COLOR SET

STD

CHILD LOCK

OFF

VCR/GAME

OFF

CC MODE
CC ON MUTE

OFF

LANGUAGE
PORTUGUÊS
ESPAÑOL

[

ENGLISH

PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

NO
5
CH 5

MENU DYNAMIC
32 COLOR

BLUE BACK

ON

-8-

32

NTSC-TINT

CH COLOR SET

STD

32

BRIGHT

CHILD LOCK

OFF

63

CONTRAST

VCR/GAME

32

SHARPNESS

COLOR TEMP. STD

MENU DYNAMIC
32 COLOR
32

CC MODE
CC ON MUTE

BLUE BACK

NTSC-TINT

CH COLOR SET

BRIGHT

CHILD LOCK

63

CONTRAST

VCR/GAME

32

SHARPNESS

32

COLOR TEMP. STD

MENU DYNAMIC
32 COLOR

CC MODE
CC ON MUTE

BLUE BACK

OFF

STD
OFF
OFF
OFF

BRIGHT

CHILD LOCK

OFF

63

CONTRAST

VCR/GAME

OFF

32

SHARPNESS

NO

CH COLOR SET

STD

BRIGHT

CHILD LOCK

OFF

63

CONTRAST

VCR/GAME

32

SHARPNESS

COLOR TEMP. STD

PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

ON

NTSC-TINT

32

CC ON MUTE

5
CH 5

OFF

32

CC MODE

PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

ON

32

BLUE BACK

5
CH 5

NO

STD

MENU DYNAMIC
32 COLOR

5
CH 5
PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

ON

CH COLOR SET

COLOR TEMP. STD

Channel
exhibition

Selected
channel

1

2

2

2

4

4

3

6

6

4

8

8

5

10

10

6

12

12

7

14

14

8

16

16

9

18

18

10

20

20

Program
number

Channel
exhibition

Selected
channel

1

–

–

2

2

2

3

–

–

4

4

4

5

–

–

6

6

6

7

–

–

8

8

8

9

–

–

10

10

10

Selection of channels by position
When the channel selection is in POSITION mode, the
tuned channels in AUTO TUNE mode, will be
memorized according to the program number.

NO

NTSC-TINT

CC ON MUTE

Program
number

OFF

32

CC MODE

PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

Operation Guide

Tuning Procedures

When the MAIN MENU button is pressed, the icon menu is displayed. This gives access to picture, sound, function,
language and setup icons.

OFF
OFF
NO

[

5
CH 5
PRESET
CH SELECT
DIRECT
ANTENNA
TV
AUTO TUNE
MANUAL TUNE
COLOR SYS
AUTO
FINE TUNE
SKIP
OFF

Direct Channel Selection
When the channel selection is in DIRECT mode, the
tuned channels in AUTO TUNE mode, will be
memorized according to the TV station number.

TC-14A12P / TC-20B12

Main Menu List

POWER

FUNC TV/AV

VOLUME

CHANNEL

OR
“Remote control”

Channel Selection Mode
1.

FUNC

MAIN MENU

Press the FUNC (Function)
button and select
CH SELECT
(Channel selection)
in the PRESET menu.

Press the MAIN MENU
button and by pressing
the navigation buttons,
select PRESET and then
CH SELECT (Channel
selection).

PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

POSITION
CABLE

-9FUNC

MAIN MENU

Press the FUNC (Function)
button until the setup
menu is no longer
displayed.

Press the MAIN MENU
button until the setup menu
is no longer displayed.

AUTO

CHANNEL

“Remote control”

Press the FUNC (Function)
button and select
ANTENNA in the PRESET
menu.

FUNC

CH SELECT
(Channel selection)
screen

ANTENNA screen

5
CH 5
PRESET

OFF

POSITION
CABLE

VOLUME

ANTENNA Mode

Press the MAIN MENU
button and by pressing
the navigation buttons,
select PRESET and then
ANTENNA.

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

AUTO
OFF

Press the VOLUME button
to select TV or CABLE.

2.

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

FUNC TV/AV

OR

AUTO

PRESET

3.

POWER

MAIN MENU

5
CH 5

Press the navigation
button ( / ) to select
POSITION or DIRECT.

MAIN MENU

1.
5
CH 5

After selecting CH SELECT
(Channel selection), press
the VOLUME button to
select POSITION or DIRECT.

2.

ENGLISH

MAIN MENU

Operation Guide

Tuning Procedures

Tuning Procedures

Note:
• The POSITION mode
allows you to memorize
100 positions (0 ~ 99).

The antenna mode
indicator will
change as shown.

5
CH 5
PRESET

• The DIRECT mode allows
you to memorize
125 positions (1 ~ 125).

Press the navigation
button ( / ) to select TV
or CABLE.

OFF

3.

FUNC

To restore normal
condition.

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

AUTO
OFF

Press the FUNC (Function)
button until the setup
menu is no longer
displayed.

MAIN MENU

TV

×
CABLE

To restore normal
condition.

Press the MAIN MENU
button until the setup
menu is no longer
displayed.

Channel Capability
CHANNEL CAPABILITY

TV

VHF: 2 ~ 13, UHF: 14 ~ 69

CABLE

CABLE: 1 ~125

TC-14A12P / TC-20B12

ANTENNA MODE

MAIN MENU

POWER

FUNC TV/AV

VOLUME

CHANNEL

OR

ENGLISH

Auto Tuning Mode

Manual Tuning Mode
MAIN MENU

POWER

FUNC TV/AV

VOLUME

CHANNEL

OR

“Remote control”

1.

FUNC

MAIN MENU

2.

Press the FUNC (Function)
button and select AUTO TUNE
in the PRESET menu.

Press the MAIN MENU button
and by pressing the
navigation buttons, select
PRESET and then AUTO TUNE
(Auto tuning).

Press the VOLUME
button to start auto tuning.

AUTO TUNE (Auto turning)
screen

5
CH 5

“Remote control”

1.

FUNC

PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

MAIN MENU
AUTO
OFF

Beginning of channel
searching.

5

2.

CHANNEL

Press the FUNC (Function)
button and select MANUAL
TUNE (Manual tuning) in the
PRESET menu.
Press the MAIN MENU
button and by pressing the
navigation buttons, select
PRESET and then MANUAL
TUNE (Manual tuning).

Press the CHANNEL
button ( / ) to select
the position you want
to memorize.

AUTO TUNE

- 10 -

Press the navigation button
( / ) to start auto tuning.

Optimum tuning position is
memorized
automatically.

5
CH 5
PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

3.

FUNC

MAIN MENU

Press the FUNC (Function)
button until the setup
menu is no longer
displayed.

Press the MAIN MENU
button until the setup
menu is no longer
displayed.

3.

Press the VOLUME button
to start manual tuning.
Volume ( ) searches
channels in increasing
order.
Volume ( ) searches
channels in decreasing
order.

DIRECT
TV

AUTO
OFF

Press the right or left
navigation button to
start manual tuning.

To restore normal
condition.

Button ( ) searches
channels in increasing
order.
Button ( ) searches
channels in decreasing
order.

4.

FUNC

MAIN MENU

Press the FUNC (Function)
button until the setup
menu is no longer
displayed.
Press the MAIN MENU
button until the setup
menu is no longer
displayed.

MANUAL TUNE
(Manual tuning) screen

5
CH 5
PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

AUTO
OFF

Select the desired
channel.

5
CH 5
PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

AUTO
OFF

Beginning of channel
searching.

5

MANUAL TUNE

5
CH 5
PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

Optimum tuning
position is memorized
automatically.

AUTO
OFF

To restore normal
condition.

TC-14A12P / TC-20B12

0

Operation Guide

Tuning Procedures

Tuning Procedures

MAIN MENU

POWER

FUNC TV/AV

VOLUME

CHANNEL

OR
“Remote control”
In normal reception conditions, this feature should not be used. However, in areas where reception is poor, or if
constant interference occurs, it may improve picture and sound quality.

1.

2.

CHANNEL

FUNC

MAIN MENU

Press the CHANNEL
button to select a
channel.

Press the FUNC (Function)
button and select
FINE TUNE (Fine tuning) in
the PRESET menu.

- 11 -

Press the MAIN MENU
button and by pressing the
navigation buttons, select
PRESET and then FINE TUNE
(Fine tuning).

ENGLISH

Fine Tuning Mode

Channel Skip Mode
MAIN MENU

POWER

1.

MAIN MENU

FINE TUNE (Fine tuning)
screen

5
CH 5

2.

PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

CHANNEL
DIRECT
TV

MAIN MENU

Press the MAIN MENU button
until the setup menu is no
longer displayed.

PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

OFF

Press the VOLUME button
and select ON.

Beginning of fine tuning.

DIRECT
TV

AUTO
OFF

5
CH 5
PRESET
DIRECT
TV

AUTO
OFF

OFF will change to ON.

5
CH 5
PRESET

Press the navigation button
( / ) and select ON.

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

DIRECT
TV

AUTO
ON

AFC feature is disabled.

5
CH 5
PRESET
DIRECT
TV

The “n” indicator is
displayed on the left of
channel number.

4.

FUNC

AUTO

Press the FUNC (Function)
button until the setup
menu is no longer
displayed.

To restore normal
condition.

OFF

To restore normal
condition.
Note:
To cancel fine tuning,
perform manual tuning
procedures for the
desired channel.

Press the MAIN MENU button
until the setup menu is no
longer displayed.

Note:
When SKIP is ON, the channel cannot be selected by using the channel buttons.

TC-14A12P / TC-20B12

Press the FUNC (Function)
button until the setup menu
is no longer displayed.

Press the CHANNEL
button ( / ) to select the
channel you want to skip.

SKIP screen

5
CH 5

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

MAIN MENU

FUNC

Press the MAIN MENU button
and by pressing the
navigation buttons, select
PRESET and then SKIP.

AUTO

5

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

4.

Press the FUNC (Function)
button and select SKIP in the
PRESET menu.

Select the desired
channel.

5

CHANNEL

“Remote control”
FUNC

FINE TUNE

Press the navigation ( / )
button and adjust to
improve picture quality.

VOLUME

OR

3.
Press the VOLUME button
and adjust to improve
picture quality.

3.

FUNC TV/AV

Operation Guide

Tuning Procedures

Tuning Procedures

ENGLISH

MAIN MENU

POWER

FUNC TV/AV

VOLUME

CHANNEL

Picture Menu

OR
“Remote control”

1.

FUNC

MAIN MENU

2.

Press the FUNC (Function)
button and select COLOR
SYS in the PRESET menu.

Press the MAIN MENU
button and by pressing
the navigation buttons,
select PRESET and then
COLOR SYS.

Press the VOLUME button
repeatedly to select the
desired system.

COLOR SYS screen

5
CH 5
PRESET
CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

AUTO
OFF

The color system will
change as shown:

5
CH 5
PRESET

- 12 -

CH SELECT
ANTENNA
AUTO TUNE
MANUAL TUNE
COLOR SYS
FINE TUNE
SKIP

Press the navigation button
( / ) repeatedly to
select the desired system.

DIRECT
TV

DIRECT
TV

Picture menu

AUTO

To select functions vertically or horizontally, press the navigation buttons.

OFF

AUTO

PAL-M

PAL-N

NTSC

Press

Select

3.

FUNC

MAIN MENU

Press the FUNC (Function)
button until the setup menu
is no longer displayed.

Press the MAIN MENU
button until the setup menu
is no longer displayed.

To restore normal
condition.

Item
COLOR

Effect

Indicator

Decrease Increase

NTSC-TINT
Select

Select

Select

Select

Select

Greenish Reddish

BRIGHT

CONTRAST
SHARPNESS

Darker

Brighter

Decrease Increase

Decrease Increase

COLOR TEMP
TEMP.. STD

Important Note
If picture menu is active and the N (Picture norm) button is pressed, picture settings will be reset to factory setup
levels.

TC-14A12P / TC-20B12

Supplementary Remote Control Operations

Color System Mode

Operation Guide

Tuning Procedures

Supplementary Remote Control Operations
ENGLISH

Sound Menu

Features Menu
To select functions vertically or horizontally, press the navigation buttons.

