QCA6410 HomePlug?AV MAC/PHY Transceiver Data Sheet PLC Chipset SG Programmers Guide
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 31
| Download | |
| Open PDF In Browser | View PDF |
第1页 al QCA-PLC-SG-firmware-v1.0.0 - Draft nti PLC Chipset SG Programmers Guide Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e MKG-xxxxx Ver. Draft May, 2013 Confidential and Proprietary - Qualcomm Atheros, Inc. Not to be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of Qualcomm Atheros, Inc. QUALCOMM is registered trademark of Qualcomm Incorporated. ATHEROS is a registered trademark of Qualcomm Atheros, Inc. All other registered and unregistered trademarks are the property of Qualcomm Incorporated, Qualcomm Atheros, Inc. or their respective owners and used with permission. Registered marks owned by Qualcomm Incorporated and Qualcomm Atheros, Inc. are registered in the United States of America and may be registered in other countries. Qu This technical data may be subject to U.S. and international export, re-export, or transfer (“export”) laws. Diversion contrary to U.S. and international law is strictly prohibited. Qualcomm Atheros, Inc. 1700 Technology Drive San Jose, CA 95110-1383 U.S.A. Copyright © 2011 QUALCOMM Incorporated. All rights reserved. 第2页 QCA-PLC-SG-firmware-v1.0.0 Revision History Revision April, 2013 Description Initial version Qu Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti al Ver. 1.0 Date 第3页 QCA-PLC-SG-firmware-v1.0.0 Contents 1 Acronyms and Abbreviations .................................................................................................................... 5 2 Architecture Overview .............................................................................................................................. 6 SG System architecture ..................................................................................................................... 6 nti al 2.2 fid e UART Data transparent TX/RX................................................................................................................... 7 3.1 UART Data transmit........................................................................................................................... 7 3.2 UART Data receive............................................................................................................................. 8 3.3 Power Meter Address and MAC address Mapping ........................................................................... 8 Communication protocol .......................................................................................................................... 9 4.1 Protocol ............................................................................................................................................. 9 4.2 Ethernet MME packet header ........................................................................................................... 9 4.3 Get power meter data request (VS_UART_CMD_Req MME) ........................................................... 9 4.4 Get power meter data response (VS_UART_CMD_Cnf) ................................................................. 10 4.5 Get topology request and response (VS_AVLN_TOPO_Req VS_AVLN_TOPO_Cnf) ....................... 11 4.6 Network information request (VS_NW_INFO_STATS_Req)............................................................ 14 4.7 Network information response (VS_NW_INFO_STATS_Cnf) .......................................................... 15 4.8 Get software version request (VS_SW_VER_Req) .......................................................................... 16 4.9 Get software version response (VS_SW_VER_Cnf)......................................................................... 17 4.10 Software reset request (VS_RS_DEV_Req) ..................................................................................... 17 Qu 4 Power line Frequency........................................................................................................................ 6 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n 3 2.1 4.11 Software reset response (VS_RS_DEV_Cnf) .................................................................................... 17 4.12 MME timeout .................................................................................................................................. 18 Appendix : Example for Concentrator raw socket programming ................................................................... 19 第4页 QCA-PLC-SG-firmware-v1.0.0 Table and Figure Figure 2-1：QCA broadband PLC Smart Grid system block diagram ....................................................... 