JSS4 TS Posh Dominique Link Toilet Suite 9502975 Tech Warranty

User Manual: JSS4-TS

Open the PDF directly: View PDF PDF.
Page Count: 3

POSH
LINK TOILET SUITE
SPECIFICATIONS
Recommended use Domestic, Hotel, and Commercial
Material Pan Vitreous China
Seat Plastic Link and Seat
Colour White
Weight Pan 18kg
Solus Cistern 12kg
Dominique Cistern 14kg
Water Inlet Left or right
Inlet Valve Recommended maximum working pressure 500kPa
Bowl Configuration S Trap only
Rim Configuration Box Rim
Seat Soft Close Seat and link piece (supplied)
Cistern fixing Cistern fixed to wall using corrosion resistant
brackets (supplied).
Pan fixing Pan screwed to floor using fixing bolts (not supplied)
and bedded with sealant.
Options - Performa S/S Pan Screws
To see the complete POSH range go to
www.reece.com.au/bathrooms
Licence No. 0025
A joint government and industry
program
The more
stars the more
water efficient
litres per full flush
litres per average flush
when tested in accordance with standard AS/NZS6400
For more information and to compare
products refer to:
3
litres per half flush
3.5
4.5
9505484 Posh Solus Link
Suite S Trap (4*)
Posh Solus Link S Trap Toilet Suite
170min - 280max
360
840
825-840
400
155
170
375
405
480 260
280
670min - 780max
170min - 280max
445170
375
360
825-840
410
367
Dimensions are nominal measurements only.
Cleaning ReCommendations
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
TM
WMKA 21192
AS/NZS 1172
360
280
170
670 min - 780 max
405
375 420
870
170 min - 280 max
870
9505484 Posh Solus Link
Suite S Trap (4*)
Posh Solus Link S Trap Toilet Suite
170min - 280max
360
840
825-840
400
155
170
375
405
480 260
280
670min - 780max
170min - 280max
445170
375
360
825-840
410
367
SOLUS
SOLUS
DOMINIQUE
DOMINIQUE
page 1 of 3
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered
trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from
their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs
listed are correct at time of publication however the manufacturer/distributor takes no responsibility for
printing errors.
Tech Page Version 1
INSTALLATION INSTRUCTIONS
1. Check that that pan is installed within dimensional tolerances. Place suite in position. Mark out the fixing holes for
the cistern (cistern should be fixed to a noggin or solid wall).
2. If required, modify flush pipe to fit pan and cistern.
3. To install the link piece, flush pipe and seat, refer to the instructions opposite.
POSH
LINK TOILET SUITE
6
2
1
3
4
5
31
1
1
2
2
1
1
2
2
2
Fit plastic bolts and slide nuts onto seat Position seat onto pan and align correctly
Draw line across back edge of the seat hinge.
Platform and remove seat.
Once flush pipe has been cut to correct length,
lubricate and fit keeseal to pipe. Mount cistern
onto wall at recommended height.
Once this is done, fit and tighten plastic
flush pipe nut.
Slide plastic link piece over flush pipe nut until it
locks into position
Mark off line on link piece to align with
previously drawn line (Diagram 3)
page 2 of 3
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
POSH
LINK TOILET SUITE
8
7
9 10
L
L- 10mm
remove link piece and...
Cut off as per distance (L) less 10mm.
Reinstall link piece
Reposition seat back onto pan and slightly
tighten seat fixing bolts
Slide/position seat into link piece
Fully tighten bolts to lock seat and link inot
position. Ensure all connections are secure
and water tight.
page 3 of 3
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference

Navigation menu