BLUE BACK (Blue screen)
When this feature is activated, the screen will turn blue if there is
no input of a TV station signal, when the signal is weak, or when
the picture is excessively snowy. To avoid excessive noise, sound
level is reduced to zero.
Press the navigation button ( / ) to select
ON Ö OFF.

Operation Guide

Supplementary Remote Control Operations

Note:
This feature should be disabled by selecting OFF in the following
situations:
1. When the program signal is weak or when the picture is
excessively snowy.
2. When reproducing a video tape in FF or REW mode.

CH COLOR SET (Individual color channel setting)
Color intensity may vary among TV stations. This feature allows
you to individually adjust color settings for each station. Press the
navigation button ( / ) to adjust as follows:

Sound Menu

HIGH

Ö LOW

Item
TONE STD
AVL ON

Select

Effect

Indicador
STD

Decrease Ö Increase

ON Ö OFF

HIGH
LOW

AVL ON

Press the navigation button ( / ) to select
ON Ö OFF.
Note:
1. When the channel is locked, the screen turns blue and sound
level is reduced to zero.
2. When the FUNC (Function) button is pressed, the indication
CHILD LOCK ON will be displayed. No setting function can be
accessed.
3. When the unit is turned ON while in a locked channel, the
indication CHILD LOCK ON will be displayed to remind you
that this feature is activated.

AVL ((Automatic
Automatic V
olume Levelling
Volume
Levelling))

VCR/GAME

This feature restricts sound volume to a preset level, when broadcast sound levels differ between programs and
commercials.

Press the navigation button ( / ) to select
ON Ö OFF.

Important Note

When this feature is ON, brightness and contrast are set to
optimum picture levels.
CC

MODE (Mode/Closed Caption)

Press the navigation button ( / ) to select an option
as shown below:

OFF

T1

Ö

C4

Ö C3

T2

TC-14A12P / TC-20B12

Ö C1 Ö C2 Ö
Õ
T4 Ö T3 Ö

Ö

If sound menu is active and the N (Picture norm) button is pressed, sound settings will be reset to factory setup
levels.

Õ

- 13 -

Select

Ö

CHILD LOCK

To select functions vertically or horizontally, press the navigation buttons.

Press

STD

Õ

Õ

ENGLISH

This feature will function only when:
1. Mode/CC feature is OFF.
2. The MUTE button ( ) is pressed on the remote control.
Press the navigation button ( / ) to select an option as shown below:

Ö
Õ

C1

Ö

C4

Ö

SIGNALS
Picture

Check
Sound

C2

Antenna location and/or connection

Ö

Õ

NO

Before you call for service, determine the symptoms and make a few simple checks, as shown below.

C3
Snowy picture

Language

Noisy sound
Antenna location and/or connection

To select functions vertically or
horizontally, press the navigation
buttons.
Multiple image

Normal sound
Electrical appliances,
lights, cars
and motorcycles

Interference

Noisy sound

IDIOMA

Volume
(check if mute control is
activated on the remote control)

PORTUGUÊS
ESPAÑOL
ENGLISH

- 14 -

Normal picture

No sound

IDIOMA
PORTUGUÊS
ESPAÑOL
ENGLISH

No picture

No sound

Check that the AC power cord is plugged into
the AC outlet.
Unit has not been turned ON.
Brightness/contrast and audio control settings
(Check by pressing the power switch.)
Color control settings

LANGUAGE
PORTUGUÊS
ESPAÑOL
ENGLISH

No color

Normal sound
Perform channel tuning procedure again.

Hotel Mode
This feature is very useful in hotels or when the owner does not want other people to change setting levels.

No video

Low sound

When activated, only CHANNEL, VOLUME, PICTURE MENU, RECALL, MUTE, TV/AV buttons will operate.
Unit was relocated while it was ON.

To activate::

To exit Hotel mode:

1. Adjust sound level.

Press the VOLUME ( ) button on the TV panel and the
TIMER button on the remote control simultaneously.

2. Press the TIMER button on the remote control and
set it to 30 minutes.

Colored blotches

Normal sound
Improper color system

3. Press and hold the RECALL button.
4. Press the CHANNEL (
panel.

) button on the TV
No color

Noisy sound

TC-14A12P / TC-20B12

cc ON MUTE (Mute/Closed Caption)

Operation Guide

Troubleshooting Chart

Supplementary Remote Control Operations

TC-14A12P / TC-20B12

IC601 (TDA9381PS/N2/3) - Pins and Functions

- 15 -

TC-14A12P / TC-20B12

IC601 - Pins and Functions
Nome

Nº

P1.3/T1
P1.6/SCL
P1.7/SDA
P2.0/TPWM
P3.0/ADC0/PWM0
P3.1/ADC1/PWM1
P3.2/ADC2/PWM2
P3.3/ADC3/PWM3
VSSC/P
P0.5
P0.6
VSSA
SECPLL
VP2
DECDIG
PH2LF
PH1LF
GND3
DECBG
AVL/EWD (1)
VDRB
VDRA
IFIN1
IFIN2
IREF
VSC
TUNERAGC
AUDEEM/SIFIN1 (1)
DECSDEM/SIFIN2 (1)
GND2
SNDPLL/SIFAGC (1)
AVL/SNDIF/REF0/
AMOUT (1)
HOUT
FBISO
AUDEXT/
QSSO/AMOUT (1)
EHTO
PLLIF
IFVO/SVO
VP1
CVBSINT
GND1
CVBS/Y
CHROMA
AUDOUT /AMOUT (1)
INSSW2
R2/VIN
G2/YIN
B2/UIN
BCLIN

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Descrição

33
34
35

port 1.3 or Counter/Timer 1 input
port 1.6 or I 2 C-bus clock line
port 1.7 or I 2 C-bus data line
port 2.0 or Tuning PWM output
port 3.0 or ADC0 input or PWM0 output
port 3.1 or ADC1 input or PWM1 output
port 3.2 or ADC2 input or PWM2 output
port 3.3 or ADC3 input or PWM3 output
digital ground for m-Controller core and periphery
port 0.5 (8 mA current sinking capability for direct drive of LEDs)
port 0.6 (8 mA current sinking capability for direct drive of LEDs)
analog ground of Teletext decoder and digital ground of TV-processor
SECAM PLL decoupling
2 nd supply voltage TV-processor (+8V)
decoupling digital supply of TV-processor
phase-2 filter
phase-1 filter
ground 3 for TV-processor
bandgap decoupling
Automatic Volume Levelling /East-West drive output
vertical drive B output
vertical drive A output
IF input 1
IF input 2
reference current input
vertical sawtooth capacitor
tuner AGC output
audio deemphasis or SIF input 1
decoupling sound demodulator or SIF input 2
ground 2 for TV processor
narrow band PLL filter /AGC sound IF
Automatic Volume Levelling / sound IF input / subcarrier reference output /AM output
(non controlled)
horizontal output
flyback input/sandcastle output
external audio input /QSS intercarrier out /AM audio output (non controlled)

36
37
38
39
40
41
42
43
44
45
46
47
48
49

EHT/overvoltage protection input
IF-PLL loop filter
IF video output / selected CVBS output
main supply voltage TV-processor (+8 V)
internal CVBS input
ground 1 for TV-processor
external CVBS/Y input
chrominance input (SVHS)
audio output /AM audio output (volume controlled)
2 nd RGB / YUV insertion input
2 nd R input / V (R-Y) input
2 nd G input / Y input
2 nd B input / U (B-Y) input
beam current limiter input / (V-guard input, note 2)
- 16 -

TC-14A12P / TC-20B12

IC601 - Pins and Functions
Nome

Nº

BLKIN
RO
GO
BO
VDDA
VPE
VDDC
OSCGND
XTALIN
XTALOUT
RESET
VDDP
P1.0/INT1
P1.1/T0
P1.2/INT0

Descrição

50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

black current input / (V-guard input, note 2)
Red output
Green output
Blue output
analog supply of Teletext decoder and digital supply of TV-processor (3.3 V)
OTP Programming Voltage
digital supply to core (3.3 V)
oscillator ground supply
crystal oscillator input
crystal oscillator output
reset
digital supply to periphery (+3.3 V)
port 1.0 or external interrupt 1 input
port 1.1 or Counter/Timer 0 input
port 1.2 or external interrupt 0 input

IC601 / IC451 - Voltage Table
IC601
POWER ON
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

IC451
STAND-BY

Voltage

Pin

Voltage

Pin

Voltage

3,2V
NC
NC
3,3V
0V
3,3V
3,3V
3,3V
0V
0V
2,2V
0V
2,3V
7,8V
4,9V
3,4V
3,7V
0V
4V
0V
2,1V
2,2V
1,8V
1,8V
3,8V
4,4V
4,1V
3,2V
2,3V
0V
2,3V
2,5V

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

0,6V
0,8V
3,8V
4,4V
2,8V
3,2V
7,8V
4,5V
0V
4,5V
0V
3,5V
0V
0V
0V
0V
2,5V
5,3V
3,4V
3,3V
3,3V
3,3V
0V
3,3V
0V
nc
nc
nc
3,3V
0V
1,6V
4,6V

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

0V
4,8V
4,8V
0V
4,8V
3,3V
3,3V
3,3V
0V
0V
4,6V
0V
1,7V
5,1V
3,4V
1,7V
1,7V
0V
3,2V
0,3V
1,3V
1,1V
1,6V
1,6V
2,5V
2,2V
4V
1,8V
0,9V
0V
1V
1,1V

Pin

Pin

Voltage

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

0,9V
0V
1,9V
3,3V
2,2V
3,2V
5V
2,7V
0V
2,4V
0V
2,2V
0V
0V
0V
0V
2V
3,3V
0,8V
0,8V
0,9V
3,3V
0V
3,3V
0V
1,6V
1,6V
0V
3,3V
0V
0V
4,8
- 17 -

1
2
3
4
5
6
7

Voltage
3,2V
NC
NC
3,3V
0V
3,3V
3,3V

TC-14A12P / TC-20B12

IC601 - Block Diagram

- 18 -

TC-14A12P / TC-20B12

General Summary

CONFIGURATION
COLOUR SYSTEM

PAL-M / NTSC / PAL-N (PAL-M 50Hz)

POWER SOURCE

CA Automatic Voltage Selection 110 - 240V AC, 60Hz

MEMORY

100 positions

TUNING RANGE

181 channels

On Screen Display Language

English / Spanish / Portuguese

Áudio System

Mono

Vertical Magnetic Field

-0.1 ±0.03 (BRASIL)

Colour Temperature

TC-14A12P: (High Light) x= 0.260±0.01, y=0.265 ±0.01, Y=300 (nit)
(Low Light) x= 0.243±0.01, y=0.255 ±0.01, Y=6.5 (nit)
TC-20B12:

Contents
+B Voltage

Buzz

(High Light) x= 0.270±0.01, y=0.275 ±0.01, Y=155 (nit)
(Low Light) x= 0.245±0.01, y=0.235 ±0.01, Y=7.0 (nit)

Adjustment
Point

Specifications

Reference

Test Point

002

TPA 12

TC-14A12P
140.5 ± 1.5 (V)

TC-20B12
140.5 ± 1.5 (V)

TPA 11

8 ± 1 (V)

8 ± 1 (V)

TPA 10

5± 1 (V)

5± 1 (V)

TPA21

215 ± 15 (V)

215 ± 15 (V)

A22-2

0.5 (Vp-p)

0.5 (Vp-p)

007

or PA41
PAL colour sign optput

009

TPL2

D

2.45 ± 0.1 (Vo-p)

2.45 ± 0.1 (Vo-p)

TPL1

C

2.45 ± 0.5 (Vo-p)

2.45 ± 0.5 (Vo-p)

C

1.2 ± 0.5 (Vo-p)

1.2 ± 0.5 (Vo-p)

NTSC colour sign output

010

TPL1

Anode (EHT) voltage

008

CRT

24.5 +0.7 (Kv)

26.5 +0.7 (Kv)

anode

24.5 – 1.5 (kV)

26.5 – 1.5 (kV)

- 19 -

TC-14A12P / TC-20B12

Service Adjustments and Calibrations
TO EXIT SERVICE MODE AND RETURN TO THE NORMAL
STATE:

TO ENTER IN THE SERVICE MODE:
1. Adjust the volume for the minimum.
2. Adjustment the “OFF TIMER” function for 30 minutes.
3. Simultaneously press the “RECALL“ button of the remote
control unit and the “VOLUME DOWN“ button on the TV set.
After some seconds, the TV enters the SERVICE MODE and
the “CHK1” expression should appear on the screen.