6 al Figure 3-1：UART data transparently transmit ........................................................................................ 7 nti Figure 3-2：UART data transparently receive .......................................................................................... 8 fid e Figure 4-1：MME packet captured by wireshark ................................................................................... 10 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n Figure 5-2：Raw UART Data sent ........................................................................................................... 10 Table 2-1：Acronyms and Abbreviations ................................................................................................. 5 Table 4-1：MME Packet Header .............................................................................................................. 9 Table 4-2：VS_UART_CMD_Req .............................................................................................................. 9 Table 4-3：VS_UART_CMD_Cnf ............................................................................................................. 10 Table 4-4：VS_AVLN_TOPO_Req ........................................................................................................... 11 Table 4-5：VS_AVLN_TOPO_Cnf ............................................................................................................ 11 Table 4-6：VAR field for Get tree command .......................................................................................... 12 Table 4-7：VAR field for Get trace command ........................................................................................ 12 Qu Table 4-8：STA’s Info .............................................................................................................................. 13 Table 4-9： VS_NW_INFO_STATS_Req .................................................................................................. 14 Table 4-10： VS_NW_INFO_STATS_Cnf ................................................................................................. 16 Table 4-11： VS_SW_VER_Req ............................................................................................................... 16 Table 4-12： VS_SW_VER_Cnf................................................................................................................ 17 Table 4-13： VS_RS_DEV_Req ................................................................................................................ 17 Table 4-14： VS_RS_DEV_Cnf................................................................................................................. 17 QCA-PLC-SG-firmware-application-notes v1.0.0 page 5 1 Acronyms and Abbreviations Acronyms Definition One phase Smart meter and three phase Smart meter CCO module CCO module is placed into concentrator. It included 3 QCA6411, 1 5-ports-switch. STA module STA module is placed into smart meter. It included 1 QCA7000. STA Station Normal STA PSTA Proxy STA HSTA Hidden STA Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n NSTA nti Central Coordinator fid e CCO al Power Meter AVLN HomePlug AV Logical Network Relay CCO cannot communicate with 1 HSTA, but via PSTA with relay, it can communicate with each other. n Relay MME Multi- relay MAC Management Message PB PHY Block TEI Terminal Equipment Identifier QCA6411 Lynx chip used for CCO QCA7000 Lynx chip used for STA DA Destination Address，Destination MAC address SA Source Address，Source MAC address。 Qu Table 1-1：Acronyms and Abbreviations QCA-PLC-SG-firmware-application-notes v1.0.0 page 6 2 Architecture Overview 2.1 Power line Frequency al To comply with the HomePlug GP specification, the Powerline frequency must be 50Hz±3.0% or 60 Hz±3.5%. Powerline frequency outside of this range will cause the firmware to reboot the device. Qu Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti 2.2 SG System architecture Figure 2-1：QCA broadband PLC Smart Grid system block diagram CCO module was plugged into concentrator, which had 3 QCA6411 corresponding to 3 phase power line, per QCA6411 use different Network password to indicate 3 different AVLAN. Per VLAN support 253 STAs. STA module was plugged into power meter, which deployed with 1 QCA7000.STA module fetch power meter data via UART @2400 baud rate. UART baud rate can be configured with AVITAR tools. 