Press the “NORMAL” key on the remote control unit or turn off
the unit.

HOW TO OPERATE THE “DAC” CONTROLS IN THE BR3L CHASSIS
CHK1←→CHK2
↑
↑
↓
↓
CHK4←→CHK3

To change from “CHK1” to “CHK2” mode and following, press
“2” to move forward and “1” to go back.

ADJUSTMENTS IN THE CHK1 MODE:

ADJUSTMENTS IN THE CHK2 MODE:

CHK1 OPTIONS

CHK2 OPTIONS

OPTIONS

1
2
3
4
5
6
7
8

OPTIONS

PAR

C
0
0
3
8
0
0
0

RF-AGC
CONTRAST
COLOUR
SUB-COLOUR
NTSC-TINT
SUB-NTSC-TINT
BRIGHT

1
0
0
3
0
0
0
0

PAR

31
63
32
32
32
30
32

ADJUSTMENTS IN THE CHK3 MODE:

ADJUSTMENTS IN THE CHK4 MODE:

CHK3 OPTIONS

CHK4 OPTIONS

OPTIONS

V-SLOPE
V-SHIFT 50Hz
V-SHIFT 60Hz
V-AMP 50Hz
V-AMP 60Hz
H-SHIFT
S-CORR 50Hz
S-CORR 60HZ
V-ZOOM 50 Hz
V-ZOOM 60 Hz
OSD H-POS
OSD V-POS 50 Hz
OSD V-POS 60 Hz

PAR

OPTIONS

37
2
1
16
16
36
18
18
5
7
3
28
21

R-CUT
G-CUT
BRIGHT
SUB-BRIGHT
CONTRAST
SUB-CONTRAST
R-DR
G-DR
B-DR
RGB CONTRAST

PAR

31
32
32
31
63
21
19
31
38
6

NOTE:
• To select the options, press “4” to move forward and “ 3 “ to
go back.
• Select the option and make the adjustment pressing the
“VOL_” or “ VOL+” keys.
• To memorize the adjustment press “0” (CHK1 mode only).

• To turn off AKB (blue OSD), press “5”. To turn on AKB (white OSD), press “5” of the remote control unit.
• After end of the adjustments, press the “NORMAL” key “ or turn of the unit to return to the normal mode of TV.
• To do data memory maintenance, simultaneously press “ MUTE” on the remote control and “VOL_” on the TV set when it is in
SERVICE MODE . To select the memory address, press “4” to move forward or “3” to go back.)

- 20 -

TC-14A12P / TC-20B12

Service Adjustments and Calibrations
TEST EQUIPMENT

ANODE AND HEATER VOLTAGE CONFIRMATION

To do all of these electrical adjustments, the following equipment
is required:
• Dual-Trace Oscilloscope
Voltage Range: 0.001 V to 50 V/Div.
Frequency Range: DC to 50 MHz
Probes: 10:1, 1:1
• NTSC Video Pattern Generator
• DVM (Digital Volt Meter)
• MTS/SAP Signal Generator
• (TV Multi-Channel Sound Modulator (U.S.A.))
• Plastic Tip Driver and Non-Metal Driver
• Isolation Transformer (Variable)
• Degaussing Coil
• White Pattern Generator
• Audio Generator

1. PREPARATION:
1.1. Receive a crosshatch pattern.
2.2. Adjust the bunch current in zero. (0 beam)
3.3. Adjust “SCREEN VR” and “CONTRAST” to minimum.

2. CONFIRMATION:
2.1. Connect a voltage meter between TPA12 and ground. Confirm
that the voltage +B is within a range of 140.5V± 1.5V
2.2. Connect a high frequency voltage meter (VRMS.) among the
heater, and confirm that the reads tension is within a range of 6.3
± 0.24 (VRMS)
2.3. Connect the high voltage meter in the CRT anode pin, and
confirm that the high voltage is within a range of [A]:
• TC-14A12P [A]=24.5 +0.7kV _1.5kV
• TC-20B12 [A]=26.5 +0.7kV _1.5kV

AGC RF CALIBRATION

PAL COLOR OUTPUT SIGNAL ADJUSTMENT

1. PREPARATION:
1.1. Receive a color bar pattern and assure a RF input signal of
75Ω opened, channel 13 (211.25 MHz).
1.2. Connect the digital multimeter in TPA 15.

1. PREPARATION:
1.1. Receive a color bar pattern and adjust the local frequency.
1.2. Adjust “IMAGE” to DYNAMIC NORMAL, “CONTRAST” to 63
and “SUB-CONTRAST” to 21.
1.3. Adjust the “COLOR FOR CHANNEL” level to NORMAL.
1.4. Set the CHK2 service mode option, press “5” on the remote
control unit and confirm that OSD becomes blue (AKB turned off).
1.5. Connect a short circuit jumper between TPA10 and TPA20.
1.6. Adjust [A] for 2.3 ± 0.2V through the BRIGHT control variation
in the test point TPL2.
1.7. Fix G-DRIVE GAIN, R-DRIVE GAIN and B-DRIVE GAIN data
in 1FH or 31 DAC.

2. CALIBRATION:
2.1. Select the option “RF AGC” in the “CHK2” service mode.
2.2. Adjust RF AGC to 2.2±0.1V in TPA20.
3.3. Increase the input level by +2 dB and confirm that the voltage
decrease.
Tuner

ENV56D75G3R

TEDH9-301A

Level

69dB mV

69dB mV

VIF DETECTOR OUTPUT LEVEL CONFIRMATION
1. CALIBRATION:
1.1. Install the chassis in the VIF calibration JIG and receive a
color bar pattern with 63 dBU (75Ω opened).
1.2. Connect the oscilloscope to TPA33.
1.3. Confirm that the video output signal is within a range of 1.05
± 0.15 Vp-p in TPA33.

2. CALIBRATION:
2.1. Connect the oscilloscope in TPL2 (G-OUT) with a 10KΩ
resistor and adjust “CONTRAST”, so that the waveform in [B] it is
of 2.6±0.1V according to fig. 1.
2. Adjust “SUB-COLOR” to obtain 2,45±0.1V in [D] according to
fig. 1.
3. Connect the oscilloscope in TPL1 (R-OUT) a 10KΩ resistor in
and confirm that the waveform in [C] it is of 2.45±0.1V according
to fig. 2.
4. Remove the jumper between TPA10 and TPA20, press “5” and
confirm that OSD becomes white (AKB turned on).

BUZZ (SOUND CIRCUIT)
B

1. PREPARATION:
1.1. Connect the oscilloscope with a 7kHz filter between TPA41
and ground or between the speaker’s terminals
1.2. Adjust the sound volume to the maximum.
1.3. Set “TONE” to “NORMAL” and “AVL” turned off.

A=2.3±0.2Vp-p

Fig. 1
2. CONFIRMATION:
2.1. Receive a color bar pattern channel 2, with local frequency
adjusted and the AFC turned on (Channel with sound bearer and
without modulation).
2.2. Assure that the width in the buzzing waveform is smaller than
500 m Vp-p.

C

A=2.3±0.2Vp-p

Fig. 2
- 21 -

D

TC-14A12P / TC-20B12

Service Adjustments and Calibrations
NTSC SUB-TINT CALIBRATION

WHITE QUALITY CALIBRATION

1. PREPARATION:
1.1. Connect the oscilloscope to TPL1 (R OUT) in serie with a
10KΩ resistor.
1.2. Receive a rainbow pattern through VIDEO IN.
1.3. Adjust “IMAGE” to DYNAMIC NORMAL.
1.4. Adjust “COLOR FOR CHANNEL” to NORMAL.
1.5. Set the CHK2 service mode option, press “5” on the remote
control unit and confirm that OSD becomes blue (AKB turned off).
1.6. Connect a short circuit jumper between TPA10 and TPA20.

1. PREPARATION:
1.1. Adjust the HELMHOLTZ device to local magnetic field. Horizontal: 0 ± 0.003 X 10-4T
1.2. Receive a white purity pattern.
1.3. Adjust CONTRAST and BRIGHT controls to maximum.
1.4. Previously adjust the CONVERGENCE.
1.5. Fully degauss the CRT by using an external degaussing coil.

2. CALIBRATION:
2.1. Adjust [C] for 5.0±0.2V through the BRIGHT control variation
according to fig. 1.
2.2. Adjust the NTSC SUB-TINT level according to fig. 1 positions
2, 3 and 4.
2.3. Remove the jumper , press “5” and confirm that OSD becomes
white (AKB turned on).
1 2 3 4 5 6 7 8 9 10

2. CALIBRATION:
2.1. Adjust the magnetic field in 0.4x10-4T (400 mG), and check
the white quality with the CRT turned to EAST and to WEST.
2.2. Receive a red pattern, adjust the COLOR control to maximum
and confirm the purity adjustment.
2.3. If purity error is found at the CRT corners, to apply magnetic
tapes to correct it, fully degauss the CRT again and repeat the
steps 1 and 2. Don't use this magnetic tapes on the internal side
of the yoke.
2.4. Receive a white purity pattern, adjust the COLOR control to
maximum and confirm the purity adjustment.

VERTICAL DEFLECTION
CALIBRATION AND CONFIRMATION
1. PREPARATION:
1.1. Adjust the HELMHOLTZ device to the local magnetic field
1.2. Adjust IMAGE to DYNAMIC NORMAL.

C
0V

2. CONFIRMATION AND CALIBRATION S-CORR :
• CONFIRMATION IN 50HZ
2.1. Receive a PAL-N Philips pattern
2.2. Confirm that S-CORR 50Hz is in [18] DAC.

Fig. 1
C

• CONFIRMATION IN 60HZ
2.3. Receive a monoscope pattern.
2.4. Confirm that S-CORR 60Hz is in [18] DAC.

B

2

3

4

• V-SLOPE CALIBRATION
2.5. Receive a monoscope pattern.
2.6. Adjust V_SLOPE so that the beginning of the black part of
the image be aligned with the center of the CRT as below.

A:B = 1:2

Fig. 2

PROTECTION CIRCUIT (SHUTDOWN)
CONFIRMATION OF OPERATION
1. PREPARATION:
1.1. Receive a crosshatch pattern.
1.2. Adjust CONTRAST and BRIGHT controls to minimum.

CRT
CENTER

2. CONFIRMATION:
2.1. Connect the voltmeter in TPA22 and confirm that the voltage
is smaller than [A].
2.2. Connect a DC source in TPA22 and confirm that the protection
circuit doesn't act when the voltage is [B].
2.3. Confirm that the protection circuit acts with smaller voltage
than [C].
Condition
A
B
C

14 inches
19,67V
20,66V
22,49V

20 inches
21,18V
22,31V
24,37V

3. VERTICAL CENTRALIZATION 50 HZ CALIBRATION
3.1. Receive a PAL-N Philips pattern
3.2 Adjust V-SHIFT 50Hz so that Philips pattern’s center it is in
the CRT center.
4. VERTICAL CENTRALIZATION 60 HZ CALIBRATION
4.1. Receive a monoscope pattern.
4.2. Adjust V-SHIFT 60Hz so that the monoscope pattern’s it is in
the CRT center

- 22 -

TC-14A12P / TC-20B12

Service Adjustments and Calibrations
5. VERTICAL HEIGHT (V-AMP 50HZ) CALIBRATION
5.1. Receive a PAL-N Philips pattern.
5.2. Adjust V-AMP-50Hz so that the Philips pattern’s circle height
be the same dimension of the width.
6. VERTICAL HEIGHT (V-AMP 60HZ) CALIBRATION
6.1. Receive a monoscope pattern.
6.2. Adjust V-AMP-60Hz so that:
[C] and [D] (see below) be 1.9~2.2 (typical 2.0) for 14 inches and
1.5~2.0 for 20 inches.
[A] and [B] be 1.5~2.3 (typical 2.0) for 14 inches and 1.5~1.6 for
20 inches.
6.3. Memorize in EEPROM.
A

2. CALIBRATION:
[1] LOW LIGHT CALIBRATION
1. Adjust S-BRT, so that Y = Y(L).
2. Adjust R-CUT OFF, so that x = x(L).
3. Adjust G-CUT OFF, so that y = y(L).
[2] HIGH LIGHT CALIBRATION
1. Adjust S-BRT, so that Y = Y(H).
2. Adjust R-DRIVE, so that x = x(H).
3. Adjust B-DRIVE, so that y = y(H).
[3] Repeat the procedures [1] and [2].

B

SUB-BRIGHTNESS CALIBRATION
1. PREPARATION:
1.1. Receive a windows pattern.
1.2. Position MENU OF IMAGE in DYNAMIC NORMAL.
2. CALIBRATION:
2.1. Position the color analyzer in an low light image area of CRT.
2.2. Adjust S-BRT , so that Y=5.5 ± 0.2.

C

D

SUB-CONTRAST CALIBRATION

CRT CUT OFF CALIBRATION
1. PREPARATION:
1.1. Receive a monoscope pattern.
1.2. Position DACs with the data below:
• BRT AND S-BRT = 32H.
• RGB CONTRAST = 06H for 14 inches and 07H for 20 inches.
• SUB-CONTRAST = 21H
• R,G,B DRIVE = 31H
• R,G CUT = 31H
1.3. Press “5” (AKB OFF) and confirm that OSD becomes blue.
1.4. Connect the oscilloscope in TPL7 and adjust BRT to obtain
130V in the figure below.
1.5 Adjust screen to minimum.

1. PREPARATION:
1.1. Receive a windows pattern.
1.2. Position MENU OF IMAGE in DYNAMIC NORMAL.
2. CALIBRATION:
2.1. Position the color analyzer in an hight light image area of CRT.
2. Adjust the SUB-CONTRAST , so that Y=300±10 for
14 inches and Y=160±10 for 20 inches.
3. If it is impossible to obtain the adjustment above, adjust the
SUB-CONTRAST  and confirm the SUB-BRIGHTNESS
adjustment.

FOCUS CALIBRATION
1. PREPARATION:
• Assure that the SUB-BRIGHTNESS adjustment has been
done.

130V

1.1. Receive a Philips or monoscope pattern.
1.2. Position MENU OF IMAGE in DYNAMIC NORMAL.

0V

1.6. Press “5” (AKB ON) and confirm that OSD becomes white.

2. CALIBRATION:
2.1. Adjust the FOCUS variable resistor.

WHITE BALANCE CALIBRATION
1. PREPARATION:
1.1. This adjustment should be accomplished after 30 minutes of
heating.
1.2. Receive a white balance. (This sign should contain burst sign).
1.3. Position DAC of MENU OF IMAGE for DYNAMIC NORMAL.
1.4. Fully degauss the CRT by using an external degaussing coil.
1.5. Position the color analyzer in contact with the face of CRT.

Using the Philips pattern:
• Take as reference to 3rd vertical
line.

• Assure that the CUT OFF voltage calibration has been done.
• If the value in the color analyzer is below Y(H) date, adjust
CONTRAST for 32 and connect a short circuit jumper between
TPA10 and TPA20.

1 2

- 23 -

3

3

2 1

Using the monoscope pattern:
• In the number 4
4

TC-14A12P / TC-20B12

Service Adjustments and Calibrations
COLOR PURITY ADJUSTMENT

CONVERGENCE CALIBRATION

1. Position the CRT face turned to east or west.
2. Set Bright and Contrast controls to their maximum positions.
3. Leave the set heating up for 60 minutes at white screen.
4. Fully degauss the picture tube by using an external degauss coil.
5. Apply a red pattern.
6. Loose a clamp screw for the deflection yoke and move it forward
or backward until a uniform red screen is obtained.

1. Receive a crosshatch pattern and set Contrast control to the
maximum position.
2. Adjust Bright control to obtain a clear pattern.
3. Remove the DY wedges and slightly tilt the deflection yoke to
the vertically and horizontally to obtain the good overall
convergence.
BGR
Vertical
R
G
B

B
G
R

Uniform red screen
RGB
BACKWAD

à  à

FORWARD

Horizontal

Screw for deflection yoke

CRT

4. Fix the deflection yoke by reinserting the DY wedges as showed
below.

Deflection yoke

7. Adjust rougly the Low Light controls and make sure that a uniform
white field is obtained.
8. Tighten the clamp screw.

5. If purity error is found, repeat “Color Purity” adjustment
Notes:
• Wedge A showed above should be fixed within a range of 45° to
the left of the vertical line shown.
• After inserting wedge A, insert wedges B, C and D. The wedges
should be set 90° apart from each other.
• Be certain that the four wedges are firmly fixed and the Deflection
Yoke is tightly clamped in place.
Otherwise the Deflection Yoke may shift its position and cause a
loss of convercence and purity.

- 24 -

TC-14A12P / TC-20B12

EEPROM - Memory Maps
EEPROM X’ A0’ address (0XX)
00

01

02

03

04

05

06

07

08

09

0A

0B

EEPROM X’ A4’ address (2XX)
0C

0D

0E

0F

00

01

02

03

04

05

06

07

08

09

0A

0B

0C

0D

0E

0F

00

02

00

06

01

00

06

02

00

06

03

00

06

04

00

06

05

00

02

00

A5

5A

00

01

00

00

00

08

00

04

00

00

01

00

10

00

06

06

00

06

07

00

06

08

00

06

09

00

06

0A

00

10

00

00

00

00

00

00

00

00

20

00

00

00

00

00

00

00

20

06

0B

00

06

0C

00

06

0D

00

06

0E

00

06

0F

00

06

20

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

30

10

00

06

11

00

06

12

00

06

13

00

06

14

00

06

15

30

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

40

00

06

16

00

06

17

00

06

18

00

06

19

00

06

1A

00

40

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

50

06

1B

00

06

1C

00

06

1D

00

06

1E

00

06

1F

00

06

50

20

20

20

3F

2D

20

20

20

2D

20

1E

20

20

23

20

00

60

20

00

06

21

00

06

22

00

06

23

00

06

24

00

06

25

60

00

00

01

00

00

00

00

00

00

00

00

00

00

00

00

00

70

00

00

00

00

00

00

00

00

00

00

00

00

00

00

90

D0

80

20

20

20

3F

OP

20

20

20

2D

20

1E

20

20

23

1E

01

70

00

06

26

00

06

27

00

06

28

00

06

29

00

06

2A

00

80

06

2B

00

06

2C

00

06

2D

00

06

2E

00

06

2F

00

06

90

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

A0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

90

30

00

06

31

00

06

32

00

06

33

00

06

34

00

06

35

A0

00

06

36

00

06

37

00

06

38

00

06

39

00

06

3A

00

B0

06

3B

00

06

3C

00

06

3D

00

06

3E

00

06

3F

00

06

B0

03

1C

15

00

00

00

00

00

00

00

00

00

00

00

00

00

C0

40

00

06

41

00

06

42

00

06

43

00

06

44

00

06

45

C0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

D0

00

06

46

00

06

47

00

06

48

00

06

49

00

06

4A

00

D0

0C

05

0C

04

00

00

00

00

00

00

00

00

00

00

00

00

E0

06

4B

00

06

4C

00

06

4D

00

06

4E

00

06

4F

00

06

E0

00

00

00

00

00

00

00

00

C1

00

00

33

80

00

00

01

F0

50

00

06

51

00

06

52

00

06

53

00

06

54

00

06

55

F0

00

00

18

20

15

1A

00

00

00

00

00

00

00

A5

3F

A5

0E

0F

5A

00

EEPROM X’ A2’ address (1XX)
00
00

00

01
06

02
56

03
00

04
06

05
57

06
00

07
06

08
58

09
00

0A
06

0B
59

EEPROM X’ A6’ address (3XX)
0C
00

0D
06

00

01

02

03

04

05

06

07

08

09

0A

0B

0C

0D

0E

0F

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

10

06

5B

00

06

5C

00

06

5D

00

06

5E

00

06

5F

00

06

10

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

20

60

00

06

61

00

06

62

00

06

63

00

06

64

00

06

65

20

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

30

00

06

66

00

06

67

00

06

68

00

06

69

00

06

6A

00

30

1B

20

00

22

17

1A

0F

0F

2B

24

1F

12

20

19

1F

1F

40

06

6B

00

06

6C

00

06

6D

00

06

6E

00

06

6F

00

06

40

1F

1F

1F

00

06

00

00

00

10

29

C0

00

2A

00

34

2C

50

70

00

06

71

00

06

72

00

06

73

00

06

74

00

06

75

50

30

21

02

4A

OP

44

00

00

00

00

00

00

FE

00

00

00

60

00

06

76

00

06

77

00

06

78

00

06

79

00

06

7A

00

60

02

FF

1C

12

19

00

00

00

00

00

00

00

00

00

00

00

70

06

7B

00

06

7C

00

06

7D

00

06

00

00

00

00

00

00

70

00

00

00

00

00

00

00

00

10

00

00

00

00

00

00

00

80

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

80

00

00

00

00

00

00

00

0E

11

0D

06

0C

07

0C

02

00

00

00

90

09

00

OP

00

00

00

00

0A

F8

FD

00

00

00

00

00

03

00

00

A0

01

03

02

03

03

00

34

00

00

00

2C

63

03

00

20

30

90
A0

00
06

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

00
00

B0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

B0

CA

49

4B

00

33

00

00

FF

FC

04

05

05

03

F8

OP

F2

C0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

C0

20

07

4F

40

40

00

00

00

00

00

00

00

00

00

00

00

D0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

D0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

E0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

E0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

F0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

F0

00

00

00

00

00

00

00

00

00

00

00

00

00

00

00

11

Power Source Voltages

Click here to play the Power Source Voltages presentation (MS PowerPoint is necessary)
- 25 -

TC-14A12P / TC-20B12

Main Board Schematic Diagram - TC-14A12P / TC-20B12

- 26 -

TC-14A12P / TC-20B12

CRT - Board Schematic Diagram

- 27 -

TC-14A12P / TC-20B12

Main Board Conductor View (left / component side)

6

5

4

3

2

1

A

B

C
- 28 -

D

TC-14A12P / TC-20B12

Main Board Conductor View (right / component side)

6

5

4

3

2

1

A

B

C
- 29 -

D

TC-14A12P / TC-20B12

Main Board Conductor View (left / foil side)

6

5

4

3

2

1

A

B

C
- 30 -

D

TC-14A12P / TC-20B12

Main Board Conductor View (right / foil side)

6

5

4

3

2

1

A

B

C
- 31 -

D

TC-14A12P / TC-20B12

Waveform
• All the waveforms had read with 127V power source and receiving a colorbar pattern.

IC601

Pino 21

Pino 22

Pino 33

Pino 34

Pino 38

Pino 40

- 32 -

TC-14A12P / TC-20B12

IC601

Pino 42

Pino 51

Pino 52

Pino 53

Pino SCL

Pino SDA

TNR001

- 33 -

TC-14A12P / TC-20B12

IC801

Pino 01 (tensão de rede: 127V)

IC451

Pino 01 (tensão de rede: 220V)

X101

Pino 01

Pino 02

Q501

Q551

Coletor

Coletor

- 34 -

TC-14A12P / TC-20B12

Parts Location

- 35 -

TC-14A12P / TC-20B12

Packing and Acessories
30

31
29

Replacement Mechanical Parts List
Ref.No.