3 QCA6411 connect with switch and communicate with concentrator via Ethernet port. QCA-PLC-SG-firmware-application-notes v1.0.0 page 7 3 UART Data transparent TX/RX 3.1 UART Data transmit nti al Payload was raw UART data user wants to send to power meter. Maxim UART data length is within 256 Bytes. fid e This transmit is initiated by Concentrator, so user need to fill in MME packet, refer chapter 4 for sending MME Data. Qu Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n UART data will transparently send to power meter, so the UART data should be valid and can be recognized by power meter. Here Payload is UART RAW data. Figure 3-1：UART data transparently transmit QCA-PLC-SG-firmware-application-notes v1.0.0 page 8 3.2 UART Data receive Qu Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti al Payload was raw UART data which power meter response. Maxim UART data length is within 256 Bytes. UART data will be sent to concentrator transparently. Received MME packet, concentrator can recognize which STA Module response. Further UART data analysis will be handled by concentrator. Figure 3-2：UART data transparently receive 3.3 Power Meter Address and MAC address Mapping Per STA module has own mac address (QCA7000 MAC Address), which was stored in NVM. This mac address can be configured by AVITAR tools. The mapping relationship between QCA7000 module MAC address and Meter ID should be maintained by Concentrator program. Power meter address and mac address mapping can be realized by following steps: 1. Concentrator sends VS_NW_INFO_STATS_Req MME to fetch how many STA modules are online. 2. Concentrator initially sends unicast MME frame to online STA module. Payload (UART Data) should be data to fetch the power meter address or other packet which power meter can recognize. 3. Concentrator analysis the received payload, and extract the power meter ID. 4. Maintain the mapping with STA module MAC address with power meter ID. QCA-PLC-SG-firmware-application-notes v1.0.0 page 9 4 Communication protocol 4.1 Protocol Concentrator communicates with CCO Module via MME. CCO communicate with remote server via private protocol, such as 372.1 etc. CCO Module communicates with STA Module via HomePlugAV protocol. nti al Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n 4.2 Ethernet MME packet header fid e The user just focus on protocol (MME) between Concentrator with CCO module, low level communication is invisible to user. Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 Size 6 6 2 1 2 3 Field Name ODA OSA MTYPE MMV MMTYPE OUI Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) MME Type Intellon OUI (0x00, 0xb0, 0x52) Table 4-1：MME Packet Header Different Ethernet MME is raw mac frame which shared same packet heard, refer table 4-1. 4.3 Get power meter data request (VS_UART_CMD_Req MME) Qu Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 0x0016 Size 6 6 2 1 2 3 2 Variable Field Name ODA OSA MTYPE MMV MMTYPE OUI LENGTH DATA Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA400 (Request) Intellon OUI (0x00, 0xb0, 0x52) UART raw data length UART raw data Table 4-2：VS_UART_CMD_Req ODA: OSA: MTYPE: MMV: MMTYPE: OUI: LENGTH: DATA: STA module mac address Concentrator mac address 0x88, 0xE1 (constant ) 0 (constant ) 0xA400(constant ) 0x00, 0xB0, 0x52(constant ) Length of DATA, size in bytes UART command(raw data) QCA-PLC-SG-firmware-application-notes v1.0.0 page 10 al Use wire shark tools to monitor the data you send, the captured data should be like Figure 5-1. fid e nti Figure 4-1：MME packet captured by wireshark Figure 4-2：Raw UART Data sent Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n 4.4 Get power meter data response (VS_UART_CMD_Cnf) Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 0x001A 0x001C Size 6 6 2 1 2 3 6 2 Variable Field Name ODA OSA MTYPE MMV MMTYPE OUI RSVD LENGTH DATA Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA401 (Confirm) Intellon OUI (0x00, 0xb0, 0x52) Reserved UART raw data length UART raw data Table 4-3：VS_UART_CMD_Cnf ODA: OSA: MTYPE: MMTYPE: MMV: OUI: LENGTH: DATA: Qu Concentrator mac address STA module mac address 0x88, 0xE1 (constant ) 0xA401(constant ) 0 (constant ) 0x00, 0xB0, 0x52(constant ) Length of DATA, size in bytes UART response(raw data) This mac frame is generated by STA module, so concentrator need to further analysis the data. QCA-PLC-SG-firmware-application-notes v1.0.0 page 11 4.5 Get topology request and response (VS_AVLN_TOPO_Req VS_AVLN_TOPO_Cnf) Offset Size Field Name Description 6 ODA Original Destination Address 0x0006 6 OSA Original Source Address 0x000C 2 MTYPE Ethertype (0x88, 0xE1) 0x000E 1 MMV MME Version (0) 0x000F 2 MMTYPE 0x0011 3 OUI fid e nti al 0x0000 0xA308 (Request) Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n Intellon OUI (0x00, 0xb0, 0x52) 0x0012 1 COMMAND 0x01: get tree 0x02: trace 0x03-0xff: reserved 0x0013 n VAR Base on command type Table 4-4：VS_AVLN_TOPO_Req Offset Size Field Name Description 0x0000 6 ODA Original Destination Address 0x0006 6 OSA Original Source Address 0x000C 2 MTYPE Ethertype (0x88, 0xE1) 0x000E 1 MMV MME Version (0) 0x000F 2 MMTYPE 0xA309 (Confirm) 0x0011 3 OUI Intellon OUI (0x00, 0xb0, 0x52) 0x0014 1 COMMAND 0x01: get tree Qu 0x02: trace 0x0015 0x03-0xff: reserved 1 RESPONSE LSB 0th bit: show whether the response is successful or not. “1” is fail, “0” is successful. MSB 7th bit: show whether current MME has more MME followed. “1” is yes, “0” means “no” and current is the last MME. Other bits: reserved 0x0016 n VAR Base on command type Table 4-5：VS_AVLN_TOPO_Cnf This MME is sent by concentrator, it shows all the directly connected STA information under the given STA. Further, it can be used to show the whole topology of one AVLN. page 12 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti al QCA-PLC-SG-firmware-application-notes v1.0.0 Table 4-6：VAR field for Get tree command only for Cnf MME. If the response is successful or not. “1” is fail, “0” is successful Root MAC: the MAC of chosen STA to query NumOfSTA: the number of STA directly under the chosen STA STAn Info: the Nth STA’s Info. Check table 4-8. Qu Response: Table 4-7：VAR field for Get trace command QCA-PLC-SG-firmware-application-notes v1.0.0 page 13 Root MAC: NumOfSTA: the number of STA in the path from chosen STA to CCO STAn Info: the chosen STA’s MAC Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti al the Nth STA’s Info. Check table 4-8. Table 4-8：STA’s Info MAC: STA MAC TEI: STA TEI NumOfSTA: the number of STA directly under this STA Status: the status of this STA. currently “1” means authenticated, “0” is associated For Trace subcommand, numOfSTA and Status can be ignored Following could be used as guide to develop application feature at concentrator to get topology related information. In order to get the topology of CCo, App should follow below steps: Qu 1. Send a get tree command to CCo, “root MAC” is CCo’s MAC 2. CCo will return the list of STAs directly connected to it. 3. App check each STA’s info, if any STA has at least one STA under it (numOfSTA is non-zero in Error! Reference source not found.), App should send a similar get tree command to CCo with root MAC” set to STA’s mac instead. (NOTE: STAs having other STA under it are the non-leaf node in the tree topology, STAs not having other STA under it are the leaf node in the tree topology) 4. Loop 3 until complete sending request MME to CCo for querying all the non-leaf STA (loop all the non-leaf STAs by sending a get tree command) 5. App construct the tree topology based on the information above and show it out. To get the data path (relay path) for a STA, App should follow below steps: 1. Send a trace command to CCo, “root MAC” is the STA’s MAC 2. CCo will return a response with the STA list where all STAs on the path between STA and CCo are listed. 3. App show it out. QCA-PLC-SG-firmware-application-notes v1.0.0 page 14 4.6 Network information request (VS_NW_INFO_STATS_Req) Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA074 (Request) Intellon OUI (0x00, 0xb0, 0x52) First TEI requested. If FIRST_TEI is Zero the NUMSTAS field will be valid and up to 96 sets of Station Information will be returned. Otherwise the NUMSTAS field will list the number of sets of Station Information returned and all the existent sets of Station Information will be return at or after the FIRST_TEI (up to 96). nti al Field Name ODA OSA MTYPE MMV MMTYPE OUI FIRST_TEI fid e Size 6 6 2 1 2 3 1 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 Table 4-9： VS_NW_INFO_STATS_Req This MME is sent by concentrator to get the network information, which devices registered in the network, and get the MAC address of each device, if some expected devices not exist in the network, concentrator cannot communicate with these devices. Notes: If FIRST_TEI is set to 0, NUMSTAS in the response stands for total stations in the network, if the number is bigger than 96, users should send the second or maybe third request to get the information(max station number in a network is 253), since the max size of Ethernet frame is 1514 octets. FIRST_TEI = 0, The second request, FIRST_TEI = 98, FIRST_TEI = 194, Qu The first request, The third request, Station TEI starts from 2, the MAX TEI is 254. QCA-PLC-SG-firmware-application-notes v1.0.0 page 15 4.7 Network information response (VS_NW_INFO_STATS_Cnf) al ODA OSA MTYPE MMV MMTYPE OUI FIRST_TEI IN_AVLN NID Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA075 (Confirm) Intellon OUI (0x00, 0xb0, 0x52) First TEI from Request. Station is a Member of an AVLN Network Identifier The least significant 54 bits of this field contains