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

TC-20B12
EASZ9D03A8
TSA8108-6K
S-U5012
TLK2B20001A
TBX2B864
TBX2B846-1
ESB92DA1B
TSX2B1421SB
TXAJTA22CB20A12
EVQ11G05R
A48EAK01X094R
TNQ2B2901
TBM4G3003
TMM2B202-1
TXFKY20B12
TKK2B0309
TXF3A20C7-1
TKP2B11191-2
TZGNPAL20B12
TEDH9-301A
330550044K2F
TXITKU2B21403-5
TJB16664
KFT3AA428F
------o-----TXPTKY2B1003-1
------o-----TQB2B0128
TPC2B4960
TPD2B735-1
TPE2B4016
------o------

TC-14A12P
EASZ9D03A8
TSA8108-6K
S-U5012
TLK2B14001A
TBX2B861-1
TBX2B862-1
ESB92DA1B
TSX2B1421SB
TXAJTA22CB14A12
EVQ11G05R
A34EAK01X094R
TNQ2B2901
TBM4G3008
TMM2B202-1
TXFKY14A12P
TKK2B0307
TXF3A14C7
TKP2B11221
TZGNPAL14A12P
TEDH9-301A
330620065
TXITKU2B22301-1
TJB16664
KFT2AA427F
TKP2B11161-2
TXPTKY2B1801-1
TJB4G605
TQB2B0128
TPC2B1300
TPD2B760
TPE2B4017
TMK2B720

Description
SPEAKER 16Ω, 3W
TELESCOPIC ANTENNA
75Ω ADAPTOR
DEGAUSSING COIL
6 POSITIONS BUTTON
POWER BUTTON
POWER SWITCH
AC CABLE
2 WAY CONNECTOR (SPEAKER)
SWITCHES - S1001 ~ 1006
PICTURE TUBE
REMOTE CONTROLLER
PANASONIC BADGE
AC CABLE HOLDER
ASSEMBLED CABINET
LED GUIDE
MALHA P/ ATERRAMENTO
LENS PANEL
ASSEMBLED PCB
TUNER
CRT SOCKET
REAR COVER
AV TERMINAL (JK3001)
FLY BACK
AC CABLE HOLDER ( CINZA )
CABINET
AV TERMINAL (JK3101)
OPERATING INSTRUCTIONS
PACKING CASE PAPER
FILLERS
POLY BAG
CUSHION

- 36 -

TC-14A12P / TC-20B12

Replacement Electrical Parts List
Ref. No.

TC-20B12

TC-20A12P

Description

MAIN BOARD
TZGNPAL20B12

CAPACITORS

C001
C002
C005
C006
C008
C117
C354
C355
C356
C359
C368
C370
C371
C373
C377
C401
C402
C403
C406
C408
C409
C502
C504
C506
C511
C519
C520
C552
C555
C558
C559
C560
C560
C561
C561
C562
C562
C563
C563
C565
C565
C570
C570
C601
C602
C603
C604
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C617
C618
C620
C621
C622
C623
C624
C625

ECEA1CKA220B
ECJ2VF1H104Z
ECJ2VF1H104Z
ECA1AM331B
ECEA1HKA010B
ECJ2VB1H103J
ECJ2VC1H330J
ECJ2VC1H330J
ECJ2VC1H330J
ECQM4104KZB
ECJ2VC1H561J
ECKW3D102KBP
ECEA1CN100UB
ECA2EM100B
ECA1CM221B
ECJ2VC1H222J
ECA1VM222E
ECA1HM220B
ECA1HM101B
ECQV1H274JM3
ECA1HM330B
ECKR2H821KB5
ECJ2VB1H681K
ECCR2H100D5
ECA1VM101B
ECA160V33UE
ECA0JM221B
ECA2EM100B
ECKR2H471KB5
ECA2CMR47B
ECWH16822JVB
----o---ECQM4333JZ
ECKW3D821JBN
----o---ECKW3D471JBN
----o---ECWF2394JSR
----o---ECQP1H183JZ3
----o---ECJ2VC1H560J
----o---ECEA1CKA101B
ECJ2YB1H104K
ECJ2VB1H472K
ECQV1H224JM3
ECQV1H224JM3
ECJ2VC1H222J
ECEA1HKA010B
ECEA1HKA2R2B
ECJ2YB1H104K
ECJ2VB1H103J
ECEA1HKAR22B
ECJ2VB1H472K
ECJ2VB1H472K
ECQV1H104JM3
ECQV1H224JM3
ECJ2VB1H392K
ECEA1CKA100B
ECKR1H681KB5
ECJ2VC1H470J
ECJ2VB1H471K
ECJ2VF1H104Z
ECJ2VC1H270J
ECEA1CKA100B
ECA0JM221B

TZGNPAL14A12P ASSEMBLED PCB
ECEA1CKA220B
ECJ2VF1H104Z
ECJ2VF1H104Z
ECA1AM331B
ECEA1HKA010B
ECJ2VB1H103J
ECJ2VC1H330J
ECJ2VC1H330J
ECJ2VC1H330J
ECQM4104KZB
ECJ2VC1H561J
ECKW3D102KBP
ECEA1CN100UB
ECA2EM100B
ECA1CM221B
ECJ2VC1H222J
ECA1VM222E
ECA1HM220B
ECA1HM101B
ECQV1H274JM3
ECA1HM330B
ECKR2H821KB5
ECJ2VB1H681K
ECCR2H100D5
ECA1VM101B
ECA160V33UE
ECA0JM221B
ECA2EM100B
ECKR2H471KB5
ECA2CMR47B
ECWH16822JVB
ECQM4273JZW
----o-------o---ECKD3D221JBP
----o---ECKW3D681JBN
----o---ECWF2224JBB
----o---ECQP1H223JZ3
----o---ECJ2VC1H470J
ECEA1CKA101B
ECJ2YB1H104K
ECJ2VB1H472K
ECQV1H224JM3
ECQV1H224JM3
ECJ2VC1H222J
ECEA1HKA010B
ECEA1HKA2R2B
ECJ2YB1H104K
ECJ2VB1H103J
ECEA1HKAR22B
ECJ2VB1H472K
ECJ2VB1H472K
ECQV1H104JM3
ECQV1H224JM3
ECJ2VB1H392K
ECEA1CKA100B
ECKR1H681KB5
ECJ2VC1H470J
ECJ2VB1H471K
ECJ2VF1H104Z
ECJ2VC1H270J
ECEA1CKA100B
ECA0JM221B

CAP. ELETROL. 22 µF 16,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. ELETROL. 330 µF 10,0 V
CAP. ELETROL. 1 µF 50,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. CER. SMD 33 PF 50,0 V
CAP. CER. SMD 33 PF 50,0 V
CAP. CER. SMD 33 PF 50,0 V
CAP. POLIÉSTER 100 nF 400,0 V
CAP. CER. SMD 560 PF 50,0 V
CAP. CER. 1 nF 2.000,0 V
CAP. ELETROL. BIPOLAR 10 µF 16,0 V
CAP. ELETROL. 10 µF 250,0 V
CAP. ELETROL. 220 µF 16,0 V
CAP. CER. SMD 2.200 PF 50,0 V
CAP. ELETROL. 2.200 µF 35,0 V
CAP. ELETROL. 22 µF 50,0 V
CAP. ELETROL. 100 µF 50,0 V
CAP. POLIESTER 270 nF 50,0 V
CAP. ELETROL. 33 µF 50,0 V
CAP. CER. 820 PF 500,0 V
CAP. CER. SMD 680 PF 50,0 V
CAP. CER. 10 PF 100,0 V
CAP. ELETROL. 100 µF 35,0 V
CAP. ELETROL. 33 µF 160,0 V
CAP. ELETROL. 220 µF 6,3 V
CAP. ELETROL. 10 µF 250,0 V
CAP. CER. 470 PF 500,0 V
CAP. ELETROL. 0,47 µF 160,0 V
CAP. POLYPROPYLENE . 8,20 nF 1.600 V
CAP. POLIESTER 27 nF 400,0 V
CAP. POLIESTER 33 nF 400,0 V
CAP. CER. 820 PF 2.000,0 V
CAP. CER. 220 PF 2.000,0 V
CAP. CER. 470 PF 2.000,0 V
CAP. CER. 680 PF 2.000,0 V
CAP. POLYPROPYLENE 390 nF 250,0 V
CAP. POLYPROPYLENE 220 nF 250,0 V
CAP.POLYPROPYLENE 18 nF 50,0 V
CAP.POLYPROPYLENE 22 nF 50,0 V
CAP. CER. SMD 56 PF 50,0 V
CAP. CER. SMD 47 PF 50,0 V
CAP. ELETROL. 100 µF 16,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 4.700 PF 50,0 V
CAP. POLIÉSTER 220 nF 50,0 V
CAP. POLIÉSTER 220 nF 50,0 V
CAP. CER. SMD 2.200 PF 50,0 V
CAP. ELETROL. 1 µF 50,0 V
CAP. ELETROL. 2,20 µF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. ELETROL. 0,22 µF 50,0 V
CAP. CER. SMD 4.700 PF 50,0 V
CAP. CER. SMD 4.700 PF 50,0 V
CAP. POLIÉSTER 100 nF 50,0 V
CAP. POLIÉSTER 220 nF 50,0 V
CAP. CER. SMD 3.900 PF 50,0 V
CAP. ELETROL. 10 µF 16,0 V
CAP. CER. 680 PF 50,0 V
CAP. CER. SMD 47 PF 50,0 V
CAP. CER. SMD 470 PF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 27 PF 50,0 V
CAP. ELETROL. 10 µF 16,0 V
CAP. ELETROL. 220 µF 6,3 V

Ref. No.

C627
C628
C629
C631
C633
C634
C635
C636
C639
C641
C653
C660
C801
C802
C803
C805
C806
C807
C808
C809
C811
C813
C814
C815
C817
C818
C820
C821
C824
C831
C832
C840
C841
C851
C853
C855
C856
C857
C859
C861
C861
C862
C863
C865
C866
C971
C1101
C1103
C1104
C1105
C1106
C1120
C1130
C1131
C1132
C1203
C1204
C1205
C2301
C2302
C2305
C2306
C2307
C2307
C2308
C2309
C2310
C2311
C2312
C2313

- 37 -

TC-20B12

TC-20A12P

Description

ECJ2YB1H473K
ECJ2YB1H473K
ECJ2YB1H104K
ECJ2VB1H222K
ECJ2VF1C105Z
ECJ2VF1C105Z
ECJ2VF1H104Z
ECEA1CKA101B
ECA1HM220B
ECJ2VC1H100C
ECEA1CKA100B
ECQV1H105JM3
ECKCNA331MB7
ECKCNA152ME7
ECKWAE472ZE
ECQU2A224BN9
ECKWAE472ZE
ECKWAE472ZE
ECQB1H681JM3
ECKWAE472ZE
F2A1V330A085
ECKCNA332ME7
ECKR1H471KB5
ECQB1H392JM3
ECQU2A224BN9
ECKCNA331MB7
ECKW3D122KBP
ECKD3A472KBP
F2B2G221A012
ECKR3A271KBP
F2A1C471A116
ECJ2YB1C474K
ECJ2YB1A824K
ECJ2VF1C105Z
ECKR2H151KB5
ECJ2VF1C105Z
ECKR2H151KB5
ECA1CM471B
F2A1V681A096
ECA1VM102E
ECA1VM102B
ECEA1VKA100B
ECKR2H271KB5
F2A2C680A021
ECKW3D221JBP
ECJ2VF1H103Z
ECJ2VF1H104Z
ECJ2VC1H331J
ECA1CM101B
ECJ2VF1H104Z
ECJ2VF1H104Z
ECA1HM4R7B
ECJ2VC1H560J
ECA0JM221B
ECJ2VC1H560J
ECJ2VF1H104Z
ECEA1CKA101B
ECA1CM101B
ECJ2VB1H103K
ECA1CM100B
ECA1CM100B
ECA1CM470B
ECA1VM102E
ECA1VM102B
ECJ2VF1H103Z
ECA1EM471B
ECQV1H224JM3
ECQV1H224JM3
ECA1VM470B
ECA1HM3R3B

ECJ2YB1H473K
ECJ2YB1H473K
ECJ2YB1H104K
ECJ2VB1H222K
ECJ2VF1C105Z
ECJ2VF1C105Z
ECJ2VF1H104Z
ECEA1CKA101B
ECA1HM220B
ECJ2VC1H100C
ECEA1CKA100B
ECQV1H105JM3
ECKCNA331MB7
ECKCNA152ME7
ECKWAE472ZE
ECQU2A224BN9
ECKWAE472ZE
ECKWAE472ZE
ECQB1H681JM3
ECKWAE472ZE
F2A1V330A085
ECKCNA332ME7
ECKR1H471KB5
ECQB1H392JM3
ECQU2A224BN9
ECKCNA331MB7
ECKW3D122KBP
ECKD3A472KBP
F2B2G221A012
ECKR3A271KBP
F2A1C471A116
ECJ2YB1C474K
ECJ2YB1A824K
ECJ2VF1C105Z
ECKR2H151KB5
ECJ2VF1C105Z
ECKR2H151KB5
ECA1CM471B
F2A1V681A096
ECA1VM102E
ECA1VM102B
ECEA1VKA100B
ECKR2H271KB5
F2A2C680A021
ECKW3D221JBP
ECJ2VF1H103Z
ECJ2VF1H104Z
ECJ2VC1H331J
ECA1CM101B
ECJ2VF1H104Z
ECJ2VF1H104Z
ECA1HM4R7B
ECJ2VC1H560J
ECA0JM221B
ECJ2VC1H560J
ECJ2VF1H104Z
ECEA1CKA101B
ECA1CM101B
ECJ2VB1H103K
ECA1CM100B
ECA1CM100B
ECA1CM470B
ECA1VM102E
ECA1VM102B
ECJ2VF1H103Z
ECA1EM471B
ECQV1H224JM3
ECQV1H224JM3
ECA1VM470B
ECA1HM3R3B

CAP. CER. SMD 47 nF 50,0 V
CAP. CER. SMD 47 nF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 2.200 PF 50,0 V
CAP. CER. SMD 1 µF 16,0 V
CAP. CER. SMD 1 µF 16,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. ELETROL. 100 µF 16,0 V
CAP. ELETROL. 22 µF 50,0 V
CAP. CER. SMD 10 PF 50,0 V
CAP. ELETROL. 10 µF 16,0 V
CAP. POLIÉSTER 1 µF 50,0 V
CAP. CER. 330 PF 4.000,0 V
CAP. CER. 1,50 nF 4.000,0 V
CAP. CER. 4,70 nF 250VAC
CAP. POLYPROPYLENE 220 nF 100,0 V
CAP. CER. 4,70 nF 250VAC
CAP. CER. 4,70 nF 250VAC
CAP. POLIÉSTER 680 PF 50,0 V
CAP. CER. 4,70 nF 250VAC
CAP. ELETROL. 33 µF 35,0 V
CAP. CER. 3,30 nF 4.000,0 V
CAP. CER. 470 PF 50,0 V
CAP. POLIÉSTER 3,90 nF 50,0 V
CAP. POLYPROPYLENE 220 nF 100,0 V
CAP. CER. 330 PF 4.000,0 V
CAP. CER. 1,20 nF 2.000,0 V
CAP. CER. 4,70 nF 1.000,0 V
CAP. ELETROL. 220 µF 400,0 V
CAP. CER. 270 PF 1.000,0 V
CAP. ELETROL. 470 µF 16,0 V
CAP. CER. SMD 470 nF 16,0 V
CAP. CER. SMD 820 nF 10,0 V
CAP. CER. SMD 1 µF 16,0 V
CAP. CER. 150 PF 500,0 V
CAP. CER. SMD 1 µF 16,0 V
CAP. CER. 150 PF 500,0 V
CAP. ELETROL. 470 µF 16,0 V
CAP. ELETROL. 680 µF 35,0 V
CAP. ELETROL. 1.000 µF 35,0 V
CAP. ELETROL. 1.000 µF 35,0 V
CAP. ELETROL. 10 µF 35,0 V
CAP. CER. 270 PF 500,0 V
CAP. ELETROL. 68 µF 160,0 V
CAP. CER. 220 PF 2.000,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 330 PF 50,0 V
CAP. ELETROL. 100 µF 16,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. ELETROL. 4,70 µF 50,0 V
CAP. CER. SMD 56 PF 50,0 V
CAP. ELETROL. 220 µF 6,3 V
CAP. CER. SMD 56 PF 50,0 V
CAP. CER. SMD 100 nF 50,0 V
CAP. ELETROL. 100 µF 16,0 V
CAP. ELETROL. 100 µF 16,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. ELETROL. 10 µF 16,0 V
CAP. ELETROL. 10 µF 16,0 V
CAP. ELETROL. 47 µF 16,0 V
CAP. ELETROL. 1.000 µF 35,0 V
CAP. ELETROL. 1.000 µF 35,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. ELETROL. 470 µF 25,0 V
CAP. POLIÉSTER 220 nF 50,0 V
CAP. POLIÉSTER 220 nF 50,0 V
CAP. ELETROL. 47 µF 35,0 V
CAP. ELETROL. 3,30 µF 50,0 V

TC-14A12P / TC-20B12

TC-20B12

TC-20A12P

ECA1CM101B
ECJ2VC1H561K
ECJ2VC1H561K
ECJ2VB1H103J
ECJ2VB1H103J

ECA1CM101B
ECJ2VC1H561K
ECJ2VC1H561K

CAP. ELETROL. 100 µF 16,0 V
CAP. CER. SMD 560 PF 50,0 V
CAP. CER. SMD 560 PF 50,0 V
CAP. CER. SMD 10 nF 50,0 V
CAP. CER. SMD 10 nF 50,0 V

MTZJT-7716A
MTZJT-7716A
MTZJT-7730D
MTZJT-7730D
MA152KTX
MA152KTX
MA152KTX
ERA2204V3
ERA2204V3
ERA2204V3
MA152KTX
MTZJT-7710C
MA152KTX
D1NF60V70
MTZJT-7733B
MA4108JTA
MA171TA5
MA152KTX
MA3047HTX
D1NF60V70
MA152KTX
ERB06-15V1
RU2AMV1
MA185TA5
MA152KTX
MA152KTX
MA3056HTX
MA152WKTX
TAP2B0001
D4SB80
AG01ZV0
AG01ZV0
ERZV10V621CS
TLP721FD4GR-BR
MTZJT-7712B
AM01AV1
MA182TA5
AG01ZV0
ERA22-10G1
MA4068MTA
RU4AMLF-M1
S3L60P1520
AG01ZV0
RN1ZLF-A1
MTZJT-7710A
MTZJT-7724B
MA152KTX
MTZJT-775.6A
EL333ID/S928
TMW2B210
MTZJT-777.5C
MTZJT-775.6C
MTZJT-775.6C
MTZJT-775.6B
MA152KTX
MA152KTX
MA152KTX

DIODO ZENER 16,0 V 1/2 W 5,0 mA
DIODO ZENER 16,0 V 1/2 W 5,0 mA
DIODO ZENER 30,0 V 0,5 W 5,0 mA
DIODO ZENER 30,0 V 0,5 W 5,0 mA
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO SMD
DIODO ZENER 9,9 V 0,5 W 5,0 mA
DIODO CHAVEAMENTO SMD
DIODO RETIFICADOR
DIODO ZENER 33,0 V 1/2 W 5,0 mA
DIODO ZENER 10,8 V 0,37 W
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO SMD
DIODO ZENER SMD 4,7 V 1/10 W
DIODO RETIFICADOR
DIODO CHAVEAMENTO SMD
DIODO RETIFICADOR
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO SMD
DIODO ZENER SMD 5,8 V 1/10 W
DIODO CHAVEAMENTO SMD
POSISTOR 7 Ω
DIODO RETIFICADOR
DIODO RETIFICADOR
DIODO RETIFICADOR
VARISTOR
PHOTO ACOPLADOR
DIODO ZENER 12,0 V 1/2 W
DIODO RETIFICADOR
DIODO CHAVEAMENTO
DIODO RETIFICADOR
DIODO CHAVEAMENTO
DIODO ZENER 6,8 V 1/4 W
DIODO CHAVEAMENTO
DIODO CHAVEAMENTO
DIODO RETIFICADOR
DIODO CHAVEAMENTO
DIODO ZENER 9,6 V 1/2 W 5,0 mA
DIODO ZENER 24,0 V 1/2 W 5,0 mA
DIODO CHAVEAMENTO SMD
DIODO ZENER 5,4 V 1/2 W 5,0 mA
DIODO LED
SUPORTE DO LED
DIODO ZENER 7,5 V 1/2 W
DIODO ZENER 5,7 V 0,5 W
DIODO ZENER 5,7 V 0,5 W
DIODO ZENER 5,6 V 0,5 W 5,0 mA
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO SMD
DIODO CHAVEAMENTO SMD

XBA2C40TR0

FUSIVEL 4A 250V

Ref. No.

C2380
C3111
C3113
C3116
C3117

DIODES

D002
D003
D004
D005
D354
D355
D356
D360
D361
D362
D363
D365
D375
D402
D403
D511
D512
D520
D551
D552
D555
D556
D557
D558
D603
D606
D630
D660
D801
D802
D804
D805
D806
D807
D808
D811
D814
D816
D820
D824
D831
D837
D855
D856
D862
D865
D1101
D1102
D1104
D1104
D1105
D1130
D1131
D1204
D2320
D2380
D2381

MTZJT-7716A
MTZJT-7716A
MTZJT-7730D
MTZJT-7730D
MA152KTX
MA152KTX
MA152KTX
ERA2204V3
ERA2204V3
ERA2204V3
MA152KTX
MTZJT-7710C
MA152KTX
D1NF60V70
MTZJT-7733B
MA4108JTA
MA171TA5
MA152KTX
MA3047HTX
D1NF60V70
MA152KTX
ERB06-15V1
RU2AMV1
MA185TA5
MA152KTX
MA152KTX
MA3056HTX
MA152WKTX
TAP2B0001
D4SB80
AG01ZV0
AG01ZV0
ERZV10V621CS
TLP721FD4GR-BR
MTZJT-7712B
AM01AV1
MA182TA5
AG01ZV0
ERA22-10G1
MA4068MTA
RU4AMLF-M1
S3L60P1520
AG01ZV0
RN1ZLF-A1
MTZJT-7710A
MTZJT-7724B
MA152KTX
MTZJT-775.6A
EL333ID/S928
TMW2B210
MTZJT-777.5C
MTZJT-775.6C
MTZJT-775.6C
MTZJT-775.6B
MA152KTX
MA152KTX
MA152KTX

FUSE

F801

XBA2C40TR0

INTEGRATED CIRCUITS

IC351
IC451
IC601
IC801
IC802
IC851

TDA6107Q/N2
AN5539
TDA9381PS/N2/3H
STRW6654LF02
SE140N
AN7805LB

TDA6107Q/N2
AN5539
TDA9381PS/N2/3H
STRW6654LF02
SE140N
AN7805LB

Description

CIRCUITO INTEGRADO
CIRCUITO INTEGRADO
MICROCONTROLLER
CI REGULADOR DE TENSÃO
CI DETECTOR DE VOLTAGEM=10V
IC REGULADOR DE VOLTAGEM 4 V

TC-20B12

Ref. No.