the NID of the AVLN. The remaining 2 bits are set to 0b00. Short Network Identifier The last significant 4 bits of this field contains the Short Network Identifier. The remaining 4 bits are set to 0x0 Terminal Equipment Identifier of the STA in the AVLN Role of the station in the AVLN 0x00 = STA 0x01 = Proxy Coordinator 0x02 = CCo 0x03 – 0xFF = reserved MAC Address of the CCo of the network. Access Network 0x00 = This NID corresponds to an in-home network 0x01 = This NID corresponds to an Access Network 0x02 - 0xFF = reserved Number of Neighbor Networks that are nti 6 6 2 1 2 3 1 1 7 Field Name fid e Size Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 0x0015 0x0016 1 SNID 0x001E 1 TEI 0x001F 1 STATIONROLE 0x0020 0x0026 6 1 CCO_MACADDR ACCESS 1 NumCordNWs Qu 0x001D 0x0027 coordinating with the AVLN 0x0028 1 CCO_TEI 0x0029 1 NUMSTAS 0x002A 6 DA[0] 0x00 = none (Un-Coordinated mode) 0x01 = one Coordinating network, and so on Terminal Equipment Identifier of the CCo in the AVLN Number of AV STAs in the AVLN = L 0x00 = None, 0x01 = One, and so on. MAC Address of the STA – 0 0x0030 1 TEI[0] TEI of the STA – 0 0x0031 6 1stBDA[0] MAC Address of the first Node bridged by STA – 0 QCA-PLC-SG-firmware-application-notes v1.0.0 0x0037 1 0x0038 1 AvgPHYDR_TX[0] page 16 Average PHY Data Rate in Mega Bits per second from STA to DA[0]. 0x00 = unreachable/unknown 0x01 = 1 Mbps, and so on Average PHY Data Rate in Mega Bits per second from DA[0] to STA. 0x00 = unreachable/unknown 0x01 = 1 Mbps, and so on *** MAC Address of STA – (L-1) TEI of the STA – (L-1) 6 1stBDA[L-1] fid e DA[L-1] TEI[L-1] MAC Address of the first Node bridged by STA – (L-1) Average PHY Data Rate in Mega Bits per second from STA to DA[0]. 0x00 = unreachable/unknown 0x01 = 1 Mbps, and so on Average PHY Data Rate in Mega Bits per second from DA[0] to STA. 0x00 = unreachable/unknown 0x01 = 1 Mbps, and so on Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n 6 1 nti al AvgPHYDR_RX[0] 1 AvgPHYDR_TX[L-1] 1 AvgPHYDR_RX[L-1] Table 4-10： VS_NW_INFO_STATS_Cnf 4.8 Get software version request (VS_SW_VER_Req) Qu Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 Size 6 6 2 1 2 3 Field Name ODA OSA MTYPE MMV MMTYPE OUI Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (=0) 0xA000 (Request) Intellon OUI (0x00, 0xb0, 0x52) Table 4-11： VS_SW_VER_Req This MME is sent by concentrator to get software version of devices, the destination could be QCA6411 or QCA7000. QCA-PLC-SG-firmware-application-notes v1.0.0 page 17 4.9 Get software version response (VS_SW_VER_Cnf) al Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA001 (Confirm) Intellon OUI (0x00, 0xb0, 0x52) MME Status (0x00=Success) Device ID Length of Version String (including null) Version String nti Field Name ODA OSA MTYPE MMV MMTYPE OUI MSTATUS MDEVICEID MVERLENGTH MVERSION RSVD fid e Size 6 6 2 1 2 3 1 1 1 128 5 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 0x0015 0x0016 0x0017 0x0097 Table 4-12： VS_SW_VER_Cnf 4.10 Software reset request (VS_RS_DEV_Req) Size 6 6 2 1 2 3 Field Name ODA OSA MTYPE MMV MMTYPE OUI Qu Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA01C (Request) Intellon OUI (0x00, 0xb0, 0x52) Table 4-13： VS_RS_DEV_Req This MME is sent by concentrator to reset target device. 4.11 Software reset response (VS_RS_DEV_Cnf) Offset 0x0000 0x0006 0x000C 0x000E 0x000F 0x0011 0x0014 Size 6 6 2 1 2 3 1 Field Name ODA OSA MTYPE MMV MMTYPE OUI MSTATUS Description Original Destination Address Original Source Address Ethertype (0x88, 0xE1) MME Version (0) 0xA01D (Confirm) Intellon OUI (0x00, 0xb0, 0x52) MME Status (0x00=Success, 0x01 = Failure) Table 4-14： VS_RS_DEV_Cnf QCA-PLC-SG-firmware-application-notes v1.0.0 page 18 4.12 MME timeout Qu Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e nti al The ODA of MME should be existed in the network information. If not, there will be no response. The time out is defined by user; it can be 3 or 5 seconds. QCA-PLC-SG-firmware-application-notes v1.0.0 page 19 Appendix : Example for Concentrator raw socket programming Filename: plc.h al #ifndef __PLC_H__ #define __PLC_H__ #includefid e ( sizeof(struct cmd_req_hdr) ) ( sizeof(struct cmd_ind_hdr) ) Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n #define CMD_REQ_HDR_SZ #define CMD_IND_HDR_SZ nti typedef unsigned short uint16; typedef unsigned char byte; typedef unsigned char uint8; /* Default settings of cmd_req_hdr */ #define REQ_MTYPE #define REQ_MMV #define REQ_MMTYPE #define REQ_OUI0 #define REQ_OUI1 #define REQ_OUI2 0x88e1 0x00 0xA400 0x00 0xB0 0x52 /*mme type*/ #define MMTYPE_CMD_IND 0xa402 /*Ether packet type*/ #define ETH_P_HPAV 0x88e1 Qu /*struct type */ struct cmd_req_hdr { struct