IC852
IC1103
IC1104
IC1201
IC1202
IC2301

AN78M08LB
BR24C08F-E2
GP1U282Q
PQ1R33
AN7805LB
LA4289N

JUMPERS

JA2
JA3
JA4
JA5
JA7
JA8
JA9
JA10
JA11
JA12
JA14
JA15
JA16
JA17
JA18
JA20
JA25
JA27
JA30
JA31
JA32
JA33
JS002
JS2302
JS2310
JS3012
JS3130
JS3132
JS3136
JS3137
JS551
JS554
JS557
JS558
JS601
JS628
JS629
JS630
JS678
JS680
JS850
JS871

ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
----o-------o---ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V

COILS

L001
L181
L352
L501
L501
L550
L560
L619
L620
L621
L801
L820
L852
L856
L857
L1101

TALV35VB100K
TALV35VB6R8K
EXCELSA24T
ELH5L4115
ELH5LZ43Z
TSKA125
EXCELDR35V
TSK1045
TSK1045
EXCELSA39V
ELF21V012A
EXCELDR35C
TALL08N101KA
TALV35VB1R5K
TALV35VB1R5K
TALV35VB331K

TRANSISTORS

Q369
Q401
Q445
Q446
Q447

- 38 -

2SA1235A-T12
2SA1235A-T12
2SC3326ATX
2SC3052-T12
2SC3052-T12

TC-20A12P

Description

AN78M08LB
BR24C08F-E2
GP1U282Q
PQ1R33
AN7805LB
LA4289N

IC - REGULADOR DE VOLTAGEM
CI SMD MEMORIA EEPROM 8K
CI RECEPTOR COTROL REMOTO
CIRCUITO INTEGRADO SMD REG.3V
IC REGULADOR DE VOLTAGEM 4 V
CIRCUITO INTEGRADO SAÍDA DE AUDIO

ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
----o---ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V
ERJ3GEY0R00V

RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 0 Ω

TALV35VB100K
TALV35VB6R8K
EXCELSA24T
----o-------o---TSKA125
EXCELDR35V
TSK1045
TSK1045
EXCELSA39V
ELF21V012A
EXCELDR35C
TALL08N101KA
TALV35VB1R5K
TALV35VB1R5K
TALV35VB331K

BOBINA DE PICO 10 µH
BOBINA DE PICO 6,80 µH
FERRITE Z=20 Ω(100MHZ)
BOBINA LINEARIDADE
BOBINA DE LINEARIDADE 50,50 µH
BEAD CORE SMD
BOBINA DE PICO Z=80 Ω(100MHZ)
BEAD CORE SMD
BEAD CORE SMD
FERRITE Z=80 Ω(100MHZ)
FILTRO DE LINHA
BOBINA DE PICO Z= 80 Ω(100 MHZ)
BOBINA DE PICO 100 µH
BOBINA DE PICO 1,50 µH
BOBINA DE PICO 1,50 µH
BOBINA DE PICO 330 µH

2SA1235A-T12
2SA1235A-T12
2SC3326ATX
2SC3052-T12
2SC3052-T12

TRANSISTOR SMD
TRANSISTOR SMD
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W

TC-14A12P / TC-20B12
Ref. No.

Q501
Q520
Q551
Q601
Q602
Q603
Q605
Q606
Q852
Q857
Q1101
Q2320
Q2380
Q2381

TC-20B12

TC-20A12P

2SC4212HLB
2SB792ATX
2SD2539LB306
2SA1235A-T12
2SC3052-T12
2SA1235A-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SA1235A-T12
2SC3052-T12
2SA1235A-T12

2SC4212HLB
2SB792ATX
2SD2539LB306
2SA1235A-T12
2SC3052-T12
2SA1235A-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SC3052-T12
2SA1235A-T12
2SC3052-T12
2SA1235A-T12

TRANSISTOR DE POTÊNCIA NPN
TRANSISTOR SMD PNP 0,2 W
TRANSISTOR DE POTENCIA
TRANSISTOR SMD
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD
TRANSISTOR SMD NPN 0,1 W
TRANSISTOR SMD

ERJ3GEYJ100V
ERG3FJ822H
ERJ3GEYJ273V
ERJ3GEYJ472V
ERJ3GEYJ681V
ERJ3GEYJ221V
ERJ3EKF1001V
ERJ3EKF1001V
ERJ3EKF1001V
ERJ3EKF7870V
ERJ3EKF7870V
ERJ3EKF7870V
ERC12GK222V
ERC12GK222V
ERC12GK222V
ERJ3GEYJ103V
ERQ12AJ181P
----o---ERDS2TJ1R8T
ERJ3GEYJ103V
----o---ERJ3GEYJ332V
ERJ3EKF2701V
----o---ERJ3GEYJ272V
ERJ3GEYJ1R0V
----o---ERDS1TJ221T
ERJ3GEY0R00V
ERJ3GEYJ823V
----o---ERJ3GEYJ472V
----o---ERJ3GEYJ562V
----o---ERJ3GEYJ621V
ERDS1TJ1R0T
----o---ERDS2TJ562T
----o---ERDS1TJ132T
ERG1SJ182E
ERJ3GEYJ473V
ERJ3GEYJ473V
ERJ3GEYJ472V
ERJ3GEYJ242V
ERJ3GEYJ152V
ERJ3GEYJ182V
ERJ3GEY0R00V
ERG2SJ682E
ERJ3GEYJ101V
----o---ERG3FJ182H
ERG3FJ182H
----o-------o---ERJ6ENF1201V

RES. METALIC FILM SMD 10 Ω 1/10 W
RES. METALIC FILM 8,20 kΩ
RES. METALIC FILM SMD 27 kΩ 1/10 W
RES. METALIC FILM SMD 4,70 kΩ 1/10 W
RES. METALIC FILM SMD 680 Ω 1/10 W
RES. METALIC FILM SMD 220 Ω 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/16 W
RES. METALIC FILM SMD 1 kΩ 1/16 W
RES. METALIC FILM SMD 1 kΩ 1/16 W
RES. METALIC FILM SMD 787 Ω 1/16 W
RES. METALIC FILM SMD 787 Ω 1/16 W
RES. METALIC FILM SMD 787 Ω 1/16 W
RES. CARBONO 2,20 kΩ 1/2 W
RES. CARBONO 2,20 kΩ 1/2 W
RES. CARBONO 2,20 kΩ 1/2 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
FUSISTOR 180 Ω 1/2 W
RES. CARBONO 1,50 Ω 1/4 W
RES. CARBONO 1,80 Ω 1/4 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 1,80 kΩ 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 2,70 kΩ 1/16 W
RES. METALIC FILM SMD 2,20 kΩ 1/10 W
RES. METALIC FILM SMD 2,70 kΩ 1/10 W
RES. METALIC FILM SMD 1 Ω 1/10 W
RES. CARBONO 330 Ω 0,5 1/2 W
RES. CARBONO 220 Ω 1/2 W
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM SMD 82 kΩ 1/10 W
RES. METALIC FILM SMD 1,80 kΩ 1/10 W
RES. METALIC FILM SMD 4,70 kΩ 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. METALIC FILM SMD 430 Ω 1/10 W
RES. METALIC FILM SMD 620 Ω 1/10 W
RES. CARBONO 1 Ω 1/2 W
RES. CARBONO 1 Ω 1/2 W
RES. CARBONO 5,60 kΩ 1/4 W
RES. CARBONO 1,50 kΩ 1/2 W
RES. CARBONO 1,30 kΩ 1/2 W
RES. METALIC FILM 1,80 kΩ
RES. METALIC FILM SMD 47 kΩ 1/10 W
RES. METALIC FILM SMD 47 kΩ 1/10 W
RES. METALIC FILM SMD 4,70 kΩ 1/10 W
RES. METALIC FILM SMD 2,40 Ω 1/10 W
RES. METALIC FILM SMD 1,50 kΩ 1/10 W
RES. METALIC FILM SMD 1,80 kΩ 1/10 W
RES. METALIC FILM SMD 0 Ω
RES. METALIC FILM 6,80 kΩ
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM 1 kΩ 3 W
RES. METALIC FILM 1,80 kΩ 3 W
RES. METALIC FILM 1,80 kΩ 3 W
RES. METALIC FILM 1,20 kΩ 3 W
RES. METALIC FILM SMD 1,80 kΩ 1/10 W
RES. METALIC FILM SMD 1,20 kΩ 1/10 W

RESISTORS

R003
R004
R006
R007
R008
R182
R351
R352
R353
R354
R355
R356
R363
R364
R365
R369
R374
R401
R401
R402
R403
R403
R404
R405
R405
R406
R407
R407
R408
R409
R411
R411
R412
R412
R415
R415
R416
R417
R420
R443
R443
R444
R445
R446
R447
R448
R449
R502
R503
R504
R507
R508
R508
R509
R509
R511
R511

ERJ3GEYJ100V
ERG3FJ822H
ERJ3GEYJ273V
ERJ3GEYJ472V
ERJ3GEYJ681V
ERJ3GEYJ221V
ERJ3EKF1001V
ERJ3EKF1001V
ERJ3EKF1001V
ERJ3EKF7870V
ERJ3EKF7870V
ERJ3EKF7870V
ERC12GK222V
ERC12GK222V
ERC12GK222V
ERJ3GEYJ103V
ERQ12AJ181P
ERDS2TJ1R5T
----o---ERJ3GEYJ103V
ERJ3GEYJ182V
----o---ERJ3EKF2701V
ERJ3GEYJ222V
----o---ERJ3GEYJ1R0V
ERDS1TJ331T
----o---ERJ3GEY0R00V
ERJ3GEYJ823V
ERJ3GEYJ182V
----o---ERJ3GEYJ332V
----o---ERJ3GEYJ431V
----o---ERDS1TJ1R0T
ERDS1TJ1R0T
ERDS2TJ562T
ERDS1TJ152T
----o---ERG1SJ182E
ERJ3GEYJ473V
ERJ3GEYJ473V
ERJ3GEYJ472V
ERJ3GEYJ242V
ERJ3GEYJ152V
ERJ3GEYJ182V
ERJ3GEY0R00V
ERG2SJ682E
ERJ3GEYJ101V
ERG3FJ102H
----o-------o---ERG3FJ122H
ERJ6ENF1801V
----o----

Description

Ref. No.

R512
R512
R513
R520
R520
R521
R521
R522
R523
R524
R525
R553
R555
R557
R557
R558
R559
R559
R560
R601
R602
R603
R604
R605
R606
R607
R608
R609
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R620
R621
R622
R623
R624
R625
R626
R627
R628
R629
R630
R631
R632
R633
R634
R635
R636
R643
R655
R660
R661
R662
R801
R806
R807
R809
R811
R812
R814
R817
R819
R821
R824
R825

- 39 -

TC-20B12

TC-20A12P

ERJ6ENF1911V
----o---ERQ14AJ100P
ERX12SJ3R0E
----o---ERX12SJ3R0E
----o---ERJ3GEYJ123V
ERJ3GEYJ103V
ERJ3GEYJ104V
ERJ3GEYJ392V
ERJ3GEYJ223V
ERQ14AJ2R0E
ER050PKF1473
----o---ERDS2TJ223T
ERQ1CJP2R7S
----o---ERG1SJ102E
ERJ3GEYJ153V
ERJ3EKF3001V
ERJ3GEYJ393V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ103V
ERJ3GEYJ332V
ERJ3GEYJ332V
ERJ3GEYJ103V
ERJ3GEYJ472V
ERJ3GEYJ102V
ERJ3GEYJ391V
ERJ3GEYJ392V
ERJ3GEYJ102V
ERJ3GEYJ392V
ERJ6GEYJ181V
ERJ3GEYJ184V
ERJ3GEYJ121V
ERJ3GEYJ121V
ERJ3GEYJ103V
ERJ3GEYJ103V
ERJ3GEYJ331V
ERJ3GEYJ103V
ERJ3GEYJ222V
ERJ3GEYJ104V
ERJ3GEYJ683V
ERJ3GEYJ563V
ERJ3GEYJ154V
ERJ3EKF1802V
ER050PKF5603
ERJ3GEYJ750V
ERJ3GEYJ470V
ERJ3GEYJ822V
ERJ3GEYJ561V
ERJ3GEYJ562V
ERJ3GEYJ272V
ERJ3GEYJ103V
ERJ3GEYJ274V
ERJ3GEYJ103V
ERJ3GEYJ333V
ERF5ZK2R2
ERJ3GEYJ222V
ERJ6GEYJ152V
ERX12SJR39E
ERJ3GEYJ681V
ERD75TAJ825
ERJ3GEYJ332V
ERG3FJ183H
ERDS1TJ220T
ERG2SJS333H
ERDS1TJ624T
ERJ3GEYJ473V

----o---ERJ6ENF1101V
ERQ14AJ100P
----o---ERX12SJ3R3E
----o---ERX12SJ3R3E
ERJ3GEYJ123V
ERJ3GEYJ103V
ERJ3GEYJ104V
ERJ3GEYJ392V
ERJ3GEYJ223V
ERQ14AJ2R0E
----o---ER050PKF1743
ERDS2TJ223T
----o---ERQ1CJP2R2S
----o---ERJ3GEYJ153V
ERJ3EKF3001V
ERJ3GEYJ393V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ103V
ERJ3GEYJ332V
ERJ3GEYJ332V
ERJ3GEYJ103V
ERJ3GEYJ472V
ERJ3GEYJ102V
ERJ3GEYJ391V
ERJ3GEYJ392V
ERJ3GEYJ102V
ERJ3GEYJ392V
ERJ6GEYJ181V
ERJ3GEYJ184V
ERJ3GEYJ121V
ERJ3GEYJ121V
ERJ3GEYJ103V
ERJ3GEYJ103V
ERJ3GEYJ331V
ERJ3GEYJ103V
ERJ3GEYJ222V
ERJ3GEYJ104V
ERJ3GEYJ683V
ERJ3GEYJ563V
ERJ3GEYJ154V
ERJ3EKF1802V
ER050PKF5603
ERJ3GEYJ750V
ERJ3GEYJ470V
ERJ3GEYJ822V
ERJ3GEYJ561V
ERJ3GEYJ562V
ERJ3GEYJ272V
ERJ3GEYJ103V
ERJ3GEYJ274V
ERJ3GEYJ103V
ERJ3GEYJ333V
ERF5ZK2R2
ERJ3GEYJ222V
ERJ6GEYJ152V
ERX12SJR39E
ERJ3GEYJ681V
ERD75TAJ825
ERJ3GEYJ332V
ERG3FJ183H
ERDS1TJ220T
ERG2SJS333H
ERDS1TJ624T
ERJ3GEYJ473V

Description
RES. METALIC FILM SMD 1,91 kΩ 1/10 W
RES. METALIC FILM SMD 1,10 kΩ 1/10 W
FUSISTOR 10 Ω 1/4 W
RES. METALIC FILM 3 Ω 1/2 W
RES. METALIC FILM 3,30 Ω 1/2 W
RES. METALIC FILM 3 Ω 1/2 W
RES. METALIC FILM 3,30 Ω 1/2 W
RES. METALIC FILM SMD 12 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 100 kΩ 1/10 W
RES. METALIC FILM SMD 3,90 kΩ 1/10 W
RES. METALIC FILM SMD 22 kΩ 1/10 W
FUSISTOR 2 Ω 1/4 W
RES. METALIC FILM 147 kΩ 1/2 W
RES. METALIC FILM AXIAL 174 kΩ 1/2 W
RES. CARBONO 22 kΩ 1/4 W
FUSISTOR 2,70 Ω 1 W
FUSISTOR 2,20 Ω 1 W
RES. METALIC FILM 1 kΩ 1 W
RES. METALIC FILM SMD 15 kΩ 1/10 W
RES. METALIC FILM SMD 3 kΩ 1/16 W
RES. METALIC FILM SMD 39 kΩ 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 4,70 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 390 Ω 1/10 W
RES. METALIC FILM SMD 3,90 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 3,90 kΩ 1/10 W
RES. METALIC FILM SMD 180 Ω 1/8 W
RES. METALIC FILM SMD 180 kΩ 1/10 W
RES. METALIC FILM SMD 120 Ω 1/10 W
RES. METALIC FILM SMD 120 Ω 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 330 Ω 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 2,20 kΩ 1/10 W
RES. METALIC FILM SMD 100 kΩ 1/10 W
RES. METALIC FILM SMD 68 kΩ 1/10 W
RES. METALIC FILM SMD 56 kΩ 1/10 W
RES. METALIC FILM SMD 150 kΩ 1/10 W
RES. METALIC FILM SMD 18 kΩ 1/16 W
RES. METALIC FILM 560 kΩ 1/2 W
RES. METALIC FILM SMD 75 Ω 1/10 W
RES. METALIC FILM SMD 47 Ω 1/10 W
RES. METALIC FILM SMD 8,20 kΩ 1/10 W
RES. METALIC FILM SMD 560 Ω 1/10 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. METALIC FILM SMD 2,70 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 270 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 33 kΩ 1/10 W
RESISTOR DE FIO CIMENTADO 2,20 Ω 5 W
RES. METALIC FILM SMD 2,20 kΩ 1/10 W
RES. METALIC FILM SMD 1,50 kΩ 1/8 W
RES. METALIC FILM 0,39 Ω 1/2 W
RES. METALIC FILM SMD 680 Ω 1/10 W
RES. CARBONO 8,20 MΩ 3/4 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM 18 kΩ 3 W
RES. CARBONO 22 Ω 1/2 W
RES. METALIC FILM 33 kΩ 2W
RES. CARBONO 620 kΩ 1/2 W
RES. METALIC FILM SMD 47 kΩ 1/10 W

TC-14A12P / TC-20B12

TC-20B12

Ref. No.

R832
R835
R850
R856
R857
R864
R866
R868
R870
R871
R1016
R1017
R1018
R1019
R1020
R1021
R1022
R1101
R1104
R1105
R1106
R1108
R1109
R1117
R1120
R1122
R1124
R1125
R1130
R1131
R1132
R1140
R1141
R2022
R2301
R2304
R2305
R2310
R2318
R2319
R2320
R2321
R2322
R2380
R2381
R2382
R2383
R2419
R3132
R3133

ERDS1TJ152T
ERX12SJR39E
ERQ12HKR68P
ERQ12HJ1R5P
ERQ12HKR82P
ERJ3GEYJ103V
ERJ3GEYJ472V
ERJ3GEYJ242V
ER0S2THF2201
ERDS1TJ223T
ERJ3EKF1651V
ERJ3EKF2151V
ERJ3EKF3091V
ERJ3EKF4421V
ERJ3EKF7501V
ERJ3EKF1871V
ERJ3GEYJ100V
ERJ3GEYJ332V
ERJ3GEYJ562V
ERJ3GEYJ562V
ERJ3GEYJ102V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ471V
ERJ3GEYJ432V
ERJ3GEYJ332V
ERJ3GEY0R00V
ERDS2TJ560T
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3EKF1002V
ERJ3GEYJ562V
ERJ3GEYJ104V
ERJ3GEYJ562V
ERDS2TJ222T
ERQ2CJP8R2S
ERDS2TJ1R0T
ERJ3GEYJ332V
ERJ3GEYJ102V
ERJ3GEYJ102V
ERJ3GEYJ682V
ERJ3GEYJ153V
ERJ3GEYJ151V
ERJ3GEYJ102V
ERJ3GEYJ102V
ERJ3GEYJ103V
ERDS2TJ680T
ERJ3GEYJ221V
ERJ3GEYJ221V

SWITCHES

S1001
S1002
S1003
S1004
S1005
S1006
S801

EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
ESB92DA1B

TC-20A12P

RES. CARBONO 1,50 kΩ 1/2 W
RES. METALIC FILM 0,39 Ω 1/2 W
FUSISTOR 0,68 Ω 1/2 W
FUSISTOR 1,50 Ω 1/2 W
FUSISTOR 0,82 Ω 1/2 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. METALIC FILM SMD 4,70 kΩ 1/10 W
RES. METALIC FILM SMD 2,40 Ω 1/10 W
RES. CARBONO 2,20 kΩ 1/4 W
RES. CARBONO 22 kΩ 1/2 W
RES. METALIC FILM SMD 1,65 kΩ 1/16 W
RES. METALIC FILM SMD 2,15 kΩ 1/16 W
RES. METALIC FILM SMD 3,09 kΩ 1/16 W
RES. METALIC FILM SMD 4,42 kΩ 1/16 W
RES. METALIC FILM SMD 7,50 kΩ 1/16 W
RES. METALIC FILM SMD 1,87 kΩ 1/16 W
RES. METALIC FILM SMD 10 Ω 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 470 Ω 1/10 W
RES. METALIC FILM SMD 4,30 kΩ 1/10 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 0 Ω
RES. CARBONO 56 Ω 1/4 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 100 Ω 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/16 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. METALIC FILM SMD 100 kΩ 1/10 W
RES. METALIC FILM SMD 5,60 kΩ 1/10 W
RES. CARBONO 2,20 kΩ 1/4 W
FUSISTOR 8,20 Ω 2 W
RES. CARBONO 1 Ω 1/4 W
RES. METALIC FILM SMD 3,30 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 6,80 kΩ 1/10 W
RES. METALIC FILM SMD 15 kΩ 1/10 W
RES. METALIC FILM SMD 150 Ω 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 1 kΩ 1/10 W
RES. METALIC FILM SMD 10 kΩ 1/10 W
RES. CARBONO 68 Ω 1/4 W
RES. METALIC FILM SMD 220 Ω 1/10 W
RES. METALIC FILM SMD 220 Ω 1/10 W

EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
EVQ11G05R
ESB92DA1B

CHAVE DE TOQUE
CHAVE DE TOQUE
CHAVE DE TOQUE
CHAVE DE TOQUE
CHAVE DE TOQUE
CHAVE DE TOQUE
CHAVE INTERRUPTORA

KFT2AA427F
ETH19Y70AY
TLP4GA020D

FLY BACK
FLY BACK
TRANSFORMADOR DRIVER
TRANSFORMADOR CHOPER

TEDH9-301A

SELETOR DE CANAIS

M1971M
EFCT4R5MW5
TSSA010

FILTRO SAW 45,75 MHZ
FILTRO TRAP CER. 4,50 MHZ
CRISTAL PIEZOELETRICO 12.000 MHZ

KFT3AA428F

ETH19Y70AY
TLP4GA020D

TUNER

TNR001 TEDH9-301A

CRISTALS

X101
X180
X601

M1971M
EFCT4R5MW5
TSSA010

Ref. No.

ERDS1TJ152T
ERX12SJR39E
ERQ12HKR68P
ERQ12HJ1R5P
ERQ12HKR82P
ERJ3GEYJ103V
ERJ3GEYJ472V
ERJ3GEYJ242V
ER0S2THF2201
ERDS1TJ223T
ERJ3EKF1651V
ERJ3EKF2151V
ERJ3EKF3091V
ERJ3EKF4421V
ERJ3EKF7501V
ERJ3EKF1871V
ERJ3GEYJ100V
ERJ3GEYJ332V
ERJ3GEYJ562V
ERJ3GEYJ562V
ERJ3GEYJ102V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ471V
ERJ3GEYJ432V
ERJ3GEYJ332V
ERJ3GEY0R00V
ERDS2TJ560T
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3GEYJ101V
ERJ3EKF1002V
ERJ3GEYJ562V
ERJ3GEYJ104V
ERJ3GEYJ562V
ERDS2TJ222T
ERQ2CJP8R2S
ERDS2TJ1R0T
ERJ3GEYJ332V
ERJ3GEYJ102V
ERJ3GEYJ102V
ERJ3GEYJ682V
ERJ3GEYJ153V
ERJ3GEYJ151V
ERJ3GEYJ102V
ERJ3GEYJ102V
ERJ3GEYJ103V
ERDS2TJ680T

TRANSFORMERS

T552
T552
T553
T801

Description

TC-20B12

A1OTHERS
BJP11V04-AP
A22
BJP11V02-AP
A5-L5 TXAJTA5CB14A12
A8-L8 TXAJTA8CB20A12
F801-L TP00351-51
F801-R TP00351-51
JK3001 TJB16664
JK3101 TJB4G605
JK351 330550044K2F
JK351 - - - - o - - - -

- 40 -

TC-20A12P
BJP11V04-AP
BJP11V02-AP
TXAJTA5CB14A12
TXAJTA8CB14A12
TP00351-51
TP00351-51
TJB16664
----o-------o---330620065

Description
BASE DE PINOS 4P
PORTA TERMINAL MACHO
CONECTOR 3 VIAS
CONECTOR 6 VIAS
SUPORTE DE FUSÍVEL
SUPORTE DE FUSÍVEL
AV TERMINAL
AV TERMINAL
SOCKET (CRT 20")
SOCKET (CRT 14")

Panasonic do Brasil Ltda.
CS GROUP - TECHNICAL SUPPORT



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 1910:20:82 01:21:70
Producer                        : Acrobat Distiller 3.01 for Windows
Author                          : 
Creator                         : PageMaker 6.5
Title                           : 
Modify Date                     : 2002:08:20 17:08:32-02:00
Page Count                      : 42
Page Mode                       : UseThumbs
EXIF Metadata provided by EXIF.tools

Navigation menu