ethhdr eth_hdr; uint8 mmv; uint16 mmtype; char oui[3]; uint16 length; byte data[0]; } __attribute__((packed)); struct cmd_cnf_hdr { struct ethhdr eth_hdr; uint8 mmv; uint16 mmtype; char oui[3]; uint16 length; byte data[0]; } __attribute__((packed)); nti fid e struct cmd_ind_hdr { struct ethhdr eth_hdr; uint8 mmv; uint16 mmtype; char oui[3]; byte address[ETH_ALEN]; uint16 length; byte data[0]; } __attribute__((packed)); page 20 al QCA-PLC-SG-firmware-application-notes v1.0.0 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n extern void cmd_req_hdr_init( struct cmd_req_hdr* p_req_hdr, const uint8* const dest_mac, const uint8* const src_mac, uint16 len); #endif Filename: plc.c #include #include "plc.h" Qu void cmd_req_hdr_init( struct cmd_req_hdr* p_req_hdr, const uint8* const dest_mac, const uint8* const src_mac, uint16 len) { memcpy( p_req_hdr->eth_hdr.h_dest, dest_mac, ETH_ALEN ); memcpy( p_req_hdr->eth_hdr.h_source, src_mac, ETH_ALEN ); p_req_hdr->eth_hdr.h_proto = htons( REQ_MTYPE ); p_req_hdr->mmv = REQ_MMV; p_req_hdr->mmtype = REQ_MMTYPE; p_req_hdr->oui[0] = REQ_OUI0; p_req_hdr->oui[1] = REQ_OUI1; p_req_hdr->oui[2] = REQ_OUI2; /*p_req_hdr->length = htons( len );*/ p_req_hdr->length = len; } Filename: common.h extern int str2hex( const char* str, char byte[], int *psize ); extern int find_char( char str[], int len, char ch ); Filename: common.c #include int str2hex( const char* str, char byte[], int *psize ) { char ch; int i = 0; if( str == NULL ) return -1; while ( (ch = *str++) != '\0' ) { if (ch >= 'a' && ch <= 'f') ch = ch - 'a' + 0x0a; QCA-PLC-SG-firmware-application-notes v1.0.0 else if (ch >= 'A' && ch <= 'F') else if (ch >= '0' && ch <= '9') else continue; page 21 ch = ch - 'A' + 0x0a; ch = ch - '0'; if ( i % 2 == 0 ) byte[ i++ / 2 ] = ch << 4; else byte[ i++ / 2 ] += ch; al } Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n /* Count char */ int find_char( char str[], int len, char ch ) { int i = 0; for (i = 0; i < len; i++) if ( str[i] == ch ) return i; return -1; } fid e } nti if ( i % 2 == 0 ) *psize = i / 2; else return -1; return 0; Filename: eth_plc.c Qu #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "plc.h" #include "config.h" #define RCV_BUF_SIZE #define SND_BUF_SIZE #define MAX_PKT_LEN #define RCV_TO 1024 * 1 1024 * 1 256 1 /* Receive buffer size */ /* Send buffer size */ const char zero_mac[ETH_ALEN] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00}; struct eth_pkt { struct ether_header eth_head; char eth_data[0]; }__attribute__ ((__packed__)); nti Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e /* This is a list of interface name prefixes which are `bad' in the sense * that they don't refer to interfaces of external type on which we are * likely to want to listen. We also compare candidate interfaces to lo. */ static char *bad_interface_names[] = { "lo:", "lo", "stf", /* pseudo-device 6to4 tunnel interface */ "gif", /* psuedo-device generic tunnel interface */ "dummy", "vmnet", NULL /* last entry must be NULL */ }; page 22 al QCA-PLC-SG-firmware-application-notes v1.0.0 /* Receive buffer size */ static int rcv_buf_szie = RCV_BUF_SIZE; static char rcv_buff[RCV_BUF_SIZE] = { 0 }; /*Send buffer size*/ static int snd_buf_szie = SND_BUF_SIZE; static char snd_buff[SND_BUF_SIZE] = { 0 }; /* Interface name */ static char if_name[10] = "eth0"; /* Host MAC */ static char host_mac[ETH_ALEN] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; static char dest_mac[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; Qu static void reverse_char_array( char eth_mac[], int len ) { int i; char tmp; for (i = 0; i < len / 2; i++) { tmp = eth_mac[i]; eth_mac[i] = eth_mac[len - 1 - i]; eth_mac[len - 1 - i] = tmp; } } static void eth_show_mac(const int type, const char eth_mac[]) { int i = 0; if (0 == type) printf("SMAC=["); else printf("DMAC=["); for(i = 0; i < ETH_ALEN - 1; i++) printf("%02x:", *((unsigned char *)&(eth_mac[i]))); printf("%02x] ", *((unsigned char *)&(eth_mac[i]))); } nti Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n if (flags == 0) { /* reset promiscuous mode */ st_ifr.ifr_flags &= ~IFF_PROMISC; } /* Set promiscuous mode */ st_ifr.ifr_flags |= IFF_PROMISC; ret = ioctl(fd, SIOCSIFFLAGS, &st_ifr); fid e /* Set interface as promiscuous mode */ static int set_promisc( const char *ifname, int fd, int flags) { int ret = -1; struct ifreq st_ifr; /* Get interface flags */ strcpy( st_ifr.ifr_name, ifname); ret = ioctl(fd, SIOCGIFFLAGS, &st_ifr ); if (ret < 0) { perror("[Error]Get Interface Flags"); return -1; } page 23 al QCA-PLC-SG-firmware-application-notes v1.0.0 if (ret < 0) { perror("[Error]Set Interface Flags"); return -1; } return 0; } Qu int plc_init_socket( void ) { int ret = -1; int fd = -1; struct ifreq st_ifr; struct sockaddr_ll st_local = {0}; struct timeval rcv_timeout = {0, 10000}; /* 100 minisecond */ /* Create a socket */ fd = socket( PF_PACKET, SOCK_RAW, htons( ETH_P_ALL )); if (fd < 0) { perror("[Error]Initinate L2 raw socket"); return -1; } /* Set if name */ set_ifname( if_name ); /* Set the interface as promiscuous mode */ set_promisc( if_name, fd, 1 ); /* Set the timeout value of receiving, the default value is 0, which means will never time out */ ret = setsockopt( fd, SOL_SOCKET, SO_RCVTIMEO, (char*)&rcv_timeout, sizeof(struct timeval) ); nti fid e Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n if (ret < 0) { perror("[Error]Set socket receive timeout"); close(fd); return -1; } /* Get index of interface */ strcpy( st_ifr.ifr_name, if_name ); ret = ioctl(fd, SIOCGIFINDEX, &st_ifr); if (ret < 0) { perror("[Error]Ioctl operation"); close(fd); return -1; } /* Bind interface */ st_local.sll_family = PF_PACKET; st_local.sll_ifindex = st_ifr.ifr_ifindex; /*st_local.sll_protocol = htons( ETH_P_ALL );*/ st_local.sll_protocol = htons( ETH_P_HPAV ); ret = bind(fd, (struct sockaddr *)&st_local, sizeof(st_local) ); if (ret < 0) { perror("[Error]Bind the interface"); close(fd); return -1; } Qu if ( memcmp( host_mac, zero_mac, ETH_ALEN ) == 0) { /* Get MAC address */ ret = ioctl( fd, SIOCGIFHWADDR, &st_ifr ); if (ret < 0) { perror("[Error]Get the MAC address"); close(fd); return -1; } memcpy( host_mac, st_ifr.ifr_hwaddr.sa_data, sizeof(host_mac) ); } return fd; } int plc_exit_socket( fd ) { return close( fd ); } page 24 al QCA-PLC-SG-firmware-application-notes v1.0.0 QCA-PLC-SG-firmware-application-notes v1.0.0 page 25 *pp_packet = rcv_buff; return pkt_len; } nti Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n #ifdef DB_RCV_ETH_RAW int i; printf( "\nReceive raw ether frame:\n"); for (i = 0; i < pkt_len; i++) { printf( "%02X ", (unsigned char)(*pp_packet)[i] ); } printf( "\n" ); #endif fid e /* Receive frame */ memset( rcv_buff, 0, RCV_BUF_SIZE ); pkt_len = recvfrom( fd, rcv_buff, rcv_buf_szie, 0, NULL, NULL ); if (pkt_len < 0) { return -1; } al int eth_recv( const int fd, char** pp_packet) { int pkt_len = -1; int eth_plc_recv( const int fd, char* const plc_packet ) { int i; int pkt_len = -1; struct cmd_ind_hdr* p_packet = NULL; Qu i = 0; /*while (i++ <= RCV_RETRY_CNT)*/ time_t start_time; time_t current_time; start_time = time( (time_t*)NULL ); if (start_time < 0) { return -1; } do { current_time = time( (time_t*)NULL ); if (current_time < 0) { return -1; } QCA-PLC-SG-firmware-application-notes v1.0.0 page 26 pkt_len = eth_recv( fd, (char**)&p_packet ); if (pkt_len < 0) { continue; } Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n pkt_len -= CMD_IND_HDR_SZ; memcpy( plc_packet, p_packet->data, pkt_len ); return pkt_len; } } while (current_time - start_time < RCV_TO); return -1; } int eth_send( const int fd, const char* const packet, const int len ) { int ret = -1; int pkt_len = -1; int plc_addr_pos = 0; struct eth_pkt* eth_packet; /*char dest_mac[ETH_ALEN];*/ if (packet == NULL) return -1; Qu pkt_len = len; eth_packet = (struct eth_pkt*)malloc( pkt_len ); if (eth_packet == NULL) return -1; memcpy( eth_packet, packet, len ); /* Send packet */ pkt_len = sendto( fd, eth_packet, pkt_len, 0, NULL, 0 ); if (pkt_len < 0) { free( eth_packet ); return -1; } free( eth_packet ); return pkt_len; } fid e nti al if ( memcmp( dest_mac, p_packet->address, ETH_ALEN ) == 0 && p_packet->mmtype == MMTYPE_CMD_IND ) { if (pkt_len > MAX_PKT_LEN) { pkt_len = MAX_PKT_LEN; } QCA-PLC-SG-firmware-application-notes v1.0.0 page 27 al int eth_plc_send( const int fd, const char* const plc_packet, const int len ) { int ret = -1; int pkt_len = -1; int plc_addr_pos = 0; struct cmd_req_hdr* req_header; nti if (plc_packet == NULL) return -1; if (req_header == NULL) return -1; Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n /* Find the address starting position */ while (plc_packet[ plc_addr_pos++ ] != 0x68) { if (plc_addr_pos >= len) { free( req_header ); return -1; } } fid e pkt_len = len + CMD_REQ_HDR_SZ; req_header = (struct cmd_req_hdr*)malloc( pkt_len ); memcpy( dest_mac, (char*)plc_packet + plc_addr_pos, ETH_ALEN ); /*reverse_char_array( dest_mac, ETH_ALEN );*/ cmd_req_hdr_init( req_header, dest_mac, host_mac, len ); memcpy( req_header->data, plc_packet, len ); Qu #ifdef DB_SND_ETH_RAW int i; printf( "\nSend raw ether frame:\n"); for (i = 0; i < pkt_len; i++) { printf( "%02X ", (unsigned char)(((char*)req_header)[i])) ; } printf( "\n" ); #endif /* Send packet */ pkt_len = sendto( fd, req_header, pkt_len, 0, NULL, 0 ); if (pkt_len < 0) { free( req_header ); return -1; } free( req_header ); return pkt_len; } QCA-PLC-SG-firmware-application-notes v1.0.0 page 28 static int is_bad_interface_name(char *interface_name) { char **p; al for (p = bad_interface_names; *p; ++p) if (strncmp(interface_name, *p, strlen(*p)) == 0) return 1; return 0; Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n fid e /* This finds the first interface which is up and is not the loopback * interface or one of the interface types listed in bad_interface_names. */ int set_ifname( char interface_name[] ) { struct if_nameindex * nameindex; int i; nti } Qu nameindex = if_nameindex(); if(nameindex == NULL) { return -1; } /* Try to find a interface named if_name */ i = 0; while(nameindex[i].if_index != 0) { if (strcmp(nameindex[i].if_name, "lo") != 0 && !is_bad_interface_name(nameindex[i].if_name)) { if (strcmp( interface_name, nameindex[i].if_name ) == 0) { if_freenameindex(nameindex); return 0; } } i++; } /* If no interface named if_name is found, copy the first interface name found to if_name */ i = 0; while(nameindex[i].if_index != 0) { if (strcmp(nameindex[i].if_name, "lo") != 0 && !is_bad_interface_name(nameindex[i].if_name)) { strcpy( interface_name, nameindex[i].if_name ); if_freenameindex(nameindex); return 0; } i++; } return -1; } QCA-PLC-SG-firmware-application-notes v1.0.0 page 29 void plc_set_ifname( char interface_name[] ) { strcpy( if_name, interface_name ); } nti al void plc_set_host_mac( char mac_addr[] ) { int i; fid e for (i = 0; i < ETH_ALEN; i++) { host_mac[i] = mac_addr[i]; } Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n } Filename: config.h #ifdef DEBUG #define DB_SND_ETH_RAW #define DB_RCV_ETH_RAW #define DB_TEMP #endif Filename: main.c #include #include #include "common.h" #define COM_RETRY_CNT /*#define RCV_CNT 3 32*/ Qu const static char host_mac_addr[6] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; int main( int argc, char* argv[] ) { char recv_to_flag = 0; char input_flag = 1; /*char send_buf[32] = { 0 };*/ /*char input_buf[100];*/ char send_buf[1024] = { 0 }; char input_buf[1024]; int com_len; int str_len; char const send_com[32] = { 0xfe, 0xfe, 0xfe, 0xfe, 0x68, 0x32, 0x00, 0x00, 0x00, 0x00, 0x00, 0x68, 0x13, 0x00, 0x15, 0x16 }; char receive_buf[300]; int rcv_len = 0; int fd; int i; char *p; nti fid e plc_set_ifname( "eth0" ); plc_set_host_mac( host_mac_addr ); fd = plc_init_socket(); printf( "\n\n" ); printf("/********QCA7000 Remote meter module test********/"); printf( "\n" ); printf("FE FE FE 68 32 00 00 00 00 00 68 11 04 33 34 34 35 E7 16"); printf( "\n" ); printf("FE FE FE 68 32 00 00 00 00 00 68 11 04 33 34 35 35 E8 16"); while (1) { page 30 al QCA-PLC-SG-firmware-application-notes v1.0.0 Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n printf( "\n\n" ); printf("------------------------------------------------------------------"); while( 1 ) { printf( "\n" ); printf("Input: "); gets( input_buf ); if (str2hex( input_buf, send_buf, &com_len )) { printf( "\nInput error!\n"); } else { break; } } Qu if (eth_plc_send( fd, send_buf, com_len ) < 0 ) { printf( "\neth_send error\n" ); continue; } /* Retry COM_RETRY_CNT times */ for (i = 0; i < COM_RETRY_CNT; i++) { rcv_len = eth_plc_recv( fd, receive_buf ); if (rcv_len > 0) { str_len = find_char( receive_buf, rcv_len, 0x16 ); if (str_len > 0) break; else i--; } } if (i == COM_RETRY_CNT) printf( "\nReceive time out!" ); else { QCA-PLC-SG-firmware-application-notes v1.0.0 page 31 printf( "\nReceive %d data: ", str_len + 1 ); for (i = 0; i < str_len + 1; i++) printf( "%02X ", (unsigned char)receive_buf[i] ); } } plc_exit_socket( fd ); al } #CC = /opt/nxp/gcc-4.3.2-glibc-2.7/bin/arm-vfp-linux-gnu-gcc CC = gcc Fo alco D R r G r mm AF idc At T O om he r m os NL Co Y n all: $(TARGET) fid e TARGET = eth_plc_7000 OBJS = main.c common.c eth_plc.c plc.c nti Filename: makefile $(TARGET): $(OBJS) @$(CC) -I. -o $@ $(OBJS) @echo "Compile completed!" @#cp $(TARGET) ~/nfs_dir/for_lpc3250/test clean: Qu @rm -vf $(TARGET) *.o *~
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Qualcomm Atheros, Inc. Create Date : 2013:05:06 14:28:24+08:00 Keywords : QCA6410, HomePlug?, AV, MAC/PHY, Transceiver, Data, Sheet Modify Date : 2013:06:24 16:58:53+08:00 Subject : QCA6410 Data Sheet Has XFA : No Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Qualcomm Atheros, Inc. Description : QCA6410 Data Sheet Title : QCA6410 HomePlug?AV MAC/PHY Transceiver Data Sheet Creator Tool : Microsoft® Word 2010 Metadata Date : 2013:06:24 16:58:53+08:00 Producer : Microsoft® Word 2010 Document ID : uuid:274f2422-941c-491f-bcbd-a1bb333cce0d Instance ID : uuid:54a2f7b2-f079-4698-a468-bc6bd028a8a6 Page Count : 31EXIF Metadata provided by EXIF.tools